SPEC NO. 05-08-5223 REV. C RH1573K LOW DROPOUT PNP REGULATOR DRIVER DICE REVISION RECORD REV DESCRIPTION DATE 0 INITIAL RELEASE 09/22/08 A • PAGE 8, CHANGED OUT ORIGINAL BURN-IN CIRCUIT WITH THE ACTUAL BURN-IN CIRCUIT FROM 04-06-0689. • PAGE 13, CHANGED RH CANNED SAMPLE TABLE III FOR QUALIFYING DICE SALES ADDED TEMPERATURE CYCLE, CONSTANT ACCELERATION & REMOVED PIND TEST. Page 2, amended section 3.3 Special Handling of Dice to more accurately describe our current procedures and requirements. Page 13, Changed RH Canned Sample Table for Qualifying Dice Sales: Subgroup 6 Sample Size Series changed from 45 (3) to 65 (3). First note had the Sample Size Series from “15%” to “10%”. 03/03/09 B C 04/03/12 7/2/13 CAUTION: ELECTROSTATIC DISCHARGE SENSITIVE PART REVISION INDEX REVISION INDEX PAGE NO. REVISION PAGE NO. REVISION 1 C 2 C 3 C 4 C 5 C 6 C 7 C APPLICATION 9 C 10 C 11 C 12 C 13 C LINEAR TECHNOLOGY CORPORATION MILPITAS, CALIFORNIA TITLE: MICROCIRCUIT, LINEAR, RH1573K LOW DROPOUT PNP REGULATOR DRIVER DICE ORIG DSGN ENGR MFG CM QA PROG FUNCT 8 C SIZE SIGNOFFS DATE CAGE CODE DRAWING NUMBER REV 64155 05-08-5223 C CONTRACT: FOR OFFICIAL USE ONLY LINEAR TECHNOLOGY CORPORATION PAGE 1 OF13 SPEC NO. 05-08-5223 REV. C 1.0 SCOPE: 1.1 2.0 RH1573K LOW DROPOUT PNP REGULATOR DRIVER DICE This specification defines the performance and test requirements for a microcircuit processed to a space level manufacturing flow. APPLICABLE DOCUMENTS: 2.1 Government Specifications and Standards: the following documents listed in the Department of Defense Index of Specifications and Standards, of the issue in effect on the date of solicitation, form a part of this specification to the extent specified herein. SPECIFICATIONS: 2.2 3.0 MIL-PRF-38535 Integrated Circuits (Microcircuits) Manufacturing, General Specification for MIL-STD-883 Test Method and Procedures for Microcircuits MIL-STD-1835 Microcircuits Case Outlines Order of Precedence: In the event of a conflict between the documents referenced herein and the contents of this specification, the order of precedence shall be this specification, MIL-PRF-38535 and other referenced specifications. REQUIREMENTS: 3.1 General Description: This specification details the requirements for the RH1573K, DICE and Element Evaluation Test Samples, processed to space level manufacturing flow as specified herein. 3.2 Part Number: 3.3 Special Handling of Dice: Rad Hard dice require special handling as compared to standard IC dice. Rad Hard dice are susceptible to surface damage due to the absence of silicon nitride passivation that is present on most standard dice. Silicon nitride protects the dice surface from scratches by its hard and dense properties. The passivation on Linear Technology’s Rad Hard dice is silicon dioxide which is much “softer” than silicon nitride. . During the visual and preparation for shipment, ESD safe Tweezers are used and only the edge of the die are touched. RH1573K Dice LTC recommends that dice handling be performed with extreme care so as to protect the die surface from scratches. If the need arises to move the die in or out of the chip shipment tray (waffle pack), use an ESD-Safe-Plastic-tipped Bent Metal Vacuum Probe, preferably .020” OD x .010” ID (for use with tiny parts). The wand should be compatible with continuous air vacuums. The tip material should be static dissipative Delrin (or equivalent) plastic. During die attach, care must be exercised to ensure no tweezers, or other equipment, touch the top of the dice. LINEAR TECHNOLOGY CORPORATION PAGE 2 OF13 SPEC NO. 05-08-5223 REV. C 3.4 RH1573K LOW DROPOUT PNP REGULATOR DRIVER DICE The Absolute Maximum Ratings: . Input Pin Voltage (VIN TO GND) . Drive Pin Voltage (VDRIVE TO GND) . Output Pin Voltage (VOUT TO GND) Shutdown Pin Voltage (VSHDN TO GND) Operating Junction Temperature Range Storage Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10V . . . 