REVISIONS LTR DESCRIPTION DATE APPROVED A Update boilerplate paragraphs to current requirements. - PHN 10-04-06 Thomas M. Hess B Update boilerplate to current MIL-PRF-38535 requirements. - PHN 16-01-25 Muhammad Akbar CURRENT DESIGN ACTIVITY CAGE CODE 16236 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Prepared in accordance with ASME Y14.24 Vendor item drawing REV PAGE REV PAGE REV STATUS OF PAGES REV B B B B B B B B B B PAGE 1 2 3 4 5 6 7 8 9 10 PMIC N/A PREPARED BY Charles F. Saffle DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http://www.dscc.dla.mil Original date of drawing CHECKED BY TITLE Charles F. Saffle YY-MM-DD APPROVED BY 04-03-08 Thomas M. Hess SIZE CODE IDENT. NO. A REV AMSC N/A MICROCIRCUIT, DIGITAL, LOW VOLTAGE CMOS, QUADRUPLE 2-LINE TO 1-LINE DATA SELECTOR/MULTIPLEXER, MONOLITHIC SILICON DWG NO. V62/04659 16236 B PAGE 1 OF 10 5962-V025-16 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance quadruple 2-line to 1-line data selector/multiplexer microcircuit, with an operating temperature range of -40°C to +125°C. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturer’s PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation: V62/04659 - Drawing number 01 X E Device type (See 1.2.1) Case outline (See 1.2.2) Lead finish (See 1.2.3) 1.2.1 Device type(s). Device type Generic 01 Circuit function SN74LVC157A-EP Quadruple 2-line to 1-line data selector/multiplexer 1.2.2 Case outlines. The case outlines are as specified herein. Outline letter Number of pins X Y 16 16 JEDEC PUB 95 Package style MS-012 MO-153 Plastic small-outline Plastic small-outline 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacturer: Finish designator A B C D E Z DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO Material Hot solder dip Tin-lead plate Gold plate Palladium Gold flash palladium Other SIZE A CODE IDENT NO. 16236 REV B DWG NO. V62/04659 PAGE 2 1.3 Absolute maximum ratings. 1/ Supply voltage range (VCC) ......................................................................................... Input voltage range (VI) ............................................................................................... Output voltage range (VO) ........................................................................................... Input clamp current (IIK) (VI < 0) .................................................................................. Output clamp current (IOK) (VO < 0) ............................................................................. Continuous output current (IO)..................................................................................... Continuous current through VCC or GND ..................................................................... Package thermal impedance (θJA): 4/ X package ............................................................................................................. Y package ............................................................................................................. Storage temperature range (TSTG)............................................................................... 1.4 Recommended operating conditions. 2/ 3/ 4/ 5/ 6/ 73°C/W 108°C/W -65°C to 150°C 5/ 6/ Supply voltage range (VCC): Operating .............................................................................................................. Data retention only ................................................................................................ Minimum high level input voltage (VIH) (VCC = 2.7 V to 3.6 V) ..................................... Maximum low level input voltage (VIL) (VCC = 2.7 V to 3.6 V) ...................................... Input voltage range (VI) ............................................................................................... Output voltage range (VO) ........................................................................................... Maximum high level output current (IOH): VCC = 2.7 V ............................................................................................................ VCC = 3.0 V ............................................................................................................ Maximum low level output current (IOL): VCC = 2.7 V ............................................................................................................ VCC = 3.0 V ............................................................................................................ Maximum input transition rise or fall rate (∆t/∆v) ......................................................... Operating free-air temperature range (TA) .................................................................. 1/ -0.5 V to 6.5 V -0.5 V to 6.5 V 2/ -0.5 V to VCC + 0.5 V 2/ 3/ -50 mA -50 mA ±50 mA ±100 mA 2.0 V to 3.6 V 1.5 V minimum 2.0 V 0.8 V 0.0 V to 5.5 V 0.0 V to VCC -12 mA -24 mA 12 mA 24 mA 10 ns/V -40°C to +125°C Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. The input negative-voltage and output voltage ratings may be exceeded if the input and output current ratings are observed. The value of VCC is provided in the recommended operating conditions table. The package thermal impedance is calculated in accordance with JESD 51-7. All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Use of this product beyond the manufacturers design rules or stated parameters is done at the user’s risk. The manufacturer and/or distributor maintain no responsibility or liability for product used beyond the stated limits DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV B DWG NO. V62/04659 PAGE 3 2. APPLICABLE DOCUMENTS JEDEC – SOLID STATE TECHNOLOGY ASSOCIATION (JEDEC) JEP95 JESD51-7 - Registered and Standard Outlines for Semiconductor Devices High Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages (Copies of these documents are available online at http:/www.jedec.org or from JEDEC – Solid State Technology Association, 3103 North 10th Street, Suite 240–S, Arlington, VA 22201-2107). 