Freescale Semiconductor, Inc. User’s Guide Document Number: KT50XS4200UG Rev. 1.0, 9/2014 KIT50XS4200EKEVB Evaluation Board Figure 1. KIT50XS4200EKEVB © Freescale Semiconductor, Inc., 2014. All rights reserved. Contents 1 Important Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Getting to Know the Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 Accessory Interface Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 5 Installing the Software and Setting up the Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 6 Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 7 Board Layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 8 Board Bill of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 9 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 10 Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 KT50XS4200UG Rev. 1.0 2 Freescale Semiconductor, Inc. Important Notice 1 Important Notice Freescale provides the enclosed product(s) under the following conditions: This evaluation kit is intended for use of ENGINEERING DEVELOPMENT OR EVALUATION PURPOSES ONLY. It is provided as a sample IC pre-soldered to a printed circuit board to make it easier to access inputs, outputs, and supply terminals. This evaluation board may be used with any development system or other source of I/O signals by simply connecting it to the host MCU or computer board via off-the-shelf cables. This evaluation board is not a Reference Design and is not intended to represent a final design recommendation for any particular application. Final device in an application will be heavily dependent on proper printed circuit board layout and heat sinking design as well as attention to supply filtering, transient suppression, and I/O signal quality. The goods provided may not be complete in terms of required design, marketing, and or manufacturing related protective considerations, including product safety measures typically found in the end product incorporating the goods. Due to the open construction of the product, it is the user's responsibility to take any and all appropriate precautions with regard to electrostatic discharge. In order to minimize risks associated with the customers applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. For any safety concerns, contact Freescale sales and technical support services. Should this evaluation kit not meet the specifications indicated in the kit, it may be returned within 30 days from the date of delivery and will be replaced by a new kit. Freescale reserves the right to make changes without further notice to any products herein. Freescale makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typical”, must be validated for each customer application by customer’s technical experts. Freescale does not convey any license under its patent rights nor the rights of others. Freescale products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale product could create a situation where personal injury or death may occur. Should the Buyer purchase or use Freescale products for any such unintended or unauthorized application, the Buyer shall indemnify and hold Freescale and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges Freescale was negligent regarding the design or manufacture of the part.Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. © Freescale Semiconductor, Inc. 2014 KT50XS4200UG Rev. 1.0 Freescale Semiconductor, Inc. 3 Getting Started 2 Getting Started 2.1 Kit Contents/Packing List The KIT50XS4200EKEVB contents include: • Assembled and tested evaluation board/module in anti-static bag. • Quick Start Guide, Analog Tools • Warranty card 2.2 Jump Start Freescale’s analog product development boards help to easily evaluate Freescale products. These tools support analog mixed signal and power solutions including monolithic ICs using proven high-volume SMARTMOS mixed signal technology, and system-in-package devices utilizing