www.ti.com/ledcookbook-pr

LED Reference
Design Cookbook
www.ti.com/led
2Q 2010
2
LED Reference Design Cookbook
➔
Table of Contents
LED
Configuration
Dimming
Options
VIN
VOUT (VDC)
IOUT (mA)
Device
Page
TRIAC Dimmable LED Lighting Reference Design
3 to 5 series
TRIAC
120 and 230 V
14 to 17 V
325
TPS92010
4
10-Watt, AC/DC LED Driver
3 to 6 series
—
120 to 290 VAC
24 typical
350
TPS92010
6
Dimmable LED Lighting Driver for Lightbulb Retrofit Apps
9 to 11 series
TRIAC
90 to 265 V
28 V
350
TPS92210
8
Low-Cost AC/DC TRIAC Dimmable Driver Replacement
for Lightbulb
7 to 9 series
TRIAC dimmer
90 to 130 VAC
24 to 32
450
TPS92001
10
110-Watt, Constant-Current, Isolated Driver with PFC
7 to 15 series
(up to 4 strings)
Analog or PWM
90 to 265 VAC
22 to 60
500
UCC28810
12
100-Watt, Constant-Current, Non-Isolated Driver with PFC
15 to 30 series
PWM
90 to 265 VAC
55 to 100
900
UCC28810
14
6 series
PWM
108 to 305 VAC
70 to 85
3000
TPS92020
UCC28810
UCC28811
16
3 to 13 series
—
180 to 265 VAC
10 to 48.5
700
UCC28810
18
LED Streetlight Driver Based on SEPIC Topology
80 series
TRIAC dimmer
150 to 264 VAC
300 max
350
UCC28810
20
25-Watt Dimmable Driver with PFC
10 series
TRIAC dimmer
85 to 305 VAC
33 to 38
700
UCC28810
24
Nonsynchronous Boost LED Driver
10 series
(1 or 2 strings)
—
9 to 18 VDC
40 max
700 or 350
TPS40211
26
4 series
—
8 to 40 VDC
13 typical
350
TPS40211
28
Article
LED Drivers
NEW!
NEW!
240-W LED Lighting System
NEW!
Constant Current Driver with PFC
Wide-Input DC Voltage Range SEPIC Driver
Article
Standard
Description
TI Devices
Page
EN50065 IEC 6100-3
OFDM and S-FSK PLC Modem Kit
TMS320C2000™
OPA564
PGA112
30
DALI
DALI Reference Design Using MSP30™ MCU
MSP430™ MCU
32
Lighting Communications and Control
NEW!
NEW!
TMS320C2000™ Power-Line-Communcations Modem
Eval Kit
Digital Addressable Lighting Interface (DALI)
LED
Configuration
Dimming
Options
VIN
VOUT (VDC)
IOUT (mA)
Device
Page
8 strings (1-10
LEDs per string)
PWM
12 to 24 VDC
12 to 40 V
8X 1A
Piccolo™
MCU
33
3 series
Analog or PWM
4.5 to 7.4 VDC
10.5 typical
350
TPS61165
34
9 to 11 series
Linear
4.5 to 42 VDC
42 max
500
TL4242
36
8 parallel
(up to 8 strings)
Pending
3.0 to 5.5 VDC
2.0 to 17.0 V
120 per
channel
TLC5917
38
Wireless-Controlled Triple LED Driver
3 parallel (tricolor)
—
4.5 to 5.5 VDC
3 typical
300 per LED
TPS62260
40
Low-Voltage Buck Boost for LED Torch
1
Dual level
1.2 to 5 VDC
5 typical
600
TPS63000
42
4 to 8 series
Analog or PWM
5 to 12 VDC
VIN to 38
2000 max
TPS61500
44
Up to 10
per channel
(up to 6 channels)
PWM
5 to 24 VDC
VIN to 38
Six 25-mA
current sinks
TPS61180
TPS61181
TPS61182
46
4 strings
(15 series each)
Digital or PWM
2 to 50
0 to 49.5
2500 max
DRV9812
48
10 series
Digital or PWM
3 to 18 VDC
26 or 38
max
700 max
TPS61160/1
50
4 parallel
(2 banks of 2)
—
2.5 to 5.5 VDC
3 typical
25 per LED
TPS7510x
52
Article
LED Drivers
NEW!
DC/DC LED Developer’s Kit
3-Watt Solar Lantern
NEW!
NEW!
High-Brightness LED Driver with Switch Control
High-Brightness LED Driver with Single-Clock Operation
Boost Driver with Integrated Power Switch
1.5-A White LED Driver for Notebooks
NEW!
NEW!
Multichannel PWM Power Driver for Power
LED Applications
Small LCD Backlight with Digital and PWM Dimming
Small LCD Backlight from LDO
LED Reference Design Cookbook
Texas Instruments 2Q 2010
LED Reference Design Cookbook
3
➔
LED
Configuration
Dimming
Options
VIN
VOUT (VDC)
IOUT (mA)
Device
Page
Medium-Size LCD Backlight
3 series
Digital or PWM
3 to 12 VDC
5 typical
820 max
TPS61165
54
Large-LCD Backlight Driver
Up to 96
(12 series, 8
strings)
Analog or PWM
4 to 24 VDC
16 to 48
320
TPS61195
56
24-Channel, 12-Bit PWM LED Driver
24 parallel
Digital or PWM
3.0 to 5.5 VDC
2.0 to 17.0 V
40 per channel
TLC5951
58
24-Channel, Constant-Current LED Driver with
Global Brightness Control
24 parallel
Digital
3.0 to 5.5 VDC
2.0 to 17.0 V
35 per channel
TLC5952
60
16-Channel LED Driver with Load-Switch Dimming Control
16 parallel
PWM or Analog
3.0 to 5.5 VDC
17 max
100 per
channel
TLC59116
62
Article
LED Drivers
NEW!
NEW!
NEW!
LED Reference Design Cookbook
Helping You Solve Your Lighting Design Challenges
The LED Reference Design Cookbook is designed to provide you
with a valuable tool to help you solve your lighting design needs. Customers seeking the latest in innovative and affordable LED
lighting solutions can benefit from TI’s broad product portfolio
of AC/DC, DC/DC, LED drivers, power management devices,
wireless and wired interface control and embedded processors.
Designers have the option of not only controlling the power
stage, but regulating LED currents as well, eliminating the need
for multiple components and reducing system cost. Systems
can be designed to accurately control voltage and current
regulation for precise light intensity and color mixing, temperature
monitoring to prevent thermal runaway, intelligent/adaptive
dimming, and fault detection (over voltage/current, blown string).
Communication with external systems is also possible via powerline communication (PLC), wireless technology or interfaces.
TI has Solutions for Your
Lighting Challenges:
• Precision channel-to-channel and
chip-to-chip accuracy to create
the best hue and luminance in
your RGB message boards and
video displays
• Small footprint, highest efficiency,
programmable LED or OLED
backlight controllers
• Blinking low-power LEDs to act as
indicators in an automotive display
or in a casino game
• Controllers to power and dim high
brightness white or RGB LEDs
for architectural luminaries and
portable lighting
• Powering arrays of HB LEDs off an
AC source for use in street lighting
and replacing high-intensity
discharge (HID) lamps
• Highly integrated ZigBee®
transceivers and SoC solutions for
wireless lighting control and home
automation
LED lighting designers are challenged with meeting their efficiency
and reliability goals faster in advanced lighting designs. TI’s
lighting portfolio is helping designers achieve their goals at a
faster rate. To see the TI solutions for general lighting, signage, backlighting
and automotive, all complimented by a comprehensive customer
support network, visit:
www.ti.com/led
Texas Instruments 2Q 2010
LED Reference Design Cookbook
4
TRIAC Dimmable LED Lighting Reference Design
➔
TPS92010
NEW!
Description
This design uses the TPS92010 8-pin,
high-efficiency off-line LED lighting
controller. This controller incorporates
many features, such as frequency
fold-back and a low-power mode, to
implement a low-cost, high-efficiency
flyback converter.
An application of this converter is
retrofitting lightbulbs with LEDs.
The converter can drive 3 to 5 highbrightness LEDs in series with a
constant current of 0.35 A.
Key Features
• AC/DC TRIAC dimmable LED reference design
• Ideal for residential lighting
• 3- to 12-W applications
• High efficiency
• TI lossless dimming circuit for a
cooler, lower-power system during
deep dimming
topologies. LED current is sensed
directly to ensure its tight regulation.
A special circuit for compatibility
with TRIAC dimmers adjusts the
output current linearly, avoiding any
stroboscopic effects or audible noise
that might otherwise occur. The
TPS92010 is designed for low-power
lighting applications that do not require
power-factor correction.
Web Links
Datasheets, user’s guides, samples:
www.ti.com/sc/device/TPS92010
Design Specifications
The flyback topology is chosen
because it allows a lower component
count and lower cost than other
Efficiency without Dimmer
Efficiency with Dimmer
Dimming Performance
LED Reference Design Cookbook
Parameter
Minimum
Typical
Maximum
100
120
130
Output voltage (VDC)
9
—
18
Output current (A)
—
0.35
—
Efficiency (%)
—
80
—
Input voltage (VAC)
Output Current Regulation
Adjusting the Output Current
Output Current
(A)
R15
(W)
R17
(W)
R1
(W)
R42
(W)
0.20
1000
150
330
1000
0.225
1200
86
390
1000
0.25
1200
220
470
1000
0.275
1000
560
680
680
0.30
1500
220
680
680
0.325
1500
330
470
1500
0.35
1000
1000
820
1000
0.40
1800
470
1000
1000
0.45
2200
390
1500
1000
0.50
2700
220
1500
1000
0.60
3300
150
1500
1500
0.70
3900
270
2200
1500
Texas Instruments 2Q 2010
N
TP2
R33
3.3M
R32
3.3M
R28
27.0
R29
4.70k
Q6
Q4
FMMT458
DIM
R40
220
R35
470k
R7
470k
D3
MB6S
SI0V1
S05K150
BC817-25
Texas Instruments 2Q 2010
R34
100k
Q5
C16
220nF
1
R10
560
R23
4.70M
R24
4.70M
1
3
4
1
C18
4.7µF
1
C14
0.1µF
C17
10nF
SS LPM
FB VSD
PCS VDD
GND GD
U4
TPS92010
C23
100nF
R21
3.30M
C3
1nF
3
2
1
1
6
C10
22nF R22
3.30M
R39
47.0k
C19
4.7µF
C2
1nF
C4
330pF
D1
MB6S
4
L1
50mH
5
6
R37
1.00M
C8
1µF
R26
1.00M
U1: B
LM358AD
7
R25
1.00M
C11
0.1µF
6
2
1
5
Q2
SPD02N80C3
1
3
4
U3
PS2801C-1
8
3
7
2
1
C22
0.1µF
R8 C20
330 1nF
1
R43
39.0k
R18
68k
R11
10.0k
C7
47pF
R19
8.20k
C21
100pF
C13
1µF
R27
2.49k
R36
270k
U2
TL431A
R17
330
R15
1.50k
R13
33.0k
C6
1µF
1
1
R117
4.70k
1
1
R42
1.50M
R14
4.70k
1
U1: A
LM358AD
R1
470k
R3
8.20k
C5
1nF
R20
0.39
C1
1µF
4
8
C12
10nF
3
2
R41
1.20M
TP3
TP4
R4
2.70k
— VLED
+ VLED
Output: 0.325A/14V to 17V
R6
12.0k
Q3
2N7002
C15
0.1µF
C9
100pF
R5
10.0k
R12
1.0k
R9 2.70k
D4
SS26
See table for resistor selection to modify output current.
R38
1.00M
5
6
7
8
R16
4.70
D2
BAW56GS08
R31
270k
R2
270k
For more reference designs, see: www.ti.com/powerreferencedesigns
R30
22.0k
BC817-25
Input: 100 to 130 VAC
5
TPS92010
➔
TP1
L
TRIAC Dimmable LED Lighting Reference Design
LED Reference Design Cookbook
6
10-Watt, AC/DC LED Driver
➔
TPS92010 PMP3522
Description
The PMP3522 is a reference design
that utilizes the TPS92010 high
efficiency LED lighting driver controller.
Residential downlighting has seen
a great deal of transition to more
efficient sources of light. Compact
CFLs have become a mainstay in
residential lighting, but as the lifetime
cost of LED lamps falls, all the more
low-power, small-form-factor designs
will be needed. This reference design
is an under-10-W, non-isolated SEPIC
LED driver specifically laid out for
residential downlighting.
Web Links
Key Features
• Single-stage SEPIC, PFC + LED current regulation
• Low-cost, low-component count
• Drives 3 to 6 LEDs at 350 mA
Datasheets, user’s guides, samples:
www.ti.com/sc/device/TPS92010
Design Specifications
Parameter
Minimum
Typical
Maximum
Unit
Input voltage
120
­—
290
VAC
Output voltage
­—
­—
24
Volts
Output current
—
0.350
—
Amp
PMP3522 Schematic
F1
0.5A
AC IN
120 - 290VAC
J1
1
2
C1
0.047µF
275VAC
L1
1mH
+
L2
1mH
AC
AC
D1
RH05-T
D2
BZX84C20T
C3
1nF
R1
220K
R2
220K
L3
180µH
R3 TP2
220K
1
C2
0.1µF
3
C5
10µF
C4
47nF
+
D3
R4
100 MMBD4148
C6
0.1µF
TPS92010
1
2
3
4
SS
FB
PCS
GND
LPM
VSD
VDD
GD
8
7
6
5
+
C7
R15
33.2K
4
D4
MURA160T3
C9
470µF
R7
100K
Q1
FCD4N60
R8
R10
100
D6
BAT54S
2
0.1µF
10
C10
1nF
2
+
R9
0.1
+
1
C11
10µF
R12
6.11K
J2 3 - 6 LEDs
@ 350mA
LET RTN
D5
BZX84C27T
R11
100
R13
3.3
R14
3.3
Q2
MMBT3904LT1
For more reference designs, see: www.ti.com/powerreferencedesigns
LED Reference Design Cookbook
Texas Instruments 2Q 2010
7
TPS92010 PMP3522
➔
Laid Out for Bulb Replacement
10-Watt, AC/DC LED Driver
Control Loop Frequency
Regulation
Efficiency
Texas Instruments 2Q 2010
LED Reference Design Cookbook
8
Dimmable LED Lighting Driver for Lightbulb Retrofit Apps
➔
TPS92210EVM
NEW!
