CY8C24223A, CY8C24423A :Automotive - Extended Temperature PSoC® Programmable System-on-Chip

CY8C24223A, CY8C24423A
Automotive - Extended Temperature PSoC®
Programmable System-on-Chip
Features
■
AEC qualified
■
Powerful Harvard architecture processor
❐ M8C processor speeds up to 12 MHz
❐ 8x8 multiply, 32-bit accumulate
❐ Low power at high speed
❐ 4.75V to 5.25V operating voltage
❐ Automotive temperature range: -40°C to +125°C
■
■
■
■
■
Additional system resources
2
❐ I C™ slave, master, or multi-master operation up to 400 kHz
❐ Watchdog and Sleep timers
❐ User-configurable Low Voltage Detection (LVD)
❐ Integrated supervisory circuit
❐ On-chip precision voltage reference
■
Complete development tools
❐ Free development software (PSoC Designer™)
❐ Full Featured, In-Circuit Emulator (ICE) and Programmer
❐ Full speed emulation
❐ Complex breakpoint structure
❐ 128K bytes trace memory
Advanced peripherals (PSoC® blocks)
❐ Six rail-to-rail analog PSoC blocks provide:
• Up to 14-Bit Analog-to-Digital Converters (ADCs)
• Up to 9-Bit Digital-to-Analog Converters (DACs)
• Programmable Gain Amplifiers (PGAs)
• Programmable filters and comparators
❐ Four digital PSoC blocks provide:
• 8- to 32-bit timers and counters, 8- and 16-bit pulse-width
modulators (PWMs)
• CRC and PRS modules
• Full- or Half-Duplex UART
• SPI master or slave
• Connectable to all General Purpose I/O (GPIO) pins
❐ Complex peripherals by combining blocks
Logic Block Diagram
Port 2
Port 0
Analog
Drivers
PSoC CORE
System Bus
Global Digital Interconnect
SRAM
256 Bytes
Precision, programmable clocking
❐ Internal ±4% 24 MHz oscillator
❐ High accuracy 24 MHz with optional 32 kHz crystal and
Phase Locked Loop (PLL)
❐ Optional external oscillator, up to 24 MHz
❐ Internal low speed, low power oscillator for Watchdog and
Sleep functionality
SROM
Global Analog Interconnect
Flash 4K
CPU Core (M8C)
Interrupt
Controller
Sleep and
Watchdog
Multiple Clock Sources
(Includes IMO, ILO, PLL, and ECO)
DIGITAL SYSTEM
Flexible on-chip memory
❐ 4K bytes Flash program storage, 100 erase/write cycles
❐ 256 bytes SRAM data storage
❐ In-System Serial Programming (ISSP)
❐ Partial Flash updates
❐ Flexible protection modes
❐ EEPROM emulation in Flash
Programmable pin configurations
❐ 25 mA Sink, 10 mA Drive on all GPIO
❐ Pull up, pull down, High Z, strong, or open drain drive modes
on all GPIO
[1]
❐ Up to 12 analog inputs on GPIO
❐ Two 30 mA analog outputs on GPIO
❐ Configurable interrupt on all GPIO
Port 1
Digital
Clocks
ANALOG SYSTEM
Digital
Block
Array
Analog
Block
Array
(1 Row,
4 Blocks)
(2 Columns,
6 Blocks)
Multiply
Accum.
Decimator
I2C
Analog
Ref
Analog
Input
Muxing
POR and LVD
System Resets
Internal
Voltage
Ref.
SYSTEM RESOURCES
Note
1. There are eight standard analog inputs on the GPIO. The other four analog inputs connect from the GPIO directly to specific switched-capacitor block inputs. See
the PSoC Technical Reference Manual for more details
Cypress Semiconductor Corporation
Document Number: 38-12029 Rev. *L
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised March 11, 2014
CY8C24223A, CY8C24423A
Contents
PSoC Functional Overview .............................................. 3
PSoC Core .................................................................. 3
Digital System ............................................................. 3
Analog System ............................................................ 4
Additional System Resources ..................................... 5
PSoC Device Characteristics ...................................... 5
Getting Started .................................................................. 5
Application Notes ........................................................ 5
Development Kits ........................................................ 5
Training ....................................................................... 5
CYPros Consultants .................................................... 5
Solutions Library .......................................................... 5
Technical Support ....................................................... 5
Development Tools .......................................................... 6
PSoC Designer Software Subsystems ........................ 6
Designing with PSoC Designer ....................................... 7
Select User Modules ................................................... 7
Configure User Modules .............................................. 7
Organize and Connect ................................................ 7
Generate, Verify, and Debug ....................................... 7
Document Conventions ................................................... 8
Acronyms Used ........................................................... 8
Units of Measure ......................................................... 8
Numeric Naming .......................................................... 8
Pinouts .............................................................................. 9
20-Pin Part Pinout ...................................................... 9
28-Pin Part Pinout .................................................... 10
Document Number: 38-12029 Rev. *L
Registers ......................................................................... 11
Register Conventions ................................................ 11
Register Mapping Tables .......................................... 11
Electrical Specifications ................................................ 14
Absolute Maximum Ratings ....................................... 15
Operating Temperature ............................................ 15
DC Electrical Characteristics ..................................... 16
AC Electrical Characteristics ..................................... 21
Packaging Information ................................................... 28
Thermal Impedances ................................................ 29
Capacitance on Crystal Pins .................................... 29
Solder Reflow Specifications ..................................... 29
Development Tool Selection ......................................... 30
Software .................................................................... 30
Development Kits ...................................................... 30
Evaluation Tools ........................................................ 30
Device Programmers ................................................. 31
Accessories (Emulation and Programming) .............. 31
Ordering Information ...................................................... 32
Ordering Code Definitions ........................................ 32
Document History Page ................................................. 33
Sales, Solutions, and Legal Information ...................... 34
Worldwide Sales and Design Support ....................... 34
Products .................................................................... 34
PSoC® Solutions ...................................................... 34
Cypress Developer Community ................................. 34
Technical Support ..................................................... 34
Page 2 of 34
CY8C24223A, CY8C24423A
The PSoC family consists of many programmable
system-on-chips with on-chip Controller devices. These devices
are designed to replace multiple traditional microcontroller unit
(MCU)-based system components with one, low cost single-chip
programmable device. PSoC devices include configurable
blocks of analog and digital logic, and programmable
interconnects. This architecture enables the user to create
customized peripheral configurations that match the
requirements of each individual application. Additionally, a fast
CPU, Flash program memory, SRAM data memory, and
configurable I/O are included in a range of convenient pinouts
and packages.
Digital System
The Digital System is composed of four digital PSoC blocks.
Each block is an 8-bit resource that can be used alone or
combined with other blocks to form 8, 16, 24, and 32-bit
peripherals, which are called user modules.
Figure 1. Digital System Block Diagram
Port 1
Port 2
Port 0
To System Bus
Digital Clocks
From Core
The PSoC architecture, as shown in the Logic Block Diagram on
page 1, is comprised of four main areas: PSoC Core, Digital
System, Analog System, and System Resources. Configurable
global buses allow all the device resources to be combined into
a complete custom system. Each CY8C24x23A PSoC device
includes four digital blocks and six analog blocks. Depending on
the PSoC package, up to 24 GPIO are also included. The GPIO
provide access to the global digital and analog interconnects.
To Analog
System
DIGITAL SYSTEM
Digital PSoC Block Array
8
Row 0
DBB00
DBB01
DCB02
4
DCB03
4
8
Row Output
Configuration
8
Row Input
Configuration
PSoC Functional Overview
8
PSoC Core
GIE[7:0]
The PSoC Core is a powerful engine that supports a rich feature
set. The core includes a CPU, memory, clocks, and configurable
GPIO.
The M8C CPU core is a powerful processor with speeds up to
12 MHz, providing a two MIPS 8-bit Harvard architecture
microprocessor. The CPU uses an interrupt controller with
multiple vectors, to simplify programming of real time embedded
events. Program execution is timed and protected using the
included Sleep Timer and Watchdog Timer (WDT).
Memory includes 4 KB of Flash for program storage and 256
bytes of SRAM for data storage. Program Flash uses four
protection levels on blocks of 64 bytes, allowing customized
software IP protection.
The PSoC device incorporates flexible internal clock generators,
including a 24 MHz IMO (internal main oscillator) accurate to
±4% over temperature and voltage. A low power 32 kHz internal
low speed oscillator (ILO) is provided for the Sleep Timer and
WDT. If crystal accuracy is desired, the ECO (32.768 kHz
external crystal oscillator) is available for use as a Real Time
Clock (RTC) and can optionally generate a crystal-accurate
24 MHz system clock using a PLL. The clocks, together with
programmable clock dividers (as a System Resource), provide
the flexibility to integrate almost any timing requirement into the
PSoC device.
PSoC GPIOs provide connection to the CPU, digital, and analog
resources of the device. Each pin’s drive mode may be selected
from eight options, allowing great flexibility in external interfacing. Every pin also has the capability to generate a system
interrupt.
Document Number: 38-12029 Rev. *L
GIO[7:0]
Global Digital
Interconnect
GOE[7:0]
GOO[7:0]
Digital peripheral configurations include:
■
PWMs (8- and 16-bit)
■
PWMs with Dead Band (8- and 16-bit)
■
Counters (8 to 32 bit)
■
Timers (8 to 32 bit)
■
Full or Half-Duplex 8-bit UART with selectable parity
■
SPI master and slave
■
I2C master, slave, or multi-master
■
Cyclical Redundancy Checker/Generator (16 bit)
■
IrDA
■
Pseudo Random Sequence Generators (8 to 32 bit)
The digital blocks can be connected to any GPIO through a
series of global buses that can route any signal to any pin. The
buses also allow for signal multiplexing and for performing logic
operations. This configurability frees your designs from the
constraints of a fixed peripheral controller.
Digital blocks are provided in rows of four, where the number of
blocks varies by PSoC device family. This allows the optimum
choice of system resources for your application. Family
resources are shown in Table 1 on page 5.
Page 3 of 34
CY8C24223A, CY8C24423A
Analog System
The Analog System is composed of six configurable blocks, each
comprised of an opamp circuit allowing the creation of complex
analog signal flows. Analog peripherals are very flexible and can
be customized to support specific application requirements.
