PHILIPS PDI1394P22

INTEGRATED CIRCUITS
PDI1394P22
3-port physical layer interface
Objective specification
1999 Jul 09
Philips Semiconductors
Objective specification
3-port physical layer interface
PDI1394P22
1.0 FEATURES
• Fully supports provisions of IEEE 1394–1995 Standard for high
• Supports extended bias-handshake time for enhanced
performance serial bus and the P1394a supplement (Version 2.0)1
interoperability with camcorders
• Full P1394a support includes:
• Interface to link-layer controller supports low-cost bus-holder
isolation and optional Annex J electrical isolation
– Connection debounce
• Data interface to link-layer controller through 2/4/8 parallel lines at
– Arbitrated short reset
49.152 MHz
– Multispeed concatenation
• Low-cost 24.576 MHz crystal provides transmit, receive data at
– Arbitration acceleration
– Fly-by concatenation
100/200/400 Mbits/s, and link-layer controller clock at 49.152 MHz
• Does not require external filter capacitors for PLL
• Interoperable with link-layer controllers using 3.3 V and 5 V
– Port disable/suspend/resume
• Provides three 1394a fully-compliant cable ports at
100/200/400 Megabits per second (Mbits/s)
supplies
• Fully compliant with Open HCI requirements
• Cable ports monitor line conditions for active connection to remote
• Interoperable with other Physical Layers (PHYs) using 3.3 V and
5 V supplies
• Node power class information signaling for system power
node.
• Power down features to conserve energy in battery-powered
management
• Cable power presence monitoring
• Separate cable bias (TPBIAS) for each port
• Register bits give software control of contender bit, power class
applications include:
– Automatic device power down during suspend
– Device power down terminal
– Link interface disable via LPS
– Inactive ports powered-down
bits, link active bit, and 1394a features
• Logic performs system initialization and arbitration functions
• Encode and decode functions included for data-strobe bit level
• Fully interoperable with FireWire implementation of IEEE Std 1394
• Function and pin compatible with the Lucent FW803 400 Mbps Phy
encoding
• Incoming data resynchronized to local clock
• Single 3.3 volt supply operation
• Minimum VDD of 2.7 V for end-of-wire power-consuming devices
• While unpowered and connected to the bus, will not drive TPBIAS
2.0 DESCRIPTION
The PDI1394P22 provides the digital and analog transceiver functions
needed to implement a three port node in a cable-based IEEE
1394–1995 and/or 1394a network. Each cable port incorporates two
differential line transceivers. The transceivers include circuitry to
monitor the line conditions as needed for determining connection
status, for initialization and arbitration, and for packet reception and
transmission. The PDI1394P22 is designed to interface with a Link
Layer Controller (LLC), such as the PDI1394L11 or PDI1394L21.
on a connected port, even if receiving incoming bias voltage on
that port
3.0 ORDERING INFORMATION
PACKAGE
64-pin plastic LQFP
1.
TEMPERATURE RANGE
OUTSIDE NORTH AMERICA
NORTH AMERICA
PKG. DWG. #
0°C to +70°C
PDI1394P22 BD
PDI1394P22 BD
SOT314-2
Implements technology covered by one or more patents of Apple Computer, Incorporated and SGS Thompson, Limited.
1999 Jul 09
2
Philips Semiconductors
Objective specification
3-port physical layer interface
PDI1394P22
DGND
SYSCLK
DVDD
/RESET
XO
XI
PLLGND
PLLVDD
DGND
R1
R0
AGND
AGND
AVDD
AVDD
AGND
4.0 PIN CONFIGURATION
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
LREQ
1
48
TPBIAS2
DGND
2
47
TPA2+
CTL0
3
46
TPA2–
CTL1
4
45
TPB2+
D0
5
44
TPB2–
D1
6
43
AVDD
DVDD
7
42
TPBIAS1
D2
8
41
TPA1+
PDI1394P22
35
TPA0–
15
34
TPB0+
LPS
16
33
TPB0–
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
AGND
14
CNA
AVDD
DGND
AVDD
TPA0+
TEST0
TPBIAS0
36
TEST1
37
13
DVDD
12
D7
DVDD
D6
CPS
TPB1–
DGND
38
PC2
11
/ISO
D5
PC1
TPB1+
PD
TPA1–
39
PC0
40
10
DVDD
9
D4
C/LKON
D3
SV001782
5.0 PIN DESCRIPTION
I/O
Description
AGND
Name
Supply
32, 49, 52, 53
—
Analog circuit ground terminals. These terminals should be tied together
to the low impedance circuit board ground plane.
AVDD
Supply
30, 31, 43, 50, 51
—
Analog circuit power terminals. A combination of high frequency
decoupling capacitors near each terminal are suggested, such as
paralleled 0.1 µF and 0.001 µF. Lower frequency 10 µF filtering
capacitors are also recommended. These supply terminals are
separated from PLLVDD and DVDD internal to the device to provide
noise isolation. They should be tied at a low impedance point on the
circuit board.
CNA
CMOS
15
O
Cable Not Active output. This terminal is asserted high when there are
no ports receiving incoming bias voltage.
CPS
CMOS
24
I
Cable Power Status input. This terminal is normally connected to cable
power through a 370–410 kΩ resistor. This circuit drives an internal
comparator that is used to detect the presence of cable power.
CMOS 5V tol
3, 4
I/O
CTL0,
CTL1
1999 Jul 09
Pin Type
Pin Numbers
Control I/Os. These bi-directional signals control communication
between the PDI1394P22 and the LLC. Bus holders are built into
these terminals.
3
Philips Semiconductors
Objective specification
3-port physical layer interface
Name
C/LKON
Pin Type
CMOS 5V tol
Pin Numbers
18
PDI1394P22
I/O
Description
I/O
Bus Manager Contender programming input and link-on output. On
hardware reset, this terminal is used to set the default value of the
contender status indicated during self-ID. Programming is done by tying
the terminal through a 10kΩ resistor to a high (contender) or low (not
contender). The resistor allows the link-on output to override the input.
Following hardware reset, this terminal is the link-on output, which is
used to notify the LLC to power-up and become active. The link-on
output is a square-wave signal with a period of approximately 163 ns (8
SYSCLK cycles) when active. The link-on output is deasserted low when
the LPS input terminal is active.
DGND
Supply
2, 14, 25, 56, 64
—
Digital circuit ground terminals. These terminals should be tied together
to the low impedance circuit board ground plane.
D0–D7
CMOS 5V tol
5, 6, 8, 9, 10, 11,
12, 13
I/O
Data I/Os. These are bi-directional data signals between the
PDI1394P22 and the LLC. Bus holders are built into these terminals.
DVDD
Supply
7, 17, 26, 27, 62
—
Digital circuit power terminals. A combination of high frequency
decoupling capacitors near each terminal are suggested, such as
paralleled 0.1 µF and 0.001 µF. Lower frequency 10 µF filtering
capacitors are also recommended. These supply terminals are
separated from PLLVDD and AVDD internal to the device to provide
noise isolation. They should be tied at a low impedance point on the
circuit board.
/ISO
CMOS
23
I
Link interface isolation control input. This terminal controls the operation
of output differentiation logic on the CTL and D terminals. If an optional
isolation barrier of the type described in Annex J of IEEE Std 1394–1395
is implemented between the PDI1394P22 and LLC, the /ISO terminal
should be tied low to enable the differentiation logic. If no isolation barrier
is implemented (direct connection), or bus holder isolation is
implemented, the /ISO terminal should be tied high to disable the
differentiation logic.
LPS
CMOS 5V tol
16
I
Link Power Status input. This terminal is used to monitor the power
status of the LLC, and is connected to either the VDD supplying the link
layer controller through a 1kΩ resistor, or to a pulsed output which is
active when the LLC is powered. The pulsed output is useful when using
an isolation barrier. If this input is low for more than 25 ms, the LLC is
considered powered down. If this input is high for more than 20 ns, the
LLC is considered powered up. If the LLC is powered-down, the
PHY–LLC interface is disabled, and the PDI1394P22 performs only the
basic repeater functions required for network initialization and operation.
Bus holder is built into this terminal.
LREQ
CMOS 5V tol
1
I
LLC Request input. The LLC uses this input to initiate a service request
to the PDI1394P22. Bus holder is built into this terminal.
PC0, PC1,
PC2
CMOS 5V tol
20, 21, 22
I
Power Class programming inputs. On hardware reset, these inputs set
the default value of the power class indicated during self-ID.
Programming is done by tying the terminals high or low. Refer to
Table 18 for encoding.
PD
CMOS 5V tol
19
I
Power Down input. A logic high on this terminal turns off all internal
circuitry except the cable-active monitor circuits which control the CNA
output. Bus holder is built into this terminal. For more information, refer to
Section 17.3
PLLGND
Supply
58
—
PLL circuit ground terminals. These terminals should be tied together to
the low impedance circuit board ground plane.
PLLVDD
Supply
57
—
PLL circuit power terminals. A combination of high frequency decoupling
capacitors near each terminal are suggested, such as paralleled 0.1 µF
and 0.001 µF. Lower frequency 10 µF filtering capacitors are also
recommended. These supply terminals are separated from DVDD and
AVDD internal to the device to provide noise isolation. They should be
tied at a low impedance point on the circuit board.
/RESET
CMOS 5V tol
61
I
Logic reset input. Asserting this terminal low resets the internal logic. An
internal pull-up resistor to VDD is provided so only an external
delay capacitor in parallel with a resistor is required for proper power-up
operation. For more information, refer to Section 17.3. This input is
otherwise a standard logic input, and can also be driven by an
open-drain type driver.
1999 Jul 09
4
Philips Semiconductors
Objective specification
3-port physical layer interface
Name
R0, R1
Pin Type
Bias
Pin Numbers
PDI1394P22
I/O
Description
54, 55
—
Current setting resistor terminals. These terminals are connected to
an external resistance to set the internal operating currents and
cable driver output currents. A resistance of 6.34 kΩ ±1% is required to
meet the IEEE Std 1394–1995 output voltage limits.
