CY7C1325G 4-Mbit (256 K × 18) Flow-Through Sync SRAM 4-Mbit (256 K × 18) Flow-Through Sync SRAM Features Functional Description ■ 256 K × 18 common I/O ■ 3.3 V core power supply (VDD) ■ 2.5 V or 3.3 V I/O power supply (VDDQ) ■ Fast clock-to-output times ■ 6.5 ns (133 MHz version) ■ Provide high performance 2-1-1-1 access rate ■ User selectable burst counter supporting Intel Pentium interleaved or linear burst sequences ■ Separate processor and controller address strobes ■ Synchronous self timed write ■ Asynchronous output enable ■ Available in Pb-free 100-pin TQFP package ■ “ZZ” sleep mode option The CY7C1325G is a 256 K × 18 synchronous cache RAM designed to interface with high speed microprocessors with minimum glue logic. Maximum access delay from clock rise is 6.5 ns (133 MHz version). A 2 bit on-chip counter captures the first address in a burst and increments the address automatically for the rest of the burst access. All synchronous inputs are gated by registers controlled by a positive-edge-triggered Clock Input (CLK). The synchronous inputs include all addresses, all data inputs, address-pipelining chip enable (CE1), depth-expansion chip enables (CE2 and CE3), burst control inputs (ADSC, ADSP, and ADV), write enables (BW[A:B], and BWE), and global write (GW). Asynchronous inputs include the output enable (OE) and the ZZ pin. The CY7C1325G allows either interleaved or linear burst sequences, selected by the MODE input pin. A HIGH selects an interleaved burst sequence, while a LOW selects a linear burst sequence. Burst accesses can be initiated with the processor address strobe (ADSP) or the cache controller address strobe (ADSC) inputs. Addresses and chip enables are registered at rising edge of clock when either address strobe processor (ADSP) or address strobe controller (ADSC) are active. Subsequent burst addresses can be internally generated as controlled by the advance pin (ADV). The CY7C1325G operates from a +3.3 V core power supply while all outputs may operate with either a +2.5 or +3.3 V supply. All inputs and outputs are JEDEC-standard JESD8-5-compatible. For a complete list of related documentation, click here. Logic Block Diagram A 0,A1,A ADDRESS REGISTER A[1:0] MODE BURST Q1 COUNTER AND LOGIC CLR Q0 ADV CLK ADSC ADSP BW B BW A DQ B ,DQP B WRITE DRIVER DQ B ,DQP B WRITE REGISTER MEMORY ARRAY SENSE AMPS OUTPUT BUFFERS DQs DQP A DQP B DQ A ,DQP A WRITE DRIVER DQ A ,DQP A WRITE REGISTER BWE GW CE 1 CE 2 CE 3 INPUT REGISTERS ENABLE REGISTER OE ZZ SLEEP CONTROL Cypress Semiconductor Corporation Document Number: 38-05518 Rev. *P • 198 Champion Court • San Jose, CA 95134-1709 • 408-943-2600 Revised November 19, 2014 CY7C1325G Contents Selection Guide ................................................................ 3 Pin Configurations ........................................................... 3 Pin Definitions .................................................................. 4 Functional Overview ........................................................ 6 Single Read Accesses ................................................ 6 Single Write Accesses Initiated by ADSP ................... 6 Single Write Accesses Initiated by ADSC ................... 6 Burst Sequences ......................................................... 6 Sleep Mode ................................................................. 6 Interleaved Burst Address Table ................................. 7 Linear Burst Address Table ......................................... 7 ZZ Mode Electrical Characteristics .............................. 7 Truth Table ........................................................................ 8 Truth Table for Read/Write .............................................. 9 Maximum Ratings ........................................................... 10 Operating Range ............................................................. 10 Neutron Soft Error Immunity ......................................... 10 Electrical Characteristics ............................................... 10 Capacitance .................................................................... 11 Thermal Resistance ........................................................ 11 AC Test Loads and Waveforms ..................................... 12 Switching Characteristics .............................................. 13 Timing Diagrams ............................................................ 14 Ordering Information ...................................................... 18 Ordering Code Definitions ......................................... 18 Package Diagrams .......................................................... 19 Acronyms ........................................................................ 20 Document Conventions ................................................. 20 Units of Measure ....................................................... 