Some of the common PSoC analog functions for this device
(most available as user modules) are:
Figure 2. Analog System Block Diagram
P0[7]
P0[6]
P0[5]
P0[4]
P0[3]
P0[2]
P0[1]
P0[0]
ADCs (up to two, with 6 to 14-bit resolution, selectable as Incremental, Delta-Sigma, and SAR)
■
Filters (two and four pole band-pass, low-pass, and notch)
■
Amplifiers (up to two, with selectable gain up to 48x)
■
Instrumentation amplifiers (one with selectable gain up to 93x)
P2[3]
P2[2]
■
Comparators (up to two, with 16 selectable thresholds)
P2[1]
P2[0]
■
DACs (up to two, with 6 to 9-bit resolution)
■
Multiplying DACs (up to two, with 6 to 9-bit resolution)
■
High current output drivers (two with 30 mA drive)
■
1.3V reference (as a System Resource)
■
DTMF Dialer
■
Modulators
■
Correlators
■
Peak Detectors
■
Many other topologies possible
AGNDIn RefIn
■
P2[6]
P2[4]
Array Input Configuration
ACI0[1:0]
ACI1[1:0]
Block Array
Analog blocks are arranged in a column of three, which includes
one Continuous Time (CT) and two Switched Capacitor (SC)
blocks, as shown in Figure 2.
ACB00
ACB01
ASC10
ASD11
ASD20
ASC22
Analog Reference
Interface to
Digital System
RefHi
RefLo
AGND
Reference
Generators
AGNDIn
RefIn
BandGap
M8C Interface (Address Bus, Data Bus, Etc.)
Document Number: 38-12029 Rev. *L
Page 4 of 34
CY8C24223A, CY8C24423A
Additional System Resources
PSoC Device Characteristics
System Resources, some of which have been previously listed,
provide additional capability useful for complete systems.
Additional resources include a multiplier, decimator, low voltage
detection, and power on reset. Brief statements describing the
merits of each system resource follow:
Depending on your PSoC device characteristics, the digital and
analog systems can have a varying number of digital and analog
blocks. The following table lists the resources available for
specific PSoC device groups. The PSoC device covered by this
data sheet is highlighted in Table 1.
■
■
■
The I2C module provides 0 to 400 kHz communication over two
wires. Slave, master, and multi-master modes are all
supported.
LVD interrupts can signal the application of falling voltage
levels, while the advanced POR (Power On Reset) circuit
eliminates the need for a system supervisor.
An internal 1.3V voltage reference provides an absolute
reference for the analog system, including ADCs and DACs.
Analog
Columns
Analog
Blocks
up to
64
4
16
12
4
4
12
2K
32K
CY8C27x43
up to
44
2
8
12
4
4
12
256
Bytes
16K
CY8C24x94
64
Flash
Size
Analog
Outputs
CY8C29x66[2]
PSoC Part
Number
SRAM
Size
Analog
Inputs
The decimator provides a custom hardware filter for digital
signal processing applications including the creation of Delta
Sigma ADCs.
Digital
Blocks
■
A multiply accumulate (MAC) provides a fast 8-bit multiplier
with 32-bit accumulate, to assist in both general math as well
as digital filters.
Table 1. PSoC Device Characteristics
Digital
Rows
■
Digital clock dividers provide three customizable clock
frequencies for use in applications. The clocks can be routed
to both the digital and analog systems. Additional clocks can
be generated using digital PSoC blocks as clock dividers.
Digital
I/O
■
1
4
48
2
2
6
1K
16K
CY8C24x23A[2] up to
24
1
4
12
2
2
6
256
Bytes
4K
CY8C23x33
up to
1
4
12
2
2
4
256
Bytes
8K
CY8C21x34[2]
up to
28
1
4
28
0
2
4[3]
512
Bytes
8K
CY8C21x23
16
1
4
8
0
2
4[3]
256
Bytes
4K
CY8C20x34
up to
28
0
0
28
0
0
3[3, 4] 512
Bytes
8K
Getting Started
For in-depth information, along with detailed programming
details, see the PSoC® Technical Reference Manual.
CYPros Consultants
For up-to-date ordering, packaging, and electrical specification
information, see the latest PSoC device datasheets on the web.
Certified PSoC consultants offer everything from technical
assistance to completed PSoC designs. To contact or become a
PSoC consultant go to the CYPros Consultants web site.
Application Notes
Solutions Library
Cypress application notes are an excellent introduction to the
wide variety of possible PSoC designs.
Visit our growing library of solution focused designs. Here you
can find various application designs that include firmware and
hardware design files that enable you to complete your designs
quickly.
Development Kits
PSoC Development Kits are available online from and through a
growing number of regional and global distributors, which
include Arrow, Avnet, Digi-Key, Farnell, Future Electronics, and
Newark.
Training
Technical Support
Technical support – including a searchable Knowledge Base
articles and technical forums – is also available online. If you
cannot find an answer to your question, call our Technical
Support hotline at 1-800-541-4736.
Free PSoC technical training (on demand, webinars, and
workshops), which is available online via www.cypress.com,
covers a wide variety of topics and skill levels to assist you in
your designs.
Notes
2. Automotive qualified devices available in this group.
3. Limited analog functionality.
4. Two analog blocks and one CapSense™ block.
Document Number: 38-12029 Rev. *L
Page 5 of 34
CY8C24223A, CY8C24423A
Development Tools
Code Generation Tools
PSoC Designer™ is the revolutionary integrated design
environment (IDE) that you can use to customize PSoC to meet
your specific application requirements. PSoC Designer software
accelerates system design and time to market. Develop your
applications using a library of precharacterized analog and digital
peripherals (called user modules) in a drag-and-drop design
environment. Then, customize your design by leveraging the
dynamically generated application programming interface (API)
libraries of code. Finally, debug and test your designs with the
integrated debug environment, including in-circuit emulation and
standard software debug features. PSoC Designer includes:
The code generation tools work seamlessly within the
PSoC Designer interface and have been tested with a full range
of debugging tools. You can develop your design in C, assembly,
or a combination of the two.
Assemblers. The assemblers allow you to merge assembly
code seamlessly with C code. Link libraries automatically use
absolute addressing or are compiled in relative mode, and are
linked with other software modules to get absolute addressing.
■
Application editor graphical user interface (GUI) for device and
user module configuration and dynamic reconfiguration
■
Extensive user module catalog
C Language Compilers. C language compilers are available
that support the PSoC family of devices. The products allow you
to create complete C programs for the PSoC family devices. The
optimizing C compilers provide all of the features of C, tailored
to the PSoC architecture. They come complete with embedded
libraries providing port and bus operations, standard keypad and
display support, and extended math functionality.
■
Integrated source-code editor (C and assembly)
Debugger
■
Free C compiler with no size restrictions or time limits
■
Built-in debugger
■
In-circuit emulation
PSoC Designer has a debug environment that provides
hardware in-circuit emulation, allowing you to test the program in
a physical system while providing an internal view of the PSoC
device. Debugger commands allow you to read and program and
read and write data memory, and read and write I/O registers.
You can read and write CPU registers, set and clear breakpoints,
and provide program run, halt, and step control. The debugger
also allows you to create a trace buffer of registers and memory
locations of interest.
Built-in support for communication interfaces:
2
❐ Hardware and software I C slaves and masters
❐ Full-speed USB 2.0
❐ Up to four full-duplex universal asynchronous receiver/transmitters (UARTs), SPI master and slave, and wireless
PSoC Designer supports the entire library of PSoC 1 devices and
runs on Windows XP, Windows Vista, and Windows 7.
■
PSoC Designer Software Subsystems
Design Entry
In the chip-level view, choose a base device to work with. Then
select different onboard analog and digital components that use
the PSoC blocks, which are called user modules. Examples of
user modules are ADCs, DACs, amplifiers, and filters. Configure
the user modules for your chosen application and connect them
to each other and to the proper pins. Then generate your project.
This prepopulates your project with APIs and libraries that you
can use to program your application.
The tool also supports easy development of multiple configurations and dynamic reconfiguration. Dynamic reconfiguration
makes it possible to change configurations at run time. In
essence, this allows you to use more than 100 percent of PSoC's
resources for an application.
Document Number: 38-12029 Rev. *L
Online Help System
The online help system displays online, context-sensitive help.
Designed for procedural and quick reference, each functional
subsystem has its own context-sensitive help. This system also
provides tutorials and links to FAQs and an online support Forum
to aid the designer.
In-Circuit Emulator
A low-cost, high-functionality in-circuit emulator (ICE) is
available for development support. This hardware can program
single devices.
The emulator consists of a base unit that connects to the PC
using a USB port. The base unit is universal and operates with
all PSoC devices. Emulation pods for each device family are
available separately. The emulation pod takes the place of the
PSoC device in the target board and performs full-speed
(24 MHz) operation.
Page 6 of 34
CY8C24223A, CY8C24423A
Designing with PSoC Designer
The development process for the PSoC device differs from that
of a traditional fixed function microprocessor. The configurable
analog and digital hardware blocks give the PSoC architecture a
unique flexibility that pays dividends in managing specification
change during development and by lowering inventory costs.
These configurable resources, called PSoC Blocks, have the
ability to implement a wide variety of user-selectable functions.
The PSoC development process is summarized in four steps:
1. Select User Modules.
2. Configure User Modules.
3. Organize and Connect.
4. Generate, Verify, and Debug.
Select User Modules
PSoC Designer provides a library of prebuilt, pretested hardware
peripheral components called “user modules.” User modules
make selecting and implementing peripheral devices, both
analog and digital, simple.
Configure User Modules
Each user module that you select establishes the basic register
settings that implement the selected function. They also provide
parameters and properties that allow you to tailor their precise
configuration to your particular application. For example, a PWM
User Module configures one or more digital PSoC blocks, one
for each 8 bits of resolution. The user module parameters permit
you to establish the pulse width and duty cycle. Configure the
parameters and properties to correspond to your chosen
application. Enter values directly or by selecting values from
drop-down menus. All the user modules are documented in
datasheets that may be viewed directly in PSoC Designer or on
the Cypress website. These user module datasheets explain the
internal operation of the user module and provide performance
specifications. Each datasheet describes the use of each user
Document Number: 38-12029 Rev. *L
module parameter, and other information you may need to
successfully implement your design.
Organize and Connect
You build signal chains at the chip level by interconnecting user
modules to each other and the I/O pins. You perform the
selection, configuration, and routing so that you have complete
control over all on-chip resources.