power, SMARTMOS and MCU dies. Freescale products enable longer battery life, smaller form factor, component count reduction, ease of design, lower system cost and improved performance in powering state of the art systems. • Go to www.freescale.com/analogtools • Locate your kit • Review your Tool Summary Page • Look for Jump Start Your Design • Download documents, software and other information Once the files are downloaded, review the user guide in the bundle. The user guide includes setup instructions, BOM and schematics. Jump start bundles are available on each tool summary page with the most relevant and current information. The information includes everything needed for design. 2.3 Required Equipment and Software To use this kit, you need: • DC power supply capable of supplying up to 40 A at 6.0 to 58 V • Electronic/resistive loads to load the various power channels • 5.0 V Power supply, 1.0 A current capability • KITUSBSPIEVME Interface Dongle • USB cable with termination Type A and Type B • DB25 cable (optional) 2.4 System Requirements The kit requires the following to function properly with the software: • USB enabled computer with Windows Vista, Windows 7 • CD Reader KT50XS4200UG Rev. 1.0 4 Freescale Semiconductor, Inc. Getting to Know the Hardware 3 Getting to Know the Hardware 3.1 Board Overview The KIT50XS4200EKEVB demonstrates the capability of the MC50XS4200 as a 24 V dual high-side switch that provides integrated control with protective and diagnostic functions. This product has been designed for truck, bus, and industrial applications. The low RDS(on) channels (< 50 mΩ) control different load types; bulb lamps, solenoids, or DC motors. Control, device configuration, and diagnostics are performed through a 16-bit SPI interface, allowing easy integration into existing applications. Both channels can be controlled individually by external/internal clock signals or by direct inputs. Using the internal clock allows fully autonomous device operation. Programmable output voltage slew rates (individually programmable) helps improve EMC performance. To avoid shutting off the device upon inrush current, while still being able to closely track the load current, a dynamic overcurrent threshold profile is featured. Switching current of each channel can be sensed via a programmable sensing ratio. Whenever communication with the external microcontroller is lost, the device enters a fail-safe operation mode, but remains operational, controllable, and protected. 3.2 Board Features The board features are as follows: • Input voltage operation range from 6.0 to 58 V • Dual high-side switch • Programming, control, and diagnostics accomplished via the use of a 16-bit SPI interface • Output with selectable slew-rate satisfy electromagnetic compatibility (EMC) requirements • Each output can be controlled with direct inputs or internal PWM modulated clock signal 3.3 Device Features This evaluation board features the following Freescale product: Table 1. Device Features Device Description Features • Two fully-protected 50 mΩ (at 25 °C) high-side switches MC50XS4200 The 50XS4200 device is part of a 24 V dual high-side switch product family with integrated control, and a high number of protective and diagnostic functions. • Up to 3.0 A steady-state current per channel • Separate bulb and DC motor latched overcurrent handling • Individually programmable internal/external PWM clock signals • Overcurrent, short-circuit, and overtemperature protection with programmable autoretry functions • Accurate temperature and current sensing KT50XS4200UG Rev. 1.0 Freescale Semiconductor, Inc. 5 Getting to Know the Hardware 3.4 Board Description Figure 2 describes the main blocks of the KIT50XS4200EKEVB. Ext. VDD CLK 5V input Over FSB, FOSB, current RSTB LEDs profile Direct inputs Sync output Optic fiber interface (not mounted) MC50XS4200 Power supply inputs SPI connector Sense Free wiring