KE06 Sub-Family Reference Manual
Supports: MKE06Z64VLD4(R), MKE06Z128VLD4(R),
MKE06Z64VQH4(R), MKE06Z128VQH4(R), MKE06Z64VLH4(R),
MKE06Z128VLH4(R), MKE06Z64VLK4(R), and MKE06Z128VLK4(R)
Document Number: MKE06P80M48SF0RM
Rev 2, Feburary 2014
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
2
Freescale Semiconductor, Inc.
Contents
Section number
Title
Page
Chapter 1
About This Document
1.1
1.2
Overview.........................................................................................................................................................................37
1.1.1
Purpose.............................................................................................................................................................37
1.1.2
Audience..........................................................................................................................................................37
Conventions....................................................................................................................................................................37
1.2.1
Numbering systems..........................................................................................................................................37
1.2.2
Typographic notation.......................................................................................................................................38
1.2.3
Special terms....................................................................................................................................................38
Chapter 2
Introduction
2.1
Overview.........................................................................................................................................................................39
2.2
Module functional categories..........................................................................................................................................39
2.2.1
ARM Cortex-M0+ core modules.....................................................................................................................40
2.2.2
System modules...............................................................................................................................................41
2.2.3
Memories and memory interfaces....................................................................................................................41
2.2.4
Clocks...............................................................................................................................................................42
2.2.5
Security and integrity modules........................................................................................................................42
2.2.6
Analog modules...............................................................................................................................................42
2.2.7
Timer modules.................................................................................................................................................43
2.2.8
Communication interfaces...............................................................................................................................44
2.2.9
Human-machine interfaces..............................................................................................................................44
2.2.10
Orderable part numbers....................................................................................................................................44
Chapter 3
Chip Configuration
3.1
Introduction.....................................................................................................................................................................47
3.2
Module to Module Interconnects....................................................................................................................................47
3.2.1
Interconnection overview.................................................................................................................................47
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
3
Section number
3.3
Page
3.2.2
Analog reference options.................................................................................................................................51
3.2.3
ACMP output capture......................................................................................................................................51
3.2.4
UART0_TX modulation..................................................................................................................................52
3.2.5
UART0/1/2_RX capture..................................................................................................................................52
3.2.6
UART0_RX filter............................................................................................................................................53
3.2.7
RTC capture.....................................................................................................................................................54
3.2.8
FTM2 software synchronization......................................................................................................................54
3.2.9
ADC hardware trigger......................................................................................................................................54
Core Modules..................................................................................................................................................................55
3.3.1
3.3.2
3.3.3
ARM Cortex-M0+ core configuration.............................................................................................................55
3.3.1.1
ARM Cortex M0+ core ...............................................................................................................55
3.3.1.2
Buses, interconnects, and interfaces............................................................................................56
3.3.1.3
System Tick Timer.......................................................................................................................56
3.3.1.4
Core privilege levels....................................................................................................................57
3.3.1.5
Caches..........................................................................................................................................57
Nested Vectored Interrupt Controller (NVIC) configuration...........................................................................57
3.3.2.1
Interrupt priority levels................................................................................................................58
3.3.2.2
Non-maskable interrupt................................................................................................................58
3.3.2.3
Interrupt channel assignments......................................................................................................58
Asynchronous wakeup interrupt controller (AWIC) configuration.................................................................61
3.3.3.1
3.4
Title
Wakeup sources...........................................................................................................................61
System Modules..............................................................................................................................................................62
3.4.1
SIM configuration............................................................................................................................................62
3.4.2
PMC configuration...........................................................................................................................................63
3.4.3
MCM configuration.........................................................................................................................................63
3.4.4
Crossbar-light switch configuration.................................................................................................................64
3.4.4.1
Crossbar-Light switch master assignments..................................................................................65
3.4.4.2
Crossbar switch slave assignments..............................................................................................65
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
4
Freescale Semiconductor, Inc.
Section number
3.4.5
3.5
3.6
Peripheral bridge configuration.......................................................................................................................65
3.4.5.1
Number of peripheral bridges......................................................................................................66
3.4.5.2
Memory maps..............................................................................................................................66
3.5.1
CRC configuration...........................................................................................................................................66
3.5.2
Watchdog configuration...................................................................................................................................67
3.5.2.1
WDOG clocks..............................................................................................................................68
3.5.2.2
WDOG operation.........................................................................................................................68
Clock Modules................................................................................................................................................................69
ICS configuration.............................................................................................................................................69
3.6.1.1
3.6.2
Clock gating.................................................................................................................................69
OSC configuration...........................................................................................................................................70
Memories and Memory Interfaces..................................................................................................................................70
3.7.1
3.8
Page
System Security..............................................................................................................................................................66
3.6.1
3.7
Title
Flash memory configuration............................................................................................................................70
3.7.1.1
Flash memory sizes......................................................................................................................71
3.7.1.2
Flash memory map.......................................................................................................................71
3.7.1.3
Flash security...............................................................................................................................72
3.7.1.4
Erase all flash contents.................................................................................................................72
3.7.2
Flash memory controller configuration............................................................................................................72
3.7.3
SRAM configuration........................................................................................................................................73
3.7.3.1
SRAM sizes..................................................................................................................................74
3.7.3.2
SRAM ranges...............................................................................................................................74
3.7.3.3
SRAM bit operation.....................................................................................................................75
Analog.............................................................................................................................................................................76
3.8.1
12-bit analog-to-digital converter (ADC) configuration..................................................................................76
3.8.1.1
ADC instantiation information.....................................................................................................76
3.8.1.2
ADC0 connections/channel assignment.......................................................................................77
3.8.1.3
ADC analog supply and reference connections...........................................................................78
3.8.1.4
Temperature sensor and bandgap.................................................................................................78
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
5
Section number
3.8.1.5
3.8.2
3.9
Title
Page
Alternate clock.............................................................................................................................78
ACMP configuration........................................................................................................................................79
3.8.2.1
ACMP overview..........................................................................................................................79
3.8.2.2
ACMP interconnections...............................................................................................................80
3.8.2.3
ACMP in Stop mode....................................................................................................................81
Timers.............................................................................................................................................................................81
3.9.1
3.9.2
3.9.3
3.9.4
FlexTimer configuration..................................................................................................................................81
3.9.1.1
FTM overview..............................................................................................................................82
3.9.1.2
FTM clock options.......................................................................................................................83
3.9.1.3
FTM interconnections..................................................................................................................83
3.9.1.4
FTM interrupts.............................................................................................................................84
PIT configuration.............................................................................................................................................84
3.9.2.1
PIT overview................................................................................................................................85
3.9.2.2
PIT interconnections....................................................................................................................85
RTC configuration...........................................................................................................................................85
3.9.3.1
RTC overview..............................................................................................................................86
3.9.3.2
RTC interconnections..................................................................................................................86
PWT configuration...........................................................................................................................................87
3.9.4.1
PWT overview.............................................................................................................................87
3.9.4.2
PWT interconnections..................................................................................................................87
3.10 Communication interfaces..............................................................................................................................................88
3.10.1
SPI configuration.............................................................................................................................................88
3.10.1.1
3.10.2
3.10.3
SPI overview................................................................................................................................88
I2C configuration.............................................................................................................................................89
3.10.2.1
I2C overview................................................................................................................................89
3.10.2.2
I2C0 4-wire interface feature.......................................................................................................90
UART configuration........................................................................................................................................90
3.10.3.1
UART overview...........................................................................................................................91
3.10.3.2
UART interconnection.................................................................................................................91
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
6
Freescale Semiconductor, Inc.
Section number
3.10.4
Title
Page
MSCAN configuration.....................................................................................................................................92
3.10.4.1
MSCAN overview........................................................................................................................92
3.10.4.2
MSCAN clock source..................................................................................................................92
3.10.4.3
MSCAN wake-up interrupt and glitch filter................................................................................93
3.11 Human-machine interfaces (HMI)..................................................................................................................................93
3.11.1
GPIO configuration..........................................................................................................................................93
3.11.1.1
3.11.2
3.11.3
GPIO overview............................................................................................................................94
KBI configuration............................................................................................................................................94
3.11.2.1
KBI overview...............................................................................................................................94
3.11.2.2
KBI assignments..........................................................................................................................94
IRQ configuration............................................................................................................................................95
3.11.3.1
IRQ assignment............................................................................................................................95
Chapter 4
Memory Map
4.1
Introduction.....................................................................................................................................................................97
4.2
System memory map.......................................................................................................................................................97
4.3
Aliased bit-band region...................................................................................................................................................98
4.4
Bit Manipulation Engine.................................................................................................................................................99
4.5
System ROM memory map............................................................................................................................................99
4.6
4.7
4.5.1
Entry (ROM_ENTRYn)...................................................................................................................................101
4.5.2
End of Table Marker Register (ROM_TABLEMARK)..................................................................................102
4.5.3
System Access Register (ROM_SYSACCESS)..............................................................................................102
4.5.4
Peripheral ID Register (ROM_PERIPHIDn)...................................................................................................103
4.5.5
Component ID Register (ROM_COMPIDn)...................................................................................................103
Peripheral bridge (AIPS-Lite) memory map...................................................................................................................104
4.6.1
Read-after-write sequence and required serialization of memory operations..................................................104
4.6.2
Peripheral Bridge (AIPS-Lite) Memory Map..................................................................................................105
Private Peripheral Bus (PPB) memory map....................................................................................................................108
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
7
Section number
Title
Page
Chapter 5
Clock Distribution
5.1
Introduction.....................................................................................................................................................................111
5.2
Programming model........................................................................................................................................................111
5.3
High-level device clocking diagram...............................................................................................................................111
5.4
Clock definitions.............................................................................................................................................................113
5.4.1
Device clock summary.....................................................................................................................................113
5.4.2
Clock distribution.............................................................................................................................................114
5.5
Internal clocking sources................................................................................................................................................115
5.6
External clock sources....................................................................................................................................................116
5.7
Clock gating....................................................................................................................................................................117
5.8
Module clocks.................................................................................................................................................................117
5.8.1
FTM and PWT clocking..................................................................................................................................119
Chapter 6
Reset and Boot
6.1
Introduction.....................................................................................................................................................................121
6.2
Reset................................................................................................................................................................................121
6.2.1
Power-on reset (POR)......................................................................................................................................121
6.2.2
System reset sources........................................................................................................................................122
6.2.3
6.2.2.1
External pin reset (RESET)..........................................................................................................122
6.2.2.2
Low-voltage detect (LVD)...........................................................................................................123
6.2.2.3
Watchdog timer............................................................................................................................123
6.2.2.4
ICS loss-of-clock (LOC)..............................................................................................................123
6.2.2.5
Stop mode acknowledge error (SACKERR) ..............................................................................124
6.2.2.6
Software reset (SW).....................................................................................................................124
6.2.2.7
Lockup reset (LOCKUP).............................................................................................................124
6.2.2.8
MDM-AP system reset request....................................................................................................124
MCU resets......................................................................................................................................................124
6.2.3.1
POR Only ....................................................................................................................................124
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
8
Freescale Semiconductor, Inc.
Section number
6.3
Title
Page
6.2.3.2
Chip POR ....................................................................................................................................125
6.2.3.3
Early Chip Reset .........................................................................................................................125
6.2.3.4
Chip Reset ...................................................................................................................................125
Boot.................................................................................................................................................................................125
6.3.1
Boot sources.....................................................................................................................................................125
6.3.2
Boot sequence..................................................................................................................................................126
Chapter 7
Power Management
7.1
Introduction.....................................................................................................................................................................127
7.2
Power modes...................................................................................................................................................................127
7.3
Entering and exiting power modes.................................................................................................................................128
7.4
Module operation in low-power modes..........................................................................................................................128
Chapter 8
Security
8.1
Introduction.....................................................................................................................................................................131
8.2
Flash security..................................................................................................................................................................131
8.3
Security interactions with other modules........................................................................................................................132
8.3.1
Security interactions with debug......................................................................................................................132
Chapter 9
Debug
9.1
Introduction.....................................................................................................................................................................133
9.2
Debug port pin descriptions............................................................................................................................................133
9.3
SWD status and control registers....................................................................................................................................134
9.3.1
MDM-AP status register..................................................................................................................................135
9.3.2
MDM-AP Control register...............................................................................................................................136
9.4
Debug resets....................................................................................................................................................................137
9.5
Debug in low-power modes............................................................................................................................................137
9.6
Debug and security.........................................................................................................................................................138
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
9
Section number
Title
Page
Chapter 10
Signal Multiplexing and Signal Descriptions
10.1 Introduction.....................................................................................................................................................................139
10.2 Pinout..............................................................................................................................................................................139
10.2.1
Signal multiplexing and pin assignments.........................................................................................................139
10.2.2
Device pin assignment.....................................................................................................................................142
10.3 Module signal description tables....................................................................................................................................144
10.3.1
Core modules...................................................................................................................................................144
10.3.2
System modules...............................................................................................................................................145
10.3.3
Clock modules..................................................................................................................................................145
10.3.4
Analog..............................................................................................................................................................145
10.3.5
Timer modules.................................................................................................................................................146
10.3.6
Communication Interfaces...............................................................................................................................147
10.3.7
Human-machine interfaces (HMI)...................................................................................................................149
Chapter 11
Port Control (PORT)
11.1 Introduction.....................................................................................................................................................................151
11.2 Port data and data direction.............................................................................................................................................153
11.3 Internal pullup enable.....................................................................................................................................................154
11.4 Input glitch filter setting..................................................................................................................................................154
11.5 High current drive...........................................................................................................................................................155
11.6 Pin behavior in Stop mode..............................................................................................................................................155
11.7 Port data registers............................................................................................................................................................156
11.7.1
Port Filter Register 0 (PORT_IOFLT0)...........................................................................................................156
11.7.2
Port Filter Register 1 (PORT_IOFLT1)...........................................................................................................159
11.7.3
Port Pullup Enable Register 0 (PORT_PUE0).................................................................................................160
11.7.4
Port Pullup Enable Register 1 (PORT_PUE1).................................................................................................165
11.7.5
Port Pullup Enable Register 2 (PORT_PUE2).................................................................................................170
11.7.6
Port High Drive Enable Register (PORT_HDRVE)........................................................................................172
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
10
Freescale Semiconductor, Inc.
Section number
Title
Page
Chapter 12
System Integration Module (SIM)
12.1 Introduction.....................................................................................................................................................................175
12.1.1
Features............................................................................................................................................................175
12.2 Memory map and register definition...............................................................................................................................175
12.2.1
System Reset Status and ID Register (SIM_SRSID).......................................................................................176
12.2.2
System Options Register 0 (SIM_SOPT0)......................................................................................................179
12.2.3
System Options Register (SIM_SOPT1).........................................................................................................182
12.2.4
Pin Selection Register 0 (SIM_PINSEL0).......................................................................................................184
12.2.5
Pin Selection Register 1 (SIM_PINSEL1).......................................................................................................186
12.2.6
System Clock Gating Control Register (SIM_SCGC).....................................................................................188
12.2.7
Universally Unique Identifier Low Register (SIM_UUIDL)..........................................................................192
12.2.8
Universally Unique Identifier Middle Low Register (SIM_UUIDML)..........................................................192
12.2.9
Universally Unique Identifier Middle High Register (SIM_UUIDMH).........................................................193
12.2.10 Clock Divider Register (SIM_CLKDIV).........................................................................................................193
12.3 Functional description.....................................................................................................................................................194
Chapter 13
Power Management Controller (PMC)
13.1 Introduction.....................................................................................................................................................................195
13.2 Low voltage detect (LVD) system..................................................................................................................................195
13.2.1
Power-on reset (POR) operation......................................................................................................................196
13.2.2
LVD reset operation.........................................................................................................................................196
13.2.3
LVD enabled in Stop mode..............................................................................................................................196
13.2.4
Low-voltage warning (LVW)..........................................................................................................................197
13.3 Bandgap reference..........................................................................................................................................................197
13.4 Memory map and register descriptions...........................................................................................................................197
13.4.1
System Power Management Status and Control 1 Register (PMC_SPMSC1)................................................198
13.4.2
System Power Management Status and Control 2 Register (PMC_SPMSC2)................................................199
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
11
Section number
Title
Page
Chapter 14
Miscellaneous Control Module (MCM)
14.1 Introduction.....................................................................................................................................................................201
14.1.1
Features............................................................................................................................................................201
14.2 Memory map/register descriptions.................................................................................................................................201
14.2.1
Crossbar Switch (AXBS) Slave Configuration (MCM_PLASC)....................................................................202
14.2.2
Crossbar Switch (AXBS) Master Configuration (MCM_PLAMC)................................................................202
14.2.3
Platform Control Register (MCM_PLACR)....................................................................................................203
Chapter 15
Peripheral Bridge (AIPS-Lite)
15.1 Introduction.....................................................................................................................................................................207
15.1.1
Features............................................................................................................................................................207
15.1.2
General operation.............................................................................................................................................207
15.2 Functional description.....................................................................................................................................................208
15.2.1
Access support.................................................................................................................................................208
Chapter 16
Watchdog Timer (WDOG)
16.1 Introduction.....................................................................................................................................................................209
16.1.1
Features............................................................................................................................................................209
16.1.2
Block diagram..................................................................................................................................................210
16.2 Memory map and register definition...............................................................................................................................211
16.2.1
Watchdog Control and Status Register 1 (WDOG_CS1)................................................................................211
16.2.2
Watchdog Control and Status Register 2 (WDOG_CS2)................................................................................213
16.2.3
Watchdog Counter Register: High (WDOG_CNTH)......................................................................................214
16.2.4
Watchdog Counter Register: Low (WDOG_CNTL).......................................................................................214
16.2.5
Watchdog Timeout Value Register: High (WDOG_TOVALH).....................................................................215
16.2.6
Watchdog Timeout Value Register: Low (WDOG_TOVALL)......................................................................215
16.2.7
Watchdog Window Register: High (WDOG_WINH).....................................................................................216
16.2.8
Watchdog Window Register: Low (WDOG_WINL)......................................................................................216
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
12
Freescale Semiconductor, Inc.
Section number
Title
Page
16.3 Functional description.....................................................................................................................................................217
16.3.1
16.3.2
Watchdog refresh mechanism..........................................................................................................................217
16.3.1.1
Window mode..............................................................................................................................218
16.3.1.2
Refreshing the Watchdog.............................................................................................................218
16.3.1.3
Example code: Refreshing the Watchdog....................................................................................219
Configuring the Watchdog...............................................................................................................................219
16.3.2.1
Reconfiguring the Watchdog.......................................................................................................220
16.3.2.2
Unlocking the Watchdog.............................................................................................................220
16.3.2.3
Example code: Reconfiguring the Watchdog..............................................................................220
16.3.3
Clock source.....................................................................................................................................................221
16.3.4
Using interrupts to delay resets........................................................................................................................222
16.3.5
Backup reset.....................................................................................................................................................222
16.3.6
Functionality in debug and low-power modes.................................................................................................222
16.3.7
Fast testing of the watchdog.............................................................................................................................223
16.3.7.1
Testing each byte of the counter..................................................................................................223
16.3.7.2
Entering user mode......................................................................................................................224
Chapter 17
Bit Manipulation Engine (BME)
17.1 Introduction.....................................................................................................................................................................225
17.1.1
Overview..........................................................................................................................................................226
17.1.2
Features............................................................................................................................................................227
17.1.3
Modes of operation..........................................................................................................................................227
17.2 Memory map and register definition...............................................................................................................................227
17.3 Functional description.....................................................................................................................................................228
17.3.1
BME decorated stores......................................................................................................................................228
17.3.1.1
Decorated store logical AND (AND)...........................................................................................230
17.3.1.2
Decorated store logical OR (OR).................................................................................................231
17.3.1.3
Decorated store logical XOR (XOR)...........................................................................................232
17.3.1.4
Decorated store bit field insert (BFI)...........................................................................................233
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
13
Section number
17.3.2
17.3.3
Title
Page
BME decorated loads.......................................................................................................................................235
17.3.2.1
Decorated load: load-and-clear 1 bit (LAC1)..............................................................................238
17.3.2.2
Decorated Load: Load-and-Set 1 Bit (LAS1)..............................................................................239
17.3.2.3
Decorated load unsigned bit field extract (UBFX)......................................................................240
Additional details on decorated addresses and GPIO accesses........................................................................241
17.4 Application information..................................................................................................................................................242
Chapter 18
Flash Memory Module (FTMRE)
18.1 Introduction.....................................................................................................................................................................245
18.2 Feature.............................................................................................................................................................................245
18.2.1
Flash memory features.....................................................................................................................................245
18.2.2
Other flash module features.............................................................................................................................246
18.3 Functional description.....................................................................................................................................................246
18.3.1
Modes of operation..........................................................................................................................................246
18.3.1.1
Wait mode....................................................................................................................................246
18.3.1.2
Stop mode....................................................................................................................................246
18.3.2
Flash memory map...........................................................................................................................................246
18.3.3
Flash initialization after system reset...............................................................................................................247
18.3.4
Flash command operations...............................................................................................................................247
18.3.5
18.3.4.1
Writing the FCLKDIV register....................................................................................................249
18.3.4.2
Command write sequence............................................................................................................251
Flash interrupts.................................................................................................................................................253
18.3.5.1
Description of flash interrupt operation.......................................................................................253
18.3.6
Protection.........................................................................................................................................................253
18.3.7
Security............................................................................................................................................................258
18.3.7.1
Unsecuring the MCU using backdoor key access........................................................................258
18.3.7.2
Unsecuring the MCU using SWD................................................................................................259
18.3.7.3
Mode and security effects on flash command availability...........................................................259
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
14
Freescale Semiconductor, Inc.
Section number
18.3.8
Page
Flash commands...............................................................................................................................................259
18.3.8.1
18.3.9
Title
Flash commands...........................................................................................................................260
Flash command summary................................................................................................................................260
18.3.9.1
Erase Verify All Blocks command..............................................................................................261
18.3.9.2
Erase Verify Block command......................................................................................................262
18.3.9.3
Erase Verify Flash Section command..........................................................................................262
18.3.9.4
Read once command....................................................................................................................263
18.3.9.5
Program Flash command.............................................................................................................264
18.3.9.6
Program Once command..............................................................................................................265
18.3.9.7
Erase All Blocks command..........................................................................................................266
18.3.9.8
Debugger mass erase request.......................................................................................................267
18.3.9.9
Erase flash block command.........................................................................................................268
18.3.9.10
Erase flash sector command.........................................................................................................268
18.3.9.11
Unsecure flash command.............................................................................................................269
18.3.9.12
Verify backdoor access key command.........................................................................................270
18.3.9.13
Set user margin level command...................................................................................................271
18.3.9.14
Set factory margin level command..............................................................................................272
18.3.9.15
Configure NVM command..........................................................................................................273
18.4 Memory map and register definition...............................................................................................................................276
18.4.1
Flash CCOB Index Register (FTMRE_FCCOBIX)........................................................................................276
18.4.2
Flash Security Register (FTMRE_FSEC)........................................................................................................277
18.4.3
Flash Clock Divider Register (FTMRE_FCLKDIV).......................................................................................278
18.4.4
Flash Status Register (FTMRE_FSTAT).........................................................................................................279
18.4.5
Flash Configuration Register (FTMRE_FCNFG)...........................................................................................280
18.4.6
Flash Common Command Object Register: Low (FTMRE_FCCOBLO).......................................................281
18.4.7
Flash Common Command Object Register:High (FTMRE_FCCOBHI)........................................................281
18.4.8
Flash Protection Register (FTMRE_FPROT)..................................................................................................281
18.4.9
Flash Option Register (FTMRE_FOPT)..........................................................................................................283
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
15
Section number
Title
Page
Chapter 19
Flash Memory Controller (FMC)
19.1 Introduction.....................................................................................................................................................................285
19.1.1
Overview..........................................................................................................................................................285
19.1.2
Features............................................................................................................................................................285
19.2 Modes of operation.........................................................................................................................................................286
19.3 External signal description..............................................................................................................................................286
19.4 Memory map and register descriptions...........................................................................................................................286
19.5 Functional description.....................................................................................................................................................286
Chapter 20
Internal Clock Source (ICS)
20.1 Introduction.....................................................................................................................................................................289
20.1.1
Features............................................................................................................................................................289
20.1.2
Block diagram..................................................................................................................................................290
20.1.3
Modes of operation..........................................................................................................................................290
20.1.3.1
FLL engaged internal (FEI).........................................................................................................290
20.1.3.2
FLL engaged external (FEE)........................................................................................................290
20.1.3.3
FLL bypassed internal (FBI)........................................................................................................291
20.1.3.4
FLL bypassed internal low power (FBILP).................................................................................291
20.1.3.5
FLL bypassed external (FBE)......................................................................................................291
20.1.3.6
FLL bypassed external low power (FBELP)...............................................................................291
20.1.3.7
Stop (STOP).................................................................................................................................291
20.2 External signal description..............................................................................................................................................292
20.3 Register definition...........................................................................................................................................................292
20.3.1
ICS Control Register 1 (ICS_C1)....................................................................................................................292
20.3.2
ICS Control Register 2 (ICS_C2)....................................................................................................................293
20.3.3
ICS Control Register 3 (ICS_C3)....................................................................................................................294
20.3.4
ICS Control Register 4 (ICS_C4)....................................................................................................................295
20.3.5
ICS Status Register (ICS_S)............................................................................................................................295
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
16
Freescale Semiconductor, Inc.
Section number
Title
Page
20.4 Functional description.....................................................................................................................................................296
20.4.1
Operational modes...........................................................................................................................................296
20.4.1.1
FLL engaged internal (FEI).........................................................................................................297
20.4.1.2
FLL engaged external (FEE)........................................................................................................297
20.4.1.3
FLL bypassed internal (FBI)........................................................................................................298
20.4.1.4
FLL bypassed internal low power (FBILP).................................................................................298
20.4.1.5
FLL bypassed external (FBE)......................................................................................................298
20.4.1.6
FLL bypassed external low power (FBELP)...............................................................................299
20.4.1.7
Stop..............................................................................................................................................299
20.4.2
Mode switching................................................................................................................................................299
20.4.3
Bus frequency divider......................................................................................................................................300
20.4.4
Low-power field usage.....................................................................................................................................300
20.4.5
Internal reference clock....................................................................................................................................300
20.4.6
Fixed frequency clock......................................................................................................................................300
20.4.7
FLL lock and clock monitor.............................................................................................................................301
20.4.7.1
FLL clock lock.............................................................................................................................301
20.4.7.2
External reference clock monitor.................................................................................................301
20.5 Initialization/application information.............................................................................................................................302
20.5.1
Initializing FEI mode.......................................................................................................................................302
20.5.2
Initializing FBI mode.......................................................................................................................................302
20.5.3
Initializing FEE mode......................................................................................................................................302
20.5.4
Initializing FBE mode......................................................................................................................................303
Chapter 21
Oscillator (OSC)
21.1 Introduction.....................................................................................................................................................................305
21.1.1
Overview..........................................................................................................................................................305
21.1.2
Features and modes..........................................................................................................................................305
21.1.3
Block diagram..................................................................................................................................................305
21.2 Signal description............................................................................................................................................................306
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
17
Section number
Title
Page
21.3 External crystal / resonator connections.........................................................................................................................307
21.4 External clock connections.............................................................................................................................................308
21.5 Memory map and register descriptions...........................................................................................................................309
21.5.1
OSC Control Register (OSC_CR)....................................................................................................................309
21.6 Functional description.....................................................................................................................................................310
21.6.1
21.6.2
OSC module states...........................................................................................................................................310
21.6.1.1
Off................................................................................................................................................311
21.6.1.2
Oscillator startup..........................................................................................................................312
21.6.1.3
Oscillator stable............................................................................................................................312
21.6.1.4
External clock mode.....................................................................................................................312
OSC module modes.........................................................................................................................................312
21.6.2.1
Low-frequency, high-gain mode..................................................................................................313
21.6.2.2
Low-frequency, low-power mode................................................................................................313
21.6.2.3
High-frequency, high-gain mode.................................................................................................313
21.6.2.4
High-frequency, low-power mode...............................................................................................314
21.6.3
Counter.............................................................................................................................................................314
21.6.4
Reference clock pin requirements....................................................................................................................314
Chapter 22
Cyclic Redundancy Check (CRC)
22.1 Introduction.....................................................................................................................................................................315
22.1.1
Features............................................................................................................................................................315
22.1.2
Block diagram..................................................................................................................................................315
22.1.3
Modes of operation..........................................................................................................................................316
22.1.3.1
Run mode.....................................................................................................................................316
22.1.3.2
Low-power modes (Wait or Stop)...............................................................................................316
22.2 Memory map and register descriptions...........................................................................................................................316
22.2.1
CRC Data register (CRC_DATA)...................................................................................................................317
22.2.2
CRC Polynomial register (CRC_GPOLY)......................................................................................................318
22.2.3
CRC Control register (CRC_CTRL)................................................................................................................318
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
18
Freescale Semiconductor, Inc.
Section number
Title
Page
22.3 Functional description.....................................................................................................................................................319
22.3.1
CRC initialization/reinitialization....................................................................................................................319
22.3.2
CRC calculations..............................................................................................................................................320
22.3.3
22.3.2.1
16-bit CRC...................................................................................................................................320
22.3.2.2
32-bit CRC...................................................................................................................................320
Transpose feature.............................................................................................................................................321
22.3.3.1
22.3.4
Types of transpose.......................................................................................................................321
CRC result complement...................................................................................................................................323
Chapter 23
Interrupt (IRQ)
23.1 Introduction.....................................................................................................................................................................325
23.2 Features...........................................................................................................................................................................325
23.2.1
Pin configuration options.................................................................................................................................326
23.2.2
Edge and level sensitivity................................................................................................................................327
23.3 Interrupt pin request register...........................................................................................................................................327
23.3.1
Interrupt Pin Request Status and Control Register (IRQ_SC).........................................................................327
Chapter 24
Analog-to-digital converter (ADC)
24.1 Introduction.....................................................................................................................................................................329
24.1.1
Features............................................................................................................................................................329
24.1.2
Block Diagram.................................................................................................................................................330
24.2 External Signal Description............................................................................................................................................330
24.2.1
Analog Power (VDDA)...................................................................................................................................331
24.2.2
Analog Ground (VSSA)...................................................................................................................................331
24.2.3
Voltage Reference High (VREFH)..................................................................................................................331
24.2.4
Voltage Reference Low (VREFL)...................................................................................................................331
24.2.5
Analog Channel Inputs (ADx).........................................................................................................................331
24.3 ADC Control Registers...................................................................................................................................................332
24.3.1
Status and Control Register 1 (ADC_SC1)......................................................................................................332
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
19
Section number
Title
Page
24.3.2
Status and Control Register 2 (ADC_SC2)......................................................................................................335
24.3.3
Status and Control Register 3 (ADC_SC3)......................................................................................................337
24.3.4
Status and Control Register 4 (ADC_SC4)......................................................................................................338
24.3.5
Conversion Result Register (ADC_R).............................................................................................................339
24.3.6
Compare Value Register (ADC_CV)..............................................................................................................340
24.3.7
Pin Control 1 Register (ADC_APCTL1).........................................................................................................341
24.3.8
Status and Control Register 5 (ADC_SC5)......................................................................................................341
24.4 Functional description.....................................................................................................................................................342
24.4.1
Clock select and divide control........................................................................................................................342
24.4.2
Input select and pin control..............................................................................................................................343
24.4.3
Hardware trigger..............................................................................................................................................343
24.4.4
Conversion control...........................................................................................................................................344
24.4.4.1
Initiating conversions...................................................................................................................344
24.4.4.2
Completing conversions...............................................................................................................344
24.4.4.3
Aborting conversions...................................................................................................................345
24.4.4.4
Power control...............................................................................................................................345
24.4.4.5
Sample time and total conversion time........................................................................................345
24.4.5
Automatic compare function............................................................................................................................347
24.4.6
FIFO operation.................................................................................................................................................348
24.4.7
MCU wait mode operation...............................................................................................................................352
24.4.8
MCU Stop mode operation..............................................................................................................................352
24.4.8.1
Stop mode with ADACK disabled...............................................................................................352
24.4.8.2
Stop mode with ADACK enabled................................................................................................352
24.5 Initialization information................................................................................................................................................353
24.5.1
ADC module initialization example................................................................................................................353
24.5.1.1
Initialization sequence..................................................................................................................353
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
20
Freescale Semiconductor, Inc.
Section number
24.5.1.2
24.5.2
Title
Page
Pseudo-code example...................................................................................................................354
ADC FIFO module initialization example.......................................................................................................354
24.5.2.1
Pseudo-code example...................................................................................................................355
24.6 Application information..................................................................................................................................................356
24.6.1
24.6.2
External pins and routing.................................................................................................................................356
24.6.1.1
Analog supply pins.......................................................................................................................356
24.6.1.2
Analog reference pins..................................................................................................................356
24.6.1.3
Analog input pins.........................................................................................................................357
Sources of error................................................................................................................................................358
24.6.2.1
Sampling error..............................................................................................................................358
24.6.2.2
Pin leakage error..........................................................................................................................358
24.6.2.3
Noise-induced errors....................................................................................................................358
24.6.2.4
Code width and quantization error...............................................................................................359
24.6.2.5
Linearity errors.............................................................................................................................360
24.6.2.6
Code jitter, non-monotonicity, and missing codes.......................................................................360
Chapter 25
Analog comparator (ACMP)
25.1 Introduction.....................................................................................................................................................................363
25.1.1
Features............................................................................................................................................................363
25.1.2
Modes of operation..........................................................................................................................................363
25.1.3
25.1.2.1
Operation in Wait mode...............................................................................................................364
25.1.2.2
Operation in Stop mode...............................................................................................................364
25.1.2.3
Operation in Debug mode............................................................................................................364
Block diagram..................................................................................................................................................364
25.2 External signal description..............................................................................................................................................365
25.3 Memory map and register definition...............................................................................................................................365
25.3.1
ACMP Control and Status Register (ACMPx_CS)..........................................................................................366
25.3.2
ACMP Control Register 0 (ACMPx_C0)........................................................................................................367
25.3.3
ACMP Control Register 1 (ACMPx_C1)........................................................................................................367
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
21
Section number
25.3.4
Title
Page
ACMP Control Register 2 (ACMPx_C2)........................................................................................................368
25.4 Functional description.....................................................................................................................................................368
25.5 Setup and operation of ACMP........................................................................................................................................369
25.6 Resets..............................................................................................................................................................................370
25.7 Interrupts.........................................................................................................................................................................370
Chapter 26
FlexTimer Module (FTM)
26.1 Introduction.....................................................................................................................................................................371
26.1.1
FlexTimer philosophy......................................................................................................................................371
26.1.2
Features............................................................................................................................................................372
26.1.3
Modes of operation..........................................................................................................................................373
26.1.4
Block diagram..................................................................................................................................................374
26.2 FTM signal descriptions.................................................................................................................................................376
26.3 Memory map and register definition...............................................................................................................................376
26.3.1
Memory map....................................................................................................................................................376
26.3.2
Register descriptions........................................................................................................................................376
26.3.3
Status And Control (FTMx_SC)......................................................................................................................380
26.3.4
Counter (FTMx_CNT).....................................................................................................................................382
26.3.5
Modulo (FTMx_MOD)....................................................................................................................................382
26.3.6
Channel (n) Status And Control (FTMx_CnSC)..............................................................................................383
26.3.7
Channel (n) Value (FTMx_CnV).....................................................................................................................385
26.3.8
Counter Initial Value (FTMx_CNTIN)............................................................................................................386
26.3.9
Capture And Compare Status (FTMx_STATUS)............................................................................................387
26.3.10 Features Mode Selection (FTMx_MODE)......................................................................................................389
26.3.11 Synchronization (FTMx_SYNC).....................................................................................................................390
26.3.12 Initial State For Channels Output (FTMx_OUTINIT).....................................................................................393
26.3.13 Output Mask (FTMx_OUTMASK).................................................................................................................394
26.3.14 Function For Linked Channels (FTMx_COMBINE).......................................................................................396
26.3.15 Deadtime Insertion Control (FTMx_DEADTIME).........................................................................................401
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
22
Freescale Semiconductor, Inc.
Section number
Title
Page
26.3.16 FTM External Trigger (FTMx_EXTTRIG).....................................................................................................402
26.3.17 Channels Polarity (FTMx_POL)......................................................................................................................404
26.3.18 Fault Mode Status (FTMx_FMS).....................................................................................................................406
26.3.19 Input Capture Filter Control (FTMx_FILTER)...............................................................................................408
26.3.20 Fault Control (FTMx_FLTCTRL)...................................................................................................................409
26.3.21 Configuration (FTMx_CONF).........................................................................................................................411
26.3.22 FTM Fault Input Polarity (FTMx_FLTPOL)...................................................................................................412
26.3.23 Synchronization Configuration (FTMx_SYNCONF)......................................................................................414
26.3.24 FTM Inverting Control (FTMx_INVCTRL)....................................................................................................416
26.3.25 FTM Software Output Control (FTMx_SWOCTRL)......................................................................................417
26.3.26 FTM PWM Load (FTMx_PWMLOAD).........................................................................................................419
26.4 Functional description.....................................................................................................................................................420
26.4.1
Clock source.....................................................................................................................................................421
26.4.1.1
Counter clock source....................................................................................................................421
26.4.2
Prescaler...........................................................................................................................................................422
26.4.3
Counter.............................................................................................................................................................422
26.4.4
26.4.3.1
Up counting..................................................................................................................................422
26.4.3.2
Up-down counting........................................................................................................................425
26.4.3.3
Free running counter....................................................................................................................426
26.4.3.4
Counter reset................................................................................................................................427
26.4.3.5
When the TOF bit is set...............................................................................................................427
Input Capture mode..........................................................................................................................................427
26.4.4.1
Filter for Input Capture mode......................................................................................................429
26.4.5
Output Compare mode.....................................................................................................................................430
26.4.6
Edge-Aligned PWM (EPWM) mode...............................................................................................................431
26.4.7
Center-Aligned PWM (CPWM) mode............................................................................................................433
26.4.8
Combine mode.................................................................................................................................................435
26.4.8.1
26.4.9
Asymmetrical PWM....................................................................................................................442
Complementary mode......................................................................................................................................442
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
23
Section number
Title
Page
26.4.10 Registers updated from write buffers...............................................................................................................443
26.4.10.1
CNTIN register update.................................................................................................................443
26.4.10.2
MOD register update....................................................................................................................444
26.4.10.3
CnV register update.....................................................................................................................444
26.4.11 PWM synchronization......................................................................................................................................445
26.4.11.1
Hardware trigger..........................................................................................................................445
26.4.11.2
Software trigger............................................................................................................................446
26.4.11.3
Boundary cycle and loading points..............................................................................................447
26.4.11.4
MOD register synchronization.....................................................................................................448
26.4.11.5
CNTIN register synchronization..................................................................................................451
26.4.11.6
C(n)V and C(n+1)V register synchronization..............................................................................452
26.4.11.7
OUTMASK register synchronization..........................................................................................452
26.4.11.8
INVCTRL register synchronization.............................................................................................455
26.4.11.9
SWOCTRL register synchronization...........................................................................................456
26.4.11.10 FTM counter synchronization......................................................................................................458
26.4.12 Inverting...........................................................................................................................................................461
26.4.13 Software output control....................................................................................................................................463
26.4.14 Deadtime insertion...........................................................................................................................................465
26.4.14.1
Deadtime insertion corner cases..................................................................................................466
26.4.15 Output mask.....................................................................................................................................................468
26.4.16 Fault control.....................................................................................................................................................469
26.4.16.1
Automatic fault clearing...............................................................................................................471
26.4.16.2
Manual fault clearing...................................................................................................................471
26.4.16.3
Fault inputs polarity control.........................................................................................................472
26.4.17 Polarity control.................................................................................................................................................472
26.4.18 Initialization.....................................................................................................................................................473
26.4.19 Features priority...............................................................................................................................................473
26.4.20 Channel trigger output.....................................................................................................................................474
26.4.21 Initialization trigger..........................................................................................................................................475
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
24
Freescale Semiconductor, Inc.
Section number
Title
Page
26.4.22 Capture Test mode...........................................................................................................................................477
26.4.23 Dual Edge Capture mode.................................................................................................................................478
26.4.23.1
One-Shot Capture mode...............................................................................................................479
26.4.23.2
Continuous Capture mode............................................................................................................480
26.4.23.3
Pulse width measurement.............................................................................................................480
26.4.23.4
Period measurement.....................................................................................................................482
26.4.23.5
Read coherency mechanism.........................................................................................................484
26.4.24 Debug mode.....................................................................................................................................................485
26.4.25 Intermediate load..............................................................................................................................................486
26.4.26 Global time base (GTB)...................................................................................................................................488
26.4.26.1
Enabling the global time base (GTB)..........................................................................................489
26.5 Reset overview................................................................................................................................................................490
26.6 FTM Interrupts................................................................................................................................................................491
26.6.1
Timer Overflow Interrupt.................................................................................................................................492
26.6.2
Channel (n) Interrupt........................................................................................................................................492
26.6.3
Fault Interrupt..................................................................................................................................................492
Chapter 27
Pulse Width Timer (PWT)
27.1 Introduction.....................................................................................................................................................................493
27.1.1
Features............................................................................................................................................................493
27.1.2
Modes of operation..........................................................................................................................................493
27.1.3
Block diagram..................................................................................................................................................494
27.2 PWT signal description...................................................................................................................................................495
27.2.1
PWTIN[3:0] - Pulse Width Timer Capture Inputs...........................................................................................495
27.2.2
ALTCLK- Alternative Clock Source for Counter...........................................................................................495
27.3 Memory Map and Register Descriptions........................................................................................................................495
27.3.1
Pulse Width Timer Register 1 (PWT_R1).......................................................................................................496
27.3.2
Pulse Width Timer Register 2 (PWT_R2).......................................................................................................498
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
25
Section number
Title
Page
27.4 Functional Description....................................................................................................................................................499
27.4.1
PWT Counter and PWT Clock Prescaler.........................................................................................................499
27.4.2
Edge detection and capture control .................................................................................................................499
27.5 Reset................................................................................................................................................................................503
27.5.1
General.............................................................................................................................................................503
27.5.2
Description of reset operation..........................................................................................................................503
27.6 Interrupts.........................................................................................................................................................................503
27.6.1
Description of interrupt operation....................................................................................................................503
27.6.2
Application examples.......................................................................................................................................504
Chapter 28
Periodic Interrupt Timer (PIT)
28.1 Introduction.....................................................................................................................................................................507
28.1.1
Block diagram..................................................................................................................................................507
28.1.2
Features............................................................................................................................................................508
28.2 Signal description............................................................................................................................................................508
28.3 Memory map/register description...................................................................................................................................509
28.3.1
PIT Module Control Register (PIT_MCR)......................................................................................................509
28.3.2
Timer Load Value Register (PIT_LDVALn)...................................................................................................510
28.3.3
Current Timer Value Register (PIT_CVALn).................................................................................................511
28.3.4
Timer Control Register (PIT_TCTRLn)..........................................................................................................511
28.3.5
Timer Flag Register (PIT_TFLGn)..................................................................................................................512
28.4 Functional description.....................................................................................................................................................513
28.4.1
General operation.............................................................................................................................................513
28.4.1.1
Timers..........................................................................................................................................513
28.4.1.2
Debug mode.................................................................................................................................514
28.4.2
Interrupts..........................................................................................................................................................514
28.4.3
Chained timers.................................................................................................................................................515
28.5 Initialization and application information.......................................................................................................................515
28.6 Example configuration for chained timers......................................................................................................................516
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
26
Freescale Semiconductor, Inc.
Section number
Title
Page
Chapter 29
Real-Time Counter (RTC)
29.1 Introduction.....................................................................................................................................................................519
29.2 Features...........................................................................................................................................................................519
29.2.1
29.2.2
Modes of operation..........................................................................................................................................519
29.2.1.1
Wait mode....................................................................................................................................519
29.2.1.2
Stop modes...................................................................................................................................520
Block diagram..................................................................................................................................................520
29.3 External signal description..............................................................................................................................................520
29.4 Register definition...........................................................................................................................................................521
29.4.1
RTC Status and Control Register (RTC_SC)..................................................................................................521
29.4.2
RTC Modulo Register (RTC_MOD)...............................................................................................................523
29.4.3
RTC Counter Register (RTC_CNT)................................................................................................................523
29.5 Functional description.....................................................................................................................................................524
29.5.1
RTC operation example...................................................................................................................................525
29.6 Initialization/application information.............................................................................................................................526
Chapter 30
Serial Peripheral Interface (SPI)
30.1 Introduction.....................................................................................................................................................................527
30.1.1
Features............................................................................................................................................................527
30.1.2
Modes of operation..........................................................................................................................................528
30.1.3
Block diagrams................................................................................................................................................529
30.1.3.1
SPI system block diagram............................................................................................................529
30.1.3.2
SPI module block diagram...........................................................................................................529
30.2 External signal description..............................................................................................................................................531
30.2.1
SPSCK — SPI Serial Clock.............................................................................................................................531
30.2.2
MOSI — Master Data Out, Slave Data In.......................................................................................................532
30.2.3
MISO — Master Data In, Slave Data Out.......................................................................................................532
30.2.4
SS — Slave Select............................................................................................................................................532
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
27
Section number
Title
Page
30.3 Memory map/register definition.....................................................................................................................................533
30.3.1
SPI Control Register 1 (SPIx_C1)...................................................................................................................533
30.3.2
SPI Control Register 2 (SPIx_C2)...................................................................................................................535
30.3.3
SPI Baud Rate Register (SPIx_BR).................................................................................................................536
30.3.4
SPI Status Register (SPIx_S)...........................................................................................................................537
30.3.5
SPI Data Register (SPIx_D).............................................................................................................................538
30.3.6
SPI Match Register (SPIx_M)..........................................................................................................................539
30.4 Functional description.....................................................................................................................................................539
30.4.1
General.............................................................................................................................................................539
30.4.2
Master mode.....................................................................................................................................................540
30.4.3
Slave mode.......................................................................................................................................................541
30.4.4
SPI clock formats.............................................................................................................................................543
30.4.5
SPI baud rate generation..................................................................................................................................546
30.4.6
Special features................................................................................................................................................546
30.4.7
30.4.6.1
SS Output.....................................................................................................................................546
30.4.6.2
Bidirectional mode (MOMI or SISO)..........................................................................................547
Error conditions................................................................................................................................................548
30.4.7.1
30.4.8
30.4.9
Mode fault error...........................................................................................................................548
Low-power mode options................................................................................................................................549
30.4.8.1
SPI in Run mode..........................................................................................................................549
30.4.8.2
SPI in Wait mode.........................................................................................................................549
30.4.8.3
SPI in Stop mode..........................................................................................................................550
Reset.................................................................................................................................................................550
30.4.10 Interrupts..........................................................................................................................................................551
30.4.10.1
MODF..........................................................................................................................................551
30.4.10.2
SPRF............................................................................................................................................551
30.4.10.3
SPTEF..........................................................................................................................................552
30.4.10.4
SPMF...........................................................................................................................................552
30.4.10.5
Asynchronous interrupt in low-power modes..............................................................................552
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
28
Freescale Semiconductor, Inc.
Section number
Title
Page
30.5 Initialization/application information.............................................................................................................................552
30.5.1
Initialization sequence......................................................................................................................................552
30.5.2
Pseudo-Code Example.....................................................................................................................................553
Chapter 31
Inter-Integrated Circuit (I2C)
31.1 Introduction.....................................................................................................................................................................557
31.1.1
Features............................................................................................................................................................557
31.1.2
Modes of operation..........................................................................................................................................558
31.1.3
Block diagram..................................................................................................................................................558
31.2 I2C signal descriptions....................................................................................................................................................559
31.3 Memory map/register definition.....................................................................................................................................560
31.3.1
I2C Address Register 1 (I2Cx_A1)..................................................................................................................561
31.3.2
I2C Frequency Divider register (I2Cx_F)........................................................................................................561
31.3.3
I2C Control Register 1 (I2Cx_C1)...................................................................................................................562
31.3.4
I2C Status register (I2Cx_S)............................................................................................................................564
31.3.5
I2C Data I/O register (I2Cx_D).......................................................................................................................565
31.3.6
I2C Control Register 2 (I2Cx_C2)...................................................................................................................566
31.3.7
I2C Programmable Input Glitch Filter register (I2Cx_FLT)...........................................................................567
31.3.8
I2C Range Address register (I2Cx_RA)..........................................................................................................568
31.3.9
I2C SMBus Control and Status register (I2Cx_SMB).....................................................................................569
31.3.10 I2C Address Register 2 (I2Cx_A2)..................................................................................................................571
31.3.11 I2C SCL Low Timeout Register High (I2Cx_SLTH)......................................................................................571
31.3.12 I2C SCL Low Timeout Register Low (I2Cx_SLTL).......................................................................................571
31.4 Functional description.....................................................................................................................................................572
31.4.1
I2C protocol.....................................................................................................................................................572
31.4.1.1
START signal..............................................................................................................................573
31.4.1.2
Slave address transmission...........................................................................................................573
31.4.1.3
Data transfers...............................................................................................................................573
31.4.1.4
STOP signal.................................................................................................................................574
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
29
Section number
31.4.2
Title
Page
31.4.1.5
Repeated START signal...............................................................................................................574
31.4.1.6
Arbitration procedure...................................................................................................................574
31.4.1.7
Clock synchronization..................................................................................................................575
31.4.1.8
Handshaking.................................................................................................................................575
31.4.1.9
Clock stretching...........................................................................................................................575
31.4.1.10
I2C divider and hold values.........................................................................................................576
10-bit address...................................................................................................................................................577
31.4.2.1
Master-transmitter addresses a slave-receiver.............................................................................577
31.4.2.2
Master-receiver addresses a slave-transmitter.............................................................................578
31.4.3
Address matching.............................................................................................................................................578
31.4.4
System management bus specification............................................................................................................579
31.4.4.1
Timeouts.......................................................................................................................................579
31.4.4.2
FAST ACK and NACK...............................................................................................................581
31.4.5
Resets...............................................................................................................................................................582
31.4.6
Interrupts..........................................................................................................................................................582
31.4.6.1
Byte transfer interrupt..................................................................................................................583
31.4.6.2
Address detect interrupt...............................................................................................................583
31.4.6.3
Stop Detect Interrupt....................................................................................................................583
31.4.6.4
Exit from low-power/stop modes.................................................................................................583
31.4.6.5
Arbitration lost interrupt..............................................................................................................583
31.4.6.6
Timeout interrupt in SMBus........................................................................................................584
31.4.7
Programmable input glitch filter......................................................................................................................584
31.4.8
Address matching wake-up..............................................................................................................................585
31.5 Initialization/application information.............................................................................................................................586
Chapter 32
Freescale's Scalable Controller Area Network (MSCAN)
32.1 Introduction.....................................................................................................................................................................589
32.1.1
Glossary...........................................................................................................................................................589
32.1.2
Block diagram..................................................................................................................................................590
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
30
Freescale Semiconductor, Inc.
Section number
Title
Page
32.1.3
Features............................................................................................................................................................590
32.1.4
Modes of operation..........................................................................................................................................591
32.1.4.1
Normal system operating modes..................................................................................................591
32.1.4.2
Special system operating modes..................................................................................................591
32.1.4.3
Emulation modes..........................................................................................................................591
32.1.4.4
Listen-only mode.........................................................................................................................591
32.1.4.5
MSCAN initialization mode........................................................................................................592
32.2 External signal description..............................................................................................................................................593
32.2.1
CAN system.....................................................................................................................................................593
32.3 Memory map and register definition...............................................................................................................................594
32.3.1
Programmer's model of message storage.........................................................................................................594
32.3.2
MSCAN Control Register 0 (MSCAN_CANCTL0).......................................................................................598
32.3.3
MSCAN Control Register 1 (MSCAN_CANCTL1).......................................................................................601
32.3.4
MSCAN Bus Timing Register 0 (MSCAN_CANBTR0)................................................................................603
32.3.5
MSCAN Bus Timing Register 1 (MSCAN_CANBTR1)................................................................................603
32.3.6
MSCAN Receiver Flag Register (MSCAN_CANRFLG)...............................................................................605
32.3.7
MSCAN Receiver Interrupt Enable Register (MSCAN_CANRIER).............................................................607
32.3.8
MSCAN Transmitter Flag Register (MSCAN_CANTFLG)...........................................................................608
32.3.9
MSCAN Transmitter Interrupt Enable Register (MSCAN_CANTIER).........................................................609
32.3.10 MSCAN Transmitter Message Abort Request Register (MSCAN_CANTARQ)...........................................610
32.3.11 MSCAN Transmitter Message Abort Acknowledge Register (MSCAN_CANTAAK).................................611
32.3.12 MSCAN Transmit Buffer Selection Register (MSCAN_CANTBSEL)..........................................................611
32.3.13 MSCAN Identifier Acceptance Control Register (MSCAN_CANIDAC)......................................................613
32.3.14 MSCAN Miscellaneous Register (MSCAN_CANMISC)...............................................................................614
32.3.15 MSCAN Receive Error Counter (MSCAN_CANRXERR).............................................................................614
32.3.16 MSCAN Transmit Error Counter (MSCAN_CANTXERR)...........................................................................615
32.3.17 MSCAN Identifier Acceptance Register n of First Bank (MSCAN_CANIDARn)........................................615
32.3.18 MSCAN Identifier Mask Register n of First Bank (MSCAN_CANIDMRn).................................................616
32.3.19 MSCAN Identifier Acceptance Register n of Second Bank (MSCAN_CANIDARn)....................................617
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
31
Section number
Title
Page
32.3.20 MSCAN Identifier Mask Register n of Second Bank (MSCAN_CANIDMRn).............................................618
32.3.21 Receive Extended Identifier Register 0 (MSCAN_REIDR0)..........................................................................618
32.3.22 Receive Standard Identifier Register 0 (MSCAN_RSIDR0)...........................................................................619
32.3.23 Receive Extended Identifier Register 1 (MSCAN_REIDR1)..........................................................................619
32.3.24 Receive Standard Identifier Register 1 (MSCAN_RSIDR1)...........................................................................620
32.3.25 Receive Extended Identifier Register 2 (MSCAN_REIDR2)..........................................................................621
32.3.26 Receive Extended Identifier Register 3 (MSCAN_REIDR3)..........................................................................622
32.3.27 Receive Extended Data Segment Register N (MSCAN_REDSRn)................................................................622
32.3.28 Receive Data Length Register (MSCAN_RDLR)...........................................................................................623
32.3.29 Receive Time Stamp Register High (MSCAN_RTSRH)................................................................................623
32.3.30 Receive Time Stamp Register Low (MSCAN_RTSRL).................................................................................624
32.3.31 Transmit Extended Identifier Register 0 (MSCAN_TEIDR0)........................................................................625
32.3.32 Transmit Standard Identifier Register 0 (MSCAN_TSIDR0).........................................................................625
32.3.33 Transmit Extended Identifier Register 1 (MSCAN_TEIDR1)........................................................................626
32.3.34 Transmit Standard Identifier Register 1 (MSCAN_TSIDR1).........................................................................627
32.3.35 Transmit Extended Identifier Register 2 (MSCAN_TEIDR2)........................................................................628
32.3.36 Transmit Extended Identifier Register 3 (MSCAN_TEIDR3)........................................................................628
32.3.37 Transmit Extended Data Segment Register N (MSCAN_TEDSRn)...............................................................629
32.3.38 Transmit Data Length Register (MSCAN_TDLR)..........................................................................................629
32.3.39 Transmit Buffer Priority Register (MSCAN_TBPR)......................................................................................630
32.3.40 Transmit Time Stamp Register High (MSCAN_TTSRH)...............................................................................631
32.3.41 Transmit Time Stamp Register Low (MSCAN_TTSRL)................................................................................632
32.4 Functional description.....................................................................................................................................................633
32.4.1
Message storage...............................................................................................................................................633
32.4.2
Message transmit background..........................................................................................................................634
32.4.3
Transmit structures...........................................................................................................................................634
32.4.4
Receive structures............................................................................................................................................636
32.4.5
Identifier acceptance filter...............................................................................................................................637
32.4.5.1
Protocol violation protection........................................................................................................640
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
32
Freescale Semiconductor, Inc.
Section number
32.4.5.2
32.4.6
Title
Page
Clock system................................................................................................................................641
Low-power options..........................................................................................................................................643
32.4.6.1
Operation in run mode.................................................................................................................644
32.4.6.2
Operation in wait mode................................................................................................................644
32.4.6.3
Operation in stop mode................................................................................................................644
32.4.6.4
MSCAN normal mode.................................................................................................................644
32.4.6.5
MSCAN sleep mode....................................................................................................................645
32.4.6.6
MSCAN power down mode.........................................................................................................646
32.4.6.7
Disabled mode..............................................................................................................................647
32.4.6.8
Programmable wake-Up function................................................................................................647
32.4.7
Reset initialization............................................................................................................................................647
32.4.8
Interrupts..........................................................................................................................................................647
32.4.9
32.4.8.1
Description of interrupt operation................................................................................................648
32.4.8.2
Transmit interrupt........................................................................................................................648
32.4.8.3
Receive interrupt..........................................................................................................................648
32.4.8.4
Wake-up interrupt........................................................................................................................648
32.4.8.5
Error interrupt..............................................................................................................................649
32.4.8.6
Interrupt acknowledge..................................................................................................................649
Initialization/Application information.............................................................................................................649
32.4.9.1
MSCAN initialization..................................................................................................................649
32.4.9.2
Bus-off recovery..........................................................................................................................650
Chapter 33
Universal Asynchronous Receiver/Transmitter (UART)
33.1 Introduction.....................................................................................................................................................................651
33.1.1
Features............................................................................................................................................................651
33.1.2
Modes of operation..........................................................................................................................................651
33.1.3
Block diagram..................................................................................................................................................652
33.2 UART signal descriptions...............................................................................................................................................654
33.2.1
Detailed signal descriptions.............................................................................................................................654
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
33
Section number
Title
Page
33.3 Register definition...........................................................................................................................................................654
33.3.1
UART Baud Rate Register: High (UARTx_BDH)..........................................................................................655
33.3.2
UART Baud Rate Register: Low (UARTx_BDL)...........................................................................................656
33.3.3
UART Control Register 1 (UARTx_C1).........................................................................................................657
33.3.4
UART Control Register 2 (UARTx_C2).........................................................................................................658
33.3.5
UART Status Register 1 (UARTx_S1)............................................................................................................660
33.3.6
UART Status Register 2 (UARTx_S2)............................................................................................................661
33.3.7
UART Control Register 3 (UARTx_C3).........................................................................................................663
33.3.8
UART Data Register (UARTx_D)...................................................................................................................664
33.4 Functional description.....................................................................................................................................................665
33.4.1
Baud rate generation........................................................................................................................................665
33.4.2
Transmitter functional description...................................................................................................................666
33.4.2.1
33.4.3
Send break and queued idle.........................................................................................................667
Receiver functional description.......................................................................................................................668
33.4.3.1
Data sampling technique..............................................................................................................669
33.4.3.2
Receiver wake-up operation.........................................................................................................669
33.4.4
Interrupts and status flags................................................................................................................................671
33.4.5
Baud rate tolerance...........................................................................................................................................672
33.4.6
33.4.5.1
Slow data tolerance......................................................................................................................672
33.4.5.2
Fast data tolerance........................................................................................................................673
Additional UART functions.............................................................................................................................674
33.4.6.1
8- and 9-bit data modes................................................................................................................675
33.4.6.2
Stop mode operation....................................................................................................................675
33.4.6.3
Loop mode...................................................................................................................................675
33.4.6.4
Single-wire operation...................................................................................................................676
Chapter 34
General-Purpose Input/Output (GPIO)
34.1 Introduction.....................................................................................................................................................................677
34.1.1
Features............................................................................................................................................................677
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
34
Freescale Semiconductor, Inc.
Section number
Title
Page
34.1.2
Modes of operation..........................................................................................................................................677
34.1.3
GPIO signal descriptions.................................................................................................................................678
34.1.3.1
Detailed signal description...........................................................................................................678
34.2 Memory map and register definition...............................................................................................................................679
34.2.1
GPIO/FGPIO register bits assignment.............................................................................................................679
34.2.2
Port Data Output Register (GPIOx_PDOR).....................................................................................................681
34.2.3
Port Set Output Register (GPIOx_PSOR)........................................................................................................682
34.2.4
Port Clear Output Register (GPIOx_PCOR)....................................................................................................682
34.2.5
Port Toggle Output Register (GPIOx_PTOR).................................................................................................683
34.2.6
Port Data Input Register (GPIOx_PDIR).........................................................................................................683
34.2.7
Port Data Direction Register (GPIOx_PDDR).................................................................................................684
34.2.8
Port Input Disable Register (GPIOx_PIDR)....................................................................................................684
34.3 FGPIO memory map and register definition..................................................................................................................684
34.3.1
GPIO/FGPIO register bits assignment.............................................................................................................685
34.3.2
Port Data Output Register (FGPIOx_PDOR)..................................................................................................687
34.3.3
Port Set Output Register (FGPIOx_PSOR).....................................................................................................687
34.3.4
Port Clear Output Register (FGPIOx_PCOR).................................................................................................688
34.3.5
Port Toggle Output Register (FGPIOx_PTOR)...............................................................................................688
34.3.6
Port Data Input Register (FGPIOx_PDIR).......................................................................................................689
34.3.7
Port Data Direction Register (FGPIOx_PDDR)..............................................................................................689
34.3.8
Port Input Disable Register (FGPIOx_PIDR)..................................................................................................690
34.4 Functional description.....................................................................................................................................................690
34.4.1
General-purpose input......................................................................................................................................690
34.4.2
General-purpose output....................................................................................................................................690
34.4.3
IOPORT...........................................................................................................................................................691
Chapter 35
Keyboard Interrupts (KBI)
35.1 Introduction.....................................................................................................................................................................693
35.1.1
Features............................................................................................................................................................693
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
35
Section number
35.1.2
35.1.3
Title
Page
Modes of Operation.........................................................................................................................................693
35.1.2.1
KBI in Wait mode........................................................................................................................693
35.1.2.2
KBI in Stop modes.......................................................................................................................694
Block Diagram.................................................................................................................................................694
35.2 External signals description............................................................................................................................................694
35.3 Register definition...........................................................................................................................................................695
35.4 Memory Map and Registers............................................................................................................................................695
35.4.1
KBI Pin Enable Register (KBIx_PE)...............................................................................................................696
35.4.2
KBI Edge Select Register (KBIx_ES).............................................................................................................696
35.4.3
KBI Status and Control Register (KBIx_SC)..................................................................................................697
35.4.4
KBI Source Pin Register (KBIx_SP)...............................................................................................................698
35.5 Functional Description....................................................................................................................................................698
35.5.1
Edge-only sensitivity........................................................................................................................................699
35.5.2
Edge and level sensitivity................................................................................................................................699
35.5.3
KBI Pullup Resistor.........................................................................................................................................699
35.5.4
KBI initialization..............................................................................................................................................700
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
36
Freescale Semiconductor, Inc.
Chapter 1
About This Document
1.1 Overview
1.1.1 Purpose
This document describes the features, architecture, and programming model of the
Freescale KE06 microcontroller.
1.1.2 Audience
This document is primarily for system architects and software application developers
who are using or considering using the KE06 microcontroller in a system.
1.2 Conventions
1.2.1 Numbering systems
The following suffixes identify different numbering systems:
This suffix
Identifies a
b
Binary number. For example, the binary equivalent of the
number 5 is written 101b. In some cases, binary numbers are
shown with the prefix 0b.
d
Decimal number. Decimal numbers are followed by this suffix
only when the possibility of confusion exists. In general,
decimal numbers are shown without a suffix.
h
Hexadecimal number. For example, the hexadecimal
equivalent of the number 60 is written 3Ch. In some cases,
hexadecimal numbers are shown with the prefix 0x.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
37
Conventions
1.2.2 Typographic notation
The following typographic notation is used throughout this document:
Example
Description
placeholder, x
Items in italics are placeholders for information that you provide. Italicized text is also used for
the titles of publications and for emphasis. Plain lowercase letters are also used as
placeholders for single letters and numbers.
code
Fixed-width type indicates text that must be typed exactly as shown. It is used for instruction
mnemonics, directives, symbols, subcommands, parameters, and operators. Fixed-width type
is also used for example code. Instruction mnemonics and directives in text and tables are
shown in all caps; for example, BSR.
SR[SCM]
A mnemonic in brackets represents a named field in a register. This example refers to the
Scaling Mode (SCM) field in the Status Register (SR).
REVNO[6:4], XAD[7:0]
Numbers in brackets and separated by a colon represent either:
• A subset of a register's named field
For example, REVNO[6:4] refers to bits 6–4 that are part of the COREREV field that
occupies bits 6–0 of the REVNO register.
• A continuous range of individual signals of a bus
For example, XAD[7:0] refers to signals 7–0 of the XAD bus.
1.2.3 Special terms
The following terms have special meanings:
Term
Meaning
asserted
Refers to the state of a signal as follows:
• An active-high signal is asserted when high (1).
• An active-low signal is asserted when low (0).
deasserted
Refers to the state of a signal as follows:
• An active-high signal is deasserted when low (0).
• An active-low signal is deasserted when high (1).
In some cases, deasserted signals are described as negated.
reserved
Refers to a memory space, register, or field that is either
reserved for future use or for which, when written to, the
module or chip behavior is unpredictable.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
38
Freescale Semiconductor, Inc.
Chapter 2
Introduction
2.1 Overview
This chapter provides an overview of the Kinetis KE06 product family of ARM®
Cortex®-M0+ MCUs. It also presents high-level descriptions of the modules available on
the devices covered by this document.
2.2 Module functional categories
The modules on this device are grouped into functional categories. The following
sections describe the modules assigned to each category in more detail.
Table 2-1. Module functional categories
Module category
Description
ARM Cortex-M0+ core
• 32-bit MCU core from ARM’s Cortex-M class, 1.77 CoreMark®/MHz from
single-cycle access memories, 48 MHz CPU frequency
System
•
•
•
•
•
•
Memories
• Internal memories include:
• Up to 128 KB flash memory
• Up to 16 KB SRAM
Clocks
• External crystal oscillator or resonator
• Low range: 31.25–39.0625 kHz
• High range: 4– 24 MHz
• External square wave input clock
• Internal clock references
• 31.25 to 39.0625 kHz oscillator
• 1 kHz LPO oscillator
• Frequency-locked loop (FLL) range: 40–50 MHz
System integration module (SIM)
Power management and mode controllers (PMC)
Miscellaneous control module (MCM)
Bit manipulation engine (BME)
Peripheral bridge (AIPS)
Watchdog (WDOG)
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
39
Module functional categories
Table 2-1. Module functional categories (continued)
Module category
Description
Security
• Watchdog (WDOG) with independent clock source
• Cyclic redundancy check (CRC) module for error detection
Analog
• One 12-bit analog-to-digital converters (ADC) with up to 16 channels
• Two analog comparators (ACMP) with internal 6-bit digital-to-analog
converter (DAC)
Timers
•
•
•
•
•
•
One 6-channel FlexTimer (FTM) with full function
Two 2-channel FTMs with basic TPM function
2-channel periodic interrupt timer (PIT)
Real time clock (RTC)
One pulse width timer (PWT)
System tick timer (SysTick)
Communications
•
•
•
•
Two 8-bit serial peripheral interfaces (SPI)
Two inter-integrated circuit (I2C) modules
Three universal asynchronous receiver/transmitter (UART) modules
One Freescale's scalable controller area network (MSCAN)
Human-Machine Interfaces (HMI)
• General purpose input/output (GPIO) controller
• Two keyboard Interrupt (KBI)
• Interrupt (IRQ)
2.2.1 ARM Cortex-M0+ core modules
The following core modules are available on this device.
Table 2-2. Core modules
Module
Description
ARM Cortex-M0+
The ARM Cortex-M0+ is the newest member of the Cortex M Series of processors
targeting microcontroller applications focused on very cost sensitive, deterministic,
interrupt driven environments. The Cortex M0+ processor is based on the ARMv6
Architecture and Thumb®-2 ISA and is 100% instruction set compatible with its
predecessor, the Cortex-M0 core, and upward compatible to Cortex-M3 and M4
cores.
The ARM Cortex-M0+ improvements include an ARMv6 Thumb-2 DSP, ported
from the ARMv6-A/R profile architectures, that provide 32-bit instructions with
SIMD (single instruction multiple data) DSP style multiply-accumulates and
saturating arithmetic to support single cycle 32x32 multiplier.
Nested vectored interrupt controller
(NVIC)
The ARMv6-M exception model and nested-vectored interrupt controller (NVIC)
implement a relocatable vector table supporting many external interrupts, a single
non-maskable interrupt (NMI), and priority levels.
The NVIC replaces shadow registers with equivalent system and simplified
programmability. The NVIC contains the address of the function to execute for a
particular handler. The address is fetched via the instruction port allowing parallel
register stacking and look-up. The first sixteen entries are allocated to ARM
internal sources with the others mapping to MCU-defined interrupts.
Asynchronous wakeup interrupt
controller (AWIC)
The primary function of the Asynchronous Wake-up Interrupt Controller (AWIC) is
to detect asynchronous wake-up events in stop modes and signal to clock control
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
40
Freescale Semiconductor, Inc.
Chapter 2 Introduction
Table 2-2. Core modules (continued)
Module
Description
logic to resume system clocking. After clock restart, the NVIC observes the
pending interrupt and performs the normal interrupt or event processing.
Single-cycle I/O port (IOPORT)
For high-speed, single-cycle access to peripherals, the Cortex-M0+ processor
implements a dedicated single-cycle I/O port. On this device, fast GPIO (FGPIO) is
implemented on IOPORT interface.
Debug interfaces
Most of this device's debug is based on the ARM CoreSight™ architecture. One
debug interface is supported:
• Serial Wire Debug (SWD)
2.2.2 System modules
The following system modules are available on this device.
Table 2-3. System modules
Module
Description
System integration module (SIM)
The SIM includes integration logic and several module configuration settings.
Power management controller (PMC)
The PMC provides the user with multiple power options. Multiple modes are
supported that allow the user to optimize power consumption for the level of
functionality needed. Includes power-on-reset (POR) and integrated low voltage
detect (LVD) with reset (brownout) capability and selectable LVD trip points.
Miscellaneous control module (MCM)
The MCM includes integration logic and details.
Peripheral bridge (AIPS-Lite)
The peripheral bridge converts the ARM AHB interface to an interface to access a
majority of peripherals on the device.
Watchdog (WDOG)
The WDOG monitors internal system operation and forces a reset in case of
failure. It can run from an independent 1 kHz low-power oscillator with a
programmable refresh window to detect deviations in program flow or system
frequency.
Bit manipulation engine (BME)
The BME provides hardware support for atomic read-modify-write memory
operations to the peripheral address space in Cortex-M0+ based microcontrollers.
2.2.3 Memories and memory interfaces
The following memories and memory interfaces are available on this device.
Table 2-4. Memories and memory interfaces
Module
Description
Flash memory (FTMRE)
Flash memory — up to 128 KB of the non-volatile flash memory that can execute
program code.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
41
Module functional categories
Table 2-4. Memories and memory interfaces (continued)
Module
Description
Flash memory controller (FMC)
FMC is a memory acceleration unit that provides an interface between Cortex M0+
core and the 32-bit program flash memory. The FMC contains one 32-bit
speculation buffer and one 32-byte cache that can accelerate instruction fetch and
flash access.
SRAM
Up to 16 KB internal system RAM, supporting bit operation through BME module or
aliased bit-band domain.
2.2.4 Clocks
The following clock modules are available on this device.
Table 2-5. Clock modules
Module
Description
Internal Clock Source (ICS)
ICS module containing an internal reference clock (ICSIRCLK) and a frequencylocked-loop (FLL).
System oscillator (OSC)
The system oscillator, in conjunction with an external crystal or resonator,
generates a reference clock for the MCU.
Low-Power Oscillator (LPO)
The PMC module contains a 1 kHz low-power oscillator which acts as a standalone
low-frequency clock source in all modes.
2.2.5 Security and integrity modules
The following security and integrity modules are available on this device:
Table 2-6. Security and integrity modules
Module
Description
Cyclic Redundancy Check (CRC)
CRC generates 16/32-bit CRC code for error detection.
Watchdog (WDOG)
The WDOG monitors internal system operation and forces a reset in case of
failure. It can run from an independent 1 kHz low-power oscillator with a
programmable refresh window to detect deviations in program flow or system
frequency.
2.2.6 Analog modules
The following analog modules are available on this device:
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
42
Freescale Semiconductor, Inc.
Chapter 2 Introduction
Table 2-7. Analog modules
Module
Description
Analog-to-digital converters (ADC)
12-bit successive-approximation ADC module with up to 16 channels.
Analog comparators (ACMP)
Two comparators with support of analog input voltages across the full range of the
supply voltage and CPU interrupt. ACMP0/1 is further capable to trigger an ADC
acquisition and FTM update.
6-bit digital-to-analog converters (DAC)
64-tap resistor ladder network which provides a selectable voltage reference for
comparator.
2.2.7 Timer modules
The following timer modules are available on this device:
Table 2-8. Timer modules
Module
Description
FlexTimer modules (FTM)
• Selectable FTM source clock, supporting separate timer clock up to 48 MHz,
programmable prescaler
• 16-bit counter supporting free-running or initial/final value, and counting is up
or up-down
• Input capture, output compare, and edge-aligned and center-aligned PWM
modes
• Operation of FTM channels as pairs with equal outputs, pairs with
complementary outputs, or independent channels with independent outputs
• Deadtime insertion is available for each complementary pair
• Software control of PWM outputs
• Up to two fault inputs for global fault control
• Configurable channel polarity
• Programmable interrupt on input capture, reference compare, overflowed
counter, or detected fault condition
Periodic interrupt timers (PIT)
•
•
•
•
Real-time counter (RTC)
• 16-bit up-counter
• 16-bit modulo match limit
• Software controllable periodic interrupt on match
• Software selectable clock sources for input to prescaler with programmable
16-bit prescaler
• Bus clock
• IRC clock (31.25~39.0625 kHz)
• LPO (~1 kHz)
• System oscilator output clock
Pulse Width Timer (PWT)
•
•
•
•
One general purpose interrupt timer
Interrupt timers for triggering ADC conversions
32-bit counter resolution
Clocked by bus clock frequency
Automatic measurement of pulse width with 16-bit resolution
Separate positive and negative pulse width measurements
Programmable triggering edge for starting measurement
Programmable measuring time between successive alternating edges, rising
edges or falling edges
• Programmable pre-scaler from clock input as 16-bit counter time base
• Two selectable clock sources, supporting separate timer clock up to 48 MHz
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
43
Module functional categories
Table 2-8. Timer modules
Module
Description
• Four selectable pulse inputs
• Programmable interrupt generation upon pulse width value updated and
counter overflow
2.2.8 Communication interfaces
The following communication interfaces are available on this device:
Table 2-9. Communication modules
Module
Description
Serial peripheral interface (SPI)
Two SPIs synchronous serial bus for communication to an external device.
Inter-integrated circuit (I2C)
Two I2C modules for inter device communications. Also support the System
Management Bus (SMBus) Specification, version 2. I2C0 supports four wire
interface feature.
Universal asynchronous receiver/
transmitters (UART)
Three asynchronous serial bus communication interfaces (UART) modules with
optional 13-bit break, full duplex non-return to zero (NRZ), and LIN extension
support.
Freescale's scalable controller area
network (MSCAN)
One Freescale's scalable controller area network (MSCAN).
2.2.9 Human-machine interfaces
The following human-machine interfaces (HMI) are available on this device:
Table 2-10. HMI modules
Module
Description
General purpose input/output (GPIO)
Up to 71 general purpose input or output (GPIO) pins.
Keyboard Interrupts (KBI)
Two KBI modules to support pin interrupts.
Interrupt (IRQ)
IRQ module provides a maskable interrupt input.
2.2.10 Orderable part numbers
The following table summarizes the part numbers of the devices covered by this
document.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
44
Freescale Semiconductor, Inc.
Chapter 2 Introduction
Table 2-11. Orderable part numbers summary
Freescale part number
CPU
frequency
Pin count
Package
Total flash
memory
RAM
Temperature range
MKE06Z64VLD4(R)
48 MHz
44
LQFP
64 KB
8 KB
-40 to 105 °C
MKE06Z128VLD4(R)
48 MHz
44
LQFP
128 KB
16 KB
-40 to 105 °C
MKE06Z64VQH4(R)
48 MHz
64
QFP
64 KB
8 KB
-40 to 105 °C
MKE06Z128VQH4(R)
48 MHz
64
QFP
128 KB
16 KB
-40 to 105 °C
MKE06Z64VLH4(R)
48 MHz
64
LQFP
64 KB
8 KB
-40 to 105 °C
MKE06Z128VLH4(R)
48 MHz
64
LQFP
128 KB
16 KB
-40 to 105 °C
MKE06Z64VLK4(R)
48 MHz
80
LQFP
64 KB
8 KB
-40 to 105 °C
MKE06Z128VLK4(R)
48 MHz
80
LQFP
128 KB
16 KB
-40 to 105 °C
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
45
Module functional categories
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
46
Freescale Semiconductor, Inc.
Chapter 3
Chip Configuration
3.1 Introduction
This chapter provides details on the individual modules of the microcontroller. It
includes:
• Module block diagrams showing immediate connections within the device
• Specific module-to-module interactions not necessarily discussed in the individual
module chapters
• Links for more information
3.2 Module to Module Interconnects
3.2.1 Interconnection overview
The following table captures the module-to-module interconnections for this device.
Table 3-1. Module-to-module interconnects
Peripheral
Signal
—
to Peripheral
Use Case
Control
Comm
ent
FTM2
INITTRG,
MatchTRG
to
ADC (Trigger)
ADC Triggering
SIM_SOPT0[ADHWT]
—
PIT CHx
TIF0,TIF1
to
ADC (Trigger)
ADC Triggering
SIM_SOPT0[ADHWT]
—
RTC
RTC Overflow
to
ADC (Trigger)
ADC Triggering
SIM_SOPT0[ADHWT]
—
FTM0
INITTRG
to
ADC (Trigger)
ADC Triggering
SIM_SOPT0[ADHWT]
—
ACMP0
CMP0_OUT
to
ADC (Trigger)
ADC Triggering
SIM_SOPT0[ADHWT]
—
ACMP1
CMP1_OUT
to
ADC (Trigger)
ADC Triggering
SIM_SOPT0[ADHWT]
—
UART0
TX0
to
Modulated by
FTM0 CH0
UART modulation
SIM_SOPT0[TXDME]
—
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
47
Module to Module Interconnects
Table 3-1. Module-to-module interconnects (continued)
Peripheral
Signal
—
to Peripheral
Use Case
Control
Comm
ent
UART0
RX0
to
FTM0 CH1 input
capture
UART modulation
SIM_SOPT0[RXDCE]
—
ACMP0
CMP0_OUT
to
UART0 RxD
UART RxD Filter
SIM_SOPT0[RXDFE]
—
ACMP1
CMP1_OUT
to
UART0 RxD
UART RxD Filter
SIM_SOPT0[RXDFE]
—
ACMP0
CMP0_OUT
to
FTM1 CH0 input
capture
ACMP0 output
capture
SIM_SOPT0[ACIC]
—
RTC
RTC overflow
to
FTM1 CH1 input
capture
RTC overflow
capture
SIM_SOPT0[RTCC]
—
ACMP0
CMP0_OUT
to
FTM2 Trigger0
FTM2 Trigger input
SIM_SOPT0[ACTRG] &
FTM2_SYNC[TRIG0]
—
ACMP1
CMP1_OUT
to
FTM2 Trigger0
FTM2 Trigger input
SIM_SOPT0[ACTRG] &
FTM2_SYNC[TRIG0]
—
FTM0
FTM0 CH0
Output
to
FTM2 Trigger1
FTM2 Trigger input
FTM2_SYNC[TRIG1]
—
SIM
FTMSYNC
to
FTM2 Trigger2
FTM2 Trigger input
FTM2_SYNC[TRIG2]
—
ACMP0
CMP0_OUT
to
FTM2 Fault0
FTM2 fault input
FTM2_FLTCTRL[FAULT0EN]
—
EXTFT_IN
EXTFT_IN
to
FTM2 Fault1
FTM2 fault input
FTM2_FLTCTRL[FAULT1EN]
PTA6
EXTFT_IN
EXTFT_IN
to
FTM2 Fault2
FTM2 fault input
FTM2_FLTCTRL[FAULT2EN]
PTA7
ACMP1
CMP1_OUT
to
FTM2 Fault3
FTM2 fault input
FTM2_FLTCTRL[FAULT3EN]
—
EXT_PWT_I
N0
PWT_IN0
to
PWT
PWT_IN0
SIM_PINSEL1[PWTIN0PS] &
PWT_R1[PINSEL]
PTD5
or PTE2
EXT_PWT_I
N1
PWT_IN1
to
PWT
PWT_IN1
SIM_PINSEL1[PWTIN1PS] &
PWT_R1[PINSEL]
PTB0 or
PTH7
ACMP0
ACMP0_OUT
to
PWT
PWT_IN2
SIM_SOPT1[ACPWTS] &
PWT_R1[PINSEL]
—
ACMP1
ACMP1_OUT
to
PWT
PWT_IN2
SIM_SOPT1[ACPWTS] &
PWT_R1[PINSEL]
—
UART0
RX
to
PWT
PWT_IN3
SIM_SOPT1[UARTPWTS] &
PWT_R1[PINSEL]
—
UART1
RX
to
PWT
PWT_IN3
SIM_SOPT1[UARTPWTS] &
PWT_R1[PINSEL]
—
UART2
RX
to
PWT
PWT_IN3
SIM_SOPT1[UARTPWTS] &
PWT_R1[PINSEL]
—
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
48
Freescale Semiconductor, Inc.
Chapter 3 Chip Configuration
+
ACMP1
–
+
ACMP0
–
ADC
trg
ovf
RTC
tif
PITch0
tif
PITch1
inittrg
0
ovf
ICSCLK
ADHWT[2:0]
DELAY
1
2N
1
FTM0
inittrg
fault0
matchtrg fault1
fault2
FTM2 fault3
trigger0
trigger1
trigger2
BUSREF
Figure 3-1. ADC hardware trigger connection diagram
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
49
Module to Module Interconnects
+
ACMP1
–
RXDFE
+
ACMP0
UART0
–
rxd
RX0
txd
0
TX0
1
tof FTM0
FTM0CH0
ch0
ch1
1
0
FTM0CH1
TXDME
RXDCE
ACIC
RTC
ovf
1
tof FTM1
0
ch0
ch1
FTM1CH0
1
0
FTM1CH1
RTCC
Figure 3-2. FTMx/ACMPx/UARTx connection diagram
+
ACMP0
FTM0
–
ch0
ch1
+
ACMP1
To ADC
0
1
–
inittrg
fault0
matchtrg fault1
fault2
FTM2 fault3
trigger0
trigger1
trigger2
FTM2fault1
FTM2fault2
0
1
ACTRG
FTMSYNC
Figure 3-3. FTM2 inteconnection diagram
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
50
Freescale Semiconductor, Inc.
Chapter 3 Chip Configuration
PWTIN0
PWTIN0
PWTIN1
PWTIN1
+
ACMP0
–
PWT
PWTIN2
+
ACMP1
–
PWTIN3
UART0 RX
UART1 RX
UART2 RX
ACPWTS
UARTPWTS
Figure 3-4. PWT inteconnection diagram
3.2.2 Analog reference options
Several analog blocks have selectable reference voltages as shown in Table 3-2. These
options allow analog peripherals to share or have separate analog references. Care must
be taken when selecting analog references to avoid cross talk noise.
Table 3-2. Analog reference options
Module
12-bit ADC
ACMP0
ACMP1
Reference option
Comment/ reference selection
• VREFH
• VREFL
To improve ADC performance, VREFH pin is available on 80LQFP and it
is internally connected to VDDA on 64QFP/LQFP, 44LQFP, VREFL pin is
available on every package.
• VDDA
• Bandgap
Selected by ACMP0_C1[DACREF] or ACMP1_C1[DACREF]
3.2.3 ACMP output capture
When set, the SIM_SOPT0[ACIC] bit enables the output of ACMP0 to connect to the
FTM1_CH0, the FTM1_CH0 pin is released to other shared functions.
When setting the SIM_SOPT0[RXDFE] to 01b, the ACMP0 outputs can be selected to
connect to the receiver channel of UART0. When setting the SIM_SOPT0[RXDFE] to
10b, the ACMP1 outputs can be selected to connect to the receiver channel of UART1.
ACMP0 and ACMP1 output is also connected to PWT input2(PWT_IN2), or can be used
as FTM2 trigger/fault input and ADC hardware trigger.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
51
Module to Module Interconnects
3.2.4 UART0_TX modulation
UART0_TX can be modulated by FTM0 channel 0 output. When SIM_SOPT0[TXDME]
is set, the UART0_TX is gated by FTM0 channel0 output through an AND gate, and then
mapped to UART0_TX pinout. When this field is clear, the UART0_TX is directly
mapped on the pinout. To enable IR modulation function, both FTM0_CH0 and UART
must be active. The FTM0_CNT and FTM0_MOD registers specify the period of the
PWM, and the FTM0_C0V register specifies the duty cycle of the PWM. Then, when
SIM_SOPT0[TXDME] is enabled, each data transmitted via UART0_TX from UART0
is modulated by the FTM0 channel 0 output, and the FTM0_CH0 pin is released to other
shared functions regardless of the configuration of FTM0 pin reassignment.
UART0
TX
0
UART0_TX
1
FTM0_CH0
PORT LOGIC
TXDME
Figure 3-5. IR modulation diagram
3.2.5 UART0/1/2_RX capture
UART0_RX pin is selectable connected to UART0 module directly or tagged to FTM0
channel 1. When SIM_SOPT0[RXDCE] is set, the UART0_RX pin is connected to both
UART0 and FTM0 channel 1, and the FTM0_CH1 pin is released to other shared
functions regardless of the configuration of FTM0 pin reassignment. When this field is
clear, the UART0_RX pin is connected to UART0 only.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
52
Freescale Semiconductor, Inc.