Generate, Verify, and Debug
When you are ready to test the hardware configuration or move
on to developing code for the project, you perform the “Generate
Configuration Files” step. This causes PSoC Designer to
generate source code that automatically configures the device to
your specification and provides the software for the system. The
generated code provides application programming interfaces
(APIs) with high-level functions to control and respond to
hardware events at run-time and interrupt service routines that
you can adapt as needed.
A complete code development environment allows you to
develop and customize your applications in either C, assembly
language, or both.
The last step in the development process takes place inside
PSoC Designer’s debugger (access by clicking the Connect
icon). PSoC Designer downloads the HEX image to the ICE
where it runs at full speed. PSoC Designer debugging capabilities rival those of systems costing many times more. In addition
to traditional single-step, run-to-breakpoint, and watch-variable
features, the debug interface provides a large trace buffer and
allows you to define complex breakpoint events. These include
monitoring address and data bus values, memory locations, and
external signals.
Page 7 of 34
CY8C24223A, CY8C24423A
Document Conventions
Units of Measure
Acronyms Used
A units of measure table is located in the Electrical Specifications
section. Table 8 on page 14 lists all the abbreviations used to
measure the PSoC devices.
The following table lists the acronyms that are used in this
document.
Table 2. Acronyms
Acronym
Description
AC
alternating current
ADC
analog-to-digital converter
API
application programming interface
CPU
central processing unit
CT
continuous time
DAC
digital-to-analog converter
DC
direct current
ECO
external crystal oscillator
Numeric Naming
Hexadecimal numbers are represented with all letters in
uppercase with an appended lowercase ‘h’ (for example, ‘14h’ or
‘3Ah’). Hexadecimal numbers may also be represented by a ‘0x’
prefix, the C coding convention. Binary numbers have an
appended lowercase ‘b’ (for example, ‘01010100b’ or
‘01000011b’). Numbers not indicated by an ‘h’, ‘b’, or ‘0x’ are
decimal.
EEPROM electrically erasable programmable read-only
memory
FSR
full scale range
GPIO
general purpose I/O
GUI
graphical user interface
HBM
human body model
ICE
in-circuit emulator
ILO
internal low speed oscillator
IMO
internal main oscillator
I/O
input/output
IPOR
imprecise power on reset
LSb
least-significant bit
LVD
low voltage detect
MSb
most-significant bit
PC
program counter
PLL
phase-locked loop
POR
power on reset
PPOR
precision power on reset
PSoC®
Programmable System-on-Chip
PWM
pulse width modulator
SC
switched capacitor
SRAM
static random access memory
Document Number: 38-12029 Rev. *L
Page 8 of 34
CY8C24223A, CY8C24423A
Pinouts
The automotive CY8C24x23A PSoC device is available in a variety of packages which are listed and illustrated in the following tables.
Every port pin (labeled with a “P”) is capable of Digital I/O. However, Vss, Vdd, and XRES are not capable of Digital I/O.
20-Pin Part Pinout
Table 3. 20-Pin Part Pinout (SSOP)
Pin
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Type
Pin
Description
Digital Analog Name
I/O
I
P0[7] Analog column mux input
I/O
I/O
P0[5] Analog column mux input and column
output
I/O
I/O
P0[3] Analog column mux input and column
output
I/O
I
P0[1] Analog column mux input
Power
Vss
Ground connection
I/O
P1[7] I2C Serial Clock (SCL)
I/O
P1[5] I2C Serial Data (SDA)
I/O
P1[3]
I/O
P1[1] Crystal Input (XTALin), I2C Serial Clock
(SCL), ISSP-SCLK[5]
Power
Vss
Ground connection
I/O
P1[0] Crystal Output (XTALout), I2C Serial Data
(SDA), ISSP-SDATA[5]
I/O
P1[2]
I/O
P1[4] Optional External Clock Input (EXTCLK)
I/O
P1[6]
Input
XRES Active high external reset with internal pull
down
I/O
I
P0[0] Analog column mux input
I/O
I
P0[2] Analog column mux input
I/O
I
P0[4] Analog column mux input
I/O
I
P0[6] Analog column mux input
Power
Vdd
Supply voltage
Figure 3. CY8C24223A 20-Pin PSoC Device
AI, P0[7]
AIO, P0[5]
AIO, P0[3]
AI, P0[1]
Vss
I2C SCL, P1[7]
I2C SDA, P1[5]
P1[3]
I2C SCL, XTALin, P1[1]
Vss
1
2
3
4
5
6
7
8
9
10
SSOP
20
19
18
17
16
15
14
13
12
11
Vdd
P0[6], AI
P0[4], AI
P0[2], AI
P0[0], AI
XRES
P1[6]
P1[4], EXTCLK
P1[2]
P1[0], XTALout, I2C SDA
LEGEND: A = Analog, I = Input, and O = Output.
Note
5. These are the ISSP pins, which are not High Z when coming out of POR (Power On Reset). See the PSoC Technical Reference Manual for details.
Document Number: 38-12029 Rev. *L
Page 9 of 34
CY8C24223A, CY8C24423A
28-Pin Part Pinout
Table 4. 28-Pin Part Pinout (SSOP)
Type
Pin
Pin
Description
No. Digital Analog Name
1
I/O
I
P0[7] Analog column mux input
2
I/O
I/O
P0[5] Analog column mux input and column
output
3
I/O
I/O
P0[3] Analog column mux input and column
output
4
I/O
I
P0[1] Analog column mux input
5
I/O
P2[7]
6
I/O
P2[5]
7
I/O
I
P2[3] Direct switched capacitor block input
8
I/O
I
P2[1] Direct switched capacitor block input
9
Power
Vss
Ground connection
10
I/O
P1[7] I2C Serial Clock (SCL)
11
I/O
P1[5] I2C Serial Data (SDA)
12
I/O
P1[3]
13
I/O
P1[1] Crystal Input (XTALin), I2C Serial Clock
(SCL), ISSP-SCLK[5]
14
Power
Vss
Ground connection
15
I/O
P1[0] Crystal Output (XTALout), I2C Serial Data
(SDA), ISSP-SDATA[5]
16
I/O
P1[2]
17
I/O
P1[4] Optional External Clock Input (EXTCLK)
18
I/O
P1[6]
19
Input
XRES Active high external reset with internal
pull down
20
I/O
I
P2[0] Direct switched capacitor block input
21
I/O
I
P2[2] Direct switched capacitor block input
22
I/O
P2[4] External Analog Ground (AGND)
23
I/O
P2[6] External Voltage Reference (VRef)
24
I/O
I
P0[0] Analog column mux input
25
I/O
I
P0[2] Analog column mux input
26
I/O
I
P0[4] Analog column mux input
27
I/O
I
P0[6] Analog column mux input
28
Power
Vdd
Supply voltage
Figure 4. CY8C24423A 28-Pin PSoC Device
AI, P0[7]
AIO, P0[5]
AIO, P0[3]
AI, P0[1]
P2[7]
P2[5]
AI, P2[3]
AI, P2[1]
Vss
I2C SCL, P1[7]
I2C SDA, P1[5]
P1[3]
I2C SCL, XTALin, P1[1]
Vss
1
2
3
4
5
6
7
8
9
10
11
12
13
14
SSOP
28
27
26
25
24
23
22
21
20
19
18
17
16
15
Vdd
P0[6], AI
P0[4], AI
P0[2], AI
P0[0], AI
P2[6], External VRef
P2[4], External AGND
P2[2], AI
P2[0], AI
XRES
P1[6]
P1[4], EXTCLK
P1[2]
P1[0], XTALout, I2C SDA
LEGEND: A = Analog, I = Input, and O = Output.
Document Number: 38-12029 Rev. *L
Page 10 of 34
CY8C24223A, CY8C24423A
Registers
Register Conventions
Register Mapping Tables
This section lists the registers of the automotive CY8C24x23A
PSoC device. For detailed register information, refer to the PSoC
Technical Reference Manual.
The PSoC device has a total register address space of 512
bytes. The register space is referred to as I/O space and is
divided into two banks. The XIO bit in the Flag register (CPU_F)
determines which bank the user is currently in. When the XIO bit
is set the user is in Bank 1.
The register conventions specific to this section are listed in the
following table.
Table 5. Abbreviations
Convention
R
Note In the following register mapping tables, blank fields are
Reserved and must not be accessed.
Description
Read register or bit(s)
W
Write register or bit(s)
L
Logical register or bit(s)
C
Clearable register or bit(s)
#
Access is bit specific
Document Number: 38-12029 Rev. *L
Page 11 of 34
CY8C24223A, CY8C24423A
Table 6. Register Map Bank 0 Table: User Space
Name
PRT0DR
PRT0IE
PRT0GS
PRT0DM2
PRT1DR
PRT1IE
PRT1GS
PRT1DM2
PRT2DR
PRT2IE
PRT2GS
PRT2DM2
Addr (0,Hex) Access
Name
Addr (0,Hex)
00
RW
40
01
RW
41
02
RW
42
03
RW
43
04
RW
44
05
RW
45
06
RW
46
07
RW
47
08
RW
48
09
RW
49
0A
RW
4A
0B
RW
4B
0C
4C
0D
4D
0E
4E
0F
4F
10
50
11
51
12
52
13
53
14
54
15
55
16
56
17
57
18
58
19
59
1A
5A
1B
5B
1C
5C
1D
5D
1E
5E
1F
5F
DBB00DR0
20
#
AMX_IN
60
DBB00DR1
21
W
61
DBB00DR2
22
RW
62
DBB00CR0
23
#
ARF_CR
63
DBB01DR0
24
#
CMP_CR0
64
DBB01DR1
25
W
ASY_CR
65
DBB01DR2
26
RW
CMP_CR1
66
DBB01CR0
27
#
67
DCB02DR0
28
#
68
DCB02DR1
29
W
69
DCB02DR2
2A
RW
6A
DCB02CR0
2B
#
6B
DCB03DR0
2C
#
6C
DCB03DR1
2D
W
6D
DCB03DR2
2E
RW
6E
DCB03CR0
2F
#
6F
30
ACB00CR3
70
31
ACB00CR0
71
32
ACB00CR1
72
33
ACB00CR2
73
34
ACB01CR3
74
35
ACB01CR0
75
36
ACB01CR1
76
37
ACB01CR2
77
38
78
39
79
3A
7A
3B
7B
3C
7C
3D
7D
3E
7E
3F
7F
Blank fields are Reserved and must not be accessed.
