74AHC3GU04 Inverter Rev. 01 — 5 March 2004 Product data sheet 1. General description The 74AHC3GU04 is a high-speed Si-gate CMOS device. This device provides the inverting single stage function. 2. Features ■ Symmetrical output impedance ■ High noise immunity ■ ESD protection: ◆ HBM EIA/JESD22-A114-A exceeds 2000 V ◆ MM EIA/JESD22-A115-A exceeds 200 V ◆ CDM EIA/JESD22-C101 exceeds 1000 V. ■ Low power dissipation ■ Balanced propagation delays ■ SOT505-2 and SOT765-1 package ■ Output capability ±8 mA drive ■ Specified from −40 °C to +85 °C and from −40 °C to +125 °C. 3. Quick reference data Table 1: Quick reference data GND = 0 V; Tamb = 25 °C; tr = tf ≤ 3.0 ns. Symbol Parameter Conditions tPHL, tPLH propagation delay nA to nY VCC = 5 V; CL = 15 pF CI input capacitance CPD power dissipation capacitance [1] Min Typ Max Unit - 2.5 5.5 ns - 3.0 10 pF - 4 - pF [2] [1] CPD is used to determine the dynamic power dissipation (PD in µW). PD = CPD × VCC2 × fi × N + Σ(CL × VCC2 × fo) where: fi = input frequency in MHz; fo = output frequency in MHz; CL = output load capacitance in pF; VCC = supply voltage in Volts; N = total load switching outputs; Σ(CL × VCC2 × fo) = sum of the outputs. [2] The condition is VI = GND to VCC. 74AHC3GU04 Philips Semiconductors Inverter 4. Ordering information Table 2: Ordering information Type number Package Temperature range Name Description Version 74AHC3GU04DP −40 °C to +125 °C TSSOP8 plastic thin shrink small outline package; 8 leads; body width 3 mm; lead length 0.5 mm SOT505-2 74AHC3GU04DC −40 °C to +125 °C VSSOP8 plastic shrink small outline package; 8 SOT765-1 leads; body width 2.3 mm 5. Marking Table 3: Marking Type number Marking code 74AHC3GU04DP AU04 74AHC3GU04DC AU4 6. Functional diagram 1 1A 1Y 1 1 7 3 1 5 6 1 2 7 3 2A 2Y 5 6 3A 3Y 2 mna721 mna720 Fig 1. Logic symbol. Fig 2. IEC logic symbol. VCC 100 Ω A VCC Y mna636 Fig 3. Logic diagram. 9397 750 12754 Product data sheet © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 01 — 5 March 2004 2 of 17 74AHC3GU04 Philips Semiconductors Inverter 7. Pinning information 7.1 Pinning 1A 1 3Y 2 2A 3 GND 4 U04 8 VCC 7 1Y 6 3A 5 2Y mnb120 Fig 4. Pin configuration. 7.2 Pin description Table 4: Pin description Pin Symbol Description 1 1A data input 2 3Y data output 3 2A data input 4 GND ground (0 V) 5 2Y data output 6 3A data input 7 1Y data output 8 VCC supply voltage 8. Functional description 8.1 Function table Table 5: Function table [1] Input nA Output nY L H H L [1] H = HIGH voltage level; L = LOW voltage level. 9397 750 12754 Product data sheet © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 01 — 5 March 2004 3 of 17 74AHC3GU04 Philips Semiconductors Inverter 9. Limiting values Table 6: Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V). Symbol Parameter Min Max Unit VCC VI supply voltage −0.5 +7.0 V supply voltage −0.5 +7.0 V IIK input diode current VI < −0.5 V - −20 mA IOK output diode current VO < −0.5 V or VO > VCC + 0.5 V - ±20 mA IO output source or sink VΟ > −0.5 V or VO < VCC + 0.5 V current - ±25 mA ICC, IGND VCC or GND current - ±75 mA Tstg storage temperature −65 +150 °C Ptot power dissipation - 250 mW [1] Conditions Tamb = −40 °C to +125 °C [1] The input and output voltage ratings may be exceeded if the input and output current ratings are observed. 