Supertex inc. HV2661 Low Charge Injection 24-Channel High Voltage Analog Switch Features ►► ►► ►► ►► ►► ►► ►► ►► ►► ►► ►► ►► ►► 24-channel high voltage analog switch 3.3 or 5.0V CMOS input logic level 3:1 MUX-deMUX with 8 states 20MHz data shift clock frequency HVCMOS technology for high performance Very low quiescent power dissipation, 10µA Low parasitic capacitance DC to 50MHz analog signal frequency -60dB typical OFF-isolation at 5.0MHz CMOS logic circuitry for low power Excellent noise immunity Cascadable serial data register with latches Flexible operating supply voltages Applications ►► ►► ►► ►► Medical ultrasound imaging Piezoelectric transducer drivers Inkjet printer heads Optical MEMS modules General Description The Supertex HV2661 is a low charge injection 24-channel high voltage analog switch integrated circuit (IC) intended for use in applications requiring high voltage switching controlled by low voltage control signals, such as medical ultrasound imaging, piezoelectric transducer driver, and printers. Input data is shifted into a 24-bit shift register that can then be retained in a 24-bit latch. To reduce any possible clock feed through noise, the latch enable (LE) should be left high until all bits are clocked in. Data are clocked in during the rising edge of the clock. Using HVCMOS technology, this device combines high voltage bilateral DMOS switches and low power CMOS logic to provide efficient control of high voltage analog signals. The device is suitable for various combinations of high voltage supplies, e.g., VPP/VNN: +40V/-160V, +100V/-100V, and +160V/-40V. Block Diagram Latches D LE CLR CLK DIN 24-Bit Shift Register DOUT VDD Doc.# DSFP-HV2661 NR010913 GND LE CLR Level Shifters Output Switches SW0 D LE CLR SW1 D LE CLR SW2 D LE CLR SW3 D LE CLR SW4 D LE CLR SW5 D LE CLR SW21 D LE CLR SW22 D LE CLR SW23 Y0 Y1 Y7 VNN VPP Supertex inc. www.supertex.com HV2661 Pin Configuration Ordering Information Part Number Package Packing HV2661FG-G 48-Lead LQFP 250/Tray HV2661FG-G M931 48-Lead LQFP 1 48 1000/Reel -G indicates package is RoHS compliant (‘Green’) 48-Lead LQFP Absolute Maximum Ratings (top view) Parameter Value VDD logic supply -0.5V to +6.5V VPP-VNN differential supply VPP positive supply 220V Product Marking Top Marking YYWW -0.5V to VNN+ 200V VNN negative supply H V 2661FG LLLLLLLLL +0.5V to - 200V Logic input voltage -0.5V to VDD + 0.3V Analog signal range Bottom Marking VNN to VPP Peak analog signal current/channel Storage temperature CCCCCCCC AAA 3.0A -65°C to 150°C Power dissipation *May be part of top marking Package may or may not include the following marks: Si or 48-Lead LQFP 1.0W Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied. Continuous operation of the device at the absolute rating level may affect device reliability. All voltages are referenced to device ground. YY = Year Sealed WW = Week Sealed L = Lot Number C = Country of Origin* A = Assembler ID* = “Green” Packaging Typical Thermal Resistance Package θja 48-Lead LQFP 52OC/W Recommended Operating Conditions Sym Parameter Value VDD Logic power supply voltage 3.0V to 5.5V VPP Positive high voltage supply +40V to VNN + 200V VNN Negative high voltage supply -40V to -160V VIH High level input voltage 0.9VDD to VDD VIL Low level input voltage 0V to 0.1VDD VSIG Analog signal voltage peak-to-peak VNN +10V to VPP - 10V Operating free air temperature 0OC to 70OC TA Notes: 1. Power up/down sequence is arbitrary except GND must be powered-up first and powered-down last. 2. VSIG must be VNN ≤ VSIG ≤ VPP or floating during power up/down transition. 