CY8C21345, CY8C22345, CY8C22545 PSoC Programmable System-on-Chip Datasheet.pdf

CY8C21345
CY8C22345
CY8C22545
PSoC® Programmable System-on-Chip
Features
■
■
■
Powerful Harvard-architecture processor:
❐ M8C processor speeds up to 24 MHz
❐ 8 × 8 multiply, 32-bit accumulate
❐ Low power at high speed
❐ 3.0 V to 5.25 V operating voltage
❐ Industrial temperature range: –40 °C to +85 °C
Advanced peripherals (PSoC® Blocks)
❐ Six analog type “E” PSoC blocks provide:
• Single or dual 8-Bit ADC
• Comparators (up to four)
❐ Up to eight digital PSoC blocks provide:
• 8- to 32-bit timers and counters, 8- and 16-bit pulse-width
modulators (PWMs)
• One shot, multi-shot mode support in timers and PWMs
• PWM with deadband support in one digital block
• Shift register, CRC, and PRS modules
• Full duplex UART
• Multiple SPI masters or slaves, variable data length
Support: 8- to 16-Bit
• Can be connected to all GPIO pins
❐ Complex peripherals by combining blocks
❐ Shift function support for FSK detection
❐ Powerful synchronize feature support. Analog module
operations can be synchronized by digital blocks or external
signals.
• CSD_CLK: 1/2/4/8/16/32/128/256 derive from SYSCLK
• CNT_CLK: 1/2/4/8 Derive from CSD_CLK
❐ Dedicated 16-bit timers/counters for CapSense scanning
❐ Support dual CSD channels simultaneous scanning
■
Programmable pin configurations:
❐ 25 mA sink, 10 mA source on all GPIOs
❐ Pull-up, pull-down, high Z, Strong, or open-drain drive modes
on all GPIOs
❐ Up to 38 analog inputs on GPIOs
❐ Configurable interrupt on all GPIOs
■
Additional system resources:
2
❐ I C slave, master, and multimaster to 400 kHz
❐ Supports hardware addressing feature
❐ Watchdog and sleep timers
❐ User configurable low voltage detection
❐ Integrated supervisory circuit
❐ On-Chip precision voltage reference
❐ Supports RTC block into digital peripheral logic
Top Level Block Diagram
Port 4
Global Digital Interconnect
SRAM
1K
High speed 10-bit SAR ADC with sample and hold optimized for
■
SROM
Analog
Drivers
Precision, programmable clocking:
[1] 24/48 MHz oscillator across the industrial
❐ Internal ± 5%
temperature range
❐ High accuracy 24 MHz with optional 32 kHz crystal and PLL
❐ Optional external oscillator, up to 24 MHz
❐ Internal/external oscillator for watchdog and sleep
Global Analog Interconnect
Flash 16K
CPU Core (M8C)
Interrupt
Controller
Sleep and
Watchdog
Multiple Clock Sources
(Includes IMO, ILO, PLL, and ECO)
ANALOG SYSTEM
DIGITAL SYSTEM
Digital Block Array
Analog
Ref
Analog Input
Muxing(L,R)
DBC DBC DCC DCC
=
ROW 1
Flexible on-chip memory:
❐ Up to 16 KB flash program storage 50,000 erase/write cycles
❐ Up to 1-KB SRAM data storage
❐ In-system serial programming (ISSP)
❐ Partial flash updates
❐ Flexible protection modes
❐ EEPROM emulation in flash
Analog Block Array
DBC DBC DCC DCC
ROW 2
System Bus
■
Port 2 Port 1 Port 0
PSoC Core
embedded control
■
Port 3
Optimized CapSense® resource:
❐ Two IDAC support up to 640 µA source current to replace
external resistor
❐ Two dedicated clock resources for CapSense:
CapSense
Digital Resource
Digital
Clocks
MACs
CTE
CTE
SCE
SCE
CTE
CTE
10-bit SAR
ADC
I2C
POR and LVD
System Resets
Internal
Voltage
Ref.
SYSTEM RESOURCES
Errata: For information on silicon errata, see “Errata” on page 35. Details include trigger conditions, devices affected, and proposed workaround.
Note
1. Errata: When the device is operated within 0 °C to 70 °C, the frequency tolerance is reduced to ±2.5%, but if operated at extreme temperature (below 0 °C or above
70 °C), frequency tolerance deviates from ±2.5% to ±5%. For more information, see “Errata” on page 35.
Cypress Semiconductor Corporation
Document Number: 001-43084 Rev. *V
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised December 17, 2014
CY8C21345
CY8C22345
CY8C22545
Contents
PSoC Functional Overview .............................................. 3
PSoC Core .................................................................. 3
Digital System ............................................................. 3
Analog System ............................................................ 4
Additional System Resources ..................................... 4
PSoC Device Characteristics ...................................... 5
Getting Started .................................................................. 5
Application Notes ........................................................ 5
Development Kits ........................................................ 5
Training ....................................................................... 5
CYPros Consultants .................................................... 5
Solutions Library .......................................................... 5
Technical Support ....................................................... 5
Development Tools .......................................................... 6
PSoC Designer Software Subsystems ........................ 6
Designing with PSoC Designer ....................................... 7
Select User Modules ................................................... 7
Configure User Modules .............................................. 7
Organize and Connect ................................................ 7
Generate, Verify, and Debug ....................................... 7
Pinouts .............................................................................. 8
CY8C22345, CY8C21345 28-pin SOIC ...................... 8
CY8C22545 44-pin TQFP ........................................... 9
Registers ......................................................................... 10
Register Conventions ................................................ 10
Register Mapping Tables .......................................... 10
Document Number: 001-43084 Rev. *V
Electrical Specifications ................................................ 13
Absolute Maximum Ratings ....................................... 14
Operating Temperature ............................................. 14
DC Electrical Characteristics ..................................... 15
AC Electrical Characteristics ..................................... 21
Packaging Information ................................................... 27
Thermal Impedances ................................................. 28
Solder Reflow Specifications ..................................... 28
Ordering Information ...................................................... 28
Ordering Code Definitions ......................................... 28
Acronyms ........................................................................ 29
Reference Documents .................................................... 29
Document Conventions ................................................. 30
Units of Measure ....................................................... 30
Numeric Conventions .................................................... 30
Glossary .......................................................................... 30
Errata ............................................................................... 35
Part Numbers Affected .............................................. 35
CY8C21x45, CY8C22x45 Qualification Status .......... 35
Errata Summary ........................................................ 35
Document History Page ................................................. 37
Sales, Solutions, and Legal Information ...................... 40
Worldwide Sales and Design Support ....................... 40
Products .................................................................... 40
PSoC® Solutions ...................................................... 40
Cypress Developer Community ................................. 40
Technical Support ..................................................... 40
Page 2 of 40
CY8C21345
CY8C22345
CY8C22545
PSoC Functional Overview
The PSoC family consists of many On-Chip Controller devices.
These devices are designed to replace multiple traditional
MCU-based system components with one low cost single-chip
programmable device. PSoC devices include configurable
blocks of analog and digital logic, and programmable
interconnects. This architecture enables the user to create
customized peripheral configurations that match the
requirements of each individual application. Additionally, a fast
CPU, Flash program memory, SRAM data memory, and
configurable I/O are included in a range of convenient pinouts
and packages.
Digital System
The Digital System is composed of eight digital PSoC blocks.
Each block is an 8-bit resource that may be used alone or
combined with other blocks to form 8, 16, 24, and 32-bit
peripherals, which are called user module references.
Figure 1. Digital System Block Diagram
Port 3
Port 2
To System Bus
Digital Clocks
From Core
The PSoC architecture, shown in Figure 1, consists of four main
areas: PSoC Core, Digital System, Analog System, and System
Resources. Configurable global busing allows the combining of
all the device resources into a complete custom system. The
PSoC family can have up to five I/O ports connecting to the
global digital and analog interconnects, providing access to eight
digital blocks and six analog blocks.
Port 0
To Analog
System
DIGITAL SYSTEM
Row 0
DBC00
DBC01
DCC02
4
DCC03
4
Row Output
Configuration
Row Input
Configuration
Digital PSoC Block Array
8
8
PSoC Core
8
Row Input
Configuration
8
The M8C CPU core is a powerful processor with speeds up to
24 MHz, providing a four MIPS 8-bit Harvard architecture
microprocessor. The CPU uses an interrupt controller with 21
vectors, to simplify the programming of real time embedded
events.
Row 1
DBC00
GIE[7:0]
GIO[7:0]
Program execution is timed and protected using the included
Sleep and watchdog timers (WDT).
DBC01
DCC02
DCC03
Global Digital
Interconnect
Row Output
Configuration
The PSoC Core is a powerful engine that supports a rich feature
set. The core includes a CPU, memory, clocks, and configurable
general-purpose I/O (GPIO).
Memory encompasses 16 KB of Flash for program storage, 1 K
bytes of SRAM for data storage, and up to 2 KB of EEPROM
emulated using the Flash. Program Flash uses four protection
levels on blocks of 64 bytes, allowing customized software IP
protection.
Port 1
Port 4
GOE[7:0]
GOO[7:0]
Digital peripheral configurations are:
■
PWMs (8- and 16-Bit)
■
PWMs with Dead band (8- and 16-Bit)
The PSoC device incorporates flexible internal clock generators,
including a 24 MHz IMO (internal main oscillator). The 24 MHz
IMO can also be doubled to 48 MHz for use by the digital system.
A low power 32 kHz internal low-speed oscillator (ILO) is
provided for the Sleep timer and WDT. If crystal accuracy is
required, the ECO (32.768 kHz external crystal oscillator) is
available for use as a Real Time Clock (RTC), and can optionally
generate a crystal-accurate 24 MHz system clock using a PLL.
The clocks, together with programmable clock dividers (as a
System Resource), provide the flexibility to integrate almost any
timing requirement into the PSoC device.
■
Counters (8 to 32-Bit)
■
Timers (8 to 32-Bit)
■
UART 8 Bit with Selectable Parity (Up to Two)
■
SPI Master and Slave (Up to Two)
■
Shift Register (1 to 32-Bit)
■
I2C Slave and Master (One Available as a System Resource)
■
Cyclical Redundancy Checker/Generator (8 to 32-Bit)
PSoC GPIOs provide connection to the CPU, digital, and analog
resources of the device. Each pin’s drive mode may be selected
from eight options, allowing great flexibility in external
interfacing. Every pin can also generate a system interrupt on
high level, low level, and change from last read.
■
IrDA (Up to Two)
■
Pseudo Random Sequence Generators (8 to 32-Bit)
The digital blocks may be connected to any GPIO through a
series of global buses that can route any signal to any pin. The
buses also allow for signal multiplexing and performing logic
operations. This configurability frees your designs from the
constraints of a fixed peripheral controller.
Digital blocks are provided in rows of four, where the number of
blocks varies by PSoC device family. This provides a choice of
system resources for your application. Family resources are
shown in Table 1 on page 5.
Document Number: 001-43084 Rev. *V
Page 3 of 40
CY8C21345
CY8C22345
CY8C22545
Analog System
Additional System Resources
The Analog System consists of a 10-bit SAR ADC and six
configurable blocks.
System Resources, some of which are listed in the previous
sections, provide additional capability useful to complete
systems. Additional resources include a MAC, low voltage
detection, and power on reset. The merits of each system
resource are:
The programmable 10-bit SAR ADC is an optimized ADC that
can be run up to 200 ksps with ± 1.5 LSB DNL and ± 2.5 LSB INL
(true for VDD  3.0 V and Vref  3.0 V). External filters are
required on ADC input channels for antialiasing. This ensures
that any out-of-band content is not folded into the input signal
band.
Reconfigurable analog resources allow creating complex analog
signal flows. Analog peripherals are very flexible and may be
customized to support specific application requirements. Some
of the more common PSoC analog functions (most available as
user modules) are:
■
Analog-to-Digital converters (Single or Dual, with 8-bit
resolution)
■
Pin-to-pin Comparator
■
Single ended comparators with absolute (1.3 V) reference or
5-bit DAC reference
■
1.3 V reference (as a System Resource)
Analog blocks are provided in columns of four, which include
CT-E (Continuous Time) and SC-E (Switched Capacitor) blocks.
These devices provide limited functionality Type “E” analog
blocks.
■
Digital clock dividers provide three customizable clock
frequencies for use in applications. The clocks may be routed
to both the digital and analog systems. Additional clocks can
be generated using digital PSoC blocks as clock dividers.
■
Additional Digital resources and clocks optimized for CSD.
■
Support “RTC” block into digital peripheral logic.
■
A multiply accumulate (MAC) provides a fast 8-bit multiplier
with 32-bit accumulate, to assist in both general math and
digital filters.
■
The I2C module provides 100 and 400 kHz communication over
two wires. Slave, master, and multi-master modes are all
supported.
■
Low Voltage Detection (LVD) interrupts can signal the
application of falling voltage levels, while the advanced POR
(Power On Reset) circuit eliminates the need for a system
supervisor.
■
An internal 1.3 V reference provides an absolute reference for
the analog system, including ADCs and DACs.
Figure 2. Analog System Block Diagram
Array Input Configuration
ACI0[1:0]
ACI1[1:0]
ACI1[1:0]
ACI1[1:0]
ACE00
ACE01
ACE10
ACE11
ASE10
ASE11
Block Array
AmuxL
AmuxR
P0[0:7]
ACI2[3:0]
10 bit SAR ADC
Analog Reference
Interface to
Digital System
AGND
Reference
Generators
Bandgap
M8C Interface (Address Bus, Data Bus, Etc.)