SYSCLK
CMOS
63
O
System clock output. Provides a 49.152 MHz clock signal, synchronized
with data transfers, to the LLC.
TEST0
CMOS
29
I
Test control input. This input is used in manufacturing tests of the
PDI1394P22. For normal use, this terminal should be tied to GND.
TEST1
CMOS
28
I
Test control input. This input is used in manufacturing tests of the
PDI1394P22. For normal use, this terminal should be tied to GND.
TPA0+,
TPA1+,
TPA2+
Cable
36, 41, 47
TPA0–,
TPA1–,
TPA2–
Cable
35, 40, 46
I/O
TPB0+,
TPB1+,
TPB2+
Cable
34, 39, 45
I/O
TPB0–,
TPB1–,
TPB2–
Cable
33, 38, 44
I/O
TPBIAS0,
TPBIAS1,
TPBIAS2
Cable
37, 42, 48
I/O
Twisted-pair bias output. This provides the 1.86V nominal bias voltage
needed for proper operation of the twisted-pair cable drivers and
receivers, and for signaling to the remote nodes that there is an active
cable connection. Each of these terminals must be decoupled with a
0.3 µF–1 µF capacitor to ground.
XO, XI
Crystal
60, 59
—
Crystal oscillator inputs. These terminals connect to a 24.576 MHz
parallel resonant fundamental mode crystal. The optimum values for the
external shunt capacitors are dependent on the specifications of the
crystal used. Can also be driven by an external clock generator (leave
XO unconnected in this case).
1999 Jul 09
I/O
Twisted-pair cable A differential signal terminals. Board traces from each
g
differential signal
g
terminals should be kept
pair of positive and negative
matched and as short as possible to the external load resistors and to
the cable connector.
Twisted-pair cable B differential signal terminals. Board traces from each
pair of positive and negative
g
differential signal
g
terminals should be kept
matched and as short as possible to the external load resistors and to
the cable connector.
5
Philips Semiconductors
Objective specification
3-port physical layer interface
PDI1394P22
6.0 BLOCK DIAGRAM
CPS
LPS
RECEIVED DATA
DECODER/
RETIMER
/ISO
CABLE POWER
DETECTOR
CPS
C/LKON
SYSCLK
LREQ
CTL0
CTL1
D0
CABLE PORT 0
LINK
INTERFACE
I/O
TPA0+
TPA0–
D1
D2
D3
D4
D5
D6
D7
ARBITRATION
AND CONTROL
STATE MACHINE
LOGIC
TPB0+
TPB0–
PC0
PC1
TPA1+
TPA1–
PC2
CNA
CABLE PORT 1
R0
R1
CABLE PORT 2
TPBIAS0
TPBIAS1
TPBIAS2
TPA2+
TPA2–
TPB2+
TPB2–
BIAS VOLTAGE
AND
CURRENT
GENERATOR
PD
/RESET
TPB1+
TPB1–
CRYSTAL
OSCILLATOR,
PLL SYSTEM,
AND CLOCK
GENERATOR
XI
XO
TRANSMIT
DATA
ENCODER
SV01743
7.0 FUNCTIONAL SPECIFICATION
section 5.9.4. To operate with single capacitor (bus holder) isolation,
the /ISO on the PHY terminal must be tied high.
The PDI1394P22 requires only an external 24.576 MHz crystal as a
reference. An external clock can be provided instead of a crystal. An
internal oscillator drives an internal phase-locked loop (PLL), which
generates the required 393.216 MHz reference signal. This
reference signal is internally divided to provide the clock signals
used to control transmission of the outbound encoded Strobe and
Data information. A 49.152 MHz clock signal, supplied to the
associated LLC for synchronization of the two chips, is used for
resynchronization of the received data. The Power Down (PD)
function, when enabled by asserting the PD terminal high, stops
operation of the PLL and disables all circuits except the cable bias
detectors at the TPB terminals. The port transmitter circuitry and the
receiver circuitry are also disabled when the port is disabled,
suspended, or disconnected.
Data bits to be transmitted through the cable ports are received from
the LLC on two, four or eight parallel paths (depending on the
requested transmission speed). They are latched internally in the
PDI1394P22 in synchronization with the 49.152 MHz system clock.
These bits are combined serially, encoded, and transmitted at
98.304/196.608/392.216 Mbits/s (referred to as S100, S200, and
S400 speed, respectively) as the outbound data-strobe information
stream. During transmission, the encoded data information is
transmitted differentially on the TPB cable pair(s), and the encoded
strobe information is transmitted differentially on the TPA cable
pair(s).
During packet reception the TPA and TPB transmitters of the
receiving cable port are disabled, and the receivers for that port are
enabled. The encoded data information is received on the TPA cable
pair, and the encoded strobe information is received on the TPB
cable pair. The received data-strobe information is decoded to
recover the receive clock signal and the serial data bits. The serial
The PDI1394P22 supports an optional isolation barrier between
itself and its LLC. When the /ISO input terminal is tied high, the
LLC interface outputs behave normally. When the /ISO terminal is
tied low, internal differentiating logic is enabled, and the outputs are
driven such that they can be coupled through a capacitive or
transformer galvanic isolation barrier as described in IEEE 1394a
1999 Jul 09
6
Philips Semiconductors
Objective specification
3-port physical layer interface
PDI1394P22
hard-wired high or low as a function of the equipment design. The
PC0–PC2 terminals are used to indicate the default power-class
status for the node (the need for power from the cable or the ability
to supply power to the cable). See Table 18 for power class
encoding. The C/LKON terminal is used as an input to indicate that
the node is a contender for bus manager.
data bits are split into two-, four- or eight-bit parallel streams
(depending upon the indicated receive speed), resynchronized to
the local 49.152 MHz system clock and sent to the associated LLC.
The received data is also transmitted (repeated) on the other active
(connected) cable ports.
Both the TPA and TPB cable interfaces incorporate differential
comparators to monitor the line states during initialization and
arbitration. The outputs of these comparators are used by the
internal logic to determine the arbitration status. The TPA channel
monitors the incoming cable common-mode voltage. The value of
this common-mode voltage is used during arbitration to set the
speed of the next packet transmission (speed signalling). In addition,
the TPB channel monitors the incoming cable common-mode
voltage on the TPB pair for the presence of the remotely supplied
twisted-pair bias voltage (cable bias detection).
The PHY supports suspend/resume as defined in the IEEE 1394a
specification. The suspend mechanism allows pairs of directly
connected ports to be placed into a low power state while
maintaining a port-to-port connection between 1394 bus segments.
While in a low power state, a port is unable to transmit or receive
data transaction packets. However, a port in a low power state is
capable of detecting connection status changes and detecting
incoming TPBIAS. When all three ports of the PDI1394P22 are
suspended, all circuits except the bias-detection circuits are
powered down, resulting in significant power savings. The TPBIAS
circuit monitors the value of incoming TPA pair common-mode
voltage when local TPBIAS is inactive. Because this circuit has an
internal current source and the connected node has a current sink,
the monitored value indicates the cable connection status. This
monitor is called connect-detect.
The PDI1394P22 provides a 1.86 V nominal bias voltage at the
TPBIAS terminal for port termination. the PHY contains three
independent TPBIAS circuits. This bias voltage, when seen through
a cable by a remote receiver, indicates the presence of an active
connection. This bias voltage source must be stabilized by an
external filter capacitor of 0.3 µF–1 µF.
Both the cable bias-detect monitor and TPBIAS connect-detect
monitor are used in suspend/resume signaling and cable connection
detection. For additional details of suspend/resume operation, refer
to the 1394a specification. The use of suspend/resume is
recommended for new designs.
The line drivers in the PDI1394P22 operate in a high-impedance
current mode, and are designed to work with external 112 Ω
line-termination resistor networks in order to match the 110 Ω cable
impedance. One network is provided at each end of all twisted-pair
cable. Each network is composed of a pair of series-connected 56 Ω
resistors. The midpoint of the pair of resistors that is directly
connected to the twisted-pair A terminals is connected to its
corresponding TPBIAS voltage terminal. The midpoint of the pair of
resistors that is directly connected to the twisted-pair B terminals is
coupled to ground through a parallel R-C network with recommended
values of 5 kΩ and 220 pF. The values of the external line termination
resistors are designed to meet the standard specifications when
connected in parallel with the internal receiver circuits. An external
resistor connected between the R0 and R1 terminals sets the driver
output current, along with other internal operating currents. This
current setting resistor has a value of 6.34 kΩ ±1%.
The port transmitter and receiver circuitry is disabled during power
down (when the PD input terminal is asserted high), during reset
(when the /RESET input terminal is asserted low), when no active
cable is connected to the port, or when controlled by the internal
arbitration logic. The port twisted-pair bias voltage circuitry is
disabled during power down, during reset, or when the port is
disabled as commanded by the LLC.
The CNA (cable-not-active) terminal provides a high output when all
twisted-pair cable ports are disconnected, and can be used along
with LPS to determine when to power down the PDI1394P22. The
CNA output is not debounced. In Power Down mode, the CNA
detection circuitry remains enabled.
When the power supply of the PDI1394P22 is removed while the
twisted-pair cables are connected, the PDI1394P22 transmitter and
receiver circuitry presents a high impedance to the cable in order to
not load the TPBIAS voltage on the other end of the cable.
The LPS (link power status) terminal works with the C/LKON
terminal to manage the power usage in the node. The LPS signal
from the LLC indicates to the PHY that the LLC is powered up and
active. During LLC Power Down mode, as indicated by the LPS
input being low for more than 25 µs, the PDI1394P22 deactivates
the PHY-LLC interface to save power. The PDI1394P22 continues
the necessary repeater function required for network operation
during this low power state.
When the PDI1394P22 is used with one or more of the ports not
brought out to a connector, the twisted-pair terminals of the unused
ports must be terminated for reliable operation. For each unused
port, the TPB+ and TPB– terminals can be tied together and then
pulled to ground, or the TPB+ and TPB– terminals can be connected
to the suggested termination network. The TPA+ and TPA– and
TPBIAS terminals of an unused port can be left unconnected.
