PHILIPS 74LVC1G384GV

74LVC1G384
Philips Semiconductors
Bilateral switch
74LVC1G384
Bilateral switch
Rev. 01 — 26 February 2004
Product data sheet
1. General description
The 74LVC1G384 is a high-speed Si-gate CMOS device.
The 74LVC1G384 provides an analog switch. The switch has input and output terminals
(pins Y and Z) and an active LOW enable input (pin E). When pin E is HIGH, the analog
switch is turned off.
2. Features
■ Very low ON-resistance:
◆ 7.5 Ω (typ) at VCC = 2.7 V
◆ 6.5 Ω (typ) at VCC = 3.3 V
◆ 6.0 Ω (typ) at VCC = 5 V.
■ ESD protection:
◆ HBM EIA/JESD22-A114-A exceeds 2 000 V
◆ MM EIA/JESD22-A115-A exceeds 200 V.
■ High noise immunity
■ CMOS low power consumption
■ Direct interface TTL-levels
■ Latch-up performance meets requirements of JESD78 Class I
■ Multiple package options
■ Specified from −40 °C to +80 °C and −40 °C to +125 °C.
3. Quick reference data
Table 1:
Quick reference data
Ground = 0 V; Tamb = 25 °C; tr = tf ≤ 3.0 ns.
Symbol
Parameter
Conditions
tPZH, tPZL
turn-on time E to Y or Z
CL = 50 pF; RL = 500 Ω
tPHZ, tPLZ
turn-off time E to Y or Z
Min
Typ
Max
Unit
VCC = 3.3 V
-
4.8
-
ns
VCC = 5.0 V
-
3.3
-
ns
-
5.4
-
ns
CL = 50 pF; RL = 500 Ω
VCC = 3.3 V
VCC = 5.0 V
CI
input capacitance
9397 750 12675
Product data sheet
-
3.6
-
ns
-
2
-
pF
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 26 February 2004
1 of 22
74LVC1G384
Philips Semiconductors
Bilateral switch
Table 1:
Quick reference data …continued
Ground = 0 V; Tamb = 25 °C; tr = tf ≤ 3.0 ns.
Symbol
CPD
Parameter
Conditions
power dissipation
capacitance
CL = 50 pF; fi = 10 MHz;
VCC = 3.3 V
switch capacitance
CS
[1]
Min
Typ
Max
Unit
-
15.2
-
pF
[2]
OFF-state
-
5
-
pF
ON-state
-
9.5
-
pF
[1]
CPD is used to determine the dynamic power dissipation (PD in µW).
PD = CPD × VCC2 × fi + (CL + CS)× VCC2 × fo where:
fi = input frequency in MHz;
fo = output frequency in MHz;
CL = output load capacitance in pF;
CS = maximum switch capacitance in pF;
VCC = supply voltage in V.
[2]
The condition is VI = GND to VCC.
4. Ordering information
Table 2:
Ordering information
Type number
Package
Description
Version
74LVC1G384GW −40 °C to +125 °C
Temperature range Name
-
plastic surface mounted package; 5 leads
SOT353
−40 °C to +125 °C
-
plastic surface mounted package; 5 leads
SOT753
74LVC1G384GV
5. Marking
Table 3:
Marking
Type number
Marking code
74LVC1G384GW
YL
74LVC1G384GV
YL
6. Functional diagram
Y
Z
1
1
4 #
E
1
2
X1
001aaa373
001aaa374
Fig 1. Logic symbol.
9397 750 12675
Product data sheet
Fig 2. IEC logic symbol.
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 26 February 2004
2 of 22
74LVC1G384
Philips Semiconductors
Bilateral switch
Z
Y
E
VCC
001aaa372
Fig 3. Logic diagram.
7. Pinning information
7.1 Pinning
Y 1
Z 2
GND
5 VCC
384
3
4
E
001aaa365
Fig 4. Pin configuration.
7.2 Pin description
Table 4:
Pin description
Pin
Symbol
Description
1
Y
independent input or output
2
Z
independent output or input
3
GND
ground (0 V)
4
E
enable input (active LOW)
5
VCC
supply voltage
8. Functional description
8.1 Function table
Table 5:
Function table [1]
Input E
Switch
L
ON-state
H
OFF-state
[1]
H = HIGH voltage level;
L = LOW voltage level.
9397 750 12675
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 26 February 2004
3 of 22
74LVC1G384
Philips Semiconductors
Bilateral switch
9. Limiting values
Table 6:
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to
GND (ground = 0 V).
