PCAL9538A Low-voltage 8-bit I2C-bus and SMBus low power I/O port with interrupt, reset and Agile I/O Rev. 2 — 10 December 2012 Product data sheet 1. General description The PCAL9538A is a low-voltage 8-bit General Purpose Input/Output (GPIO) expander with interrupt and reset for I2C-bus/SMBus applications. NXP I/O expanders provide a simple solution when additional I/Os are needed while keeping interconnections to a minimum, for example, in ACPI power switches, sensors, push buttons, LEDs, fan control, etc. In addition to providing a flexible set of GPIOs, the wide VDD range of 1.65 V to 5.5 V allows the PCAL9538A to interface with next-generation microprocessors and microcontrollers where supply levels are dropping down to conserve power. The PCAL9538A contains the PCA9538A register set of four 8-bit Configuration, Input, Output, and Polarity Inversion registers, and additionally, the PCAL9538A has Agile I/O, which are additional features specifically designed to enhance the I/O. These additional features are: programmable output drive strength, latchable inputs, programmable pull-up/pull-down resistors, maskable interrupt, interrupt status register, programmable open-drain or push-pull outputs. The PCAL9538A is a pin-to-pin replacement for the PCA9538, however, the PCAL9538A powers up with all I/O interrupts masked. This mask default allows for a board bring-up free of spurious interrupts at power-up. The PCAL9538A open-drain interrupt (INT) output is activated when any input state differs from its corresponding Input Port register state and is used to indicate to the system master that an input state has changed. INT can be connected to the interrupt input of a microcontroller. By sending an interrupt signal on this line, the remote I/O can inform the microcontroller if there is incoming data on its ports without having to communicate via the I2C-bus. Thus, the PCAL9538A can remain a simple slave device. The device outputs have 25 mA sink capabilities for directly driving LEDs while consuming low device current. The power-on reset sets the registers to their default values and initializes the device state machine. In the PCAL9538A, the RESET pin causes the same reset/default I/O input configuration to occur without de-powering the device, holding the registers and I2C-bus state machine in their default state until the RESET input is once again HIGH. This input requires a pull-up to VDD. Two hardware pins (A0, A1) select the fixed I2C-bus address and allow up to four devices to share the same I2C-bus/SMBus. PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port 2. Features and benefits I2C-bus to parallel port expander Operating power supply voltage range of 1.65 V to 5.5 V Low standby current consumption: 1.5 A (typical at 5 V VDD) 1.0 A (typical at 3.3 V VDD) Schmitt-trigger action allows slow input transition and better switching noise immunity at the SCL and SDA inputs Vhys = 0.10 VDD (typical) 5 V tolerant I/Os Active LOW reset input (RESET) Open-drain active LOW interrupt output (INT) 400 kHz Fast-mode I2C-bus Internal power-on reset Power-up with all channels configured as inputs No glitch on power-up Latched outputs with 25 mA drive maximum capability for directly driving LEDs Latch-up performance exceeds 100 mA per JESD78, Class II ESD protection exceeds JESD22 2000 V Human Body Model (A114-A) 1000 V Charged-Device Model (C101) Packages offered: TSSOP16 and HVQFN16 2.1 Agile I/O features Pin to pin replacement for PCA9538 and PCA9538A with interrupts disabled at power-up Software backward compatible with PCA9539 and PCA9539A Output port configuration: bank selectable push-pull or open-drain output stages Interrupt status: read-only register identifies the source of an interrupt Bit-wise I/O programming features: Output drive strength: four programmable drive strengths to reduce rise and fall times in low capacitance applications Input latch: Input Port register values changes are kept until the Input Port register is read Pull-up/pull-down enable: floating input or pull-up/down resistor enable Pull-up/pull-down selection: 100 k pull-up/down resistor selection Interrupt mask: mask prevents the generation of the interrupt when input changes state PCAL9538A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 10 December 2012 © NXP B.V. 2012. All rights reserved. 2 of 43 PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port 3. Ordering information Table 1. Ordering information Type number Topside mark Package Name Description Version PCAL9538ABS L3A HVQFN16 plastic thermal enhanced very thin quad flat package; no leads; 16 terminals; body 3 3 0.85 mm SOT758-1 PCAL9538APW PL9538A TSSOP16 plastic thin shrink small outline package; 16 leads; body width 4.4 mm SOT403-1 3.1 Ordering options Table 2. Ordering options Type number Orderable part number Package Packing method Minimum order quantity Temperature range PCAL9538ABS PCAL9538ABSHP HVQFN16 Reel pack, SMD, 13-inch, Turned 6000 Tamb = 40 C to +85 C PCAL9538APW PCAL9538APWJ TSSOP16 Reel pack, SMD, 13-inch 2500 Tamb = 40 C to +85 C 4. Block diagram A0 A1 SCL SDA P0 P1 P2 P3 P4 P5 P6 P7 8-bit INPUT FILTER I2C-BUS/SMBus CONTROL write pulse INPUT/ OUTPUT PORTS read pulse VDD RESET POWER-ON RESET VDD PCAL9538A VSS INT LP FILTER 002aah097 Remark: All I/Os are set to inputs at reset. Fig 1. PCAL9538A Product data sheet Block diagram of PCAL9538A All information provided in this document is subject to legal disclaimers. Rev. 2 — 10 December 2012 © NXP B.V. 2012. All rights reserved. 3 of 43 PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port 5. Pinning information 4 P1 5 P2 6 11 P6 P3 7 10 P5 VSS 8 PCAL9538APW 2 13 INT 12 P7 9 13 SDA 14 VDD P1 3 10 P7 P2 4 9 P4 P6 002aah100 Transparent top view 002aah099 Fig 2. 11 INT PCAL9538ABS 8 P0 P0 P5 14 SCL 12 SCL 7 3 1 P4 RESET RESET 6 15 SDA VSS 16 VDD 2 5 1 A1 P3 A0 16 A1 terminal 1 index area 15 A0 5.1 Pinning Pin configuration for TSSOP16 Fig 3. Pin configuration for HVQFN16 5.2 Pin description Table 3. Symbol PCAL9538A Product data sheet Pin description Pin Description TSSOP16 HVQFN16 A0 1 15 address input 0 A1 2 16 address input 1 RESET 3 1 active LOW reset input P0[1] 4 2 Port P input/output 0 P1[1] 5 3 Port P input/output 1 P2[1] 6 4 Port P input/output 2 P3[1] 7 5 Port P input/output 3 VSS 8 6[2] supply ground P4[1] 9 7 Port P input/output 4 P5[1] 10 8 Port P input/output 5 P6[1] 11 9 Port P input/output 6 P7[1] 12 10 Port P input/output 7 INT 13 11 interrupt output (open-drain) SCL 14 12 serial clock line SDA 15 13 serial data line VDD 16 14 supply voltage [1] All I/O are configured as input at power-on. [2] HVQFN16 package die supply ground is connected to both the VSS pin and the exposed center pad. The VSS pin must be connected to supply ground for proper device operation. For enhanced thermal, electrical, and board-level performance, the exposed pad needs to be soldered to the board using a corresponding thermal pad on the board, and for proper heat conduction through the board thermal vias need to be incorporated in the printed-circuit board in the thermal pad region. All information provided in this document is subject to legal disclaimers. Rev. 2 — 10 December 2012 © NXP B.V. 2012. All rights reserved. 4 of 43 PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port 6. Functional description Refer to Figure 1 “Block diagram of PCAL9538A”. 6.1 Device address slave address 1 1 1 0 0 fixed A1 A0 R/W hardware selectable 002aae707 Fig 4. PCAL9538A address A1 and A0 are the hardware address package pins and are held to either HIGH (logic 1) or LOW (logic 0) to assign one of the four possible slave addresses. The last bit of the slave address (R/W) defines the operation (read or write) to be performed. A HIGH (logic 1) selects a read operation, while a LOW (logic 0) selects a write operation. 6.2 Pointer register and command byte Following the successful acknowledgement of the address byte, the bus master sends a command byte, which is stored in the Pointer register in the PCAL9538A. Two bits of this data byte state the operation (read or write) and the internal registers (Input, Output, Polarity Inversion, or Configuration) that will be affected. Bit 6 in conjunction with the lower three bits of the Command byte are used to point to the extended features of the device (Agile I/O). This register is write only. B7 B6 B5 B4 B3 B2 B1 B0 002aaf540 Fig 5. PCAL9538A Product data sheet Pointer register bits All information provided in this document is subject to legal disclaimers. Rev. 2 — 10 December 2012 © NXP B.V. 2012. All rights reserved. 