20 Errata ............................................................................... 21 Part Numbers Affected .............................................. 21 Product Status ........................................................... 21 Ram9 Sync ZZ Pin Issues Errata Summary .............. 21 Document History Page ................................................. 22 Sales, Solutions, and Legal Information ...................... 24 Worldwide Sales and Design Support ....................... 24 Products .................................................................... 24 PSoC® Solutions ...................................................... 24 Cypress Developer Community ................................. 24 Technical Support ..................................................... 24 Errata: For information on silicon errata, see "Errata" on page 21. Details include trigger conditions, devices affected, and proposed workaround. Document Number: 38-05518 Rev. *P Page 2 of 24 CY7C1325G Selection Guide Description Maximum access time Maximum operating current Maximum standby current 133 MHz 6.5 Unit ns 225 40 mA mA Pin Configurations A 45 46 47 48 49 50 A A A A A 44 43 NC/9M A A 41 VDD NC/18M 42 40 37 A0 VSS 36 A1 39 35 A 38 34 NC/72M NC/36M 33 81 82 83 84 BWE GW OE ADSC ADSP ADV A 85 86 87 CLK 89 88 VDD VSS 91 90 BWA CE3 93 92 NC 96 BWB NC 97 94 CE2 98 95 A CE1 99 A 31 VSS VDDQ NC NC NC A VSS DQB DQB VDDQ VSS DQB DQB DQPB NC 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 CY7C1325G A BYTE B DQB DQB VSS VDDQ DQB DQB NC VDD NC 32 VDDQ VSS NC NC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 MODE A NC NC NC 100 Figure 1. 100-pin TQFP (14 × 20 × 1.4 mm) pinout [1] A NC NC VDDQ VSS NC DQPA DQA DQA VSS VDDQ DQA DQA VSS NC BYTE A VDD ZZ DQA DQA VDDQ VSS DQA DQA NC NC VSS VDDQ NC NC NC Note 1. Errata: The ZZ pin (Pin 64) needs to be externally connected to ground. For more information, see "Errata" on page 21. Document Number: 38-05518 Rev. *P Page 3 of 24 CY7C1325G Pin Definitions Name I/O Description A0, A1, A InputAddress inputs used to select one of the 256 K address locations. Sampled at the rising edge of synchronous the CLK if ADSP or ADSC is active LOW, and CE1, CE2, and CE3 are sampled active. A[1:0] feed the 2 bit counter. BWA,BWB InputByte write select inputs, active LOW. Qualified with BWE to conduct byte writes to the SRAM. Sampled synchronous on the rising edge of CLK. GW InputGlobal write enable input, active LOW. When asserted LOW on the rising edge of CLK, a global write synchronous is conducted (all bytes are written, regardless of the values on BW[A:B] and BWE). BWE InputByte write enable input, active LOW. Sampled on the rising edge of CLK. This signal must be asserted synchronous LOW to conduct a byte write. CLK Input-clock Clock input. Used to capture all synchronous inputs to the device. Also used to increment the burst counter when ADV is asserted LOW, during a burst operation. CE1 InputChip enable 1 input, active LOW. Sampled on the rising edge of CLK. Used in conjunction with CE2 synchronous and CE3 to select/deselect the device. ADSP is ignored if CE1 is HIGH. CE1 is sampled only when a new external address is loaded. CE2 InputChip enable 2 input, active HIGH. Sampled on the rising edge of CLK. Used in conjunction with CE1 synchronous and CE3 to select/deselect the device. CE2 is sampled only when a new external address is loaded. CE3 InputChip enable 3 input, active LOW. Sampled on the rising edge of CLK. Used in conjunction with CE1 synchronous and CE2 to select/deselect the device. CE3 is sampled only when a new external address is loaded. OE InputOutput enable, asynchronous input, active LOW. Controls the direction of the I/O pins. When LOW, asynchronous the I/O pins behave as outputs. When deasserted HIGH, I/O pins are tristated, and act as input data pins. OE is masked during the first clock of a read cycle when emerging from a deselected state. ADV InputAdvance input signal, sampled on the rising edge of CLK. When asserted, it automatically synchronous increments the address in a burst cycle. ADSP InputAddress strobe from processor, sampled on the rising edge of CLK, active LOW. When asserted synchronous LOW, addresses presented to the device are captured in the address registers. A[1:0] are also loaded into the burst counter. When ADSP and ADSC are both asserted, only ADSP is recognized. ASDP is ignored when CE1 is deasserted HIGH. ADSC InputAddress strobe from controller, sampled on the rising edge of CLK, active LOW. When asserted synchronous LOW, addresses presented to the device are captured in the address registers. A[1:0] are also loaded into the burst counter. When ADSP and ADSC are both asserted, only ADSP is recognized. ZZ[2] InputZZ “sleep” input, active HIGH. When asserted HIGH places the device in a non-time-critical “sleep” asynchronous condition