CY2DP1502
1:2 LVPECL Fanout Buffer
1:2 LVPECL Fanout Buffer
Features
Functional Description
■
One differential (LVPECL, LVDS, HCSL, or CML) input pair
distributed to two LVPECL output pairs
■
Translates any single-ended input signal to 3.3 V LVPECL
levels with resistor bias on INx# input
■
20-ps maximum output-to-output skew
The CY2DP1502 is an ultra-low noise, low-skew,
low-propagation delay 1:2 LVPECL fanout buffer targeted to
meet the requirements of high-speed clock distribution
applications. The device has a fully differential internal
architecture that is optimized to achieve low additive jitter and
low skew at operating frequencies of up to 1.5 GHz.
■
480-ps maximum propagation delay
For a complete list of related documentation, click here.
■
0.15-ps maximum additive RMS phase jitter at 156.25 MHz
(12-kHz to 20-MHz offset)
■
Up to 1.5-GHz operation
■
8-pin SOIC or 8-pin TSSOP package
■
2.5-V or 3.3-V operating voltage [1]
■
Commercial and industrial operating temperature range
Logic Block Diagram
Note
1. Input AC-coupling capacitors are required for voltage-translation applications.
Cypress Semiconductor Corporation
Document Number: 001-56308 Rev. *M
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised May 16, 2016
CY2DP1502
Contents
Pinouts ..............................................................................3
Pin Definitions ..................................................................3
Absolute Maximum Ratings ............................................4
Operating Conditions .......................................................4
DC Electrical Specifications ............................................5
Thermal Resistance ..........................................................5
AC Electrical Specifications ............................................6
Switching Waveforms ......................................................8
Application Information .................................................10
Ordering Information ......................................................11
Ordering Code Definitions .........................................11
Document Number: 001-56308 Rev. *M
Package Diagrams ..........................................................12
Acronyms ........................................................................14
Document Conventions .................................................14
Units of Measure .......................................................14
Document History Page .................................................15
Sales, Solutions, and Legal Information ......................17
Worldwide Sales and Design Support .......................17
Products ....................................................................17
PSoC®Solutions ........................................................17
Cypress Developer Community .................................17
Technical Support ......................................................17
Page 2 of 17
CY2DP1502
Pinouts
Figure 1. 8-pin SOIC and 8-pin TSSOP pinout
Pin Definitions
Pin Number
Pin Name
Pin Type
1, 3
Q(0:1)
Output
LVPECL output clocks
2, 4
Q(0:1)#
Output
LVPECL complementary output clocks
5
VSS
Power
Ground
6
IN#
Input
Differential (LVPECL, LVDS, HCSL, or CML) complementary input clock
7
IN
Input
Differential (LVPECL, LVDS, HCSL, or CML) input clock
8
VDD
Power
Document Number: 001-56308 Rev. *M
Description
Power supply
Page 3 of 17
CY2DP1502
Absolute Maximum Ratings
Parameter
VDD
Description
Condition
Min
Max
Unit
Supply voltage
Nonfunctional
–0.5
4.6
V
VIN
Input voltage, relative to VSS
Nonfunctional
–0.5
lesser of 4.0 or
VDD + 0.4
V
VOUT[2]
DC output or I/O voltage, relative Nonfunctional
to VSS
–0.5
lesser of 4.0 or
VDD + 0.4
V
TS
Storage temperature
–55
150
°C
ESDHBM
Electrostatic discharge (ESD)
JEDEC STD 22-A114-B
protection (Human body model)
2000
–
V
LU
Latch up
UL–94
Flammability rating
MSL
Moisture sensitivity level
[2]
Nonfunctional
Meets or exceeds JEDEC Spec JESD78B
IC Latchup Test
At 1/8 in
V-0
3
Operating Conditions
Parameter
VDD
Description
Supply voltage
Min
Max
Unit
2.5-V supply
Condition
2.375
2.625
V
3.3-V supply
3.135
3.465
V
0
70
°C
TA
Ambient operating temperature
Commercial
Industrial
–40
85
°C
tPU
Power ramp time
Power-up time for VDD to reach
minimum specified voltage (power
ramp must be monotonic).