Symbol
Parameter
Conditions
Min
Max
Unit
−0.5
+6.5
V
−0.5
+6.5
V
VCC
supply voltage
VI
input voltage
IIK
input diode current
VI < −0.5 V or
VI > VCC + 0.5 V
-
−50
mA
ISK
switch diode current
VI < −0.5 V or
VI > VCC + 0.5 V
-
±50
mA
VS
DC switch voltage
range
enable and disable mode
−0.5
VCC + 0.5 V
IS
DC switch source or
sink current
VS > −0.5 V or
VS < VCC + 0.5 V
-
±50
mA
ICC, IGND
VCC or GND current
-
±100
mA
Tstg
storage temperature
−65
+150
°C
Ptot
power dissipation
-
250
mW
[1]
[1]
Tamb = −40 ° C to +125 °C
The input and output voltage ratings may be exceeded if the input and output current ratings are observed.
10. Recommended operating conditions
Table 7:
Recommended operating conditions
Symbol
Parameter
VCC
supply voltage
VI
input voltage
VS
DC switch voltage range
Tamb
ambient temperature
tr, tf
input rise and fall times
[1]
Conditions
Min
Typ
Max
Unit
1.65
-
5.5
V
0
-
5.5
V
0
-
VCC
V
−40
-
+125
°C
VCC = 1.65 V to 2.7 V
0
-
20
ns/V
VCC = 2.7 V to 5.5 V
0
-
10
ns/V
[1]
To avoid drawing VCC current out of terminal Z, when switch current flows in terminal Y, the voltage drop
across the bidirectional switch must not exceed 0.4 V. If the switch current flows into terminal Z, no VCC
current will flow out of terminal Y. In this case there is no limit for the voltage drop across the switch.
9397 750 12675
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 26 February 2004
4 of 22
74LVC1G384
Philips Semiconductors
Bilateral switch
11. Static characteristics
Table 8:
Static characteristics
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Symbol
Parameter
Tamb = −40 °C to +85
VIH
VIL
Conditions
Min
Typ
Max
Unit
VCC = 1.65 V to 1.95 V
0.65 × VCC
-
-
V
VCC = 2.3 V to 2.7 V
1.7
-
-
V
VCC = 2.7 V to 3.6 V
2.0
-
-
V
VCC = 4.5 V to 5.5 V
0.7 × VCC
-
-
V
VCC = 1.65 V to 1.95 V
-
-
0.35 × VCC
V
VCC = 2.3 V to 2.7 V
-
-
0.7
V
VCC = 2.7 V to 3.6 V
-
-
0.8
V
°C [1]
HIGH-level input
voltage
LOW-level input
voltage
VCC = 4.5 V to 5.5 V
-
-
0.3 × VCC
V
-
±0.1
±5
µA
ILI
input leakage current
on control pin
VI = 5.5 V or GND; VCC = 5.5 V
[2]
IS(OFF)
analog switch
OFF-state current
VI = VIH or VIL; |VS| = VCC − GND;
VCC = 5.5 V; see Figure 5
[2]
-
±0.1
±5
µA
IS(ON)
analog switch
ON-state current
VI = VIH or VIL; |VS| = VCC − GND;
VCC = 5.5 V; see Figure 6
[2]
-
±0.1
±5
µA
ICC
quiescent supply
current
VI = VCC or GND; VS = GND or VCC;
IO = 0 A; VCC = 5.5 V
[2]
-
0.1
10
µA
∆ICC
additional quiescent
supply current per
control pin
VI = VCC − 0.6 V; VS = GND or VCC;
IO = 0 A; VCC = 5.5 V
[2]
-
5
500
µA
CI
input capacitance
-
2
-
pF
RON(peak)
switch ON-state
resistance (peak)
IS = 4 mA; VCC = 1.65 V to 1.95 V
-
35
130
Ω
IS = 8 mA; VCC = 2.3 V to 2.7 V
-
14
30
Ω
RON(rail)
switch ON-state
resistance rail
VI = GND to VCC; see Figure 7 and
Figure 8
IS = 12 mA; VCC = 2.7 V
-
11.5
25
Ω
IS = 24 mA; VCC = 3.0 V to 3.6 V
-
8.5
20
Ω
IS = 32 mA; VCC = 4.5 V to 5.5 V
-
6.5
15
Ω
VI = GND