with data integrity preserved.During normal operation, this pin has to be low or left floating. ZZ pin has an internal pull-down. DQs DQPA, DQPB I/OBidirectional data I/O lines. As inputs, they feed into an on-chip data register that is triggered by the synchronous rising edge of CLK. As outputs, they deliver the data contained in the memory location specified by the addresses presented during the previous clock rise of the read cycle. The direction of the pins is controlled by OE. When OE is asserted LOW, the pins behave as outputs. When HIGH, DQs and DQP[A:B] are placed in a tristate condition. Note 2. Errata: The ZZ pin (Pin 64) needs to be externally connected to ground. For more information, see "Errata" on page 21. Document Number: 38-05518 Rev. *P Page 4 of 24 CY7C1325G Pin Definitions (continued) Name VDD VSS I/O Description Power supply Power supply inputs to the core of the device. Ground Ground for the core of the device. VDDQ I/O power supply Power supply for the I/O circuitry. MODE Inputstatic Selects burst order. When tied to GND selects linear burst sequence. When tied to VDD or left floating selects interleaved burst sequence. This is a strap pin and should remain static during device operation. Mode pin has an internal pull-up. NC – No connects. Not Internally connected to the die. NC/9M, NC/18M, NC/36M, NC/72M, NC/144M, NC/288M, NC/576M, NC/1G – No connects. Not internally connected to the die. NC/9M, NC/18M, NC/36M, NC/72M, NC/144M, NC/288M, NC/576M and NC/1G are address expansion pins that are not internally connected to the die. Document Number: 38-05518 Rev. *P Page 5 of 24 CY7C1325G Functional Overview All synchronous inputs pass through input registers controlled by the rising edge of the clock. Maximum access delay from the clock rise (t CDV) is 6.5 ns (133 MHz device). The CY7C1325G supports secondary cache in systems utilizing either a linear or interleaved burst sequence. The interleaved burst order supports Pentium and i486 processors. The linear burst sequence is suited for processors that utilize a linear burst sequence. The burst order is user-selectable, and is determined by sampling the MODE input. Accesses can be initiated with either the processor address strobe (ADSP) or the controller address strobe (ADSC). Address advancement through the burst sequence is controlled by the ADV input. A two bit on-chip wraparound burst counter captures the first address in a burst sequence and automatically increments the address for the rest of the burst access. Byte write operations are qualified with the byte write enable (BWE) and byte write select (BW[A:B]) inputs. A global write enable (GW) overrides all byte write inputs and writes data to all four bytes. All writes are simplified with on-chip synchronous self timed write circuitry. Three synchronous chip selects (CE1, CE2, CE3) and an asynchronous output enable (OE) provide for easy bank selection and output tristate control. ADSP is ignored if CE1 is HIGH. Single Read Accesses A single read access is initiated when the following conditions are satisfied at clock rise: (1) CE1, CE2, and CE3 are all asserted active, and (2) ADSP or ADSC is asserted LOW (if the access is initiated by ADSC, the write inputs must be deasserted during this first cycle). The address presented to the address inputs is latched into the address register and the burst counter/control logic and presented to the memory core. If the OE input is asserted LOW, the requested data is available at the data outputs, a maximum to tCDV after clock rise. ADSP is ignored if CE1 is HIGH. Single Write Accesses Initiated by ADSP This access is initiated when the following conditions are satisfied at clock rise: (1) CE1, CE2, CE3 are all asserted active, and (2) ADSP is asserted LOW. The addresses presented are loaded into the address register and the burst inputs (GW, BWE, and BW[A:B]) are ignored during this first clock cycle. If the write inputs are asserted active (see Write Cycle Descriptions table for appropriate states that indicate a write) on the next clock rise, the Document Number: 38-05518 Rev. *P appropriate data is latched and written into the device. Byte writes are allowed. During byte writes, BWA controls DQA and BWB controls DQB. All I/Os are tristated during a byte write.Since this is a common I/O device, the asynchronous OE input signal must be deasserted and the I/Os must be tristated prior to the presentation of data to DQs. As a safety precaution, the data lines are tristated after a write cycle is detected, regardless of the state of OE. Single Write Accesses Initiated by ADSC This write access is initiated when the following conditions are satisfied at clock rise: (1) CE1, CE2, and CE3 are all asserted active, (2) ADSC is asserted LOW, (3) ADSP is deasserted HIGH, and (4) the write input signals (GW, BWE, and BW[A:B]) indicate a write access. ADSC