Chapter 3 Chip Configuration
RX
UART0
UART0_RX
1
FTM0_CH1
FTM0_CH1
0
RXDCE
Figure 3-6. UART0_RX capture function diagram
RX signal of UART0, UART1 and UART2 can be captured by PWT. By configuring
SIM_SOPT1[UARTPWTS], UART0_RX, UART1_RX or UART2_RX can be
connected to PWT input 3.
3.2.6 UART0_RX filter
When SIM_SOPT0[RXDFE] is clear, the UART0_RX pin is connected to UART0
module directly. When this field is correctly set, the ACMP0 output can be connected to
the receive channel of UART0. To enable UART0_RX filter function, both UART0 and
ACMP0 must be active. If this function is active, the UART0 external UART0_RX pin is
released to other shared functions regardless of the configuration of UART0 pin
reassignment. When UART0_RX capture function is active, the ACMP0 output is
injected to FTM0 channel 1 as well.
UART0_RX
0
RX
UART0
1
2
ACMP0
++
+
ACMP1
To UART0_RX
Capture Function
RXDFE
From Internal or External
Reference Voltage
Figure 3-7. IR demodulation diagram
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
53
Module to Module Interconnects
3.2.7 RTC capture
RTC overflow may be captured by FTM1 channel 1 by setting SIM_SOPT0[RTCC] bit.
When this bit is set, the RTC overflow is connected to FTM1 channel 1 for capture, the
FTM1_CH1 pin is released to other shared functions.
3.2.8 FTM2 software synchronization
FTM2 contains three synchronization input triggers, one of which is a software trigger by
writing 1 to SIM_SOPT0[FTMSYNC]. Writing 0 to this field takes no effect. This field
is always read 0.
3.2.9 ADC hardware trigger
ADC module may initiate a conversion via a hardware trigger. The following table shows
the available ADC hardware trigger sources by setting SIM_SOPT0[ADHWT].
Table 3-3. ADC hardware trigger setting
ADHWT
ADC hardware trigger
000
RTC overflow
001
FTM0 init trigger
010
FTM2 init trigger with 8-bit programmable delay
011
FTM2 match trigger with 8-bit programmable delay
100
PIT ch0 overflow
101
PIT ch1 overflow
110
ACMP0 out
111
ACMP1 out
When ADC hardware trigger selects the output of FTM2 triggers, an 8-bit delay block
will be enabled. This logic delays any trigger from FTM2 with an 8-bit counter whose
value is specified by SIM_SOPT0[DELAY]. The reference clock to this module is the
bus clock with selectable predivider specified by SIM_SOPT0[BUSREF].
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
54
Freescale Semiconductor, Inc.
Chapter 3 Chip Configuration
3.3 Core Modules
3.3.1 ARM Cortex-M0+ core configuration
This section summarizes how the module has been configured in the chip. Full
documentation for this module is provided by ARM and can be found at arm.com.
Debug
Crossbar
switch
Interrupts
ARM Cortex-M0+
Core
Figure 3-8. Core configuration
Table 3-4. Reference links to related information
Topic
Related module
Reference
Full description
ARM Cortex-M0+ core,
r0p0
ARM Cortex-M0+ Technical Reference Manual, r0p0
System memory map
System memory map
Clocking
Clock distribution
Power management
Power management
System/instruction/data
bus module
Crossbar switch
Crossbar switch
Debug
Serial Wire Debug
(SWD)
Debug
Interrupts
Nested Vectored
Interrupt Controller
(NVIC)
NVIC
Miscellaneous Control
Module (MCM)
MCM
3.3.1.1 ARM Cortex M0+ core
The ARM Cortex M0+ parameter settings are as follows:
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
55
Core Modules
Table 3-5. ARM Cortex-M0+ parameter settings
Parameter
Verilog name
Value
Description
Arch Clock Gating
ACG
1 = Present
DAP Slave Port
Support
AHBSLV
1
DAP ROM Table Base
BASEADDR
0xF000_2003
Endianess
BE
0
Little endian control for data transfers
Breakpoints
BKPT
2
Implements 2 breakpoints
Implements architectural clock gating
Supports any AHB debug access port (like the
CM4 DAP)
Base address for DAP ROM table
Debug Support
DBG
1 = Present
—
Halt Event Support
HALTEV
1 = Present
—
I/O Port
IOP
1 = Present
Implements single-cycle ld/st accesses to special
addr space
IRQ Mask Enable
IRQDIS
0x0
—
Debug Port Protocol
JTAGnSW
0 = SWD
Core Memory
Protection
MPU
0 = Absent
Number of IRQs
NUMIRQ
32
Reset all regs
RAR
0 = Standard
Do not force all registers to be async reset
Multiplier
SMUL
0 = Fast Mul
Implements single-cycle multiplier
Multi-drop Support
SWMD
0 = Absent
Do not include serial wire support for multi-drop
System Tick Timer
SYST
1 = Present
Implements system tick timer (for CM4
compatibility)
DAP Target ID
TARGETID
0
User/Privileged
USER
1 = Present
Implements processor operating modes
Vector Table Offset
Register
VTOR
1 = Present
Implements relocation of exception vector table
WIC Support
WIC
1 = Present
Implements WIC interface
WIC Requests
WICLINES
34
Exact number of wakeup IRQs is 34
Watchpoints
WPT
2
Implements 2 watchpoints
SWD protocol, not JTAG
No MPU
Assume full NVIC request vector
—
For details on the ARM Cortex-M0+ processor core see the ARM website: arm.com.
3.3.1.2 Buses, interconnects, and interfaces
The ARM Cortex-M0+ core has two bus interfaces:
• Single 32-bit AMBA-3 AHB-Lite system interface that provides connections to
peripherals and all system memory, which includes flash and RAM.
• Single 32-bit I/O port bus (IOPORT) interfacing to the FGPIO with 1-cycle loads
and stores.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
56
Freescale Semiconductor, Inc.
Chapter 3 Chip Configuration
3.3.1.3 System Tick Timer
The CLKSOURCE field in SysTick Control and Status register selects either the core
clock (when CLKSOURCE = 1) or a divide-by-16 of the core clock (when
CLKSOURCE = 0). Because the timing reference is a variable frequency, the TENMS
field in the SysTick Calibration Value Register is always zero.
3.3.1.4 Core privilege levels
The core on this device is implemented with both privileged and unprivileged levels. The
ARM documentation uses different terms than this document to distinguish between
privilege levels.
If you see this term...
it also means this term...
Privileged
Supervisor
Unprivileged or user
User
3.3.1.5 Caches
This device does not have processor related cache memories, but the flash controller has
an internal 32-byte cache for flash access.
3.3.2 Nested Vectored Interrupt Controller (NVIC) configuration
ARM Cortex-M0+
core
This section summarizes how the module has been configured in the chip. Full
documentation for this module is provided by ARM and can be found at arm.com.
Interrupts
Nested Vectored
Interrupt Controller
(NVIC)
PPB
Module
Module
Module
Figure 3-9. NVIC configuration
Table 3-6. Reference links to related information
Topic
Related module
Reference
Full description
Nested Vectored
Interrupt Controller
(NVIC)
ARM Cortex-M0+ Technical Reference Manual
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
57
Core Modules
Table 3-6. Reference links to related information (continued)
Topic
Related module
Reference
System memory map
—
System memory map
Clocking
—
Clock distribution
Power management
Power management
Private Peripheral Bus
(PPB)
ARM Cortex-M0+ core
ARM Cortex-M0+ core
3.3.2.1 Interrupt priority levels
This device supports four priority levels for interrupts. Therefore in the NVIC, each
source in the IPR registers contains two bits. For example, IPR0 is shown below:
31
R
W
30
IRQ3
29
28
27
26
25
24
0
0
0
0
0
0
23
22
IRQ2
21
20
19
18
17
16
0
0
0
0
0
0
15
14
IRQ1
13
12
11
10
9
8
0
0
0
0
0
0
7
6
IRQ0
5
4
3
2
1
0
0
0
0
0
0
0
3.3.2.2 Non-maskable interrupt
The non-maskable interrupt request to the NVIC is controlled by the external NMI signal.
The pin, which the NMI signal is multiplexed on, must be configured for the NMI
function to generate the non-maskable interrupt request.
3.3.2.3 Interrupt channel assignments
The interrupt vector assignments are defined in the following table.
• Vector number — the value stored on the stack when an interrupt is serviced.
• IRQ number — non-core interrupt source count, which is the vector number minus
16.
The IRQ number is used within ARM's NVIC documentation.
Table 3-8. Interrupt vector assignments
Address
Vector
IRQ1
NVIC
IPR
register
number2
Source module
Source description
ARM Core System Handler Vectors
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
58
Freescale Semiconductor, Inc.
Chapter 3 Chip Configuration
Table 3-8. Interrupt vector assignments (continued)
Address
IRQ1
Vector
NVIC
IPR
register
number2
Source module
Source description
0x0000_0000
0
—
—
ARM core
Initial Stack Pointer
0x0000_0004
1
—
—
ARM core
Initial Program Counter
0x0000_0008
2
—
—
ARM core
Non-maskable Interrupt (NMI)
0x0000_000C
3
—
—
ARM core
Hard Fault
0x0000_0010
4
—
—
—
—
0x0000_0014
5
—
—
—
—
0x0000_0018
6
—
—
—
—
0x0000_001C
7
—
—
—
—
0x0000_0020
8
—
—
—
—
0x0000_0024
9
—
—
—
—
0x0000_0028
10
—
—
—
—
0x0000_002C
11
—
—
ARM core
Supervisor call (SVCall)
0x0000_0030
12
—
—
—
—
0x0000_0034
13
—
—
—
—
0x0000_0038
14
—
—
ARM core
Pendable request for system service
(PendableSrvReq)
0x0000_003C
15
—
—
ARM core
System tick timer (SysTick)
0x0000_0040
16
0
0
—
—
0x0000_0044
17
1
0
—
—
0x0000_0048
18
2
0
—
—
0x0000_004C
19
3
0
—
—
0x0000_0050
20
4
1
—
—
0x0000_0054
21
5
1
FTMRE
Command complete
0x0000_0058
22
6
1
PMC
Low-voltage warning
0x0000_005C
23
7
1
IRQ
External interrupt
2
I2C0
Single interrupt vector for all sources
Single interrupt vector for all sources
Non-Core Vectors
0x0000_0060
24
8
0x0000_0064
25
9
2
I2C1
0x0000_0068
26
10
2
SPI0
Single interrupt vector for all sources
0x0000_006C
27
11
2
SPI1
Single interrupt vector for all sources
0x0000_0070
28
12
3
UART0
Status and error
0x0000_0074
29
13
3
UART1
Status and error
0x0000_0078
30
14
3
UART2
Status and error
0x0000_007C
31
15
3
ADC0
ADC conversion complete interrupt
0x0000_0080
32
16
4
ACMP0
Analog comparator 0 interrupt
0x0000_0084
33
17
4
FTM0
Single interrupt vector for all sources
0x0000_0088
34
18
4
FTM1
Single interrupt vector for all sources
0x0000_008C
35
19
4
FTM2
Single interrupt vector for all sources
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
59
Core Modules
Table 3-8. Interrupt vector assignments (continued)
Address
IRQ1
Vector
NVIC
IPR
register
number2
Source module
Source description
0x0000_0090
36
20
5
RTC
RTC overflow
0x0000_0094
37
21
5
ACMP1
Analog comparator 1 interrupt
0x0000_0098
38
22
5
PIT_CH0
PIT CH0 overflow
0x0000_009C
39
23
5
PIT_CH1
PIT CH1 overflow
0x0000_00A0
40
24
6
KBI0(32bit)
Keyboard interrupt0(32bit)
0x0000_00A4
41
25
6
KBI1(32bit)
Keyboard interrupt1(32bit)
0x0000_00A8
42
26
6
—
0x0000_00AC
43
27
6
ICS
Clock loss of lock
0x0000_00B0
44
28
7
WDOG
Watchdog timeout
0x0000_00B4
45
29
7
PWT
Single interrupt vector for all sources
0x0000_00B8
46
30
7
MSCAN
MSCAN Rx Interrupt
0x0000_00BC
47
31
7
MSCAN
MSCAN Tx, Err and Wake-up interrupt
1. Indicates the NVIC's interrupt source number.
2. Indicates the NVIC's IPR register number used for this IRQ. The equation to calculate this value is: IRQ div 4
3.3.2.3.1
Determining the field and register location for configuring a
particular interrupt
Suppose you need to configure the SPI0 interrupt. The following table is an excerpt of the
SPI0 row from Interrupt priority levels.
Table 3-9. Interrupt vector assignments
Address
0x0000_0068
IRQ1
Vector
26
10
NVIC IPR
register
number2
2
Source module
SPI0
Source description
Single interrupt vector for all sources
1. Indicates the NVIC's interrupt source number.
2. Indicates the NVIC's IPR register number used for this IRQ. The equation to calculate this value is: IRQ div 4.
• The NVIC registers you would use to configure the interrupt are:
• NVICIPR2
• To determine the particular IRQ's field location within these particular registers:
• NVICIPR2 field starting location = 8 * (IRQ mod 4) + 6 = 22
Since the NVICIPR fields are 2-bit wide (4 priority levels), the NVICIPR2 field
range is bits 22–23.
Therefore, the field locations NVICIPR2[23:22] are used to configure the SPI0 interrupts.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
60
Freescale Semiconductor, Inc.
Chapter 3 Chip Configuration
3.3.3 Asynchronous wakeup interrupt controller (AWIC)
configuration
This section summarizes how the module has been configured in the chip. Full
documentation for this module is provided by ARM and can be found at arm.com.
Clock logic
Nested vectored
interrupt controller
(NVIC)
Wake-up
requests
Asynchronous
Wake-up Interrupt
Controller (AWIC)
Module
Module
Figure 3-10. Asynchronous wake-up interrupt controller configuration
Table 3-10. Reference links to related information
Topic
Related module
Reference
System memory map
System memory map
Clocking
Clock distribution
Power management
Power management
Interrupt control
Nested vectored
interrupt controller
(NVIC)
Wake-up requests
NVIC
AWIC wake-up sources
3.3.3.1 Wakeup sources
The device uses the following internal and external inputs to the AWIC module.
Table 3-11. AWIC stop wakeup sources
Wake-up source
Description
Available system resets
RESET pin when LPO is its clock source
Low-voltage warning
Power management controller
IRQ
IRQ pin
Pin interrupts
KBI - Any enabled pin interrupt is capable of waking the system.
ADC
The ADC is functional in Stop mode when using internal clock source.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
61
System Modules
Table 3-11. AWIC stop wakeup sources (continued)
Wake-up source
Description
ACMP
Interrupt in normal
I2C
Address match wake-up
SPI
SPI slave mode interrupt
UART
UART active edge detect at UART_RX pin
RTC
Alarm interrupt
Non-maskable interrupt
NMI pin
MSCAN
MSCAN wake-up interrupt
3.4 System Modules
3.4.1 SIM configuration
This section summarizes how the module has been configured in the chip. For a
comprehensive description of the module itself, see the module’s dedicated chapter.
Peripheral
bridge
Register
access
System integration
module (SIM)
Figure 3-11. SIM configuration
Table 3-12. Reference links to related information
Topic
Related module
Reference
Full description
SIM
SIM
System memory map
—
System memory map
Clocking
—
Clock distribution
Power management
—
Power management
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
62
Freescale Semiconductor, Inc.
Chapter 3 Chip Configuration
3.4.2 PMC configuration
This section summarizes how the module has been configured in the chip. For a
comprehensive description of the module itself, see the module’s dedicated chapter.
Peripheral
bridge
Register access
Power Management
Controller (PMC)
Figure 3-12. PMC configuration
Table 3-13. Reference links to related information
Topic
Related module
Reference
Full description
PMC
PMC
System memory map
—
System memory map
Clocking
—
Clock distribution
3.4.3 MCM configuration
ARM Cortex-M0+
core
This section summarizes how the module has been configured in the chip. For a
comprehensive description of the module itself, see the module’s dedicated chapter.
Transfers
Miscellaneous
Control Module
(MCM)
Figure 3-13. MCM configuration
Table 3-14. Reference links to related information
Topic
Related module
Reference
Full description
Miscellaneous Control
module (MCM)
MCM
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
63
System Modules
Table 3-14. Reference links to related information (continued)
Topic
Related module
Reference
System memory map
—
System memory map
Clocking
—
Clock distribution
Power management
—
Power management
Private Peripheral Bus
(PPB)
ARM Cortex-M0+ core
ARM Cortex-M0+ core
Transfer
Flash memory
controller
Flash memory controller
3.4.4 Crossbar-light switch configuration
This section summarizes how the module has been configured in the chip. For a
comprehensive description of the module itself, see the module’s dedicated chapter.
GPIO
controller
Flash
controller
M0
ARM core
unified bus
BME
S0
Crossbar Switch
S1
SRAML
SRAMU
S2
Peripheral
bridge 0
Master Modules
Peripherals
Slave Modules
Figure 3-14. Crossbar-Light switch integration
Table 3-15. Reference links to related information
Topic
Related module
Reference
System memory map
—
System memory map
Clocking
—
Clock Distribution
Crossbar switch master ARM Cortex-M0+ core
ARM Cortex-M0+ core
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
64
Freescale Semiconductor, Inc.
Chapter 3 Chip Configuration
Table 3-15. Reference links to related information (continued)
Topic
Related module
Reference
Crossbar switch slave
Flash memory
controller
Flash memory controller
Crossbar switch slave
SRAM controller
SRAM configuration
Crossbar switch slave
Peripheral bridge
Peripheral bridge
2-ported peripheral
GPIO controller
GPIO controller
3.4.4.1 Crossbar-Light switch master assignments
The masters connected to the crossbar switch are assigned as follows:
Master module
ARM core unified bus
Master port number
0
3.4.4.2 Crossbar switch slave assignments
This device contains 3 slaves connected to the crossbar switch.
The slave assignment is as follows:
Slave module
Slave port number
Flash memory controller
0
SRAM controller
1
Peripheral bridge
2
3.4.5 Peripheral bridge configuration
This section summarizes how the module has been configured in the chip. For a
comprehensive description of the module itself, see the module’s dedicated chapter.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
65
Transfers
AIPS-Lite
peripheral bridge
Transfers
Peripherals
Crossbar switch
System Security
Figure 3-15. Peripheral bridge configuration
Table 3-16. Reference links to related information
Topic
Related module
Reference
Full description
Peripheral bridge
(AIPS-Lite)
Peripheral bridge (AIPS-Lite)
System memory map
—
System memory map
Clocking
—
Clock distribution
3.4.5.1 Number of peripheral bridges
This device contains one peripheral bridge.
3.4.5.2 Memory maps
The peripheral bridges are used to access the registers of most of the modules on this
device. See AIPS-Lite Memory Map for the memory slot assignment for each module.
3.5 System Security
3.5.1 CRC configuration
This section summarizes how the module has been configured in the chip. For a
comprehensive description of the module itself, see the module’s dedicated chapter.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
66
Freescale Semiconductor, Inc.
Chapter 3 Chip Configuration
Peripheral
bridge
Register
access
CRC
Figure 3-16. CRC configuration
Table 3-17. Reference links to related information
Topic
Related module
Reference
Full description
CRC
CRC
System memory map
—
System memory map
Power management
—
Power management
3.5.2 Watchdog configuration
This section summarizes how the module has been configured in the chip.
Peripheral
bridge
System integration
module
Register
access
WDOG
Figure 3-17. Watchdog configuration
Table 3-18. Reference links to related information
Topic
Related module
Reference
Full description
Watchdog (WDOG)
Watchdog (WDOG)
Clocking
—
Clock distribution
Power management
—
Power management
Programming model
System Integration
Module (SIM)
SIM
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
67
System Security
3.5.2.1 WDOG clocks
The watchdog has four selectable clock sources:
• 1 kHz internal low power oscillator (LPOCLK)
• Internal 32 kHz reference clock (ICSIRCLK)
• External clock (OSCERCLK)
• Bus clock
3.5.2.2 WDOG operation
The WDOG module provides a fail-safe mechanism to ensure the system can be reset to a
known state of operation in case of system failure, such as the CPU clock stopping or
there being a run away condition in the software code. The watchdog counter runs
continuously off a selectable clock source and expects to be serviced (refreshed)
periodically. If it is not, it resets the system.
After any reset, the WDOG watchdog is enabled. If the WDOG watchdog is not used in
an application, it can be disabled by clearing WDOG_CS1[EN].
The refresh write sequence is a write of 0xA602 followed by a write of 0xB480 to the
WDOG_CNTH:L registers. The write of the 0xB480 must occur within 16 bus clocks
after the write of 0xA602; otherwise, the watchdog resets the MCU.
The watchdog counter has four clock source options selected by programming
WDOG_CS2[CLK]. The clock source options are the bus clock, internal 1 kHz clock,
external clock, or an internal 32 kHz clock source.
The refresh timeout time is defined by WDOG_TOVALH:L. In addition, if window
mode is used, software must not start the refresh sequence until after the time value set in
the WDOG_WINH:L registers.
An optional fixed prescaler for all clock sources allows for longer timeout periods. When
WDOG_CS2[PRES] is set, the clock source is prescaled by 256 before clocking the
watchdog counter.
The watchdog counter registers CNTH:L provide access to the value of the free-running
watchdog counter. The software can read the counter registers at any time but cannot
write directly to the watchdog counter. The refresh sequence resets the watchdog counter
to 0x0000. Write to the WDOG_CNTH:L registers of 0xC520 followed by 0xD928
within 16 bus clocks start the unlock sequence. On completing the unlock sequence, the
user must reconfigure the watchdog within 128 bus clocks; otherwise, the watchdog
forces a reset to the MCU.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
68
Freescale Semiconductor, Inc.
Chapter 3 Chip Configuration
By default, the watchdog is not functional in Debug mode, Wait mode, or Stop mode.
Setting WDOG_CS1[DBG], WDOG_CS1[WAIT] or WDOG_CS1[STOP] can activate
the watchdog in Debug, Wait or Stop modes.
3.6 Clock Modules
3.6.1 ICS configuration
This section summarizes how the module has been configured in the chip. For a
comprehensive description of the module itself, see the module’s dedicated chapter.
Peripheral
bridge
System integration
module (SIM)
System
oscillator
Register
access
ICS
Figure 3-18. ICS configuration
Table 3-19. Reference links to related information
Topic
Related module
Reference
Full description
ICS
ICS
System memory map
—
System memory map
Clocking
—
Clock distribution
Power management
—
Power management
3.6.1.1 Clock gating
This family of devices includes clock gating control for each peripheral, that is, the clock
to each peripheral can explicitly be gated on or off, using clock-gate control bits in the
SIM_SCGC register.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
69
Memories and Memory Interfaces
3.6.2 OSC configuration
This section summarizes how the module has been configured in the chip. For a
comprehensive description of the module itself, see the module’s dedicated chapter.
Peripheral
bridge
System oscillator
Module signals
Signal multiplexing
ICS
Register
access
Figure 3-19. OSC configuration
Table 3-20. Reference links to related information
Topic
Related module
Reference
Full description
OSC
OSC
System memory map
—
System memory map
Clocking
—
Clock distribution
Power management
—
Power management
Full description
ICS
ICS
3.7 Memories and Memory Interfaces
3.7.1 Flash memory configuration
This section summarizes how the module has been configured in the chip. For a
comprehensive description of the module itself, see the module’s dedicated chapter.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
70
Freescale Semiconductor, Inc.
Chapter 3 Chip Configuration
Peripheral bus
controller 0
Flash memory
controller
Register
access
Transfers
Flash memory
Figure 3-20. Flash memory configuration
Table 3-21. Reference links to related information
Topic
Related module
Reference
Full description
Flash memory
Flash memory
System memory map
—
System memory map
Clocking
—
Clock Distribution
Transfers
Flash memory
controller
Flash memory controller
Register access
Peripheral bridge
Peripheral bridge
3.7.1.1 Flash memory sizes
The amounts of flash memory for the devices covered in this document are:
Table 3-22. KE06 flash memory size
Device
Flash (KB)
Block 0 (flash) address range
MKE06Z64VLD4(R)
64
0x0000_0000 – 0x0000_FFFF
MKE06Z128VLD4(R)
128
0x0000_0000 – 0x0001_FFFF
MKE06Z64VQH4(R)
64
0x0000_0000 – 0x0000_FFFF
MKE06Z128VQH4(R)
128
0x0000_0000 – 0x0001_FFFF
MKE06Z64VLH4(R)
64
0x0000_0000 – 0x0000_FFFF
MKE06Z128VLH4(R)
128
0x0000_0000 – 0x0001_FFFF
MKE06Z64VLK4(R)
64
0x0000_0000 – 0x0000_FFFF
MKE06Z128VLK4(R)
128
0x0000_0000 – 0x0001_FFFF
3.7.1.2 Flash memory map
The flash memory and the flash registers are located at different base addresses as shown
in the figure found here.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
71
Memories and Memory Interfaces
The base address for each is specified in System memory map.
Flash memory base address
Registers
Flash base address
Flash configuration field
Flash
Figure 3-21. Flash memory map
The on-chip flash memory is implemented in a portion of the allocated Flash range to
form a contiguous block in the memory map beginning at address 0x0000_0000. See
Flash memory sizes for details of supported ranges.
Access to the flash memory ranges outside the amount of flash on the device causes the
bus cycle to be terminated with an error followed by the appropriate response in the
requesting bus master.
3.7.1.3 Flash security
For information on how flash security is implemented on this device, see Chip Security.
3.7.1.4 Erase all flash contents
In addition to software, the entire flash memory may be erased external to the flash
memory via the SW-DP debug port by setting MDM-AP CONTROL[0] (bit 0 of the
MDM-AP Control register). MDM-AP STATUS[0] (bit 0 of the MDM-AP Status
register) is set to indicate the mass erase command has been accepted. MDM-AP
CONTROL[0] is cleared when the mass erase completes.
3.7.2 Flash memory controller configuration
This section summarizes how the module has been configured in the chip. For a
comprehensive description of the module itself, see the module’s dedicated chapter.
See Platform Control Register (MCM_PLACR) register description for details on the
reset configuration of the FMC.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
72
Freescale Semiconductor, Inc.
Chapter 3 Chip Configuration
Transfers
Flash memory
controller
Transfers
Flash memory
Crossbar switch
MCM
Figure 3-22. Flash memory controller configuration
Table 3-23. Reference links to related information
Topic
Related module
Reference
Full description
Flash memory
controller
Flash memory controller
System memory map
System memory map
Clocking
Clock Distribution
Transfers
Flash memory
Flash memory
Transfers
Crossbar switch
Crossbar Switch
Register access
MCM
MCM
3.7.3 SRAM configuration
This section summarizes how the module has been configured in the chip.
Transfers
SRAM upper
crossbar
Cortex-M0+
core
switch
SRAM
controller
SRAM lower
Figure 3-23. SRAM configuration
Table 3-24. Reference links to related information
Topic
Related module
Reference
Full description
SRAM
SRAM
System memory map
—
System memory map
Clocking
—
Clock Distribution
ARM Cortex-M0+ core
—
ARM Cortex-M0+ core
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
73
Memories and Memory Interfaces
3.7.3.1 SRAM sizes
The SRAM supports single cycle access (zero wait states) at all core speeds.
The amounts of SRAM for the devices covered in this document are:
Table 3-25. SRAM size
Freescale part number
SRAM
MKE06Z64VLD4(R)
8 KB
MKE06Z128VLD4(R)
16 KB
MKE06Z64VQH4(R)
8 KB
MKE06Z128VQH4(R)
16 KB
MKE06Z64VLH4(R)
8 KB
MKE06Z128VLH4(R)
16 KB
MKE06Z64VLK4(R)
8 KB
MKE06Z128VLK4(R)
16 KB
3.7.3.2 SRAM ranges
The on-chip SRAM is split into two ranges; 1/4 is allocated to SRAM_L and 3/4 is
allocated to SRAM_U.
The on-chip RAM is implemented such that the SRAM_L and SRAM_U ranges form a
contiguous block in the memory map. As such:
• SRAM_L is anchored to 0x1FFF_FFFF and occupies the space before this ending
address.
• SRAM_U is anchored to 0x2000_0000 and occupies the space after this beginning
address.
Valid address ranges for SRAM_L and SRAM_U are then defined as:
• SRAM_L = [0x2000_0000–(SRAM_size/4)] to 0x1FFF_FFFF
• SRAM_U = 0x2000_0000 to [0x2000_0000+(SRAM_size*(3/4))-1]
This is illustrated in the following figure.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
74
Freescale Semiconductor, Inc.
SRAM size *(1/4)
Chapter 3 Chip Configuration
0x2000_0000 – SRAM_size/4
SRAM_L
SRAM size * (3/4)
0x1FFF_FFFF
0x2000_0000
SRAM_U
0x2000_0000 + SRAM_size(3/4) - 1
Figure 3-24. SRAM blocks memory map
For example, for a device containing 16 KB of SRAM, the ranges are:
• SRAM_L: 0x1FFF_F000 – 0x1FFF_FFFF
• SRAM_U: 0x2000_0000 – 0x2000_2FFF
3.7.3.3 SRAM bit operation
The on-chip SRAM is split to two range: SRAM_L and SRAM_U. The SRAM_U range
supports bit operation on this device through two ways:
• Aliased bit-band region
• Bit Manipulation Engine (BME)
A 32-bit write in the aliased region has the same effect as a read-modify-write operation
on the targeted bit in the SRAM_U region. See Aliased bit-band region for details.
The aliased bit-band region only supports simple set or clear operation. More
complicated bit operations (AND, OR, XOR, etc) could be further supported through the
BME engine. See Bit Manipulation Engine for details.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
75
Analog
3.8 Analog
3.8.1 12-bit analog-to-digital converter (ADC) configuration
This section summarizes how the module has been configured in the chip. For a
comprehensive description of the module itself, see the module’s dedicated chapter.
Peripheral
bridge
Transfers
Other peripherals
Signal multiplexing
Register
access
Module signals
SAR ADC
Figure 3-25. 12-bit SAR ADC configuration
Table 3-26. Reference links to related information
Topic
Related module
Reference
Full description
12-bit SAR ADC
12-bit SAR ADC
System memory map
—
System memory map
Clocking
—
Clock distribution
Power management
—
Power management
3.8.1.1 ADC instantiation information
This device contains one 12-bit successive approximation ADC with up to 16 channels.
Table 3-27. ADC channels
Freescale part number
ADC channels
MKE06Z64VLD4(R)
16
MKE06Z128VLD4(R)
16
MKE06Z64VQH4(R)
16
MKE06Z128VQH4(R)
16
MKE06Z64VLH4(R)
16
MKE06Z128VLH4(R)
16
MKE06Z64VLK4(R)
16
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
76
Freescale Semiconductor, Inc.
Chapter 3 Chip Configuration
Table 3-27. ADC channels (continued)
Freescale part number
ADC channels
MKE06Z128VLK4(R)
16
The ADC supports both software and hardware triggers. The ADC hardware trigger,
ADHWT, is selectable from ACMP0, ACMP1, FTM0 init trigger, FTM2 init trigger,
FTM2 match trigger, RTC overflow, or PITCH0/1 overflow. The hardware trigger can be
configured to cause a hardware trigger in MCU Run, Wait, and Stop modes.
The hardware trigger sources details are listed in the Module-to-Module section.
3.8.1.2 ADC0 connections/channel assignment
The ADC channel assignments for the device are shown in following table. Reserved
channels convert to an unknown value.
Table 3-28. ADC channel assigement
ADCH
Channel
Input
00000
AD0
PTA0/ADP0
00001
AD1
PTA1/ADP1
00010
AD2
PTA6/ADP2
00011
AD3
PTA7/ADP3
00100
AD4
PTB0/ADP4
00101
AD5
PTB1/ADP5
00110
AD6
PTB2/ADP6
00111
AD7
PTB3/ADP7
01000
AD8
PTC0/ADP8
01001
AD9
PTC1/ADP9
01010
AD10
PTC2/ADP10
01011
AD11
PTC3/ADP11
01100
AD12
PTF4/ADP12
01101
AD13
PTF5/ADP13
01110
AD14
PTF6/ADP14
01111
AD15
PTF7/ADP15
10000
AD16
Vss
10001
AD17
Vss
10010
AD18
Vss
10011
AD19
Vss
10100
AD20
Reserved
10101
AD21
Reserved
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
77
Analog
Table 3-28. ADC channel assigement (continued)
ADCH
Channel
Input
10110
AD22
Temperature Sensor
10111
AD23
Bandgap
11000
AD24
Reserved
11001
AD25
Reserved
11010
AD26
Reserved
11011
AD27
Reserved
11100
AD28
Reserved
11101
AD29
VREFH
11110
AD30
VREFL
11111
Module disabled
None
3.8.1.3 ADC analog supply and reference connections
This device includes dedicated VDDA, VSSA, VREFH and VREFL pins on 80LQFP
package. The dedicated VREFL pin is available on on 64QFP\LQFP package and
LQFP44 package, while the VREFH pin is internally connected to VDDA .
3.8.1.4 Temperature sensor and bandgap
The ADC module integrates an on-chip temperature sensor. Following actions must be
performed to use this temperature sensor.
• Configure ADC for long sample with a maximum of 1 MHz clock
• Convert the bandgap voltage reference channel (AD23)
• By converting the digital value of the bandgap voltage reference channel using
the value of VBG, the user can determine VDD.
• Convert the temperature sensor channel (AD22)
• By using the calculated value of VDD, convert the digital value of AD22 into a
voltage, VTEMP
3.8.1.5 Alternate clock
The ADC module is capable of performing conversions using the MCU bus clock, the
bus clock divided by 2, the local asynchronous clock (ADACK) within the module, or the
alternate clock, ALTCLK. The alternate clock for the devices is the external oscillator
output (OSC_OUT).
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
78
Freescale Semiconductor, Inc.
Chapter 3 Chip Configuration
The selected clock source must run at a frequency such that the ADC conversion clock
(ADCK) runs at a frequency within its specified range (fADCK) after being divided down
from the ALTCLK input as determined by ADC_SC3[ADIV].
ALTCLK is active while the MCU is in Wait mode provided the conditions described
above are met. This allows ALTCLK to be used as the conversion clock source for the
ADC while the MCU is in Wait mode.
ALTCLK cannot be used as the ADC conversion clock source while the MCU is in Stop
mode.
3.8.2 ACMP configuration
This section summarizes how the module has been configured in the chip. For a
comprehensive description of the module itself, see the module’s dedicated chapter.
Peripheral
bridge 0
Other peripherals
ACMP
Module signals
Signal multiplexing
Register
access
Figure 3-26. ACMP configuration
Table 3-29. Reference links to related information
Topic
Related module
Reference
Full description
Analog comparator
(ACMP)
Comparator
System memory map
—
System memory map
Clocking
—
Clock distribution
Power management
—
Power management
3.8.2.1 ACMP overview
The device contains two analog comparator modules (ACMP) which provide a circuit for
comparing two analog input voltages or for comparing one analog input voltage to an
internal reference voltage. The comparator circuit is used to operate across the full range
of the supply voltage (rail-to-rail operation).
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
79
Analog
The ACMP features four different inputs muxed with both positive and negative inputs to
the ACMP. One is fixed connected to built-in DAC output, the others are externally
mapped on pinouts.
The ACMP modules support internal bandgap reference voltage. When using the
bandgap reference, the user must enable the PMC bandgap buffer first.
The ACMP modules can continue to operate in Wait and Stop mode if enabled, and can
wake the MCU when a compare event occurs.
3.8.2.2 ACMP interconnections
The ACMP0 output can be configured to connect with FTM1 input capture channel 0 by
setting SIM_SOPT0[ACIC]. With ACIC field asserted, the FTM1_CH0 pin is not
available externally regardless of the configuration of the FTM1 module for channel 0.
ACMP0 and ACMP1 output are also internal connected to FTM2 trigger input and Fault
input. By configuring SIM_SOPT0[ACTRG] user can connect either ACMP0_OUT or
ACMP1_OUT to FTM2 trigger input 0. ACMP0_OUT is connected to FTM2 fault input
0 and ACMP1_OUT is connected to FTM2 fault input 3.
ACMP0 output can be directly ejected to UART0_RX by setting SIM_SOPT0[RXDCE].
In this mode, UART0_RX pinout does not work. Any external signal tagged to ACMP0
inputs can be regarded as input pins.
ACMP0 and ACMP1 output can be measured by on PWT module. By configuring
SIM_SOPT1[ACPWTS] bit, use can connect ACMP0_OUT or ACMP1_OUT to PWT
input 2.
The following table shows the input connections to the ACMP0 and ACMP1:
Table 3-30. ACMP0 input connections
ACMP0 channel
Connection
0
PTA0/ACMP0_IN0
1
PTA1/ACMP0_IN1
2
PTC4/ACMP0_IN2
3
DAC output
Table 3-31. ACMP1 input connections
ACMP1 channel
Connection
0
PTA6/ACMP1_IN0
1
PTA7/ACMP1_IN1
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
80
Freescale Semiconductor, Inc.
Chapter 3 Chip Configuration
Table 3-31. ACMP1 input connections (continued)
ACMP1 channel
Connection
2
PTB4/ACMP1_IN2
3
DAC output
3.8.2.3 ACMP in Stop mode
ACMP continues to operate in Stop mode if enabled. If ACMPx_SC[ACOPE] is enabled,
comparator output will operate as in the normal operating mode and will control
ACMPx_OUT pin. The MCU is brought out of Stop mode when a compare event occurs
and ACMPx_CS[ACIE] is enabled; ACMPx_CS[ACF] flag sets accordingly.
3.9 Timers
3.9.1 FlexTimer configuration
This section summarizes how the module has been configured in the chip. For a
comprehensive description of the module itself, see the module’s dedicated chapter.
Peripheral bus
controller 0
Transfers
Other peripherals
FlexTimer
Module signals
Signal multiplexing
Register
access
Figure 3-27. FlexTimer configuration
Table 3-32. Reference links to related information
Topic
Related module
Reference
Full description
FlexTimer
FlexTimer
System memory map
—
System memory map
Clocking
—
Clock distribution
Power management
—
Power management
Signal multiplexing
Port control
Signal multiplexing
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
81
Timers
3.9.1.1 FTM overview
The FTM timer contains up to six channels which support input capture, output compare
and the generation of PWM signals to control electric motor and power management
applications. FTM time reference is a 16-bit counter which can be used as an unsigned or
signed counter.
This device contains up to three FTM modules of one 6-channel FTM with full functions
and two 2-channel FTM with basic TPM functions. Each FTM module can use
independent external clock input. The table below summarizes the configuration of FTM
modules.
Table 3-33. FTM modules features
Feature
FTM0/FTM1
FTM2
Number of channels
2
6
Initial counting value
no
yes
Periodic TOF
no
yes
Input capture mode
yes
yes
Channel input filter
no
channels 0, 1, 2 and 3
Output compare mode
yes
yes
Edge-Aligned PWM (EPWM)
yes
yes
Center-Aligned PWM (CPWM)
yes
yes
Combine mode
no
yes
Complementary mode
no
yes
PWM synchronization
no
yes
Inverting
no
yes
Software output control (SWOC)
no
yes
Deadtime insertion
no
yes
Output mask
no
yes
Fault control
no
yes
Number of fault inputs
0
4
Fault input filter
no
fault inputs 0, 1 ,2 and 3
Polarity control
no
yes
Initialization
no
yes
Channel match trigger
no
yes
Initialization trigger
yes
yes
Capture test mode
no
yes
DMA
no
no
Dual edge capture mode
no
yes
Quadrature decoder mode
no
no
Quadrature decoder input filter
no
no
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
82
Freescale Semiconductor, Inc.
Chapter 3 Chip Configuration
Table 3-33. FTM modules features (continued)
Feature
Debug modes
Intermediary load
Global time base
enable1
Registers available
FTM0/FTM1
FTM2
no
yes
no
yes
no
yes
FTM_SC, FTM_CNT,
FTM_SC, FTM_CNT, FTM_MOD, FTM_C0SC,
FTM_MOD,
FTM_C0V, FTM_C1SC, and FTM_C1V,
FTM_C0SC, FTM_C0V, FTM_C2SC, FTM_C2V, FTM_C3SC, FTM_C3V,
FTM_C1SC, and
FTM_C4SC, FTM_C4V, FTM_C5SC, FTM_C5V,
FTM_C1V,
FTM_CNTIN, FTM_STATUS, FTM_MODE,
FTM_EXTTRIG
FTM_SYNC, FTM_OUTINIT, FTM_OUTMASK,
FTM_COMBINE, FTM_DEADTIME,
FTM_EXTTRIG, FTM_POL, FTM_FMS,
FTM_FILTER, FTM_FLTCTRL, FTM_CONF,
FTM_FLTPOL, FTM_SYNCONF,
FTM_INVCTRL, FTM_SWOCTRL, and
FTM_PWMLOAD
1. The global time base (GTB) feature allows the synchronization of multiple FTM modules on a chip. It requires the GTB
function supported by all the related FTM modules. On this device, only one FTM module (FTM2) supports the GTB
function, so the GTB function is actually not usable.
3.9.1.2 FTM clock options
The selectable FTM source clock can be the timer clock (up to 48 MHz), the fixed
frequency clock, or an external clock. The selected control source is controlled by
FTMx_SC[CLKS].
• When FTMx_SC[CLKS] = 00, no clock is selected (this in effect, disables the FTM
counter).
• When FTMx_SC[CLKS] = 01, the timer clock is selected.
• When FTMx_SC[CLKS] = 10, the fixed frequency clock(ICSFFCLK) is selected.
• When FTMx_SC[CLKS] = 11, the external clock is selected.
3.9.1.3 FTM interconnections
FTM0 has following interconnections:
• UART0_TX signal can be modulated by FTM0 channel 0 PWM output.
• UART0_RX signal can be tagged by FTM0 channel 1 input capture function by
writing 1 to SIM_SOPT0[RXDCE].
FTM1 has following interconnections:
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
83
Timers
• ACMP0 output can be internally connected to FTM1 channel 0 capture input by
writing 1 to SIM_SOPT0[ACIC].
• RTC overflow can be connected to FTM1 channel 1 capture input by writing 1 to
SIM_SOPT0[RTCC].
FTM2 supports three PWM synchronization sources:
• Trigger0 is connected to the output of ACMP0 or ACMP1 by writing 0 or 1 to
SIM_SOPT0[ACTRG].
• Trigger1 is connected to FTM0 channel 0 output.
• Trigger2 is a software trigger by writing 1 to SIM_SOPT0[FTMSYNC].
FTM2 supports four FTM fault sources:
•
•
•
•
Fault 0 is connected to ACMP0 output.
Fault1 is connected to PTA6.
Fault 2 is connected to PTA7.
Fault 3 is connected to ACMP1 output.
3.9.1.4 FTM interrupts
The FlexTimer has multiple sources of interrupt. However, either source can generate a
single interrupt request to the interrupt controller. When an FTM interrupt occurs, read
the FTM status registers to determine the exact interrupt source.
3.9.2 PIT configuration
This section summarizes how the module has been configured in the chip. For a
comprehensive description of the module itself, see the module’s dedicated chapter.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
84
Freescale Semiconductor, Inc.
Chapter 3 Chip Configuration
Peripheral
bridge
Register
access
Periodic interrupt
timer
Figure 3-28. PIT configuration
Table 3-34. Reference links to related information
Topic
Related module
Reference
Full description
PIT
PIT
System memory map
—
System memory map
Clocking
—
Clock Distribution
Power management
—
Power management
3.9.2.1 PIT overview
The PIT module is an array of timers that can be used to raise interrupts and triggers.
This device contains one PIT module with two channels and supporting chained timer
mode.
3.9.2.2 PIT interconnections
The PIT channel 0 and channel 1 trigger output can be used as ADC hardware trigger by
setting SIM_SOPT0[ADHWT].
3.9.3 RTC configuration
This section summarizes how the module has been configured in the chip. For a
comprehensive description of the module itself, see the module’s dedicated chapter.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
85
Timers
Peripheral
bridge
Module signals
Real-time clock
Signal multiplexing
Register
access
Figure 3-29. RTC configuration
Table 3-35. Reference links to related information
Topic
Related module
Reference
Full description
RTC
RTC
System memory map
—
System memory map
Clocking
—
Clock Distribution
Power management
—
Power management
3.9.3.1 RTC overview
The real-time counter (RTC) used on this device consists of one 16-bit counter, one 16bit comparator, several binary-based and decimal-based prescaler dividers, four clock
sources, and one programmable periodic interrupt. This module can be used for time-ofday, calendar or any task scheduling functions. It can also serve as a cyclic wake-up from
low-power modes without external components.
3.9.3.2 RTC interconnections
Four software selectable clock sources are available for input to prescaler with selectable
binary-based and decimal-based divider values
•
•
•
•
1 kHz internal low-power oscillator (LPOCLK)
External clock (OSCERCLK)
32 kHz internal reference clock (ICSIRCLK)
Bus clock
RTC overflow trigger can be used as hardware trigger for ADC by configuring
SIM_SOPT0[ADHWT] and may also be captured by FTM1 channel1 by configuring the
SIM_SOPT0[RTCC].
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
86
Freescale Semiconductor, Inc.
Chapter 3 Chip Configuration
3.9.4 PWT configuration
This section summarizes how the module has been configured in the chip. For a
comprehensive description of the module itself, see the module’s dedicated chapter.
Peripheral bus
controller 0
Transfers
Other peripherals
Pulse width timer
Module signals
(PWT)
Signal multiplexing
Register
access
Figure 3-30. PWT configuration
Table 3-36. Reference links to related information
Topic
Related module
Full description
PWT
Reference
PWT
System memory map
System memory map
Clocking
Clock distribution
Power management
Power management
Signal multiplexing
Port control
Signal multiplexing
3.9.4.1 PWT overview
The Pulse Width Timer (PWT) module on this device consists of one 16-bit counter,
which can be used to capture or measure the pulse width mapping on its input channels.
The counter of PWT has two selectable clocks sources, which are sharing with FTM
modules, and support up to 48 MHz with internal timer clock. PWT module supports
programmable positive or negative pulse edges, and programmable interrupt generation
upon pulse width values or counter overflow.
3.9.4.2 PWT interconnections
Two software selectable clock sources are available for input to pre-scaler divider of
PWT module:
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
87
Communication interfaces
• Timer clock : up to 48 MHz, also the option of clock source for FTM modules
• TCLK: external clock from the pads
PWT module has four input channels, which is connected as following:
Table 3-37. PWT input connections
PWT input channel
Connection
0
PTD5 or PTE2
1
PTB0 or PTH7
2
ACMP0 output or ACMP1 output
3
UART0_RX, UART1_RX or UART2_RX
3.10 Communication interfaces
3.10.1 SPI configuration
This section summarizes how the module has been configured in the chip. For a
comprehensive description of the module itself, see the module’s dedicated chapter.
Peripheral
bridge
Register
access
SPI
Module signals
Signal
multiplexing
Figure 3-31. SPI configuration
Table 3-38. Reference links to related information
Topic
Related module
Reference
Full description
SPI
SPI
System memory map
—
System memory map
Clocking
—
Clock Distribution
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
88
Freescale Semiconductor, Inc.
Chapter 3 Chip Configuration
3.10.1.1 SPI overview
This device contains two SPI modules that support 8-bit data length.
The serial peripheral interface (SPI) module provides for full-duplex, synchronous, serial
communication between the MCU and peripheral devices. These peripheral devices can
include other microcontrollers, analog-to-digital converters, shift registers, sensors,
memories, etc.
The SPI runs at a baud rate up to the bus clock divided by two in master mode and up to
the bus clock divided by 4 in slave mode. Software can poll the status flags, or SPI
operation can be interrupt-driven.
3.10.2 I2C configuration
This section summarizes how the module has been configured in the chip. For a
comprehensive description of the module itself, see the module’s dedicated chapter.
Peripheral
bridge
I2 C
Module signals
Signal multiplexing
Register
access
Figure 3-32. I2C configuration
Table 3-39. Reference links to related information
Topic
Related module
Reference
Full description
I2C
I2C
System memory map
—
System memory map
Clocking
—
Clock Distribution
Power management
—
Power management
3.10.2.1 I2C overview
This device contains two inter-integrated circuit (I2C) modules with SMBus feature. I2C
provides a method of communication between a number of devices. The interface
operates at up to 100 kb/s with maximum bus loading and timing. The device is capable
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
89
Communication interfaces
of operating at higher baud rates, up to a maximum of clock/20, with reduced bus
loading. The maximum communication length and the number of devices that can be
connected are limited by a maximum bus capacitance of 400 pF
I2C0 also provides a 4-wire interface option.
3.10.2.2 I2C0 4-wire interface feature
The 4-wire I2C0 interface has 4 uni-direction signals to improve the noise immunity of
the I2C bus instead of 2 bi-direction signals, SCL and SDA of standard I2C.
I2C0 provides 4-wire interface option. When SIM_SOPT1[I2C04WEN] bit is set, SDA/
SCL input is from SDA_IN/SCL_IN while SDA/SCL output presents on SDA_OUT/
SCL_OUT.
After the 4-wire interface feature is enabled by setting SIM_SOPT1[I2C04WEN] bit,
user can set SIM_SOPT1[I2C0OINV], and the SDA_OUT/SCL_OUT will be inverted
before output.
This feature is available only when I2C0 pin-out is not remapped.
I2C04WEN
I2C0OINV
data_w
ipp_do_sda
data_w
ipp_ind_sda
PTA1/I2C0_4WSDAOUT
PTA2/I2C0_SDA
data_r
I2C0
ipp_ind_scl
data_r
PTA3/I2C0_SCL
data_w
ipp_do_scl
data_w
PTA0/I2C0_4WSCLOUT
Figure 3-33. I2C0 4-wire interface diagram
3.10.3 UART configuration
This section summarizes how the module has been configured in the chip. For a
comprehensive description of the module itself, see the module’s dedicated chapter.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
90
Freescale Semiconductor, Inc.
Chapter 3 Chip Configuration
Peripheral
bridge
Module signals
UART
Signal multiplexing
Register
access
Figure 3-34. UART configuration
Table 3-40. Reference links to related information
Topic
Related module
Reference
Full description
UART
UART
System memory map
—
System memory map
Clocking
—
Clock Distribution
Power management
—
Power management
3.10.3.1 UART overview
This device includes three universal asynchronous receiver/transmitter (UART) modules.
Typically, these systems are used to connect to the RS232 serial input/output port of a
personal computer or workstation. They can also be used to communicate with other
embedded controllers.
A flexible, 13-bit, modulo-based baud rate generator supports a broad range of standard
baud rates beyond 115.2 kbaud. Transmit and receive within the same UART use a
common baud rate, and each UART module has a separate baud rate generator.
This UART system offers many advanced features not commonly found on other
asynchronous serial I/O peripherals on other embedded controllers. The receiver employs
an advanced data sampling technique that ensures reliable communication and noise
detection. Hardware parity, receiver wakeup, and double buffering on transmit and
receive are also included.
3.10.3.2 UART interconnection
UART0 can implement infrared functions through following tricks:
UART0_TX Modulation:
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
91
Communication interfaces
• UART0_TX output can be modulated by FTM0 channel 0 PWM output.
UART0_RX Tag:
• UART0_RX input can be tagged to FTM0 channel 1 or filtered by ACMP0 or
ACMP1. module
UART0_RX, UART1_RX and UART2_RX can be measured by PWT. By configuring
SIM_SOPT1[UARTPWTS], user can connect UART0_RX, UART1_RX or UART2_RX
to PWT_IN3.
3.10.4 MSCAN configuration
This section summarizes how the module has been configured in the chip. For a
comprehensive description of the module itself, see the module’s dedicated chapter.
Peripheral
bridge
Module signals
MSCAN
Signal multiplexing
Register
access
Figure 3-35. MSCAN configuration
Table 3-41. Reference links to related information
Topic
Related module
Reference
Full description
MSCAN
MSCAN
System memory map
—
System memory map
Clocking
—
Clock Distribution
Power management
—
Power management
3.10.4.1 MSCAN overview
This device contains a CAN module. It uses the MSCAN mudule which is a
communication controller implementing the CAN 2.0A/B protocol as defined in the
Bosch specification dated September 1991.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
92
Freescale Semiconductor, Inc.
Chapter 3 Chip Configuration
3.10.4.2 MSCAN clock source
The MSCAN module has programmable clock source. It could be clocked by bus clock
or external oscillator clock (OSCERCLK). User can configure
MSCAN_CANCTL1[CLKSRC] to select the clock used.
When OSCERCLK is selected as MSCAN clock, its frequency must not be higher than
24 MHz.
3.10.4.3 MSCAN wake-up interrupt and glitch filter
The MSCAN can be programmed to wake from Sleep or Stop mode when the CAN bus
activity is detected. The sensitivity to existing CAN bus action can be modified by
applying a low-pass filter function to the RXCAN input line by setting
MSCAN_CANCTL1[WUPM]. This feature protects the MSCAN from wake-up due to
short glitches on the CAN bus lines.
3.11 Human-machine interfaces (HMI)
3.11.1 GPIO configuration
Peripheral
bridge
Register access
Module signals
GPIO controller
Signal multiplexing
ARM Cortex -M0+
Core
Register
access
Figure 3-36. GPIO configuration
Table 3-42. Reference links to related information
Topic
Related module
Reference
Full description
GPIO
GPIO
System memory map
—
System memory map
Clocking
—
Clock Distribution
Power management
—
Power management
Crossbar switch
Crossbar switch
Crossbar switch
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
93
Human-machine interfaces (HMI)
3.11.1.1 GPIO overview
The GPIO is multi-ported and can be accessed directly by the core with zero wait states at
base address 0xF800_0000 (FGPIO). It can also be accessed by the core through the
crossbar/AIPS interface at 0x400F_F000 and at an aliased slot (15) at address
0x4000_F000. All BME operations to the GPIO space can be accomplished referencing
the aliased slot (15) at address 0x4000_F000. Only some of the BME operations can be
accomplished referencing GPIO at address 0x400F_F000.
3.11.2 KBI configuration
Peripheral
bridge
Register access
Module signals
KBI
Signal multiplexing
ARM Cortex -M0+
Core
Register
access
Figure 3-37. KBI configuration
Table 3-43. Reference links to related information
Topic
Related module
Reference
Full description
KBI
KBI
System memory map
—
System memory map
Clocking
—
Clock Distribution
Power management
—
Power management
Crossbar switch
Crossbar switch
Crossbar switch
3.11.2.1 KBI overview
This device has two 32bit keyboard interrupt modules (KBI) with up to 64 keyboard
interrupt inputs available depending on package.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
94
Freescale Semiconductor, Inc.
Chapter 3 Chip Configuration
3.11.2.2 KBI assignments
The KBI port assignments is shown by the following table.
Table 3-44. KBI port assignment
KBI
Input From
KBI0P0 ~ KBI0P7
PTA0 ~ PTA7
KBI0P8 ~ KBI0P15
PTB0 ~ PTB7
KBI0P16 ~ KBI0P23
PTC0 ~ PTC7
KBI0P24 ~ KBI0P31
PTD0 ~ PTD7
KBI1P0 ~ KBI1P7
PTE0 ~ PTE7
KBI1P8 ~ KBI1P15
PTF0 ~ PTF7
KBI1P16 ~ KBI1P23
PTG0 ~ PTG7
KBI1P24 ~ KBI1P31
PTH0 ~ PTH7
3.11.3 IRQ configuration
Peripheral
bridge
Register access
Module signals
IRQ
Signal multiplexing
ARM Cortex -M0+
Core
Register
access
Figure 3-38. IRQ configuration
Table 3-45. Reference links to related information
Topic
Related module
Reference
Full description
IRQ
IRQ
System memory map
—
System memory map
Clocking
—
Clock Distribution
Power management
—
Power management
Crossbar switch
Crossbar switch
Crossbar switch
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
95
Human-machine interfaces (HMI)
3.11.3.1 IRQ assignment
The IRQ is assigned to pin PTA5 by default . By configuring SIM_PINSEL0[IRQPS],
IRQ can be re-assigned to pin PTI0, PTI1, PTI2, PTI3, PTI4, PTI5 or PTI6.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
96
Freescale Semiconductor, Inc.
Chapter 4
Memory Map
4.1 Introduction
This device contains various memories and memory-mapped peripherals which are
located in a 4 GB memory space. This chapter describes the memory and peripheral
locations within that memory space.
4.2 System memory map
The following table shows the high-level device memory map.
Table 4-1. System memory map
System 32-bit Address Range
0x0000_0000–0x07FF_FFFF1
Destination Slave
Program flash and read-only data
Access
All masters
(Includes exception vectors in first 196 bytes)
0x0800_0000–0x0FFF_FFFF
Reserved
—
0x1000_0000– 0x1FFF_EFFF
Reserved
—
0x1FFF_F000-0x1FFF_FFFF2
SRAM_L: Lower SRAM
All masters
0x2000_0000-0x2000_2FFF
SRAM_U: Upper SRAM (bit band region)
All masters
0x2000_3000–0x21FF_FFFF
Reserved
–
0x2200_0000–0x2205_FFFF
Aliased SRAM_U bit-band region
Cortex-M0+ core
0x2206_0000–0x23FF_FFFF
Reserved
–
0x2400_0000–0x3FFF_FFFF
Bit Manipulation Engine (BME) access to SRAM_U
Cortex-M0+ core
0x4000_0000–0x4007_FFFF
AIPS Peripherals
Cortex-M0+ core
0x4008_0000–0x400F_EFFF
Reserved
–
0x400F_F000–0x400F_FFFF
General purpose input/output (GPIO)
Cortex-M0+ core
0x4010_0000–0x43FF_FFFF
Reserved
–
0x4400_0000–0x5FFF_FFFF
Bit Manipulation Engine (BME) access to AIPS Peripherals for Cortex-M0+ core
slots 0-1273
0x6000_0000–0xDFFF_FFFF
Reserved
–
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
97
Aliased bit-band region
Table 4-1. System memory map (continued)
System 32-bit Address Range
Destination Slave
Access
0xE000_0000–0xE00F_FFFF
Private Peripherals
Cortex-M0+ core
0xE010_0000–0xEFFF_FFFF
Reserved
–
0xF000_0000–0xF000_0FFF
Reserved
–
0xF000_1000–0xF000_1FFF
Reserved
–
table4
0xF000_2000–0xF000_2FFF
System ROM
Cortex-M0+ core
0xF000_3000–0xF000_3FFF
Miscellaneous Control Module (MCM)
Cortex-M0+ core
0xF000_4000–0xF7FF_FFFF
Reserved
–
0xF800_0000–0xFFFF_FFFF
IOPORT: FGPIO (single cycle)
Cortex-M0+ core
1. The program flash always begins at 0x0000_0000 but the end of implemented flash varies depending on the amount of
flash implemented for a particular device. See Flash memory sizes for details.
2. This range varies depending on SRAM sizes. See SRAM Sizes for details.
3. Includes BME operations to GPIO at slot 15 (based at 0x4000_F000).
4. This device implements a system ROM table which is used to redirect to ARM Cortex M0+ (Flycatcher) ROM table in
CoreSight debug system. See System ROM memory map for details.
4.3 Aliased bit-band region
The device supports aliased SRAM_U bit-band region with Cortex M0+ core. A 32-bit
write in the alias region has the same result as a read-modify-write operation on the
targeted bit in the bit-band region, but with only one cycle time. Aliased bit-band region
is much more efficient for bit operation.
Bit 0 of the value written to the alias region determines what value is written to the target
bit:
• Writing a value with bit 0 set writes a 1 to the target bit.
• Writing a value with bit 0 clear writes a 0 to the target bit.
A 32-bit read in the alias region returns either:
• a value of 0x0000_0000 to indicate the target bit is clear
• a value of 0x0000_0001 to indicate the target bit is set
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
98
Freescale Semiconductor, Inc.
Chapter 4 Memory Map
Bit-band region
31
Alias bit-band region
31
0
32 KByte
1 KByte
0
Figure 4-1. Alias bit-band mapping
4.4 Bit Manipulation Engine
The Bit Manipulation Engine (BME) provides hardware support for atomic read-modifywrite memory operations to the peripheral and SRAM_U address space. By combining
the basic load and store instruction support in the Cortex-M instruction set architecture
with the concept of decorated storage provided by the BME, the resulting implementation
provides a robust and efficient read-modify-write capability to this class of ultra low-end
microcontrollers. See Bit Manipulation Engine (BME) for a detailed description of its
functionality.
4.5 System ROM memory map
The system ROM table is optionally required by ARM CoreSight debug infrastructure to
discover the components on the chip.
For core configurations like that supported by Cortex-M0+, ARM recommends that a
debugger identifies and connects to the debug components using the CoreSight debug
infrastructure.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
99
System ROM memory map
ARM recommends that a debugger follows the flow as shown in the following figure to
discover the components in the CoreSight debug infrastructure. In this case, a debugger
reads the peripheral and component ID registers for each CoreSight component in the
CoreSight system.
CoreSight access port
Base pointer
Redirection from the
+ System ROM table, if implemented
+
Flycatcher ROM table
CoreSight ID
Pointers
System control space
+ Data watchpoint unit
+
+ Breakpoint unit
+
CoreSight ID
CoreSight ID
CoreSight ID
Flycatcher CPUID
Watchpoint control
Breakpoint control
Debug control
+ Optional component
+
Figure 4-2. CoreSight discovery process
Following table shows the Freescale system ROM table memory map. It includes the
ROM entry, peripheral ID and component ID required by ARM CoreSight debug
infrastructure.
NOTE
This device contains only standard ARM M0+ core debug
components which defined in Flycatcher ROM table. No
custom-built debug components are included.
ROM memory map
Absolute
address
(hex)
Register name
Width
Access
(in bits)
Reset value
Section/
page
F000_2000
Entry (ROM_ENTRY0)
32
R
See section
4.5.1/101
F000_2004
End of Table Marker Register (ROM_TABLEMARK)
32
R
0000_0000h
4.5.2/102
F000_2FCC System Access Register (ROM_SYSACCESS)
32
R
0000_0001h
4.5.3/102
F000_2FD0 Peripheral ID Register (ROM_PERIPHID4)
32
R
See section
4.5.4/103
F000_2FD4 Peripheral ID Register (ROM_PERIPHID5)
32
R
See section
4.5.4/103
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
100
Freescale Semiconductor, Inc.
Chapter 4 Memory Map
ROM memory map (continued)
Absolute
address
(hex)
Width
Access
(in bits)
Register name
Reset value
Section/
page
F000_2FD8 Peripheral ID Register (ROM_PERIPHID6)
32
R
See section
4.5.4/103
F000_2FDC Peripheral ID Register (ROM_PERIPHID7)
32
R
See section
4.5.4/103
F000_2FE0 Peripheral ID Register (ROM_PERIPHID0)
32
R
See section
4.5.4/103
F000_2FE4 Peripheral ID Register (ROM_PERIPHID1)
32
R
See section
4.5.4/103
F000_2FE8 Peripheral ID Register (ROM_PERIPHID2)
32
R
See section
4.5.4/103
F000_2FEC Peripheral ID Register (ROM_PERIPHID3)
32
R
See section
4.5.4/103
F000_2FF0
Component ID Register (ROM_COMPID0)
32
R
See section
4.5.5/103
F000_2FF4
Component ID Register (ROM_COMPID1)
32
R
See section
4.5.5/103
F000_2FF8
Component ID Register (ROM_COMPID2)
32
R
See section
4.5.5/103
F000_2FFC Component ID Register (ROM_COMPID3)
32
R
See section
4.5.5/103
4.5.1 Entry (ROM_ENTRYn)
The System ROM Table begins with "n" relative 32-bit addresses, one for each debug
component present in the device and terminating with an all-zero value signaling the end
of the table at the "n+1"-th value.
It is hardwired to specific values used during the auto-discovery process by an external
debug agent.
Address: F000_2000h base + 0h offset + (4d × i), where i=0d to 0d
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
ENTRY
R
W
Reset
x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x*
* Notes:
• x = Undefined at reset.
ROM_ENTRYn field descriptions
Field
ENTRY
Description
ENTRY
Entry 0 (CM0+ ROM Table) is hardwired to 0xF00F_D003.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
101
System ROM memory map
4.5.2 End of Table Marker Register (ROM_TABLEMARK)
This register indicates end of table marker. It is hardwired to specific values used during
the auto-discovery process by an external debug agent.
Address: F000_2000h base + 4h offset = F000_2004h
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
MARK
R
W
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
ROM_TABLEMARK field descriptions
Field
Description
MARK
Hardwired to 0x0000_0000
4.5.3 System Access Register (ROM_SYSACCESS)
This register indicates system access. It is hardwired to specific values used during the
auto-discovery process by an external debug agent.
Address: F000_2000h base + FCCh offset = F000_2FCCh
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
SYSACCESS
R
W
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
ROM_SYSACCESS field descriptions
Field
SYSACCESS
Description
Hardwired to 0x0000_0001
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
102
Freescale Semiconductor, Inc.
Chapter 4 Memory Map
4.5.4 Peripheral ID Register (ROM_PERIPHIDn)
These registers indicate the peripheral IDs. They are hardwired to specific values used
during the auto-discovery process by an external debug agent.
Address: F000_2000h base + FD0h offset + (4d × i), where i=0d to 7d
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
PERIPHID
R
W
Reset
x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x*
* Notes:
• x = Undefined at reset.
ROM_PERIPHIDn field descriptions
Field
Description
PERIPHID
Peripheral ID1 is hardwired to 0x0000_00E0; ID2 to 0x0000_0008; and all the others to 0x0000_0000.
4.5.5 Component ID Register (ROM_COMPIDn)
These registers indicate the component IDs. They are hardwired to specific values used
during the auto-discovery process by an external debug agent.
Address: F000_2000h base + FF0h offset + (4d × i), where i=0d to 3d
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
COMPID
R
W
Reset
x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x*
* Notes:
• x = Undefined at reset.
ROM_COMPIDn field descriptions
Field
COMPID
Description
Component ID
Component ID0 is hardwired to 0x0000_000D; ID1 to 0x0000_0010; ID2 to 0x0000_0005; ID3 to
0x0000_00B1.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
103
Peripheral bridge (AIPS-Lite) memory map
4.6 Peripheral bridge (AIPS-Lite) memory map
The Peripheral Bridge memory map is accessible via one slave port on the crossbar in the
0x4000_0000–0x400F_FFFF region. The device implements one peripheral bridge that
defines a 1024 KB address space.
The three regions associated with this space are:
• A 128 KB region, partitioned as 32 spaces, each 4 KB in size and reserved for onplatform peripheral devices. The AIPS controller generates unique module enables
for all 32 spaces.
• A 384 KB region, partitioned as 96 spaces, each 4 KB in size and reserved for offplatform modules. The AIPS controller generates unique module enables for all 96
spaces.
• The last slot is a 4 KB region beginning at 0x400F_F000 for accessing the GPIO
module. The GPIO slot (slot 128) is an alias of slot 15. This block is also directly
interfaced to the core and provides direct access without incurring wait states
associated with accesses via the AIPS controller.
Modules that are disabled via their clock gate control bits in the SIM registers disable the
associated AIPS slots. Access to any address within an unimplemented or disabled
peripheral bridge slot results in a transfer error termination.
For programming model accesses via the peripheral bridges, there is generally only a
small range within the 4 KB slots that is implemented. Accessing an address that is not
implemented in the peripheral results in a transfer error termination.
4.6.1 Read-after-write sequence and required serialization of
memory operations
In some situations, a write to a peripheral must be completed fully before a subsequent
action can occur. Examples of such situations include:
• Exiting an interrupt service routine (ISR)
• Changing a mode
• Configuring a function
In these situations, the application software must perform a read-after-write sequence to
guarantee the required serialization of the memory operations:
1. Write the peripheral register.
2. Read the written peripheral register to verify the write.
3. Continue with subsequent operations.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
104
Freescale Semiconductor, Inc.
Chapter 4 Memory Map
4.6.2 Peripheral Bridge (AIPS-Lite) Memory Map
NOTE
• Slots 0-95 and 128 are 32-bit data width modules, with the
exception that slots 49,82 are 8-bit data width modules
(IRQ, WDOG), and slot 36 is 16-bit data width
module(MSCAN).
• Slots 96-127 are 8-bit data width modules. While slot 121
and 122 are 32-bit data width modules(KBI0, KBI1)
Table 4-21. Peripheral bridge 0 slot assignments
System 32-bit base address
Slot
number
Module
0x4000_0000
0
—
0x4000_1000
1
—
0x4000_2000
2
—
0x4000_3000
3
—
0x4000_4000
4
—
0x4000_5000
5
—
0x4000_6000
6
—
0x4000_7000
7
—
0x4000_8000
8
—
0x4000_9000
9
—
0x4000_A000
10
—
0x4000_B000
11
—
0x4000_C000
12
—
0x4000_D000
13
—
0x4000_E000
14
—
0x4000_F000
15
GPIO controller (aliased to 0x400F_F000)
0x4001_0000
16
—
0x4001_1000
17
—
0x4001_2000
18
—
0x4001_3000
19
—
0x4001_4000
20
—
0x4001_5000
21
—
0x4001_6000
22
—
0x4001_7000
23
—
0x4001_8000
24
—
0x4001_9000
25
—
0x4001_A000
26
—
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
105
Peripheral bridge (AIPS-Lite) memory map
Table 4-21. Peripheral bridge 0 slot assignments (continued)
System 32-bit base address
Slot
number
Module
0x4001_B000
27
—
0x4001_C000
28
—
0x4001_D000
29
—
0x4001_E000
30
—
0x4001_F000
31
—
0x4002_0000
32
Flash memory (FTMRE)
0x4002_1000
33
—
0x4002_2000
34
—
0x4002_3000
35
—
0x4002_4000
36
MSCAN
0x4002_5000
37
—
0x4002_6000
38
—
0x4002_7000
39
—
0x4002_8000
40
0x4002_9000
41
—
0x4002_A000
42
—
0x4002_B000
43
—
0x4002_C000
44
—
0x4002_D000
45
—
0x4002_E000
46
—
0x4002_F000
47
—
0x4003_0000
48
—
0x4003_1000
49
IRQ controller (IRQ)
0x4003_2000
50
Cyclic Redundancy Check (CRC)
0x4003_3000
51
Pulse width timer (PWT)
0x4003_4000
52
—
0x4003_5000
53
—
0x4003_6000
54
—
0x4003_7000
55
Periodic interrupt timers (PIT)
0x4003_8000
56
Flex timer 0 (FTM0)
0x4003_9000
57
Flex timer 1 (FTM1)
0x4003_A000
58
Flex timer 2 (FTM2)
0x4003_B000
59
Analog-to-digital converter (ADC)
0x4003_C000
60
—
0x4003_D000
61
Real time clock (RTC)
0x4003_E000
62
—
0x4003_F000
63
—
0x4004_0000
64
—
0x4004_1000
65
—
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
106
Freescale Semiconductor, Inc.
Chapter 4 Memory Map
Table 4-21. Peripheral bridge 0 slot assignments (continued)
System 32-bit base address
Slot
number
Module
0x4004_2000
66
—
0x4004_3000
67
—
0x4004_4000
68
—
0x4004_5000
69
—
0x4004_6000
70
—
0x4004_7000
71
—
0x4004_8000
72
System integration module (SIM)
0x4004_9000
73
Port controller
0x4004_A000
74
—
0x4004_B000
75
—
0x4004_C000
76
—
0x4004_D000
77
—
0x4004_E000
78
—
0x4004_F000
79
—
0x4005_0000
80
—
0x4005_1000
81
—
0x4005_2000
82
Watchdog (WDOG)
0x4005_3000
83
—
0x4005_4000
84
—
0x4005_5000
85
—
0x4005_6000
86
—
0x4005_7000
87
—
0x4005_8000
88
—
0x4005_9000
89
—
0x4005_A000
90
—
0x4005_B000
91
—
0x4005_C000
92
—
0x4005_D000
93
—
0x4005_E000
94
—
0x4005_F000
95
—
0x4006_0000
96
—
0x4006_1000
97
—
0x4006_2000
98
—
0x4006_3000
99
—
0x4006_4000
100
Internal clock source (ICS)
0x4006_5000
101
System oscillator (OSC)
0x4006_6000
102
I2C0
0x4006_7000
103
I2C1
0x4006_8000
104
—
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
107
Private Peripheral Bus (PPB) memory map
Table 4-21. Peripheral bridge 0 slot assignments (continued)
System 32-bit base address
Slot
number
Module
0x4006_9000
105
—
0x4006_A000
106
Universal asynchronous receiver/transmitter 0 (UART0)
0x4006_B000
107
Universal asynchronous receiver/transmitter 1 (UART1)
0x4006_C000
108
Universal asynchronous receiver/transmitter 2 (UART2)
0x4006_D000
109
—
0x4006_E000
110
—
0x4006_F000
111
—
0x4007_0000
112
—
0x4007_1000
113
—
0x4007_2000
114
—
0x4007_3000
115
Analog comparator 0 (ACMP0)
0x4007_4000
116
Analog comparator 1 (ACMP1)
0x4007_5000
117
—
0x4007_6000
118
Serial peripheral interface 0 (SPI0)
0x4007_7000
119
Serial peripheral interface 1 (SPI1)
0x4007_8000
120
—
0x4007_9000
121
Keyboard interrupt 0 (KBI0)
0x4007_A000
122
Keyboard interrupt 1 (KBI1)
0x4007_B000
123
—
0x4007_C000
124
—
0x4007_D000
125
Power management controller (PMC)
0x4007_E000
126
—
0x4007_F000
127
—
0x400F_F000
128
GPIO controller
4.7 Private Peripheral Bus (PPB) memory map
The PPB is part of the defined ARM bus architecture and provides access to select
processor-local modules. These resources are only accessible from the core; other system
masters do not have access to them.
Table 4-22. PPB memory map
System 32-bit Address Range
Resource
0xE000_0000–0xE000_DFFF
Reserved
0xE000_E000–0xE000_EFFF
System Control Space
(SCS)
Additional Range Detail
Resource
0xE000_E000–0xE000_E00F
Reserved
0xE000_E010–0xE000_E0FF
SysTick
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
108
Freescale Semiconductor, Inc.
Chapter 4 Memory Map
Table 4-22. PPB memory map (continued)
System 32-bit Address Range
Resource
0xE000_F000–0xE00F_EFFF
Reserved
0xE00F_F000–0xE00F_FFFF
Core ROM Space (CRS)
Additional Range Detail
Resource
0xE000_E100–0xE000_ECFF
NVIC
0xE000_ED00–0xE000_ED8F
System Control Block
0xE000_ED90–0xE000_EDEF
Reserved
0xE000_EDF0–0xE000_EEFF
Debug
0xE000_EF00–0xE000_EFFF
Reserved
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
109
Private Peripheral Bus (PPB) memory map
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
110
Freescale Semiconductor, Inc.
Chapter 5
Clock Distribution
5.1 Introduction
This chapter presents the clock architecture for the device, the overview of the clocks and
includes a terminology section.
The Cortex M0+ resides within a synchronous core platform, where the processor and
bus masters, flash and peripherals clocks can be configured independently.
The ICS module will be used for main system clock generation. The ICS module controls
which clock sources (internal references, external crystals or external clock signals)
generate the source of the system clocks.
5.2 Programming model
The selection and multiplexing of system clock sources is controlled and programmed via
the ICS module. The setting of clock dividers and module clock gating for the system are
programmed via the SIM module. See those sections for detailed register and bit
descriptions.
5.3 High-level device clocking diagram
This device contains following on-chip clock sources:
• Internal Clock Source (ICS) module: The main clock source generator providing bus
clock and other reference clocks to peripherals
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
111
High-level device clocking diagram
• System Oscillator (OSC) module: The system oscillator providing reference clock to
internal clock source (ICS), the real-time clock counter clock module (RTC), and
other MCU sub-systems
• Low-Power Oscillator (LPO) module: The on-chip low-power oscillator providing 1
kHz reference clock to RTC and Watchdog (WDOG)
Figure 5-1 shows how clocks from the ICS and OSC modules are distributed to the
microcontroller’s other function units. Some modules in the microcontroller have
selectable clock input.
The following registers of the system oscillator, ICS, and SIM modules control the
multiplexers, dividers, and clock gates shown in the figure:
Table 5-1. Registers controlling multiplexers, dividers, and clock gate
OSC
ICS
SIM
Multiplexers
OSC_CR
ICS_C1
SIM_SOPT
Dividers
—
ICS_C2
SIM_CLKDIV
Clock gates
OSC_CR
ICS_C1
SIM_SCGC
SIM
ICS
CG
ICSIRCLK
CG
RTC / WDOG
CG
FTM
DIV3
CG
FTM / PWT
DIV1
CG
Core/System Clock
CG
Bus/Flash Clock
CG
RTC/WDOG/ADC/MSCAN
ICSFFCLK
37.5 kHz IRC
FLL
IREFS
BDIV
ICSFLLCLK
ICSOUTCLK
CLKS
DIV2
RDIV
CLK_GEN
System oscillator
EXTAL
XTAL
OSCCLK
OSC
logic
OSCERCLK
XTAL_CLK
OSCOS
PMC
1kHz LPO
LPOCLK
RTC / WDOG
CG — Clock gate
Note: See subsequent sections for details on where these clocks are used.
Figure 5-1. Clocking diagram
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
112
Freescale Semiconductor, Inc.
Chapter 5 Clock Distribution
5.4 Clock definitions
The following table describes the clocks in Figure 5-1.
Table 5-2. Clock definitions
Clock name
Description
Core clock
ICSOUTCLK divided by DIV1, clocks the ARM Cortex-M0+ core. It's the CPU HCLK
Platform clock
ICSOUTCLK divided by DIV1, clocks the crossbar switch and NVIC, It's the free-running
FCLK
System clock
ICSOUTCLK divided by DIV1, clocks the bus masters directly
Bus clock
System clock divided by DIV2, clocks the bus slaves and peripherals
Flash clock
System clock divided by DIV2, clocks the Flash memory module. It is same as Bus clock in
this device
Timer clock
ICSOUTCLK divided by DIV3, clocks the FTM and PWT modules
Debug clock
Debug logic clock. On this device it is derived from platform clock
SWD clock
DAP interface clock. SWD clock is typically driven by an external debugger and completely
asynchronous to Core clock and platform clock
ICSIRCLK
ICS output of the internal 32 kHz IRC reference clock. ICSIRCLK can be selected as the
clock source of RTC or WDOG modules
ICSOUTCLK
ICS output of either IRC, ICSFLLCLK or ICS's external reference clock that sources the core,
system, bus, and flash clock
ICSFLLCLK
Output of the FLL, FLL locks the frequency to 1280 times the internal or external reference
frequency
ICSFFCLK
ICS output of the fixed frequency clock. ICSFFCLK can be selected as clock source for the
FTM modules. The frequency of the ICSFFCLK is determined by the setting of the ICS
OSCCLK
System oscillator output of the internal oscillator or sourced directly from EXTAL. Used as
ICS external reference clock
OSCERCLK
System oscillator output sourced from OSCCLK that can be selected as the clock source of
MSCAN1, RTC, WDOG or ADC modules
LPOCLK
PMC 1 kHz output, The LPOCLK can be selected as the clock source to the RTC or WDOG
modules
1. When OSCERCLK used as MSCAN clock, its frequency should not be higher than 24 MHz
5.4.1 Device clock summary
The following table provides more information regarding the on-chip clocks.
Table 5-3. Clock summary
Clock name
Core clock
Run mode frequency
Clock source
Clock is disabled when…
Up to 48 MHz
ICSOUTCLK clock
divider
In Wait and Stop modes
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
113
Clock definitions
Table 5-3. Clock summary (continued)
Clock name
Run mode frequency
Clock source
Clock is disabled when…
Platform clock
Up to 48 MHz
ICSOUTCLK clock
divider
In Stop mode
System clock
Up to 48 MHz
ICSOUTCLK clock
divider
In Stop mode
Timer clock
Up to 48 MHz
ICSOUTCLK clock
divider
In Stop mode
Bus clock
Up to 24 MHz
ICSOUTCLK clock
divider
In Stop mode
Debug clock
Up to 24 MHz
Derive from Platform
clock
Debug not enabled
SWD clock
Up to 24MHz
SWD_CLK pin
Input from external clock, so will not be
disabled.
Flash clock
Up to 24 MHz
ICSOUTCLK clock
divider
In Stop mode
31.25–39.0625 kHz IRC
IRC
ICS_C1[IRCLKEN]=0,
Internal reference
(ICSIRCLK)
or
In Stop mode and ICS_C1[IREFSTEN]=0
External reference
(OSCERCLK)
DC up to 48 MHz (bypass),
System OSC
OSC_CR[OSCEN]=0,
31.25–39.0625 kHz
or
or
In Stop mode and OSC_CR[OSCSTEN]=0
4–24 MHz (crystal)
FLL out clock
40-50 MHz
(ICSFLLCLK)
System OSC
In Stop mode,
or IRC
or
FLL not enabled
ICS Fixed Frequency 31.25–39.0625 kHz
clock (ICSFFCLK)
LPOCLK
1 kHz
System OSC
In Stop mode
or IRC
PMC
Available in all power modes
5.4.2 Clock distribution
The following figure shows a simplified clock distribution diagram
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
114
Freescale Semiconductor, Inc.
Chapter 5 Clock Distribution
LPOCLK
1-kHz
LPO
EXTAL
XTAL
OSCCLK
OSC
ICSIRCLK
TCLK0
TCLK1
TCLK2
ICSFFCLK
FTM0
FTM1
FTM2
PWT
MsCAN
WDG
RTC
ADC
PIT
CRC
I2C0
I2C1
SPI0
SPI1
UART0
UART1
UART2
ACMP0
CPU
NVIC
AWIC
DEBUG
DAP
RAM
FLASH
FMC
RGPIO
AIPS
TIMER_CLK
BUS_CLK
32-kHz
IRC
FLL
CORE_CLK
ICSOUTCLK
CLK_GEN
PLAT_CLK
SYS_CLK
FLASH_CLK
ICS
Figure 5-2. High-level clock distribution diagram
NOTE
Clock divide and gating are not shown in clock distribution
diagram.
5.5 Internal clocking sources
The internal clock sources on this device are as following:
• On-chip RC oscillator range of 31.25–39.0625 kHz as the reference of FLL input.
• On-chip internal 1 kHz oscillator as the low-frequency low-power source for RTC
and WDOG according to specific use case requirement.
The following table shows the frequency availability of this device:
Table 5-4. ICS bus frequency availability with internal reference
Reference
FEI (high range)
ICSOUTCLK
BDIV = 0
40 MHz ~ 50 MHz1
BDIV = 1
20 MHz ~ 25 MHz
BDIV = 2
10 MHz ~ 12.5 MHz
BDIV = 4
5 MHz ~ 6.25 MHz
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
115
External clock sources
Table 5-4. ICS bus frequency availability with internal reference (continued)
Reference
ICSOUTCLK
BDIV = 8
2.5 MHz ~ 3.125 MHz
BDIV = 16
1.25 MHz ~ 1.5625 MHz
BDIV = 32
625 kHz ~ 781.25 kHz
BDIV = 64
312.5 kHz ~ 390.625 kHz
BDIV = 128
156.25 kHz ~ 195.3125 kHz
1. Carefully configure SIM_CLKDIV and BDIV to avoid any clock frequency higher than 48 MHz.
5.6 External clock sources
This device supports the following two external clock sources:
• External square wave input clock up to DC-48 MHz.
• External crystal oscillator or resonator:
• Low-range: 31.25–39.0625 kHz
• High-range: 4–24 MHz
NOTE
The external square wave input clock is only used when the
OSC module is working under external clock mode (bypass).
With the external square wave clock source, the user can use
FBE mode with FLL disabled to achieve lower power
consumption or precise clock source.
The following table shows the frequency availability of this device when sourcing from
OSC clock. OSC external clock mode is not shown.
Table 5-5. OSC frequency availability
ICS configuration
External reference
RDIV
FBE
31.25 kHz ~ 39.0625 kHz
̶
4 MHz ~ 24 MHz
̶
31.25 kHz ~ 39.0625 kHz
RDIV = 1
62.5 kHz ~ 78.125 kHz
RDIV = 2
125 kHz ~ 56.25 kHz
RDIV = 4
250 kHz ~ 312.5 kHz
RDIV = 8
500 kHz ~ 625 kHz
RDIV = 16
1 MHz ~ 1.25 MHz
RDIV = 32
2 MHz ~ 2.5 MHz
RDIV = 64
4 MHz ~ 5 MHz
RDIV = 128
FEE1
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
116
Freescale Semiconductor, Inc.
Chapter 5 Clock Distribution
Table 5-5. OSC frequency availability (continued)
ICS configuration
External reference
RDIV
8 MHz ~ 10 MHz
RDIV = 256
16 MHz ~ 20 MHz
RDIV = 512
1. In FEE mode, FLL output frequency = OSC/RDIV *1280. Select the OSC and RDIV carefully to keep the FLL output
frequency within the limits.
5.7 Clock gating
The clock to each module can be individually gated on and off using the System Clock
Gating Control Register (SIM_SCGC). Prior to initializing a module, set the
corresponding bit in System Clock Gating Control Register (SIM_SCGC) to enable the
clock. Before turning off the clock, make sure to disable the module.
Any bus access to a peripheral that has its clock disabled generates an error termination.
5.8 Module clocks
The following table summarizes the clocks associated with each module.