Description
The TPS92210EVM employs
quasiconstant “on” time that enables
single-stage PFC in an isolated
flyback configuration. Intended for
Description
TPS92210EVM
High efficiency, PFC
and TRIAC dimmable
LED lighting driver
Parts
TPS92210
VOUT (DC)
Range
VIN Range
180 V
Key Features
• AC/DC TRIAC dimmable LED driver
with PFC
• Ideal for residential lighting
• Single stage (PFC and LED current regulation)
• 12- to 25-W applications
• Deep TRIAC dimming capability
low-power lighting applications, it
can be packaged in a variety of ways,
including individual lamp designs and
generic PCB form factors for many
types of lighting. The driver preserves
dimmer holding current and features
dual-slope output control to improve
dimming linearity when used with
common TRIAC-based phase-control
dimmers. The TPS92210 controller
is programmed to operate at a fixed
frequency with a constant “on” time
for the internal switch that drives the
primary power FET.
The TPS92210EVM is a natural powerfactor-correction (PFC) LED lighting
driver controller with advanced energy
features to provide high-efficiency
control for LED lighting applications.
The TPS92210EVM is capable of
providing a high power factor, TRIAC
dimming, load protection and extended
life in a small space at low cost.
265 V
17 V
21 V
Web Links
www.ti.com/tps92210evm
Number
of LEDs
IOUT
(max)
POUT
(max)
Eff.
PFC
ISO
Dimming
In
Dimming
Out
6
350 mA
11 W
83%
Yes
Yes
TRIAC
Linear
TPS92210EVM Block Diagram
Primary
Secondary
C
Supplemental
Load
Phase Angle
Detection
TPS92210
1
FB
VDD 8
4
OTM
3
PCM
CGD 8
7
GND
CSD 5
OOP 2
FEEDBACK
Current Reference
and
Difference Amplifier
RCS
For more reference designs, see: www.ti.com/powerreferencedesigns
LED Reference Design Cookbook
Texas Instruments 2Q 2010
Dimmable LED Lighting Driver for Lightbulb Retrofit Apps
9
TPS92210EVM
➔
LED Lighting Driver’s Efficiency
LED Lighting Driver’s Total Harmonic Distortion
LED Lighting Driver’s Current Regulation
LED Lighting Driver’s Current Ripple
LED Lighting Driver’s PFC
Texas Instruments 2Q 2010
LED Reference Design Cookbook
10
Low-Cost AC/DC TRIAC Dimmable Driver for Lightbulb
➔
TPS92001 PMP4981
Description
Key Features
• Low-cost, AC/DC TRIAC dimmable
LED driver lighting reference design
• Ideal for residential lighting
• LED ripple current 100% (120 Hz)
• 6- to 11-W applications
• Deep TRIAC dimming capability
• No electrolytic capacitors option
The PMP4981’s dimming function
allows the string of LEDs to be dimmed
to very low levels without flickering or
stroboscopic effects. Current is drawn
from the TRIAC only when needed,
providing high efficiency with a nonisolated driver for a very-low-cost
solution. This single stage provides
high reliability, long life and high
performance.
The PMP4981 is a reference design
for an LED driver in a lightbulbreplacement circuit. The design is
optimized to function with AC input
sources that may be fed through
an industry-standard TRIAC-based
phase-cut dimmer.
Design Specifications
Description
PMP4885 lowcost offline
LED lighting driver
Parts
VIN
(AC)
Range
VOUT
(DC)
Range
TPS92001
90
24
TLC372
130
32
Number
of LEDs
IOUT
(max)
POUT
(max)
Eff.
PFC
ISO
Dimming
In
Dimming
Out
EVM
7 to 9
450 mA
12 W
79%
No
No
TRIAC
PWM
Paper
PMP4981 Schematic
TP1
TP3
C4
20 VAC
0.047µF
TRIAC Dimmer TP5
200V
C15
0.01µF
200V
1
+
R2
30
D3
RH04-T
TP6
3
AC
4
AC
C1
.1µ
TP2
D1
MURA120
D4
12V
–
L2
470µ
D2
MURA120T3
+
C5
R1
2.10K 1µF
Q1
FZT757A
2
C6
100p
D5
301V
R5
2K
R3
301K
R4
10
VDD
R10
28K
C7
.01U
C9
1000P
REF
R18
8.06K
Q4
3906
R17
560
TP9
R15
200K
C14
1µ
R16
40.2K
R19
40.2K
U1
TPS92001
1
2
3
4
FB REF
SS VDD
RT1 OUT
RT2 GND
C10
.01µ
D6
15V
TP8
REF
8
7
6
5
TP7
C2
0.1U
L1
1.2mH
C12
1.0µ
C13
1.0U
TP4
C3
4.7µF
LED+
LED–
Q2
FQT4N25
R6
1
R8
1
R7
10K
VDD
8
R11
100K
+
R12
1K
4
C8
.01µ
1
R9
10K
U2:A
TLC372CD
C11
.01µ
D7 15V
7
5
6
U2:B
TLC372CD
Q3
BF720
For more reference designs, see: www.ti.com/powerreferencedesigns
LED Reference Design Cookbook
Texas Instruments 2Q 2010
Low-Cost AC/DC TRIAC Dimmable Driver for Light
11
TPS92001 PMP4981
➔
Line Current and Voltage – Dimmer at Full Power Position
LED Current and Voltage – Dimmer at Half Power Position
LED Current and Voltage – Dimmer at Full Power Position
Rectified AC (Top) and LED Current (Bottom) —
High Conduction Angle
Line Current and Voltage – Dimmer at ~ Half Power Position
Rectified AC (Top) and LED Current (Bottom) —
Low Conduction Angle
Texas Instruments 2Q 2010
LED Reference Design Cookbook
12
100-Watt, Constant-Current, Non-Isolated Driver with PFC
➔
UCC28810/UCC28810EVM-002
Description
The UCC28810EVM-002 evaluation
module (EVM) is a constant-current
non-isolated power supply for LED
lighting applications that require high
brightness, such as street, parking
or area lighting. The reference design
converts the universal mains (90 to
265 VRMS) to a 0.9-A constant-current
source to drive a 100-W LED load.
The UCC28810EVM-002 is a twostage design. The first stage, a
transition-mode circuit with PFC,
ensures that the design meets various
standards such as the EN61000-3-2.
The PFC circuit converts the AC input
to a regulated DC voltage, which can
be configured as a boost-follower PFC
or a fixed output voltage. The boost-
Key Features
• High-power AC/DC LED driver with PFC
• Ideal for street, parking or area lighting
• Universal-input, non-isolated design
• Tightly regulated LED current
• PWM dimming, 200 Hz to 1 kHz
• High efficiency through dimming
• Active power-factor correction
follower PFC tracks the AC input’s
peak voltage for increased efficiency
at low-line operation. The PFC’s DC
output voltage is then regulated to a
fixed value in the region of 396 VDC.
The second stage of the design also
uses transition mode but is configured
as a buck converter. It converts the
PFC output voltage to a fixed 0.9A current to drive an LED load. The
second stage accepts PWM dimming
inputs (either externally or from an
onboard circuit) and appropriately
toggles itself on or off.
Web Links
Datasheets, user’s guides, samples:
www.ti.com/sc/device/UCC28810
Reference designs:
www.ti.com/powerreferencedesigns
EVM:
www.ti.com/ucc28810evm-002
Design Specifications
Parts
VIN
(AC)
Range
VOUT
(DC)
Range
UCC28810
90
55
UCC28811
265
100
Description
UCC28810
EVM002 100-W
LED lighting driver
Number
of LEDs
IOUT
(max)
POUT
(max)
Eff.
PFC
ISO
Dimming
In
Dimming
Out
EVM
15-30
900 mA
100 W
93%
Yes
No
PWM
PWM
Yes
UCC28810EVM-002 Block Diagram
PFC Output
Bias
Bias
UCC28811
1 VSENSE VDD 8
UCC28810
6 GND
TZE 5
2 EAOUT
VDD 8
3 VINS
2 EAOUT GDRV 7
3 VINS
4 ISENSE
GDRV 7
GND 6
TZE 5
1 VSENSE ISENSE 4
LED PWM
Input
Enable
PFC Boost
LED Reference Design Cookbook
Critical Conduction Mode
Low Side Buck Current Source
Primary
Gnd
Texas Instruments 2Q 2010
100-Watt, Constant-Current, Non-Isolated Driver with PFC
13
UCC28810/UCC28810EVM-002
➔
Efficiency and Power Factor vs. Line Voltage
Line Regulation 30 LEDs at 900 mA, (98 W)
UCC28810EVM-002 efficiency and power factor vs. line voltage 30 Cree XRE LED’s
at 900 mA.
LED current regulation as a function of line voltage.
PWM Dimming Waveforms
PWM Dimming Response
UCC28810EVM-002 transition mode buck PWM response. Ch1: Buck VIN, Ch2: Buck VDS,
Ch3: LED current (0.5 A/Div), Ch4: LED voltage. Ch1 and Ch4 share GND reference.
UCC28810EVM-002 transition mode buck PWM response (expanded). Ch1: LED VOUT,
Ch2 PWM, Ch3 buck inductor current 500 mA/Div, Ch4 VDS Ch1 and Ch4 Share GND
reference.
THD Factor vs. Line Voltage
UCC28810EVM-002 THD vs. line voltage 30 Cree XRE LED’s at 900 mA.
Texas Instruments 2Q 2010
LED Reference Design Cookbook
14
110-Watt, Constant-Current, Isolated Driver with PFC
➔
UCC28810/UCC28810EVM-003: SimpLEDrive™
Description
The UCC28810EVM-003 evaluation
module (EVM) is an off-line AC-toDC LED current driver with PFC for
applications such as street, high-bay,
and medium- or large-infrastructure
lighting. The UCC28810EVM-003 is
a three-stage converter design that
delivers up to 110 W. The first stage
is a universal input boost-PFC circuit
providing a 305- to 400-VDC output.
The second stage is a low-side buck
circuit providing the controlled current
source, and the third stage is a series
of two half-bridge DC/DC transformers
that provides isolation of multiple LED
strings.
This patent-pending solution provides
an easily scalable and cost-effective
method of driving multiple LED strings.
The UCC28810EVM-003 implements
Key Features
• SimpLEDrive™ high-power
dimmable AC/DC LED driver with PFC
• Ideal for street, high-bay or infrastructure lighting
• Isolated from the AC line
• Readily scalable to higher power
levels
• LED current matching between
strings
• High efficiency and power density
• Active power-factor correction
single-reference current control and
universal dimming (via AM or PWM)
for all LEDs. The reference design
effectively drives a large number of
LEDs connected in series, but the
voltage on the LED strings is safe
(low) and isolated from the AC line.
The multistring architecture is more
cost-effective than an architecture
with a constant voltage plus a buck
stage for each LED string. The LEDdriver architecture is readily scalable
to very high power levels. Excellent
LED current matching between strings
is achieved with this architecture.
The UCC28810EVM-003 achieves
high efficiency (91%), high power
density and a high power factor. The
control stage is a simple and robust
design, and the EVM protects against
scenarios with open and short LED
strings.
Web Links
Reference designs:
www.ti.com/powerreferencedesigns
Datasheets, user’s guides, samples:
www.ti.com/sc/device/UCC28810
EVM:
www.ti.com/ucc28810evm-003
Design Specifications
Description
UCC28810
EVM003 100-W
isolated multistring LED lighting
driver w/multiple
transformers
Parts
VIN
(AC)
Range
VOUT
(DC)
Range
Number
of LEDs
IOUT
(max)
POUT
(max)
Eff.
PFC
ISO
Dimming
In
Dimming
Out
EVM
90, 265
22 V, 60 V
4X
(7 - 15)
500 mA
110 W
91%
Yes
Yes
PWM
PWM
Jul-09
UCC28810
UCC28811
TPS92020
UCC28810EVM-003 Block Diagram
PFC Output
Bias
Bias
UCC28811
1 VSENSE VDD 8
UCC28810
6 GND
TZE 5
2 EAOUT
VDD 8
3 VINS
2 EAOUT GDRV 7
3 VINS
4 ISENSE
GDRV 7
GND 6
TZE 5
1 VSENSE ISENSE 4
LED PWM
Input
Enable
PFC Boost Follower
LED Reference Design Cookbook
Primary
Gnd
Critical Conduction Mode
Low Side Buck Current Source
Texas Instruments 2Q 2010
110-Watt, Constant-Current, Isolated Driver with PFC
15
UCC28810/UCC28810EVM-003
➔
Efficiency vs. Line Voltage
IOUT Matching vs. Line Voltage
UCC28810EVM-003 efficiency vs. line voltage and load 4 x 15 Cree XRE LED’s at
500 mA.
UCC28810EVM-003 IOUT matching vs. line voltage 4 x 15 Cree XRE LED’s at 500 mA.
Power Factor vs. Line Voltage
UCC28810EVM-003 AC Input Current During PWM Dimming
UCC28810EVM-003 power factor vs. line voltage 4 x 15 Cree XRE LED’s at 500 mA.
Ch1: VBUCK+, Ch2: Buck VDS, Ch3: AC line current 1A/Div, Ch4: VBUCK - Ch1 and Ch 4
share GND reference.
+50 - 60V
Bias
TPS92020
+50 - 60V
+50 - 60V
VCC
RT
GD1
DT
GND
SS
GD2
+50 - 60V
Texas Instruments 2Q 2010
LED Reference Design Cookbook
16
240-W LED Lighting System
➔
TPS92020, UCC28810/1
Description
NEW!