area Optic fiber interface (not mounted) Freewheeling diodes Outputs HS0 & HS1 Figure 2. Board Description KT50XS4200UG Rev. 1.0 6 Freescale Semiconductor, Inc. Getting to Know the Hardware Table 2. Board Description Name Description VDD 5.0 V Input connector for VDD supply 5.0 V External Clock Input Clock input connector for external PWM clock signal FSB, FSOB, RSTB LEDs LEDs for FSB, FSOB, RSTB states, LEDs are ON when three signals are active, (Example: when a fault is detected, FSB open drain is ON, LED will be ON). The LED feature is de-selectable Over current profile Jumpers to select either bulb or DC motor overcurrent handling Direct Inputs IN0 and IN1 direct inputs to control the outputs Sync Output Sync signal output to synchronize the ECU with sense current measurement Power Supply Inputs Connectors for VPWR from 6.0 V up to 58 V Sense CSNS output for current and temperature sensing Free wiring area Area for free wiring by user Outputs HS0 & HS1 Outputs of the high-side switch Optic Fibre Interface Option to use fiber optic for SPI interface (not mounted) SPI Interface 25 pin connector for SPI communication MC50XS4200 Device high-side switch 50 mΩ output 3.5 LED Display The following LEDs are provided as visual output devices for the KIT50XS4200EKEVB evaluation board: D5, D6 & D7 D2 D8 & D9 D10 & D11 D1 Figure 3. LED Display KT50XS4200UG Rev. 1.0 Freescale Semiconductor, Inc. 7 Getting to Know the Hardware Table 3. LED Display LED ID Description Requires D5 ON when FSB active i.e Fault detected (As FSB is open drain pin, FSB is close to GND when activated) JMP2 connected D6 ON when FS0B active i.e Fault detected on VDD or SPI (As FSOB is open drain pin, FS0B is close to GND when activated) JMP2 connected D7 ON when RSTB is low JMP2 connected D8 Reflects CONF0 state for channel 0 ON when CONF0 = 5.0 V ON when CONF0 = DC motor JMP4 connected between position 1 & 2 D9 Reflects CONF1 state for channel 1 ON when CONF0 = 5.0 V ON when CONF0 = DC motor JMP5 connected between position 1 & 2 D10 ON when IN0 = High JMP8 connected D11 ON when IN1 = High JMP9 connected D1 ON when HS0= High JMP6 connected D2 ON when HS1= High JMP7 connected KT50XS4200UG Rev. 1.0 8 Freescale Semiconductor, Inc. Getting to Know the Hardware 3.6 Connectors Connectors are intended to connect all external control signals and to connect outputs to loads. The GND reference for HS0 and HS1 is GND. IN1 IN0 VDD CLK SYNC GND SPI interface & controls VPWR HS1 HS0 Figure 4. Connectors Table 4. Connectors Connector ID CN1 Description Output high-side switch channel 0 CN2 Output high-side switch channel 1 CN3 VPWR, 6.0 to 58 V CN4 GND, ground reference J5 Direct input for channel 0 J6 Direct input for channel 1 KT50XS4200UG Rev. 1.0 Freescale Semiconductor, Inc. 9 Getting to Know the Hardware Table 4. Connectors (continued) Connector ID J7 Description SYNC Output for current sense synchronization SPI interface connector and controls Note: Control signal and fault signal from DB25 connector can be set through the USB to SPI interface 1. RSTB 2. CSB 3. MOSI 4. SCLK 5. IN0 6. IN1 7. SYNC 8. CONF0 9. CONF1 10. NC 11. NC JP1 12. MISO 13. NC 14. NC 15. NC 16. FSOB 17. FSB 18. NC 19. NC 20. GND 21. NC 22. NC 23. NC 24. NC 25. NC KT50XS4200UG Rev. 1.0 10 Freescale Semiconductor, Inc. Getting to Know the Hardware 3.7 Test Point Definitions The following test-point jumpers provide access to signals on the MC50XS4200 IC: IN1 IN0 VDD CLK TP6 SYNC TP7 TP9 GND TP8 TP10 TP13 TP11 TP12 TP5 TP2 TP3 VPWR TP1 TP4 Figure 5. Test Point Definitions Table 5. Test Point Definitions Test Point Name Description TP1 SV VPWR Power supply sense TP2 VP VPWR Power supply TP3 SHS1 High-side channel1 sense TP4 SHS0 High-side channel0 sense TP5 SYNC Current sense synchronization TP6 FSB Fault status TP7 FSOB Fail-safe output TP8 CSNS Output current sense monitoring TP9 CLK PWM clock TP10 SCLK SPI serial clock TP11 MISO Serial Output (SO) TP12 CSB Chip select TP13 MOSI Serial Input (SI) KT50XS4200UG Rev. 1.0 Freescale Semiconductor, Inc. 11 Getting to Know the Hardware 3.8 USB/SPI Dongle Connector USB/SPI dongle connector mates with the 16 conductor flat cable connecting to the USB/SPI Dongle (KITUSBSPIDGLEVME).This is a 16 pin, 0.1” center, dual-row connector designed to interface directly to the USB/SPI Dongle unit. The USB/SPI dongle connector consists of the following 16 pins. Table 6. USB/SPI Dongle Connector Description Pin Number 3.9 Name Description 1 CSB SPI signal, Chip Select Bar 2 CNTL2 CNTL2 connected to MTX 3 SO 4 CNTL1 5 SI 6 CNTL0 SPI signal, Serial Out CNTL1 connected to RIN1 SPI signal, Serial In CNTL0 connected to RIN2 7 SCLK 8 DATA4 DATA4 connected to O2HIN SPI signal, Serial Clock 9 CNTL3 CNTL3 connected to RESETB 10 DATA3 NC 11 VDD 12 DATA2 +5.0 Volt VDD from USB DATA2 connected to IGNIN1 13 +3.3 V +3.3 V from USB (Not Used) 14 DATA1 NC 15 GND 16 DATA0 Signal Ground DATA0 connected to INJIN1 Jumper Definitions The following table defines the evaluation board jumper positions and explains their functions. Table 7. Jumper Definitions Jumper Description Setting Connection Diode not connected JMP1 A diode is connected between ground and high-side output channel 0 (HS0) Diode connected KT50XS4200UG Rev. 1.0 12 Freescale Semiconductor, Inc. Getting to Know the Hardware Table 7. Jumper Definitions (continued) Jumper Description Setting Connection Direct input IN0 is internally tied to ground by internal pull-down resistor Direct input IN0 is connected to banana plug J5 JP2 The direct input selection for channel 0 (IN0) Direct input IN0 is connected to the USB/SPI dongle JP1 Direct input IN0 is tied to VDD i.e HS0 is fully ON JP3 The direct input selection for channel 1 (IN1) Same description as for JP2 D5, D6, D7 are not supplied therefore state of FSB, FSOB, and RSTB is not reflected on LEDs JMP2 The supply of MC74HC4049 (U7) is connected or disconnected to reduce consumption of D5, D6 & D7 on board D5, D6, D7 are supplied therefore state of FSB, FSOB, and RSTB is reflected on LEDs SYNC signal is open drain, without any jumper the SYNC signal is only available on the test point TP5. In that configuration, an external pull-up resistor is required outside the EVB. JMP3 SYNC Signal SYNC signal is open drain, SYNC is connected to on-board pull-up resistor to VDD Note: Recommended position for regular use of SYNC signal SYNC is directly connected to the 1 mm banana plug, the SYNC signal is not connected to pull-up resistor. In that configuration, an external pull-up resistor is required outside the EVB. KT50XS4200UG Rev. 1.0 Freescale Semiconductor, Inc. 13 Getting to Know the Hardware Table 7. Jumper Definitions (continued) Jumper Description Setting Connection CONF0 input pin is internally connected to a voltage regulator (3.3 V) CONF0 = 1, DC motor overcurrent protection profile selected JMP4 CONF0 configuration pin for channel 0 CONF0 input pin is connected to VDD (5.0 V) CONF0 = 1, DC motor overcurrent protection profile selected This position enables LED emitting CONF0 input pin is connected to GND CONF0 = 0, bulb overcurrent protection profile selected JMP5 CONF1 configuration pin for channel Same description as for JMP4 LED on HS0 is disconnected JMP6 LED on HS0 LED on HS0 is connected JMP7 LED on HS1 Same description as for JMP6 LED on IN0 is disconnected JMP8 LED on IN0 LED on IN0 is connected JMP9 LED on IN1 Same description as for JMP8 JMP10 A diode is connected between ground and high-side output channel 1 (HS1) Same description as for JMP1 Test point TP8 is not connected to CSNS JMP11 CSNS output CSNS is connected to TP8 The device ground is not connected Intent of that position is to simulate ground disconnection JMP12 Device GND Device connected to GND RSTB is internally tied to GND JMP13 RSTB state RSTB is connected to connector DB25 (JP1) RSTB is connected to VDD (5.0 V), device cannot be reseted KT50XS4200UG Rev. 1.0 14 Freescale Semiconductor, Inc. Accessory Interface Board 4 Accessory Interface Board The KIT50XS4200EKEVB kit may be used with the KITUSBSPIEVME interface dongle (shown below), which provides a USB-to-SPI interface. This small board makes use of the USB, SPI, and parallel ports built into Freescale’s MC68HC908JW32 microcontroller. The main function provided by this dongle is to allow Freescale evaluation kits having a parallel port to communicate via a USB port to a PC. Figure 6. KITUSBSPIEVME Interface Dongle 4.1 Connecting KITUSBSPIEVME to the Board with DB25 Cable The KITUSBSPIEVME is connected to a computer through USB cable and a DB25 parallel cable as shown in Figure 7. Figure 7. Connecting KITUSBSPIEVME to the Board with DB25 Cable KT50XS4200UG Rev. 1.0 Freescale Semiconductor, Inc. 15 Accessory Interface Board 4.2 Connecting KITUSBSPIEVME to the Board without DB25 Cable The KITUSBSPIEVME can be directly connected to the KIT50XS4200EKEVB as shown in Figure 8. Figure 8. Connecting KITUSBSPIEVME to the Board without DB25 Cable KT50XS4200UG Rev. 1.0 16 Freescale Semiconductor, Inc. Installing the Software and Setting up the Hardware 5 Installing the Software and Setting up the Hardware 5.1 Installing SPIGen Freeware on your Computer The latest version of SPIGen is designed to run on any Windows 8, Windows 7, Vista, or XP-based operating system. To install the software, go to www.freescale.com/analogtools and select your kit. Click on the link to open the corresponding Tool Summary Page. Look for “Jump Start Your Design”. Download to your computer desktop the SPIGen software as well as the associated configuration file. Run the install program from the desktop. The Installation Wizard guides you through the rest of the process. To use SPIGen, go to the Windows Start menu, then Programs, then SPIGen, and click on the SPIGen icon. The SPIGen Graphic User Interface (GUI) appears. Go to the file menu in the upper left hand corner of the GUI, and select “Open”. In the file selection window appearing, set the “Files of type:” drop-down menu to “SPIGen Files (*.spi)”. (As an exceptional case, the file name may have a .txt extension, in which case you should set the menu to “All Files (*.*)”.) Next, browse for the configuration file you saved on your desktop earlier and select it. Click “Open”, and SPIGen creates a specially configured SPI command generator for your evaluation board. The GUI is shown in Figure 9. The text at the top is the name of the configuration file loaded. The left side panel displays folders that group user interfaces. The process of loading the configuration file has assigned a list of “Extra Pins” as well as a list of “Quick Commands”, all of which are board-specific. Figure 9. SPIGen GUI KT50XS4200UG Rev. 1.0 Freescale Semiconductor, Inc. 17 Installing the Software and Setting up the Hardware 5.2 Configuring the Hardware The KIT50XS4200EKEVB operates with a single DC power supply from 6.0 to 58 V, and is fully controlled via the SPI with the help of an USB-SPI KITUSBSPIEVME EVB kit, requiring a 5.0 V DC power supply. Power supply 5V KITUSBSPIEVME KIT50XS4200EVBE Power supply 24V Parallel cable 25 pins USB cable Load 1 Load 2 Figure 10. KIT50XS4200EKEVB Board Setup KT50XS4200UG Rev. 1.0 18 Freescale Semiconductor, Inc. Installing the Software and Setting up the Hardware 5.2.1 Step-by-step Instructions for Setting up the Hardware using SPIGen To perform the demonstration examples, the following connections and setup must be performed: 1. Ready the computer and install the SPIGen. 2. To start working with KIT50XS4200EKEVB, provide 24 V input voltage between 6.0 to 58 V, by connecting the (+) probe to the VPWR pin, and the (-) probe to the GND pin, on the input power terminal block. 3. Apply a 5.0 V input voltage between VDD and the GND terminal. 