is ignored if ADSP is active LOW. The addresses presented are loaded into the address register and the burst counter/control logic and delivered to the memory core. The information presented to DQ[A:D] is written into the specified address location. Byte writes are allowed. During byte writes, BWA controls DQA, BWB controls DQB. All I/Os are tristated when a write is detected, even a byte write. Since this is a common I/O device, the asynchronous OE input signal must be deasserted and the I/Os must be tristated prior to the presentation of data to DQs. As a safety precaution, the data lines are tristated after a write cycle is detected, regardless of the state of OE. Burst Sequences The CY7C1325G provides an on-chip two bit wraparound burst counter inside the SRAM. The burst counter is fed by A[1:0], and can follow either a linear or interleaved burst order. The burst order is determined by the state of the MODE input. A LOW on MODE selects a linear burst sequence. A HIGH on MODE selects an interleaved burst order. Leaving MODE unconnected causes the device to default to a interleaved burst sequence. Sleep Mode The ZZ input pin is an asynchronous input. Asserting ZZ places the SRAM in a power conservation “sleep” mode. Two clock cycles are required to enter into or exit from this “sleep” mode. While in this mode, data integrity is guaranteed. Accesses pending when entering the “sleep” mode are not considered valid nor is the completion of the operation guaranteed. The device must be deselected prior to entering the “sleep” mode. CEs, ADSP, and ADSC must remain inactive for the duration of tZZREC after the ZZ input returns LOW. Page 6 of 24 CY7C1325G Interleaved Burst Address Table Linear Burst Address Table (MODE = Floating or VDD) (MODE = GND) First Address A1:A0 Second Address A1:A0 Third Address A1:A0 Fourth Address A1:A0 First Address A1:A0 Second Address A1:A0 Third Address A1:A0 00 01 01 00 Fourth Address A1:A0 10 11 00 01 10 11 11 10 01 10 11 00 10 11 00 01 10 11 00 01 11 10 01 00 11 00 01 10 ZZ Mode Electrical Characteristics Parameter Description Test Conditions Min Max Unit IDDZZ Sleep mode standby current ZZ > VDD– 0.2 V – 40 mA tZZS Device operation to ZZ ZZ > VDD – 0.2 V – 2tCYC ns tZZREC ZZ recovery time ZZ < 0.2 V 2tCYC – ns tZZI ZZ active to sleep current This parameter is sampled – 2tCYC ns tRZZI ZZ inactive to exit sleep current This parameter is sampled 0 – ns Document Number: 38-05518 Rev. *P Page 7 of 24 CY7C1325G Truth Table The Truth Table for part CY7C1325G is as follows. [3, 4, 5, 6, 7] Cycle Description Address Used CE1 CE2 CE3 ZZ ADSP ADSC ADV WRITE OE CLK DQ Deselected cycle, power-down None H X X L X L X X X L–H Tri-state Deselected cycle, power-down None L L X L L X X X X L–H Tri-state Deselected cycle, power-down None L X H L L X X X X L–H Tri-state Deselected cycle, power-down None L L X L H L X X X L–H Tri-state Deselected cycle, power-down None X X X L H L X X X L–H Tri-state Sleep mode, power-down None X X X H X X X X X X Tri-state Read cycle, begin burst External L H L L L X X X L L–H Q Read cycle, begin burst External L H L L L X X X H L–H Tri-state Write cycle, begin burst External L H L L H L X L X L–H D Read cycle, begin burst External L H L L H L X H L L–H Q Read cycle, begin burst External L H L L H L X H H L–H Tri-state Read cycle, continue burst Next X X X L H H L H L L–H Q Read cycle, continue burst Next X X X L H H L H H L–H Tri-state Read cycle, continue burst Next H X X L X H L H L L–H Q Read cycle, continue burst Next H X X L X H L H H L–H Tri-state Write cycle, continue burst Next X X X L H H L L X L–H D Write cycle, continue burst Next H X X L X H L L X L–H D Read cycle, suspend burst Current X X X L H H H H L L–H Q Read cycle, suspend burst Current X X X L H H H H H L–H Tri-state Read cycle, suspend burst Current H X X L X H H H L L–H Q Read cycle, suspend burst Current H X X L X H H H H L–H Tri-state Write cycle, suspend burst Current X X X L H H H L X L–H D Write cycle, suspend burst Current H X X L X H H L X L–H D Notes 3. X = “Don’t Care.” H = Logic HIGH, L = Logic LOW. 4. WRITE = L when any one or more Byte Write enable signals (BWA, BWB) and BWE = L or GW = L. WRITE = H when all Byte write enable signals (BWA, BWB), BWE, GW = H. 5. The DQ pins are controlled by the current cycle and the OE signal. OE is asynchronous and is not sampled with the clock. 6. The SRAM always initiates a read cycle when ADSP is asserted, regardless of the state of GW, BWE, or BW[A: B]. Writes may occur only on subsequent clocks after the ADSP or with the assertion of ADSC. As a result, OE must be driven HIGH prior to the start of the write cycle to allow the outputs to tristate. OE is a don't care for the remainder of the write cycle. 