IS = 4 mA; VCC = 1.65 V to 1.95 V
-
10
30
Ω
IS = 8 mA; VCC = 2.3 V to 2.7 V
-
8.5
20
Ω
IS = 12 mA; VCC = 2.7 V
-
7.5
18
Ω
IS = 24 mA; VCC = 3.0 V to 3.6 V
-
6.5
15
Ω
IS = 32 mA; VCC = 4.5 V to 5.5 V
-
6
10
Ω
IS = 4 mA; VCC = 1.65 V to 1.95 V
-
12
30
Ω
IS = 8 mA; VCC = 2.3 V to 2.7 V
-
8.5
20
Ω
VI = VCC
IS = 12 mA; VCC = 2.7 V
-
7.5
18
Ω
IS = 24 mA; VCC = 3.0 V to 3.6 V
-
6.5
15
Ω
IS = 32 mA; VCC = 4.5 V to 5.5 V
-
6
10
Ω
9397 750 12675
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 26 February 2004
5 of 22
74LVC1G384
Philips Semiconductors
Bilateral switch
Table 8:
Static characteristics …continued
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Symbol
RON(flat)
Parameter
switch ON-state
resistance flatness
Conditions
VI = GND to VCC; see Figure 9
IS = 4 mA; VCC = 1.8 V
Min
Typ
Max
Unit
-
100
-
Ω
[3]
IS = 8 mA; VCC = 2.5 V
-
17
-
Ω
IS = 12 mA; VCC = 2.7 V
-
10
-
Ω
IS = 24 mA; VCC = 3.3 V
-
5
-
Ω
IS = 32 mA; VCC = 5.0 V
-
3
-
Ω
VCC = 1.65 V to 1.95 V
0.65 × VCC
-
-
V
VCC = 2.3 V to 2.7 V
1.7
-
-
V
VCC = 2.7 V to 3.6 V
2.0
-
-
V
Tamb = −40 °C to +125 °C
VIH
VIL
HIGH-level input
voltage
LOW-level input
voltage
VCC = 4.5 V to 5.5 V
0.7 × VCC
-
-
V
VCC = 1.65 V to 1.95 V
-
-
0.35 × VCC
V
VCC = 2.3 V to 2.7 V
-
-
0.7
V
VCC = 2.7 V to 3.6 V
-
-
0.8
V
VCC = 4.5 V to 5.5 V
-
-
0.3 × VCC
V
ILI
input leakage current
on control pin
VI = 5.5 V or GND; VCC = 5.5 V
-
-
100
µA
IS(OFF)
analog switch
OFF-state current
VI = VIH or VIL; |VS| = VCC − GND;
VCC = 5.5 V; see Figure 5
-
-
200
µA
IS(ON)
analog switch
ON-state current
VI = VIH or VIL; |VS| = VCC − GND;
VCC = 5.5 V; see Figure 6
-
-
200
µA
ICC
quiescent supply
current
VI = VCC or GND; VS = GND or VCC;
IO = 0 A; VCC = 5.5 V
-
-
200
µA
∆ICC
additional quiescent
supply current per
control pin
VI = VCC − 0.6 V; VS = GND or VCC;
IO = 0 A; VCC = 5.5 V
-
-
5000
µA
RON(peak)
switch ON-state
resistance (peak)
VI = GND to VCC; see Figure 7
IS = 4 mA; VCC = 1.65 V to 1.95 V
-
-
180
Ω
IS = 8 mA; VCC = 2.3 V to 2.7 V
-
-
45
Ω
IS = 12 mA; VCC = 2.7 V
-
-
38
Ω
IS = 24 mA; VCC = 3.0 V to 3.6 V
-
-
30
Ω
IS = 32 mA; VCC = 4.5 V to 5.5 V
-
-
23
Ω
9397 750 12675
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 26 February 2004
6 of 22
74LVC1G384
Philips Semiconductors
Bilateral switch
Table 8:
Static characteristics …continued
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Symbol
Parameter
Conditions
RON(rail)
switch ON-state
resistance rail
VI = GND
IS = 4 mA; VCC = 1.65 V to 1.95 V
Min
Typ
Max
Unit
-
-
45
Ω
IS = 8 mA; VCC = 2.3 V to 2.7 V
-
-
30
Ω
IS = 12 mA; VCC = 2.7 V
-
-
27
Ω
IS = 24 mA; VCC = 3.0 V to 3.6 V
-
-
23
Ω
IS = 32 mA; VCC = 4.5 V to 5.5 V
-
-
15
Ω
IS = 4 mA; VCC = 1.65 V to 1.95 V
-
-
45
Ω
IS = 8 mA; VCC = 2.3 V to 2.7 V
-
-
30
Ω
IS = 12 mA; VCC = 2.7 V
-
-
27
Ω
IS = 24 mA; VCC = 3.0 V to 3.6 V
-
-
23
Ω
IS = 32 mA; VCC = 4.5 V to 5.5 V
-
-
15
Ω
VI = VCC
[1]
Typical values are measured at Tamb = 25 °C.