Document Number: 001-43084 Rev. *V
Page 4 of 40
CY8C21345
CY8C22345
CY8C22545
PSoC Device Characteristics
Depending on your PSoC device characteristics, the digital and analog systems can have 16, 8, or 4 digital blocks and 12, 6, or 3
analog blocks. The following table lists the resources available for specific PSoC device groups.
Table 1. PSoC Device Characteristics
PSoC Part
Number
Digital
I/O
Digital
Rows
Digital
Blocks
Analog
Inputs
Analog
Outputs
Analog
Columns
Analog
Blocks
SRAM
Size
Flash
Size
CY8C29x66[2]
up to 64
4
16
up to 12
4
4
12
2K
32 K
CY8C28xxx
up to 44
up to 3
up to 12
up to 44
up to 4
up to 6
up to
12 + 4[3]
1K
16 K
CY8C27x43
up to 44
2
8
up to 12
4
4
12
256
16 K
CY8C24x94[2]
up to 56
1
4
up to 48
2
2
6
1K
16 K
CY8C24x23A
[2]
up to 24
1
4
up to 12
2
2
6
256
4K
CY8C23x33
up to 26
1
4
up to 12
2
2
4
256
8K
CY8C22x45[2]
up to 38
2
8
up to 38
0
4
6[3]
1K
16 K
[2]
up to 24
1
4
up to 24
0
4
6[3]
512
8K
CY8C21x34[2]
up to 28
1
4
up to 28
0
2
4[3]
512
8K
[3]
256
4K
CY8C21x45
CY8C21x23
up to 16
1
4
up to 8
0
2
CY8C20x34[2]
up to 28
0
0
up to 28
0
0
3[3,4]
4
512
8K
CY8C20xx6
up to 36
0
0
up to 36
0
0
3[3,4]
up to 2 K
up to 32 K
Getting Started
For in-depth information, along with detailed programming
details, see the CY8C22x45, CY8C21345: PSoC®
Programmable System-on-Chip™ Technical Reference Manual.
Training
For up-to-date ordering, packaging, and electrical specification
information, see the latest PSoC device datasheets on the web.
Free PSoC technical training (on demand, webinars, and
workshops), which is available online via www.cypress.com,
covers a wide variety of topics and skill levels to assist you in
your designs.
Application Notes
CYPros Consultants
Cypress application notes are an excellent introduction to the
wide variety of possible PSoC designs. Use PSoC 1 Application
note finder to search application notes or example projects for a
specific application and/or family.
Certified PSoC consultants offer everything from technical
assistance to completed PSoC designs. To contact or become a
PSoC consultant go to the CYPros Consultants web site.
Development Kits
PSoC 1 kits are available online from Cypress and also available
through a growing number of regional and global distributors,
which include Arrow, Avnet, Digi-Key, Farnell, Future
Electronics, and Newark. The kit selector guide available in
cypress website offers the list of all available development kits,
programming and debugging kits for each PSoC 1 family.
Solutions Library
Visit our growing library of solution focused designs. Here you
can find various application designs that include firmware and
hardware design files that enable you to complete your designs
quickly.
Technical Support
Technical support – including a searchable Knowledge Base
articles and technical forums – is also available online. If you
cannot find an answer to your question, call our Technical
Support hotline at 1-800-541-4736.
Notes
2. Automotive qualified devices available in this group.
3. Limited analog functionality.
4. Two analog blocks and one CapSense® block.
Document Number: 001-43084 Rev. *V
Page 5 of 40
CY8C21345
CY8C22345
CY8C22545
Development Tools
PSoC Designer™ is the revolutionary integrated design
environment (IDE) that you can use to customize PSoC to meet
your specific application requirements. PSoC Designer software
accelerates system design and time to market. Develop your
applications using a library of precharacterized analog and digital
peripherals (called user modules) in a drag-and-drop design
environment. Then, customize your design by leveraging the
dynamically generated application programming interface (API)
libraries of code. Finally, debug and test your designs with the
integrated debug environment, including in-circuit emulation and
standard software debug features. PSoC Designer includes:
■
Application editor graphical user interface (GUI) for device and
user module configuration and dynamic reconfiguration
■
Extensive user module catalog
■
Integrated source-code editor (C and assembly)
■
Free C compiler with no size restrictions or time limits
■
Built-in debugger
■
In-circuit emulation
■
Built-in support for communication interfaces:
2
❐ Hardware and software I C slaves and masters
❐ Full-speed USB 2.0
❐ Up
to
four
full-duplex
universal
asynchronous
receiver/transmitters (UARTs), SPI master and slave, and
wireless
PSoC Designer supports the entire library of PSoC 1 devices and
runs on Windows XP, Windows Vista, and Windows 7.
PSoC Designer Software Subsystems
Design Entry
In the chip-level view, choose a base device to work with. Then
select different onboard analog and digital components that use
the PSoC blocks, which are called user modules. Examples of
user modules are ADCs, DACs, amplifiers, and filters. Configure
the user modules for your chosen application and connect them
to each other and to the proper pins. Then generate your project.
This prepopulates your project with APIs and libraries that you
can use to program your application.
The tool also supports easy development of multiple
configurations and dynamic reconfiguration. Dynamic
reconfiguration makes it possible to change configurations at run
Document Number: 001-43084 Rev. *V
time. In essence, this allows you to use more than 100 percent
of PSoC's resources for an application.
Code Generation Tools
The code generation tools work seamlessly within the
PSoC Designer interface and have been tested with a full range
of debugging tools. You can develop your design in C, assembly,
or a combination of the two.
Assemblers. The assemblers allow you to merge assembly
code seamlessly with C code. Link libraries automatically use
absolute addressing or are compiled in relative mode, and are
linked with other software modules to get absolute addressing.
C Language Compilers. C language compilers are available
that support the PSoC family of devices. The products allow you
to create complete C programs for the PSoC family devices. The
optimizing C compilers provide all of the features of C, tailored
to the PSoC architecture. They come complete with embedded
libraries providing port and bus operations, standard keypad and
display support, and extended math functionality.
Debugger
PSoC Designer has a debug environment that provides
hardware in-circuit emulation, allowing you to test the program in
a physical system while providing an internal view of the PSoC
device. Debugger commands allow you to read and program and
read and write data memory, and read and write I/O registers.
You can read and write CPU registers, set and clear breakpoints,
and provide program run, halt, and step control. The debugger
also allows you to create a trace buffer of registers and memory
locations of interest.
Online Help System
The online help system displays online, context-sensitive help.
Designed for procedural and quick reference, each functional
subsystem has its own context-sensitive help. This system also
provides tutorials and links to FAQs and an online support Forum
to aid the designer.
In-Circuit Emulator
A low-cost, high-functionality in-circuit emulator (ICE) is
available for development support. This hardware can program
single devices.
The emulator consists of a base unit that connects to the PC
using a USB port. The base unit is universal and operates with
all PSoC devices. Emulation pods for each device family are
available separately. The emulation pod takes the place of the
PSoC device in the target board and performs full-speed
(24 MHz) operation.
Page 6 of 40
CY8C21345
CY8C22345
CY8C22545
Designing with PSoC Designer
The development process for the PSoC device differs from that
of a traditional fixed function microprocessor. The configurable
analog and digital hardware blocks give the PSoC architecture a
unique flexibility that pays dividends in managing specification
change during development and by lowering inventory costs.
These configurable resources, called PSoC Blocks, have the
ability to implement a wide variety of user-selectable functions.
The PSoC development process is summarized in four steps:
specifications. Each datasheet describes the use of each user
module parameter, and other information you may need to
successfully implement your design.
Organize and Connect
You build signal chains at the chip level by interconnecting user
modules to each other and the I/O pins. You perform the
selection, configuration, and routing so that you have complete
control over all on-chip resources.
1. Select User Modules.
Generate, Verify, and Debug
2. Configure User Modules.
When you are ready to test the hardware configuration or move
on to developing code for the project, you perform the “Generate
Configuration Files” step. This causes PSoC Designer to
generate source code that automatically configures the device to
your specification and provides the software for the system. The
generated code provides application programming interfaces
(APIs) with high-level functions to control and respond to
hardware events at run-time and interrupt service routines that
you can adapt as needed.
3. Organize and Connect.
4. Generate, Verify, and Debug.
Select User Modules
PSoC Designer provides a library of prebuilt, pretested hardware
peripheral components called “user modules.” User modules
make selecting and implementing peripheral devices, both
analog and digital, simple.
Configure User Modules
Each user module that you select establishes the basic register
settings that implement the selected function. They also provide
parameters and properties that allow you to tailor their precise
configuration to your particular application. For example, a PWM
User Module configures one or more digital PSoC blocks, one
for each 8 bits of resolution. The user module parameters permit
you to establish the pulse width and duty cycle. Configure the
parameters and properties to correspond to your chosen
application. Enter values directly or by selecting values from
drop-down menus. All the user modules are documented in
datasheets that may be viewed directly in PSoC Designer or on
the Cypress website. These user module datasheets explain the
internal operation of the user module and provide performance
Document Number: 001-43084 Rev. *V
A complete code development environment allows you to
develop and customize your applications in either C, assembly
language, or both.
The last step in the development process takes place inside
PSoC Designer’s debugger (access by clicking the Connect
icon). PSoC Designer downloads the HEX image to the ICE
where it runs at full speed. PSoC Designer debugging
capabilities rival those of systems costing many times more. In
addition to traditional single-step, run-to-breakpoint, and
watch-variable features, the debug interface provides a large
trace buffer and allows you to define complex breakpoint events.
These include monitoring address and data bus values, memory
locations, and external signals.
Page 7 of 40
CY8C21345
CY8C22345
CY8C22545
Pinouts
This PSoC device family is available in a variety of packages that are listed in the following tables. Every port pin (labeled with a “P”)
is capable of Digital I/O. However, Vss, Vdd, and XRES are not capable of Digital I/O.
CY8C22345, CY8C21345 28-pin SOIC
Table 2. Pin Definitions
Pin No.
Type
Digital Analog
Pin Name
Description
1
I/O
I, MR
P0[7]
Integration Capacitor for MR
2
I/O
I, ML
P0[5]
Integration Capacitor for ML
3
I/O
I, ML
P0[3]
4
I/O
I, ML
P0[1]
5
I/O
I, ML
P2[7]
To Compare Column 0
6
I/O
ML
P2[5]
Optional ADC External Vref
7
I/O
ML
P2[3]
8
I/O
ML
P2[1]
9
Power
Vss
Ground Connection [5]
10
I/O
ML
P1[7]
I2C serial clock (SCL)
I2C serial data (SDA)
11
I/O
ML
P1[5]
12
I/O
ML
P1[3]
13
I/O
ML
P1[1]
I2C serial clock (SCL),
ISSP-SCLK [6]
Vss
Ground Connection [5]
I2C serial Clock (SCL),
ISSP-SDATA [6]
14
Power
15
I/O
MR
P1[0]
16
I/O
MR
P1[2]
17
I/O
MR
P1[4]
18
I/O
19
MR
Input
I/O
MR
21
I/O
MR
P2[2]
22
I/O
MR
P2[4]
23
I/O
I, MR
P2[6]
24
I/O
I, MR
P0[0]
25
I/O
I, MR
P0[2]
26
I/O
I, MR
P0[4]
27
I/O
I, MR
P0[6]
Power
AI, MR, P0[7]
AI, ML, P0[5]
AI, ML, P0[3]
AI, ML, P0[1]
AI, ML, P2[7]
ADC_Ext_Vref, ML, P2[5]
ML, P2[3]
ML, P2[1]
Vss
I2C SCL, ML, P1[7]
I2C SDA, ML, P1[5]
ML, P1[3]
I2C SCL, ML, P1[1]
Vss
1
2
3
4
5
6
7
8
9
10
11
12
13
14
SOIC
28
27
26
25
24
23
22
21
20
19
18
17
16
15
Vdd
P0[6], MR, AI
P0[4], MR, AI
P0[2], MR, AI
P0[0], MR, AI
P2[6], MR, AI
P2[4], MR
P2[2], MR
P2[0], MR
XRES
P1[6], MR
P1[4], MR, EXTCLK
P1[2], MR
P1[0], MR, I2C SDATA
Optional external clock input
(EXT-CLK)
P1[6]
XRES
20
28
Figure 3. Pin Diagram
Active High Pin Reset with
Internal Pull Down
P2[0]
Vdd
To Compare Column 1
Supply Voltage
LEGEND: A = Analog, I = Input, O = Output, M=Analog Mux input, MR= Analog Mux right input, ML= Analog Mux left input.
Notes
5. All VSS pins should be brought out to one common GND plane.
6. If ISSP is not used, pins P1[0] and P1[1] will respond differently to a POR or XRES event. After a POR or XRES event, both pins are pulled down to ground by going
into the resistive zero Drive mode, before reaching the High Z Drive mode.