0.05
500
ms
Note
2. The voltage on any I/O pin cannot exceed the power pin during power up. Power supply sequencing is NOT required.
Document Number: 001-56308 Rev. *M
Page 4 of 17
CY2DP1502
DC Electrical Specifications
(VDD = 3.3 V ± 5% or 2.5 V ± 5%; TA = 0 °C to 70 °C (Commercial) or –40 °C to 85 °C (Industrial))
Parameter
Description
Min
Max
Unit
–
45
mA
Input high voltage, differential
inputs IN and IN#
–
VDD + 0.3
V
VIL
Input low voltage, differential
inputs IN and IN#
–0.3
–
V
VID_LVDS[3]
LVDS input differential amplitude See Figure 2 on page 8
0.4
0.8
V
VID_LVPECL[3]
LVPECL/CML/HCSL input
differential amplitude
See Figure 2 on page 8
0.4
1.0
V
IDD
Operating supply current
VIH
Condition
All LVPECL outputs floating (internal IDD)
VICM
Input common mode voltage
See Figure 2 on page 8
0.2
VDD – 0.2
V
IIH
Input high current, differential
inputs IN and IN#
Input = VDD[4]
–
150
A
IIL
Input low current, differential
inputs IN and IN#
Input = VSS[4]
–150
–
A
VOH
LVPECL output high voltage
Terminated with 50 to VDD – 2.0 [5]
VDD – 1.20 VDD – 0.70
[5]
VDD – 2.0 VDD – 1.63
VOL
LVPECL output low voltage
Terminated with 50 to VDD – 2.0
CIN
Input capacitance
Measured at 10 MHz; per pin
–
3
V
V
pF
Thermal Resistance
Parameter [6]
Description
θJA
Thermal resistance
(junction to ambient)
θJC
Thermal resistance
(junction to case)
Test Conditions
8-pin SOIC
8-pin TSSOP
Unit
Test conditions follow standard test
methods and procedures for measuring
thermal impedance, in accordance with
EIA/JESD51.
133
162
°C/W
44
29
°C/W
Notes
3. VID minimum of 400 mV is required to meet all output AC Electrical Specifications. The device is functional with VID minimum of greater than 200 mV.
4. Positive current flows into the input pin, negative current flows out of the input pin.
5. Refer to Figure 3 on page 8.
6. These parameters are guaranteed by design and are not tested.
Document Number: 001-56308 Rev. *M
Page 5 of 17
CY2DP1502
AC Electrical Specifications
(VDD = 3.3 V ± 5% or 2.5 V ± 5%; TA = 0 °C to 70 °C (Commercial) or –40 °C to 85 °C (Industrial))
Parameter
Min
Typ
Max
Unit
Differential Input
DC
–
1.5
GHz
Single-ended CMOS Input [7]
DC
–
250
MHz
FOUT = FIN,Differential Input
DC
–
1.5
GHz
FOUT = FIN,
Single-ended CMOS Input [7]
DC
–
250
MHz
LVPECL differential output
voltage peak to peak,
single-ended. terminated with
50 to VDD – 2.0 [8]
Fout = DC to 150 MHz
600
–
–
mV
Fout = >150 MHz to 1.5 GHz
400
–
–
mV
tPD[9]
Propagation delay differential
input pair to differential output
pair
Input rise/fall time < 1.5 ns
(20% to 80%)
–
–
480
ps
tODC[10]
Output duty cycle
50% duty cycle at input,
Frequency range up to 1 GHz,
Differential input
48
–
52
%
50% duty cycle at input,
Frequency range up to 250MHz,
Single-ended CMOS input [7]
45
–
55
%
FIN
FOUT
VPP
Description
Input frequency
Output frequency
Condition
tSK1[11]
Output-to-output skew
Any output to any output, with same
load conditions at DUT
–
–
20
ps
tSK1 D[11]
Device-to-device output skew
Any output to any output between
two or more devices. Devices must
have the same input and have the
same output load.