[2]
These typical values are measured at VCC = 3.3 V
[3]
These typical values are measured over the operating temperature range from −40 °C to +125 °C.
9397 750 12675
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 26 February 2004
7 of 22
74LVC1G384
Philips Semiconductors
Bilateral switch
VCC
VCC
E
VIH
IS
E
VIL
Y
Z
IS
IS
VO
VI
Y
Z
VO
VI
GND
GND
001aaa370
001aaa369
VI = VCC and VO = GND;
VI = VCC and VO = open circuit;
VI = GND and VO = VCC
VI = GND and VO = open circuit
Fig 5. Test circuit for measuring switch OFF-state
current.
Fig 6. Test circuit for measuring switch ON-state
current.
mna673
102
RON
(Ω)
VS
VCC = 1.8 V
VCC
VIL
E
2.5 V
2.7 V
10
Y
Z
IS
3.3 V
5.0 V
VI
GND
001aaa371
1
VI = GND to VCC; RON = VS/IS
Fig 7. Test circuit for measuring switch
ON-resistance.
0
2
3
4
VI (V)
5
VS = GND to VCC.
Fig 8. Typical switch ON-resistance as a function of
input voltage.
9397 750 12675
Product data sheet
1
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 26 February 2004
8 of 22
74LVC1G384
Philips Semiconductors
Bilateral switch
mna663
15
RON
(Ω)
RON
(Ω)
Tamb = +85 C
+25 C
−40 C
10
Tamb = +85 C
+25 C
−40 C
10
5
5
0
mna664
15
0
0
1
2
0
3
Vl (V)
a. VCC = 2.5 V
1
2
Vl (V)
3
b. VCC = 2.7 V
mna665
10
RON
(Ω)
Tamb =
8
mna666
8
RON
(Ω)
7
+85 C
6
+25 C
6
Tamb = +85 C
5
−40 C
+25 C
4
4
2
−40 C
3
2
0
0
c. VCC = 3.3 V
1
2
3
Vl (V)
4
0
1
2
3
4
VI (V)
5
d. VCC = 5.0 V
Fig 9. Switch ON-resistance at various supply voltages as a function of input voltage.
9397 750 12675
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 26 February 2004
9 of 22
74LVC1G384
Philips Semiconductors
Bilateral switch
12. Dynamic characteristics
Table 9:
Dynamic characteristics
At recommended operating conditions; voltages are referenced to GND (ground = 0 V); test circuit Figure 12.
Symbol
Parameter
Tamb = −40 °C to +85
tPHL, tPLH
tPZH, tPZL
Conditions
Min
Typ
Max
Unit
VCC = 1.65 V to 1.95 V
-
0.8
2.0
ns
VCC = 2.3 V to 2.7 V
-
0.4
1.2
ns
VCC = 2.7 V
-
0.4
1.0
ns
VCC = 3.0 V to 3.6 V
-
0.3
0.8
ns
VCC = 4.5 V to 5.5 V
-
0.2
0.6
ns
1.0
10.0
12.0
ns
°C [1]
propagation delay Y to Z
or Z to Y
turn-on time E to Y or Z
see Figure 10
[2]
see Figure 11
VCC = 1.65 V to 1.95 V
tPHZ, tPLZ
CPD
turn-off time E to Y or Z
power dissipation
capacitance
VCC = 2.3 V to 2.7 V
1.0
5.7
6.5
ns
VCC = 2.7 V
1.0
5.4
6.0
ns
VCC = 3.0 V to 3.6 V
1.0
4.8
5.0
ns
VCC = 4.5 V to 5.5 V
1.0
3.3
4.2
ns
VCC = 1.65 V to 1.95 V
1.0
7.4
10.0
ns
VCC = 2.3 V to 2.7 V
1.0
4.1
6.9
ns
VCC = 2.7 V
1.0
4.9
7.5
ns
VCC = 3.0 V to 3.6 V
1.0
5.4
6.5
ns
VCC = 4.5 V to 5.5 V
1.0
3.6
5.0
ns
see Figure 11
CL = 50 pF; fi = 10 MHz;
VI = GND to VCC
[3] [4]
VCC = 2.5 V
-
13.7
-
pF
VCC = 3.3 V
-
15.2
-
pF
VCC = 5.0 V
-
18.3
-
pF
VCC = 1.65 V to 1.95 V
-
-
3.0
ns
VCC = 2.3 V to 2.7 V
-
-
2.0
ns
VCC = 2.7 V
-
-
1.5
ns
VCC = 3.0 V to 3.6 V
-
-
1.5
ns
VCC = 4.5 V to 5.5 V
-
-
1.0
ns
1.0
-
15.5
ns
Tamb = −40 °C to +125 °C
tPHL, tPLH
tPZH, tPZL
propagation delay Y to Z
or Z to Y
turn-on time E to Y or Z
see Figure 10
see Figure 11
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
1.0
-
8.5
ns
VCC = 2.7 V
1.0
-
8.0
ns
VCC = 3.0 V to 3.6 V
1.0
-
6.5
ns
VCC = 4.5 V to 5.5 V
1.0
-
5.5
ns
9397 750 12675
Product data sheet
[2]
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 26 February 2004
10 of 22
74LVC1G384
Philips Semiconductors
Bilateral switch
Table 9:
Dynamic characteristics …continued
At recommended operating conditions; voltages are referenced to GND (ground = 0 V); test circuit Figure 12.