Table 5-6. Module clocks
Module
Bus interface clock
Internal clocks
I/O interface clocks
Core modules
ARM Cortex-M0+ core
Platform clock
Core clock
—
NVIC
Platform clock
—
—
DAP
Platform clock
—
SWD_CLK
System modules
Port control
Bus clock
—
—
Crossbar Switch
Platform clock
—
—
Peripheral bridges
System clock
Bus clock
—
PMC, SIM
Bus clock
LPOCLK
—
MCM
Platform clock
—
—
CRC
Bus clock
—
—
Watchdog timer
Bus clock
Bus clock
—
LPOCLK
ICSIRCLK
OSCERCLK
Clocks
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
117
Module clocks
Table 5-6. Module clocks (continued)
Module
Bus interface clock
Internal clocks
I/O interface clocks
ICS
Bus clock
ICSOUTCLK
—
ICSFLLCLK
ICSIRCLK
OSCERCLK
OSC
Bus clock
OSCERCLK
—
Memory and memory interfaces
Flash Controller
System clock
—
—
Flash memory
Flash clock
—
—
SRAM
Platform clock
—
—
Bus clock
—
Analog
ADC
Bus clock
OSCERCLK
ADACK
ACMP0
Bus clock
—
—
ACMP1
Bus clock
—
—
PIT
Bus clock
—
—
PWT
Timer clock
—
TCLK0/1/2
FTM0
Timer clock
Timer clock
TCLK0/1/2
Timers
ICSFFCLK
FTM1
Timer clock
Timer clock
TCLK0/1/2
ICSFFCLK
FTM2
Timer clock
Timer clock
TCLK0/1/2
ICSFFCLK
RTC
Bus clock
Bus clock
RTC_CLKOUT
LPOCLK
ICSIRCLK
OSCERCLK
Communication interfaces
SPI0
Bus clock
—
SPI0_SCK
SPI1
Bus clock
—
SPI1_SCK
I2C0
Bus clock
—
I2C0_SCL
I2C1
Bus clock
—
I2C1_SCL
UART0/SCI0
Bus clock
—
—
UART1/SCI1
Bus clock
—
—
UART2/SCI2
Bus clock
—
—
MSCAN
Bus clock
OSCERCLK1
—
Human-machine interfaces
GPIO
System clock
—
—
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
118
Freescale Semiconductor, Inc.
Chapter 5 Clock Distribution
Table 5-6. Module clocks (continued)
Module
Bus interface clock
Internal clocks
I/O interface clocks
KBI0
Bus clock
—
—
KBI1
Bus clock
—
—
1. When OSCERCLK is used as MSCAN clock, its frequency should not be higher than 24 MHz
5.8.1 FTM and PWT clocking
The counters for the FTM and PWT modules have a selectable clock as shown in the
following figure. TCLK0 TCLK1 and TCLK2 are optional external clock inputs for the
timers.
NOTE
If TCLK0, TCLK1 or TCLK2 are selected as the counter clock
for FTMs or PWT, the on-chip timer clock (TIMER_CLK) is
still required to synchronize the counter results. And the onchip timer clock (TIMER_CLK) must be at least 4x faster than
the external clock from TCLK0, TCLK1 or TCLK2.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
119
Module clocks
ICSIRCLK
ICSFLLCLK
DIV3
TIMER_CLK
OSCERCLK
FTM0 clock
ICSFFCLK
TCLK0
TCLK1
TCLK2
FTM0_SC[CLKS]
SIM_PINSEL0[FTM0CLKPS]
FTM1 clock
SIM_PINSEL0[FTM1CLKPS]
FTM1_SC[CLKS]
FTM2 clock
SIM_PINSEL0[FTM2CLKPS]
FTM2_SC[CLKS]
PWT clock
SIM_PINSEL0[PWTCLKPS]
PWT_R1[PCLKS]
Figure 5-3. FTM and PWT clock generation
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
120
Freescale Semiconductor, Inc.
Chapter 6
Reset and Boot
6.1 Introduction
The following reset sources are supported in this MCU:
Table 6-1. Reset sources
Reset sources
POR reset
Description
• Power-on reset (POR)
System resets
•
•
•
•
•
•
•
•
External pin reset (PIN)
Low-voltage detect (LVD)
Watchdog (WDOG) timer
ICS loss of clock (LOC) reset
Stop mode acknowledge error (SACKERR)
Software reset (SW)
Lockup reset (LOCKUP)
MDM DAP system reset
Each of the system reset sources has an associated bit in the System Reset Status and ID
Register (SIM_SRSID).
The MCU can exit and reset in functional mode where the CPU is executing code
(default) or the CPU is in a debug halted state. There are several boot options that can be
configured. See Boot for more details.
6.2 Reset
This section discusses basic reset mechanisms and sources. Some modules that cause
resets can be configured to cause interrupts instead. Consult the individual peripheral
chapters for more information.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
121
Reset
6.2.1 Power-on reset (POR)
When power is initially applied to the MCU or when the supply voltage drops below the
power-on reset voltage level (VPOR), the POR circuit causes a POR reset condition.
As the supply voltage rises, the LVD circuit holds the MCU in reset until the supply has
risen above the LVD low threshold (VLVDL). POR and LVD fields of the System Reset
Status and ID Register (SIM_SRSID). (SIM_SRSID[POR] and SIM_SRSID[LVD]) are
set following a POR.
6.2.2 System reset sources
Resetting the MCU provides a way to start processing from a known set of initial
conditions. System reset begins with the on-chip regulator in full regulation and system
clocking generation from an internal reference. When the processor exits reset, it
performs the following:
• Reads the start SP (SP_main) from vector-table offset 0
• Reads the start program counter (PC) from vector-table offset 4
• The Link Register (LR) is set to 0xFFFF_FFFF.
The on-chip peripheral modules are disabled and the non-analog I/O pins are initially
configured as disabled (except that the SWD_DIO/SWD_CLK, NMI and RESET pins
could be enabled after system reset according to the System Options Register 0
(SIM_SOPT0) setting). The pins with analog functions assigned to them default to their
analog function after reset.
6.2.2.1 External pin reset (RESET)
This pin has an internal pullup resistor. Asserting RESET wakes the device from any
mode.
After POR reset, the PTA5 pin functions as RESET. SIM_SOPT0[RSTPE] must be
programmed to enable the other functions. When this field is clear, this pin can function
as PTA5 or other alternative functions.
6.2.2.1.1
Reset pin filter
The RESET/IRQ pin filter supports filtering from both the 1 kHz LPO clock and the bus
clock. It can be used as a simple low-pass filter to filter any glitch that is introduced from
the pin of RESET/IRQ.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
122
Freescale Semiconductor, Inc.
Chapter 6 Reset and Boot
The glitch width threshold can be adjusted easily by setting Port Filter Register 0
(PORT_IOFLT0) between 1~4096 BUSCLKs (or 1~128 LPOCLKs). This configurable
glitch filter can replace an on-board external analog filter, and greatly improve the EMC
performance. Setting Port Filter Register 0 (PORT_IOFLT0) can configure the filter of
the whole port.
6.2.2.2 Low-voltage detect (LVD)
This device includes a system to protect against low-voltage conditions in order to protect
memory contents and control MCU system states during supply voltage variations. This
system consists of a power-on reset (POR) circuit, and an LVD circuit with a user
selectable trip voltage, either high (VLVDH) or low (VLVDL).
The LVD circuit is enabled when PMC_SPMSC1[LVDE] is set and the trip voltage is
selected by PMC_SPMSC2[LVDV]. The LVD is disabled upon entering the stop modes
unless PMC_SPMSC1[LVDSE] is set or in Serial Wire Debug (SWD) mode. If
PMC_SPMSC1[LVDSE] and PMC_SPMSC1[LVDE] are both set, the current
consumption will be higher in Stop mode with the LVD enabled.
6.2.2.3 Watchdog timer
The watchdog timer (WDOG) monitors the operation of the system by expecting periodic
communication from the software. This communication is generally known as servicing
(or refreshing) the watchdog. If this periodic refreshing does not occur, the watchdog
issues a system reset. The WDOG reset causes SIM_SRSID[WDOG] to set.
6.2.2.4 ICS loss-of-clock (LOC)
The ICS on this chip supports external reference clock monitor with reset capability.
In FBE, or FEE modes, if 1 is written to ICS_C4[CME], the clock monitor is enabled. If
the external reference falls below a certain frequency, such as floc_high or floc_low
depending on OSC_CR[RANGE], the MCU will reset. SIM_SRSID[LOC] will be set to
indicate the error.
In FBILP mode, the FLL is not on, so the external reference clock monitor will not
function even if 1 is written to ICS_C4[CME].
External reference clock monitor uses FLL as the internal reference clock. The FLL must
be functional before ICS_C4[CME] is set.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
123
Reset
6.2.2.5 Stop mode acknowledge error (SACKERR)
This reset is generated if the core attempts to enter Stop mode, but not all modules
acknowledge Stop mode within 1025 cycles of the 1 kHz LPO clock.
A module might not acknowledge the entry to Stop mode if an error condition occurs.
The error can be caused by a failure of an external clock input to a module.
6.2.2.6 Software reset (SW)
The SYSRESETREQ field in the NVIC application interrupt and reset control register
can be set to force a software reset on the device. (See ARM's NVIC documentation for
the full description of the register fields, especially the VECTKEY field requirements.)
Setting SYSRESETREQ generates a software reset request. This reset forces a system
reset of all major components except for the debug module.
6.2.2.7 Lockup reset (LOCKUP)
The LOCKUP gives immediate indication of seriously errant kernel software. This is the
result of the core being locked because of an unrecoverable exception following the
activation of the processor’s built in system state protection hardware.
The LOCKUP condition causes a system reset and also causes SIM_SRSID[LOCKUP]
to set.
6.2.2.8 MDM-AP system reset request
Set the System Reset Request field in the MDM-AP Control register to initiate a system
reset. This is the primary method for resets via the SWD interface. The system reset is
held until this bit is cleared.
Set the Core Hold Reset field in the MDM-AP Control register to hold the core in reset as
the rest of the chip comes out of system reset.
6.2.3 MCU resets
A variety of resets are generated by the MCU to reset different modules.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
124
Freescale Semiconductor, Inc.
Chapter 6 Reset and Boot
6.2.3.1 POR Only
The POR Only reset asserts on the POR reset source only. It resets the PMC and RTC.
The POR Only reset also causes all other reset types to occur.
6.2.3.2 Chip POR
The Chip POR asserts on POR and LVD reset sources. It resets the Reset Pin Filter
registers and parts of the SIM and ICS.
The Chip POR also causes the Chip Reset (including Early Chip Reset) to occur.
6.2.3.3 Early Chip Reset
The Early Chip Reset asserts on all reset sources. It resets only the flash memory module
and ARM platform. It negates before flash memory initialization begins ("earlier" than
when the Chip Reset negates).
6.2.3.4 Chip Reset
Chip Reset asserts on all reset sources and only negates after the RESET pin has also
negated. It resets the remaining modules (the modules not reset by other reset types).
6.3 Boot
This section describes the boot sequence, including sources and options.
Some configuration information such as clock trim values stored in factory programmed
flash locations is auto-loaded.
6.3.1 Boot sources
The CM0+ core adds support for a programmable Vector Table Offset Register (VTOR1 )
to relocate the exception vector table. This device supports booting from internal flash
and RAM.
1.
VTOR: refer to Vector Table Offset Register in the ARMv6-M Architecture Reference Manual.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
125
Boot
This device supports booting from internal flash with the reset vectors located at
addresses 0x0 (initial SP_main), 0x4 (initial PC), and RAM with relocating the exception
vector table to RAM.
6.3.2 Boot sequence
At power-up, the on-chip regulator holds the system in a POR state until the input supply
is above the POR threshold. The system continues to be held in this static state until the
internally regulated supplies have reached a safe operating voltage as determined by the
LVD. The Reset Controller logic then controls a sequence to exit reset.
1. A system reset is held on internal logic, the RESET pin is driven out low (about 4.2
µs), and the ICS is enabled in its default clocking mode.
2. The RESET pin is released. If RESET pin continues to be asserted (an indication of a
slow rise time on the RESET pin or external drive in low), the system continues to be
held in reset. Once the RESET pin is detected high, the core clock is enabled and the
system is released from reset.
3. The NVM starts internal initialization. Flash Controller is released from reset and
begins initialization operations while the core is still halted before the flash
initialization completes.
4. When the flash Initialization completes(16 µs) , the core sets up the stack, program
counter (PC), and link register (LR). The processor reads the start SP (SP_main)
from vector-table offset 0. The core reads the start PC from vector-table offset 4. LR
is set to 0xFFFF_FFFF. The CPU begins execution at the PC location.
Subsequent system resets follow this same reset flow.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
126
Freescale Semiconductor, Inc.
Chapter 7
Power Management
7.1 Introduction
This chapter describes the various chip power modes and functionality of the individual
modules in these modes.
7.2 Power modes
The power management controller (PMC) provides the user with multiple power options.
The different modes of operation are supported to allow the user to optimize power
consumption for the level of functionality needed.
The device supports Run, Wait, and Stop modes which are easy to use for customers both
from different power consumption level and functional requirement. I/O states are held in
all the modes.
• Run mode—CPU clocks can be run at full speed and the internal supply is fully
regulated.
• Wait mode—CPU shuts down to conserve power; system clocks and bus clock are
running and full regulation is maintained.
• Stop mode—LVD optional enabled, and voltage regulator is in standby.
The three modes of operation are Run, Wait, and Stop. The WFI instruction invokes both
Wait and Stop modes for the chip.
Table 7-1. Chip power modes
Power mode
Normal RUN
Description
Allows maximum performance of chip. Default mode out of
reset; on-chip voltage regulator is on.
Core mode
Normal recover
method
Run
—
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
127
Entering and exiting power modes
Table 7-1. Chip power modes (continued)
Power mode
Description
Core mode
Normal recover
method
Normal Wait via
WFI
Allows peripherals to function while the core is in Sleep mode,
reducing power. NVIC remains sensitive to interrupts;
peripherals continue to be clocked.
Sleep
Interrupt
Normal Stop via
WFI
Places chip in static state. Lowest power mode that retains all
registers while optionally maintaining LVD protection. NVIC is
disabled; AWIC is used to wake up from interrupt; peripheral
clocks are stopped.
Sleep Deep
Interrupt
7.3 Entering and exiting power modes
The WFI instruction invokes Wait and Stop modes for the chip. The processor exits the
low-power mode via an interrupt.
NOTE
The WFE instruction can have the side effect of entering a lowpower mode, but that is not its intended usage. See ARM
documentation for more on the WFE instruction.
7.4 Module operation in low-power modes
The following table illustrates the functionality of each module while the chip is in each
of the low-power modes. The standard behavior is shown with some exceptions.
Table 7-2. Module operation in low-power modes
Modules
Run
Wait
Stop
Core modules
CPU
On
Standby
Standby
NVIC
On
On
Standby
Full regulation
Full regulation
Loose regulation
WDOG
On
On
Optional on
LVD
On
On
Optional on
CRC
On
On
Standby
System modules
PMC
Clock
ICS
On
On
Optional on
OSC
On
On
Optional on
LPO
On
On
Always on
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
128
Freescale Semiconductor, Inc.
Chapter 7 Power Management
Table 7-2. Module operation in low-power modes (continued)
Modules
Run
Wait
Stop
On
On
Standby
On
Standby1
Standby
Memory
Flash
RAM
Timer
FTM
On
On
Standby
PIT
On
On
Standby
PWT
On
On
Standby
RTC
On
On
Optional on
Analog
ADC
On
On
Optional on
ACMP
On
On
Optional on
Communication interfaces
UART
On
On
Standby2
SPI
On
On
Standby3
IIC
On
On
Standby4
MSCAN
On
On
Standby2
Human-machine interfaces
KBI
On
On
Standby5
IRQ
On
On
Standby5
I/O
On
On
State held
1. SRAM enable signal disables internal clock signal and masks the address and data inputs when held low, RAM clock at
chip can be active in Wait mode.
2. Supports wake-up on edge in Stop mode
3. Supports slave mode receive and wake-up in Stop mode
4. Supports address match wake-up in Stop mode
5. Supports pin interrupt wake-up in Stop mode
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
129
Module operation in low-power modes
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
130
Freescale Semiconductor, Inc.
Chapter 8
Security
8.1 Introduction
This device implements security based on the mode selected from the flash module. The
following sections provide an overview of flash security and details of the effects of
security on non-flash modules.
8.2 Flash security
The flash module provides security information to the MCU based on the state held by
the FTMRE_FSEC[SEC ]. The MCU, in turn, confirms the security request and limits
access to flash resources. During reset, the flash module initializes the Flash Security
Register (FTMRE_FSEC) using data read from the security byte of the flash
configuration field.
NOTE
The security features apply only to external accesses: CPU
accesses to the flash are not affected by the status of Flash
Security Register (FTMRE_FSEC).
In the unsecured state all flash commands are available on the programming interfaces
either from the debug port (SWD) or user code execution. When the flash is secured
(FTMRE_FSEC[SEC ] = 00, 01, or 11), the programmer interfaces are only allowed to
launch mass erase operations. Additionally, in this mode, the debug port has no access to
memory locations.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
131
Security interactions with other modules
8.3 Security interactions with other modules
The flash security settings are used by the system to determine what resources are
available. The following sections describe the interactions between modules and the flash
security settings or the impact that the flash security has on non-flash modules.
8.3.1 Security interactions with debug
When flash security is active, the SWD port cannot access the memory resources of the
MCU.
Although most debug functions are disabled, the debugger can write to the Flash Mass
Erase in Progress field of the MDM-AP Control Register to trigger a mass erase (Erase
All Blocks) command. A mass erase via the debugger is allowed even when some
memory locations are protected.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
132
Freescale Semiconductor, Inc.
Chapter 9
Debug
9.1 Introduction
This device's debug is based on the ARM CoreSight architecture and is configured to
provide the maximum flexibility as allowed by the restrictions of the pinout and other
available resources.
It provides register and memory accessibility from the external debugger interface, basic
run/halt control plus 2 breakpoints and 2 watchpoints.
This device supports only one debug interface, Serial Wire Debug (SWD).
9.2 Debug port pin descriptions
The debug port pins default to their SWD functionality after power-on-reset (POR).
Table 9-1. Serial wire debug pin description
Pin Name
Type
SWD_CLK
Input
SWD_DIO
Input / Output
Description
Serial Wire Clock. This pin is the clock for debug logic when in the Serial
Wire Debug mode. 1
Serial Wire Debug Data input/output. The SWD_DIO pin is used by an
external debug tool for communication and device control. This pin is
pulled up internally.
1. The pad library of this device does not support on-chip pull down; the SWD_CLK pin supports only pullup controlled by
PTAPE0, external pulldown resistor is required to fully support SWD protocol.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
133
SWD status and control registers
9.3 SWD status and control registers
Through the ARM Debug Access Port (DAP), the debugger has access to the status and
control elements, implemented as registers on the DAP bus as shown in Figure 9-1. These
registers provide additional control and status for low-power mode recovery and typical
run-control scenarios. The status register bits also provide a means for the debugger to
get updated status of the core without having to initiate a bus transaction across the
crossbar switch, thus remaining less intrusive during a debug session.
A miscellaneous debug module (MDM) is implemented on this device, which contains
the DAP control and status registers. It is important to note that these DAP control and
status registers are not memory-mapped within the system memory map and are only
accessible via the Debug Access Port using SWD. The MDM-AP is accessible as Debug
Access Port 1 with the available registers shown in the table below.
Table 9-2. MDM-AP register summary
Address
Register
Description
0x0100_0000
Status
See MDM-AP status register
0x0100_0004
Control
See MDM-AP Control register
0x0100_00FC
IDR
Read-only identification register that
always reads as 0x001C_0020
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
134
Freescale Semiconductor, Inc.
Chapter 9 Debug
DPACC
APACC
Data[31:0]
A[3:2]
RnW
Debug Port
0x0C
See the ARM Debug Interface v5p1 Supplement.
RnW
Bus Matrix
IDR
Status
MDM -AP
Control
AHB Access Port
(AHB -AP)
Internal Bus
A[3:2]
SELECT[31:24] (APSEL) selects the AP
SELECT[7:4] (APBANKSEL) selects the bank
A[3:2] from the APACC selects the register
within the bank
AHB-AP
SELECT[31:24] = 0x00 selects the AHB-AP
See ARM documentation for further details
Access Port
A[7:4]
0x00
Data[31:0]
0x3F
APSEL
Decode
SW-DP
Generic
Debug Port
(DP)
0x01
0x08
RnW
Read Buffer (RDBUFF)
AP Select (SELECT)
0x04
A[3:2]
Control/Status (CTRL/STAT)
Debug Port ID Register (IDCODE) 0x00
DP Registers
Data[31:0]
MDM-AP
SELECT[31:24] = 0x01 selects the MDM-AP
SELECT[7:4] = 0x0 selects the bank with Status and Ctrl
A[3:2] = 2’b00 selects the Status Register
A[3:2] = 2’b01 selects the Control Register
SELECT[7:4] = 0xF selects the bank with IDR
A[3:2] = 2’b11 selects the IDR Register
(IDR register reads 0x001C_0020)
See Control and Status Register Descriptions
Figure 9-1. MDM AP addressing
9.3.1 MDM-AP status register
Table 9-3. MDM-AP status register assignments
Bit
Name
Description
0
Flash Mass Erase Acknowledge
The Flash Mass Erase Acknowledge field is cleared after POR reset. The
field is also cleared at launch of a mass erase command due to write of
Flash Mass Erase in Progress field in MDM AP Control Register. The
Flash Mass Erase Acknowledge is set after Flash control logic has started
the mass erase operation.
1
Flash Ready
Indicates that flash memory has been initialized and debugger can be
configured even if system is continuing to be held in reset via the
debugger.
0 Flash is under initialization.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
135
SWD status and control registers
Table 9-3. MDM-AP status register assignments (continued)
Bit
Name
Description
1 Flash is ready.
2
System Security
Indicates the security state. When secure, the debugger does not have
access to the system bus or any memory mapped peripherals. This field
indicates when the part is locked and no system bus access is possible.
NOTE: This bit is not valid until Flash Ready bit set.
0 Device is unsecured.
1 Device is secured.
3
System Reset
Indicates the system reset state.
0 System is in reset.
1 System is not in reset.
4
Reserved
5 – 15
16
Reserved for future use
Always read 0.
Core Halted
Indicates the core has entered Debug Halt mode
0 Core is not halted.
1 Core is halted.
17
Core SLEEPDEEP
SLEEPDEEP=1 indicates the core has entered Stop mode.
18
Core SLEEPING
SLEEPING=1 indicates the core has entered Wait mode.
Reserved for future use
Always reads 0.
19 – 31
9.3.2 MDM-AP Control register
Table 9-4. MDM-AP Control register assignments
Bit
Name
Secure1
Description
0
Flash Mass Erase in Progress
Y
Set to cause mass erase. Cleared by hardware after mass erase
operation completes.
1
Debug Disable
N
Set to disable debug. Clear to allow debug operation. When set, it
overrides the C_DEBUGEN field within the DHCSR2 and forces to
disable Debug logic.
2
Debug Request
N
Set to force the core to halt.
If the core is in Stop or Wait mode, this field can be used to wake the
core and transition to a halted state.
3
System Reset Request
Y
Set to force a system reset. The system remains held in reset until
this field is cleared. When this bit is set, RESET pin does not reflect
the status of system reset and does not keep low.
4
Core Hold
N
Configuration field to control core operation at the end of system
reset sequencing.
0 Normal operation—release the core from reset along with the rest
of the system at the end of system reset sequencing.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
136
Freescale Semiconductor, Inc.
Chapter 9 Debug
Table 9-4. MDM-AP Control register assignments (continued)
Bit
Name
Secure1
Description
1 Suspend operation—hold the core in reset at the end of reset
sequencing. Once the system enters this suspended state, clearing
this control bit immediately releases the core from reset and CPU
operation begins.
5– 31
Reserved for future use
N
1. Command available in secure mode
2. DHCSR: refer to the Debug Halting Control and Status Register in the ARMv6-M Architecture Reference Mannual.
9.4 Debug resets
The debug system receives the following sources of reset:
• System POR reset
Conversely, the debug system is capable of generating system reset using the following
mechanism:
• A system reset in the DAP control register which allows the debugger to hold the
system in reset.
• Writing 1 to the SYSRESETREQ field in the NVIC Application Interrupt and Reset
Control register
• A system reset in the DAP control register which allows the debugger to hold the
core in reset.
9.5 Debug in low-power modes
In low-power modes in which the debug modules are kept static or powered off, the
debugger cannot gather any debug data for the duration of the low-power mode.
• If the debugger is held static, the debug port returns to full functionality as soon as
the low-power mode exits and the system returns to a state with active debug.
• If the debugger logic is powered off, the debugger is reset on recovery and must be
reconfigured once the low-power mode is exited.
The active debug will prevent the chip from entering low-power mode. In case the chip is
already in low-power mode, a debug request from MDM-AP control register will wake
the chip from low-power mode.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
137
Debug and security
9.6 Debug and security
When flash security is enabled, the debug port capabilities are limited in order to prevent
exploitation of secure data. In the secure state, the debugger still has access to the status
register and can determine the current security state of the device. In the case of a secure
device, the debugger has the capability of performing only a mass erase operation.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
138
Freescale Semiconductor, Inc.
Chapter 10
Signal Multiplexing and Signal Descriptions
10.1 Introduction
To optimize functionality in small packages, pins have several functions available via
signal multiplexing. This chapter illustrates which of this device's signals are multiplexed
on which external pin.
The Pin Selection Register 0 (SIM_PINSEL0)and Pin Selection Register 1
(SIM_PINSEL1)control which signal is present on the external pin. Refer to that register
to find the detailed control operation of a specific multiplexed pin.
10.2 Pinout
10.2.1 Signal multiplexing and pin assignments
The following table shows the signals available on each pin and the locations of these
pins on the devices supported by this document. The Port Control Module is responsible
for selecting which ALT functionality is available on each pin.
NOTE
VSS and VSSA are internally connected.
VREFH and VDDA are internally connected in 64-pin
packages.
PTB4, PTB5, PTD0, PTD1, PTE0, PTE1, PTH0, and PTH1 are
high-current drive pins when operated as output.
PTA2 and PTA3 are true open-drain pins when operated as
output.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
139
Pinout
80
64
44
LQFP LQFP LQFP
/QFP
Pin Name
Default
ALT0
ALT1
ALT2
ALT3
ALT4
ALT5
ALT6
1
1
1
PTD1
DISABLED
PTD1
KBI0_P25
FTM2_CH3
SPI1_MOSI
2
2
2
PTD0
DISABLED
PTD0
KBI0_P24
FTM2_CH2
SPI1_SCK
3
3
—
PTH7
DISABLED
PTH7
KBI1_P31
PWT_IN1
4
4
—
PTH6
DISABLED
PTH6
KBI1_P30
5
—
—
PTH5
DISABLED
PTH5
KBI1_P29
6
5
3
PTE7
DISABLED
PTE7
KBI1_P7
TCLK2
FTM1_CH1
CAN0_TX
7
6
4
PTH2
DISABLED
PTH2
KBI1_P26
BUSOUT
FTM1_CH0
CAN0_RX
8
7
5
VDD
VDD
9
8
6
VDDA
VDDA
10
—
—
VREFH
VREFH
VREFH
11
9
7
VREFL
VREFL
VREFL
12
10
8
VSS/
VSSA
VSS/
VSSA
13
11
9
PTB7
EXTAL
PTB7
KBI0_P15
I2C0_SCL
EXTAL
14
12
10
PTB6
XTAL
PTB6
KBI0_P14
I2C0_SDA
XTAL
15
13
11
PTI4
DISABLED
PTI4
IRQ
16
—
—
PTI1
DISABLED
PTI1
IRQ
UART2_TX
17
—
—
PTI0
DISABLED
PTI0
IRQ
UART2_RX
18
14
—
PTH1
DISABLED
PTH1
KBI1_P25
FTM2_CH1
19
15
—
PTH0
DISABLED
PTH0
KBI1_P24
FTM2_CH0
20
16
—
PTE6
DISABLED
PTE6
KBI1_P6
21
17
—
PTE5
DISABLED
PTE5
KBI1_P5
22
18
12
PTB5
DISABLED
PTB5
KBI0_P13
FTM2_CH5
SPI0_PCS
ACMP1_OUT
23
19
13
PTB4
NMI_b
PTB4
KBI0_P12
FTM2_CH4
SPI0_MISO
ACMP1_IN2
24
20
14
PTC3
ADC0_SE11
PTC3
KBI0_P19
FTM2_CH3
ADC0_SE11
25
21
15
PTC2
ADC0_SE10
PTC2
KBI0_P18
FTM2_CH2
ADC0_SE10
26
22
16
PTD7
DISABLED
PTD7
KBI0_P31
UART2_TX
27
23
17
PTD6
DISABLED
PTD6
KBI0_P30
UART2_RX
28
24
18
PTD5
DISABLED
PTD5
KBI0_P29
PWT_IN0
29
—
—
PTI6
DISABLED
PTI6
IRQ
30
—
—
PTI5
DISABLED
PTI5
IRQ
31
25
19
PTC1
ADC0_SE9
PTC1
KBI0_P17
FTM2_CH1
ADC0_SE9
32
26
20
PTC0
ADC0_SE8
PTC0
KBI0_P16
FTM2_CH0
ADC0_SE8
33
—
—
PTH4
DISABLED
PTH4
KBI1_P28
I2C1_SCL
34
—
—
PTH3
DISABLED
PTH3
KBI1_P27
I2C1_SDA
35
27
—
PTF7
ADC0_SE15
PTF7
KBI1_P15
ADC0_SE15
36
28
—
PTF6
ADC0_SE14
PTF6
KBI1_P14
ADC0_SE14
37
29
—
PTF5
ADC0_SE13
PTF5
KBI1_P13
ADC0_SE13
38
30
—
PTF4
ADC0_SE12
PTF4
KBI1_P12
ADC0_SE12
39
31
21
PTB3
ADC0_SE7
PTB3
KBI0_P11
SPI0_MOSI
FTM0_CH1
ADC0_SE7
40
32
22
PTB2
ADC0_SE6
PTB2
KBI0_P10
SPI0_SCK
FTM0_CH0
ADC0_SE6
ALT7
VDD
VREFH
VSSA
VDDA
VSS
NMI_b
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
140
Freescale Semiconductor, Inc.
Chapter 10 Signal Multiplexing and Signal Descriptions
80
64
44
LQFP LQFP LQFP
/QFP
Pin Name
Default
ALT0
ALT1
ALT2
ALT3
ALT4
ALT5
ALT6
41
33
23
PTB1
ADC0_SE5
PTB1
KBI0_P9
UART0_TX
42
34
24
PTB0
ADC0_SE4
PTB0
KBI0_P8
UART0_RX
43
35
—
PTF3
DISABLED
PTF3
KBI1_P11
UART1_TX
44
36
—
PTF2
DISABLED
PTF2
KBI1_P10
UART1_RX
45
37
25
PTA7
ADC0_SE3
PTA7
KBI0_P7
46
38
26
PTA6
ADC0_SE2
PTA6
KBI0_P6
47
39
—
PTE4
DISABLED
PTE4
KBI1_P4
48
40
27
VSS
VSS
VSS
49
41
28
VDD
VDD
VDD
50
—
—
PTG7
DISABLED
PTG7
KBI1_P23
FTM2_CH5
SPI1_PCS
51
—
—
PTG6
DISABLED
PTG6
KBI1_P22
FTM2_CH4
SPI1_MISO
52
—
—
PTG5
DISABLED
PTG5
KBI1_P21
FTM2_CH3
SPI1_MOSI
53
—
—
PTG4
DISABLED
PTG4
KBI1_P20
FTM2_CH2
SPI1_SCK
54
42
—
PTF1
DISABLED
PTF1
KBI1_P9
FTM2_CH1
55
43
—
PTF0
DISABLED
PTF0
KBI1_P8
FTM2_CH0
56
44
29
PTD4
DISABLED
PTD4
KBI0_P28
57
45
30
PTD3
DISABLED
PTD3
KBI0_P27
SPI1_PCS
58
46
31
PTD2
DISABLED
PTD2
KBI0_P26
SPI1_MISO
59
47
32
PTA3
DISABLED
PTA3
KBI0_P3
UART0_TX
I2C0_SCL
60
48
33
PTA2
DISABLED
PTA2
KBI0_P2
UART0_RX
I2C0_SDA
61
49
34
PTA1
ADC0_SE1
PTA1
KBI0_P1
FTM0_CH1
I2C0_
4WSDAOUT
ACMP0_IN1
ADC0_SE1
62
50
35
PTA0
ADC0_SE0
PTA0
KBI0_P0
FTM0_CH0
I2C0_
4WSCLOUT
ACMP0_IN0
ADC0_SE0
63
51
36
PTC7
DISABLED
PTC7
KBI0_P23
UART1_TX
CAN0_TX
64
52
37
PTC6
DISABLED
PTC6
KBI0_P22
UART1_RX
CAN0_RX
65
—
—
PTI3
DISABLED
PTI3
IRQ
66
—
—
PTI2
DISABLED
PTI2
IRQ
67
53
—
PTE3
DISABLED
PTE3
KBI1_P3
SPI0_PCS
68
54
38
PTE2
DISABLED
PTE2
KBI1_P2
SPI0_MISO
69
—
—
VSS
VSS
VSS
70
—
—
VDD
VDD
VDD
71
55
—
PTG3
DISABLED
PTG3
KBI1_P19
72
56
—
PTG2
DISABLED
PTG2
KBI1_P18
73
57
—
PTG1
DISABLED
PTG1
KBI1_P17
74
58
—
PTG0
DISABLED
PTG0
KBI1_P16
75
59
39
PTE1
DISABLED
PTE1
KBI1_P1
SPI0_MOSI
76
60
40
PTE0
DISABLED
PTE0
KBI1_P0
SPI0_SCK
77
61
41
PTC5
DISABLED
PTC5
KBI0_P21
78
62
42
PTC4
SWD_CLK
PTC4
KBI0_P20
RTC_CLKOUT
FTM1_CH0
ACMP0_IN2
79
63
43
PTA5
RESET_b
PTA5
KBI0_P5
IRQ
TCLK0
RESET_b
ALT7
ADC0_SE5
PWT_IN1
ADC0_SE4
FTM2_FLT2
ACMP1_IN1
ADC0_SE3
FTM2_FLT1
ACMP1_IN0
ADC0_SE2
PWT_IN0
I2C1_SCL
TCLK1
I2C1_SDA
FTM1_CH1
RTC_CLKOUT
SWD_CLK
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
141
Pinout
80
64
44
LQFP LQFP LQFP
/QFP
80
64
44
Pin Name
PTA4
Default
ALT0
SWD_DIO
ALT1
PTA4
ALT2
ALT3
KBI0_P4
ALT4
ACMP0_OUT
ALT5
ALT6
ALT7
SWD_DIO
PTA4
PTA5
PTC4
PTC5
PTE0
PTE1
PTG0
PTG1
PTG2
PTG3
VDD
VSS
PTE2
PTE3
PTI2
PTI3
PTC6
PTC7
PTA0
PTA1
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
10.2.2 Device pin assignment
VREFL
11
50
PTG7
VSS/VSSA
12
49
VDD
PTB7
13
48
VSS
PTB6
14
47
PTE4
PTI4
15
46
PTA6
PTI1
16
45
PTA7
PTI0
17
44
PTF2
PTH1
18
43
PTF3
PTH0
19
42
PTB0
PTE6
20
41
PTB1
40
PTG6
PTB2
51
39
10
PTB3
VREFH
38
PTG5
PTF4
52
37
9
PTF5
VDDA
36
PTG4
PTF6
53
35
8
PTF7
VDD
34
PTF1
PTH3
54
33
7
PTH4
PTH2
PTC0
PTF0
32
55
31
6
PTC1
PTE7
30
PTD4
PTI5
56
29
5
PTI6
PTH5
28
PTD3
PTD5
57
27
4
PTD6
PTH6
26
PTD2
PTD7
58
25
3
PTC2
PTH7
24
PTA3
PTC3
59
23
2
PTB4
PTD0
22
PTA2
PTB5
60
21
1
PTE5
PTD1
Figure 10-1. 80-pin LQFP package
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
142
Freescale Semiconductor, Inc.
PTA4
PTA5
PTC4
PTC5
PTE0
PTE1
PTG0
PTG1
PTG2
PTG3
PTE2
PTE3
PTC6
PTC7
PTA0
PTA1
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
Chapter 10 Signal Multiplexing and Signal Descriptions
VDD
VREFL
9
40
VSS
VSS/VSSA
10
39
PTE4
PTB7
11
38
PTA6
PTB6
12
37
PTA7
PTI4
13
36
PTF2
PTH1
14
35
PTF3
PTH0
15
34
PTB0
PTE6
16
33
PTB1
PTE5
32
41
PTB2
8
31
VDDA/VREFH
PTB3
PTF1
30
42
PTF4
7
29
VDD
PTF5
PTF0
28
43
PTF6
6
27
PTH2
PTF7
PTD4
26
44
PTC0
5
25
PTE7
PTC1
PTD3
24
45
PTD5
4
23
PTH6
PTD6
PTD2
22
46
PTD7
3
21
PTH7
PTC2
PTA3
20
47
PTC3
2
19
PTD0
PTB4
PTA2
18
48
PTB5
1
17
PTD1
Figure 10-2. 64-pin QFP/LQFP packages
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
143
PTA4
PTA5
PTC4
PTC5
PTE0
PTE1
PTE2
PTC6
PTC7
PTA0
PTA1
44
43
42
41
40
39
38
37
36
35
34
Module signal description tables
28
VDD
VREFL
7
27
VSS
VSS/VSSA
8
26
PTA6
PTB7
9
25
PTA7
PTB6
10
23
PTB1
PTI4
11
24
PTB0
22
6
PTB2
VDDA/VREFH
21
PTD4
PTB3
29
20
5
PTC0
VDD
19
PTD3
PTC1
30
18
4
PTD5
PTH2
17
PTD2
PTD6
31
16
3
PTD7
PTE7
15
PTA3
PTC2
32
14
2
PTC3
PTD0
13
PTA2
PTB4
33
12
1
PTB5
PTD1
Figure 10-3. 44-pin LQFP package
10.3 Module signal description tables
The following sections correlate the chip-level signal name with the signal name used in
the module's chapter. They also briefly describe the signal function and direction.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
144
Freescale Semiconductor, Inc.
Chapter 10 Signal Multiplexing and Signal Descriptions
10.3.1 Core modules
Table 10-1. SWD signal descriptions
Chip signal name
Module signal
name
Description
I/O
SWD_DIO
SWD_DIO
Serial Wire Debug Data input/output. The SWD_DIO pin is used by
an external debug tool for communication and device control. This
pin is pulled up internally.
Input /
Output
SWD_CLK
SWD_CLK
Serial Wire Clock. This pin is the clock for debug logic when in the
Serial Wire Debug mode. 1
Input
1. The pad library of this device does not support on-chip pull down; the SWD_CLK pin supports only pullup controlled by
PTAPE0, external pulldown resistor is required to fully support SWD protocol.
10.3.2 System modules
Table 10-2. System signal descriptions
Chip signal name
Module signal
name
NMI
—
Description
Non-maskable interrupt
I/O
I
NOTE: Driving the NMI signal low forces a non-maskable
interrupt, if the NMI function is selected on the
corresponding pin.
RESET
—
Reset bidirectional signal
I/O
VDD
—
MCU power
I
VSS
—
MCU ground
I
10.3.3 Clock modules
Table 10-3. OSC signal descriptions
Chip signal name
Module signal
name
EXTAL
EXTAL
XTAL
XTAL
Description
I/O
External clock/oscillator input
Analog
input
Oscillator output
Analog
output
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
145
Module signal description tables
10.3.4 Analog
Table 10-4. ADC0 signal descriptions
Chip signal name
Module signal
name
ADC0_SEn
AD15-AD0
VDD/VREFH
VSS/VREFL
Description
I/O
Analog channel inputs
I
VDDA/VREFH
Analog power supply / voltage reference high
I
VSSA/VREFL
Analog power ground / voltage reference low
I
Table 10-5. ACMP0 signal descriptions
Chip signal name
Module signal
name
Description
I/O
ACMP0_INn
ACMP0_IN[2:0]
Analog voltage inputs
I
ACMP0_OUT
ACMP0_OUT
Comparator output
O
Table 10-6. ACMP1 signal descriptions
Chip signal name
Module signal
name
Description
I/O
ACMP1_INn
ACMP1_IN[2:0]
Analog voltage inputs
I
ACMP1_OUT
ACMP1_OUT
Comparator output
O
10.3.5 Timer modules
Table 10-7. FTM0 signal descriptions
Chip signal name
Module signal
name
TCLKn
EXTCLK
FTM0_CH[1:0]
CHn
Description
I/O
FTM external clock
I
FTM channel
I/O
Table 10-8. FTM1 signal descriptions
Chip signal name
Module signal
name
TCLKn
EXTCLK
FTM1_CH[1:0]
CHn
Description
I/O
FTM external clock
I
FTM channel
I/O
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
146
Freescale Semiconductor, Inc.
Chapter 10 Signal Multiplexing and Signal Descriptions
Table 10-9. FTM2 signal descriptions
Chip signal name
Module signal
name
Description
TCLKn
EXTCLK
FTM2_CHn
CHn
FTM channel
I/O
FTM2_FLT1
FAULT1
Fault input (1)
I
FTM2_FLT2
FAULT2
Fault input (2)
I
FTM external clock
I/O
I
Table 10-10. RTC signal descriptions
Chip signal name
Module signal
name
RTC_CLKOUT
RTCO
Description
I/O
RTC clock output
O
Table 10-11. PWT signal descriptions
Chip signal name
Module signal
name
Description
I/O
TCLKn
ALTCLK
PWT alternate external clock
O
PWT_IN0
PWTIN[0]
PWT input channel0
I
PWT_IN1
PWTIN[1]
PWT input channel1
I
10.3.6 Communication Interfaces
Table 10-12. SPI0 signal descriptions
Chip signal name
Module signal
name
Description
I/O
SPI0_MISO
MISO
Master Data In, Slave Data Out
I/O
SPI0_MOSI
MOSI
Master Data Out, Slave Data In
I/O
SPI0_SCK
SPSCK
SPI Serial Clock
I/O
SPI0_PCS
SS
Slave Select
I/O
Table 10-13. SPI1 signal descriptions
Chip signal name
Module signal
name
Description
I/O
SPI1_MISO
MISO
Master Data In, Slave Data Out
I/O
SPI1_MOSI
MOSI
Master Data Out, Slave Data In
I/O
SPI1_SCK
SPSCK
SPI Serial Clock
I/O
SPI1_PCS
SS
Slave Select
I/O
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
147
Module signal description tables
Table 10-14. I2C0 signal descriptions
Chip signal name
Module signal
name
I2C0_SCL
SCL
I2C0_SDA
Description
I/O
Bidirectional serial clock line of the I2C system.
SDA
I2C0_ 4WSCLOUT
Bidirectional serial data line of the
Serial clock line output of
I2C0_ 4WSDAOUT
Serial data line output of
I2C0
I2C0
I2C
I/O
system.
I/O
in 4 wire interface configuration
in 4 wire interface configuration
O
O
Table 10-15. I2C1 signal descriptions
Chip signal name
Module signal
name
I2C1_SCL
SCL
I2C1_SDA
SDA
Description
I/O
Bidirectional serial clock line of the I2C system.
Bidirectional serial data line of the
I2C
I/O
system.
I/O
Table 10-16. UART0 signal descriptions
Chip signal name
Module signal
name
Description
I/O
UART0_TX
TxD
Transmit data
I/O
UART0_RX
RxD
Receive data
I
Table 10-17. UART1 signal descriptions
Chip signal name
Module signal
name
Description
I/O
UART1_TX
TxD
Transmit data
I/O
UART1_RX
RxD
Receive data
I
Table 10-18. UART2 signal descriptions
Chip signal name
Module signal
name
Description
I/O
UART2_TX
TxD
Transmit data
I/O
UART2_RX
RxD
Receive data
I
Table 10-19. MSCAN signal descriptions
Chip signal name
Module signal
name
Description
I/O
CAN0_RX
RXCAN
Transmit data
I
CAN0_TX
TXCAN
Receive data
O
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
148
Freescale Semiconductor, Inc.
Chapter 10 Signal Multiplexing and Signal Descriptions
10.3.7 Human-machine interfaces (HMI)
Table 10-20. GPIO signal descriptions
Chip signal name
Module signal
name
PTA[7:0]1
PORTA7-PORTA0
PTB[7:0]
General-purpose input/output
I/O
PORTA15-PORTA8 General-purpose input/output
I/O
1
PORTA23-PORTA16 General-purpose input/output
I/O
1
PORTA31-PORTA24 General-purpose input/output
I/O
PTD[7:0]
PTF[7:0]
I/O
1
PTC[7:0]
PTE[7:0]
Description
1
General-purpose input/output
I/O
1
PORTB15-PORTB8 General-purpose input/output
I/O
1
PORTB23-PORTB16 General-purpose input/output
I/O
1
PORTB31-PORTB24 General-purpose input/output
I/O
PTG[7:0]
PTH[7:0]
1
PTI[6:0]
PORTB7-PORTB0
PORTC6-PORTC0
General-purpose input/output
I/O
1. The available GPIO pins depend on the specific package. See the signal multiplexing section for which exact GPIO signals
are available.
Table 10-21. KBI0 signal descriptions
Chip signal name
Module signal
name
KBI0_Pn
KBI0Pn
Description
I/O
Keyboard interrupt pins, n can be 0 ~ 31
I/O
Table 10-22. KBI1 signal descriptions
Chip signal name
Module signal
name
KBI1_Pn
KBI1Pn
Description
I/O
Keyboard interrupt pins, n can be 0 ~ 31
I/O
Table 10-23. IRQ signal descriptions
Chip signal name
Module signal
name
IRQ
IRQ
Description
IRQ input
I/O
I
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
149
Module signal description tables
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
150
Freescale Semiconductor, Inc.
Chapter 11
Port Control (PORT)
11.1 Introduction
This device has nine sets of I/O ports, which include up to 71 general-purpose I/O pins.
Not all pins are available on all devices.
Many of the I/O pins are shared with on-chip peripheral functions. The peripheral
modules have priority over the I/O, so when a peripheral is enabled, the associated I/O
functions are disabled.
After reset, the shared peripheral functions are disabled so that the pins are controlled by
the parallel I/O except PTA4, PTA5, PTB4 and PTC4 that are default to SWD_DIO,
SWD_CLK, NMI and RESET function. All of the parallel I/O are configured as highimpedance (Hi-Z). The pin control functions for each pin are configured as follows:
• input disabled (GPIOx_PIDR[PID] = 1),
• output disabled ( GPIOx_PDDR[PDD] = 0), and
• internal pullups disabled (PORT_PUE(0/1/2)[PTxPEn] = 0).
Additionally, the parallel I/O that support high drive capability are disabled (HDRVE =
0x00) after reset.
The following three figures show the structures of each I/O pin.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
151
Introduction
PORT_PUE(0/1/2)[PTxPEn]
GPIOx_PDDR[PDD]
GPIOx_PDOR[PDO]
GPIOx_PIDR[PID]
1
0 (except RESET/NMI)
0
Glitch filter
PORT_IOFLT(0/1)
CPU read GPIOx_PDIR[PDI]
Figure 11-1. Normal I/O structure
PORT_PUE(0/1/2)[PTxPEn]
GPIOx_PDDR[PDD]
GPIOx_PDOR[PDO]
GPIOx_PIDR[PID]
1
CPU read GPIOx_PDIR[PDI]
0 (except RESET/NMI)
Glitch filter
PORT_IOFLT(0/1)
0
Figure 11-2. SDA(PTA2)/SCL(PTA3) structure
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
152
Freescale Semiconductor, Inc.
Chapter 11 Port Control (PORT)
PORT_PUE(0/1/2)[PTxPEn]
GPIOx_PDDR[PDD]
GPIOx_PDOR[PDO]
GPIOx_PIDR[PID]
HDRVE
1
CPU read GPIOx_PDIR[PDI]
0 (except RESET/NMI)
Glitch filter
PORT_IOFLT(0/1)
0
Figure 11-3. High drive I/O structure
11.2 Port data and data direction
Reading and writing of parallel I/O is accomplished through the port data registers
(GPIOx_PDIR/PDOR). The direction, input or output, is controlled through the input
disable register (GPIOx_PIDR) and data direction register (GPIOx_PDDR).
After reset, all parallel I/O default to the Hi-Z state. The corresponding bit in port data
direction register (GPIOx_PDDR) or input disable register (GPIOx_PIDR) must be
configured for output or input operation. Each port pin has an input disable bit and an
output enable bit. When GPIOx_PIDR[PID] = 0, a read from GPIOx_PDIR returns the
input value of the associated pin; when GPIOx_PIDR[PID] = 1, a read from
GPIOx_PDIR[PDI] returns 0 except for RESET/NMI.
NOTE
The GPIOx_PDDR must be clear when the corresponding pin is
used as input function to avoid contention. If set the
corresponding GPIOx_PDDR and GPIOx_PIDR bits at same
time, read from GPIOx_PDIR will always read the pin status.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
153
Internal pullup enable
When a peripheral module or system function is in control of a port pin, the data direction
register bit still controls what is returned for reads of the port data register, even though
the peripheral system has overriding control of the actual pin direction.
When a shared analog function is enabled for a pin, all digital pin functions are disabled.
A read of the port data register returns a value of 0 for any bits that have shared analog
functions enabled. In general, whenever a pin is shared with both an alternate digital
function and an analog function, the analog function has priority such that if both of the
digital and analog functions are enabled, the analog function controls the pin.
A write of valid data to a port data register must occur before setting the output enable bit
of an associated port pin. This ensures that the pin will not be driven with an incorrect
data value.
11.3 Internal pullup enable
An internal pullup device can be enabled for each port pin by setting the corresponding
bit in one of the pullup enable registers (PORT_PUE(0/1/2)). The internal pullup device
is disabled if the pin is configured as an output by the parallel I/O control logic, or by any
shared peripheral function, regardless of the state of the corresponding pullup enable
register bit. The internal pullup device is also disabled if the pin is controlled by an
analog function.
NOTE
When configuring I2C0 to use "SDA(PTA2/PTB6) and
SCL(PTA3/PTB7)" pins or I2C1 to use "SDA (PTE0/PTH3)
and SCL (PTE1/PTH4)" pins, and if an application uses internal
pullups instead of external pullups, the internal pullups remain
at present setting when the pins are configured as outputs, but
they are automatically disabled to save power when the output
values are low.
11.4 Input glitch filter setting
A filter is implemented for each port pin that is configured as a digital input. It can be
used as a simple low-pass filter to filter any glitch that is introduced from the pins of
GPIO, FTM0, FTM1, I2C0, I2C1, PWT, IRQ,RESET, NMI and KBI. The glitch width
threshold can be adjusted easily by setting PORT_IOFLT0[FLTDIVn] between 1~4096
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
154
Freescale Semiconductor, Inc.
Chapter 11 Port Control (PORT)
BUSCLKs (or 1~128 LPOCLKs). This configurable glitch filter can take the place of an
on board external analog filter, and greatly improve the EMC performance because any
glitch will not be wrongly sampled or ignored.
Setting register PORT_IOFLT(0/1) can configure the filters of the whole port or
peripheral inputs. For example, setting PORT_IOFLT0[FLTA] will affect all PTAn pins.
Glitches that are shorter than the selected clock period will be filtered out; Glitches that
are more than twice the selected clock period will not be filtered out. It will pass to
internal circuitry.
Pass to
internal rate
100%
Input high/low width
0
1(FLTxxx period)
2(FLTxxx period)
Note: FLTxxx is contents in register PORT_IOFLT(0/1).
Figure 11-4. Input glitch filter
11.5 High current drive
Output high sink/source current drive can be enabled by setting the corresponding bit in
the HDRVE register for . These pins can used as output and input; the pins output high
sink/source current when they are operated as output.
• High-current drive function is disabled, if the pin is configured as an input by the
parallel I/O control logic.
• When configured as any shared peripheral function, high-current drive function still
works on these pins, but only when they are configured as outputs.
11.6 Pin behavior in Stop mode
In Stop mode, all I/O is maintained because internal logic circuitry stays powered up.
Upon recovery, normal I/O function is available to the user.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
155
Port data registers
11.7 Port data registers
PORT memory map
Absolute
address
(hex)
Width
Access
(in bits)
Register name
Reset value
Section/
page
4004_9000
Port Filter Register 0 (PORT_IOFLT0)
32
R/W
00C0_0000h
11.7.1/156
4004_9004
Port Filter Register 1 (PORT_IOFLT1)
32
R/W
0000_0000h
11.7.2/159
4004_9008
Port Pullup Enable Register 0 (PORT_PUE0)
32
R/W
0010_0000h
11.7.3/160
4004_900C
Port Pullup Enable Register 1 (PORT_PUE1)
32
R/W
0000_0000h
11.7.4/165
4004_9010
Port Pullup Enable Register 2 (PORT_PUE2)
32
R/W
0000_0000h
11.7.5/170
4004_9014
Port High Drive Enable Register (PORT_HDRVE)
32
R/W
0000_0000h
11.7.6/172
11.7.1 Port Filter Register 0 (PORT_IOFLT0)
This register sets the filters for input pins. Configure the high/low level glitch width
threshold. Glitches that are shorter than the selected clock period will be filtered out;
glitches that are more than twice the selected clock period will not be filtered out and will
pass to internal circuitry.
Address: 4004_9000h base + 0h offset = 4004_9000h
Bit
R
W
31
30
29
28
Reset
0
0
0
0
0
Bit
R
W
15
14
13
12
11
Reset
0
FLTDIV3
27
FLTDIV2
FLTH
FLTG
0
26
0
25
0
23
22
21
20
19
18
17
16
FLTDIV1
FLTNMI
FLTKBI1
FLTKBI0
FLTRST
0
0
0
1
1
0
0
0
0
0
0
10
9
8
7
6
5
4
3
2
1
0
FLTF
0
24
FLTE
0
0
FLTD
0
0
FLTC
0
0
FLTB
0
0
FLTA
0
0
0
PORT_IOFLT0 field descriptions
Field
31–29
FLTDIV3
Description
Filter Division Set 3
Port Filter Division Set 3
000
001
010
011
100
101
LPOCLK
LPOCLK/2
LPOCLK/4
LPOCLK/8
LPOCLK/16
LPOCLK/32
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
156
Freescale Semiconductor, Inc.
Chapter 11 Port Control (PORT)
PORT_IOFLT0 field descriptions (continued)
Field
Description
110
111
28–26
FLTDIV2
Filter Division Set 2
Port Filter Division Set 2
000
001
010
011
100
101
110
111
25–24
FLTDIV1
LPOCLK/64
LPOCLK/128
BUSCLK/32
BUSCLK/64
BUSCLK/128
BUSCLK/256
BUSCLK/512
BUSCLK/1024
BUSCLK/2048
BUSCLK/4096
Filter Division Set 1
Port Filter Division Set 1
00
01
10
11
BUSCLK/2
BUSCLK/4
BUSCLK/8
BUSCLK/16
23–22
FLTNMI
Filter Selection for Input from NMI
21–20
FLTKBI1
Filter Selection for Input from KBI1
19–18
FLTKBI0
Filter selection for Input from KBI0
17–16
FLTRST
Filter Selection for Input from RESET/IRQ
15–14
FLTH
00
01
10
11
00
01
10
11
00
01
10
11
00
01
10
11
No filter.
Selects FLTDIV1, and will switch to FLTDIV3 in Stop mode automatically.
Selects FLTDIV2, and will switch to FLTDIV3 in Stop mode automatically.
FLTDIV3
No filter
Selects FLTDIV1, and will switch to FLTDIV3 in Stop mode automatically.
Selects FLTDIV2, and will switch to FLTDIV3 in Stop mode automatically.
FLTDIV3
No filter.
Selects FLTDIV1, and will switch to FLTDIV3 in Stop mode automatically.
Selects FLTDIV2, and will switch to FLTDIV3 in Stop mode automatically.
FLTDIV3
No filter.
Selects FLTDIV1, and will switch to FLTDIV3 in Stop mode automatically.
Selects FLTDIV2, and will switch to FLTDIV3 in Stop mode automatically.
FLTDIV3
Filter Selection for Input from PTH
00
BUSCLK
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
157
Port data registers
PORT_IOFLT0 field descriptions (continued)
Field
Description
01
10
11
FLTDIV1
FLTDIV2
FLTDIV3
13–12
FLTG
Filter Selection for Input from PTG
11–10
FLTF
Filter Selection for Input from PTF
9–8
FLTE
Filter Selection for Input from PTD
7–6
FLTD
Filter Selection for Input from PTD
5–4
FLTC
Filter Selection for Input from PTC
3–2
FLTB
Filter Selection for Input from PTB
FLTA
Filter Selection for Input from PTA
00
01
10
11
00
01
10
11
00
01
10
11
00
01
10
11
00
01
10
11
00
01
10
11
00
01
10
11
BUSCLK
FLTDIV1
FLTDIV2
FLTDIV3
BUSCLK
FLTDIV1
FLTDIV2
FLTDIV3
BUSCLK
FLTDIV1
FLTDIV2
FLTDIV3
BUSCLK
FLTDIV1
FLTDIV2
FLTDIV3
BUSCLK
FLTDIV1
FLTDIV2
FLTDIV3
BUSCLK
FLTDIV1
FLTDIV2
FLTDIV3
BUSCLK
FLTDIV1
FLTDIV2
FLTDIV3
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
158
Freescale Semiconductor, Inc.
Chapter 11 Port Control (PORT)
11.7.2 Port Filter Register 1 (PORT_IOFLT1)
This register sets the filters for input pins. Configure the high/low level glitch width
threshold. Glitches that are shorter than the selected clock period will be filtered out;
glitches that are more than twice the selected clock period will not be filtered out and will
pass to internal circuitry.
Address: 4004_9000h base + 4h offset = 4004_9004h
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
0
R
W
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
R
W
Reset
FLTI2C1
FLTI2C0
FLTPWT
FLTFTM1
FLTFTM0
FLTIRQ
0
0
0
0
0
0
0
0
0
0
0
0
0
0
FLTI
0
0
0
PORT_IOFLT1 field descriptions
Field
Description
31–16
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
15–14
FLTI2C1
Filter Selection For Input from SCL1/SDA1
13–12
FLTI2C0
Filter Selection For Input from SCL0/SDA0
11–10
FLTPWT
Filter Selection For Input from PWT_IN1/PWT_IN0
9–8
FLTFTM1
Filter Selection For Input from FTM1CH0/FTM1CH1
00
01
10
11
00
01
10
11
00
01
10
11
00
01
10
11
No filter
Select FLTDIV1
Select FLTDIV2
Select BUSCLK
No filter
Select FLTDIV1
Select FLTDIV2
Select BUSCLK
No filter
Select FLTDIV1
Select FLTDIV2
Select FLTDIV3
No filter
Select FLTDIV1
Select FLTDIV2
Select FLTDIV3
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
159
Port data registers
PORT_IOFLT1 field descriptions (continued)
Field
Description
7–6
FLTFTM0
Filter Selection For Input from FTM0CH0/FTM0CH1
00
01
10
11
5–4
FLTIRQ
No filter
Select FLTDIV1
Select FLTDIV2
Select FLTDIV3
Filter Selection for Input from IRQ
00
01
10
11
3–2
Reserved
No filter
Selects FLTDIV1, and will switch to FLTDIV3 in Stop mode automatically.
Selects FLTDIV2, and will switch to FLTDIV3 in Stop mode automatically.
FLTDIV3
This field is reserved.
This read-only field is reserved and always has the value 0.
FLTI
Filter Selection for Input from PTI
00
01
10
11
BUSCLK
FLTDIV1
FLTDIV2
FLTDIV3
11.7.3 Port Pullup Enable Register 0 (PORT_PUE0)
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
R
W
PTDPE7
PTDPE6
PTDPE5
PTDPE4
PTDPE3
PTDPE2
PTDPE1
PTDPE0
PTCPE7
PTCPE6
PTCPE5
PTCPE4
PTCPE3
PTCPE2
PTCPE1
PTCPE0
Reset
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
R
W
PTBPE7
PTBPE6
PTBPE5
PTBPE4
PTBPE3
PTBPE2
PTBPE1
PTBPE0
PTAPE7
PTAPE6
PTAPE5
PTAPE4
PTAPE3
PTAPE2
PTAPE1
PTAPE0
Address: 4004_9000h base + 8h offset = 4004_9008h
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
PORT_PUE0 field descriptions
Field
31
PTDPE7
Description
Pull Enable for Port D Bit 7
This control field determines if the internal pullup device is enabled for the associated PTD pin. For port D
pins that are configured as outputs or Hi-Z, this field has no effect.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
160
Freescale Semiconductor, Inc.
Chapter 11 Port Control (PORT)
PORT_PUE0 field descriptions (continued)
Field
Description
0
1
30
PTDPE6
Pull Enable for Port D Bit 6
This control field determines if the internal pullup device is enabled for the associated PTD pin. For port D
pins that are configured as outputs or Hi-Z, this field has no effect.
0
1
29
PTDPE5
This control field determines if the internal pullup device is enabled for the associated PTD pin. For port D
pins that are configured as outputs or Hi-Z, this field has no effect.
This control bit determines if the internal pullup device is enabled for the associated PTD pin. For port D
pins that are configured as outputs or Hi-Z, these bits have no effect.
This control field determines if the internal pullup device is enabled for the associated PTD pin. For port D
pins that are configured as outputs or Hi-Z, this field has no effect.
This control field determines if the internal pullup device is enabled for the associated PTD pin. For port D
pins that are configured as outputs or Hi-Z, this field has no effect.
Pullup is disabled for port D bit 2.
Pullup is enabled for port D bit 2.
Pull Enable for Port D Bit 1
This control field determines if the internal pullup device is enabled for the associated PTD pin. For port D
pins that are configured as outputs or Hi-Z, this field has no effect.
0
1
24
PTDPE0
Pullup is disabled for port D bit 3.
Pullup is enabled for port D bit 3.
Pull Enable for Port D Bit 2
0
1
25
PTDPE1
Pullup is disabled for port D bit 4.
Pullup is enabled for port D bit 4.
Pull Enable for Port D Bit 3
0
1
26
PTDPE2
Pullup is disabled for port D bit 5.
Pullup is enabled for port D bit 5.
Pull Enable for Port D Bit 4
0
1
27
PTDPE3
Pullup is disabled for port D bit 6.
Pullup is enabled for port D bit 6.
Pull Enable for Port D Bit 5
0
1
28
PTDPE4
Pullup is disabled for port D bit 7.
Pullup is enabled for port D bit 7.
Pullup is disabled for port D bit 1.
Pullup is enabled for port D bit 1.
Pull Enable for Port D Bit 0
This control field determines if the internal pullup device is enabled for the associated PTD pin. For port D
pins that are configured as outputs or Hi-Z, this field has no effect.
0
1
Pullup is disabled for port D bit 0.
Pullup is enabled for port D bit 0.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
161
Port data registers
PORT_PUE0 field descriptions (continued)
Field
23
PTCPE7
Description
Pull Enable for Port C Bit 7
This control field determines if the internal pullup device is enabled for the associated PTC pin. For port C
pins that are configured as outputs or Hi-Z, this field has no effect.
0
1
22
PTCPE6
Pull Enable for Port C Bit 6
This control field determines if the internal pullup device is enabled for the associated PTC pin. For port C
pins that are configured as outputs or Hi-Z, this field has no effect.
0
1
21
PTCPE5
This control field determines if the internal pullup device is enabled for the associated PTC pin. For port C
pins that are configured as outputs or Hi-Z, this field has no effect.
This control field determines if the internal pullup device is enabled for the associated PTC pin. For port C
pins that are configured as outputs or Hi-Z, this field has no effect.
This control field determines if the internal pullup device is enabled for the associated PTC pin. For port C
pins that are configured as outputs or Hi-Z, this field has no effect.
This control field determines if the internal pullup device is enabled for the associated PTC pin. For port C
pins that are configured as outputs or Hi-Z, this field has no effect.
Pullup is disabled for port C bit 2.
Pullup is enabled for port C bit 2.
Pull Enable for Port C Bit 1
This control field determines if the internal pullup device is enabled for the associated PTC pin. For port C
pins that are configured as outputs or Hi-Z, this field has no effect.
0
1
16
PTCPE0
Pullup is disabled for port C bit 3.
Pullup is enabled for port C bit 3.
Pull Enable for Port C Bit 2
0
1
17
PTCPE1
Pullup is disabled for port C bit 4.
Pullup is enabled for port C bit 4.
Pull Enable for Port C Bit 3
0
1
18
PTCPE2
Pullup is disabled for port C bit 5.
Pullup is enabled for port C bit 5.
Pull Enable for Port C Bit 4
0
1
19
PTCPE3
Pullup is disabled for port C bit 6.
Pullup is enabled for port C bit 6.
Pull Enable for Port C Bit 5
0
1
20
PTCPE4
Pullup is disabled for port C bit 7.
Pullup is enabled for port C bit 7.
Pullup is disabled for port C bit 1.
Pullup is enabled for port C bit 1.
Pull Enable for Port C Bit 0
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
162
Freescale Semiconductor, Inc.
Chapter 11 Port Control (PORT)
PORT_PUE0 field descriptions (continued)
Field
Description
This control field determines if the internal pullup device is enabled for the associated PTC pin. For port C
pins that are configured as outputs or Hi-Z, this field has no effect.
0
1
15
PTBPE7
Pull Enable for Port B Bit 7
This control field determines if the internal pullup device is enabled for the associated PTB pin. For port B
pins that are configured as outputs or Hi-Z, this field has no effect.
0
1
14
PTBPE6
This control field determines if the internal pullup device is enabled for the associated PTB pin. For port B
pins that are configured as outputs or Hi-Z, this field has no effect.
This control field determines if the internal pullup device is enabled for the associated PTB pin. For port B
pins that are configured as outputs or Hi-Z, this field has no effect.
This control field determines if the internal pullup device is enabled for the associated PTB pin. For port B
pins that are configured as outputs or Hi-Z, this field has no effect.
This control field determines if the internal pullup device is enabled for the associated PTB pin. For port B
pins that are configured as outputs or Hi-Z, this field has no effect.
Pullup is disabled for port B bit 3.
Pullup is enabled for port B bit 3.
Pull Enable for Port B Bit 2
This control field determines if the internal pullup device is enabled for the associated PTB pin. For port B
pins that are configured as outputs or Hi-Z, this field has no effect.
0
1
9
PTBPE1
Pullup is disabled for port B bit 4.
Pullup is enabled for port B bit 4.
Pull Enable for Port B Bit 3
0
1
10
PTBPE2
Pullup is disabled for port B bit 5.
Pullup is enabled for port B bit 5.
Pull Enable for Port B Bit 4
0
1
11
PTBPE3
Pullup is disabled for port B bit 6.
Pullup is enabled for port B bit 6.
Pull Enable for Port B Bit 5
0
1
12
PTBPE4
Pullup is disabled for port B bit 7.
Pullup is enabled for port B bit 7.
Pull Enable for Port B Bit 6
0
1
13
PTBPE5
Pullup is disabled for port C bit 0.
Pullup is enabled for port C bit 0.
Pullup is disabled for port B bit 2.
Pullup is enabled for port B bit 2.
Pull Enable for Port B Bit 1
This control field determines if the internal pullup device is enabled for the associated PTB pin. For port B
pins that are configured as outputs or Hi-Z, tthis field has no effect.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
163
Port data registers
PORT_PUE0 field descriptions (continued)
Field
Description
0
1
8
PTBPE0
Pull Enable for Port B Bit 0
This control field determines if the internal pullup device is enabled for the associated PTB pin. For port B
pins that are configured as outputs or Hi-Z, this field has no effect.
0
1
7
PTAPE7
This control field determines if the internal pullup device is enabled for the associated PTA pin. For port A
pins that are configured as outputs or Hi-Z, this field has no effect.
This control field determines if the internal pullup device is enabled for the associated PTA pin. For port A
pins that are configured as outputs or Hi-Z, this field has no effect.
This control field determines if the internal pullup device is enabled for the associated PTA pin. For port A
pins that are configured as outputs or Hi-Z, this field has no effect.
Pullup is disabled for port A bit 5.
Pullup is enabled for port A bit 5.
Pull Enable for Port A Bit 4
This control field determines if the internal pullup device is enabled for the associated PTA pin. For port A
pins that are configured as outputs or Hi-Z, this field has no effect.
0
1
3
PTAPE3
Pullup is disabled for port A bit 6.
Pullup is enabled for port A bit 6.
Pull Enable for Port A Bit 5
0
1
4
PTAPE4
Pullup is disabled for port A bit 7.
Pullup is enabled for port A bit 7.
Pull Enable for Port A Bit 6
0
1
5
PTAPE5
Pullup is disabled for port B bit 0.
Pullup is enabled for port B bit 0.
Pull Enable for Port A Bit 7
0
1
6
PTAPE6
Pullup is disabled for port B bit 1.
Pullup is enabled for port B bit 1.
Pullup is disabled for port A bit 4.
Pullup is enabled for port A bit 4.
Pull Enable for Port A Bit 3
This control field determines if the internal pullup device is enabled for the associated PTA pin. For port A
pins that are configured as outputs or Hi-Z, this field has no effect.
NOTE: When configuring to use this pin as output high for IIC, the internal pullup device remains active
when PTAPE3 is set. It is automatically disabled to save power when output low.
0
1
2
PTAPE2
Pullup is disabled for port A bit 3.
Pullup is enabled for port A bit 3.
Pull Enable for Port A Bit 2
This control field determines if the internal pullup device is enabled for the associated PTA pin. For port A
pins that are configured as outputs or Hi-Z, this field has no effect.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
164
Freescale Semiconductor, Inc.
Chapter 11 Port Control (PORT)
PORT_PUE0 field descriptions (continued)
Field
Description
NOTE: When configuring to use this pin as output high for IIC, the internal pullup device remains active
when PTAPE2 is set. It is automatically disabled to save power when output low.
0
1
1
PTAPE1
Pullup is disabled for port A bit 2.
Pullup is enabled for port A bit 2.
Pull Enable for Port A Bit 1
This control field determines if the internal pullup device is enabled for the associated PTA pin. For port A
pins that are configured as outputs or Hi-Z, this field has no effect.
0
1
0
PTAPE0
Pullup is disabled for port A bit 1.
Pullup is enabled for port A bit 1.
Pull Enable for Port A Bit 0
This control field determines if the internal pullup device is enabled for the associated PTA pin. For port A
pins that are configured as outputs or Hi-Z, this field has no effect.
0
1
Pullup is disabled for port A bit 0.
Pullup is enabled for port A bit 0.
11.7.4 Port Pullup Enable Register 1 (PORT_PUE1)
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
R
W
PTHPE7
PTHPE6
PTHPE5
PTHPE4
PTHPE3
PTHPE2
PTHPE1
PTHPE0
PTGPE7
PTGPE6
PTGPE5
PTGPE4
PTGPE3
PTGPE2
PTGPE1
PTGPE0
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
R
W
PTFPE7
PTFPE6
PTFPE5
PTFPE4
PTFPE3
PTFPE2
PTFPE1
PTFPE0
PTEPE7
PTEPE6
PTEPE5
PTEPE4
PTEPE3
PTEPE2
PTEPE1
PTEPE0
Address: 4004_9000h base + Ch offset = 4004_900Ch
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
PORT_PUE1 field descriptions
Field
31
PTHPE7
Description
Pull Enable for Port H Bit 7
This control field determines if the internal pullup device is enabled for the associated PTH pin. For port H
pins that are configured as outputs or Hi-Z, this field has no effect.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
165
Port data registers
PORT_PUE1 field descriptions (continued)
Field
Description
0
1
30
PTHPE6
Pull Enable for Port H Bit 6
This control field determines if the internal pullup device is enabled for the associated PTH pin. For port H
pins that are configured as outputs or Hi-Z, this field has no effect.
0
1
29
PTHPE5
This control field determines if the internal pullup device is enabled for the associated PTH pin. For port H
pins that are configured as outputs or Hi-Z, this field has no effect.
This control field determines if the internal pullup device is enabled for the associated PTH pin. For port H
pins that are configured as outputs or Hi-Z, this field has no effect.
This control field determines if the internal pullup device is enabled for the associated PTH pin. For port H
pins that are configured as outputs or Hi-Z, this field has no effect.
This control field determines if the internal pullup device is enabled for the associated PTH pin. For port H
pins that are configured as outputs or Hi-Z, this field has no effect.
Pullup is disabled for port H bit 2.
Pullup is enabled for port H bit 2.
Pull Enable for Port H Bit 1
This control field determines if the internal pullup device is enabled for the associated PTH pin. For port H
pins that are configured as outputs or Hi-Z, this field has no effect.
0
1
24
PTHPE0
Pullup is disabled for port H bit 3.
Pullup is enabled for port H bit 3.
Pull Enable for Port H Bit 2
0
1
25
PTHPE1
Pullup is disabled for port H bit 4.
Pullup is enabled for port H bit 4.
Pull Enable for Port H Bit 3
0
1
26
PTHPE2
Pullup is disabled for port H bit 5.
Pullup is enabled for port H bit 5.
Pull Enable for Port H Bit 4
0
1
27
PTHPE3
Pullup is disabled for port H bit 6.
Pullup is enabled for port H bit 6.
Pull Enable for Port H Bit 5
0
1
28
PTHPE4
Pullup is disabled for port H bit 7.
Pullup is enabled for port H bit 7.
Pullup is disabled for port H bit 1.
Pullup is enabled for port H bit 1.
Pull Enable for Port H Bit 0
This control field determines if the internal pullup device is enabled for the associated PTH pin. For port H
pins that are configured as outputs or Hi-Z, this field has no effect.
0
1
Pullup is disabled for port H bit 0.
Pullup is enabled for port H bit 0.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
166
Freescale Semiconductor, Inc.
Chapter 11 Port Control (PORT)
PORT_PUE1 field descriptions (continued)
Field
23
PTGPE7
Description
Pull Enable for Port G Bit 7
This control field determines if the internal pullup device is enabled for the associated PTG pin. For port G
pins that are configured as outputs or Hi-Z, this field has no effect.
0
1
22
PTGPE6
Pull Enable for Port G Bit 6
This control field determines if the internal pullup device is enabled for the associated PTG pin. For port G
pins that are configured as outputs or Hi-Z, this field has no effect.
0
1
21
PTGPE5
This control field determines if the internal pullup device is enabled for the associated PTG pin. For port G
pins that are configured as outputs or Hi-Z, this field has no effect.
This control field determines if the internal pullup device is enabled for the associated PTG pin. For port G
pins that are configured as outputs or Hi-Z, this field has no effect.
This control field determines if the internal pullup device is enabled for the associated PTG pin. For port G
pins that are configured as outputs or Hi-Z, this field has no effect.
This control field determines if the internal pullup device is enabled for the associated PTG pin. For port G
pins that are configured as outputs or Hi-Z, this field has no effect.
Pullup is disabled for port G bit 2.
Pullup is enabled for port G bit 2.
Pull Enable for Port G Bit 1
This control field determines if the internal pullup device is enabled for the associated PTG pin. For port G
pins that are configured as outputs or Hi-Z, this field has no effect.
0
1
16
PTGPE0
Pullup is disabled for port G bit 3.
Pullup is enabled for port G bit 3.
Pull Enable for Port G Bit 2
0
1
17
PTGPE1
Pullup is disabled for port G bit 4.
Pullup is enabled for port G bit 4.
Pull Enable for Port G Bit 3
0
1
18
PTGPE2
Pullup is disabled for port G bit 5.
Pullup is enabled for port G bit 5.
Pull Enable for Port G Bit 4
0
1
19
PTGPE3
Pullup is disabled for port G bit 6.
Pullup is enabled for port G bit 6.
Pull Enable for Port G Bit 5
0
1
20
PTGPE4
Pullup is disabled for port G bit 7.
Pullup is enabled for port G bit 7.
Pullup is disabled for port G bit 1.
Pullup is enabled for port G bit 1.
Pull Enable for Port G Bit 0
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
167
Port data registers
PORT_PUE1 field descriptions (continued)
Field
Description
This control field determines if the internal pullup device is enabled for the associated PTG pin. For port G
pins that are configured as outputs or Hi-Z, this field has no effect.
0
1
15
PTFPE7
Pull Enable for Port F Bit 7
This control field determines if the internal pullup device is enabled for the associated PTF pin. For port F
pins that are configured as outputs or Hi-Z, this field has no effect.
0
1
14
PTFPE6
This control field determines if the internal pullup device is enabled for the associated PTF pin. For port F
pins that are configured as outputs or Hi-Z, this field has no effect.
This control field determines if the internal pullup device is enabled for the associated PTF pin. For port F
pins that are configured as outputs or Hi-Z, this field has no effect.
This control field determines if the internal pullup device is enabled for the associated PTF pin. For port F
pins that are configured as outputs or Hi-Z, this field has no effect.
This control field determines if the internal pullup device is enabled for the associated PTF pin. For port F
pins that are configured as outputs or Hi-Z, this field has no effect.
Pullup is disabled for port F bit 3.
Pullup is enabled for port F bit 3.
Pull Enable for Port F Bit 2
This control field determines if the internal pullup device is enabled for the associated PTF pin. For port F
pins that are configured as outputs or Hi-Z, this field has no effect.
0
1
9
PTFPE1
Pullup is disabled for port F bit 4.
Pullup is enabled for port F bit 4.
Pull Enable for Port F Bit 3
0
1
10
PTFPE2
Pullup is disabled for port F bit 5.
Pullup is enabled for port F bit 5.
Pull Enable for Port F Bit 4
0
1
11
PTFPE3
Pullup is disabled for port F bit 6.
Pullup is enabled for port F bit 6.
Pull Enable for Port F Bit 5
0
1
12
PTFPE4
Pullup is disabled for port F bit 7.
Pullup is enabled for port F bit 7.
Pull Enable for Port F Bit 6
0
1
13
PTFPE5
Pullup is disabled for port G bit 0.
Pullup is enabled for port G bit 0.
Pullup is disabled for port F bit 2.
Pullup is enabled for port F bit 2.
Pull Enable for Port F Bit 1
This control field determines if the internal pullup device is enabled for the associated PTF pin. For port F
pins that are configured as outputs or Hi-Z, this field has no effect.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
168
Freescale Semiconductor, Inc.
Chapter 11 Port Control (PORT)
PORT_PUE1 field descriptions (continued)
Field
Description
0
1
8
PTFPE0
Pull Enable for Port F Bit 0
This control field determines if the internal pullup device is enabled for the associated PTF pin. For port F
pins that are configured as outputs or Hi-Z, this field has no effect.
0
1
7
PTEPE7
This control field determines if the internal pullup device is enabled for the associated PTE pin. For port E
pins that are configured as outputs or Hi-Z, this field has no effect.
This control field determines if the internal pullup device is enabled for the associated PTE pin. For port E
pins that are configured as outputs or Hi-Z, this field has no effect.
This control field determines if the internal pullup device is enabled for the associated PTE pin. For port E
pins that are configured as outputs or Hi-Z, this field has no effect.
This control field determines if the internal pullup device is enabled for the associated PTE pin. For port E
pins that are configured as outputs or Hi-Z, this field has no effect.
Pullup is disabled for port E bit 4.
Pullup is enabled for port E bit 4.
Pull Enable for Port E Bit 3
This control field determines if the internal pullup device is enabled for the associated PTE pin. For port E
pins that are configured as outputs or Hi-Z, this field has no effect.
0
1
2
PTEPE2
Pullup is disabled for port E bit 5.
Pullup is enabled for port E bit 5.
Pull Enable for Port E Bit 4
0
1
3
PTEPE3
Pullup is disabled for port E bit 6.
Pullup is enabled for port E bit 6.
Pull Enable for Port E Bit 5
0
1
4
PTEPE4
Pullup is disabled for port E bit 7.
Pullup is enabled for port E bit 7.
Pull Enable for Port E Bit 6
0
1
5
PTEPE5
Pullup is disabled for port F bit 0.
Pullup is enabled for port F bit 0.
Pull Enable for Port E Bit 7
0
1
6
PTEPE6
Pullup is disabled for port F bit 1.
Pullup is enabled for port F bit 1.
Pullup is disabled for port E bit 3.
Pullup is enabled for port E bit 3.
Pull Enable for Port E Bit 2
This control field determines if the internal pullup device is enabled for the associated PTE pin. For port E
pins that are configured as outputs or Hi-Z, this field has no effect.
0
1
Pullup is disabled for port E bit 2.
Pullup is enabled for port E bit 2.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
169
Port data registers
PORT_PUE1 field descriptions (continued)
Field
Description
1
PTEPE1
Pull Enable for Port E Bit 1
This control field determines if the internal pullup device is enabled for the associated PTE pin. For port E
pins that are configured as outputs or Hi-Z, this field has no effect.
0
1
0
PTEPE0
Pullup is disabled for port E bit 1.
Pullup is enabled for port E bit 1.
Pull Enable for Port E Bit 0
This control field determines if the internal pullup device is enabled for the associated PTE pin. For port E
pins that are configured as outputs or Hi-Z, this field has no effect.
0
1
Pullup is disabled for port E bit 0.
Pullup is enabled for port E bit 0.
11.7.5 Port Pullup Enable Register 2 (PORT_PUE2)
Address: 4004_9000h base + 10h offset = 4004_9010h
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
0
R
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
PTIPE6
PTIPE5
PTIPE4
PTIPE3
PTIPE2
PTIPE1
PTIPE0
W
0
0
0
0
0
0
0
0
0
0
0
0
R
W
Reset
0
0
0
0
0
PORT_PUE2 field descriptions
Field
31–7
Reserved
6
PTIPE6
Description
This field is reserved.
This read-only field is reserved and always has the value 0.
Pull Enable for Port I Bit 6
This control field determines if the internal pullup device is enabled for the associated PTI pin. For port I
pins that are configured as outputs or Hi-Z, this field has no effect.
0
1
5
PTIPE5
Pullup is disabled for port I bit 6.
Pullup is enabled for port I bit 6.
Pull Enable for Port I Bit 5
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
170
Freescale Semiconductor, Inc.
Chapter 11 Port Control (PORT)
PORT_PUE2 field descriptions (continued)
Field
Description
This control field determines if the internal pullup device is enabled for the associated PTI pin. For port I
pins that are configured as outputs or Hi-Z, this field has no effect.
0
1
4
PTIPE4
Pull Enable for Port I Bit 4
This control field determines if the internal pullup device is enabled for the associated PTI pin. For port I
pins that are configured as outputs or Hi-Z, this field has no effect.
0
1
3
PTIPE3
This control field determines if the internal pullup device is enabled for the associated PTI pin. For port I
pins that are configured as outputs or Hi-Z, this field has no effect.
This control field determines if the internal pullup device is enabled for the associated PTI pin. For port I
pins that are configured as outputs or Hi-Z, this field has no effect.
Pullup is disabled for port I bit 2.
Pullup is enabled for port I bit 2.
Pull Enable for Port I Bit 1
This control field determines if the internal pullup device is enabled for the associated PTI pin. For port I
pins that are configured as outputs or Hi-Z, this field has no effect.
0
1
0
PTIPE0
Pullup is disabled for port I bit 3.
Pullup is enabled for port I bit 3.
Pull Enable for Port I Bit 2
0
1
1
PTIPE1
Pullup is disabled for port I bit 4.
Pullup is enabled for port I bit 4.
Pull Enable for Port I Bit 3
0
1
2
PTIPE2
Pullup is disabled for port I bit 5.
Pullup is enabled for port I bit 5.
Pullup is disabled for port I bit 1.
Pullup is enabled for port I bit 1.
Pull Enable for Port I Bit 0
This control field determines if the internal pullup device is enabled for the associated PTI pin. For port I
pins that are configured as outputs or Hi-Z, this field has no effect.
0
1
Pullup is disabled for port I bit 0.
Pullup is enabled for port I bit 0.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
171
Port data registers
11.7.6 Port High Drive Enable Register (PORT_HDRVE)
Address: 4004_9000h base + 14h offset = 4004_9014h
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
0
R
W
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
0
R
PTH1 PTH0 PTE1 PTE0 PTD1 PTD0 PTB5 PTB4
W
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
PORT_HDRVE field descriptions
Field
31–8
Reserved
7
PTH1
Description
This field is reserved.
This read-only field is reserved and always has the value 0.
High Current Drive Capability of PTH1
This read/write field enables the high-current drive capability of PTH1.
0
1
6
PTH0
High Current Drive Capability of PTH0
This read/write field enables the high current drive capability of PTH0.
0
1
5
PTE1
This read/write field enables the high current drive capability of PTE1.
This read/write field enables the high current drive capability of PTE0.
PTE0 is disabled to offer high current drive capability.
PTE0 is enable to offer high current drive capability.
High Current Drive Capability of PTD1
This read/write field enables the high current drive capability of PTD1.
0
1
2
PTD0
PTE1 is disabled to offer high current drive capability.
PTE1 is enabled to offer high current drive capability.
High Current Drive Capability of PTE0
0
1
3
PTD1
PTH0 is disabled to offer high current drive capability.
PTH0 is enabled to offer high current drive capability.
High Current Drive Capability of PTE1
0
1
4
PTE0
PTH1 is disabled to offer high current drive capability.
PTH1 is enabled to offer high current drive capability.
PTD1 is disabled to offer high current drive capability.
PTD1 is enable to offer high current drive capability.
High Current Drive Capability of PTD0
This read/write field enables the high current drive capability of PTD0
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
172
Freescale Semiconductor, Inc.
Chapter 11 Port Control (PORT)
PORT_HDRVE field descriptions (continued)
Field
Description
0
1
1
PTB5
High Current Drive Capability of PTB5
This read/write field enables the high current drive capability of PTB5
0
1
0
PTB4
PTD0 is disabled to offer high current drive capability.
PTD0 is enabled to offer high current drive capability.
PTB5 is disabled to offer high current drive capability.
PTB5 is enabled to offer high current drive capability.
High Current Drive Capability of PTB4
This read/write field enables the high current drive capability of PTB4
0
1
PTB4 is disabled to offer high current drive capability.
PTB4 is enabled to offer high current drive capability.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
173
Port data registers
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
174
Freescale Semiconductor, Inc.
Chapter 12
System Integration Module (SIM)
12.1 Introduction
The system integration module (SIM) provides system control and chip configuration
registers.