7. OE is asynchronous and is not sampled with the clock rise. It is masked internally during write cycles. During a read cycle all data bits are tristate when OE is inactive or when the device is deselected, and all data bits behave as output when OE is active (LOW). Document Number: 38-05518 Rev. *P Page 8 of 24 CY7C1325G Truth Table for Read/Write The Truth Table for Read/Write for part CY7C1325G is as follows. [8] Function GW BWE BWB BWA Read H H X X Read H L H H Write byte A – (DQA and DQPA) H L H L Write byte B – (DQB and DQPB) H L L H Write all bytes H L L L Write all bytes L X X X Note 8. X = “Don’t Care.” H = Logic HIGH, L = Logic LOW. Document Number: 38-05518 Rev. *P Page 9 of 24 CY7C1325G Maximum Ratings Operating Range Exceeding maximum ratings may shorten the useful life of the device. User guidelines are not tested. Storage temperature ................................ –65 °C to +150 °C Range Ambient Temperature Commercial 0 °C to +70 °C Ambient temperature with power applied .......................................... –55 °C to +125 °C Supply voltage on VDD relative to GND .......–0.5 V to +4.6 V Supply voltage on VDDQ relative to GND ...... –0.5 V to +VDD DC voltage applied to outputs in tristate ...........................................–0.5 V to VDDQ + 0.5 V DC input voltage ................................. –0.5 V to VDD + 0.5 V Current into outputs (LOW) ........................................ 20 mA Static discharge voltage (per MIL-STD-883, method 3015) .......................... > 2001 V Latch-up current .................................................... > 200 mA VDD VDDQ 3.3 V5% / 2.5 V – 5% to + 10% VDD Neutron Soft Error Immunity Parameter Description Test Conditions Typ Max* Unit LSBU Logical single bit upsets 25 °C 361 394 FIT/ Mb LMBU Logical multi bit upsets 25 °C 0 0.01 FIT/ Mb SEL Single event latch up 85 °C 0 0.1 FIT/ Dev * No LMBU or SEL events occurred during testing; this column represents a statistical 2, 95% confidence limit calculation. For more details refer to Application Note AN54908 “Accelerated Neutron SER Testing and Calculation of Terrestrial Failure Rates”. Electrical Characteristics Over the Operating Range Parameter [9, 10] Description Test Conditions Min Max Unit VDD Power supply voltage 3.135 3.6 V VDDQ I/O supply voltage 2.375 VDD V VOH Output HIGH voltage for 3.3 V I/O, IOH = –4.0 mA 2.4 – V for 2.5 V I/O, IOH = –1.0 mA 2.0 – V for 3.3 V I/O, IOL = 8.0 mA – 0.4 V for 2.5 V I/O, IOL = 1.0 mA – 0.4 V for 3.3 V I/O 2.0 VDD + 0.3 V for 2.5 V I/O 1.7 VDD + 0.3 V for 3.3 V I/O –0.3 0.8 V for 2.5 V I/O –0.3 0.7 V Input leakage current except ZZ GND VI VDDQ and MODE 5 5 A Input current of MODE Input = VSS –30 – A Input = VDD – 5 A Input current of ZZ Input = VSS –5 – A Input = VDD – 30 A IOZ Output leakage current GND VI VDDQ, output disabled –5 5 A IDD VDD operating supply current VDD = Max, IOUT = 0 mA, f = fMAX= 1/tCYC – 225 mA VOL VIH VIL IX Output LOW voltage Input HIGH voltage Input LOW voltage[9] 7.5 ns cycle, 133 MHz Notes 9. Overshoot: VIH(AC) < VDD + 1.5 V (Pulse width less than tCYC/2), undershoot: VIL(AC) > –2 V (Pulse width less than tCYC/2). 10. Tpower up: Assumes a linear ramp from 0 V to VDD(min) within 200 ms. During this time VIH < VDD and VDDQ < VDD. Document Number: 38-05518 Rev. *P Page 10 of 24 CY7C1325G Electrical Characteristics (continued) Over the Operating Range Parameter [9, 10] Description Test Conditions Min Max Unit ISB1 Automatic CE power-down current – TTL inputs Max VDD, device deselected, VIN VIH or VIN VIL, f = fMAX, inputs switching 7.5 ns cycle, 133 MHz – 90 mA ISB2 Automatic CE power-down current – CMOS inputs Max VDD, device deselected, 7.5 ns cycle, VIN VDD – 0.3 V or VIN 0.3 V, 133 MHz f = 0, inputs static – 40 mA ISB3 Automatic CE power-down current – CMOS inputs 7.5 ns cycle, Max VDD, device deselected, VIN VDDQ – 0.3 V or VIN 0.3 V, 133 MHz f = fMAX, inputs switching – 75 mA ISB4 Automatic CE power-down current – TTL inputs 7.5 ns cycle, Max VDD, device deselected, VIN VDD – 0.3 V or VIN 0.3 V, 133 MHz f = 0, inputs static – 45 mA Capacitance Parameter [11] Description CIN Input capacitance CCLK Clock input capacitance CI/O Input/Output capacitance 100-pin TQFP Max Unit 5 pF 5 pF 5 pF Test Conditions 100-pin TQFP Package Unit Test conditions follow standard test methods and procedures for measuring thermal impedance, per EIA/JESD51. 