10V . . . 10V . . . 10V -55°C to 125°C -65°C to 150°C 3.5 Design, Construction, and Physical Dimensions: Detail design, construction, physical dimensions, and electrical requirements shall be specified herein. 3.6 Outline Dimensions and Pad Functions: Dice outline dimensions, pad functions, and locations shall be specified in Figure 1. 3.7 Radiation Hardness Assurance (RHA): 3.7.1 The manufacturer shall perform a lot sample test as an internal process monitor for total dose radiation tolerance. The sample test is performed with MIL-STD-883 TM1019 Condition A as a guideline. 3.7.2 For guaranteed radiation performance to MIL-STD-883, Method 1019, total dose irradiation, the manufacturer will provide certified RAD testing and report through an independent test laboratory when required as a customer purchase order line item. 3.7.3 Total dose bias circuit is specified in Figure 2. 3.8 Wafer (or Dice) Probe: Dice shall be 100% probed at Ta = +25°C to the limits shown in Table I herein. All reject dice shall be removed from the lot. This testing is normally performed prior to dicing the wafer into chips. Final specifications after assembly are sample tested during the element evaluation. 3.9 Wafer Lot Acceptance: Wafer lot acceptance shall be in accordance with MIL-PRF-38535, Appendix A, except for the following: Top side glassivation thickness shall be a minimum of 4KÅ. 3.10 Wafer Lot Acceptance Report: SEM is performed per MIL-STD-883, Method 2018. Copies of SEM photographs shall be supplied with the Wafer Lot Acceptance Report as part of a Space Data Pack when specified as a customer purchase order line item. 3.11 Traceability: Wafer Diffusion Lot and Wafer traceability shall be maintained through Quality Conformance Inspection. 4.0 QUALITY CONFORMANCE INSPECTION: Quality Conformance Inspection shall consist of the tests and inspections specified herein. 5.0 SAMPLE ELEMENT EVALUATION: A sample from each wafer supplying dice shall be assembled and subjected to element evaluation per Table III herein. 5.1 100 Percent Visual Inspection: All dice supplied to this specification shall be inspected in accordance with MIL-STD-883, Method 2010, Condition A. All reject dice shall be removed from the lot. LINEAR TECHNOLOGY CORPORATION PAGE 3 OF13 SPEC NO. 05-08-5223 REV. C 6.0 RH1573K LOW DROPOUT PNP REGULATOR DRIVER DICE 5.2 Electrical Performance Characteristics for Element Evaluation: The electrical performance characteristics shall be as specified in Table I, Table II and Table III herein. 5.3 Sample Testing: Each wafer supplying dice for delivery to this specification shall be subjected to element evaluation sample testing. No dice shall be delivered until all the lot sample testing has been performed and the results found to be acceptable unless the customer supplies a written approval for shipment prior to completion of wafer qualification as specified in this specification. 5.4 Part Marking of Element Evaluation Sample Includes: 5.4.1 LTC Logo 5.4.2 LTC Part Number 5.4.3 Date Code 5.4.4 Serial Number 5.4.5 ESD Identifier per MIL-PRF-38535, Appendix A 5.4.6 Diffusion Lot Number 5.4.7 Wafer Number 5.5 Burn-In Requirement: Burn-In circuit for CERDIP / 8 lead package is specified in Figure 3. 5.6 Mechanical/Packaging Requirements: Case Outline and Dimensions are in accordance with Figure 4. 5.7 Terminal Connections: The terminal connections shall be as specified in Figure 5. 