10. Recommended operating conditions Table 7: Recommended operating operations Symbol Parameter VCC Conditions Min Typ Max Unit supply voltage 2.0 5.0 5.5 V VI input voltage 0 - 5.5 V VO output voltage 0 - VCC V Tamb operating ambient temperature see Section 11 and Section 12 −40 +25 +125 °C tr, tr input rise and fall times VCC = 3.3 V ± 0.3 V - - 100 ns/V VCC = 5 V ± 0.5 V - - 20 ns/V 9397 750 12754 Product data sheet © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 01 — 5 March 2004 4 of 17 74AHC3GU04 Philips Semiconductors Inverter 11. Static characteristics Table 8: Static characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter Conditions Min Typ Max Unit HIGH-level input voltage VCC = 2.0 V 1.7 - - V VCC = 3.0 V 2.4 - - V VCC = 5.5 V 4.4 - - V VCC = 2.0 V - - 0.3 V VCC = 3.0 V - - 0.6 V VCC = 5.5 V - - 1.1 V VCC = 2.0 V; IO = −50 µA 1.9 2.0 - V VCC = 3.0 V; IO = −50 µA 2.9 3.0 - V VCC = 4.5 V; IO = −50 µA 4.4 4.5 - V VCC = 3.0 V; IO = −4.0 mA 2.58 - - V VCC = 4.5 V; IO = −8.0 mA 3.94 - - V VCC = 2.0 V; IO = 50 µA - 0 0.1 V VCC = 3.0 V; IO = 50 µA - 0 0.1 V VCC = 4.5 V; IO = 50 µA - 0 0.1 V VCC = 3.0 V; IO = 4.0 mA - - 0.36 V VCC = 4.5 V; IO = 8.0 mA - - 0.36 V Tamb = 25 °C VIH VIL VOH VOL LOW-level input voltage HIGH-level output voltage LOW-level output voltage VI = VIH or VIL VI = VIH or VIL ILI input leakage current VI = VCC or GND; VCC = 5.5 V - - 0.1 µA ICC quiescent supply current VI = VCC or GND; IO = 0 A; VCC = 5.5 V - - 1.0 µA CI input capacitance - 3.0 10 pF VCC = 2.0 V 1.7 - - V VCC = 3.0 V 2.4 - - V VCC = 5.5 V 4.4 - - V VCC = 2.0 V - - 0.3 V VCC = 3.0 V - - 0.6 V VCC = 5.5 V - - 1.1 V IO = −50 µA; VCC = 2.0 V 1.9 - - V IO = −50 µA; VCC = 3.0 V 2.9 - - V Tamb = −40 °C to 85 °C VIH VIL VOH HIGH-level input voltage LOW-level input voltage HIGH-level output voltage VI = VIH or VIL IO = −50 µA; VCC = 4.5 V 4.4 - - V IO = −4.0 mA; VCC = 3.0 V 2.48 - - V IO = −8.0 mA; VCC = 4.5 V 3.8 - - V 9397 750 12754 Product data sheet © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 01 — 5 March 2004 5 of 17 74AHC3GU04 Philips Semiconductors Inverter Table 8: Static characteristics …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter Conditions Min Typ Max Unit VOL LOW-level output voltage VI = VIH or VIL IO = 50 µA; VCC = 2.0 V - - 0.1 V IO = 50 µA; VCC = 3.0 V - - 0.1 V IO = 50 µA; VCC = 4.5 V - - 0.1 V IO = 4.0 mA; VCC = 3.0 V - - 0.44 V IO = 8.0 mA; VCC = 4.5 V - - 0.44 V ILI input leakage current VI = VCC or GND; VCC = 5.5 V - - 1.0 µA ICC quiescent supply current VI = VCC or GND; IO = 0 A; VCC = 5.5 V - - 10 µA CI input capacitance - - 10 pF VCC = 2.0 V 1.7 - - V VCC = 3.0 V 2.4 - - V VCC = 5.5 V 4.4 - - V VCC = 2.0 V - - 0.3 V VCC = 3.0 V - - 0.6 V VCC = 5.5 V - - 1.1 V Tamb = −40 °C to +125 °C VIH VIL VOH VOL HIGH-level input voltage LOW-level input voltage HIGH-level output voltage LOW-level output voltage VI = VIH or VIL IO = −50 µA; VCC = 2.0 V 1.9 - - V IO = −50 µA; VCC = 3.0 V 2.9 - - V IO = −50 µA; VCC = 4.5 V 4.4 - - V IO = −4.0 mA; VCC = 3.0 V 2.40 - - V IO = −8.0 mA; VCC = 4.5 V 3.70 - - V IO = 50 µA; VCC = 2.0 V - - 0.1 V IO = 50 µA; VCC = 3.0 V - - 0.1 V VI = VIH or VIL IO = 50 µA; VCC = 4.5 V - - 0.1 V IO = 4.0 mA; VCC = 3.0 V - - 0.55 V IO = 8.0 mA; VCC = 4.5 V - - 0.55 V ILI input leakage current VI = VCC or GND; VCC = 5.5 V - - 2.0 µA ICC quiescent supply current VI = VCC or GND; IO = 0 A; VCC = 5.5 V - - 40 µA