If the PHY receives a link-on packet from another node, the C/LKON
terminal is activated to output a square-wave signal. The LLC
recognizes this signal, reactivates any powered-down portions of the
LLC, and notifies the PHY of its power-on status via the LPS
terminal. The PHY confirms notification by deactivating the
square-wave signal on the C/LKON terminal, then enables the
PHY-link interface.
The TEST0 and TEST1 terminals are used to set up various
manufacturing test conditions. For normal operation, the TEST0 and
TEST1 terminals should be connected to ground.
Four package terminals, used as inputs to set the default value for
four configuration status bits in the self-ID packet, should be
1999 Jul 09
7
Philips Semiconductors
Objective specification
3-port physical layer interface
PDI1394P22
8.0 ABSOLUTE MAXIMUM RATINGS 1
In accordance with the Absolute Maximum Rating System (IEC 134). Voltages are referenced to GND (ground = 0 V).
LIMITS
SYMBOL
VDD
VI
VI–5V
VO
PARAMETER
CONDITION
MIN
MAX
UNIT
DC supply voltage
–0.5
4.0
V
DC input voltage
–0.5
VDD+0.5
V
5 volt tolerant input voltage range
–0.5
5.5
V
–0.5
VDD+0.5
V
2
kV
DC output voltage range at any output
Human Body Model
Electrostatic discharge
Tamb
Operating free-air temperature range
Tstg
Storage temperature range
Machine Model
200
V
0
+70
°C
–65
+150
°C
NOTE:
1. Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under “Recommended Operating
Conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
9.0 RECOMMENDED OPERATING CONDITIONS
SYMBOL
VDD
PARAMETER
Supply voltage
MIN
TYP
MAX
UNIT
Source power node
3.0
3.3
3.6
V
Non-source power node
2.7 1
3.0
3.6
V
/ISO = VDD, VDD = 2.7 V
2.3
5.5
V
/ISO = VDD, VDD >= 3.0 V
2.6
5.5
V
0.7
V
VIH
High-level
g
input voltage,
g , pins
CTLn, Dn, C/LKON 2
VIL
Low-level input voltage, pins
CTLn, Dn, C/LKON 2
/ISO = VDD
Output current, pins CTLn, Dn,
C/LKON and SYSCLK
VOH = VDD –0.5 V, VOL = 0.5 V
–12
12
mA
IO
Output current
TPBIAS outputs
–6
2.5
mA
VID
Differential input voltage amplitude
TPA, TPB cable inputs, during data reception
118
260
mV
TPA, TPB cable inputs, during data arbitration
168
265
mV
1.165
2.515
V
Non-source power node
1.165
2.015 1
V
Source power node
0.935
2.515
V
Non-source power node
0.935
2.015 1
V
Source power node
0.523
2.515
V
Non-source power node
0.523
2.015 1
IOH/IOL
VIC-100
C
TPB common-mode
common mode input voltage
Speed signalling
g
g off
or S100 speed signal
Source power node
VIC-200
C
TPB common
common-mode
mode input voltage
S200 speed signal
VIC-100
C
TPB common
common-mode
mode input voltage
S400 speed signal
Power–up reset time
Set by capacitor between /RESET pin and GND
tPU
Receive input jitter
Receive input skew
fXTAL
Crystal or external clock frequency
2
TPA, TPB cable inputs, S100 operation
1.08
ns
TPA, TPB cable inputs, S200 operation
0.5
ns
TPA, TPB cable inputs, S400 operation
0.315
ns
Between TPA and TPB cable inputs, S00 operation
0.8
ns
Between TPA and TPB cable inputs, S200 operation
0.55
ns
Between TPA and TPB cable inputs, S400 operation
0.5
ns
24.5785
MHz
Crystal connected according to Figure 8 or external
clock input at pin XI
24.5735
NOTES:
1. For a node that does not source power to the bus (see Section 4.2.2.2 in the IEEE 1394-1995 standard).
2. C/LKON is only an input when /RESET = 0.
1999 Jul 09
V
ms
8
24.576
Philips Semiconductors
Objective specification
3-port physical layer interface
PDI1394P22
10.0 CABLE DRIVER
SYMBOL
PARAMETER
TEST CONDITION
LIMITS
MIN
TYP
MAX
UNIT
Differential output voltage
56 Ω load
172
265
mV
IO(diff)
Driver Difference current, TPA+, TPA–, TPB+, TPB– 1
Drivers enabled,
speed signaling OFF
–1.051
0.881
mA
100 Mbit/s speed signaling enabled
–0.81
–0.44
mA
ISP
Common mode speed signaling current, TPB+, TPB– 2
200 Mbit/s speed signaling enabled
–4.84
–2.53
mA
400 Mbit/s speed signaling enabled
–12.4
–8.10
mA
20
mV
VOD
VOFF
OFF state differential voltage
Drivers disabled
NOTES:
1. Limits defined as algebraic sum of TPA+ and TPA– driver currents. Limits also apply to TPB+ and TPB– algebraic sum of driver currents.
2. Limits defined as absolute limit of each of TPB+ and TPB– driver currents.
11.0 CABLE RECEIVER
SYMBOL
ZID
PARAMETER
Differential input impedance
TEST CONDITION
Drivers disabled
LIMITS
MIN
TYP
10
14
MAX
UNIT
kΩ
4
20
pF
kΩ
ZIC
C
Common mode input impedance
Drivers disabled
24
pF
VTH-R
Receiver input threshold voltage
Drivers disabled
–30
30
mV
VTH-CB
Cable bias detect threshold, TPBn cable inputs
Drivers disabled
0.6
1.0
V
VTH+
Positive arbitration comparator threshold voltage
Drivers disabled
89
168
mV
VTH–
Negative arbitration comparator threshold voltage
Drivers disabled
–168
–89
mV
VTH–SP200
Speed signal threshold
TPBIAS–TPA common mode
voltage, drivers disabled
49
131
mV
VTH–SP400
Speed signal threshold
TPBIAS–TPA common mode
voltage, drivers disabled
314
396
mV
Connect detect output at TPBIAS pins
Drivers disabled
76
µA
ICD
1999 Jul 09
9
Philips Semiconductors
Objective specification
3-port physical layer interface
PDI1394P22
12.0 OTHER DEVICE I/O
SYMBOL
PARAMETER
TEST CONDITION
Peak
IDD
Supply current
MIN
TYP
1
MAX
UNIT
tbf
mA
Transmit 2
tbf
mA
Repeat 3
tbf
mA
4
tbf
mA
Idle
IDD–PD
Supply current in power down or
suspend mode
PD = VDD in power down mode
VTH
Cable power status threshold voltage
370 kΩ–400 kΩ resistor between cable
power and CPS pin: Measured at cable
power side of resistor
7.5
VDD >= 2.7 V, IOH = –4 mA, /ISO = VDD
2.2
V
VOH
High-level
Hi
hl
l output
t t voltage.
lt
pins
i CTL
CTLn,
Dn, SYSCLK, CNA, C/LKON
VDD >= 3.0 V, IOH = –4 mA, /ISO = VDD
2.8
V
VDD–0.4
V
Annex J: IOH = –9 mA, /ISO = 0
tbf
tbf
mA
8.0
8.5
V
IOL = 4 mA, /ISO = VDD
0.4
Annex J: IOL = 9 mA, /ISO = 0
0.4
V
0.08
0.25
mA
–0.25
–0.08
mA
5
µA
5
µA
–40
–20
µA
–90
–45
–22
µA
86
260
450
µA
VDD/2 + 0.3
VDD/2 + 0.9
V
VDD/2 – 0.9
VDD/2 – 0.3
V
VLREF+1
V
VOL
O
Low level output voltage
Low-level
IBH+
Positive peak bus holder current
IBH–
Negative peak bus holder current
/ISO = VDD, VI = 0 V to VDD
/ISO = VDD, VI = 0 V to VDD
II
Input current, pins LREQ, LPS, PD,
TEST0, TEST1, PC0–PC2
/ISO = 0 V; VDD = 3.6 V
IOZ
Off-state current, pins CTLn, Dn,
C/LKON
VO = VDD or 0 V
–5
IRST-UP
S
current /RESET input
Pullup current,
VI = 1.5 V, PD = 0
–80
VI = 0 V, PD = 0
IRST-DN
Pulldown current, /RESET input
VI = VDD, PD = VDD
VIT+
Positive going threshold voltage, LREQ,
CTL0, CTL1, D0–D7, C/LKON inputs 5
/ISO = 0 V
VIT–
Negative going threshold voltage, LREQ,
/ISO = 0 V
CTL0, CTL1, D0–D7, C/LKON inputs 5
VIT+
Positive going threshold voltage, PD,
LPS inputs
/ISO = 0 V. VLREF = 0.42 x VDD
VIT–
Negative going threshold voltage, PD,
LPS inputs
/ISO = 0 V. VLREF = 0.42 x VDD
VO
TPBIAS output voltage
At rated IO current
VLREF+0.2
1.665
V
V
2.015
V
NOTES:
1. Worst case, all ports transmitting, 100% bandwidth at S400, VDD = 3.6 V, TA = 0°C: At TA = 70°C, the maximum current is tbf mA.