30.32 °C/W 6.85 °C/W Test Conditions TA = 25 C, f = 1 MHz, VDD = 3.3 V, VDDQ = 3.3 V Thermal Resistance Parameter [11] Description JA Thermal resistance (junction to ambient) JC Thermal resistance (junction to case) Note 11. Tested initially and after any design or process change that may affect these parameters. Document Number: 38-05518 Rev. *P Page 11 of 24 CY7C1325G AC Test Loads and Waveforms Figure 2. AC Test Loads and Waveforms 3.3 V I/O Test Load 3.3 V OUTPUT R = 317 Z0 = 50 VT = 1.5 V (a) 2.5 V I/O Test Load 5 pF INCLUDING JIG AND SCOPE 2.5 V OUTPUT GND R = 351 VT = 1.25 V (a) Document Number: 38-05518 Rev. *P 5 pF INCLUDING JIG AND SCOPE 10% 1 ns 1 ns (c) R = 1667 ALL INPUT PULSES VDDQ GND R = 1538 (b) 90% 10% 90% (b) OUTPUT RL = 50 Z0 = 50 ALL INPUT PULSES VDDQ OUTPUT RL = 50 10% 90% 10% 90% 1 ns 1 ns (c) Page 12 of 24 CY7C1325G Switching Characteristics Over the Operating Range Parameter [12, 13] tPOWER Description VDD(typical) to the first access [14] -133 Unit Min Max 1 – ms Clock tCYC Clock cycle time 7.5 – ns tCH Clock HIGH 2.5 – ns tCL Clock LOW 2.5 – ns Output Times tCDV Data output valid after CLK rise – 6.5 ns tDOH Data output hold after CLK rise 2.0 – ns 0 – ns – 3.5 ns – 3.5 ns 0 – ns – 3.5 ns [15, 16, 17] tCLZ Clock to low Z tCHZ Clock to high Z [15, 16, 17] tOEV OE LOW to output valid tOELZ tOEHZ OE LOW to output low Z [15, 16, 17] OE HIGH to output high Z [15, 16, 17] Setup Times tAS Address setup before CLK rise 1.5 – ns tADS ADSP, ADSC setup before CLK rise 1.5 – ns tADVS ADV setup before CLK rise 1.5 – ns tWES GW, BWE, BWX setup before CLK rise 1.5 – ns tDS Data input setup before CLK rise 1.5 – ns tCES Chip enable setup 1.5 – ns tAH Address hold after CLK rise 0.5 – ns tADH ADSP, ADSC hold after CLK rise 0.5 – ns tWEH GW, BWE, BWX hold after CLK rise 0.5 – ns tADVH ADV hold after CLK rise 0.5 – ns tDH Data input hold after CLK rise 0.5 – ns tCEH Chip enable hold after CLK rise 0.5 – ns Hold Times Notes 12. Timing reference level is 1.5 V when VDDQ = 3.3 V and is 1.25 V when VDDQ = 2.5 V. 13. Test conditions shown in (a) of Figure 2 on page 12 unless otherwise noted. 14. This part has a voltage regulator internally; tPOWER is the time that the power needs to be supplied above VDD(minimum) initially before a read or write operation can be initiated. 15. tCHZ, tCLZ, tOELZ, and tOEHZ are specified with AC test conditions shown in part (b) of Figure 2 on page 12. Transition is measured ± 200 mV from steady-state voltage. 16. At any voltage and temperature, tOEHZ is less than tOELZ and tCHZ is less than tCLZ to eliminate bus contention between SRAMs when sharing the same data bus. These specifications do not imply a bus contention condition, but reflect parameters guaranteed over worst case user conditions. Device is designed to achieve high Z prior to low Z under the same system conditions. 17. This parameter is sampled and not 100% tested. Document Number: 38-05518 Rev. *P Page 13 of 24 CY7C1325G Timing Diagrams Figure 3. Read Cycle Timing [18] tCYC CLK t t ADS CH t CL tADH ADSP t ADS tADH ADSC t AS tAH A1 ADDRESS A2 t GW, BWE,BW WES t WEH [A:B] t CES Deselect Cycle t CEH CE t ADVS t ADVH ADV ADV suspends burst OE t OEV t OEHZ t CLZ Data Out (Q) High-Z Q(A1) t CDV t OELZ t CHZ t DOH Q(A2) Q(A2 + 1) Q(A2 + 2) t CDV Q(A2 + 3) Q(A2) Q(A2 + 1) Q(A2 + 2) Burst wraps around to its initial state Single READ BURST READ DON’T CARE UNDEFINED Note 18. On this diagram, when CE is LOW: CE1 is LOW, CE2 is HIGH and CE3 is LOW. When CE is HIGH: CE1 is HIGH or CE2 is LOW or CE3 is HIGH. Document Number: 38-05518 Rev. *P Page 14 of 24 CY7C1325G Timing Diagrams (continued) Figure 4. Write Cycle Timing [19, 20] t CYC CLK t t ADS CH t CL tADH ADSP t ADS ADSC extends burst tADH t ADS tADH ADSC t AS tAH A1 ADDRESS A2 A3 Byte write signals are ignored for first cycle when ADSP initiates burst t WES tWEH BWE, [A:B] BW t WES t WEH GW t CES tCEH CE t ADVS tADVH ADV ADV suspends burst OE t Data in (D) High-Z t DS t DH D(A1) D(A2) D(A2 + 1) D(A2 + 1) D(A2 + 2) D(A2 + 3) D(A3) D(A3 + 1) D(A3 + 2) OEHZ Data Out (Q) BURST READ Single WRITE BURST WRITE DON’T CARE Extended BURST WRITE UNDEFINED Notes 19. On this diagram, when CE is LOW: CE1 is LOW, CE2 is HIGH and CE3 is LOW. When CE is HIGH: CE1 is HIGH or CE2 is LOW or CE3 is HIGH. 20. Full width write can be initiated by either GW LOW; or by GW HIGH, BWE LOW and BW[A:B] LOW. Document Number: 38-05518 Rev. *P Page 15 of 24 CY7C1325G Timing Diagrams (continued) Figure 5. Read/Write Timing [21, 22, 23] tCYC CLK t t ADS CH t CL tADH ADSP ADSC t AS ADDRESS A1 tAH A2 A3 A4 t BWE, BW WES t A5 A6 D(A5) D(A6) WEH [A:B] t CES tCEH CE ADV OE t DS Data In (D) Data Out (Q) High-Z t OEHZ Q(A1) tDH t OELZ D(A3) t CDV Q(A4) Q(A2) Back-to-Back READs Single WRITE Q(A4+1) BURST READ DON’T CARE Q(A4+2) Q(A4+3) Back-to-Back WRITEs UNDEFINED Notes 21. On this diagram, when CE is LOW: CE1 is LOW, CE2 is HIGH and CE3 is LOW. When CE is HIGH: CE1 is HIGH or CE2 is LOW or CE3 is HIGH. 22. The data bus (Q) remains in High Z following a WRITE cycle, unless a new read access is initiated by ADSP or ADSC. 23. GW is HIGH. Document Number: 38-05518 Rev. *P Page 16 of 24 CY7C1325G Timing Diagrams (continued) Figure 6. ZZ Mode Timing [24, 25] CLK t ZZ I t ZZ ZZREC t ZZI SUPPLY I t RZZI DDZZ A LL INPUTS (except ZZ) Outputs (Q) DESELECT or READ Only High-Z DON’T CARE Notes 24. Device must be deselected when entering ZZ mode. See Cycle Descriptions table for all possible signal conditions to deselect the device. 