PCF2120 Quartz oscillator Rev. 01 — 5 February 2008 Product data sheet 1. General description The PCF2120 is a CMOS quartz oscillator optimized for low power consumption. The 32 kHz output signal is gated using an enable signal. 2. Features n n n n n n Clock operating voltage: 1.5 V to 5.5 V Low backup current: typical 0.85 µA at VDD = 3.0 V and Tamb = 25 °C 32.768 kHz output for peripheral devices Two integrated oscillator capacitors Push-pull output Internal power-on reset 3. Applications n Portable instruments n Industrial products n Battery powered products 4. Quick reference data Table 1. Quick reference data Symbol Parameter VDD supply voltage IDD supply current Conditions Min Typ Max Unit 1.5 - 5.5 V VDD = 2.0 V; Tamb = 25 °C - 210 450 nA VDD = 3.0 V; Tamb = −40 °C to +85 °C - 265 650 nA VDD = 2.0 V; Tamb = 25 °C - 615 900 nA VDD = 3.0 V; Tamb = −40 °C to +85 °C - 875 1100 nA −65 - +150 °C [1] clock output disabled clock output enabled at 32 kHz Tstg [1] storage temperature For reliable oscillator start-up at power-up: VDD > VDD(min) + 0.3 V. PCF2120 NXP Semiconductors Quartz oscillator 5. Ordering information Table 2. Ordering information Type number Package Name Description PCF2120TK HVSON10 plastic thermal enhanced very thin small outline SOT650-1 package; no leads; 10 terminals; body 3 × 3 × 0.85 mm wire bond die; 7 bonding pads; 0.57 × 1.1 × 0.2 mm PCF2120U[1] [1] Version PCF2120U Packing method: sawn wafer on Film Frame Carrier (FFC). 6. Block diagram 10 PCF2120 8 CLKOE CLKOUT 3 OSCO CL(itg) 1, 4, 6 2 OSCI 7 TEST 5 9 VSS VDD n.c. 001aaf631 Pin numbers shown for HSVON10 package. Fig 1. Block diagram 7. Pinning information 7.1 Pinning PCF2120U terminal 1 index area n.c. 1 OSCI 2 OSCO 3 n.c. 4 VSS 10 CLKOE PCF2120TK 9 VDD 8 CLKOUT 7 TEST 6 5 n.c. OSCI 1 OSCO 2 VSS 3 7 CLKOE 6 VDD 5 CLKOUT 4 TEST 001aaf628 Transparent top view Fig 2. Pin configuration HVSON10 package PCF2120_1 Product data sheet 001aah559 Fig 3. Pad configuration wire bond die © NXP B.V. 2008. All rights reserved. Rev. 01 — 5 February 2008 2 of 14 PCF2120 NXP Semiconductors Quartz oscillator 7.2 Pin description Table 3. Pin description Symbol Pin Pad Description HVSON10 Wire bond die n.c. 1 - not connected OSCI 2 1 oscillator input OSCO 3 2 oscillator output n.c. 4 - not connected VSS 5 3 ground n.c. 6 - not connected TEST 7 4 test pin CLKOUT 8 5 clock output (push-pull) VDD 9 6 supply voltage CLKOE 10 7 clock output enable input 8. Functional description The 32 kHz quartz oscillator is optimized for directly connecting to a 32 kHz tuning fork quartz crystal. No additional tuning capacitors are required. Laser tuning of the quartz or quartz selection for matching is used to tune the oscillator if required. A digital 32 kHz signal is available on pin CLKOUT. The signal on pin CLKOE is used to gate and synchronize the 32 kHz CLKOUT signal. Pin CLKOUT is a CMOS push-pull output. If disabled, it goes to LOW level. OSCOinternal 32 kHz (1) CLKOE CLKOUT 001aaf633 (1) OSCO-internal 32 kHz signal: internal signal after the Schmitt trigger connected to pin OSCO. Fig 4. CLKOUT output signal PCF2120_1 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 01 — 5 February 2008 3 of 14 PCF2120 NXP Semiconductors Quartz oscillator 9. Internal circuitry PCF2120 OSCI OSCO 1 7 6 VDD 2 5 VSS CLKOE 3 4 CLKOUT TEST 001aaf634 Pin numbers shown for HSVON10 package. Fig 5. Device diode protection diagram 10. Limiting values Table 4. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol Parameter VDD Min Max Unit supply voltage −0.5 +6.5 V IDD supply current −50 +50 mA VI input voltage −0.5 +6.5 V VO output voltage −0.5 +6.5 V II input current at any input −10 +10 mA IO output current at any output −10 +10 mA Ptot total power dissipation - 300 mW Tstg storage temperature −65 +150 °C Vesd electrostatic discharge voltage Ilu Conditions HBM [1] - ±2000 V MM [2] - ±200 V CDM [3] - ±2000 V [4] - 100 mA latch-up current [1] Human Body Model (HBM) according to JESD22-A114. [2] Machine Model (MM) according to JESD22-A115. [3] Charged-Device Model (CDM) according to JESD22-C101. [4] Latch-up testing according to JESD78. PCF2120_1 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 01 — 5 February 2008 4 of 14 PCF2120 NXP Semiconductors Quartz oscillator 11. Static characteristics Table 5. Static characteristics VDD = 1.5 V to 5.5 V; VSS = 0 V; Tamb = −40 °C to +85 °C; fosc = 