2. All ports transmitting, 100% bandwidth at S400, VDD = 3.3 V, TA = 25°C
3. Receiving on port 0 and transmitting on port 1 and port 2. Full ISO payload of 84 µS, S400, data value of CCCCCCCCh, VDD = 3.3 V, TA = 25°C
4. Receiving cycle starts on port 0 and transmitting cycle starts on port 1 and port 2, VDD = 3.3 V, TA = 25°C
5. C/LKON is only an input when /RESET = 0
1999 Jul 09
10
Philips Semiconductors
Objective specification
3-port physical layer interface
PDI1394P22
13.0 THERMAL CHARACTERISTICS
SYMBOL
RΘjA
PARAMETER
TEST CONDITION
Junction-to-free-air thermal resistance
LIMITS
MIN
TYP
Board mounted, no air flow
MAX
UNIT
°C/W
TBD
14.0 AC CHARACTERISTICS
SYMBOL
PARAMETER
CONDITION
Transmit jitter
TPA, TPB
MIN
TYP
MAX
UNIT
0.15
ns
Transmit skew
Between TPA and TPB
0.10
ns
tr
TPA, TPB differential output voltage rise time
10% to 90%; At 1394 connector
0.5
1.2
ns
tf
0.5
1.2
ns
TPA, TPB differential output voltage fall time
90% to 10%; At 1394 connector
tSU
Setup time, CTL0, CTL1, D1–D7, LREQ to SYSCLK
50% to 50%; See Figure 2
5
ns
tH
Hold time, CTL0, CTL1, D1–D7, LREQ after SYSCLK
50% to 50%; See Figure 2
0
ns
tD
Delay time SYSCLK to CTL0, CTL1, D1–D7
50% to 50%; See Figure 3
0.5
11
ns
15.0 TIMING WAVEFORMS
TPAn+
TPBn+
SYSCLK
56 Ω
tD
TPAn–
TPBn–
Dn, CTLn, LREQ
SV01098
SV01100
Figure 1. Test load diagram
Figure 3. Dn, CTLn, output delay relative to SYSCLK
SYSCLK
tSU
tH
Dn, CTLn, LREQ
SV01099
Figure 2. Dn, CTLn, LREQ input setup and hold times
1999 Jul 09
11
Philips Semiconductors
Objective specification
3-port physical layer interface
PDI1394P22
16.0 INTERNAL REGISTER CONFIGURATION
The configuration of the base registers is shown in Table 1, and
corresponding field descriptions are given in Table 2. The base
register field definitions are unaffected by the selected page number.
There are 16 accessible internal registers in the PDI1394P22. The
configuration of the registers at addresses 0 through 7 (the base
registers) is fixed, while the configuration of the registers at
addresses 8h through Fh (the paged registers) is dependent upon
which one of eight pages, numbered 0h through 7h, is currently
selected. The selected page is set in base register 7h.
A reserved register or register field (marked as Reserved or Rsvd in
the following register configuration tables) is read as 0, but is subject
to future usage. All registers in address pages 2 through 6 are
reserved.
Table 1. Base Register Configuration
BIT POSITION
ADDRESS
0
1
RHB
IBR
2
0000
0001
3
4
5
Physical ID
6
7
R
CPS
Gap_Count
0010
Extended (111b)
Rsvd
Num_Ports (0011b)
0011
PHY_Speed (010b)
Rsvd
Delay (0000b)
Jitter (000)
0100
L
C
0101
RPIE
ISBR
CTOI
Pwr_Class
CPSI
0110
STOI
PEI
EAA
EMC
Reserved
0111
Page_Select
Rsvd
Port Select
Table 2. Base Register Field Descriptions
SIZE
TYPE
Physical ID
FIELD
6
Rd
This field contains the physical address ID of this node determined during self–ID. The physical-ID is
invalid after a bus reset until self-ID has completed as indicated by an unsolicited register-0 status
transfer.
R
1
Rd
Root. This bit indicates that this node is the root node. The R bit is reset to 0 by bus reset, and is set to
1 during tree-ID if this node becomes root.
CPS
1
Rd
Cable-power-status. This bit indicates the state of the CPS input terminal. The CPS terminal is normally
tied to serial bus cable power through a 370 kΩ–410 kΩ resistor. A 0 in this bit indicates that the cable
power voltage has dropped below its threshold for ensured reliable operation.
RHB
1
Rd/Wr
Root-holdoff bit. This bit instructs the PHY to attempt to become root after the next bus reset. The RHB
bit is reset to 0 by a hardware reset, and is unaffected by a bus reset.
IBR
1
Gap_Count
6
Rd/Wr
Extended
3
Rd
Extended register definition. For the PDI1394P22, this field is 111b, indicating that the extended register
set is implemented.
Num_Ports
4
Rd
Number of ports. This field indicates the number of ports implemented in the PHY. For the PDI1394P22
this field is 3.
PHY_Speed
3
Rd
PHY speed capability. For the PDI1394P22, this field is 010b, indicating S400 speed capability.
Delay
4
Rd
PHY repeater data delay. This field indicates the worst case repeater data delay for this PHY,
expressed as 144+(delay × 20) ns. For the PDI1393P21, this field is 0.
L
1
Rd/Wr
Link active status. This bit indicates that this node’s link is active. The logical AND of this bit and the
LPS active status is replicated in the L field (bit 9) of the self-ID packet. This bit is set to 1 by a
hardware reset and is unaffected by a bus reset.
C
1
Rd/Wr
Contender status. This bit indicates that this node is a contender for the bus or isochronous resource
manager. This bit is replicated in the “c” field (bit 20) of the self-ID packet. This bit is set to the state
specified by the C/LKON input terminal by a hardware reset and is unaffected by a bus reset.
Jitter
3
1999 Jul 09
Rd/Wr
Rd
DESCRIPTION
Initiate bus reset. This bit instructs the PHY to initiate a long (166 µs) bus reset at the next opportunity.
Any receive or transmit operation in progress when this bit is set will complete before the bus reset is
initiated. The IBR bit is reset to 0 after a hardware reset or a bus reset.
Arbitration gap count. This value is used to set the subaction (fair) gap, arb-reset gap, and arb-delay
times. The gap count can be set either by a write to the register, or by reception or transmission of a
PHY_CONFIG packet. The gap count is reset to 3Fh by hardware reset or after two consecutive bus
resets without an intervening write to the gap count register (either by a write to the PHY register or by
a PHY_CONFIG packet).
PHY repeater jitter. This field indicates the worst case difference between the fastest and slowest
repeater data delay, expressed as (Jitter + 1) × 20 ns. For the PDI1394P22, this field is 0.
12
Philips Semiconductors
Objective specification
3-port physical layer interface
FIELD
PDI1394P22
SIZE
TYPE
DESCRIPTION
Pwr_Class
3
Rd/Wr
Node power class. This field indicates this node’s power consumption and source characteristics and is
replicated in the pwr field (bits 21–23) of the self-ID packet. This field is reset to the state specified by
the PC0–PC2 input terminals upon hardware reset, and is unaffected by a bus reset. See Table 18.
RPIE
1
ISBR
1
Rd/Wr
Rd/Wr
Resuming port interrupt enable. This bit, if set to 1, enables the port event interrupt (PEI) bit to be set
whenever resume operations begin on any port. This bit is reset to 0 by hardware reset and is
unaffected by bus reset.
Initiate short arbitrated bus reset. This bit, if set to 1, instructs the PHY to initiate a short (1.3 µs)
arbitrated bus reset at the next opportunity. This bit is reset to 0 by a bus reset.
NOTE: Legacy IEEE Std 1394–1995 compliant PHYs are not capable of performing short bus resets.
Therefore, initiation of a short bus reset in a network that contains such a legacy device results in a long
bus reset being performed.
CTOI
1
Rd/Wr
Configuration time-out interrupt. This bit is set to 1 when the arbitration controller times-out during
tree-ID start, and may indicate that the bus is configured in a loop. This bit is reset to 0 by hardware
reset, or by writing a 1 to this register bit.
NOTE: If the network is configured in a loop, only those nodes which are part of the loop should
generate a configuration time out interrupt. All other nodes should instead time out waiting for the
tree-ID and/or self-ID process to complete and then generate a state time-out interrupt and bus-reset.
CPSI
1
Rd/Wr
Cable-power-status interrupt. This bit is set to 1 whenever the CPS input transitions from high to low
indicating that cable power may be too low for reliable operation. This bit is reset to 0 by hardware
reset, or by writing a 1 to this register bit.
STOI
1
Rd/Wr
State time-out interrupt. This bit indicates that a state time-out has occurred. This bit is reset to 0 by
hardware reset, or by writing a 1 to this register bit.
PEI
1
Rd/Wr
Port event interrupt. This bit is set to 1 on any change in the connected, bias, disabled, or fault bits for
any port for which the port interrupt enable (PIE) bit is set. Additionally, if the resuming port interrupt
enable (RPIE) bit is set, the PEI bit is set to 1 at the start of resume operations on any port. This bit is
reset to 0 by hardware reset, or by writing a 1 to this register bit.
EAA
1
Rd/Wr
Enable arbitration acceleration. This bit enables the PHY to perform the various arbitration acceleration
enhancements defined in P1394a (ACK-accelerated arbitration, asynchronous fly-by concatenation,
and isochronous fly-by concatenation). This bit is reset to 0 by hardware reset and is unaffected by bus
reset.
NOTE: The EAA bit should be set only if the attached LLC is P1394a compliant. If the LLC is not
P1394a compliant, use of the arbitration acceleration enhancements can interfere with isochronous
traffic by excessively delaying the transmission of cycle-start packets.
EMC
1
Rd/Wr
Enable multispeed concatenated packets. This bit enables the PHY to transmit concatenated packets of
differing speeds in accordance with the protocols defined in P1394a. This bit is reset to 0 by hardware
reset and is unaffected by bus reset.
NOTE: The use of multispeed concatenation is completely compatible with networks containing legacy
IEEE Std 1394–1995 PHYs. However, use of multispeed concatenation requires that the attached LLC
be P1394a compliant.
Page_Select
3
Rd/Wr
Page_Select. This field selects the register page to use when accessing register addresses 8 through
15. This field is reset to 0 by a hardware reset and is unaffected by bus-reset.
Port_Select
4
Rd/Wr
Port_Select. This field selects the port when accessing per-port status or control (e.g., when one of the
port status/control registers is accessed in page 0). Ports are numbered starting at 0. This field is reset
to 0 by hardware reset and is unaffected by bus reset.