3. Rise and fall times of power supplies VDD, VPP, and VNN should not be less than 1.0msec. Doc.# DSFP-HV2661 NR010913 2 Supertex inc. www.supertex.com HV2661 DC Electrical Characteristics (Over recommended operating conditions unless otherwise specified ) Sym Parameter 0OC +25OC +70OC Unit Conditions Min Max Min Typ Max Min Max - - - 26 - - - - - - 22 - - - - - - 22 - - - - - - 18 - - - - - - 20 - - - - - - 16 - - - Small signal switch ON-resistance matching - 20 - 5.0 20 - 20 % RONL Large signal switch ON-resistance ISIG = 5.0mA, VPP = +100V, VNN = -100V - - - 30 - - - Ω VSIG = VPP - 10V, ISIG = 1.0A ISOL Switch OFF-leakage per switch - 5.0 - 1.0 10 - 15 μA VSIG = VPP - 10V, VNN + 10V DC offset switch OFF - 300 - 100 300 - 300 DC offset switch ON - 500 - 100 500 - 500 mV 100kΩ load IPPQ Quiescent VPP supply current - - - 10 50 - - INNQ Quiescent VNN supply current - - - -10 -50 - - μA All switches OFF IPPQ Quiescent VPP supply current - - - 10 50 - - INNQ Quiescent VNN supply current - - - -10 -50 - - μA All switches ON, ISW = 5.0mA ISW Switch output peak current - - - 2.0 1.3 - - A VSIG duty cycle < 0.1% fSW Output switching frequency - - - - 50 - - kHz Duty cycle = 50% - 4.0 - - 4.5 - 5.0 - 4.0 - - 4.5 - 5.0 mA - 4.0 - - 4.5 - 5.0 VPP= +40V, All output VNN = -160V switches are VPP= +100V, turning ON VNN = -100V and OFF at VPP= +160V, 50kHz with no load V = -40V mA VPP = +40V, All output VNN = -160V switches are VPP= +100V, turning ON VNN = -100V and OFF at VPP= +160V, 50kHz with no load V = -40V RONS ΔRONS VOS IPP Small signal switch ON-resistance Average VPP supply current ISIG = 5.0mA VPP = +40V, ISIG = 200mA VNN = -160V Ω ISIG = 5.0mA VPP = +100V, ISIG = 200mA VNN = -100V ISIG = 5.0mA VPP = +160V, ISIG = 200mA VNN = -40V NN INN Average VNN supply current - 4.0 - - 4.5 - 5.0 - 4.0 - - 4.5 - 5.0 - 4.0 - - 4.5 - 5.0 NN IDD Average VDD supply current - 8.0 - - 8.0 - 8.0 mA fCLK = 5.0MHz, VDD = 5.0V IDDQ Quiescent VDD supply current - 10 - - 10 - 10 μA All logic inputs are static ISOR Data out source current 0.45 - 0.45 0.70 - 0.40 mA VOUT = VDD - 0.7V ISINK Data out sink current 0.45 - 0.45 0.70 - 0.40 mA VOUT = 0.7V CIN Logic input capacitance - 10 10 - pF --- - - 10 * See Test Circuits on page 5 Doc.# DSFP-HV2661 NR010913 3 Supertex inc. www.supertex.com HV2661 AC Electrical Characteristics (Over recommended operating conditions unless otherwise specified) Sym Parameter tSD Set up time before LE rises tWLE Time width of LE tDO Clock delay time to data out tWCLR Time width of CLR tSU Set up time data to clock tH Hold time data from clock 0OC +25OC +70OC Min Max Min Typ Max Min Max 25 - 25 - - 25 - 56 - - 56 - 56 - 12 - - 12 - 12 - 25 100 25 78 100 25 100 15 40 15 30 40 15 40 55 - 55 - - 55 - 21 - 21 - - 21 - 7.0 - 7.0 - - 7.0 - 5.0 - 5.0 - - 5.0 - 7.0 - 7.0 - - 7.0 - - 8 - - 8 - 8 - 20 - - 20 - 20 Unit ns ns ns ns ns ns Conditions --VDD = 3.0V VDD = 5.0V VDD = 3.0V VDD = 5.0V --VDD = 3.0V VDD = 5.0V VDD = 3.0V VDD = 5.0V VDD = 3.0V fCLK Clock frequency tR, tF Clock rise and fall times - 50 - - 50 - 50 tON Turn ON time - 5.0 - - 5.0 - 5.0 tOFF Turn OFF time - 5.0 - - 5.0 - 5.0 - 20 - - 20 - 20 - 20 - - 20 - 20 - 20 - - 20 - 20 -30 - -30 -33 - -30 - -58 - -58 -60 - -58 - -60 - -60 -70 - -60 - dB f = 5.0MHz, 50Ω load Output switch isolation diode current - 300 - - 300 - 300 mA 300ns pulse width, 2.0% duty cycle OFF capacitance SW to GND - 14 - 9.0 14 - 14 OFF capacitance Y to GND - 35 - 27 35 - 35 pF VSIG = 0V, f = 1.0MHz all SW OFF ON capacitance SW to GND - 39 - 30 39 - 39 ON capacitance Y to GND - 39 - 30 39 - 39 pF VSIG = 0V, f = 1.0MHz one SW ON, two SW OFF +VSPK - - - - 150 - - -VSPK - - - - 150 - - - - - - 150 - - - - - - 150 - - +VSPK - - - - 150 - - -VSPK - - - - 150 - - dv/dt Maximum VSIG slew rate KO OFF isolation KCR Switch crosstalk IID CSG(OFF) CSG(ON) +VSPK -VSPK Output voltage spike (per switch) MHz VDD = 5.0V ns --- μs VSIG = VPP - 10V, RLOAD = 10kΩ VPP = +40V, VNN = -160V V/ns VPP = +100V, VNN = -100V VPP = +160V, VNN = -40V dB f = 5.0MHz, 1.0kΩ//15pF load f = 5.0MHz, 50Ω load VPP = +40V, VNN = -160V RLOAD = 50Ω mV VPP = +100V, VNN = -100V RLOAD = 50Ω VPP = +160V, VNN = -40V RLOAD = 50Ω * See Test Circuits on page 5 Doc.# DSFP-HV2661 NR010913 4 Supertex inc. www.supertex.com HV2661 AC Electrical Characteristics (cont.) (Over recommended operating conditions unless otherwise specified) Sym QC 0OC Parameter Charge injection (per switch) +25OC +70OC Min Max Min Typ Max Min Max - - - 820 - - - - - - 600 - - - - - - 350 - - - Unit Conditions VPP = +40V, VNN = -160V pC VPP = +100V, VNN = -100V VPP = +160V, VNN = -40V Test Circuits ISOL VPP -10V NC SW0 SW1 Y0 SW2 NC VOUT NC SW0 SW1 Y0 SW2 VPP -10V SW0 RLOAD 10kΩ VOUT NC NC SW1 NC SW2 Y0 NC 100kΩ VPP VPP VDD VNN VNN GND 5.0V VPP VPP VDD VNN VNN GND SW0 Y0 VOUT SW1 SW2 VPP VPP VDD VNN VNN GND DC Offset ON/OFF Switch OFF Leakage VIN = 10VP-P @5.0MHz 5.0V NC SW0 VSIG TON/TOFF Test Circuit SW1 NC NC IID NC VNN 50Ω NC 50Ω Y0 SW2 VOUT SW0 SW2 SW3 50Ω NC SW1 Y0 SW4 SW5 Y1 NC VPP VPP VDD VNN VNN GND KO = 20Log 5.0V VPP VPP VDD VNN VNN GND SW0 1000pF Y0 VPP VPP VDD VNN VNN GND KCR = 20Log VIN SW1 SW2 +VSPK NC VOUT SW1 SW0 +VSPK Y0 SW2 RL 1kΩ VPP VPP VDD VNN VNN GND 5.0V SW0 NC -VSPK 50Ω NC VPP VPP VDD VNN VNN GND VIN = 10VP-P @5.0MHz NC NC NC 5.0V VOUT VIN Crosstalk Isolation Diode Current ΔVOUT VOUT 5.0V VOUT OFF Isolation 5.0V NC 5.0V -VSPK RL 1kΩ VOUT Y0 SW1 SW2 NC NC 50Ω VPP VPP VDD VNN VNN GND 5.0V Q = 1000pF • ∆VOUT Charge Injection Doc.# DSFP-HV2661 NR010913 Output Voltage Spike SW 5 Output Voltage Spike Y Supertex inc. www.supertex.com HV2661 Truth Table D0 D1 L ... D15 D16 - - H - - D23 LE CLR SW0 SW1 SW15 SW16 - - L L OFF - - - - - - - L L ON - - - - L - - - L L - OFF - - - - H - - - L L - ON - - - - - - - - L L - - - - - - - - - - L - - L L - - - - - - - L L - - OFF - - - - H - - L L - - ON - - - - L - L L - - - OFF - - - H - L L - - - ON - - - - - - - - L L - - - - - - - - L L - - - - - - - - - - L L - - - - - - - - - - L L - - - - - - - - - L L L - - - - OFF - - - - H L L - - - - ON ... ... ... ... ... X X X X X X X H L HOLD PREVIOUS STATE X X X X X X X X H ALL SWITCHES OFF ... ... SW23 - Notes: 1. The 24 switches operate independently. 