4. Connect the load between the HS0 (or HS1) pin and the (-) terminal with the 24 V power supply. 5. Start SPIGen. Figure 11. SPIGen GUI KT50XS4200UG Rev. 1.0 Freescale Semiconductor, Inc. 19 Installing the Software and Setting up the Hardware 6. To configure SPD50, download the Config SPI file. Select File and open SPD50_config.file Figure 12. Loading Config File 7. To initialize SPD50, perform the following steps: • Set RSTB to level high by entering Extra Pins in the Session Log text box • Set Control0 = High • Set Bit 6 of SO to 1 • Click Send Once Figure 13. SPD50 Initialization KT50XS4200UG Rev. 1.0 20 Freescale Semiconductor, Inc. Installing the Software and Setting up the Hardware 8. For faster initialization, perform the following steps: • Click Send One Command at a Time • Select Init for the setup • Click Send Once • Session Log displays log of send and receive commands 1 3 4 2 Figure 14. Alternate Initialization Sequence with Batch Commands KT50XS4200UG Rev. 1.0 Freescale Semiconductor, Inc. 21 Installing the Software and Setting up the Hardware 9. After initialization, perform the following steps: • Click Send One Command at a Time • Select Out0 Fully On from the list • Click Send Once • Session Log displays log of send and receive commands Result : The bulb connected to HS0 is turned on. 3 1 4 2 Figure 15. Single Command Sequence KT50XS4200UG Rev. 1.0 22 Freescale Semiconductor, Inc. A B C TP4 MISO HS0 SHS1 HS1 SHS0 19 20 21 22 23 10 11 12 13 14 15 16 17 18 24 1 14 2 15 3 16 4 17 5 18 6 19 7 20 8 21 9 22 10 23 11 24 12 25 13 HS0 HS0 HS0 HS0 HS0 HS1 HS1 HS1 HS1 HS1 NC NC NC NC NC VPWR CONF1 CONF0 SYNC IN1J MOSI FS0B SCLK FSB IN0J CSB RSTB_ 1 GND 2 2PTS JMP12 CLOCK RSTB CSB SCLK SI VDD SO FSB SYNC CSNS IN0 IN1 FSOB CONF0 CONF1 DB25 GND TSTPTTSTPTTSTPTTSTPTTSTPTTSTPTTSTPT TP14 TP15 TP16 TP17 TP18 TP19 TP20 TSTPT JUMP3 1 2 3 JMP13 TSTPT GND TSTPT TSTPT TSTPT C6 TP2 SVPWR 100nF TSTPT GND TSTPT TSTPT TP3 TP1 VDD RSTB RSTB_ TP11 TP10 TP13 TP12 JP1 33 VPWR D GND 25 GND 8 2 1 2 1 2 3 4 5 6 7 9 26 27 28 29 30 31 32 10k R24 TP5 TSTPT 10k R18 C2 100nF GND CLOCK RSTB CSB SCLK MOSI VDD MISO FSB SYNC CSNS IN0 IN1 FS0B CONF0 CONF1 SYNC SOIC32 U6 MISO GND C1 1uF 2 1 R25 10k 8 RES1 R8 1 1 VDD 3 1 VDD VDD VDD 2.7R R4 2.7R R3 2.7R R2 GND GND EM_2MM_BLEU 1 J9 JUMP3 1 2 3 JMP3 EM_2MM_JAUNE J7 1 47R R5 EM_2MM_JAUNE J8 GND U1A SN75451 R1 2k7 C7 100nF GND 1 TP9 TSTPT 3 4 VDD 3 1 2 3 4 4 GND C5 100nF GND GND CSB C4 100nF GND GND SCLK 1 2 3 4 1 2 3 4 1 2 3 4 GND GND RSTB FS0B FSB 3 HFBR2528 VO GND VCC NC HFBR2528 U4 VO GND VCC NC HFBR2528 U3 VO GND VCC NC U2 HFBR1528 Anode Cathode GND GND U5 C3 100nF GND MOSI 4 7 5 FSB GND GND GND GND GND GND 5 8 2 U7B 4 6 5 RES1 R9 1k R15 1k R14 MC74HC4049 U7C MC74HC4049 GND MC74HC4049 U7A 2PTS 2 LEDV D7 LEDV D6 LEDV D5 VDD VPWR TP7 TSTPT VDD JMP2 FS0B R20 100k 1 GND GND GND GND GND GND 5 R19 10k TP6 TSTPT 5 8 5 8 5 8 GND GND 1 GND GND GND 2PTS JMP6 CSNS 6 GND 2 Number:1 GND J12 C16 1uF D8 LEDV 7 Sheet 1 of 1 Revision:3.0 GND R16 1k CONF0 C17 22nF GND 1 TP8 TSTPT 2 4 6 GND JUMP3 1 2 3 JMP4 1 J5 1 D9 LEDV GND GND JUMP3 1 2 3 JMP5 J4 SMA J3 SMA VDD RBAN1 51R GND GND 8 Error : FS_COLOR_LOGO_JPG.jpg file not found. GND R17 1k CONF1 J6 EM_2MM_JAUNE J2 SMA J1 SMA RBAN3 51R GND GND GND RBAN2 51RGND 8 EM_2MM_JAUNE 1 CBAN1 6.8nF 1 D4 GND MUR840 CBAN3 6.8nF R11 0R D3 GND MUR840 CBAN2 6.8nF R10 0R R12 0R J11 J10 IN1J VDD IN0J VDD JMP10 2PTS JMP1 2PTS VDD HEADER3X2 1 3 5 JP3 HEADER3X2 2 4 6 C9 22nF GND JP2 1 3 5 C8 22nF GND 7 18121C105KA VPWR 2 R23 RES1 R22 RES1 IN1 2 Application 2PTS JMP11 HS1 R7 2.2k IN0 2 2 HS0 R6 2.2k Version 4 April 2011 Date: 20-Aug-2013 Size: A3 Title SPD10 R21 1k_0.1% 1k R13 BANANA_RED GND BANANA_BLACK GND 2PTS JMP9 2PTS JMP8 2PTS JMP7 CN3 D11 LEDR 1 GND 1 GND 1 BANANA_RED CN2 GND D10 LEDR D2 LEDR D1 LEDR 1 BANANA_RED CN1 CN4 6 2 1 2 Freescale Semiconductor, Inc. 1 A B C D 6 8 1 Schematic Schematic Figure 16. Evaluation Board Schematic KT50XS4200UG Rev. 1.0 23 Board Layout 