INFINEON BTS723GW

Datasheet PROFET BTS 723 GW
Smart High-Side Power Switch
Two Channels: 2 x 100mΩ
Status Feedback
Suitable for 42V
Product Summary
Operating Voltage
Vbb(on)
Active channels
On-state Resistance
RON
Nominal load current
IL(NOM)
Current limitation
IL(SCr)
Package
7.0 ... 58V
One
two parallel
105mΩ
53mΩ
2.9A
4.2A
8A
8A
P-DSO-14
General Description
•
•
•
N channel vertical power MOSFET with charge pump, ground referenced CMOS compatible input and

diagnostic feedback, monolithically integrated in Smart SIPMOS 80V technology.
Providing embedded protective functions
An array of resistors is integrated in order to reduce the external components
Applications
•
•
•
•
µC compatible high-side power switch with diagnostic feedback for 12V and 24V and 42V grounded loads
All types of resistive, inductive and capacitive loads
Most suitable for inductive loads
Replaces electromechanical relays, fuses and discrete circuits
Basic Functions
•
•
•
•
•
•
•
CMOS compatible input
Improved electromagnetic compatibility (EMC)
Fast demagnetization of inductive loads
Stable behaviour at undervoltage
Wide operating voltage range
Logic ground independent from load ground
Optimized inverscurrent capability
Block Diagram
Protection Functions
•
•
•
•
•
•
•
•
Short circuit protection
Overload protection
Current limitation
Thermal shutdown
Overvoltage protection (including load dump) with external
resistor
Reverse battery protection with external resistor
Loss of ground and loss of Vbb protection
Electrostatic discharge protection (ESD)
•
•
•
IN1
ST1
IN2
ST2
Diagnostic Function
•
Status pull
up voltage
Logic
Channel
1
Logic
Channel
2
PROFET
Diagnostic feedback with open drain output and integrated
GND
pull up resistors
Open load detection in OFF-state
Feedback of thermal shutdown in ON-state
Diagnostic feedback of both channels works properly in case of inverse current
Infineon Technologies AG
1 of 15
Vbb
OUT 1
Load 1
OUT 2
Load 2
2003-Oct-01
BTS 723 GW
Functional diagram
11
SPU: Pin for external Pull Up Voltage
Leadframe: Vbb
1, 7,
8, 14
2 IN1
R = 20kΩ
R = 12kΩ
Functions and Components of
inputlogic and gate-control:
ESD-protection
Charge pump, level shifter,
rectifier
Gate protection
Current limit
Limit for unclamped
inductive loads
OUT1
12, 13
Load 1
Function and components of
outputlogic
Open load detection
Short circuit detection
Temperature sensor
Load GND
Vbb
3 ST1
R = 850Ω
6 IN2
R = 20kΩ
5 ST2
R = 850Ω
Status 1
Function see truthtable
Logic channel one
Logic channel two
Function and components of
inputlogic and gate-control
equivalent to channel one
OUT2
9, 10
Function and components of
outputlogic equivalent to
channel one
Status 2
Function see truthtable
Load 2
Logic GND

PROFET
Load GND
4
Infineon Technologies AG
2
2003-Oct-01
BTS 723 GW
Pin configuration
Pin Definitions and Functions
Pin
1,7,
8,14,
2
6
12,13
9,10
3
5
4
11
Symbol Function
Positive power supply voltage. Design the
wiring for the simultaneous max. short circuit
Vbb
currents from channel 1 to 2 and also for low
thermal resistance
IN1
Input 1,2 activates channel 1,2 in case
of logic high signal
IN2
Output 1,2 protected high-side power output
OUT1
of channel 1,2. Design the wiring for the max.
short circuit current; both outputpins have to be
OUT2
connected in parallel for operation according
this spec.
ST1
Diagnostic feedback 1,2 of channel 1,2
open drain
ST2
GND
Logic Ground
Connection for external pull up voltage source
SPU
for the open drain status output.
Pull up resistors are integrated.