Web Links
This reference design uses the
UCC28810, UCC28811 and TPS92020 for an isolated, off-line,
240-W LED driver for high-bay and
streetlight applications. The driver
has three stages: a power-factorcorrection (PFC) stage, a buck stage
and an isolation stage. The PFC and
buck stages both operate in criticalconduction mode. The isolation stage
is a half-bridge converter with an
option to adopt a multi-transformer
configuration. A constant output
current is controlled within the buck
stage to provide 3 A to the LED strings,
with an output voltage ranging from 70 V to 85 V.
Datasheets, user’s guides, samples:
www.ti.com/sc/device/TPS92020,
www.ti.com/sc/device/UCC28810 or
www.ti.com/sc/device/UCC28811
Design Specifications
Parameter
Test Conditions
Minimum
Typical
Maximum
Unit
Input voltage
—
108
120/277
305
VRMS
Power factor
—
0.990
—
—
—
Output current
—
—
3
—
Amp
Output ripple
COUT = 4.4 µF
—
300
—
mAPP
Output voltage
—
70
—
85
Volts
Efficiency
—
87
—
—
%
TPS92020, UCC28810/1 Schematic
PFC Output
CC Buck Output
+70V to 85V
3A
Bias
UCC28811
UCC28810
Bias
TZE 5
1
GND
2
EAOUT VDD 6
3
VINS GDRV 7
4
VSNS ISNS 8
VDD 8
≈
Bias
TPS92020
1
VSNS
2
EAOUT GDRV 7
3
VINS
GND 6
RT
GD1
4
ISNS
TZE 5
DT
GND
SS
GD2
VCC
≈
LED PWM
Input
ENABLE
Primary
GND
PFC Boost Follower
Critical Conduction Mode
Low Side Buck Current Source
Half Bridge
DC Transformer
For more reference designs, see: www.ti.com/powerreferencedesigns
LED Reference Design Cookbook
Texas Instruments 2Q 2010
240-W LED Lighting System
17
TPS92020, UCC28810/1
➔
Power Factor
Power Factor
Efficiency
Efficiency
Load Regulation
Load Regulation
Texas Instruments 2Q 2010
LED Reference Design Cookbook
18
Constant Current Driver with PFC
➔
UCC28810 PMP4501
Description
Key Features
• Isolated single stage LED driver
• Naturally high PFC
• 90% efficient
• Universal input voltage range
• 700-mA output current
• Low LED ripple current
prevents dangerous output voltages
from occurring during open-string
conditions. A current-sense amplifier
reduces the sensing resistor’s power
dissipation, thus increasing overall
efficiency. The internal reference
voltage of the operational amplifier
achieves excellent LED-current
regulation versus output power and
input voltage. The PMP4501 achieves
high efficiency (90% peak), high power
density and a high power factor. The
reference design protects against
scenarios with open and short LED
strings, and the control stage is a
simple and robust design.
The PMP4501 is an isolated, off-line,
AC-to-DC LED-current driver with PFC
for applications such as commercial
fixture lighting and general isolated
LED drivers. The PMP4501 is a singlestage flyback PFC converter that
delivers up to 34 W with a 180- to 265-VAC input voltage while providing
a 10- to 48-V output voltage at a
constant output current of 700 mA
±2%.
The PMP4501 implements secondaryside current control for the LED
string. Overvoltage protection
Web Links
Datasheets, user’s guides, samples:
www.ti.com/sc/device/UCC28810
Design Specifications
Description
UCC28810
PMP4501 34-W
Secondary side
current loop
Parts
VIN
(AC)
Range
VOUT
(DC)
Range
UCC28810
180
10 V
TL103W
265
48.5 V
Number
of LEDs
IOUT
(max)
POUT
(max)
Eff.
PFC
ISO
Dimming
In
Dimming
Out
EVM
3-13
700 mA
34 W
89%
Yes
Yes
No
No
Reference
Design
R1
100K
R2
C2
22K 10nF
R3
R4
22K
100K
D4
S1KB
Q1
D7
PZT2222A MURA140T3
C1
0.1µF
2
L2
20mH
D1
DF06S
L1
1mH
3
C3
0.15µF
275VAC
1
F1
1A/250V
4
TP2
TP1
PMP4501 Reference Design Schematic
D2
BYG10M
R6
100K
D3
BYG10M
R9
1.5M
C1
1µ
C6 +
100µF
25V
R10
6.98K
U2
UCC28810D
R14
1.5M
1
2
3
4
R19
11K
C9
22nF
VDD 8
VSNS
7
EAOUT GDRV
6
GND 5
VINS
TZE
ISNS
R22
330
C14
DNP
C11
.1µ
D6
BAS16
R7
10K +
D8
15V
D11
MBR0520L
C12
R20
10pF
47.5K
R8
C7 2.2
47µF
63V
R16
10
T1
G094010LF
5
A
D5
PDU540-13
7
4
8
2
9
1
10
C8
1000pF Y1
C4 +
470µF
63V
Q2
STB7NK80ZT4
10V...48V . 700mA
GND
R5
0.15
C5
470µF
63V
R13
1K
R12
23.7K
D9
MURA120T3
6
D10
51V
5
7
C10
47µF
35V
Q3 3904
+
R17
2.49K
U1:B
TL103WID
TP3
TP4For Test
Purpose
Only.
R17=50Ω
TP5
D12
R23 12V
0.82
R24
2.21K
4
1
R27
10K
2
3
J1
R11
1K
R18
10K
R21
47.5K
+
1
2
D13
BAW56
U3
+
TCMT1107 C15
47µF
35V
C13
1µ
8
1
C16
1µF
4
R25
10K
2
3
R28
3.32K
R26
10K
U1:A
TL103WID
C17
220µF
For more reference designs, see: www.ti.com/powerreferencedesigns
LED Reference Design Cookbook
Texas Instruments 2Q 2010
Constant Current Driver with PFC
19
UCC28810 PMP4501
➔
PMP4501 Board
IOUT Regulation vs. Rectified-Equivalent Line Voltage and
Output Power
Efficiency vs. Rectified-Equivalent Line Voltage and
Output Power
Output Current Ripple. Input Voltage = 230 VAC, Output
Voltage = 48 V @ 700 mA
Power Factor vs. Line Voltage and Output Power
AC Input Current and Voltage at Full Load and Nominal
Input Voltage
Texas Instruments 2Q 2010
LED Reference Design Cookbook
20
LED Streetlight Driver Based on SEPIC Technology
➔
UCC28810 PMP3976
Description
The PMP3976 circuit shown below was
designed for a commercial LED lighting
fixture. The SEPIC topology has the
advantage over a flyback converter in
that it clamps the switching waveforms
on the power semiconductor, allowing
the use of lower voltage and hence
more efficient parts. This provides
an estimated 2% improvement
in efficiency in this application.
Additionally, there is less ringing in the SEPIC, making EMI filtering easier.
The LED-lighting circuit uses the
UCC28810 transition-mode boost
controller to shape the input-current
waveform. The circuit starts by
charging C6 off the line. Once the
controller is running, its power is
provided by an auxiliary winding on
the SEPIC inductor. A relatively large
output capacitor limits LED ripple
current to 20% of the DC current. As
a side note, the AC flux and currents
in the transition-mode SEPIC are
quite high, so Litz wire and low-loss
Key Features
• Non-isolated single LED string driver
• 92% efficient solution
• SEPIC control boosts for high voltage
• Natural single stage with >0.9 PFC
• Low-cost solution with few external
parts
• Meets European harmonic requirements
core material are required to reduce
inductor losses.
The following material presents lab
results from a prototype that was built
to match the schematic. Efficiency
is quite high over the European line
range, peaking at 92%. This good
efficiency was achieved by limiting the
ringing on the power semiconductors.
Also, as can be seen from the current
waveform, the power factor is quite
good at over 96%. Interestingly, the
waveform is not purely sinusoidal but
shows some steepness on the rising
and falling edges. This is because the
circuit measures switch current but not
input current. However, the waveform
is good enough to pass the European
requirements for harmonic currents.
Web Links
Datasheets, user’s guides, samples:
www.ti.com/sc/device/UCC28810
Reference designs:
www.ti.com/powerreferencedesigns
Design Specifications
Parameter
Minimum
Typical
Maximum
Unit
Input voltage
150
—
264
VAC
Output voltage
—
—
300
Volts
Output current
—
0.350
—
Amp
PMP3976 Schematic
150VAC to 240VAC Input
F1
1.6A/250V
LINE
L1
4mH
D2
KBP06G
TP3
2
3
NTRL
C102
0.22µ
4
1
TP1
C101
0.22µF
1
+
2
3
AC
R1
200K
0.25W
AC
–
RT1
2.5Ω
4
1
R3
200K
0.25W
U1
TLV431AIDBZ
R4
1.1 MEG
0.25W
R11
1.1 MEG
0.25W
1
1
R9
100K
U2
UCC28810D
1
R15
15K
1
R7 200K
C4
100pF
R8
100K
R5 49.9K
C100
100pF
1
R20
100K
R16
1K
1
2
3
4
VSNS
VCC 8
COMP
DRV 7
MULTIN GND 6
CS
ZCD 5
1
C11
2.2µF
C9
22µF
C12
1000pF
R18
15K
1
1
LED Reference Design Cookbook
Texas Instruments 2Q 2010
UCC28810 PMP3976
PMP3976 Rev B Demo Board
21
➔
LED Streetlight Driver Based on SEPIC Technology
Power Factor
The circuit is built on a PMP3976 Rev A PWB.
C1 0.47µF
T1
750µH
C2
0.22µF
1
1
7
2
8
1
4
+
C3
330µF
0
1
TP2
D1 MUR8100E
5
D3 MMSD914
J1
R101
100K
0.5W
R23
20
+
C5
0.1µF
HS1
1
C6
100µF
25V
R10
15K
1
D4
180V
R13
100K
C10
10pF
R19
0.5
1W
1
Texas Instruments 2Q 2010
R6
100K
–LED
C8
1000pF
1
D5
180V
Q1
MMBT2907
Q2
MMBT3904
Q3
SPP06N80C3
R17 301
C7
1000pF
3
TP4
1
R100 10
+
+LED
R2
3.6
1W
R102
100K
0.5W
1
1
2
R12 1K
1
D100 MMSD914
1
TP5
R21 511
TP6
LED Reference Design Cookbook
22
LED Streetlight Driver Based on SEPIC Technology
➔
UCC28810 PMP3976
Harmonic Content
Efficiency
The image above shows a thermal image of the board. The ambient temperature was
26ºC with no forced air flow. The input was 230 VAC.
Harmonic Content
Efficiency and Power Factor
IOUT
VOUT
VIN
LIN
PF
POUT
Losses
Efficiency
%
0.349
245.5
150.4
0.646
0.983
85.65
9.827
89.7
0.349
245.4
176.4
0.544
0.980
85.64
8.398
91.1
0.349
245.3
202.6
0.473
0.979
85.61
8.208
91.3
0.350
245.3
226.3
0.430
0.975
85.86
9.201
90.5
0.350
245.3
248.4
0.399
0.969
85.86
10.184
89.4
0.350
245.3
265.7
0.378
0.962
85.86
10.763
88.9
The harmonic content and the EN61000-3-2 Class C (lighting equipments) Limits are
shown above; input voltage was set to 230 VAC.
IOUT
VOUT
VIN
LIN
PF
POUT
Losses
Efficiency
%
0.348
303.9
149.9
0.803
0.988
105.75
13.168
88.9
0.349
303.3
175.2
0.677
0.983
105.85
10.742
90.8
0.349
303.8
199.9
0.588
0.984
106.03
9.634
91.7
0.349
303.3
224.8
0.527
0.983
105.85
10.604
90.9
0.349
303.2
249.8
0.482
0.978
105.82
11.938
89.9
0.349
303.0
264.2
0.461
0.975
105.75
13.004
89.0
For more reference designs, see: www.ti.com/powerreferencedesigns
LED Cookbook
Texas Instruments 2Q 2010
LED Streetlight Driver Based on SEPIC Technology
23
UCC28810 PMP3976
➔
Frequency Response
Diode Voltage Waveform
The frequency response of the feedback loop is shown in the plot above. The input was set
to 220 VAC. The lower gain plot was taken with a 300 V output. The upper gain plot was
taken with a 250 V output.
The image above shows the voltage on the anode of D1. The input was set to 250 VDC.
Line Voltage and Current Waveform
Inductor Winding Currents
The image above shows the input voltage and current. The input voltage was 230 VAC.
MOSFET Voltage Waveform
The image above shows the drain-to-source voltage on Q3. The input was set to 250.
Texas Instruments 2Q 2010
The two images above show the currents in the individual windings of the inductor.
LED Reference Design Cookbook
24
25-Watt Dimmable Driver with PFC
➔
UCC28810/UCC28810EVM-001
Description
resistance is used across the line or
in series that would reduce efficiency.
Valley switching is implemented in
the UCC28810EVM-001 to improve
efficiency. A fast start-up circuit is also
implemented, so there is no perceived
delay from switching to illumination.
Using the UCC28810 transitionmode boost IC with PFC in a flyback
converter yields a valley-switching
design that can achieve 90% efficiency
and a high power factor over a
universal wide input-voltage range.
The UCC28810EVM-001 also operates
over a universal wide input-voltage
range. High-performance TRIAC
dimming detection and regulation
adjustment are achieved with minimal
impact on efficiency.
The UCC28810EVM-001 evaluation
module (EVM) is a 25-W TRIAC
dimmable and single-stage
flyback converter with PFC. The
UCC28810EVM-001 provides
approximately 36 V at a constant 700-mA (undimmed nominal) load
current to power a string of highbrightness LEDs. This EVM allows
the evaluation of the UCC28810 LED
lighting controller in an application
where LEDs can be used for general
illumination applications that require
dimming.
Web Links
Reference designs:
www.ti.com/powerreferencedesigns
Datasheets, user’s guides, samples:
www.ti.com/sc/device/UCC28810
An input-filter damping network
ensures operations with most TRIACbased wall dimmers. No extra
EVM:
www.ti.com/ucc28810evm-001
Design Specifications
Description
UCC28810
EVM001 25-W
PFC dimmable
LED driver
Parts
VIN
(AC)
Range
UCC28810
85
TPS3808
305
VOUT
(DC)
Range
Number
of LEDs
IOUT
(max)
POUT
(max)
Eff.