5 of 43 PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port Table 4. Command byte Pointer register bits Command byte Register (hexadecimal) Protocol Power-up default B7 B6 B5 B4 B3 B2 B1 B0 0 0 0 0 0 0 0 0 00h Input port read byte xxxx xxxx[1] 0 0 0 0 0 0 0 1 01h Output port read/write byte 1111 1111 0 0 0 0 0 0 1 0 02h Polarity Inversion read/write byte 0000 0000 0 0 0 0 0 0 1 1 03h Configuration read/write byte 1111 1111 0 1 0 0 0 0 0 0 40h Output drive strength 0 read/write byte 1111 1111 0 1 0 0 0 0 0 1 41h Output drive strength 1 read/write byte 1111 1111 0 1 0 0 0 0 1 0 42h Input latch read/write byte 0000 0000 0 1 0 0 0 0 1 1 43h Pull-up/pull-down enable read/write byte 0000 0000 0 1 0 0 0 1 0 0 44h Pull-up/pull-down selection read/write byte 1111 1111 0 1 0 0 0 1 0 1 45h Interrupt mask read/write byte 1111 1111 0 1 0 0 0 1 1 0 46h Interrupt status read byte 0000 0000 0 1 0 0 0 1 1 1 47h Output port configuration read/write byte 0000 0000 [1] Undefined. 6.3 Interface definition Table 5. Interface definition Byte Bit 7 (MSB) 6 5 4 3 2 1 0 (LSB) I2C-bus slave address H H H L L A1 A0 R/W I/O data bus P7 P6 P5 P4 P3 P2 P1 P0 6.4 Register descriptions 6.4.1 Input port register (00h) The Input port register (register 0) reflects the incoming logic levels of the pins, regardless of whether the pin is defined as an input or an output by the Configuration register. The Input port register is read only; writes to this register have no effect. The default value ‘X’ is determined by the externally applied logic level. An Input port register read operation is performed as described in Section 7.2 “Read commands”. Table 6. Input port register (address 00h) Bit 7 6 5 4 3 2 1 0 Symbol I7 I6 I5 I4 I3 I2 I1 I0 Default X X X X X X X X 6.4.2 Output port register (01h) The Output port register (register 1) shows the outgoing logic levels of the pins defined as outputs by the Configuration register. Bit values in these registers have no effect on pins defined as inputs. In turn, reads from this register reflect the value that was written to this register, not the actual pin value. PCAL9538A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 10 December 2012 © NXP B.V. 2012. All rights reserved. 6 of 43 PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port Table 7. Bit Output port register (address 01h) 7 6 5 4 3 2 1 0 Symbol O7 O6 O5 O4 O3 O2 O1 O0 Default 1 1 1 1 1 1 1 1 6.4.3 Polarity inversion register (02h) The Polarity inversion register (register 2) allows polarity inversion of pins defined as inputs by the Configuration register. If a bit in this register is set (written with ‘1’), the corresponding port pin’s polarity is inverted. If a bit in this register is cleared (written with a ‘0’), the corresponding port pin’s original polarity is retained. Table 8. Bit Polarity inversion register (address 02h) 7 6 5 4 3 2 1 0 Symbol N7 N6 N5 N4 N3 N2 N1 N0 Default 0 0 0 0 0 0 0 0 6.4.4 Configuration register (03h) The Configuration register (register 3) configures the direction of the I/O pins. If a bit in this register is set to 1, the corresponding port pin is enabled as a high-impedance input. If a bit in this register is cleared to 0, the corresponding port pin is enabled as an output. Table 9. Bit Configuration register (address 03h) 7 6 5 4 3 2 1 0 Symbol C7 C6 C5 C4 C3 C2 C1 C0 Default 1 1 1 1 1 1 1 1 6.4.5 Output drive strength registers (40h, 41h) The Output drive strength registers control the output drive level of the GPIO. Each GPIO can be configured independently to a certain output current level by two register control bits. For example, Port 7 is controlled by register 41 CC7 (bits [7:6]), Port 6 is controlled by register 41 CC6 (bits [5:4]). The output drive level of the GPIO is programmed 00b = 0.25, 01b = 0.5, 10b = 0.75 or 11b = 1 of the drive capability of the I/O. See Section 8.2 “Output drive strength control” for more details. Table 10. Bit Current control register (address 40h) 7 Symbol Default Table 11. Bit 1 PCAL9538A Product data sheet 5 4 3 CC2 1 1 2 1 CC1 1 1 0 CC0 1 1 2 1 1 Current control register (address 41h) 7 Symbol Default 6 CC3 6 5 CC7 1 4 3 CC6 1 1 CC5 1 All information provided in this document is subject to legal disclaimers. Rev. 2 — 10 December 2012 1 0 CC4 1 1 1 © NXP B.V. 2012. All rights reserved. 7 of 43 PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port 6.4.6 Input latch register (42h) The Input latch register enables and disables the input latch of the I/O pins. These registers are effective only when the pin is configured as an input port. When an input latch register bit is 0, the corresponding input pin state is not latched. A state change in the corresponding input pin generates an interrupt. A read of the input port register clears the interrupt. If the input goes back to its initial logic state before the input port register is read, then the interrupt is cleared. When an input latch register bit is 1, the corresponding input pin state is latched. A change of state of the input generates an interrupt and the input logic value is loaded into the corresponding bit of the input port register (registers 0). A read of the input port register clears the interrupt. If the input pin returns to its initial logic state before the input port register is read, then the interrupt is not cleared and the corresponding bit of the input port register keeps the logic value that initiated the interrupt. See Figure 11. For example, if the P4 input was as logic 0 and the input goes to logic 1 then back to logic 0, the input port register will capture this change and an interrupt is generated (if unmasked). When the read is performed on the input port register, the interrupt is cleared, assuming there were no additional input(s) that have changed, and bit 4 of the input port register will read ‘1’. The next read of the input port register bit 4 should now read ‘0’. An interrupt remains active when a non-latched input simultaneously switches state with a latched input and then returns to its original state. A read of the input port register reflects only the change of state of the latched input and also clears the interrupt. The interrupt is not cleared if the input latch register changes from latched to non-latched configuration. If the input pin is changed from latched to non-latched input, a read from the input port register reflects the current port logic level. If the input pin is changed from non-latched to latched input, the read from the input port register reflects the latched logic level. Table 12. Input latch register (address 42h) Bit 7 6 5 4 3 2 1 0 Symbol L7 L6 L5 L4 L3 L2 L1 L0 Default 0 0 0 0 0 0 0 0 6.4.7 Pull-up/pull-down enable register (43h) This register allows the user to enable or disable pull-up/pull-down resistors on the I/O pins. Setting the bit to logic 1 enables the selection of pull-up/pull-down resistors. Setting the bit to logic 0 disconnects the pull-up/pull-down resistors from the I/O pins. Use the pull-up/pull-down registers to select either a pull-up or pull-down resistor. Table 13. Bit PCAL9538A Product data sheet Pull-up/pull-down enable register (address 43h) 7 6 5 4 3 2 1 0 Symbol PE7 PE6 PE5 PE4 PE3 PE2 PE1 PE0 Default 0 0 0 0 0 0 0 0 All information provided in this document is subject to legal disclaimers. Rev. 2 — 10 December 2012 © NXP B.V. 2012. All rights reserved. 