REVISIONS LTR DESCRIPTION A Update boilerplate paragraphs to current requirements. - PHN DATE APPROVED 12-04-10 Thomas M. Hess CURRENT DESIGN ACTIVITY CAGE CODE 16236 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Prepared in accordance with ASME Y14.24 Vendor item drawing REV PAGE REV PAGE REV STATUS OF PAGES REV A A A A A A A A A A PAGE 1 2 3 4 5 6 7 8 9 10 PMIC N/A PREPARED BY Charles F. Saffle Original date of drawing CHECKED BY Charles F. Saffle YY-MM-DD 04-03-08 APPROVED BY Thomas M. Hess SIZE A REV AMSC N/A . CODE IDENT. NO. DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO TITLE MICROCIRCUIT, DIGITAL, LOW VOLTAGE CMOS, HEX INVERTER, MONOLITHIC SILICON DWG NO. V62/04653 16236 A PAGE 1 OF 10 5962-V055-12 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance hex inverter microcircuit, with an operating temperature range of -40C to +125C. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturer’s PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation: V62/04653 - Drawing number 01 X E Device type (See 1.2.1) Case outline (See 1.2.2) Lead finish (See 1.2.3) 1.2.1 Device type(s). Device type Generic 01 Circuit function SN74LVC04A-EP Hex inverter 1.2.2 Case outlines. The case outlines are as specified herein. Outline letter Number of pins X Y 14 14 JEDEC PUB 95 Package style MS-012 MO-153 Plastic small-outline Plastic small-outline 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacturer: Finish designator A B C D E Z DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO Material Hot solder dip Tin-lead plate Gold plate Palladium Gold flash palladium Other SIZE A CODE IDENT NO. 16236 REV A DWG NO. V62/04653 PAGE 2 1.3 Absolute maximum ratings. 1/ Supply voltage range (VCC) ......................................................................................... Input voltage range (VI) ............................................................................................... Output voltage range (VO) ........................................................................................... Input clamp current (IIK) (VI 0) .................................................................................. Output clamp current (IOK) (VO 0) ............................................................................. Continuous output current (IO) ..................................................................................... Continuous current through VCC or GND ..................................................................... Package thermal impedance (JA): 4/ X package ............................................................................................................. Y package ............................................................................................................. Storage temperature range (TSTG)............................................................................... 1.4 Recommended operating conditions. 2/ 3/ 4/ 5/ 6/ 86C/W 113C/W -65C to 150C 5/ 6/ Supply voltage range (VCC): Operating .............................................................................................................. Data retention only ................................................................................................ Minimum high level input voltage (VIH) (VCC = 2.7 V to 3.6 V) ..................................... Maximum low level input voltage (VIL) (VCC = 2.7 V to 3.6 V) ...................................... Input voltage range (VI) ............................................................................................... Output voltage range (VO) ........................................................................................... Maximum high level output current (IOH): VCC = 2.7 V ............................................................................................................ VCC = 3.0 V ............................................................................................................ Maximum low level output current (IOL): VCC = 2.7 V ............................................................................................................ VCC = 3.0 V ............................................................................................................ Operating free-air temperature range (TA) .................................................................. 1/ -0.5 V to 6.5 V -0.5 V to 6.5 V 2/ -0.5 V to VCC + 0.5 V 2/ 3/ -50 mA -50 mA 50 mA 100 mA 2.0 V to 3.6 V 1.5 V minimum 2.0 V 0.8 V 0.0 V to 5.5 V 0.0 V to VCC -12 mA -24 mA 12 mA 24 mA -40C to +125C Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. The input negative-voltage and output voltage ratings may be exceeded if the input and output current ratings are observed. The value of VCC is provided in the recommended operating conditions table. The package thermal impedance is calculated in accordance with JESD 51-7. Long-term high-temperature storage and/or extended use at maximum recommended operating conditions may result in a reduction of overall device life. All unused inputs of the device must be held at VCC or GND to ensure proper device operation. DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV A DWG NO. V62/04653 PAGE 3 2. APPLICABLE DOCUMENTS JEDEC – SOLID STATE TECHNOLOGY ASSOCIATION (JEDEC) JEP95 JESD51-7 – – Registered and Standard Outlines for Semiconductor Devices High Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages (Copies of these documents are available online at http://www.jedec.org or from JEDEC – Solid State Technology Association, 3103 North 10th Street, Suite 240–S, Arlington, VA 22201.) 