CI input capacitance - - 10 pF 9397 750 12754 Product data sheet © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 01 — 5 March 2004 6 of 17 74AHC3GU04 Philips Semiconductors Inverter 12. Dynamic characteristics Table 9: Dynamic characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V); tr = tf ≤ 3.0 ns. See Figure 6. Symbol Parameter Conditions propagation delay nA to nY see Figure 5 Min Typ Max Unit Tamb = 25 °C tPHL, tPLH VCC = 3.0 V to 3.6 V; CL = 15 pF [1] - 3.0 7.1 ns VCC = 3.0 V to 3.6 V; CL = 50 pF [1] - 4.3 10.6 ns VCC = 4.5 V to 5.5 V; CL = 15 pF [2] - 2.5 5.5 ns VCC = 4.5 V to 5.5 V; CL = 50 pF [2] - 3.5 7.0 ns VCC = 3.0 V to 3.6 V; CL = 15 pF 1.0 - 8.5 ns VCC = 3.0 V to 3.6 V; CL = 50 pF 1.0 - 12.0 ns VCC = 4.5 V to 5.5 V; CL = 15 pF 1.0 - 6.0 ns VCC = 4.5 V to 5.5 V; CL = 50 pF 1.0 - 8.0 ns VCC = 3.0 V to 3.6 V; CL = 15 pF 1.0 - 10.0 ns VCC = 3.0 V to 3.6 V; CL = 50 pF 1.0 - 13.5 ns VCC = 4.5 V to 5.5 V; CL = 15 pF 1.0 - 7.0 ns VCC = 4.5 V to 5.5 V; CL = 50 pF 1.0 - 9.0 ns Tamb = −40 °C to 85 °C tPHL, tPLH propagation delay nA to nY see Figure 5 Tamb = −40 °C to 125 °C tPHL, tPLH propagation delay nA to nY [1] Typical values are measured at VCC = 3.3 V. [2] Typical values are measured at VCC = 5.0 V. see Figure 5 9397 750 12754 Product data sheet © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 01 — 5 March 2004 7 of 17 74AHC3GU04 Philips Semiconductors Inverter 13. AC waveforms VI nA input VM VM GND t PHL t PLH VOH 90% VM VM nY output 10% VOL t THL t TLH mna722 VM = 50 %; VI = GND to VCC. Fig 5. Input (nA) to output (nY) propagation delays. VCC PULSE GENERATOR VI VO D.U.T. RT CL mna101 Definitions for test circuit: CL = load capacitance including jig and probe capacitance. (See Section 12 for values). RT = termination resistance should be equal to the output impedance Zo of the pulse generator. Fig 6. Load circuitry for switching times. 9397 750 12754 Product data sheet © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 01 — 5 March 2004 8 of 17 74AHC3GU04 Philips Semiconductors Inverter 13.1 Typical transfer characteristics mna397 2.0 VO (V) 1.6 mna398 1.0 VO ICC (mA) 0.8 1.2 0.6 0.8 0.4 3.0 10 VO ICC (mA) VO (V) 8 6 1.5 4 ID (drain current) 0.4 ID (drain current) 0.2 2 0 0 0 0 0.4 0.8 1.2 1.6 0 0 2.0 1 2 VI (V) Fig 7. VCC = 2.0 V; IO = 0 A. VI (V) 3 Fig 8. VCC = 3.0 V; IO = 0 A. mna399 6 50 VO (V) ICC (mA) 40 VO 30 3 20 ID (drain current) 10 0 0 0 2 4 VI (V) 6 Fig 9. VCC = 5.5 V; IO = 0 A. 9397 750 12754 Product data sheet © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 01 — 5 March 2004 9 of 17 74AHC3GU04 Philips Semiconductors Inverter 13.2 Forward transconductance Rbias = 560 kΩ VCC 0.47 µF input output VI (f = 1 kHz) 100 µF A IO GND mna050 gfs = ∆IO/∆VI; VO is constant. Fig 10. Test set-up for measuring forward transconductance. mna400 40 gfs (mA/V) 30 20 10 0 0 2 4 VCC (V) 6 At Tamb = 25 °C. Fig 11. Typical forward transconductance as a function of the supply voltage. 14. Application information Some applications are: • Linear amplifier see Figure 12 • In crystal oscillator design see Figure 13. Remark: All values given are typical unless otherwise specified. 