12.1.1 Features
The features of the SIM module are listed below.
•
•
•
•
Reset status and device ID information
System interconnection configuration and special pin enable
Pin re-map control
System clock gating control and clock divide
12.2 Memory map and register definition
The SIM module contains many fields for selecting the clock source and dividers for
various module clocks.
SIM memory map
Absolute
address
(hex)
Register name
Width
Access
(in bits)
Reset value
Section/
page
4004_8000
System Reset Status and ID Register (SIM_SRSID)
32
R
See section
12.2.1/176
4004_8004
System Options Register 0 (SIM_SOPT0)
32
R/W
See section
12.2.2/179
4004_8008
System Options Register (SIM_SOPT1)
32
R/W
0000_0000h
12.2.3/182
4004_800C
Pin Selection Register 0 (SIM_PINSEL0)
32
R/W
0000_0000h
12.2.4/184
4004_8010
Pin Selection Register 1 (SIM_PINSEL1)
32
R/W
0000_0000h
12.2.5/186
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
175
Memory map and register definition
SIM memory map (continued)
Absolute
address
(hex)
Width
Access
(in bits)
Register name
Reset value
Section/
page
4004_8014
System Clock Gating Control Register (SIM_SCGC)
32
R/W
0000_3000h
12.2.6/188
4004_8018
Universally Unique Identifier Low Register (SIM_UUIDL)
32
R
Undefined
12.2.7/192
4004_801C
Universally Unique Identifier Middle Low Register
(SIM_UUIDML)
32
R
Undefined
12.2.8/192
4004_8020
Universally Unique Identifier Middle High Register
(SIM_UUIDMH)
32
R
Undefined
12.2.9/193
4004_8024
Clock Divider Register (SIM_CLKDIV)
32
R/W
See section
12.2.10/193
12.2.1 System Reset Status and ID Register (SIM_SRSID)
Address: 4004_8000h base + 0h offset = 4004_8000h
Bit
31
30
29
28
27
FAMID
R
26
25
24
23
22
SUBFAMID
21
20
19
18
RevID
17
16
PINID
Reset
LVD
0
0
0
0
0
0
0
0
0
0
1
1
1
1
0
0
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
SACKERR
0
MDMAP
SW
LOCKUP
0
POR
PIN
WDOG
LOC
LVD
W
0
0
0
0
0
0
0
0
0
0
0
0
0
1
u*
0
0
0
0
0
0
1
1
0
0
0
R
0
W
Reset
LVD
0
0
0
0
0
0
0
0
* Notes:
• RevID field: Decided by device revision number.
• PINID field: Decided by device pin number.
• u = Unaffected by reset.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
176
Freescale Semiconductor, Inc.
Chapter 12 System Integration Module (SIM)
SIM_SRSID field descriptions
Field
31–28
FAMID
27–24
SUBFAMID
Description
Kinetis family ID
0000
other
KE0x family.
Reserved.
Kinetis sub-family ID
0100
0110
other
KEx4 sub-family
KEx6 sub-family
Reserved
23–20
RevID
Device Revision Number
19–16
PINID
Device Pin ID
0000
0001
0010
0011
0100
0101
0110
0111
1000
1010
other
8-pin
16-pin
20-pin
24-pin
32-pin
44-pin
48-pin
64-pin
80-pin
100-pin
Reserved
15–14
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
13
SACKERR
Stop Mode Acknowledge Error Reset
Indicates that after an attempt to enter Stop mode, a reset has been caused by the failure of one or more
IICs to acknowledge within approximately one second to enter stop mode.
0
1
Reset is not caused by peripheral failure to acknowledge attempt to enter Stop mode.
Reset is caused by peripheral failure to acknowledge attempt to enter Stop mode.
12
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
11
MDMAP
MDM-AP System Reset Request
Indicates a reset has been caused by the host debugger system setting of the System Reset Request field
in the MDM-AP Control Register.
0
1
10
SW
Reset is not caused by host debugger system setting of the System Reset Request bit.
Reset is caused by host debugger system setting of the System Reset Request bit.
Software
Indicates a reset has been caused by software setting of SYSRESETREQ bit in Application Interrupt and
Reset Control Register in the ARM core.
0
1
Reset is not caused by software setting of SYSRESETREQ bit.
Reset caused by software setting of SYSRESETREQ bit
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
177
Memory map and register definition
SIM_SRSID field descriptions (continued)
Field
9
LOCKUP
Description
Core Lockup
Indicates a reset has been caused by the ARM core indication of a LOCKUP event.
0
1
8
Reserved
7
POR
Reset is not caused by core LOCKUP event.
Reset is caused by core LOCKUP event.
This field is reserved.
This read-only field is reserved and always has the value 0.
Power-On Reset
Causes reset by the power-on detection logic. When the internal supply voltage is ramping up, the lowvoltage reset (LVR) status field is also set at that time, to indicate that the reset has occurred while the
internal supply was below the LVR threshold.
NOTE: This bit POR to 1, LVR to uncertain value and reset to 0 at any other conditions.
0
1
6
PIN
External Reset Pin
Causes reset by an active low-level on the external reset pin.
0
1
5
WDOG
2
LOC
Causes reset by the WDOG timer timing out. This reset source may be blocked by WDOG_CS1[EN] = 0.
Reset is not caused by WDOG timeout.
Reset is caused by WDOG timeout.
This field is reserved.
This read-only field is reserved and always has the value 0.
Internal Clock Source Module Reset
Causes reset by an ICS module reset.
0
1
1
LVD
Reset is not caused by external reset pin.
Reset came from external reset pin.
Watchdog (WDOG)
0
1
4–3
Reserved
Reset not caused by POR.
POR caused reset.
Reset is not caused by the ICS module.
Reset is caused by the ICS module.
Low Voltage Detect
If PMC_SPMSC1[LVDRE] is set in Run mode or both PMC_SPMSC1[LVDRE] and
PMC_SPMSC1[LVDSE] are set in Stop mode, and the supply drops below the LVD trip voltage, an LVD
reset will occur. This field is also set by POR.
NOTE: This field is reset to 1 on POR and LVR, and reset to 0 on other reset.
0
1
0
Reserved
Reset is not caused by LVD trip or POR.
Reset is caused by LVD trip or POR.
This field is reserved.
This read-only field is reserved and always has the value 0.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
178
Freescale Semiconductor, Inc.
Chapter 12 System Integration Module (SIM)
12.2.2 System Options Register 0 (SIM_SOPT0)
NOTE
RSTPE and NMIE are write-once only on each reset.
Address: 4004_8000h base + 4h offset = 4004_8004h
31
30
29
28
27
26
25
24
23
22
21
20
R
DELAY
19
18
CLKOE
DLYACT
Bit
ADHWT
17
16
BUSREF
W
Reset
POR/
LVD
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
0
0
0
0
0
0
0
0
ACTRG
0
0
RXDFE
0
0
0
0
0
0
0
0
0
0
0
0
0
RSTPE
0
0
0
SWDE
0
0
ACIC
RTCC
Reset
POR/
LVD
RXDCE
W
0
FTMSYNC
TXDME
R
NMIE
1
1
u*
1
u*
1
0
0
* Notes:
• u = Unaffected by reset.
SIM_SOPT0 field descriptions
Field
31–24
DELAY
Description
FTM2 Trigger Delay
Specifies the delay from FTM2 initial or match trigger to ADC hardware trigger when 1 is written to
ADHWT. The 8-bit modulo value allows the delay from 0 to 255 upon the BUSREF clock settings. This is a
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
179
Memory map and register definition
SIM_SOPT0 field descriptions (continued)
Field
Description
one-shot counter that starts ticking when the trigger arrives and stops ticking when the counter value
reaches the modulo value that is defined.
23
DLYACT
FTM2 Trigger Delay Active
This read-only field specifies the status if the FTM2 initial or match delay is active. This field is set when an
FTM2 trigger arrives and the delay counter is ticking. Otherwise, this field will be clear.
0
1
22–20
ADHWT
ADC Hardware Trigger Source
Selects the ADC hardware trigger source. All trigger sources start ADC conversion on rising-edge.
000
001
010
011
100
101
110
111
19
CLKOE
Enables bus clock output on
Enables bus clock output via an optional prescaler.
Bus
Bus divided by 2
Bus divided by 4
Bus divided by 8
Bus divided by 16
Bus divided by 32
Bus divided by 64
Bus divided by 128
UART0_TX Modulation Select
Enables the UART0_TX output modulated by FTM0 channel 0.
0
1
14
FTMSYNC
Bus clock output is disabled on PTH2.
Bus clock output is enabled on PTH2.
BUS Clock Output select
000
001
010
011
100
101
110
111
15
TXDME
RTC overflow as the ADC hardware trigger
FTM0 as the ADC hardware trigger
FTM2 init trigger with 8-bit programmable counter delay
FTM2 match trigger with 8-bit programmable counter delay
PIT channel0 overflow as the ADC hardware trigger
PIT channel1 overflow as the ADC hardware trigger
ACMP0 out as the ADC hardware trigger.
ACMP1 out as the ADC hardware trigger
Bus Clock Output Enable
0
1
18–16
BUSREF
The delay is inactive.
The delay is active.
UART0_TX output is connected to pinout directly.
UART0_TX output is modulated by FTM0 channel 0 before mapped to pinout.
FTM2 Synchronization Select
Generates a PWM synchronization trigger to the FTM2 module if 1 is written to this field.
0
1
No synchronization triggered.
Generates a PWM synchronization trigger to the FTM2 modules.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
180
Freescale Semiconductor, Inc.
Chapter 12 System Integration Module (SIM)
SIM_SOPT0 field descriptions (continued)
Field
13
Reserved
12
RXDCE
Description
This field is reserved.
This read-only field is reserved and always has the value 0.
UART0_RX Capture Select
Enables the UART0_RX to be captured by FTM0 channel 1.
0
1
11
ACIC
Analog Comparator to Input Capture Enable
Connects the output of ACMP0 to FTM1 input channel 0.
0
1
10
RTCC
Allows the Real-time Counter (RTC) overflow to be captured by FTM1 channel 1.
5
ACTRG
Enables the UART0 RxD input to be filtered by ACMP. When this function is enabled, any signal tagged
with ACMP inputs can be regarded UART0.
3
SWDE
RXD0 input signal is connected to UART0 module directly.
RXD0 input signal is filtered by ACMP0, then injected to UART0.
RXD0 input signal is filtered by ACMP1, then injected to UART0.
Reserved.
This field is reserved.
This read-only field is reserved and always has the value 0.
ACMP Trigger FTM2 selection
Selects the two ACMP outputs as the trigger0 input of FTM2
0
1
4
Reserved
RTC overflow is not connected to FTM1 input channel 1.
RTC overflow is connected to FTM1 input channel 1.
UART0 RxD Filter Select
00
01
10
11
7–6
Reserved
ACMP0 output is not connected to FTM1 input channel 0.
ACMP0 output is connected to FTM1 input channel 0.
Real-Time Counter Capture
0
1
9–8
RXDFE
UART0_RX input signal is connected to the UART0 module only.
UART0_RX input signal is connected to the UART0 module and FTM0 channel 1.
ACMP0 out
ACMP1 out
This field is reserved.
This read-only field is reserved and always has the value 0.
Single Wire Debug Port Pin Enable
Enables the PTA4/KBI0_P4/ACMP0_OUT/SWD_DIO pin to function as SWD_DIO, and PTC4/KBI0_P20/
RTC_CLKOUT/FTM1_CH0/ACMP0_IN2/SWD_CLK pin function as SWD_CLK. When clear, the two pins
function as PTA4 and PTC4. This pin defaults to the SWD_DIO and SWD_CLK function following any
MCU reset.
0
1
PTA4/KBI0_P4/ACMP0_OUT/SWD_DIO as PTA4 or ACMP0_OUT function, PTC4/KBI0_P20/
RTC_CLKOUT/FTM1_CH0/ACMP0_IN2/SWD_CLK as PTC4, KBI0_P20, RTC_CLKOUT,
FTM1_CH0, OR ACMP0_IN2 function.
PTA4/KBI0_P4/ACMP0_OUT/SWD_DIO as SWD_DIO function, PTC4/KBI0_P20/RTC_CLKOUT/
FTM1_CH0/ACMP0_IN2/SWD_CLK as SWD_CLK function.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
181
Memory map and register definition
SIM_SOPT0 field descriptions (continued)
Field
Description
2
RSTPE
RESET Pin Enable
This write-once field can be written after any reset. When RSTPE is set, the PTA5/KBI0_P5/IRQ/TCLK0/
RESET pin functions as RESET. When clear, the pin functions as one of its alternative functions. This pin
defaults to RESET following an MCU POR. Other resets will not affect this field. When RSTPE is set, an
internal pullup device on RESET is enabled.
0
1
1
NMIE
PTA5/KBI0_P5/IRQ/TCLK0/RESET pin functions as PTA5/KBI0_P5/IRQ/TCLK0.
PTA5/KBI0_P5/IRQ/TCLK0/RESET pin functions as RESET.
NMI Pin Enable
This write-once field can be written after any reset. When NMIE is set, the PTB4/KBI0_P12/FTM2_CH4/
SPI0_MISO/ACMP1_IN2/NMI pin functions as NMI. When clear, the pin functions as one of its alternative
functions. This pin defaults to NMI following an MCU POR. Other resets will not affect this bit. When NMIE
is set, an internal pullup device on NMI is enabled.
0
1
0
Reserved
PTB4/KBI0_P12/FTM2_CH4/SPI0_MISO/ACMP1_IN2/NMI pin functions as PTB4, KBI0_P12,
FTM2_CH4, SPI0_MISO or ACMP1_IN2.
PTB4/KBI0_P12/FTM2_CH4/SPI0_MISO/ACMP1_IN2/NMI pin functions as NMI.
This field is reserved.
This read-only field is reserved and always has the value 0.
12.2.3 System Options Register (SIM_SOPT1)
NOTE
RSTPE and NMIE are write-only on each reset.
Address: 4004_8000h base + 8h offset = 4004_8008h
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
0
R
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
ACPWTS
0
I2C0OINV
I2C04WEN
W
0
0
0
0
0
R
UARTPWTS
W
Reset
0
0
0
0
0
0
0
0
0
0
0
0
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
182
Freescale Semiconductor, Inc.
Chapter 12 System Integration Module (SIM)
SIM_SOPT1 field descriptions
Field
31–6
Reserved
5–4
UARTPWTS
Description
This field is reserved.
This read-only field is reserved and always has the value 0.
PWT UART RX select
This field select PWTIN3 input signal
00
01
10
11
3
ACPWTS
UART0 RX is connectted to PWTIN3.
UART1 RX is connectted to PWTIN3.
UART2 RX is connectted to PWTIN3.
Reserved.
PWT ACMP_OUT select
This field select PWTIN2 input signal.
0
1
ACMP1_OUT is connectted to PWTIN2.
ACMP0_OUT is connectted to PWTIN2.
2
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
1
I2C0OINV
I2C0 Output Invert
This field controls invertion of the I2C0 output.
NOTE: This bit does not work when I2C0 4-wire interface is disabled (I2C04WEN = 0)
0
1
0
I2C04WEN
Under I2C0 4-wire interface configuration, SDA_OUT and SCL_OUT are not inverted before output
Under I2C0 4-wire interface configuration, SDA_OUT and SCL_OUT are inverted before output
I2C0 4-Wire Interface Enable
This field controls I2C0 4-wire interface configuration.
NOTE: This field works only when SIM_PINSEL0[I2C0PS] is 0.
0
1
I2C0 4-wire interface configuration is disabled.
I2C0 4-wire interface configuration is enabled.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
183
Memory map and register definition
12.2.4 Pin Selection Register 0 (SIM_PINSEL0)
Address: 4004_8000h base + Ch offset = 4004_800Ch
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
0
R
PWTCLKPS FTM2CLKPS FTM1CLKPS FTM0CLKPS
W
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
0
R
W
Reset
0
0
0
0
RTCPS
0
I2C0PS
0
SPI0PS
0
UART0PS
0
FTM0PS0
0
FTM0PS1
0
FTM1PS0
0
FTM1PS1
Reset
0
0
0
0
0
0
0
0
0
IRQPS
0
0
0
0
SIM_PINSEL0 field descriptions
Field
31–30
PWTCLKPS
Description
PWT TCLK Pin Select
Selects the TCLK pinout.
00
01
10
11
29–28
FTM2CLKPS
FTM2 TCLK Pin Select
Selects the TCLK pinout.
00
01
10
11
27–26
FTM1CLKPS
Selects TCLK0 for FTM2 module..
Selects TCLK1 for FTM2 module.
Selects TCLK2 for FTM2 module.
Reserved.
FTM1 TCLK Pin Select
Selects the TCLK pinout.
00
01
10
11
25–24
FTM0CLKPS
Selects TCLK0 for PWT module.
Selects TCLK1 for PWT module.
Selects TCLK2 for PWT module.
Reserved.
Selects TCLK0 for FTM1 module..
Selects TCLK1 for FTM1 module.
Selects TCLK2 for FTM1 module.
Reserved.
FTM0 TCLK Pin Select
Selects the TCLK pinout.
00
01
Selects TCLK0 for FTM0 module..
Selects TCLK1 for FTM0 module.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
184
Freescale Semiconductor, Inc.
Chapter 12 System Integration Module (SIM)
SIM_PINSEL0 field descriptions (continued)
Field
Description
10
11
Selects TCLK2 for FTM0 module.
Reserved.
23–12
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
11
FTM1PS1
FTM1_CH1 Port Pin Select
Selects the FTM1_CH1 channel pinout.
0
1
10
FTM1PS0
FTM1_CH0 Port Pin Select
Selects the FTM1_CH0 channel pinout.
0
1
9
FTM0PS1
Selects the FTM0_CH1 channel pinout.
Selects the FTM0_CH0 channel pinout.
Selects the UART0 pinouts.
Selects the SPI0 Pinouts.
SPI0_SCK, SPI0_MOSI, SPI0_MISO, and SPI0_PCS are mapped on PTB2, PTB3, PTB4, and PTB5.
SPI0_SCK, SPI0_MOSI, SPI0_MISO, and SPI0_PCS are mapped on PTE0, PTE1, PTE2, and PTE3.
I2C0 Port Pin Select
Selects the I2C0 port pins.
0
1
4
RTCPS
UART0_RX and UART0_TX are mapped on PTB0 and PTB1.
UART0_RX and UART0_TX are mapped on PTA2 and PTA3.
SPI0 Pin Select
0
1
5
I2C0PS
FTM0_CH0 channels are mapped on PTA0.
FTM0_CH0 channels are mapped on PTB2.
UART0 Pin Select
0
1
6
SPI0PS
FTM0_CH1 channels are mapped on PTA1.
FTM0_CH1 channels are mapped on PTB3.
FTM0_CH0 Port Pin Select
0
1
7
UART0PS
FTM1_CH0 channels are mapped on PTC4.
FTM1_CH0 channels are mapped on PTH2.
FTM0_CH1 Port Pin Select
0
1
8
FTM0PS0
FTM1_CH1 channels are mapped on PTC5.
FTM1_CH1 channels are mapped on PTE7.
I2C0_SCL and I2C0_SDA are mapped on PTA3 and PTA2, respectively.
I2C0_SCL and I2C0_SDA are mapped on PTB7 and PTB6, respectively.
RTCO Pin Select
Selects the RTCO port pins.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
185
Memory map and register definition
SIM_PINSEL0 field descriptions (continued)
Field
Description
0
1
3
Reserved
RTCO is mapped on PTC4.
RTCO is mapped on PTC5.
This field is reserved.
This read-only field is reserved and always has the value 0.
IRQPS
IRQ Port Pin Select
Selects the IRQ port pins.
000
001
010
011
100
101
110
111
IRQ is mapped on PTA5.
IRQ is mapped on PTI0.
IRQ is mapped on PTI1.
IRQ is mapped on PTI2.
IRQ is mapped on PTI3.
IRQ is mapped on PTI4.
IRQ is mapped on PTI5.
IRQ is mapped on PTI6.
12.2.5 Pin Selection Register 1 (SIM_PINSEL1)
Address: 4004_8000h base + 10h offset = 4004_8010h
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
0
R
16
MSCANPS
Bit
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
R
PWTIN1PS
PWTIN0PS
UART2PS
UART1PS
SPI1PS
I2C1PS
FTM2PS5
FTM2PS4
W
0
0
0
0
0
0
0
0
W
Reset
FTM2PS3
0
0
FTM2PS2
0
FTM2PS1
0
0
0
FTM2PS0
0
0
SIM_PINSEL1 field descriptions
Field
31–17
Reserved
16
MSCANPS
Description
This field is reserved.
This read-only field is reserved and always has the value 0.
MSCAN Pin Select
Selects the MSCAN pinout.
0
1
CAN_TX on PTC7, CAN_RX on PTC6.
CAN_TX on PTE7, CAN_RX on PTH2.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
186
Freescale Semiconductor, Inc.
Chapter 12 System Integration Module (SIM)
SIM_PINSEL1 field descriptions (continued)
Field
15
PWTIN1PS
Description
PWTIN1 Pin Select
Selects the PWTIN1 pinout.
0
1
14
PWTIN0PS
PWTIN0 Pin Select
Selects the PWTIN0 pinout.
0
1
13
UART2PS
Selects the UART2 pinout.
Selects the UART1 pinout.
Selects the SPI1 pinout.
Selects the I2C1 pinout.
Selects the FTM2 Channel 5 pinout.
FTM2 CH5 mapped on PTB5.
FTM2 CH5 mapped on PTG7.
FTM2 Channel4 Pin Select
Selects the FTM2 Channel4 pinout.
0
1
7–6
FTM2PS3
I2C1_SCL on PTE1, I2C1_SDA on PTE0.
I2C1_SCL on PTH4, I2C1_SDA on PTH3.
FTM2 Channel 5 Pin Select
0
1
8
FTM2PS4
SPI1_SCK, SPI1_MOSI, SPI1_MISO, and SPI1_PCS are mapped on PTD0, PTD1, PTD2, and PTD3.
SPI1_SCK, SPI1_MOSI, SPI1_MISO, and SPI1_PCS are mapped on PTG4, PTG5, PTG6, and
PTG7.
I2C1 Pin Select
0
1
9
FTM2PS5
UART1_TX on PTC7, UART1_RX on PTC6.
UART1_TX on PTF3, UART1_RX on PTF2.
SPI1 Pin Select
0
1
10
I2C1PS
UART2_TX on PTD7, UART2_RX on PTD6.
UART2_TX on PTI1, UART2_RX on PTI0.
UART1 Pin Select
0
1
11
SPI1PS
PWTIN0 on PTD5.
PWTIN0 on PTE2.
UART2 Pin Select
0
1
12
UART1PS
PWTIN1 on PTB0.
PWTIN1 on PTH7.
FTM2 CH4 mapped on PTB4.
FTM2 CH4 mapped on PTG6.
FTM2 Channel 3 Pin Select
Selects the FTM2 Channel 3 pinout.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
187
Memory map and register definition
SIM_PINSEL1 field descriptions (continued)
Field
Description
00
01
10
11
5–4
FTM2PS2
FTM2 CH3 mapped on PTC3.
FTM2 CH3 mapped on PTD1.
FTM2 CH3 mapped on PTG5.
Reserved.
FTM2 Channel 2 Pin Select
Selects the FTM2 Channel 2 pinout.
00
01
10
11
3–2
FTM2PS1
FTM2 CH2 mapped on PTC2.
FTM2 CH2 mapped on PTD0.
FTM2 CH2 mapped on PTG4.
Reserved.
FTM2 Channel 1 Pin Select
Selects the FTM2 Channel 1 pinout.
00
01
10
11
FTM2PS0
FTM2 CH1 mapped on PTC1.
FTM2 CH1 mapped on PTH1.
FTM2 CH1 mapped on PTF1.
Reserved.
FTM2 Channel 0 Pin Select
Selects the FTM2 Channel 0 pinout.
00
01
10
11
FTM2 CH0 mapped on PTC0.
FTM2 CH0 mapped on PTH0.
FTM2 CH0 mapped on PTF0.
Reserved.
12.2.6 System Clock Gating Control Register (SIM_SCGC)
Address: 4004_8000h base + 14h offset = 4004_8014h
Reset
0
0
0
0
0
Bit
15
14
13
12
11
MSCAN
Reset
0
0
SWD
1
1
0
21
20
19
18
17
16
SPI0
I2C1
I2C0
KBI0
SPI1
0
0
0
0
0
0
0
0
0
0
0
10
9
8
7
6
5
4
3
2
1
0
PIT
RTC
0
0
0
0
CRC
0
22
KBI1
IRQ
FLASH
W
23
UART0
ADC
0
24
0
W
R
25
UART1
0
26
0
0
0
0
FTM0
27
UART2
28
FTM1
29
ACMP0
30
ACMP1
R
31
FTM2
Bit
PWT
0
0
0
0
0
0
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
188
Freescale Semiconductor, Inc.
Chapter 12 System Integration Module (SIM)
SIM_SCGC field descriptions
Field
31
ACMP1
Description
ACMP1 Clock Gate Control
Controls the clock gate to the ACMP1 module.
0
1
30
ACMP0
ACMP0 Clock Gate Control
Controls the clock gate to the ACMP0 module.
0
1
29
ADC
27
IRQ
Controls the clock gate to the ADC module.
25
KBI1
IRQ Clock Gate Control
Controls the clock gate to the IRQ module.
KBI1 Clock Gate Control
Controls the clock gate to the KBI1 module.
22
UART2
Controls the clock gate to the KBI0 module.
Bus clock to the KBI0 module is disabled.
Bus clock to the KBI0 module is enabled.
This field is reserved.
This read-only field is reserved and always has the value 0.
UART2 Clock Gate Control
Controls the clock gate to the UART2 module.
0
1
21
UART1
Bus clock to the KBI1 module is disabled.
Bus clock to the KBI1 module is enabled.
KBI0 Clock Gate Control
0
1
23
Reserved
Bus clock to the IRQ module is disabled.
Bus clock to the IRQ module is enabled.
This field is reserved.
This read-only field is reserved and always has the value 0.
0
1
24
KBI0
Bus clock to the ADC module is disabled.
Bus clock to the ADC module is enabled.
This field is reserved.
This read-only field is reserved and always has the value 0.
0
1
26
Reserved
Bus clock to the ACMP0 module is disabled.
Bus clock to the ACMP0 module is enabled.
ADC Clock Gate Control
0
1
28
Reserved
Bus clock to the ACMP1 module is disabled.
Bus clock to the ACMP1 module is enabled.
Bus clock to the UART2 module is disabled.
Bus clock to the UART2 module is enabled.
UART1 Clock Gate Control
Ccontrols the clock gate to the UART1 module.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
189
Memory map and register definition
SIM_SCGC field descriptions (continued)
Field
Description
0
1
20
UART0
UART0 Clock Gate Control
Controls the clock gate to the UART0 module.
0
1
19
SPI1
Controls the clock gate to the SPI1 module.
Controls the clock gate to the SPI0 module.
Controls the clock gate to the I2C1 module.
Controls the clock gate to the I2C0 module.
13
SWD
Controls the clock gate to the MSCAN module.
Bus clock to the MSCAN module is disabled.
Bus clock to the MSCAN module is enabled.
This field is reserved.
This read-only field is reserved and always has the value 0.
SWD (single wire debugger) Clock Gate Control
Controls the clock gate to the SWD module.
0
1
12
FLASH
Bus clock to the I2C0 module is disabled.
Bus clock to the I2C0 module is enabled.
MSCAN Clock Gate Control
0
1
14
Reserved
Bus clock to the I2C1 module is disabled.
Bus clock to the I2C1 module is enabled.
I2C0 Clock Gate Control
0
1
15
MSCAN
Bus clock to the SPI0 module is disabled.
Bus clock to the SPI0 module is enabled.
I2C1 Clock Gate Control
0
1
16
I2C0
Bus clock to the SPI1 module is disabled.
Bus clock to the SPI1 module is enabled.
SPI0 Clock Gate Control
0
1
17
I2C1
Bus clock to the UART0 module is disabled.
Bus clock to the UART0 module is enabled.
SPI1 Clock Gate Control
0
1
18
SPI0
Bus clock to the UART1 module is disabled.
Bus clock to the UART1 module is enabled.
Bus clock to the SWD module is disabled.
Bus clock to the SWD module is enabled.
Flash Clock Gate Control
Controls the clock gate to the flash module.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
190
Freescale Semiconductor, Inc.
Chapter 12 System Integration Module (SIM)
SIM_SCGC field descriptions (continued)
Field
Description
0
1
11
Reserved
10
CRC
This field is reserved.
This read-only field is reserved and always has the value 0.
CRC Clock Gate Control
Controls the clock gate to the CRC module.
0
1
9–8
Reserved
7
FTM2
FTM2 Clock Gate Control
Controls the clock gate to the FTM2 module.
Controls the clock gate to the FTM1 module.
Controls the clock gate to the FTM0 module.
1
PIT
Controls the clock gate to the PWT module.
Timer clock to the PWT module is disabled.
Timer clock to the PWT module is enabled.
This field is reserved.
This read-only field is reserved and always has the value 0.
PIT Clock Gate Control
Controls the clock gate to the PIT module.
0
1
0
RTC
Bus clock to the FTM0 module is disabled.
Bus clock to the FTM0 module is enabled.
PWT Clock Gate Control
0
1
3–2
Reserved
Bus clock to the FTM1 module is disabled.
Bus clock to the FTM1 module is enabled.
FTM0 Clock Gate Control
0
1
4
PWT
Bus clock to the FTM2 module is disabled.
Bus clock to the FTM2 module is enabled.
FTM1 Clock Gate Control
0
1
5
FTM0
Bus clock to the CRC module is disabled.
Bus clock to the CRC module is enabled.
This field is reserved.
This read-only field is reserved and always has the value 0.
0
1
6
FTM1
Bus clock to the flash module is disabled.
Bus clock to the flash module is enabled.
Bus clock to the PIT module is disabled.
Bus clock to the PIT module is enabled.
RTC Clock Gate Control
Controls the clock gate to the RTC module.
0
1
Bus clock to the RTC module is disabled.
Bus clock to the RTC module is enabled.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
191
Memory map and register definition
12.2.7 Universally Unique Identifier Low Register (SIM_UUIDL)
The read-only SIM_UUIDL register contains a series of number to identify the unique
device in the family.
Address: 4004_8000h base + 18h offset = 4004_8018h
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
ID[31:0]
R
W
Reset
x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x*
* Notes:
• x = Undefined at reset.
SIM_UUIDL field descriptions
Field
Description
ID[31:0]
Universally Unique Identifier
12.2.8 Universally Unique Identifier Middle Low Register
(SIM_UUIDML)
The read-only SIM_UUIDML register contains a series of number to identify the unique
device in the family.
Address: 4004_8000h base + 1Ch offset = 4004_801Ch
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
ID[63:32]
R
W
Reset
x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x*
* Notes:
• x = Undefined at reset.
SIM_UUIDML field descriptions
Field
ID[63:32]
Description
Universally Unique Identifier
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
192
Freescale Semiconductor, Inc.
Chapter 12 System Integration Module (SIM)
12.2.9 Universally Unique Identifier Middle High Register
(SIM_UUIDMH)
The read-only SIM_UUIDMH register contains a series of number to identify the unique
device in the family.
Address: 4004_8000h base + 20h offset = 4004_8020h
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
0
R
9
8
7
6
5
4
3
2
1
0
ID[80:64]
W
Reset
x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x* x*
* Notes:
• x = Undefined at reset.
SIM_UUIDMH field descriptions
Field
Description
31–16
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
ID[80:64]
Universally Unique Identifier
12.2.10 Clock Divider Register (SIM_CLKDIV)
This register sets the divide value for the clock.
NOTE
Carefully confiugre the OUTDIV1 and OUTDIV2 to avoid bus
clock frequency high than 24 MHz.
Address: 4004_8000h base + 24h offset = 4004_8024h
30
29
28
27
0
R
26
25
0
OUTDIV1
W
Reset
POR/
LVD
0
0
0
0
u*
0
u*
0
0
0
0
0
24
23
0
0
u*
0
22
21
0
0
0
0
0
20
19
18
0
0
u*
0
17
16
0
0
0
0
0
OUTDIV3
31
OUTDIV2
Bit
0
0
0
0
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
193
Functional description
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
R
W
Reset
POR/
LVD
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
* Notes:
• u = Unaffected by reset.
SIM_CLKDIV field descriptions
Field
Description
31–30
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
29–28
OUTDIV1
Clock 1 output divider value
This field sets the divide value for the core/system clock,.
00
01
10
11
Same as ICSOUTCLK.
ICSOUTCLK divides by 2.
ICSOUTCLK divides by 3.
ICSOUTCLK divides by 4.
27–25
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
24
OUTDIV2
Clock 2 output divider value
This field sets the divide value for the bus/FLASH, follow OUTDIV1.
0
1
Not divided from divider1.
Divide by 2 from divider1.
23–21
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
20
OUTDIV3
Clock 3 output divider value
This field sets the divide value for the timers(FTM0, FTM1, FTM2,PWT).
0
1
Reserved
Same as ICSOUTCLK.
ICSOUTCLK divides by 2.
This field is reserved.
This read-only field is reserved and always has the value 0.
12.3 Functional description
See Introduction section.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
194
Freescale Semiconductor, Inc.
Chapter 13
Power Management Controller (PMC)
13.1 Introduction
This chapter describes the functionality of the individual modules in the chip’s lowpower modes and the operation of Power Management Controller module.
13.2 Low voltage detect (LVD) system
This device includes a system to protect against low voltage conditions in order to protect
memory contents and control MCU system states during supply voltage variations. This
system consists of a power-on reset (POR) circuit and an LVD circuit with a user
selectable trip voltage, either high (VLVDH) or low (VLVDL). The LVD circuit is enabled
when SPMSC1[LVDE] is set and the trip voltage is selected by SPMSC2[LVDV]. The
LVD is disabled upon entering the Stop mode unless SPMSC1[LVDSE] is set. If
SPMSC1[LVDSE] and SPMSC1[LVDE] are both set, the current consumption will be
greater in Stop mode with the LVD system enabled.
The following figure presents the block diagram of the low-voltage detect (LVD) system.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
195
Low voltage detect (LVD) system
vDD
LVDV:LVWV
R1
LVD0
-
LVD1
LVD
+
LVW0
LVW1
LVW2
-
LVW3
LVW
+
vBG
Bandgap
R7
vss
Figure 13-1. Low voltage detect (LVD) block diagram
13.2.1 Power-on reset (POR) operation
When power is initially applied to the MCU, or when the supply voltage drops below the
VPOR level, the POR circuit will cause a reset condition. As the supply voltage rises, the
LVD circuit will hold the chip in reset until the supply has risen above the VLVDL level.
Both the SIM_SRSID[POR] and SIM_SRSID[LVD] are set following a POR.
13.2.2 LVD reset operation
The LVD can be configured to generate a reset upon detection of a low-voltage condition
by setting SPMSC1[LVDRE] to 1. After an LVD reset has occurred, the LVD system
will hold the MCU in reset until the supply voltage has risen above the level determined
by LVDV. SIM_SRSID[LVD] is set following either an LVD reset or POR.
13.2.3 LVD enabled in Stop mode
The LVD system is capable of generating a reset when the supply voltage drops below
the LVD voltage. If the LVD is enabled in Stop (both SPMSC1[LVDE] and
SPMSC1[LVDSE] set to 1) at the time the CPU executes a STOP instruction, then the
voltage regulator remains active during Stop mode.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
196
Freescale Semiconductor, Inc.
Chapter 13 Power Management Controller (PMC)
13.2.4 Low-voltage warning (LVW)
The LVD system has a low voltage warning flag to indicate that the supply voltage is
approaching the LVW voltage. When a low voltage condition is detected and the LVD
circuit is configured for interrupt operation (SPMSC1[LVDE] set, SPMSC1[LVWIE]
set), SPMSC1[LVWF] will be set and LVW interrupt will occur. There are four userselectable trip voltages for the LVW upon each LVDV configuration. The trip voltage is
selected by SPMSC2[LVWV].
13.3 Bandgap reference
This device includes an on-chip bandgap reference (≈1.2 V) connected to the ADC
channel. The bandgap reference voltage will not drop under the full operating voltage
even when the operating voltage is falling. This reference voltage acts as an ideal
reference voltage for accurate measurements.
13.4 Memory map and register descriptions
PMC memory map
Absolute
address
(hex)
Register name
Width
Access
(in bits)
Reset value
Section/
page
4007_D000
System Power Management Status and Control 1 Register
(PMC_SPMSC1)
8
R/W
1Ch
13.4.1/198
4007_D001
System Power Management Status and Control 2 Register
(PMC_SPMSC2)
8
R/W
00h
13.4.2/199
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
197
Memory map and register descriptions
13.4.1 System Power Management Status and Control 1 Register
(PMC_SPMSC1)
This high-page register contains status and control bits to support the low-voltage
detection function, and to enable the bandgap voltage reference for use by the ADC
module. This register must be written during the user's reset initialization program to set
the desired controls, even if the desired settings are the same as the reset settings.
Address: 4007_D000h base + 0h offset = 4007_D000h
Bit
Read
7
6
LVWF
0
Write
Reset
LVWACK
0
5
4
3
2
LVWIE
LVDRE
LVDSE
LVDE
0
1
1
1
0
1
0
0
0
BGBE
0
PMC_SPMSC1 field descriptions
Field
7
LVWF
Description
Low-Voltage Warning Flag
Indicates the low-voltage warning status.
NOTE: LVWF will be set in the case when VSupply transitions below the trip point or after reset and VSupply
is already below VLVW. LVWF may be 1 after power-on-reset, therefore, to use LVW interrupt
function, before enabling LVWIE, LVWF must be cleared by writing LVWACK first.
0
1
6
LVWACK
5
LVWIE
Low-Voltage Warning Acknowledge
If LVWF = 1, a low-voltage condition has occurred. To acknowledge this low-voltage warning, write 1 to
LVWACK, which automatically clears LVWF to 0 if the low-voltage warning is no longer present.
Low-Voltage Warning Interrupt Enable
Enables hardware interrupt requests for LVWF.
0
1
4
LVDRE
Low-voltage warning is not present.
Low-voltage warning is present or was present.
Hardware interrupt is disabled (use polling).
Requests a hardware interrupt when LVWF = 1.
Low-Voltage Detect Reset Enable
This write-once bit enables LVD events to generate a hardware reset (provided LVDE = 1).
NOTE: This field can be written only one time after reset. Additional writes are ignored.
If LVDRE = 0, use LVW to monitor status because no flag was assert.
0
1
3
LVDSE
LVD events do not generate hardware resets.
Forces an MCU reset when an enabled low-voltage detect event occurs.
Low-Voltage Detect Stop Enable
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
198
Freescale Semiconductor, Inc.
Chapter 13 Power Management Controller (PMC)
PMC_SPMSC1 field descriptions (continued)
Field
Description
Provided LVDE = 1, this read/write field determines whether the low-voltage detect function operates
when the MCU is in Stop mode.
0
1
2
LVDE
Low-voltage detect is disabled during Stop mode.
Low-voltage detect is enabled during Stop mode.
Low-Voltage Detect Enable
This write-once bit enables low-voltage detect logic and qualifies the operation of other fields in this
register.
NOTE: This field can be written only one time after reset. Additional writes are ignored.
0
1
1
Reserved
0
BGBE
LVD logic is disabled.
LVD logic is enabled.
This field is reserved.
Bandgap Buffer Enable
Enables an internal buffer for the bandgap voltage reference for use by the ADC module on one of its
internal channels or bandgap selected as ACMP's reference.
0
1
Bandgap buffer is disabled.
Bandgap buffer is enabled.
13.4.2 System Power Management Status and Control 2 Register
(PMC_SPMSC2)
This register is used to report the status of the low-voltage warning function, and to
configure the Stop mode behavior of the MCU. This register should be written during the
user's reset initialization program to set the desired controls, even if the desired settings
are the same as the reset settings.
Address: 4007_D000h base + 1h offset = 4007_D001h
Bit
7
Read
Write
Reset
0
6
LVDV
0
0
5
4
3
2
LVWV
0
1
0
0
0
0
0
0
0
PMC_SPMSC2 field descriptions
Field
7
Reserved
6
LVDV
Description
This field is reserved.
This read-only field is reserved and always has the value 0.
Low-Voltage Detect Voltage Select
This write-once bit selects the low-voltage detect (LVD) trip point setting. See data sheet for details.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
199
Memory map and register descriptions
PMC_SPMSC2 field descriptions (continued)
Field
Description
0
1
5–4
LVWV
Low-Voltage Warning Voltage Select
Selects the low-voltage warning (LVW) trip point voltage. See data sheet for details.
00
01
10
11
Reserved
Low trip point is selected (VLVD = VLVDL).
High trip point is selected (VLVD = VLVDH).
Low trip point is selected (VLVW = VLVW1).
Middle 1 trip point is selected (VLVW = VLVW2).
Middle 2 trip point is selected (VLVW = VLVW3).
High trip point is selected (VLVW = VLVW4).
This field is reserved.
This read-only field is reserved and always has the value 0.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
200
Freescale Semiconductor, Inc.
Chapter 14
Miscellaneous Control Module (MCM)
14.1 Introduction
NOTE
For the chip-specific implementation details of this module's
instances, see the chip configuration information.
The Miscellaneous Control Module (MCM) provides a myriad of miscellaneous control
functions.
14.1.1 Features
The MCM includes the following features:
• Program-visible information on the platform configuration
• Flash controller speculation buffer and cache configurations
14.2 Memory map/register descriptions
The memory map and register descriptions found here describe the registers using byte
addresses. The registers can be written only when in supervisor mode.
MCM memory map
Absolute
address
(hex)
Register name
Width
Access
(in bits)
Reset value
Section/
page
F000_3008
Crossbar Switch (AXBS) Slave Configuration
(MCM_PLASC)
16
R
0007h
14.2.1/202
F000_300A
Crossbar Switch (AXBS) Master Configuration
(MCM_PLAMC)
16
R
0001h
14.2.2/202
32
R/W
0000_0800h
14.2.3/203
F000_300C Platform Control Register (MCM_PLACR)
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
201
Memory map/register descriptions
14.2.1 Crossbar Switch (AXBS) Slave Configuration (MCM_PLASC)
PLASC is a 16-bit read-only register identifying the presence/absence of bus slave
connections to the device’s crossbar switch.
Address: F000_3000h base + 8h offset = F000_3008h
Bit
15
14
13
12
Read
11
10
9
8
7
6
5
4
0
3
2
1
0
0
1
1
1
ASC
Write
Reset
0
0
0
0
0
0
0
0
0
0
0
0
MCM_PLASC field descriptions
Field
Description
15–8
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
ASC
Each bit in the ASC field indicates whether there is a corresponding connection to the crossbar switch's
slave input port.
0
1
A bus slave connection to AXBS input port n is absent.
A bus slave connection to AXBS input port n is present.
14.2.2 Crossbar Switch (AXBS) Master Configuration (MCM_PLAMC)
PLAMC is a 16-bit read-only register identifying the presence/absence of bus master
connections to the device's crossbar switch.
Address: F000_3000h base + Ah offset = F000_300Ah
Bit
15
14
13
12
Read
11
10
9
8
7
6
5
4
0
3
2
1
0
0
0
0
1
AMC
Write
Reset
0
0
0
0
0
0
0
0
0
0
0
0
MCM_PLAMC field descriptions
Field
15–8
Reserved
AMC
Description
This field is reserved.
This read-only field is reserved and always has the value 0.
Each bit in the AMC field indicates whether there is a corresponding connection to the AXBS master input
port.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
202
Freescale Semiconductor, Inc.
Chapter 14 Miscellaneous Control Module (MCM)
MCM_PLAMC field descriptions (continued)
Field
Description
0
1
A bus master connection to AXBS input port n is absent
A bus master connection to AXBS input port n is present
14.2.3 Platform Control Register (MCM_PLACR)
The speculation buffer and cache in the flash memory controller is configurable via
PLACR[15:10 ].
The speculation buffer is enabled only for instructions after reset. It is possible to have
these states for the speculation buffer:
DFCS
EFDS
Description
0
0
Speculation buffer is on for instruction
and off for data.
0
1
Speculation buffer is on for instruction
and on for data.
1
X
Speculation buffer is off.
The cache in flash controller is enabled and caching both instruction and data type fetches
after reset. It is possible to have these states for the cache:
DFCC
DFCIC
DFCDA
Description
0
0
0
Cache is on for both
instruction and data.
0
0
1
Cache is on for instruction
and off for data.
0
1
0
Cache is off for instruction
and on for data.
0
1
1
Cache is off for both
instruction and data.
1
X
X
Cache is off.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
203
Memory map/register descriptions
Address: F000_3000h base + Ch offset = F000_300Ch
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
0
R
ESFC
W
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
0
0
0
0
0
DFCS
EFDS
DFCC
DFCIC
DFCDA
0
0
0
0
1
W
Reset
0
CFCC
0
R
0
0
0
0
0
0
MCM_PLACR field descriptions
Field
31–17
Reserved
16
ESFC
Description
This field is reserved.
This read-only field is reserved and always has the value 0.
Enable Stalling Flash Controller
Enables stalling flash controller when flash is busy.
When software needs to access the flash memory while a flash memory resource is being manipulated by
a flash command, software can enable a stall mechanism to avoid a read collision. The stall mechanism
allows software to execute code from the same block on which flash operations are being performed.
However, software must ensure the sector the flash operations are being performed on is not the same
sector from which the code is executing.
ESFC enables the stall mechanism. This bit must be set only just before the flash operation is executed
and must be cleared when the operation completes.
0
1
15
DFCS
Disable Flash Controller Speculation
Disables flash controller speculation.
0
1
14
EFDS
Disable stalling flash controller when flash is busy.
Enable stalling flash controller when flash is busy.
Enable flash controller speculation.
Disable flash controller speculation.
Enable Flash Data Speculation
Enables flash data speculation.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
204
Freescale Semiconductor, Inc.
Chapter 14 Miscellaneous Control Module (MCM)
MCM_PLACR field descriptions (continued)
Field
Description
0
1
13
DFCC
Disable Flash Controller Cache
Disables flash controller cache.
0
1
12
DFCIC
Disables flash controller instruction caching.
Reserved
Enable flash controller instruction caching.
Disable flash controller instruction caching.
Disable Flash Controller Data Caching
Disables flash controller data caching.
0
1
10
CFCC
Enable flash controller cache.
Disable flash controller cache.
Disable Flash Controller Instruction Caching
0
1
11
DFCDA
Disable flash data speculation.
Enable flash data speculation.
Enable flash controller data caching
Disable flash controller data caching.
Clear Flash Controller Cache
Writing a 1 to this field clears the cache. Writing a 0 to this field is ignored. This field always reads as 0.
This field is reserved.
This read-only field is reserved and always has the value 0.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
205
Memory map/register descriptions
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
206
Freescale Semiconductor, Inc.
Chapter 15
Peripheral Bridge (AIPS-Lite)
15.1 Introduction
NOTE
For the chip-specific implementation details of this module's
instances, see the chip configuration information.
The peripheral bridge converts the crossbar switch interface to an interface that can
access most of the slave peripherals on this chip.
The peripheral bridge occupies 64 MB of the address space, which is divided into
peripheral slots of 4 KB. (It might be possible that all the peripheral slots are not used.
See the memory map chapter for details on slot assignments.) The bridge includes
separate clock enable inputs for each of the slots to accommodate slower peripherals.
15.1.1 Features
Key features of the peripheral bridge are:
• Supports peripheral slots with 8-, 16-, and 32-bit datapath width
15.1.2 General operation
The slave devices connected to the peripheral bridge are modules which contain a
programming model of control and status registers. The system masters read and write
these registers through the peripheral bridge. The peripheral bridge performs a bus
protocol conversion of the master transactions and generates the following as inputs to
the peripherals:
• Module enables
• Module addresses
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
207
Functional description
• Transfer attributes
• Byte enables
• Write data
The peripheral bridge selects and captures read data from the peripheral interface and
returns it to the crossbar switch.
The register maps of the peripherals are located on 4-KB boundaries. Each peripheral is
allocated one or more 4-KB block(s) of the memory map.
The AIPS-Lite module uses the data width of accessed peripheral to perform proper data
byte lane routing; bus decomposition (bus sizing) is performed when the access size is
larger than the peripheral's data width.
15.2 Functional description
The peripheral bridge functions as a bus protocol translator between the crossbar switch
and the slave peripheral bus.
The peripheral bridge manages all transactions destined for the attached slave devices and
generates select signals for modules on the peripheral bus by decoding accesses within
the attached address space.
15.2.1 Access support
All combinations of access size and peripheral data port width are supported. An access
that is larger than the target peripheral's data width will be decomposed to multiple,
smaller accesses. Bus decomposition is terminated by a transfer error caused by an access
to an empty register area.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
208
Freescale Semiconductor, Inc.
Chapter 16
Watchdog Timer (WDOG)
16.1 Introduction
The Watchdog Timer (WDOG) module is an independent timer that is available for
system use. It provides a safety feature to ensure that software is executing as planned
and that the CPU is not stuck in an infinite loop or executing unintended code. If the
WDOG module is not serviced (refreshed) within a certain period, it resets the MCU.
16.1.1 Features
Features of the WDOG module include:
• Configurable clock source inputs independent from the bus clock
• Internal 32 kHz RC oscillator
• Internal 1 kHz RC oscillator
• External clock source
• Programmable timeout period
• Programmable 16-bit timeout value
• Optional fixed 256 clock prescaler when longer timeout periods are needed
• Robust write sequence for counter refresh
• Refresh sequence of writing 0x02A6 and then 0x80B4 within 16 bus clocks
• Window mode option for the refresh mechanism
• Programmable 16-bit window value
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
209
Introduction
• Provides robust check that program flow is faster than expected
• Early refresh attempts trigger a reset.
• Optional timeout interrupt to allow post-processing diagnostics
• Interrupt request to CPU with interrupt vector for an interrupt service routine
(ISR)
• Forced reset occurs 128 bus clocks after the interrupt vector fetch.
• Configuration bits are write-once-after-reset to ensure watchdog configuration cannot
be mistakenly altered.
• Robust write sequence for unlocking write-once configuration bits
• Unlock sequence of writing 0x20C5 and then 0x28D9 within 16 bus clocks for
allowing updates to write-once configuration bits
• Software must make updates within 128 bus clocks after unlocking and before
WDOG closing unlock window.
16.1.2 Block diagram
The following figure provides a block diagram of the WDOG module.
16-bit Timeout Value Register
0x02A6
0x80B4
Refresh Sequence
Write Control
32K CLK
MUX
1K CLK
Compare Logic
Counter
Overflow
16-bit Counter Register
Counter
Reset
MUX
BUS CLK
EXT CLK
Control
Logic
128 Bus
Clock Delay
MUX
Backup Reset
CPU Reset
256
Compare Logic
EN
UPDATE
16-bit Window Register
Window
Protect
IRQ Interrupt
128 Bus Cycle
Disable Protect
0x20C5 Control Status
0x28D9 Bit Write Control
CLK
PRES WIN
INT
Figure 16-1. WDOG block diagram
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
210
Freescale Semiconductor, Inc.
Chapter 16 Watchdog Timer (WDOG)
16.2 Memory map and register definition
NOTE
If the device uses half-word to access WDOG_CNT,
WDOG_TOVAL and WDOG_WIN, the transposed 16-bit
bytes must follow the format of LowByte:HighByte. So 8-bit R/
W is preferred.
WDOG memory map
Absolute
address
(hex)
Width
Access
(in bits)
Register name
Reset value
Section/
page
4005_2000
Watchdog Control and Status Register 1 (WDOG_CS1)
8
R/W
80h
16.2.1/211
4005_2001
Watchdog Control and Status Register 2 (WDOG_CS2)
8
R/W
01h
16.2.2/213
4005_2002
Watchdog Counter Register: High (WDOG_CNTH)
8
R
00h
16.2.3/214
4005_2003
Watchdog Counter Register: Low (WDOG_CNTL)
8
R
00h
16.2.4/214
4005_2004
Watchdog Timeout Value Register: High (WDOG_TOVALH)
8
R/W
00h
16.2.5/215
4005_2005
Watchdog Timeout Value Register: Low (WDOG_TOVALL)
8
R/W
04h
16.2.6/215
4005_2006
Watchdog Window Register: High (WDOG_WINH)
8
R/W
00h
16.2.7/216
4005_2007
Watchdog Window Register: Low (WDOG_WINL)
8
R/W
00h
16.2.8/216
16.2.1 Watchdog Control and Status Register 1 (WDOG_CS1)
This section describes the function of Watchdog Control and Status Register 1.
NOTE
TST is cleared (0:0) on POR only. Any other reset does not
affect the value of this field.
Address: 4005_2000h base + 0h offset = 4005_2000h
Bit
Read
Write
Reset
7
6
5
EN
INT
UPDATE
1
0
0
4
3
TST
0
0
2
1
0
DBG
WAIT
STOP
0
0
0
WDOG_CS1 field descriptions
Field
7
EN
Description
Watchdog Enable
This write-once bit enables the watchdog counter to start counting.
0
1
Watchdog disabled.
Watchdog enabled.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
211
Memory map and register definition
WDOG_CS1 field descriptions (continued)
Field
6
INT
Description
Watchdog Interrupt
This write-once bit configures the watchdog to generate an interrupt request upon a reset-triggering event
(timeout or illegal write to the watchdog), prior to forcing a reset. After the interrupt vector fetch, the reset
occurs after a delay of 128 bus clocks.
0
1
5
UPDATE
Allow updates
This write-once bit allows software to reconfigure the watchdog without a reset.
0
1
4–3
TST
Watchdog interrupts are disabled. Watchdog resets are not delayed.
Watchdog interrupts are enabled. Watchdog resets are delayed by 128 bus clocks.
Updates not allowed. After the initial configuration, the watchdog cannot be later modified without
forcing a reset.
Updates allowed. Software can modify the watchdog configuration registers within 128 bus clocks
after performing the unlock write sequence.
Watchdog Test
Enables the fast test mode. The test mode allows software to exercise all bits of the counter to
demonstrate that the watchdog is functioning properly. See the Fast testing of the watchdog section.
This write-once field is cleared (0:0) on POR only. Any other reset does not affect the value of this field.
00
01
10
11
2
DBG
Debug Enable
This write-once bit enables the watchdog to operate when the chip is in debug mode.
0
1
1
WAIT
Watchdog disabled in chip debug mode.
Watchdog enabled in chip debug mode.
Wait Enable
This write-once bit enables the watchdog to operate when the chip is in wait mode.
0
1
0
STOP
Watchdog test mode disabled.
Watchdog user mode enabled. (Watchdog test mode disabled.) After testing the watchdog, software
should use this setting to indicate that the watchdog is functioning normally in user mode.
Watchdog test mode enabled, only the low byte is used. WDOG_CNTL is compared with
WDOG_TOVALL.
Watchdog test mode enabled, only the high byte is used. WDOG_CNTH is compared with
WDOG_TOVALH.
Watchdog disabled in chip wait mode.
Watchdog enabled in chip wait mode.
Stop Enable
This write-once bit enables the watchdog to operate when the chip is in stop mode.
0
1
Watchdog disabled in chip stop mode.
Watchdog enabled in chip stop mode.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
212
Freescale Semiconductor, Inc.
Chapter 16 Watchdog Timer (WDOG)
16.2.2 Watchdog Control and Status Register 2 (WDOG_CS2)
This section describes the function of the watchdog control and status register 2.
Address: 4005_2000h base + 1h offset = 4005_2001h
Bit
Read
Write
Reset
7
WIN
6
5
FLG
0
w1c
0
0
0
4
3
2
1
0
PRES
0
0
0
CLK
0
0
1
WDOG_CS2 field descriptions
Field
7
WIN
Description
Watchdog Window
This write-once bit enables window mode. See the Window mode section.
0
1
6
FLG
Watchdog Interrupt Flag
This bit is an interrupt indicator when INT is set in control and status register 1. Write 1 to clear it.
0
1
5
Reserved
4
PRES
CLK
No interrupt occurred.
An interrupt occurred.
This field is reserved.
This read-only field is reserved and always has the value 0.
Watchdog Prescalar
This write-once bit enables a fixed 256 pre-scaling of watchdog counter reference clock. (The block
diagram shows this clock divider option.)
0
1
3–2
Reserved
Window mode disabled.
Window mode enabled.
256 prescalar disabled.
256 prescalar enabled.
This field is reserved.
This read-only field is reserved and always has the value 0.
Watchdog Clock
This write-once field indicates the clock source that feeds the watchdog counter. See the Clock source
section.
00
01
10
11
Bus clock.
1 kHz internal low-power oscillator (LPOCLK).
32 kHz internal oscillator (ICSIRCLK).
External clock source.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
213
Memory map and register definition
16.2.3 Watchdog Counter Register: High (WDOG_CNTH)
This section describes the watchdog counter registers: high (CNTH) and low (CNTL)
combined.
The watchdog counter registers CNTH and CNTL provide access to the value of the freerunning watchdog counter. Software can read the counter registers at any time.
Software cannot write directly to the watchdog counter; however, two write sequences to
these registers have special functions:
1. The refresh sequence resets the watchdog counter to 0x0000. See the Refreshing the
Watchdog section.
2. The unlock sequence allows the watchdog to be reconfigured without forcing a reset
(when WDOG_CS1[UPDATE] = 1). See the Example code: Reconfiguring the
Watchdog section.
NOTE
All other writes to these registers are illegal and force a reset.
Address: 4005_2000h base + 2h offset = 4005_2002h
Bit
7
6
5
4
Read
3
2
1
0
0
0
0
0
CNTHIGH
Write
Reset
0
0
0
0
WDOG_CNTH field descriptions
Field
CNTHIGH
Description
High byte of the Watchdog Counter
16.2.4 Watchdog Counter Register: Low (WDOG_CNTL)
See the description of the WDOG_CNTH register.
Address: 4005_2000h base + 3h offset = 4005_2003h
Bit
7
6
5
4
Read
3
2
1
0
0
0
0
0
CNTLOW
Write
Reset
0
0
0
0
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
214
Freescale Semiconductor, Inc.
Chapter 16 Watchdog Timer (WDOG)
WDOG_CNTL field descriptions
Field
CNTLOW
Description
Low byte of the Watchdog Counter
16.2.5 Watchdog Timeout Value Register: High (WDOG_TOVALH)
This section describes the watchdog timeout value registers: high (WDOG_TOVALH)
and low (WDOG_TOVALL) combined. WDOG_TOVALH and WDOG_TOVALL
contains the 16-bit value used to set the timeout period of the watchdog.
The watchdog counter (WDOG_CNTH and WDOG_CNTL) is continuously compared
with the timeout value (WDOG_TOVALH and WDOG_TOVALL). If the counter
reaches the timeout value, the watchdog forces a reset.
NOTE
Do not write 0 to the Watchdog Timeout Value Register,
otherwise, the watchdog always generates a reset.
Address: 4005_2000h base + 4h offset = 4005_2004h
Bit
Read
Write
Reset
7
6
5
4
3
2
1
0
0
0
0
0
TOVALHIGH
0
0
0
0
WDOG_TOVALH field descriptions
Field
TOVALHIGH
Description
High byte of the timeout value
16.2.6 Watchdog Timeout Value Register: Low (WDOG_TOVALL)
See the description of the WDOG_TOVALH register.
NOTE
All the bits reset to 0 in read.
Address: 4005_2000h base + 5h offset = 4005_2005h
Bit
Read
Write
Reset
7
6
5
4
3
2
1
0
0
1
0
0
TOVALLOW
0
0
0
0
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
215
Memory map and register definition
WDOG_TOVALL field descriptions
Field
TOVALLOW
Description
Low byte of the timeout value
16.2.7 Watchdog Window Register: High (WDOG_WINH)
This section describes the watchdog window registers: high (WDOG_WINH) and low
(WDOG_WINL) combined. When window mode is enabled (WDOG_CS2[WIN] is set),
WDOG_WINH and WDOG_WINL determine the earliest time that a refresh sequence is
considered valid. See the Watchdog refresh mechanism section.
WDOG_WINH and WDOG_WINL must be less than WDOG_TOVALH and
WDOG_TOVALL.
Address: 4005_2000h base + 6h offset = 4005_2006h
Bit
Read
Write
Reset
7
6
5
4
3
2
1
0
0
0
0
0
WINHIGH
0
0
0
0
WDOG_WINH field descriptions
Field
WINHIGH
Description
High byte of Watchdog Window
16.2.8 Watchdog Window Register: Low (WDOG_WINL)
See the description of the WDOG_WINH register.
Address: 4005_2000h base + 7h offset = 4005_2007h
Bit
Read
Write
Reset
7
6
5
4
3
2
1
0
0
0
0
0
WINLOW
0
0
0
0
WDOG_WINL field descriptions
Field
WINLOW
Description
Low byte of Watchdog Window
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
216
Freescale Semiconductor, Inc.
Chapter 16 Watchdog Timer (WDOG)
16.3 Functional description
The WDOG module provides a fail safe mechanism to ensure the system can be reset to a
known state of operation in case of system failure, such as the CPU clock stopping or
there being a run away condition in the software code. The watchdog counter runs
continuously off a selectable clock source and expects to be serviced (refreshed)
periodically. If it is not, it resets the system.
The timeout period, window mode, and clock source are all programmable but must be
configured within 128 bus clocks after a reset.
16.3.1 Watchdog refresh mechanism
The watchdog resets the MCU if the watchdog counter is not refreshed. A robust refresh
mechanism makes it very unlikely that the watchdog can be refreshed by runaway code.
To refresh the watchdog counter, software must execute a refresh write sequence before
the timeout period expires. In addition, if window mode is used, software must not start
the refresh sequence until after the time value set in the WDOG_WINH and
WDOG_WINL registers. See the following figure.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
217
Functional description
WDOG counter
WDOG_TOVALH and
WDOG_TOVALL
WDOG_WINH and
WDOG_WINL
Refresh opportunity
in window mode
0
Refresh opportunity (not in window mode)
Time
Figure 16-10. Refresh opportunity for the Watchdog counter
16.3.1.1 Window mode
Software finishing its main control loop faster than expected could be an indication of a
problem. Depending on the requirements of the application, the WDOG can be
programmed to force a reset when refresh attempts are early.
When Window mode is enabled, the watchdog must be refreshed after the counter has
reached a minimum expected time value; otherwise, the watchdog resets the MCU. The
minimum expected time value is specified in the WDOG_WINH:L registers. Setting
CS1[WIN] enables Window mode.
16.3.1.2 Refreshing the Watchdog
The refresh write sequence is a write of 0x02A6 followed by a write of 0x80B4 to the
WDOG_CNTH and WDOG_CNTL registers. The write of the 0x80B4 must occur within
16 bus clocks after the write of 0x02A6; otherwise, the watchdog resets the MCU.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
218
Freescale Semiconductor, Inc.
Chapter 16 Watchdog Timer (WDOG)
Note
Before starting the refresh sequence, disable global interrupts.
Otherwise, an interrupt could effectively invalidate the refresh
sequence if writing the four bytes takes more than 16 bus
clocks. Re-enable interrupts when the sequence is finished.
16.3.1.3 Example code: Refreshing the Watchdog
The following code segment shows the refresh write sequence of the WDOG module.
NOTE
The following example code combines the 8-bit
WDOG_CNTH and WDOG_CNTL as one 16-bit
WDOG_CNT, the 8-bit WDOG_TOVALH and
WDOG_TOVALL as one 16-bit WDOG_TOVAL,
WDOG_WINH and WDOG_WINL as WDOG_WIN and uses
16-bit access.
/* Refresh watchdog */
for (;;) // main loop
{
...
DisableInterrupts; // disable global interrupt
WDOG_CNT = 0x02A6; // write the 1st refresh word
WDOG_CNT = 0x80B4; // write the 2nd refresh word to refresh counter
EnableInterrupts; // enable global interrupt
}
...
16.3.2 Configuring the Watchdog
All watchdog control bits, timeout value, and window value are write-once after reset.
This means that after a write has occurred they cannot be changed unless a reset occurs.
This provides a robust mechanism to configure the watchdog and ensure that a runaway
condition cannot mistakenly disable or modify the watchdog configuration after
configured.
This is guaranteed by the user configuring the window and timeout value first, followed
by the other control bits, and ensuring that CS1[UPDATE] is also set to 0. The new
configuration takes effect only after all registers except WDOG_CNTH:L are written
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
219
Functional description
once after reset. Otherwise, the WDOG uses the reset values by default. If window mode
is not used (CS2[WIN] is 0), writing to WDOG_WINH:L is not required to make the new
configuration take effect.
16.3.2.1 Reconfiguring the Watchdog
In some cases (such as when supporting a bootloader function), users may want to
reconfigure or disable the watchdog without forcing a reset first. By setting
CS1[UPDATE] to a 1 on the initial configuration of the watchdog after a reset, users can
reconfigure the watchdog at any time by executing an unlock sequence. (Conversely, if
CS1[UPDATE] remains 0, the only way to reconfigure the watchdog is by initiating a
reset.) The unlock sequence is similar to the refresh sequence but uses different values.
16.3.2.2 Unlocking the Watchdog
The unlock sequence is a write to the WDOG_CNTH:L registers of 0x20C5 followed by
0x28D9 within 16 bus clocks at any time after the watchdog has been configured. On
completing the unlock sequence, the user must reconfigure the watchdog within 128 bus
clocks; .
NOTE
Due to 128 bus clocks requirement for reconfiguring the
watchdog, some delays must be inserted before executing
STOP or WAIT instructions after reconfiguring the watchdog.
This ensures that the watchdog's new configuration takes effect
before MCU enters low power mode. Otherwise, the MCU may
not be waken up from low power mode.
16.3.2.3 Example code: Reconfiguring the Watchdog
The following code segment shows an example reconfiguration of the WDOG module.
/* Initialize watchdog with ~1-kHz clock source, ~1s time-out */
DisableInterrupts; // disable global interrupt
WDOG_CNT = 0x20C5; // write the 1st unlock word
WDOG_CNT = 0x28D9; // write the 2nd unlock word
WDOG_TOVAL = 1000; // setting timeout value
WDOG_CS2 = WDOG_CS2_CLK_MASK; // setting 1-kHz clock source
WDOG_CS1 = WDOG_CS1_EN_MASK; // enable counter running
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
220
Freescale Semiconductor, Inc.
Chapter 16 Watchdog Timer (WDOG)
EnableInterrupts; // enable global interrupt
16.3.3 Clock source
The watchdog counter has four clock source options selected by programming
CS2[CLK]:
• bus clock
• internal Low-Power Oscillator (LPO) running at approximately 1 kHz (This is the
default source.)
• internal 32 kHz clock
• external clock
The options allow software to select a clock source independent of the bus clock for
applications that need to meet more robust safety requirements. Using a clock source
other than the bus clock ensures that the watchdog counter continues to run if the bus
clock is somehow halted; see Backup reset.
An optional fixed prescaler for all clock sources allows for longer timeout periods. When
CS2[PRES] is set, the clock source is prescaled by 256 before clocking the watchdog
counter.
The following table summarizes the different watchdog timeout periods available.
Table 16-10. Watchdog timeout availability
Reference clock
Internal ~1 kHz (LPO)
Internal ~32 kHz
1 MHz (from bus or external)
20 MHz (from bus or external)
Prescaler
Watchdog time-out availability
Pass through
~1 ms–65.5 s1
÷256
~256 ms–16,777 s
Pass through
~31.25 µs–2.048 s
÷256
~8 ms–524.3 s
Pass through
1 µs–65.54 ms
÷256
256 µs–16.777 s
Pass through
50 ns–3.277 ms
÷256
12.8 µs–838.8 ms
1. The default timeout value after reset is approximately 4 ms.
NOTE
When the programmer switches clock sources during
reconfiguration, the watchdog hardware holds the counter at
zero for 2.5 periods of the previous clock source and 2.5
periods of the new clock source after the configuration time
period (128 bus clocks) ends. This delay ensures a smooth
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
221
Functional description
transition before restarting the counter with the new
configuration.
16.3.4 Using interrupts to delay resets
When interrupts are enabled (CS1[INT] = 1), the watchdog first generates an interrupt
request upon a reset triggering event (such as a counter timeout or invalid refresh
attempt). The watchdog delays forcing a reset for 128 bus clocks to allow the interrupt
service routine (ISR) to perform tasks, such as analyzing the stack to debug code.
When interrupts are disabled (CS1[INT] = 0), the watchdog does not delay forcing a
reset.
16.3.5 Backup reset
NOTE
A clock source other than the bus clock must be used as the
reference clock for the counter; otherwise, the backup reset
function is not available.
The backup reset function is a safeguard feature that independently generates a reset in
case the main WDOG logic loses its clock (the bus clock) and can no longer monitor the
counter. If the watchdog counter overflows twice in succession (without an intervening
reset), the backup reset function takes effect and generates a reset.
16.3.6 Functionality in debug and low-power modes
By default, the watchdog is not functional in Active Background mode, Wait mode, or
Stop mode. However, the watchdog can remain functional in these modes as follows:
• For Active Background mode, set CS1[DBG]. (This way the watchdog is functional
in Active Background mode even when the CPU is held by the Debug module.)
• For Wait mode, set CS1[WAIT].
• For Stop mode, set CS1[STOP].
NOTE
The watchdog can not generate interrupt in Stop mode even if
CS1[STOP] is set and will not wake the MCU from Stop mode.
It can generate reset during Stop mode.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
222
Freescale Semiconductor, Inc.
Chapter 16 Watchdog Timer (WDOG)
For Active Background mode and Stop mode, in addition to the
above configurations, a clock source other than the bus clock
must be used as the reference clock for the counter; otherwise,
the watchdog cannot function.
16.3.7 Fast testing of the watchdog
Before executing application code in safety critical applications, users are required to test
that the watchdog works as expected and resets the MCU. Testing every bit of a 16-bit
counter by letting it run to the overflow value takes a relatively long time (64 kHz
clocks).
To help minimize the startup delay for application code after reset, the watchdog has a
feature to test the watchdog more quickly by splitting the counter into its constituent
byte-wide stages. The low and high bytes are run independently and tested for timeout
against the corresponding byte of the timeout value register. (For complete coverage
when testing the high byte of the counter, the test feature feeds the input clock via the 8th
bit of the low byte, thus ensuring that the overflow connection from the low byte to the
high byte is tested.)
Using this test feature reduces the test time to 512 clocks (not including overhead, such as
user configuration and reset vector fetches). To further speed testing, use a faster clock
(such as the bus clock) for the counter reference.
On a power-on reset, the POR bit in the system reset register is set, indicating the user
should perform the WDOG fast test.
16.3.7.1 Testing each byte of the counter
The test procedure follows these steps:
1. Program the preferred watchdog timeout value in the WDOG_TOVALH and
WDOG_TOVALL registers during the watchdog configuration time period.
2. Select a byte of the counter to test using the WDOG_CS1[TST] = 10b for the low
byte; WDOG_CS1[TST] = 11b for the high byte.
3. Wait for the watchdog to timeout. Optionally, in the idle loop, increment RAM
locations as a parallel software counter for later comparison. Because the RAM is not
affected by a watchdog reset, the timeout period of the watchdog counter can be
compared with the software counter to verify the timeout period has occurred as
expected.
4. The watchdog counter times out and forces a reset.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
223
Functional description
5. Confirm the WDOG flag in the system reset register is set, indicating that the
watchdog caused the reset. (The POR flag remains clear.)
6. Confirm that WDOG_CS1[TST] shows a test (10b or 11b) was performed.
If confirmed, the count and compare functions work for the selected byte. Repeat the
procedure, selecting the other byte in step 2.
NOTE
WDOG_CS1[TST] is cleared by a POR only and not affected
by other resets.
16.3.7.2 Entering user mode
After successfully testing the low and high bytes of the watchdog counter, the user can
configure WDOG_CS1[TST] to 01b to indicate the watchdog is ready for use in
application user mode. Thus if a reset occurs again, software can recognize the reset
trigger as a real watchdog reset caused by runaway or faulty application code.
As an ongoing test when using the default 1-kHz clock source, software can periodically
read the WDOG_CNTH and WDOG_CNTL registers to ensure the counter is being
incremented.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
224
Freescale Semiconductor, Inc.
Chapter 17
Bit Manipulation Engine (BME)
17.1 Introduction
The Bit Manipulation Engine (BME) provides hardware support for atomic read-modifywrite memory operations to the peripheral address space in Cortex-M0+ based
microcontrollers.
This architectural capability is also known as "decorated storage" as it defines a
mechanism for providing additional semantics for load and store operations to memorymapped peripherals beyond just the reading and writing of data values to the addressed
memory locations. In the BME definition, the "decoration", that is, the additional
semantic information, is encoded into the peripheral address used to reference the
memory.
By combining the basic load and store instructions of the ARM Cortex-M instruction set
architecture (v6M, v7M) with the concept of decorated storage provided by the BME, the
resulting implementation provides a robust and efficient read-modify-write capability to
this class of ultra low-end microcontrollers. The resulting architectural capability defined
by this core platform function is targeted at the manipulation of n-bit fields in peripheral
registers and is consistent with I/O hardware addressing in the Embedded C standard. For
most BME commands, a single core read or write bus cycle is converted into an atomic
read-modify-write, that is, an indivisible "read followed by a write" bus sequence.
BME decorated references are only available on system bus transactions generated by the
processor core and targeted at the standard 512 KB peripheral address space based at
0x4000_00001 and SRAM_U space based at 0x2000_0000. The decoration semantic is
embedded into address bits[28:19], creating a 448 MB space at addresses 0x4400_0000–
1.
To be perfectly accurate, the peripheral address space occupies a 516 KB region: 512 KB based at 0x4000_0000 plus a 4
KB space based at 0x400F_F000 for GPIO accesses. This organization provides compatibility with the Kinetis K Family.
Attempted accesses to the memory space located between 0x4008_0000 - 0x400F_EFFF are error terminated due to an
illegal address.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
225
Introduction
0x5FFF_FFFF for AIPS and a 448 MB space at addresses 0x2400_0000–0x3FFF_FFFF
for SRAM_U; these bits are stripped out of the actual address sent to the peripheral bus
controller and used by the BME to define and control its operation.
17.1.1 Overview
The following figure is a generic block diagram of the processor core and platform for
this class of ultra low-end microcontrollers.
Cortex-M0+ Core
NVIC
CM0+ Core Platform
Fetch
Dbg
AGU
Dec
Rn
LD/ST
SHFT
ALU
MUL
IO Port
32
PRAM
RAM
Array
GPIO
BME
m0
s1
AXBS
-Lite
32
PBRIDGE
s2
Slave
Peripherals
s0
FMC
32
NVM
Array
Note: BME can be accessed only by the core.
Figure 17-1. Cortex-M0+ core platform block diagram
As shown in the block diagram, the BME module interfaces to the master port on the
crossbar switch allowing it to support atomic read-modify-write operations to the
SRAM_U (shown as platform RAM (PRAM) in the figure) and the Peripheral Bridge
(PBRIDGE) controller. The BME hardware microarchitecture is a 2-stage pipeline design
matching the protocol of the AMBA-AHB system bus interfaces. The PBRIDGE module
converts the AHB system bus protocol into the IPS/APB protocol used by the attached
slave peripherals.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
226
Freescale Semiconductor, Inc.
Chapter 17 Bit Manipulation Engine (BME)
17.1.2 Features
The key features of the BME include:
• Lightweight implementation of decorated storage for selected address spaces
• Additional access semantics encoded into the reference address
• Resides between processor core and a switch master port
• Two-stage pipeline design matching the AHB system bus protocol
• Combinationally passes non-decorated accesses to slave bus controllers
• Conversion of decorated loads and stores from processor core into atomic readmodify-writes
• Decorated loads support unsigned bit field extracts, load-and-{set,clear} 1-bit
operations
• Decorated stores support bit field inserts, logical AND, OR, and XOR operations
• Support for byte, halfword and word-sized decorated operations
• Supports minimum signal toggling on AHB output bus to reduce power dissipation
17.1.3 Modes of operation
The BME module does not support any special modes of operation. As a memorymapped device located on a crossbar master AHB system bus port, BME responds strictly
on the basis of memory addresses for accesses to the SRAM_U and peripheral bridge bus
controller.
All functionality associated with the BME module resides in the core platform's clock
domain; this includes its connections with the crossbar master port, SRAM_U and the
PBRIDGE bus controller.
17.2 Memory map and register definition
The BME module provides a memory-mapped capability and does not include any
programming model registers.
The exact set of functions supported by the BME are detailed in the Functional
description.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
227
Functional description
The peripheral address space occupies a 516 KB region: 512 KB based at 0x4000_0000
plus a 4 KB space based at 0x400F_F000 for GPIO accesses; the decorated address space
is mapped to the 448 MB region located at 0x4400_0000–0x5FFF_FFFF. The decorated
address space associated with the SRAM_U is the 448 MB region mapped at
0x2400_0000 - 0x3FFF_FFFF.
17.3 Functional description
Information found here details the specific functions supported by the BME.
Recall the combination of the basic load and store instructions of the Cortex-M
instruction set architecture (v6M, v7M) plus the concept of decorated storage provided by
the BME, the resulting implementation provides a robust and efficient read-modify-write
capability to this class of ultra low-end microcontrollers. The resulting architectural
capability defined by this core platform function is targeted at the manipulation of n-bit
fields in peripheral registers and RAM and is consistent with I/O hardware addressing in
the Embedded C standard. For most BME commands, a single core read or write bus
cycle is converted into an atomic read-modify-write, that is, an indivisible "read followed
by a write" bus sequence.
Consider decorated store operations first, then decorated loads.
17.3.1 BME decorated stores
The functions supported by the BME's decorated stores include three logical operators
(AND, OR, XOR) plus a bit field insert.
For all these operations, BME converts a single decorated AHB store transaction into a 2cycle atomic read-modify-write sequence, where the combined read-modify operation is
performed in the first AHB data phase, and then the write is performed in the second
AHB data phase.
A generic timing diagram of a decorated store showing a peripheral bit field insert
operation is shown as follows:
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
228
Freescale Semiconductor, Inc.
Chapter 17 Bit Manipulation Engine (BME)
CYCLE RULER
x
x+1
x+2
x+3
hclk
BME AHB Input Bus
mx_haddr
next
5..v_wxyz
mx_hattr
next
mx_hwrite
next
mx_hwdata
wdata
mx_hrdata
mx_hready
BME AHB Output Bus
sx_haddr
400v_wxyz
400v_wxyz
next
sx_hattr
next
sx_hwrite
next
sx_hwdata
wdata bfi rdata
sx_hrdata
rdata
sx_hready
BME States + Datapath
control_state_dp1
control_state_dp2
reg_addr_data_dp
5..v_wxyz
wdata bfi rdata
Figure 17-2. Decorated store: bit field insert timing diagram
All the decorated store operations follow the same execution template shown in Figure
17-2, a two-cycle read-modify-write operation:
1. Cycle x, 1st AHB address phase: Write from input bus is translated into a read
operation on the output bus using the actual memory address (with the decoration
removed) and then captured in a register.
2. Cycle x+1, 2nd AHB address phase: Write access with the registered (but actual)
memory address is output
3. Cycle x+1, 1st AHB data phase: Memory read data is modified using the input bus
write data and the function defined by the decoration and captured in a data register;
the input bus cycle is stalled.
4. Cycle x+2, 2nd AHB data phase: Registered write data is sourced onto the output
write data bus.
NOTE
Any wait states inserted by the slave device are simply passed
through the BME back to the master input bus, stalling the
AHB transaction cycle for cycle.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
229
Functional description
17.3.1.1 Decorated store logical AND (AND)
This command performs an atomic read-modify-write of the referenced memory location.
1. First, the location is read;
2. It is then modified by performing a logical AND operation using the write data
operand sourced for the system bus cycle
3. Finally, the result of the AND operation is written back into the referenced memory
location.
The data size is specified by the write operation and can be byte (8-bit), halfword (16-bit)
or word (32-bit). The core performs the required write data lane replication on byte and
halfword transfers.
31 30 29 28 27 26 25 24 23 22
ioandb 0
*
ioandh 0
*
ioandw 0
*
21 20 19 18 17 16 15 14 13 12
11 10
9
*
0
0
1
-
-
-
-
-
-
mem_addr
*
0
0
1
-
-
-
-
-
-
*
0
0
1
-
-
-
-
-
-
mem_addr
mem_addr
8
7
6
5
4
3
2
0
1
0
0
0
Figure 17-3. Decorated store address: logical AND
See Figure 17-3 where addr[30:29] = 01 for SRAM_U, addr[30:29] = 10 for peripheral,
addr[28:26] = 001 specifies the AND operation, and mem_addr[19:0] specifies the
address offset into the space based at 0x2000_0000 for SRAM_U, and 0x4000_0000 for
peripherals. The "-" indicates an address bit "don't care".
The decorated AND write operation is defined in the following pseudo-code as:
ioand<sz>(accessAddress, wdata)
tmp
= mem[accessAddress & 0xE00FFFFF, size]
tmp
= tmp & wdata
mem[accessAddress & 0xE00FFFFF, size] = tmp
//
//
//
//
decorated store AND
memory read
modify
memory write
where the operand size <sz> is defined as b(yte, 8-bit), h(alfword, 16-bit) and w(ord, 32bit). This notation is used throughout the document.
In the cycle definition tables, the notations AHB_ap and AHB_dp refer to the address and
data phases of the BME AHB transaction. The cycle-by-cycle BME operations are
detailed in the following table.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
230
Freescale Semiconductor, Inc.
Chapter 17 Bit Manipulation Engine (BME)
Table 17-1. Cycle definitions of decorated store: logical AND
Pipeline stage
Cycle
x
BME AHB_ap
x+1
Forward addr to memory;
Decode decoration; Convert
master_wt to slave_rd;
Capture address, attributes
BME AHB_dp
<previous>
x+2
Recirculate captured addr +
attr to memory as slave_wt
<next>
Perform memory read; Form
(rdata & wdata) and capture
destination data in register
Perform write sending
registered data to memory
17.3.1.2 Decorated store logical OR (OR)
This command performs an atomic read-modify-write of the referenced memory location.
1. First, the location is read.
2. It is then modified by performing a logical OR operation using the write data operand
sourced for the system bus cycle.
3. Finally, the result of the OR operation is written back into the referenced memory
location.
The data size is specified by the write operation and can be byte (8-bit), halfword (16-bit)
or word (32-bit). The core performs the required write data lane replication on byte and
halfword transfers.
31 30 29 28 27 26 25 24 23 22
21 20 19 18 17 16 15 14 13 12
ioorb
0
*
*
ioorh
0
*
ioorw
0
*
0
1
*
0
*
0
11 10
9
0
-
-
-
-
-
-
mem_addr
1
0
-
-
-
-
-
-
1
0
-
-
-
-
-
-
mem_addr
mem_addr
8
7
6
5
4
3
2
1
0
0
0
0
Figure 17-4. Decorated address store: logical OR
See Figure 17-4,where addr[30:29] = 01 for SRAM_U, addr[30:29] =10 for peripheral,
addr[28:26] = 010 specifies the OR operation, and mem_addr[19:0] specifies the address
offset into the space based at 0x2000_0000 for SRAM_U, and 0x4000_0000 for
peripherals. The "-" indicates an address bit "don't care".
The decorated OR write operation is defined in the following pseudo-code as:
ioor<sz>(accessAddress, wdata)
// decorated store OR
tmp
= mem[accessAddress & 0xE00FFFFF, size]
tmp
= tmp | wdata
mem[accessAddress & 0xE00FFFFF, size] = tmp
// memory read
// modify
// memory write
The cycle-by-cycle BME operations are detailed in the following table.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
231
Functional description
Table 17-2. Cycle definitions of decorated store: logical OR
Pipeline stage
Cycle
x
BME AHB_ap
x+1
Forward addr to memory;
Decode decoration; Convert
master_wt to slave_rd;
Capture address, attributes
BME AHB_dp
<previous>
x+2
Recirculate captured addr +
attr to memory as slave_wt
<next>
Perform memory read; Form
(rdata | wdata) and capture
destination data in register
Perform write sending
registered data to memory
17.3.1.3 Decorated store logical XOR (XOR)
This command performs an atomic read-modify-write of the referenced memory location.
1. First, the location is read.
2. It is then modified by performing a logical XOR (exclusive-OR) operation using the
write data operand sourced for the system bus cycle.
3. Finally, the result of the XOR operation is written back into the referenced memory
location.
The data size is specified by the write operation and can be byte (8-bit), halfword (16-bit)
or word (32-bit). The core performs the required write data lane replication on byte and
halfword transfers.
31 30 29 28 27 26 25 24 23 22
21 20 19 18 17 16 15 14 13 12
ioxorb
0
*
*
ioxorh
0
*
ioxorw 0
*
11 10
9
0
1
1
-
-
-
-
-
-
mem_addr
*
0
1
1
-
-
-
-
-
-
*
0
1
1
-
-
-
-
-
-
mem_addr
mem_addr
8
7
6
5
4
3
2
1
0
0
0
0
Figure 17-5. Decorated address store: logical XOR
See Figure 17-5, where addr[30:29] = 01 for SRAM_U, addr[30:29] =10 for peripheral,
addr[28:26] = 011 specifies the XOR operation, and mem_addr[19:0] specifies the
address offset into the peripheral space based at 0x2000_0000 for SRAM_U, and
0x4000_0000 for peripherals. The "-" indicates an address bit "don't care".
The decorated XOR write operation is defined in the following pseudo-code as:
ioxor<sz>(accessAddress, wdata)
// decorated store XOR
tmp
= mem[accessAddress & 0xE00FFFFF, size]
tmp
= tmp ^ wdata
mem[accessAddress & 0xE00FFFFF, size] = tmp
// memory read
// modify
// memory write
The cycle-by-cycle BME operations are detailed in the following table.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
232
Freescale Semiconductor, Inc.