Document Number: 38-12029 Rev. *L
Access
RW
RW
#
#
RW
RW
RW
RW
RW
RW
RW
RW
RW
Name
ASC10CR0
ASC10CR1
ASC10CR2
ASC10CR3
ASD11CR0
ASD11CR1
ASD11CR2
ASD11CR3
Addr (0,Hex)
80
81
82
83
84
85
86
87
88
89
8A
8B
8C
8D
8E
8F
ASD20CR0
90
ASD20CR1
91
ASD20CR2
92
ASD20CR3
93
ASC21CR0
94
ASC21CR1
95
ASC21CR2
96
ASC21CR3
97
98
99
9A
9B
9C
9D
9E
9F
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
AA
AB
AC
AD
AE
AF
RDI0RI
B0
RDI0SYN
B1
RDI0IS
B2
RDI0LT0
B3
RDI0LT1
B4
RDI0RO0
B5
RDI0RO1
B6
B7
B8
B9
BA
BB
BC
BD
BE
BF
# Access is bit specific.
Access
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
Name
I2C_CFG
I2C_SCR
I2C_DR
I2C_MSCR
INT_CLR0
INT_CLR1
INT_CLR3
INT_MSK3
INT_MSK0
INT_MSK1
INT_VC
RES_WDT
DEC_DH
DEC_DL
DEC_CR0
DEC_CR1
MUL_X
MUL_Y
MUL_DH
MUL_DL
ACC_DR1
ACC_DR0
ACC_DR3
ACC_DR2
RW
RW
RW
RW
RW
RW
RW
CPU_F
CPU_SCR1
CPU_SCR0
Addr (0,Hex)
C0
C1
C2
C3
C4
C5
C6
C7
C8
C9
CA
CB
CC
CD
CE
CF
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
DA
DB
DC
DD
DE
DF
E0
E1
E2
E3
E4
E5
E6
E7
E8
E9
EA
EB
EC
ED
EE
EF
F0
F1
F2
F3
F4
F5
F6
F7
F8
F9
FA
FB
FC
FD
FE
FF
Access
RW
#
RW
#
RW
RW
RW
RW
RW
RW
RC
W
RC
RC
RW
RW
W
W
R
R
RW
RW
RW
RW
RL
#
#
Page 12 of 34
CY8C24223A, CY8C24423A
Table 7. Register Map Bank 1 Table: Configuration Space
Name
PRT0DM0
PRT0DM1
PRT0IC0
PRT0IC1
PRT1DM0
PRT1DM1
PRT1IC0
PRT1IC1
PRT2DM0
PRT2DM1
PRT2IC0
PRT2IC1
Addr (1,Hex) Access
Name
Addr (1,Hex)
00
RW
40
01
RW
41
02
RW
42
03
RW
43
04
RW
44
05
RW
45
06
RW
46
07
RW
47
08
RW
48
09
RW
49
0A
RW
4A
0B
RW
4B
0C
4C
0D
4D
0E
4E
0F
4F
10
50
11
51
12
52
13
53
14
54
15
55
16
56
17
57
18
58
19
59
1A
5A
1B
5B
1C
5C
1D
5D
1E
5E
1F
5F
DBB00FN
20
RW
CLK_CR0
60
DBB00IN
21
RW
CLK_CR1
61
DBB00OU
22
RW
ABF_CR0
62
23
AMD_CR0
63
DBB01FN
24
RW
64
DBB01IN
25
RW
65
DBB01OU
26
RW
AMD_CR1
66
27
ALT_CR0
67
DCB02FN
28
RW
68
DCB02IN
29
RW
69
DCB02OU
2A
RW
6A
2B
6B
DCB03FN
2C
RW
6C
DCB03IN
2D
RW
6D
DCB03OU
2E
RW
6E
2F
6F
30
ACB00CR3
70
31
ACB00CR0
71
32
ACB00CR1
72
33
ACB00CR2
73
34
ACB01CR3
74
35
ACB01CR0
75
36
ACB01CR1
76
37
ACB01CR2
77
38
78
39
79
3A
7A
3B
7B
3C
7C
3D
7D
3E
7E
3F
7F
Blank fields are Reserved and must not be accessed.
Document Number: 38-12029 Rev. *L
Access
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
Name
ASC10CR0
ASC10CR1
ASC10CR2
ASC10CR3
ASD11CR0
ASD11CR1
ASD11CR2
ASD11CR3
Addr (1,Hex)
80
81
82
83
84
85
86
87
88
89
8A
8B
8C
8D
8E
8F
ASD20CR0
90
ASD20CR1
91
ASD20CR2
92
ASD20CR3
93
ASC21CR0
94
ASC21CR1
95
ASC21CR2
96
ASC21CR3
97
98
99
9A
9B
9C
9D
9E
9F
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
AA
AB
AC
AD
AE
AF
RDI0RI
B0
RDI0SYN
B1
RDI0IS
B2
RDI0LT0
B3
RDI0LT1
B4
RDI0RO0
B5
RDI0RO1
B6
B7
B8
B9
BA
BB
BC
BD
BE
BF
# Access is bit specific.
Access
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
Name
GDI_O_IN
GDI_E_IN
GDI_O_OU
GDI_E_OU
OSC_GO_EN
OSC_CR4
OSC_CR3
OSC_CR0
OSC_CR1
OSC_CR2
VLT_CR
VLT_CMP
IMO_TR
ILO_TR
BDG_TR
ECO_TR
RW
RW
RW
RW
RW
RW
RW
CPU_F
CPU_SCR1
CPU_SCR0
Addr (1,Hex)
C0
C1
C2
C3
C4
C5
C6
C7
C8
C9
CA
CB
CC
CD
CE
CF
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
DA
DB
DC
DD
DE
DF
E0
E1
E2
E3
E4
E5
E6
E7
E8
E9
EA
EB
EC
ED
EE
EF
F0
F1
F2
F3
F4
F5
F6
F7
F8
F9
FA
FB
FC
FD
FE
FF
Access
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
R
W
W
RW
W
RL
#
#
Page 13 of 34
CY8C24223A, CY8C24423A
Electrical Specifications
This section presents the DC and AC electrical specifications of the automotive CY8C24x23A PSoC device. For the latest electrical
specifications, visit http://www.cypress.com.
Specifications are valid for -40C  TA  125C and TJ  135C, except where noted.
Figure 5. Voltage versus CPU Frequency
5.25
l i d i ng
Va rat n
pe i o
O eg
R
4.75
Vdd Voltage (V)
0
12 MHz
93 kHz
24 MHz
CPU Frequency
(nominal setting)
The following table lists the units of measure that are used in this section.
Table 8. Units of Measure
Symbol
C
dB
fF
Hz
KB
Kbit
kHz
k
Mbaud
Mbps
MHz
M
A
F
H
s
V
Unit of Measure
degree Celsius
decibels
femto farad
hertz
1024 bytes
1024 bits
kilohertz
kilohm
megabaud
megabits per second
megahertz
megaohm
microampere
microfarad
microhenry
microsecond
microvolts
Document Number: 38-12029 Rev. *L
Symbol
Vrms
W
mA
ms
mV
nA
ns
nV

pA
pF
pp
ppm
ps
sps

V
Unit of Measure
microvolts root-mean-square
microwatts
milli-ampere
milli-second
milli-volts
nanoampere
nanosecond
nanovolts
ohm
picoampere
picofarad
peak-to-peak
parts per million
picosecond
samples per second
sigma: one standard deviation
volts
Page 14 of 34
CY8C24223A, CY8C24423A
Absolute Maximum Ratings
Exceeding maximum ratings may shorten the useful life of the device. User guidelines are not tested.
Table 9. Absolute Maximum Ratings
Symbol
TSTG
Description
Storage Temperature
TBAKETEMP
Bake Temperature
TBAKETIME
Bake Time
TA
Vdd
VIO
VIOZ
IMIO
ESD
LU
Ambient Temperature with Power Applied
Supply Voltage on Vdd Relative to Vss
DC Input Voltage
DC Voltage Applied to Tri-state
Maximum Current into any Port Pin
Electro Static Discharge Voltage
Latch up Current
Min
-55
Typ
+25
Max
+125
Units
Notes
C Higher storage temperatures
reduce data retention time.
Recommended storage temperature is +25°C ± 25°C. Storage
temperatures above 65C
degrades reliability. Maximum
combined storage and operational time at +125°C is 7000
hours.
C
–
125
See
package
label
-40
-0.5
Vss - 0.5
Vss - 0.5
-25
2000
–
–
See
package
label
72
Hours
–
–
–
–
–
–
–
+125
+6.0
Vdd + 0.5
Vdd + 0.5
+25
–
200
C
V
V
V
mA
V
mA
Min
-40
-40
Typ
–
–
Max
+125
+135
Human Body Model ESD.
Operating Temperature
Table 10. Operating Temperature
Symbol
TA
TJ
Description
Ambient Temperature
Junction Temperature
Document Number: 38-12029 Rev. *L
Units
Notes
C
C The temperature rise from
ambient to junction is package
specific. See Thermal Impedances on page 29. The user
must limit the power
consumption to comply with this
requirement.
Page 15 of 34
CY8C24223A, CY8C24423A
DC Electrical Characteristics
DC Chip-Level Specifications
The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C  TA  125°C. Typical parameters apply to 5V at 25°C and are for design guidance only.
Table 11. DC Chip-Level Specifications
Symbol
Description
Min
Typ
Max
Units
Notes
Vdd
Supply Voltage
4.75
–
5.25
V
See table titled DC POR and LVD
Specifications on page 20
IDD
Supply Current
–
5
8
mA
Conditions are Vdd = 5.25V, -40C  TA
 125C, CPU = 3 MHz, 48 MHz
disabled, VC1 = 1.5 MHz,
VC2 = 93.75 kHz, VC3 = 93.75 kHz,
Analog power = off.
ISB
Sleep (Mode) Current with POR, LVD, Sleep
Timer, and WDT.[6]
–
4
13
A
Conditions are with internal low speed
oscillator active, Vdd = 5.25V, -40C 
TA  55C. Analog power = off.
ISBH
Sleep (Mode) Current with POR, LVD, Sleep
Timer, and WDT at high temperature.[6]
–
4
100
A
Conditions are with internal slow
speed oscillator active, Vdd = 5.25V,
55C < TA  125C. Analog power = off.
ISBXTL
Sleep (Mode) Current with POR, LVD, Sleep
Timer, WDT, and external crystal.[6]
–
6
15
A
Conditions are with properly loaded, 1
W max, 32.768 kHz crystal.