9397 750 12754 Product data sheet © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 01 — 5 March 2004 10 of 17 74AHC3GU04 Philips Semiconductors Inverter 14.1 Linear amplifier R2 VCC 1 µF R1 U04 ZL mna052 VO(max)(p-p) = VCC − 1.5 V centered at 0.5 × VCC. A OL A u = ----------------------------------------R1 1 + ------- ( 1 + A OL ) R2 AOL = open loop amplification. Au = voltage amplification. R1 ≥ 3 kΩ; R2 ≤ 1 MΩ. ZL > 10 kΩ; AOL = 20 (typical). Typical unity gain bandwidth product is 5 MHz. Fig 12. Used as a linear amplifier. 14.2 Crystal oscillator R1 R2 U04 C1 C2 out mna053 C1 = 47 pF (typical). C2 = 22 pF (typical). R1 = 1 MΩ to 10 MΩ (typical). R2 optimum value depends on the frequency and required stability against changes in VCC or average minimum ICC (ICC is typically 2 mA at VCC = 3 V and f = 1 MHz). Fig 13. Crystal oscillator configuration. Table 10: External components for resonator (f < 1 MHz) Frequency (kHz) R1 (MΩ) R2 (kΩ) C1 (pF) C2 (pF) 10 to 15.9 22 220 56 20 16 to 24.9 22 220 56 10 25 to 54.9 22 100 56 10 55 to 129.9 22 100 47 5 130 to 199.9 22 47 47 5 200 to 349.9 22 47 47 5 350 to 600 22 47 47 5 9397 750 12754 Product data sheet © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 01 — 5 March 2004 11 of 17 74AHC3GU04 Philips Semiconductors Inverter Remark: All values given are typical and must be used as initial set-up. Table 11: Optimum value for R2 Frequency (kHz) R2 (kΩ) Optimum for 3 2.0 minimum required ICC 8.0 minimum influence due to change in VCC 1.0 minimum required ICC 4.7 minimum influence due to change in VCC 0.5 minimum required ICC 2.0 minimum influence due to change in VCC 0.5 minimum required ICC 1.0 minimum influence due to change in VCC - replace R2 by C3 with a typical value of 35 pF 6 10 14 >14 9397 750 12754 Product data sheet © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 01 — 5 March 2004 12 of 17 74AHC3GU04 Philips Semiconductors Inverter 15. Package outline TSSOP8: plastic thin shrink small outline package; 8 leads; body width 3 mm; lead length 0.5 mm D E A SOT505-2 X c HE y v M A Z 5 8 A A2 (A3) A1 pin 1 index θ Lp L 1 4 e detail X w M bp 0 2.5 5 mm scale DIMENSIONS (mm are the original dimensions) UNIT A max. A1 A2 A3 bp c D(1) E(1) e HE L Lp v w y Z(1) θ mm 1.1 0.15 0.00 0.95 0.75 0.25 0.38 0.22 0.18 0.08 3.1 2.9 3.1 2.9 0.65 4.1 3.9 0.5 0.47 0.33 0.2 0.13 0.1 0.70 0.35 8° 0° Note 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. OUTLINE VERSION REFERENCES IEC SOT505-2 JEDEC JEITA EUROPEAN PROJECTION ISSUE DATE 02-01-16 --- Fig 14. Package outline TSSOP8. 9397 750 12754 Product data sheet © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 01 — 5 March 2004 13 of 17 74AHC3GU04 Philips Semiconductors Inverter VSSOP8: plastic very thin shrink small outline package; 8 leads; body width 2.3 mm D E SOT765-1 A X c y HE v M A Z 5 8 Q A A2 A1 pin 1 index (A3) θ Lp 1 4 e L detail X w M bp 0 2.5 5 mm scale DIMENSIONS (mm are the original dimensions) UNIT A max. A1 A2 A3 bp c D(1) E(2) e HE L Lp Q v w y Z(1) θ mm 1 0.15 0.00 0.85 0.60 0.12 0.27 0.17 0.23 0.08 2.1 1.9 2.4 2.2 0.5 3.2 3.0 0.4 0.40 0.15 0.21 0.19 0.2 0.13 0.1 0.4 0.1 8° 0° Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION REFERENCES IEC SOT765-1 JEDEC JEITA EUROPEAN PROJECTION ISSUE DATE 02-06-07 MO-187 Fig 15. Package outline VSSOP8. 