Document Number: 001-43084 Rev. *V
Page 8 of 40
CY8C21345
CY8C22345
CY8C22545
CY8C22545 44-pin TQFP
Table 3. Pin Definitions [7]
Pin Name
I/O
MR
P1[2]
20
21
22
23
24
25
26
I/O
I/O
I/O
I/O
I/O
I/O
MR
MR
MR
MR
MR
MR
P1[4]
P1[6]
P3[0]
P3[2]
P3[4]
P3[6]
XRES
27
I/O
MR
P4[0]
28
I/O
MR
P4[2]
29
I/O
MR
P4[4]
Power
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
ML
ML
ML
ML
ML
ML
ML
ML
Power
Input
30
Power
Vss
31
I/O
MR
P2[0]
32
I/O
MR
P2[2]
33
I/O
MR
P2[4]
34
I/O
I, MR
P2[6]
35
I/O
I, MR
P0[0]
36
I/O
I, MR
P0[2]
37
I/O
I, MR
P0[4]
38
I/O
I, MR
P0[6]
39
Power
Supply Voltage
Ground Connection
I2C serial clock (SCL)
I2C serial data (SDA)
ADC_Ext_Vref, ML, P2[5]
ML, P2[3]
ML, P2[1]
Vdd
ML, P4[5]
ML, P4[3]
ML, P4[1]
Vss
ML, P3[7]
ML, P3[5]
ML, P3[3]
Crystal (XTALin), I2C SCL, ISSP SCLK[6]
Ground Connection
Crystal (XTALout),
I2C SDA, ISSP
]
SDATA[6
1
2
3
4
5
TQFP
6
7
8
9
10
11
33
32
31
30
29
28
27
26
25
24
23
P2[4], MR
P2[2], MR
P2[0], MR
Vss
P4[4], MR
P4[2], MR
P4[0], MR
XRES
P3[6], MR
P3[4], MR
P3[2], MR
MR, P1[6]
MR, P3[0]
19
ML
ML
ML
P0[5], ML, AI
P0[7], MR, AI
Vdd
P0[6], MR, AI
P0[4], MR, AI
P0[2], MR, AI
P0[0], MR, AI
P2[6], MR, AI
MR
Power
I/O
I/O
I/O
Optional ADC External Vref
41
40
I/O
P2[5]
P2[3]
P2[1]
Vdd
P4[5]
P4[3]
P4[1]
Vss
P3[7]
P3[5]
P3[3]
P3[1]
P1[7]
P1[5]
P1[3]
P1[1]
Vss
P1[0]
39
38
37
36
35
34
ML
ML
ML
P2[7], ML, AI
P0[1], ML, AI
P0[3], ML, AI
I/O
I/O
I/O
Figure 4. Pin Diagram
44
43
42
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Description
12
13
14
15
16
17
18
19
20
21
22
Analog
ML, P3[1]
Type
Digital
I2C SCL, ML, P1[7]
I2C SDA, ML, P1[5]
ML, P1[3]
I2C SCL, XTALin, ML, P1[1]
Vss
I2C SDA, XTALout, MR, P1[0]
MR, P1[2]
EXTCLK, MR, P1[4]
Pin No.
Optional external clock input (EXTCLK)
Active High Pin Reset with Internal Pull
Down
Ground Connection
To Compare Column 1
Vdd
Supply Voltage
40
I/O
I, MR
P0[7]
Integration Capacitor for MR
41
I/O
I, ML
P0[5]
Integration Capacitor for ML
42
I/O
I, ML
P0[3]
43
I/O
I, ML
P0[1]
44
I/O
I, ML
P2[7]
To Compare Column 0
LEGEND: A = Analog, I = Input, O = Output, M=Analog Mux input, MR= Analog Mux right input, ML= Analog Mux left input.
Note
7. All VSS pins should be brought out to one common GND plane.
Document Number: 001-43084 Rev. *V
Page 9 of 40
CY8C21345
CY8C22345
CY8C22545
Registers
This section lists the registers of this PSoC device family by mapping tables. For detailed register information, refer the PSoC
Programmable System-on Chip Technical Reference Manual.
Register Conventions
Register Mapping Tables
Table 4. Abbreviations
The PSoC device has a total register address space of 512
bytes. The register space is also referred to as I/O space and is
broken into two parts. The XIO bit in the Flag register determines
which bank the user is currently in. When the XIO bit is set, the
user is said to be in the “extended” address space or the
“configuration” registers.
Convention
Description
RW
Read and write register or bit(s)
R
Read register or bit(s)
W
Write register or bit(s)
L
Logical register or bit(s)
C
Clearable register or bit(s)
#
Access is bit specific
Document Number: 001-43084 Rev. *V
Note In the following register mapping tables, blank fields are
Reserved and must not be accessed.
Page 10 of 40
CY8C21345
CY8C22345
CY8C22545
Table 5. Register Map Bank 0 Table: User Space
Name
PRT0DR
PRT0IE
PRT0GS
PRT0DM2
PRT1DR
PRT1IE
PRT1GS
PRT1DM2
PRT2DR
PRT2IE
PRT2GS
PRT2DM2
PRT3DR
PRT3IE
PRT3GS
PRT3DM2
PRT4DR
PRT4IE
PRT4GS
PRT4DM2
Addr (0,Hex) Access
Name
00
RW
01
RW
02
RW
03
RW
04
RW
05
RW
06
RW
07
RW
08
RW
09
RW
0A
RW
0B
RW
0C
RW
0D
RW
0E
RW
0F
RW
10
RW
CSD0_DR0_L
11
RW
CSD0_DR1_L
12
RW
CSD0_CNT_L
13
RW
CSD0_CR0
14
RW
CSD0_DR0_H
15
RW
CSD0_DR1_H
16
RW
CSD0_CNT_H
17
RW
CSD0_CR1
18
RW
CSD1_DR0_L
19
RW
CSD1_DR1_L
1A
RW
CSD1_CNT_L
1B
RW
CSD1_CR0
1C
RW
CSD1_DR0_H
1D
RW
CSD1_DR1_H
1E
RW
CSD1_CNT_H
1F
RW
CSD_CR1
DBC00DR0
20
#
AMX_IN
DBC00DR1
21
W
AMUX_CFG
DBC00DR2
22
RW
PWM_CR
DBC00CR0
23
#
ARF_CR
DBC01DR0
24
#
CMP_CR0
DBC01DR1
25
W
ASY_CR
DBC01DR2
26
RW
CMP_CR1
DBC01CR0
27
#
DCC02DR0
28
#
ADC0_CR
DCC02DR1
29
W
ADC1_CR
DCC02DR2
2A
RW
SADC_DH
DCC02CR0
2B
#
SADC_DL
DCC03DR0
2C
#
TMP_DR0
DCC03DR1
2D
W
TMP_DR1
DCC03DR2
2E
RW
TMP_DR2
DCC03CR0
2F
#
TMP_DR3
DBC10DR0
30
#
DBC10DR1
31
W
DBC10DR2
32
RW
ACB00CR1*
DBC10CR0
33
#
ACB00CR2*
DBC11DR0
34
#
DBC11DR1
35
W
DBC11DR2
36
RW
ACB01CR1*
DBC11CR0
37
#
ACB01CR2*
DCC12DR0
38
#
DCC12DR1
39
W
DCC12DR2
3A
RW
DCC12CR0
3B
#
DCC13DR0
3C
#
DCC13DR1
3D
W
DCC13DR2
3E
RW
DCC13CR0
3F
#
Shaded fields are Reserved and must not be accessed.
Document Number: 001-43084 Rev. *V
Addr (0,Hex)
40
41
42
43
44
45
46
47
48
49
4A
4B
4C
4D
4E
4F
50
51
52
53
54
55
56
57
58
59
5A
5B
5C
5D
5E
5F
60
61
62
63
64
65
66
67
68
69
6A
6B
6C
6D
6E
6F
70
71
72*
73*
74
75
76*
77*
78
79
7A
7B
7C
7D
7E
7F
Access
#
W
RW
#
#
W
RW
#
#
W
RW
#
#
W
RW
#
R
W
R
#
R
W
R
RW
R
W
R
#
R
W
R
RW
RW
RW
RW
RW
#
#
RW
RW
#
#
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
Name
ASC10CR0*
Addr (0,Hex) Access
Name
80*
RW
81
RW
82
RW
83
RW
ASD11CR0*
84*
RW
85
RW
86
RW
87
RW
88
RW
PWMVREF0
89
RW
PWMVREF1
8A
RW
IDAC_MODE
8B
RW
PWM_SRC
8C
RW
TS_CR0
8D
RW
TS_CMPH
8E
RW
TS_CMPL
8F
RW
TS_CR1
90
RW
CUR PP
91
RW
STK_PP
92
RW
PRV PP
93
RW
IDX_PP
94
RW
MVR_PP
95
RW
MVW_PP
96
RW
I2C0_CFG
97
RW
I2C0_SCR
98
RW
I2C0_DR
99
RW
I2C0_MSCR
9A
RW
INT_CLR0
9B
RW
INT_CLR1
9C
RW
INT_CLR2
9D
RW
INT_CLR3
9E
RW
INT_MSK3
9F
RW
INT_MSK2
A0
INT_MSK0
A1
INT_MSK1
A2
INT_VC
A3
RES_WDT
A4
DEC_DH
A5
DEC_DL
A6
DEC _CR0*
A7
DEC_CR1*
A8
W
MUL0_X
A9
W
MUL0_Y
AA
R
MUL0_DH
AB
R
MUL0_DL
AC
RW
ACC0_DR1
AD
RW
ACC0_DR0
AE
RW
ACC0_DR3
AF
RW
ACC0_DR2
RDI0RI
B0
RW
CPU A
RDI0SYN
B1
RW
CPU_T1
RDI0IS
B2
RW
CPU_T2
RDI0LT0
B3
RW
CPU_X
RDI0LT1
B4
RW
CPU PCL
RDI0RO0
B5
RW
CPU_PCH
RDI0RO1
B6
RW
CPU_SP
RDI0DSM
B7
RW
CPU_F
RDI1RI
B8
RW
CPU_TST0
RDI1SYN
B9
RW
CPU_TST1
RDI1IS
BA
RW
CPU_TST2
RDI1LT0
BB
RW
CPU TST3
RDI1LT1
BC
RW
DAC1_D
RDI1RO0
BD
RW
DAC0_D
RDI1RO1
BE
RW
CPU_SCR1
RDI1DSM
BF
RW
CPU_SCR0
# Access is bit specific. * has a different meaning.
Addr (0,Hex)
C0
C1
C2
C3
C4
C5
C6
C7
C8
C9
CA
CB
CC
CD
CE
CF
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
DA
DB
DC
DD
DE
DF
E0
E1
E2
E3
E4
E5
E6
E7
E8
E9
EA
EB
EC
ED
EE
EF
F0
F1
F2
F3
F4
F5
F6
F7
F8
F9
FA
FB
FC
FD
FE
FF
Access
RW
RW
RW
RW
RW
RW
RW
RW
#
#
RW
#
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
#
RW
#
RW
RW
RW
RW
RW
RW
RW
RW
RC
W
RW
RW
RW
RW
W
W
R
R
RW
RW
RW
RW
#
#
#
#
#
#
#
I
RW
RW
RW
#
RW
RW
#
#
Page 11 of 40
CY8C21345
CY8C22345
CY8C22545
Table 6. Register Map Bank 1 Table: Configuration Space
Name
PRT0DM0
PRT0DM1
PRT0IC0
PRT0IC1
PRT1DM0
PRT1DM1
PRT1IC0
PRT1IC1
PRT2DM0
PRT2DM1
PRT2IC0
PRT2IC1
PRT3DM0
PRT3DM1
PRT3IC0
PRT3IC1
PRT4DM0
PRT4DM1
PRT4IC0
PRT4IC1
Addr (1,Hex) Access Name
0
RW
1
RW
2
RW
3
RW
4
RW
5
RW
6
RW
7
RW
8
RW
9
RW
0A
RW
0B
RW
0C
RW
0D
RW
0E
RW
0F
RW
10
RW
CMP0CR1
11
RW
CMP0CR2
12
RW
13
RW
VDAC50CR0
14
RW
CMP1CR1
15
RW
CMP1CR2
16
RW
17
RW
VDAC51CR0
18
RW
CSCMPCR0
19
RW
CSCMPGOEN
1A
RW
CSLUTCR0
1B
RW
CMPCOLMUX
1C
RW
CMPPWMCR
1D
RW
CMPFLTCR
1E
RW
CMPCLK1
1F
RW
CMPCLK0
DBC00FN
20
RW
CLK_CR0
DBC00IN
21
RW
CLK_CR1
DBC00OU
22
RW
ABF_CR0
DBC00CR1
23
RW
AMD_CR0
DBC01FN
24
RW
CMP_GO_EN
DBC01IN
25
RW
CMP_GO_EN1
DBC01OU
26
RW
AMD_CR1
DBC01CR1
27
RW
ALT_CR0
DCC02FN
28
RW
ALT_CR1
DCC02IN
29
RW
CLK_CR2
DCC02OU
2A
RW
DBC02CR1
2B
RW
CLK_CR3
DCC03FN
2C
RW
TMP_DR0
DCC03IN
2D
RW
TMP_DR1
DCC03OU
2E
RW
TMP_DR2
DBC03CR1
2F
RW
TMP_DR3
DBC10FN
30
RW
DBC10IN
31
RW
DBC10OU
32
RW
ACB00CR1*
DBC10CR1
33
RW
ACB00CR2*
DBC11FN
34
RW
DBC11IN
35
RW
DBC11OU
36
RW
ACB01CR1*
DBC11CR1
37
RW
ACB01CR2*
DCC12FN
38
RW
DCC12IN
39
RW
DCC12OU
3A
RW
DBC12CR1
3B
RW
DCC13FN
3C
RW
DCC13IN
3D
RW
DCC13OU
3E
RW
DBC13CR1
3F
RW
Shaded fields are Reserved and must not be accessed.