1999 Jul 09
13
Philips Semiconductors
Objective specification
3-port physical layer interface
PDI1394P22
The Port Status page provides access to configuration and status information for each of the ports. The port is selected by writing 0 to the
Page_Select field and the desired port number to the Port_Select field in base register 7. The configuration of the port status page registers is
shown in Table 3 and corresponding field descriptions given in Table 4. If the selected port is unimplemented, all registers in the port status page
are read as 0.
Table 3. Page 0 (Port Status) Register Configuration
BIT POSITION
ADDRESS
0
1000
1
2
AStat
1001
3
BStat
Peer_Speed
PIE
4
5
6
7
Ch
Con
Bias
Dis
Fault
1010
Reserved
1011
Reserved
1100
Reserved
1101
Reserved
1110
Reserved
1111
Reserved
Reserved
Table 4. Page 0 (Port Status) Register Field Descriptions
FIELD
AStat
SIZE
TYPE
2
Rd
DESCRIPTION
TPA line state. This field indicates the TPA line state of the selected port, encoded as follows:
Code
11
01
10
00
Arb Value
Z
1
0
invalid
BStat
2
Rd
TPB line state. This field indicates the TPB line state of the selected port. This field has the same
encoding as the ASTAT field.
Ch
1
Rd
Child/parent status. A 1 indicates that the selected port is a child port. A 0 indicates that the selected
port is the parent port. A disconnected, disabled, or suspended port is reported as a child port. The Ch
bit is invalid after a bus-reset until tree-ID has completed.
Con
1
Rd
Debounced port connection status. This bit indicates that the selected port is connected. The
connection must be stable for the debounce time of 330ms–350ms for the Con bit to be set to 1. The
Con bit is reset to 0 by hardware reset and is unaffected by bus reset.
NOTE: The Con bit indicates that the port is physically connected to a peer PHY, but the port is not
necessarily active.
Bias
1
Rd
Dis
1
Rd/Wr
Peer_Speed
3
Rd
Debounced incoming cable bias status. A 1 indicates that the selected port is detecting incoming cable
bias. The incoming cable bias must be stable for the debounce time of 41.6µs–52µs for the Bias bit to
be set to 1.
Port disabled control. If 1, the selected port is disabled. The Dis bit is reset to 0 by hardware reset (all
ports are enabled for normal operation following hardware reset). The Dis bit is not affected by bus
reset.
Port peer speed. This field indicates the highest speed capability of the peer PHY connected to the
selected port, encoded as follows:
Code
000
001
010
011–111
Peer Speed
S100
S200
S400
invalid
The Peer_Speed field is invalid after a bus reset until self-ID has completed.
NOTE: Peer speed codes higher than 010b (S400) are defined in P1394a. However, the PDI1394P22
is only capable of detecting peer speeds up to S400.
PIE
1
Rd/Wr
Port event interrupt enable. When set to 1, a port event on the selected port will set the port event
interrupt (PEI) bit and notify the link. this bit is reset to 0 by a hardware reset, and is unaffected by
bus-reset.
Fault
1
Rd/Wr
Fault. This bit indicates that a resume-fault or suspend-fault has occurred on the selected port, and that
the port is in the suspended state. A resume-fault occurs when a resuming port fails to detect incoming
cable bias from its attached peer. A suspend-fault occurs when a suspending port continues to detect
incoming cable bias from its attached peer. Writing 1 to this bit clears the fault bit to 0. This bit is reset to
0 by hardware reset and is unaffected by bus reset.
1999 Jul 09
14
Philips Semiconductors
Objective specification
3-port physical layer interface
PDI1394P22
The Vendor Identification page is used to identify the vendor/manufacturer and compliance level. The page is selected by writing 1 to the
Page_Select field in base register 7. The configuration of the Vendor Identification page is shown in Table 5, and corresponding field
descriptions are given in Table 6.
Table 5. Page 1 (Vendor ID) Register Configuration
BIT POSITION
ADDRESS
0
1
2
3
4
1000
Compliance
1001
Reserved
1010
Vendor_ID[0]
1011
Vendor_ID[1]
1100
Vendor_ID[2]
1101
Product_ID[0]
1110
Product_ID[1]
1111
Product_ID[2]
5
6
7
Table 6. Page 1 (Vendor ID) Register Field Descriptions
SIZE
TYPE
Compliance
FIELD
8
Rd
Compliance level. For the PDI1394P22, this field is 01h, indicating compliance with the P1394a
specification.
Vendor_ID
24
Rd
Manufacturer’s organizationally unique identifier (OUI). For the PDI1394P22, this field is 00_06_37h
(Philips Semiconductors) (the MSB is at register address 1010b).
Product_ID
24
Rd
Product identifier. For the PDI1394P22, this field is 43_11_00h (the MSB is at register address 1101b).
1999 Jul 09
DESCRIPTION
15
Philips Semiconductors
Objective specification
3-port physical layer interface
PDI1394P22
17.0 APPLICATION INFORMATION
400K
CPS
PDI1394P21
CABLE
POWER
PAIR
0.3–1.0 µF
TPBIAS
56Ω
56Ω
TPAn+
CABLE
PAIR A
TPAn–
CABLE PORT
TPBn+
CABLE
PAIR B
TPBn–
56Ω
220pF
56Ω
OUTER SHIELD
TERMINATION
5 kΩ
SV01744
The IEEE Std 1394–1995 calls for a 250 pF capacitor, which is a non-standard component value. A 220 pF capacitor is recommended.
Figure 4. Twisted pair cable interface connections
OUTER CABLE SHIELD
0.01 µF
1 MΩ
0.001 µF
CHASSIS GROUND
SV01748
Figure 5. Typical outer shield termination
1 kΩ
3
LINK POWER
LPS
SQUARE WAVE INPUT
LPS
DGND
0.001 µF
0.1 µF
6
DVDD
1 kΩ
VDD
SV01781
Use one of these networks per side for all digital power and ground
pins and one per side for all analog power and ground pins. Place
the network as close to the PHY as possible.
Figure 6. Power supply decoupling network
1999 Jul 09
SV01750
Figure 7. Non-isolated connection variations for LPS
16
Philips Semiconductors
Objective specification
3-port physical layer interface
PDI1394P22
17.1 External Component Connections
VDD
12 pF
12 pF
24.576 MHz
6.34 kΩ
±1%
0.1 µF
0.001 µF
61
60
59
58
57
56
55
54
53
52
51
50
49
XO
XI
PLLGND
PLLVDD
DGND
R1
R0
AGND
AGND
AVDD
AVDD
AGND
DGND
62
DVDD
63
/RESET
64
SYSCLK
0.1 µF
0.3–1.0 µF
1
LREQ
TPBIAS2
48
2
DGND
TPA2+
47
3
CTL0
TPA2–
46
4
CTL1
TPB2+
45
5
D0
TPB2–
44
6
D1
AVDD
43
7
DVDD
TPBIAS1
42
8
D2
TPA1+
41
9
D3
TPA1–
40
10
D4
TPB1+ 39
11
D5
TPB1–
38
12
D6
TPBIAS0
37
13
D7
TPA0+
36
14
DGND
TPA0–
35
CNA OUT
15
CNA
TPB0+ 34
LINK PULSE
OR VDD
16
LPS
TPB0– 33
PDI1394P22
TPBIAS
TP CABLES
INTERFACE
CONNECTION
0.3–1.0 µF
TPBIAS
TP CABLES
INTERFACE
CONNECTION
PC1
PC2
/ISO
CPS
DGND
DVDD
DVDD
TEST1
TEST0
AVDD
AVDD
AGND
19
20
21
22
23
24
25
26
27
28
29
30
31
32
TP CABLES
INTERFACE
CONNECTION
370–
410 kΩ
CABLE POWER
BUS MANAGER
LKON
10 kΩ
TPBIAS
/ISO
PC0
18
POWER CLASS
PROGRAMMING
PD
17
POWER DOWN
C/LKON
REFER TO
FIGURE 7
DVDD
0.3–1.0 µF
SV001783
See Figure 6 for recommended power and ground connections.
Figure 8. External Component Connections
1999 Jul 09
17
Philips Semiconductors
Objective specification
3-port physical layer interface
PDI1394P22
17.2 Using the PDI1394P22 with a non-P1394a
link layer
17.3 /Reset and Power Down
Forcing the /RESET pin low causes a Bus Reset condition on the
active cable ports, and resets the internal logic to the Reset Start
state. SYSCLK remains active. For power-up (and after Power
Down is asserted) /RESET must be asserted low for a minimum of
2 ms from the time that the PHY power reaches the minimum
required supply voltage. This is required to assure proper PLL
operation before the PHY begins using the clock. An internal pull-up
resistor is connected to VDD, so only an external delay capacitor is
required. When using a passive capacitor on the /RESET terminal to
generate a power-on reset signal, the minimum value of 0.1 µF and
also satisfies the following equation:
The PDI1394P22 implements the PHY-LLC interface specified in the
P1394a Supplement. This interface is based upon the interface
described in informative Annex J of IEEE Std 1394-1995, which is the
interface used in older PHY devices. The PHY-LLC interface specified
in P1394a is completely compatible with the older Annex J interface.
The P1394a Supplement includes enhancements to the Annex J
interface that must be comprehended when using the PDI1394P22
with a non-P1394a LLC device.
• A new LLC service request was added which allows the LLC to
temporarily enable and disable asynchronous arbitration
accelerations. If the LLC does not implement this new service
request, the arbitration enhancements should not be enabled (see
the EAA bit in PHY register 5).
Cmin = 0.0077 × T + 0.085
where Cmin is the minimum capacitance on the /RESET terminal in
µF, and T is the VDD ramp time, 10%–90%, in ms.
• The capability to perform multispeed concatenation (the
Additionally, an approximately 120 kΩ resistor should be connected
in parallel with the reset capacitor from the /RESET terminal to GND
to ensure that the capacitor is discharged when PHY power is
removed. An alternative to the passive reset is to actively drive
/RESET low for the minimum reset time following power on. This
input is a standard logic buffer and may also be driven by an open
drain logic output buffer.
concatenation of packets of differing speeds) was added in order
to improve bus efficiency (primarily during isochronous
transmission). If the LLC does not support multispeed
concatenation, multispeed concatenation should not be enabled in
the PHY (see the EMC bit in PHY register 5).