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legibly marked with the manufacturer’s part number as shown in 6.3 herein and as follows: A. B. C. Manufacturer’s name, CAGE code, or logo Pin 1 identifier ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturer’s part number and with items A and C (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein. 3.5 Diagrams. 3.5.1 Case outlines. The case outlines shall be as shown in 1.2.2 and figure 1. 3.5.2 Truth table. The truth table shall be as shown in figure 2. 3.5.3 Logic diagram. The logic diagram shall be as shown in figure 3. 3.5.4 Terminal connections. The terminal connections shall be as shown in figure 4. 3.5.5 Test circuit and timing waveforms. The test circuit and timing waveforms shall be as shown in figure 5. DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV B DWG NO. V62/04659 PAGE 4 TABLE I. Electrical performance characteristics. 1/ Test Symbol Conditions VCC Temperature, TA Device type Limits Min High level output voltage Low level output voltage VOH VOL Unit Max IOH = -100 µA 2.7 V to 3.6 V IOH = -12 mA 2.7 V 2.2 3.0 V 2.4 IOH = -24 mA 3.0 V 2.2 IOL = 100 µA 2.7 V to 3.6 V 0.2 IOL = 12 mA 2.7 V 0.4 IOL = 24 mA 3.0 V 0.55 25°C, -40°C to 125°C All VCC – 0.2 V V Input current II All inputs. VI = 5.5 V or GND 3.6 V ±5 µA Quiescent supply current ICC VI = VCC or GND IO = 0 A 3.6 V 10 µA Quiescent supply current delta ∆ICC One input at VCC – 0.6 V, Other inputs at VCC or GND 2.7 V to 3.6 V 500 µA Input capacitance Ci VI = VCC or GND 3.3 V Power dissipation capacitance per gate Cpd f = 10 MHz Propagation delay time, A or B to Y tpd See figure 5. Propagation delay time, A/B to Y Propagation delay time, G to Y 1/ 5 TYP pF 2.5 V 15 TYP pF 3.3 V 16 TYP 2.7 V 3.3 V ±0.3 V 25°C 25°C, -40°C to 125°C 6.2 0.8 ns 5.4 2.7 V 8.2 3.3 V ±0.3 V 0.8 7 2.7 V 7.8 3.3 V ±0.3 V 0.8 6.5 Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization and/or design. DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV B DWG NO. V62/04659 PAGE 5 Case X Symbol Inches Min Max A A1 b c D --0.069 0.004 0.010 0.014 0.020 0.008 NOM 0.386 0.394 Dimensions Millimeters Symbol Min Max --1.75 0.10 0.25 0.35 0.51 0.20 NOM 9.80 10.00 E E1 e L Inches Min Max Millimeters Min Max 0.150 0.157 0.228 0.244 0.050 BSC 0.016 0.044 3.81 4.00 5.80 6.20 1.27 BSC 0.40 1.12 NOTES: 1. All linear dimensions are in inches (millimeters). 2. This case outline is subject to change without notice. 3. Body dimensions do not include mold flash or protrusion, not to exceed 0.006 inches (0.15 mm). 4. Falls within JEDEC MS-012. FIGURE 1. Case outlines. DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV B DWG NO. V62/04659 PAGE 6 Case Y Symbol A A1 b c D Millimeters Min Max --1.20 0.05 0.15 0.19 0.30 0.15 NOM 4.90 5.10 Dimensions Inches Symbol Min Max --0.047 0.002 0.006 0.007 0.012 0.006 NOM 0.193 0.201 E E1 e L Millimeters Min Max 4.30 4.50 6.20 6.60 0.65 BSC 0.50 0.75 Min Inches Max 0.169 0.177 0.244 0.260 0.026 BSC 0.020 0.030 NOTES: 1. All linear dimensions are in millimeters (inches). 2. This case outline is subject to change without notice. 3. Body dimensions do not include mold flash or protrusion, not to exceed 0.15 millimeters (0.006 in). 4. Fall within JEDEC MO-153. FIGURE 1. Case outlines - Continued. DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV B DWG NO. V62/04659 PAGE 7 Input � /B A X L L H H � G H L L L L A X L H X X B X X X L H Output Y L L H L H H = High voltage level L = Low voltage level X = Immaterial FIGURE 2. Truth table. FIGURE 3. Logic diagram. Terminal number 1 2 3 4 5 6 7 8 Device type 01 Case outlines: X and Y Terminal Terminal symbol number � /B 9 A 1A 10 1B 11 1Y 12 2A 13 2B 14 2Y 15 GND 16 Terminal symbol 3Y 3B 3A 4Y 4B 4A � G VCC FIGURE 4. Terminal connections. DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV B DWG NO. V62/04659 PAGE 8 NOTES: 1. CL includes probe and jig capacitance. 2. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω. 3. tPLH and tPHL are the same as tpd. 4. The outputs are measured one at a time with one input transition per measurement. FIGURE 5. Test circuit and timing waveforms. DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV B DWG NO. V62/04659 PAGE 9 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as indicated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturer’s standard commercial practices for electrostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 2. 6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturer’s data book. The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee of present or continued availability as a source of supply for the item. DLA Land and Maritime maintains an online database of all current sources of supply at http://www.landandmaritime.dla.mil/Programs/Smcr/. Vendor item drawing administrative control number 1/ Device manufacturer CAGE code Vendor part number Top side marking V62/04659-01XE 01295 SN74LVC157AQDREP C157AEP V62/04659-01YE 01295 SN74LVC157AQPWREP C157AEP 1/ The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation. CAGE code 01295 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO Source of supply Texas Instruments, Inc. Semiconductor Group 8505 Forest Lane P.O. Box 660199 Dallas, TX 75243 Point of contact: U.S. Highway 75 South P.O. Box 84, M/S 853 Sherman, TX 75090-9493 SIZE A CODE IDENT NO. 16236 REV B DWG NO. V62/04659 PAGE 10