5.8 Lead Material and Finish: The lead material and finish shall be alloy 42 with hot solder dip (Finish letter A) in accordance with MIL-PRF-38535. VERIFICATION (QUALITY ASSURANCE PROVISIONS) 6.1 Quality Assurance Provisions: Quality Assurance provisions shall be in accordance with MIL-PRF38535. Linear Technology is a QML certified company and all Rad Hard candidates are assembled on qualified Class S manufacturing lines. 6.2 Sampling and Inspection: Sampling and Inspection shall be in accordance with Table III herein. 6.3 Screening: Screening requirements shall be in accordance with Table III herein. 6.4 Source Inspection: 6.4.1 The manufacturer will coordinate Source Inspection at wafer lot acceptance and pre-seal internal visual. 6.4.2 The procuring activity has the right to perform source inspection at the supplier’s facility prior to shipment for each lot of deliverables when specified as a customer purchase order line item. This may include wafer lot acceptance, die visual, and final data review. LINEAR TECHNOLOGY CORPORATION PAGE 4 OF13 SPEC NO. 05-08-5223 REV. C 6.5 RH1573K LOW DROPOUT PNP REGULATOR DRIVER DICE Deliverable Data: Deliverable data that will ship with devices when a Space Data Pack is ordered: 6.5.1 Lot Serial Number Sheets identifying all Canned Sample devices accepted through final inspection by serial number. 6.5.2 100% attributes (completed element evaluation traveler). 6.5.3 Element Evaluation variables data, including Burn-In and Op Life 6.5.4 SEM photographs (3.10 herein) 6.5.5 Wafer Lot Acceptance Report (3.9 herein) 6.5.6 A copy of outside test laboratory radiation report if ordered 6.5.7 Certificate of Conformance certifying that the devices meet all the requirements of this specification and have successfully completed the mandatory tests and inspections herein. Note: Items 6.5.1 and 6.5.7 will be delivered as a minimum, with each shipment. 7.0 Packaging Requirements: Packaging shall be in accordance with Appendix A of MIL-PRF-38535. All dice shall be packaged in multicavity containers composed of conductive, anti-static, or static dissipative material with an external conductive field shielding barrier. LINEAR TECHNOLOGY CORPORATION PAGE 5 OF13 SPEC NO. 05-08-5223 REV. C RH1573K LOW DROPOUT PNP REGULATOR DRIVER DICE DICE OUTLINE DIMENSIONS AND PAD FUNCTIONS FIGURE 1 LINEAR TECHNOLOGY CORPORATION PAGE 6 OF13 SPEC NO. 05-08-5223 REV. C RH1573K LOW DROPOUT PNP REGULATOR DRIVER DICE TOTAL DOSE BIAS CIRCUIT FIGURE 2 LINEAR TECHNOLOGY CORPORATION PAGE 7 OF13 SPEC NO. 05-08-5223 REV. C RH1573K LOW DROPOUT PNP REGULATOR DRIVER DICE BURN-IN CIRCUIT FIGURE 3 LINEAR TECHNOLOGY CORPORATION PAGE 8 OF13 SPEC NO. 05-08-5223 REV. C RH1573K LOW DROPOUT PNP REGULATOR DRIVER DICE (J) CERDIP / 8 LEADS, CASE OUTLINE θja = +110°C/W θjc = +30°C/W FIGURE 4 LINEAR TECHNOLOGY CORPORATION PAGE 9 OF13 SPEC NO. 05-08-5223 REV. C RH1573K LOW DROPOUT PNP REGULATOR DRIVER DICE TERMINAL CONNECTIONS FIGURE 5 LINEAR TECHNOLOGY CORPORATION PAGE 10 OF13 SPEC NO. 05-08-5223 REV. C RH1573K LOW DROPOUT PNP REGULATOR DRIVER DICE TABLE I DICE ELECTRICAL CHARACTERISTICS – ELEMENT EVALUATION TA = 25°C LINEAR TECHNOLOGY CORPORATION PAGE 11 OF13 SPEC NO. 05-08-5223 REV. C RH1573K LOW DROPOUT PNP REGULATOR DRIVER DICE TABLE II ELECTRICAL CHARACTERISTICS – Post-Irradiation TA = 25°C Note 2: Operating conditions are limited by maximum junction temperature. The regulated feedback or output voltage specification will not apply for all possible combinations of input voltage, drive voltage and drive current. When operating at maximum drive current, the drive voltage range must be limited. When operating at maximum input and drive voltage, the drive current must be limited. LINEAR TECHNOLOGY CORPORATION PAGE 12 OF13 SPEC NO. 05-08-5223 REV. C RH1573K LOW DROPOUT PNP REGULATOR DRIVER DICE TABLE III RH ELEMENT EVALUATION TABLE QUALIFICATION OF DICE SALES LINEAR TECHNOLOGY CORPORATION PAGE 13 OF 13