Symbol
Parameter
Conditions
tPHZ, tPLZ
turn-off time E to Y or Z
see Figure 11
VCC = 1.65 V to 1.95 V
Min
Typ
Max
Unit
1.0
-
13.0
ns
VCC = 2.3 V to 2.7 V
1.0
-
9.0
ns
VCC = 2.7 V
1.0
-
9.5
ns
VCC = 3.0 V to 3.6 V
1.0
-
8.5
ns
VCC = 4.5 V to 5.5 V
1.0
-
6.5
ns
[1]
All typical values are measured at Tamb = 25 °C.
[2]
tPHL and tPLH propagation delay is the calculated RC time constant of the typical switch ON-resistance of the switch and the specified
capacitance when driven by an ideal voltage source (zero output impedance).
[3]
CPD is used to determine the dynamic power dissipation (PD in µW).
PD = CPD × VCC2 × fi + (CL + CS)× VCC2 × fo where:
fi = input frequency in MHz;
fo = output frequency in MHz;
CL = output load capacitance in pF;
CS = maximum switch capacitance in pF;
VCC = supply voltage in V.
[4]
The condition is VI = GND to VCC.
13. Waveforms
VI
VM
Y or Z input
GND
t PHL
t PLH
VOH
VM
Z or Y output
VOL
mna667
Measurement points are given in Table 10.
Logic levels: VOL and VOH are typical output voltage drop that occur with the output load.
Fig 10. Input (Y or Z) to output (Z or Y) propagation delays.
Table 10:
Measurement points
Supply voltage
Input
Output
VCC
VM
VM
1.65 V to 1.95 V
0.5 × VCC
0.5 × VCC
2.3 V to 2.7 V
0.5 × VCC
0.5 × VCC
2.7 V
1.5 V
1.5 V
3.0 V to 3.6 V
1.5 V
1.5 V
4.5 V to 5.5 V
0.5 × VCC
0.5 × VCC
9397 750 12675
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 26 February 2004
11 of 22
74LVC1G384
Philips Semiconductors
Bilateral switch
VI
E
VM
GND
tPLZ
tPZL
VCC
Y or Z
output
LOW-to-OFF
OFF-to-LOW
VM
VX
VOL
tPHZ
VOH
Y or Z
tPZH
VY
output
HIGH-to-OFF
OFF-to-HIGH
VM
GND
switch
enabled
switch
disabled
switch
enabled
001aaa375
Measurement points are given in Table 11.
Logic levels: VOL and VOH are typical output voltage drop that occur with the output load.
Fig 11. Turn-on and turn-off times.
Table 11:
Measurement points
Supply voltage
Input
Output
VCC
VM
VM
VX
VY
1.65 V to 1.95 V
0.5 × VCC
0.5 × VCC
VOL + 0.1 × VCC
VOH − 0.1 × VCC
2.3 V to 2.7 V
0.5 × VCC
0.5 × VCC
VOL + 0.1 × VCC
VOH − 0.1 × VCC
2.7 V
1.5 V
1.5 V
VOL + 0.3 V
VOH − 0.3 V
3.0 V to 3.6 V
1.5 V
1.5 V
VOL + 0.3 V
VOH − 0.3 V
4.5 V to 5.5 V
0.5 × VCC
0.5 × VCC
VOL + 0.3 V
VOH − 0.3 V
9397 750 12675
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 26 February 2004
12 of 22
74LVC1G384
Philips Semiconductors
Bilateral switch
VEXT
VCC
PULSE
GENERATOR
VI
RL
VO
D.U.T.