8 of 43 PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port 6.4.8 Pull-up/pull-down selection register (44h) The I/O port can be configured to have pull-up or pull-down resistor by programming the pull-up/pull-down selection register. Setting a bit to logic 1 selects a 100 k pull-up resistor for that I/O pin. Setting a bit to logic 0 selects a 100 k pull-down resistor for that I/O pin. If the pull-up/down feature is disconnected, writing to this register will have no effect on I/O pin. Typical value is 100 k with minimum of 50 k and maximum of 150 k. Table 14. Bit Pull-up/pull-down selection register (address 44h) 7 6 5 4 3 2 1 0 Symbol PUD7 PUD6 PUD5 PUD4 PUD3 PUD2 PUD1 PUD0 Default 1 1 1 1 1 1 1 1 6.4.9 Interrupt mask register (45h) Interrupt mask register is set to logic 1 upon power-on, disabling interrupts during system start-up. Interrupts may be enabled by setting corresponding mask bits to logic 0. If an input changes state and the corresponding bit in the Interrupt mask register is set to 1, the interrupt is masked and the interrupt pin (INT) will not be asserted. If the corresponding bit in the Interrupt mask register is set to 0, the interrupt pin will be asserted. When an input changes state and the resulting interrupt is masked (interrupt mask bit is 1), setting the input mask register bit to 0 will cause the interrupt pin to be asserted. If the interrupt mask bit of an input that is currently the source of an interrupt is set to 1, the interrupt pin will be de-asserted. Table 15. Bit Interrupt mask register (address 45h) 7 6 5 4 3 2 1 0 Symbol M7 M6 M5 M4 M3 M2 M1 M0 Default 1 1 1 1 1 1 1 1 6.4.10 Interrupt status register (46h) This read-only register is used to identify the source of an interrupt. When read, a logic 1 indicates that the corresponding input pin was the source of the interrupt. A logic 0 indicates that the input pin is not the source of an interrupt. When a corresponding bit in the interrupt mask register is set to 1 (masked), the interrupt status bit will return logic 0. Table 16. Bit PCAL9538A Product data sheet Interrupt status register (address 46h) 7 6 5 4 3 2 1 0 Symbol S7 S6 S5 S4 S3 S2 S1 S0 Default 0 0 0 0 0 0 0 0 All information provided in this document is subject to legal disclaimers. Rev. 2 — 10 December 2012 © NXP B.V. 2012. All rights reserved. 9 of 43 PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port 6.4.11 Output port configuration register (47h) The output port configuration register selects port-wise push-pull or open-drain I/O stage. A logic 0 configures the I/O as push-pull (Q1 and Q2 are active, see Figure 6). A logic 1 configures the I/O as open-drain (Q1 is disabled, Q2 is active). Table 17. Output port configuration register (address 47h) Bit 7 6 5 4 Symbol 3 2 1 0 reserved Default 0 0 0 0 ODEN0 0 0 0 0 6.5 I/O port When an I/O is configured as an input, FETs Q1 and Q2 are off, which creates a high-impedance input. The input voltage may be raised above VDD to a maximum of 5.5 V. If the I/O is configured as an output, Q1 or Q2 is enabled, depending on the state of the Output port register. In this case, there are low-impedance paths between the I/O pin and either VDD or VSS. The external voltage applied to this I/O pin should not exceed the recommended levels for proper operation. data from shift register output port register data configuration register data from shift register D write configuration pulse CK VDD Q Q1 ESD protection diode Q2 ESD protection diode FF Q D Q P0 to P7 FF write pulse CK output port register VSS D Q input port register data FF read pulse CK VDD PULL-UP/PULL-DOWN CONTROL INTERRUPT MASK input port register 100 kΩ D input latch register data from shift register D data from shift register CK Q LATCH Q read pulse FF write input latch pulse to INT polarity inversion register D EN input port latch Q FF write polarity pulse CK 002aah101 On power-up or reset, all registers return to default values. Fig 6. PCAL9538A Product data sheet Simplified schematic of the I/Os (P0 to P7) All information provided in this document is subject to legal disclaimers. Rev. 2 — 10 December 2012 © NXP B.V. 2012. All rights reserved. 10 of 43 PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port 6.6 Power-on reset When power (from 0 V) is applied to VDD, an internal power-on reset holds the PCAL9538A in a reset condition until VDD has reached VPOR. At that time, the reset condition is released and the PCAL9538A registers and I2C-bus/SMBus state machine initialize to their default states. After that, VDD must be lowered to below VPOR and back up to the operating voltage for a power-reset cycle. See Section 8.4 “Power-on reset requirements”. 6.7 Reset input (RESET) The RESET input can be asserted to initialize the system while keeping the VDD at its operating level. A reset can be accomplished by holding the RESET pin LOW for a minimum of tw(rst). The PCAL9538A registers and I2C-bus/SMBus state machine are changed to their default state once RESET is LOW (0). When RESET is HIGH (1), the I/O levels at the P port can be changed externally or through the master. This input requires a pull-up resistor to VDD if no active connection is used. 6.8 Interrupt output (INT) An interrupt is generated by any rising or falling edge of the port inputs in the Input mode. After time tv(INT), the signal INT is valid. Resetting the interrupt circuit is achieved when data on the port is changed to the original setting or when data is read from the port that generated the interrupt (see Figure 10). Resetting occurs in the Read mode at the acknowledge (ACK) or not acknowledge (NACK) bit after the rising edge of the SCL signal. Interrupts that occur during the ACK or NACK clock pulse can be lost (or be very short) due to the resetting of the interrupt during this pulse. Each change of the I/Os after resetting is detected and is transmitted as INT. A pin configured as an output cannot cause an interrupt. Changing an I/O from an output to an input may cause a false interrupt to occur, if the state of the pin does not match the contents of the Input port register. The INT output has an open-drain structure and requires a pull-up resistor to VDD. INT should be connected to the voltage source of the device that requires the interrupt information. When using the input latch feature, the input pin state is latched. The interrupt is reset only when data is read from the port that generated the interrupt. The reset occurs in the Read mode at the acknowledge (ACK) or not acknowledge (NACK) bit after the rising edge of the SCL signal. PCAL9538A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 10 December 2012 © NXP B.V. 2012. All rights reserved. 11 of 43 PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port 7. Bus transactions The PCAL9538A is an I2C-bus slave device. Data is exchanged between the master and PCAL9538A through write and read commands using I2C-bus. The two communication lines are a serial data line (SDA) and a serial clock line (SCL). Both lines must be connected to a positive supply via a pull-up resistor when connected to the output stages of a device. Data transfer may be initiated only when the bus is not busy. 7.1 Write commands Data is transmitted to the PCAL9538A by sending the device address and setting the Least Significant Bit (LSB) to a logic 0 (see Figure 4 for device address). The command byte is sent after the address and determines which register receives the data that follows the command byte. There is no limitation on the number of data bytes sent in one write transmission. SCL 1 2 3 4 5 6 7 8 9 slave address 1 0 0 A1 A0 0 START condition R/W SDA S 1 1 A 0 0 0 0 0 0 STOP condition data to port command byte 0 acknowledge from slave 1 A DATA 1 A P acknowledge from slave acknowledge from slave write to port tv(Q) data out from port DATA 1 VALID 002aah102 Fig 7. Write to Output port register SCL 1 2 3 4 5 6 7 8 9 slave address 0 0 A1 A0 0 START condition R/W SDA S 1 1 1 A 0 1/0 1/0 0 1/0 1/0 1/0 1/0 A acknowledge from slave STOP condition data to register command byte acknowledge from slave DATA 1 A P acknowledge from slave 002aah103 Fig 8. Write to Configuration or Polarity inversion registers PCAL9538A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 10 December 2012 © NXP B.V. 2012. All rights reserved. 