Vdd = 5.25V, -40C  TA  55C.
Analog power = off.
ISBXTLH
Sleep (Mode) Current with POR, LVD, Sleep
Timer, WDT, and external crystal at high
temperature.[6]
–
6
100
A
Conditions are with properly loaded,
1W max, 32.768 kHz crystal.
Vdd = 5.25V, 55C < TA  125C.
Analog power = off.
VREF
Reference Voltage (Bandgap)
1.25
1.3
1.35
V
Trimmed for appropriate Vdd.
DC General Purpose I/O Specifications
The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C  TA  125°C. Typical parameters apply to 5V at 25°C and are for design guidance.
Table 12. DC GPIO Specifications
Symbol
Description
Min
Typ
Max
Units
4
5.6
8
k
Pull down Resistor
4
5.6
8
k
High Output Level
3.5
–
–
V
IOH = 10 mA, Vdd = 4.75 to 5.25V
(maximum 40 mA on even port pins
(for example, P0[2], P1[4]), maximum
40 mA on odd port pins (for example,
P0[3], P1[5])). 80 mA maximum
combined IOH budget.
VOL
Low Output Level
–
–
0.75
V
IOL = 25 mA, Vdd = 4.75 to 5.25V
(maximum 100 mA on even port pins
(for example, P0[2], P1[4]), maximum
100 mA on odd port pins (for example,
P0[3], P1[5])). 150 mA maximum
combined IOL budget.
IOH
High Level Source Current
10
–
–
mA
VOH  Vdd-1.0V, see the limitations of
the total current in the note for VOH.
IOL
Low Level Sink Current
25
–
–
mA
VOL  0.75V, see the limitations of the
total current in the note for VOL.
VIL
Input Low Level
–
–
0.8
V
RPU
Pull up Resistor
RPD
VOH
Notes
Note
6. Standby current includes all functions (POR, LVD, WDT, Sleep Timer) needed for reliable system operation. This must be compared with devices that have similar
functions enabled.
Document Number: 38-12029 Rev. *L
Page 16 of 34
CY8C24223A, CY8C24423A
Table 12. DC GPIO Specifications (continued)
Symbol
Description
Min
Typ
Max
Units
–
mV
Notes
VIH
Input High Level
2.1
–
VH
Input Hysterisis
–
60
IIL
Input Leakage (Absolute Value)
–
1
–
nA
Gross tested to 1 A
CIN
Capacitive Load on Pins as Input
–
3.5
10
pF
Package and pin dependent.
Temp = 25C
COUT
Capacitive Load on Pins as Output
–
3.5
10
pF
Package and pin dependent.
Temp = 25C
V
DC Operational Amplifier Specifications
The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C  TA  125°C. Typical parameters apply to 5V at 25°C and are for design guidance only.
The Operational Amplifier is a component of both the Analog Continuous Time (CT) PSoC blocks and the Analog Switched Capacitor
(SC) PSoC blocks. The guaranteed specifications are measured in the Analog Continuous Time (CT) PSoC blocks.
Table 13. DC Operational Amplifier Specifications
Symbol
VOSOA
Description
Input Offset Voltage (absolute value) Low Power
Input Offset Voltage (absolute value) Mid Power
Input Offset Voltage (absolute value) High Power
TCVOSOA Input Offset Voltage Drift
Input Leakage Current (Port 0 Analog Pins)
IEBOA
Input Capacitance (Port 0 Analog Pins)
CINOA
VCMOA
Common Mode Voltage Range
Common Mode Voltage Range (high power or high
opamp bias)
GOLOA
Open Loop Gain
Power = Low
Power = Medium
Power = High
Min
–
–
–
–
–
–
Typ
1.6
1.3
1.2
7.0
200
4.5
0.0
0.5
–
–
–
–
–
80
80
80
VOHIGHOA High Output Voltage Swing (worst case internal load)
Vdd - 0.2
Power = Low
Vdd - 0.2
Power = Medium
Vdd - 0.5
Power = High
VOLOWOA Low Output Voltage Swing (worst case internal load)
Power = Low
–
Power = Medium
–
Power = High
–
ISOA
Supply Current (including associated AGND buffer)
Power = Low, Opamp Bias = Low
–
Power = Low, Opamp Bias = High
–
Power = Medium, Opamp Bias = Low
–
Power = Medium, Opamp Bias = High
–
Power = High, Opamp Bias = Low
–
Power = High, Opamp Bias = High
–
PSRROA Supply Voltage Rejection Ratio
–
Document Number: 38-12029 Rev. *L
Max
11
9
9
35.0
–
9.5
Units
Notes
mV
mV
mV
V/C
pA Gross tested to 1 A
pF
Package and pin
dependent. Temp = 25C.
Vdd
V
The common-mode input
Vdd - 0.5
–
voltage range is
measured through an
analog output buffer. The
specification includes the
limitations imposed by the
characteristics of the
analog output buffer.
Specification is applicable
–
dB at high power. For all other
–
dB bias modes (except high
–
dB power, high opamp bias),
minimum is 60 dB.
–
–
–
–
–
–
V
V
V
–
–
–
0.2
0.2
0.5
V
V
V
150
300
600
1200
2400
4600
80
200
400
800
1600
3200
6400
–
A
A
A
A
A
A
dB
Vss VIN (Vdd - 2.25) or
(Vdd - 1.25V) VIN  Vdd
Page 17 of 34
CY8C24223A, CY8C24423A
DC Low Power Comparator Specifications
The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C  TA  125°C. Typical parameters apply to 5V at 25°C and are for design guidance only.
Table 14. DC Low Power Comparator Specifications
Symbol
VREFLPC
ISLPC
VOSLPC
Description
Low power comparator (LPC) reference voltage range
LPC supply current
LPC voltage offset
Min
0.2
–
–
Typ
–
10
2.5
Max
Vdd - 1
40
30
Units
V
A
mV
Notes
DC Analog Output Buffer Specifications
The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C  TA  125°C. Typical parameters apply to 5V at 25°C and are for design guidance only.
Table 15. DC Analog Output Buffer Specifications
Symbol
VOSOB
TCVOSOB
VCMOB
ROUTOB
VOHIGHOB
Description
Input Offset Voltage (Absolute Value)
Input Offset Voltage Drift
Common-Mode Input Voltage Range
Output Resistance
High Output Voltage Swing (Load = 32 to Vdd/2)
VOLOWOB Low Output Voltage Swing (Load = 32 to Vdd/2)
ISOB
PSRROB
Supply Current Including Bias Cell (No Load)
Power = Low
Power = High
Supply Voltage Rejection Ratio
Document Number: 38-12029 Rev. *L
Min
–
–
0.5
–
0.5 x Vdd
+ 1.1
–
Typ
3
+6
–
1
–
Max
Units
18
mV
–
V/°C
Vdd - 1.0
V
–

–
V
–
0.5 x Vdd
- 1.3
V
–
–
–
1.1
2.6
64
5.1
8.8
–
mA
mA
dB
Notes
Page 18 of 34
CY8C24223A, CY8C24423A
DC Analog Reference Specifications
The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C  TA  125°C. Typical parameters apply to 5V at 25°C and are for design guidance only.
The guaranteed specifications are measured through the Analog Continuous Time PSoC blocks. The power levels for AGND refer to
the power of the Analog Continuous Time PSoC block. The power levels for RefHi and RefLo refer to the Analog Reference Control
register. The limits stated for AGND include the offset error of the AGND buffer local to the Analog Continuous Time PSoC block.
Note Avoid using P2[4] for digital signaling when using an analog resource that depends on the Analog Reference. Some coupling
of the digital signal may appear on the AGND.
Table 16. DC Analog Reference Specifications
Symbol
BG
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Description
Bandgap Voltage Reference
AGND = Vdd/2[7]
AGND = 2 x BandGap[7]
AGND = P2[4] (P2[4] = Vdd/2)[7]
AGND = BandGap[7]
AGND = 1.6 x BandGap[7]
AGND Column to Column Variation (AGND =
Vdd/2)[7]
RefHi = Vdd/2 + BandGap[8]
RefHi = 3 x BandGap[8]
RefHi = 2 x BandGap + P2[6] (P2[6] = 1.3V)[8]
RefHi = P2[4] + BandGap (P2[4] = Vdd/2)[8]
RefHi = P2[4] + P2[6] (P2[4] = Vdd/2, P2[6] =
1.3V)[8]
RefHi = 3.2 x BandGap[8]
RefLo = Vdd/2 – BandGap[8]
RefLo = BandGap[8]
RefLo = 2 x BandGap - P2[6] (P2[6] = 1.3V)[8]
RefLo = P2[4] – BandGap (P2[4] = Vdd/2)[8]
RefLo = P2[4]-P2[6] (P2[4] = Vdd/2, P2[6] = 1.3V)[8]
Min
1.25
Vdd/2 - 0.02
2.4
P2[4] - 0.02
1.23
1.98
-0.035
Typ
1.30
Vdd/2
2.6
P2[4]
1.30
2.08
0.000
Max
1.35
Vdd/2 + 0.02
2.8
P2[4] + 0.02
1.37
2.14
0.035
Units
V
V
V
V
V
V
V
Vdd/2 + 1.15
Vdd/2 +1.30
Vdd/2 +1.45
3.65
P2[6] + 2.4
P2[4] + 1.24
P2[4] + P2[6] - 0.1
3.9
P2[6] + 2.6
P2[4] +1.30
P2[4] + P2[6]
4.15
P2[6] + 2.8
P2[4] + 1.36
P2[4] + P2[6] + 0.1
V
V
V
V
V
4.42
1.15
1.45
2.8 - P2[6]
P2[4] - 1.15
P2[4] - P2[6] + 0.1
V
V
V
V
V
V
3.9
4.16
Vdd/2 - 1.45
Vdd/2 - 1.3
1.15
2.4 - P2[6]
P2[4] - 1.45
P2[4] - P2[6] - 0.1
1.3
2.6 - P2[6]
1.3
P2[4] - P2[6]
Notes
7. This specification is only valid when CT Block Power = High. AGND tolerance includes the offsets of the local buffer in the PSoC block. Bandgap voltage is 1.3V ± 0.05V.
8. This specification is only valid when Ref Control Power = High.
Document Number: 38-12029 Rev. *L
Page 19 of 34
CY8C24223A, CY8C24423A
DC Analog PSoC Block Specifications
The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C  TA  125°C. Typical parameters apply to 5V at 25°C and are for design guidance only.