Chapter 17 Bit Manipulation Engine (BME)
Table 17-3. Cycle definitions of decorated store: logical XOR
Pipeline Stage
Cycle
x
BME AHB_ap
Forward addr to memory;
Decode decoration; Convert
master_wt to slave_rd;
Capture address, attributes
BME AHB_dp
<previous>
x+1
x+2
Recirculate captured addr +
attr to memory as slave_wt
Perform memory read; Form
(rdata ^ wdata) and capture
destination data in register
<next>
Perform write sending
registered data to memory
17.3.1.4 Decorated store bit field insert (BFI)
This command inserts a bit field contained in the write data operand, defined by LSB
position (b) and the bit field width (w+1), into the memory "container" defined by the
access size associated with the store instruction using an atomic read-modify-write
sequence.
The data size is specified by the write operation and can be byte (8-bit), halfword (16-bit)
or word (32-bit).
NOTE
For the word sized operation, the maximum bit field width is 16
bits. The core performs the required write data lane replication
on byte and halfword transfers.
The BFI operation can be used to insert a single bit into a peripheral. For this case, the w
field is simply set to 0, indicating a bit field width of 1.
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
iobfib
0
iobfih
0
iobfiw
0
9
*
1
-
-
b
b b
-
w w w
mem_addr
*
*
1
-
b
b
b b
w w w w
mem_addr
*
*
1
b b
w w w w
mem_addr
*
b
b
b
8
7
6
5
4
3
2
1
0
0
0
0
Figure 17-6. Decorated address store: bit field insert
where addr[30:29] = 01 for SRAM_U, addr[30:29] =10 for peripheral,addr[28] = 1
signals a BFI operation, addr[27:23] is "b", the LSB identifier, addr[22:19] is "w", the bit
field width minus 1 identifier, and addr[18:0] specifies the address offset into the
peripheral space based at 0x2000_0000 for SRAM_U, and 0x4000_0000 for peripherals.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
233
Functional description
The "-" indicates an address bit "don't care". Note, unlike the other decorated store
operations, BFI uses addr[19] as the least significant bit in the "w" specifier and not as an
address bit.
The decorated BFI write operation is defined in the following pseudo-code as:
iobfi<sz>(accessAddress, wdata)
// decorated bit field insert
tmp
mask
tmp
// memory read
// generate bit mask
// modify
= mem[accessAddress & 0xE007FFFF, size]
= ((1 << (w+1)) - 1) << b
= tmp
& ~mask
| wdata & mask
mem[accessAddress & 0xE007FFFF, size] = tmp
// memory write
The write data operand (wdata) associated with the store instruction contains the bit field
to be inserted. It must be properly aligned within a right-aligned container, that is, within
the lower 8 bits for a byte operation, the lower 16 bits for a halfword, or the entire 32 bits
for a word operation.
To illustrate, consider the following example of the insertion of the 3-bit field "xyz" into
an 8-bit memory container, initially set to "abcd_efgh". For all cases, w is 2, signaling a
bit field width of 3.
if b = 0 and the decorated store (strb)
then destination is "abcd_exyz"
if b = 1 and the decorated store (strb)
then destination is "abcd_xyzh"
if b = 2 and the decorated store (strb)
then destination is "abcx_yzgh"
if b = 3 and the decorated store (strb)
then destination is "abxy_zfgh"
if b = 4 and the decorated store (strb)
then destination is "axyz_efgh"
if b = 5 and the decorated store (strb)
then destination is "xyzd_efgh"
if b = 6 and the decorated store (strb)
then destination is "yzcd_efgh"
if b = 7 and the decorated store (strb)
then destination is "zbcd_efgh"
Rt register[7:0] = ----_-xyz,
Rt register[7:0] = ----_xyz-,
Rt register[7:0] = ---x_yz--,
Rt register[7:0] = --xy_z---,
Rt register[7:0] = -xyz_----,
Rt register[7:0] = xyz-_----,
Rt register[7:0] = yz--_----,
Rt register[7:0] = z---_----,
Note from the example, when the starting bit position plus the field width exceeds the
container size, only part of the source bit field is inserted into the destination memory
location. Stated differently, if (b + w+1) > container_width, only the low-order
"container_width - b" bits are actually inserted.
The cycle-by-cycle BME operations are detailed in the following table.
Table 17-4. Cycle definitions of decorated store: bit field insert
Pipeline stage
Cycle
x
BME AHB_ap
Forward addr to memory;
Decode decoration; Convert
master_wt to slave_rd;
Capture address, attributes
x+1
x+2
Recirculate captured addr +
attr to memory as slave_wt
<next>
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
234
Freescale Semiconductor, Inc.
Chapter 17 Bit Manipulation Engine (BME)
Table 17-4. Cycle definitions of decorated store: bit field insert (continued)
Pipeline stage
Cycle
x
BME AHB_dp
<previous>
x+1
Perform memory read; Form
bit mask; Form bitwise
((mask) ? wdata : rdata)) and
capture destination data in
register
x+2
Perform write sending
registered data to memory
17.3.2 BME decorated loads
The functions supported by the BME's decorated loads include two single-bit load-and{set, clear} operators plus unsigned bit field extracts.
For the two load-and-{set, clear} operations, BME converts a single decorated AHB load
transaction into a two-cycle atomic read-modify-write sequence, where the combined
read-modify operations are performed in the first AHB data phase, and then the write is
performed in the second AHB data phase as the original read data is returned to the
processor core. For an unsigned bit field extract, the decorated load transaction is stalled
for one cycle in the BME as the data field is extracted, then aligned and returned to the
processor in the second AHB data phase. This is the only decorated transaction that is not
an atomic read-modify-write, as it is a simple data read.
A generic timing diagram of a decorated load showing a peripheral load-and-set 1-bit
operation is shown as follows.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
235
Functional description
CYCLE RULER
hclk
x
x+2
x+1
x+3
BME AHB Input Bus
mx_haddr
4c.v_wxyz
next
mx_hattr
next
mx_hwrite
next
mx_hwdata
mx_hrdata
orig_1bit
mx_hready
BME AHB Output Bus
sx_haddr
400v_wxyz
400v_wxyz
next
sx_hattr
next
sx_hwrite
next
sx_hwdata
rdata + 1bit
sx_hrdata
rdata
sx_hready
BME States + Datapath
control_state_dp1
control_state_dp2
reg_addr_data_dp
4c.v_wxyz
rdata + 1bit
Figure 17-7. Decorated load: load-and-set 1-bit field insert timing diagram
Decorated load-and-{set, clear} 1-bit operations follow the execution template shown in
the above figure: a 2-cycle read-modify-write operation:
1. Cycle x, first AHB address phase: Read from input bus is translated into a read
operation on the output bus with the actual memory address (with the decoration
removed) and then captured in a register
2. Cycle x+1, second AHB address phase: Write access with the registered (but actual)
memory address is output
3. Cycle x+1, first AHB data phase: The "original" 1-bit memory read data is captured
in a register, while the 1-bit field is set or clear based on the function defined by the
decoration with the modified data captured in a register; the input bus cycle is stalled
4. Cycle x+2, second AHB data phase: The selected original 1-bit is right-justified,
zero-filled and then driven onto the input read data bus, while the registered write
data is sourced onto the output write data bus
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
236
Freescale Semiconductor, Inc.
Chapter 17 Bit Manipulation Engine (BME)
NOTE
Any wait states inserted by the slave device are simply passed
through the BME back to the master input bus, stalling the
AHB transaction cycle for cycle.
A generic timing diagram of a decorated load showing an unsigned peripheral bit field
operation is shown in the following figure.
1
2
3
5..v_wxyz
4
next
next
next
ubfx
400v_wxyz
next
next
next
rdata
5..v_wxyz
rdata
Figure 17-8. Decorated load: unsigned bit field insert timing diagram
The decorated unsigned bit field extract follows the same execution template shown in
the above figure, a 2-cycle read operation:
• Cycle x, 1st AHB address phase: Read from input bus is translated into a read
operation on the output bus with the actual memory address (with the decoration
removed) and then captured in a register
• Cycle x+1, 2nd AHB address phase: Idle cycle
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
237
Functional description
• Cycle x+1, 1st AHB data phase: A bit mask is generated based on the starting bit
position and the field width; the mask is AND'ed with the memory read data to
isolate the bit field; the resulting data is captured in a data register; the input bus
cycle is stalled
• Cycle x+2, 2nd AHB data phase: Registered data is logically right-aligned for proper
alignment and driven onto the input read data bus
NOTE
Any wait states inserted by the slave device are simply passed
through the BME back to the master input bus, stalling the
AHB transaction cycle for cycle.
17.3.2.1 Decorated load: load-and-clear 1 bit (LAC1)
This command loads a 1-bit field defined by the LSB position (b) into the core's general
purpose destination register (Rt) and zeroes the bit in the memory space after performing
an atomic read-modify-write sequence.
The extracted 1-bit data field from the memory address is right-justified and zero-filled in
the operand returned to the core.
The data size is specified by the read operation and can be byte (8-bit), halfword (16-bit)
or word (32-bit).
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
9
8
iolac1b 0
*
*
0
1
0
-
-
b
b
b
-
mem_addr
iolac1h 0
*
*
0
1
0
-
b
b
b
b
-
mem_addr
iolac1w 0
*
*
0
1
0
b
b
b
b
b
-
mem_addr
7
6
5
4
3
2
1
0
0
0
0
Figure 17-9. Decorated load address: load-and-clear 1 bit
See Figure 17-9 where addr[30:29] = 01 for SRAM_U, addr[30:29] = 10 for peripheral,
addr[28:26] = 010 specifies the load-and-clear 1 bit operation, addr[25:21] is "b", the bit
identifier, and mem_addr[19:0] specifies the address offset into the space based at
0x2000_0000 for SRAM_U, and 0x4000_0000 for peripheral. The "-" indicates an
address bit "don't care".
The decorated load-and-clear 1-bit read operation is defined in the following pseudo-code
as:
rdata =
iolac1<sz>(accessAddress)
tmp
= mem[accessAddress & 0xE00FFFFF, size]
mask = 1 << b
rdata = (tmp & mask) >> b
// decorated load-and-clear 1
// memory read
// generate bit mask
// read data returned to core
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
238
Freescale Semiconductor, Inc.
Chapter 17 Bit Manipulation Engine (BME)
tmp
= tmp & ~mask
mem[accessAddress & 0xE00FFFFF, size] = tmp
// modify
// memory write
The cycle-by-cycle BME operations are detailed in the following table.
Table 17-5. Cycle definitions of decorated load: load-and-clear 1 bit
Pipeline Stage
Cycle
x
BME AHB_ap
x+1
Forward addr to memory;
Decode decoration; Capture
address, attributes
BME AHB_dp
<previous>
x+2
Recirculate captured addr +
attr to memory as slave_wt
<next>
Perform memory read; Form
bit mask; Extract bit from
rdata; Form (rdata & ~mask)
and capture destination data
in register
Return extracted bit to master;
Perform write sending
registered data to memory
17.3.2.2 Decorated Load: Load-and-Set 1 Bit (LAS1)
This command loads a 1-bit field defined by the LSB position (b) into the core's general
purpose destination register (Rt) and sets the bit in the memory space after performing an
atomic read-modify-write sequence.
The extracted one bit data field from the memory address is right justified and zero filled
in the operand returned to the core.
The data size is specified by the read operation and can be byte (8-bit), halfword (16-bit)
or word (32-bit).
31 30 29 28 27 26 25 24 23 22
21 20 19 18 17 16 15 14 13 12
iolaslb
0
iolaslh
0
iolaslw 0
11 10
9
*
0
1
1
-
-
b
b
b
-
mem_addr
*
*
0
1
1
-
b
b
b
b
-
*
*
0
1
1
b
b
b
b
b
-
mem_addr
mem_addr
*
8
7
6
5
4
3
2
1
0
0
0
0
Figure 17-10. Decorated load address: load-and-set 1 bit
where addr[30:29] = 01 for SRAM_U, addr[30:29] = 10 for peripheral, addr[28:26] = 011
specifies the load-and-set 1 bit operation, addr[25:21] is "b", the bit identifier, and
mem_addr[19:0] specifies the address offset into the space based at 0x2000_0000 for
SRAM_U, and 0x4000_0000 for peripheral. The "-" indicates an address bit "don't care".
The decorated Load-and-Set 1 Bit read operation is defined in the following pseudo-code
as:
rdata =
iolas1<sz>(accessAddress)
// decorated load-and-set 1
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
239
Functional description
tmp
= mem[accessAddress & 0xE00FFFFF, size]
mask = 1 << b
rdata = (tmp & mask) >> b
tmp
= tmp | mask
mem[accessAddress & 0xE00FFFFF, size] = tmp
//
//
//
//
//
memory read
generate bit mask
read data returned to core
modify
memory write
The cycle-by-cycle BME operations are detailed in the following table.
Table 17-6. Cycle definitions of decorated load: load-and-set 1-bit
Pipeline Stage
Cycle
x
BME AHB_ap
x+1
Forward addr to memory;
Decode decoration; Capture
address, attributes
BME AHB_dp
<previous>
x+2
Recirculate captured addr +
attr to memory as slave_wt
<next>
Perform memory read; Form
bit mask; Extract bit from
rdata; Form (rdata | mask)
and capture destination data
in register
Return extracted bit to master;
Perform write sending
registered data to memory
17.3.2.3 Decorated load unsigned bit field extract (UBFX)
This command extracts a bit field defined by LSB position (b) and the bit field width (w
+1) from the memory "container" defined by the access size associated with the load
instruction using a two-cycle read sequence.
The extracted bit field from the memory address is right-justified and zero-filled in the
operand returned to the core. Recall this is the only decorated operation that does not
perform a memory write, that is, UBFX only performs a read.
The data size is specified by the write operation and can be byte (8-bit), halfword (16-bit)
or word (32-bit). Note for the word sized operation, the maximum bit field width is 16
bits.
The use of a UBFX operation is recommended to extract a single bit. For this case, the w
field is simply set to 0, indicating a bit field width of 1.
31 30 29 28 27 26 25 24 23 22
ioubfxb 0
ioubfxh 0
ioubfxw 0
21 20 19 18 17 16 15 14 13 12
11 10
9
*
1
-
-
b
b
b
-
w
w
w
mem_addr
*
*
1
-
b
b
b
b
w
w
w
w
*
*
1
b
b
b
b
b
w
w
w
w
mem_addr
mem_addr
*
8
7
6
5
4
3
2
1
0
0
0
0
Figure 17-11. Decorated load address: unsigned bit field extract
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
240
Freescale Semiconductor, Inc.
Chapter 17 Bit Manipulation Engine (BME)
See Figure 17-11, where addr[30:29] = 01 for SRAM_U, addr[30:29] = 10 for peripheral,
addr[28] = 1 specifies the unsigned bit field extract operation, addr[27:23] is "b", the LSB
identifier, addr[22:19] is "w", the bit field width minus 1 identifier, and mem_addr[18:0]
specifies the address offset into the space based at 0x2000_0000 for SRAM_U, and
0x4000_0000 for peripheral. The "-" indicates an address bit "don't care". Note, unlike
the other decorated load operations, UBFX uses addr[19] as the least significant bit in the
"w" specifier and not as an address bit.
The decorated unsigned bit field extract read operation is defined in the following
pseudo-code as:
rdata =
ioubfx<sz>(accessAddress)
// unsigned bit field extract
tmp
= mem[accessAddress & 0xE007FFFF, size]
mask = ((1 << (w+1)) - 1) << b
rdata = (tmp & mask) >> b
// memory read
// generate bit mask
// read data returned to core
Like the BFI operation, when the starting bit position plus the field width exceeds the
container size, only part of the source bit field is extracted from the destination memory
location. Stated differently, if (b + w+1) > container_width, only the low-order
"container_width - b" bits are actually extracted. The cycle-by-cycle BME operations are
detailed in the following table.
Table 17-7. Cycle definitions of decorated load: unsigned bit field extract
Pipeline Stage
Cycle
x
BME AHB_ap
Forward addr to memory;
Decode decoration; Capture
address, attributes
BME AHB_dp
<previous>
x+1
Idle AHB address phase
x+2
<next>
Perform memory read; Form Logically right shift registered
bit mask; Form (rdata & mask) data; Return justified rdata to
and capture destination data master
in register
17.3.3 Additional details on decorated addresses and GPIO
accesses
As previously noted, the peripheral address space occupies a 516 KB region: 512 KB
based at 0x4000_0000 plus a 4 KB space based at 0x400F_F000 for GPIO accesses. This
memory layout provides compatibility with the Kinetis K Family and provides 129
address "slots", each 4 KB in size.
The GPIO address space is multiply-mapped by the hardware: it appears at the "standard"
system address 0x400F_F000 and is physically located in the address slot corresponding
to address 0x4000_F000. Decorated loads and stores create a slight complication
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
241
Application information
involving accesses to the GPIO. Recall the use of address[19] varies by decorated
operation; for AND, OR, XOR, LAC1 and LAS1, this bit functions as a true address bit,
while for BFI and UBFX, this bit defines the least significant bit of the "w" bit field
specifier.
As a result, undecorated GPIO references and decorated AND, OR, XOR, LAC1 and
LAS1 operations can use the standard 0x400F_F000 base address, while decorated BFI
and UBFX operations must use the alternate 0x4000_F000 base address. Another
implementation can simply use 0x400F_F000 as the base address for all undecorated
GPIO accesses and 0x4000_F000 as the base address for all decorated accesses. Both
implementations are supported by the hardware.
Table 17-8. Decorated peripheral and GPIO address details
Peripheral address space
Description
0x4000_0000–0x4007_FFFF
Undecorated (normal) peripheral accesses
0x4008_0000–0x400F_EFFF
Illegal addresses; attempted references are aborted and error terminated
0x400F_F000–0x400F_FFFF
Undecorated (normal) GPIO accesses using standard address
0x4010_0000–0x43FF_FFFF
Illegal addresses; attempted references are aborted and error terminated
0x4400_0000–0x4FFF_FFFF
Decorated AND, OR, XOR, LAC1, LAS1 references to peripherals and GPIO based at
either 0x4000_F000 or 0x400F_F000
0x5000_0000–0x5FFF_FFFF
Decorated BFI, UBFX references to peripherals and GPIO only based at 0x4000_F000
17.4 Application information
In this section, GNU assembler macros with C expression operands are presented as
examples of the required instructions to perform decorated operations.
This section specifically presents a partial bme.h file defining the assembly language
expressions for decorated logical stores: AND, OR, and XOR. Comparable functions for
BFI and the decorated loads are more complex and available in the complete BME header
file.
These macros use the same function names presented in Functional description.
#define IOANDW(ADDR,WDATA)
\
__asm("ldr
r3, =(1<<26);"
\
"orr
r3, %[addr];"
\
"mov
r2, %[wdata];"
\
"str
r2, [r3];"
\
:: [addr] "r" (ADDR), [wdata] "r" (WDATA) : "r2", "r3");
#define IOANDH(ADDR,WDATA)
\
__asm("ldr
r3, =(1<<26);"
\
"orr
r3, %[addr];"
\
"mov
r2, %[wdata];"
\
"strh
r2, [r3];"
\
:: [addr] "r" (ADDR), [wdata] "r" (WDATA) : "r2", "r3");
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
242
Freescale Semiconductor, Inc.
Chapter 17 Bit Manipulation Engine (BME)
#define IOANDB(ADDR,WDATA)
\
__asm("ldr
r3, =(1<<26);"
\
"orr
r3, %[addr];"
\
"mov
r2, %[wdata];"
\
"strb
r2, [r3];"
\
:: [addr] "r" (ADDR), [wdata] "r" (WDATA) : "r2", "r3");
#define IOORW(ADDR,WDATA)
\
__asm("ldr
r3, =(1<<27);"
\
"orr
r3, %[addr];"
\
"mov
r2, %[wdata];"
\
"str
r2, [r3];"
\
:: [addr] "r" (ADDR), [wdata] "r" (WDATA) : "r2", "r3");
#define IOORH(ADDR,WDATA)
\
__asm("ldr
r3, =(1<<27);"
\
"orr
r3, %[addr];"
\
"mov
r2, %[wdata];"
\
"strh
r2, [r3];"
\
:: [addr] "r" (ADDR), [wdata] "r" (WDATA) : "r2", "r3");
#define IOORB(ADDR,WDATA)
\
__asm("ldr
r3, =(1<<27);"
\
"orr
r3, %[addr];"
\
"mov
r2, %[wdata];"
\
"strb
r2, [r3];"
\
:: [addr] "r" (ADDR), [wdata] "r" (WDATA) : "r2", "r3");
#define IOXORW(ADDR,WDATA)
\
__asm("ldr
r3, =(3<<26);"
\
"orr
r3, %[addr];"
\
"mov
r2, %[wdata];"
\
"str
r2, [r3];"
\
:: [addr] "r" (ADDR), [wdata] "r" (WDATA) : "r2", "r3");
#define IOXORH(ADDR,WDATA)
\
__asm("ldr
r3, =(3<<26);"
\
"orr
r3, %[addr];"
\
"mov
r2, %[wdata];"
\
"strh
r2, [r3];"
\
:: [addr] "r" (ADDR), [wdata] "r" (WDATA) : "r2", "r3");
#define IOXORB(ADDR,WDATA)
\
__asm("ldr
r3, =(3<<26);"
\
"orr
r3, %[addr];"
\
"mov
r2, %[wdata];"
\
"strb
r2, [r3];"
\
:: [addr] "r" (ADDR), [wdata] "r" (WDATA) : "r2", "r3");
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
243
Application information
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
244
Freescale Semiconductor, Inc.
Chapter 18
Flash Memory Module (FTMRE)
18.1 Introduction
The FTMRE module implements the following:
• Program flash (flash) memory
The flash memory is ideal for single-supply applications allowing for field
reprogramming without requiring external high voltage sources for program or erase
operations. The flash module includes a memory controller that executes commands to
modify flash memory contents. The user interface to the memory controller consists of
the indexed Flash Common Command Object (FCCOB) register which is written to with
the command, global address, data, and any required command parameters. The memory
controller must complete the execution of a command before the FCCOB register can be
written to with a new command.
CAUTION
A flash byte or longword must be in the erased state before
being programmed. Cumulative programming of bits within a
flash byte or longword is not allowed.
The flash memory is read as bytes. Read access time is one bus cycle for bytes. For flash
memory, an erased bit reads 1 and a programmed bit reads 0.
18.2 Feature
18.2.1 Flash memory features
The flash memory has the following features:
• Automated program and erase algorithm with verify
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
245
Functional description
• Fast sector erase and longword program operation
• Flexible protection scheme to prevent accidental programming or erasing of flash
memory
18.2.2 Other flash module features
The flash memory module has the following other features:
• No external high-voltage power supply required for flash memory program and erase
operations
• Interrupt generation on flash command completion
• Security mechanism to prevent unauthorized access to the flash memory
18.3 Functional description
18.3.1 Modes of operation
The flash memory module provides the normal user mode of operation. The operating
mode is determined by module-level inputs and affects the FCNFG, and FCLKDIV
registers.
18.3.1.1 Wait mode
The flash memory module is not affected if the MCU enters Wait mode. The flash
module can recover the MCU from Wait via the CCIF interrupt. See Flash interrupts.
18.3.1.2 Stop mode
If a flash command is active, that is, FSTAT[CCIF] = 0, when the MCU requests Stop
mode, the current NVM operation will be completed before the MCU is allowed to enter
Stop mode.
18.3.2 Flash memory map
The MCU places the flash memory as shown in the following table.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
246
Freescale Semiconductor, Inc.
Chapter 18 Flash Memory Module (FTMRE)
MKE06Z128 contains a piece of 128 KB flash memory. This flash block is divided into
256 sectors of 512 bytes.
Table 18-1. Flash memory addressing
Device
Global address
Size (Bytes)
Description
0x0000_0000–0x0000_FFFF
64 KB
Flash block contains flash
configuration field.
0x0000_0000–0x0001_FFFF
128 KB
Flash block contains flash
configuration field.
MKE06Z64VLD4(R)
MKE06Z64VQH4(R)
MKE06Z64VLH4(R)
MKE06Z64VLK4(R)
MKE06Z128VLD4(R)
MKE06Z128VQH4(R)
MKE06Z128VLH4(R)
MKE06Z128VLK4(R)
18.3.3 Flash initialization after system reset
On each system reset, the flash module executes an initialization sequence that
establishes initial values for the flash block configuration parameters, the FPROT
protection register, and the FOPT and FSEC registers. The initialization routine reverts to
built-in default values that leave the module in a fully protected and secured state if errors
are encountered during execution of the reset sequence. If an error is detected during the
reset sequence, both FSTAT[MGSTAT] bits will be set.
FSTAT[CCIF] is cleared throughout the initialization sequence. The NVM module holds
off all CPU access for a portion of the initialization sequence. Flash reads are allowed
after the hold is removed. Completion of the initialization sequence is marked by setting
FSTAT[CCIF] high, which enables user commands. While FSTAT[CCIF] remains
cleared, it is not possible to write on registers FCCOBIX or FCCOB.
If a reset occurs while any flash command is in progress, that command will be
immediately aborted. The state of the word being programmed or the sector/block being
erased is not guaranteed.
18.3.4 Flash command operations
Flash command operations are used to modify flash memory contents.
The command operations contain three steps:
1. Configure the clock for flash program and erase command operations.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
247
Functional description
2. Use command write sequence to set flash command parameters and launch
execution.
3. Execute valid flash commands according to MCU functional mode and MCU
security state.
The figure below shows a general flowchart of the flash command write sequence.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
248
Freescale Semiconductor, Inc.
Chapter 18 Flash Memory Module (FTMRE)
START
Read: FCLKDIV
register
Clock Divider
Value Check
FDIV
Correct?
No
Read: FSTAT
register
Yes
Read: FSTAT
register
FCCOB
Availability Check
CCIF
Set?
No
NOTE: FCLKDIV must be
set after each reset
Yes
No
CCIF
Set?
Write: FCLKDIV
register
Yes
Access Error and
Protection Violation Check
ACCERR
or FPVIOL Set?
No
Results from previous Command
Yes
Write: FSTAT register
Clear ACCERR
FPVIOL 0x30
Write to FCCOBIX register
to identify specific command
parameter to load
Write to FCCOB register
to load required command
parameter
More
Parameters?
No
Yes
Write: FSTAT register
(to launch command)
Clear CCIF 0x80
Read: FSTAT register
Bit Polling for
Command Completion Check
No
CCIF Set?
Yes
END
Figure 18-1. Generic flash command write sequence flowchart
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
249
Functional description
18.3.4.1 Writing the FCLKDIV register
Prior to issuing any flash program or erase command after a reset, the user is required to
write the FCLKDIV register to divide BUSCLK down to a target FCLK of 1 MHz. The
following table shows recommended values for FCLKDIV[FDIV] based on BUSCLK
frequency.
Table 18-2. FDIV values for various BUSCLK frequencies
BUSCLK frequency
FDIV[5:0]
(MHz)
MIN1
MAX2
1.0
1.6
0x00
1.6
2.6
0x01
2.6
3.6
0x02
3.6
4.6
0x03
4.6
5.6
0x04
5.6
6.6
0x05
6.6
7.6
0x06
7.6
8.6
0x07
8.6
9.6
0x08
9.6
10.6
0x09
10.6
11.6
0x0A
11.6
12.6
0x0B
12.6
13.6
0x0C
13.6
14.6
0x0D
14.6
15.6
0x0E
15.6
16.6
0x0F
16.6
17.6
0x10
17.6
18.6
0x11
18.6
19.6
0x12
19.6
20.6
0x13
20.6
21.6
0x14
21.6
22.6
0x15
22.6
23.6
0x16
23.6
24.6
0x17
24.6
25.6
0x18
1. BUSCLK is greater than this value.
2. BUSCLK is less than or equal to this value.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
250
Freescale Semiconductor, Inc.
Chapter 18 Flash Memory Module (FTMRE)
CAUTION
Programming or erasing the flash memory cannot be performed
if the bus clock runs at less than 0.8 MHz. Setting
FCLKDIV[FDIV] too high can destroy the flash memory due to
overstress. Setting FCLKDIV[FDIV] too low can result in
incomplete programming or erasure of the flash memory cells.
When the FCLKDIV register is written, FCLKDIV[FDIVLD] is set automatically. If
FCLKDIV[FDIVLD] is 0, the FCLKDIV register has not been written since the last
reset. If the FCLKDIV register has not been written, any flash program or erase
command loaded during a command write sequence will not execute and
FSTAT[ACCERR] will be set.
18.3.4.2 Command write sequence
The memory controller will launch all valid flash commands entered using a command
write sequence.
Before launching a command, FSTAT[ACCERR] and FSTAT[FPVIOL] must be cleared
and the FSTAT[CCIF] flag will be tested to determine the status of the current command
write sequence. If FSTAT[CCIF] is 0, indicating that the previous command write
sequence is still active, a new command write sequence cannot be started and all writes to
the FCCOB register are ignored.
The FCCOB parameter fields must be loaded with all required parameters for the flash
command being executed. Access to the FCCOB parameter fields is controlled via
FCCOBIX[CCOBIX].
Flash command mode uses the indexed FCCOB register to provide a command code and
its relevant parameters to the memory controller. First, the user must set up all required
FCCOB fields. Then they can initiate the command's execution by writing a 1 to
FSTAT[CCIF]. This action clears the CCIF command completion flag to 0. When the
user clears FSTAT[CCIF], all FCCOB parameter fields are locked and cannot be changed
by the user until the command completes (evidenced by the memory controller returning
FSTAT[CCIF] to1). Some commands return information to the FCCOB register array.
The generic format for the FCCOB parameter fields in flash command mode is shown in
the following table. The return values are available for reading after the FSTAT[CCIF]
flag has been returned to 1 by the memory controller. Writes to the unimplemented
parameter fields, FCCOBIX[CCOBIX] =110b and FCCOBIX[CCOBIX] = 111b, are
ignored with read from these fields returning 0x0000.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
251
Functional description
Table 18-3 shows the generic flash command format. The high byte of the first word in
the CCOB array contains the command code, followed by the parameters for this specific
flash command. For details on the FCCOB settings required by each command, see the
flash command descriptions in Flash command summary .
Table 18-3. FCCOB – flash command mode typical usage
CCOBIX[2:0]
000
001
010
011
100
101
Byte
FCCOB parameter fields in flash command mode
HI
FCMD[7:0] defining flash command
LO
Global address [23:16]
HI
Global address [15:8]
LO
Global address [7:0]
HI
Data 0 [15:8]
LO
Data 0 [7:0]
HI
Data 1 [15:8]
LO
Data 1 [7:0]
HI
Data 2 [15:8]
LO
Data 2 [7:0]
HI
Data 3 [15:8]
LO
Data 3 [7:0]
The contents of the FCCOB parameter fields are transferred to the memory controller
when the user clears the FSTAT[CCIF] command completion flag by writing 1. The
CCIF flag will remain clear until the flash command has completed. Upon completion,
the memory controller will return FSTAT[CCIF] to 1 and the FCCOB register will be
used to communicate any results.
The following table presents the valid flash commands, as enabled by the combination of
the functional MCU mode with the MCU security state of unsecured or secured.
MCU secured state is selected by FSEC[SEC].
Table 18-4. Flash commands by mode and security state
Unsecured
Secured
U1
U2
Erase verify all blocks
*
*
0x02
Erase verify block
*
*
0x03
Erase verify flash section
*
*
0x04
Read once
*
*
0x06
Program flash
*
*
0x07
Program once
*
*
0x08
Erase all block
*
*
0x09
Erase flash block
*
*
FCMD
Command
0x01
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
252
Freescale Semiconductor, Inc.
Chapter 18 Flash Memory Module (FTMRE)
Table 18-4. Flash commands by mode and security state (continued)
Unsecured
Secured
U1
U2
Erase flash sector
*
*
0x0B
Unsecure flash
*
*
0x0C
Verify backdoor access key
*
*
0x0D
Set user margin level
*
*
0x0E
Set factory margin level
*
*
0x0F
Configure NVM
*
*
FCMD
Command
0x0A
1. Unsecured user mode
2. Secured user mode
18.3.5 Flash interrupts
The flash module can generate an interrupt when a flash command operation has
completed.
Table 18-5. Flash interrupt source
Interrupt source
Flash command complete
Interrupt flag
Local enable
CCIF
CCIE
(FSTAT register)
(FCNFG register)
Global (CCR) mask
I Bit
18.3.5.1 Description of flash interrupt operation
The flash module uses the FSTAT[CCIF] flag in combination with the FCNFG[CCIE]
interrupt enable bit to generate the flash command interrupt request.
The logic used for generating the flash module interrupts is shown in the following
figure.
CCIE
CCIF
Flash command
complete interrupt request
Figure 18-2. Flash module interrupts implementation
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
253
Functional description
18.3.6 Protection
The FPROT register can be set to protect regions in the flash memory from accidental
programing or erasing. Three separate memory regions, one growing upward from global
address 0x0000 in the flash memory, called the lower region; one growing downward
from global address 0x7FFF in the flash memory, called the higher region; and the
remaining addresses in the flash memory, can be activated for protection. The flash
memory addresses covered by these protectable regions are shown in the flash memory
map.
Default protection settings as well as security information that allows the MCU to restrict
access to the flash module are stored in the flash configuration field as described in the
table below.
Table 18-6. Flash configuration field
Global address
Size (Bytes)
0x0400–0x0407
8
Backdoor comparison key. See Verify backdoor access key command and
Unsecuring the MCU using backdoor key access.
4
Reserved
1
Flash nonvolatile byte - data[31:24]
1
Flash security byte - data[23:16]
1
Flash protection byte - data[15:8]
1
Reserved - data [7:0]
0x0408–0x040B
1
0x040C–0x040F1
Description
1. 0x0_0408–0x040B and 0x040C–0x0_040F form a flash longword in each address range and must be programmed in a
single command write sequence. Each byte in these longwords that are marked as reserved must be programmed to
0xFF. Alternatively, the Flash phrase 0x0408-0x040F can also be programmed in a single command write sequence.
The flash module provides protection to the MCU. During the reset sequence, the FPROT
register is loaded with the contents of the flash protection byte in the flash configuration
field at global address 0x040D in flash memory. The protection functions depend on the
configuration of bit settings in FPROT register.
Table 18-7. Flash protection function
FPOPEN
FPHDIS
FPLDIS
Function1
1
1
1
No flash protection
1
1
0
Protected low range
1
0
1
Protected high range
1
0
0
Protected high and low ranges
0
1
1
Full flash memory protected
0
1
0
Unprotected low range
0
0
1
Unprotected high range
0
0
0
Unprotected high and low ranges
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
254
Freescale Semiconductor, Inc.
Chapter 18 Flash Memory Module (FTMRE)
1. For range sizes, see Table 4 and Table 5
The flash protection scheme can be used by applications requiring reprogramming in
single chip mode while providing as much protection as possible if reprogramming is not
required.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
255
Functional description
FPLDIS = 0
FPHDIS = 1
FPLDIS = 0
FPHDIS = 0
7
6
5
4
3
2
1
0
FPHS[1:0]
0x0_0000
0x0_7FFF
FPOPEN = 1
Scenario
FPLDIS = 1
FPHDIS = 0
FPLS[1:0]
FPLDIS = 1
FPHDIS = 1
FPHS[1:0]
0x0_0000
0x0_7FFF
FPOPEN = 0
Scenario
FPLS[1:0]
FLASHEND
FLASHEND
Unprotected region
Protected region not defined by FPLS, FPHS
Protected region with size defined by FPHS
Protected region with size defined by FPLS
Figure 18-3. Flash protection scenarios
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
256
Freescale Semiconductor, Inc.
Chapter 18 Flash Memory Module (FTMRE)
The general guideline is that flash protection can only be added and not removed. The
following table specifies all valid transitions between flash protection scenarios. Any
attempt to write an invalid scenario to the FPROT register will be ignored. The contents
of the FPROT register reflect the active protection scenario. See the FPROT[FPHS] and
FPROT[FPLS] field descriptions for additional restrictions.
Table 18-8. Flash protection scenario transitions
To protection scenario1
From protection
scenario
0
1
2
3
0
×
×
×
×
1
×
2
4
×
4
×
×
×
×
×
×
×
×
×
×
7
×
×
7
×
3
6
6
×
×
5
5
×
×
×
×
×
×
1. Allowed transitions marked with X.
The flash protection address range is listed in the following two tables regarding the
scenarios in the table above.
Table 18-9. Flash protection higher address range
FPHS[1:0]
Global address range
Protected size
00
0x7C00–0x7FFF
1 KB
01
0x7800–0x7FFF
2 KB
10
0x7000–0x7FFF
4 KB
11
0x6000–0x7FFF
8 KB
Table 18-10. Flash protection lower address range
FPLS[1:0]
Global address range
Protected size
00
0x0000–0x07FF
2 KB
01
0x0000–0x0FFF
4 KB
10
0x0000–0x1FFF
8 KB
11
0x0000–0x3FFF
16 KB
All possible flash protection scenarios are shown in Figure 18-3. Although the protection
scheme is loaded from the flash memory at global address 0x040D during the reset
sequence, it can be changed by the user.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
257
Functional description
18.3.7 Security
The flash module provides security information to the MCU. The flash security state is
defined by FSEC[SEC]. During reset, the flash module initializes the FSEC register using
data read from the security byte of the flash configuration field. The security state out of
reset can be permanently changed by programming the security byte, assuming that the
MCU is starting from a mode where the necessary flash erase and program commands are
available and that the upper region of the flash is unprotected. If the flash security byte is
successfully programmed, its new value will take effect after the next MCU reset.
The following subsections describe these security-related subjects:
• Unsecuring the MCU using backdoor key access
• Unsecuring the MCU using SWD
• Mode and security effects on flash command availability
18.3.7.1 Unsecuring the MCU using backdoor key access
The MCU may be unsecured by using the backdoor key access feature which requires
knowledge of the contents of the backdoor keys, which are four 16-bit words
programmed at addresses 0x400–0x407. If the KEYEN[1:0] bits are in the enabled state,
the verify backdoor access key command – see Verify backdoor access key command,
allows the user to present four prospective keys for comparison to the keys stored in the
flash memory via the memory controller. If the keys presented in the verify backdoor
access key command match the backdoor keys stored in the flash memory, FSEC[SEC]
will be changed to unsecure the MCU. Key values of 0x0000 and 0xFFFF are not
permitted as backdoor keys. While the Verify Backdoor Access Key command is active,
flash memory will not be available for read access and will return invalid data.
The user code stored in the flash memory must have a method of receiving the backdoor
keys from an external stimulus. This external stimulus would typically be through one of
the on-chip serial ports.
If the KEYEN[1:0] bits are in the enabled state, the MCU can be unsecured by the
backdoor key access sequence described below:
1. Follow the command sequence for the verify backdoor access key command as
explained in Verify backdoor access key command.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
258
Freescale Semiconductor, Inc.
Chapter 18 Flash Memory Module (FTMRE)
2. If the verify backdoor access key command is successful, the MCU is unsecured and
FSEC[SEC] is forced to the unsecure state of 10.
The verify backdoor access key command is monitored by the memory controller and an
illegal key will prohibit future use of the verify backdoor access key command. A reset of
the MCU is the only method to re-enable the verify backdoor access key command. The
security as defined in the flash security byte is not changed by using the verify backdoor
access key command sequence. The backdoor keys stored in addresses 0x400–0x407 are
unaffected by the verify backdoor access key command sequence. The verify backdoor
access key command sequence has no effect on the program and erase protections
defined in the flash protection register, FPROT.
After the backdoor keys have been correctly matched, the MCU will be unsecured. After
the MCU is unsecured, the sector containing the flash security byte can be erased and the
flash security byte can be reprogrammed to the unsecure state, if desired. In the unsecure
state, the user has full control of the contents of the backdoor keys by programming
addresses 0x400–0x407 in the flash configuration field.
18.3.7.2 Unsecuring the MCU using SWD
A secured MCU can be unsecured by using the following method to erase the flash
memory:
1.
2.
3.
4.
Reset the device by asserting RESET pin or DAP_CTRL[3].
Set DAP_CTRL[0] bit to invoke debug mass erase via SWD
Release reset by deasserting RESET pin or DAP_CTRL[3] bit via SWD.
Wait till DAP_CTRL[0] bit is cleared ( After mass erase completes, DAP_CTRL[0]
bit is cleared automatically). At this time, CPU will be in hold state, MASS erase is
completed, and the device is in unsecure state (flash security byte in flash
configuration field is programmed with 0xFE) .
5. Reset the device.
18.3.7.3 Mode and security effects on flash command availability
The availability of flash module commands depends on the MCU operating mode and
security state as shown in Table 18-4.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
259
Functional description
18.3.8 Flash commands
18.3.8.1 Flash commands
The following table summarizes the valid flash commands as well as the effects of the
commands on the flash block and other resources within the flash module.
Table 18-11. Flash commands
FCMD
Command
Function on flash memory
0x01
Erase Verify All Blocks
0x02
Erase Verify Block
0x03
Erase Verify Flash Section
0x04
Read Once
0x06
Program Flash
Programs up to two longwords in a flash block
0x07
Program Once
Programs a dedicated 64 byte field in the nonvolatile information register in flash
block that is allowed to be programmed only once
Verifies that all flash blocks are erased
Verifies that a flash block is erased
Verifies that a given number of words starting at the address provided are erased
Reads a dedicated 64-byte field in the nonvolatile information register in flash
block that was previously programmed using the program once command
Erases all flash blocks
0x08
Erase All Block
An erase of all flash blocks is possible only when the FPROT[FPHDIS],
FPROT[FPLDIS] and FPROT[FPOEN] and the bit are set prior to launching the
command
Erases a flash block
0x09
Erase Flash Block
An erase of the full flash block is possible only when FPROT[FPLDIS],
FPROT[FPHDIS], and FPROT[FPOEN] are set prior to launching the command.
0x0A
Erase Flash Sector
Erases all bytes in a flash sector
0x0B
Unsecure Flash
0x0C
Verify Backdoor Access key
0x0D
Set User Margin Level
0x0E
Set Factory Margin Level
0x0F
Configure NVM
Supports a method of releasing MCU security by erasing all flash blocks and
verifying that all flash blocks are erased
Supports a method of releasing MCU security by verifying a set of security keys
Specifies a user margin read level for all flash blocks
Specifies a factory margin read level for all flash blocks
Configure NVM parameters to enable or disable some features in the NVM array,
allowing to save current/power under certain circumstances.
18.3.9 Flash command summary
This section provides details of all available flash commands launched by a command
write sequence. The FSTAT[ACCERR] will be set during the command write sequence if
any of the following illegal steps are performed, causing the command not to be
processed by the memory controller:
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
260
Freescale Semiconductor, Inc.
Chapter 18 Flash Memory Module (FTMRE)
• Starting any command write sequence that programs or erases flash memory before
initializing the FLCKDIV register.
• Writing an invalid command as part of the command write sequence.
• For additional possible errors, refer to the error handling table provided for each
command.
If a flash block is read during the execution of an algorithm (FSTAT[CCIF] = 0) on that
same block, the read operation will return invalid data. It will also trigger an illegal
access exception.
If FSTAT[ACCERR] or FSTAT[FPVIOL] are set, the user must clear these fields before
starting any command write sequence.
CAUTION
An flash longword must be in the erased state before being
programmed. Cumulative programming of bits within an flash
longword is not allowed.
18.3.9.1 Erase Verify All Blocks command
The Erase Verify All Blocks command will verify that all flash blocks have been erased.
Table 18-12. Erase Verify All Blocks command FCCOB requirements
CCOBIX[2:0]
FCCOBHI parameters
FCCOBLO parameters
000
0x01
Not required
Upon clearing FSTAT[CCIF] to launch the Erase Verify All Blocks command, the
memory controller will verify that the entire flash memory space is erased. The
FSTAT[CCIF] flag will set after the erase verify all blocks operation has completed. If all
blocks are not erased, it means blank check failed and both FSTAT[MGSTAT] bits will
be set.
Table 18-13. Erase verify all blocks command error handling
Register
Error bit
Error condition
ACCERR
Set if CCOBIX[2:0] != 000 at command launch
FPVIOL
FSTAT
None
MGSTAT1
Set if any errors have been encountered during the read1 or if blank check
failed
MGSTAT0
Set if any non-correctable errors have been encountered during the read
or if blank check failed
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
261
Functional description
1. As found in the memory map for NVM
18.3.9.2 Erase Verify Block command
The Erase Verify Block command allows the user to verify that an entire flash block has
been erased. The FCCOB global address [23:0] bits determine which block must be
verified.
Table 18-14. Erase Verify Block Command FCCOB requirements
CCOBIX[2:0]
FCCOBHI parameters
FCCOBLO parameters
000
0x02
Global address [23:16] to identify flash block
001
Global address [15:0] in flash block to be verified
Upon clearing FSTAT[CCIF] to launch the erase verify block command, the memory
controller will verify that the selected flash block is erased. The FSTAT[CCIF] flag will
set after the erase verify block operation has completed. If the block is not erased, it
means blank check failed and both FSTAT[MGSTAT] bits will be set.
Table 18-15. Erase Verify Block command error handling
Register
Error bit
ACCERR
FPVIOL
FSTAT
Error condition
Set if CCOBIX[2:0] != 000 at command launch
Set if an invalid global address [23:0] is supplied1
None
MGSTAT1
Set if any errors have been encountered during the read or if blank check
failed
MGSTAT0
Set if any non-correctable errors have been encountered during the read
or if blank check failed
1. As found in the memory map for NVM
18.3.9.3 Erase Verify Flash Section command
The Erase Verify Flash Section command will verify that a section of code in the flash
memory is erased. The Erase Verify Flash Section command defines the starting point of
the code to be verified and the number of longwords.
Table 18-16. Erase verify flash section command FCCOB requirements
CCOBIX[2:0]
FCCOBHI parameters
FCCOBLO parameters
000
0x03
Global address [23:16] of flash block
001
Global address [15:0] of the first longwords to be verified
010
Number of long words to be verified
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
262
Freescale Semiconductor, Inc.
Chapter 18 Flash Memory Module (FTMRE)
Upon clearing FSTAT[CCIF] to launch the erase verify flash section command, the
memory controller will verify that the selected section of flash memory is erased. The
FSTAT[CCIF] flag will set after the erase verify flash section operation has completed. If
the section is not erased, it means blank check failed and both FSTAT[MGSTAT] bits
will be set.
Table 18-17. Erase Verify Flash Section command error handling
Register
Error bit
Error condition
Set if CCOBIX[2:0] != 010 at command launch
Set if command not available in current mode (see Table 18-4)
ACCERR
FSTAT
Set if an invalid global address [23:0] is supplied (see Table 18-1)1
Set if a misaligned long words address is supplied (global address[1:0] !=
00)
Set if the requested section crosses flash address boundary
FPVIOL
None
MGSTAT1
Set if any errors have been encountered during the read2 or if blank check
failed
MGSTAT0
Set if any non-correctable errors have been encountered during the read2
or if blank check failed
1. As defined by the memory map for NVM
2. As found in the memory map for NVM
18.3.9.4 Read once command
The read once command provides read access to a reserved 64-byte field (8 phrase)
located in the nonvolatile information register of flash. The read once field can only be
programmed once and can not be erased. It can be used to store the product ID or any
other information that can be written only once. It is programmed using the program once
command described in Program Once command. To avoid code runaway, the read once
command must not be executed from the flash block containing the program once
reserved field.
Table 18-18. Read Once command FCCOB requirements
CCOBIX[2:0]
FCCOB parameters
000
0x04
Not required
001
Read once phrase index (0x0000 – 0x0007)
010
Read once word 0 value
011
Read once word 1 value
100
Read once word 2 value
101
Read once word 3 value
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
263
Functional description
Upon clearing FSTAT[CCIF] to launch the read once command, a read once phrase is
fetched and stored in the FCCOB indexed register. The FSTAT[CCIF] flag will set after
the read once operation has completed. Valid phrase index values for the read once
command range from 0x0000 to 0x0007. During execution of the read once command,
any attempt to read addresses within flash block will return invalid data.
Table 18-19. Read Once command error handling
Register
Error bit
Error condition
Set if CCOBIX[2:0] != 001 at command launch
ACCERR
Set if command is not available in current mode (see Table 18-4)
Set if an invalid phrase index is supplied
FSTAT
FPVIOL
None
MGSTAT1
Set if any errors have been encountered during the read
MGSTAT0
Set if any non-correctable errors have been encountered during the read
18.3.9.5 Program Flash command
The program flash operation will program up to two previously erased longwords in the
flash memory using an embedded algorithm.
Note
A flash phrase must be in the erased state before being
programmed. Cumulative programming of bits within a flash
phrase is not allowed.
Table 18-20. Program Flash command FCCOB requirements
CCOBIX[2:0]
FCCOBHI parameters
FCCOBLO parameters
000
0x06
Global address [23:16] to identify flash block
001
Global address [15:0] of longwords location to be programmed1
010
Word 0 (longword 0) program value
011
Word 1 (longword 0) program value
100
Word 2 (longword 1) program value
101
Word 3 (longword 1) program value
1. Global address [1:0] must be 00.
Upon clearing FSTAT[CCIF] to launch the Program Flash command, the memory
controller will program the data words to the supplied global address and will then
proceed to verify the data words read back as expected. The FSTAT[CCIF] flag will set
after the program flash operation has completed.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
264
Freescale Semiconductor, Inc.
Chapter 18 Flash Memory Module (FTMRE)
Table 18-21. Program Flash command error handling
Register
Error bit
Error condition
Set if CCOBIX[2:0] ≠ 011 or 101 at command launch
Set if command not available in current mode (see Table 18-4)
ACCERR
FSTAT
Set if an invalid global address [23:0] is supplied (see Table 18-1.1
Set if a misaligned longword address is supplied (global address [1:0] !=
00)
Set if the requested group of words breaches the end of the flash block.
FPVIOL
Set if the global address [23:0] points to a protected data
MGSTAT1
Set if any errors have been encountered during the verify operation
MGSTAT0
Set if any non-correctable errors have been encountered during the verify
operation
1. As defined by the memory map of NVM.
18.3.9.6 Program Once command
The Program Once command restricts programming to a reserved 64-byte field (8
phrases) in the nonvolatile information register located in flash. The program once
reserved field can be read using the read once command as described in Read once
command. The program once command must be issued only once because the nonvolatile
information register in flash cannot be erased. To avoid code runaway, the program once
command must not be executed from the flash block containing the program once
reserved field.
Table 18-22. Program Once command FCCOB requirements
CCOBIX[2:0]
FCCOB parameters
000
0x07
Not required
001
Program Once phrase index (0x000 – 0x0007)
010
Program once Word 0 value
011
Program once Word 1value
100
Program once Word 2 value
101
Program once Word 3 value
Upon clearing FSTAT[CCIF] to launch the program once command, the memory
controller first verifies that the selected phrase is erased. If erased, then the selected
phrase will be programmed and then verified with read back. The FSTAT[CCIF] flag will
remain clear, setting only after the program once operation has completed.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
265
Functional description
The reserved nonvolatile information register accessed by the Program Once command
cannot be erased, and any attempt to program one of these phrases a second time will not
be allowed. Valid phrase index values for the program once command range from 0x0000
to 0x0007. During execution of the program once command, any attempt to read
addresses within flash will return invalid data.
Table 18-23. Program Once ommand error handling
Register
Error bit
Error condition
Set if CCOBIX[2:0] != 101 at command launch
Set if command not available in current mode (see Table 18-4)
ACCERR
Set if an invalid phrase index is supplied
Set if the requested phrase has already been programmed1
FSTAT
FPVIOL
None
MGSTAT1
Set if any errors have been encountered during the verify operation
MGSTAT0
Set if any non-correctable errors have been encountered during the verify
operation
1. If a program once phrase is initially programmed to 0xFFFF_FFFF_FFFF_FFFF, the program once command will be
allowed to execute again on that same phrase.
18.3.9.7 Erase All Blocks command
The Erase All Blocks operation will erase the entire flash memory space.
Table 18-24. Erase All Blocks command FCCOB requirements
CCOBIX[2:0]
FCCOBHI parameters
FCCOBLO parameters
000
0x08
Not required
Upon clearing FSTAT[CCIF] to launch the Erase All Blocks command, the memory
controller will erase the entire NVM memory space and verify that it is erased. If the
memory controller verifies that the entire NVM memory space was properly erased,
security will be released. Therefore, the device is in unsecured state. During the execution
of this command (FSTAT[CCIF] = 0) the user must not write to any NVM module
register. The FSTAT[CCIF] flag will set after the erase all blocks operation has
completed.
Table 18-25. Erase All Blocks command error handling
Register
FSTAT
Error bit
ACCERR
FPVIOL
Error condition
Set if CCOBIX[2:0] ≠ 000 at command launch
Set if command not available in current mode (see Table 18-4)
Set if any area of the flash memory is protected
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
266
Freescale Semiconductor, Inc.
Chapter 18 Flash Memory Module (FTMRE)
Table 18-25. Erase All Blocks command error handling (continued)
Register
Error bit
Error condition
MGSTAT1
Set if any errors have been encountered during the verify operation1
MGSTAT0
Set if any non-correctable errors have been encountered during the verify
operation1
1. As found in the memory map for NVM.
18.3.9.8 Debugger mass erase request
The functionality of the Erase All Blocks command is also available in an uncommanded
fashion from the Debugger Mass Erase Request feature.
The Debugger Mass Erase request requires the clock divider register FCLKDIV to be
loaded before invoking this function. Please look into the Reference Manual for
information about the default value of FCLKDIV in case direct writes to register
FCLKDIV are not allowed by the time this feature is invoked. If FCLKDIV is not set the
Debugger Mass Erase request will not execute and the FSTAT[ACCERR] flag will set.
After the execution of the Mass Erase function, the FCLKDIV register will be reset and
the value of register FCLKDIV must be loaded before launching any other command
afterwards.
Before invoking the erase-all function, the FSTAT[ACCERR]and FSTAT[FPVIOL]
flags must be clear. When invoked the Debugger Mass Erase request will erase all flash
memory space regardless of the protection settings. If the post-erase verify passes, the
routine will then release security by setting the FSEC[SEC] to the unsecure state. The
security byte in the Flash Configuration Field will be programmed to the unsecure state.
The status of the Debugger Mass Erase request is reflected in the FCNFG[ERSAREQ].
The FCNFG[ERSAREQ] will be cleared once the operation has completed and the
normal FSTAT error reporting will be available as described in the following table.
At the end of the Mass Erase sequence Protection will remain configured as it was before
executing the Mass Erase function. If the application requires programming P-Flash after
the Mass Erase function completes, the existing protection limits must be taken into
account. If protection needs to be disabled the user may need to reset the system right
after completing the Mass Erase function.
Table 18-26. Debugger mass erase request error handling
Register
Error Bit
Error Condition
FSTAT
ACCERR
Set if command not available in current mode.
MGSTAT1
Set if any errors have been encountered during the erase verify operation,
or during the program verify operation.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
267
Functional description
Table 18-26. Debugger mass erase request error handling (continued)
Register
Error Bit
MGSTAT0
Error Condition
Set if any non-correctable errors have been encountered during the erase
verify operation, or during the program verify operation.
18.3.9.9 Erase flash block command
The erase flash block operation will erase all addresses in a flash block.
Table 18-27. Erase flash block command FCCOB requirements
CCOBIX[2:0]
000
FCCOB parameters
0x09
001
Global address [23:16] to identify flash block
Global address[15:0] in flash block to be erased
Upon clearing FSTAT[CCIF] to launch the erase flash block command, the memory
controller will erase the selected flash block and verify that it is erased. The
FSTAT[CCIF] flag will set after the erase flash block operation has completed.
Table 18-28. Erase flash block command error handling
Register
Error Bit
Error Condition
Set if CCOBIX[2:0] != 001 at command launch
ACCERR
Set if command not available in current mode (see Table 18-4)
Set if an invalid global address [23:16] is supplied1
FSTAT
FPVIOL
Set if an area of the selected flash block is protected
MGSTAT1
Set if any errors have been encountered during the verify operation2
MGSTAT0
Set if any non-correctable errors have been encountered during the verify
operation2
1. As defined by the memory map for NVM.
2. As found in the memory map for NVM.
18.3.9.10 Erase flash sector command
The erase flash sector operation will erase all addresses in a flash sector.
Table 18-29. Erase flash sector command FCCOB requirements
CCOBIX[2:0]
000
001
FCCOB parameters
0x0A
Global address [23:16] to identify flash block to be erased
Global address [15:0] anywhere within the sector to be erased. Refer to Overview for the flash
sector size
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
268
Freescale Semiconductor, Inc.
Chapter 18 Flash Memory Module (FTMRE)
Upon clearing FSTAT[CCIF] to launch the erase flash sector command, the memory
controller will erase the selected flash sector and then verify that it is erased. The
FSTAT[CCIF] flag will be set after the erase flash sector operation has completed.
Table 18-30. Erase flash sector command error handling
Register
Error bit
Error condition
Set if CCOBIX[2:0] != 001 at command launch
Set if command not available in current mode (see Table 18-4)
ACCERR
Set if an invalid global address [23:16] is supplied.1 (see Table 18-1)
Set if a misaligned longword address is supplied (global address [1:0] !=
00)
FSTAT
FPVIOL
Set if the selected flash sector is protected
MGSTAT1
Set if any errors have been encountered during the verify operation
MGSTAT0
Set if any non-correctable errors have been encountered during the verify
operation
1. As defined by the memory map for NVM
18.3.9.11 Unsecure flash command
The unsecure flash command will erase the entire flash memory space, and if the erase is
successful, will release security.
Table 18-31. Unsecure flash command FCCOB requirements
CCOBIX[2:0]
FCCOB parameters
000
0x0B
Not required
Upon clearing FSTAT[CCIF] to launch the unsecure flash command, the memory
controller will erase the entire flash memory space and verify that it is erased. If the
memory controller verifies that the entire flash memory space was properly erased,
security will be released. If the erase verify is not successful, the unsecure flash operation
sets FSTAT[MGSTAT1] and terminates without changing the security state. During the
execution of this command (FSTAT[CCIF] = 0), the user must not write to any flash
module register. The FSTAT[CCIF] flag is set after the unsecure flash operation has
completed.
Table 18-32. Unsecure flash command error handling
Register
Error bit
FSTAT
ACCERR
Error condition
Set if CCOBIX[2:0] != 000 at command launch
Set if command is not available in current mode (see Table 18-4)
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
269
Functional description
Table 18-32. Unsecure flash command error handling (continued)
Register
Error bit
Error condition
FPVIOL
Set if any area of the flash memory is protected
MGSTAT1
Set if any errors have been encountered during the verify operation1
MGSTAT0
Set if any non-correctable errors have been encountered during the verify
operation1
1. As found in the memory map for NVM
18.3.9.12 Verify backdoor access key command
The verify backdoor access key command will execute only if it is enabled by the
FSEC[KEYEN] bits. The verify backdoor access key command releases security if usersupplied keys match those stored in the flash security bytes of the flash configuration
field. See Table 18-1 for details. The code that performs verifying backdoor access
command must be running from RAM.
Table 18-33. Verify backdoor access key command FCCOB requirements
CCOBIX[2:0]
FCCOBHI parameters
000
0x0C
FCCOBLO parameters
Not required
001
Key 0
010
Key 1
011
Key 2
100
Key 3
Upon clearing FSTAT[CCIF] to launch the verify backdoor access key command, the
memory controller will check the FSEC[KEYEN] bits to verify that this command is
enabled. If not enabled, the memory controller sets the FSTAT[ACCERR] bit. If the
command is enabled, the memory controller compares the key provided in FCCOB to the
backdoor comparison key in the flash configuration field with Key 0 compared to
0x0400, and so on. If the backdoor keys match, security will be released. If the backdoor
keys do not match, security is not released and all future attempts to execute the verify
backdoor access key command are aborted (set FSTAT[ACCERR]) until a reset occurs.
The FSTAT[CCIF] flag is set after the verify backdoor access key operation has
completed.
Table 18-34. Verify backdoor access key command error handling
Register
Error bit
FSTAT
ACCERR
Error condition
Set if CCOBIX[2:0] ≠ 100 at command launch
Set if an incorrect backdoor key is supplied
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
270
Freescale Semiconductor, Inc.
Chapter 18 Flash Memory Module (FTMRE)
Table 18-34. Verify backdoor access key command error handling (continued)
Register
Error bit
Error condition
Set if backdoor key access has not been enabled (KEYEN[1:0] ≠ 10
Set if the backdoor key has mismatched since the last reset
FPVIOL
None
MGSTAT1
None
MGSTAT0
None
18.3.9.13 Set user margin level command
The user margin is a small delta to the normal read reference level and, in effect, is a
minimum safety margin. That is, if the reads pass at the tighter tolerances of the user
margins, the normal reads have at least that much safety margin before users experience
data loss.
The set user margin level command causes the memory controller to set the margin level
for future read operations of the flash block.
Table 18-35. Set user margin level command FCCOB requirements
CCOBIX[2:0]
FCCOBHI parameters
FCCOBLO parameters
000
0x0D
Global address [23:16] to identify flash block
001
Global address [15:0] to identify flash block
010
Margin level setting
Upon clearing FSTAT[CCIF] to launch the set user margin level command, the memory
controller will set the user margin level for the targeted block and then set the
FSTAT[CCIF] flag.
Note
Valid margin level settings for the set user margin level command are defined in the
following tables.
Table 18-36. Valid set user margin level settings
CCOB
Level description
(CCOBIX = 010)
0x0000
Return to normal level
0x0001
User margin-1 level1
0x0002
User margin-0 level2
1. Read margin to the erased state
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
271
Functional description
2. Read margin to the programmed state
Table 18-37. Set user margin level command error handling
Register
Error bit
Error condition
Set if CCOBIX[2:0] != 010 at command launch
ACCERR
FSTAT
Set if command is not available in current mode (see Table 18-4)
Set if an invalid global address [23:0] is supplied
Set if an invalid margin level setting is supplied
FPVIOL
None
MGSTAT1
None
MGSTAT0
None
Note
User margin levels can be used to check that NVM memory
contents have adequate margin for normal level read operations.
If unexpected results are encountered when checking NVM
memory contents at user margin levels, a potential loss of
information has been detected.
18.3.9.14 Set factory margin level command
The set factory margin Level command causes the memory controller to set the margin
level specified for future read operations of the flash block.
Table 18-38. Set factory margin level command FCCOB requirements
CCOBIX[2:0]
FCCOBHI parameters
FCCOBLO parameters
000
0x0E
Global address [23:16] to identify flash block
001
Global address [15:0] to identify flash block
010
Margin level setting
Upon clearing FSTAT[CCIF] to launch the set factory margin level command, the
memory controller will set the factory margin level for the targeted block and then set the
FSTAT[CCIF] flag.
Note
Valid margin level settings for the set factory margin level command are defined in the
following tables.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
272
Freescale Semiconductor, Inc.
Chapter 18 Flash Memory Module (FTMRE)
Table 18-39. Valid set factory margin level settings
CCOB
Level description
(CCOBIX = 010)
0x0000
Return to normal level
0x0001
User margin-1 level1
0x0002
User margin-0 level2
0x0003
Factory margin-1 level1
0x0004
Factory margin-0 level2
1. Read margin to the erased state
2. Read margin to the programmed state
Table 18-40. Set factory margin level command error handling
Register
Error bit
Error condition
Set if CCOBIX[2:0] != 010 at command launch
ACCERR
FSTAT
Set if command is not available in current mode (see Table 18-4)
Set if an invalid global address [23:0] is supplied
Set if an invalid margin level setting is supplied
FPVIOL
None
MGSTAT1
None
MGSTAT0
None
CAUTION
Factory margin levels must only be used during verify of the
initial factory programming.
Note
Factory margin levels can be used to check that Flash memory
contents have adequate margin for data retention at the normal
level setting. If unexpected results are encountered when
checking flash memory contents at factory margin levels, the
fash memory contents must be erased and reprogrammed.
18.3.9.15 Configure NVM command
The Configure NVM command allows the user to control some features in the NVM
array, enabling or disabling them with the purpose to save current/power under certain
circumstances. The settings modified with Configure NVM command are not permanent,
therefore the command must be invoked after each reset if changing these settings is
required in the user application.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
273
Functional description
Table 18-41. Configure NVM command FCCOB requirements
CCOBIX[2:0]
FCCOBHI parameters
FCCOBLO parameters
000
0x0F
Configure NVM control byte as the following table.
Table 18-42. NVM Control Byte - field descriptions
Field
7
QUERY
Description
Query / Drive Mode - This bit controls if Configure NVM command will be used to drive or to retrieve
current status of FLPHV and FLPLF bits.
0 Drive option on bits FLPHV and FLPLF into the NVM array
1 Query current status of FLPHV and FLPLF. FCCOB[0] can be read after command execution to retrieve
current status of FLPHV and FLPLV.
6-2
Reserved Bits - The RNV bits should be 1'b0, reserved for future enhancements.
RNV
1
FLPHV
Flash Low Power Control With High Supply Voltage - The FLPHV bit controls a circuit in the NVM Array
that generates an internal voltage reference to be used in Flash reads when the device is operating in the
lower range of the external supply voltage specification. Under specific circumstances this circuit can be
disabled to save power.
0 Circuit enabled (recommended, default value) - this ensures that the NVM Array will work correctly for
reads across the full range of the external supply voltage.
1 Circuit disabled - to be set only if the external voltage supply is guaranteed to drive voltage above a
minimum level.
0
FLPLF
Flash Low Power Control In Low Frequency - The FLPLF bit controls a circuit in the NVM Array that
limits current consumption during Flash reads if the device is running in low frequencies. The circuit itself
consumes some power and is recommended to be disabled for typical frequency settings. Under specific
circumstances (low bus frequency) this circuit can be enabled to save power.
0 Circuit disabled (recommended, default value1) - for typical bus frequency values this circuit can be left
disabled to minimize power consumption.
1 Circuit enabled - to be set if the bus frequency is setup to be below a minimum threshold, so the Flash
will save power while operating in low frequency.
1. Freescale might deliver parts with a different initial setting for this control in the NVM Array, eventually under a different
part number, if the part is to be used specifically in a low frequency range of operation. Therefore, if the user is not sure
about the initial setting of this control it is advisable to first run the Configure NVM command in Query mode to retrieve the
initial status of FLPLF.
LPHV controls an internal circuit that guarantees correct Flash reads across the full range
of the external voltage supply, more specifically in the lower levels of the voltage
specification. FLPHV can be used to disable this circuit if the external supply source
drives the voltage above a minimum level specified in the NVM Electrical Parameters please refer to the proper section in the Reference Manual to identify this minimum
required voltage level and the current savings in case this circuit can be disabled.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
274
Freescale Semiconductor, Inc.
Chapter 18 Flash Memory Module (FTMRE)
CAUTION
There is a risk if the user incorrectly disables the circuit
controlled by FLPHV and the operating voltage goes below the
minimum supply voltage level as specified. Under this
condition the Flash will not read meaningful data, with
unpredictable results. The only way to restore the Flash
functionality may be to reset the part, so the NVM Array will
be restored to default conditions (i.e. the circuit controlled by
FLPHV is enabled)
FLPLF controls an internal circuit that limits current consumption during Flash reads if
the Flash is running at lower bus frequencies (BUSCLK). Under typical frequency values
this circuit is recommended to be disabled to save power, but for applications that run at
low frequencies this circuit can be enabled to minimize current consumption. For details
about the threshold bus frequency value under which there can be some power savings by
enabling this circuit.
NOTE
Bit FLPLF relates to Read operations, that are affected by the
bus frequency (BUSCLK), whereas program and erase
operations are affected by the FCLK time base that is unrelated
to FLPLF.
Upon clearing CCIF to launch the Configure NVM command the MGATE will set the
NVM Array parameters accordingly (if the command is launched in Drive mode QUERY=0) and then set the CCIF flag. The current status of FLPHV and FLPLV can
always be read in FCCOB[0] after the command execution. The Configure NVM
command can be executed in Query Mode (QUERY=1) to retrieve the status of these bits
without driving them into the NVM array.
The user is not required to run the Configure NVM command for correct operation of the
Flash array. The default value after reset are the recommended / safe states for operation
of the Flash. The Configure NVM command is intended to be invoked only in conditions
where it can be used to save some power, as explained above.
Table 18-43. Configure NVM command error handling
Register
Error bit
Error condition
Set if CCOBIX[2:0] != 000 at command launch
ACCERR
FSTAT
Set if command is not available in current mode (see Table 18-4)
Set if an invalid global address [23:0] is supplied
Set if an invalid margin level setting is supplied
FPVIOL
None
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
275
Memory map and register definition
Table 18-43. Configure NVM command error handling (continued)
Register
Error bit
Error condition
MGSTAT1
None
MGSTAT0
None
18.4 Memory map and register definition
This section presents a high-level summary of the registers and how they are mapped.
The registers can be accessed in 32-bits, 16-bits (aligned on data[31:16] or on data[15:0])
or 8-bits. In the case of the writable registers, the write accesses are forbidden during
flash command execution. For more details, see Caution note in Flash memory map.
FTMRE memory map
Absolute
address
(hex)
Width
Access
(in bits)
Register name
Reset value
Section/
page
4002_0001
Flash CCOB Index Register (FTMRE_FCCOBIX)
8
R/W
00h
18.4.1/276
4002_0002
Flash Security Register (FTMRE_FSEC)
8
R
Undefined
18.4.2/277
4002_0003
Flash Clock Divider Register (FTMRE_FCLKDIV)
8
R/W
00h
18.4.3/278
4002_0005
Flash Status Register (FTMRE_FSTAT)
8
R/W
80h
18.4.4/279
4002_0007
Flash Configuration Register (FTMRE_FCNFG)
8
R/W
00h
18.4.5/280
4002_0008
Flash Common Command Object Register: Low
(FTMRE_FCCOBLO)
8
R/W
00h
18.4.6/281
4002_0009
Flash Common Command Object Register:High
(FTMRE_FCCOBHI)
8
R/W
00h
18.4.7/281
4002_000B
Flash Protection Register (FTMRE_FPROT)
8
R
See section
18.4.8/281
4002_000F
Flash Option Register (FTMRE_FOPT)
8
R
Undefined
18.4.9/283
18.4.1 Flash CCOB Index Register (FTMRE_FCCOBIX)
The FCCOBIX register is used to index the FCCOB register for NVM memory
operations.
Address: 4002_0000h base + 1h offset = 4002_0001h
Bit
Read
Write
Reset
7
6
5
4
3
2
1
0
0
0
0
0
CCOBIX
0
0
0
0
0
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
276
Freescale Semiconductor, Inc.
Chapter 18 Flash Memory Module (FTMRE)
FTMRE_FCCOBIX field descriptions
Field
Description
7–3
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
CCOBIX
Common Command Register Index
Selects which word of the FCCOB register array is being read or written to.
18.4.2 Flash Security Register (FTMRE_FSEC)
The FSEC register holds all bits associated with the security of the MCU and NVM
module. All fields in the FSEC register are readable but not writable. During the reset
sequence, the FSEC register is loaded with the contents of the flash security byte in the
flash configuration field located in flash memory.
See Security for security function.
Address: 4002_0000h base + 2h offset = 4002_0002h
Bit
7
Read
6
5
4
KEYEN
3
2
1
Reserved
0
SEC
Write
Reset
x*
x*
x*
x*
x*
x*
x*
x*
* Notes:
• x = Undefined at reset.
FTMRE_FSEC field descriptions
Field
7–6
KEYEN
Description
Backdoor Key Security Enable Bits
The KEYEN[1:0] bits define the enabling of backdoor key access to the flash module.
NOTE: 01 is the preferred KEYEN state to disable backdoor key access.
00
01
10
11
5–2
Reserved
SEC
Disabled
Disabled
Enabled
Disabled
This field is reserved.
Flash Security Bits
Defines the security state of the MCU. If the flash module is unsecured using backdoor key access, the
SEC field is forced to 10.
NOTE: 01 is the preferred SEC state to set MCU to secured state.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
277
Memory map and register definition
FTMRE_FSEC field descriptions (continued)
Field
Description
00
01
10
11
Secured
Secured
Unsecured
Secured
18.4.3 Flash Clock Divider Register (FTMRE_FCLKDIV)
The FCLKDIV register is used to control timed events in program and erase algorithms.
NOTE
The FCLKDIV register must not be written while a flash
command is executing (FSTAT[CCIF] = 0)
Address: 4002_0000h base + 3h offset = 4002_0003h
Bit
Read
7
FDIVLD
Write
Reset
6
0
5
4
3
FDIVLCK
0
2
1
0
0
0
0
FDIV
0
0
0
FTMRE_FCLKDIV field descriptions
Field
Description
7
FDIVLD
Clock Divider Loaded
6
FDIVLCK
Clock Divider Locked
FDIV
0
1
0
1
FCLKDIV register has not been written since the last reset.
FCLKDIV register has been written since the last reset.
FDIV field is open for writing.
FDIV value is locked and cannot be changed. After the lock bit is set high, only reset can clear this bit
and restore writability to the FDIV field in user mode.
Clock Divider Bits
FDIV[5:0] must be set to effectively divide BUSCLK down to 1MHz to control timed events during flash
program and erase algorithms. Refer to the table in the Writing the FCLKDIV register for the
recommended values of FDIV based on the BUSCLK frequency.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
278
Freescale Semiconductor, Inc.
Chapter 18 Flash Memory Module (FTMRE)
18.4.4 Flash Status Register (FTMRE_FSTAT)
The FSTAT register reports the operational status of the flash module.
Address: 4002_0000h base + 5h offset = 4002_0005h
Bit
Read
Write
Reset
7
6
0
CCIF
1
0
5
4
ACCERR
FPVIOL
0
0
3
2
MGBUSY
0
0
0
1
0
MGSTAT
0
0
FTMRE_FSTAT field descriptions
Field
7
CCIF
Description
Command Complete Interrupt Flag
Indicates that a flash command has completed. The CCIF flag is cleared by writing a 1 to CCIF to launch a
command and CCIF will stay low until command completion or command violation.
0
1
Flash command is in progress.
Flash command has completed.
6
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
5
ACCERR
Flash Access Error Flag
Indicates an illegal access has occurred to the flash memory caused by either a violation of the command
write sequence or issuing an illegal flash command. While ACCERR is set, the CCIF flag cannot be
cleared to launch a command. Writing 1 to this field clears it while writing a 0 to this field has no effect.
0
1
4
FPVIOL
Flash Protection Violation Flag
Indicates an attempt was made to program or erase an address in a protected area of flash memory
during a command write sequence. Writing 1 to FPVIOL clears this field while writing 0 to this field has no
effect. While FPIOL is set, it is not possible to launch a command or start a command write sequence.
0
1
3
MGBUSY
No access error is detected.
Access error is detected.
No protection violation is detected.
Protection violation is detected.
Memory Controller Busy Flag
Reflects the active state of the memory controller.
0
1
Memory controller is idle.
Memory controller is busy executing a flash command (CCIF = 0).
2
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
MGSTAT
Memory Controller Command Completion Status Flag
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
279
Memory map and register definition
FTMRE_FSTAT field descriptions (continued)
Field
Description
One or more MGSTAT flag bits are set if an error is detected during execution of a flash command or
during the flash reset sequence.
NOTE: Reset value can deviate from the value shown if a double bit fault is detected during the reset
sequence.
18.4.5 Flash Configuration Register (FTMRE_FCNFG)
The FCNFG register enables the flash command complete interrupt and forces ECC
faults on flash array read access from the CPU.
Address: 4002_0000h base + 7h offset = 4002_0007h
Bit
Read
Write
Reset
7
CCIE
0
6
5
0
ERSAREQ
0
0
4
3
2
1
0
0
0
0
0
0
0
FTMRE_FCNFG field descriptions
Field
7
CCIE
Description
Command Complete Interrupt Enable
Controls interrupt generation when a flash command has completed.
0
1
6
Reserved
5
ERSAREQ
Command complete interrupt is disabled.
An interrupt will be requested whenever the CCIF flag in the FSTAT register is set.
This field is reserved.
This read-only field is reserved and always has the value 0.
Debugger Mass Erase Request
Requests the MGATE to execute the Erase All Blocks command and release security. ERSAREQ is not
directly writable but is under indirect user control.
The ERSAREQ field sets to 1 when the MGATE starts executing the sequence. ERSAREQ will be reset to
0 by the MGATE when the operation is completed
0
1
Reserved
No request or request complete
Request to
• run the Erase All Blocks command
• verify the erased state
• program the security byte in the Flash Configuration Field to the unsecure state
• release MCU security by setting FSEC[SEC] to the unsecure state
This field is reserved.
This read-only field is reserved and always has the value 0.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
280
Freescale Semiconductor, Inc.
Chapter 18 Flash Memory Module (FTMRE)
18.4.6 Flash Common Command Object Register: Low
(FTMRE_FCCOBLO)
The FCCOB is an array of six words addressed via the CCOBIX index found in the
FCCOBIX register. Byte-wide reads and writes are allowed to the FCCOB register.
Address: 4002_0000h base + 8h offset = 4002_0008h
Bit
Read
Write
Reset
7
6
5
4
3
2
1
0
0
0
0
0
CCOB
0
0
0
0
FTMRE_FCCOBLO field descriptions
Field
CCOB
Description
Common Command Object Bit 7:0
Low 8 bits of Common Command Object register
18.4.7 Flash Common Command Object Register:High
(FTMRE_FCCOBHI)
The FCCOB is an array of six words addressed via the CCOBIX index found in the
FCCOBIX register. Byte-wide reads and writes are allowed to the FCCOB register.
Address: 4002_0000h base + 9h offset = 4002_0009h
Bit
Read
Write
Reset
7
6
5
4
3
2
1
0
0
0
0
0
CCOB
0
0
0
0
FTMRE_FCCOBHI field descriptions
Field
CCOB
Description
Common Command Object Bit 15:8
High 8 bits of Common Command Object register
18.4.8 Flash Protection Register (FTMRE_FPROT)
The FPROT register defines which flash sectors are protected against program and erase
operations.
The unreserved bits of the FPROT register are writable with the restriction that the size of
the protected region can only be increased (see Protection).
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
281
Memory map and register definition
During the reset sequence, the FPROT register is loaded with the contents of the flash
protection byte in the flash configuration field at global address 0x40D located in flash
memory. To change the flash protection that will be loaded during the reset sequence, the
upper sector of the flash memory must be unprotected, then the flash protection byte must
be reprogrammed.
Trying to alter data in any protected area in the flash memory will result in a protection
violation error and the FPVIOL bit will be set in the FSTAT register. The block erase of a
flash block is not possible if any of the flash sectors contained in the same flash block are
protected.
Address: 4002_0000h base + Bh offset = 4002_000Bh
Bit
Read
Write
Reset
7
6
FPOPEN
*
5
RNV6
4
3
FPHDIS
*
*
FPHS
*
2
1
FPLDIS
*
0
FPLS
*
*
*
* Notes:
•
FTMRE_FPROT field descriptions
Field
7
FPOPEN
Description
Flash Protection Operation Enable
The FPOPEN bit determines the protection function for program or erase operations.
0
1
6
RNV6
5
FPHDIS
Reserved Nonvolatile Bit
The RNV bit must remain in the erased state.
Flash Protection Higher Address Range Disable
The FPHDIS bit determines whether there is a protected/unprotected area in a specific region of the flash
memory ending with global address 0x7FFF.
0
1
4–3
FPHS
2
FPLDIS
When FPOPEN is clear, the FPHDIS and FPLDIS fields define unprotected address ranges as
specified by the corresponding FPHS and FPLS fields.
When FPOPEN is set, the FPHDIS and FPLDIS fields enable protection for the address range
specified by the corresponding FPHS and FPLS fields.
Protection/Unprotection enabled.
Protection/Unprotection disabled.
Flash Protection Higher Address Size
The FPHS bits determine the size of the protected/unprotected area in flash memory. The FPHS bits can
be written to only while the FPHDIS bit is set.
Flash Protection Lower Address Range Disable
The FPLDIS bit determines whether there is a protected/unprotected area in a specific region of the flash
memory beginning with global address 0x0_0000.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
282
Freescale Semiconductor, Inc.
Chapter 18 Flash Memory Module (FTMRE)
FTMRE_FPROT field descriptions (continued)
Field
Description
0
1
FPLS
Protection/Unprotection enabled.
Protection/Unprotection disabled.
Flash Protection Lower Address Size
The FPLS bits determine the size of the protected/unprotected area in flash memory. The FPLS bits can
only be written to while the FPLDIS bit is set.
18.4.9 Flash Option Register (FTMRE_FOPT)
The FOPT register is the flash option register.
During the reset sequence, the FOPT register is loaded from the flash nonvolatile byte in
the flash configuration field at global address 0x040F located in flash memory as
indicated by reset condition.
Address: 4002_0000h base + Fh offset = 4002_000Fh
Bit
7
6
5
4
Read
3
2
1
0
x*
x*
x*
x*
NV
Write
Reset
x*
x*
x*
x*
* Notes:
• x = Undefined at reset.
FTMRE_FOPT field descriptions
Field
NV
Description
Nonvolatile Bits
The NV[7:0] bits are available as nonvolatile bits. During the reset sequence, the FOPT register is loaded
from the flash nonvolatile byte in the flash configuration field at global address 0x40F located in flash
memory.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
283
Memory map and register definition
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
284
Freescale Semiconductor, Inc.
Chapter 19
Flash Memory Controller (FMC)
19.1 Introduction
The Flash Memory Controller (FMC) is a memory acceleration unit. A list of features
provided by the FMC can be found here.
• an interface between bus masters and the 32-bit program flash memory.
• a buffer and a cache that can accelerate program flash memory data transfers.
19.1.1 Overview
The Flash Memory Controller manages the interface between bus masters and the 32-bit
program flash memory. The FMC receives status information detailing the configuration
of the flash memory and uses this information to ensure a proper interface. The FMC
supports 8-bit, 16-bit, and 32-bit read operations from the program flash memory. A write
operation to program flash memory results in a bus error.
In addition, the FMC provides two separate mechanisms for accelerating the interface
between bus masters and program flash memory. A 32-bit speculation buffer can prefetch
the next 32-bit flash memory location, and a 4-way, 2-set program flash memory cache
can store previously accessed program flash memory data for quick access times.
19.1.2 Features
The features of FMC module include:
• Interface between bus masters and the 32-bit program flash memory:
• 8-bit, 16-bit, and 32-bit read operations to nonvolatile flash memory.
• Acceleration of data transfer from the program flash memory to the device:
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
285
Modes of operation
• 32-bit prefetch speculation buffer for program flash accesses with controls for
instruction/data access
• 4-way, 2-set, 32-bit line size program flash memory cache for a total of eight 32bit entries with invalidation control
19.2 Modes of operation
The FMC operates only when a bus master accesses the program flash memory.
In terms of chip power modes:
• The FMC operates only in Run and Wait modes.
• For any power mode where the program flash memory cannot be accessed, the FMC
is disabled.
19.3 External signal description
The FMC has no external (off-chip) signals.
19.4 Memory map and register descriptions
The MCM's programming model provides control and configuration of the FMC's
features.
For details, see the description of the MCM's Platform Control Register (PLACR).
19.5 Functional description
The FMC is a flash acceleration unit with flexible buffers for user configuration.
Besides managing the interface between bus masters and the program flash memory, the
FMC can be used to customize the program flash memory cache and buffer to provide
single-cycle system clock data access times. Whenever a hit occurs for the prefetch
speculation buffer or the cache (when enabled), the requested data is transferred within a
single system clock.
Upon system reset, the FMC is configured as follows:
• Flash cache is enabled.
• Instruction speculation and caching are enabled.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
286
Freescale Semiconductor, Inc.
Chapter 19 Flash Memory Controller (FMC)
• Data speculation is disabled.
• Data caching is enabled.
Though the default configuration provides flash acceleration, advanced users may desire
to customize the FMC buffer configurations to maximize throughput for their use cases.
For example, the user may adjust the controls to enable buffering per access type (data or
instruction).
NOTE
When reconfiguring the FMC, do not program the control and
configuration inputs to the FMC while the program flash
memory is being accessed. Instead, change them with a routine
executing from RAM in supervisor mode.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
287
Functional description
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
288
Freescale Semiconductor, Inc.
Chapter 20
Internal Clock Source (ICS)
20.1 Introduction
The internal clock source (ICS) module provides clock source choices for the MCU. The
module contains a frequency-locked loop (FLL) as a clock source that is controllable by
either an internal or an external reference clock. The module can provide this FLL clock
or either of the internal or external reference clocks as a source for the MCU system
clock. There are also signals provided to control a low-power oscillator (OSC) module.
These signals configure and enable the OSC module to generate its external crystal/
resonator clock (OSC_OUT) used by peripheral modules and as the ICS external
reference clock source. The ICS external reference clock can be the external crystal/
resonator (OSC_OUT) supplied by an OSC, or it can be another external clock source.
The ICS clock source chosen is passed through a reduced bus divider (BDIV) which
allows a lower final output clock frequency to be derived.
20.1.1 Features
The key features of the ICS module are given below:
• Frequency-locked loop (FLL) is trimmable for accuracy
• Internal or external reference clocks can be used to control the FLL.
• Reference divider is provided for external clock.
• Internal reference clock has 9 trim bits available.
• Internal or external reference clocks can be selected as the clock source for the MCU.
• Whichever clock is selected as the source can be divided down.
• 3-bit select for clock divider is provided
• Allowable dividers are: 1, 2, 4, 8, 16, 32, 64, 128 if OSC_CR[RANGE] = 0; 32,
64, 128, 256, 512, 1024 if OSC_CR[RANGE] = 1.
• FLL Engaged Internal mode is automatically selected out of reset.
• Selectable digitally-controlled oscillators (DCO) optimized frequency ranges
• FLL lock detector and external clock monitor
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
289
Introduction
• FLL lock detector with interrupt capability
• External reference clock monitor with reset capability
• Digitally controlled oscillators optimized for 40-48 MHz frequency range
20.1.2 Block diagram
The following figure is the ICS block diagram.