–
–
150
ps
PNADD
Additive RMS phase noise,
156.25-MHz input,
Rise/fall time < 150 ps
(20% to 80%),
VID > 400 mV or
Input Swing = 3.0 V [7]
Offset = 1 kHz
–
–
–120
dBc/
Hz
Offset = 10 kHz
–
–
–130
dBc/
Hz
Offset = 100 kHz
–
–
–135
dBc/
Hz
Offset = 1 MHz
–
–
–145
dBc/
Hz
Offset = 10 MHz
–
–
–153
dBc/
Hz
Offset = 20 MHz
–
–
–155
dBc/
Hz
Notes
7. Refer to Application Information on page 10.
8. Refer to Figure 3 on page 8.
9. Refer to Figure 4 on page 8.
10. Refer to Figure 5 on page 8.
11. Refer to Figure 6 on page 9.
Document Number: 001-56308 Rev. *M
Page 6 of 17
CY2DP1502
AC Electrical Specifications (continued)
(VDD = 3.3 V ± 5% or 2.5 V ± 5%; TA = 0 °C to 70 °C (Commercial) or –40 °C to 85 °C (Industrial))
Parameter
tJIT[12]
tR, tF[14]
Description
Additive RMS phase jitter
(Random)
Output rise/fall time
Min
Typ
Max
Unit
156.25 MHz,
12 kHz to 20 MHz offset;
input rise/fall time < 150 ps
(20% to 80%),
VID > 400 mV
Condition
–
–
0.15
ps
156.25 MHz Sinewave,
12 kHz to 20 MHz offset,
input rise/fall time < 150 ps
(20% to 80%),
Input Swing = 3.0 V [13]
–
–
0.15
ps
50% duty cycle at input,
20% to 80% of full swing
(VOL to VOH)
Input rise/fall time < 1.5 ns
(20% to 80%)
–
–
250
ps
Notes
12. Refer to Figure 7 on page 9.
13. Refer to Application Information on page 10.
14. Refer to Figure 8 on page 9.
Document Number: 001-56308 Rev. *M
Page 7 of 17
CY2DP1502
Switching Waveforms
Figure 2. Input Differential and Common Mode Voltages
Figure 3. Output Differential Voltage
Figure 4. Input to Any Output Pair Propagation Delay
Figure 5. Output Duty Cycle
Document Number: 001-56308 Rev. *M
Page 8 of 17
CY2DP1502
Switching Waveforms (continued)
Figure 6. Output-to-Output and Device-to-Device Skew
Figure 7. RMS Phase Jitter
Figure 8. Output Rise/Fall Time
Document Number: 001-56308 Rev. *M
Page 9 of 17
CY2DP1502
Application Information
CY2DP1502 can be used with a single ended CMOS input by biasing the Complementary Input Clock (INx#). “True” input pins (INx)
of differential input pair can be fed with a single ended CMOS input signal. The “complementary” input pin (INx#) of the same
differential input pair can be biased with Vref.
Figure 9 shows the schematic which can be used to give single ended CMOS input to the CY2DP1502.
The reference voltage Vref = VDD/2 is generated by the bias resistors R1, R2 and capacitor C0. This bias circuit should be located
as close as possible to the input pin. The ratio of R1 and R2 might need to be adjusted to position the Vref in the center of the input
voltage swing. For example, if the input clock swing is 2.5 V and VDD = 3.3 V, Vref should be 1.25 V and R2/R1 = 0.609.
