LM1877 www.ti.com SNAS550B – FEBRUARY 1995 – REVISED APRIL 2013 LM1877 Dual Audio Power Amplifier Check for Samples: LM1877 FEATURES DESCRIPTION • • • • • • • • The LM1877 is a monolithic dual power amplifier designed to deliver 2W/channel continuous into 8Ω loads. The LM1877 is designed to operate with a low number of external components, and still provide flexibility for use in stereo phonographs, tape recorders and AM-FM stereo receivers. Each power amplifier is biased from a common internal regulator to provide high power supply rejection, and output Q point centering. The LM1877 is internally compensated for all gains greater than 10. 1 2 2W/Channel −65 dB Ripple Rejection, Output Referred −65 dB Channel Separation, Output Referred Wide Supply Range, 6V–24V Very Low Cross-Over Distortion Low Audio Band Noise AC Short Circuit Protected Internal Thermal Shutdown APPLICATIONS • • • • • • • Multi-Channel Audio Systems Stereo Phonographs Tape Recorders and Players AM-FM Radio Receivers Servo Amplifiers Intercom Systems Automotive Products Connection Diagram Figure 1. 14-Pin SOIC or PDIP (Top View) See NPA0014B or NFF0014A Package 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 1995–2013, Texas Instruments Incorporated LM1877 SNAS550B – FEBRUARY 1995 – REVISED APRIL 2013 www.ti.com Equivalent Schematic Diagram These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Absolute Maximum Ratings (1) (2) Supply Voltage 26V Input Voltage ±0.7V Operating Temperature 0°C to +70°C −65°C to +150°C Storage Temperature Junction Temperature Lead Temperature 150°C PDIP Package Soldering (10 sec.) 260°C SOIC Package Infrared (15 sec.) 220°C SOIC Package Vapor Phase (60 sec.) Thermal Resistance (1) (2) 2 215°C θJC (PDIP Package) 30°C/W θJA (PDIP Package) 79°C/W θJC (SOIC Package) 27°C/W θJA (SOIC Package) 114°C/W Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and specifications. Submit Documentation Feedback Copyright © 1995–2013, Texas Instruments Incorporated Product Folder Links: LM1877 LM1877 www.ti.com SNAS550B – FEBRUARY 1995 – REVISED APRIL 2013 Electrical Characteristics VS = 20V, TA = 25°C (1) RL = 8Ω, AV = 50 (34 dB) unless otherwise specified Parameter Conditions Total Supply Current PO = 0W Output Power THD = 10% LM1877 VS = 20V, RL = 8Ω Min LM1877 Max Units 25 50 mA 2.0 VS = 12V, RL = 8Ω Total Harmonic Distortion Typ W/Ch 1.3 W/Ch PO = 50 mW/Channel 0.075 % PO = 500 mW/Channel 0.045 % f = 1 kHz, VS = 14V PO = 1 W/Channel 0.055 % Output Swing RL = 8Ω VS −6 Vp-p Channel Separation CF = 50 μF, CIN = 0.1 μF, −70 dB −60 dB −65 dB −40 dB 2.5 μV RS = 0, CN = 0.1 μF, AV 200 0.80 mV RS = 0, f = 100 kHz, RL = 8Ω 70 dB Input Offset Voltage 15 mV Input Bias Current 50 nA f = 1 kHz, Output Referred VS = 20V, VO = 4 Vrms −50 VS = 7V, VO = 0.5 Vrms PSRR Power Supply CF = 50 μF, CIN = 0.1 μF, Rejection Ratio f = 120 Hz, Output Referred VS = 20V, VRIPPLE = 1 Vrms −50 VS = 7V, VRIPPLE = 0.5 Vrms Noise Equivalent Input Noise RS = 0, CIN = 0.1 μF, BW = 20 Hz–20 kHz, Output Noise Wideband Open Loop Gain Input Impedance Open Loop DC Output Level VS = 20V 4 9 Slew Rate 10 MΩ 11 V 2.0 V/μs Power Bandwidth 65 kHz Current Limit 1.0 A (1) For operation at ambient temperature greater than 25°C, the LM1877 must be derated based on a maximum 150°C junction temperature. Submit Documentation Feedback Copyright © 1995–2013, Texas Instruments Incorporated Product Folder Links: LM1877 3 LM1877 