Infineon Technologies AG
3
(top view)
Vbb
IN1
ST1
GND
ST2
IN2
Vbb
1
2
3
4
5
6
7
•
14
13
12
11
10
9
8
Vbb
OUT1
OUT1
SPU
OUT2
OUT2
Vbb
2003-Oct-01
BTS 723 GW
Maximum Ratings at Tj = 25°C unless otherwise specified
Parameter
Symbol
Supply voltage (overvoltage protection see page 6)
Supply voltage for full short circuit protection
Tj,start = -40 ...+150°C
Output Voltage to Vbb
Negative voltage slope at output
Load current (Short-circuit current, see page 7)
Load dump protection2) VLoadDump = VA + Vs, VA = 27 V
RI3) = 8 Ω, td = 200 ms; IN = low or high,
each channel loaded with RL = 20 Ω,
Operating temperature range
Storage temperature range
Power dissipation (DC)5)
Ta = 25°C:
(all channels active)
Ta = 85°C:
Maximal switchable inductance, single pulse
Vbb = 12V, Tj,start = 150°C5),
IL = 2.5 A, EAS = 110 mJ, 0 Ω
one channel:
IL = 3.5 A, EAS = 278 mJ, 0 Ω
two parallel channels:
Vbb
Vbb
58
50
V
V
VON
-dVOUT/dt
IL
VLoad dump4)
70
20
V
V/µs
A
V
Tj
Tstg
Ptot
Values
Unit
IL(LIM)1)
70
-40 ...+150
-55 ...+150
3.0
1.6
°C
23.0
30.0
mH
VESD
1.0
kV
VIN
IIN
IST
VSPU
±42
±2.0
±2.0
±42
V
mA
ZL
W
see diagrams on page 12
Electrostatic discharge capability (ESD):
(Human Body Model) acc. MIL-STD883D, method 3015.7 and ESD
assn. std. S5.1-1993 R=1.5kΩ; C=100pF
Input voltage (DC)
Current through input pin (DC)
Current through status pin (DC)
Status pull up voltage
1)
2)
3)
4)
5)
V
Current limit is a protection function. Operation in current limitation is considered as "outside" normal
operating range. Protection functions are not designed for continuous repetitive operation.
Supply voltages higher than Vbb(AZ) require an external current limit for the GND and status pins (a 150Ω
resistor for the GND connection is recommended.
RI = internal resistance of the load dump test pulse generator
VLoad dump is setup without the DUT connected to the generator per ISO 7637-1 and DIN 40839
Device on 50mm*50mm*1.5mm epoxy PCB FR4 with 6cm2 (one layer, 70µm thick) copper area for Vbb
connection. PCB is vertical without blown air. See page 15
Infineon Technologies AG
4
2003-Oct-01
BTS 723 GW
Thermal Characteristics
Parameter and Conditions
Symbol
min
Thermal resistance
junction - soldering point5),6)
each channel: Rthjs
junction - ambient5)
one channel active: Rthja
all channels active:
Values
typ
Max
Unit
25
---
K/W
Values
min
typ
Max
Unit
----
-45
41
Electrical Characteristics
Parameter and Conditions, each of the two channels
Symbol
at Tj = -40...+150°C, Vbb = 24 V unless otherwise specified
Load Switching Capabilities and Characteristics
On-state resistance (Vbb to OUT); IL = 2 A, Vbb ≥ 7V
each channel,
Tj = 25°C: RON
Tj = 150°C:
two parallel channels, Tj = 25°C:
----
90
170
45
105
210
53
mΩ
see diagram, page 12
6)
Soldering point: Upper side of solder edge of device pin 15. See page 15
Infineon Technologies AG
5
2003-Oct-01
BTS 723 GW
Parameter and Conditions, each of the two channels
Symbol
at Tj = -40...+150°C, Vbb = 24 V unless otherwise specified
Nominal load current
one channel active: IL(NOM)
two parallel channels active:
2.9
4.2
---
A
--
--
1.0
mA
---
---
55
95
µs
dV/dton
1.0
--
5
V/µs
-dV/dtoff
1.0
--
5
V/µs
Vbb(on)
7.0
--
58
V
Vbb(ucp)
--58.5
4
-63
5.5
7.0
69
V
-----
13
µA
25
3
23
23
35
--
---
1.0
2.0
1.5
3.0
mA
Output current while GND disconnected or pulled up 8); IL(GNDhigh)
IN
Turn-off time
IN
RL = 12 Ω
Slew rate on 9)
10 to 30% VOUT, RL = 12 Ω:
Slew rate off 9)
70 to 40% VOUT, RL = 12 Ω:
to 90% VOUT: ton
to 10% VOUT: toff
Operating Parameters
Operating voltage
Undervoltage restart of charge pump
Tj =-40...+25°C:
Tj =+150°C:
Overvoltage protection10)
I bb = 40 mA
Standby current11)
Tj =-40°C...+25°C):
Tj =+125°C12 :
VIN = 0; see diagram page 10
Tj =+150°C:
Off-State output current (included in Ibb(off))
VIN = 0; each channel
Operating current 13), VIN = 5V,
one channel on:
all channels on:
Unit
2.5
4.0
Device on PCB7), Ta = 85°C, Tj ≤ 150°C
Vbb = 30 V, VIN = 0,
see diagram page 11
Turn-on time9)
Values
min
typ
Max
Vbb(AZ)
Ibb(off)
IL(off)
IGND
V
µA
7)
Device on 50mm*50mm*1.5mm epoxy PCB FR4 with 6cm2 (one layer, 70µm thick) copper area for Vbb
connection. PCB is vertical without blown air. See page 15
8) not subject to production test, specified by design
9) See timing diagram on page 13.