• In order to accommodate the higher transmission speeds expected
The /RESET pin also has a n-channel pull-down transistor activated
by the Power Down pin. For a reset during normal operation, a 10 us
low pulse on this pin will accomplish a full PHY reset. This pulse, as
well as the 2 ms power up pulse, could be microprocessor
controlled, in which case the external delay capacitor would not be
needed. For more details on using single capacitor isolation with this
pin, please refer to the Philips Isolation Application Note AN2452
in future revisions of the standard, P1394a extended the speed
code in bus requests from 2 bits to 3 bits, increasing the length of
the bus request from 7 bits to 8 bits. The new speed codes were
carefully selected so that new P1394a PHY and LLC devices would
be compatible, for speeds from S100 to S400, with legacy PHY and
LLC devices that use the 2-bit speed codes. The PDI1394P22
correctly interprets both 7-bit bus requests (with 2-bit speed code)
and 8-bit bus requests (with 3-bit speed codes). Moreover, if a 7-bit
bus request is immediately followed by another request (e.g., a
register read or write request), the PDI1394P22 correctly interprets
both requests. Although the PDI1394P22 correctly interprets 8-bit
bus requests, a request with a speed code exceeding S400 results
in the PDI1394P22 transmitting a null packet (data-prefix followed
by data-end, with no data in the packet).
1999 Jul 09
The Power Down input powers down all device functions with the
exception of the CNA circuit to conserve power in portable or
battery-powered applications. It must be held high for at least 3.5 ms
to assure a successful reset after power down. This pin is equipped
with Bus Hold circuitry and supports an optional isolation barrier.
18
Philips Semiconductors
Objective specification
3-port physical layer interface
PDI1394P22
18.0 PRINCIPLES OF OPERATION
terminals are used for data transfer. When the PDI1394P22 is in
control of the D0–D7 bus, unused Dn terminals are driven low during
S100 and S200 operations. When the LLC is in control of the D0–D7
bus, unused Dn terminals are ignored by the PDI1394P22.
The PDI1394P22 is designed to operate with an LLC such as the
Philips Semiconductors PDI1394L11 or PDI1394L21. The following
paragraphs describe the operation of the PHY-LLC interface.
The interface to the LLC consists of the SYSCLK, CTL0–CTL1,
D0–D7, LREQ, LPS, C/LKON, and /ISO terminals on the
PDI1394P22 as shown in Figure 9.
The LREQ terminal is controlled by the LLC to send serial service
requests to the PHY in order to request access to the serial bus for
packet transmission, read or write PHY registers, or control
arbitration acceleration.
The LPS and C/LKON terminals are used for power management of
the PHY and LLC. The LPS terminal indicates the power status of
the LLC, and may be used to reset the PHY-LLC interface or to
disable SYSCLK. The C/LKON terminal is used to send a wake-up
notification to the LLC and to indicate an interrupt to the LLC when
either LPS is inactive or the PHY register L bit is zero.
PDI1394P21
SYSCLK
CTL0–CTL1
LINK LAYER
CONTROLLER
The /ISO terminal is used to enable the output differentiation logic
on the CTL0–CTL1 and D0–D7 terminals. Output differentiation is
required when an isolation barrier of the type described in Annex J
of IEEE Std 1394-1995 is implemented between the PHY and LLC.
D0–D7
LREQ
LPS
The PDI1394P22 normally controls the CTL0–CTL1 and D0–D7
bidirectional buses. The LLC is allowed to drive these buses only
after the LLC has been granted permission to do so by the PHY.
C/LKON
/ISO
/ISO
/ISO
There are four operations that may occur on the PHY-LLC interface:
link service request, status transfer, data transmit, and data receive.
The LLC issues a service request to read or write a PHY register, to
request the PHY to gain control of the serial bus in order to transmit
a packet, or to control arbitration acceleration.
SV01757
Figure 9. PHY-LLC interface
The SYSCLK terminal provides a 49.152 MHz interface clock. all
control and data signals are synchronized to, and sampled on, the
rising edge of SYSCLK.
The PHY may initiate a status transfer either autonomously or in
response to a register read request from the LLC.
The PHY initiates a receive operation whenever a packet is received
from the serial bus.
The CTL0 and CTL1 terminals form a bidirectional control bus,
which controls the flow of information and data between the
PDI1394P22 and LLC.
The PHY initiates a transmit operation after winning control of the
serial-bus following a bus request by the LLC. The transmit
operation is initiated when the PHY grants control of the interface to
the LLC.
The D0–D7 terminals form a bidirectional data bus, which is used to
transfer status information, control information, or packet data
between the devices. The PDI1394P22 supports S100, S200, and
S400 data transfers over the D0–D7 data bus. In S100 operation
only the D0 and D1 terminals are used; in S200 operation only the
D0–D3 terminals are used; and in S400 operation all D0–D7
The encoding of the CTL0–CTL1 bus is shown in Table 7 and
Table 8.
Table 7. CTL encoding when PHY has control of the bus
CTL0
CTL1
0
0
Idle
NAME
No activity (this is the default mode)
DESCRIPTION
0
1
Status
Status information is being sent from the PHY to the LLC
1
0
Receive
An incoming packet is being sent from the PHY to the LLC
1
1
Grant
The LLC has been given control of the bus to send an outgoing packet
Table 8. CTL encoding when LLC has control of the bus
CTL0
CTL1
NAME
DESCRIPTION
0
0
Idle
The LLC releases the bus (transmission has been completed)
0
1
Hold
The LLC is holding the bus while data is being prepared for transmission, or indicating
that another packet is to be transmitted (concatenated) without arbitrating
1
0
Transmit
An outgoing packet is being sent from the LLC to the PHY
1
1
Reserved
None
1999 Jul 09
19
Philips Semiconductors
Objective specification
3-port physical layer interface
LR0
LR1
LR2
PDI1394P22
LR3
LR(n–2)
LR(n–1)
SV01758
Figure 10. LREQ Request Stream
For a bus request the length of the LREQ bit stream is 7 or 8 bits, as
shown in Table 11.
18.1 LLC service request
To request access to the bus, to read or write a PHY register, or to
control arbitration acceleration, the LLC sends a serial bit stream on
the LREQ terminal as shown in Figure 10.
Table 11. Bus Request
The length of the stream will vary depending on the type of request
as shown in Table 9.
BIT(S)
0
Table 9. Request Stream Bit Length
REQUEST TYPE
7 or 8
Read register request
9
Write register request
17
Acceleration control request
6
1–3
Request Type
Indicates the type of bus request. See
Table 10.
4–6
Request Speed
Indicates the speed at which the PHY
will send the data for this request. See
Table 12 for the encoding of this field.
Stop Bit
Indicates the end of the transfer
(always 0). If bit 6 is 0, this bit may be
omitted.
7
Regardless of the type of request, a start bit of 1 is required at the
beginning of the stream, and a stop bit of 0 is required at the end of
the stream. The second through fourth bits of the request stream
indicate the type of the request. In the descriptions below, bit 0 is the
most significant, and is transmitted first in the request bit stream.
The LREQ terminal is normally low.
The 3-bit request speed field used in bus requests is shown in
Table 12.
Table 12. Bus Request Speed Encoding
Encoding for the request type is shown in Table 10.
Table 10. Request Type Encoding
NAME
DESCRIPTION
000
ImmReq
Immediate bus request. Upon
detection of idle, the PHY takes
control of the bus immediately
without arbitration
001
IsoReq
Isochronous bus request. Upon
detection of idle, the PHY arbitrates
for the bus without waiting for a
subaction gap.
010
PriReq
Priority bus request. The PHY
arbitrates for the bus after a
subaction gap, ignores the fair
protocol.
011
FairReq
Fair bus request. The PHY
arbitrates for the bus after a
subaction gap, follows the fair
protocol
100
RdReg
The PHY returns the specified
register contents through a status
transfer.
101
WrReg
Write to the specified register.
110
AccelCtl
Enable or disable asynchronous
arbitration acceleration.
111
Reserved
Reserved.
1999 Jul 09
DESCRIPTION
Indicates the beginning of the transfer
(always 1).
NUMBER OF BITS
Bus request
LR1–LR3
NAME
Start Bit
LR4–LR6
DATA RATE
000
S100
010
S200
100
S400
All others
Invalid
NOTE:
The PDI1394P22 will accept a bus request with an invalid speed
code and process the bus request normally. However, during packet
transmission for such a request, the PDI1394P22 will ignore any
data presented by the LLC and will transmit a null packet.
For a read register request, the length of the LREQ bit stream is
9 bits as shown in Table 13.
Table 13. Read Register Request
BIT(S)
0
20
NAME
DESCRIPTION
Start Bit
Indicates the beginning of the transfer
(always 1).
1–3
Request Type
A 100 indicating this is a read register
request.
4–7
Address
Identifies the address of the PHY register
to be read.
8
Stop Bit
Indicates the end of the transfer
(always 0).
Philips Semiconductors
Objective specification
3-port physical layer interface
PDI1394P22
end of the received packet and the start of the transmitted
acknowledge packet. As soon as the receive packet ends, the PHY
immediately grants control of the bus to the LLC. The LLC sends an
acknowledgment to the sender unless the header CRC of the
received packet is corrupted. In this case, the LLC does not transmit
an acknowledge, but instead cancels the transmit operation and
releases the interface immediately; the LLC must not use this grant
to send another type of packet. After the interface is released, the
LLC may proceed with another request.
For a write register request, the length of the LREQ bit stream is
17 bits as shown in Table 14.
Table 14. Write Register Request
BIT(S)
0
NAME
DESCRIPTION
Start Bit
Indicates the beginning of the transfer
(always 1).
1–3
Request Type
A 101 indicating that this is a write
register request.