External Reference Clock /
Oscillator
Internal Clock Source Block
ICSIRCLK
IRCLKEN
IREFSTEN
BDIV
Internal
Reference
Clock
/ 2n
n=0-7
ICSOUT
LP
CLKS
FLL
SCFTRIMSCTRIM
/ 2n
n=0-7
Filter DCO
IREFS
RDIV
ICSFFCLK
IREFST
CLKST
LOLIE
LOLS
LOCK
CME
Figure 20-1. Internal clock source (ICS) block diagram
20.1.3 Modes of operation
There are seven modes of operation for the ICS: FEI, FEE, FBI, FBILP, FBE, FBELP,
and STOP. Each of these modes is explained briefly in the following subsections.
20.1.3.1 FLL engaged internal (FEI)
In FLL engaged internal mode, which is the default mode, the ICS supplies a clock
derived from the FLL which is controlled by the internal reference clock.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
290
Freescale Semiconductor, Inc.
Chapter 20 Internal Clock Source (ICS)
20.1.3.2 FLL engaged external (FEE)
In FLL engaged external mode, the ICS supplies a clock derived from the FLL which is
controlled by an external reference clock source.
20.1.3.3 FLL bypassed internal (FBI)
In FLL bypassed internal mode, the FLL is enabled and controlled by the internal
reference clock, but is bypassed. The ICS supplies a clock derived from the internal
reference clock.
20.1.3.4 FLL bypassed internal low power (FBILP)
In FLL bypassed internal low power mode, the FLL is disabled and bypassed, and the
ICS supplies a clock derived from the internal reference clock.
20.1.3.5 FLL bypassed external (FBE)
In FLL bypassed external mode, the FLL is enabled and controlled by an external
reference clock, but is bypassed. The ICS supplies a clock derived from the external
reference clock source.
20.1.3.6 FLL bypassed external low power (FBELP)
In FLL bypassed external low power mode, the FLL is disabled and bypassed, and the
ICS supplies a clock derived from the external reference clock.
20.1.3.7 Stop (STOP)
In Stop mode, the FLL is disabled and the internal or the ICS external reference clocks
source (OSC_OUT) can be selected to be enabled or disabled. The ICS does not provide
any MCU clock sources.
NOTE
The DCO frequency changes from the pre-stop value to its reset
value and the FLL needs to reacquire the lock before the
frequency is stable. Timing sensitive operations must wait for
the FLL acquisition time, tAcquire, before executing.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
291
External signal description
20.2 External signal description
There are no ICS signals that connect off chip.
20.3 Register definition
ICS memory map
Absolute
address
(hex)
Width
Access
(in bits)
Register name
Reset value
Section/
page
4006_4000
ICS Control Register 1 (ICS_C1)
8
R/W
04h
20.3.1/292
4006_4001
ICS Control Register 2 (ICS_C2)
8
R/W
20h
20.3.2/293
4006_4002
ICS Control Register 3 (ICS_C3)
8
R/W
Undefined
20.3.3/294
4006_4003
ICS Control Register 4 (ICS_C4)
8
R/W
See section
20.3.4/295
4006_4004
ICS Status Register (ICS_S)
8
R
10h
20.3.5/295
2
1
0
IREFS
IRCLKEN
IREFSTEN
1
0
0
20.3.1 ICS Control Register 1 (ICS_C1)
Address: 4006_4000h base + 0h offset = 4006_4000h
Bit
Read
Write
Reset
7
6
5
CLKS
0
4
3
RDIV
0
0
0
0
ICS_C1 field descriptions
Field
7–6
CLKS
Description
Clock Source Select
Selects the clock source that controls the bus frequency. The actual bus frequency depends on the value
of ICS_C2[BDIV].
00
01
10
11
5–3
RDIV
Output of FLL is selected.
Internal reference clock is selected.
External reference clock is selected.
Reserved, defaults to 00.
Reference Divider
Selects the amount to divide down the FLL reference clock selected by the IREFS bits. Resulting
frequency must be in the range 31.25 kHz to 39.0625 kHz.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
292
Freescale Semiconductor, Inc.
Chapter 20 Internal Clock Source (ICS)
ICS_C1 field descriptions (continued)
Field
Description
RDIV
OSC_CR[RANGE ]= 0
OSC_CR[RANGE ]= 1
000
11
32
001
2
64
010
4
128
011
8
256
100
16
512
101
32
1024
110
64
Reserved
111
128
Reserved
1. Reset default
2
IREFS
Internal Reference Select
Selects the reference clock source for the FLL.
0
1
1
IRCLKEN
Internal Reference Clock Enable
Enables the internal reference clock for use as ICSIRCLK.
0
1
0
IREFSTEN
External reference clock is selected.
Internal reference clock is selected.
ICSIRCLK is inactive.
ICSIRCLK is active.
Internal Reference Stop Enable
Controls whether or not the internal reference clock remains enabled when the ICS enters Stop mode.
0
1
Internal reference clock is disabled in Stop mode.
Internal reference clock stays enabled in Stop mode if IRCLKEN is set, or if ICS is in FEI, FBI, or
FBILP mode before entering Stop.
1. Reset default
20.3.2 ICS Control Register 2 (ICS_C2)
Address: 4006_4000h base + 1h offset = 4006_4001h
Bit
Read
Write
Reset
7
6
5
BDIV
0
0
4
3
2
LP
1
0
1
0
0
0
0
0
0
ICS_C2 field descriptions
Field
7–5
BDIV
Description
Bus Frequency Divider
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
293
Register definition
ICS_C2 field descriptions (continued)
Field
Description
Selects the amount to divide down the clock source selected by ICS_C1[CLKS]. This controls the bus
frequency.
000
001
010
011
100
101
110
111
4
LP
Encoding 0—Divides the selected clock by 1.
Encoding 1—Divides the selected clock by 2 (reset default).
Encoding 2—Divides the selected clock by 4.
Encoding 3—Divides the selected clock by 8.
Encoding 4—Divides the selected clock by 16.
Encoding 5—Divides the selected clock by 32.
Encoding 6—Divides the selected clock by 64.
Encoding 7—Divides the selected clock by 128.
Low Power Select
Controls whether the FLL is disabled in FLL bypassed modes.
0
1
Reserved
FLL is not disabled in bypass mode.
FLL is disabled in bypass modes unless debug is active.
This field is reserved.
This read-only field is reserved and always has the value 0.
20.3.3 ICS Control Register 3 (ICS_C3)
Address: 4006_4000h base + 2h offset = 4006_4002h
Bit
Read
Write
Reset
7
6
5
4
3
2
1
0
x*
x*
x*
x*
SCTRIM
x*
x*
x*
x*
* Notes:
• x = Undefined at reset.
ICS_C3 field descriptions
Field
SCTRIM
Description
Slow Internal Reference Clock Trim Setting
Controls the slow internal reference clock frequency by controlling the internal reference clock period. The
bits are binary weighted. In other words, bit 1 adjusts twice as much as bit 0. Increasing the binary value in
SCTRIM will increase the period, and decreasing the value will decrease the period. An additional fine trim
bit is available as the ICS_C4[SCFTRIM]. SCTRIM is loaded during reset from a factory programmed
location if the device is not in any debug mode.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
294
Freescale Semiconductor, Inc.
Chapter 20 Internal Clock Source (ICS)
20.3.4 ICS Control Register 4 (ICS_C4)
Address: 4006_4000h base + 3h offset = 4006_4003h
Bit
Read
Write
Reset
7
6
5
LOLIE
0
CME
0
0
0
4
3
2
1
0
0
0
0
SCFTRIM
0
0
x*
* Notes:
• x = Undefined at reset.
ICS_C4 field descriptions
Field
7
LOLIE
Description
Loss of Lock Interrupt
Determines if an interrupt request is made following a loss of lock indication. This field has an effect only
when ICS_S[LOLS] is set.
0
1
6
Reserved
5
CME
No request on loss of lock.
Generates an interrupt request on loss of lock.
This field is reserved.
This read-only field is reserved and always has the value 0.
Clock Monitor Enable
Determines if a reset request is made following a loss of external clock indication. This field must be set to
a logic 1 only when the ICS is in an operational mode that uses the external clock (FEE, FBE, or FBELP).
0
1
Clock monitor is disabled.
Generates a reset request on loss of external clock.
4–1
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
0
SCFTRIM
Slow Internal Reference Clock Fine Trim
Controls the smallest adjustment of the internal reference clock frequency. Setting SCFTRIM will increase
the period and clearing SCFTRIM will decrease the period by the smallest amount possible.
NOTE: SCFTRIM is loaded during reset from a factory programmed location when not in any debug
mode.
20.3.5 ICS Status Register (ICS_S)
Address: 4006_4000h base + 4h offset = 4006_4004h
Bit
7
6
5
4
Read
LOLS
LOCK
0
IREFST
Write
w1c
Reset
0
0
0
1
3
2
1
CLKST
0
0
0
0
0
0
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
295
Functional description
ICS_S field descriptions
Field
7
LOLS
Description
Loss of Lock Status
Indicates the lock status for the FLL. LOLS is set when lock detection is enabled and after acquiring lock,
the FLL output frequency has fallen outside the lock exit frequency tolerance, from ±4.7% to ±5.97%.
ICS_C4[LOLIE] determines whether an interrupt request is made when set. LOLS is cleared by reset or by
writing a logic 1 to LOLS when LOLS is set. Writing a logic 0 to LOLS has no effect.
0
1
6
LOCK
Lock Status
Indicates whether the FLL has acquired lock. Lock detection is disabled when FLL is disabled. If the lock
status bit is set then changing the value of any of the following fields IREFS, RDIV[2:0], or, if in FEI or FBI
modes, TRIM[7:0] will cause the lock status bit to clear and stay cleared until the FLL has reacquired lock.
Stop mode entry will also cause the lock status bit to clear and stay cleared until the FLL has reacquired
lock.
0
1
5
Reserved
4
IREFST
Internal Reference Status
Indicates the current source for the reference clock. This field does not update immediately after a write to
ICS_C1[IREFS] due to internal synchronization between clock domains.
Source of reference clock is external clock.
Source of reference clock is internal clock.
Clock Mode Status
Indicates the current clock mode. This field doesn't update immediately after a write to ICS_C1[CLKS] due
to internal synchronization between clock domains.
00
01
10
11
Reserved
FLL is currently unlocked.
FLL is currently locked.
This field is reserved.
This read-only field is reserved and always has the value 0.
0
1
3–2
CLKST
FLL has not lost lock since LOLS was last cleared.
FLL has lost lock since LOLS was last cleared.
Output of FLL is selected.
FLL Bypassed, internal reference clock is selected.
FLL Bypassed, external reference clock is selected.
Reserved.
This field is reserved.
This read-only field is reserved and always has the value 0.
20.4 Functional description
20.4.1 Operational modes
The seven states of the ICS are shown as a state diagram and are described below. The
arrows indicate the allowed movements among the states.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
296
Freescale Semiconductor, Inc.
Chapter 20 Internal Clock Source (ICS)
IREFS=1
CLKS=00
IREFS=0
CLKS=10
Debug Enabled
or LP =0
FLL Bypassed
External Low
Power(FBELP)
FLL Engaged
Internal (FEI)
FLL Bypassed
External (FBE)
IREFS=0
CLKS=10
Debug Disabled
and LP=1
IREFS=1
CLKS=01
Debug Enabled
or LP=0
FLL Bypassed
Internal (FBI)
FLL Bypassed
Internal Low
Power(FBILP)
IREFS=1
CLKS=01
Debug Disabled
and LP=1
FLL Engaged
External (FEE)
IREFS=0
CLKS=00
Entered from any state
when MCU enters stop
Stop
Returns to state that was active
before MCU entered stop, unless
RESET occurs while in stop.
Figure 20-7. Clock switching modes
20.4.1.1 FLL engaged internal (FEI)
FLL engaged internal (FEI) is the default mode of operation and is entered when all the
following conditions occur:
• 00b is written to ICS_C1[CLKS].
• 1b is written to ICS_C1[IREFS].
In FLL engaged internal mode, the ICSOUT clock is derived from the FLL clock, which
is controlled by the internal reference clock. The FLL loop locks the frequency to 1280
times the internal reference frequency. The internal reference clock is enabled.
20.4.1.2 FLL engaged external (FEE)
The FLL engaged external (FEE) mode is entered when all the following conditions
occur:
• 00b is written to ICS_C1[CLKS].
• 0b is written to ICS_C1[IREFS].
• ICS_C1[RDIV] and and OSC_CR[RANGE ] are written to divide external reference
clock to be within the range of 31.25 kHz to 39.0625 kHz.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
297
Functional description
In FLL engaged external mode, the ICSOUT clock is derived from the FLL clock which
is controlled by the external reference clock source.The FLL loop locks the frequency to
1280 times the external reference frequency, as selected by ICS_C1[RDIV] and
OSC_CR[RANGE ]. The external reference clock is enabled.
20.4.1.3 FLL bypassed internal (FBI)
The FLL bypassed internal (FBI) mode is entered when all the following conditions
occur:
• 01b is written to ICS_C1[CLKS].
• 1b is written to ICS_C1[IREFS].
In FLL bypassed internal mode, the ICSOUT clock is derived from the internal reference
clock. The FLL clock is controlled by the internal reference clock, and the FLL loop
locks the FLL frequency to 1280 times the internal reference frequency. The internal
reference clock is enabled.
20.4.1.4 FLL bypassed internal low power (FBILP)
The FLL bypassed internal low power (FBILP) mode is entered when all the following
conditions occur:
• 01b is written to ICS_C1[CLKS].
• 1b is written to ICS_C1[IREFS].
In FLL bypassed internal low-power mode, the ICSOUT clock is derived from the
internal reference clock and the FLL is disabled. The internal reference clock is enabled.
20.4.1.5 FLL bypassed external (FBE)
The FLL bypassed external (FBE) mode is entered when all the following conditions
occur:
• 10b is written to ICS_C1[CLKS].
• 0b is written to ICS_C1[IREFS].
• ICS_C1[RDIV] and OSC_CR[RANGE ] fields are written to divide external
reference clock to be within the range of 31.25 kHz to 39.0625 kHz.
In FLL bypassed external mode, the ICSOUT clock is derived from the external reference
clock source. The FLL clock is controlled by the external reference clock, and the FLL
loop locks the FLL frequency to 1280 times the external reference frequency, as selected
by ICS_C1[RDIV] and OSC_CR[RANGE ].
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
298
Freescale Semiconductor, Inc.
Chapter 20 Internal Clock Source (ICS)
20.4.1.6 FLL bypassed external low power (FBELP)
The FLL bypassed external low-power (FBELP) mode is entered when all the following
conditions occur:
• 10b is written to ICS_C1[CLKS].
• 0b is written to ICS_C1[IREFS].
In FLL bypassed external low-power mode, the ICSOUT clock is derived from the
external reference clock source and the FLL is disabled. The external reference clock
source is enabled.
20.4.1.7 Stop
NOTE
The DCO frequency changes from the pre-stop value to its reset
value and the FLL need to re-acquire the lock before the
frequency is stable. Timing sensitive operations must wait for
the FLL acquisition time, tAcquire, before executing.
Stop mode is entered whenever the MCU enters a STOP state. In this mode, all ICS clock
signals are static except in the following cases:
ICSIRCLK will be active in Stop mode when all the following conditions occur:
• 1b is written to ICS_C1[IRCLKEN].
• 1b is written to ICS_C1[IREFSTEN].
20.4.2 Mode switching
ICS_C1[IREFS] can be changed at anytime, but the actual switch to the newly selected
clock is shown by ICS_S[IREFST]. When switching between FLL engaged internal (FEI)
and FLL engaged external (FEE) modes, the FLL begins locking again after the switch is
completed.
ICS_C1[CLKS] can also be changed at anytime, but the actual switch to the newly
selected clock is shown by ICS_S[CLKST]. If the newly selected clock is not available,
the previous clock remains selected.
NOTE
When mode switching is from FEE, FBE or FBELP to FEI, it is
suggested to wait IREFST switch completion, then change
ICS_C1[CLKS].
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
299
Functional description
20.4.3 Bus frequency divider
ICS_C2[BDIV] can be changed anytime and the actual switch to the new frequency
occurs immediately.
20.4.4 Low-power field usage
The Low-Power (LP) field in the ICS_C2 register is provided to allow the FLL to be
disabled and thus conserve power when it is not being used.
However, in some applications it may be desirable to allow the FLL to be enabled and to
lock for maximum accuracy before switching to an FLL engaged mode. To do this, write
0b to ICS_C2[LP].
20.4.5 Internal reference clock
When ICS_C1[IRCLKEN] is set, the internal reference clock signal is presented as
ICSIRCLK, which can be used as an additional clock source. To re-target the ICSIRCLK
frequency, write a new value to the ICS_C3[SCTRIM] bits to trim the period of the
internal reference clock:
• Writing a larger value slows down the ICSIRCLK frequency.
• Writing a smaller value to the ICS_C3 register speeds up the ICSIRCLK frequency.
The TRIM bits effect the ICSOUT frequency if the ICS is in FLL engaged internal (FEI),
FLL bypassed internal (FBI), or FLL bypassed internal low power (FBILP) mode.
Until ICSIRCLK is trimmed, programming low bus divider (ICS_C2[BDIV]) factors
may result in ICSOUT frequencies that exceed the maximum chip-level frequency and
violate the chip-level clock timing specifications.
If ICS_C1[IREFSTEN] is set and 1b is written to ICS_C1[IRCLKEN], the internal
reference clock keeps running during Stop mode in order to provide a fast recovery upon
exiting Stop mode.
All MCU devices are factory programmed with a trim value in a reserved memory
location. This value is uploaded to the ICS_C3 register and ICS_C4[SCFTRIM] during
any reset initialization. For finer precision, trim the internal oscillator in the application
and set ICS_C4[SCFTRIM] accordingly.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
300
Freescale Semiconductor, Inc.
Chapter 20 Internal Clock Source (ICS)
20.4.6 Fixed frequency clock
The ICS presents the divided FLL reference clock as ICSFFCLK for use as an additional
clock source. ICSFFCLK frequency must be no more than 1/4 of the ICSOUT frequency
to be valid. Because of this requirement, in bypass modes, the ICSFFCLK is valid only in
bypass external modes (FBE and FBELP) for the following conditions of
ICS_C2[BDIV], and divider factor of ICS_C1[RDIV] and OSC_CR[RANGE ] values:
if OSC_CR[RANGE ] is high,
• ICS_C2[BDIV] = 000, ICS_C2[RDIV] ≥ 010
• ICS_C2[BDIV] = 001 (divide by 2), ICS_C2[RDIV] ≥ 011
• ICS_C2[BDIV] = 010 (divide by 4), ICS_C2[RDIV] ≥ 100
• ICS_C2[BDIV] = 011 (divide by 8), ICS_C2[RDIV] ≥ 101
20.4.7 FLL lock and clock monitor
20.4.7.1 FLL clock lock
In FBE and FEE modes, the clock detector source uses the external reference as the
reference. When FLL is detected from lock to unlock, ICS_S[LOLS] is set. An interrupt
will be generated if ICS_C4[LOLIE] is set. ICS_S[LOLS] is cleared by reset or by
writing a logic 1 to ICS_S[LOLS] when ICS_S[LOLS] is set. Writing a logic 0 to
ICS_S[LOLS] has no effect.
In FBI and FEI modes, the lock detector source uses the internal reference as the
reference. When FLL is detected from lock to unlock, ICS_S[LOLS] is set. An interrupt
will be generated if ICS_C4[LOLIE] is set. ICS_S[LOLS] is cleared by reset or by
writing a logic 1 to ICS_S[LOLS] when ICS_S[LOLS] is set. Writing a logic 0 to
ICS_S[LOLS] has no effect.
In FBELP and FBILP modes, the FLL is not on so that lock detect function is not
applicable.
20.4.7.2 External reference clock monitor
In FBE, FEE, or FBELP modes, if 1 is written to ICS_C4[CME], the clock monitor is
enabled. If the external reference falls below a certain frequency, the MCU will reset.
The SIM_SRSID[LOC] will be set to indicate the error.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
301
Initialization/application information
20.5 Initialization/application information
This section provides example code to give some basic direction to a user on how to
initialize and configure the ICS module. The example software is implemented in C
language.
20.5.1 Initializing FEI mode
The following code segment demonstrates setting ICS to FEI mode.
Example: 20.5.1.1 FEI mode initialization routine
/* the
ICS_C2
ICS_C1
ICS_C3
/* the
ICS_C2
ICS_C1
ICS_C3
following code segment demonstrates setting ICS to FEI mode generating 36MHz bus*/
= 0x00; /*BDIV=0, no prescalar
= 0x04; /* internal reference clock to FLL */
= TRIM_VALUE_35.15625KHZ; /* FLL output 36MHz */
following code segment demonstrates setting ICS to FEI mode generating 4.5MHz bus*/
= 0x60; /*BDIV=3, prescalar = 8 */
= 0x04; /* internal reference clock to FLL */
= TRIM_VALUE_35.15625KHZ; /* FLL output 4.5MHz */
20.5.2 Initializing FBI mode
The following code segment demonstrates setting ICS to FBI mode.
Example: 20.5.2.1 FBI mode initialization routine
/* the
bus*/
ICS_C2
ICS_C1
ICS_C3
following code segment demonstrates setting ICS to FBI mode generating 32768Hz
= 0x00; /*BDIV=0, no prescalar
= 0x44;
= TRIM_VALUE_32K768HZ;
20.5.3 Initializing FEE mode
The following code segment demonstrates setting ICS to FEE mode.
Example: 20.5.3.1 FEE mode initialization routine
/* the following code segment demonstrates setting ICS to FEE mode generating 32.768MHZ bus*/
/* supposing external 32.768K crystal is installed */
OSC_CR = 0xB0; /* enable oscillator with low power mode */
ICS_C2 = 0x00; /* BDIV=0, no prescalar/
while ((OSC_CR & OSC_CR_OSCINIT_MASK) == 0); /* waiting until oscillator is ready */
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
302
Freescale Semiconductor, Inc.
Chapter 20 Internal Clock Source (ICS)
ICS_C1 = 0x80; /* external clock reference (32.768kHz) to FLL, RDIV = 0, external prescalar
= 0 */
20.5.4 Initializing FBE mode
The following code segment demonstrates setting ICS to FBE mode.
Example: 20.5.4.1 FBE mode initialization routine
/* the following code segment demonstrates setting ICS to FBE mode generating 20MHZ bus*/
/* supposing external 20MHZ crystal is installed */
OSC_CR = 0xA6; /* enable clock in high range, high gain mode */
ICS_C2 = 0x00; /* BDIV=0, no prescalar*/
ICS_C1 = 0x80; /* external clock reference (20MHZ) to FLL output */
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
303
Initialization/application information
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
304
Freescale Semiconductor, Inc.
Chapter 21
Oscillator (OSC)
21.1 Introduction
21.1.1 Overview
The OSC module provides the clock source for the MCU. The OSC module, in
conjunction with an external crystal or resonator, generates a clock for the MCU that can
be used as reference clock or bus clock.
21.1.2 Features and modes
Key features of the OSC module are:
• Supports 32 kHz crystals (low range mode)
• Supports 4–24 MHz crystals and resonators (high range mode)
• Automatic gain control (AGC) to optimize power consumption in both frequency
ranges using low-power mode (low gain mode)
• High gain option in both frequency ranges: 32 kHz, 4–24 MHz
• Voltage and frequency filtering to guarantee clock frequency and stability
• Supports to be enabled by ICS.
21.1.3 Block diagram
See the following figure for OSC module block diagram.
The OSC module uses a crystal or resonator to generate three filtered oscillator clock
signals(XTL_CLK). The XTL_CLK can work in Stop mode since they come from Hard
block which always has power.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
305
Signal description
The OSCOS decides whether OSC_OUT comes from internal oscillators(XTL_CLK) or
directly from external clock driven on EXTAL pin. The OSCOS signal allows the XTAL
pad to be used as I/O or test clock.
EXTAL
XTAL
Digital Wrapper
Mux
OSC_OUT
HGO
High Gain
32 k/4-24 MHz
Oscillator
RANGE
XTL_CLK
OSCOS
EN
Low Power
4-24 MHz
Oscillator
ICS_OSC_EN
EN
Low Power
32 kHz
Oscillator
STOP
OSCEN
4096
Counter
OSCSTEN
CNT_DONE_4096
OSC_INIT
HARD BLOCK
Figure 21-1. OSC module block diagram
21.2 Signal description
The following table shows the user-accessible signals available for the OSC module. See
the chip-level specification to find out which signals are actually connected to external
pins.
Table 21-1. OSC signal descriptions
Signal
EXTAL
XTAL
Description
I/O
External clock/oscillator input
Analog input
Oscillator output
Analog output
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
306
Freescale Semiconductor, Inc.
Chapter 21 Oscillator (OSC)
21.3 External crystal / resonator connections
The connections for a crystal/resonator frequency reference are shown in Figure 21-2 and
Figure 21-3. When using low-frequency, low-power mode, the only external component
is the crystal or resonator itself. In the other oscillator modes, load capacitors (Cx, Cy)
and feedback resistor (RF) are required. In addition, a series resistor (RS) may be used in
high-gain modes. Recommended component values are listed in the data sheet.
Table 21-2. External crystal/resonator connections
Oscillator mode
Connections
Low frequency, high gain
Connection2
Low frequency, low-power
Connection1
High frequency, high gain (4–20 MHz)
Connection2
High frequency, low-power (4–20 MHz)
Connection2
VLP Oscillator (OSC_VLP) Module
XTAL
VSS
EXTAL
Crystal or Resonator
Figure 21-2. Crystal/resonator connections - connection 1
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
307
External clock connections
VLP Oscillator (OSC_VLP) Module
VSS
XTAL
EXTAL
RS
Cy
Cx
RF
Crystal or Resonator
Figure 21-3. Crystal/resonator connections - connection 2
21.4 External clock connections
In external clock mode (OSC_CR[OSCOS] = 0), the pins can be connected as shown in
the following figure.
VLP Oscillator (OSC_VLP) Module
XTAL
GPIO
VSS
EXTAL
External Clock Input
Figure 21-4. External clock connections
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
308
Freescale Semiconductor, Inc.
Chapter 21 Oscillator (OSC)
21.5 Memory map and register descriptions
OSC memory map
Absolute
address
(hex)
4006_5000
Width
Access
(in bits)
Register name
OSC Control Register (OSC_CR)
8
Reset value
Section/
page
00h
21.5.1/309
2
1
0
RANGE
HGO
0
0
R/W
21.5.1 OSC Control Register (OSC_CR)
Address: 4006_5000h base + 0h offset = 4006_5000h
Bit
Read
Write
Reset
7
6
0
OSCEN
0
5
4
OSCSTEN
OSCOS
0
0
0
3
0
0
OSCINIT
0
OSC_CR field descriptions
Field
7
OSCEN
Description
OSC Enable
Enables the OSC module. The OSC module can also be enabled by the ICS module.
0
1
OSC module is disabled.
OSC module is enabled.
6
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
5
OSCSTEN
OSC Enable in Stop mode
Controls whether or not the OSC clock remains enabled when MCU enters Stop mode and OSCEN is set.
OSCSTEN has no effect if ICS requests OSC enable.
0
1
4
OSCOS
OSC Output Select
Selects the output clock of the OSC module.
0
1
3
Reserved
2
RANGE
OSC clock is disabled in Stop mode.
OSC clock stays enabled in Stop mode.
External clock source from EXTAL pin is selected.
Oscillator clock source is selected.
This field is reserved.
This read-only field is reserved and always has the value 0.
Frequency Range Select
Selects the frequency range for the OSC module.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
309
Functional description
OSC_CR field descriptions (continued)
Field
Description
0
1
1
HGO
High Gain Oscillator Select
Controls the OSC mode of operation.
0
1
0
OSCINIT
Low frequency range of 32 kHz.
High frequency range of 4–24 MHz.
Low-power mode
High-gain mode
OSC Initialization
This field is set after the initialization cycles of oscillator are completed.
0
1
Oscillator initialization is not complete.
Oscillator initialization is completed.
21.6 Functional description
21.6.1 OSC module states
There are three states of the OSC module. A state diagram is shown in Figure 21-6. The
states and the transitions among each other are described in this section.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
310
Freescale Semiconductor, Inc.
Chapter 21 Oscillator (OSC)
Off
• Oscillator OFF
• OSC_OUT = Static
EN
EN
&& OSCOS
EN
&& OSCOS
Start-Up
Start-Up
• Oscillator On
• OSC_OUT = EXTAL
• Oscillator On, not yet stable
• OSC_OUT = Static
CNT_DONE_4096
Stable
• Oscillator On, Stable
• OSC_OUT = XTL_CLK
Figure 21-6. OSC module state diagram
EN is decided by OSC_CR[OSCEN], Stop, OSC_CR[OSCSTEN], and external request
(ICS_OSC_EN). See the following table for details.
Table 21-5. EN status
EN
ICS_OSC_EN
OSC_CR[OSCEN]
OSC_CR[OSCSTEN]
Stop
1
1
-
-
-
1
0
1
-
0
1
0
1
1
1
0
0
1
0
1
0
0
0
-
-
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
311
Functional description
21.6.1.1 Off
The off state is entered whenever the EN signal is negated. Upon entering this state,
XTL_CLK and OSC_OUT is static. The EXTAL and XTAL pins are also decoupled
from all other oscillator circuitry in this state. The OSC module circuitry is configured to
draw minimal current.
21.6.1.2 Oscillator startup
The oscillator startup state is entered whenever the oscillator is first enabled (EN
transitions high) and OSC_CR[OSCOS] is high. In this state, the OSC module is enabled
and oscillations are starting up, but have not yet stabilized. When the oscillation
amplitude becomes large enough to pass through the input buffer, XTL_CLK begins
clocking the counter. When the counter has seen 4096 cycles of XTL_CLK, the oscillator
is considered stable and XTL_CLK is passed to the output clock OSC_OUT.
21.6.1.3 Oscillator stable
The oscillator stable state is entered whenever the oscillator is enabled (EN is high),
OSC_CR[OSCOS] is high, and the counter has seen 4096 cycles of XTL_CLK
(CNT_DONE_4096 is high). In this state, the OSC module is producing a stable output
clock on OSC_OUT. Its frequency is determined by the external components being used.
21.6.1.4 External clock mode
The external clock state is entered when the oscillator is enabled(EN is high) and
OSC_CR[OSCOS] is low. In this state, the OSC module is set up to buffer (with
hysteresis) a clock from EXTAL onto the OSC_OUT. Its frequency is determined by the
external clock being supplied.
21.6.2 OSC module modes
The oscillator is a Pierce-type oscillator that supports external crystals or resonators
operating over the frequency ranges shown in the following table. These modes assume
EN = 1, OSC_CR[OSCOS] = 1.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
312
Freescale Semiconductor, Inc.
Chapter 21 Oscillator (OSC)
Table 21-6. Oscillator modes
RANGE
HGO
Mode
Frequency range
0
1
Low-frequency, high-gain
flo(min) up to flo(max)
0
0
Low-frequency, low-power
(VLP)
1
1
High-frequency mode1, highgain
1
0
High-frequency mode1, lowpower
fhi(min) up to fhi(max)
21.6.2.1 Low-frequency, high-gain mode
In low-frequency, high-gain mode (OSC_CR[RANGE] = 0, OSC_CR[HGO] = 1) the
oscillator uses a simple inverter-style amplifier. The gain is set to achieve rail-to-rail
oscillation amplitudes. The oscillator input buffer in this mode is single-ended. It
provides low pass frequency filtering as well as hysteresis for voltage filtering and
converts the output to logic levels.
21.6.2.2 Low-frequency, low-power mode
In low-frequency, low-power mode (OSC_CR[RANGE] = 0, OSC_CR[HGO] = 0), the
oscillator uses a gain control loop to minimize power consumption. As the oscillation
amplitude increases, the amplifier current is reduced. This continues until a desired
amplitude is achieved at steady-state.
The oscillator input buffer in this mode is single-ended. It provides low pass frequency
filtering as well as hysteresis for voltage filtering and converts the output to logic levels.
In this mode, the amplifier inputs, gain-control input, and input buffer input are all
capacitively coupled for leakage tolerance (not sensitive to the DC level of EXTAL).
Also in this mode, all external components except for the resonator itself are integrated,
which includes the load capacitors and feeback resistor which biases EXTAL.
21.6.2.3 High-frequency, high-gain mode
In high-frequency, high-gain Mode (OSC_CR[RANGE] = 1, OSC_CR[HGO] = 1), the
oscillator uses a simple inverter-style amplifier. The gain is set to achieve rail-to-rail
oscillation amplitudes.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
313
Functional description
The oscillator input buffer in this mode is single-ended. It provides low pass frequency
filtering as well as hysteresis for voltage filtering and converts the output to logic levels.
21.6.2.4 High-frequency, low-power mode
In high-frequency, low-power mode (OSC_CR[RANGE] = 1, OSC_CR[HGO] = 0) the
oscillator uses a gain control loop to minimize power consumption. As the oscillation
amplitude increases, the amplifier current is reduced. This continues until a desired
amplitude is achieved at steady-state.
The oscillator input buffer in this mode is differential. It provides low pass frequency
filtering as well as hysteresis for voltage filtering and converts the output to logic levels.
21.6.3 Counter
The oscillator output clock (OSC_OUT) is gated off until the counter has detected 4096
cycles of its input clock (XTL_CLK). Once 4096 cycles are complete, the counter passes
XTL_CLK onto OSC_OUT. This counting timeout is used to guarantee output clock
stability.
21.6.4 Reference clock pin requirements
The OSC module requires use of both the EXTAL and XTAL pins to generate an output
clock in oscillator mode but requires only the EXTAL pin in external clock mode. The
EXTAL and XTAL pins can be used for I/O or test clock purposes as long as the
specifications listed in the data sheet are met.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
314
Freescale Semiconductor, Inc.
Chapter 22
Cyclic Redundancy Check (CRC)
22.1 Introduction
NOTE
For the chip-specific implementation details of this module's
instances, see the chip configuration information.
The cyclic redundancy check (CRC) module generates 16/32-bit CRC code for error
detection.
The CRC module provides a programmable polynomial, WAS, and other parameters
required to implement a 16-bit or 32-bit CRC standard.
The 16/32-bit code is calculated for 32 bits of data at a time.
22.1.1 Features
Features of the CRC module include:
• Hardware CRC generator circuit using a 16-bit or 32-bit programmable shift register
• Programmable initial seed value and polynomial
• Option to transpose input data or output data (the CRC result) bitwise or bytewise.
This option is required for certain CRC standards. A bytewise transpose operation is
not possible when accessing the CRC data register via 8-bit accesses. In this case, the
user's software must perform the bytewise transpose function.
• Option for inversion of final CRC result
• 32-bit CPU register programming interface
22.1.2 Block diagram
The following is a block diagram of the CRC.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
315
Memory map and register descriptions
TOT
WAS
FXOR
TOTR
CRC Data Register
Reverse
Logic
Seed
MUX
[31:24][
23:16]
[15:8]
[7:0]
NOT
Logic
CRC Data
Reverse
Logic
Checksum
CRC Polynomial
Register
[31:24]
[23:16]
[15:8]
[7:0]
CRC Data Register
[31:24]
[23:16]
[15:8]
[7:0]
CRC Engine
Data
Combine
Logic
Polynomial
16-/32-bit Select
TCRC
Figure 22-1. Programmable cyclic redundancy check (CRC) block diagram
22.1.3 Modes of operation
Various MCU modes affect the CRC module's functionality.
22.1.3.1 Run mode
This is the basic mode of operation.
22.1.3.2 Low-power modes (Wait or Stop)
Any CRC calculation in progress stops when the MCU enters a low-power mode that
disables the module clock. It resumes after the clock is enabled or via the system reset for
exiting the low-power mode. Clock gating for this module is dependent on the MCU.
22.2 Memory map and register descriptions
CRC memory map
Absolute
address
(hex)
Register name
Width
Access
(in bits)
Reset value
Section/
page
4003_2000
CRC Data register (CRC_DATA)
32
R/W
FFFF_FFFFh
22.2.1/317
4003_2004
CRC Polynomial register (CRC_GPOLY)
32
R/W
0000_1021h
22.2.2/318
4003_2008
CRC Control register (CRC_CTRL)
32
R/W
0000_0000h
22.2.3/318
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
316
Freescale Semiconductor, Inc.
Chapter 22 Cyclic Redundancy Check (CRC)
22.2.1 CRC Data register (CRC_DATA)
The CRC Data register contains the value of the seed, data, and checksum. When
CTRL[WAS] is set, any write to the data register is regarded as the seed value. When
CTRL[WAS] is cleared, any write to the data register is regarded as data for general CRC
computation.
In 16-bit CRC mode, the HU and HL fields are not used for programming the seed value,
and reads of these fields return an indeterminate value. In 32-bit CRC mode, all fields are
used for programming the seed value.
When programming data values, the values can be written 8 bits, 16 bits, or 32 bits at a
time, provided all bytes are contiguous; with MSB of data value written first.
After all data values are written, the CRC result can be read from this data register. In 16bit CRC mode, the CRC result is available in the LU and LL fields. In 32-bit CRC mode,
all fields contain the result. Reads of this register at any time return the intermediate CRC
value, provided the CRC module is configured.
Address: 4003_2000h base + 0h offset = 4003_2000h
Bit
R
W
31
Reset
1
30
29
28
27
26
25
24
23
22
21
HU
1
1
1
1
20
19
18
17
16
15
14
13
HL
1
1
1
1
1
1
1
1
12
11
10
9
8
7
6
5
4
LU
1
1
1
1
1
1
1
1
3
2
1
0
1
1
1
1
LL
1
1
1
1
1
1
1
CRC_DATA field descriptions
Field
Description
31–24
HU
CRC High Upper Byte
23–16
HL
CRC High Lower Byte
15–8
LU
CRC Low Upper Byte
LL
CRC Low Lower Byte
In 16-bit CRC mode (CTRL[TCRC] is 0), this field is not used for programming a seed value. In 32-bit CRC
mode (CTRL[TCRC] is 1), values written to this field are part of the seed value when CTRL[WAS] is 1.
When CTRL[WAS] is 0, data written to this field is used for CRC checksum generation in both 16-bit and
32-bit CRC modes.
In 16-bit CRC mode (CTRL[TCRC] is 0), this field is not used for programming a seed value. In 32-bit CRC
mode (CTRL[TCRC] is 1), values written to this field are part of the seed value when CTRL[WAS] is 1.
When CTRL[WAS] is 0, data written to this field is used for CRC checksum generation in both 16-bit and
32-bit CRC modes.
When CTRL[WAS] is 1, values written to this field are part of the seed value. When CTRL[WAS] is 0, data
written to this field is used for CRC checksum generation.
When CTRL[WAS] is 1, values written to this field are part of the seed value. When CTRL[WAS] is 0, data
written to this field is used for CRC checksum generation.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
317
Memory map and register descriptions
22.2.2 CRC Polynomial register (CRC_GPOLY)
This register contains the value of the polynomial for the CRC calculation. The HIGH
field contains the upper 16 bits of the CRC polynomial, which are used only in 32-bit
CRC mode. Writes to the HIGH field are ignored in 16-bit CRC mode. The LOW field
contains the lower 16 bits of the CRC polynomial, which are used in both 16- and 32-bit
CRC modes.
Address: 4003_2000h base + 4h offset = 4003_2004h
Bit
R
W
31
Reset
0
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
HIGH
0
0
0
0
0
0
0
0
8
7
6
5
4
3
2
1
0
0
1
0
0
0
0
1
LOW
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
CRC_GPOLY field descriptions
Field
Description
31–16
HIGH
High Polynominal Half-word
LOW
Low Polynominal Half-word
Writable and readable in 32-bit CRC mode (CTRL[TCRC] is 1). This field is not writable in 16-bit CRC
mode (CTRL[TCRC] is 0).
Writable and readable in both 32-bit and 16-bit CRC modes.
22.2.3 CRC Control register (CRC_CTRL)
This register controls the configuration and working of the CRC module. Appropriate bits
must be set before starting a new CRC calculation. A new CRC calculation is initialized
by asserting CTRL[WAS] and then writing the seed into the CRC data register.
Address: 4003_2000h base + 8h offset = 4003_2008h
31
30
29
28
27
26
25
0
R
TOT
TOTR
FXOR WAS
W
24
23
22
21
20
19
18
17
16
0
TCRC
Bit
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
0
0
0
0
0
0
0
0
0
R
W
Reset
0
0
0
0
0
0
0
0
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
318
Freescale Semiconductor, Inc.
Chapter 22 Cyclic Redundancy Check (CRC)
CRC_CTRL field descriptions
Field
31–30
TOT
Description
Type Of Transpose For Writes
Defines the transpose configuration of the data written to the CRC data register. See the description of the
transpose feature for the available transpose options.
00
01
10
11
29–28
TOTR
Type Of Transpose For Read
Identifies the transpose configuration of the value read from the CRC Data register. See the description of
the transpose feature for the available transpose options.
00
01
10
11
27
Reserved
26
FXOR
Complement Read Of CRC Data Register
Some CRC protocols require the final checksum to be XORed with 0xFFFFFFFF or 0xFFFF. Asserting
this bit enables on the fly complementing of read data.
Reserved
No XOR on reading.
Invert or complement the read value of the CRC Data register.
Write CRC Data Register As Seed
When asserted, a value written to the CRC data register is considered a seed value. When deasserted, a
value written to the CRC data register is taken as data for CRC computation.
0
1
24
TCRC
No transposition.
Bits in bytes are transposed; bytes are not transposed.
Both bits in bytes and bytes are transposed.
Only bytes are transposed; no bits in a byte are transposed.
This field is reserved.
This read-only field is reserved and always has the value 0.
0
1
25
WAS
No transposition.
Bits in bytes are transposed; bytes are not transposed.
Both bits in bytes and bytes are transposed.
Only bytes are transposed; no bits in a byte are transposed.
Writes to the CRC data register are data values.
Writes to the CRC data register are seed values.
Width of CRC protocol.
0
1
16-bit CRC protocol.
32-bit CRC protocol.
This field is reserved.
This read-only field is reserved and always has the value 0.
22.3 Functional description
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
319
Functional description
22.3.1 CRC initialization/reinitialization
To enable the CRC calculation, the user must program CRC_CTRL[WAS],
CRC_GPOLY, necessary parameters for transposition and CRC result inversion in the
applicable registers. Asserting CRC_CTRL[WAS] enables the programming of the seed
value into the CRC_DATA register.
After a completed CRC calculation, reasserting CRC_CTRL[WAS] and programming a
seed, whether the value is new or a previously used seed value, reinitialize the CRC
module for a new CRC computation. All other parameters must be set before
programming the seed value and subsequent data values.
22.3.2 CRC calculations
In 16-bit and 32-bit CRC modes, data values can be programmed 8 bits, 16 bits, or 32 bits
at a time, provided all bytes are contiguous. Noncontiguous bytes can lead to an incorrect
CRC computation.
22.3.2.1 16-bit CRC
To compute a 16-bit CRC:
1. Clear CRC_CTRL[TCRC] to enable 16-bit CRC mode.
2. Program the transpose and complement options in the CTRL register as required for
the CRC calculation. See Transpose feature and CRC result complement for details.
3. Write a 16-bit polynomial to the CRC_GPOLY[LOW] field. The
CRC_GPOLY[HIGH] field is not usable in 16-bit CRC mode.
4. Set CRC_CTRL[WAS] to program the seed value.
5. Write a 16-bit seed to CRC_DATA[LU:LL]. CRC_DATA[HU:HL] are not used.
6. Clear CRC_CTRL[WAS] to start writing data values.
7. Write data values into CRC_DATA[HU:HL:LU:LL]. A CRC is computed on every
data value write, and the intermediate CRC result is stored back into
CRC_DATA[LU:LL].
8. When all values have been written, read the final CRC result from
CRC_DATA[LU:LL].
Transpose and complement operations are performed on the fly while reading or writing
values. See Transpose feature and CRC result complement for details.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
320
Freescale Semiconductor, Inc.
Chapter 22 Cyclic Redundancy Check (CRC)
22.3.2.2 32-bit CRC
To compute a 32-bit CRC:
1. Set CRC_CTRL[TCRC] to enable 32-bit CRC mode.
2. Program the transpose and complement options in the CTRL register as required for
the CRC calculation. See Transpose feature and CRC result complement for details.
3. Write a 32-bit polynomial to CRC_GPOLY[HIGH:LOW].
4. Set CRC_CTRL[WAS] to program the seed value.
5. Write a 32-bit seed to CRC_DATA[HU:HL:LU:LL].
6. Clear CRC_CTRL[WAS] to start writing data values.
7. Write data values into CRC_DATA[HU:HL:LU:LL]. A CRC is computed on every
data value write, and the intermediate CRC result is stored back into
CRC_DATA[HU:HL:LU:LL].
8. When all values have been written, read the final CRC result from
CRC_DATA[HU:HL:LU:LL]. The CRC is calculated bytewise, and two clocks are
required to complete one CRC calculation.
Transpose and complement operations are performed on the fly while reading or writing
values. See Transpose feature and CRC result complement for details.
22.3.3 Transpose feature
By default, the transpose feature is not enabled. However, some CRC standards require
the input data and/or the final checksum to be transposed. The user software has the
option to configure each transpose operation separately, as desired by the CRC standard.
The data is transposed on the fly while being read or written.
Some protocols use little endian format for the data stream to calculate a CRC. In this
case, the transpose feature usefully flips the bits. This transpose option is one of the types
supported by the CRC module.
22.3.3.1 Types of transpose
The CRC module provides several types of transpose functions to flip the bits and/or
bytes, for both writing input data and reading the CRC result, separately using the
CTRL[TOT] or CTRL[TOTR] fields, according to the CRC calculation being used.
The following types of transpose functions are available for writing to and reading from
the CRC data register:
1. CTRL[TOT] or CTRL[TOTR] is 00.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
321
Functional description
No transposition occurs.
2. CTRL[TOT] or CTRL[TOTR] is 01
Bits in a byte are transposed, while bytes are not transposed.
reg[31:0] becomes {reg[24:31], reg[16:23], reg[8:15], reg[0:7]}
31
24
23
16
15
24
31
16
23
8
8
7
0
15
0
7
Figure 22-5. Transpose type 01
3. CTRL[TOT] or CTRL[TOTR] is 10.
Both bits in bytes and bytes are transposed.
reg[31:0] becomes = {reg[0:7], reg[8:15],reg[16:23], reg[24:31]}
31
0
31
0
Figure 22-6. Transpose type 10
4. CTRL[TOT] or CTRL[TOTR] is 11.
Bytes are transposed, but bits are not transposed.
reg[31:0] becomes {reg[7:0], reg[15:8], reg[23:16], reg[31:24]}
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
322
Freescale Semiconductor, Inc.
Chapter 22 Cyclic Redundancy Check (CRC)
31
7
24
23
16
15
8
0
15
8
23
16
7
31
0
24
Figure 22-7. Transpose type 11
NOTE
For 8-bit and 16-bit write accesses to the CRC data register, the
data is transposed with zeros on the unused byte or bytes
(taking 32 bits as a whole), but the CRC is calculated on the
valid byte(s) only. When reading the CRC data register for a
16-bit CRC result and using transpose options 10 and 11, the
resulting value after transposition resides in the CRC[HU:HL]
fields. The user software must account for this situation when
reading the 16-bit CRC result, so reading 32 bits is preferred.
22.3.4 CRC result complement
When CTRL[FXOR] is set, the checksum is complemented. The CRC result complement
function outputs the complement of the checksum value stored in the CRC data register
every time the CRC data register is read. When CTRL[FXOR] is cleared, reading the
CRC data register accesses the raw checksum value.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
323
Functional description
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
324
Freescale Semiconductor, Inc.
Chapter 23
Interrupt (IRQ)
23.1 Introduction
The external interrupt (IRQ) module provides a maskable interrupt input.
23.2 Features
Features of the IRQ module include:
•
• IRQ Interrupt Control bits
• Programmable edge-only or edge and level interrupt sensitivity
• Automatic interrupt acknowledge
• Internal pullup device
A low level applied to the external interrupt request (IRQ) pin can latch a CPU interrupt
request. The following figure shows the structure of the IRQ module:
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
325
Features
IRQACK
RESET
SYNCHRONIZER
BUSCLK
VDD
1
IRQ
0
IRQF
D
S
TO CPU
CLR
Q
SYNCHRONIZER
CK
IRQPE
STOP
IRQEDG
To pullup enable logic for IRQ
IRQPDD
TO INTERNAL
IRQMOD
STOP
BYPASS
IRQIE
IRQ
INTERRUPT
REQUEST
MODULES
WAKE-UP
INPUTS
Figure 23-1. IRQ module block diagram
External interrupts are managed by the IRQSC status and control register. When the IRQ
function is enabled, synchronous logic monitors the pin for edge-only or edge-and-level
events. When the MCU is in Stop mode and system clocks are shut down, a separate
asynchronous path is used so that the IRQ, if enabled, can wake the MCU.
23.2.1 Pin configuration options
The IRQ Pin Enable (IRQSC[IRQPE]) control field must be 1 for the IRQ pin to act as
the IRQ input. The user can choose the polarity of edges or levels detected (IRQEDG),
whether the pin detects edges-only or edges and levels (IRQMOD), or whether an event
causes an interrupt or only sets the IRQSC[IRQF] flag, which can be polled by software.
When enabled, the IRQ pin defaults to use an internal pullup device (IRQSC[IRQPDD] =
0). If the user uses an external pullup or pulldown, the IRQSC[IRQPDD] can be written
to a 1 to turn off the internal device.
BIH and BIL instructions may be used to detect the level on the IRQ pin when it is
configured to act as the IRQ input.
Note
This pin does not contain a clamp diode to VDD and must not be
driven above VDD. The voltage measured on the internally
pullup IRQ pin may be as low as VDD – 0.7 V. The internal
gates connected to this pin are pulled all the way to VDD.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
326
Freescale Semiconductor, Inc.
Chapter 23 Interrupt (IRQ)
When enabling the IRQ pin for use, IRQSC[IRQF] will be set,
and must be cleared prior to enabling the interrupt. When
configuring the pin for falling edge and level sensitivity in a 3
V system, it is necessary to wait at least cycles between
clearing the flag and enabling the interrupt.
23.2.2 Edge and level sensitivity
The IRQSC[IRQMOD] control field reconfigures the detection logic so that it can detect
edge events and pin levels. In this detection mode, IRQSC[IRQF] status flag is set when
an edge is detected, if the IRQ pin changes from the deasserted to the asserted level, but
the flag is continuously set and cannot be cleared as long as the IRQ pin remains at the
asserted level.
23.3 Interrupt pin request register
IRQ memory map
Absolute
address
(hex)
Register name
4003_1000
Interrupt Pin Request Status and Control Register (IRQ_SC)
Width
Access
(in bits)
8
R/W
Reset value
Section/
page
00h
23.3.1/327
23.3.1 Interrupt Pin Request Status and Control Register (IRQ_SC)
This direct page register includes status and control bits, which are used to configure the
IRQ function, report status, and acknowledge IRQ events.
Address: 4003_1000h base + 0h offset = 4003_1000h
Bit
7
Read
0
6
Write
Reset
0
5
4
IRQPDD
IRQEDG
IRQPE
0
0
0
3
2
IRQF
0
IRQACK
0
0
1
0
IRQIE
IRQMOD
0
0
IRQ_SC field descriptions
Field
Description
7
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
6
IRQPDD
Interrupt Request (IRQ) Pull Device Disable
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
327
Interrupt pin request register
IRQ_SC field descriptions (continued)
Field
Description
This read/write control bit is used to disable the internal pullup device when the IRQ pin is enabled (IRQPE
= 1) allowing for an external device to be used.
0
1
5
IRQEDG
Interrupt Request (IRQ) Edge Select
This read/write control field is used to select the polarity of edges or levels on the IRQ pin that cause IRQF
to be set. The IRQMOD control field determines whether the IRQ pin is sensitive to both edges and levels
or only edges. When the IRQ pin is enabled as the IRQ input and is configured to detect rising edges, the
optional pullup resistor is disabled.
0
1
4
IRQPE
This read/write control field enables the IRQ pin function. When this field is set, the IRQ pin can be used
as an interrupt request.
1
IRQIE
This read-only status field indicates when an interrupt request event has occurred.
No IRQ request
IRQ event is detected.
IRQ Acknowledge
This write-only field is used to acknowledge interrupt request events (write 1 to clear IRQF). Writing 0 has
no meaning or effect. Reads always return 0. If edge-and-level detection is selected (IRQMOD = 1), IRQF
cannot be cleared while the IRQ pin remains at its asserted level.
IRQ Interrupt Enable
This read/write control field determines whether IRQ events generate an interrupt request.
0
1
0
IRQMOD
IRQ pin function is disabled.
IRQ pin function is enabled.
IRQ Flag
0
1
2
IRQACK
IRQ is falling-edge or falling-edge/low-level sensitive.
IRQ is rising-edge or rising-edge/high-level sensitive.
IRQ Pin Enable
0
1
3
IRQF
IRQ pull device enabled if IRQPE = 1.
IRQ pull device disabled if IRQPE = 1.
Interrupt request when IRQF set is disabled (use polling).
Interrupt requested whenever IRQF = 1.
IRQ Detection Mode
This read/write control field selects either edge-only detection or edge-and-level detection.
0
1
IRQ event is detected only on falling/rising edges.
IRQ event is detected on falling/rising edges and low/high levels.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
328
Freescale Semiconductor, Inc.
Chapter 24
Analog-to-digital converter (ADC)
24.1 Introduction
The 12-bit analog-to-digital converter (ADC) is a successive approximation ADC
designed for operation within an integrated microcontroller system-on-chip.
24.1.1 Features
Features of the ADC module include:
• Linear Successive Approximation algorithm with 8-, 10-, or 12-bit resolution
• Up to 16 external analog inputs, external pin inputs, and 5 internal analog inputs
including internal bandgap, temperature sensor, and references
• Output formatted in 8-, 10-, or 12-bit right-justified unsigned format
• Single or Continuous Conversion (automatic return to idle after single conversion)
• Support up to eight result FIFO with selectable FIFO depth
• Configurable sample time and conversion speed/power
• Conversion complete flag and interrupt
• Input clock selectable from up to four sources
• Operation in Wait or Stop modes for lower noise operation
• Asynchronous clock source for lower noise operation
• Selectable asynchronous hardware conversion trigger
• Automatic compare with interrupt for less-than, or greater-than or equal-to,
programmable value
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
329
External Signal Description
24.1.2 Block Diagram
This figure provides a block diagram of the ADC module.
7
5-bit ch
0
12-bit AD result
6
5-bit ch
1
12-bit AD result
5
5-bit ch
2
12-bit AD result
4
5-bit ch
3
12-bit AD result
3
4
12-bit AD result
2
5-bit ch
5-bit ch
5
12-bit AD result
1
5-bit ch
6
12-bit AD result
0
5-bit ch
7
12-bit AD result
AD RESULT FIFO
AD CHANNEL FIFO
AFDEP
Off-chip Source Channels
Analog Result
FIFO Fulfilled
Input Channel
FIFO Fulfilled
AD0
AD1
AD2
AIEN
Interrupt to CPU
AD14
AD15
V SS
Reserved
AD19-AD16
AD21-AD20
AD22
Temperature Sensor
Internal Bandgap
ANALOG MUX
AD0 to AD15 from External
Pin Inputs or Reserved
COCO
SAR ADC
ADCK
AD23
CONTROL
SEQUENCER
COMPARE
LOGIC
AD29
Reserved
AD30
AD31
VREFL
VREFH
None (Module Disabled)
AD32
ADTRG MODE ADLSMP ADLPC ACFGT
On-chip Source Channels
ADCO
STOP
ACFE
ALT CLK
BUS CLK
2
ADACK
CLK MUX
ADHWT
CLOCK
DIVIDER
ADICLK
ADIV
Compare Value
ASYNC
CLOCK
GENERATOR
Figure 24-1. ADC Block Diagram
24.2 External Signal Description
The ADC module supports up to 24 separate analog inputs. It also requires four supply/
reference/ground connections.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
330
Freescale Semiconductor, Inc.
Chapter 24 Analog-to-digital converter (ADC)
Table 24-1. Signal Properties
Name
Function
AD23–AD0
Analog Channel inputs
VREFH
High reference voltage
VREFL
Low reference voltage
VDDA
Analog power supply
VSSA
Analog ground
24.2.1 Analog Power (VDDA)
The ADC analog portion uses VDDA as its power connection. In some packages, VDDA is
connected internally to VDD. If externally available, connect the VDDA pin to the same
voltage potential as VDD. External filtering may be necessary to ensure clean VDDA for
good results.
24.2.2 Analog Ground (VSSA)
The ADC analog portion uses VSSA as its ground connection. In some packages, VSSA is
connected internally to VSS. If externally available, connect the VSSA pin to the same
voltage potential as VSS.
24.2.3 Voltage Reference High (VREFH)
VREFH is the high reference voltage for the converter. In some packages, VREFH is
connected internally to VDDA. If externally available, VREFH may be connected to the
same potential as VDDA or may be driven by an external source between the minimum
VDDA specified in the data sheet and the VDDA potential (VREFH must never exceed
VDDA).
24.2.4 Voltage Reference Low (VREFL)
VREFL is the low-reference voltage for the converter. In some packages, VREFL is
connected internally to VSSA. If externally available, connect the VREFL pin to the same
voltage potential as VSSA.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
331
ADC Control Registers
24.2.5 Analog Channel Inputs (ADx)
The ADC module supports up to 24 separate analog inputs. An input is selected for
conversion through the ADCH channel select bits.
24.3 ADC Control Registers
ADC memory map
Absolute
address
(hex)
Register name
Width
Access
(in bits)
Reset value
Section/
page
4003_B000
Status and Control Register 1 (ADC_SC1)
32
R/W
0000_001Fh
24.3.1/332
4003_B004
Status and Control Register 2 (ADC_SC2)
32
R/W
0000_0008h
24.3.2/335
4003_B008
Status and Control Register 3 (ADC_SC3)
32
R/W
0000_0000h
24.3.3/337
4003_B00C Status and Control Register 4 (ADC_SC4)
32
R/W
0000_0000h
24.3.4/338
4003_B010
Conversion Result Register (ADC_R)
32
R
0000_0000h
24.3.5/339
4003_B014
Compare Value Register (ADC_CV)
32
R/W
0000_0000h
24.3.6/340
4003_B018
Pin Control 1 Register (ADC_APCTL1)
32
R/W
0000_0000h
24.3.7/341
32
R/W
0000_0000h
24.3.8/341
4003_B01C Status and Control Register 5 (ADC_SC5)
24.3.1 Status and Control Register 1 (ADC_SC1)
This section describes the function of the ADC status and control register (ADC_SC1).
Writing ADC_SC1 aborts the current conversion and initiates a new conversion (if the
ADCH bits are equal to a value other than all 1s).
When FIFO is enabled, the analog input channel FIFO is written via ADCH. The analog
input channel queue must be written to ADCH continuously. The resulting FIFO follows
the order in which the analog input channel is written. The ADC will start conversion
when the input channel FIFO is fulfilled at the depth indicated by the
ADC_SC4[AFDEP]. Any write 0x1F to these bits will reset the FIFO and stop the
conversion if it is active.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
332
Freescale Semiconductor, Inc.
Chapter 24 Analog-to-digital converter (ADC)
Address: 4003_B000h base + 0h offset = 4003_B000h
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
0
R
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
AIEN
0
0
1
1
COCO
Reset
ADCO
W
0
R
ADCH
W
Reset
0
0
0
0
0
0
0
0
0
1
1
1
ADC_SC1 field descriptions
Field
31–8
Reserved
7
COCO
Description
This field is reserved.
This read-only field is reserved and always has the value 0.
Conversion Complete Flag
Conversion Complete Flag. The COCO flag is a read-only bit set each time a conversion is completed
when the compare function is disabled (ADC_SC2[ACFE] = 0). When the compare function is enabled
(ADC_SC2[ACFE] = 1), the COCO flag is set upon completion of a conversion only if the compare result is
true. When the FIFO function is enabled (ADC_SC4[AFDEP] > 0), the COCO flag is set upon completion
of the set of FIFO conversion. This bit is cleared when ADC_SC1 is written or when ADC_R is read.
0
1
6
AIEN
Interrupt Enable
AIEN enables conversion complete interrupts. When COCO becomes set while AIEN is high, an interrupt
is asserted.
0
1
5
ADCO
Conversion not completed.
Conversion completed.
Conversion complete interrupt disabled.
Conversion complete interrupt enabled.
Continuous Conversion Enable
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
333
ADC Control Registers
ADC_SC1 field descriptions (continued)
Field
Description
ADCO enables continuous conversions.
0
1
ADCH
One conversion following a write to the ADC_SC1 when software triggered operation is selected, or
one conversion following assertion of ADHWT when hardware triggered operation is selected. When
the FIFO function is enabled (AFDEP > 0), a set of conversion are triggered when
ADC_SC2[ADTRG]=0 or both ADC_SC2[ADTRG]=1 and ADC_SC4[HTRGME]=1.
Continuous conversions are initiated following a write to ADC_SC1 when software triggered operation
is selected. Continuous conversions are initiated by an ADHWT event when hardware triggered
operation is selected. When the FIFO function is enabled (AFDEP > 0), a set of conversions are loop
triggered.
Input Channel Select
The ADCH bits form a 5-bit field that selects one of the input channels.
00000-01111
10000-10011
10100-10101
10110
10111
11000-11100
11101
11110
11111
AD0-AD15
VSS
Reserved
Temperature Sensor
Bandgap
Reserved
VREFH
VREFL
Module disabled
NOTE: Reset FIFO in FIFO mode.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
334
Freescale Semiconductor, Inc.
Chapter 24 Analog-to-digital converter (ADC)
24.3.2 Status and Control Register 2 (ADC_SC2)
The ADC_SC2 register controls the compare function, conversion trigger, and conversion
active of the ADC module.
Address: 4003_B000h base + 4h offset = 4003_B004h
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
0
R
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
ACFGT
FEMPTY
FFULL
ACFE
0
0
0
ADACT
Reset
ADTRG
W
0
R
REFSEL
W
Reset
0
0
0
0
0
0
0
0
0
1
0
0
0
ADC_SC2 field descriptions
Field
31–8
Reserved
7
ADACT
Description
This field is reserved.
This read-only field is reserved and always has the value 0.
Conversion Active
Indicates that a conversion is in progress. ADACT is set when a conversion is initiated and cleared when a
conversion is completed or aborted.
0
1
6
ADTRG
Conversion not in progress.
Conversion in progress.
Conversion Trigger Select
Selects the type of trigger used for initiating a conversion. Two types of trigger are selectable: software
trigger and hardware trigger. When software trigger is selected, a conversion is initiated following a write
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
335
ADC Control Registers
ADC_SC2 field descriptions (continued)
Field
Description
to ADC_SC1. When hardware trigger is selected, a conversion is initiated following the assertion of the
ADHWT input.
0
1
5
ACFE
Compare Function Enable
Enables the compare function.
0
1
4
ACFGT
2
FFULL
REFSEL
Compare function disabled.
Compare function enabled.
Compare Function Greater Than Enable
Configures the compare function to trigger when the result of the conversion of the input being monitored
is greater than or equal to the compare value. The compare function defaults to triggering when the result
of the compare of the input being monitored is less than the compare value.
0
1
3
FEMPTY
Software trigger selected.
Hardware trigger selected.
Compare triggers when input is less than compare level.
Compare triggers when input is greater than or equal to compare level.
Result FIFO empty
0
1
Indicates that ADC result FIFO have at least one valid new data.
Indicates that ADC result FIFO have no valid new data.
Result FIFO full
0
1
Indicates that ADC result FIFO is not full and next conversion data still can be stored into FIFO.
Indicates that ADC result FIFO is full and next conversion will override old data in case of no read
action.
Voltage Reference Selection
Selects the voltage reference source used for conversions.
00
01
10
11
Default voltage reference pin pair (VREFH/VREFL).
Analog supply pin pair (VDDA/VSSA).
Reserved.
Reserved - Selects default voltage reference (VREFH/VREFL) pin pair.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
336
Freescale Semiconductor, Inc.
Chapter 24 Analog-to-digital converter (ADC)
24.3.3 Status and Control Register 3 (ADC_SC3)
ADC_SC3 selects the mode of operation, clock source, clock divide, and configure for
low power or long sample time.
Address: 4003_B000h base + 8h offset = 4003_B008h
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
0
R
W
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
ADLPC
0
R
W
Reset
0
0
0
0
0
0
0
0
0
ADLSMP
Reset
ADIV
0
0
0
MODE
0
0
ADICLK
0
0
ADC_SC3 field descriptions
Field
31–8
Reserved
7
ADLPC
Description
This field is reserved.
This read-only field is reserved and always has the value 0.
Low-Power Configuration
ADLPC controls the speed and power configuration of the successive approximation converter. This
optimizes power consumption when higher sample rates are not required.
0
1
6–5
ADIV
Clock Divide Select
ADIV selects the divide ratio used by the ADC to generate the internal clock ADCK.
00
01
10
11
4
ADLSMP
High speed configuration.
Low power configuration:The power is reduced at the expense of maximum clock speed.
Divide ration = 1, and clock rate = Input clock.
Divide ration = 2, and clock rate = Input clock ÷ 2.
Divide ration = 3, and clock rate = Input clock ÷ 4.
Divide ration = 4, and clock rate = Input clock ÷ 8.
Long Sample Time Configuration
ADLSMP selects between long and short sample time. This adjusts the sample period to allow higher
impedance inputs to be accurately sampled or to maximize conversion speed for lower impedance inputs.
Longer sample times can also be used to lower overall power consumption when continuous conversions
are enabled if high conversion rates are not required.
0
1
Short sample time.
Long sample time.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
337
ADC Control Registers
ADC_SC3 field descriptions (continued)
Field
Description
3–2
MODE
Conversion Mode Selection
MODE bits are used to select between 12-, 10-, or 8-bit operation.
00
01
10
11
ADICLK
8-bit conversion (N = 8)
10-bit conversion (N = 10)
12-bit conversion (N = 12)
Reserved
Input Clock Select
ADICLK bits select the input clock source to generate the internal clock ADCK.
00
01
10
11
Bus clock
Bus clock divided by 2
Alternate clock (ALTCLK)
Asynchronous clock (ADACK)
24.3.4 Status and Control Register 4 (ADC_SC4)
This register controls the FIFO scan mode, FIFO compare function and FIFO depth
selection of the ADC module.
Address: 4003_B000h base + Ch offset = 4003_B00Ch
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
0
R
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
0
0
0
0
R
W
Reset
0
0
0
0
0
0
0
ACFSEL
0
ASCANE
Reset
HTRGME
W
0
0
0
AFDEP
0
0
0
0
0
ADC_SC4 field descriptions
Field
Description
31–9
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
8
HTRGME
Hardware Trigger Multiple Conversion Enable
This field enables hardware trigger multiple conversion.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
338
Freescale Semiconductor, Inc.
Chapter 24 Analog-to-digital converter (ADC)
ADC_SC4 field descriptions (continued)
Field
Description
0
1
One hardware trigger pulse triggers one conversion.
One hardware trigger pulse triggers multiple conversions in fifo mode.
7
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
6
ASCANE
FIFO Scan Mode Enable
The FIFO always use the first dummied FIFO channels when it is enabled. When this bit is set and FIFO
function is enabled, ADC will repeat using the first FIFO channel as the conversion channel until the result
FIFO is fulfilled. In continuous mode (ADCO = 1), ADC will start next conversion with the same channel
when COCO is set.
0
1
5
ACFSEL
Compare Function Selection
Compare function select OR/AND when the FIFO function is enabled (AFDEP > 0). When this field is
cleared, ADC will OR all of compare triggers and set COCO after at least one of compare trigger occurs.
When this field is set, ADC will AND all of compare triggers and set COCO after all of compare triggers
occur.
0
1
4–3
Reserved
AFDEP
FIFO scan mode disabled.
FIFO scan mode enabled.
OR all of compare trigger.
AND all of compare trigger.
This field is reserved.
This read-only field is reserved and always has the value 0.
FIFO Depth
FIFO Depth enables the FIFO function and sets the depth of FIFO. When AFDEP is cleared, the FIFO is
disabled. When AFDEP is set to nonzero, the FIFO function is enabled and the depth is indicated by the
AFDEP bits. The ADC_SC1[ADCH] and ADC_R must be accessed by FIFO mode when FIFO function is
enabled. ADC starts conversion when the analog channel FIFO is upon the level indicated by AFDEP bits.
The COCO bit is set when the set of conversions are completed and the result FIFO is upon the level
indicated by AFDEP bits.
000
001
010
011
100
101
110
111
FIFO is disabled.
2-level FIFO is enabled.
3-level FIFO is enabled..
4-level FIFO is enabled.
5-level FIFO is enabled.
6-level FIFO is enabled.
7-level FIFO is enabled.
8-level FIFO is enabled.
24.3.5 Conversion Result Register (ADC_R)
In 12-bit operation, ADC_R contains the 12 bits of the result of a 12-bit conversion.
In 10-bit mode, ADC_R contains the 10 bits of the result of a 10-bit conversion.
In 8-bit mode, ADC_R contains the 8 bits of the result of a 8-bit conversion.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
339
ADC Control Registers
ADC_R is updated each time a conversion completes except when automatic compare is
enabled and the compare condition is not met.
When FIFO is enabled, the result FIFO is read via ADC_R. The ADC conversion
completes when the input channel FIFO is fulfilled at the depth indicated by the AFDEP.
The AD result FIFO can be read via ADC_R continuously by the order set in analog
input channel ADCH.
If the MODE bits are changed, any data in ADC_R becomes invalid.
Address: 4003_B000h base + 10h offset = 4003_B010h
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
0
R
6
5
4
3
2
1
0
0
0
0
0
0
ADR
W
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
ADC_R field descriptions
Field
Description
31–12
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
ADR
Conversion Result
24.3.6 Compare Value Register (ADC_CV)
This register holds the compare value. Bits ADCV11:ADCV0 are compared to the 12 bits
of the result following a conversion in 12-bit mode.
Address: 4003_B000h base + 14h offset = 4003_B014h
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
0
R
0
0
0
0
0
0
0
0
0
0
5
4
3
2
1
0
0
0
0
0
0
CV
W
Reset
6
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
ADC_CV field descriptions
Field
31–12
Reserved
CV
Description
This field is reserved.
This read-only field is reserved and always has the value 0.
Conversion Result[11:0]
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
340
Freescale Semiconductor, Inc.
Chapter 24 Analog-to-digital converter (ADC)
24.3.7 Pin Control 1 Register (ADC_APCTL1)
The pin control registers disable the I/O port control of MCU pins used as analog inputs.
APCTL1 is used to control the pins associated with channels 0-31 of the ADC module.
Address: 4003_B000h base + 18h offset = 4003_B018h
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
0
R
0
0
0
0
0
0
0
0
7
6
5
4
3
2
1
0
0
0
0
0
0
0
0
ADPC
W
Reset
8
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
ADC_APCTL1 field descriptions
Field
Description
31–16
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
ADPC
ADC Pin Control
ADPCx controls the pin associated with channel ADx.
0
1
ADx pin I/O control enabled.
ADx pin I/O control disabled.
24.3.8 Status and Control Register 5 (ADC_SC5)
ADC_SC5 selects the hardware trigger mask.
Address: 4003_B000h base + 1Ch offset = 4003_B01Ch
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
0
R
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
HTRGMASKE
HTRGMASKS
EL
W
0
0
0
0
0
0
0
0
0
0
R
W
Reset
0
0
0
0
0
0
0
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
341
Functional description
ADC_SC5 field descriptions
Field
31–2
Reserved
1
HTRGMASKE
Description
This field is reserved.
This read-only field is reserved and always has the value 0.
Hardware Trigger Mask Enable
This field enables hardware trigger mask when HTRGMASKSEL is low.
0
1
Hardware trigger mask disable.
Hardware trigger mask enable and hardware trigger cannot trigger ADC conversion..
0
Hardware Trigger Mask Mode Select
HTRGMASKSEL
This field selects hardware trigger mask mode.
0
1
Hardware trigger mask with HTRGMASKE.
Hardware trigger mask automatically when data fifo is not empty.
24.4 Functional description
The ADC module is disabled during reset or when the ADC_SC1[ADCH] bits are all
high. The module is idle when a conversion has completed and another conversion has
not been initiated. When idle, the module is in its lowest power state.
The ADC can perform an analog-to-digital conversion on any of the software selectable
channels. In 12-bit mode, the selected channel voltage is converted by a successive
approximation algorithm into a 12-bit digital result. In 10-bit mode, the selected channel
voltage is converted by a successive approximation algorithm into a 10-bit digital result.
In 8-bit mode, the selected channel voltage is converted by a successive approximation
algorithm into a 8-bit digital result.
When the conversion is completed, the result is placed in the data registers (ADC_R). In
10-bit mode, the result is rounded to 10 bits and placed in the data registers (ADC_R). In
8-bit mode, the result is rounded to 8 bits and placed in ADC_R. The conversion
complete flag (ADC_SC1[COCO]) is then set and an interrupt is generated if the
conversion complete interrupt has been enabled (ADC_SC1[AIEN] = 1).
The ADC module has the capability of automatically comparing the result of a
conversion with the contents of its compare registers. The compare function is enabled by
setting the ADC_SC2[ACFE] bit and operates with any of the conversion modes and
configurations.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
342
Freescale Semiconductor, Inc.
Chapter 24 Analog-to-digital converter (ADC)
24.4.1 Clock select and divide control
One of four clock sources can be selected as the clock source for the ADC module. This
clock source is then divided by a configurable value to generate the input clock to the
converter (ADCK). The clock is selected from one of the following sources by means of
the ADC_SC3[ADICLK] bits.
• The bus clock divided by 2: For higher bus clock rates, this allows a maximum
divide by 16 of the bus clock.
• ALTCLK, that is, alternate clock which is OSC_OUT
• The asynchronous clock (ADACK): This clock is generated from a clock source
within the ADC module. When selected as the clock source, this clock remains active
while the MCU is in Wait or Stop mode and allows conversions in these modes for
lower noise operation.
Whichever clock is selected, its frequency must fall within the specified frequency range
for ADCK. If the available clocks are too slow, the ADC does not perform according to
specifications. If the available clocks are too fast, the clock must be divided to the
appropriate frequency. This divider is specified by the ADC_SC3[ADIV] bits and can be
divide-by 1, 2, 4, or 8.
24.4.2 Input select and pin control
The Pin Control register ( ADC_APCTL1) disables the I/O port control of the pins used
as analog inputs. When a pin control register bit is set, the following conditions are
forced for the associated MCU pin:
• The output buffer is forced to its high impedance state.
• The input buffer is disabled. A read of the I/O port returns a zero for any pin with its
input buffer disabled.
• The pullup is disabled.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
343
Functional description
24.4.3 Hardware trigger
The ADC module has a selectable asynchronous hardware conversion trigger, ADHWT,
that is enabled when the ADC_SC2[ADTRG] bit is set. This source is not available on all
MCUs. See the module introduction for information on the ADHWT source specific to
this MCU.
When ADHWT source is available and hardware trigger is enabled
( ADC_SC2[ADTRG] = 1), a conversion is initiated on the rising edge of ADHWT. If a
conversion is in progress when a rising edge occurs, the rising edge is ignored. In
continuous convert configuration, only the initial rising edge to launch continuous
conversions is observed. The hardware trigger function operates in conjunction with any
of the conversion modes and configurations.
24.4.4 Conversion control
Conversions can be performed in 12-bit mode, 10-bit mode, or 8-bit mode as determined
by the ADC_SC3[MODE] bits. Conversions can be initiated by a software or hardware
trigger. In addition, the ADC module can be configured for low power operation, long
sample time, continuous conversion, and an automatic compare of the conversion result
to a software determined compare value.
24.4.4.1 Initiating conversions
A conversion initiates under the following conditions:
• A write to ADC_SC1 or a set of write to ADC_SC1 in FIFO mode (with ADCH bits
not all 1s) if software triggered operation is selected.
• A hardware trigger (ADHWT) event if hardware triggered operation is selected.
• The transfer of the result to the data registers when continuous conversion is enabled.
If continuous conversions are enabled, a new conversion is automatically initiated after
the completion of the current conversion. In software triggered operation, continuous
conversions begin after ADC_SC1 is written and continue until aborted. In hardware
triggered operation, continuous conversions begin after a hardware trigger event and
continue until aborted.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
344
Freescale Semiconductor, Inc.
Chapter 24 Analog-to-digital converter (ADC)
24.4.4.2 Completing conversions
A conversion is completed when the result of the conversion is transferred into the data
result register, ADC_R. This is indicated by the setting of ADC_SC1[COCO]. An
interrupt is generated if ADC_SC1[AIEN] is high at the time that ADC_SC1[COCO] is
set.
24.4.4.3 Aborting conversions
Any conversion in progress is aborted in the following cases:
• A write to ADC_SC1 occurs.
• The current conversion will be aborted and a new conversion will be initiated, if
ADC_SC1[ADCH] are not all 1s and ADC_SC4[AFDEP] are all 0s.
• The current conversion and the rest of conversions will be aborted and no new
conversion will be initialed, if ADC_SC4[AFDEP] are not all 0s.
• A new conversion will be initiated when the FIFO is re-fulfilled upon the levels
indicated by the ADC_SC4[AFDEP] bits).
• A write to ADC_SC2, ADC_SC3, ADC_SC4, ADC_CV occurs. This indicates a
mode of operation change has occurred and the current and rest of conversions (when
ADC_SC4[AFDEP] are not all 0s) are therefore invalid.
• The MCU is reset.
• The MCU enters Stop mode with ADACK not enabled.
When a conversion is aborted, the contents of the data register, ADC_R, are not altered.
However, they continue to be the values transferred after the completion of the last
successful conversion. If the conversion was aborted by a reset, ADC_R returns to their
reset states.
24.4.4.4 Power control
The ADC module remains in its idle state until a conversion is initiated. If ADACK is
selected as the conversion clock source, the ADACK clock generator is also enabled.
Power consumption when active can be reduced by setting ADC_SC3[ADLPC]. This
results in a lower maximum value for fADCK (see the data sheet).
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
345
Functional description
24.4.4.5 Sample time and total conversion time
The total conversion time depends on the sample time (as determined by
ADC_SC3[ADLSMP]), the MCU bus frequency, the conversion mode (8-bit, 10-bit or
12-bit), and the frequency of the conversion clock (fADCK). After the module becomes
active, sampling of the input begins.ADC_SC3[ADLSMP] selects between short (3.5
ADCK cycles) and long (23.5 ADCK cycles) sample times. When sampling is complete,
the converter is isolated from the input channel and a successive approximation algorithm
is performed to determine the digital value of the analog signal. The result of the
conversion is transferred to ADC_R upon completion of the conversion algorithm.
If the bus frequency is less than the fADCK frequency, precise sample time for continuous
conversions cannot be guaranteed when short sample is enabled (ADC_SC3[ADLSMP]
= 0). If the bus frequency is less than 1/11th of the fADCK frequency, precise sample time
for continuous conversions cannot be guaranteed when long sample is enabled
(ADC_SC3[ADLSMP] = 1).
The maximum total conversion time for different conditions is summarized in the table
below.
Table 24-11. Total conversion time vs. control conditions
Conversion type
ADICLK
ADLSMP
Max total conversion time
Single or first continuous 8-bit
0x, 10
0
20 ADCK cycles + 5 bus clock cycles
Single or first continuous 10-bit or 12-bit
0x, 10
0
23 ADCK cycles + 5 bus clock cycles
Single or first continuous 8-bit
0x, 10
1
40 ADCK cycles + 5 bus clock cycles
Single or first continuous 10-bit or 12-bit
0x, 10
1
43 ADCK cycles + 5 bus clock cycles
Single or first continuous 8-bit
11
0
5 µs + 20 ADCK + 5 bus clock cycles
Single or first continuous 10-bit or 12-bit
11
0
5 µs + 23 ADCK + 5 bus clock cycles
Single or first continuous 8-bit
11
1
5 µs + 40 ADCK + 5 bus clock cycles
Single or first continuous 10-bit or 12-bit
11
1
5 µs + 43 ADCK + 5 bus clock cycles
Subsequent continuous 8-bit;
xx
0
17 ADCK cycles
xx
0
20 ADCK cycles
xx
1
37 ADCK cycles
xx
1
40 ADCK cycles
fBUS > fADCK
Subsequent continuous 10-bit or 12-bit;
fBUS > fADCK
Subsequent continuous 8-bit;
fBUS > fADCK/11
Subsequent continuous 10-bit or 12-bit;
fBUS > fADCK/11
The maximum total conversion time is determined by the selected clock source and the
divide ratio. The clock source is selectable by the ADC_SC3[ADICLK] bits, and the
divide ratio is specified by the ADC_SC3[ADIV] bits. For example, in 10-bit mode, with
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
346
Freescale Semiconductor, Inc.
Chapter 24 Analog-to-digital converter (ADC)
the bus clock selected as the input clock source, the input clock divide-by-1 ratio
selected, and a bus frequency of 8 MHz, then the conversion time for a single conversion
as given below:
The number of bus cycles at 8 MHz is:
Note
The ADCK frequency must be between fADCK minimum and
fADCK maximum to meet ADC specifications.
24.4.5 Automatic compare function
The compare function can be configured to check for an upper or lower limit. After the
input is sampled and converted, the result is added to the complement of the compare
value (ADC_CV). When comparing to an upper limit (ADC_SC2[ACFGT] = 1), if the
result is greater-than or equal-to the compare value, ADC_SC1[COCO] is set. When
comparing to a lower limit (ADC_SC2[ACFGT] = 0), if the result is less than the
compare value, ADC_SC1[COCO] is set. The value generated by the addition of the
conversion result and the complement of the compare value is transferred to ADC_R.
On completion of a conversion while the compare function is enabled, if the compare
condition is not true, ADC_SC1[COCO] is not set and no data is transferred to the result
registers. An ADC interrupt is generated on the setting of ADC_SC1[COCO] if the ADC
interrupt is enabled (ADC_SC1[AIEN] = 1).
On completion of all conversions while the compare function is enabled and FIFO
enabled, if none of the compare conditions are not true when ADC_SC4[ACFSEL] is low
or if not all of compare conditions are true when ADC_SC4[ACFSEL] is high,
ADC_SC1[COCO] is not set. The compare data are transferred to the result registers
regardless of compare condition true or false when FIFO enabled.
Note
The compare function can monitor the voltage on a channel
while the MCU is in Wait or Stop mode. The ADC interrupt
wakes the MCU when the compare condition is met.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
347
Functional description
Note
The compare function can not work in continuous conversion
mode when FIFO enabled.
24.4.6 FIFO operation
The ADC module supports FIFO operation to minimize the interrupts to CPU in order to
reduce CPU loading in ADC interrupt service routines. This module contains two FIFOs
to buffer analog input channels and analog results respectively.
The FIFO function is enabled when the ADC_SC4[AFDEP] bits are set non-zero. The
FIFO depth is indicated by these bits. The FIFO supports up to eight level buffer.
The analog input channel FIFO is accessed by ADC_SC1[ADCH] bits, when FIFO
function is enabled. The analog channel must be written to this FIFO in order. The ADC
will not start the conversion if the channel FIFO is fulfilled below the level indicated by
the ADC_SC4[AFDEP] bits, no matter whether software or hardware trigger is set. Read
ADC_SC1[ADCH] will read the current active channel value. Write to
ADC_SC1[ADCH] will re-fill channel FIFO to initial new conversion. It will abort
current conversion and any other conversions that did not start. Write to the ADC_SC1
after all the conversions are completed or ADC is in idle state.
The result of the FIFO is accessed by ADC_R register, when FIFO function is enabled.
The result must be read via these two registers by the same order of analog input channel
FIFO to get the proper results. Don't read ADC_R until all of the conversions are
completed in FIFO mode. The ADC_SC1[COCO] bit will be set only when all
conversions indicated by the analog input channel FIFO complete whatever software or
hardware trigger is set. An interrupt request will be submitted to CPU if the
ADC_SC1[AIEN] is set when the FIFO conversion completes and the
ADC_SC1[COCO] bit is set.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
348
Freescale Semiconductor, Inc.
Chapter 24 Analog-to-digital converter (ADC)
AFDEP
ADC_R read
ADC_R
AD CHANNEL FIFO
ADCH
5-bit ch
7
5-bit ch
6
5-bit ch
5
5-bit ch
4
5-bit ch
5-bit ch
3
2
5-bit ch
1
5-bit ch
0
FIFO Read/Write Logic reset
12-bit AD result
1
12-bit AD result
2
12-bit AD result
3
12-bit AD result
4
12-bit AD result
5
12-bit AD result
6
12-bit AD result
7
12-bit AD result
8
12-bit AD result
9
10
12-bit AD result
12-bit AD result
11
12-bit AD result
AD RESULT FIFO
ADCH write
0
COMPARE
LOGIC
Result FIFO Fulfilled
COMPARE
LOGIC
Channel FIFO Fulfilled
Result FIFO read pointer
FIFO Read/Write Logic
D Q
CK
COCO
Channel FIFO write pointer
Result FIFO write pointer
FIFO Work Logic
Channel FIFO read pointer
D Q
CK
FIFO conversion start
BUS CLK
Figure 24-10. FADC FIFO structure
If software trigger is enabled, the next analog channel is fetched from analog input
channel FIFO as soon as a conversion completes and its result is stored in the result
FIFO. When all conversions set in the analog input channel FIFO completes, the
ADC_SC1[COCO] bit is set and an interrupt request will be submitted to CPU if the
ADC_SC1[AIEN] bit is set.
If single hardware trigger mode is enabled(ADC_SC2[ADTRG]= 1 and
ADC_SC4[HTRGME]=0 ), the next analog is fetched from analog input channel FIFO
only when this conversion completes, its result is stored in the result FIFO, and the next
hardware trigger is fed to ADC module. If multi hardware tigger mode is
enabled(ADC_SC2[ADTRG]=1 and ADC_SC4[HTRGME]=1), the next analog is
fetched from analog input channel FIFO only when this conversion completes, its result
is stored in the result FIFO, and next conversion will start without waiting for next
hardware trigger. When all conversions set in the analog input channel FIFO completes,
the ADC_SC1[COCO] bit is set and an interrupt request will be submitted to CPU if the
ADC_SC1[AIEN] bit is set.