12 of 43 PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port 7.2 Read commands To read data from the PCAL9538A, the bus master must first send the PCAL9538A address with the least significant bit set to a logic 0 (see Figure 4 for device address). The command byte is sent after the address and determines which register is to be accessed. After a restart the device address is sent again, but this time the LSB is set to a logic 1. Data from the register defined by the command byte then is sent by the PCAL9538A (see Figure 9 and Figure 10). Data is clocked into the register on the rising edge of the ACK clock pulse. There is no limit on the number of data bytes received in one read transmission, but on the final byte received the bus master must not acknowledge the data. slave address SDA S 1 1 1 0 0 A1 A0 0 START condition A R/W slave address 1 1 1 0 Fig 9. data from register 0 A1 A0 1 (repeated) START condition (cont.) acknowledge from slave acknowledge from slave (cont.) S A COMMAND BYTE A DATA (first byte) R/W data from register A DATA (last byte) acknowledge from master acknowledge from slave NA P STOP condition no acknowledge from master at this moment master-transmitter becomes master-receiver and slave-receiver becomes slave-transmitter 002aah104 Read from register SCL 1 2 3 4 5 6 7 8 9 slave address SDA S 1 1 1 data from port 0 0 A1 A0 1 START condition R/W DATA 1 A data from port A acknowledge from slave DATA 4 acknowledge from master read from port data into port DATA 1 DATA 2 th(D) DATA 3 tsu(D) INT tv(INT) trst(INT) DATA 4 no acknowledge from master 1 P STOP condition DATA 5 INT is cleared by read from port STOP not needed to clear INT 002aah105 Transfer of data can be stopped at any time by a STOP condition. When this occurs, data present at the latest acknowledge phase is valid (output mode). It is assumed that the command byte has previously been programmed with 00h (read Input port register). This figure eliminates the command byte transfer, a restart, and slave address call between the initial slave address call and actual data transfer from P port (see Figure 9). Fig 10. Read Input port register (non-latched) PCAL9538A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 10 December 2012 © NXP B.V. 2012. All rights reserved. 13 of 43 PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port SCL 1 2 3 4 5 6 7 8 9 slave address SDA S 1 1 1 data from port 0 0 A1 A0 1 START condition R/W DATA 1 A data from port A acknowledge from slave DATA 2 acknowledge from master read from port data into port DATA 1 tsu(D) INT tv(INT) 1 P STOP condition DATA 1 DATA 2 th(D) no acknowledge from master trst(INT) INT is cleared by read from port STOP not needed to clear INT 002aah106 Transfer of data can be stopped at any time by a STOP condition. When this occurs, data present at the latest acknowledge phase is valid (output mode). It is assumed that the command byte has previously been programmed with 00h (read Input port register). This figure eliminates the command byte transfer, a restart, and slave address call between the initial slave address call and actual data transfer from P port (see Figure 9). Fig 11. Read Input port register (latch enabled) PCAL9538A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 10 December 2012 © NXP B.V. 2012. All rights reserved. 14 of 43 PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port 8. Application design-in information VDD (3.3 V) 10 kΩ 10 kΩ 10 kΩ 10 kΩ 2 kΩ VDD VDD MASTER CONTROLLER PCAL9538A SCL SCL P0 SDA P1 INT INT RESET SUB-SYSTEM 2 (e.g., counter) P2 RESET P3 VSS SUB-SYSTEM 1 (e.g., temp sensor) INT SDA RESET 100 kΩ (× 3)(1) P4 A controlled switch (e.g., CBT device) enable P5 A1 P6 A0 P7 VSS B SUB-SYSTEM 3 (e.g., alarm system) ALARM VDD 002aah107 Device address is 1110 000x for this example. P0, P2, P3 configured as outputs. P1, P4, P5 configured as inputs. P6, P7 are not used and need 100 k pull-up resistors to protect them from floating or the internal pull-up or pull-down selected. (1) Resistors are required for inputs (on P port) that may float. If a driver to an input will never let the input float, a resistor is not needed. Outputs (in the P port) do not need pull-up resistors. Fig 12. Typical application 8.1 Minimizing IDD when the I/Os are used to control LEDs When the I/Os are used to control LEDs, they are normally connected to VDD through a resistor as shown in Figure 12. Since the LED acts as a diode, when the LED is off the I/O VI is about 1.2 V less than VDD. The supply current, IDD, increases as VI becomes lower than VDD. Designs needing to minimize current consumption, such as battery power applications, should consider maintaining the I/O pins greater than or equal to VDD when the LED is off. Figure 13 shows a high value resistor in parallel with the LED. Figure 14 shows VDD less than the LED supply voltage by at least 1.2 V. Both of these methods maintain the I/O VI at or above VDD and prevents additional supply current consumption when the LED is off. PCAL9538A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 10 December 2012 © NXP B.V. 2012. All rights reserved. 15 of 43 PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port 3.3 V VDD VDD LED 5V VDD 100 kΩ LED Pn Pn 002aag164 Fig 13. High value resistor in parallel with the LED 002aag165 Fig 14. Device supplied by a lower voltage 8.2 Output drive strength control The Output drive strength registers allow the user to control the output drive level of the GPIO. Each GPIO can be configured independently to one of the four possible output current levels. By programming these bits the user is changing the number of transistor pairs or ‘fingers’ that drive the I/O pad. Figure 15 shows a simplified output stage. The behavior of the pad is affected by the Configuration register, the output port data, and the current control register. When the Current Control register bits are programmed to 10b, then only two of the fingers are active, reducing the current drive capability by 50 %. PMOS_EN0 VDD PMOS_EN1 Current Control register PMOS_EN[3:0] DECODER NMOS_EN[3:0] PMOS_EN2 Configuration register PMOS_EN3 P0 to P7 Output port register NMOS_EN3 NMOS_EN2 NMOS_EN1 NMOS_EN0 002aah108 Fig 15. Simplified output stage PCAL9538A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 10 December 2012 © NXP B.V. 2012. All rights reserved. 16 of 43 PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port Reducing the current drive capability may be desirable to reduce system noise. When the output switches (transitions from H/L), there is a peak current that is a function of the output drive selection. This peak current runs through VDD and VSS package inductance and will create noise (some radiated, but more critically Simultaneous Switching Noise (SSN)). In other words, switching many outputs at the same time will create ground and supply noise. The output drive strength control through the Current Control registers allows the user to mitigate SSN issues without the need of additional external components. 8.3 12 V tolerant I/Os The PCAL9538A device SCR group reference diode can go up to 10 V before latch back to 8 V. The ESD gate oxide will protect the device, but not if used continually. Therefore, to achieve 12 V tolerant I/Os, the external protection circuitry (diode) must be used as shown in Figure 16. +5 V A0 VDD A1 SDA RESET SCL P0 P1 PCAL9538A +12 V INT P2 P7 P6 P3 P5 VSS P4 002aah109 Fig 16. External protection circuitry PCAL9538A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 10 December 2012 © NXP B.V. 2012. All rights reserved. 17 of 43 PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port 8.4 Power-on reset requirements In the event of a glitch or data corruption, PCAL9538A can be reset to its default conditions by using the power-on reset feature. Power-on reset requires that the device go through a power cycle to be completely reset. This reset also happens when the device is powered on for the first time in an application. The two types of power-on reset are shown in Figure 17 and Figure 18. VDD ramp-up ramp-down re-ramp-up td(rst) time (dV/dt)r (dV/dt)f time to re-ramp when VDD drops below 0.2 V or to VSS (dV/dt)r 002aah329 Fig 17. VDD is lowered below 0.2 V or 0 V and then ramped up to VDD VDD ramp-down ramp-up td(rst) VI drops below POR levels (dV/dt)f time time to re-ramp when VDD drops to VPOR(min) − 50 mV (dV/dt)r 002aah330 Fig 18. VDD is lowered below the POR threshold, then ramped back up to VDD Table 18 specifies the performance of the power-on reset feature for PCAL9538A for both types of power-on reset. Table 18. Recommended supply sequencing and ramp rates Tamb = 25 C (unless otherwise noted). Not tested; specified by design. Symbol Parameter Condition Min Typ Max Unit (dV/dt)f fall rate of change of voltage Figure 17 0.1 - 2000 ms (dV/dt)r rise rate of change of voltage Figure 17 0.1 - 2000 ms td(rst) reset delay time Figure 17; re-ramp time when VDD drops to VSS 1 - - s Figure 18; re-ramp time when VDD drops to VPOR(min) 50 mV 1 - - s VDD(gl) glitch supply voltage difference Figure 19 [1] - - 1.0 V [2] - - 10 s tw(gl)VDD supply voltage glitch pulse width Figure 19 VPOR(trip) power-on reset trip voltage falling VDD 0.7 - - V rising VDD - - 1.4 V [1] Level that VDD can glitch down to, but not cause a functional disruption when tw(gl)VDD < 1 s. [2] Glitch width that will not cause a functional disruption when VDD(gl) = 0.5 VDD. PCAL9538A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 10 December 2012 © NXP B.V. 2012. All rights reserved. 