PFC
ISO
Dimming
In
Dimming
Out
EVM
33
10
700 mA
25 W
89%
Yes
Yes
TRIAC
Linear
Yes
UCC28810EVM-001 Block Diagram
High
Voltage
Startup
Input Filter
and Bridge
UCC28810
Dimmer
1
VSENSE
2
EAOUT
3
VINS
4
ISENSE
Primary
Bias
VDD
8
GDRV
7
GND
6
TZE
5
Secondary
Bias
Zero
Energy
Detect
Triac
Dimming
Detection
Current
EA
Voltage Limit
EA
LED Reference Design Cookbook
Texas Instruments 2Q 2010
25-Watt Dimmable Driver with PFC
25
UCC28810/UCC28810EVM-001
➔
Efficiency vs. Line Voltage
Output Current vs. Line Voltage
Efficiency as a function of line voltage. 10 Cree XLamp® 7090 XR-E, white, 700 mA LEDs
connected in series was used for the load.
Load current as a function of line voltage. 10 Cree XLamp® 7090 XR-E, white, 700 mA
LEDs connected in series was used for the load.
Power Factor vs. Line Voltage
Triac Dimming Detection Circuit Waveforms –
Deep Dimming
Power factor as a function of line voltage.10 Cree XLamp® 7090 XR-E, white, 700 mA
LEDs connected in series was used for the load.
Total Harmonic Distortion vs. Line Voltage
Triac Dimming Detection Circuit Waveforms –
Light Dimming
Total harmonic distortion as a function of line voltage. 10 Cree XLamp® 7090 XR-E, white,
700 mA LEDs connected in series was used for the load.
Texas Instruments 2Q 2010
LED Reference Design Cookbook
26
Nonsynchronous Boost LED Driver
➔
TPS40211 PMP4026
Description
The TPS40211 is a wide-input-voltage
(4.5- to 52-V), nonsynchronous
boost controller. It is suitable for
topologies that require a grounded
source n-channel FET such as boost,
flyback, SEPIC and various LEDdriver applications. The TPS40211
features a programmable soft start,
overcurrent protection with automatic
retry, and a programmable oscillator
frequency. Current-mode control
provides improved transient response
and simplified loop compensation. The
feedback pin has a reference voltage
of 260 mV to help reduce the power
usage and cost of the sense resistor.
The PMP4026 circuit shown below was
designed with an automotive inputvoltage range. The driver was built to
operate under low-power to nominal
battery conditions and to survive
load-dump incidents. The TPS40211
was chosen for this application due
to its low feedback voltage and wide
Key Features
• Wide 4.5- to 52-V input range
• Low-cost non-synchronous boost
• High efficiency from low 260-mV
VREF
• Simple loop compensation
• Supports versatile SEPIC topology
input-voltage range. The application,
powered directly from VBAT, can have
a string of up to ten 700-mA LEDs in
series or two parallel strings with up to
ten 350-mA LEDs in each string.
An additional reference design is
available. This design is a 700-mA,
nonsynchronous boost current
regulator for an LED driver. It has an
8- to 18-V input and a 20- to 35-V
output. It can be found along with a
demonstration board at:
Web Links
Datasheets, user’s guides, samples:
www.ti.com/sc/device/TPS40211
http://focus.ti.com/docs/toolsw/
folders/print/tps40211evm-352.html
Design Specifications
Parameter
Minimum
Typical
Maximum
Unit
Input voltage
9
—
16
VDC
Output voltage
—
—
40
Volts
Output current
—
0.700
—
Amp
Switching frequency
—
150
—
kHz
PMP4026 Schematic
1
9 - 18 VIN
GND
C8
3.3µF
R1
249K
D100(R6)
3.3V
1
2
3
4
5
C4
4700pF
Q100
2N7002DICT
R100
10K
2
C12A
3.3µF
50V
VBP
C1
470pF
1
D1
MBRS260
C5
0.1µ
ENAB
TPS40211DGS
3
2
33 µH
R2
15K
RC
VDD
SS
VBP
SD
GDRV
COMP ISNS
FB
GND
10
9
8
7
6
Freq = 150 KHZ
R5
49.9K
8765 D
C7
1µ
Q1
Si4858
4G
C12B
3.3µF
50V
48V @ 0.7A
GND
D2
47V
S
R4A
2
321
R10
1.21K
C9
100pF
R11
0.01
R9
49.9
R3
249K
For more reference designs, see: www.ti.com/powerreferencedesigns
LED Reference Design Cookbook
Texas Instruments 2Q 2010
Nonsynchronous Boost LED Driver
27
TPS40211 PMP4026
➔
Startup
Output Ripple Current
The input voltage was set at 12 V, with 0.15 (LED) + 1 (resistor) A load on the outputs.
The image was taken with a 1.15 A/20 V load. Top waveform is FET drain, bottom is
LED current.
Efficiency
Control Loop Frequency Response: 12 V input; 1.15 A Load
Total output current was 1.15 A, output voltage was 20 volts.
Load Regulation of Outputs
Load Transients
Output response to driving TP%. The input voltage was set to 12 V.
Texas Instruments 2Q 2010
LED Reference Design Cookbook
28
Wide-Input DC Voltage Range SEPIC Driver
➔
TPS40211 PMP3943
Description
Key Features
• Wide 4.5- to 52-V input range
• Low-cost non-synchronous boost
• High efficiency from low 260-mV
VREF
• Simple loop compensation
• Supports versatile SEPIC topology
load-dump incidents. The TPS40211
was chosen for this application due
to its low feedback voltage and wide
input-voltage range.
The TPS40211 is a wide-inputvoltage (4.5- to 52-V) nonsynchronous
boost controller. It is suitable for
topologies that require a grounded
source n-channel FET such as boost,
flyback, SEPIC and various LEDdriver applications. The TPS40211
features a programmable soft start;
overcurrent protection with automatic
retry; and a programmable oscillator
frequency. Current-mode control
provides improved transient response
and simplified loop compensation. The
feedback pin has a reference voltage
of 260 mV to help reduce the power
usage and cost of the sense resistor.
An additional reference design is
available. This design is a 700-mA,
nonsynchronous boost current
regulator for an LED driver. It has an
8- to 18-V input and a 20- to 35-V
output. It can be found along with a
demonstration board at:
Web Links
Datasheets, user’s guides, samples:
www.ti.com/sc/device/TPS40211
www.ti.com/sc/device/TPS40211evm
Design Specifications
The PMP3943 circuit shown below was designed with an automotive
input-voltage range. The driver was
built to operate under low-power
battery conditions and to survive Parameter
Minimum
Typical
Maximum
Unit
Input voltage
8
—
40
Volts
Output voltage
—
13
—
Volts
Output current
—
0.350
—
Amp
Switching frequency
—
300
—
kHz
PMP3943 Schematic
VIN
GND
8-40
J1
L2
100µH
1
1
2
C8
3.3µF
2
R6
0
3
R1
249K
C1
220pF
U1
TPS40211DGS
1
2
3
4
5
C2
0.22µF
C3
47pF
RC
VDD
SS
VBP
SD
GDRV
COMP ISNS
FB
GND
10
9
8
7
6
Freq = 380 KHZ
C15
C7
1µF
R7
10
Short L4
L4
0
4
C5
0.1µF
8765
D1
8180-13
LEDC
321
C9
0.1µF
LEDA
C13
10µF
3.3µF
03
4
13V @ 350mA
Tested with LEDs
Giving 12.3 V
R10
1k
R100
10K
R14
0.75
D2
18V
R11
0.10
C4
4700pF
R2
0
R5
49.9
R9
49.9
LEDC
For more reference designs, see: www.ti.com/powerreferencedesigns
LED Reference Design Cookbook
Texas Instruments 2Q 2010
Wide-Input DC Voltage Range SEPIC Driver
29
TPS40211 PMP3943
➔
Current Loop Frequency Response
3 Green and 1 Red OSRAM LEDs Used as Load for Vf About 12 V
VIN Volts
IIN mA
VOUT1 Volts
IOUT1 mA
Efficiency %
40.22
123.6
12.27
341.8
84.4
20.11
238.5
12.27
341.3
87.3
7.93
619.4
12.27
341.3
85.3
Regulation and efficiency: 25 degrres Celsius ambient. Target IOUT was 350mA, hence actual current is 2.5% low.
When Diode Load is Opened, VOUT Goes to About 18 V
VIN Volts
IIN mA
VOUT1 Volts
IOUT1 mA
40.42
8.79
18.44
0
20.08
10.75
18.41
0
8.00
19.12
18.40
0
VIN Volts
IIN mA
VOUT1 Volts
IOUT1 mA
40.14
21.24
0.694
341.6
20.06
34.20
0.694
341.5
8.00
77.70
0.694
341.4
Short Circuit: Output Current Holds Steady
Texas Instruments 2Q 2010
LED Reference Design Cookbook
30
TMS320C2000™ PLC Modem Evaluation Kit
➔
TMDSPLCKIT-V1
NEW!
Description
Power-line communication (PLC) is
an inexpensive way to add lighting
control to existing or new buildings
and infrastructures without laying
down new control cabling. The
TMDSPLCKIT-V1 is a PLC evaluation
kit based on the C2000™ series of
real-time microcontrollers. It operates
in both OFDM and S-FSK modulation
schemes and has data rates of up to
76.8 kbps.
The kit comes with an easy-to-use GUI
that makes testing the communications
link intuitive and simple.
Web Links
Specifications
• OFDM and S-FSK modulation
schemes
• Data rates of up to 76.8 kbps for one
phase (phase selection is provided)
• PLC system on module (SoM) with interface to host controller (I2C, SPI, SCI)
• Compatible with CENELEC EN50065
and IEC 6100-3 standards
• Operating frequency range: 24 to 94.5 kHz (CENELEC A band. B band to release in 1Q10.)
• Universal AC-voltage input (85 to 270 VAC)
www.ti.com/plcevm
Datasheets, user’s guides, samples:
www.ti.com/sc/device/OPA564 or
www.ti.com/sc/device/PGA112
TMDSPLCKIT-V1 Block Diagram
TMS320F28x
HV Cap
Coupling
Transformer
Line Driver
OPA564
PWM
Out
PGA112
12-Bit
ADC
Flexible
PLC
SW
Engine
Surge Protector
Receive Filter
Power Line
PLC Modem Implementation on TMS320F28x 32-Bit MCU - Simplified Block Diagram
For more reference designs, see: www.ti.com/powerreferencedesigns
LED Reference Design Cookbook
Texas Instruments 2Q 2010
TMS320C2000™ PLC Modem Evaluation Kit
31
TMDSPLCKIT-V1
➔
PLC Data Signal
PLC Signal Modulated Onto the Power Line 50/60Hz
50- or 60-Hz Power Line
Texas Instruments 2Q 2010
LED Reference Design Cookbook
32
Digital Addressable Lighting Interface (DALI)
➔
DALI Implementation with the MSP430™ MCU
Description
Specifications
Intelligent lighting control can provide
large efficiency gains and energy
savings. The digital addressable
lighting interface (DALI) standard is
becoming increasingly popular for this
application.
• F
ull hardware reference files,
including schematics, Gerber files
and BOM
• Full software libraries
• Support for the entire DALI
command set, including
bidirectional commands
The DALI evaluation kit enables the
designer to run DALI on the popular
MSP430 series of microcontrollers.
Software libraries and hardware
reference files are provided to allow
quick evaluation and development with
the DALI standard.
NEW!
Web Links
Application Note:
www.ti.com/lit/SLAA422
MSP430-Based DALI Reference Design
DALI+
1
4
DALI—
2
3
GND
MSP430™
MCU
1
4
2
3
GND
For more reference designs, see: www.ti.com/powerreferencedesigns
LED Reference Design Cookbook
Texas Instruments 2Q 2010
DC/DC LED Developer’s Kit
33
TMDSDCDCLEDKIT
➔
NEW!
Description
schematics and BOMs all available
for free. For more information, please
see the quick-start guide for the kit.
To download the LED software, please
visit: www.ti.com/c2000tools
The DC/DC LED Developer’s Kit
includes all of the hardware and
software to start experimenting with
and developing a digitally controlled
LED backlighting system. The kit is
based on the Piccolo™ microcontroller
and the controlCARD™ development
platform. One Piccolo MCU is able
to directly control the DC/DC power
stage as well as eight LED strings.
The development board takes 12 to
48 VDC of input and uses a SEPIC
DC/DC topology to buck or boost
the input voltage to a desired level.
This voltage is then fed to four LEDdriving stages, each capable of driving
two LED strings at up to 30 W each.
The kit includes closed-loop, opensource software for both the DC/DC
stage and the LED-lighting stage.
The kit hardware is also completely
open-source, with the Gerber files,
Web Links
Datasheets, user’s guides, samples:
www.ti.com/c2000tools
Key Features
• 12- to 24-VDC input to SEPIC DC/DC
stage, 12- to 40-VDC output
• Four LED-driver stages, each capable
of driving two strings at 30 W
• LED-driver stages can be externally
powered
• Piccolo-based controlCARD
development platform
• Open-source hardware, including
Gerber files, schematics and BOMs
• Closed-loop DC/DC and LED-driving
software, complete with source code
and documentation
Typical Application Schematic
Sepic
3
+
DC
12 V to 48 V
+
1
2
Piccolo™
CPU
PWM-1
32 bit
PWM-1
1
2
3
ADC
PWM-1
12 bit
VREF
13
PWM-1
A
1
B
2
A
3
B
4
A
5
B
6
A
7
B
8
2
3
3
8
4
9
I2C
SPI
UART
Texas Instruments 2Q 2010
LED Cookbook
34
3-Watt Solar Lantern
➔
TPS61165 PMP3598
Description
The TPS61165 operates over a 3- to
18-V input supply and delivers an output
voltage up to 38 V. With its 40-V rated
integrated switch FET, the device drives
up to 10 LEDs in series. It operates at
a 1.2-MHz fixed switching frequency to
reduce output ripple, improve conversion
efficiency, and allow for the use of
small external components. The default
white-LED (WLED) current is set with the
external sensor resistor RSET, and the
feedback voltage is regulated to 200 mV.
