Download Databrief

STEVAL-ISA114V1
5 V/0.8 W wide-range 30 kHz buck converter
based on the VIPer06XS
Data brief
Description
This document describes a 5 V- 0.15 A power
supply set in buck topology with the VIPer06XS, a
new off-line high voltage converter by
STMicroelectronics, specifically developed for
non-isolated SMPS.
The features of the device include an 800 V
avalanche rugged power section, PWM operation
at 30 kHz with frequency jittering for lower EMI,
limiting current with adjustable set point, on-board
soft-start, safe auto-restart after a fault condition
and low standby power consumption.
Features
The available protection includes a thermal
shutdown with hysteresis, delayed overload
protection and open loop failure protection. All
protection is auto-restart mode.
• Universal input mains range:
– input voltage: 90 - 264 VAC
– frequency: 45 - 65 Hz
• Single-output voltage:
– 5 V @ 0.16 A continuous operation
• Fully protected against faults (overload,
feedback disconnection and overheating)
• EMI: according to EN55022-Class-B
July 2013
DocID025045 Rev 1
For further information contact your local STMicroelectronics sales office.
1/8
www.st.com
8
Adapter features
1
STEVAL-ISA114V1
Adapter features
The electrical specifications are given in Table 1, the schematic in Figure 1, and the bill of
material in Table 2.
Table 1. Electrical specifications
Parameter
Symbol
Value
VIN
[80 VAC; 265 VAC]
Output voltage
VOUT
5V
Max. output current
IOUT
0.16 A
Precision of output regulation
∆VOUT_LF
±5%
High frequency output voltage ripple
∆VOUT_HF
50 mV
Max. ambient operating temperature
TAMB
60 ºC
Input voltage range
Table 2. Bill of material
2/8
Name
Value
Description
C1
2.2 μF, 400 V
Electrolytic capacitor
Saxon
C2
2.2 μF, 400 V
Electrolytic capacitor
Saxon
C3
2.2 μF, 25 V
Ceramic capacitor
SMD: 0805
CFB
Not mounted
Ceramic capacitor
SMD: 0805
Cf
100 nF, 50 V
Ceramic capacitor
SMD: 0805
Cc
Not mounted
Ceramic capacitor
SMD: 0805
C7
22 nF, 25 V
Ceramic capacitor
SMD: 0805
Murata
C8
100 nF, 50 V
Ceramic capacitor
SMD: 0805
Murata
C9
100 μF, 25V
Electrolytic capacitor
D1
1N4007
High voltage rectifier
DO-41
Fairchild
D3
STTH1L06
High voltage ultra fast
rectifier
SMB (SOD87)
ST
D4
STTH1L06
High voltage ultra fast
rectifier
SMB (SOD87)
ST
Daux
Not mounted
Small signal diode
IC
VIPER06XS
High voltage converter
SSO-10
ST
L1
1 mH
Input filter inductor
SMD
Epcos
L2
RFB0810-681
0.68 mH power inductor
Coilcraft
R1
22 ohm
1 W resistor
Panasonic
R3
1 kohm, 1%
1/4 W resistor
DocID025045 Rev 1
Footprint
Manufacturer
Murata
Murata
Rubycon, ZL
series
SMD: 0805
Panasonic
STEVAL-ISA114V1
Adapter features
Table 2. Bill of material (continued)
Name
Value
Description
Footprint
Manufacturer
R4a
1.5 kohm, 1%
1/4 W resistor
SMD: 0805
Panasonic
R4b
22 kohm
1/4 W resistor
SMD: 0805
R5a
15 kohm
1/4 W resistor
SMD: 0805
R5b
0 ohm, 1%
1/4 W resistor
SMD: 0805
R6
Not mounted
1/4 W resistor
SMD: 0805
Rbl
10 kohm, 1%
1/4 W resistor
SMD: 0805
Panasonic
Panasonic
Figure 1. Schematic
AC IN
R1
D1
L1
R5a
R5b
DRAIN DRAIN DRAIN DRAIN DRAIN
R4a
C8
VIPer06XS
C1
D3
C2
GND VDD LIM
FB COMP
R4b
CFB
C3
Cf
Cc
R6
C7
D4
GND
R3
L2
Vout
C9
Rbl
GND
AM16734v1
DocID025045 Rev 1
3/8
Layout
2
STEVAL-ISA114V1
Layout
Figure 2. Layout (top)
AM16790v1
Figure 3. Layout (bottom)
AM16789v1
4/8
DocID025045 Rev 1
STEVAL-ISA114V1
Layout
Figure 4. Thermal measurement @ VIN = 80 VAC, full load (170 mA), 3.3 kohm bleeder
Figure 5. Thermal measurement @ VIN = 115 VAC, full load (170 mA) 3.3 kohm bleeder
Figure 6. Thermal measurement @ VIN = 230 VAC, full load (170 mA) 3.3 kohm bleeder
DocID025045 Rev 1
5/8
Layout
STEVAL-ISA114V1
Figure 7. Thermal measurement @ VIN = 265 VAC, full load (170 mA) 3.3 kohm bleeder
6/8
DocID025045 Rev 1
STEVAL-ISA114V1
3
Revision history
Revision history
Table 3. Document revision history
Date
Revision
24-Jul-2013
1
Changes
Initial release.
DocID025045 Rev 1
7/8
STEVAL-ISA114V1
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
ST PRODUCTS ARE NOT AUTHORIZED FOR USE IN WEAPONS. NOR ARE ST PRODUCTS DESIGNED OR AUTHORIZED FOR USE
IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH
PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B) AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR
ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED
FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN
WRITING OF SUCH USAGE, UNLESS A PRODUCT IS EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE,
AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS.
PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE DEEMED SUITABLE FOR USE IN AEROSPACE BY THE
CORRESPONDING GOVERNMENTAL AGENCY.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2013 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
8/8
DocID025045 Rev 1