Table 17. DC Analog PSoC Block Specifications
Symbol
Description
Min
Typ
Max
Units
RCT
Resistor Unit Value (Continuous Time)
–
12.24
–
k
CSC
Capacitor Unit Value (Switch Cap)
–
80
–
fF
Notes
DC POR and LVD Specifications
The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C  TA  125°C. Typical parameters apply to 5V at 25°C and are for design guidance only.
Note The bits PORLEV and VM in the following table refer to bits in the VLT_CR register. See the PSoC Technical Reference Manual
for more information on the VLT_CR register.
Table 18. DC POR and LVD Specifications
Symbol
Description
VPPOR2
Vdd Value for PPOR Trip
PORLEV[1:0] = 10b
VLVD6
VLVD7
Vdd Value for LVD Trip
VM[2:0] = 110b
VM[2:0] = 111b
Min
Typ
Max
Units
–
4.55
4.70
V
4.62
4.710
4.73
4.814
4.83
4.950
V
V
Notes
Vdd must be greater
than or equal to 2.5V
during startup, reset
from the XRES pin, or
reset from watchdog.
DC Programming Specifications
The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C  TA  125°C. Typical parameters apply to 5V at 25°C and are for design guidance only.
Table 19. DC Programming Specifications
Symbol
Description
VddIWRITE Supply Voltage for Flash Write Operations
Min
Typ
Max
Units
4.75
–
–
V
Notes
IDDP
Supply Current During Programming or Verify
–
10
25
mA
VILP
Input Low Voltage During Programming or Verify
–
–
0.8
V
VIHP
Input High Voltage During Programming or Verify
2.1
–
–
V
IILP
Input Current when Applying VILP to P1[0] or P1[1] During
Programming or Verify
–
–
0.2
mA
Driving internal pull
down resistor.
IIHP
Input Current when Applying VIHP to P1[0] or P1[1] During
Programming or Verify
–
–
1.5
mA
Driving internal pull
down resistor.
VOLV
Output Low Voltage During Programming or Verify
–
–
0.75
V
VOHV
Output High Voltage During Programming or Verify
FlashENPB Flash Endurance (per block)[9]
FlashENT
FlashDR
Flash Endurance (total)[9, 10]
Flash Data
Retention[11]
3.5
–
Vdd
V
100
–
–
–
Erase/write cycles per
block.
6,400
–
–
–
Erase/write cycles.
15
–
–
Years
Notes
9. For the full temperature range, the user must employ a temperature sensor user module (FlashTemp) or other temperature sensor, and feed the result to the
temperature argument before writing. Refer to the Flash APIs Application Note AN2015 at http://www.cypress.com under Application Notes for more information.
10. The maximum total number of allowed erase/write cycles is the minimum FlashENPB value multiplied by the number of flash blocks in the device.
11. Flash data retention based on the use condition of  7000 hours at TA  125°C and the remaining time at TA  65°C.
Document Number: 38-12029 Rev. *L
Page 20 of 34
CY8C24223A, CY8C24423A
AC Electrical Characteristics
AC Chip-Level Specifications
The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C  TA  125°C. Typical parameters apply to 5V at 25°C and are for design guidance only.
Table 20. AC Chip-Level Specifications
Symbol
FIMO24
FCPU1
F24M
F32K1
F32KU
Description
Internal Main Oscillator Frequency for
24 MHz
CPU Frequency (5V Vdd Nominal)
Digital PSoC Block Frequency
Internal Low Speed Oscillator
Frequency
Internal Low Speed Oscillator (ILO)
Untrimmed Frequency
Min
23.04[12]
Typ
24
Max
24.96[12]
Units
MHz
0.09[12]
0
15
12
24
32
12.48[12]
24.96[12, 13]
64
MHz
MHz
kHz
5
–
–
kHz
F32K2
External Crystal Oscillator
–
32.768
–
kHz
FPLL
PLL Frequency
–
23.986
–
MHz
Jitter24M2
TPLLSLEW
TPLLSLEWSLOW
TOS
24 MHz Period Jitter (PLL)
PLL Lock Time
PLL Lock Time for Low Gain Setting
External Crystal Oscillator Startup to
1%
External Crystal Oscillator Startup to
100 ppm
32 kHz Period Jitter
External Reset Pulse Width
24 MHz Duty Cycle
Internal Low Speed Oscillator (ILO)
Duty Cycle
24 MHz Trim Step Size
24 MHz Period Jitter (IMO)
Peak-to-Peak
24 MHz Period Jitter (IMO) Root Mean
Squared
Maximum frequency of signal on row
input or row output.
Power Supply Slew Rate
Time between end of POR state and
CPU code execution
–
0.5
0.5
–
–
–
–
1700
800
10
50
2620
ps
ms
ms
ms
–
2800
3800
ms
–
10
40
20
100
–
50
50
–
–
60
80
ns
s
%
%
–
–
50
600
–
–
kHz
ps
–
–
600
ps
–
–
12.48[12]
MHz
–
–
–
16
250
100
V/ms
ms
TOSACC
Jitter32k
TXRST
DC24M
DCILO
Step24M
Jitter24M1P
Jitter24M1R
FMAX
SRPOWERUP
TPOWERUP
Notes
Trimmed using factory trim
values.
This specification applies when
the ILO has been trimmed.
After a reset and before the
M8C processor starts to
execute, the ILO is not trimmed.
Accuracy is capacitor and
crystal dependent. 50% duty
cycle.
A multiple (x732) of crystal
frequency.
Refer to Figure 9 on page 22.
Refer to Figure 6 on page 22.
Refer to Figure 7 on page 22.
Refer to Figure 8 on page 22.
Refer to Figure 10 on page 22.
Refer to Figure 9 on page 22.
Vdd slew rate during power up.
Power up from 0V.
Notes
12. Accuracy derived from Internal Main Oscillator with appropriate trim for Vdd range.
13. See the individual user module data sheets for information on maximum frequencies for user modules.
Document Number: 38-12029 Rev. *L
Page 21 of 34
CY8C24223A, CY8C24423A
Figure 6. PLL Lock Timing Diagram
PLL
Enable
TPLLSLEW
24 MHz
FPLL
PLL
Gain
0
Figure 7. PLL Lock for Low Gain Setting Timing Diagram
PLL
Enable
TPLLSLEWLOW
24 MHz
FPLL
PLL
Gain
1
Figure 8. External Crystal Oscillator Startup Timing Diagram
32K
Select
32 kHz
TOS
F32K2
Figure 9. 24 MHz Period Jitter (IMO) Timing Diagram
Jitter24M1P
Jitter24M2
F 24M
Figure 10. 32 kHz Period Jitter (ECO) Timing Diagram
Jitter32k
F 32K2
Document Number: 38-12029 Rev. *L
Page 22 of 34
CY8C24223A, CY8C24423A
AC General Purpose I/O Specifications
The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C  TA  125°C. Typical parameters apply to 5V at 25°C and are for design guidance only.
Table 21. AC GPIO Specifications
Symbol
FGPIO
TRiseF
TFallF
TRiseS
TFallS
Description
GPIO Operating Frequency
Rise Time, Normal Strong Mode, Cload = 50 pF
Fall Time, Normal Strong Mode, Cload = 50 pF
Rise Time, Slow Strong Mode, Cload = 50 pF
Fall Time, Slow Strong Mode, Cload = 50 pF
Min
0
2
2
9
9
Typ
–
–
–
27
22
Max
12.48[12]
22
22
–
–
Units
MHz
ns
ns
ns
ns
Notes
Normal Strong Mode
10% - 90%
10% - 90%
10% - 90%
10% - 90%
Figure 11. GPIO Timing Diagram
90%
GPIO
Pin
Output
Voltage
10%
TRiseF
TRiseS
TFallF
TFallS
AC Operational Amplifier Specifications
The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C  TA  125°C. Typical parameters apply to 5V at 25°C and are for design guidance only.
Note Settling times, slew rates, and gain bandwidth are based on the Analog Continuous Time PSoC block.
Table 22. AC Operational Amplifier Specifications
Symbol
SRROA
SRFOA
BWOA
Description
Rising Slew Rate (20% to 80%) (10 pF load, Unity Gain)
Power = Low, Opamp Bias = Low
Power = Low, Opamp Bias = High
Power = Medium, Opamp Bias = Low
Power = Medium, Opamp Bias = High
Power = High, Opamp Bias = Low
Power = High, Opamp Bias = High
Falling Slew Rate (80% to 20%) (10 pF load, Unity Gain)
Power = Low, Opamp Bias = Low
Power = Low, Opamp Bias = High
Power = Medium, Opamp Bias = Low
Power = Medium, Opamp Bias = High
Power = High, Opamp Bias = Low
Power = High, Opamp Bias = High
Gain Bandwidth Product
Power = Low, Opamp Bias = Low
Power = Low, Opamp Bias = High
Power = Medium, Opamp Bias = Low
Power = Medium, Opamp Bias = High
Power = High, Opamp Bias = Low
Power = High, Opamp Bias = High
Document Number: 38-12029 Rev. *L
Min
Typ
Max
Units
0.15
0.15
0.15
1.7
1.7
6.5
–
–
–
–
–
–
–
–
–
–
–
–
V/s
V/s
V/s
V/s
V/s
V/s
0.01
0.01
0.01
0.5
0.5
4.0
–
–
–
–
–
–
–
–
–
–
–
–
V/s
V/s
V/s
V/s
V/s
V/s
0.75
0.75
0.75
3.1
3.1
5.4
–
–
–
–
–
–
–
–
–
–
–
–
MHz
MHz
MHz
MHz
MHz
MHz
Page 23 of 34
CY8C24223A, CY8C24423A
AC Low Power Comparator Specifications
The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C  TA  125°C. Typical parameters apply to 5V at 25°C and are for design guidance only.
Table 23. AC Low Power Comparator Specifications
Symbol
TRLPC
Description
LPC response time
Min
–
Typ
–
Max
50
Units
s
Notes
 50 mV overdrive comparator
reference set within VREFLPC.
When bypassed by a capacitor on P2[4], the noise of the analog ground signal distributed to each block is reduced by a factor of up
to 5 (14 dB). This is at frequencies above the corner frequency defined by the on-chip 8.1k resistance and the external capacitor.