CL
RT
RL
mna616
Test data is given in Table 12.
Definitions test circuit:
RT = Termination resistance should be equal to output impedance Zo of the pulse generator.
CL = Load capacitance including jig and probe capacitance.
RL = Load resistance.
VEXT = Test voltage for switching times.
Fig 12. Load circuitry for switching times.
Table 12:
Test data
Supply voltage
Input
Load
VCC
VI
tr, tf
1.65 V to 1.95 V
VCC
2.3 V to 2.7 V
VCC
2.7 V
CL
RL
tPLH, tPHL
tPZH, tPHZ
tPZL, tPLZ
≤ 2.0 ns 30 pF
1 kΩ
open
GND
2 × VCC
≤ 2.0 ns 30 pF
500 Ω
open
GND
2 × VCC
2.7 V
≤ 2.5 ns 50 pF
500 Ω
open
GND
6.0 V
3.0 V to 3.6 V
2.7 V
≤ 2.5 ns 50 pF
500 Ω
open
GND
6.0 V
4.5 V to 5.5 V
VCC
≤ 2.5 ns 50 pF
500 Ω
open
GND
2 × VCC
9397 750 12675
Product data sheet
VEXT
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 26 February 2004
13 of 22
74LVC1G384
Philips Semiconductors
Bilateral switch
14. Additional dynamic characteristics
Table 13: Additional dynamic characteristics
At recommended conditions; typical values measured at Tamb = 25 °C.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
dsin
sine-wave distortion
fi = 1 kHz; RL = 10 kΩ; CL = 50 pF;
see Figure 13
VCC = 1.65 V
-
0.032
-
%
VCC = 2.3 V
-
0.008
-
%
VCC = 3.0 V
-
0.006
-
%
VCC = 4.5 V
-
0.001
-
%
VCC = 1.65 V
-
0.068
-
%
VCC = 2.3 V
-
0.009
-
%
VCC = 3.0 V
-
0.008
-
%
-
0.006
-
%
VCC = 1.65 V
-
135
-
MHz
VCC = 2.3 V
-
145
-
MHz
VCC = 3.0 V
-
150
-
MHz
-
155
-
MHz
VCC = 1.65 V
-
>500
-
MHz
VCC = 2.3 V
-
>500
-
MHz
VCC = 3.0 V
-
>500
-
MHz
-
>500
-
MHz
VCC = 1.65 V
-
−46
-
dB
VCC = 2.3 V
-
−46
-
dB
VCC = 3.0 V
-
−46
-
dB
-
−46
-
dB
VCC = 1.65 V
-
−37
-
dB
VCC = 2.3 V
-
−37
-
dB
VCC = 3.0 V
-
−37
-
dB
VCC = 4.5 V
-
−37
-
dB
fi = 10 kHz; RL = 10 kΩ; CL = 50 pF;
see Figure 13
VCC = 4.5 V
fON-state(res)
switch ON-state
signal frequency
response
RL = 600 Ω; CL = 50 pF; fi = 1 MHz;
see Figure 14
[1]
VCC = 4.5 V
RL = 50 Ω; CL = 5 pF; fi = 1 MHz;
see Figure 14
[1]
VCC = 4.5 V
αOFF(ft)
switch OFF-state
signal feed-through
attenuation
RL = 600 Ω; CL = 50 pF; fi = 1 MHz;
see Figure 15
[2]
VCC = 4.5 V
RL = 50 Ω; CL = 5 pF; fi = 1 MHz;
see Figure 15
9397 750 12675
Product data sheet
[2]
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 26 February 2004
14 of 22
74LVC1G384
Philips Semiconductors
Bilateral switch
Table 13: Additional dynamic characteristics …continued
At recommended conditions; typical values measured at Tamb = 25 °C.
Symbol
Parameter
Conditions
Vct
crosstalk between
RL = 600 Ω; CL = 50 pF; fi = 1 MHz;
control input to signal tr = tf = 2 ns; see Figure 16
output
VCC = 1.65 V
frequency response
(−3 dB)
injection charge
Max
Unit
-
69
-
mV
-
87
-
mV
VCC = 3.0 V
-
156
-
mV
-
302
-
mV
VCC = 1.65 V
-
200
-
MHz
VCC = 2.3 V
-
350
-
MHz
VCC = 3.0 V
-
410
-
MHz
-
440
-
MHz
-
0.05
-
pC
RL = 50 Ω; CL = 10 pF; see Figure 14
[1]
VCC = 4.5 V
Q
Typ
VCC = 2.3 V
VCC = 4.5 V
fmax
Min
CL = 0.1 nF; Vgen = 0 V; Rgen = 0 Ω;
f = 1 MHz; RL = 1 MΩ;
VCC = 1.65 V to 5.5 V; see Figure 17
[3]
[1]
Adjust fi voltage to obtain 0 dBm level at output. Increase fi frequency until dB meter reads −3 dB.