Document Number: 001-43084 Rev. *V
Addr (1,Hex)
40
41
42
43
44
45
46
47
48
49
4A
4B
4C
4D
4E
4F
50
51
52
53
54
55
56
57
58
59
5A
5B
5C
5D
5E
5F
60
61
62
63
64
65
66
67
68
69
6A
6B
6C
6D
6E
6F
70
71
72
73
74
75
76*
77*
78
79
7A
7B
7C
7D
7E
7F
Access
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
#
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
Name
ASC10CR0*
Addr (1,Hex) Access Name
80*
RW
81
RW
82
RW
83
RW
ASD11CR0*
84*
RW
85
RW
86
RW
87
RW
88
RW
89
RW
8A
RW
8B
RW
8C
RW
8D
RW
8E
RW
8F
RW
90
RW
GDI_O_IN
91
RW
GDI_E_IN
92
RW
GDI_O_OU
93
RW
GDI_E_OU
94
RW
95
RW
96
RW
97
RW
98
RW
MUX_CR0
99
RW
MUX_CR1
9A
RW
MUX_CR2
9B
RW
MUX_CR3
9C
RW
DAC_CR1#
9D
RW
OSC_GO_EN
9E
RW
OSC_CR4
9F
RW
OSC_CR3
GDI_O_IN_CR
A0
RW
OSC_CR0
GDI_E_IN_CR
A1
RW
OSC_CR1
GDI_O_OU_CR A2
RW
OSC_CR2
GDI_E_OU_CR A3
RW
VLT_CR
RTC_H
A4
RW
VLT_CMP
RTC_M
A5
RW
ADC0_TR*
RTC_S
A6
RW
ADC1_TR*
RTC_CR
A7
RW
V2BG_TR
SADC_CR0
A8
RW
IMO_TR
SADC_CR1
A9
RW
ILO_TR
SADC_CR2
AA
RW
BDG_TR
SADC_CR3TRIM AB
RW
ECO_TR
SADC_CR4
AC
RW
MUX_CR4
I2C0_AD
AD
RW
MUX_CR5
AE
RW
MUX_CR6
AF
RW
MUX_CR7
RDI0RI
B0
RW
CPU A
RDI0SYN
B1
RW
CPU_T1
RDI0IS
B2
RW
CPU_T2
RDI0LT0
B3
RW
CPU_X
RDI0LT1
B4
RW
CPU_PCL
RDI0RO0
B5
RW
CPU_PCH
RDI0RO1
B6
RW
CPU_SP
RDI0DSM
B7
RW
CPU_F
RDI1RI
B8
RW
FLS_PR0
RDI1SYN
B9
RW
FLS TR
RDI1IS
BA
RW
FLS_PR1
RDI1LT0
BB
RW
RDI1LT1
BC
RW
FAC_CR0
RDI1RO0
BD
RW
DAC_CR0#
RDI1RO1
BE
RW
CPU_SCR1
RDI1DSM
BF
RW
CPU_SCR0
# Access is bit specific. * has a different meaning.
Addr (1,Hex)
C0
C1
C2
C3
C4
C5
C6
C7
C8
C9
CA
CB
CC
CD
CE
CF
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
DA
DB
DC
DD
DE
DF
E0
E1
E2
E3
E4
E5
E6
E7
E8
E9
EA
EB
EC
ED
EE
EF
F0
F1
F2
F3
F4
F5
F6
F7
F8
F9
FA
FB
FC
FD
FE
FF
Access
RW
RW
RW
RW
RW
RW
RW
RW
#
RW
RW
RW
#
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
R
RW
RW
RW
W
W
RW
W
RW
RW
RW
RW
#
#
#
#
#
#
#
I
RW
W
RW
SW
RW
#
#
Page 12 of 40
CY8C21345
CY8C22345
CY8C22545
Electrical Specifications
This section presents the DC and AC electrical specifications of this PSoC device family. For the latest electrical specifications, check
the most recent data sheet by visiting http://www.cypress.com.
Specifications are valid for –40 °C  TA  85 °C and TJ  100 °C, except where noted. Specifications for devices running at greater
than 12 MHz are valid for –40 °C  TA  70 °C and TJ  82 °C.
Figure 5. Voltage versus Operating Frequency
5.25
Vdd Voltage
lid n g
Va rati n
e io
Op Reg
4.75
3.00
93 kHz
12 MHz
24 MHz
CPU Frequency
Document Number: 001-43084 Rev. *V
Page 13 of 40
CY8C21345
CY8C22345
CY8C22545
Absolute Maximum Ratings
Exceeding maximum ratings may shorten the useful life of the device. User guidelines are not tested.
Table 7. Absolute Maximum Ratings
Symbol
Description
Min
Typ
Max
Units
–55
–
+100
°C
–
125
See Package
label
°C
See package
label
–
72
Hours
–40
–
+85
°C
–0.5
–
+6.0
V
Vss - 0.5
–
Vdd + 0.5
V
Vss - 0.5
–
Vdd + 0.5
V
Maximum current into any port pin
–25
–
+50
mA
ESD
Electr static discharge voltage
2000
–
–
V
LU
Latch up current
–
–
200
mA
TSTG
Storage temperature
TBAKETEMP
Bake temperature
TBAKETIME
Bake time
TA
Ambient temperature with power applied
Vdd
Supply voltage on Vdd relative to Vss
VIO
DC input voltage
VIOz
DC voltage applied to tristate
IMIO
Notes
Higher storage
temperatures reduce
data retention time
Human Body Model ESD
Operating Temperature
Table 8. Operating Temperature
Min
Typ
Max
Units
TA
Symbol
Ambient temperature
Description
–40
–
+85
°C
TJ
Junction temperature
–40
–
+100
°C
Document Number: 001-43084 Rev. *V
Notes
The temperature rise
from ambient to junction
is package specific. See
Table 30 on page 28. The
user must limit the power
consumption to comply
with this requirement.
Page 14 of 40
CY8C21345
CY8C22345
CY8C22545
DC Electrical Characteristics
DC Chip Level Specifications
Table 9 lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and
–40 °C  TA  85 °C, or 3.0 V to 3.6 V and –40 °C  TA  85 °C, respectively. Typical parameters apply to 5 V and 3.3 V at 25 °C, and
are for design guidance only, unless specified otherwise.
Table 9. DC Chip Level Specifications
Symbol
Description
Min
Typ
Max
Units
Notes
Vdd
Supply voltage
3.0
–
5.25
V
See Table 17 on page 19
IDD
Supply current
–
7
12
mA
Conditions are Vdd = 5.0 V,
25°C, CPU = 3 MHz, 48 MHz disabled.
VC1 = 1.5 MHz
VC2 = 93.75 kHz
VC3 = 93.75 kHz
IDD3
Supply current
–
4
7
mA
Conditions are Vdd = 3.3 V
TA = 25 °C, CPU = 3 MHz
48 MHz = Disabled
VC1 = 1.5 MHz, VC2 = 93.75 kHz
VC3 = 93.75 kHz
ISB
Sleep (Mode) Current with POR, LVD,
Sleep Timer, and WDT[8]
–
3
6.5
A
Conditions are with internal slow speed
oscillator, Vdd = 3.3 V
–40°C <= TA <= 55°C
ISBH
Sleep (Mode) Current with POR, LVD,
Sleep Timer, and WDT at high
temperature[8]
–
4
25
A
Conditions are with internal slow speed
oscillator, Vdd = 3.3 V
55 °C < TA <= 85 °C
ISBXTL
Sleep (Mode) Current with POR, LVD,
Sleep Timer, WDT, and external crystal[8]
–
4
7.5
A
Conditions are with properly loaded,
1 W max, 32.768 kHz crystal.
Vdd = 3.3 V, –40 °C <= TA <= 55 °C
ISBXTLH
Sleep (Mode) Current with POR, LVD,
Sleep Timer, WDT, and external crystal at
high temperature [8]
–
5
26
A
Conditions are with properly loaded,
1W max, 32.768 kHz crystal.
Vdd = 3.3 V, 55 °C < TA <= 85 °C
VREF
Reference Voltage (Bandgap)
1.275
1.3
1.325
V
Trimmed for appropriate Vdd
Note
8. Standby current includes all functions (POR, LVD, WDT, Sleep Time) needed for reliable system operation. This must be compared with devices that have similar
functions enabled.
Document Number: 001-43084 Rev. *V
Page 15 of 40
CY8C21345
CY8C22345
CY8C22545
DC GPIO Specifications
Table 10 lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and
–40 °C  TA  85 °C, or 3.0 V to 3.6 V and –40 °C  TA  85 °C, respectively. Typical parameters apply to 5 V and 3.3 V at 25 °C and
are for design guidance only, unless otherwise specified.
Table 10. DC GPIO Specifications
Min
Typ
Max
Units
RPU
Symbol
Pull-up resistor
4
5.6
8
k
RPD [9]
Pull-down resistor
4
5.6
8
k
VOH
High output level
Vdd – 1.0
–
–
V
IOH = 10 mA, Vdd = 4.75 to 5.25 V
(8 total loads, 4 on even port pins (for
example, P0[2], P1[4]), 4 on odd port
pins (for example, P0[3], P1[5])).
80 mA maximum combined IOH budget
VOL
Low output level
–
–
0.75
V
IOL = 25 mA, Vdd = 4.75 to 5.25 V
(8 total loads, 4 on even port pins (for
example, P0[2], P1[4]), 4 on odd port
pins (for example, P0[3], P1[5])).
150 mA maximum combined IOL budget.
IOH
High level source current
10
–
–
mA
VOH = Vdd – 1.0 V, see the limitations of
the total current in the note for VOH.
IOL
Low level sink current
25
–
–
mA
VOL = 0.75 V, see the limitations of the
total current in the note for VOL.
VIL [9]
Input Low level
–
–
0.8
V
Vdd = 3.0 to 5.25
VIH [9]
Input High level
2.1
–
V
Vdd = 3.0 to 5.25
[9]
Input hysterisis
–
60
–
mV
Input leakage (absolute value)
–
1
–
nA
Gross tested to 1 A
Capacitive load on pins as input
–
3.5
10
pF
Package and pin dependent.
Temp = 25 °C
Capacitive load on pins as output
–
3.5
10
pF
Package and pin dependent.
Temp = 25 °C
VH
IIL
[9]
CIN
[9]
COUT
Description
Notes
Note
9. The DC GPIO specifications apply to the XRES pin as well.
Document Number: 001-43084 Rev. *V
Page 16 of 40
CY8C21345
CY8C22345
CY8C22545
DC Operational Amplifier Specifications
The following tables list the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to
5.25 V and –40 °C  TA  85 °C, 3.0 V to 3.6 V and –40 °C  TA  85 °C respectively. Typical parameters apply to 5 V or 3.3 V at 25 °C
and are for design guidance only.
Table 11. 5 V DC Operational Amplifier Specifications
Symbol
VOSOA
Description
Min
Typ
Max
Units
–
2.5
15
mV
Input offset voltage (absolute value)
Notes
TCVOSOA Average input offset voltage drift
–
10
–
V/°C
IEBOA[10]
Input leakage current (Port 0 Analog Pins)
–
200
–
pA
Gross tested to 1 A
CINOA
Input capacitance (Port 0 Analog Pins)
–
4.5
9.5
pF
Package and pin dependent.
Temp = 25 °C
VCMOA
Common mode Voltage Range
0.0
–
Vdd - 1
V
Min
Typ
Max
Units
Table 12. 3.3 V DC Operational Amplifier Specifications
Symbol
Description
Notes
VOSOA
Input offset voltage (absolute value)
–
2.5
15
mV
TCVOSOA
Average input offset voltage drift
–
10
–
V/°C
IEBOA[10]
Input leakage current (Port 0 Analog Pins)
–
200
–
pA
Gross tested to 1 A
CINOA
Input capacitance (Port 0 Analog Pins)
–
4.5
9.5
pF
Package and pin dependent.
Temp = 25 °C
VCMOA
Common mode voltage range
0
–
Vdd – 1
V
DC IDAC Specifications
The following table lists the guaranteed maximum and minimum specifications for automotive A-grade and E-grade devices. Unless
otherwise noted, all specifications in the table apply to A-grade devices for the voltage and temperature ranges of: 4.75 V to 5.25 V
and –40 °C to 85 °C, or 3.0 V to 3.6 V and –40 °C to 85 °C. Unless otherwise noted, all specifications in the table also apply to E-grade
devices for the voltage and temperature ranges of: 4.75 V to 5.25 V and –40 °C to 85 °C. Typical parameters apply to 5 V and 3.3 V
at 25 °C, unless specified otherwise, and are for design guidance only.
Table 13. DC IDAC Specifications
Symbol
Min
Typ
Max
Units
–
75.4
218
nA/bit IDAC gain at 1x current gain
–
335
693
nA/bit IDAC gain at 4x current gain
–
1160
2410
nA/bit IDAC gain at 16x current gain
–
2340
5700
nA/bit IDAC gain at 32x current gain
Monotonicity
No
–
–
–
IDACGAIN_VAR IDAC gain variation over
temperature –40 °C to 85 °C
–
3.22
–
nA
at 1x current gain
–
18.1
–
nA
at 4x current gain
–
59.9
–
nA
at 16x current gain
–
120
–
nA
at 32x current gain
–
19.2
–
µA
at 1x current gain
–
85.4
–
µA
at 4x current gain
–
295
–
µA
at 16x current gain
–
596
–
µA
at 32x current gain
IDACGAIN
IIDAC
Description
IDAC gain
IDAC current at maximum code
(0xFF)
Notes
IDAC gain is non-monotonous at
step intervals of (0x10)
Note
10. Atypical behavior: IEBOA of Port 0 Pin 0 is below 1 nA at 25 °C; 50 nA over temperature. Use Port 0 Pins 1-7 for the lowest leakage of 200 nA.