10) Supply voltages higher than V
bb(AZ) require an external current limit for the GND; a 150Ω resistor is
recommended. See also VON(CL) in table of protection functions and circuit diagram on page 10.
11) Measured with load; for the whole device; all channels off
12) not subject to production test, specified by design
13) Add I , if I
ST
ST > 0
Infineon Technologies AG
6
2003-Oct-01
BTS 723 GW
Parameter and Conditions, each of the two channels
Symbol
at Tj = -40...+150°C, Vbb = 24 V unless otherwise specified
Values
min
typ
Max
Unit
Protection Functions14)
Current limit, (see timing diagrams, page 13)
Tj =-40°C: IL(lim)
Tj =25°C:
Tj =+150°C:
--5
10
9
8
12
---
A
---
8
8
---
A
--
2
--
ms
59
150
--
64
-10
70
---
V
°C
K
-Vbb
-VON
---
-650
24
--
V
mV
IGND(inv cur)
--
--
15
mA
Repetitive short circuit current limit 15),
Tj = Tjt
each channel IL(SCr)
two parallel channels
(see timing diagrams, page 13)
Initial short circuit shutdown time
Tj,start =25°C: toff(SC)
(see timing diagrams on page 13)
Output clamp (inductive load switch off)16)
VON(CL)
Tjt
∆Tjt
at VON(CL) = Vbb - VOUT, IL = 1 A
Thermal overload trip temperature
Thermal hysteresis
Reverse Battery
Reverse battery voltage 17)
Drain-source diode voltage (Vout > Vbb) 18)
IL = - 3.0 A, Tj = +150°C
Inverse current 19)
GND current in case of 3A inverse current 20)
14)
Integrated protection functions are designed to prevent IC destruction under fault conditions described in the
data sheet. Fault conditions are considered as "outside" normal operating range. Protection functions are not
designed for continuous repetitive operation.
15) not subject to production test, specified by design
16) If channels are connected in parallel, output clamp is usually accomplished by the channel with the lowest
VON(CL)
17) Requires a 150 Ω resistor in GND connection. The reverse load current through the intrinsic drain-source
diode has to be limited by the connected load. Power dissipation is higher compared to normal operating
conditions due to the voltage drop across the drain-source diode. The temperature protection is not active
during reverse current operation! Input and Status currents have to be limited (see max. ratings page 4 and
circuit page 10).
18) not subject to production test, specified by design
19) not subject to production test, specified by design
20) In case of an inverse current of 3A the both status outputs must not be disturbed.
The neighbour channel can be switched normally; not all paramters lay within the range of the spec
Please note, that in case of an inverse current no protection function is active. The power dissipation is
higher compared to normal operation in forward mode due to the voltage drop across the drain-source diode
(as it is with reverse polaritiy). If this mode lasts for a too long time the device can be destroyed.
Infineon Technologies AG
7
2003-Oct-01
BTS 723 GW
Parameter and Conditions, each of the two channels
Symbol
Values
min
typ
Max
IL(off)
VOUT(OL)
-2.0
3
2.85
-3.7
µA
V
VON(SC)
--
4.0
--
V
Input RI
Status RST
Status pull up Rpull up
VIN(T+)
VIN(T-)
∆ VIN(T)
VIN = 0.4 V: IIN(off)
VIN = 5 V: IIN(on)
-0.53
-1.2
1.0
-1
10
20
0.85
12
--0.25
-25
-1.2
-2.2
--15
50
kΩ
kΩ
kΩ
V
V
V
µA
µA
VST(high)
VSPU = 5V: VST(low)
5.4
--
6.1
--
-0.4
V
at Tj = -40...+150°C, Vbb = 24 V unless otherwise specified
Diagnostic Characteristics
Open load detection current 21)
Open load detection voltage
Short circuit detection voltage 22)
Vbb(pin 1,7,8,14) to OUT1 (pin 12,13) resp.
Vbb(pin 1,7,8,14) to OUT2 ( pin 9,10)
Input and Status Feedback 23)
Integrated resistors; Tj =25°C:
(see circuit page 2)
Input turn-on threshold voltage
Input turn-off threshold voltage
Input threshold hysteresis
Off state input current
On state input current
Status output (open drain)
Zener limit voltage
Status low voltage
Unit
21)
not subject to production test, specified by design
not subject to production test, specified by design
23) If a ground resistor R
GND is used, add the voltage drop across these resistors.