18 of 43 PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port Glitches in the power supply can also affect the power-on reset performance of this device. The glitch width (tw(gl)VDD) and glitch height (VDD(gl)) are dependent on each other. The bypass capacitance, source impedance, and device impedance are factors that affect power-on reset performance. Figure 19 and Table 18 provide more information on how to measure these specifications. VDD ∆VDD(gl) tw(gl)VDD time 002aah331 Fig 19. Glitch width and glitch height VPOR is critical to the power-on reset. VPOR is the voltage level at which the reset condition is released and all the registers and the I2C-bus/SMBus state machine are initialized to their default states. The value of VPOR differs based on the VDD being lowered to or from 0 V. Figure 20 and Table 18 provide more details on this specification. VDD VPOR (rising VDD) VPOR (falling VDD) time POR time 002aah332 Fig 20. Power-on reset voltage (VPOR) PCAL9538A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 10 December 2012 © NXP B.V. 2012. All rights reserved. 19 of 43 PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port 8.5 Device current consumption with internal pull-up and pull-down resistors The PCAL9538A integrates programmable pull-up and pull-down resistors to eliminate external components when pins are configured as inputs and pull-up or pull-down resistors are required (for example, nothing is driving the inputs to the power supply rails. Since these pull-up and pull-down resistors are internal to the device itself, they contribute to the current consumption of the device and must be considered in the overall system design. The pull-up or pull-down function is selected in register 44h, while the resistor is connected by the enable register 43h. The configuration of the resistors is shown in Figure 6. If the resistor is configured as a pull-up, that is, connected to VDD, a current will flow from the VDD pin through the resistor to ground when the pin is held LOW. This current will appear as additional IDD upsetting any current consumption measurements. In the same manner, if the resistor is configured as a pull-down and the pin is held HIGH, current will flow from the power supply through the pin to the VSS pin. While this current will not be measured as part of IDD, one must be mindful of the 200 mA limiting value through VSS. The pull-up and pull-down resistors are simple resistors and the current is linear with voltage. The resistance specification for these devices spans from 50 k with a nominal 100 k value. Any current flow through these resistors is additive by the number of pins held HIGH or LOW and the current can be calculated by Ohm’s law. See Figure 24 for a graph of supply current versus the number of pull-up resistors. PCAL9538A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 10 December 2012 © NXP B.V. 2012. All rights reserved. 20 of 43 PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port 9. Limiting values Table 19. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol Parameter VDD supply voltage Conditions Min Max Unit 0.5 +6.5 V 0.5 +6.5 V 0.5 +6.5 V VI input voltage [1] VO output voltage [1] IIK input clamping current A0, A1, RESET, SCL; VI < 0 V - 20 mA IOK output clamping current INT; VO < 0 V - 20 mA IIOK input/output clamping current P port; VO < 0 V or VO > VDD - 20 mA SDA; VO < 0 V or VO > VDD - 20 mA continuous; I/O port - 50 mA continuous; SDA, INT - 25 mA continuous; P port LOW-level output current IOL IOH HIGH-level output current - 25 mA IDD supply current - 160 mA ISS ground supply current - 200 mA Ptot total power dissipation - 200 mW Tstg storage temperature 65 +150 C Tj(max) maximum junction temperature - 125 C [1] The input negative-voltage and output voltage ratings may be exceeded if the input and output current ratings are observed. 10. Recommended operating conditions Table 20. Operating conditions Symbol Parameter Conditions Min Max Unit VDD supply voltage 1.65 5.5 V VIH HIGH-level input voltage SCL, SDA, RESET 0.7 VDD 5.5 V A0, A1, P port 0.7 VDD 5.5 V VIL LOW-level input voltage SCL, SDA, RESET 0.5 0.3 VDD V A0, A1, P port 0.5 0.3 VDD V P port - 10 mA IOH HIGH-level output current IOL LOW-level output current P port - 25 mA Tamb ambient temperature operating in free air 40 +85 C 11. Thermal characteristics Table 21. Symbol Zth(j-a) [1] Thermal characteristics Parameter Conditions transient thermal impedance from junction to ambient Max Unit HVQFN16 package [1] 53 K/W TSSOP16 package [1] 108 K/W The package thermal impedance is calculated in accordance with JESD 51-7. PCAL9538A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 10 December 2012 © NXP B.V. 2012. All rights reserved. 21 of 43 PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port 12. Static characteristics Table 22. Static characteristics Tamb = 40 C to +85 C; VDD = 1.65 V to 5.5 V; unless otherwise specified. Symbol Parameter Conditions Min Typ[1] Max Unit VIK input clamping voltage II = 18 mA 1.2 - - V VPOR power-on reset voltage VI = VDD or VSS; IO = 0 mA - 1.1 1.4 V VOH HIGH-level output voltage[2] P port; IOH = 8 mA; CCX = 11b VDD = 1.65 V 1.2 - - V VDD = 2.3 V 1.8 - - V VDD = 3 V 2.6 - - V VDD = 4.5 V 4.1 - - V VDD = 1.65 V 1.1 - - V VDD = 2.3 V 1.7 - - V VDD = 3 V 2.5 - - V VDD = 4.5 V 4.0 - - V VDD = 1.65 V - - 0.45 V VDD = 2.3 V - - 0.25 V VDD = 3 V - - 0.25 V VDD = 4.5 V - - 0.2 V VDD = 1.65 V - - 0.5 V VDD = 2.3 V - - 0.3 V VDD = 3 V - - 0.25 V VDD = 4.5 V - - 0.2 V SDA 3 - - mA INT 3 15[3] - mA - - 0.1 A P port; IOH = 2.5 mA and CCX = 00b; IOH = 5 mA and CCX = 01b; IOH = 7.5 mA and CCX = 10b; IOH = 10 mA and CCX = 11b VOL LOW-level output voltage[2] P port; IOL = 8 mA; CCX = 11b P port; IOL = 2.5 mA and CCX = 00b; IOL = 5 mA and CCX = 01b; IOL = 7.5 mA and CCX = 10b; IOL = 10 mA and CCX = 11b IOL II LOW-level output current input current VOL = 0.4 V; VDD = 1.65 V to 5.5 V VDD = 1.65 V to 5.5 V SCL, SDA, RESET; VI = VDD or VSS - - 1 A IIH HIGH-level input current P port; VI = VDD; VDD = 1.65 V to 5.5 V - - 1 A IIL LOW-level input current P port; VI = VSS; VDD = 1.65 V to 5.5 V - - 1 A A0, A1; VI = VDD or VSS PCAL9538A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 10 December 2012 © NXP B.V. 2012. All rights reserved. 22 of 43 PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port Table 22. Static characteristics …continued Tamb = 40 C to +85 C; VDD = 1.65 V to 5.5 V; unless otherwise specified. Min Typ[1] Max Unit VDD = 3.6 V to 5.5 V - 10 25 A VDD = 2.3 V to 3.6 V - 6.5 15 A VDD = 1.65 V to 2.3 V - 4 9 A VDD = 3.6 V to 5.5 V - 1.5 7 A VDD = 2.3 V to 3.6 V - 1 3.2 A VDD = 1.65 V to 2.3 V - 0.5 1.7 A SCL, SDA, RESET; one input at VDD 0.6 V, other inputs at VDD or VSS; VDD = 1.65 V to 5.5 V - - 25 A P port, A0, A1; one input at VDD 0.6 V, other inputs at VDD or VSS; VDD = 1.65 V to 5.5 V - - 80 A Symbol Parameter Conditions IDD supply current SDA, P port, A0, A1, RESET; VI on SDA and RESET = VDD or VSS; VI on P port and A0, A1 = VDD; IO = 0 mA; I/O = inputs; fSCL = 400 kHz SCL, SDA, P port, A0, A1, RESET; VI on SCL, SDA and RESET = VDD or VSS; VI on P port and A0, A1 = VDD; IO = 0 mA; I/O = inputs; fSCL = 0 kHz IDD additional quiescent supply current Ci input capacitance VI = VDD or VSS; VDD = 1.65 V to 5.5 V - 6 7 pF Cio input/output capacitance VI/O = VDD or VSS; VDD = 1.65 V to 5.5 V - 7 8 pF VI/O = VDD or VSS; VDD = 1.65 V to 5.5 V - 7.5 8.5 pF Rpu(int) internal pull-up resistance input/output 50 100 150 k Rpd(int) internal pull-down resistance input/output 50 100 150 k [1] For IDD, all typical values are at nominal supply voltage (1.8 V, 2.5 V, 3.3 V, 3.6 V or 5 V VDD) and Tamb = 25 C. Except for IDD, the typical values are at VDD = 3.3 V and Tamb = 25 C. [2] The total current sourced by all I/Os must be limited to 160 mA, and total current sunk by all I/Os must be limited to 200 mA. [3] Typical value for Tamb = 25 C. VOL = 0.4 V and VDD = 3.3 V. Typical value for VDD < 2.5 V, VOL = 0.6 V. PCAL9538A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 10 December 2012 © NXP B.V. 2012. All rights reserved. 