Document Number: 001-43084 Rev. *V
Page 17 of 40
CY8C21345
CY8C22345
CY8C22545
DC Low Power Comparator Specifications
Table 14 lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and
–40 °C  TA  85 °C, 3.0 V to 3.6 V and –40 °C  TA  85 °C respectively. Typical parameters apply to 5 V at 25 °C and are for design
guidance only.
Table 14. DC Low Power Comparator Specifications
Symbol
Description
VREFLPC
Low power comparator (LPC) reference
voltage range
VOSLPC
LPC voltage offset
Min
Typ
Max
Units
0.2
–
Vdd – 1
V
–
2.5
30
mV
Notes
SAR10 ADC DC Specifications
Table 15 lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and
–40 °C  TA  85 °C, or 3.0 V to 3.6 V and –40 °C  TA  85 °C, respectively. Typical parameters apply to 5 V or 3.3 V at 25 °C and
are for design guidance only.
Table 15. SAR10 ADC DC Specifications
Description
Min
Typ
Max
Units
Notes
Vadcvref
Symbol
Reference voltage at pin P2[5] when configured
as ADC reference voltage
3.0
–
5.25
V
When VREF is buffered inside
ADC, the voltage level at P2[5]
(when configured as ADC
reference voltage) must be
always maintained to be at least
300 mV less than the chip supply
voltage level on Vdd pin.
(Vadcvref < Vdd)
Iadcvref
Current when P2[5] is configured as ADC VREF
–
–
0.5
mA
Disables the internal voltage
reference buffer
INL at 10 bits
Integral Nonlinearity
–2.5
–
2.5
LSB
For VDD  3.0 V and Vref  3.0 V
–5.0
–
5.0
LSB
For VDD < 3.0 V or Vref < 3.0 V
–1.5
–
1.5
LSB
For VDD 3.0 V and Vref  3.0 V
–4.0
–
4.0
LSB
For VDD < 3.0 V or Vref < 3.0 V
–
–
150
ksps Resolution 10 bits
DNL at 10 bits Differential Nonlinearity
SPS [11]
Sample per second
Note
11. Errata: When ADC is operated in free running mode, for a constant input voltage output of ADC can have a variation of up to 7LSB. This can be resolved by using
the averaging technique or by disabling the free running mode before reading the data and enabling again after reading the data. For more information, see “Errata”
on page 35.
Document Number: 001-43084 Rev. *V
Page 18 of 40
CY8C21345
CY8C22345
CY8C22545
DC Analog Mux Bus Specifications
Table 16 lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and
–40 °C  TA  85 °C or 3.0 V to 3.6 V and –40 °C  TA  85 °C, respectively. Typical parameters apply to 5 V or 3.3 V at 25 °C and
are for design guidance only.
Table 16. DC Analog Mux Bus Specifications
Min
Typ
Max
Units
RSW
Symbol
Switch Resistance to Common Analog Bus
Description
–
–
400

Rgnd
Resistance of Initialization Switch to gnd
–
–
800

Notes
Vdd 3.00
DC POR and LVD Specifications
Table 17 lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and
–40 °C  TA  85 °C or 3.0 V to 3.6 V and –40 °C  TA  85 °C, respectively. Typical parameters apply to 5 V or 3.3 V at 25 °C and
are for design guidance only.
Table 17. DC POR and LVD Specifications
Symbol
Description
VPPOR1
VPPOR2
Vdd Value for PPOR Trip
PORLEV[1:0] = 01b
PORLEV[1:0] = 10b
VLVD2
VLVD3
VLVD4
VLVD5
VLVD6
VLVD7
Vdd Value for LVD Trip
VM[2:0] = 010b
VM[2:0] = 011b
VM[2:0] = 100b
VM[2:0] = 101b
VM[2:0] = 110b
VM[2:0] = 111b
Document Number: 001-43084 Rev. *V
Min
Typ
Max
Units
–
2.82
4.55
2.95
4.70
V
V
2.95
3.06
4.37
4.50
4.62
4.71
3.02
3.13
4.48
4.64
4.73
4.81
3.09
3.20
4.55
4.75
4.83
4.95
V
V
V
V
V
V
Notes
Vdd must be greater than or
equal to 3.0 V during startup,
reset from the XRES pin, or
reset from Watchdog.
Page 19 of 40
CY8C21345
CY8C22345
CY8C22545
DC Programming Specifications
Table 18 lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and
–40 °C  TA  85 °C or 3.0 V to 3.6 V and –40 °C  TA  85 °C, respectively. Typical parameters apply to 5 V or 3.3 V at 25 °C and
are for design guidance only.
Table 18. DC Programming Specifications
Min
Typ
Max
Units
Notes
VDDP
Symbol
VDD for programming and erase
Description
4.5
5.0
5.5
V
This specification applies to
the functional requirements of
external programmer tools
VDDLV
Low VDD for verify
3.0
3.1
3.2
V
This specification applies to
the functional requirements of
external programmer tools
VDDHV
High VDD for verify
5.1
5.2
5.3
V
This specification applies to
the functional requirements of
external programmer tools
3.0
–
5.25
V
This specification applies to
this device when it is executing
internal flash writes
VDDIWRITE Supply voltage for flash write operation
IDDP
Supply Current during Programming or Verify
–
5
25
mA
VILP
Input Low Voltage during Programming or
Verify
–
–
0.8
V
VIHP
Input High Voltage during Programming or
Verify
2.2
–
–
V
IILP
Input Current when Applying VILP to P1[0] or
P1[1] during Programming or Verify
–
–
0.2
mA
Driving internal pull down
resistor
IIHP
Input Current when Applying VIHP to P1[0] or
P1[1] during Programming or Verify
–
–
1.5
mA
Driving internal pull down
resistor
VOLV
Output Low Voltage during Programming or
Verify
–
–
Vss + 0.75
V
VOHV
Output High Voltage during Programming or
Verify
Vdd - 1.0
–
Vdd
V
50,000
–
–
–
Erase/write cycles per block
1,800,000
–
–
–
Erase/write cycles
10
–
–
Years
FlashENPB Flash Endurance (per block)[13]
(total)[12]
FlashENT
Flash Endurance
FlashDR
Flash Data Retention
DC I2C Specifications
Table 19 lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and
–40 °C  TA  85 °C or 3.0 V to 3.6 V and –40 °C  TA  85 °C, respectively. Typical parameters apply to 5 V or 3.3 V at 25 °C and
are for design guidance only.
Table 19. DC I2C Specifications
Min
Typ
Max
Units
VILI2C[14]
Parameter
Input low level
Description
–
–
0.3 × VDD
V
Notes
–
–
0.25 × VDD
V
4.75 V  VDD 5.25 V
VIHI2C[14]
Input high level
0.7 × VDD
–
–
V
3.0 V VDD 5.25 V
3.0 V  VDD 3.6 V
Note
12. A maximum of 36 x 50,000 block endurance cycles is allowed. This may be balanced between operations on 36x1 blocks of 50,000 maximum cycles each, 36x2
blocks of 25,000 maximum cycles each, or 36x4 blocks of 12,500 maximum cycles each (to limit the total number of cycles to 36x50,000 and that no single block
ever sees more than 50,000 cycles).
For the full industrial range, the user must employ a temperature sensor user module (FlashTemp) and feed the result to the temperature argument before writing.
Refer to the Flash APIs Application Note AN2015 at http://www.cypress.com under Application Notes for more information.
13. The 50,000 cycle Flash endurance per block is guaranteed only if the Flash operates within one voltage range. Voltage ranges are 3.0 V to 3.6 V and 4.75 V to 5.25 V
14. All GPIOs meet the DC GPIO VIL and VIH specifications found in the DC GPIO specifications sections.The I2C GPIO pins also meet the above specs.
Document Number: 001-43084 Rev. *V
Page 20 of 40
CY8C21345
CY8C22345
CY8C22545
AC Electrical Characteristics
AC Chip Level Specifications
The following tables list the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to
5.25 V and –40 °C  TA  85 °C or 3.0 V to 3.6 V and –40 °C  TA  85 °C, respectively. Typical parameters apply to 5 V or 3.3 V at
25 °C and are for design guidance only.
Table 20. 5 V and 3.3 V AC Chip-Level Specifications
Symbol
FIMO24 [15]
Description
Internal Main Oscillator
Frequency for 24 MHz
tjit_PLL [20]
24 MHz IMO cycle-to-cycle
jitter (RMS)
24 MHz IMO long term N
cycle-to-cycle jitter (RMS)
24 MHz IMO period jitter (RMS)
Min
22.8
Min(%) Typ
Max
Max(%) Units
Notes
–
24 25.2 [16, 17, 18]
–
MHz Trimmed for 5 V or 3.3 V operation
using factory trim values. See Figure
5 on page 13. SLIMO mode = 0 < 85.
FIMO6
Internal Main Oscillator
5.5
6
MHz Trimmed for 5 V or 3.3 V operation
8
6.5 [16, 17, 18]
8
Frequency for 6 MHz
using factory trim values. See Figure
5 on page 13. SLIMO mode = 0 < 85.
[16, 17]
FCPU1
CPU Frequency (5 V Nominal) 0.089
–
24
–
MHz
24 MHz only for
24.6
SLIMO mode = 0.
[17,
18]
FCPU2
CPU Frequency (3.3 V
0.089
–
12
–
MHz SLIMO mode = 0.
12.3
Nominal)
FBLK5
Digital PSoC Block
0
–
48 49.2 [16, 17, 19]
–
MHz Refer to Table 24 on page 23.
Frequency0(5 V Nominal)
FBLK33
Digital PSoC Block Frequency
0
–
24
–
MHz
24.6 [17, 19]
(3.3 V Nominal)
F32K1
Internal Low Speed Oscillator
15
–
32
85
–
kHz
Frequency
F32KU
Untrimmed Internal Low Speed
5
–
–
100
–
kHz The ILO is not adjusted with the
Oscillator Frequency
factory trim values until after the CPU
starts running. See the “System
Resets” section in the Technical
Reference Manual.
TXRES
External Reset Pulse Width
10
–
–
–
–
µs This specification refers to the
minimum pulse width required to
achieve complete device Reset.
Shorter pulse widths may cause
undefined chip behavior.
–
50
60
–
%
DC24M
24 MHz Duty Cycle
40
DCILO
Internal Low Speed Oscillator
20
–
50
80
–
%
Duty Cycle
FMAX
Maximum frequency of signal
–
–
–
12.3
–
MHz
on row input or row output
SRPOWERUP Power supply slew rate
–
–
–
250
–
V/ms Vdd slew rate during power up.
TPOWERUP Time from end of POR to CPU
–
–
–
100
–
ms
executing code
tjit_IMO[20] 24 MHz IMO cycle-to-cycle
–
–
200
700
–
ps
jitter (RMS)
24 MHz IMO long term N
–
–
300
900
–
ps N = 32
cycle-to-cycle jitter (RMS)
24 MHz IMO period jitter (RMS)
–
–
100
400
–
ps
–
–
200
800
–
ps
–
–
300
1200
–
ps
–
–
100
700
–
ps
N = 32
Notes
15. Errata: When the device is operated within 0 °C to 70 °C, the frequency tolerance is reduced to ±2.5%, but if operated at extreme temperature (below 0 °C or above
70 °C), frequency tolerance deviates from ±2.5% to ±5%. For more information, see “Errata” on page 35.
16. Valid only for 4.75 V < Vdd < 5.25 V.
17. Accuracy derived from Internal Main Oscillator with appropriate trim for Vdd range.
18. 3.0 V < Vdd < 3.6 V.
19. Refer to the individual user module data sheets for information on maximum frequencies for user modules.
20. Refer to Cypress Jitter Specifications, Understanding Datasheet Jitter Specifications for Cypress Timing Products for more information.
Document Number: 001-43084 Rev. *V
Page 21 of 40
CY8C21345
CY8C22345
CY8C22545
AC GPIO Specifications
Table 21 lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and
–40 °C  TA  85 °C or 3.0 V to 3.6 V and –40 °C  TA  85 °C, respectively. Typical parameters apply to 5 V or 3.3 V at 25 °C and
are for design guidance only.
Table 21. 5 V and 3.3 V AC GPIO Specifications
Symbol
Description
Min
Typ
Max
Units
Notes
FGPIO
GPIO operating frequency
0
–
12
MHz
TRiseF
Rise time, normal strong mode, Cload = 50 pF
3
–
18
ns
Normal Strong Mode
Vdd = 4.5 to 5.25 V, 10% to 90%
TFallF
Fall time, normal strong mode, Cload = 50 pF
2
–
18
ns
Vdd = 4.5 to 5.25 V, 10% to 90%
TRiseS
Rise time, slow strong mode, Cload = 50 pF
7
27
–
ns
Vdd = 3 to 5.25 V, 10% to 90%
TFallS
Fall time, slow strong mode, Cload = 50 pF
7
22
–
ns
Vdd = 3 to 5.25 V, 10% to 90%
Figure 6. GPIO Timing Diagram
90%
GPIO
Pin
Output
Voltage
10%
TRiseF
TRiseS
TFallF
TFallS
AC Operational Amplifier Specifications
Table 22 lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and
–40 °C  TA  85 °C or 3.0 V to 3.6 V and –40 °C  TA  85 °C, respectively. Typical parameters apply to 5 V or 3.3 V at 25 °C and
are for design guidance only.