32.768 kHz; quartz Rs = 40 kΩ; CL = 8 pF; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit 1.5 - 5.5 V VDD = 5.0 V - 300 550 nA VDD = 3.0 V - 235 500 nA VDD = 2.0 V - 210 450 nA VDD = 5.0 V - 345 750 nA VDD = 3.0 V - 265 650 nA - 230 600 nA VDD = 5.0 V - 1310 1700 nA VDD = 3.0 V - 845 1100 nA VDD = 2.0 V - 615 900 nA VDD = 5.0 V - 1385 1700 nA VDD = 3.0 V - 875 1100 nA VDD = 2.0 V - 635 900 nA −0.5 - VDD + 0.5 V Supply VDD supply voltage IDD supply current [1] clock output disabled Tamb = 25 °C Tamb = −40 °C to +85 °C VDD = 2.0 V clock output enabled at 32 kHz [2] Tamb = 25 °C Tamb = −40 °C to +85 °C Inputs Pin OSCI input voltage VI Pin CLKOE VI input voltage −0.5 - VDD + 0.5 V VIL LOW-level input voltage - - 0.3VDD V VIH HIGH-level input voltage 0.7VDD - - V ILI input leakage current −1 0 +1 µA −0.5 - VDD + 0.5 V VI = VDD or VSS Outputs Pin OSCO VO Pin CLKOUT VO output voltage −0.5 - VDD + 0.5 V IOL LOW-level output current VOL = 0.4 V; VDD = 5 V −1 - - mA IOH HIGH-level output current VOH = 4.6 V; VDD = 5 V - - 1 mA ILO output leakage current VO = VDD or VSS −1 0 +1 µA [1] For reliable oscillator start-up at power-up: VDD > VDD(min) + 0.3 V. PCF2120_1 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 01 — 5 February 2008 5 of 14 PCF2120 NXP Semiconductors Quartz oscillator [2] Pin CLKOUT is loaded with a 7.5 pF capacitor. When pin CLKOUT is enabled the current consumption is a function of the load on that pin, the output frequency and the supply voltage. The additional current consumption for a given load can be calculated from the formula IDD = CCLKOUT × VDD × fCLKOUT Where: IDD = supply current CCLKOUT = capacitance on pin CLKOUT VDD = supply voltage fCLKOUT = output frequency on pin CLKOUT 12. Dynamic characteristics Table 6. Dynamic characteristics VDD = 1.5 V to 5.5 V; VSS = 0 V; Tamb = −40 °C to +85 °C; fosc = 32.768 kHz; quartz Rs = 40 kΩ and CL = 8 pF; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit 6 8 10 pF - 0.2 - ppm Oscillator [1] CL(itg) integrated load capacitance ∆fosc/fosc relative oscillator frequency variation [1] ∆VDD = 200 mV; Tamb = 25 °C CL(itg) is the combined equivalent integrated oscillator input and output capacitances. 001aaf635 1.0 IDD (µA) 001aaf636 2.0 IDD (µA) 0.8 1.6 0.6 1.2 0.4 0.8 0.2 0.4 0 0 0 2 4 6 0 2 4 VDD (V) 6 VDD (V) a. CLKOUT disabled b. CLKOUT enabled at 32 kHz Tamb = 25 °C. Tamb = 25 °C. Fig 6. Supply current as a function of supply voltage PCF2120_1 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 01 — 5 February 2008 6 of 14 PCF2120 NXP Semiconductors Quartz oscillator 001aaf637 1.00 IDD (µA) 0.95 0.90 0.85 0.80 0.75 −40 0 40 80 120 Tamb (°C) VDD = 3 V; CLKOUT enabled at 32 kHz Fig 7. Supply current as a function of ambient temperature 13. Application information You can mount the PCF2120 oscillator together with the quartz crystal as an accurate and pre-tuned quartz oscillator in one package. CLKOE PCF2120 CLKOUT OSCO CL(itg) 32 kHz OSCI TEST(1) VSS VDD 10 nF 001aaf632 (1) Do not connect pin TEST; it is chip-internally connected. Fig 8. Application diagram PCF2120_1 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 01 — 5 February 2008 7 of 14 PCF2120 NXP Semiconductors Quartz oscillator 14. Package outline HVSON10: plastic thermal enhanced very thin small outline package; no leads; 10 terminals; body 3 x 3 x 0.85 mm SOT650-1 0 1 2 mm scale X A B D A A1 E c detail X terminal 1 index area C e1 terminal 1 index area e 5 y y1 C v M C A B w M C b 1 L Eh 6 10 Dh DIMENSIONS (mm are the original dimensions) UNIT A(1) max. A1 b c D(1) Dh E(1) Eh e e1 L v w y y1 mm 1 0.05 0.00 0.30 0.18 0.2 3.1 2.9 2.55 2.15 3.1 2.9 1.75 1.45 0.5 2 0.55 0.30 0.1 0.05 0.05 0.1 Note 1. Plastic or metal protrusions of 0.075 mm maximum per side are not included. REFERENCES OUTLINE VERSION IEC JEDEC JEITA SOT650-1 --- MO-229 --- EUROPEAN PROJECTION ISSUE DATE 01-01-22 02-02-08 Fig 9. Package outline SOT650-1 (HVSON10) PCF2120_1 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 01 — 5 February 2008 8 of 14 PCF2120 NXP Semiconductors Quartz oscillator 15. Bare die outline Wire bond die; 7 bonding pads; 0.57 x 1.1 x 0.2 mm bonding pad 1 corner D 3 PCF2120U 2 A 1 P4 x 0 P3 E 0 P2 y P1 4 5 6 7 detail X X DIMENSIONS (mm are the original dimensions) UNIT A D E P1 P2 P3 P4 mm 0.212 0.188 1.1 0.57 0.07 0.06 0.07 0.06 OUTLINE VERSION P1 and P3: pad size P2 and P4: passivation opening 