25. DQs are in High Z when exiting ZZ sleep mode. Document Number: 38-05518 Rev. *P Page 17 of 24 CY7C1325G Ordering Information The table below contains only the parts that are currently available. If you don’t see what you are looking for, please contact your local sales representative. For more information, visit the Cypress website at www.cypress.com and refer to the product summary page at http://www.cypress.com/products Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives and distributors. To find the office closest to you, visit us at http://www.cypress.com/go/datasheet/offices Speed (MHz) 133 Package Diagram Ordering Code CY7C1325G-133AXC Part and Package Type 51-85050 100-pin TQFP (14 × 20 × 1.4 mm) Pb-free Operating Range Commercial Ordering Code Definitions CY 7 C 1325 G - 133 A X C Temperature Range: C = Commercial Pb-free Package Type: A = 100-pin TQFP Speed Grade: 133 MHz Process Technology: G 90nm Part Identifier: 1325 = FT, 256 Kb × 18 (4 Mb) Technology Code: C = CMOS Marketing Code: 7 = SRAM Company ID: CY = Cypress Document Number: 38-05518 Rev. *P Page 18 of 24 CY7C1325G Package Diagrams Figure 7. 100-pin TQFP (14 × 20 × 1.4 mm) A100RA Package Outline, 51-85050 51-85050 *E Document Number: 38-05518 Rev. *P Page 19 of 24 CY7C1325G Acronyms Acronym Document Conventions Description Units of Measure CMOS Complementary Metal Oxide Semiconductor CE Chip Enable °C degree Celsius CEN Clock Enable MHz megahertz EIA Electronic Industries Alliance µA microampere I/O Input/Output mA milliampere JEDEC Joint Electron Devices Engineering Council mm millimeter OE Output Enable ms millisecond SRAM Static Random Access Memory mV millivolt TQFP Thin Quad Flat Pack ns nanosecond TTL Transistor-Transistor Logic ohm WE Write Enable % percent pF picofarad V volt W watt Document Number: 38-05518 Rev. *P Symbol Unit of Measure Page 20 of 24 CY7C1325G Errata This section describes the Ram9 Sync ZZ pin issue. Details include trigger conditions, the devices affected, proposed workaround and silicon revision applicability. Please contact your local Cypress sales representative if you have further questions. Part Numbers Affected Density & Revision Package Type Operating Range 4Mb-Ram9 Synchronous SRAMs: CY7C132*G 100-pin TQFP Commercial Product Status All of the devices in the Ram9 4Mb Sync family are qualified and available in production quantities. Ram9 Sync ZZ Pin Issues Errata Summary The following table defines the errata applicable to available Ram9 4Mb Sync family devices. Item 1. Issues ZZ Pin Description Device When asserted HIGH, the ZZ pin places device in a “sleep” condition with data integrity preserved.The ZZ pin currently does not have an internal pull-down resistor and hence cannot be left floating externally by the user during normal mode of operation. 4M-Ram9 (90nm) Fix Status For the 4M Ram9 (90 nm) devices, there is no plan to fix this issue. 1. ZZ Pin Issue ■ PROBLEM DEFINITION The problem occurs only when the device is operated in the normal mode with ZZ pin left floating. The ZZ pin on the SRAM device does not have an internal pull-down resistor. Switching noise in the system may cause the SRAM to recognize a HIGH on the ZZ input, which may cause the SRAM to enter sleep mode. This could result in incorrect or undesirable operation of the SRAM. ■ TRIGGER CONDITIONS Device operated with ZZ pin left floating. ■ SCOPE OF IMPACT When the ZZ pin is left floating, the device delivers incorrect data. ■ WORKAROUND Tie the ZZ pin externally to ground. ■ FIX STATUS For the 4M Ram9 (90 nm) devices, there is no plan to fix this issue. Document Number: 38-05518 Rev. *P Page 21 of 24 CY7C1325G Document History Page Document Title: CY7C1325G, 4-Mbit (256 K × 18) Flow-Through Sync SRAM Document Number: 38-05518 Rev. ECN Orig. of Change Submission Date ** 224366 RKF See ECN New data sheet. *A 283775 VBL See ECN Updated Features (Removed 66 MHz frequency related information). Updated Selection Guide (Removed 66 MHz frequency related information). Updated Electrical Characteristics (Removed 66 MHz frequency related information). Updated Switching Characteristics (Removed 66 MHz frequency related information). Updated Ordering Information (Updated part numbers (Removed 66 MHz frequency related information, changed TQFP package to Pb-Free TQFP, added BG Pb-Free package)). *B 333626 SYT See ECN Updated Features (Removed 117 MHz frequency related information). Updated Selection Guide (Removed 117 MHz frequency related information). Updated Pin Configurations (Modified Address Expansion balls in the pinouts for 100-pin TQFP and 119-ball BGA Packages as per JEDEC standards). Updated Pin Definitions. Updated Functional Overview (Updated ZZ Mode Electrical Characteristics (Replaced “Snooze” with “Sleep”)). Updated Truth Table (Replaced “Snooze” with “Sleep”). Updated Electrical Characteristics (Updated Test Conditions of VOL, VOH