Table 22. AC Operational Amplifier Specifications
Symbol
TCOMP
Description
Min
Typ
Comparator Mode Response Time, 50 mV
Max
Units
100
ns
Notes
Vdd  3.0 V
AC Low Power Comparator Specifications
Table 23 lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and
–40 °C  TA  85 °C or 3.0 V to 3.6 V and –40 °C  TA  85 °C, respectively. Typical parameters apply to 5 V at 25 °C and are for
design guidance only.
Table 23. AC Low Power Comparator Specifications
Symbol
TRLPC
Description
LPC response time
Document Number: 001-43084 Rev. *V
Min
Typ
Max
Units
–
–
50
s
Notes
 50 mV overdrive comparator
reference set within VREFLPC
Page 22 of 40
CY8C21345
CY8C22345
CY8C22545
AC Digital Block Specifications
The following tables list the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to
5.25 V and –40 °C  TA  85 °C or 3.0 V to 3.6 V and –40 °C  TA  85 °C, respectively. Typical parameters apply to 5 V or 3.3 V, at
25 °C and are for design guidance only.
Table 24. AC Digital Block Specifications
Function
All functions
Timer
Counter
Dead Band
CRCPRS
(PRS Mode)
Description
Block Input Clock Frequency
Vdd  4.75 V
Vdd < 4.75 V
Input Clock Frequency
No Capture, Vdd  4.75 V
No Capture, Vdd < 4.75 V
With Capture
Capture Pulse Width
Input Clock Frequency
No Enable Input, Vdd  4.75 V
No Enable Input, Vdd < 4.75 V
With Enable Input
Enable Input Pulse Width
Kill Pulse Width
Asynchronous Restart Mode
Synchronous Restart Mode
Disable Mode
Input Clock Frequency
Vdd  4.75 V
Vdd < 4.75 V
Input Clock Frequency
Vdd  4.75 V
Vdd < 4.75 V
Input Clock Frequency
CRCPRS
(CRC Mode)
SPIM
Input Clock Frequency
SPIS
Transmitter
Receiver
Input Clock (SCLK) Frequency
Width of SS_Negated Between Transmissions
Input Clock Frequency
Vdd  4.75 V, 2 Stop Bits
Vdd  4.75 V, 1 Stop Bit
Vdd < 4.75 V
Input Clock Frequency
Vdd  4.75 V, 2 Stop Bits
Vdd  4.75 V, 1 Stop Bit
Vdd < 4.75 V
Min
Typ
Max
Units
Notes
–
–
–
–
50.4[21]
25.2[21]
MHz
MHz
–
–
–
–
–
–
50.4[21]
25.2[21]
25.2[21]
MHz
MHz
MHz
50[22]
–
–
ns
–
–
–
50[22]
–
–
–
–
50.4[21]
25.2[21]
25.2[21]
–
MHz
MHz
MHz
ns
20
50[22]
50[22]
–
–
–
–
–
–
ns
ns
ns
–
–
–
–
50.4[21]
25.2[21]
MHz
MHz
–
–
–
–
–
–
50.4[21]
25.2[21]
25.2[21]
MHz
MHz
MHz
–
–
8.4[21]
MHz The SPI serial clock (SCLK)
frequency is equal to the input
clock frequency divided by 2.
–
–
4.2[21]
50[22]
–
–
–
–
–
–
–
–
50.4[21]
25.2[21]
25.2[21]
–
–
–
–
–
–
50.4[21]
25.2[21]
25.2[21]
MHz The input clock is the SPI SCLK in
SPIS mode.
ns
The baud rate is equal to the input
MHz clock frequency divided by 8.
MHz
MHz
The baud rate is equal to the input
MHz clock frequency divided by 8.
MHz
MHz
Notes
21. Accuracy derived from IMO with appropriate trim for VDD range.
22. 50 ns minimum input pulse width is based on the input synchronizers running at 24 MHz (42 ns nominal period).
Document Number: 001-43084 Rev. *V
Page 23 of 40
CY8C21345
CY8C22345
CY8C22545
AC External Clock Specifications
The following tables list the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to
5.25 V and –40 °C  TA  85 °C, or 3.0 V to 3.6 V and –40 °C  TA  85 °C, respectively. Typical parameters apply to 5 V or 3.3 V at
25 °C and are for design guidance only.
Table 25. 5 V AC External Clock Specifications
Symbol
Description
Min
Typ
Max
Units
FOSCEXT
Frequency
0.093
–
24.6
MHz
–
High Period
20.6
–
5300
ns
–
Low Period
20.6
–
–
ns
–
Power Up IMO to Switch
150
–
–
s
Notes
Table 26. 3.3 V AC External Clock Specifications
Min
Typ
Max
Units
FOSCEXT
Symbol
Frequency with CPU Clock divide by 1
Description
0.093
–
12.3
MHz Maximum CPU frequency is
12 MHz at 3.3 V. With the CPU
clock divider set to 1, the
external clock must adhere to
the maximum frequency and
duty cycle requirements.
Notes
FOSCEXT
Frequency with CPU Clock divide by 2 or greater
0.186
–
24.6
MHz If the frequency of the external
clock is greater than 12 MHz,
the CPU clock divider must be
set to 2 or greater. In this case,
the CPU clock divider ensures
that the fifty percent duty cycle
requirement is met.
–
High Period with CPU Clock divide by 1
41.7
–
5300
ns
–
Low Period with CPU Clock divide by 1
41.7
–
–
ns
–
Power Up IMO to Switch
150
–
–
s
SAR10 ADC AC Specifications
Table 27 lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and
–40 °C  TA  85 °C, or 3.0 V to 3.6 V and –40 °C  TA  85 °C, respectively. Typical parameters apply to 5 V and 3.3 V at 25 °C and
are for design guidance only.
Table 27. SAR10 ADC AC Specifications
Symbol
Description
Min
Typ
Max
Units
Freq3
Input clock frequency 3 V
–
–
2.7
MHz
Freq5
Input clock frequency 5 V
–
–
2.7
MHz
Document Number: 001-43084 Rev. *V
Notes
Page 24 of 40
CY8C21345
CY8C22345
CY8C22545
AC Programming Specifications
Table 28 lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and
–40 °C  TA  85 °C, or 3.0 V to 3.6 V and –40 °C  TA  85 °C, respectively. Typical parameters apply to 5 V, or 3.3 V at 25 °C and
are for design guidance only.
Table 28. AC Programming Specifications
Symbol
Description
Min
Typ
Max
Units
Notes
TRSCLK
Rise Time of SCLK
1
–
20
ns
TFSCLK
Fall Time of SCLK
1
–
20
ns
TSSCLK
Data Set up Time to Falling Edge of SCLK
40
–
–
ns
THSCLK
Data Hold Time from Falling Edge of SCLK
40
–
–
ns
FSCLK
Frequency of SCLK
0
–
8
MHz
FSCLK3
Frequency of SCLK3
0
–
6
MHz VDD < 3.6 V
TERASEB
Flash Erase Time (Block)
–
10
–
ms
TWRITE
Flash Block Write Time
–
40
–
ms
TDSCLK
Data Out Delay from Falling Edge of SCLK
–
–
55
ns
3.6 < Vdd; at 30 pF Load
TDSCLK3
Data Out Delay from Falling Edge of SCLK
–
–
65
ns
3.0 Vdd 3.6; at 30 pF Load
TERASEALL
Flash Erase Time (Bulk)
–
40
–
ns
TPROGRAM_HOT
Flash Block Erase + Flash Block Write Time
–
–
100
ms
TPROGRAM_COLD Flash Block Erase + Flash Block Write Time
–
–
200
ms
Document Number: 001-43084 Rev. *V
Page 25 of 40
CY8C21345
CY8C22345
CY8C22545
AC I2C Specifications
Table 29 lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and
–40 °C  TA  85 °C, and 3.0 V to 3.6 V and –40 °C  TA  85 °C, respectively. Typical parameters apply to 5 V, 3.3 V, or 2.7 V at
25 °C and are for design guidance only.
Table 29. AC Characteristics of the I2C SDA and SCL Pins for Vdd 3.0 V
Symbol
Standard Mode
Description
Fast Mode
Units
Min
Max
Min
Max
0
100
0
400
kHz
FSCLI2C
SCL Clock Frequency
THDSTAI2C
Hold Time (repeated) START Condition.
After this period, the first clock pulse is
generated.
4.0
–
0.6
–
s
TLOWI2C
LOW Period of the SCL Clock
4.7
–
1.3
–
s
THIGHI2C
HIGH Period of the SCL Clock
4.0
–
0.6
–
s
TSUSTAI2C
Setup Time for a Repeated START
Condition
4.7
–
0.6
–
s
THDDATI2C
Data Hold Time
0
–
0
–
s
TSUDATI2C
Data Setup Time
250
–
100[23]
–
ns
TSUSTOI2C
Setup Time for STOP Condition
4.0
–
0.6
–
s
TBUFI2C
Bus Free Time Between a STOP and
START Condition
4.7
–
1.3
–
s
TSPI2C
Pulse Width of spikes are suppressed by the
Input Filter
–
–
0
50
ns
Notes
Figure 7. Definition for Timing for Fast/Standard Mode on the I2C Bus
I2C_SDA
TSUDATI2C
THDSTAI2C
TSPI2C
THDDATI2CTSUSTAI2C
TBUFI2C
I2C_SCL
THIGHI2C TLOWI2C
S
START Condition
TSUSTOI2C
Sr
Repeated START Condition
P
S
STOP Condition
Note
23. A Fast-Mode I2C-bus device may be used in a Standard-Mode I2C-bus system, but the requirement TSUDATI2C  250 ns must then be met. This is automatically the
case if the device does not stretch the LOW period of the SCL signal. If such device does stretch the LOW period of the SCL signal, it must output the next data bit
to the SDA line trmax + TSUDATI2C = 1000 + 250 = 1250 ns (according to the Standard-Mode I2C-bus specification) before the SCL line is released.
Document Number: 001-43084 Rev. *V
Page 26 of 40
CY8C21345
CY8C22345
CY8C22545
Packaging Information
Figure 8. 28-pin SOIC (0.713 × 0.300 × 0.0932 Inches) Package Outline, 51-85026
51-85026 *H
Figure 9. 44-pin TQFP (10 × 10 × 1.4 mm) A44S Package Outline, 51-85064
51-85064 *F
Document Number: 001-43084 Rev. *V
Page 27 of 40
CY8C21345
CY8C22345
CY8C22545
Thermal Impedances
Table 30. Thermal Impedances per Package
Package
Typical JA [25]
28-pin SOIC
68 °C/W
44-pin TQFP
61 °C/W
Solder Reflow Specifications
Table 31 shows the solder reflow temperature limits that must not be exceeded.
Table 31. Solder Reflow Specifications
Package
Maximum Peak Temperature
(TC)
Maximum Time above TC – 5 °C
28-pin SOIC
260 °C
30 seconds
44-pin TQFP
260 °C
30 seconds
Ordering Information
The following table lists the key package features and ordering codes of this PSoC device family.
4
28-pin SOIC (Tape and Reel)
CY8C21345-24SXIT
8
512B
28-pin SOIC
CY8C22345-24SXI
16
1K
XRES Pin
–40 °C to +85 °C
Analog Outputs
512B
Analog Inputs
8
Digital I/O Pins
Digital Blocks
(Rows of 4)
CY8C21345-24SXI
Analog Blocks
(Columns of 3)
Temperature
Range
28-pin SOIC
Ordering Code
RAM (Bytes)
Package
Flash (Kbytes)
Table 32. PSoC Device Family Key Features and Ordering Information
6
24
24[24]
0
Y
–40 °C to +85 °C
4
6
24
24[24]
0
Y
–40 °C to +85 °C
8
6
24
24[24]
0
Y
28-pin SOIC (Tape and Reel)
CY8C22345-24SXIT
16
1K
–40 °C to +85 °C
8
6
24
24[24]
0
Y
44-pin TQFP
CY8C22545-24AXI
16
1K
–40 °C to +85 C
8
6
38
38[24]
0
Y
38
[24]
0
Y
44-pin TQFP (Tape and Reel)
CY8C22545-24AXIT
16
1K
–40 °C to +85 C
8
6
38
Ordering Code Definitions
CY 8 C 2x xxx-SPxx
Package Type:
PX = PDIP Pb-free
SX = SOIC Pb-free
PVX = SSOP Pb-free
LFX/LTX = QFN Pb-free
AX = TQFP Pb-free
Thermal Rating:
C = Commercial
I = Industrial
E = Extended
CPU Speed: 24 MHz
Part Number
Family Code (21, 22)
Technology Code: C = CMOS
Marketing Code: 8 = PSoC
Company ID: CY = Cypress
Note
24. Ten direct inputs.
25. TJ = TA + POWER x JA
Document Number: 001-43084 Rev. *V
Page 28 of 40
CY8C21345
CY8C22345
CY8C22545
Acronyms
Table 33 lists the acronyms that are used in this document.