0 0.5 1 mm scale REFERENCES IEC JEDEC EUROPEAN PROJECTION JEITA ISSUE DATE 07-12-07 08-02-01 PCF2120U Fig 10. Bare die outline PCF2120U Table 7. Bonding pad coordinates Values x and y in µm. Pad x y 1 +313 +187 2 +93 +187 3 −236 +187 4 −259 −172 5 −137 −172 6 +127 −172 7 +380 −172 16. Soldering of SMD packages This text provides a very brief insight into a complex technology. A more in-depth account of soldering ICs can be found in Application Note AN10365 “Surface mount reflow soldering description”. PCF2120_1 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 01 — 5 February 2008 9 of 14 PCF2120 NXP Semiconductors Quartz oscillator 16.1 Introduction to soldering Soldering is one of the most common methods through which packages are attached to Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both the mechanical and the electrical connection. There is no single soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high densities that come with increased miniaturization. 16.2 Wave and reflow soldering Wave soldering is a joining technology in which the joints are made by solder coming from a standing wave of liquid solder. The wave soldering process is suitable for the following: • Through-hole components • Leaded or leadless SMDs, which are glued to the surface of the printed circuit board Not all SMDs can be wave soldered. Packages with solder balls, and some leadless packages which have solder lands underneath the body, cannot be wave soldered. Also, leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered, due to an increased probability of bridging. The reflow soldering process involves applying solder paste to a board, followed by component placement and exposure to a temperature profile. Leaded packages, packages with solder balls, and leadless packages are all reflow solderable. Key characteristics in both wave and reflow soldering are: • • • • • • Board specifications, including the board finish, solder masks and vias Package footprints, including solder thieves and orientation The moisture sensitivity level of the packages Package placement Inspection and repair Lead-free soldering versus SnPb soldering 16.3 Wave soldering Key characteristics in wave soldering are: • Process issues, such as application of adhesive and flux, clinching of leads, board transport, the solder wave parameters, and the time during which components are exposed to the wave • Solder bath specifications, including temperature and impurities 16.4 Reflow soldering Key characteristics in reflow soldering are: • Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to higher minimum peak temperatures (see Figure 11) than a SnPb process, thus reducing the process window PCF2120_1 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 01 — 5 February 2008 10 of 14 PCF2120 NXP Semiconductors Quartz oscillator • Solder paste printing issues including smearing, release, and adjusting the process window for a mix of large and small components on one board • Reflow temperature profile; this profile includes preheat, reflow (in which the board is heated to the peak temperature) and cooling down. It is imperative that the peak temperature is high enough for the solder to make reliable solder joints (a solder paste characteristic). In addition, the peak temperature must be low enough that the packages and/or boards are not damaged. The peak temperature of the package depends on package thickness and volume and is classified in accordance with Table 8 and 9 Table 8. SnPb eutectic process (from J-STD-020C) Package thickness (mm) Package reflow temperature (°C) Volume (mm3) < 350 ≥ 350 < 2.5 235 220 ≥ 2.5 220 220 Table 9. Lead-free process (from J-STD-020C) Package thickness (mm) Package reflow temperature (°C) Volume (mm3) < 350 350 to 2000 > 2000 < 1.6 260 260 260 1.6 to 2.5 260 250 245 > 2.5 250 245 245 Moisture sensitivity precautions, as indicated on the packing, must be respected at all times. Studies have shown that small packages reach higher temperatures during reflow soldering, see Figure 11. temperature maximum peak temperature = MSL limit, damage level minimum peak temperature = minimum soldering temperature peak temperature time 001aac844 MSL: Moisture Sensitivity Level Fig 11. Temperature profiles for large and small components PCF2120_1 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 01 — 5 February 2008 11 of 14 PCF2120 NXP Semiconductors Quartz oscillator For further information on temperature profiles, refer to Application Note AN10365 “Surface mount reflow soldering description”. 