[2]
Adjust fi voltage to obtain 0 dBm level at input.
[3]
Definition: Q = ∆Vout × CL. Guaranteed by design.
0.5 VCC
VCC
RL
VIL
E
Y or Z
fi
Z or Y
600 Ω
10 µF
CL
D
GND
001aaa366
Test conditions:
VCC = 1.65 V: Vi = 1.4 V (p-p).
VCC = 2.3 V: Vi = 2 V (p-p).
VCC = 3 V: Vi = 2.5 V (p-p).
VCC = 4 V: Vi = 4 V (p-p).
Fig 13. Test circuit for measuring sine-wave distortion.
9397 750 12675
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 26 February 2004
15 of 22
74LVC1G384
Philips Semiconductors
Bilateral switch
0.5 VCC
VCC
RL
VIL
0.1 µF
E
Y or Z
Z or Y
50 Ω
fi
CL
dB
GND
001aaa364
Fig 14. Test circuit for measuring the frequency response when switch is in ON-state.
0.5 VCC
0.5 VCC
VCC
RL
RL
VIH
0.1 µF
E
Y or Z
Z or Y
50 Ω
fi
CL
dB
GND
001aaa367
Fig 15. Test circuit for measuring feed-through attenuation when switch is in OFF-state.
0.5 VCC
0.5 VCC
VCC
Ri = 600 Ω
RL = 600 Ω
E
Y or Z
logic
input
Z or Y
CL =
50 pF
50 Ω
VO
GND
001aaa363
Fig 16. Test circuit for measuring crosstalk between control input and output.
9397 750 12675
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 26 February 2004
16 of 22
74LVC1G384
Philips Semiconductors
Bilateral switch
VCC
E
Y or Z
Z or Y
Rgen
logic
input
RL =
1 MΩ
Vgen
CL =
0.1 nF
VO
GND
001aaa362
logic
(E) off
input
on
VO
off
∆ VOUT
001aaa368
Fig 17. Test circuit for measuring injection charge.
9397 750 12675
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 26 February 2004
17 of 22
74LVC1G384
Philips Semiconductors
Bilateral switch
15. Package outline
Plastic surface mounted package; 5 leads
SOT353
D
E
B
y
X
A
HE
5
v M A
4
Q
A
A1
1
2
e1
3
bp
c
Lp
w M B
e
detail X
0
1
2 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A
A1
max
bp
c
D
E (2)
e
e1
HE
Lp
Q
v
w
y
mm
1.1
0.8
0.1
0.30
0.20
0.25
0.10
2.2
1.8
1.35
1.15
1.3
0.65
2.2
2.0
0.45
0.15
0.25
0.15
0.2
0.2
0.1
OUTLINE
VERSION
REFERENCES
IEC
SOT353
JEDEC
EIAJ
SC-88A
EUROPEAN
PROJECTION
ISSUE DATE
97-02-28
Fig 18. Package outline SOT353.
9397 750 12675
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 26 February 2004
18 of 22
74LVC1G384
Philips Semiconductors
Bilateral switch
Plastic surface mounted package; 5 leads
SOT753
D
E
B
y
A
X
HE
5
v M A
4
Q
A
A1
c
1
2
3
Lp
detail X
bp
e
w M B
0
1
2 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A
A1
bp
c
D
E
e
HE
Lp
Q
v
w
y
mm
1.1
0.9
0.100
0.013
0.40
0.25
0.26
0.10
3.1
2.7
1.7
1.3
0.95
3.0
2.5
0.6
0.2
0.33
0.23
0.2
0.2
0.1
OUTLINE
VERSION
REFERENCES
IEC
SOT753
JEDEC
JEITA
SC-74A
EUROPEAN
PROJECTION
ISSUE DATE
02-04-16
Fig 19. Package outline SOT753.