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legibly marked with the manufacturer’s part number as shown in 6.3 herein and as follows: A. B. C. Manufacturer’s name, CAGE code, or logo Pin 1 identifier ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturer’s part number and with items A and C (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein. 3.5 Diagrams. 3.5.1 Case outlines. The case outlines shall be as shown in 1.2.2 and figure 1. 3.5.2 Truth table. The truth table shall be as shown in figure 2. 3.5.3 Logic diagram. The logic diagram shall be as shown in figure 3. 3.5.4 Terminal connections. The terminal connections shall be as shown in figure 4. 3.5.5 Test circuit and timing waveforms. The test circuit and timing waveforms shall be as shown in figure 5. DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV A DWG NO. V62/04653 PAGE 4 TABLE I. Electrical performance characteristics. 1/ Test Symbol Conditions VCC Temperature, TA Device type Limits Min High level output voltage Low level output voltage VOH VOL Unit Max IOH = -100 A 2.7 V to 3.6 V IOH = -12 mA 2.7 V 2.2 3.0 V 2.4 IOH = -24 mA 3.0 V 2.2 IOL = 100 A 2.7 V to 3.6 V 0.2 IOL = 12 mA 2.7 V 0.4 IOL = 24 mA 3.0 V 0.55 25C, -40C to 125C All VCC – 0.2 V V Input current II VI = 5.5 V or GND 3.6 V 5 A Quiescent supply current ICC VI = VCC or GND IO = 0 A 3.6 V 10 A Quiescent supply current delta ICC One input at VCC – 0.6 V, Other inputs at VCC or GND 2.7 V to 3.6 V 500 A Input capacitance Ci VI = VCC or GND 3.3 V Power dissipation capacitance per gate Cpd f = 10 MHz Propagation delay time, A to Y tpd 1/ See figure 5. 5 TYP pF 2.5 V 7 TYP pF 3.3 V 8 TYP 2.7 V 3.0 V to 3.6 V 25C 5.5 25C, -40C to 125C 0.5 ns 4.5 Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization and/or design. DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV A DWG NO. V62/04653 PAGE 5 Case X Symbol Inches Min Max A A1 b c D --0.069 0.004 0.010 0.014 0.020 0.008 NOM 0.337 0.344 Dimensions Millimeters Symbol Min Max --1.75 0.10 0.25 0.35 0.51 0.20 NOM 8.55 8.75 E E1 e L Inches Min Max Millimeters Min Max 0.150 0.157 0.228 0.244 0.050 BSC 0.016 0.044 3.81 4.00 5.80 6.20 1.27 BSC 0.40 1.12 NOTES: 1. All linear dimensions are in inches (millimeters). 2. This case outline is subject to change without notice. 3. Body dimensions do not include mold flash or protrusion, not to exceed 0.006 inches (0.15 mm). 4. Falls within JEDEC MS-012. FIGURE 1. Case outlines. DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV A DWG NO. V62/04653 PAGE 6 Case Y Symbol A A1 b c D Millimeters Min Max Dimensions Inches Symbol Min Max --1.20 0.05 0.15 0.19 0.30 0.15 NOM 4.90 5.10 --.047 .002 .006 .007 .012 .006 NOM .193 .201 E E1 e L Millimeters Min Max Min Inches Max 4.30 4.50 6.20 6.60 0.65 BSC 0.50 0.75 .169 .177 .244 .260 .026 BSC .020 .030 NOTES: 1. All linear dimensions are in millimeters (inches). 2. This case outline is subject to change without notice. 3. Body dimensions do not include mold flash or protrusion, not to exceed 0.15 millimeters (0.006 in). 4. Fall within JEDEC MO-153. FIGURE 1. Case outlines - Continued. DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV A DWG NO. V62/04653 PAGE 7 (each inverter) Input A Output Y H L L H H = High voltage level L = Low voltage level FIGURE 2. Truth table. FIGURE 3. Logic diagram. Device type Case outline Terminal Terminal number symbol 1 1A 2 1Y 3 2A 4 2Y 5 3A 6 3Y 7 GND 01 X Terminal number 8 9 10 11 12 13 14 Terminal symbol 4Y 4A 5Y 5A 6Y 6A VCC FIGURE 4. Terminal connections. DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV A DWG NO. V62/04653 PAGE 8 NOTES: 1. CL includes probe and jig capacitance. 2. All input pulses are supplied by generators having the following characteristics: PRR 10 MHz, ZO = 50 . 3. tPLH and tPHL are the same as tpd. 4. The outputs are measured one at a time with one input transition per measurement. FIGURE 5. Test circuit and timing waveforms. DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV A DWG NO. V62/04653 PAGE 9 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as indicated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturer’s standard commercial practices for electrostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturer’s data book. The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee of present or continued availability as a source of supply for the item. Vendor item drawing administrative control number 1/ Device manufacturer CAGE code Vendor part number Top side marking V62/04653-01XE 01295 SN74LVC04AQDREP LVC04AE V62/04653-01YE 01295 SN74LVC04AQPWREP LVC04AE 1/ The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation. CAGE code 01295 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO Source of supply Texas Instruments, Inc. Semiconductor Group 8505 Forest Lane P.O. Box 660199 Dallas, TX 75243 Point of contact: U.S. Highway 75 South P.O. Box 84, M/S 853 Sherman, TX 75090-9493 SIZE A CODE IDENT NO. 16236 REV A DWG NO. V62/04653 PAGE 10