2. Serial data is clocked in on the L to H transition of the CLK. 3. All 24 switches go to a state retaining their latched condition at the rising edge of LE. When LE is low the shift registers data flow through the latch. 4. DOUT is high when data in the register 23 is high. 5. Shift register clocking has no effect on the switch states if LE is high. 6. The CLR clear input overrides all other inputs. Logic Timing Waveforms DN + 1 DN DATA IN DIN 5 0% LE 50% DN - 1 50% 50% tWLE tSD 50% CLOCK tSU DATA OUT DOUT VOUT (typ) th tDO 50% tON tOFF OFF 90% 1 0% ON CLR Doc.# DSFP-HV2661 NR010913 50% 5 0% tWCL 5 0% 6 Supertex inc. www.supertex.com HV2661 Pin Function Pin Function Pin Function Pin Function Pin Function 1 VPP 13 SW0 25 VPP 37 SW15 2 NC 14 Y0 26 NC 38 SW16 3 GND 15 SW1 27 SW9 39 Y5 4 CLR 16 SW2 28 Y3 40 SW17 5 LE 17 SW3 29 SW10 41 SW18 6 CLK 18 Y1 30 SW11 42 SW19 7 VDD 19 SW4 31 SW12 43 Y6 8 GND 20 SW5 32 SW13 44 SW20 9 DIN 21 SW6 33 Y4 45 SW21 10 DOUT 22 Y2 34 SW14 46 SW22 11 NC 23 SW7 35 NC 47 Y7 12 VNN 24 SW8 36 VNN 48 SW23 Doc.# DSFP-HV2661 NR010913 7 Supertex inc. www.supertex.com HV2661 48-Lead LQFP Package Outline (FG) 7.00x7.00mm body, 1.60mm height (max), 0.50mm pitch D D1 E1 E Note 1 (Index Area D1/4 x E1/4) 48 1 e b Top View View B A A2 L2 Seating Plane L L1 A1 θ Gauge Plane Seating Plane View B Side View Note: 1. A Pin 1 identifier must be located in the index area indicated. The Pin 1 identifier can be: a molded mark/identifier; an embedded metal marker; or a printed indicator. Symbol A A1 A2 b D D1 E E1 MIN Dimension NOM (mm) MAX 1.40* 0.05 1.35 0.17 8.80* 6.80* 8.80* 6.80* - - 1.40 0.22 9.00 7.00 9.00 7.00 1.60 0.15 1.45 0.27 9.20* 7.20* 9.20* 7.20* e L 0.50 BSC 0.45 0.60 0.75 L1 L2 1.00 REF 0.25 BSC θ 0O 3.5O 7O JEDEC Registration MS-026, Variation BBC, Issue D, Jan. 2001. * This dimension is not specified in the JEDEC drawing. Drawings are not to scale. Supertex Doc. #: DSPD-48LQFPFG Version, D041309. (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to http://www.supertex.com/packaging.html.) Supertex inc. does not recommend the use of its products in life support applications, and will not knowingly sell them for use in such applications unless it receives an adequate “product liability indemnification insurance agreement.” Supertex inc. does not assume responsibility for use of devices described, and limits its liability to the replacement of the devices determined defective due to workmanship. No responsibility is assumed for possible omissions and inaccuracies. Circuitry and specifications are subject to change without notice. For the latest product specifications refer to the Supertex inc. (website: http//www.supertex.com) Supertex inc. ©2013 Supertex inc. All rights reserved. Unauthorized use or reproduction is prohibited. Doc.# DSFP-HV2661 NR010913 8 1235 Bordeaux Drive, Sunnyvale, CA 94089 Tel: 408-222-8888 www.supertex.com