In either digital or PWM dimming, the
output ripple of TPS61165 at the output
capacitor is small and does not generate
audible noises associated with common
on/off control dimming. For protection
during open-LED conditions, the
TPS61165 disables switching to prevent
the output from exceeding the absolute
maximum ratings.
incorporates the necessary thermal and
overcurrent protections and has loaddisconnect feature. used for driving three 1-W LEDs or
multiple 50-mA LEDs whos total power
input does not exceed 3 W.
Key considerations for this design are
high efficiency and good LED-current
regulation. The TPS61165 operates in
a constant-current mode to regulate
the LED current. The CTRL pin is used
for the control input for both digital and
PWM dimming. The dimming mode for
the TPS61165 is selected each time
the device is enabled. Analog dimming
has been implemented by varying the
feedback reference. A 20-kΩ variable
resistor can be used to vary the LED
current to achieve dimming. The
converter boosts 6 to 10.5 V at 350 mA and has minimum conversion
efficiency of 85%. This circuit is Key Features
• Boost output up to 38 Vout
• Wide supply voltage 3 V to 18 V
• High efficiency from 200-mV threshold
• PWM dimming
• LED open protection
• 350-mA LED current
Web Links
Reference designs:
www.ti.com/powerreferencedesigns
Datasheets, user’s guides, samples:
www.ti.com/sc/device/TPS61165
Design Specifications
The PMP3598 uses the TPS61165 in a
nonsynchronous boost configuration. An additional circuit built around the
op amp provides the battery undervoltage/charging indications and also
provides ORing between the solar panel
and battery inputs. The circuit also
Parameter
Minimum
Typical
Maximum
Unit
Input Voltage
4.5
6
7.4
Volts
Output Voltage
10.45
10.5
10.65
Volts
Output Ripple
­—
—
50
mV pp
Output Current
0
—
350
mA
Switching Frequency
—
1200
—
kHz
TP3
R3
4.42K
J1
5
2
3
4
TP1
TP2
1
2
D1
BAT54C
R4
2.25M
R6
169K
D4
IN5820
R11
226K
R10
162K
R17
6.81K
4
5
To 28K POT
C3
0.22µF
J3
D6
BZX84C18T
C4
3.3µF
R18
1
U1:B
TL103WID
R7
100K
1
2
LED A
LED C
R21
51.1
R16
1
R13
10K
LED Reference Design Cookbook
R14
59K
7
R5
4.42K
RT1
22K
R8
Open
7
3
C1
0.1µF
6
5
6
R2
10K
R1
1K
2
D5
MBRS120
TP4
FB
VIN
COMP CTRL
GND
SW
PwPd
Q1
Si2343DS
J4
1
TP5
R12
1K
R20
2.61K
L1
10µH
R15
100K
2
R9
169K
1
D3
BAT54C
U2
TPS61165DRV
8
7
6
1
2
3
4
5
PMP3598 Schematic
C2
2.2µF
Texas Instruments 2Q 2010
35
TPS61165 PMP3598
➔
Switching Waveform
3-Watt Solar Lantern
Output Ripple
Open LED Protection
Efficiency
Texas Instruments 2Q 2010
LED Reference Design Cookbook
36
High-Brightness LED Driver with Switch Control
➔
TL4242
NEW!
Description
High-brightness LEDs are becoming
more and more prevalent in all facets
of life. Linear drivers are great for
simple applications that do not
require very high efficiency and for
applications that must have little
or no electromagnetic interference
(EMI). Pulse-width modulation
(PWM) is used for dimming in some
of these applications but can also
introduce EMI. This reference design
uses a simple linear LED driver for
high-brightness applications and
demonstrates one of several methods
of controlling dimming without the
introduction of EMI.
Figure 2 demonstrates the TL4242
used with the TS3A4742 to produce
an LED dimming circuit capable of
switching between 200, 250, 300 and
Figure 1. Simple TL4242 LED Drive Circuit
+18V
TL4242
I
IN
SHDN
GND OUT SENSE
REF
ST
PWM
10KΩ
D
C1
47nF
RREF
Controller
Figure 2. TS3A4742 Dual, Normally Closed Analog Switch Provides
Four Brightness Levels
+18V
TL4242
I
IN
Q
SHDN
TPS7A4533
REF
ST
PWM
GND OUT SENSE
3.3V
IOUT = VREF/RREF
The TL4242’s typical VREF is 0.177 V.
If RREF is set to 2 W, then the
corresponding IOUT will be 88.5 mA.
Q
TPS7A4533
GND
The TL4242 is a linear constant-current
single-channel LED driver capable of
sourcing up to 500 mA. The TL4242
is capable of running from a supply of
up to 42 V so that a large LED string
can be driven through a single device.
Figure 1 shows a simple example of
the TL4242 used to drive four LEDs
(typical VF = 3.5 V). In this design, the
PWM pin is used only to enable and
disable the TL4242. The current is
set through a very simple relationship
between the sense resistor (RREF) and
the voltage at the REF pin (VREF):
350 mA. Changing RREFP, RREFS1
and RREFS2 provides a wide variety of
dimming levels. RREFS1 and RREFS2
must be chosen with the RON of the
switch in mind. Note that each leg
has the same current when it is on,
regardless of the other legs’ current.
and normally closed operation. Care
must be taken to keep the channel
current under 100 mA.
GND
10KΩ
+3.3V
D
TS3A4742
C1
47nF
RREFP
Controller
RREFS2
V+
RREFS1
NC1
IN1
COM1
NC2
IN2
COM2
GND
In the application in Figure 1, the 18-V
supply current is fed directly into the
TL4242 for LED current. The TL4242
also monitors the LED string for an
open condition and sets the status
(ST) pin if an open is detected.
To enable dimming without PWM,
RREF must be changed and is easily
manipulated with a simple analog
switch. The TS3A4742 is chosen (see
Figure 2) because of its low (typically
0.7-W) RON, high-current (100-mA)
capability, dual-switch configuration
Switched Reference Resistors
Primary Reference
Resitor (RREFP)
(RREFS1)
(RREFS2)
Equivalent
Resistance (RREF)
Nominal Output
Current (IOUT)
0.885 W
1.77 W
3.54 W
0.506 W
350 mA
0.885 W
1.77 W
Open
0.590 W
300 mA
0.885 W
Open
3.54 W
0.708 W
250 mA
0.885 W
Open
Open
0.885 W
200 mA
Note: RREFS1 and RREFS2 include RON of the TS3A4742.
For more reference designs, see: www.ti.com/powerreferencedesigns
LED Reference Design Cookbook
Texas Instruments 2Q 2010
High-Brightness LED Driver with Switch Control
37
TL4242
➔
resistance to 1.4 W. This also permits
dual brightness; but the current
through the TS3A4742 is limited to
100 mA per channel, so the brightness
will be lower than when the channels
are in parallel.
2). This is a simple automotive taillight solution for on/off and braking.
The tail light is on when PWM is high
(push-button 1 is not depressed). The
brightness of the tail light is normal
when push-button 2 is not depressed
and brighter when it is depressed.
Choosing a dual switch with a low
RON allows the user to connect
both channels in parallel, thereby
reducing the effective RON. This
parallel approach can reduce the
TS3A4742’s typical RON to 0.35 W.
Figure 3 shows an example using this
parallel approach to generate a dualbrightness design. This application
uses a 0.65-W resistor (RREFS1) in
series with both switches, creating
an effective RREF of 1-W. This leg
will sink 177 mA (88.5 mA through
each switch) when on. Care must be
taken to keep the current through the
analog switch below the maximum
allowed. Additionally, the power
dissipation in the switch package
must be considered. In the case of the
TS3A4742, the maximum continuous
current is 100 mA per channel. Figure 3 also removes the controller
and replaces it with simple pushbutton switches. This design allows
a single button (or other manual
control) to enable the LEDs (simple
push-button 1) and another to set the
brightness level (simple push-button
Web Links
Another option is to hook up the
switches in a serial manner (see Figure 4), thereby doubling the
Datasheets, user’s guides, samples:
www.ti.com/sc/device/TL4242
Figure 4. Switches in Series
+18V
TL4242
I
IN
Q
SHDN
TPS7A4533
GND OUT SENSE
GND
10KΩ
+3.3V
REF
ST
PWM
TS3A4742
D
C1
47nF
V+
RREFS
RREFP
Controller
NC1
IN1
COM1
NC2
IN2
COM2
GND
Figure 3. Analog-Switch Brightness Control
+18V
TL4242
I
IN
Q
SHDN
TPS7A4533
GND
+3.3V
REF
ST
PWM
GND OUT SENSE
+3.3V
TS3A4742
D
V+
10KΩ
RREFS1
RREFP
NC1
IN1
COM1
NC2
IN2
COM2
Simple Pushbutton 1
GND
Simple Pushbutton 2
.
Primary
Reference Resistor
(RREFP)
Switched
Reference Resistors
(RREFS1 + RREFSwitch)
Equivalent Resistance
(RREF)
Nominal
Output Current
(IOUT)
1W
1 W + 1.4 W = 2.4 W
1.09 W
162 mA
1W
Switch Open
2W
88.5 mA
Texas Instruments 2Q 2010
LED Reference Design Cookbook
38
High-Brightness LED Driver with Single-Clock Operation
➔
TLC5917
NEW!
Description
The TLC5917 is an 8-channel,
constant-current LED driver capable
of up to 120 mA per channel. This
is a great fit when an application
requires a constant LED current
that is independent of input voltage,
temperature and differences in LED
forward-voltage drops resulting from
uncontrolled manufacturing processes.
The outputs can also be tied in parallel
when needed to drive high-brightness
LEDs. Communication is accomplished
through a basic serial port. Many
applications do not have the capability
for generating even simple serial
commands. This reference design
allows a user to overcome this issue
with a simple 555 timer.
The TLC5917 drives eight independent
constant-current sinks. Normally, a
microprocessor drives the /OE (output
enable), SDI (serial data input), CLK
(clock) and LE (latch) pins with four
separate GPIO pins, which allows the
current sink to be independently turned
on and off. If independent LED control
is not needed, the TLC5917 can be
turned on with a single clock signal or
a 555 timer.
• /OE (output enable)—This pin
enables and disables all outputs.
• SDI (serial data input)—The data
clocked into this pin programs each
output to be on or off.
• CLK (clock)—The rising edge of the
clock shifts SDI data into internal
shift registers.
• LE (latch)—The falling edge of LE
latches data from the internal shift
registers into the internal on/off
latches.
Close examination of the TLC5917
timing diagram reveals that a single
PWM signal can replace the CLK and
LE inputs because the rising edge of
CLK shifts data into the IC and the
falling edge of LE latches the data.
Figure 1 shows how to configure the
TLC5917 to operate from a single
clock signal.
/OE must be connected to ground
to enable the IC. The SDI pin can be
connected to VCC to shift 1’s into the
IC to turn all outputs on, and can be
connected to ground to shift all 0’s
into the IC to turn all outputs off. The
CLK and LE pins can be connected to
any type of PWM signal. Turn-on and
turn-off times with this circuit depend
on the clock frequency. At power up,
the TLC5917’s internal on/off latches
that turn each output on or off default
to “0”, so these latches must be set
to “1” before the outputs turn on.
Each rising and falling edge of the
clock signal sequentially turns on each
output, starting with OUT0. Therefore,
it takes eight clock cycles to turn all
LEDs on. Pulling SDI low turns all LEDs
off after eight clock cycles. Figure 2
shows how the TLC5917 responds
to turn-on and turn-off when it is
configured as shown in Figure 1.
Note that Figure 1 shows all the
TLC5917 outputs connected in parallel
to drive a single high-brightness LED.
The TLC5917 outputs can either
drive eight independent LEDs or be
connected in parallel to drive higherpower LEDs. In Figure 1, R3 = 178W,
which sets each output current at
105.3 mA. Connecting all outputs in
parallel yields 105.3 mA x 8 = 842.4
mA of LED current.
This same approach can be used
for any of the 8- and 16-channel
TLC59xx families, including the
TLC5916/25/26/27 and TLC59025.
Web Links
Datasheets, user’s guides, samples:
www.ti.com/sc/device/TLC5917
Figure 1. TLC5917 Driven by 555 Timer
VCC
R1
37.4k
R2
20.0k
C1
1500p
C2
0.1µ
VCC
U1
TLC555D
8 VCC
4
3
RESET OUT
7
DISCH
6
THRES
2
5
TRIG CONT
1
GND
LED Reference Design Cookbook
10kHz Clock
C4
0.1µ
ON/OFF Control
ON/OFF
C3
0.1µ
R3
178
U2
TLC5917PW
16 VDD
3
CLK
4
LE(ED1)
13
(ED2)OE
2
SDI
14
SDO
15
R-EXT
1
GND
OUT0 5
6
OUT1
7
OUT2
8
OUT3
9
OUT4
10
OUT5
11
OUT6
12
OUT7
High Power
LED
Outputs connected
in parallel for 842mA
LED current
Texas Instruments 2Q 2010
High-Brightness LED Driver with Single-Clock Operation
39
TLC5917
➔
Figure 2. LED’s Turn-On and Turn-Off Responses with 10-kHz Clock
For more reference designs, see: www.ti.com/powerreferencedesigns
Texas Instruments 2Q 2010
LED Reference Design Cookbook
40
Wireless-Controlled Triple LED Driver
➔
TPS62260 TPS62260LED
Description
Residential and commercial lighting
can take advantage of the additive
color mixing of red, green and
blue LEDs. This reference design
demonstrates how to remotely manage
the color output of an LED lamp with
a low-power wireless controller. The
color is generated by three LEDs
(red, green and blue). An MSP430™
ultralow-power microcontroller controls
the brightness of each LED with
constant current generated by three
TPS62260 buck converters, one for
each LED.
The color look-up table takes the form
of an array stored in the MSP430.