22)
Infineon Technologies AG
8
2003-Oct-01
BTS 723 GW
Truth Table
Channel 1
Channel 2
Normal
operation
Open load
Short circuit
to GND
Short circuit
to Vbb
Overtemperature
Input 1
Input 2
level
L
H
L
H
L
H
L
H
L
H
Output 1
Output 2
level
L
H
VOUT > 2.7V
H
L
L
H
H
L
L
Status 1
Status 2
BTS 723
L
H
H
H
L
L
H
H
L
L
Parallel switching of channel 1 and 2 is easily possible by connecting the inputs and outputs in parallel. In this
mode it is recommended to use only one status.
Terms
V
bb
Ibb
Leadframe
I IN1
2
IN1
I ST1
V
IN1 VST1
3
ST1
I L1
PROFET OUT1
Channel 1
GND
Leadframe
I IN2
Vbb
6
VON1
IN2
I ST2
12,13
VOUT1
V
IN2
VST2
5
ST2
Vbb
I L2
PROFET OUT2
Channel 2
VON2
9,10
GND
VOUT2
4
I GND
R
GND
Leadframe (Vbb) is connected to pin 1,7,8,14
External RGND optional; a single resistor RGND = 150Ω for reverse battery protection up to the max.
operating voltage.
Infineon Technologies AG
9
2003-Oct-01
BTS 723 GW
Inductive and overvoltage output clamp,
Input circuit (ESD protection), IN1 or IN2
OUT1 or OUT2
R
IN
I
+Vbb
VZ
ESD-ZD I
I
I
V
GND
ON
OUT
The use of ESD zener diodes as voltage clamp at DC
conditions is not recommended.
Power GND
Status output, ST1 or ST2
VON clamped to VON(CL) = 64 V typ.
Status Pull Up Voltage
Overvolt. and reverse batt. protection
RPull up
R ST(ON)
Status pull up voltage
ST
RST
GND
R Status puul up
ESDZD
IN
+ Vbb
V
RI
Z2
Logic
ST
OUT
R ST
ESD-Zener diode: 6.1 V typ., RST(ON) < 250 Ω,
RST = 850 Ω typ., Rpull up = 12 kΩ typ.
The use of ESD zener diodes as voltage clamp at DC
conditions is not recommended
V
PROFET
Z1
GND
R GND
Signal GND
Short Circuit detection
Fault Signal at ST-Pin: VON > 4.0 V typ, no switch off by
the PROFET itself, external switch off recommended!
R Load
Load GND
VZ1 = 6.1 V typ., VZ2 = 63 V typ., RGND = 150 Ω,
RI = 850 Ω typ., RST = 20 kΩ typ., Rpull up = 12 kΩ typ
In case of reverse battery the load current has to be
limited by the load. Temperature protection is not
active
+ V bb
V
ON
OUT
Logic
unit
Short circuit
detection
Infineon Technologies AG
10
2003-Oct-01
BTS 723 GW
Vbb disconnect with energized inductive
load
Open-load detection, OUT1 or OUT2
OFF-state diagnostic condition:
Open load, if VOUT > 2.7 V typ. (IN low)
IL(OL) typ. 2µA
An external resitor can be used to increase the open
load detection current
V
high
IN
Vbb
PROFET
OUT
ST
bb
GND
V
ON
V
OFF
OUT
I
Open load
detection
Logic
unit
bb
For inductive load currents up to the limits defined by ZL
(max. ratings and diagram on page 12) each switch is
protected against loss of Vbb.
L(OL)
Consider at your PCB layout that in the case of Vbb disconnection with energized inductive load all the load current
flows through the GND connection.
Signal GND
GND disconnect
IN
Vbb
OUT
PROFET
ST
GND
V
bb
V
IN
V
V
GND
ST
Any kind of load.
Due to VGND > 0, no VST = low signal available.
GND disconnect with GND pull up
IN
Vbb
PROFET
OUT
ST
GND
V
V
bb
V
IN ST
V
GND
Any kind of load. If VGND > VIN - VIN(T+) device stays off
Due to VGND > 0, no VST = low signal available.