4–7
Address
Identifies the address of the PHY
register to be written to.
8–15
Data
Gives the data that is to be written to the
specified register address.
Stop Bit
Indicates the end of the transfer
(always 0).
16
The LLC may request only one bus request at a time. Once the LLC
issues any request for bus access (ImmReq, IsoReq, FairReq, or
PriReq), it cannot issue another request until the PHY indicates that
the bus request was “lost” (bus arbitration lost and another packet
received), or “won” (bus arbitration won and the LLC granted
control). The PHY ignores new bus requests while a previous bus
request is pending. All bus requests are cleared upon a bus reset.
For write register requests, the PHY loads the specified data into the
addressed register as soon as the request transfer is complete. For
read register requests, the PHY returns the contents of the
addressed register to the LLC at the next opportunity through a
status transfer. If a received packet interrupts the status transfer,
then the PHY continues to attempt the transfer of the requested
register until it is successful. A write or read register request may be
made at any time, including while a bus request is pending. Once a
read register request is made, the PHY ignores further read register
requests until the register contents are successfully transferred to
the LLC. A bus reset does not clear a pending read register request.
For an acceleration control request, the length of the LREQ data
stream is 6 bits as shown in Table 15.
Table 15. Acceleration Control Request
BIT(S)
0
NAME
DESCRIPTION
Start Bit
Indicates the beginning of the transfer
(always 1).
Request Type
A 110 indicating this is an acceleration
control request.
4
Control
Asynchronous period arbitration
acceleration is enabled if 1, and
disabled if 0.
5
Stop Bit
Indicates the end of the transfer
(always 0).
1–3
The PDI1394P22 includes several arbitration acceleration
enhancements which allow the PHY to improve bus performance
and throughput by reducing the number and length of inter-packet
gaps. These enhancements include autonomous (fly-by)
isochronous packet concatenation, autonomous fair and priority
packet concatenation onto acknowledge packets, and accelerated
fair and priority request arbitration following acknowledge packets.
Then enhancements are enabled when the EAA bit in PHY
register 5 is set.
For fair or priority access, the LLC sends the bus request (FairReq or
PriReq) at least one clock after the PHY-LLC interface becomes idle. If
the CTL terminals are asserted to the receive state (10b) by the PHY,
then any pending fair or priority request is lost (cleared). Additionally,
the PHY ignores any fair or priority requests if the Receive state is
asserted while the LLC is sending the request. The LLC may then
reissue the request one clock after the next interface idle.
The arbitration acceleration enhancements may interfere with the
ability of the cycle master node to transmit the cycle start packet
under certain circumstances. The acceleration control request is
therefore provided to allow the LLC to temporarily enable or disable
the arbitration acceleration enhancements of the PDI1394P22
during the asynchronous period. The LLC typically disables the
enhancements when its internal cycle counter rolls over indicating
that a cycle start packet is imminent, and then re-enables the
enhancements when it receives a cycle start packet. The
acceleration control request may be made at any time, however, and
is immediately serviced by the PHY. Additionally, a bus reset or
isochronous bus request will cause the enhancements to be
re-enabled, if the EAA bit is set.
The cycle master node uses priority bus request (PriReq) to send a
cycle start packet. After receiving or transmitting a cycle start
message, the LLC can issue an isochronous bus request (IsoReq).
The PHY will clear an isochronous request only when the bus has
been won.
To send an acknowledge packet, the link must issue an immediate
bus request (ImmReq) during the reception of the packet addressed
to it. This is required in order to minimize the idle gap between the
1999 Jul 09
21
Philips Semiconductors
Objective specification
3-port physical layer interface
PDI1394P22
18.2 Status transfer
subsequently interrupts the status transfer. Register contents are
considered to have been successfully transmitted only when all
8 bits of the register have been sent. A status transfer is retried after
being interrupted only if any status flags remain to be sent, or if a
register transfer has not yet completed.
A status transfer is initiated by the PHY when there is status
information to be transferred to the LLC. The PHY waits until the
interface is idle before starting the transfer. The transfer is initiated
by the PHY asserting Status (01b) on the CTL terminals, along with
the first two bits of status information on the D[0:1] terminals. The
PHY maintains CTL = Status for the duration of the status transfer.
The PHY may prematurely end a status transfer by asserting
something other than Status on the CTL terminals. This occurs if a
packet is received before the status transfer completes. The PHY
continues to attempt to complete the transfer until all status
information has been successfully transmitted. There is at least one
idle cycle between consecutive status transfers.
The definition of the bits in the status transfer is shown in Table 16,
and the timing is shown in Figure 11.
The sequence of events for a status transfer is as follows:
• Status transfer initiated. the PHY indicates a status transfer by
asserting status on the CTL lines along with the status data on the
D0 and D1 lines (only 2 bits of status are transferred per cycle).
Normally (unless interrupted by a receive operation), a status
transfer will be either 2 or 8 cycles long. A 2-cycle (4 bit) transfer
occurs when only status information is to be sent. An 8-cycle
(16 bit) transfer occurs when register data is to be sent in addition
to any status information.
The PHY normally sends just the first four bits of status to the LLC.
These bits are status flags that are needed by the LLC state
machines. The PHY sends an entire 16-bit status packet to the LLC
after a read register request, or when the PHY has pertinent
information to send to the LLC or transaction layers. The only
defined condition where the PHY automatically sends a register to
the LLC is after self-ID, where the PHY sends the physical-ID
register that contains the new node address. All status transfers are
either 4 or 16 bits unless interrupted by a received packet. The
status flags are considered to have been successfully transmitted to
the LLC immediately upon being sent, even if a received packet
• Status transfer terminated. The PHY normally terminates a status
transfer by asserting idle on the CTL lines. If a bus reset is
pending, the PHY may also assert Grant on the CTL line
immediately following a complete status transfer.
Table 16. Status Bits
BIT(S)
NAME
DESCRIPTION
0
Arbitration Reset Gap
Indicates that the PHY has detected that the bus has been idle for an arbitration reset gap time (as
defined in the IEEE 1394–1995 standard). This bit is used by the LLC in the busy/retry state machine.
1
Subaction gap
Indicates that the PHY has detected that the bus has been idle for a subaction gap time (as defined in the
IEEE 1394–1995 standard). This bit is used by the LLC to detect the completion of an isochronous cycle.
2
Bus reset
Indicates that the PHY has entered the bus reset state.
3
Interrupt
Indicates that a PHY interrupt event has occurred. An interrupt event may be a configuration time-out, a
cable-power voltage falling too low, a state time-out, or a port status change.
4–7
Address
This field holds the address of the PHY register whose contents are being transferred to the LLC.
8–15
Data
This field holds the register contents.
SYSCLK
(a)
(b)
00
CTL0, CTL1
D0, D1
00
01
00
S[0:1]
01
S[14:15]
00
SV01759
Figure 11. Status Transfer Timing
1999 Jul 09
22
Philips Semiconductors
Objective specification
3-port physical layer interface
PDI1394P22
18.3 Receive
PDI1394P22 sends at least one “data-on” indication before sending
the speed code or terminating the receive operation.
Whenever the PHY detects the data-prefix state on the serial bus, it
initiates a receive operation by asserting Receive on the CTL terminals
and a logic 1 on each of the D terminals (“data-on” indication). The
PHY indicates the start of a packet by placing the speed code
(encoded as shown in Table 17) on the D terminals, followed by
packet data. The PHY holds the CTL terminals in the Receive state
until the last symbol of the packet has been transferred. The PHY
indicates the end of packet data by asserting Idle on the CTL
terminals. All received packets are transferred to the LLC. Note that
the speed code is part of the PHY-LLC protocol and is not included in
the calculation of CRC or any other data protection mechanisms.
The PDI1394P22 also transfers its own self-ID packet, transmitted
during the self-ID phase of bus initialization to the LLC. This packet
is transferred to the LLC just as any other received self-ID packet.
The sequence of events for a normal packet reception is as follows:
• Receive operation initiated. The PHY indicates a receive
operation by asserting Receive on the CTL lines. Normally, the
interface is idle when receive is asserted. However, the receive
operation may interrupt a status transfer operation that is in
progress so that the CTL lines may change from status to receive
without an intervening idle.
Table 17. Speed Code for the Receiver
• Data-on indication. The PHY may assert the data-on indication code
D0–D7
DATA RATE
0000 0000
S100
on the D lines for one or more cycles preceding the speed code.
0100 0000
S200
• Speed code. the PHY indicates the speed of the received packet
0101 0000
S400
1111 1111
“data-on” indication
by asserting a speed code on the D lines for one cycle
immediately preceding packet data. The link decodes the speed
code on the first Receive cycle for which the D lines are not the
data-on code. If the speed code is invalid, or indicates a speed
higher than that which the link is capable of handling, the link
should ignore the subsequent data.
It is possible for the PHY to receive a null packet, which consists of
the data-prefix state on the serial bus followed by the data-end state,
without any packet data. A null packet is transmitted whenever the
packet speed exceeds the capability of the receiving PHY, or
whenever the LLC immediately releases the bus without transmitting
any data. In this case, the PHY will assert Receive on the CTL
terminals with the “data-on” indication (all 1’s) on the D terminals,
followed by Idle on the CTL terminals, without any speed code or
data being transferred. In all cases, in normal operation, the
• Receive data. Following the data-on indication (if any) and the
speed code, the PHY asserts packet data on the D lines with
receive on the CTL lines for the remainder of the receive operation.
• Receive operation terminated. The PHY terminates the receive
operation by asserting the idle on the CTL lines. The PHY asserts
at least one cycle of idle following a receive operation.
SYSCLK
(a)
00
CTL0, CTL1
10
01
00
(b)
D0–D7
XX
FF (“data-on”)
(e)
(c)
(d)
SPD
d0
dn
00
SV01760
NOTE: SPD = Speed code; see Table 17; d0–dn = Packet data.