Table 33. Acronyms Used in this Datasheet
Acronym
AC
Description
Acronym
Description
alternating current
MAC
multiply-accumulate
ADC
analog-to-digital converter
MCU
microcontroller unit
API
application programming interface
MIPS
million instructions per second
CMOS
complementary metal oxide semiconductor
PCB
printed circuit board
CPU
central processing unit
PGA
programmable gain amplifier
CRC
cyclic redundancy check
PLL
phase-locked loop
CSD
CapSense sigma delta
POR
power on reset
CT
continuous time
PPOR
precision power on reset
DAC
digital-to-analog converter
PRS
pseudo-random sequence
DC
direct current
PSoC®
Programmable System-on-Chip
DNL
differential nonlinearity
PWM
pulse width modulator
ECO
external crystal oscillator
QFN
quad flat no leads
EEPROM
electrically erasable programmable read-only
memory
RTC
real time clock
FSK
frequency-shift keying
SAR
successive approximation
GPIO
general-purpose I/O
SC
switched capacitor
I/O
input/output
SLIMO
slow IMO
ICE
in-circuit emulator
SOIC
small-outline integrated circuit
IDE
integrated development environment
SPI™
serial peripheral interface
IDAC
current DAC
SRAM
static random access memory
ILO
internal low speed oscillator
SROM
supervisory read only memory
IMO
internal main oscillator
SSOP
shrink small-outline package
INL
integral nonlinearity
TQFP
thin quad flat pack
IrDA
infrared data association
UART
universal asynchronous receiver / transmitter
ISSP
in-system serial programming
USB
universal serial bus
LPC
low power comparator
WDT
watchdog timer
LSB
least-significant bit
XRES
external reset
LVD
low voltage detect
Reference Documents
CY8C22x45 and CY8C21345 PSoC® Programmable System-on-Chip™ Technical Reference Manual (TRM) (001-48461)
Design Aids – Reading and Writing PSoC® Flash – AN2015 (001-40459)
Understanding Datasheet Jitter Specifications for Cypress Timing Products
Document Number: 001-43084 Rev. *V
Page 29 of 40
CY8C21345
CY8C22345
CY8C22545
Document Conventions
Units of Measure
Table 34 lists the units of measures.
Table 34. Units of Measure
Symbol
Unit of Measure
Symbol
Unit of Measure
kB
1024 bytes
mV
millivolts
C
degree Celsius
nA
nanoampere
kilohertz
ns
nanosecond
kHz
k
LSB
MHz
kilohm
W
ohm
least significant bit
%
percent
megahertz
pF
picofarad
microampere
ps
picosecond
µs
microsecond
sps
samples per second
µV
microvolt
pA
pikoampere
V
volts
µA
mA
milliampere
mm
millimeter
µW
microwatts
ms
millisecond
W
watt
Numeric Conventions
Hexadecimal numbers are represented with all letters in uppercase with an appended lowercase ‘h’ (for example, ‘14h’ or ‘3Ah’).
Hexadecimal numbers may also be represented by a ‘0x’ prefix, the C coding convention. Binary numbers have an appended
lowercase ‘b’ (for example, 01010100b’ or ‘01000011b’). Numbers not indicated by an ‘h’ or ‘b’ are decimals.
Glossary
active high
1. A logic signal having its asserted state as the logic 1 state.
2. A logic signal having the logic 1 state as the higher voltage of the two states.
analog blocks
The basic programmable opamp circuits. These are SC (switched capacitor) and CT (continuous time) blocks.
These blocks can be interconnected to provide ADCs, DACs, multi-pole filters, gain stages, and much more.
analog-to-digital
(ADC)
A device that changes an analog signal to a digital signal of corresponding magnitude. Typically, an ADC converts
a voltage to a digital number. The digital-to-analog (DAC) converter performs the reverse operation.
API (Application
Programming
Interface)
A series of software routines that comprise an interface between a computer application and lower level services
and functions (for example, user modules and libraries). APIs serve as building blocks for programmers that
create software applications.
asynchronous
A signal whose data is acknowledged or acted upon immediately, irrespective of any clock signal.
bandgap
reference
A stable voltage reference design that matches the positive temperature coefficient of VT with the negative
temperature coefficient of VBE, to produce a zero temperature coefficient (ideally) reference.
bandwidth
1. The frequency range of a message or information processing system measured in hertz.
2. The width of the spectral region over which an amplifier (or absorber) has substantial gain (or loss); it is
sometimes represented more specifically as, for example, full width at half maximum.
Document Number: 001-43084 Rev. *V
Page 30 of 40
CY8C21345
CY8C22345
CY8C22545
Glossary (continued)
bias
1. A systematic deviation of a value from a reference value.
2. The amount by which the average of a set of values departs from a reference value.
3. The electrical, mechanical, magnetic, or other force (field) applied to a device to establish a reference level to
operate the device.
block
1. A functional unit that performs a single function, such as an oscillator.
2. A functional unit that may be configured to perform one of several functions, such as a digital PSoC block or
an analog PSoC block.
buffer
1. A storage area for data that is used to compensate for a speed difference, when transferring data from one
device to another. Usually refers to an area reserved for IO operations, into which data is read, or from which
data is written.
2. A portion of memory set aside to store data, often before it is sent to an external device or as it is received
from an external device.
3. An amplifier used to lower the output impedance of a system.
bus
1. A named connection of nets. Bundling nets together in a bus makes it easier to route nets with similar routing
patterns.
2. A set of signals performing a common function and carrying similar data. Typically represented using vector
notation; for example, address[7:0].
3. One or more conductors that serve as a common connection for a group of related devices.
clock
The device that generates a periodic signal with a fixed frequency and duty cycle. A clock is sometimes used to
synchronize different logic blocks.
comparator
An electronic circuit that produces an output voltage or current whenever two input levels simultaneously satisfy
predetermined amplitude requirements.
compiler
A program that translates a high level language, such as C, into machine language.
configuration
space
In PSoC devices, the register space accessed when the XIO bit, in the CPU_F register, is set to ‘1’.
crystal oscillator
An oscillator in which the frequency is controlled by a piezoelectric crystal. Typically a piezoelectric crystal is less
sensitive to ambient temperature than other circuit components.
cyclic redundancy A calculation used to detect errors in data communications, typically performed using a linear feedback shift
check (CRC)
register. Similar calculations may be used for a variety of other purposes such as data compression.
data bus
A bi-directional set of signals used by a computer to convey information from a memory location to the central
processing unit and vice versa. More generally, a set of signals used to convey data between digital functions.
debugger
A hardware and software system that allows the user to analyze the operation of the system under development.
A debugger usually allows the developer to step through the firmware one step at a time, set break points, and
analyze memory.
dead band
A period of time when neither of two or more signals are in their active state or in transition.
digital blocks
The 8-bit logic blocks that can act as a counter, timer, serial receiver, serial transmitter, CRC generator,
pseudo-random number generator, or SPI.
digital-to-analog
(DAC)
A device that changes a digital signal to an analog signal of corresponding magnitude. The analog-to-digital (ADC)
converter performs the reverse operation.
Document Number: 001-43084 Rev. *V
Page 31 of 40
CY8C21345
CY8C22345
CY8C22545
Glossary (continued)
duty cycle
The relationship of a clock period high time to its low time, expressed as a percent.
emulator
Duplicates (provides an emulation of) the functions of one system with a different system, so that the second
system appears to behave like the first system.
external reset
(XRES)
An active high signal that is driven into the PSoC device. It causes all operation of the CPU and blocks to stop
and return to a pre-defined state.
flash
An electrically programmable and erasable, non-volatile technology that provides users with the programmability
and data storage of EPROMs, plus in-system erasability. Non-volatile means that the data is retained when power
is off.
Flash block
The smallest amount of Flash ROM space that may be programmed at one time and the smallest amount of Flash
space that may be protected. A Flash block holds 64 bytes.
frequency
The number of cycles or events per unit of time, for a periodic function.
gain
The ratio of output current, voltage, or power to input current, voltage, or power, respectively. Gain is usually
expressed in dB.
I2C
A two-wire serial computer bus by Philips Semiconductors (now NXP Semiconductors). I2C is an Inter-Integrated
Circuit. It is used to connect low-speed peripherals in an embedded system. The original system was created in
the early 1980s as a battery control interface, but it was later used as a simple internal bus system for building
control electronics. I2C uses only two bi-directional pins, clock and data, both running at +5 V and pulled high
with resistors. The bus operates at 100 kbits/second in standard mode and 400 kbits/second in fast mode.
ICE
The in-circuit emulator that allows users to test the project in a hardware environment, while viewing the debugging
device activity in a software environment (PSoC Designer).
input/output (I/O) A device that introduces data into or extracts data from a system.
interrupt
A suspension of a process, such as the execution of a computer program, caused by an event external to that
process, and performed in such a way that the process can be resumed.
interrupt service
routine (ISR)
A block of code that normal code execution is diverted to when the M8C receives a hardware interrupt. Many
interrupt sources may each exist with its own priority and individual ISR code block. Each ISR code block ends
with the RETI instruction, returning the device to the point in the program where it left normal program execution.
jitter
1. A misplacement of the timing of a transition from its ideal position. A typical form of corruption that occurs on
serial data streams.
2. The abrupt and unwanted variations of one or more signal characteristics, such as the interval between
successive pulses, the amplitude of successive cycles, or the frequency or phase of successive cycles.
low-voltage
detect (LVD)
A circuit that senses Vdd and provides an interrupt to the system when Vdd falls below a selected threshold.
M8C
An 8-bit Harvard-architecture microprocessor. The microprocessor coordinates all activity inside a PSoC by
interfacing to the Flash, SRAM, and register space.
master device
A device that controls the timing for data exchanges between two devices. Or when devices are cascaded in
width, the master device is the one that controls the timing for data exchanges between the cascaded devices
and an external interface. The controlled device is called the slave device.
Document Number: 001-43084 Rev. *V
Page 32 of 40
CY8C21345
CY8C22345
CY8C22545
Glossary (continued)
microcontroller
An integrated circuit chip that is designed primarily for control systems and products. In addition to a CPU, a
microcontroller typically includes memory, timing circuits, and IO circuitry. The reason for this is to permit the
realization of a controller with a minimal quantity of chips, thus achieving maximal possible miniaturization. This
in turn, reduces the volume and the cost of the controller. The microcontroller is normally not used for
general-purpose computation as is a microprocessor.
mixed-signal
The reference to a circuit containing both analog and digital techniques and components.
modulator
A device that imposes a signal on a carrier.
noise
1. A disturbance that affects a signal and that may distort the information carried by the signal.
2. The random variations of one or more characteristics of any entity such as voltage, current, or data.
oscillator
A circuit that may be crystal controlled and is used to generate a clock frequency.
parity
A technique for testing transmitting data. Typically, a binary digit is added to the data to make the sum of all the
digits of the binary data either always even (even parity) or always odd (odd parity).
phase-locked
loop (PLL)
An electronic circuit that controls an oscillator so that it maintains a constant phase angle relative to a reference
signal.
pinouts
The pin number assignment: the relation between the logical inputs and outputs of the PSoC device and their
physical counterparts in the printed circuit board (PCB) package. Pinouts involve pin numbers as a link between
schematic and PCB design (both being computer generated files) and may also involve pin names.
port
A group of pins, usually eight.
power on reset
(POR)
A circuit that forces the PSoC device to reset when the voltage is below a pre-set level. This is one type of hardware
reset.
PSoC®
Cypress Semiconductor’s PSoC® is a registered trademark and Programmable System-on-Chip™ is a trademark
of Cypress.
PSoC Designer™ The software for Cypress’ Programmable System-on-Chip technology.
pulse width
An output in the form of duty cycle which varies as a function of the applied measurand.
modulator (PWM)
RAM
An acronym for random access memory. A data-storage device from which data can be read out and new data
can be written in.
register
A storage device with a specific capacity, such as a bit or byte.
reset
A means of bringing a system back to a know state. See hardware reset and software reset.
ROM
An acronym for read only memory. A data-storage device from which data can be read out, but new data cannot
be written in.
serial
1. Pertaining to a process in which all events occur one after the other.
2. Pertaining to the sequential or consecutive occurrence of two or more related activities in a single device or
channel.
settling time
The time it takes for an output signal or value to stabilize after the input has changed from one value to another.
Document Number: 001-43084 Rev. *V
Page 33 of 40
CY8C21345
CY8C22345
CY8C22545
Glossary (continued)
shift register
A memory storage device that sequentially shifts a word either left or right to output a stream of serial data.
slave device
A device that allows another device to control the timing for data exchanges between two devices. Or when
devices are cascaded in width, the slave device is the one that allows another device to control the timing of data
exchanges between the cascaded devices and an external interface. The controlling device is called the master
device.
SRAM
An acronym for static random access memory. A memory device allowing users to store and retrieve data at a
high rate of speed. The term static is used because, after a value has been loaded into an SRAM cell, it remains
unchanged until it is explicitly altered or until power is removed from the device.
SROM
An acronym for supervisory read only memory. The SROM holds code that is used to boot the device, calibrate
circuitry, and perform Flash operations. The functions of the SROM may be accessed in normal user code,
operating from Flash.
stop bit
A signal following a character or block that prepares the receiving device to receive the next character or block.
synchronous
1. A signal whose data is not acknowledged or acted upon until the next active edge of a clock signal.
2. A system whose operation is synchronized by a clock signal.
tri-state
A function whose output can adopt three states: 0, 1, and Z (high-impedance). The function does not drive any
value in the Z state and, in many respects, may be considered to be disconnected from the rest of the circuit,
allowing another output to drive the same net.