parameters, removed 117 MHz frequency related information). Updated Thermal Resistance (Replaced values of JA and JC parameters from TBD to their respective values). Updated Switching Characteristics (Removed 117 MHz frequency related information). Updated Ordering Information (By shading and unshading MPNs as per availability, changed the package name for 100-pin TQFP from A100RA to A101, removed comment on the availability of BG Pb-Free package). *C 418633 RXU See ECN Changed status from Preliminary to Final. Changed address of Cypress Semiconductor Corporation from “3901 North First Street” to “198 Champion Court” Updated Electrical Characteristics (Updated Note 10 (Modified test condition from VDDQ < VDD to VDDQ < VDD, changed “Input Load Current except ZZ and MODE” to “Input Leakage Current except ZZ and MODE”). Updated Ordering Information (Updated part numbers, replaced Package Name column with Package Diagram in the Ordering Information table). Updated Package Diagrams (spec 51-85050 (changed revision from *A to *B)). *D 480124 VKN See ECN Updated Maximum Ratings (Added the Maximum Rating for Supply Voltage on VDDQ Relative to GND). Updated Ordering Information (Updated part numbers). *E 2756998 VKN 08/28/09 Added Neutron Soft Error Immunity. Updated Ordering Information (By including parts that are available, and modified the disclaimer for the Ordering information). *F 3036073 NJY *G 3052903 NJY *H 3208774 NJY Description of Change 09/22/2010 Added Ordering Code Definitions. Updated Package Diagrams. Added Acronyms and Units of Measure. Minor edits. Updated to new template. 10/08/10 Updated Ordering Information (Removed the following pruned part from the ordering information table namely CY7C1325G-100AXI). 03/29/2011 Updated Ordering Information (Updated part numbers). Updated Package Diagrams. Document Number: 38-05518 Rev. *P Page 22 of 24 CY7C1325G Document History Page (continued) Document Title: CY7C1325G, 4-Mbit (256 K × 18) Flow-Through Sync SRAM Document Number: 38-05518 Rev. ECN Orig. of Change Submission Date *I 3357114 PRIT 08/29/2011 Updated Package Diagrams. Completing Sunset Review. *J 3619154 PRIT 05/16/2012 Updated Features (Removed 119-ball BGA Package related information). Updated Functional Description (Removed the Note “For best practice recommendations, refer to the Cypress application note “System Design Guidelines” on www.cypress.com.” and its reference). Updated Selection Guide (Removed 100 MHz frequency related information). Updated Pin Configurations (Removed 119-ball BGA Package related information). Updated Operating Range (Removed Industrial Temperature Range). Updated Electrical Characteristics (Removed 100 MHz frequency related information). Updated Capacitance (Removed 119-ball BGA Package related information). Updated Thermal Resistance (Removed 119-ball BGA Package related information). Updated Switching Characteristics (Removed 100 MHz frequency related information). Updated Package Diagrams (Removed 119-ball BGA Package related information (spec 51-85115)). *K 3766472 PRIT 10/04/2012 No technical updates. Completing Sunset Review. *L 3980577 PRIT 04/24/2013 Added Errata. *M 4039228 PRIT 06/26/2013 Added Errata Footnotes. Updated to new template. Description of Change *N 4149237 PRIT 10/07/2013 Updated Errata. *O 4540469 PRIT 10/16/2014 Updated Package Diagrams: spec 51-85050 – Changed revision from *D to *E. *P 4574263 PRIT 11/19/2014 Added related documentation hyperlink in page 1. Completing Sunset Review. Document Number: 38-05518 Rev. *P Page 23 of 24 CY7C1325G Sales, Solutions, and Legal Information Worldwide Sales and Design Support Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office closest to you, visit us at Cypress Locations. PSoC® Solutions Products Automotive Clocks & Buffers Interface Lighting & Power Control cypress.com/go/automotive cypress.com/go/clocks cypress.com/go/interface cypress.com/go/powerpsoc cypress.com/go/plc Memory cypress.com/go/memory PSoC cypress.com/go/psoc Touch Sensing PSoC 1 | PSoC 3 | PSoC 4 | PSoC 5LP Cypress Developer Community Community | Forums | Blogs | Video | Training Technical Support cypress.com/go/support cypress.com/go/touch USB Controllers Wireless/RF psoc.cypress.com/solutions cypress.com/go/USB cypress.com/go/wireless © Cypress Semiconductor Corporation, 2004-2014. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign), United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of, and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without the express written permission of Cypress. Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Use may be limited by and subject to the applicable Cypress software license agreement. Document Number: 38-05518 Rev. *P Revised November 19, 2014 All products and company names mentioned in this document may be the trademarks of their respective holders. Page 24 of 24