23 of 43 PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port 12.1 Typical characteristics 002aah333 20 IDD (μA) 16 12 002aah334 1400 IDD(stb) (nA) VDD = 5.5 V 5.0 V 3.6 V 3.3 V 2.5 V 2.3 V VDD = 5.5 V 5.0 V 3.6 V 3.3 V 1000 800 600 8 400 2.5 V 2.3 V 1.8 V 1.65 V 4 0 −40 200 VDD = 1.8 V 1.65 V −15 10 35 0 −40 60 85 Tamb (°C) Fig 21. Supply current versus ambient temperature 002aah335 20 IDD (μA) 16 −15 10 35 60 85 Tamb (°C) Fig 22. Standby supply current versus ambient temperature 002aah436 600 Tamb = −40 °C 25 °C 85 °C IDD (μA) 400 12 8 200 4 0 1.5 0 2.5 3.5 4.5 5.5 0 VDD (V) Tamb = 25 C Product data sheet 4 6 8 number of I/O held LOW VDD = 5 V Fig 23. Supply current versus supply voltage PCAL9538A 2 Fig 24. Supply current versus number of I/O held LOW All information provided in this document is subject to legal disclaimers. Rev. 2 — 10 December 2012 © NXP B.V. 2012. All rights reserved. 24 of 43 PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port Isink (mA) 002aaf578 35 Isink (mA) 30 Tamb = −40 °C 25 °C 85 °C 25 002aaf579 35 30 Tamb = −40 °C 25 °C 85 °C 25 20 20 15 15 10 10 5 5 0 0 0 0.1 0.2 0.3 0 0.1 0.2 VOL (V) a. VDD = 1.65 V Isink (mA) b. VDD = 1.8 V 002aaf580 50 002aaf581 60 Isink (mA) 40 Tamb = −40 °C 25 °C 85 °C 30 0.3 VOL (V) Tamb = −40 °C 25 °C 85 °C 40 20 20 10 0 0 0 0.1 0.2 0.3 0 0.1 0.2 VOL (V) c. VDD = 2.5 V Isink (mA) 0.3 VOL (V) d. VDD = 3.3 V 002aaf582 70 Isink (mA) Tamb = −40 °C 25 °C 85 °C 60 50 002aaf583 70 Tamb = −40 °C 25 °C 85 °C 60 50 40 40 30 30 20 20 10 10 0 0 0 0.1 0.2 0.3 0 VOL (V) e. VDD = 5.0 V 0.1 0.2 0.3 VOL (V) f. VDD = 5.5 V Fig 25. I/O sink current versus LOW-level output voltage with CCX.X = 11b PCAL9538A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 10 December 2012 © NXP B.V. 2012. All rights reserved. 25 of 43 PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port 002aah110 30 Isource (mA) Isource (mA) Tamb = −40 °C 25 °C 85 °C 20 002aah111 35 Tamb = −40 °C 25 °C 85 °C 30 25 20 15 10 10 5 0 0 0 0.2 0.4 0.6 VDD − VOH (V) a. VDD = 1.65 V 0 002aah112 Isource (mA) Tamb = −40 °C 25 °C 85 °C 40 0.4 0.6 VDD − VOH (V) b. VDD = 1.8 V 60 Isource (mA) 0.2 002aah113 70 Tamb = −40 °C 25 °C 85 °C 60 50 40 30 20 20 10 0 0 0 0.2 0.4 0.6 VDD − VOH (V) c. VDD = 2.5 V 002aah114 0.4 0.6 VDD − VOH (V) 002aah115 90 Isource (mA) Tamb = −40 °C 25 °C 85 °C 60 0.2 d. VDD = 3.3 V 90 Isource (mA) 0 Tamb = −40 °C 25 °C 85 °C 60 30 30 0 0 0 e. VDD = 5.0 V 0.2 0.4 0.6 VDD − VOH (V) 0 0.2 0.4 0.6 VDD − VOH (V) f. VDD = 5.5 V Fig 26. I/O source current versus HIGH-level output voltage with CCX.X = 11b PCAL9538A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 10 December 2012 © NXP B.V. 2012. All rights reserved. 26 of 43 PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port VOL (mV) 002aah056 120 100 002aah343 200 VDD − VOH (mV) 160 (1) 80 120 VDD = 1.8 V 5V 60 (2) 80 40 (4) 20 0 −40 40 (3) −15 10 35 60 85 Tamb (°C) 0 −40 −15 10 35 60 85 Tamb (°C) Isource = 10 mA (1) VDD = 1.8 V; Isink = 10 mA (2) VDD = 5 V; Isink = 10 mA (3) VDD = 1.8 V; Isink = 1 mA (4) VDD = 5 V; Isink = 1 mA Fig 27. LOW-level output voltage versus temperature PCAL9538A Product data sheet Fig 28. I/O high voltage versus temperature All information provided in this document is subject to legal disclaimers. Rev. 2 — 10 December 2012 © NXP B.V. 2012. All rights reserved. 27 of 43 PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port 13. Dynamic characteristics Table 23. I2C-bus interface timing requirements Over recommended operating free air temperature range, unless otherwise specified. See Figure 29. Symbol Parameter Conditions Standard-mode I2C-bus Fast-mode I2C-bus Unit Min Max Min Max fSCL SCL clock frequency 0 100 0 400 tHIGH HIGH period of the SCL clock 4 - 0.6 - s tLOW LOW period of the SCL clock 4.7 - 1.3 - s tSP pulse width of spikes that must be suppressed by the input filter 0 50 0 50 ns tSU;DAT data set-up time 250 - 100 - ns tHD;DAT data hold time 0 - 0 - ns kHz tr rise time of both SDA and SCL signals - 1000 20 300 ns tf fall time of both SDA and SCL signals - 300 20 (VDD / 5.5 V) 300 ns tBUF bus free time between a STOP and START condition 4.7 - 1.3 - s tSU;STA set-up time for a repeated START condition 4.7 - 0.6 - s tHD;STA hold time (repeated) START condition 4 - 0.6 - s tSU;STO set-up time for STOP condition 4 - 0.6 - s tVD;DAT data valid time SCL LOW to SDA output valid - 3.45 - 0.9 s tVD;ACK data valid acknowledge time ACK signal from SCL LOW to SDA (out) LOW - 3.45 - 0.9 s Table 24. Reset timing requirements Over recommended operating free air temperature range, unless otherwise specified. See Figure 32. Symbol Parameter tw(rst) reset pulse width trec(rst) reset recovery time trst reset time [1] Conditions Standard-mode I2C-bus [1] Fast-mode I2C-bus Unit Min Max Min Max 30 - 30 - ns 200 - 200 - ns 600 - 600 - ns Minimum time for SDA to become HIGH or minimum time to wait before doing a START. PCAL9538A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 10 December 2012 © NXP B.V. 2012. All rights reserved. 28 of 43 PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port Table 25. Switching characteristics Over recommended operating free air temperature range; CL 100 pF; unless otherwise specified. See Figure 29. Symbol Parameter Conditions Standard-mode I2C-bus Fast-mode I2C-bus Min Max Min Max Unit tv(INT) valid time on pin INT from P port to INT - 1 - 1 s trst(INT) reset time on pin INT from SCL to INT - 1 - 1 s tv(Q) data output valid time from SCL to P port - 400 - 400 ns tsu(D) data input set-up time from P port to SCL 0 - 0 - ns th(D) data input hold time from P port to SCL 300 - 300 - ns 14. Parameter measurement information VDD RL = 1 kΩ DUT SDA CL = 50 pF 002aag803 a. SDA load configuration two bytes for read Input port register(1) STOP START condition condition (P) (S) Address Bit 7 (MSB) Address Bit 1 R/W Bit 0 (LSB) Data Bit 7 (MSB) ACK (A) Data Bit 0 (LSB) STOP condition (P) 002aag952 b. Transaction format tHIGH tLOW tSP 0.7 × VDD 0.3 × VDD SCL tBUF tVD;DAT tr tf tf(o) tVD;ACK tSU;STA 0.7 × VDD SDA tf tHD;STA tr 0.3 × VDD tVD;ACK tSU;DAT tSU;STO tHD;DAT repeat START condition STOP condition 002aag804 c. Voltage waveforms CL includes probe and jig capacitance. All inputs are supplied by generators having the following characteristics: PRR 10 MHz; Zo = 50 ; tr/tf 30 ns. All parameters and waveforms are not applicable to all devices. Byte 1 = I2C-bus address; Byte 2, byte 3 = P port data. (1) See Figure 9. Fig 29. I2C-bus interface load circuit and voltage waveforms PCAL9538A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 10 December 2012 © NXP B.V. 2012. All rights reserved. 29 of 43 PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port VDD RL = 4.7 kΩ INT DUT CL = 100 pF 002aah069 a. Interrupt load configuration acknowledge from slave START condition R/W 8 bits (one data byte) from port slave address SDA S SCL 1 1 1 1 2 3 0 4 0 A1 A0 1 5 6 7 8 acknowledge from slave DATA 1 A no acknowledge from master STOP condition data from port A DATA 2 1 P 9 B trst(INT) B trst(INT) INT tv(INT) data into port A A tsu(D) ADDRESS INT DATA 1 SCL 0.5 × VDD DATA 2 R/W 0.3 × VDD tv(INT) trst(INT) 0.5 × VDD Pn 0.7 × VDD A 0.5 × VDD INT View A - A View B - B 002aah116 b. Voltage waveforms CL includes probe and jig capacitance. All inputs are supplied by generators having the following characteristics: PRR 10 MHz; Zo = 50 ; tr/tf 30 ns. All parameters and waveforms are not applicable to all devices. Fig 30. Interrupt load circuit and voltage waveforms PCAL9538A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 10 December 2012 © NXP B.V. 2012. All rights reserved. 