SNAS550B – FEBRUARY 1995 – REVISED APRIL 2013 www.ti.com Typical Performance Characteristics 4 Device Dissipation vs Ambient Temperature Power Supply Rejection Ratio (Referred to the Output) vs Frequency Figure 2. Figure 3. Power Supply Rejection Ratio (Referred to the Output) vs Frequency Power Supply Rejection Ratio (Referred to the Output) vs Supply Voltage Figure 4. Figure 5. Channel Separation (Referred to the Output) vs Frequency Channel Separation (Referred to the Output) vs Frequency Figure 6. Figure 7. Submit Documentation Feedback Copyright © 1995–2013, Texas Instruments Incorporated Product Folder Links: LM1877 LM1877 www.ti.com SNAS550B – FEBRUARY 1995 – REVISED APRIL 2013 Typical Performance Characteristics (continued) Average Supply Current vs POUT Total Harmonic Distortion vs Frequency Figure 8. Figure 9. Total Harmonic Distortion vs Frequency Power Dissipation (W) Both Channels Operating Figure 10. Figure 11. Open Loop Gain vs Frequency Output Swing vs Supply Voltage Figure 12. Figure 13. Submit Documentation Feedback Copyright © 1995–2013, Texas Instruments Incorporated Product Folder Links: LM1877 5 LM1877 SNAS550B – FEBRUARY 1995 – REVISED APRIL 2013 www.ti.com Typical Applications Figure 14. Stereo Phonograph Amplifier with Bass Tone Control 6 Submit Documentation Feedback Copyright © 1995–2013, Texas Instruments Incorporated Product Folder Links: LM1877 LM1877 www.ti.com SNAS550B – FEBRUARY 1995 – REVISED APRIL 2013 Figure 15. Frequency Response of Bass Tone Control Figure 16. Inverting Unity Gain Amplifier Figure 17. Stereo Amplifier with AV = 200 Submit Documentation Feedback Copyright © 1995–2013, Texas Instruments Incorporated Product Folder Links: LM1877 7 LM1877 SNAS550B – FEBRUARY 1995 – REVISED APRIL 2013 www.ti.com Figure 18. Non-Inverting Amplifier Using Split Supply 8 Figure 19. Typical Split Supply Submit Documentation Feedback Copyright © 1995–2013, Texas Instruments Incorporated Product Folder Links: LM1877 LM1877 www.ti.com SNAS550B – FEBRUARY 1995 – REVISED APRIL 2013 REVISION HISTORY Changes from Revision A (April 2013) to Revision B • Page Changed layout of National Data Sheet to TI format ............................................................................................................ 7 Submit Documentation Feedback Copyright © 1995–2013, Texas Instruments Incorporated Product Folder Links: LM1877 9 PACKAGE OPTION ADDENDUM www.ti.com 26-Aug-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (°C) Device Marking (3) (4/5) LM1877M-9/NOPB ACTIVE SOIC NPA 14 50 Green (RoHS & no Sb/Br) CU SN Level-3-260C-168 HR 0 to 70 LM1877M -9 LM1877MX-9/NOPB ACTIVE SOIC NPA 14 1000 Green (RoHS & no Sb/Br) CU SN Level-3-260C-168 HR 0 to 70 LM1877M -9 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 Samples PACKAGE MATERIALS INFORMATION www.ti.com 8-Apr-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device LM1877MX-9/NOPB Package Package Pins Type Drawing SOIC NPA 14 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 1000 330.0 16.4 Pack Materials-Page 1 10.9 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 9.5 3.2 12.0 16.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 8-Apr-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM1877MX-9/NOPB SOIC NPA 14 1000 367.0 367.0 38.0 Pack Materials-Page 2 MECHANICAL DATA NPA0014B www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2013, Texas Instruments Incorporated