Figure 12. Typical AGND Noise with P2[4] Bypass
dBV/rtHz
10000
0
0.01
0.1
1.0
10
1000
100
0.001
0.01
0.1 Freq (kHz)
1
10
100
At low frequencies, the opamp noise is proportional to 1/f, power independent, and determined by device geometry. At high
frequencies, increased power level reduces the noise spectrum level.
Figure 13. Typical Opamp Noise
nV/rtHz
10000
PH_BH
PH_BL
PM_BL
PL_BL
1000
100
10
0.001
Document Number: 38-12029 Rev. *L
0.01
0.1
Freq (kHz)
1
10
100
Page 24 of 34
CY8C24223A, CY8C24423A
AC Digital Block Specifications
The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C  TA  125°C. Typical parameters apply to 5V at 25°C and are for design guidance only.
Table 24. AC Digital Block Specifications
Function
Description
Min
Typ
Max
Units
–
–
24.96[12]
MHz
50[14]
–
–
ns
Maximum Frequency, No Capture
–
–
24.96[12]
MHz
Maximum Frequency, With Capture
–
–
24.96[12]
MHz
Enable Pulse Width
[14]
–
–
ns
All Functions
Maximum Block Clocking Frequency
Timer
Capture Pulse Width
Counter
Dead Band
50
[12]
MHz
Maximum Frequency, No Enable Input
–
–
24.96
Maximum Frequency, Enable Input
–
–
24.96[12]
MHz
Asynchronous Restart Mode
20
–
–
ns
Synchronous Restart Mode
50[14]
–
–
ns
Disable Mode
50[14]
–
–
ns
MHz
Notes
Kill Pulse Width:
Maximum Frequency
–
–
24.96[12]
CRCPRS
(PRS Mode)
Maximum Input Clock Frequency
–
–
24.96[12]
MHz
CRCPRS
(CRC Mode)
Maximum Input Clock Frequency
–
–
24.96[12]
MHz
SPIM
Maximum Input Clock Frequency
–
–
4.16[12]
MHz
SPIS
Maximum Input Clock Frequency
–
–
2.08[12]
MHz
Width of SS_ Negated Between
Transmissions
50[14]
–
–
ns
Transmitter
Maximum Input Clock Frequency
–
–
8.32[12]
MHz
Maximum baud rate is 1.04
Mbaud due to 8 x over clocking.
Receiver
Maximum Input Clock Frequency
–
–
24.96[12]
MHz
Maximum baud rate is 3.12
Mbaud due to 8 x over clocking.
Maximum data rate is 2.08
Mbps due to 2 x over clocking.
Note
14. 50 ns minimum input pulse width is based on the input synchronizers running at 24 MHz (42 ns nominal period).
Document Number: 38-12029 Rev. *L
Page 25 of 34
CY8C24223A, CY8C24423A
AC Analog Output Buffer Specifications
The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C  TA  125°C. Typical parameters apply to 5V at 25°C and are for design guidance only.
Table 25. AC Analog Output Buffer Specifications
Symbol
Description
TROB
Rising Settling Time to 0.1%, 1V Step, 100 pF Load
Power = Low
Power = High
TSOB
Falling Settling Time to 0.1%, 1V Step, 100 pF Load
Power = Low
Power = High
SRROB
Rising Slew Rate (20% to 80%), 1V Step, 100 pF Load
Power = Low
Power = High
SRFOB
Falling Slew Rate (80% to 20%), 1V Step, 100 pF Load
Power = Low
Power = High
BWOB
Small Signal Bandwidth, 20mVpp, 3dB BW, 100 pF Load
Power = Low
Power = High
BWOB
Large Signal Bandwidth, 1Vpp, 3dB BW, 100 pF Load
Power = Low
Power = High
Min
Typ
Max
Units
–
–
–
–
3
3
s
s
–
–
–
–
3
3
s
s
0.6
0.6
–
–
–
–
V/s
V/s
0.6
0.6
–
–
–
–
V/s
V/s
0.8
0.8
–
–
–
–
MHz
MHz
300
300
–
–
–
–
kHz
kHz
AC External Clock Specifications
The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C  TA  125°C. Typical parameters apply to 5V at 25°C and are for design guidance only.
Table 26. AC External Clock Specifications
Min
Typ
Max
Units
FOSCEXT Frequency
Symbol
Description
0.093
–
24.24
MHz
–
High Period
20.6
–
–
ns
–
Low Period
20.6
–
–
ns
–
Power Up IMO to Switch
150
–
–
s
Notes
AC Programming Specifications
The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C  TA  125°C. Typical parameters apply to 5V at 25°C and are for design guidance only.
Table 27. AC Programming Specifications
Symbol
TRSCLK
TFSCLK
TSSCLK
THSCLK
FSCLK
TERASEB
TWRITE
TDSCLK
TPRGH
TPRGC
Description
Rise Time of SCLK
Fall Time of SCLK
Data Set up Time to Falling Edge of SCLK
Data Hold Time from Falling Edge of SCLK
Frequency of SCLK
Flash Erase Time (Block)
Flash Block Write Time
Data Out Delay from Falling Edge of SCLK
Total Flash Block Program Time (TERASEB
+ TWRITE), Hot
Total Flash Block Program Time (TERASEB
+ TWRITE), Cold
Document Number: 38-12029 Rev. *L
Min
1
1
40
40
0
–
–
–
–
Typ
–
–
–
–
–
20
80
–
–
Max
20
20
–
–
8
80[9]
320[9]
50
200[9]
Units
ns
ns
ns
ns
MHz
ms
ms
ns
ms
Notes
TJ  0°C
–
–
400[9]
ms
TJ  0°C
Page 26 of 34
CY8C24223A, CY8C24423A
AC I2C Specifications
The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C  TA  125°C. Typical parameters apply to 5V at 25°C and are for design guidance only.
Table 28. AC Characteristics of the I2C SDA and SCL Pins
Symbol
Description
FSCLI2C
THDSTAI2C
SCL Clock Frequency
Hold Time (repeated) START Condition. After this period, the first
clock pulse is generated.
LOW Period of the SCL Clock
HIGH Period of the SCL Clock
Setup Time for a Repeated START Condition
Data Hold Time
Data Setup Time
Setup Time for STOP Condition
Bus Free Time Between a STOP and START Condition
Pulse Width of spikes are suppressed by the input filter.
TLOWI2C
THIGHI2C
TSUSTAI2C
THDDATI2C
TSUDATI2C
TSUSTOI2C
TBUFI2C
TSPI2C
Standard Mode
Min
Max
0
100[15]
4.0
–
4.7
4.0
4.7
0
250
4.0
4.7
–
Fast Mode
Min
Max
0
400[15]
0.6
–
–
–
–
–
–
–
–
–
1.3
0.6
0.6
0
100[16]
0.6
1.3
0
–
–
–
–
–
–
–
50
Units
kHz
s
s
s
s
s
ns
s
s
ns
Figure 14. Definition for Timing for Fast/Standard Mode on the I2C Bus
SDA
TLOWI2C
TSUDATI2C
THDSTAI2C
TSPI2C
TBUFI2C
SCL
S THDSTAI2C THDDATI2C THIGHI2C
TSUSTAI2C
Sr
TSUSTOI2C
P
S
Notes
15. FSCLI2C is derived from SysClk of the PSoC. This specification assumes that SysClk is operating at 24 MHz, nominal. If SysClk is at a lower frequency, then the FSCLI2C
specification adjusts accordingly.
16. A Fast-Mode I2C-bus device can be used in a Standard-Mode I2C-bus system, but the requirement TSUDATI2C  250 ns must then be met. This is automatically the case
if the device does not stretch the LOW period of the SCL signal. If such device does stretch the LOW period of the SCL signal, it must output the next data bit to the
SDA line trmax + TSUDATI2C = 1000 + 250 = 1250 ns (according to the Standard-Mode I2C-bus specification) before the SCL line is released.
Document Number: 38-12029 Rev. *L
Page 27 of 34
CY8C24223A, CY8C24423A
Packaging Information
This section illustrates the packaging specifications for the automotive CY8C24x23A PSoC device, along with the thermal impedances
for each package and the typical package capacitance on crystal pins.
Important Note Emulation tools may require a larger area on the target PCB than the chip’s footprint. For a detailed description of
the emulation tools’ dimensions, refer to the emulator pod drawings at http://www.cypress.com.
Figure 15. 20-Pin (210-Mil) SSOP
51-85077 *E
Document Number: 38-12029 Rev. *L
Page 28 of 34
CY8C24223A, CY8C24423A
Figure 16. 28-Pin (210-Mil) SSOP
51-85079 *E
Thermal Impedances
Capacitance on Crystal Pins
Typical JA [17]
Package
Package
Package Capacitance
20 SSOP
117 C/W
20 SSOP
2.6 pF
28 SSOP
101 C/W
28 SSOP
2.8 pF
Solder Reflow Specifications
The following table shows the solder reflow temperature limits that must not be exceeded.
Package
Maximum Time above TC – 5 °C
Maximum Peak Temperature
20 SSOP
30 seconds
260C
28 SSOP
30 seconds
260C
Note
17. TJ = TA + POWER x JA
Document Number: 38-12029 Rev. *L
Page 29 of 34
CY8C24223A, CY8C24423A
Development Tool Selection
This section presents the development tools available for the CY8C24x23A family.
Software
Evaluation Tools
PSoC Designer
All evaluation tools can be purchased from the Cypress Online
Store. The online store also has the most up to date information
on kit contents, descriptions, and availability.
At the core of the PSoC development software suite is PSoC
Designer. Utilized by thousands of PSoC developers, this robust
software has been facilitating PSoC designs for years. PSoC
Designer is available free of charge at http://www.cypress.com.
PSoC Designer comes with a free C compiler.
PSoC Programmer
Flexible enough to be used on the bench in development, yet
suitable for factory programming, PSoC Programmer works
either as a standalone programming application or it can operate
directly from PSoC Designer. PSoC Programmer software is
compatible with both PSoC ICE-Cube In-Circuit Emulator and
PSoC MiniProg. PSoC programmer is available free of charge at
http://www.cypress.com.
Development Kits
All development kits can be purchased from the Cypress Online
Store. The online store also has the most up to date information
on kit contents, descriptions, and availability.
CY3215-DK Basic Development Kit
The CY3215-DK is for prototyping and development with PSoC
Designer. This kit supports in-circuit emulation and the software
interface allows users to run, halt, and single step the processor
and view the contents of specific memory locations. Advanced
emulation features are also supported through PSoC Designer.