30 of 43 PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port 500 Ω Pn DUT 2 × VDD CL = 50 pF 500 Ω 002aag805 a. P port load configuration SCL P0 A P7 0.7 × VDD 0.3 × VDD SDA tv(Q) Pn unstable data last stable bit A P7 002aag806 b. Write mode (R/W = 0) SCL P0 0.7 × VDD 0.3 × VDD tsu(D) th(D) Pn 002aag807 c. Read mode (R/W = 1) CL includes probe and jig capacitance. tv(Q) is measured from 0.7 VDD on SCL to 50 % I/O (Pn) output. All inputs are supplied by generators having the following characteristics: PRR 10 MHz; Zo = 50 ; tr/tf 30 ns. The outputs are measured one at a time, with one transition per measurement. All parameters and waveforms are not applicable to all devices. Fig 31. P port load circuit and voltage waveforms PCAL9538A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 10 December 2012 © NXP B.V. 2012. All rights reserved. 31 of 43 PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port VDD RL = 1 kΩ SDA DUT 500 Ω Pn DUT CL = 50 pF 2 × VDD CL = 50 pF 500 Ω 002aag803 002aag805 a. SDA load configuration b. P port load configuration START SCL ACK or read cycle SDA 0.3 × VDD trst RESET 0.5 × VDD trec(rst) tw(rst) trec(rst) trst Pn 0.5 × VDD 002aah073 c. RESET timing CL includes probe and jig capacitance. All inputs are supplied by generators having the following characteristics: PRR 10 MHz; Zo = 50 ; tr/tf 30 ns. The outputs are measured one at a time, with one transition per measurement. I/Os are configured as inputs. All parameters and waveforms are not applicable to all devices. Fig 32. Reset load circuits and voltage waveforms PCAL9538A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 10 December 2012 © NXP B.V. 2012. All rights reserved. 32 of 43 PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port 15. Package outline HVQFN16: plastic thermal enhanced very thin quad flat package; no leads; 16 terminals; body 3 x 3 x 0.85 mm A B D SOT758-1 terminal 1 index area A E A1 c detail X e1 C 1/2 e e 5 y y1 C v M C A B w M C b 8 L 4 9 e e2 Eh 1/2 e 12 1 16 terminal 1 index area 13 Dh X 0 2.5 5 mm scale DIMENSIONS (mm are the original dimensions) UNIT A(1) max. A1 b c D (1) Dh E (1) Eh e e1 e2 L v w y y1 mm 1 0.05 0.00 0.30 0.18 0.2 3.1 2.9 1.75 1.45 3.1 2.9 1.75 1.45 0.5 1.5 1.5 0.5 0.3 0.1 0.05 0.05 0.1 Note 1. Plastic or metal protrusions of 0.075 mm maximum per side are not included. REFERENCES OUTLINE VERSION IEC JEDEC JEITA SOT758-1 --- MO-220 --- EUROPEAN PROJECTION ISSUE DATE 02-03-25 02-10-21 Fig 33. Package outline SOT758-1 (HVQFN16) PCAL9538A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 10 December 2012 © NXP B.V. 2012. All rights reserved. 33 of 43 PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port TSSOP16: plastic thin shrink small outline package; 16 leads; body width 4.4 mm SOT403-1 E D A X c y HE v M A Z 9 16 Q (A 3) A2 A A1 pin 1 index θ Lp L 1 8 e detail X w M bp 0 2.5 5 mm scale DIMENSIONS (mm are the original dimensions) UNIT A max. A1 A2 A3 bp c D (1) E (2) e HE L Lp Q v w y Z (1) θ mm 1.1 0.15 0.05 0.95 0.80 0.25 0.30 0.19 0.2 0.1 5.1 4.9 4.5 4.3 0.65 6.6 6.2 1 0.75 0.50 0.4 0.3 0.2 0.13 0.1 0.40 0.06 8o o 0 Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT403-1 REFERENCES IEC JEDEC JEITA MO-153 EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-18 Fig 34. Package outline SOT403-1 (TSSOP16) PCAL9538A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 10 December 2012 © NXP B.V. 2012. All rights reserved. 34 of 43 PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port 16. Handling information All input and output pins are protected against ElectroStatic Discharge (ESD) under normal handling. When handling ensure that the appropriate precautions are taken as described in JESD625-A or equivalent standards. 17. Soldering of SMD packages This text provides a very brief insight into a complex technology. A more in-depth account of soldering ICs can be found in Application Note AN10365 “Surface mount reflow soldering description”. 17.1 Introduction to soldering Soldering is one of the most common methods through which packages are attached to Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both the mechanical and the electrical connection. There is no single soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high densities that come with increased miniaturization. 17.2 Wave and reflow soldering Wave soldering is a joining technology in which the joints are made by solder coming from a standing wave of liquid solder. The wave soldering process is suitable for the following: • Through-hole components • Leaded or leadless SMDs, which are glued to the surface of the printed circuit board Not all SMDs can be wave soldered. Packages with solder balls, and some leadless packages which have solder lands underneath the body, cannot be wave soldered. Also, leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered, due to an increased probability of bridging. The reflow soldering process involves applying solder paste to a board, followed by component placement and exposure to a temperature profile. Leaded packages, packages with solder balls, and leadless packages are all reflow solderable. Key characteristics in both wave and reflow soldering are: • • • • • • Board specifications, including the board finish, solder masks and vias Package footprints, including solder thieves and orientation The moisture sensitivity level of the packages Package placement Inspection and repair Lead-free soldering versus SnPb soldering 17.3 Wave soldering Key characteristics in wave soldering are: PCAL9538A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 10 December 2012 © NXP B.V. 2012. All rights reserved. 35 of 43 PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port • Process issues, such as application of adhesive and flux, clinching of leads, board transport, the solder wave parameters, and the time during which components are exposed to the wave • Solder bath specifications, including temperature and impurities 17.4 Reflow soldering Key characteristics in reflow soldering are: • Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to higher minimum peak temperatures (see Figure 35) than a SnPb process, thus reducing the process window • Solder paste printing issues including smearing, release, and adjusting the process window for a mix of large and small components on one board • Reflow temperature profile; this profile includes preheat, reflow (in which the board is heated to the peak temperature) and cooling down. It is imperative that the peak temperature is high enough for the solder to make reliable solder joints (a solder paste characteristic). In addition, the peak temperature must be low enough that the packages and/or boards are not damaged. The peak temperature of the package depends on package thickness and volume and is classified in accordance with Table 26 and 27 Table 26. SnPb eutectic process (from J-STD-020C) Package thickness (mm) Package reflow temperature (C) Volume (mm3) < 350 350 < 2.5 235 220 2.5 220 220 Table 27. Lead-free process (from J-STD-020C) Package thickness (mm) Package reflow temperature (C) Volume (mm3) < 350 350 to 2000 > 2000 < 1.6 260 260 260 1.6 to 2.5 260 250 245 > 2.5 250 245 245 Moisture sensitivity precautions, as indicated on the packing, must be respected at all times. Studies have shown that small packages reach higher temperatures during reflow soldering, see Figure 35. PCAL9538A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 10 December 2012 © NXP B.V. 2012. All rights reserved. 36 of 43 PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port temperature maximum peak temperature = MSL limit, damage level minimum peak temperature = minimum soldering temperature peak temperature time 001aac844 MSL: Moisture Sensitivity Level Fig 35. Temperature profiles for large and small components For further information on temperature profiles, refer to Application Note AN10365 “Surface mount reflow soldering description”. PCAL9538A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 10 December 2012 © NXP B.V. 2012. All rights reserved. 37 of 43 PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port 18. Soldering: PCB footprints Footprint information for reflow soldering of HVQFN16 package SOT758-1 Hx Gx D P 0.025 0.025 C (0.105) SPx Hy SPy tot nSPx Gy SPy nSPy SLy By Ay SPx tot SLx Bx Ax solder land solder paste deposit solder land plus solder paste occupied area nSPx nSPy 2 2 Dimensions in mm P Ax Ay Bx By C D SLx SLy 0.50 4.00 4.00 2.20 2.20 0.90 0.24 1.50 1.50 Issue date SPx tot SPy tot 0.90 0.90 SPx SPy Gx Gy Hx Hy 0.30 0.30 3.30 3.30 4.25 4.25 12-03-07 12-03-08 sot758-1_fr Fig 36. PCB footprint for SOT758-1 (HVQFN16); reflow soldering PCAL9538A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 10 December 2012 © NXP B.V. 2012. All rights reserved. 