9397 750 12754 Product data sheet © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 01 — 5 March 2004 14 of 17 74AHC3GU04 Philips Semiconductors Inverter 16. Revision history Table 12: Revision history Document ID Release date Data sheet status Change notice Order number 74AHC3GU04_1 20040305 product data - 9397 750 12754 Product data sheet Supersedes 9397 750 12754 - © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 01 — 5 March 2004 15 of 17 74AHC3GU04 Philips Semiconductors Inverter 17. Data sheet status Level Data sheet status [1] Product status [2] [3] Definition I Objective data Development This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. II Preliminary data Qualification This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. III Product data Production This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). [1] Please consult the most recently issued data sheet before initiating or completing a design. [2] The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. [3] For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status. 18. Definitions 19. Disclaimers Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Life support — These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Right to make changes — Philips Semiconductors reserves the right to make changes in the products - including circuits, standard cells, and/or software - described or contained herein in order to improve design and/or performance. When the product is in full production (status ‘Production’), relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no licence or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. 20. Contact information For additional information, please visit http://www.semiconductors.philips.com For sales office addresses, send an email to: [email protected] 9397 750 12754 Product data sheet © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 01 — 5 March 2004 16 of 17 74AHC3GU04 Philips Semiconductors Inverter 21. Contents 1 2 3 4 5 6 7 7.1 7.2 8 8.1 9 10 11 12 13 13.1 13.2 14 14.1 14.2 15 16 17 18 19 20 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Quick reference data . . . . . . . . . . . . . . . . . . . . . 1 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Functional diagram . . . . . . . . . . . . . . . . . . . . . . 2 Pinning information . . . . . . . . . . . . . . . . . . . . . . 3 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Functional description . . . . . . . . . . . . . . . . . . . 3 Function table . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 4 Recommended operating conditions. . . . . . . . 4 Static characteristics. . . . . . . . . . . . . . . . . . . . . 5 Dynamic characteristics . . . . . . . . . . . . . . . . . . 7 AC waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Typical transfer characteristics . . . . . . . . . . . . 9 Forward transconductance. . . . . . . . . . . . . . . 10 Application information. . . . . . . . . . . . . . . . . . 10 Linear amplifier . . . . . . . . . . . . . . . . . . . . . . . . 11 Crystal oscillator . . . . . . . . . . . . . . . . . . . . . . . 11 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 13 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 15 Data sheet status . . . . . . . . . . . . . . . . . . . . . . . 16 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Contact information . . . . . . . . . . . . . . . . . . . . 16 © Koninklijke Philips Electronics N.V. 2004 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Date of release: 5 March 2004 Document order number: 9397 750 12754 Published in The Netherlands