Infineon Technologies AG
11
2003-Oct-01
BTS 723 GW
Inductive load switch-off energy
dissipation
Typ. on-state resistance
RON = f (Vbb,Tj ); IL = 2 A, IN = high
E bb
RON [mOhm]
E AS
ELoad
Vbb
IN
Tj = 150°C
180
PROFET
=
OUT
L
ST
GND
ZL
{
R
EL
160
ER
120
L
25°C
Energy stored in load inductance:
2
80
EL = 1/2·L·I L
While demagnetizing load inductance, the energy
dissipated in PROFET is
-40°C
40
EAS= Ebb + EL - ER= VON(CL)·iL(t) dt,
with an approximate solution for RL > 0 Ω:
IL· L
EAS=
(V + |VOUT(CL)|)
2·RL bb
ln (1+ |V
0
IL·RL
OUT(CL)|
3
)
5
7
9
30
40
Vbb [V]
Typ. standby current
Maximum allowable load inductance for
a single switch off (one channel)5)
Ibb(off) = f (Tj ); Vbb = 9...34 V, IN1,2,3,4 = low
L = f (IL ); Tj,start = 150°C, Vbb = 12 V, RL = 0 Ω
Ibb(off) [µA]
45
ZL [mH]
1000
40
35
30
100
25
20
15
10
10
5
0
-50
1
1
2
3
4
5
6
7
0
50
100
150
200
Tj [°C]
IL [A]
Infineon Technologies AG
12
2003-Oct-01
BTS 723 GW
Timing diagrams
All channels are symmetric and consequently the diagrams are valid for channel 1 and
channel 2
Figure 1a: Vbb turn on, :
Figure 2b: Switching an inductive load
IN
IN
t d(bb IN)
V
bb
ST
V
V
OUT
OUT
A
I
ST open drain
L
t
t
A
in case of too early VIN=high the device may not turn on (curve A)
td(bb IN) approx. 150 µs
Figure 2a: Switching a resistive load,
turn-on/off time and slew rate definition:
Figure 3a: Short circuit:
shut down by overtempertature, reset by cooling
IN
IN
V OUT
VOUT
normal
operation
90%
t on
dV/dton
10%
dV/dtoff
t
I
off
Output short to GND
I
L
L(lim)
I
L(SCr)
IL
ST
t
t
off(SC)
t
Heating up requires several milliseconds, depending on external
conditions. External shutdown in response to status fault signal
recommended.
Infineon Technologies AG
13
2003-Oct-01
BTS 723 GW
Figure 6: Overvoltage, no shutdown:
Figure 4a: Overtemperature:
Reset if Tj <Tjt
IN
IN
Vbb
VON(CL)
ST
V
V
OUT
OUT
VOUT(OL)
ST
T
J
t
t
Figure 5a: Open load, : detection in OFF-state, open
load occurs in off-state
IN
ST
V
OUT
VOUT(OL)
I
L
normal
open
*)
normal
*)
t
*) IL = 2 µA typ. VOUT > 2.7V
Infineon Technologies AG
14
2003-Oct-01
BTS 723 GW
Package and Ordering Code
Published by
Infineon Technologies AG,
St.-Martin-Strasse 53,
D-81669 München
© Infineon Technologies AG 2001
All Rights Reserved.
Standard: P-DSO-14-9
Sales Code
BTS 723 GW
Ordering Code
Q67060-S7501
Attention please!
The information herein is given to describe certain
components and shall not be considered as a guarantee of
characteristics.
Terms of delivery and rights to technical change reserved.
We hereby disclaim any and all warranties, including but not
limited to warranties of non-infringement, regarding circuits,
descriptions and charts stated herein.
Infineon Technologies is an approved CECC manufacturer.
Information
For further information on technology, delivery terms and
conditions and prices please contact your nearest Infineon
Technologies Office in Germany or our Infineon
Technologies Representatives worldwide (see address list).
All dimensions in millimetres
Definition of soldering point with temperature Ts:
upper side of solder edge of device pin 1.
Warnings
Due to technical requirements components may contain
dangerous substances. For information on the types in
question please contact your nearest Infineon Technologies
Office.
Pin 1
Infineon Technologies Components may only be used in lifesupport devices or systems with the express written approval
of Infineon Technologies, if a failure of such components can
reasonably be expected to cause the failure of that lifesupport device or system, or to affect the safety or
effectiveness of that device or system. Life support devices
or systems are intended to be implanted in the human body,
or to support and/or maintain and sustain and/or protect
human life. If they fail, it is reasonable to assume that the
health of the user or other persons may be endangered.
Printed circuit board (FR4, 1.5mm thick, one layer
70µm, 6cm2 active heatsink area) as a reference for
max. power dissipation Ptot, nominal load current
IL(NOM) and thermal resistance Rthja
25mm
12mm
Infineon Technologies AG
12mm
15
2003-Oct-01