7 Board Layout 7.1 Silkscreen KT50XS4200UG Rev. 1.0 24 Freescale Semiconductor, Inc. Board Bill of Materials 8 Board Bill of Materials Table 8. Bill of Materials (1) Item Qty Schematic Label Value Description Part Number Assy Opt Active Components 1 1 U7 Buffer/Converter Hex Inv CMOS MC74HC4049 (2) 2 1 U1 Dual peripheral driver SN75451 (2) 3 1 U6 Freescale device MC50XS4200BEK (2) 4 1 U2 HFBR-2528 Fiber Optic Receiver 5 1 U3 HFBR-2528 Fiber Optic Receiver 6 1 U4 HFBR-2528 Fiber Optic Receiver 7 1 U5 HFBR-1528 Fiber Optic Transmitter Resistors 8 3 R10,R12,R11 0 Resistor 1%, SMD 9 5 R13,R17,R16,R14,R15 1.0 K Resistor 1%, SMD 10 1 R21 1.0 K Resistor 0,1%, SMD 11 2 R7,R6 2.2 K Resistor 1%, SMD 12 4 R2,R3,R4,R1 2.7 Resistor 1%, SMD 13 4 R18,R19,R25,R24 10 K Resistor 1%, SMD 14 1 R5 47 Resistor 1%, SMD 15 1 R20 100 K Resistor 1%, SMD Capacitors 16 2 C1, C16 1.0 F Capacitor Ceramic 50 V 17 6 C2, C3, C4, C5, C6, C7 100 nF Capacitor Ceramic 50 V 18 3 C8, C9, C17 22 nF Capacitor Ceramic 50 V 19 3 CBAN1, CBAN2, CBAN3 6.8 nF Capacitor Ceramic 50 V 4 D1, D2, D10, D11 LEDR Diode LED red Diodes 20 21 2 D3, D4 MUR840 Rectified diode 7.0 A, 400 V 22 5 D5, D6, D7, D8, D9 LEDV Diode LED green Notes 1. Freescale does not assume liability, endorse, or warrant components from external manufacturers are referenced in circuit drawings or tables. While Freescale offers component recommendations in this configuration, it is the customer’s responsibility to validate their application. 2. Critical components. For critical components, it is vital to use the manufacturer listed. KT50XS4200UG Rev. 1.0 Freescale Semiconductor, Inc. 25 References 9 References Following are URLs where you can obtain information on related Freescale products and application solutions: Freescale.com Support Pages Description URL KIT50XS4200EKEVB Tool Summary Page http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=KIT50XS4200EKEVB MC50XS4200 Product Summary Page http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=MC24XS4 KITUSBSPIEVME Tool Summary Page http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=KITUSBSPIEVME SPIGen Reference Product Summary Page http://www.freescale.com/webapp/sps/site/prod_summary.jsp?&code=SPIGEN 9.1 Support Visit www.freescale.com/support for a list of phone numbers within your region. 9.2 Warranty Visit www.freescale.com/warranty for a list of phone numbers within your region. KT50XS4200UG Rev. 1.0 26 Freescale Semiconductor, Inc. Revision History 10 Revision History Revision 1.0 Date 9/2014 Description of Changes • Initial Release KT50XS4200UG Rev. 1.0 Freescale Semiconductor, Inc. 27 How to Reach Us: Information in this document is provided solely to enable system and software implementers to use Freescale products. Home Page: freescale.com There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits based Web Support: freescale.com/support Freescale reserves the right to make changes without further notice to any products herein. Freescale makes no on the information in this document. warranty, representation, or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters that may be provided in Freescale data sheets and/or specifications can and do vary in different applications, and actual performance may vary over time. All operating parameters, including “typicals,” must be validated for each customer application by customer’s technical experts. Freescale does not convey any license under its patent rights nor the rights of others. Freescale sells products pursuant to standard terms and conditions of sale, which can be found at the following address: freescale.com/SalesTermsandConditions. Freescale and the Freescale logo are trademarks of Freescale Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off. SMARTMOS is a trademark of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. © 2014 Freescale Semiconductor, Inc. Document Number: KT50XS4200UG Rev. 1.0 9/2014