Whenever the rotary encoder is
turned, new red, green and blue
values are read from the array and
used to generate the three PWM
output signals. Currently 252 values
are stored, which can be changed
if desired. A decimal value of 100
switches the LED off, and a value of
65535 produces a mark-space ratio of
100%. When the 5-V supply is applied,
MSP-FET430UIF tools can be found
respectively at:
the design goes into a demonstration
mode where the values stored in the
array are read and output in sequence
in an infinite loop. As soon as the
rotary encoder is turned, the sequence
stops and a particular fixed color value
can be selected.
http://focus.ti.com/docs/toolsw/
folders/print/ez430-rf2500.html
and
http://focus.ti.com/docs/toolsw/
folders/print/msp-fet430uif.html
There is a pin header that can be
used to plug in the RF board from
the MSP430 Wireless Development
Tool (the eZ430-RF2500), which
is separately available. With this
additional module, the lamp’s colors
can be controlled remotely via the
wireless RF interface.
Key Features
• Wireless RGB color mixing
• Ultra-low-power MSP430 controller
• Wireless development tool available
Web Links
Datasheets, user’s guides, samples:
www.ti.com/sc/device/TPS62260
If a designer prefers to reprogram
the MSP430, a separate MSP430
flash emulation tool can be ordered,
such as the MSP-FET430UIF. More
information on the eZ430-RF2500 and
EVM:
www.ti.com/tps62260led-338
Design Specifications
Parameter
Minimum
Typical
Maximum
Unit
Input voltage
4.5
5
5.5
VDC
Output current
—
0.300
—
Amp
TPS62260LED-338 Schematic
JP1
3.3V
2
4
6
8
10
12
14
1
3
5
7
9
11
13
U1
MSP430F2131RGE
3.3V
R5
47K
JP2
6
5
4
3
2
1
3.3V
eZ430=RF Connector
S1
1
2
3
C3
4
10n
5
6
7
8
9
10
11
12
R4
100K
NC
P2.5/CA5
VSS
VCC
XOUT/P2.7/CA7
TEST
XIN/P2.6/CA6
P1.7/TA2/TDO/TDI
NM /RST
P1.6/TA1/TDI/TCLK
P2.0/ACLK/CA2
NC
P2.1/INCLK/CA3
P1.5/TA0/TMS
P2.2/CAOUT/TA0/C44P1.4/SMCLK/TCK
NC
P1.3/TA2
P2.3/TA1/CA0
P1.3/TA1
P2.4/TA2.CA1
P1.1/TA0
NC
P1.0/TACLK
PwPd
R3
100K
3.3V
24
23
22
21
20
19
18
17
16
15
14
13
C2
100n
NET-DIMM_LED1
NET-DIMM_LED2
NET-DIMM_LED3
NET-EN
R6
100K
For more reference designs, see: www.ti.com/powerreferencedesigns
LED Reference Design Cookbook
Texas Instruments 2Q 2010
Wireless-Controlled Triple LED Driver
41
TPS62260 TPS62260LED
➔
Red LED
Blue LED
U11
TPS62260DRV
C13
4.7µF
R13
10K
TP31
red
L11
1
6
1
GND SW
5
2
VIN MODE
4
3
EN
FB
PwPd
???mV
7
NET-EN
VIN +5V
C12
22µF
TP12
C11
4.7µF
R11
10K
D13
D14
VIN +5V
C32
22µF
C33
4.7µF
TP32
L31
6
1
GND SW
5
2
VIN MODE
4
3
EN
FB
PwPd
???mV
7
NET-EN
R12
2 <1206>
R33
10K
TP13
D33
blue
1
TP11
U31
TPS62260DRV
C31
4.7µF
R31
10K
R32
2 <1206>
TP33
NET-DIMM_LED1
TS4148RY
D34
NET-DIMM_LED3
TS4148RY
Green LED
U21
TPS62260DRV
L21
6
1
GND SW
5
2
VIN MODE
4
3
EN
FB
PwPd
???mV
7
NET-EN
VIN +5V
C22
22µF
TP22
C23
4.7µF
R23
10K
D23
green
1
TP21
C21
4.7µF
R21
10K
D24
R22
2 <1206>
TP23
NET-DIMM_LED2
TS4148RY
VINmax < 6V
J1
+5V
1
2
3
R2
330
C4
22µF
Texas Instruments 2Q 2010
3.3V
D1
BZX84-C3V3
C1
4.7µF
LED Reference Design Cookbook
42
Low-Voltage Buck Boost for LED Torch
➔
TPS63000 PMP3038
Description
Key Features
• Buck-boost converter topology
• Ideal for battery applications
• 1.8-A output capability
• Auto buck- boost mode switching
• Dual LED brightness levels
• Operates down to 1.2 V
of two or three cells in series that have
a maximum voltage of 5 V. During
operation, the VBAT drops below the
Vf of the LED, and the TPS63000
automatically switches from buck
mode to boost mode to create the
constant current needed for the
LED. The TPS63000 can boost from
voltages as low as 1.2 V. A switch that
brings R4 into or out of the feedback
loop provides a dimming mechanism
for the flashlight to toggle between 300 and 600 mA.
The TPS63000 provides a powersupply solution for products that
use a two- or three-cell alkaline,
NiCd or NiMH battery, or a one-cell
Li-Ion or Li-Polymer battery. The
buck-boost converter is based on
a fixed-frequency PWM controller
that uses synchronous rectification
to obtain maximum efficiency. The
maximum average current in the
switches is limited to a typical value
of 1800 mA, and the converter can
be disabled to minimize battery
drain. During shutdown, the load
is disconnected from the battery.
The device is packaged in a 10-pin
QFN PowerPAD™ (DRC) package
measuring 3 x 3-mm.
The PMP3038 circuit was designed
for a torch or rugged flashlight. Most
torch applications still use alkaline
batteries with a common configuration
Web Links
Datasheets, user’s guides, samples:
www.ti.com/sc/device/TPS63000
Design Specifications
Parameter
Minimum
Maximum
Unit
Input voltage
1.2
5
VDC
Output voltage
­—
5
Volts
Output current
300
600
mAmp
Switch frequency
­—
1.5
MHz
PMP3038 Schematic
L1
2.2µH
S1
NO
NC
4
5
8
+
1.5V x 2
BAT
C3
10µF
7
6
U1
TPS63000DRC
L1
L2
VIN
VOUT
VINA
PGND
SYNC/PS
EN1
PwPd
11
FB
GND
2
1
3
10
THERMALPAD
C6
DNP
9
R2
49.9K
C4
1000pF
D1
7090 XR-E
R1
10K
C1
22µF
D2
LM4040D
2.048V
C2
22µF
R3
0.3
R4
0.3
NO
NC
R5
12.7K
S2
R6
49.9
For more reference designs, see: www.ti.com/powerreferencedesigns
LED Reference Design Cookbook
Texas Instruments 2Q 2010
Low-Voltage Buck Boost for LED Torch
43
TPS63000 PMP3038
➔
Output Current Graphs with DC Coupling
Control Loop Response Graphs
Control loop response with 0.63 A.
Output current with VIN = 3 V.
Control loop response with 0.32 A.
Output current with VIN = 4 V.
Efficiency Curve for IO = 0.32 A and IO = 0.62 A
Turn On with 0.63 A
Efficiency.
Texas Instruments 2Q 2010
LED Reference Design Cookbook
44
Boost Driver with Integrated Power Switch
➔
TPS61500
Description
Key Features
• Supports boost topology
• Integrated 3-A 40-V power switch
• Supports PWM or AM dimming
• Protection features:
• Pulse by pulse
• Thermal shutdown
IC for pure PWM dimming, with the
average LED current being the PWM
signal’s duty cycle times a set LED
current.
The TPS61500 is a monolithic
switching regulator with an integrated
3-A, 40-V power switch. It is an ideal
driver for high-brightness 1- or 3-W
LEDs. The device has a wide inputvoltage range to support applications
with input voltage from multicell
batteries or regulated 5-V to12-V power rails.
The device features a programmable
soft-start function to limit inrush
current during start-up and has other
protection features built in, such as
pulse-by-pulse overcurrent limiting,
overvoltage protection and thermal
shutdown. The TPS61500 is available
in a 14-pin HTSSOP package with
PowerPAD™.
The LED current is set with an external
sense resistor, R3, and with feedback
voltage that is regulated to 200 mV by
a current-mode PWM control loop, as
shown in the schematic below. The
device supports analog and pure PWM
dimming methods for LED brightness
control. Connecting a capacitor to
the DIMC pin configures the device to
be used for analog dimming, and the
LED current varies in proportion to the
duty cycle of an external PWM signal.
Floating the DIMC pin configures the
Web Links
Datasheets, user’s guides, samples:
www.ti.com/sc/device/TPS61500
LED Current vs. Input Supply and LED Number
Input Supply
5V
12 V
LED number 4
1000 mA
2000 mA
LED number 6
600 mA
1200 mA
LED number 8
450 mA
1000 mA
Note: Assumption that LED forward voltage is 3.5V, and TPS61500’s conversion efficiency is 85%.
Typical Application Schematic
VIN 5V
L1
D1
C1
TPS61500
PWM
VIN
SW
EN
SW
COMP
C4
C5
R4
C3
OVP
DIMC
FB
FREQ
PGND
S3
PGND
AGND
PGND
R1
DL1
3W LED
C2
DL2
R2
DL3
DL4
R3
For more reference designs, see: www.ti.com/powerreferencedesigns
LED Reference Design Cookbook
Texas Instruments 2Q 2010
Boost Driver with Integrated Power Switch
45
TPS61500
➔
Efficiency vs. Output Current
PWM Dimming Application Circuit: Circuit for the TPS61500 to Perform Analog Dimming Using an Injected Analog Signal
VIN 5V
L1
DL1
3W LED
C1
ON
VIN
PWM
SW
COMP
C4
C5
≥100nF
R4
C3
DL2
SW
EN
0 - 1.229V
DAC
R1
TPS61500
OFF
DSP or
µcontroller
D1
DIMC
FB
FREQ
PGND
SS
PGND
AGND
PGND
DL3
R2
OVP
DL4
R3
Analog Dimming by External DAC: Pure PWM Dimming Method
VIN 5V
L1
D1
TPS61500
VIN
PWM
EN
COMP
C4
Texas Instruments 2Q 2010
DL1
3W LED
R1
C1
R4
Q2
C3
R1
C2
SW
DL2
R2
SW
OVP
DIMC
FB
FREQ
PGND
SS
PGND
AGND
PGND
DL3
R2
PWM
Q1
DL4
R3
LED Reference Design Cookbook
46
1.5-A White LED Driver for Notebooks
➔
TPS61180/1/2
NEW!
Description
overvoltage protection, soft starting
and thermal shutdown.
across wide dimming-duty-cycle and
frequency ranges, therefore reducing
the audible noise.
The TPS61180/1/2 ICs provide highly
integrated solutions for media-size
LCD backlighting. These devices
have a built-in, high-efficiency boost
regulator with an integrated 1.5-A/40-V
power MOSFET. The six current-sink
regulators provide high-precision
current regulation and matching. In
total, the device can support up to 60
white LEDs (WLEDs). In addition, the
boost output automatically adjusts its
voltage to the WLED forward voltage
to improve efficiency.
Datasheets, user’s guides, samples:
www.ti.com/sc/device/TPS61180,
www.ti.com/sc/device/TPS61181 or
www.ti.com/sc/device/TPS61182
Parameter
Minimum
Typical
Maximum
Unit
Input voltage
4.7
—
24
Volts
Output voltage
15
—
38
Volts
Output ripple
—
—
200
mVPP
Output current
0
—
150
mA
Switching frequency
—
1000
—
kHz
Switch
Channels
Current per Channel
LEDs per Channel
TPS61183
2.0 A
6
30 mA
Up to 10
TPS61185
2.0 A
8
25 mA
Up to 10
TPS61195
2.5 A
8
30 mA
Up to 12
Also Available Soon
Device
Preview products are listed in bold blue.
Typical Application Schematic
Optional
5V to 24V
L1
10µH
D1
Q1
R2
51Ω
Web Links
Design Specifications
The devices support pulse-widthmodulation (PWM) brightness
dimming. During dimming, the WLED
current is turned on/off at the duty
cycle, and frequency is determined
by the PWM signal input on the
DCTRL pin. One potential issue of
PWM dimming is audible noise from
the output ceramic capacitors. The
TPS61180/1/2 family is designed
to minimize this output AC ripple
C1
4.7µF
The TPS61180 IC requires an external
3.3-V IC supply, while the TPS61181/2
ICs have a built-in linear regulator for
the IC supply. All the devices are in a 3- x 3-mm QFN package.
The TPS61180/1/2 ICs provide a driver
output for an external PFET connected
between the input and inductor. During
short-circuit or overcurrent conditions,
the ICs turn off the external PFET
and disconnect the battery from the
WLEDs. The PFET is also turned off
during IC shutdown (true shutdown)
to prevent any leakage current from
the battery. The device also integrates
C2
4.7µF
10 WLED in series, 120mA Total
R3
100kΩ
Fault
SW
VBAT
C3
1µF
VO
TPS61181/2
CIN
C4
0.1µF
IFB1
IFB2
IFB3
IFB4
IFB5
EN
EN
DCTRL
PWM Dimming
ISET
IFB6
PGND
GND
R1
62kΩ
LED Reference Design Cookbook
Texas Instruments 2Q 2010
1.5-A White LED Driver for Notebooks
47
TPS61180/1/2
➔
Switching Waveforms
Efficiency vs. PWM Duty
Output Ripple at PWM Dimming
Output Ripple at PWM Dimming
Start-up Waveforms
Output Current vs. Dimming Duty Cycle
Texas Instruments 2Q 2010
LED Reference Design Cookbook
48
Multichannel PWM Power Driver for Power LED Applications
➔
DRV9812
NEW!
Description
The DRV9812, which has a wide
input voltage of up to 50 V, is a
synchronous multichannel PWM power
driver for LED applications. It can be
configured as buck, boost or buck/
boost, depending on the application
requirements, and can drive 4
independent LED strings with up to
15 power LEDs in series per string. It
can also provide DC, sine-wave, or
any other kind of desired current to
drive LEDs based on a PWM control
algorithm from an external MCU
controller.