Figure 12. Normal Packet Reception Timing
1999 Jul 09
23
Philips Semiconductors
Objective specification
3-port physical layer interface
PDI1394P22
• Data-on indication. The PHY asserts the data-on indication code
The sequence of events for a null packet reception is as follows:
• Receive operation initiated. The PHY indicates a receive
on the D lines for one or more cycles.
• Receive operation terminated. The PHY terminates the receive
operation by asserting receive on the CTL lines. Normally, the
interface is idle when receive is asserted. However, the receive
operation may interrupt a status transfer operation that is in
progress so that the CTL lines may change from status to receive
without an intervening idle.
operation by asserting Idle on the CTL lines. The PHY shall assert
at least one cycle of Idle following a receive operation.
SYSCLK
(a)
00
CTL0, CTL1
01
D0–D7
XX
10
00
(b)
(c)
FF (“data-on”)
00
SV01761
Figure 13. Null Packet Reception Timing
1999 Jul 09
24
Philips Semiconductors
Objective specification
3-port physical layer interface
PDI1394P22
18.4 Transmit
CTL terminals change direction between the PHY and the LLC,
there is an extra clock period allowed so that both sides of the
interface can operate on registered versions of the interface signals.
When the LLC issues a bus request through the LREQ terminal, the
PHY arbitrates to gain control of the bus. If the PHY wins arbitration
for the serial bus, the PHY-LLC interface bus is granted to the link by
asserting the Grant state (11b) on the CTL terminals for one
SYSCLK cycle, followed by Idle for one clock cycle. The LLC then
takes control of the bus by asserting either Idle (00b), Hold (01b), or
Transmit (10b) on the CTL terminals. Unless the LLC is immediately
releasing the interface, the link may assert the Idle state for at most
one clock before it must assert either Hold or Transmit on the CTL
terminals. The Hold state is used by the LLC to retain control of the
bus while it prepares data for transmission. The LLC may assert
Hold for zero or more clock cycles (i.e., the LLC need not assert
Hold before Transmit). The PHY asserts data-prefix on the serial
bus during this time.
The sequence of events for a normal packet transmission is as
follows:
• Transmit operation initiated. The PHY asserts grant on the CTL
lines followed by Idle to hand over control of the interface to the
link so that the link may transmit a packet. The PHY releases
control of the interface (i.e., it 3-States the CTL and D outputs)
following the idle cycle.
• Optional idle cycle. The link may assert at most one idle cycle
preceding assertion of either hold or transmit. This idle cycle is
optional; the link is not required to assert Idle preceding either
hold or transmit.
When the LLC is ready to send data, the LLC asserts Transmit on
the CTL terminals as well as sending the first bits of packet data on
the D lines. The Transmit state is held on the CTL terminals until the
last bits of data have been sent. The LLC then asserts either Hold or
Idle on the CTL terminals for one clock cycle and then asserts Idle
for one additional cycle before releasing the interface bus and
putting the CTL and D terminals in a high-impedance state. The
PHY then regains control of the interface bus.
• Optional hold cycles. The link may assert hold for up to 47 cycles
preceding assertion of transmit. These hold cycle(s) are optional;
the link is not required to assert hold preceding transmit.
• Transmit data. When data is ready to be transmitted, the link
asserts transmit on the CTL lines along with the data on the D
lines.
• Transmit operation terminated. The transmit operation is
The Hold state asserted at the end of packet transmission indicates
to the PHY that the LLC requests to send another packet
(concatenated packet) without releasing the serial bus. The PHY
responds to this concatenation request by waiting the required
minimum packet separation time and then asserting Grant as
before. This function may be used to send a unified response after
sending an acknowledge, or to send consecutive isochronous
packets during a single isochronous period. Unless multi-speed
concatenation is enabled, all packets transmitted during a single bus
ownership must be of the same speed (since the speed of the
packet is set before the first packet). If multi-speed concatenation is
enabled (when the EMSC bit of PHY register 5 is set), the LLC must
specify the speed code of the next concatenated packet on the D
terminals when it asserts Hold on the CTL terminals at the end of a
packet. The encoding for this speed code is the same as the speed
code that precedes received packet data as given in Table 17.
terminated by the link asserting hold or idle on the CTL lines the
link asserts hold to indicate that the PHY is to retain control of the
serial bus in order to transmit a concatenated packet. the link
asserts idle to indicate that packet transmission is complete and
the PHY may release the serial bus. The link then asserts Idle for
one more cycle following this cycle of hold or idle before releasing
the interface and returning control the the PHY.
• Concatenated packet speed-code. If multi-speed concatenation is
enabled in the PHY, the link shall assert a speed-code on the D
lines when it asserts Hold to terminate packet transmission. This
speed-code indicates the transmission speed for the
concatenated packet that is to follow. The encoding for this
concatenated packet speed-code is the same as the encoding for
the received packet speed-code (see Table 17). the link may not
concatenate an S100 packet onto any higher speed packet.
After sending the last packet for the current bus ownership, the LLC
releases the bus by asserting Idle on the CTL terminals for two clock
cycles. The PHY begins asserting Idle on the CTL terminals one
clock after sampling Idle from the link. Note that whenever the D and
• After regaining control of the interface, the PHY shall assert at
least one cycle of idle before any subsequent status transfer,
receive operation, or transmit operation.
SYSCLK
(a)
CTL0, CTL1
(b)
(c)
(d)
(e)
(g)
00
00
11
00
00
01
10
01
00
00
00
00
(f)
D0–D7
00
00
d0, d1, ...
00
dn
SPD
Link Controls Ctl and D
PHY High-impedance Ctl and D Outputs
SV01762
NOTE: SPD = Speed code; see Table 17; d0–dn = Packet data.
Figure 14. Normal Packet Transmission Timing
1999 Jul 09
25
Philips Semiconductors
Objective specification
3-port physical layer interface
PDI1394P22
• Null transmit termination. The null transmit operation is terminated
The sequence of events for a cancelled/null packet transmission is
as follows:
by the link asserting two cycles of idle on the CTL lines and then
releasing the interface and returning control to the PHY. Note that
the link may assert Idle for a total of 3 consecutive cycles if it
asserts the optional first idle cycle but does not assert hold. It is
recommended that the link assert 3 cycles of Idle to cancel a
packet transmission if no hold cycles are asserted. This ensures
that either the link or PHY controls the interface in all cycles.
• Transmit operation initiated. PHY asserts grant on the CTL lines
followed by idle to hand over control of the interface to the link.
• Optional Idle cycle. The link may assert at most one idle cycle
preceding assertion of hold. This idle cycle is optional; the link is
not required to assert idle preceding Hold.
• Optional Hold cycles. The link may assert Hold for up to 47 cycles
• After regaining control of the interface, the PHY shall assert at
preceding assertion of idle. These hold cycle(s) are optional; the
link is not required to assert hold preceding Idle.
least one cycle of Idle before any subsequent status transfer,
receive operation, or transmit operation.
SYSCLK
(a)
CTL0, CTL1
00
D0–D7
11
(b)
00
(c)
(d)
00
01
00
(e)
00
00
00
00
Link Controls Ctl and D
PHY High-impedance Ctl and D Outputs
SV01763
Figure 15. Cancelled/Null Packet Transmission
19.0 POWER-CLASS PROGRAMMING
The PC0–PC2 terminals are programmed to set the default value of the power-class indicated in the pwr field (bits 21–23) of the transmitted
self-ID packet. Descriptions of the various power-classes are given in Table 18. The default power-class value is loaded following a hardware
reset, but is overridden by any value subsequently loaded into the Pwr_Class field in register 4.
Table 18. Power Class Descriptions
PC0–PC2
DESCRIPTION
000
Node does not need power and does not repeat power.
001
Node is self powered, and provides a minimum of 15 W to the bus.
010
Node is self powered, and provides a minimum of 30 W to the bus.
011
Node is self powered, and provides a minimum of 45 W to the bus.
100
Node may be powered from the bus and is using up to 3 W.
101
Node is powered from the bus and uses up to 3 W. No additional power is needed to enable the link.
110
Node is powered from the bus and uses up to 3 W. An additional 3 W is needed to enable the link.
111
Node is powered from the bus and uses up to 3 W. An additional 7 W is needed to enable the link.
1999 Jul 09
26
Philips Semiconductors
Objective specification
3-port physical layer interface
PDI1394P22
LQFP64: plastic low profile quad flat package; 64 leads; body 10 x 10 x 1.4 mm
1999 Jul 09
27
SOT314-2
Philips Semiconductors
Objective specification
3-port physical layer interface
PDI1394P22
LQFP64: plastic low profile quad flat package; 64 leads; body 7 x 7 x 1.4 mm
1999 Jul 09
28
SOT414-1
Philips Semiconductors
Objective specification
3-port physical layer interface
PDI1394P22
NOTES
1999 Jul 09
29
Philips Semiconductors
Objective specification
3-port physical layer interface
PDI1394P22
Data sheet status
Data sheet
status
Product
status
Definition [1]
Objective
specification
Development
This data sheet contains the design target or goal specifications for product development.
Specification may change in any manner without notice.
Preliminary
specification
Qualification
This data sheet contains preliminary data, and supplementary data will be published at a later date.
Philips Semiconductors reserves the right to make changes at any time without notice in order to
improve design and supply the best possible product.
Product
specification
Production
This data sheet contains final specifications. Philips Semiconductors reserves the right to make
changes at any time without notice in order to improve design and supply the best possible product.
[1] Please consult the most recently issued datasheet before initiating or completing a design.
Definitions
Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For
detailed information see the relevant data sheet or data handbook.
Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one
or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or
at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended
periods may affect device reliability.
Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips
Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or
modification.
Disclaimers
Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can
reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications
do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application.
Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard
cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no
responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these
products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless
otherwise specified.
 Copyright Philips Electronics North America Corporation 1999
All rights reserved. Printed in U.S.A.
Philips Semiconductors
811 East Arques Avenue
P.O. Box 3409
Sunnyvale, California 94088–3409
Telephone 800-234-7381
Date of release: 08-99
Document order number:
1999 Jul 09
30
9397-750-06383