In single conversion in which ADC_SC1[ADCO] bit is clear, the ADC stops conversions
when ADC_SC1[COCO] bit is set until the channel FIFO is fulfilled again or new
hardware trigger occur.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
349
Functional description
The FIFO also provides scan mode to simplify the dummy work of input channel FIFO.
When the ADC_SC4[ASCANE] bit is set in FIFO mode, the FIFO will always use the
first dummied channel in spite of the value in the input channel FIFO. The ADC
conversion start to work in FIFO mode as soon as the first channel is dummied. The
following write operation to the input channel FIFO will cover the first channel element
in this FIFO. In scan FIFO mode, the ADC_SC1[COCO] bit is set when the result FIFO
is fulfilled according to the depth indicated by the ADC_SC4[AFDEP] bits.
In continuous conversion in which the ADC_SC1[ADCO] bit is set, the ADC starts next
conversion immediately when all conversions are completed. ADC module will fetch the
analog input channel from the beginning of analog input channel FIFO.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
350
Freescale Semiconductor, Inc.
Chapter 24 Analog-to-digital converter (ADC)
th
The n AD
channel fetch
max = AFDEP
Channel FIFO fulfilled
Start FIFOed Conversion
n
0
max
COCO = 1
Conversions Completed
The nth AD
result store
The nth AD
channel fetch
Software Triggered Single Conversion
max = AFDEP
Channel FIFO fulfilled
Start FIFOed Conversion
n
0
max
0
n
max
ADC_SC1[COCO] = 1
Conversions Completed
The nth AD
result store
The nth AD
channel fetch
when n hardware trigger occurs
0
n
max
Software Triggered Continuous Conversion
max = AFDEP
when last hardware trigger occurs
Channel FIFO fulfilled
Start FIFOed Conversion
when 1st hardware trigger occurs
n
0
max
The nth AD
result store
If new trigger occurs, the new set conversions will be generated
Hardware Triggered Single Conversion
ADC_SC1[COCO] = 1
Conversions Completed
ADC_SC4[HTRGME]=0
nth
The
AD
channel fetch
max = AFDEP
Channel FIFO fulfilled
Start FIFOed Conversion
when 1st hardware trigger occurs
0
n
The nth AD
result store
The nth AD
channel fetch
max
If new trigger occurs, the new set conversions will be generated
Hardware Triggered Multiple Conversion
ADC_SC4[HTRGME]=1
ADC_SC1[COCO] = 1
Conversions Completed
max = AFDEP
Channel FIFO fulfilled
Start FIFOed Conversion
when hardware trigger occurs
0
n
The nth AD
result store
max
0
n
Hardware Triggered Continuous Conversion
need one hardware trigger)
COCO = 1
(Only
Conversions Completed
Figure 24-11. ADC FIFO conversion sequence
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
351
Functional description
24.4.7 MCU wait mode operation
Wait mode is a low-power consumption standby mode from which recovery is fast
because the clock sources remain active. If a conversion is in progress when the MCU
enters wait mode, it continues until completion. Conversions can be initiated while the
MCU is in wait mode by means of the hardware trigger or if continuous conversions are
enabled.
The bus clock, bus clock divided by two, ALTCLK and ADACK are available as
conversion clock sources while in wait mode.
ADC_SC1[COCO] is set by a conversion complete event that generates an ADC interrupt
to wake the MCU from wait mode if the ADC interrupt is enabled (ADC_SC1[AIEN] =
1).
24.4.8 MCU Stop mode operation
Stop mode is a low-power consumption standby mode during which most or all clock
sources on the MCU are disabled.
24.4.8.1 Stop mode with ADACK disabled
If the asynchronous clock, ADACK, is not selected as the conversion clock, executing a
STOP instruction aborts the current conversion and places the ADC in its idle state. The
contents of ADC_R are unaffected by Stop mode. After exiting from Stop mode, a
software or hardware trigger is required to resume conversions.
24.4.8.2 Stop mode with ADACK enabled
If ADACK is selected as the conversion clock, the ADC continues operation during Stop
mode. For guaranteed ADC operation, the MCU's voltage regulator must remain active
during Stop mode. See the module introduction for configuration information for this
MCU.
If a conversion is in progress when the MCU enters Stop mode, it continues until
completion. Conversions can be initiated while the MCU is in Stop mode by means of the
hardware trigger or if continuous conversions are enabled.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
352
Freescale Semiconductor, Inc.
Chapter 24 Analog-to-digital converter (ADC)
A conversion complete event sets the ADC_SC1[COCO] and generates an ADC interrupt
to wake the MCU from Stop mode if the ADC interrupt is enabled (ADC_SC1[AIEN] =
1). In fifo mode, ADC cannot complete the conversion operation fully or wake the MCU
from Stop mode.
Note
The ADC module can wake the system from low-power stop
and cause the MCU to begin consuming run-level currents
without generating a system level interrupt. To prevent this
scenario, the data transfer blocking mechanism must be cleared
when entering Stop and continuing ADC conversions.
24.5 Initialization information
This section gives an example that provides some basic direction on how to initialize and
configure the ADC module. You can configure the module for 8-, 10-, or 12-bit
resolution, single or continuous conversion, and a polled or interrupt approach, among
many other options. Refer to ADC_SC3 register for information used in this example.
Note
Hexadecimal values prefixed by a 0x, binary values prefixed by
a %, and decimal values have no preceding character.
24.5.1 ADC module initialization example
Before the ADC module can be used to complete conversions, it must be initialized.
Given below is a method to initialize ADC module.
24.5.1.1 Initialization sequence
A typical initialization sequence is as follows:
1. Update the configuration register (ADC_SC3) to select the input clock source and the
divide ratio used to generate the internal clock, ADCK. This register is also used for
selecting sample time and low-power configuration.
2. Update status and control register 2 (ADC_SC2) to select the hardware or software
conversion trigger and compare function options, if enabled.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
353
Initialization information
3. Update status and control register 1 (ADC_SC1) to select whether conversions will
be continuous or completed only once, and to enable or disable conversion complete
interrupts. The input channel on which conversions will be performed is also selected
here.
24.5.1.2 Pseudo-code example
In this example, the ADC module is set up with interrupts enabled to perform a single 10bit conversion at low power with a long sample time on input channel 1, where the
internal ADCK clock is derived from the bus clock divided by 1.
Example: 24.5.1.2.1 General ADC initialization routine
void ADC_init(void)
{
/* The following code segment demonstrates how to initialize ADC by low-power mode,
long
sample time, bus frequency, software triggered from AD1 external pin without FIFO
enabled
*/
ADC_APCTL1 = ADC_APCTL1_ADPC1_MASK;
ADC_SC3 = ADC_SC3_ADLPC_MASK | ADC_SC3_ADLSMP_MASK | ADC_SC3_MODE0_MASK;
ADC_SC2 = 0x00;
ADC_SC1 = ADC_SC1_AIEN_MASK | ADC_SC1_ADCH0_MASK;
}
24.5.2 ADC FIFO module initialization example
Before the ADC module can be used to start FIFOed conversions, an initialization
procedure must be performed. A typical sequence is as follows:
1. Update the configuration register (ADC_SC3) to select the input clock source and the
divide ratio used to generate the internal clock, ADCK. This register is also used to
select sample time and low-power configuration.
2. Update the configuration register (ADC_SC4) to select the FIFO scan mode, FIFO
compare function selection (OR or AND function) and FIFO depth.
3. Update status and control register 2 (ADC_SC2) to select the hardware or software
conversion trigger, compare function options if enabled.
4. Update status and control register 1 (ADC_SC1) to select whether conversions will
be continuous or completed only once, and to enable or disable conversion complete
interrupts. The input channel on which conversions will be performed is also selected
here.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
354
Freescale Semiconductor, Inc.
Chapter 24 Analog-to-digital converter (ADC)
24.5.2.1 Pseudo-code example
In this example, the ADC module is set up with interrupts enabled to perform a single
hardware triggered 10-bit 4-level-FIFO conversion at low power with a long sample time
on input channels of 1, 3, 5, and 7. Here the internal ADCK clock is derived from the bus
clock divided by 1.
Example: 24.5.2.1.1 FIFO ADC initialization routine
void ADC_init(void)
{
/* The following code segment demonstrates how to initialize ADC by low-power mode, long
sample time, bus frequency, hardware triggered from AD1, AD3, AD5, and AD7 external pins
with 4-level FIFO enabled */
ADC_APCTL1 = ADC_APCTL1_ADPC6_MASK | ADC_APCTL1_ADPC5_MASK | ADC_APCTL1_ADPC3_MASK |
ADC_APCTL1_ADPC1_MASK;
ADC_SC3 = ADC_SC3_ADLPC_MASK | ADC_SC3_ADLSMP_MASK | ADC_SC3_MODE1_MASK;
// setting hardware trigger
ADC_SC2 = ADC_SC2_ADTRG_MASK ;
//4-Level FIFO
ADC_SC4 = ADC_SC4_AFDEP1_MASK | ADC_SC4_AFDEP0_MASK;
// dummy the 1st channel
ADC_SC1 = ADC_SC1_ADCH0_MASK;
// dummy the 2nd channel
ADC_SC1 = ADC_SC1_ADCH1_MASK | ADC_SC1_ADCH0_MASK;
// dummy the 3rd channel
ADC_SC1 = ADC_SC1_ADCH2_MASK | ADC_SC1_ADCH0_MASK;
// dummy the 4th channel and ADC starts conversion
ADC_SC1 = ADC_SC1_AIEN_MASK | ADC_SC1_ADCH2_MASK | ADC_SC1_ADCH1_MASK | ADC_SC1_ADCH0_MASK;
}
Example: 24.5.2.1.2 FIFO ADC interrupt service routine
unsigned short buffer[4];
interrupt VectorNumber_Vadc void ADC_isr(void)
{
/* The following code segment demonstrates read AD result FIFO */
// read conversion result of channel 1 and COCO bit is cleared
buffer[0] = ADC_R;
// read conversion result of channel 3
buffer[1] = ADC_R;
// read conversion result of channel 5
buffer[2] = ADC_R;
// read conversion result of channel 7
buffer[3] = ADC_R;
}
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
355
Application information
NOTE
ADC_R is 16-bit ADC result register, combined from
ADC_RH and ADC_RL
24.6 Application information
This section contains information for using the ADC module in applications. The ADC
has been designed to be integrated into a microcontroller for use in embedded control
applications requiring an A/D converter.
24.6.1 External pins and routing
The following sections discuss the external pins associated with the ADC module and
how they are used for best results.
24.6.1.1 Analog supply pins
The ADC module has analog power and ground supplies (VDDA and VSSA) available as
separate pins on some devices. VSSA is shared on the same pin as the MCU digital VSS on
some devices. On other devices, VSSA and VDDA are shared with the MCU digital supply
pins. In these cases, there are separate pads for the analog supplies bonded to the same
pin as the corresponding digital supply so that some degree of isolation between the
supplies is maintained.
When available on a separate pin, both VDDA and VSSA must be connected to the same
voltage potential as their corresponding MCU digital supply (VDD and VSS) and must be
routed carefully for maximum noise immunity and bypass capacitors placed as near as
possible to the package.
If separate power supplies are used for analog and digital power, the ground connection
between these supplies must be at the VSSA pin. This should be the only ground
connection between these supplies if possible. The VSSA pin makes a good single point
ground location.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
356
Freescale Semiconductor, Inc.
Chapter 24 Analog-to-digital converter (ADC)
24.6.1.2 Analog reference pins
In addition to the analog supplies, the ADC module has connections for two reference
voltage inputs. The high reference is VREFH, which may be shared on the same pin as
VDDA on some devices. The low reference is VREFL, which may be shared on the same
pin as VSSA on some devices.
When available on a separate pin, VREFH may be connected to the same potential as
VDDA, or may be driven by an external source between the minimum VDDA spec and the
VDDA potential (VREFH must never exceed VDDA). When available on a separate pin,
VREFL must be connected to the same voltage potential as VSSA. VREFH and VREFL must
be routed carefully for maximum noise immunity and bypass capacitors placed as near as
possible to the package.
AC current in the form of current spikes required to supply charge to the capacitor array
at each successive approximation step is drawn through the VREFH and VREFL loop. The
best external component to meet this current demand is a 0.1 µF capacitor with good high
frequency characteristics. This capacitor is connected between VREFH and VREFL and
must be placed as near as possible to the package pins. Resistance in the path is not
recommended because the current causes a voltage drop that could result in conversion
errors. Inductance in this path must be minimum (parasitic only).
24.6.1.3 Analog input pins
The external analog inputs are typically shared with digital I/O pins on MCU devices.
The pin I/O control is disabled by setting the appropriate control bit in one of the pin
control registers. Conversions can be performed on inputs without the associated pin
control register bit set. It is recommended that the pin control register bit always be set
when using a pin as an analog input. This avoids problems with contention because the
output buffer is in its high impedance state and the pullup is disabled. Also, the input
buffer draws DC current when its input is not at VDD or VSS. Setting the pin control
register bits for all pins used as analog inputs should be done to achieve lowest operating
current.
Empirical data shows that capacitors on the analog inputs improve performance in the
presence of noise or when the source impedance is high. Use of 0.01 µF capacitors with
good high-frequency characteristics is sufficient. These capacitors are not necessary in all
cases, but when used they must be placed as near as possible to the package pins and be
referenced to VSSA.
For proper conversion, the input voltage must fall between VREFH and VREFL. If the input
is equal to or exceeds VREFH, the converter circuit converts the signal to 0xFFF (full scale
12-bit representation), 0x3FF (full scale 10-bit representation) or 0xFF (full scale 8-bit
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
357
Application information
representation). If the input is equal to or less than VREFL, the converter circuit converts it
to 0x000. Input voltages between VREFH and VREFL are straight-line linear conversions.
There is a brief current associated with VREFL when the sampling capacitor is charging.
The input is sampled for 3.5 cycles of the ADCK source when ADC_SC3[ADLSMP] is
low, or 23.5 cycles when ADC_SC3[ADLSMP] is high.
For minimal loss of accuracy due to current injection, pins adjacent to the analog input
pins should not be transitioning during conversions.
24.6.2 Sources of error
Several sources of error exist for A/D conversions. These are discussed in the following
sections.
24.6.2.1 Sampling error
For proper conversions, the input must be sampled long enough to achieve the proper
accuracy. Given the maximum input resistance of approximately 7 kΩ and input
capacitance of approximately 5.5 pF, sampling to within 1/4 LSB (at 12-bit resolution)
can be achieved within the minimum sample window (3.5 cycles at 8 MHz maximum
ADCK frequency) provided the resistance of the external analog source (RAS) is kept
below 2 kΩ.
Higher source resistances or higher-accuracy sampling is possible by setting
ADC_SC3[ADLSMP] (to increase the sample window to 23.5 cycles) or decreasing
ADCK frequency to increase sample time.
24.6.2.2 Pin leakage error
Leakage on the I/O pins can cause conversion error if the external analog source
resistance (RAS) is high. If this error cannot be tolerated by the application, keep RAS
lower than VDDA / (2N*ILEAK) for less than 1/4 LSB leakage error (N = 8 in 8-bit, 10 in
10-bit or 12 in 12-bit mode).
24.6.2.3 Noise-induced errors
System noise that occurs during the sample or conversion process can affect the accuracy
of the conversion. The ADC accuracy numbers are guaranteed as specified only if the
following conditions are met:
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
358
Freescale Semiconductor, Inc.
Chapter 24 Analog-to-digital converter (ADC)
• There is a 0.1 µF low-ESR capacitor from VREFH to VREFL.
• There is a 0.1 µF low-ESR capacitor from VDDA to VSSA.
• If inductive isolation is used from the primary supply, an additional 1 µF capacitor is
placed from VDDA to VSSA.
• VSSA (and VREFL, if connected) is connected to VSS at a quiet point in the ground
plane.
• Operate the MCU in wait or Stop mode before initiating (hardware triggered
conversions) or immediately after initiating (hardware or software triggered
conversions) the ADC conversion.
• For software triggered conversions, immediately follow the write to ADC_SC1
with a stop instruction.
• For Stop mode operation, select ADACK as the clock source. Operation in Stop
reduces VDD noise but increases effective conversion time due to stop recovery.
• There is no I/O switching, input or output, on the MCU during the conversion.
There are some situations where external system activity causes radiated or conducted
noise emissions or excessive VDD noise is coupled into the ADC. In these situations, or
when the MCU cannot be placed in wait or Stop or I/O activity cannot be halted, these
recommended actions may reduce the effect of noise on the accuracy:
• Place a 0.01 µF capacitor (CAS) on the selected input channel to VREFL or VSSA (this
improves noise issues, but affects the sample rate based on the external analog source
resistance).
• Average the result by converting the analog input many times in succession and
dividing the sum of the results. Four samples are required to eliminate the effect of a
1LSB, one-time error.
• Reduce the effect of synchronous noise by operating off the asynchronous clock
(ADACK) and averaging. Noise that is synchronous to ADCK cannot be averaged
out.
24.6.2.4 Code width and quantization error
The ADC quantizes the ideal straight-line transfer function into 4096 steps (in 12-bit
mode). Each step ideally has the same height (1 code) and width. The width is defined as
the delta between the transition points to one code and the next. The ideal code width for
an N bit converter (in this case N can be 8, 10 or 12), defined as 1LSB, is:
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
359
Application information
There is an inherent quantization error due to the digitization of the result. For 8-bit or
10-bit conversions the code transitions when the voltage is at the midpoint between the
points where the straight line transfer function is exactly represented by the actual
transfer function. Therefore, the quantization error will be ± 1/2 lsb in 8- or 10-bit mode.
As a consequence, however, the code width of the first (0x000) conversion is only 1/2 lsb
and the code width of the last (0xFF or 0x3FF) is 1.5 lsb.
For 12-bit conversions the code transitions only after the full code width is present, so the
quantization error is -1 lsb to 0 lsb and the code width of each step is 1 lsb.
24.6.2.5 Linearity errors
The ADC may also exhibit non-linearity of several forms. Every effort has been made to
reduce these errors but the system must be aware of them because they affect overall
accuracy. These errors are:
• Zero-scale error (EZS) (sometimes called offset) — This error is defined as the
difference between the actual code width of the first conversion and the ideal code
width (1/2 lsb in 8-bit or 10-bit modes and 1 lsb in 12-bit mode). If the first
conversion is 0x001, the difference between the actual 0x001 code width and its ideal
(1 lsb) is used.
• Full-scale error (EFS) — This error is defined as the difference between the actual
code width of the last conversion and the ideal code width (1.5 lsb in 8-bit or 10-bit
modes and 1LSB in 12-bit mode). If the last conversion is 0x3FE, the difference
between the actual 0x3FE code width and its ideal (1 lsb) is used.
• Differential non-linearity (DNL) — This error is defined as the worst-case difference
between the actual code width and the ideal code width for all conversions.
• Integral non-linearity (INL) — This error is defined as the highest-value that the
absolute value of the running sum of DNL achieves. More simply, this is the worstcase difference of the actual transition voltage to a given code and its corresponding
ideal transition voltage, for all codes.
• Total unadjusted error (TUE) — This error is defined as the difference between the
actual transfer function and the ideal straight-line transfer function and includes all
forms of error.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
360
Freescale Semiconductor, Inc.
Chapter 24 Analog-to-digital converter (ADC)
24.6.2.6 Code jitter, non-monotonicity, and missing codes
Analog-to-digital converters are susceptible to three special forms of error. These are
code jitter, non-monotonicity, and missing codes.
Code jitter occurs when, at certain points, a given input voltage converts to one of two
values when sampled repeatedly. Ideally, when the input voltage is infinitesimally
smaller than the transition voltage, the converter yields the lower code (and vice-versa).
However, even small amounts of system noise can cause the converter to be
indeterminate, between two codes, for a range of input voltages around the transition
voltage. This range is normally around ±1/2 lsb in 8-bit or 10-bit mode, or around 2 lsb in
12-bit mode, and increases with noise.
This error may be reduced by repeatedly sampling the input and averaging the result.
Additionally the techniques discussed in Noise-induced errors reduces this error.
Non-monotonicity is defined when, except for code jitter, the converter converts to a
lower code for a higher input voltage. Missing codes are those values that are never
converted for any input value.
In 8-bit or 10-bit mode, the ADC is guaranteed to be monotonic and have no missing
codes.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
361
Application information
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
362
Freescale Semiconductor, Inc.
Chapter 25
Analog comparator (ACMP)
25.1 Introduction
The analog comparator module (ACMP) provides a circuit for comparing two analog
input voltages. The comparator circuit is designed to operate across the full range of the
supply voltage (rail-to-rail operation).
The analog mux provides a circuit for selecting an analog input signal from four
channels. One signal provided by the 6-bit DAC. The mux circuit is designed to operate
across the full range of the supply voltage. The 6-bit DAC is 64-tap resistor ladder
network which provides a selectable voltage reference for applications where voltage
reference is needed. The 64-tap resistor ladder network divides the supply reference Vin
into 64 voltage level. A 6-bit digital signal input selects output voltage level, which varies
from Vin to Vin/64. Vin can be selected from two voltage sources.
25.1.1 Features
ACMP features include:
• Operational over the whole supply range of 2.7 V to 5.5 V
• On-chip 6-bit resolution DAC with selectable reference voltage from VDD or internal
bandgap
• Configurable hysteresis
• Selectable interrupt on rising edge, falling edge, or both rising or falling edges of
comparator output
• Selectable inversion on comparator output
• Up to four selectable comparator inputs
• Operational in Stop mode
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
363
Introduction
25.1.2 Modes of operation
This section defines the ACMP operation in Wait, Stop, and Background Debug modes.
25.1.2.1 Operation in Wait mode
The ACMP continues to operate in Wait mode, if enabled. The interrupt can wake the
MCU if enabled.
25.1.2.2 Operation in Stop mode
The ACMP (including DAC and CMP) continues to operate in Stop mode if enabled. If
ACMP_CS[ACIE] is set, a ACMP interrupt can be generated to wake the MCU up from
Stop mode.
If the Stop is exited by an interrupt, the ACMP setting remains before entering the Stop
mode. If Stop is exited with a reset, the ACMP goes into its reset.
The user must turn off the DAC if the output is not used as a reference input of ACMP to
save power, because the DAC consumes additional power.
25.1.2.3 Operation in Debug mode
When the MCU is in Debug mode, the ACMP continues operating normally.
25.1.3 Block diagram
The block diagram of the ACMP module is shown in the following figure.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
364
Freescale Semiconductor, Inc.
Chapter 25 Analog comparator (ACMP)
DACREF
MUX
VDDA
Bandgap
ACE
6-bit
DAC
ACOPE
MUX
DACVAL
ACPSEL
DACEN
ACNSEL
+
External Output
–
MUX
ACMP0
ACMP1
ACMP2
Edge Control
Logic
HYST
ACO
ACMOD
Interrupt
ACF
ACIE
Figure 25-1. ACMP block diagram
25.2 External signal description
The output of ACMP can also be mapped to an external pin. When the output is mapped
to an external pin, ACMP_CS[ACOPE] controls the pin to enable/disable the ACMP
output function.
25.3 Memory map and register definition
ACMP memory map
Absolute
address
(hex)
Register name
Width
Access
(in bits)
Reset value
Section/
page
4007_3000
ACMP Control and Status Register (ACMP0_CS)
8
R/W
00h
25.3.1/366
4007_3001
ACMP Control Register 0 (ACMP0_C0)
8
R/W
00h
25.3.2/367
4007_3002
ACMP Control Register 1 (ACMP0_C1)
8
R/W
00h
25.3.3/367
4007_3003
ACMP Control Register 2 (ACMP0_C2)
8
R/W
00h
25.3.4/368
4007_4000
ACMP Control and Status Register (ACMP1_CS)
8
R/W
00h
25.3.1/366
4007_4001
ACMP Control Register 0 (ACMP1_C0)
8
R/W
00h
25.3.2/367
4007_4002
ACMP Control Register 1 (ACMP1_C1)
8
R/W
00h
25.3.3/367
4007_4003
ACMP Control Register 2 (ACMP1_C2)
8
R/W
00h
25.3.4/368
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
365
Memory map and register definition
25.3.1 ACMP Control and Status Register (ACMPx_CS)
Address: Base address + 0h offset
Bit
Read
Write
Reset
7
6
5
4
ACE
HYST
ACF
ACIE
0
0
0
0
3
ACO
0
2
1
ACOPE
0
ACMOD
0
0
0
ACMPx_CS field descriptions
Field
7
ACE
Description
Analog Comparator Enable
Enables the ACMP module.
0
1
6
HYST
The ACMP is disabled.
The ACMP is enabled.
Analog Comparator Hysterisis Selection
Selects ACMP hysterisis.
0
1
20 mV.
30 mV.
5
ACF
ACMP Interrupt Flag Bit
4
ACIE
ACMP Interrupt Enable
Synchronously set by hardware when ACMP output has a valid edge defined by ACMOD. The setting of
this bit lags the ACMPO to bus clocks. Clear ACF bit by writing a 0 to this bit. Writing a 1 to this bit has no
effect.
Enables an ACMP CPU interrupt.
0
1
3
ACO
2
ACOPE
ACMP Output
Reading ACO will return the current value of the analog comparator output. ACO is reset to a 0 and will
read as a 0 when the ACMP is disabled (ACE = 0)
ACMP Output Pin Enable
ACOPE enables the pad logic so that the output can be placed onto an external pin.
0
1
ACMOD
Disable the ACMP Interrupt.
Enable the ACMP Interrupt.
ACMP output cannot be placed onto external pin.
ACMP output can be placed onto external pin.
ACMP MOD
Determines the sensitivity modes of the interrupt trigger.
00
01
10
11
ACMP interrupt on output falling edge.
ACMP interrupt on output rising edge.
ACMP interrupt on output falling edge.
ACMP interrupt on output falling or rising edge.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
366
Freescale Semiconductor, Inc.
Chapter 25 Analog comparator (ACMP)
25.3.2 ACMP Control Register 0 (ACMPx_C0)
Address: Base address + 1h offset
Bit
Read
Write
Reset
7
6
5
0
4
3
2
ACPSEL
0
0
0
1
0
0
0
0
ACNSEL
0
0
0
2
1
0
0
0
0
ACMPx_C0 field descriptions
Field
Description
7–6
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
5–4
ACPSEL
ACMP Positive Input Select
3–2
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
ACNSEL
ACMP Negative Input Select
00
01
10
11
00
01
10
11
External reference 0
External reference 1
External reference 2
DAC output
External reference 0
External reference 1
External reference 2
DAC output
25.3.3 ACMP Control Register 1 (ACMPx_C1)
Address: Base address + 2h offset
Bit
Read
Write
Reset
7
6
DACEN
DACREF
0
0
5
4
3
DACVAL
0
0
0
ACMPx_C1 field descriptions
Field
7
DACEN
Description
DAC Enable
Enables the output of 6-bit DAC.
0
1
6
DACREF
The DAC is disabled.
The DAC is enabled.
DAC Reference Select
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
367
Functional description
ACMPx_C1 field descriptions (continued)
Field
Description
0
1
DACVAL
The DAC selects Bandgap as the reference.
The DAC selects VDDA as the reference.
DAC Output Level Selection
Selects the output voltage using the given formula: Voutput= (Vin/64)x(DACVAL[5:0]+1) The Voutput range is
from Vin/64 to Vin, the step is Vin/64
25.3.4 ACMP Control Register 2 (ACMPx_C2)
Address: Base address + 3h offset
Bit
Read
Write
Reset
7
6
5
4
3
2
1
0
0
0
0
0
ACIPE
0
0
0
0
0
ACMPx_C2 field descriptions
Field
7–3
Reserved
ACIPE
Description
This field is reserved.
This read-only field is reserved and always has the value 0.
ACMP Input Pin Enable
This 3-bit field controls if the corresponding ACMP external pin can be driven by an analog input.
0
1
The corresponding external analog input is not allowed.
The corresponding external analog input is allowed.
25.4 Functional description
The ACMP module is functionally composed of two parts: digital-to-analog (DAC) and
comparator (CMP).
The DAC includes a 64-level DAC (digital to analog converter) and relevant control
logic. DAC can select one of two reference inputs, VDD or on-chip bandgap, as the DAC
input Vin by setting ACMP_C1[DACREF]. After the DAC is enabled, it converts the data
set in ACMP_C1[DACVAL] to a stepped analog output, which is fed into ACMP as an
internal reference input. This stepped analog output is also mapped out of the module.
The output voltage range is from Vin/64 to Vin. The step size is Vin/64.
The ACMP can achieve the analog comparison between positive input and negative
input, and then give out a digital output and relevant interrupt. Both the positive and
negative input of ACMP can be selected from the four common inputs: three external
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
368
Freescale Semiconductor, Inc.
Chapter 25 Analog comparator (ACMP)
reference inputs and one internal reference input from the DAC output. The positive input
of ACMP is selected by ACMP_C0[ACPSEL] and the negative input is selected by
ACMP_C0[ACNSEL]. Any pair of the eight inputs can be compared by configuring the
ACMPC0 with the appropriate value.
After the ACMP is enabled by setting ACMP_CS[ACE], the comparison result appears
as a digital output. Whenever a valid edge defined in ACMP_CS[ACMOD] occurs,
ACMP_CS[ACF] is asserted. If ACMP_CS[ACIE] is set, a ACMP CPU interrupt occurs.
The valid edge is defined by ACMP_CS[ACMOD]. When ACMP_CS[ACMOD] = 00b
or 10b, only the falling-edge on ACMP output is valid. When ACMP_CS[ACMOD] =
01b, only rising-edge on ACMP output is valid. When ACMP_CS[ACMOD] = 11b, both
the rising-edge and falling-edge on the ACMP output are valid.
The ACMP output is synchronized by the bus clock to generate ACMP_CS[ACO] so that
the CPU can read the comparison. In stop3 mode, if the output of ACMP is changed,
ACMPO cannot be updated in time. The output can be synchronized and
ACMP_CS[ACO] can be updated upon the waking up of the CPU because of the
availability of the bus clock. ACMP_CS[ACO] changes following the comparison result,
so it can serve as a tracking flag that continuously indicates the voltage delta on the
inputs.
If a reference input external to the chip is selected as an input of ACMP, the
corresponding ACMP_C2[ACIPE] bit must be set to enable the input from pad interface.
If the output of the ACMP needs to be put onto the external pin, the ACMP_CS[ACOPE]
bit must enable the ACMP pin function of pad logic.
25.5 Setup and operation of ACMP
The two parts of ACMP (DAC and CMP) can be set up and operated independently. But
if the DAC works as an input of the CMP, the DAC must be configured before the
ACMP is enabled.
Because the input-switching can cause problems on the ACMP inputs, the user should
complete the input selection before enabling the ACMP and must not change the input
selection setting when the ACMP is enabled to avoid unexpected output. Similarly,
because the DAC experiences a setup delay after ACMP_C1[DACVAL] is changed, the
user should complete the setting of ACMP_C1[DACVAL] before DAC is enabled.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
369
Resets
25.6 Resets
During a reset the ACMP is configured in the default mode. Both CMP and DAC are
disabled.
25.7 Interrupts
If the bus clock is available when a valid edge defined in ACMP_CS[ACMOD] occurs,
the ACMP_CS[ACF] is asserted. If ACMP_CS[ACIE] is set, a ACMP interrupt event
occurs. The ACMP_CS[ACF] bit remains asserted until the ACMP interrupt is cleared by
software. When in stop mode, a valid edge on ACMP output generates an asynchronous
interrupt that can wake the MCU from stop. The interrupt can be cleared by writing a 0 to
the ACMP_CS[ACF] bit.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
370
Freescale Semiconductor, Inc.
Chapter 26
FlexTimer Module (FTM)
26.1 Introduction
NOTE
For the chip-specific implementation details of this module's
instances, see the chip configuration information.
The FlexTimer module (FTM) is a two-to-eight channel timer that supports input capture,
output compare, and the generation of PWM signals to control electric motor and power
management applications. The FTM time reference is a 16-bit counter that can be used as
an unsigned or signed counter.
26.1.1 FlexTimer philosophy
The FlexTimer is built upon a simple timer, the HCS08 Timer PWM Module – TPM,
used for many years on Freescale's 8-bit microcontrollers. The FlexTimer extends the
functionality to meet the demands of motor control, digital lighting solutions, and power
conversion, while providing low cost and backwards compatibility with the TPM module.
Several key enhancements are made:
•
•
•
•
•
Signed up counter
Deadtime insertion hardware
Fault control inputs
Enhanced triggering functionality
Initialization and polarity control
All of the features common with the TPM have fully backwards compatible register
assignments. The FlexTimer can also use code on the same core platform without change
to perform the same functions.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
371
Introduction
Motor control and power conversion features have been added through a dedicated set of
registers and defaults turn off all new features. The new features, such as hardware
deadtime insertion, polarity, fault control, and output forcing and masking, greatly reduce
loading on the execution software and are usually each controlled by a group of registers.
FlexTimer input triggers can be from comparators, ADC, or other submodules to initiate
timer functions automatically. These triggers can be linked in a variety of ways during
integration of the sub modules so please note the options available for used FlexTimer
configuration.
Several FlexTimers may be synchronized to provide a larger timer with their counters
incrementing in unison, assuming the initialization, the input clocks, the initial and final
counting values are the same in each FlexTimer.
All main user access registers are buffered to ease the load on the executing software. A
number of trigger options exist to determine which registers are updated with this user
defined data.
26.1.2 Features
The FTM features include:
• FTM source clock is selectable
• Source clock can be the system clock, the fixed frequency clock, or an external
clock
• Fixed frequency clock is an additional clock input to allow the selection of an on
chip clock source other than the system clock
• Selecting external clock connects FTM clock to a chip level input pin therefore
allowing to synchronize the FTM counter with an off chip clock source
• Prescaler divide-by 1, 2, 4, 8, 16, 32, 64, or 128
• 16-bit counter
• It can be a free-running counter or a counter with initial and final value
• The counting can be up or up-down
• Each channel can be configured for input capture, output compare, or edge-aligned
PWM mode
• In Input Capture mode:
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
372
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
• The capture can occur on rising edges, falling edges or both edges
• An input filter can be selected for some channels
• In Output Compare mode the output signal can be set, cleared, or toggled on match
• All channels can be configured for center-aligned PWM mode
• Each pair of channels can be combined to generate a PWM signal with independent
control of both edges of PWM signal
• The FTM channels can operate as pairs with equal outputs, pairs with
complementary outputs, or independent channels with independent outputs
• The deadtime insertion is available for each complementary pair
• Generation of match triggers
• Software control of PWM outputs
• Up to 4 fault inputs for global fault control
• The polarity of each channel is configurable
• The generation of an interrupt per channel
• The generation of an interrupt when the counter overflows
• The generation of an interrupt when the fault condition is detected
• Synchronized loading of write buffered FTM registers
• Write protection for critical registers
• Backwards compatible with TPM
• Testing of input captures for a stuck at zero and one conditions
• Dual edge capture for pulse and period width measurement
26.1.3 Modes of operation
When the MCU is in an active Debug mode, the FTM temporarily suspends all counting
until the MCU returns to normal user operating mode. During Stop mode, all FTM input
clocks are stopped, so the FTM is effectively disabled until clocks resume. During Wait
mode, the FTM continues to operate normally. If the FTM does not need to produce a
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
373
Introduction
real time reference or provide the interrupt sources needed to wake the MCU from Wait
mode, the power can then be saved by disabling FTM functions before entering Wait
mode.
26.1.4 Block diagram
The FTM uses one input/output (I/O) pin per channel, CHn (FTM channel (n)) where n is
the channel number (0–7).
The following figure shows the FTM structure. The central component of the FTM is the
16-bit counter with programmable initial and final values and its counting can be up or
up-down.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
374
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
CLKS
FTMEN
no clock selected
(FTM counter disable)
system clock
fixed frequency clock
external clock
PS
prescaler
(1, 2, 4, 8, 16, 32, 64 or 128)
synchronizer
CPWMS
CAPTEST
INITTRIGEN
CNTIN
FAULTM[1:0]
FFVAL[3:0]
FAULTIE
FAULTnEN*
FFLTRnEN*
FTM counter
CH0IE
CH0F
input capture
mode logic
C0V
input capture
mode logic
C1V
DECAPEN
COMBINE0
CPWMS
MS1B:MS1A
ELS1B:ELS1A
CH1F
CH0TRIG
channel 1
interrupt
CH1TRIG
channel 0
match trigger
channel 0
output signal
channel 1
output signal
channel 1
match trigger
pair channels 3 - channels 6 and 7
CH6IE
dual edge capture
mode logic
channel 7
input
channel 0
interrupt
output modes logic
(generation of channels 0 and 1 outputs signals in output
compare, EPWM, CPWM and combine modes according to
initialization, complementary mode, inverting, software output
control, deadtime insertion, output mask, fault control
and polarity control)
CH1IE
DECAPEN
COMBINE3
CPWMS
MS6B:MS6A
ELS6B:ELS6A
channel 6
input
fault condition
pair channels 0 - channels 0 and 1
dual edge capture
mode logic
channel 1
input
fault interrupt
*where n = 3, 2, 1, 0
DECAPEN
COMBINE0
CPWMS
MS0B:MS0A
ELS0B:ELS0A
timer overflow
interrupt
TOF
FAULTIN
FAULTF
FAULTFn*
fault control
fault input n*
channel 0
input
TOIE
MOD
initialization
trigger
CH6F
input capture
mode logic
C6V
input capture
mode logic
C7V
DECAPEN
COMBINE3
CPWMS
MS7B:MS7A
ELS7B:ELS7A
channel 6
interrupt
CH6TRIG
output modes logic
(generation of channels 6 and 7 outputs signals in output
compare, EPWM, CPWM and combine modes according to
initialization, complementary mode, inverting, software output
control, deadtime insertion, output mask, fault control
and polarity control)
CH7F
CH7IE
channel 7
interrupt
CH7TRIG
channel 6
match trigger
channel 6
output signal
channel 7
output signal
channel 7
match trigger
Figure 26-1. FTM block diagram
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
375
FTM signal descriptions
26.2 FTM signal descriptions
Table 26-1 shows the user-accessible signals for the FTM.
Table 26-1. FTM signal descriptions
Signal
Description
I/O
Function
EXTCLK
External clock. FTM external
clock can be selected to drive
the FTM counter.
I
The external clock input signal is used as the FTM counter
clock if selected by CLKS[1:0] bits in the SC register. This
clock signal must not exceed 1/4 of system clock frequency.
The FTM counter prescaler selection and settings are also
used when an external clock is selected.
CHn
FTM channel (n), where n can
be 7-0
I/O
Each FTM channel can be configured to operate either as
input or output. The direction associated with each channel,
input or output, is selected according to the mode assigned
for that channel.
FAULTj
Fault input (j), where j can be
3-0
I
The fault input signals are used to control the CHn channel
output state. If a fault is detected, the FAULTj signal is
asserted and the channel output is put in a safe state. The
behavior of the fault logic is defined by the FAULTM[1:0]
control bits in the MODE register and FAULTEN bit in the
COMBINEm register. Note that each FAULTj input may affect
all channels selectively since FAULTM[1:0] and FAULTEN
control bits are defined for each pair of channels. Because
there are several FAULTj inputs, maximum of 4 for the FTM
module, each one of these inputs is activated by the
FAULTjEN bit in the FLTCTRL register.
26.3 Memory map and register definition
26.3.1 Memory map
This section presents a high-level summary of the FTM registers and how they are
mapped.
The registers and bits of an unavailable function in the FTM remain in the memory map
and in the reset value, but they have no active function.
Note
Do not write in the region from the CNTIN register through the
PWMLOAD register when FTMEN = 0.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
376
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
26.3.2 Register descriptions
Accesses to reserved addresses result in transfer errors. Registers for absent channels are
considered reserved.
FTM memory map
Absolute
address
(hex)
Register name
Width
Access
(in bits)
Reset value
Section/
page
4003_8000
Status And Control (FTM0_SC)
32
R/W
0000_0000h
26.3.3/380
4003_8004
Counter (FTM0_CNT)
32
R/W
0000_0000h
26.3.4/382
4003_8008
Modulo (FTM0_MOD)
32
R/W
0000_0000h
26.3.5/382
4003_800C
Channel (n) Status And Control (FTM0_C0SC)
32
R/W
0000_0000h
26.3.6/383
4003_8010
Channel (n) Value (FTM0_C0V)
32
R/W
0000_0000h
26.3.7/385
4003_8014
Channel (n) Status And Control (FTM0_C1SC)
32
R/W
0000_0000h
26.3.6/383
4003_8018
Channel (n) Value (FTM0_C1V)
32
R/W
0000_0000h
26.3.7/385
4003_801C
Channel (n) Status And Control (FTM0_C2SC)
32
R/W
0000_0000h
26.3.6/383
4003_8020
Channel (n) Value (FTM0_C2V)
32
R/W
0000_0000h
26.3.7/385
4003_8024
Channel (n) Status And Control (FTM0_C3SC)
32
R/W
0000_0000h
26.3.6/383
4003_8028
Channel (n) Value (FTM0_C3V)
32
R/W
0000_0000h
26.3.7/385
4003_802C
Channel (n) Status And Control (FTM0_C4SC)
32
R/W
0000_0000h
26.3.6/383
4003_8030
Channel (n) Value (FTM0_C4V)
32
R/W
0000_0000h
26.3.7/385
4003_8034
Channel (n) Status And Control (FTM0_C5SC)
32
R/W
0000_0000h
26.3.6/383
4003_8038
Channel (n) Value (FTM0_C5V)
32
R/W
0000_0000h
26.3.7/385
4003_803C
Channel (n) Status And Control (FTM0_C6SC)
32
R/W
0000_0000h
26.3.6/383
4003_8040
Channel (n) Value (FTM0_C6V)
32
R/W
0000_0000h
26.3.7/385
4003_8044
Channel (n) Status And Control (FTM0_C7SC)
32
R/W
0000_0000h
26.3.6/383
4003_8048
Channel (n) Value (FTM0_C7V)
32
R/W
0000_0000h
26.3.7/385
4003_804C
Counter Initial Value (FTM0_CNTIN)
32
R/W
0000_0000h
26.3.8/386
4003_8050
Capture And Compare Status (FTM0_STATUS)
32
R/W
0000_0000h
26.3.9/387
4003_8054
Features Mode Selection (FTM0_MODE)
32
R/W
0000_0004h
26.3.10/389
4003_8058
Synchronization (FTM0_SYNC)
32
R/W
0000_0000h
26.3.11/390
4003_805C
Initial State For Channels Output (FTM0_OUTINIT)
32
R/W
0000_0000h
26.3.12/393
4003_8060
Output Mask (FTM0_OUTMASK)
32
R/W
0000_0000h
26.3.13/394
4003_8064
Function For Linked Channels (FTM0_COMBINE)
32
R/W
0000_0000h
26.3.14/396
4003_8068
Deadtime Insertion Control (FTM0_DEADTIME)
32
R/W
0000_0000h
26.3.15/401
4003_806C
FTM External Trigger (FTM0_EXTTRIG)
32
R/W
0000_0000h
26.3.16/402
4003_8070
Channels Polarity (FTM0_POL)
32
R/W
0000_0000h
26.3.17/404
4003_8074
Fault Mode Status (FTM0_FMS)
32
R/W
0000_0000h
26.3.18/406
4003_8078
Input Capture Filter Control (FTM0_FILTER)
32
R/W
0000_0000h
26.3.19/408
4003_807C
Fault Control (FTM0_FLTCTRL)
32
R/W
0000_0000h
26.3.20/409
4003_8084
Configuration (FTM0_CONF)
32
R/W
0000_0000h
26.3.21/411
4003_8088
FTM Fault Input Polarity (FTM0_FLTPOL)
32
R/W
0000_0000h
26.3.22/412
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
377
Memory map and register definition
FTM memory map (continued)
Absolute
address
(hex)
Register name
Width
Access
(in bits)
Reset value
Section/
page
4003_808C
Synchronization Configuration (FTM0_SYNCONF)
32
R/W
0000_0000h
26.3.23/414
4003_8090
FTM Inverting Control (FTM0_INVCTRL)
32
R/W
0000_0000h
26.3.24/416
4003_8094
FTM Software Output Control (FTM0_SWOCTRL)
32
R/W
0000_0000h
26.3.25/417
4003_8098
FTM PWM Load (FTM0_PWMLOAD)
32
R/W
0000_0000h
26.3.26/419
4003_9000
Status And Control (FTM1_SC)
32
R/W
0000_0000h
26.3.3/380
4003_9004
Counter (FTM1_CNT)
32
R/W
0000_0000h
26.3.4/382
4003_9008
Modulo (FTM1_MOD)
32
R/W
0000_0000h
26.3.5/382
4003_900C
Channel (n) Status And Control (FTM1_C0SC)
32
R/W
0000_0000h
26.3.6/383
4003_9010
Channel (n) Value (FTM1_C0V)
32
R/W
0000_0000h
26.3.7/385
4003_9014
Channel (n) Status And Control (FTM1_C1SC)
32
R/W
0000_0000h
26.3.6/383
4003_9018
Channel (n) Value (FTM1_C1V)
32
R/W
0000_0000h
26.3.7/385
4003_901C
Channel (n) Status And Control (FTM1_C2SC)
32
R/W
0000_0000h
26.3.6/383
4003_9020
Channel (n) Value (FTM1_C2V)
32
R/W
0000_0000h
26.3.7/385
4003_9024
Channel (n) Status And Control (FTM1_C3SC)
32
R/W
0000_0000h
26.3.6/383
4003_9028
Channel (n) Value (FTM1_C3V)
32
R/W
0000_0000h
26.3.7/385
4003_902C
Channel (n) Status And Control (FTM1_C4SC)
32
R/W
0000_0000h
26.3.6/383
4003_9030
Channel (n) Value (FTM1_C4V)
32
R/W
0000_0000h
26.3.7/385
4003_9034
Channel (n) Status And Control (FTM1_C5SC)
32
R/W
0000_0000h
26.3.6/383
4003_9038
Channel (n) Value (FTM1_C5V)
32
R/W
0000_0000h
26.3.7/385
4003_903C
Channel (n) Status And Control (FTM1_C6SC)
32
R/W
0000_0000h
26.3.6/383
4003_9040
Channel (n) Value (FTM1_C6V)
32
R/W
0000_0000h
26.3.7/385
4003_9044
Channel (n) Status And Control (FTM1_C7SC)
32
R/W
0000_0000h
26.3.6/383
4003_9048
Channel (n) Value (FTM1_C7V)
32
R/W
0000_0000h
26.3.7/385
4003_904C
Counter Initial Value (FTM1_CNTIN)
32
R/W
0000_0000h
26.3.8/386
4003_9050
Capture And Compare Status (FTM1_STATUS)
32
R/W
0000_0000h
26.3.9/387
4003_9054
Features Mode Selection (FTM1_MODE)
32
R/W
0000_0004h
26.3.10/389
4003_9058
Synchronization (FTM1_SYNC)
32
R/W
0000_0000h
26.3.11/390
4003_905C
Initial State For Channels Output (FTM1_OUTINIT)
32
R/W
0000_0000h
26.3.12/393
4003_9060
Output Mask (FTM1_OUTMASK)
32
R/W
0000_0000h
26.3.13/394
4003_9064
Function For Linked Channels (FTM1_COMBINE)
32
R/W
0000_0000h
26.3.14/396
4003_9068
Deadtime Insertion Control (FTM1_DEADTIME)
32
R/W
0000_0000h
26.3.15/401
4003_906C
FTM External Trigger (FTM1_EXTTRIG)
32
R/W
0000_0000h
26.3.16/402
4003_9070
Channels Polarity (FTM1_POL)
32
R/W
0000_0000h
26.3.17/404
4003_9074
Fault Mode Status (FTM1_FMS)
32
R/W
0000_0000h
26.3.18/406
4003_9078
Input Capture Filter Control (FTM1_FILTER)
32
R/W
0000_0000h
26.3.19/408
4003_907C
Fault Control (FTM1_FLTCTRL)
32
R/W
0000_0000h
26.3.20/409
4003_9084
Configuration (FTM1_CONF)
32
R/W
0000_0000h
26.3.21/411
4003_9088
FTM Fault Input Polarity (FTM1_FLTPOL)
32
R/W
0000_0000h
26.3.22/412
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
378
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
FTM memory map (continued)
Absolute
address
(hex)
Register name
Width
Access
(in bits)
Reset value
Section/
page
4003_908C
Synchronization Configuration (FTM1_SYNCONF)
32
R/W
0000_0000h
26.3.23/414
4003_9090
FTM Inverting Control (FTM1_INVCTRL)
32
R/W
0000_0000h
26.3.24/416
4003_9094
FTM Software Output Control (FTM1_SWOCTRL)
32
R/W
0000_0000h
26.3.25/417
4003_9098
FTM PWM Load (FTM1_PWMLOAD)
32
R/W
0000_0000h
26.3.26/419
4003_A000
Status And Control (FTM2_SC)
32
R/W
0000_0000h
26.3.3/380
4003_A004
Counter (FTM2_CNT)
32
R/W
0000_0000h
26.3.4/382
4003_A008
Modulo (FTM2_MOD)
32
R/W
0000_0000h
26.3.5/382
4003_A00C Channel (n) Status And Control (FTM2_C0SC)
32
R/W
0000_0000h
26.3.6/383
4003_A010
Channel (n) Value (FTM2_C0V)
32
R/W
0000_0000h
26.3.7/385
4003_A014
Channel (n) Status And Control (FTM2_C1SC)
32
R/W
0000_0000h
26.3.6/383
4003_A018
Channel (n) Value (FTM2_C1V)
32
R/W
0000_0000h
26.3.7/385
4003_A01C Channel (n) Status And Control (FTM2_C2SC)
32
R/W
0000_0000h
26.3.6/383
4003_A020
Channel (n) Value (FTM2_C2V)
32
R/W
0000_0000h
26.3.7/385
4003_A024
Channel (n) Status And Control (FTM2_C3SC)
32
R/W
0000_0000h
26.3.6/383
4003_A028
Channel (n) Value (FTM2_C3V)
32
R/W
0000_0000h
26.3.7/385
4003_A02C Channel (n) Status And Control (FTM2_C4SC)
32
R/W
0000_0000h
26.3.6/383
4003_A030
Channel (n) Value (FTM2_C4V)
32
R/W
0000_0000h
26.3.7/385
4003_A034
Channel (n) Status And Control (FTM2_C5SC)
32
R/W
0000_0000h
26.3.6/383
4003_A038
Channel (n) Value (FTM2_C5V)
32
R/W
0000_0000h
26.3.7/385
4003_A03C Channel (n) Status And Control (FTM2_C6SC)
32
R/W
0000_0000h
26.3.6/383
4003_A040
Channel (n) Value (FTM2_C6V)
32
R/W
0000_0000h
26.3.7/385
4003_A044
Channel (n) Status And Control (FTM2_C7SC)
32
R/W
0000_0000h
26.3.6/383
4003_A048
Channel (n) Value (FTM2_C7V)
32
R/W
0000_0000h
26.3.7/385
4003_A04C Counter Initial Value (FTM2_CNTIN)
32
R/W
0000_0000h
26.3.8/386
4003_A050
Capture And Compare Status (FTM2_STATUS)
32
R/W
0000_0000h
26.3.9/387
4003_A054
Features Mode Selection (FTM2_MODE)
32
R/W
0000_0004h
26.3.10/389
4003_A058
Synchronization (FTM2_SYNC)
32
R/W
0000_0000h
26.3.11/390
4003_A05C Initial State For Channels Output (FTM2_OUTINIT)
32
R/W
0000_0000h
26.3.12/393
4003_A060
Output Mask (FTM2_OUTMASK)
32
R/W
0000_0000h
26.3.13/394
4003_A064
Function For Linked Channels (FTM2_COMBINE)
32
R/W
0000_0000h
26.3.14/396
4003_A068
Deadtime Insertion Control (FTM2_DEADTIME)
32
R/W
0000_0000h
26.3.15/401
4003_A06C FTM External Trigger (FTM2_EXTTRIG)
32
R/W
0000_0000h
26.3.16/402
4003_A070
Channels Polarity (FTM2_POL)
32
R/W
0000_0000h
26.3.17/404
4003_A074
Fault Mode Status (FTM2_FMS)
32
R/W
0000_0000h
26.3.18/406
4003_A078
Input Capture Filter Control (FTM2_FILTER)
32
R/W
0000_0000h
26.3.19/408
4003_A07C Fault Control (FTM2_FLTCTRL)
32
R/W
0000_0000h
26.3.20/409
4003_A084
Configuration (FTM2_CONF)
32
R/W
0000_0000h
26.3.21/411
4003_A088
FTM Fault Input Polarity (FTM2_FLTPOL)
32
R/W
0000_0000h
26.3.22/412
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
379
Memory map and register definition
FTM memory map (continued)
Absolute
address
(hex)
Width
Access
(in bits)
Register name
Reset value
Section/
page
4003_A08C Synchronization Configuration (FTM2_SYNCONF)
32
R/W
0000_0000h
26.3.23/414
4003_A090
FTM Inverting Control (FTM2_INVCTRL)
32
R/W
0000_0000h
26.3.24/416
4003_A094
FTM Software Output Control (FTM2_SWOCTRL)
32
R/W
0000_0000h
26.3.25/417
4003_A098
FTM PWM Load (FTM2_PWMLOAD)
32
R/W
0000_0000h
26.3.26/419
26.3.3 Status And Control (FTMx_SC)
SC contains the overflow status flag and control bits used to configure the interrupt
enable, FTM configuration, clock source, and prescaler factor. These controls relate to all
channels within this module.
Address: Base address + 0h offset
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
0
R
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
TOIE
0
0
TOF
Reset
CPWMS
W
0
R
PS
0
W
Reset
CLKS
0
0
0
0
0
0
0
0
0
0
0
0
0
0
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
380
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
FTMx_SC field descriptions
Field
31–8
Reserved
7
TOF
Description
This field is reserved.
This read-only field is reserved and always has the value 0.
Timer Overflow Flag
Set by hardware when the FTM counter passes the value in the MOD register. The TOF bit is cleared by
reading the SC register while TOF is set and then writing a 0 to TOF bit. Writing a 1 to TOF has no effect.
If another FTM overflow occurs between the read and write operations, the write operation has no effect;
therefore, TOF remains set indicating an overflow has occurred. In this case, a TOF interrupt request is
not lost due to the clearing sequence for a previous TOF.
0
1
6
TOIE
Timer Overflow Interrupt Enable
Enables FTM overflow interrupts.
0
1
5
CPWMS
FTM counter has not overflowed.
FTM counter has overflowed.
Disable TOF interrupts. Use software polling.
Enable TOF interrupts. An interrupt is generated when TOF equals one.
Center-Aligned PWM Select
Selects CPWM mode. This mode configures the FTM to operate in Up-Down Counting mode.
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0
1
4–3
CLKS
FTM counter operates in Up Counting mode.
FTM counter operates in Up-Down Counting mode.
Clock Source Selection
Selects one of the three FTM counter clock sources.
This field is write protected. It can be written only when MODE[WPDIS] = 1.
00
01
10
11
PS
No clock selected. This in effect disables the FTM counter.
System clock
Fixed frequency clock
External clock
Prescale Factor Selection
Selects one of 8 division factors for the clock source selected by CLKS. The new prescaler factor affects
the clock source on the next system clock cycle after the new value is updated into the register bits.
This field is write protected. It can be written only when MODE[WPDIS] = 1.
000
001
010
011
100
101
110
111
Divide by 1
Divide by 2
Divide by 4
Divide by 8
Divide by 16
Divide by 32
Divide by 64
Divide by 128
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
381
Memory map and register definition
26.3.4 Counter (FTMx_CNT)
The CNT register contains the FTM counter value.
Reset clears the CNT register. Writing any value to COUNT updates the counter with its
initial value, CNTIN.
When Debug is active, the FTM counter is frozen. This is the value that you may read.
Address: Base address + 4h offset
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
0
R
0
0
0
0
0
0
0
0
7
6
5
4
3
2
1
0
0
0
0
0
0
0
0
COUNT
W
Reset
8
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
FTMx_CNT field descriptions
Field
Description
31–16
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
COUNT
Counter Value
26.3.5 Modulo (FTMx_MOD)
The Modulo register contains the modulo value for the FTM counter. After the FTM
counter reaches the modulo value, the overflow flag (TOF) becomes set at the next clock,
and the next value of FTM counter depends on the selected counting method; see
Counter.
Writing to the MOD register latches the value into a buffer. The MOD register is updated
with the value of its write buffer according to Registers updated from write buffers.
If FTMEN = 0, this write coherency mechanism may be manually reset by writing to the
SC register whether Debug is active or not.
Initialize the FTM counter, by writing to CNT, before writing to the MOD register to
avoid confusion about when the first counter overflow will occur.
Address: Base address + 8h offset
Bit
R
W
31
Reset
0
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
Reserved
0
0
0
0
0
0
0
0
8
7
6
5
4
3
2
1
0
0
0
0
0
0
0
0
MOD
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
382
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
FTMx_MOD field descriptions
Field
31–16
Reserved
MOD
Description
This field is reserved.
Modulo Value
26.3.6 Channel (n) Status And Control (FTMx_CnSC)
CnSC contains the channel-interrupt-status flag and control bits used to configure the
interrupt enable, channel configuration, and pin function.
Table 26-69. Mode, edge, and level selection
DECAPEN
COMBINE
CPWMS
MSnB:MSnA
ELSnB:ELSnA
X
X
X
XX
0
0
0
0
0
1
1
1X
Mode
Pin not used for FTM—revert the
channel pin to general purpose I/O
or other peripheral control
Input Capture
XX
Capture on
Rising Edge
Only
10
Capture on
Falling Edge
Only
11
Capture on
Rising or Falling
Edge
1
Output Compare
Toggle Output
on match
10
Clear Output on
match
11
Set Output on
match
10
Edge-Aligned
PWM
X1
1
Configuration
10
High-true pulses
(clear Output on
match)
Low-true pulses
(set Output on
match)
Center-Aligned
PWM
X1
High-true pulses
(clear Output on
match-up)
Low-true pulses
(set Output on
match-up)
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
383
Memory map and register definition
Table 26-69. Mode, edge, and level selection (continued)
DECAPEN
1
COMBINE
CPWMS
MSnB:MSnA
ELSnB:ELSnA
1
0
XX
10
Combine PWM High-true pulses
(set on channel
(n) match, and
clear on channel
(n+1) match)
X1
Low-true pulses
(clear on
channel (n)
match, and set
on channel (n
+1) match)
0
0
X0
Mode
See the
following table
(Table 26-8).
X1
Configuration
Dual Edge
Capture
One-Shot
Capture mode
Continuous
Capture mode
Table 26-70. Dual Edge Capture mode — edge polarity selection
ELSnB
ELSnA
Channel Port Enable
Detected Edges
0
0
Disabled
No edge
0
1
Enabled
Rising edge
1
0
Enabled
Falling edge
1
1
Enabled
Rising and falling edges
Address: Base address + Ch offset + (8d × i), where i=0d to 7d
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
0
R
W
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
CHIE
MSB
0
0
0
0
0
0
0
R
CHF
0
W
Reset
0
0
0
0
0
0
0
0
0
MSA ELSB ELSA
0
0
0
FTMx_CnSC field descriptions
Field
31–8
Reserved
7
CHF
Description
This field is reserved.
This read-only field is reserved and always has the value 0.
Channel Flag
Set by hardware when an event occurs on the channel. CHF is cleared by reading the CSC register while
CHnF is set and then writing a 0 to the CHF bit. Writing a 1 to CHF has no effect.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
384
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
FTMx_CnSC field descriptions (continued)
Field
Description
If another event occurs between the read and write operations, the write operation has no effect; therefore,
CHF remains set indicating an event has occurred. In this case a CHF interrupt request is not lost due to
the clearing sequence for a previous CHF.
0
1
6
CHIE
Channel Interrupt Enable
Enables channel interrupts.
0
1
5
MSB
No channel event has occurred.
A channel event has occurred.
Disable channel interrupts. Use software polling.
Enable channel interrupts.
Channel Mode Select
Used for further selections in the channel logic. Its functionality is dependent on the channel mode. See
Table 26-7.
This field is write protected. It can be written only when MODE[WPDIS] = 1.
4
MSA
Channel Mode Select
Used for further selections in the channel logic. Its functionality is dependent on the channel mode. See
Table 26-7.
This field is write protected. It can be written only when MODE[WPDIS] = 1.
3
ELSB
Edge or Level Select
The functionality of ELSB and ELSA depends on the channel mode. See Table 26-7.
This field is write protected. It can be written only when MODE[WPDIS] = 1.
2
ELSA
Edge or Level Select
The functionality of ELSB and ELSA depends on the channel mode. See Table 26-7.
This field is write protected. It can be written only when MODE[WPDIS] = 1.
1
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
0
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
26.3.7 Channel (n) Value (FTMx_CnV)
These registers contain the captured FTM counter value for the input modes or the match
value for the output modes.
In Input Capture, Capture Test, and Dual Edge Capture modes, any write to a CnV
register is ignored.
In output modes, writing to a CnV register latches the value into a buffer. A CnV register
is updated with the value of its write buffer according to Registers updated from write
buffers.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
385
Memory map and register definition
If FTMEN = 0, this write coherency mechanism may be manually reset by writing to the
CnSC register whether Debug mode is active or not.
Address: Base address + 10h offset + (8d × i), where i=0d to 7d
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
0
R
0
0
0
0
0
0
0
0
7
6
5
4
3
2
1
0
0
0
0
0
0
0
0
VAL
W
Reset
8
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
FTMx_CnV field descriptions
Field
Description
31–16
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
VAL
Channel Value
Captured FTM counter value of the input modes or the match value for the output modes
26.3.8 Counter Initial Value (FTMx_CNTIN)
The Counter Initial Value register contains the initial value for the FTM counter.
Writing to the CNTIN register latches the value into a buffer. The CNTIN register is
updated with the value of its write buffer according to Registers updated from write
buffers.
When the FTM clock is initially selected, by writing a non-zero value to the CLKS bits,
the FTM counter starts with the value 0x0000. To avoid this behavior, before the first
write to select the FTM clock, write the new value to the the CNTIN register and then
initialize the FTM counter by writing any value to the CNT register.
Address: Base address + 4Ch offset
Bit
R
W
31
Reset
0
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
Reserved
0
0
0
0
0
0
0
0
8
7
6
5
4
3
2
1
0
0
0
0
0
0
0
0
INIT
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
FTMx_CNTIN field descriptions
Field
31–16
Reserved
INIT
Description
This field is reserved.
Initial Value Of The FTM Counter
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
386
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
26.3.9 Capture And Compare Status (FTMx_STATUS)
The STATUS register contains a copy of the status flag CHnF bit in CnSC for each FTM
channel for software convenience.
Each CHnF bit in STATUS is a mirror of CHnF bit in CnSC. All CHnF bits can be
checked using only one read of STATUS. All CHnF bits can be cleared by reading
STATUS followed by writing 0x00 to STATUS.
Hardware sets the individual channel flags when an event occurs on the channel. CHnF is
cleared by reading STATUS while CHnF is set and then writing a 0 to the CHnF bit.
Writing a 1 to CHnF has no effect.
If another event occurs between the read and write operations, the write operation has no
effect; therefore, CHnF remains set indicating an event has occurred. In this case, a CHnF
interrupt request is not lost due to the clearing sequence for a previous CHnF.
NOTE
The STATUS register should be used only in Combine mode.
Address: Base address + 50h offset
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
0
R
W
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
0
R
W
Reset
0
0
0
0
0
0
0
0
CH0F
0
CH1F
0
CH2F
0
CH3F
0
CH4F
0
CH5F
0
CH6F
0
CH7F
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
387
Memory map and register definition
FTMx_STATUS field descriptions
Field
31–8
Reserved
7
CH7F
Description
This field is reserved.
This read-only field is reserved and always has the value 0.
Channel 7 Flag
See the register description.
0
1
6
CH6F
Channel 6 Flag
See the register description.
0
1
5
CH5F
See the register description.
See the register description.
See the register description.
See the register description.
No channel event has occurred.
A channel event has occurred.
Channel 1 Flag
See the register description.
0
1
0
CH0F
No channel event has occurred.
A channel event has occurred.
Channel 2 Flag
0
1
1
CH1F
No channel event has occurred.
A channel event has occurred.
Channel 3 Flag
0
1
2
CH2F
No channel event has occurred.
A channel event has occurred.
Channel 4 Flag
0
1
3
CH3F
No channel event has occurred.
A channel event has occurred.
Channel 5 Flag
0
1
4
CH4F
No channel event has occurred.
A channel event has occurred.
No channel event has occurred.
A channel event has occurred.
Channel 0 Flag
See the register description.
0
1
No channel event has occurred.
A channel event has occurred.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
388
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
26.3.10 Features Mode Selection (FTMx_MODE)
This register contains the global enable bit for FTM-specific features and the control bits
used to configure:
•
•
•
•
•
Fault control mode and interrupt
Capture Test mode
PWM synchronization
Write protection
Channel output initialization
These controls relate to all channels within this module.
Address: Base address + 54h offset
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
0
R
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
CAPTEST
PWMSYNC
WPDIS
INIT
FTMEN
W
0
0
1
0
0
FAULTIE
0
R
W
Reset
0
0
0
0
0
0
0
0
0
FAULTM
0
0
FTMx_MODE field descriptions
Field
Description
31–8
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
7
FAULTIE
Fault Interrupt Enable
Enables the generation of an interrupt when a fault is detected by FTM and the FTM fault control is
enabled.
0
1
6–5
FAULTM
Fault control interrupt is disabled.
Fault control interrupt is enabled.
Fault Control Mode
Defines the FTM fault control mode.
This field is write protected. It can be written only when MODE[WPDIS] = 1.
00
01
Fault control is disabled for all channels.
Fault control is enabled for even channels only (channels 0, 2, 4, and 6), and the selected mode is
the manual fault clearing.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
389
Memory map and register definition
FTMx_MODE field descriptions (continued)
Field
Description
10
11
4
CAPTEST
Fault control is enabled for all channels, and the selected mode is the manual fault clearing.
Fault control is enabled for all channels, and the selected mode is the automatic fault clearing.
Capture Test Mode Enable
Enables the capture test mode.
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0
1
3
PWMSYNC
PWM Synchronization Mode
Selects which triggers can be used by MOD, CnV, OUTMASK, and FTM counter synchronization. See
PWM synchronization. The PWMSYNC bit configures the synchronization when SYNCMODE is 0.
0
1
2
WPDIS
No restrictions. Software and hardware triggers can be used by MOD, CnV, OUTMASK, and FTM
counter synchronization.
Software trigger can only be used by MOD and CnV synchronization, and hardware triggers can only
be used by OUTMASK and FTM counter synchronization.
Write Protection Disable
When write protection is enabled (WPDIS = 0), write protected bits cannot be written. When write
protection is disabled (WPDIS = 1), write protected bits can be written. The WPDIS bit is the negation of
the WPEN bit. WPDIS is cleared when 1 is written to WPEN. WPDIS is set when WPEN bit is read as a 1
and then 1 is written to WPDIS. Writing 0 to WPDIS has no effect.
0
1
1
INIT
Capture test mode is disabled.
Capture test mode is enabled.
Write protection is enabled.
Write protection is disabled.
Initialize The Channels Output
When a 1 is written to INIT bit the channels output is initialized according to the state of their
corresponding bit in the OUTINIT register. Writing a 0 to INIT bit has no effect.
The INIT bit is always read as 0.
0
FTMEN
FTM Enable
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0
1
Only the TPM-compatible registers (first set of registers) can be used without any restriction. Do not
use the FTM-specific registers.
All registers including the FTM-specific registers (second set of registers) are available for use with no
restrictions.
26.3.11 Synchronization (FTMx_SYNC)
This register configures the PWM synchronization.
A synchronization event can perform the synchronized update of MOD, CV, and
OUTMASK registers with the value of their write buffer and the FTM counter
initialization.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
390
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
NOTE
The software trigger, SWSYNC bit, and hardware triggers
TRIG0, TRIG1, and TRIG2 bits have a potential conflict if
used together when SYNCMODE = 0. Use only hardware or
software triggers but not both at the same time, otherwise
unpredictable behavior is likely to happen.
The selection of the loading point, CNTMAX and CNTMIN
bits, is intended to provide the update of MOD, CNTIN, and
CnV registers across all enabled channels simultaneously. The
use of the loading point selection together with SYNCMODE =
0 and hardware trigger selection, TRIG0, TRIG1, or TRIG2
bits, is likely to result in unpredictable behavior.
The synchronization event selection also depends on the
PWMSYNC (MODE register) and SYNCMODE (SYNCONF
register) bits. See PWM synchronization.
Address: Base address + 58h offset
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
0
R
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
SWSYNC
TRIG2
TRIG1
TRIG0
SYNCHOM
REINIT
CNTMAX
CNTMIN
W
0
0
0
0
0
0
0
0
0
0
0
0
0
R
W
Reset
0
0
0
0
FTMx_SYNC field descriptions
Field
Description
31–8
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
7
SWSYNC
PWM Synchronization Software Trigger
Selects the software trigger as the PWM synchronization trigger. The software trigger happens when a 1 is
written to SWSYNC bit.
0
1
6
TRIG2
Software trigger is not selected.
Software trigger is selected.
PWM Synchronization Hardware Trigger 2
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
391
Memory map and register definition
FTMx_SYNC field descriptions (continued)
Field
Description
Enables hardware trigger 2 to the PWM synchronization. Hardware trigger 2 happens when a rising edge
is detected at the trigger 2 input signal.
0
1
5
TRIG1
PWM Synchronization Hardware Trigger 1
Enables hardware trigger 1 to the PWM synchronization. Hardware trigger 1 happens when a rising edge
is detected at the trigger 1 input signal.
0
1
4
TRIG0
Enables hardware trigger 0 to the PWM synchronization. Hardware trigger 0 occurs when a rising edge is
detected at the trigger 0 input signal.
Selects when the OUTMASK register is updated with the value of its buffer.
Determines if the FTM counter is reinitialized when the selected trigger for the synchronization is detected.
The REINIT bit configures the synchronization when SYNCMODE is zero.
FTM counter continues to count normally.
FTM counter is updated with its initial value when the selected trigger is detected.
Maximum Loading Point Enable
Selects the maximum loading point to PWM synchronization. See Boundary cycle and loading points. If
CNTMAX is 1, the selected loading point is when the FTM counter reaches its maximum value (MOD
register).
0
1
0
CNTMIN
OUTMASK register is updated with the value of its buffer in all rising edges of the system clock.
OUTMASK register is updated with the value of its buffer only by the PWM synchronization.
FTM Counter Reinitialization By Synchronization (FTM counter synchronization)
0
1
1
CNTMAX
Trigger is disabled.
Trigger is enabled.
Output Mask Synchronization
0
1
2
REINIT
Trigger is disabled.
Trigger is enabled.
PWM Synchronization Hardware Trigger 0
0
1
3
SYNCHOM
Trigger is disabled.
Trigger is enabled.
The maximum loading point is disabled.
The maximum loading point is enabled.
Minimum Loading Point Enable
Selects the minimum loading point to PWM synchronization. See Boundary cycle and loading points. If
CNTMIN is one, the selected loading point is when the FTM counter reaches its minimum value (CNTIN
register).
0
1
The minimum loading point is disabled.
The minimum loading point is enabled.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
392
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
26.3.12 Initial State For Channels Output (FTMx_OUTINIT)
Address: Base address + 5Ch offset
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
0
R
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
CH7OI
CH6OI
CH5OI
CH4OI
CH3OI
CH2OI
CH1OI
CH0OI
W
0
0
0
0
0
0
0
0
0
0
0
0
0
R
W
Reset
0
0
0
0
FTMx_OUTINIT field descriptions
Field
31–8
Reserved
7
CH7OI
Description
This field is reserved.
This read-only field is reserved and always has the value 0.
Channel 7 Output Initialization Value
Selects the value that is forced into the channel output when the initialization occurs.
0
1
6
CH6OI
Channel 6 Output Initialization Value
Selects the value that is forced into the channel output when the initialization occurs.
0
1
5
CH5OI
Selects the value that is forced into the channel output when the initialization occurs.
The initialization value is 0.
The initialization value is 1.
Channel 4 Output Initialization Value
Selects the value that is forced into the channel output when the initialization occurs.
0
1
3
CH3OI
The initialization value is 0.
The initialization value is 1.
Channel 5 Output Initialization Value
0
1
4
CH4OI
The initialization value is 0.
The initialization value is 1.
The initialization value is 0.
The initialization value is 1.
Channel 3 Output Initialization Value
Selects the value that is forced into the channel output when the initialization occurs.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
393
Memory map and register definition
FTMx_OUTINIT field descriptions (continued)
Field
Description
0
1
2
CH2OI
The initialization value is 0.
The initialization value is 1.
Channel 2 Output Initialization Value
Selects the value that is forced into the channel output when the initialization occurs.
0
1
1
CH1OI
The initialization value is 0.
The initialization value is 1.
Channel 1 Output Initialization Value
Selects the value that is forced into the channel output when the initialization occurs.
0
1
0
CH0OI
The initialization value is 0.
The initialization value is 1.
Channel 0 Output Initialization Value
Selects the value that is forced into the channel output when the initialization occurs.
0
1
The initialization value is 0.
The initialization value is 1.
26.3.13 Output Mask (FTMx_OUTMASK)
This register provides a mask for each FTM channel. The mask of a channel determines if
its output responds, that is, it is masked or not, when a match occurs. This feature is used
for BLDC control where the PWM signal is presented to an electric motor at specific
times to provide electronic commutation.
Any write to the OUTMASK register, stores the value in its write buffer. The register is
updated with the value of its write buffer according to PWM synchronization.
Address: Base address + 60h offset
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
0
R
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
CH7OM
CH6OM
CH5OM
CH4OM
CH3OM
CH2OM
CH1OM
CH0OM
W
0
0
0
0
0
0
0
0
0
0
0
0
0
R
W
Reset
0
0
0
0
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
394
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
FTMx_OUTMASK field descriptions
Field
31–8
Reserved
7
CH7OM
Description
This field is reserved.
This read-only field is reserved and always has the value 0.
Channel 7 Output Mask
Defines if the channel output is masked or unmasked.
0
1
6
CH6OM
Channel 6 Output Mask
Defines if the channel output is masked or unmasked.
0
1
5
CH5OM
Defines if the channel output is masked or unmasked.
Defines if the channel output is masked or unmasked.
Defines if the channel output is masked or unmasked.
Defines if the channel output is masked or unmasked.
Channel output is not masked. It continues to operate normally.
Channel output is masked. It is forced to its inactive state.
Channel 1 Output Mask
Defines if the channel output is masked or unmasked.
0
1
0
CH0OM
Channel output is not masked. It continues to operate normally.
Channel output is masked. It is forced to its inactive state.
Channel 2 Output Mask
0
1
1
CH1OM
Channel output is not masked. It continues to operate normally.
Channel output is masked. It is forced to its inactive state.
Channel 3 Output Mask
0
1
2
CH2OM
Channel output is not masked. It continues to operate normally.
Channel output is masked. It is forced to its inactive state.
Channel 4 Output Mask
0
1
3
CH3OM
Channel output is not masked. It continues to operate normally.
Channel output is masked. It is forced to its inactive state.
Channel 5 Output Mask
0
1
4
CH4OM
Channel output is not masked. It continues to operate normally.
Channel output is masked. It is forced to its inactive state.
Channel output is not masked. It continues to operate normally.
Channel output is masked. It is forced to its inactive state.
Channel 0 Output Mask
Defines if the channel output is masked or unmasked.
0
1
Channel output is not masked. It continues to operate normally.
Channel output is masked. It is forced to its inactive state.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
395
Memory map and register definition
26.3.14 Function For Linked Channels (FTMx_COMBINE)
This register contains the control bits used to configure the fault control, synchronization,
deadtime insertion, Dual Edge Capture mode, Complementary, and Combine mode for
each pair of channels (n) and (n+1), where n equals 0, 2, 4, and 6.
21
20
19
18
17
16
0
FAULTEN2
SYNCEN2
DTEN2
DECAP2
DECAPEN2
COMP2
COMBINE2
0
0
0
0
0
0
0
0
0
0
8
7
6
5
4
3
2
1
0
0
SYNCEN0
DTEN0
DECAP0
DECAPEN0
COMP0
COMBINE0
0
Bit
15
14
13
12
11
10
9
R
0
DECAPEN1
0
22
FAULTEN0
0
DECAP1
0
23
COMBINE3
0
DTEN1
0
24
COMBINE1
SYNCEN3
Reset
SYNCEN1
26
COMP3
FAULTEN3
28
COMP1
0
0
0
0
0
0
0
Reset
27
DECAPEN3
R
W
29
DECAP3
31
W
30
DTEN3
Bit
FAULTEN1
Address: Base address + 64h offset
25
0
0
0
0
0
0
0
0
0
0
FTMx_COMBINE field descriptions
Field
31
Reserved
30
FAULTEN3
Description
This field is reserved.
This read-only field is reserved and always has the value 0.
Fault Control Enable For n = 6
Enables the fault control in channels (n) and (n+1).
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0
1
29
SYNCEN3
Synchronization Enable For n = 6
Enables PWM synchronization of registers C(n)V and C(n+1)V.
0
1
28
DTEN3
The fault control in this pair of channels is disabled.
The fault control in this pair of channels is enabled.
The PWM synchronization in this pair of channels is disabled.
The PWM synchronization in this pair of channels is enabled.
Deadtime Enable For n = 6
Enables the deadtime insertion in the channels (n) and (n+1).
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0
1
The deadtime insertion in this pair of channels is disabled.
The deadtime insertion in this pair of channels is enabled.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
396
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
FTMx_COMBINE field descriptions (continued)
Field
27
DECAP3
Description
Dual Edge Capture Mode Captures For n = 6
Enables the capture of the FTM counter value according to the channel (n) input event and the
configuration of the dual edge capture bits.
This field applies only when FTMEN = 1 and DECAPEN = 1.
DECAP bit is cleared automatically by hardware if dual edge capture – one-shot mode is selected and
when the capture of channel (n+1) event is made.
0
1
26
DECAPEN3
The dual edge captures are inactive.
The dual edge captures are active.
Dual Edge Capture Mode Enable For n = 6
Enables the Dual Edge Capture mode in the channels (n) and (n+1). This bit reconfigures the function of
MSnA, ELSnB:ELSnA and ELS(n+1)B:ELS(n+1)A bits in Dual Edge Capture mode according to Table
26-7.
This field applies only when FTMEN = 1.
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0
1
25
COMP3
The Dual Edge Capture mode in this pair of channels is disabled.
The Dual Edge Capture mode in this pair of channels is enabled.
Complement Of Channel (n) for n = 6
Enables Complementary mode for the combined channels. In Complementary mode the channel (n+1)
output is the inverse of the channel (n) output.
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0
1
24
COMBINE3
The channel (n+1) output is the same as the channel (n) output.
The channel (n+1) output is the complement of the channel (n) output.
Combine Channels For n = 6
Enables the combine feature for channels (n) and (n+1).
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0
1
23
Reserved
22
FAULTEN2
Channels (n) and (n+1) are independent.
Channels (n) and (n+1) are combined.
This field is reserved.
This read-only field is reserved and always has the value 0.
Fault Control Enable For n = 4
Enables the fault control in channels (n) and (n+1).
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0
1
21
SYNCEN2
The fault control in this pair of channels is disabled.
The fault control in this pair of channels is enabled.
Synchronization Enable For n = 4
Enables PWM synchronization of registers C(n)V and C(n+1)V.
0
1
The PWM synchronization in this pair of channels is disabled.
The PWM synchronization in this pair of channels is enabled.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
397
Memory map and register definition
FTMx_COMBINE field descriptions (continued)
Field
20
DTEN2
Description
Deadtime Enable For n = 4
Enables the deadtime insertion in the channels (n) and (n+1).
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0
1
19
DECAP2
The deadtime insertion in this pair of channels is disabled.
The deadtime insertion in this pair of channels is enabled.
Dual Edge Capture Mode Captures For n = 4
Enables the capture of the FTM counter value according to the channel (n) input event and the
configuration of the dual edge capture bits.
This field applies only when FTMEN = 1 and DECAPEN = 1.
DECAP bit is cleared automatically by hardware if dual edge capture – one-shot mode is selected and
when the capture of channel (n+1) event is made.
0
1
18
DECAPEN2
The dual edge captures are inactive.
The dual edge captures are active.
Dual Edge Capture Mode Enable For n = 4
Enables the Dual Edge Capture mode in the channels (n) and (n+1). This bit reconfigures the function of
MSnA, ELSnB:ELSnA and ELS(n+1)B:ELS(n+1)A bits in Dual Edge Capture mode according to Table
26-7.
This field applies only when FTMEN = 1.
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0
1
17
COMP2
The Dual Edge Capture mode in this pair of channels is disabled.
The Dual Edge Capture mode in this pair of channels is enabled.
Complement Of Channel (n) For n = 4
Enables Complementary mode for the combined channels. In Complementary mode the channel (n+1)
output is the inverse of the channel (n) output.
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0
1
16
COMBINE2
The channel (n+1) output is the same as the channel (n) output.
The channel (n+1) output is the complement of the channel (n) output.
Combine Channels For n = 4
Enables the combine feature for channels (n) and (n+1).
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0
1
15
Reserved
14
FAULTEN1
Channels (n) and (n+1) are independent.
Channels (n) and (n+1) are combined.
This field is reserved.
This read-only field is reserved and always has the value 0.
Fault Control Enable For n = 2
Enables the fault control in channels (n) and (n+1).
This field is write protected. It can be written only when MODE[WPDIS] = 1.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
398
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
FTMx_COMBINE field descriptions (continued)
Field
Description
0
1
13
SYNCEN1
Synchronization Enable For n = 2
Enables PWM synchronization of registers C(n)V and C(n+1)V.
0
1
12
DTEN1
The fault control in this pair of channels is disabled.
The fault control in this pair of channels is enabled.
The PWM synchronization in this pair of channels is disabled.
The PWM synchronization in this pair of channels is enabled.
Deadtime Enable For n = 2
Enables the deadtime insertion in the channels (n) and (n+1).
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0
1
11
DECAP1
The deadtime insertion in this pair of channels is disabled.
The deadtime insertion in this pair of channels is enabled.
Dual Edge Capture Mode Captures For n = 2
Enables the capture of the FTM counter value according to the channel (n) input event and the
configuration of the dual edge capture bits.
This field applies only when FTMEN = 1 and DECAPEN = 1.
DECAP bit is cleared automatically by hardware if Dual Edge Capture – One-Shot mode is selected and
when the capture of channel (n+1) event is made.
0
1
10
DECAPEN1
The dual edge captures are inactive.
The dual edge captures are active.
Dual Edge Capture Mode Enable For n = 2
Enables the Dual Edge Capture mode in the channels (n) and (n+1). This bit reconfigures the function of
MSnA, ELSnB:ELSnA and ELS(n+1)B:ELS(n+1)A bits in Dual Edge Capture mode according to Table
26-7.
This field applies only when FTMEN = 1.
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0
1
9
COMP1
The Dual Edge Capture mode in this pair of channels is disabled.
The Dual Edge Capture mode in this pair of channels is enabled.
Complement Of Channel (n) For n = 2
Enables Complementary mode for the combined channels. In Complementary mode the channel (n+1)
output is the inverse of the channel (n) output.
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0
1
8
COMBINE1
The channel (n+1) output is the same as the channel (n) output.
The channel (n+1) output is the complement of the channel (n) output.
Combine Channels For n = 2
Enables the combine feature for channels (n) and (n+1).
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0
1
Channels (n) and (n+1) are independent.
Channels (n) and (n+1) are combined.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
399
Memory map and register definition
FTMx_COMBINE field descriptions (continued)
Field
7
Reserved
6
FAULTEN0
Description
This field is reserved.
This read-only field is reserved and always has the value 0.
Fault Control Enable For n = 0
Enables the fault control in channels (n) and (n+1).
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0
1
5
SYNCEN0
Synchronization Enable For n = 0
Enables PWM synchronization of registers C(n)V and C(n+1)V.
0
1
4
DTEN0
The fault control in this pair of channels is disabled.
The fault control in this pair of channels is enabled.
The PWM synchronization in this pair of channels is disabled.
The PWM synchronization in this pair of channels is enabled.
Deadtime Enable For n = 0
Enables the deadtime insertion in the channels (n) and (n+1).
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0
1
3
DECAP0
The deadtime insertion in this pair of channels is disabled.
The deadtime insertion in this pair of channels is enabled.
Dual Edge Capture Mode Captures For n = 0
Enables the capture of the FTM counter value according to the channel (n) input event and the
configuration of the dual edge capture bits.
This field applies only when FTMEN = 1 and DECAPEN = 1.
DECAP bit is cleared automatically by hardware if dual edge capture – one-shot mode is selected and
when the capture of channel (n+1) event is made.
0
1
2
DECAPEN0
The dual edge captures are inactive.
The dual edge captures are active.
Dual Edge Capture Mode Enable For n = 0
Enables the Dual Edge Capture mode in the channels (n) and (n+1). This bit reconfigures the function of
MSnA, ELSnB:ELSnA and ELS(n+1)B:ELS(n+1)A bits in Dual Edge Capture mode according to Table
26-7.
This field applies only when FTMEN = 1.
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0
1
1
COMP0
The Dual Edge Capture mode in this pair of channels is disabled.
The Dual Edge Capture mode in this pair of channels is enabled.
Complement Of Channel (n) For n = 0
Enables Complementary mode for the combined channels. In Complementary mode the channel (n+1)
output is the inverse of the channel (n) output.
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0
1
The channel (n+1) output is the same as the channel (n) output.