Because of the integrated low-RDS(on)
MOSFETs and intelligent gate-drive
design, the efficiency of the DRV9812
can be as high as 96%. The device
offers integrated, on-chip safeguards
against a wide range of fault conditions
such as short circuits and overcurrent
and undervoltage conditions. It
also offers integrated two-stage
thermal protection. A programmable
overcurrent detector provides an
adjustable cycle-by-cycle current limit
to meet different power requirements.
The DRV9812 has a unique,
independent supply pin for each
channel, enabling it to support multiple
outputs with different power-supplyvoltage requirements or with mixed
converter topologies.
Web Links
Datasheets, user’s guides, samples:
www.ti.com/sc/device/DRV9812
Design Specifications
Parameter
Minimum
Typical
Maximum
Input Voltage (V)
2
—
50
Output Voltage (V)
0
—
49.5
11.4
12.3
13.2
Peak Output Current (A)
—
—
5
RMS Output Current (A)
—
—
2.5
Switching Frequency (kHz)
—
10 to 500
1000
Gate Voltage (V)
DRV9812 Typical Application Schematic in Buck Configuration
VIN
Up to 50V
VDD
GVDD_D
RESET_CD
GVDD_C
GVDD_A
RESET_AB
GVDD_B
12V
PWM_A
PWM
DH_C
PWM_B
DH_D
PWM_C
BST_A
PWM_D
DL_A
DL_B
OTW
BST_C
OC_ADJ
DL_C
BST_D
DL_D
GND_D
GND_C
GND_B
GND_A
GND
M3
AGND
M1
M2
ADC
VLED
BST_B
DRV9812
FAULT
Real-Time MCU
(TMS320F2802x/3x,
C2000™, etc.)
DH_A
DH_B
VREG
AMP
AMP
AMP
AMP
For more reference designs, see: www.ti.com/powerreferencedesigns
LED Reference Design Cookbook
Texas Instruments 2Q 2010
Multichannel PWM Power Driver for Power LED Applications
49
DRV9812
➔
DRV9812 Typical Application Schematic in Boost Configuration
VDD
GVDD_D
RESET_CD
GVDD_C
GVDD_A
RESET_AB
GVDD_B
12V
DH_B
PWM_A
PWM
DH_C
PWM_B
DH_D
PWM_C
BST_A
DL_A
PWM_D
BST_B
DRV9812
FAULT
DL_B
OTW
BST_C
OC_ADJ
DL_C
BST_D
DL_D
GND_D
GND_C
GND_B
M3
GND_A
M2
GND
M1
AGND
Real-Time MCU
(TMS320F2802x/3x,
C2000™, etc.)
VLED
Up to 50V
DH_A
VREG
VIN
AMP
AMP
AMP
AMP
ADC
PWM Linearity Curve
Texas Instruments 2Q 2010
Efficiency Curve
LED Reference Design Cookbook
50
Small LCD Backlight with Digital and PWM Dimming
➔
TPS61160/1
Description
With a 40-V integrated switch FET, the
TPS61160/1 is a boost converter that
drives up to 10 LEDs in series. The
boost converter, which allows for the
use of high-brightness LEDs in general
lighting, runs at a fixed frequency of
1.2 MHz with a 0.7-A switch-current
limit.
As shown in the schematic below
of a typical application, the default
white-LED (WLED) current is set with
the external sense resistor, RSET, and
the feedback voltage is regulated
to 200 mV. The LED current can be
controlled via the one-wire digital
interface (EasyScale™ protocol)
through the CTRL pin. Alternatively,
a PWM signal can be applied to the
Key Features
• Efficient boost topology
• Integrated 40-V power switch
• Drives up to 10 LEDs
• PWM dimmable
• 200-mV VREF
• No audible noise
CTRL pin such that the duty cycle
determines the feedback reference
voltage. In either digital or PWM mode,
the TPS61160/1 does not provide LED
current in burst; therefore, it does not
generate audible noise on the output
capacitor. For protection during openLED conditions, the TPS61160/1 has
integrated circuitry to prevent the
output from exceeding the absolute
maximum ratings.
Web Links
Datasheets, user’s guides, samples:
www.ti.com/sc/device/TPS61160
Ordering Information1
TA
Open LED Protection (typical)
Package2
Package Marking
26 V
TPS61160DRV
BZQ
38 V
TPS61161DRV
BZR
–40°C to 85°C
1
For most current package and ordering information: www.ti.com/sc/device/TPS61160.
2
The DRV package is available in tape and reel. Add R suffix (TPR61160DRVR) to order quantities of 3,000 parts per reel or add T suffix
(TPS61160DRVT) to order 250 parts per reel.
Typical Application Schematic
L1
22µH
VI 3V to 18V
C1
1µF
D1
C2
1µF
TPS61161
On/Off
Dimming
Control
VIN
SW
CTRL
FB
COMP
C3
220nF
L1: TDK VLCF5020T-220MR75-1
C1: Murata GRM188R61E105K
C2: Murata GRM21BR71H105K
D1: ONsemi MBR0540T1
GND
Rset
R10Ω
20mA
For more reference designs, see: www.ti.com/powerreferencedesigns
LED Reference Design Cookbook
Texas Instruments 2Q 2010
Small LCD Backlight with Digital and PWM Dimming
51
TPS61160/1
➔
Efficiency vs. Output Current
PWM Dimming Linearity: FB Voltage vs. PWM Duty Cycle
PWM Dimming Output Ripple
Texas Instruments 2Q 2010
LED Reference Design Cookbook
52
Small LCD Backlight from LDO
➔
TPS7510x
Description
The TPS7510x linear low-dropout
(LDO) LED current source is optimized
for low-power LED backlighting
applications such as keypads and
navigation pads. The device provides
a constant current for up to four
unmatched LEDs organized in two
banks of two LEDs each in a commoncathode topology. Without an external
resistor, the current source defaults
to the factory-programmable, preset
current level with ±0.5% accuracy
(typical). An optional external resistor
can be used to set initial brightness to
user-programmable values with higher
accuracy. Brightness can be varied
from off to full brightness by inputting a PWM signal on each enable pin.
Each bank has independent enable
and brightness control, but the
currents of all four channels are
matched concurrently. The inputsupply range is ideally suited for
single-cell Li-Ion battery supplies, and
the TPS7510x can provide up to 25 mA
per LED. No internal switching signals
are used, eliminating troublesome
electromagnetic interference (EMI). The
TPS7510x is offered in an ultra-small,
9-ball, 0.4-mm ball-pitch wafer chipscale package (WCSP) and a 2.5 x
2.5-mm, 10-pin SON package, yielding
a very compact total solution size
ideal for mobile handsets and portable
backlighting applications.
Figure 2 shows the TPS75105
efficiency data for several different
WLED forward voltages over the Li-Ion
battery’s range. The LED efficiency for the TPS75105 is comparable to or better than that of other WLEDdriver solutions.
At first glance, using a linear LDO
circuit to drive LEDs may seem
impractical, given the linear regulator’s
reputation for low efficiency. However,
the efficiency of LDOs is often
misunderstood. LDO efficiency is
entirely based on the input/outputvoltage ratio; therefore, the efficiency
of driving white LEDs (WLEDs) can
be quite high. For example, driving a
3-V WLED from a 3.6-V Li-Ion-battery
input translates into an LED efficiency
of 83%.
Figure 3 demonstrates the LED
efficiency of the TPS7510x over the
Li-Ion battery’s discharge curve.
The average efficiency for the entire
discharge range is over 80% for all
three curves, and up to 90% when
VLED = 3.3 V.
Figure 1 shows a typical application for
the TPS75105. Note that this device
requires no external components to
drive the WLEDs. The total solution is
extremely small and very cost effective.
Key Features
• Drives four constant current outputs
• PWM dimmable
• 0.5% current accuracy
• 25 mA per LED
• Ultra-small size ball pitch packaging
83% efficient solution
Web Links
Datasheets, user’s guides, samples:
www.ti.com/sc/device/TPS75105
Device Specifications
Device
TPS7510x
VIN
LEDs
∆IDX MAX
2.5 V to 5.5 V
2 mm x 2 mm
25 mA
VDO
∆IDX
Packages
28 mV
±2%
WCSP, DSK
TPS7510x Package Options
For more reference designs, see: www.ti.com/powerreferencedesigns
LED Reference Design Cookbook
Texas Instruments 2Q 2010
Small LCD Backlight from LDO
53
TPS7510x
➔
Figure 1 - Typical Application
ON
ENA
OFF
ON
OFF
3.6V
Battery
Optional
VIN
D1A
ENB
D2A
ISET
D1B
GND
D2B
Figure 2 - Efficiency Data
Figure 3 - LED Efficiency
Texas Instruments 2Q 2010
LED Reference Design Cookbook
54
Medium-Size LCD Backlight
➔
TPS61165
Description
With a 40-V integrated switch FET, the
TPS61165 is a boost converter that
drives up to ten LEDs in series. The
boost converter, which allows for the
use of high-brightness LEDs in general
lighting, runs at a fixed frequency of
1.2 MHz with a 1.2-A switch-current
limit.
As shown in the schematic below
of a typical application, the default
white-LED (WLED) current is set with
the external sense resistor, RSET, and
the feedback voltage is regulated
to 200 mV. The LED current can be
controlled via the one-wire digital
interface (EasyScale™ protocol)
through the CTRL pin. Alternatively,
a PWM signal can be applied to the
CTRL pin such that the duty cycle
determines the feedback reference
voltage. In either digital or PWM mode,
the TPS61160/1 does not provide LED
current in burst; therefore, it does not
generate audible noise on the output
capacitor. For protection during openLED conditions, the TPS61165 has
integrated circuitry to prevent the
output from exceeding the absolute
maximum ratings.
The TPS61165 is available in a spacesaving, 2 x 2-mm QFN package with a thermal pad.
Key Features
• Boost converter for high efficiency
• 40-V integrated power switch
• Drives up to 10 LEDs
• Low Vref for high efficiency
• One wire digital interface
• PWM dimming
• No audible noise
Web Links
Datasheets, user’s guides, samples:
www.ti.com/sc/device/TPS61165
LED Current vs. Input Supply and LED Number
Input Supply
3V
5V
12 V
LED number 3
200 mA
350 mA
820 mA
LED number 6
100 mA
175 mA
410 mA
LED number 8
70 mA
120 mA
300 mA
Note: Assumption that LED forward voltage is 3.5 V, and TPS61165’s conversion efficiency is 80%.
Typical Application Schematic
L1
10µH
VIN 5V
C1
1µF
D1
C2
1µF
TPS61165
VIN
On/Off
Dimming
Control
CTRL
COMP
C3
220nF
SW
350mA
FB
GND
Rset
R57Ω
L1: TOKO #A915_Y-100M
C1: Murata GRM188R61A475K
C2: Murata GRM188R61E105K
D1: OSRAM LW-W 5SM
For more reference designs, see: www.ti.com/powerreferencedesigns
LED Reference Design Cookbook
Texas Instruments 2Q 2010
55
TPS61165
➔
Efficiency vs. Output Current
Medium-Size LCD Backlight
Startup
PWM Dimming Linearity: FB Voltage vs. PWM Duty Cycle
PWM Dimming Output Ripple
Texas Instruments 2Q 2010
LED Reference Design Cookbook
56
Large-LCD Backlight Driver
➔
TPS61195
Description
Key Features
• Boost regulator with integrated 3-A
50-V power switch
• Eight current-sink regulators for
precision intensity control
• High efficiency through automatic
VOUT to LED Vforward
• PWM dimming
• Multiple protection features:
• Overcurrent
• Short circuit
• Over temperature
dimming to be added when the analog
signal keeps the WLED current down
to 12.5%. Below 12.5%, the analog
signal will be translated into PWM
duty-cycle information to control the
on/off of the WLED current and to average the WLED current down to 1%.
The TPS61195 provides highly
integrated solutions for large-LCD
backlights. This device has a builtin, high-efficiency boost regulator
with an integrated 2.5-A, 50-V power
MOSFET. The eight current-sink
regulators provide high-precision
current regulation and matching. In
total, the device can support up to 96
white LEDs (WLEDs). In addition, the
boost output automatically adjusts its
voltage to the WLED forward voltage
to improve efficiency.
The TPS61195 integrates overcurrent
protection, short-circuit protection,
soft start and overtemperature
shutdown. The device also provides
programmable output overvoltage
protection, and the threshold is
adjusted by an external resistor/divider
combination.
The TPS61195 supports multiple
brightness-dimming methods. During
direct PWM dimming, the WLED
current is turned on/off at the duty
cycle, and the frequency is determined
by an integrated PWM signal. In PWMdimming mode, the frequency of this
signal is resistor-programmable, while
the duty cycle is controlled from an
external PWM signal input from a PWM
pin. In analog mixed dimming modes,
the input PWM duty-cycle information
is translated into an analog signal
to control the WLED current signal
linearly over a brightness area of 12.5
to 100%. The device also allows PWM
Web Links
Reference designs:
www.ti.com/powerreferencedesigns
Datasheets, user’s guides, samples:
www.ti.com/sc/device/TPS61195
The TPS61195 has a built-in linear
regulator for the IC supply and is
available in a 4 x 4-mm QFN package.
LED Current vs. Input Supply and LED
Number
Parameter
Minimum
Maximum
Unit
Input voltage
4.0
24
Volts
Output voltage
16
48
Volts
Number of channel
—
8
—
Output current
0
0.32
Amp
600 KHz
1 MHz
—
Switching frequency
TPS61195 Schematic
L1
10µH
4v ~ 24V
D1
C3
1µF
C1
4.7µF
VIN
C2
0.1µF
VIN
VDDIO
SEL
Dimming
Interface
Mode
OVP
FDIM
R3
523KΩ
TPS61195
PWM
SMBus
Open
D-PWM
PWM
SEL
GND
PWM
PWM
ISET
R*
Mix Mode
PWM
R1
65KΩ
R4
953KΩ
FSW
VDDIO
IFB1
IFB2
IFB3
IFB4
IFB5
IFB6
IFB7
IFB8
* 510Kohms resistance to ground.