Figure 9. Application Example
Document Number: 001-56308 Rev. *M
Page 10 of 17
CY2DP1502
Ordering Information
Part Number
Type
Production Flow
Pb-free
CY2DP1502SXI
8-pin SOIC
Industrial, –40 °C to 85 °C
CY2DP1502SXIT
8-pin SOIC – Tape and Reel
Industrial, –40 °C to 85 °C
CY2DP1502ZXI
8-pin TSSOP
Industrial, –40 °C to 85 °C
CY2DP1502ZXIT
8-pin TSSOP – Tape and Reel
Industrial, –40 °C to 85 °C
Ordering Code Definitions
CY 2DP15
02
X
X X
X
X = blank or T
blank = Tube; T = Tape and Reel
Temperature Range: X = C or I
C = Commercial; I = Industrial
Pb-free
Package Type: X = S or Z
S = 8-pin SOIC; Z = 8-pin TSSOP
Number of differential output pairs
Base part number
Company ID: CY = Cypress
Document Number: 001-56308 Rev. *M
Page 11 of 17
CY2DP1502
Package Diagrams
Figure 10. 8-pin SOIC (150 Mils) S08.15/SZ08.15 Package Outline, 51-85066
51-85066 *H
Document Number: 001-56308 Rev. *M
Page 12 of 17
CY2DP1502
Package Diagrams (continued)
Figure 11. 8-pin TSSOP 4.40 mm Body Z08.173/ZZ08.173 Package Outline, 51-85093
51-85093 *E
Document Number: 001-56308 Rev. *M
Page 13 of 17
CY2DP1502
Acronyms
Acronym
Document Conventions
Description
Units of Measure
ESD
electrostatic discharge
HBM
Human Body Model
°C
degree Celsius
HCSL
high-speed current steering logic
dBc
decibels relative to the carrier
JEDEC
Joint Electron Devices Engineering Council
GHz
gigahertz
LVDS
low-voltage differential signal
Hz
hertz
LVCMOS
low-voltage complementary metal oxide
semiconductor
k
kilohm
MHz
megahertz
μA
microampere
μF
microfarad
μs
microsecond
mA
milliampere
ms
millisecond
mV
millivolt
ns
nanosecond
ohm
LVPECL
low-voltage positive emitter-coupled logic
LVTTL
low-voltage transistor-transistor logic
RMS
root mean square
TSSOP
thin shrunk small outline package
Document Number: 001-56308 Rev. *M
Symbol
Unit of Measure
pF
picofarad
ps
picosecond
V
volt
W
watt
Page 14 of 17
CY2DP1502
Document History Page
Document Title: CY2DP1502, 1:2 LVPECL Fanout Buffer
Document Number: 001-56308
Revision
ECN
Orig. of
Change
Submission
Date
**
2782891
CXQ
10/09/09
*A
2838916
CXQ
01/05/2010
Changed status from “ADVANCE” to “PRELIMINARY”.
Changed from 0.34 ps to 0.25 ps maximum additive jitter in “Features” on page
1 and in tJIT in the AC Electrical Specs table on page 4.
Added tPU spec to the Operating Conditions table on page 2.
Change VOH in the DC Electrical Specs table on page 3: minimum from VDD 1.15V to VDD - 1.20V; maximum from VDD - 0.75V to VDD - 0.70V.
Removed VOD spec from the DC Electrical Specs table on page 3.
Added RP spec in the DC Electrical Specs table on page 3. Min = 60 k, Max
= 140 k.
Added a measurement definition for CIN in the DC Electrical Specs table on
page 3.
Added VPP spec to the AC Electrical Specs table on page 4. VPP min = 600 mV
for DC - 150 MHz and min = 400 mV for 150 MHz to 1.5 GHz.
Changed letter case and some names of all the timing parameters in the AC
Electrical Specs table on page 4 to be consistent with EROS.
Lowered all additive phase noise mask specs by 3 dB in the AC Electrical
Specs table on page 4.
Added condition to tR and tF specs in the AC Electrical specs table on page 4
that input rise/fall time must be less than 1.5 ns (20% to 80%).
Changed letter case and some names of all the timing parameters in Figures
3, 4, 5, 6 and 8, to be consistent with EROS.
*B
3011766
CXQ
08/20/2010
Changed from 0.25 ps to 0.11 ps maximum additive jitter in “Features” on page
1 and in tJIT in the AC Electrical Specs table.