The kit includes:
■
ICE-Cube Unit
■
28-Pin PDIP Emulation Pod for CY8C29466-24PXI
■
28-Pin CY8C29466-24PXI PDIP PSoC Device Samples (two)
■
PSoC Designer Software CD
■
ISSP Cable
■
MiniEval Socket Programming and Evaluation board
■
Backward Compatibility Cable (for connecting to legacy Pods)
■
Universal 110/220 Power Supply (12V)
■
European Plug Adapter
■
USB 2.0 Cable
■
Getting Started Guide
■
Development Kit Registration form
Document Number: 38-12029 Rev. *L
CY3210-PSoCEval1
The CY3210-PSoCEval1 kit features an evaluation board and
the MiniProg1 programming unit. The evaluation board includes
an LCD module, potentiometer, LEDs, an RS-232 port, and
plenty of breadboarding space to meet all of your evaluation
needs. The kit includes:
■
Evaluation Board with LCD Module
■
MiniProg Programming Unit
■
28-Pin CY8C29466-24PXI PDIP PSoC Device Sample (2)
■
PSoC Designer Software CD
■
Getting Started Guide
■
USB 2.0 Cable
CY3210-24X23 Evaluation Pod (EvalPod)
PSoC EvalPods are pods that connect to the ICE In-Circuit
Emulator (CY3215-DK kit) to allow debugging capability. They
can also function as a standalone device without debugging
capability. The EvalPod has a 28-pin DIP footprint on the bottom
for easy connection to development kits or other hardware. The
top of the EvalPod has prototyping headers for easy connection
to the device's pins. CY3210-24X23 provides evaluation of the
CY8C24x23A PSoC device family.
Page 30 of 34
CY8C24223A, CY8C24423A
Device Programmers
CY3207ISSP In-System Serial Programmer (ISSP)
All device programmers can be purchased from the Cypress
Online Store.
The CY3207ISSP is a production programmer. It includes
protection circuitry and an industrial case that is more robust than
the MiniProg in a production-programming environment.
CY3210-MiniProg1
The CY3210-MiniProg1 kit allows a user to program PSoC
devices via the MiniProg1 programming unit. The MiniProg is a
small, compact prototyping programmer that connects to the PC
via a provided USB 2.0 cable. The kit includes:
■
MiniProg Programming Unit
■
MiniEval Socket Programming and Evaluation Board
■
28-Pin CY8C29466-24PXI PDIP PSoC Device Sample
■
PSoC Designer Software CD
■
Getting Started Guide
■
USB 2.0 Cable
Note: CY3207ISSP needs special software and is not
compatible with PSoC Programmer. This software is free and
can be downloaded from http://www.cypress.com. The kit
includes:
■
CY3207 Programmer Unit
■
PSoC ISSP Software CD
■
110 ~ 240V Power Supply, Euro-Plug Adapter
■
USB 2.0 Cable
Accessories (Emulation and Programming)
Table 29. Emulation and Programming Accessories
Part Number
Pin Package
Pod Kit[18]
Foot Kit[19]
CY8C24223A-12PVXE
20 SSOP
CY3250-24X23A
CY3250-20SSOP-FK
CY8C24423A-12PVXE
28 SSOP
CY3250-24X23A
CY3250-28SSOP-FK
Adapter[20]
Adapters can be found at
http://www.emulation.com.
Notes
18. Pod kit contains an emulation pod, a flex-cable (connects the pod to the ICE), two feet, and device samples.
19. Foot kit includes surface mount feet that can be soldered to the target PCB.
20. Programming adapter converts non-DIP package to DIP footprint. Specific details and ordering information for each of the adapters can be found at
http://www.emulation.com.
Document Number: 38-12029 Rev. *L
Page 31 of 34
CY8C24223A, CY8C24423A
Ordering Information
Flash
(Bytes)
RAM
(Bytes)
Switch Mode
Pump
Temperature
Range
Digital Blocks
Analog Blocks
Digital I/O Pins
Analog Inputs
Analog Outputs
XRES Pin
CY8C24223A-12PVXE
CY8C24223A-12PVXET
4K
4K
256
256
No
No
-40°C to +125°C
-40°C to +125°C
4
4
6
6
16
16
8
8
2
2
Yes
Yes
CY8C24423A-12PVXE
CY8C24423A-12PVXET
4K
4K
256
256
No
No
-40°C to +125°C
-40°C to +125°C
4
4
6
6
24
24
12[1]
12[1]
2
2
Yes
Yes
Package
Ordering
Code
The following table lists the automotive CY8C24x23A PSoC device group’s key package features and ordering codes.
20 Pin (210 Mil) SSOP
20 Pin (210 Mil) SSOP
(Tape and Reel)
28 Pin (210 Mil) SSOP
28 Pin (210 Mil) SSOP
(Tape and Reel)
Ordering Code Definitions
CY 8 C 24 xxx-12xx
Package Type:
Thermal Rating:
PX = PDIP Pb-free
A = Automotive -40°C to +85°C
SX = SOIC Pb-free
C = Commercial
PVX = SSOP Pb-free
I = Industrial
LFX/LKX = QFN Pb-free
E = Automotive Extended -40°C to +125°C
AX = TQFP Pb-free
CPU Speed: 12 MHz
Part Number
Family Code
Technology Code: C = CMOS
Marketing Code: 8 = PSoC
Company ID: CY = Cypress
Document Number: 38-12029 Rev. *L
Page 32 of 34
CY8C24223A, CY8C24423A
Document History Page
Document Title: CY8C24223A, CY8C24423A Automotive - Extended Temperature PSoC® Programmable System-on-Chip
Document Number: 38-12029
Orig. of
Submission
Rev.
ECN
Description of Change
Change
Date
238268
SFV
See ECN
First release of CY8C24x23A Automotive Preliminary Data Sheet.
**
271471
HMT
See ECN
Update per SFV memo. Input MWR changes, including removing SMP. Change
*A
to Final.
*B
286089
HMT
See ECN
Update characterization data. Fine tune pinouts. Add Reflow Peak Temp. table.
512475
HMT
See ECN
Add Low Power Comparator (LPC) AC/DC electrical spec. tables. Add ISSP note
*C
to pinout tables. Update typical and recommended Storage Temperature per
extended temp. specs. Update CY branding and QFN convention. Update
copyright and trademarks.
*D
2101387
AESA
See ECN
Post to www.cypress.com
*E
2619935 OGNE/AESA
12/11/2008 Changed title to “CY8C24223A, CY8C24423A PSoC® Programmable
System-on-Chip™”
Added note on digital signaling in DC Analog Reference Specifications on page
19.
Added Die Sales information note to Ordering Information on page 32.
Updated data sheet template.
*F
2659314 PRKA/PYRS
02/13/09
Changed title to “Automotive - Extended Temperature CY8C24223A,
CY8C24423A PSoC® Programmable System-on-Chip™”
Updated Development Tools and Designing with PSoC Designer sections on
pages 5 and 6.
*G
2719510
BTK
06/16/09
Changed title. Updated Features section. Updated text of PSoC Functional
Overview section. Updated Getting Started section. Made corrections and minor
text edits to Pinouts section. Changed the name of the Register Reference
section to “Registers”. Improved formatting of the register tables. Added clarifying
comments to some electrical specifications. Changed TRAMP specification per
MASJ input. Changed number of analog inputs for 28-pin package to 12 from 10.
Fixed all AC specifications to conform to a ±4% IMO accuracy. Made other
miscellaneous minor text edits. Deleted some non-applicable or redundant
information. Added a footnote to clarify that 8 of the 12 analog inputs are regular
and the other 4 are direct SC block connections. Added Development Tool
Selection section.
*H
2822792 BTK/AESA
12/07/2009 Added TPRGH, TPRGC, IOL, IOH, F32KU, DCILO, and TPOWERUP electrical
specifications. Updated the text of footnote 10. Added maximum values and
updated typical values for TERASEB and TWRITE electrical specifications.
Replaced TRAMP electrical specification with SRPOWERUP electrical specification.
Added “Contents” on page 2. This revision fixes CDT 63984.
*I
2888007
NJF
03/30/2010 Updated Cypress website links.
Updated PSoC Designer Software Subsystems.
Added TBAKETEMP and TBAKETIME parameters in Absolute Maximum Ratings.
Updated links in Sales, Solutions, and Legal Information.
Removed Third Party Tools and Build a PSoC Emulator into your Board.
*J
3184892 PRKA/VIVG
03/01/2011 No change. Sunset review spec.
*K
3726340 08/28/2012
tess_ukr/
Updated the following sections: Getting Started, Development Tools, and
LURE
Designing with PSoC Designer as all the System level designs have been
de-emphasized.
Changed the PWM description string from “8- to 32-bit” to “8- and 16-bit”.
Updated package diagrams.
Updated solder reflow specifications.
*L
4304787 03/11/2014
JICG
Updated in new template.
Completing Sunset Review.
Document Number: 38-12029 Rev. *L
Page 33 of 34
CY8C24223A, CY8C24423A
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at Cypress Locations.
PSoC® Solutions
Products
Automotive
Clocks & Buffers
Interface
Lighting & Power Control
cypress.com/go/automotive
cypress.com/go/clocks
cypress.com/go/interface
cypress.com/go/powerpsoc
cypress.com/go/plc
Memory
cypress.com/go/memory
PSoC
cypress.com/go/psoc
Touch Sensing
PSoC 1 | PSoC 3 | PSoC 4 | PSoC 5LP
Cypress Developer Community
Community | Forums | Blogs | Video | Training
Technical Support
cypress.com/go/support
cypress.com/go/touch
USB Controllers
Wireless/RF
psoc.cypress.com/solutions
cypress.com/go/USB
cypress.com/go/wireless
© Cypress Semiconductor Corporation, 2004-2014. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of
any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for
medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as
critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems
application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Document Number: 38-12029 Rev. *L
Revised March 11, 2014
Page 34 of 34
PSoC Designer™ and Programmable System-on-Chip™ are trademarks and PSoC® and CapSense® are registered trademarks of Cypress Semiconductor Corporation.
Purchase of I2C components from Cypress or one of its sublicensed Associated Companies conveys a license under the Philips I2C Patent Rights to use these components in an I2C system, provided
that the system conforms to the I2C Standard Specification as defined by Philips. As from October 1st, 2006 Philips Semiconductors has a new trade name - NXP Semiconductors.
All products and company names mentioned in this document may be the trademarks of their respective holders.