SDA
SCL
LED Reference Design Cookbook
R6
46.4KΩ
VIN
DPWM
FDPWM
R2
40KΩ
R5
1M
PGND1
PGND2
EN
200 Hz
Up to 48V
AGND
Texas Instruments 2Q 2010
Large-LCD Backlight Driver
57
TPS61195
➔
Dimming Efficiency VIN = 10.8 V; 9s8p
Mixed Mode Dimming Waveform: 20% Brightness—
Pure Analog
PWM Dimming Current Linearity VIN = 10.8 V
Mixed Mode Dimming Waveform: 8% Brightness Mode
Mix Mode Dimming Current Linearity VIN = 10.8 V
Texas Instruments 2Q 2010
LED Reference Design Cookbook
58
24-Channel, 12-Bit PWM LED Driver
➔
TLC5951
NEW!
Description
The TLC5951 is a 24-channel,
constant-current sink driver. Each
channel has an individually adjustable,
4096-step, pulse-width-modulation
(PWM) grayscale (GS) brightness
control (BC) and 128-step constantcurrent dot correction (DC). The DC
adjusts brightness deviation between
channels and other LED drivers. The
output channels are grouped into
three groups of eight channels. Each
channel group has a 256-step global
BC function and an individual GS clock
input.
GS, DC and BC data are accessible via a serial-interface port. DC and BC
can be programmed via a dedicated
Web Links
serial-interface port. The TLC5951 has
three error-detection circuits: LED open
detection (LOD), LED short detection
(LSD) and a thermal-error flag (TEF).
LOD detects a broken or disconnected
LED, LSD detects a shorted LED, and
TEF indicates an overtemperature
condition.
Datasheets, user’s guides, samples:
www.ti.com/sc/device/TLC5951
Design Specifications
Parameter
Test Conditions
Minimum
Typical
Maximum
Unit
Input voltage
—
3.0
—
5.5
Volts
Output Voltage
OUTR/G/B 0 to 7
­3.0
—
17
Volts
Dot correction/global
brightness control
—
—
7/8
—
Bits
Output current
—
35
40
45
mA
Grayscale clock frequency
—
—
—
33
MHz
Typical Application Schematic (used when DCSIN/DCSCK Ports are used)
VLED
≈
VLED
GND
GND
≈
READ DATA
OUTR0/G0/B0
DC/BC/FC
Controller
DCSCK
DCSOUT
GSSIN
GSLAT
TLC5951
IC1
GSSOUT
GSSCK
GSSIN
GSLAT
XBLNK
GSCKG
GSCKB
GSSOUT
XBLNK
VCC
GSCKR
GSCKG
TLC5951
ICn
GSLAT
XBLNK
GSCKR
DCSOUT
DCSCK
≈
GSSCK
GSSCK
OUTR7/G7/B7
DCSIN
DCSCK
GSSIN
GS
Controller
DCSIN
OUTR0/G0/B0
≈
GSSIN
DCSIN
OUTR7/G7/B7
VCC
GSCKR
GSCKG
VCC
GSCKB
VCC
GSCKB
IREF
IREF
GND
GND
GND
RIREF
GND
GND
6
≈≈≈
READ DATA
GND
RIREF
For more reference designs, see: www.ti.com/powerreferencedesigns
LED Reference Design Cookbook
Texas Instruments 2Q 2010
24-Channel, 12-Bit PWM LED Driver
59
TLC5951
➔
Output Current vs. Output Voltage
Dot-Correction (DC) Linearity (IOLCMax with Lower Range)
Constant-Current Error vs. Ambient Temperature
(Channel-to-Channel, Red Group)
Global-Brightness-Control (BC) Linearity
(IOLCMax with Upper Range)
Dot-Correction (DC) Linearity (IOLCMax with Upper Range)
Constant-Current Output-Voltage Waveforms (Red Group)
Texas Instruments 2Q 2010
LED Reference Design Cookbook
60
24-Channel, Constant-Current LED Driver
➔
TLC5952 with Global Brightness Control
Description
NEW!
Web Links
thermal-error flag (TEF). The error
detection is read via a serial interface.
LOD detects a broken or disconnected
LED, LSD detects a shorted LED, and
TEF indicates an overtemperature
condition.
The TLC5952 is a 24-channel,
constant-current sink driver. Each
channel can be turned on/off with
internal register data. The output
channels are grouped into three
groups of eight channels each. Each
channel group has a 128-step globalbrightness-control (BC) function.
Datasheets, user’s guides, samples:
www.ti.com/sc/device/TLC5952
Design Specifications
Parameter
Both on/off data and BC are writable
via a serial interface. The maximum
current value of all 24 channels is
set by a single external resistor. The
TLC5952 has three error-detection
circuits: LED open detection (LOD),
LED short detection (LSD) and a
Test Conditions
Input voltage
Minimum
Typical
Maximum
Unit
—
3.0
—
5.5
Volts
OUTR/G/B 0 to 7
3.0
—
17
Volts
Global brightness control
—
—
7
—
Bits
Output current
—
29
32
35
mA
Data shift clock frequency
—
—
—
35
MHz
Output Volatage
Typical Application Schematic
VLED
≈
+
OUTB7
OUTR0
SIN
SCLK
OUTR0
SOUT
SCLK
LAT
LAT
BLANK
BLANK
≈
DATA
TLC5952
IC1
OUTB7
SIN
SOUT
SCLK
VCC
LAT
VCC
BLANK
GND
TLC5952
ICn
VCC
VCC
GND
Controller
IREF
IREF
RIREF
3
≈ ≈
ERROR
READ
RIREF
For more reference designs, see: www.ti.com/powerreferencedesigns
LED Reference Design Cookbook
Texas Instruments 2Q 2010
24-Channel, Constant-Current LED Driver
61
TLC5952 with Global Brightness Control
➔
Output Current vs. Output Voltage (Red and Green Groups)
Constant-Current Error vs. Output Current
(Channel-to-Channel, Red Group)
Output Current vs. Output Voltage (Blue Group)
Global Brightness-Control (BC) Linearity
(Red and Green Groups)
Constant-Current Error vs. Ambient Temperature
(Channel-to-Channel, Red Group)
Constant-Current Output-Voltage Waveforms (red group)
Texas Instruments 2Q 2010
LED Reference Design Cookbook
62
16-Channel LED Driver with Load-Switch Dimming Control
➔
TLC59116
NEW!
Description
The TLC59116 is a 16-channel,
constant-current LED driver capable
of sinking up to 100 mA per channel.
External current (IOUT) is programmed
by an external resistor (REXT). The
device has a serial I2C interface and
multiple functions, some of which
allow individual pin blinking and global
brightness control. Internal brightness
and blinking are accomplished by
using the TLC59116’s internal oscillator
to create digital dimming, commonly
referred to as pulse-width-modulation
(PWM) dimming. The TLC59116 also
has an internal register that can be
set to change the brightness “gain”
from 99.2% (the default) to 8.3%. This
reference design allows any of these
options to be used but also has an
added load switch for manipulating
the REXT to change brightness. This
method can also be used to produce
blinking between different brightness
levels, which cannot be achieved with
the TLC59116 alone.
LED brightness can be programmed
to change depending on the time of
day or the level of ambient light. LED
dimming can be accomplished through
analog or digital methods. In analog
dimming, the current through the LED
is reduced. In digital (PWM) dimming,
the LED is turned on and off at a high
frequency. The human eye integrates
the on and off brightness in such a way
that the LED appears to dim. Changing
the frequency and duty cycle of the
PWM signal will impact the brightness.
For example, an LED application that
requires 40 mA to be at full brightness
will be at 50% brightness if the analog
dimming is set for a drive current of
20 mA or if the PWM operates at a
50% duty cycle. Figure 1 shows the
difference between analog and PWM
dimming.
For the TLC59116 LED driver, IOUT
is set by the relationship between the
external resistor and the REXT pin’s
reference voltage (VREXT), as shown in
equation 1.
(1) IOUT = VREXT/REXT x 15
Equation 2 solves for REXT.
(2) REXT = VREXT/IOUT x 15
The default VEXT value is 1.25 V. The
actual value is dependent on the
brightness “gain” set by the user via
the TLC59116’s internal register. As a
result, any manipulation of the current
based on REXT is still dependent on
the gain.
which is higher than the 0.9 V required
for operation.
The TPS22901’s default is “on”
and its resistor is used to compute
IOUT, resulting in 80 mA. When the
TPS22901 is off (the switch is open),
the resulting current changes to 40
mA. The host MSP430 controller can
easily control the frequency of the dim/
full-brightness timing. The TPS22900
(dual load switch) can provide up to
four brightness levels.
Web Links
Datasheets, user’s guides, samples:
www.ti.com/sc/device/TLC59116
Changing REXT changes the resulting
current. For example, if IOUT was set to
80 mA, REXT would be
(3) REXT = 1.25 V/80 mA x 15 = 234.
Similarly, a 40-mA current would result
in an REXT of 468 W.
Figure 2 shows a basic configuration
for an LED application that requires
40 mA per channel. The 5-V supply
is stepped down to 3.3 V by a simple
LDO to drive the MSP430™ controller
and the TLC59116 LED driver. The 5-V
supply powers the LEDs directly.
Brightness control is enabled by
adding a resistor in parallel with REXT.
Adding another 468-W resistor allows
IOUT to be doubled from 40 mA to
80 mA. Using an available GPIO line
from the MSP430 to the load switch
allows the designer to add or remove
the extra resistor as desired. Figure 3
shows a simple implementation using
a TPS22901 load switch.
The TPS22901 load switch fits this
dimming-control application because
the RON is below 100 mW (negligible in
series with 468 W) and VREXT is 1.25 V,
For more reference designs, see: www.ti.com/powerreferencedesigns
LED Reference Design Cookbook
Texas Instruments 2Q 2010
16-Channel LED Driver with Load-Switch Dimming Control
63
TLC59116
➔
Figure 1. Analog vs. PWM Dimming
Figure 2. Programmable LED Driver
+5V
IN
SHDN
TPS7A4533
GND
+3.3V
SENSE
OUT
+3.3V
VDD
SDA
SDA
OUT15
RESET
RESET
OUT14
MSP430
TLC59116
SCL
SCL
A0-A3
ON
OUT13
OUT1
OUT0
REXT
GND
REXT2
468Ω
Figure 3. Analog Dimming/Blinking with a Load Switch
+5V
IN
SHDN
TPS7A4533
GND
+3.3V
SENSE
OUT
SCL
SCL
VDD
SDA
SDA
OUT15
RESET
RESET
OUT14
A0-A3
ON
TPS22901
TLC59116
MSP430
+3.3V
VIN
GND
VOUT
REXT2
468Ω
Texas Instruments 2Q 2010
OUT13
OUT1
OUT0
REXT
ON
ON = 234Ω = 80mA
OFF = 468Ω = 40mA
GND
REXT2
468Ω
LED Reference Design Cookbook
TI Worldwide Technical Support
Internet
TI Semiconductor Product Information Center
Home Page
support.ti.com
TI E2E™ Community Home Page
e2e.ti.com
Product Information Centers
Americas Phone
+1(972) 644-5580
Brazil
Phone
0800-891-2616
Mexico
Phone
0800-670-7544
Fax
Internet/Email
+1(972) 927-6377
support.ti.com/sc/pic/americas.htm
Europe, Middle East, and Africa
Phone
European Free Call
International
Russian Support
00800-ASK-TEXAS
(00800 275 83927)
+49 (0) 8161 80 2121
+7 (4) 95 98 10 701
Note: The European Free Call (Toll Free) number is not active
in all countries. If you have technical difficulty calling the free
call number, please use the international number above.
Fax
Internet
+(49) (0) 8161 80 2045
support.ti.com/sc/pic/euro.htm
Japan
Phone
Fax
Domestic
International
Domestic
0120-92-3326
+81-3-3344-5317
0120-81-0036
Internet/Email International
Domestic
support.ti.com/sc/pic/japan.htm
www.tij.co.jp/pic
Asia
Phone
International
+91-80-41381665
Domestic
Toll-Free Number
Australia
1-800-999-084
China
800-820-8682
800-96-5941
Hong Kong
India
1-800-425-7888
Indonesia
001-803-8861-1006
Korea
080-551-2804
Malaysia
1-800-80-3973
0800-446-934
New Zealand
Philippines
1-800-765-7404
Singapore
800-886-1028
Taiwan
0800-006800
Thailand
001-800-886-0010
Fax
+886-2-2378-6808
Email
[email protected] or [email protected]
Internet
support.ti.com/sc/pic/asia.htm
Important Notice: The products and services of Texas Instruments
Incorporated and its subsidiaries described herein are sold subject to TI’s
standard terms and conditions of sale. Customers are advised to obtain the
most current and complete information about TI products and services
before placing orders. TI assumes no liability for applications assistance,
customer’s applications or product designs, software performance, or
infringement of patents. The publication of information regarding any other
company’s products or services does not constitute TI’s approval, warranty
or endorsement thereof.
A042210
The platform bar, E2E, EasyScale, MSP430, controlCARD, Piccolo, PowerPAD,
C2000, TMS32C2000 and SimpLEDrive are trademarks of Texas Instruments.
All other trademarks are the property of their respective owners.
Cert no. SC-COC-001530
© 2010 Texas Instruments Incorporated
Printed in U.S.A. by Jarvis Press, Dallas, TX
SLYT349A
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DLP® Products
www.dlp.com
Communications and
Telecom
www.ti.com/communications
DSP
dsp.ti.com
Computers and
Peripherals
www.ti.com/computers
Clocks and Timers
www.ti.com/clocks
Consumer Electronics
www.ti.com/consumer-apps
Interface
interface.ti.com
Energy
www.ti.com/energy
Logic
logic.ti.com
Industrial
www.ti.com/industrial
Power Mgmt
power.ti.com
Medical
www.ti.com/medical
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
RFID
www.ti-rfid.com
Space, Avionics &
Defense
www.ti.com/space-avionics-defense
RF/IF and ZigBee® Solutions www.ti.com/lprf
Video and Imaging
www.ti.com/video
Wireless
www.ti.com/wireless-apps
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2010, Texas Instruments Incorporated