Added note 3 to describe IIH and IIL specs.
Removed reference to data distribution from “Functional Description”.
Changed RP for differential inputs from 100 k to 150 k in the Logic Block
Diagram and from 60 k min / 140 k max to 90 k min / 210 k max in the
DC Electrical Specs table.
Added max VID of 1.0V in DC Electrical Specs table.
Updated phase noise specs for 1 k/10 k/100 k/1 M/10 M/20 MHz offset to
-120/-130/-135/-150/-150/-150dBc/Hz, respectively, in the AC Electrical Specs
table.
Added “Frequency range up to 1 GHz” condition to tODC spec.
Updated package diagrams.
Added Acronyms and Ordering Code Definition.
*C
3017258
CXQ
08/27/2010
Corrected Output Rise/Fall time diagram.
*D
3100234
CXQ
11/18/2010
Updated Phase jitter to 0.15ps max from 0.11ps max.
Changed VIN and VOUT specs from 4.0V to “lesser of 4.0 or VDD + 0.4”
Removed 200mA min LU spec, replaced with “Meets or exceeds JEDEC Spec
JESD78B IC Latchup Test”
Removed RP spec for differential input clock pins INX and INX#.
Changed CIN condition to “Measured at 10 MHz”.
Changed PNADD specs for 1MHz, 10MHz, and 20MHz offsets.
*E
3137726
CXQ
01/13/2011
Removed “Preliminary” status heading.
Removed resistors on IN/IN# from Logic Block Diagram.
*F
3137726
CXQ
01/13/2011
Rev’ed and posted
*G
3234654
VED
04/19/2011
Minor change, no content change.
Document Number: 001-56308 Rev. *M
Description of Change
New data sheet.
Page 15 of 17
CY2DP1502
Document History Page (continued)
Document Title: CY2DP1502, 1:2 LVPECL Fanout Buffer
Document Number: 001-56308
Revision
ECN
Orig. of
Change
Submission
Date
Description of Change
*H
3308039
CXQ
07/11/2011
Updated supported differential input clock types to include
LVPECL/LVDS/CML in Features, Pin Definitions, and DC specs table sections.
Broke out VID spec into VID_LVDS and VID_LVPECL specs.
Updated 8-pin SOIC package spec.
*I
3395868
PURU
10/05/11
Updated supported differential input clock types to include HCSL in Features,
Pinouts, and DC Electrical Specifications table.
Changed Min value of VICM.
*J
3799048
PURU
12/05/2012
Updated Features:
Added “Translates any single-ended input signal to 3.3 V LVPECL levels with
resistor bias on INx# input”.
Updated AC Electrical Specifications:
Added Note 7 and Note 13.
Added FIN parameter values for “Single Ended CMOS Input” condition
(Minimum value = DC, Maximum value = 250 MHz).
Added FOUT parameter values for “Single Ended CMOS Input” condition
(Minimum value = DC, Maximum value = 250 MHz).
Updated tPD parameter (Changed description from “Propagation delay input
pair to output pair” to “Propagation delay differential input pair to differential
output pair”).
Added tODC parameter values for “Single Ended CMOS Input” condition
(Minimum value = 45%, Maximum value = 55%).
Updated Description of PNADD parameter (Replaced “Additive RMS phase
noise, 156.25-MHz input, Rise/fall time < 150 ps (20% to 80%), VID > 400 mV”
with “Additive RMS phase noise, 156.25-MHz input, Rise/fall time < 150 ps
(20% to 80%), VID > 400 mV or Input Swing = 3.0 V[7]”).
Added tJIT parameter values for the Condition “156.25 MHz Sinewave,
12 kHz to 20 MHz offset, input rise/fall time < 150 ps (20% to 80%),
Input Swing = 3.0 V [13]” (Maximum value = 0.15 ps).
Added Application Information.
Updated Package Diagrams:
spec 51-85093 – Changed revision from *C to *D.
Updated to new template.
*K
3882598
PURU
01/24/2013
No technical updates.