9397 750 12675
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 26 February 2004
19 of 22
74LVC1G384
Philips Semiconductors
Bilateral switch
16. Revision history
Table 14:
Revision history
Document ID
Release date
Data sheet status
Change notice
Order number
Supersedes
74LVC1G384_1
20040226
Product data
-
9397 750 12675
-
9397 750 12675
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 26 February 2004
20 of 22
74LVC1G384
Philips Semiconductors
Bilateral switch
17. Data sheet status
Level
Data sheet status [1]
Product status [2] [3]
Definition
I
Objective data
Development
This data sheet contains data from the objective specification for product development. Philips
Semiconductors reserves the right to change the specification in any manner without notice.
II
Preliminary data
Qualification
This data sheet contains data from the preliminary specification. Supplementary data will be published
at a later date. Philips Semiconductors reserves the right to change the specification without notice, in
order to improve the design and supply the best possible product.
III
Product data
Production
This data sheet contains data from the product specification. Philips Semiconductors reserves the
right to make changes at any time in order to improve the design, manufacturing and supply. Relevant
changes will be communicated via a Customer Product/Process Change Notification (CPCN).
[1]
Please consult the most recently issued data sheet before initiating or completing a design.
[2]
The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at
URL http://www.semiconductors.philips.com.
[3]
For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status.
18. Definitions
19. Disclaimers
Short-form specification — The data in a short-form specification is
extracted from a full data sheet with the same type number and title. For
detailed information see the relevant data sheet or data handbook.
Life support — These products are not designed for use in life support
appliances, devices, or systems where malfunction of these products can
reasonably be expected to result in personal injury. Philips Semiconductors
customers using or selling these products for use in such applications do so
at their own risk and agree to fully indemnify Philips Semiconductors for any
damages resulting from such application.
Limiting values definition — Limiting values given are in accordance with
the Absolute Maximum Rating System (IEC 60134). Stress above one or
more of the limiting values may cause permanent damage to the device.
These are stress ratings only and operation of the device at these or at any
other conditions above those given in the Characteristics sections of the
specification is not implied. Exposure to limiting values for extended periods
may affect device reliability.
Application information — Applications that are described herein for any
of these products are for illustrative purposes only. Philips Semiconductors
make no representation or warranty that such applications will be suitable for
the specified use without further testing or modification.
Right to make changes — Philips Semiconductors reserves the right to
make changes in the products - including circuits, standard cells, and/or
software - described or contained herein in order to improve design and/or
performance. When the product is in full production (status ‘Production’),
relevant changes will be communicated via a Customer Product/Process
Change Notification (CPCN). Philips Semiconductors assumes no
responsibility or liability for the use of any of these products, conveys no
licence or title under any patent, copyright, or mask work right to these
products, and makes no representations or warranties that these products are
free from patent, copyright, or mask work right infringement, unless otherwise
specified.
20. Contact information
For additional information, please visit http://www.semiconductors.philips.com
For sales office addresses, send an email to: [email protected]
9397 750 12675
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 26 February 2004
21 of 22
74LVC1G384
Philips Semiconductors
Bilateral switch
21. Contents
1
2
3
4
5
6
7
7.1
7.2
8
8.1
9
10
11
12
13
14
15
16
17
18
19
20
General description . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Quick reference data . . . . . . . . . . . . . . . . . . . . . 1
Ordering information . . . . . . . . . . . . . . . . . . . . . 2
Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Functional diagram . . . . . . . . . . . . . . . . . . . . . . 2
Pinning information . . . . . . . . . . . . . . . . . . . . . . 3
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3
Functional description . . . . . . . . . . . . . . . . . . . 3
Function table . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 4
Recommended operating conditions. . . . . . . . 4
Static characteristics. . . . . . . . . . . . . . . . . . . . . 5
Dynamic characteristics . . . . . . . . . . . . . . . . . 10
Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Additional dynamic characteristics . . . . . . . . 14
Package outline . . . . . . . . . . . . . . . . . . . . . . . . 18
Revision history . . . . . . . . . . . . . . . . . . . . . . . . 20
Data sheet status . . . . . . . . . . . . . . . . . . . . . . . 21
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Contact information . . . . . . . . . . . . . . . . . . . . 21
© Koninklijke Philips Electronics N.V. 2004
All rights are reserved. Reproduction in whole or in part is prohibited without the prior
written consent of the copyright owner. The information presented in this document does
not form part of any quotation or contract, is believed to be accurate and reliable and may
be changed without notice. No liability will be accepted by the publisher for any
consequence of its use. Publication thereof does not convey nor imply any license under
patent- or other industrial or intellectual property rights.
Date of release: 26 February 2004
Document order number: 9397 750 12675
Published in The Netherlands