38 of 43 PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port Footprint information for reflow soldering of TSSOP16 package SOT403-1 Hx Gx P2 (0.125) Hy Gy (0.125) By Ay C D2 (4x) D1 P1 Generic footprint pattern Refer to the package outline drawing for actual layout solder land occupied area DIMENSIONS in mm P1 P2 Ay By C D1 D2 Gx Gy Hx Hy 0.650 0.750 7.200 4.500 1.350 0.400 0.600 5.600 5.300 5.800 7.450 sot403-1_fr Fig 37. PCB footprint for SOT403-1 (TSSOP16); reflow soldering PCAL9538A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 10 December 2012 © NXP B.V. 2012. All rights reserved. 39 of 43 PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port 19. Abbreviations Table 28. Abbreviations Acronym Description ACPI Advanced Configuration and Power Interface CBT Cross-Bar Technology CDM Charged-Device Model CMOS Complementary Metal-Oxide Semiconductor ESD ElectroStatic Discharge FET Field-Effect Transistor FF Flip-Flop GPIO General Purpose Input/Output HBM Human Body Model I2C-bus Inter-Integrated Circuit bus I/O Input/Output LED Light Emitting Diode LP Low-Pass LSB Least Significant Bit MSB Most Significant Bit POR Power-On Reset PRR Pulse Repetition Rate SCR Silicon Controlled Rectifier SMBus System Management Bus 20. Revision history Table 29. Revision history Document ID Release date Data sheet status Change notice Supersedes PCAL9538A v.2 20121210 Product data sheet - PCAL9538A v.1 Modifications: PCAL9538A v.1 PCAL9538A Product data sheet • Section 8.5 “Device current consumption with internal pull-up and pull-down resistors”, second paragraph: first sentence corrected from “The pull-up or pull-down function is selected in registers 48h and 49h, while the resistor is connected by the enable registers 46h and 47h.” to “The pull-up or pull-down function is selected in register 44h, while the resistor is connected by the enable register 43h.” 20120928 Product data sheet - All information provided in this document is subject to legal disclaimers. Rev. 2 — 10 December 2012 - © NXP B.V. 2012. All rights reserved. 40 of 43 PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port 21. Legal information 21.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 21.2 Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification — The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet. 21.3 Disclaimers Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. NXP Semiconductors takes no responsibility for the content in this document if provided by an information source outside of NXP Semiconductors. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. PCAL9538A Product data sheet Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors and its suppliers accept no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). NXP does not accept any liability in this respect. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. All information provided in this document is subject to legal disclaimers. Rev. 2 — 10 December 2012 © NXP B.V. 2012. All rights reserved. 41 of 43 PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. Non-automotive qualified products — Unless this data sheet expressly states that this specific NXP Semiconductors product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NXP Semiconductors’ warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond NXP Semiconductors’ specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors’ standard warranty and NXP Semiconductors’ product specifications. Translations — A non-English (translated) version of a document is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions. 21.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. I2C-bus — logo is a trademark of NXP B.V. 22. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] PCAL9538A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 10 December 2012 © NXP B.V. 2012. All rights reserved. 42 of 43 PCAL9538A NXP Semiconductors Low-voltage 8-bit I2C-bus/SMBus low power I/O port 23. Contents 1 General description . . . . . . . . . . . . . . . . . . . . . . 1 2 Features and benefits . . . . . . . . . . . . . . . . . . . . 2 2.1 Agile I/O features . . . . . . . . . . . . . . . . . . . . . . . 2 3 Ordering information . . . . . . . . . . . . . . . . . . . . . 3 3.1 Ordering options . . . . . . . . . . . . . . . . . . . . . . . . 3 4 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3 5 Pinning information . . . . . . . . . . . . . . . . . . . . . . 4 5.1 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 5.2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 4 6 Functional description . . . . . . . . . . . . . . . . . . . 5 6.1 Device address . . . . . . . . . . . . . . . . . . . . . . . . . 5 6.2 Pointer register and command byte . . . . . . . . . 5 6.3 Interface definition . . . . . . . . . . . . . . . . . . . . . . 6 6.4 Register descriptions . . . . . . . . . . . . . . . . . . . . 6 6.4.1 Input port register (00h) . . . . . . . . . . . . . . . . . . 6 6.4.2 Output port register (01h) . . . . . . . . . . . . . . . . . 6 6.4.3 Polarity inversion register (02h) . . . . . . . . . . . . 7 6.4.4 Configuration register (03h) . . . . . . . . . . . . . . . 7 6.4.5 Output drive strength registers (40h, 41h) . . . . 7 6.4.6 Input latch register (42h). . . . . . . . . . . . . . . . . . 8 6.4.7 Pull-up/pull-down enable register (43h) . . . . . . 8 6.4.8 Pull-up/pull-down selection register (44h). . . . . 9 6.4.9 Interrupt mask register (45h) . . . . . . . . . . . . . . 9 6.4.10 Interrupt status register (46h) . . . . . . . . . . . . . . 9 6.4.11 Output port configuration register (47h) . . . . . 10 6.5 I/O port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 6.6 Power-on reset . . . . . . . . . . . . . . . . . . . . . . . . 11 6.7 Reset input (RESET) . . . . . . . . . . . . . . . . . . . 11 6.8 Interrupt output (INT) . . . . . . . . . . . . . . . . . . . 11 7 Bus transactions . . . . . . . . . . . . . . . . . . . . . . . 12 7.1 Write commands. . . . . . . . . . . . . . . . . . . . . . . 12 7.2 Read commands . . . . . . . . . . . . . . . . . . . . . . 13 8 Application design-in information . . . . . . . . . 15 8.1 Minimizing IDD when the I/Os are used to control LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . 15 8.2 Output drive strength control . . . . . . . . . . . . . 16 8.3 12 V tolerant I/Os . . . . . . . . . . . . . . . . . . . . . . 17 8.4 Power-on reset requirements . . . . . . . . . . . . . 18 8.5 Device current consumption with internal pull-up and pull-down resistors . . . . . . . . . . . . 20 9 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 21 10 Recommended operating conditions. . . . . . . 21 11 Thermal characteristics . . . . . . . . . . . . . . . . . 21 12 Static characteristics. . . . . . . . . . . . . . . . . . . . 22 12.1 Typical characteristics . . . . . . . . . . . . . . . . . . 24 13 14 15 16 17 17.1 17.2 17.3 17.4 18 19 20 21 21.1 21.2 21.3 21.4 22 23 Dynamic characteristics. . . . . . . . . . . . . . . . . Parameter measurement information . . . . . . Package outline. . . . . . . . . . . . . . . . . . . . . . . . Handling information . . . . . . . . . . . . . . . . . . . Soldering of SMD packages . . . . . . . . . . . . . . Introduction to soldering. . . . . . . . . . . . . . . . . Wave and reflow soldering. . . . . . . . . . . . . . . Wave soldering . . . . . . . . . . . . . . . . . . . . . . . Reflow soldering . . . . . . . . . . . . . . . . . . . . . . Soldering: PCB footprints . . . . . . . . . . . . . . . Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . Revision history . . . . . . . . . . . . . . . . . . . . . . . Legal information . . . . . . . . . . . . . . . . . . . . . . Data sheet status . . . . . . . . . . . . . . . . . . . . . . Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . Contact information . . . . . . . . . . . . . . . . . . . . Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 29 33 35 35 35 35 35 36 38 40 40 41 41 41 41 42 42 43 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. © NXP B.V. 2012. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] Date of release: 10 December 2012 Document identifier: PCAL9538A