17. Revision history Table 10. Revision history Document ID Release date Data sheet status Change notice Supersedes PCF2120_1 20080205 Product data sheet - - PCF2120_1 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 01 — 5 February 2008 12 of 14 PCF2120 NXP Semiconductors Quartz oscillator 18. Legal information 18.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 18.2 Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. 18.3 Disclaimers General — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) may cause permanent damage to the device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the Characteristics sections of this document is not implied. Exposure to limiting values for extended periods may affect device reliability. Terms and conditions of sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explicitly otherwise agreed to in writing by NXP Semiconductors. In case of any inconsistency or conflict between information in this document and such terms and conditions, the latter will prevail. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Quick reference data — The Quick reference data is an extract of the product data given in the Limiting values and Characteristics sections of this document, and as such is not complete, exhaustive or legally binding. Bare die — All die are tested on compliance with all related technical specifications as stated in this data sheet up to the point of wafer sawing for a period of ninety (90) days from the date of delivery by NXP Semiconductors. If there are data sheet limits not guaranteed, these will be separately indicated in the data sheet. There are no post-packing tests performed on individual die or wafers. NXP Semiconductors has no control of third party procedures in the sawing, handling, packing or assembly of the die. Accordingly, NXP Semiconductors assumes no liability for device functionality or performance of the die or systems after third party sawing, handling, packing or assembly of the die. It is the responsibility of the customer to test and qualify their application in which the die is used. All die sales are conditioned upon and subject to the customer entering into a written die sale agreement with NXP Semiconductors through its legal department. 18.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 19. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] PCF2120_1 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 01 — 5 February 2008 13 of 14 PCF2120 NXP Semiconductors Quartz oscillator 20. Contents 1 2 3 4 5 6 7 7.1 7.2 8 9 10 11 12 13 14 15 16 16.1 16.2 16.3 16.4 17 18 18.1 18.2 18.3 18.4 19 20 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Quick reference data . . . . . . . . . . . . . . . . . . . . . 1 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Pinning information . . . . . . . . . . . . . . . . . . . . . . 2 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3 Functional description . . . . . . . . . . . . . . . . . . . 3 Internal circuitry. . . . . . . . . . . . . . . . . . . . . . . . . 4 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 4 Static characteristics. . . . . . . . . . . . . . . . . . . . . 5 Dynamic characteristics . . . . . . . . . . . . . . . . . . 6 Application information. . . . . . . . . . . . . . . . . . . 7 Package outline . . . . . . . . . . . . . . . . . . . . . . . . . 8 Bare die outline . . . . . . . . . . . . . . . . . . . . . . . . . 9 Soldering of SMD packages . . . . . . . . . . . . . . . 9 Introduction to soldering . . . . . . . . . . . . . . . . . 10 Wave and reflow soldering . . . . . . . . . . . . . . . 10 Wave soldering . . . . . . . . . . . . . . . . . . . . . . . . 10 Reflow soldering . . . . . . . . . . . . . . . . . . . . . . . 10 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 12 Legal information. . . . . . . . . . . . . . . . . . . . . . . 13 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 13 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Contact information. . . . . . . . . . . . . . . . . . . . . 13 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. © NXP B.V. 2008. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] Date of release: 5 February 2008 Document identifier: PCF2120_1