Completing Sunset Review.
*L
4587249
PURU
12/04/2014
Updated Functional Description:
Added “For a complete list of related documentation, click here.” at the end.
Updated Ordering Information:
Removed the following prune part numbers CY2DP1502SXC,
CY2DP1502SXCT, CY2DP1502ZXC, and CY2DP1502ZXCT.
Updated Package Diagrams:
spec 51-85066 – Changed revision from *E to *F.
spec 51-85093 – Changed revision from *D to *E.
*M
5272915
PSR
Document Number: 001-56308 Rev. *M
05/16/2016 Added Thermal Resistance.
Updated Package Diagrams:
spec 51-85066 – Changed revision from *F to *H.
Updated to new template.
Page 16 of 17
CY2DP1502
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at Cypress Locations.
PSoC®Solutions
Products
ARM® Cortex® Microcontrollers
Automotive
cypress.com/arm
cypress.com/automotive
Clocks & Buffers
Interface
Lighting & Power Control
Memory
cypress.com/clocks
cypress.com/interface
cypress.com/powerpsoc
cypress.com/memory
PSoC
Cypress Developer Community
Forums | Projects | Video | Blogs | Training | Components
Technical Support
cypress.com/support
cypress.com/psoc
Touch Sensing
cypress.com/touch
USB Controllers
Wireless/RF
PSoC 1 | PSoC 3 | PSoC 4 | PSoC 5LP
cypress.com/usb
cypress.com/wireless
© Cypress Semiconductor Corporation, 2009-2016. This document is the property of Cypress Semiconductor Corporation and its subsidiaries, including Spansion LLC ("Cypress"). This document,
including any software or firmware included or referenced in this document ("Software"), is owned by Cypress under the intellectual property laws and treaties of the United States and other countries
worldwide. Cypress reserves all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other
intellectual property rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of the Software, then Cypress
hereby grants you a personal, non-exclusive, nontransferable license (without the right to sublicense) (1) under its copyright rights in the Software (a) for Software provided in source code form, to
modify and reproduce the Software solely for use with Cypress hardware products, only internally within your organization, and (b) to distribute the Software in binary code form externally to end users
(either directly or indirectly through resellers and distributors), solely for use on Cypress hardware product units, and (2) under those claims of Cypress's patents that are infringed by the Software (as
provided by Cypress, unmodified) to make, use, distribute, and import the Software solely for use with Cypress hardware products. Any other use, reproduction, modification, translation, or compilation
of the Software is prohibited.
TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE
OR ACCOMPANYING HARDWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. To the extent
permitted by applicable law, Cypress reserves the right to make changes to this document without further notice. Cypress does not assume any liability arising out of the application or use of any
product or circuit described in this document. Any information provided in this document, including any sample design information or programming code, is provided only for reference purposes. It is
the responsibility of the user of this document to properly design, program, and test the functionality and safety of any application made of this information and any resulting product. Cypress products
are not designed, intended, or authorized for use as critical components in systems designed or intended for the operation of weapons, weapons systems, nuclear installations, life-support devices or
systems, other medical devices or systems (including resuscitation equipment and surgical implants), pollution control or hazardous substances management, or other uses where the failure of the
device or system could cause personal injury, death, or property damage ("Unintended Uses"). A critical component is any component of a device or system whose failure to perform can be reasonably
expected to cause the failure of the device or system, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and you shall and hereby do release Cypress from any claim,
damage, or other liability arising from or related to all Unintended Uses of Cypress products. You shall indemnify and hold Cypress harmless from and against all claims, costs, damages, and other
liabilities, including claims for personal injury or death, arising from or related to any Unintended Uses of Cypress products.
Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, PSoC, CapSense, EZ-USB, F-RAM, and Traveo are trademarks or registered trademarks of Cypress in the United
States and other countries. For a more complete list of Cypress trademarks, visit cypress.com. Other names and brands may be claimed as property of their respective owners.
Document Number: 001-56308 Rev. *M
Revised May 16, 2016
Page 17 of 17