UART
A UART or universal asynchronous receiver-transmitter translates between parallel bits of data and serial bits.
user modules
Pre-build, pre-tested hardware/firmware peripheral functions that take care of managing and configuring the lower
level Analog and Digital PSoC Blocks. User Modules also provide high level API (Application Programming
Interface) for the peripheral function.
user space
The bank 0 space of the register map. The registers in this bank are more likely to be modified during normal
program execution and not just during initialization. Registers in bank 1 are most likely to be modified only during
the initialization phase of the program.
VDD
A name for a power net meaning “voltage drain.” The most positive power supply signal. Usually 5 V or 3.3 V.
VSS
A name for a power net meaning “voltage source.” The most negative power supply signal.
watchdog timer
A timer that must be serviced periodically. If it is not serviced, the CPU resets after a specified period of time.
Document Number: 001-43084 Rev. *V
Page 34 of 40
CY8C21345
CY8C22345
CY8C22545
Errata
This section describes the errata for the CY8C21x45, CY8C22x45 family of PSoC devices. Details include errata trigger conditions,
scope of impact, available workaround, and silicon revision applicability.
Contact your local Cypress Sales Representative if you have questions.
Part Numbers Affected
Part Number
Device Characteristics
CY8C21345
All Variants
CY8C22345
All Variants
CY8C22545
All Variants
CY8C21x45, CY8C22x45 Qualification Status
Product Status: In Production
Errata Summary
The following table defines the errata applicable for this PSoC family device.
Items
Part Number
Silicon Revision
Fix Status
1. Free Running Nonstop Reading
All CY8C21x45, CY8C22x45
cause 7 LSB Pseudo Code Variation devices affected
in SAR10ADC
All
Silicon fix not planned. Use
workaround.
2. Internal Main Oscillator (IMO)
All CY8C21x45, CY8C22x45
Tolerance Deviation at Temperature devices affected
Extremes
All
Silicon fix not planned. Use
workaround.
1. Free Running Nonstop Reading cause 7 LSB Pseudo Code Variation in SAR10ADC
■
Problem Definition
In free running mode, there can be a variation of up to 7 LSB in the digital output of SAR10 ADC.
■
Parameters Affected
Code Variation. This is not a specified parameter.
It is defined as the number of unique output codes generated by the ADC for a given constant input voltage, in addition to the correct
code. For example, for an input voltage of 2.000 V, the expected code is 190hex and the ADC generates three codes: 191hex, 190hex,
and 192hex. The code variation is 2 LSB.
■
Trigger Condition(S)
SAR10 ADC is configured in the free running mode. When ADC is operated in free running mode, for a constant input voltage output
of ADC can have a variation of up to 7LSB. This can be resolved by using the averaging technique or by disabling the free running
mode before reading the data and enabling again after reading the data.
■
Scope of Impact
Inaccurate output is possible.
■
Workaround
This issue can be averted by using one or both of the following workarounds. Consult a Cypress representative for additional
assistance.
❐ Use the averaging technique. That is, take multiple samples of the input, and use a digital averaging filter.
❐ Disable the free running mode before reading data out, and enable the free running mode after completing the read operation.
■
Fix Status
No silicon fix is planned.
Document Number: 001-43084 Rev. *V
Page 35 of 40
CY8C21345
CY8C22345
CY8C22545
2. Internal Main Oscillator (IMO) Tolerance Deviation at Temperature Extremes
■
Problem Definition
Asynchronous Digital Communications Interfaces may fail framing beyond 0 to 70 °C. This problem does not affect end-product usage
between 0 and 70 °C.
■
Parameters Affected
The IMO frequency tolerance. The worst case deviation when operated below 0 °C and above +70 °C and within the upper and lower
datasheet temperature range is ±5%.
■
Trigger Condiiton(S)
The asynchronous Rx/Tx clock source IMO frequency tolerance may deviate beyond the datasheet limit of ±2.5% when operated
beyond the temperature range of 0 to +70 °C.
■
Scope of Impact
This problem may affect UART, IrDA, and FSK implementations.
■
Workaround
Implement a quartz crystal stabilized clock source on at least one end of the asynchronous digital communications interface.
■
Fix Status
The cause of this problem and its solution has been identified. No silicon fix is planned to correct the deficiency in silicon.
Document Number: 001-43084 Rev. *V
Page 36 of 40
CY8C21345
CY8C22345
CY8C22545
Document History Page
Document Title: CY8C21345/CY8C22345/CY8C22545, PSoC® Programmable System-on-Chip
Document Number: 001-43084
Revision
ECN
Orig. of
Change
Submission
Date
**
2251907
PMP /
AESA
See ECN
New data sheet.
*A
2506377
EIJ / AESA
See ECN
Changed data sheet status to “Preliminary”. Changed part numbers to
CY8C22x45. Updated data sheet template.
Added 56-Pin OCD information. Added: “You must put filters on intended ADC
input channels for anti-aliasing. This ensures that any out-of-band content is
not folded into the Input Signal Band." To Section Analog System on page 4.
Corrected Minimum Electro Static Discharge Voltage in Table 7 on page 14.
*B
2558750
PMP /
AESA
08/28/2008
Updated Features on page 1, PSoC Core on page 3, Analog System on page 4.
Changed DBB to DBC, and DCB to DCC in Register Tables Table 5 on page
11 and Table 6 on page 12.
Removed INL at 8 bit reference in Table 15 on page 18.
Changed IDD3 value Table 17 on page 19 Typ:3.3 mA, Max 6 mA
Added “3.0 V < Vdd < 3.6 V and -40C < TA < 85C, IMO can guarantee 5%
accuracy only” to Table 20 on page 21.
Updated data sheet template.
*C
2606793
NUQ /
AESA
11/19/2008
Updated data sheet status to “Final”. Updated block diagram on page 1.
Removed CY8C22045 56-Pin OCD information. Added part numbers
CY8C21345, CY8C22345, and CY8C22545. For more details, see CDT
31271.
*D
2615697
PMP /
AESA
12/03/2008
Confirmed CY8C22345 and CY8C21345 have same pinout on page 8.
Confirmed that IMO has 5% accuracy in Table 20 on page 21.
*E
2631733
PMP /
PYRS
01/07/2009
Updated Table 16. SAR10 ADC DC Specifications and Table 29 AC
Programming Specifications. Title changed to “CY8C21345, CY8C22345,
CY8C22545 PSoC® Programmable System-on-Chip™”
*F
2648800
JHU /
AESA
01/28/2009
Updated INL, DNL information in Table 15 on page 18, Development Tools on
page 6, and TDSCLK parameter in Table 28 on page 25.
*G
2658078
HMI /
AESA
02/11/2009
Updated section Features on page 1.
*H
2667311
JHU /
AESA
03/16/2009
Added parameter “F32KU” and added Min% and Max % to parameter “FIMO6”
in Table 20 on page 21, according to updated SLIMO spec.
*I
2748976
JZHU /
PYRS
08/06/2009
Updated F32K1 max rating in Table 20 on page 21.
*J
2786560
JZHU
10/23/2009
Added DCILO, TERASEALL, TPROGRAM_HOT, TPROGRAM_COLD, SRPOWERUP,
IOH, and IOL parameters.
Added Tape and Reel parts in Ordering Information table
*K
2901653
NJF
03/30/2010
Updated PSoC Designer Software Subsystems.
Added TBAKETEMP and TBAKETIME parameters in Absolute Maximum Ratings
Modified Note 6 on page 17.
Added FOUT48M parameter in 5 V and 3.3 V AC Chip-Level Specifications.
Removed AC Analog Mux Bus Specifications.
Updated Ordering Code Definitions.
Updated links in Sales, Solutions, and Legal Information.
*L
3114978
NJF
12/19/10
Document Number: 001-43084 Rev. *V
Description of Change
Added DC I2C Specifications.
Added Tjit_IMO specification, removed existing jitter specifications.
Updated DC Programming Specifications.
Updated AC Digital Block Specifications.
Updated I2C Timing Diagram.
Added Solder Reflow Peak Temperature table.
Updated Units of Measure, Acronyms, Glossary, and References sections.
Page 37 of 40
CY8C21345
CY8C22345
CY8C22545
Document History Page (continued)
Document Title: CY8C21345/CY8C22345/CY8C22545, PSoC® Programmable System-on-Chip
Document Number: 001-43084
Revision
ECN
Orig. of
Change
Submission
Date
Description of Change
*M
3231771
BOBH /
ECU
04/18/11
Updated analog inputs column in Table 32 on page 28 and included reference
to Note 24.
Updated the following sections: Getting Started, Development Tools, and
Designing with PSoC Designer as all the System level designs have been
de-emphasized.
Updated Table 31, “Solder Reflow Specifications,” on page 28.
Updated package diagrams:
51-85026 to *F
51-85064 to *E
*N
3578757
PMAD
04/11/2012
Removed reference to AN2012 as the document is in obsolete status.
Updated template.
No technical updates. Completing sunset review.
*O
3598230
LURE /
XZNG
04/24/2012
Changed the PWM description string from “8- to 32-bit” to “8- and 16-bit”.
*P
3915358
SAMP
02/27/2013
Updated Electrical Specifications (Updated DC Electrical Characteristics
(Updated DC GPIO Specifications (Updated Table 10 (Updated Notes for VOH
and VOL parameters)))).
*Q
3959550
SAMP
04/09/2013
Added Errata.
*R
4081559
PMAD
07/30/2013
Added Errata footnotes (Note 1, 11, 15).
Updated Features:
Added Note 1 and referred the same note in +5% under “Precision,
programmable clocking”.
Updated Electrical Specifications:
Updated DC Electrical Characteristics:
Updated SAR10 ADC DC Specifications:
Added Note 11 and referred the same note in SPS parameter.
Updated AC Electrical Characteristics:
Updated AC Chip Level Specifications:
Added Note 15 and referred the same note in FIMO24 parameter.
Updated Packaging Information:
spec 51-85026 – Changed revision from *F to *G.
Updated Errata.
Updated in new template.
*S
4416752
RAHU
06/26/2014
Updated Pinouts:
Updated CY8C22345, CY8C21345 28-pin SOIC:
Updated Note 6.
Updated CY8C22545 44-pin TQFP:
Updated Table 3:
Replaced “TC” with “ISSP” in description of pin 16 and pin 18.
Updated Packaging Information:
spec 51-85026 – Changed revision from *G to *H.
spec 51-85064 – Changed revision from *E to *F.
Document Number: 001-43084 Rev. *V
Page 38 of 40
CY8C21345
CY8C22345
CY8C22545
Document History Page (continued)
Document Title: CY8C21345/CY8C22345/CY8C22545, PSoC® Programmable System-on-Chip
Document Number: 001-43084
Revision
ECN
Orig. of
Change
Submission
Date
*T
4473295
MSUR
08/13/2014
Description of Change
Updated Getting Started:
Updated description.
Updated Application Notes:
Updated description.
Updated Development Kits:
Updated description.
Updated Electrical Specifications:
Updated DC Electrical Characteristics:
Updated DC GPIO Specifications:
Updated Table 10:
Added Note 9 and referred the same note in Table 10.
Updated AC Electrical Characteristics:
Updated AC Chip Level Specifications:
Updated Table 20:
Renamed TXRST as TXRES and added details in “Notes” column for the same
parameter.
Removed FOUT48M parameter and its details.
*U
4515350
MSUR
09/26/2014
Updated Electrical Specifications:
Updated DC Electrical Characteristics:
Added DC IDAC Specifications.
Updated DC GPIO Specifications:
Updated Table 10:
Removed reference of Note 9 from table caption.
Referred Note 9 in RPD, VIL, VIH, VH, IIL, CIN parameters.
*V
4599794
DIMA
12/17/2014
Updated Pinouts:
Updated CY8C22345, CY8C21345 28-pin SOIC:
Updated Table 2:
Added Note 5 and referred the same note in description of pin 9 and pin 14.
Updated CY8C22545 44-pin TQFP:
Updated Table 3:
Added Note 7 and referred the same note in caption of Table 3.
Document Number: 001-43084 Rev. *V
Page 39 of 40
CY8C21345
CY8C22345
CY8C22545
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at Cypress Locations.
PSoC® Solutions
Products
Automotive
Clocks & Buffers
Interface
Lighting & Power Control
cypress.com/go/automotive
cypress.com/go/clocks
cypress.com/go/interface
cypress.com/go/powerpsoc
psoc.cypress.com/solutions
PSoC 1 | PSoC 3 | PSoC 4 | PSoC 5LP
Cypress Developer Community
Community | Forums | Blogs | Video | Training
cypress.com/go/plc
Memory
PSoC
Touch Sensing
cypress.com/go/memory
cypress.com/go/psoc
cypress.com/go/support
cypress.com/go/touch
USB Controllers
Wireless/RF
Technical Support
cypress.com/go/USB
cypress.com/go/wireless
© Cypress Semiconductor Corporation, 2008-2014. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of
any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for
medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as
critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems
application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Document Number: 001-43084 Rev. *V
Revised December 17, 2014
Page 40 of 40
PSoC Designer™ and Programmable System-on-Chip™ are trademarks and PSoC® and CapSense® are registered trademarks of Cypress Semiconductor Corporation.
Purchase of I2C components from Cypress or one of its sublicensed Associated Companies conveys a license under the Philips I2C Patent Rights to use these components in an I2C system, provided
that the system conforms to the I2C Standard Specification as defined by Philips. As from October 1st, 2006 Philips Semiconductors has a new trade name - NXP Semiconductors.
All products and company names mentioned in this document may be the trademarks of their respective holders.