The channel (n+1) output is the complement of the channel (n) output.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
400
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
FTMx_COMBINE field descriptions (continued)
Field
Description
0
COMBINE0
Combine Channels For n = 0
Enables the combine feature for channels (n) and (n+1).
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0
1
Channels (n) and (n+1) are independent.
Channels (n) and (n+1) are combined.
26.3.15 Deadtime Insertion Control (FTMx_DEADTIME)
This register selects the deadtime prescaler factor and deadtime value. All FTM channels
use this clock prescaler and this deadtime value for the deadtime insertion.
Address: Base address + 68h offset
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
0
R
0
0
0
0
0
0
0
0
0
0
0
0
6
5
4
DTPS
W
Reset
7
0
0
0
0
0
0
0
0
0
0
0
0
0
0
3
2
1
0
0
0
DTVAL
0
0
0
0
FTMx_DEADTIME field descriptions
Field
31–8
Reserved
7–6
DTPS
Description
This field is reserved.
This read-only field is reserved and always has the value 0.
Deadtime Prescaler Value
Selects the division factor of the system clock. This prescaled clock is used by the deadtime counter.
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0x
10
11
DTVAL
Divide the system clock by 1.
Divide the system clock by 4.
Divide the system clock by 16.
Deadtime Value
Selects the deadtime insertion value for the deadtime counter. The deadtime counter is clocked by a
scaled version of the system clock. See the description of DTPS.
Deadtime insert value = (DTPS × DTVAL).
DTVAL selects the number of deadtime counts inserted as follows:
When DTVAL is 0, no counts are inserted.
When DTVAL is 1, 1 count is inserted.
When DTVAL is 2, 2 counts are inserted.
This pattern continues up to a possible 63 counts.
This field is write protected. It can be written only when MODE[WPDIS] = 1.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
401
Memory map and register definition
26.3.16 FTM External Trigger (FTMx_EXTTRIG)
This register:
• Indicates when a channel trigger was generated
• Enables the generation of a trigger when the FTM counter is equal to its initial value
• Selects which channels are used in the generation of the channel triggers
Several channels can be selected to generate multiple triggers in one PWM period.
Channels 6 and 7 are not used to generate channel triggers.
Address: Base address + 6Ch offset
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
R
Reserved
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
CH1TRIG
CH0TRIG
CH5TRIG
CH4TRIG
CH3TRIG
CH2TRIG
0
0
0
0
0
0
0
TRIGF
Reset
INITTRIGEN
W
R
Reserved
0
W
Reset
0
0
0
0
0
0
0
0
0
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
402
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
FTMx_EXTTRIG field descriptions
Field
Description
31–8
Reserved
This field is reserved.
7
TRIGF
Channel Trigger Flag
Set by hardware when a channel trigger is generated. Clear TRIGF by reading EXTTRIG while TRIGF is
set and then writing a 0 to TRIGF. Writing a 1 to TRIGF has no effect.
If another channel trigger is generated before the clearing sequence is completed, the sequence is reset
so TRIGF remains set after the clear sequence is completed for the earlier TRIGF.
0
1
6
INITTRIGEN
Initialization Trigger Enable
Enables the generation of the trigger when the FTM counter is equal to the CNTIN register.
0
1
5
CH1TRIG
Enables the generation of the channel trigger when the FTM counter is equal to the CnV register.
Enables the generation of the channel trigger when the FTM counter is equal to the CnV register.
Enables the generation of the channel trigger when the FTM counter is equal to the CnV register.
Enables the generation of the channel trigger when the FTM counter is equal to the CnV register.
The generation of the channel trigger is disabled.
The generation of the channel trigger is enabled.
Channel 3 Trigger Enable
Enables the generation of the channel trigger when the FTM counter is equal to the CnV register.
0
1
0
CH2TRIG
The generation of the channel trigger is disabled.
The generation of the channel trigger is enabled.
Channel 4 Trigger Enable
0
1
1
CH3TRIG
The generation of the channel trigger is disabled.
The generation of the channel trigger is enabled.
Channel 5 Trigger Enable
0
1
2
CH4TRIG
The generation of the channel trigger is disabled.
The generation of the channel trigger is enabled.
Channel 0 Trigger Enable
0
1
3
CH5TRIG
The generation of initialization trigger is disabled.
The generation of initialization trigger is enabled.
Channel 1 Trigger Enable
0
1
4
CH0TRIG
No channel trigger was generated.
A channel trigger was generated.
The generation of the channel trigger is disabled.
The generation of the channel trigger is enabled.
Channel 2 Trigger Enable
Enables the generation of the channel trigger when the FTM counter is equal to the CnV register.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
403
Memory map and register definition
FTMx_EXTTRIG field descriptions (continued)
Field
Description
0
1
The generation of the channel trigger is disabled.
The generation of the channel trigger is enabled.
26.3.17 Channels Polarity (FTMx_POL)
This register defines the output polarity of the FTM channels.
NOTE
The safe value that is driven in a channel output when the fault
control is enabled and a fault condition is detected is the
inactive state of the channel. That is, the safe value of a channel
is the value of its POL bit.
Address: Base address + 70h offset
Bit
R
W
31
30
29
28
27
26
25
24
Reset
0
0
0
0
0
0
0
0
Bit
R
W
15
14
13
12
11
10
9
8
Reset
0
23
22
21
20
19
18
17
16
0
0
0
0
0
0
0
0
7
6
5
4
3
2
1
0
Reserved
Reserved
0
0
0
0
POL7 POL6 POL5 POL4 POL3 POL2 POL1 POL0
0
0
0
0
0
0
0
0
0
0
0
FTMx_POL field descriptions
Field
31–8
Reserved
7
POL7
Description
This field is reserved.
Channel 7 Polarity
Defines the polarity of the channel output.
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0
1
6
POL6
The channel polarity is active high.
The channel polarity is active low.
Channel 6 Polarity
Defines the polarity of the channel output.
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0
1
5
POL5
The channel polarity is active high.
The channel polarity is active low.
Channel 5 Polarity
Defines the polarity of the channel output.
This field is write protected. It can be written only when MODE[WPDIS] = 1.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
404
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
FTMx_POL field descriptions (continued)
Field
Description
0
1
4
POL4
The channel polarity is active high.
The channel polarity is active low.
Channel 4 Polarity
Defines the polarity of the channel output.
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0
1
3
POL3
The channel polarity is active high.
The channel polarity is active low.
Channel 3 Polarity
Defines the polarity of the channel output.
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0
1
2
POL2
The channel polarity is active high.
The channel polarity is active low.
Channel 2 Polarity
Defines the polarity of the channel output.
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0
1
1
POL1
The channel polarity is active high.
The channel polarity is active low.
Channel 1 Polarity
Defines the polarity of the channel output.
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0
1
0
POL0
The channel polarity is active high.
The channel polarity is active low.
Channel 0 Polarity
Defines the polarity of the channel output.
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0
1
The channel polarity is active high.
The channel polarity is active low.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
405
Memory map and register definition
26.3.18 Fault Mode Status (FTMx_FMS)
This register contains the fault detection flags, write protection enable bit, and the logic
OR of the enabled fault inputs.
Address: Base address + 74h offset
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
0
R
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
0
0
R
0
W
Reset
0
0
0
0
0
0
0
0
0
0
0
0
FAULTF0
0
FAULTF1
0
FAULTF2
0
FAULTF3
0
WPEN
0
FAULTF
Reset
FAULTIN
W
0
0
0
0
0
0
0
0
FTMx_FMS field descriptions
Field
Description
31–8
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
7
FAULTF
Fault Detection Flag
Represents the logic OR of the individual FAULTFj bits where j = 3, 2, 1, 0. Clear FAULTF by reading the
FMS register while FAULTF is set and then writing a 0 to FAULTF while there is no existing fault condition
at the enabled fault inputs. Writing a 1 to FAULTF has no effect.
If another fault condition is detected in an enabled fault input before the clearing sequence is completed,
the sequence is reset so FAULTF remains set after the clearing sequence is completed for the earlier fault
condition. FAULTF is also cleared when FAULTFj bits are cleared individually.
0
1
No fault condition was detected.
A fault condition was detected.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
406
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
FTMx_FMS field descriptions (continued)
Field
6
WPEN
Description
Write Protection Enable
The WPEN bit is the negation of the WPDIS bit. WPEN is set when 1 is written to it. WPEN is cleared
when WPEN bit is read as a 1 and then 1 is written to WPDIS. Writing 0 to WPEN has no effect.
0
1
5
FAULTIN
Write protection is disabled. Write protected bits can be written.
Write protection is enabled. Write protected bits cannot be written.
Fault Inputs
Represents the logic OR of the enabled fault inputs after their filter (if their filter is enabled) when fault
control is enabled.
0
1
The logic OR of the enabled fault inputs is 0.
The logic OR of the enabled fault inputs is 1.
4
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
3
FAULTF3
Fault Detection Flag 3
Set by hardware when fault control is enabled, the corresponding fault input is enabled and a fault
condition is detected at the fault input.
Clear FAULTF3 by reading the FMS register while FAULTF3 is set and then writing a 0 to FAULTF3 while
there is no existing fault condition at the corresponding fault input. Writing a 1 to FAULTF3 has no effect.
FAULTF3 bit is also cleared when FAULTF bit is cleared.
If another fault condition is detected at the corresponding fault input before the clearing sequence is
completed, the sequence is reset so FAULTF3 remains set after the clearing sequence is completed for
the earlier fault condition.
0
1
2
FAULTF2
No fault condition was detected at the fault input.
A fault condition was detected at the fault input.
Fault Detection Flag 2
Set by hardware when fault control is enabled, the corresponding fault input is enabled and a fault
condition is detected at the fault input.
Clear FAULTF2 by reading the FMS register while FAULTF2 is set and then writing a 0 to FAULTF2 while
there is no existing fault condition at the corresponding fault input. Writing a 1 to FAULTF2 has no effect.
FAULTF2 bit is also cleared when FAULTF bit is cleared.
If another fault condition is detected at the corresponding fault input before the clearing sequence is
completed, the sequence is reset so FAULTF2 remains set after the clearing sequence is completed for
the earlier fault condition.
0
1
1
FAULTF1
No fault condition was detected at the fault input.
A fault condition was detected at the fault input.
Fault Detection Flag 1
Set by hardware when fault control is enabled, the corresponding fault input is enabled and a fault
condition is detected at the fault input.
Clear FAULTF1 by reading the FMS register while FAULTF1 is set and then writing a 0 to FAULTF1 while
there is no existing fault condition at the corresponding fault input. Writing a 1 to FAULTF1 has no effect.
FAULTF1 bit is also cleared when FAULTF bit is cleared.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
407
Memory map and register definition
FTMx_FMS field descriptions (continued)
Field
Description
If another fault condition is detected at the corresponding fault input before the clearing sequence is
completed, the sequence is reset so FAULTF1 remains set after the clearing sequence is completed for
the earlier fault condition.
0
1
0
FAULTF0
No fault condition was detected at the fault input.
A fault condition was detected at the fault input.
Fault Detection Flag 0
Set by hardware when fault control is enabled, the corresponding fault input is enabled and a fault
condition is detected at the fault input.
Clear FAULTF0 by reading the FMS register while FAULTF0 is set and then writing a 0 to FAULTF0 while
there is no existing fault condition at the corresponding fault input. Writing a 1 to FAULTF0 has no effect.
FAULTF0 bit is also cleared when FAULTF bit is cleared.
If another fault condition is detected at the corresponding fault input before the clearing sequence is
completed, the sequence is reset so FAULTF0 remains set after the clearing sequence is completed for
the earlier fault condition.
0
1
No fault condition was detected at the fault input.
A fault condition was detected at the fault input.
26.3.19 Input Capture Filter Control (FTMx_FILTER)
This register selects the filter value for the inputs of channels.
Channels 4, 5, 6 and 7 do not have an input filter.
NOTE
Writing to the FILTER register has immediate effect and must
be done only when the channels 0, 1, 2, and 3 are not in input
modes. Failure to do this could result in a missing valid signal.
Address: Base address + 78h offset
Bit
R
W
31
Reset
0
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
Reserved
0
0
0
0
0
0
0
0
14
13
12
11
CH3FVAL
0
0
0
0
0
0
0
0
0
0
10
9
8
7
CH2FVAL
0
0
0
0
6
5
4
3
CH1FVAL
0
0
0
0
2
1
0
CH0FVAL
0
0
0
0
0
FTMx_FILTER field descriptions
Field
Description
31–16
Reserved
This field is reserved.
15–12
CH3FVAL
Channel 3 Input Filter
Selects the filter value for the channel input.
The filter is disabled when the value is zero.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
408
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
FTMx_FILTER field descriptions (continued)
Field
Description
11–8
CH2FVAL
Channel 2 Input Filter
Selects the filter value for the channel input.
The filter is disabled when the value is zero.
7–4
CH1FVAL
Channel 1 Input Filter
Selects the filter value for the channel input.
The filter is disabled when the value is zero.
CH0FVAL
Channel 0 Input Filter
Selects the filter value for the channel input.
The filter is disabled when the value is zero.
26.3.20 Fault Control (FTMx_FLTCTRL)
This register selects the filter value for the fault inputs, enables the fault inputs and the
fault inputs filter.
Address: Base address + 7Ch offset
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
0
R
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
FFLTR3EN
FFLTR2EN
FFLTR1EN
FFLTR0EN
FAULT3EN
FAULT2EN
FAULT1EN
FAULT0EN
W
0
0
0
0
0
0
0
0
0
R
FFVAL
W
Reset
0
0
0
0
0
0
0
0
FTMx_FLTCTRL field descriptions
Field
31–12
Reserved
11–8
FFVAL
Description
This field is reserved.
This read-only field is reserved and always has the value 0.
Fault Input Filter
Selects the filter value for the fault inputs.
The fault filter is disabled when the value is zero.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
409
Memory map and register definition
FTMx_FLTCTRL field descriptions (continued)
Field
Description
NOTE: Writing to this field has immediate effect and must be done only when the fault control or all fault
inputs are disabled. Failure to do this could result in a missing fault detection.
7
FFLTR3EN
Fault Input 3 Filter Enable
Enables the filter for the fault input.
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0
1
6
FFLTR2EN
Fault input filter is disabled.
Fault input filter is enabled.
Fault Input 2 Filter Enable
Enables the filter for the fault input.
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0
1
5
FFLTR1EN
Fault input filter is disabled.
Fault input filter is enabled.
Fault Input 1 Filter Enable
Enables the filter for the fault input.
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0
1
4
FFLTR0EN
Fault input filter is disabled.
Fault input filter is enabled.
Fault Input 0 Filter Enable
Enables the filter for the fault input.
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0
1
3
FAULT3EN
Fault input filter is disabled.
Fault input filter is enabled.
Fault Input 3 Enable
Enables the fault input.
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0
1
2
FAULT2EN
Fault input is disabled.
Fault input is enabled.
Fault Input 2 Enable
Enables the fault input.
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0
1
1
FAULT1EN
Fault input is disabled.
Fault input is enabled.
Fault Input 1 Enable
Enables the fault input.
This field is write protected. It can be written only when MODE[WPDIS] = 1.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
410
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
FTMx_FLTCTRL field descriptions (continued)
Field
Description
0
1
0
FAULT0EN
Fault input is disabled.
Fault input is enabled.
Fault Input 0 Enable
Enables the fault input.
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0
1
Fault input is disabled.
Fault input is enabled.
26.3.21 Configuration (FTMx_CONF)
This register selects the number of times that the FTM counter overflow should occur
before the TOF bit to be set, the FTM behavior in Debug modes, the use of an external
global time base, and the global time base signal generation.
Address: Base address + 84h offset
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
0
R
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
GTBEOUT
GTBEEN
W
0
0
0
0
0
0
0
R
W
Reset
0
0
0
0
0
0
BDMMODE
0
0
NUMTOF
0
0
0
0
FTMx_CONF field descriptions
Field
Description
31–11
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
10
GTBEOUT
Global Time Base Output
Enables the global time base signal generation to other FTMs.
0
1
A global time base signal generation is disabled.
A global time base signal generation is enabled.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
411
Memory map and register definition
FTMx_CONF field descriptions (continued)
Field
Description
9
GTBEEN
Global Time Base Enable
Configures the FTM to use an external global time base signal that is generated by another FTM.
0
1
8
Reserved
Use of an external global time base is disabled.
Use of an external global time base is enabled.
This field is reserved.
This read-only field is reserved and always has the value 0.
7–6
BDMMODE
Debug Mode
Selects the FTM behavior in Debug mode. See Debug mode.
5
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
NUMTOF
TOF Frequency
Selects the ratio between the number of counter overflows to the number of times the TOF bit is set.
NUMTOF = 0: The TOF bit is set for each counter overflow.
NUMTOF = 1: The TOF bit is set for the first counter overflow but not for the next overflow.
NUMTOF = 2: The TOF bit is set for the first counter overflow but not for the next 2 overflows.
NUMTOF = 3: The TOF bit is set for the first counter overflow but not for the next 3 overflows.
This pattern continues up to a maximum of 31.
26.3.22 FTM Fault Input Polarity (FTMx_FLTPOL)
This register defines the fault inputs polarity.
Address: Base address + 88h offset
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
0
R
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
FLT3POL
FLT2POL
FLT1POL
FLT0POL
W
0
0
0
0
0
0
0
0
0
0
0
R
W
Reset
0
0
0
0
0
0
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
412
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
FTMx_FLTPOL field descriptions
Field
Description
31–4
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
3
FLT3POL
Fault Input 3 Polarity
Defines the polarity of the fault input.
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0
1
2
FLT2POL
The fault input polarity is active high. A 1 at the fault input indicates a fault.
The fault input polarity is active low. A 0 at the fault input indicates a fault.
Fault Input 2 Polarity
Defines the polarity of the fault input.
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0
1
1
FLT1POL
The fault input polarity is active high. A 1 at the fault input indicates a fault.
The fault input polarity is active low. A 0 at the fault input indicates a fault.
Fault Input 1 Polarity
Defines the polarity of the fault input.
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0
1
0
FLT0POL
The fault input polarity is active high. A 1 at the fault input indicates a fault.
The fault input polarity is active low. A 0 at the fault input indicates a fault.
Fault Input 0 Polarity
Defines the polarity of the fault input.
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0
1
The fault input polarity is active high. A 1 at the fault input indicates a fault.
The fault input polarity is active low. A 0 at the fault input indicates a fault.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
413
Memory map and register definition
26.3.23 Synchronization Configuration (FTMx_SYNCONF)
This register selects the PWM synchronization configuration, SWOCTRL, INVCTRL
and CNTIN registers synchronization, if FTM clears the TRIGj bit, where j = 0, 1, 2,
when the hardware trigger j is detected.
Address: Base address + 8Ch offset
27
26
25
24
23
22
21
20
19
18
17
16
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
0
0
0
0
0
0
0
0
0
SWOC
0
SYNCMODE
0
SWRSTCNT
0
SWWRBUF
Reset
SWOM
W
SWINVC
0
R
SWSOC
W
INVC
0
0
0
0
0
0
HWTRIGMOD
E
Reset
0
R
CNTINC
HWRSTCNT
28
HWWRBUF
29
HWOM
30
HWINVC
31
HWSOC
Bit
0
FTMx_SYNCONF field descriptions
Field
Description
31–21
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
20
HWSOC
Software output control synchronization is activated by a hardware trigger.
19
HWINVC
Inverting control synchronization is activated by a hardware trigger.
18
HWOM
0
1
0
1
A hardware trigger does not activate the SWOCTRL register synchronization.
A hardware trigger activates the SWOCTRL register synchronization.
A hardware trigger does not activate the INVCTRL register synchronization.
A hardware trigger activates the INVCTRL register synchronization.
Output mask synchronization is activated by a hardware trigger.
0
1
A hardware trigger does not activate the OUTMASK register synchronization.
A hardware trigger activates the OUTMASK register synchronization.
17
HWWRBUF
MOD, CNTIN, and CV registers synchronization is activated by a hardware trigger.
16
HWRSTCNT
FTM counter synchronization is activated by a hardware trigger.
0
1
0
1
A hardware trigger does not activate MOD, CNTIN, and CV registers synchronization.
A hardware trigger activates MOD, CNTIN, and CV registers synchronization.
A hardware trigger does not activate the FTM counter synchronization.
A hardware trigger activates the FTM counter synchronization.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
414
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
FTMx_SYNCONF field descriptions (continued)
Field
Description
15–13
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
12
SWSOC
Software output control synchronization is activated by the software trigger.
11
SWINVC
Inverting control synchronization is activated by the software trigger.
10
SWOM
0
1
0
1
The software trigger does not activate the SWOCTRL register synchronization.
The software trigger activates the SWOCTRL register synchronization.
The software trigger does not activate the INVCTRL register synchronization.
The software trigger activates the INVCTRL register synchronization.
Output mask synchronization is activated by the software trigger.
0
1
The software trigger does not activate the OUTMASK register synchronization.
The software trigger activates the OUTMASK register synchronization.
9
SWWRBUF
MOD, CNTIN, and CV registers synchronization is activated by the software trigger.
8
SWRSTCNT
FTM counter synchronization is activated by the software trigger.
7
SYNCMODE
Synchronization Mode
0
1
0
1
5
SWOC
4
INVC
The software trigger does not activate the FTM counter synchronization.
The software trigger activates the FTM counter synchronization.
Selects the PWM Synchronization mode.
0
1
6
Reserved
The software trigger does not activate MOD, CNTIN, and CV registers synchronization.
The software trigger activates MOD, CNTIN, and CV registers synchronization.
Legacy PWM synchronization is selected.
Enhanced PWM synchronization is selected.
This field is reserved.
This read-only field is reserved and always has the value 0.
SWOCTRL Register Synchronization
0
1
SWOCTRL register is updated with its buffer value at all rising edges of system clock.
SWOCTRL register is updated with its buffer value by the PWM synchronization.
INVCTRL Register Synchronization
0
1
INVCTRL register is updated with its buffer value at all rising edges of system clock.
INVCTRL register is updated with its buffer value by the PWM synchronization.
3
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
2
CNTINC
CNTIN Register Synchronization
1
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
0
1
CNTIN register is updated with its buffer value at all rising edges of system clock.
CNTIN register is updated with its buffer value by the PWM synchronization.
0
Hardware Trigger Mode
HWTRIGMODE
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
415
Memory map and register definition
FTMx_SYNCONF field descriptions (continued)
Field
Description
0
1
FTM clears the TRIGj bit when the hardware trigger j is detected, where j = 0, 1,2.
FTM does not clear the TRIGj bit when the hardware trigger j is detected, where j = 0, 1,2.
26.3.24 FTM Inverting Control (FTMx_INVCTRL)
This register controls when the channel (n) output becomes the channel (n+1) output, and
channel (n+1) output becomes the channel (n) output. Each INVmEN bit enables the
inverting operation for the corresponding pair channels m.
This register has a write buffer. The INVmEN bit is updated by the INVCTRL register
synchronization.
Address: Base address + 90h offset
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
0
R
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
INV3EN
INV2EN
INV1EN
INV0EN
W
0
0
0
0
0
0
0
0
0
0
0
R
W
Reset
0
0
0
0
0
0
FTMx_INVCTRL field descriptions
Field
31–4
Reserved
Description
This field is reserved.
This read-only field is reserved and always has the value 0.
3
INV3EN
Pair Channels 3 Inverting Enable
2
INV2EN
Pair Channels 2 Inverting Enable
1
INV1EN
Pair Channels 1 Inverting Enable
0
1
0
1
0
1
Inverting is disabled.
Inverting is enabled.
Inverting is disabled.
Inverting is enabled.
Inverting is disabled.
Inverting is enabled.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
416
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
FTMx_INVCTRL field descriptions (continued)
Field
Description
0
INV0EN
Pair Channels 0 Inverting Enable
0
1
Inverting is disabled.
Inverting is enabled.
26.3.25 FTM Software Output Control (FTMx_SWOCTRL)
This register enables software control of channel (n) output and defines the value forced
to the channel (n) output:
• The CHnOC bits enable the control of the corresponding channel (n) output by
software.
• The CHnOCV bits select the value that is forced at the corresponding channel (n)
output.
This register has a write buffer. The fields are updated by the SWOCTRL register
synchronization.
Address: Base address + 94h offset
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
0
R
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
R
W
CH7OCV
CH6OCV
CH5OCV
CH4OCV
CH3OCV
CH2OCV
CH1OCV
CH0OCV
CH7OC
CH6OC
CH5OC
CH4OC
CH3OC
CH2OC
CH1OC
CH0OC
W
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
FTMx_SWOCTRL field descriptions
Field
Description
31–16
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
15
CH7OCV
Channel 7 Software Output Control Value
14
CH6OCV
Channel 6 Software Output Control Value
0
1
The software output control forces 0 to the channel output.
The software output control forces 1 to the channel output.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
417
Memory map and register definition
FTMx_SWOCTRL field descriptions (continued)
Field
Description
0
1
The software output control forces 0 to the channel output.
The software output control forces 1 to the channel output.
13
CH5OCV
Channel 5 Software Output Control Value
12
CH4OCV
Channel 4 Software Output Control Value
11
CH3OCV
Channel 3 Software Output Control Value
10
CH2OCV
Channel 2 Software Output Control Value
9
CH1OCV
Channel 1 Software Output Control Value
8
CH0OCV
Channel 0 Software Output Control Value
7
CH7OC
Channel 7 Software Output Control Enable
6
CH6OC
Channel 6 Software Output Control Enable
5
CH5OC
Channel 5 Software Output Control Enable
4
CH4OC
Channel 4 Software Output Control Enable
3
CH3OC
Channel 3 Software Output Control Enable
2
CH2OC
Channel 2 Software Output Control Enable
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
The software output control forces 0 to the channel output.
The software output control forces 1 to the channel output.
The software output control forces 0 to the channel output.
The software output control forces 1 to the channel output.
The software output control forces 0 to the channel output.
The software output control forces 1 to the channel output.
The software output control forces 0 to the channel output.
The software output control forces 1 to the channel output.
The software output control forces 0 to the channel output.
The software output control forces 1 to the channel output.
The software output control forces 0 to the channel output.
The software output control forces 1 to the channel output.
The channel output is not affected by software output control.
The channel output is affected by software output control.
The channel output is not affected by software output control.
The channel output is affected by software output control.
The channel output is not affected by software output control.
The channel output is affected by software output control.
The channel output is not affected by software output control.
The channel output is affected by software output control.
The channel output is not affected by software output control.
The channel output is affected by software output control.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
418
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
FTMx_SWOCTRL field descriptions (continued)
Field
Description
0
1
The channel output is not affected by software output control.
The channel output is affected by software output control.
1
CH1OC
Channel 1 Software Output Control Enable
0
CH0OC
Channel 0 Software Output Control Enable
0
1
0
1
The channel output is not affected by software output control.
The channel output is affected by software output control.
The channel output is not affected by software output control.
The channel output is affected by software output control.
26.3.26 FTM PWM Load (FTMx_PWMLOAD)
Enables the loading of the MOD, CNTIN, C(n)V, and C(n+1)V registers with the values
of their write buffers when the FTM counter changes from the MOD register value to its
next value or when a channel (j) match occurs. A match occurs for the channel (j) when
FTM counter = C(j)V.
Address: Base address + 98h offset
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
0
R
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
0
CH7SEL
CH6SEL
CH5SEL
CH4SEL
CH3SEL
CH2SEL
CH1SEL
CH0SEL
W
0
0
0
0
0
0
0
0
0
LDOK
0
R
W
Reset
0
0
0
0
0
0
0
FTMx_PWMLOAD field descriptions
Field
31–10
Reserved
9
LDOK
Description
This field is reserved.
This read-only field is reserved and always has the value 0.
Load Enable
Enables the loading of the MOD, CNTIN, and CV registers with the values of their write buffers.
0
1
Loading updated values is disabled.
Loading updated values is enabled.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
419
Functional description
FTMx_PWMLOAD field descriptions (continued)
Field
Description
8
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
7
CH7SEL
Channel 7 Select
6
CH6SEL
Channel 6 Select
5
CH5SEL
Channel 5 Select
4
CH4SEL
Channel 4 Select
3
CH3SEL
Channel 3 Select
2
CH2SEL
Channel 2 Select
1
CH1SEL
Channel 1 Select
0
CH0SEL
Channel 0 Select
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Do not include the channel in the matching process.
Include the channel in the matching process.
Do not include the channel in the matching process.
Include the channel in the matching process.
Do not include the channel in the matching process.
Include the channel in the matching process.
Do not include the channel in the matching process.
Include the channel in the matching process.
Do not include the channel in the matching process.
Include the channel in the matching process.
Do not include the channel in the matching process.
Include the channel in the matching process.
Do not include the channel in the matching process.
Include the channel in the matching process.
Do not include the channel in the matching process.
Include the channel in the matching process.
26.4 Functional description
The notation used in this document to represent the counters and the generation of the
signals is shown in the following figure.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
420
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
FTM counting is up.
Channel (n) is in high-true EPWM mode.
PS[2:0] = 001
CNTIN = 0x0000
MOD = 0x0004
CnV = 0x0002
prescaler counter
FTM counter
1
0
3
1
0
4
1
0
1
0
0
1
1
0
1
0
2
3
1
0
4
1
0
0
1
0
1 0
0
1
2
1
1
0
3
0
4
1
0
1
0
1
1
0
2
channel (n) output
counter
overflow
channel (n)
match
counter
overflow
channel (n)
match
counter
overflow
channel (n)
match
Figure 26-162. Notation used
26.4.1 Clock source
The FTM has only one clock domain: the system clock.
26.4.1.1 Counter clock source
The CLKS[1:0] bits in the SC register select one of three possible clock sources for the
FTM counter or disable the FTM counter. After any MCU reset, CLKS[1:0] = 0:0 so no
clock source is selected.
The CLKS[1:0] bits may be read or written at any time. Disabling the FTM counter by
writing 0:0 to the CLKS[1:0] bits does not affect the FTM counter value or other
registers.
The fixed frequency clock is an alternative clock source for the FTM counter that allows
the selection of a clock other than the system clock or an external clock. This clock input
is defined by chip integration. Refer to the chip specific documentation for further
information. Due to FTM hardware implementation limitations, the frequency of the
fixed frequency clock must not exceed 1/2 of the system clock frequency.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
421
Functional description
The external clock passes through a synchronizer clocked by the system clock to assure
that counter transitions are properly aligned to system clock transitions.Therefore, to
meet Nyquist criteria considering also jitter, the frequency of the external clock source
must not exceed 1/4 of the system clock frequency.
26.4.2 Prescaler
The selected counter clock source passes through a prescaler that is a 7-bit counter. The
value of the prescaler is selected by the PS[2:0] bits. The following figure shows an
example of the prescaler counter and FTM counter.
FTM counting is up.
PS[2:0] = 001
CNTIN = 0x0000
MOD = 0x0003
selected input clock
prescaler counter
1
FTM counter
0
0
1
1
0
1
2
0
1
0
3
1
0
0
1
1
0
1
2
0
1
3
0
1
0
0
1
Figure 26-163. Example of the prescaler counter
26.4.3 Counter
The FTM has a 16-bit counter that is used by the channels either for input or output
modes. The FTM counter clock is the selected clock divided by the prescaler.
The FTM counter has these modes of operation:
• Up counting
• Up-down counting
26.4.3.1 Up counting
Up counting is selected when:
• CPWMS = 0
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
422
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
CNTIN defines the starting value of the count and MOD defines the final value of the
count, see the following figure. The value of CNTIN is loaded into the FTM counter, and
the counter increments until the value of MOD is reached, at which point the counter is
reloaded with the value of CNTIN.
The FTM period when using up counting is (MOD – CNTIN + 0x0001) × period of the
FTM counter clock.
The TOF bit is set when the FTM counter changes from MOD to CNTIN.
FTM counting is up.
CNTIN = 0xFFFC (in two's complement is equal to -4)
MOD = 0x0004
FTM counter (in decimal values)
4
-4 -3 -2 -1 0
1
2
3
4
-4 -3 -2 -1
0
1
2
3
4
-4 -3
TOF bit
set TOF bit
set TOF bit
set TOF bit
period of FTM counter clock
period of counting = (MOD - CNTIN + 0x0001) x period of FTM counter clock
Figure 26-164. Example of FTM up and signed counting
Table 26-238. FTM counting based on CNTIN value
When
Then
CNTIN = 0x0000
The FTM counting is equivalent to TPM up counting, that is,
up and unsigned counting. See the following figure.
CNTIN[15] = 1
The initial value of the FTM counter is a negative number in
two's complement, so the FTM counting is up and signed.
CNTIN[15] = 0 and CNTIN ≠ 0x0000
The initial value of the FTM counter is a positive number, so
the FTM counting is up and unsigned.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
423
Functional description
FTM counting is up
CNTIN = 0x0000
MOD = 0x0004
FTM counter
3
4
0
1
2
3
4
0
1
2
3
0
4
1
2
TOF bit
set TOF bit
set TOF bit
set TOF bit
period of FTM counter clock
period of counting = (MOD - CNTIN + 0x0001) x period of FTM counter clock
= (MOD + 0x0001) x period of FTM counter clock
Figure 26-165. Example of FTM up counting with CNTIN = 0x0000
Note
• FTM operation is only valid when the value of the CNTIN
register is less than the value of the MOD register, either in
the unsigned counting or signed counting. It is the
responsibility of the software to ensure that the values in
the CNTIN and MOD registers meet this requirement. Any
values of CNTIN and MOD that do not satisfy this criteria
can result in unpredictable behavior.
• MOD = CNTIN is a redundant condition. In this case, the
FTM counter is always equal to MOD and the TOF bit is
set in each rising edge of the FTM counter clock.
• When MOD = 0x0000, CNTIN = 0x0000, for example
after reset, and FTMEN = 1, the FTM counter remains
stopped at 0x0000 until a non-zero value is written into the
MOD or CNTIN registers.
• Setting CNTIN to be greater than the value of MOD is not
recommended as this unusual setting may make the FTM
operation difficult to comprehend. However, there is no
restriction on this configuration, and an example is shown
in the following figure.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
424
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
FTM counting is up
MOD = 0x0005
CNTIN = 0x0015
load of CNTIN
FTM counter
load of CNTIN
0x0005 0x0015 0x0016 ... 0xFFFE 0xFFFF 0x0000 0x0001 0x0002 0x0003 0x0004 0x0005 0x0015 0x0016 ...
...
TOF bit
set TOF bit
set TOF bit
Figure 26-166. Example of up counting when the value of CNTIN is greater than the
value of MOD
26.4.3.2 Up-down counting
Up-down counting is selected when:
• CPWMS = 1
CNTIN defines the starting value of the count and MOD defines the final value of the
count. The value of CNTIN is loaded into the FTM counter, and the counter increments
until the value of MOD is reached, at which point the counter is decremented until it
returns to the value of CNTIN and the up-down counting restarts.
The FTM period when using up-down counting is 2 × (MOD – CNTIN) × period of the
FTM counter clock.
The TOF bit is set when the FTM counter changes from MOD to (MOD – 1).
If (CNTIN = 0x0000), the FTM counting is equivalent to TPM up-down counting, that is,
up-down and unsigned counting. See the following figure.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
425
Functional description
FTM counting is up-down
CNTIN = 0x0000
MOD = 0x0004
FTM counter
0
1
2
3
4
3
2
1
0
1
2
3
4
3
2
1
0
1
2
3
4
TOF bit
set TOF bit
period of FTM counter clock
set TOF bit
period of counting = 2 x (MOD - CNTIN) x period of FTM counter clock
= 2 x MOD x period of FTM counter clock
Figure 26-167. Example of up-down counting when CNTIN = 0x0000
Note
It is expected that the up-down counting be used only with
CNTIN = 0x0000.
26.4.3.3 Free running counter
If (FTMEN = 0) and (MOD = 0x0000 or MOD = 0xFFFF), the FTM counter is a free
running counter. In this case, the FTM counter runs free from 0x0000 through 0xFFFF
and the TOF bit is set when the FTM counter changes from 0xFFFF to 0x0000. See the
following figure.
FTMEN = 0
MOD = 0x0000
FTM counter
... 0x0003 0x0004 ... 0xFFFE 0xFFFF 0x0000 0x0001 0x0002 0x0003 0x0004 0x0005 0x0006 ...
TOF bit
set TOF bit
Figure 26-168. Example when the FTM counter is free running
The FTM counter is also a free running counter when:
•
•
•
•
FTMEN = 1
CPWMS = 0
CNTIN = 0x0000, and
MOD = 0xFFFF
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
426
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
26.4.3.4 Counter reset
Any one of the following cases resets the FTM counter to the value in the CNTIN register
and the channels output to its initial value, except for channels in Output Compare mode.
• Any write to CNT.
• FTM counter synchronization.
26.4.3.5 When the TOF bit is set
The NUMTOF[4:0] bits define the number of times that the FTM counter overflow
should occur before the TOF bit to be set. If NUMTOF[4:0] = 0x00, then the TOF bit is
set at each FTM counter overflow.
Initialize the FTM counter, by writing to CNT, after writing to the NUMTOF[4:0] bits to
avoid confusion about when the first counter overflow will occur.
FTM counter
NUMTOF[4:0]
TOF counter
0x02
0x01
0x02
0x00
0x01
0x02
0x00
0x01
0x02
set TOF bit
Figure 26-169. Periodic TOF when NUMTOF = 0x02
FTM counter
NUMTOF[4:0]
0x00
TOF counter
0x00
set TOF bit
Figure 26-170. Periodic TOF when NUMTOF = 0x00
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
427
Functional description
26.4.4 Input Capture mode
The Input Capture mode is selected when:
•
•
•
•
•
DECAPEN = 0
COMBINE = 0
CPWMS = 0
MSnB:MSnA = 0:0, and
ELSnB:ELSnA ≠ 0:0
When a selected edge occurs on the channel input, the current value of the FTM counter
is captured into the CnV register, at the same time the CHnF bit is set and the channel
interrupt is generated if enabled by CHnIE = 1. See the following figure.
When a channel is configured for input capture, the FTMxCHn pin is an edge-sensitive
input. ELSnB:ELSnA control bits determine which edge, falling or rising, triggers inputcapture event. Note that the maximum frequency for the channel input signal to be
detected correctly is system clock divided by 4, which is required to meet Nyquist criteria
for signal sampling.
Writes to the CnV register is ignored in Input Capture mode.
While in Debug mode, the input capture function works as configured. When a selected
edge event occurs, the FTM counter value, which is frozen because of Debug, is captured
into the CnV register and the CHnF bit is set.
was rising
edge selected?
is filter
enabled?
0
synchronizer
channel (n) input
system clock
DQ
CLK
0
rising edge
0
CHnF
1
edge
detector
DQ
CLK
Filter*
1
channel (n) interrupt
CHnIE
CnV
falling edge
0
1
0
was falling
edge selected?
FTM counter
* Filtering function is only available in the inputs of channel 0, 1, 2, and 3
Figure 26-171. Input Capture mode
If the channel input does not have a filter enabled, then the input signal is always delayed
3 rising edges of the system clock, that is, two rising edges to the synchronizer plus one
more rising edge to the edge detector. In other words, the CHnF bit is set on the third
rising edge of the system clock after a valid edge occurs on the channel input.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
428
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
Note
The Input Capture mode must be used only with CNTIN =
0x0000.
26.4.4.1 Filter for Input Capture mode
The filter function is only available on channels 0, 1, 2, and 3.
First, the input signal is synchronized by the system clock. Following synchronization,
the input signal enters the filter block. See the following figure.
CHnFVAL[3:0]
Logic to control
the filter counter
channel (n) input after
the synchronizer
filter counter
divided by 4
Logic to define
the filter output
S
Q
filter output
C
CLK
system clock
Figure 26-172. Channel input filter
When there is a state change in the input signal, the counter is reset and starts counting
up. As long as the new state is stable on the input, the counter continues to increment.
When the counter is equal to CHnFVAL[3:0], the state change of the input signal is
validated. It is then transmitted as a pulse edge to the edge detector.
If the opposite edge appears on the input signal before it can be validated, the counter is
reset. At the next input transition, the counter starts counting again. Any pulse that is
shorter than the minimum value selected by CHnFVAL[3:0] (× 4 system clocks) is
regarded as a glitch and is not passed on to the edge detector. A timing diagram of the
input filter is shown in the following figure.
The filter function is disabled when CHnFVAL[3:0] bits are zero. In this case, the input
signal is delayed 3 rising edges of the system clock. If (CHnFVAL[3:0] ≠ 0000), then the
input signal is delayed by the minimum pulse width (CHnFVAL[3:0] × 4 system clocks)
plus a further 4 rising edges of the system clock: two rising edges to the synchronizer,
one rising edge to the filter output, plus one more to the edge detector. In other words,
CHnF is set (4 + 4 × CHnFVAL[3:0]) system clock periods after a valid edge occurs on
the channel input.
The clock for the counter in the channel input filter is the system clock divided by 4.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
429
Functional description
system clock divided by 4
channel (n) input
after the synchronizer
counter
CHnFVAL[3:0] = 0010
(binary value)
Time
filter output
Figure 26-173. Channel input filter example
26.4.5 Output Compare mode
The Output Compare mode is selected when:
•
•
•
•
DECAPEN = 0
COMBINE = 0
CPWMS = 0, and
MSnB:MSnA = 0:1
In Output Compare mode, the FTM can generate timed pulses with programmable
position, polarity, duration, and frequency. When the counter matches the value in the
CnV register of an output compare channel, the channel (n) output can be set, cleared, or
toggled.
When a channel is initially configured to Toggle mode, the previous value of the channel
output is held until the first output compare event occurs.
The CHnF bit is set and the channel (n) interrupt is generated if CHnIE = 1 at the channel
(n) match (FTM counter = CnV).
MOD = 0x0005
CnV = 0x0003
channel (n)
match
counter
overflow
CNT
...
0
1
channel (n) output
previous value
CHnF bit
previous value
2
3
channel (n)
match
counter
overflow
4
5
0
1
2
3
counter
overflow
4
5
0
1
...
TOF bit
Figure 26-174. Example of the Output Compare mode when the match toggles the
channel output
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
430
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
MOD = 0x0005
CnV = 0x0003
CNT ...
channel (n) output
CHnF bit
0
counter
overflow
channel (n)
match
counter
overflow
2
1
4
3
5
0
counter
overflow
channel (n)
match
1
2
3
4
5
0
1
...
previous value
previous value
TOF bit
Figure 26-175. Example of the Output Compare mode when the match clears the
channel output
MOD = 0x0005
CnV = 0x0003
channel (n)
match
counter
overflow
CNT
channel (n) output
CHnF bit
...
0
1
2
3
counter
overflow
4
5
0
channel (n)
match
1
2
3
counter
overflow
4
5
0
1
...
previous value
previous value
TOF bit
Figure 26-176. Example of the Output Compare mode when the match sets the channel
output
If (ELSnB:ELSnA = 0:0) when the counter reaches the value in the CnV register, the
CHnF bit is set and the channel (n) interrupt is generated if CHnIE = 1, however the
channel (n) output is not modified and controlled by FTM.
Note
The Output Compare mode must be used only with CNTIN =
0x0000.
26.4.6 Edge-Aligned PWM (EPWM) mode
The Edge-Aligned mode is selected when:
•
•
•
•
DECAPEN = 0
COMBINE = 0
CPWMS = 0, and
MSnB = 1
The EPWM period is determined by (MOD − CNTIN + 0x0001) and the pulse width
(duty cycle) is determined by (CnV − CNTIN).
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
431
Functional description
The CHnF bit is set and the channel (n) interrupt is generated if CHnIE = 1 at the channel
(n) match (FTM counter = CnV), that is, at the end of the pulse width.
This type of PWM signal is called edge-aligned because the leading edges of all PWM
signals are aligned with the beginning of the period, which is the same for all channels
within an FTM.
counter overflow
counter overflow
counter overflow
period
pulse
width
channel (n) output
channel (n) match
channel (n) match
channel (n) match
Figure 26-177. EPWM period and pulse width with ELSnB:ELSnA = 1:0
If (ELSnB:ELSnA = 0:0) when the counter reaches the value in the CnV register, the
CHnF bit is set and the channel (n) interrupt is generated if CHnIE = 1, however the
channel (n) output is not controlled by FTM.
If (ELSnB:ELSnA = 1:0), then the channel (n) output is forced high at the counter
overflow when the CNTIN register value is loaded into the FTM counter, and it is forced
low at the channel (n) match (FTM counter = CnV). See the following figure.
MOD = 0x0008
CnV = 0x0005
counter
overflow
CNT
...
0
channel (n)
match
1
2
3
4
5
counter
overflow
6
7
8
0
1
2
...
channel (n) output
CHnF bit
previous value
TOF bit
Figure 26-178. EPWM signal with ELSnB:ELSnA = 1:0
If (ELSnB:ELSnA = X:1), then the channel (n) output is forced low at the counter
overflow when the CNTIN register value is loaded into the FTM counter, and it is forced
high at the channel (n) match (FTM counter = CnV). See the following figure.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
432
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
MOD = 0x0008
CnV = 0x0005
counter
overflow
CNT
...
0
channel (n)
match
1
2
3
4
5
counter
overflow
6
7
8
0
1
2
...
channel (n) output
CHnF bit
previous value
TOF bit
Figure 26-179. EPWM signal with ELSnB:ELSnA = X:1
If (CnV = 0x0000), then the channel (n) output is a 0% duty cycle EPWM signal and
CHnF bit is not set even when there is the channel (n) match. If (CnV > MOD), then the
channel (n) output is a 100% duty cycle EPWM signal and CHnF bit is not set even when
there is the channel (n) match. Therefore, MOD must be less than 0xFFFF in order to get
a 100% duty cycle EPWM signal.
Note
The EPWM mode must be used only with CNTIN = 0x0000.
26.4.7 Center-Aligned PWM (CPWM) mode
The Center-Aligned mode is selected when:
• DECAPEN = 0
• COMBINE = 0, and
• CPWMS = 1
The CPWM pulse width (duty cycle) is determined by 2 × (CnV − CNTIN) and the
period is determined by 2 × (MOD − CNTIN). See the following figure. MOD must be
kept in the range of 0x0001 to 0x7FFF because values outside this range can produce
ambiguous results.
In the CPWM mode, the FTM counter counts up until it reaches MOD and then counts
down until it reaches CNTIN.
The CHnF bit is set and channel (n) interrupt is generated (if CHnIE = 1) at the channel
(n) match (FTM counter = CnV) when the FTM counting is down (at the begin of the
pulse width) and when the FTM counting is up (at the end of the pulse width).
This type of PWM signal is called center-aligned because the pulse width centers for all
channels are aligned with the value of CNTIN.
The other channel modes are not compatible with the up-down counter (CPWMS = 1).
Therefore, all FTM channels must be used in CPWM mode when (CPWMS = 1).
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
433
Functional description
FTM counter = CNTIN
counter overflow
FTM counter =
MOD
counter overflow
FTM counter =
MOD
channel (n) match
(FTM counting
is up)
channel (n) match
(FTM counting
is down)
channel (n) output
pulse width
2 x (CnV - CNTIN)
period
2 x (MOD - CNTINCNTIN)
Figure 26-180. CPWM period and pulse width with ELSnB:ELSnA = 1:0
If (ELSnB:ELSnA = 0:0) when the FTM counter reaches the value in the CnV register,
the CHnF bit is set and the channel (n) interrupt is generated (if CHnIE = 1), however the
channel (n) output is not controlled by FTM.
If (ELSnB:ELSnA = 1:0), then the channel (n) output is forced high at the channel (n)
match (FTM counter = CnV) when counting down, and it is forced low at the channel (n)
match when counting up. See the following figure.
counter
overflow
channel (n) match in
down counting
MOD = 0x0008
CnV = 0x0005
CNT
...
7
8
7
6
5
4
3
counter
overflow
channel (n) match in
down counting
channel (n) match in
up counting
2
1
0
1
2
3
4
5
7
6
8
7
6
5
...
channel (n) output
CHnF bit
previous value
TOF bit
Figure 26-181. CPWM signal with ELSnB:ELSnA = 1:0
If (ELSnB:ELSnA = X:1), then the channel (n) output is forced low at the channel (n)
match (FTM counter = CnV) when counting down, and it is forced high at the channel (n)
match when counting up. See the following figure.
counter
overflow
counter
overflow
MOD = 0x0008
CnV = 0x0005
channel (n) match in
down counting
CNT
...
7
8
7
6
5
4
3
channel (n) match in
up counting
2
1
0
1
2
3
4
5
6
channel (n) match in
down counting
7
8
7
6
5
...
channel (n) output
CHnF bit
previous value
TOF bit
Figure 26-182. CPWM signal with ELSnB:ELSnA = X:1
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
434
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
If (CnV = 0x0000) or CnV is a negative value, that is (CnV[15] = 1), then the channel (n)
output is a 0% duty cycle CPWM signal and CHnF bit is not set even when there is the
channel (n) match.
If CnV is a positive value, that is (CnV[15] = 0), (CnV ≥ MOD), and (MOD ≠ 0x0000),
then the channel (n) output is a 100% duty cycle CPWM signal and CHnF bit is not set
even when there is the channel (n) match. This implies that the usable range of periods
set by MOD is 0x0001 through 0x7FFE, 0x7FFF if you do not need to generate a 100%
duty cycle CPWM signal. This is not a significant limitation because the resulting period
is much longer than required for normal applications.
The CPWM mode must not be used when the FTM counter is a free running counter.
Note
The CPWM mode must be used only with CNTIN = 0x0000.
26.4.8 Combine mode
The Combine mode is selected when:
•
•
•
•
FTMEN = 1
DECAPEN = 0
COMBINE = 1, and
CPWMS = 0
In Combine mode, an even channel (n) and adjacent odd channel (n+1) are combined to
generate a PWM signal in the channel (n) output.
In the Combine mode, the PWM period is determined by (MOD − CNTIN + 0x0001) and
the PWM pulse width (duty cycle) is determined by (|C(n+1)V − C(n)V|).
The CHnF bit is set and the channel (n) interrupt is generated (if CHnIE = 1) at the
channel (n) match (FTM counter = C(n)V). The CH(n+1)F bit is set and the channel (n
+1) interrupt is generated, if CH(n+1)IE = 1, at the channel (n+1) match (FTM counter =
C(n+1)V).
If (ELSnB:ELSnA = 1:0), then the channel (n) output is forced low at the beginning of
the period (FTM counter = CNTIN) and at the channel (n+1) match (FTM counter = C(n
+1)V). It is forced high at the channel (n) match (FTM counter = C(n)V). See the
following figure.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
435
Functional description
If (ELSnB:ELSnA = X:1), then the channel (n) output is forced high at the beginning of
the period (FTM counter = CNTIN) and at the channel (n+1) match (FTM counter = C(n
+1)V). It is forced low at the channel (n) match (FTM counter = C(n)V). See the
following figure.
In Combine mode, the ELS(n+1)B and ELS(n+1)A bits are not used in the generation of
the channels (n) and (n+1) output. However, if (ELSnB:ELSnA = 0:0) then the channel
(n) output is not controlled by FTM, and if (ELS(n+1)B:ELS(n+1)A = 0:0) then the
channel (n+1) output is not controlled by FTM.
channel (n+1) match
FTM counter
channel (n) match
channel (n) output
with ELSnB:ELSnA = 1:0
channel (n) output
with ELSnB:ELSnA = X:1
Figure 26-183. Combine mode
The following figures illustrate the PWM signals generation using Combine mode.
FTM counter
MOD
C(n+1)V
C(n)V
CNTIN
channel (n) output
with ELSnB:ELSnA = 1:0
channel (n) output
with ELSnB:ELSnA = X:1
Figure 26-184. Channel (n) output if (CNTIN < C(n)V < MOD) and (CNTIN < C(n+1)V <
MOD) and (C(n)V < C(n+1)V)
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
436
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
FTM counter
MOD = C(n+1)V
C(n)V
CNTIN
channel (n) output
with ELSnB:ELSnA = 1:0
channel (n) output
with ELSnB:ELSnA = X:1
Figure 26-185. Channel (n) output if (CNTIN < C(n)V < MOD) and (C(n+1)V = MOD)
FTM counter
MOD
C(n+1)V
C(n)V = CNTIN
channel (n) output
with ELSnB:ELSnA = 1:0
channel (n) output
with ELSnB:ELSnA = X:1
Figure 26-186. Channel (n) output if (C(n)V = CNTIN) and (CNTIN < C(n+1)V < MOD)
FTM counter
MOD = C(n+1)V
C(n)V
CNTIN
channel (n) output
with ELSnB:ELSnA = 1:0
channel (n) output
with ELSnB:ELSnA = X:1
not fully 100% duty cycle
not fully 0% duty cycle
Figure 26-187. Channel (n) output if (CNTIN < C(n)V < MOD) and (C(n)V is Almost Equal
to CNTIN) and (C(n+1)V = MOD)
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
437
Functional description
FTM counter
MOD
C(n+1)V
C(n)V = CNTIN
channel (n) output
with ELSnB:ELSnA = 1:0
channel (n) output
with ELSnB:ELSnA = X:1
not fully 100% duty cycle
not fully 0% duty cycle
Figure 26-188. Channel (n) output if (C(n)V = CNTIN) and (CNTIN < C(n+1)V < MOD) and
(C(n+1)V is Almost Equal to MOD)
FTM counter
C(n+1)V
MOD
CNTIN
C(n)V
channel (n) output
with ELSnB:ELSnA = 1:0
0% duty cycle
channel (n) output
with ELSnB:ELSnA = X:1
100% duty cycle
Figure 26-189. Channel (n) output if C(n)V and C(n+1)V are not between CNTIN and MOD
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
438
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
FTM counter
MOD
C(n+1)V = C(n)V
CNTIN
channel (n) output
with ELSnB:ELSnA = 1:0
0% duty cycle
channel (n) output
with ELSnB:ELSnA = X:1
100% duty cycle
Figure 26-190. Channel (n) output if (CNTIN < C(n)V < MOD) and (CNTIN < C(n+1)V <
MOD) and (C(n)V = C(n+1)V)
FTM counter
MOD
C(n)V =
C(n+1)V = CNTIN
channel (n) output
with ELSnB:ELSnA = 1:0
channel (n) output
with ELSnB:ELSnA = X:1
0% duty cycle
100% duty cycle
Figure 26-191. Channel (n) output if (C(n)V = C(n+1)V = CNTIN)
MOD =
C(n+1)V =
C(n)V
FTM counter
CNTIN
channel (n) output
with ELSnB:ELSnA = 1:0
channel (n) output
with ELSnB:ELSnA = X:1
0% duty cycle
100% duty cycle
Figure 26-192. Channel (n) output if (C(n)V = C(n+1)V = MOD)
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
439
Functional description
FTM counter
MOD
C(n)V
C(n+1)V
CNTIN
channel (n) output
with ELSnB:ELSnA = 1:0
0% duty cycle
channel (n) output
with ELSnB:ELSnA = X:1
100% duty cycle
channel (n) match
is ignored
Figure 26-193. Channel (n) output if (CNTIN < C(n)V < MOD) and (CNTIN < C(n+1)V <
MOD) and (C(n)V > C(n+1)V)
FTM counter
MOD
C(n+1)V
CNTIN
C(n)V
channel (n) output
with ELSnB:ELSnA = 1:0
0% duty cycle
channel (n) output
with ELSnB:ELSnA = X:1
100% duty cycle
Figure 26-194. Channel (n) output if (C(n)V < CNTIN) and (CNTIN < C(n+1)V < MOD)
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
440
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
FTM counter
MOD
C(n)V
CNTIN
C(n+1)V
channel (n) output
with ELSnB:ELSnA = 1:0
channel (n) output
with ELSnB:ELSnA = X:1
Figure 26-195. Channel (n) output if (C(n+1)V < CNTIN) and (CNTIN < C(n)V < MOD)
FTM counter
C(n)V
MOD
C(n+1)V
CNTIN
channel (n) output
with ELSnB:ELSnA = 1:0
0% duty cycle
channel (n) output
with ELSnB:ELSnA = X:1
100% duty cycle
Figure 26-196. Channel (n) output if (C(n)V > MOD) and (CNTIN < C(n+1)V < MOD)
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
441
Functional description
FTM counter
C(n+1)V
MOD
C(n)V
CNTIN
channel (n) output
with ELSnB:ELSnA = 1:0
channel (n) output
with ELSnB:ELSnA = X:1
Figure 26-197. Channel (n) output if (C(n+1)V > MOD) and (CNTIN < C(n)V < MOD)
FTM counter
C(n+1)V
MOD = C(n)V
CNTIN
channel (n) output
with ELSnB:ELSnA = 1:0
not fully 0% duty cycle
channel (n) output
with ELSnB:ELSnA = X:1
not fully 100% duty cycle
Figure 26-198. Channel (n) output if (C(n+1)V > MOD) and (CNTIN < C(n)V = MOD)
26.4.8.1 Asymmetrical PWM
In Combine mode, the control of the PWM signal first edge, when the channel (n) match
occurs, that is, FTM counter = C(n)V, is independent of the control of the PWM signal
second edge, when the channel (n+1) match occurs, that is, FTM counter = C(n+1)V. So,
Combine mode allows the generation of asymmetrical PWM signals.
26.4.9 Complementary mode
The Complementary mode is selected when:
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
442
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
•
•
•
•
•
FTMEN = 1
DECAPEN = 0
COMBINE = 1
CPWMS = 0, and
COMP = 1
In Complementary mode, the channel (n+1) output is the inverse of the channel (n)
output.
So, the channel (n+1) output is the same as the channel (n) output when:
• FTMEN = 1
• DECAPEN = 0
• COMBINE = 1
• CPWMS = 0, and
• COMP = 0
channel (n+1) match
FTM counter
channel (n) match
channel (n) output
with ELSnB:ELSnA = 1:0
channel (n+1) output
with COMP = 0
channel (n+1) output
with COMP = 1
Figure 26-199. Channel (n+1) output in Complementary mode with (ELSnB:ELSnA = 1:0)
channel (n+1) match
FTM counter
channel (n) match
channel (n) output
with ELSnB:ELSnA = X:1
channel (n+1) output
with COMP = 0
channel (n+1) output
with COMP = 1
Figure 26-200. Channel (n+1) output in Complementary mode with (ELSnB:ELSnA = X:1)
26.4.10 Registers updated from write buffers
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
443
Functional description
26.4.10.1 CNTIN register update
The following table describes when CNTIN register is updated:
Table 26-239. CNTIN register update
When
Then CNTIN register is updated
CLKS[1:0] = 0:0
When CNTIN register is written, independent of FTMEN bit.
• FTMEN = 0, or
• CNTINC = 0
At the next system clock after CNTIN was written.
• FTMEN = 1,
• SYNCMODE = 1, and
• CNTINC = 1
By the CNTIN register synchronization.
26.4.10.2 MOD register update
The following table describes when MOD register is updated:
Table 26-240. MOD register update
When
CLKS[1:0] = 0:0
Then MOD register is updated
When MOD register is written, independent of FTMEN bit.
• CLKS[1:0] ≠ 0:0, and
• FTMEN = 0
According to the CPWMS bit, that is:
• If the selected mode is not CPWM then MOD register is updated after MOD
register was written and the FTM counter changes from MOD to CNTIN. If
the FTM counter is at free-running counter mode then this update occurs
when the FTM counter changes from 0xFFFF to 0x0000.
• If the selected mode is CPWM then MOD register is updated after MOD
register was written and the FTM counter changes from MOD to (MOD –
0x0001).
• CLKS[1:0] ≠ 0:0, and
• FTMEN = 1
By the MOD register synchronization.
26.4.10.3 CnV register update
The following table describes when CnV register is updated:
Table 26-241. CnV register update
When
CLKS[1:0] = 0:0
• CLKS[1:0] ≠ 0:0, and
• FTMEN = 0
Then CnV register is updated
When CnV register is written, independent of FTMEN bit.
According to the selected mode, that is:
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
444
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
Table 26-241. CnV register update (continued)
When
Then CnV register is updated
• If the selected mode is Output Compare, then CnV register is updated on the
next FTM counter change, end of the prescaler counting, after CnV register
was written.
• If the selected mode is EPWM, then CnV register is updated after CnV
register was written and the FTM counter changes from MOD to CNTIN. If
the FTM counter is at free-running counter mode then this update occurs
when the FTM counter changes from 0xFFFF to 0x0000.
• If the selected mode is CPWM, then CnV register is updated after CnV
register was written and the FTM counter changes from MOD to (MOD –
0x0001).
• CLKS[1:0] ≠ 0:0, and
• FTMEN = 1
According to the selected mode, that is:
• If the selected mode is output compare then CnV register is updated
according to the SYNCEN bit. If (SYNCEN = 0) then CnV register is updated
after CnV register was written at the next change of the FTM counter, the
end of the prescaler counting. If (SYNCEN = 1) then CnV register is updated
by the C(n)V and C(n+1)V register synchronization.
• If the selected mode is not output compare and (SYNCEN = 1) then CnV
register is updated by the C(n)V and C(n+1)V register synchronization.
26.4.11 PWM synchronization
The PWM synchronization provides an opportunity to update the MOD, CNTIN, CnV,
OUTMASK, INVCTRL and SWOCTRL registers with their buffered value and force the
FTM counter to the CNTIN register value.
Note
• The PWM synchronization must be used only in Combine
mode.
• The legacy PWM synchronization (SYNCMODE = 0) is a
subset of the enhanced PWM synchronization
(SYNCMODE = 1). Thus, only the enhanced PWM
synchronization must be used.
26.4.11.1 Hardware trigger
Three hardware trigger signal inputs of the FTM module are enabled when TRIGn = 1,
where n = 0, 1 or 2 corresponding to each one of the input signals, respectively. The
hardware trigger input n is synchronized by the system clock. The PWM synchronization
with hardware trigger is initiated when a rising edge is detected at the enabled hardware
trigger inputs.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
445
Functional description
If (HWTRIGMODE = 0) then the TRIGn bit is cleared when 0 is written to it or when the
trigger n event is detected.
In this case, if two or more hardware triggers are enabled (for example, TRIG0 and
TRIG1 = 1) and only trigger 1 event occurs, then only TRIG1 bit is cleared. If a trigger n
event occurs together with a write setting TRIGn bit, then the synchronization is initiated,
but TRIGn bit remains set due to the write operation.
system clock
write 1 to TRIG0 bit
TRIG0 bit
trigger_0 input
synchronized trigger_0
by system clock
trigger 0 event
Note
All hardware trigger inputs have the same behavior.
Figure 26-201. Hardware trigger event with HWTRIGMODE = 0
If HWTRIGMODE = 1, then the TRIGn bit is only cleared when 0 is written to it.
NOTE
The HWTRIGMODE bit must be 1 only with enhanced PWM
synchronization (SYNCMODE = 1).
26.4.11.2 Software trigger
A software trigger event occurs when 1 is written to the SYNC[SWSYNC] bit. The
SWSYNC bit is cleared when 0 is written to it or when the PWM synchronization,
initiated by the software event, is completed.
If another software trigger event occurs (by writing another 1 to the SWSYNC bit) at the
same time the PWM synchronization initiated by the previous software trigger event is
ending, a new PWM synchronization is started and the SWSYNC bit remains equal to 1.
If SYNCMODE = 0 then the SWSYNC bit is also cleared by FTM according to
PWMSYNC and REINIT bits. In this case if (PWMSYNC = 1) or (PWMSYNC = 0 and
REINIT = 0) then SWSYNC bit is cleared at the next selected loading point after that the
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
446
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
software trigger event occurred; see Boundary cycle and loading points and the following
figure. If (PWMSYNC = 0) and (REINIT = 1) then SWSYNC bit is cleared when the
software trigger event occurs.
If SYNCMODE = 1 then the SWSYNC bit is also cleared by FTM according to the
SWRSTCNT bit. If SWRSTCNT = 0 then SWSYNC bit is cleared at the next selected
loading point after that the software trigger event occurred; see the following figure. If
SWRSTCNT = 1 then SWSYNC bit is cleared when the software trigger event occurs.
system clock
write 1 to SWSYNC bit
SWSYNC bit
software trigger event
PWM synchronization
selected loading point
Figure 26-202. Software trigger event
26.4.11.3 Boundary cycle and loading points
The boundary cycle definition is important for the loading points for the registers MOD,
CNTIN, and C(n)V.
In Up counting mode, the boundary cycle is defined as when the counter wraps to its
initial value (CNTIN). If in Up-down counting mode, then the boundary cycle is defined
as when the counter turns from down to up counting and when from up to down counting.
The following figure shows the boundary cycles and the loading points for the registers.
In the Up Counting mode, the loading points are enabled if one of CNTMIN or CTMAX
bits are 1. In the Up-Down Counting mode, the loading points are selected by CNTMIN
and CNTMAX bits, as indicated in the figure. These loading points are safe places for
register updates thus allowing a smooth transitions in PWM waveform generation.
For both counting modes, if neither CNTMIN nor CNTMAX are 1, then the boundary
cycles are not used as loading points for registers updates. See the register
synchronization descriptions in the following sections for details.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
447
Functional description
loading points if CNTMAX = 1 or CNTMIN = 1
CNT = MOD -> CNTIN
up counting mode
loading points if CNTMAX = 1
CNT = (MOD - 0x0001) -> MOD
up-down counting mode
CNT = (CNTIN + 0x0001) -> CNTIN
loading points if CNTMIN = 1
Figure 26-203. Boundary cycles and loading points
26.4.11.4 MOD register synchronization
The MOD register synchronization updates the MOD register with its buffer value. This
synchronization is enabled if (FTMEN = 1).
The MOD register synchronization can be done by either the enhanced PWM
synchronization (SYNCMODE = 1) or the legacy PWM synchronization (SYNCMODE
= 0). However, it is expected that the MOD register be synchronized only by the
enhanced PWM synchronization.
In the case of enhanced PWM synchronization, the MOD register synchronization
depends on SWWRBUF, SWRSTCNT, HWWRBUF, and HWRSTCNT bits according to
this flowchart:
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
448
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
begin
legacy
PWM synchronization
SYNCMODE
bit ?
=0
=1
enhanced PWM synchronization
MOD register is
updated by hardware trigger
MOD register is
updated by software trigger
HWWRBUF = 0
bit ?
SWWRBUF = 0
bit ?
=1
=1
end
software
trigger
0=
SWSYNC
bit ?
end
hardware
trigger
TRIGn
bit ?
=1
=0
=1
FTM counter is reset by
software trigger
SWRSTCNT
bit ?
wait hardware trigger n
=1
=0
wait the next selected
loading point
HWTRIGMODE
bit ?
=1
=0
update MOD with
its buffer value
update MOD with
its buffer value
clear SWSYNC bit
clear SWSYNC bit
end
end
clear TRIGn bit
FTM counter is reset by
hardware trigger
0=
HWRSTCNT
bit ?
=1
wait the next selected
loading point
update MOD with
its buffer value
update MOD with
its buffer value
end
end
Figure 26-204. MOD register synchronization flowchart
In the case of legacy PWM synchronization, the MOD register synchronization depends
on PWMSYNC and REINIT bits according to the following description.
If (SYNCMODE = 0), (PWMSYNC = 0), and (REINIT = 0), then this synchronization is
made on the next selected loading point after an enabled trigger event takes place. If the
trigger event was a software trigger, then the SWSYNC bit is cleared on the next selected
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
449
Functional description
loading point. If the trigger event was a hardware trigger, then the trigger enable bit
(TRIGn) is cleared according to Hardware trigger. Examples with software and hardware
triggers follow.
system clock
write 1 to SWSYNC bit
SWSYNC bit
software trigger event
selected loading point
MOD register is updated
Figure 26-205. MOD synchronization with (SYNCMODE = 0), (PWMSYNC = 0), (REINIT =
0), and software trigger was used
system clock
write 1 to TRIG0 bit
TRIG0 bit
trigger 0 event
selected loading point
MOD register is updated
Figure 26-206. MOD synchronization with (SYNCMODE = 0), (HWTRIGMODE = 0),
(PWMSYNC = 0), (REINIT = 0), and a hardware trigger was used
If (SYNCMODE = 0), (PWMSYNC = 0), and (REINIT = 1), then this synchronization is
made on the next enabled trigger event. If the trigger event was a software trigger, then
the SWSYNC bit is cleared according to the following example. If the trigger event was a
hardware trigger, then the TRIGn bit is cleared according to Hardware trigger. Examples
with software and hardware triggers follow.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
450
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
system clock
write 1 to SWSYNC bit
SWSYNC bit
software trigger event
MOD register is updated
Figure 26-207. MOD synchronization with (SYNCMODE = 0), (PWMSYNC = 0), (REINIT =
1), and software trigger was used
system clock
write 1 to TRIG0 bit
TRIG0 bit
trigger 0 event
MOD register is updated
Figure 26-208. MOD synchronization with (SYNCMODE = 0), (HWTRIGMODE = 0),
(PWMSYNC = 0), (REINIT = 1), and a hardware trigger was used
If (SYNCMODE = 0) and (PWMSYNC = 1), then this synchronization is made on the
next selected loading point after the software trigger event takes place. The SWSYNC bit
is cleared on the next selected loading point:
system clock
write 1 to SWSYNC bit
SWSYNC bit
software trigger event
selected loading point
MOD register is updated
Figure 26-209. MOD synchronization with (SYNCMODE = 0) and (PWMSYNC = 1)
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
451
Functional description
26.4.11.5 CNTIN register synchronization
The CNTIN register synchronization updates the CNTIN register with its buffer value.
This synchronization is enabled if (FTMEN = 1), (SYNCMODE = 1), and (CNTINC =
1). The CNTIN register synchronization can be done only by the enhanced PWM
synchronization (SYNCMODE = 1). The synchronization mechanism is the same as the
MOD register synchronization done by the enhanced PWM synchronization; see MOD
register synchronization.
26.4.11.6 C(n)V and C(n+1)V register synchronization
The C(n)V and C(n+1)V registers synchronization updates the C(n)V and C(n+1)V
registers with their buffer values.
This synchronization is enabled if (FTMEN = 1) and (SYNCEN = 1). The
synchronization mechanism is the same as the MOD register synchronization. However,
it is expected that the C(n)V and C(n+1)V registers be synchronized only by the
enhanced PWM synchronization (SYNCMODE = 1).
26.4.11.7 OUTMASK register synchronization
The OUTMASK register synchronization updates the OUTMASK register with its buffer
value.
The OUTMASK register can be updated at each rising edge of system clock
(SYNCHOM = 0), by the enhanced PWM synchronization (SYNCHOM = 1 and
SYNCMODE = 1) or by the legacy PWM synchronization (SYNCHOM = 1 and
SYNCMODE = 0). However, it is expected that the OUTMASK register be synchronized
only by the enhanced PWM synchronization.
In the case of enhanced PWM synchronization, the OUTMASK register synchronization
depends on SWOM and HWOM bits. See the following flowchart:
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
452
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
begin
update OUTMASK register at
each rising edge of system clock
no =
0=
SYNCHOM
bit ?
update OUTMASK register by
PWM synchronization
=1
1=
rising edge
of system
clock ?
SYNCMODE
bit ?
=0
legacy
PWM synchronization
= yes
update OUTMASK
with its buffer value
end
enhanced PWM synchronization
OUTMASK is updated
by hardware trigger
OUTMASK is updated
by software trigger
1=
0=
SWSYNC
bit ?
SWOM
bit ?
software
trigger
=0
end
0=
end
HWOM
bit ?
=1
hardware
trigger
TRIGn
bit ?
=1
=1
update OUTMASK
with its buffer value
end
=0
wait hardware trigger n
update OUTMASK
with its buffer value
HWTRIGMODE
bit ?
=1
=0
clear TRIGn bit
end
Figure 26-210. OUTMASK register synchronization flowchart
In the case of legacy PWM synchronization, the OUTMASK register synchronization
depends on PWMSYNC bit according to the following description.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
453
Functional description
If (SYNCMODE = 0), (SYNCHOM = 1), and (PWMSYNC = 0), then this
synchronization is done on the next enabled trigger event. If the trigger event was a
software trigger, then the SWSYNC bit is cleared on the next selected loading point. If
the trigger event was a hardware trigger, then the TRIGn bit is cleared according to
Hardware trigger. Examples with software and hardware triggers follow.
system clock
write 1 to SWSYNC bit
SWSYNC bit
software trigger event
selected loading point
OUTMASK register is updated
SWSYNC bit is cleared
Figure 26-211. OUTMASK synchronization with (SYNCMODE = 0), (SYNCHOM = 1),
(PWMSYNC = 0) and software trigger was used
system clock
write 1 to TRIG0 bit
TRIG0 bit
trigger 0 event
OUTMASK register is updated and
TRIG0 bit is cleared
Figure 26-212. OUTMASK synchronization with (SYNCMODE = 0), (HWTRIGMODE = 0),
(SYNCHOM = 1), (PWMSYNC = 0), and a hardware trigger was used
If (SYNCMODE = 0), (SYNCHOM = 1), and (PWMSYNC = 1), then this
synchronization is made on the next enabled hardware trigger. The TRIGn bit is cleared
according to Hardware trigger. An example with a hardware trigger follows.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
454
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
system clock
write 1 to TRIG0 bit
TRIG0 bit
trigger 0 event
OUTMASK register is updated and
TRIG0 bit is cleared
Figure 26-213. OUTMASK synchronization with (SYNCMODE = 0), (HWTRIGMODE = 0),
(SYNCHOM = 1), (PWMSYNC = 1), and a hardware trigger was used
26.4.11.8 INVCTRL register synchronization
The INVCTRL register synchronization updates the INVCTRL register with its buffer
value.
The INVCTRL register can be updated at each rising edge of system clock (INVC = 0) or
by the enhanced PWM synchronization (INVC = 1 and SYNCMODE = 1) according to
the following flowchart.
In the case of enhanced PWM synchronization, the INVCTRL register synchronization
depends on SWINVC and HWINVC bits.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
455
Functional description
begin
update INVCTRL register at
each rising edge of system clock
0=
INVC
bit ?
=1
update INVCTRL register by
PWM synchronization
1=
no =
SYNCMODE
bit ?
rising edge
of system
clock ?
=0
end
= yes
update INVCTRL
with its buffer value
end
enhanced PWM synchronization
INVCTRL is updated
by hardware trigger
INVCTRL is updated
by software trigger
1=
0=
SWSYNC
bit ?
SWINVC
bit ?
software
trigger
=0
end
0=
end
HWINVC
bit ?
=1
hardware
trigger
end
=0
=1
=1
update INVCTRL
with its buffer value
TRIGn
bit ?
wait hardware trigger n
update INVCTRL
with its buffer value
HWTRIGMODE
bit ?
=1
=0
clear TRIGn bit
end
Figure 26-214. INVCTRL register synchronization flowchart
26.4.11.9 SWOCTRL register synchronization
The SWOCTRL register synchronization updates the SWOCTRL register with its buffer
value.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
456
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
The SWOCTRL register can be updated at each rising edge of system clock (SWOC = 0)
or by the enhanced PWM synchronization (SWOC = 1 and SYNCMODE = 1) according
to the following flowchart.
In the case of enhanced PWM synchronization, the SWOCTRL register synchronization
depends on SWSOC and HWSOC bits.
begin
update SWOCTRL register at
each rising edge of system clock
0=
SWOC
bit ?
=1
update SWOCTRL register by
PWM synchronization
1=
no =
SYNCMODE
bit ?
rising edge
of system
clock ?
=0
end
= yes
update SWOCTRL
with its buffer value
end
enhanced PWM synchronization
SWOCTRL is updated
by hardware trigger
SWOCTRL is updated
by software trigger
1=
0=
SWSYNC
bit ?
SWSOC
bit ?
software
trigger
=0
end
0=
end
HWSOC
bit ?
=1
hardware
trigger
end
=0
=1
=1
update SWOCTRL
with its buffer value
TRIGn
bit ?
wait hardware trigger n
update SWOCTRL
with its buffer value
HWTRIGMODE
bit ?
=1
=0
clear TRIGn bit
end
Figure 26-215. SWOCTRL register synchronization flowchart
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
457
Functional description
26.4.11.10 FTM counter synchronization
The FTM counter synchronization is a mechanism that allows the FTM to restart the
PWM generation at a certain point in the PWM period. The channels outputs are forced
to their initial value, except for channels in Output Compare mode, and the FTM counter
is forced to its initial counting value defined by CNTIN register.
The following figure shows the FTM counter synchronization. Note that after the
synchronization event occurs, the channel (n) is set to its initial value and the channel (n
+1) is not set to its initial value due to a specific timing of this figure in which the
deadtime insertion prevents this channel output from transitioning to 1. If no deadtime
insertion is selected, then the channel (n+1) transitions to logical value 1 immediately
after the synchronization event occurs.
channel (n+1) match
FTM counter
channel (n) match
channel (n) output
(after deadtime
insertion)
channel (n+1) output
(after deadtime
insertion)
synchronization event
Figure 26-216. FTM counter synchronization
The FTM counter synchronization can be done by either the enhanced PWM
synchronization (SYNCMODE = 1) or the legacy PWM synchronization (SYNCMODE
= 0). However, the FTM counter must be synchronized only by the enhanced PWM
synchronization.
In the case of enhanced PWM synchronization, the FTM counter synchronization
depends on SWRSTCNT and HWRSTCNT bits according to the following flowchart.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
458
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
begin
legacy
PWM synchronization
SYNCMODE
bit ?
=0
=1
enhanced PWM synchronization
FTM counter is reset by
software trigger
SWSYNC
bit ?
SWRSTCNT
bit ?
software
trigger
=0
end
=0
1=
FTM counter is reset by
hardware trigger
end
=1
HWRSTCNT
bit ?
hardware
trigger
=0
update the channels outputs
with their initial value
clear SWSYNC bit
=0
=1
=1
update FTM counter with
CNTIN register value
TRIGn
bit ?
wait hardware trigger n
update FTM counter with
CNTIN register value
update the channels outputs
with their initial value
end
HWTRIGMODE
bit ?
=1
=0
clear TRIGn bit
end
Figure 26-217. FTM counter synchronization flowchart
In the case of legacy PWM synchronization, the FTM counter synchronization depends
on REINIT and PWMSYNC bits according to the following description.
If (SYNCMODE = 0), (REINIT = 1), and (PWMSYNC = 0) then this synchronization is
made on the next enabled trigger event. If the trigger event was a software trigger then
the SWSYNC bit is cleared according to the following example. If the trigger event was a
hardware trigger then the TRIGn bit is cleared according to Hardware trigger. Examples
with software and hardware triggers follow.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
459
Functional description
system clock
write 1 to SWSYNC bit
SWSYNC bit
software trigger event
FTM counter is updated with the CNTIN register value
and channel outputs are forced to their initial value
Figure 26-218. FTM counter synchronization with (SYNCMODE = 0), (REINIT = 1),
(PWMSYNC = 0), and software trigger was used
system clock
write 1 to TRIG0 bit
TRIG0 bit
trigger 0 event
FTM counter is updated with the CNTIN register value
and channel outputs are forced to their initial value
Figure 26-219. FTM counter synchronization with (SYNCMODE = 0), (HWTRIGMODE = 0),
(REINIT = 1), (PWMSYNC = 0), and a hardware trigger was used
If (SYNCMODE = 0), (REINIT = 1), and (PWMSYNC = 1) then this synchronization is
made on the next enabled hardware trigger. The TRIGn bit is cleared according to
Hardware trigger.
system clock
write 1 to TRIG0 bit
TRIG0 bit
trigger 0 event
FTM counter is updated with the CNTIN register value
and channel outputs are forced to their initial value
Figure 26-220. FTM counter synchronization with (SYNCMODE = 0), (HWTRIGMODE = 0),
(REINIT = 1), (PWMSYNC = 1), and a hardware trigger was used
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
460
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
26.4.12 Inverting
The invert functionality swaps the signals between channel (n) and channel (n+1)
outputs. The inverting operation is selected when:
•
•
•
•
•
•
FTMEN = 1
DECAPEN = 0
COMBINE = 1
COMP = 1
CPWMS = 0, and
INVm = 1 (where m represents a channel pair)
The INVm bit in INVCTRL register is updated with its buffer value according to
INVCTRL register synchronization
In High-True (ELSnB:ELSnA = 1:0) Combine mode, the channel (n) output is forced low
at the beginning of the period (FTM counter = CNTIN), forced high at the channel (n)
match and forced low at the channel (n+1) match. If the inverting is selected, the channel
(n) output behavior is changed to force high at the beginning of the PWM period, force
low at the channel (n) match and force high at the channel (n+1) match. See the following
figure.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
461
Functional description
channel (n+1) match
FTM counter
channel (n) match
channel (n) output
before the inverting
channel (n+1) output
before the inverting
write 1 to INV(m) bit
INV(m) bit buffer
INVCTRL register
synchronization
INV(m) bit
channel (n) output
after the inverting
channel (n+1) output
after the inverting
NOTE
INV(m) bit selects the inverting to the pair channels (n) and (n+1).
Figure 26-221. Channels (n) and (n+1) outputs after the inverting in High-True
(ELSnB:ELSnA = 1:0) Combine mode
Note that the ELSnB:ELSnA bits value should be considered because they define the
active state of the channels outputs. In Low-True (ELSnB:ELSnA = X:1) Combine mode,
the channel (n) output is forced high at the beginning of the period, forced low at the
channel (n) match and forced high at the channel (n+1) match. When inverting is
selected, the channels (n) and (n+1) present waveforms as shown in the following figure.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
462
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
channel (n+1) match
FTM counter
channel (n) match
channel (n) output
before the inverting
channel (n+1) output
before the inverting
write 1 to INV(m) bit
INV(m) bit buffer
INVCTRL register
synchronization
INV(m) bit
channel (n) output
after the inverting
channel (n+1) output
after the inverting
NOTE
INV(m) bit selects the inverting to the pair channels (n) and (n+1).
Figure 26-222. Channels (n) and (n+1) outputs after the inverting in Low-True
(ELSnB:ELSnA = X:1) Combine mode
Note
The inverting feature must be used only in Combine mode.
26.4.13 Software output control
The software output control forces the channel output according to software defined
values at a specific time in the PWM generation.
The software output control is selected when:
•
•
•
•
•
FTMEN = 1
DECAPEN = 0
COMBINE = 1
CPWMS = 0, and
CHnOC = 1
The CHnOC bit enables the software output control for a specific channel output and the
CHnOCV selects the value that is forced to this channel output.
Both CHnOC and CHnOCV bits in SWOCTRL register are buffered and updated with
their buffer value according to SWOCTRL register synchronization.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
463
Functional description
The following figure shows the channels (n) and (n+1) outputs signals when the software
output control is used. In this case the channels (n) and (n+1) are set to Combine and
Complementary mode.
channel (n+1) match
FTM counter
channel (n) match
channel (n) output
after the software
output control
channel (n+1) output
after the software
output control
CH(n)OC buffer
CH(n+1)OC buffer
write to SWOCTRL register
write to SWOCTRL register
CH(n)OC bit
CH(n+1)OC bit
SWOCTRL register synchronization
SWOCTRL register synchronization
NOTE
CH(n)OCV = 1 and CH(n+1)OCV = 0.
Figure 26-223. Example of software output control in Combine and Complementary
mode
Software output control forces the following values on channels (n) and (n+1) when the
COMP bit is zero.
Table 26-242. Software ouput control behavior when (COMP = 0)
CH(n)OC
CH(n+1)OC
CH(n)OCV
CH(n+1)OCV
Channel (n) Output
Channel (n+1) Output
0
0
X
X
is not modified by SWOC
is not modified by SWOC
1
1
0
0
is forced to zero
is forced to zero
1
1
0
1
is forced to zero
is forced to one
1
1
1
0
is forced to one
is forced to zero
1
1
1
1
is forced to one
is forced to one
Software output control forces the following values on channels (n) and (n+1) when the
COMP bit is one.
Table 26-243. Software ouput control behavior when (COMP = 1)
CH(n)OC
CH(n+1)OC
CH(n)OCV
CH(n+1)OCV
Channel (n) Output
Channel (n+1) Output
0
0
X
X
is not modified by SWOC
is not modified by SWOC
1
1
0
0
is forced to zero
is forced to zero
1
1
0
1
is forced to zero
is forced to one
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
464
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
Table 26-243. Software ouput control behavior when (COMP = 1) (continued)
CH(n)OC
CH(n+1)OC
CH(n)OCV
CH(n+1)OCV
Channel (n) Output
Channel (n+1) Output
1
1
1
0
is forced to one
is forced to zero
1
1
1
1
is forced to one
is forced to zero
Note
• The software output control feature must be used only in
Combine mode.
• The CH(n)OC and CH(n+1)OC bits should be equal.
• The COMP bit must not be modified when software output
control is enabled, that is, CH(n)OC = 1 and/or CH(n
+1)OC = 1.
• Software output control has the same behavior with
disabled or enabled FTM counter (see the CLKS field
description in the Status and Control register).
26.4.14 Deadtime insertion
The deadtime insertion is enabled when (DTEN = 1) and (DTVAL[5:0] is non- zero).
DEADTIME register defines the deadtime delay that can be used for all FTM channels.
The DTPS[1:0] bits define the prescaler for the system clock and the DTVAL[5:0] bits
define the deadtime modulo, that is, the number of the deadtime prescaler clocks.
The deadtime delay insertion ensures that no two complementary signals (channels (n)
and (n+1)) drive the active state at the same time.
If POL(n) = 0, POL(n+1) = 0, and the deadtime is enabled, then when the channel (n)
match (FTM counter = C(n)V) occurs, the channel (n) output remains at the low value
until the end of the deadtime delay when the channel (n) output is set. Similarly, when the
channel (n+1) match (FTM counter = C(n+1)V) occurs, the channel (n+1) output remains
at the low value until the end of the deadtime delay when the channel (n+1) output is set.
See the following figures.
If POL(n) = 1, POL(n+1) = 1, and the deadtime is enabled, then when the channel (n)
match (FTM counter = C(n)V) occurs, the channel (n) output remains at the high value
until the end of the deadtime delay when the channel (n) output is cleared. Similarly,
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
465
Functional description
when the channel (n+1) match (FTM counter = C(n+1)V) occurs, the channel (n+1)
output remains at the high value until the end of the deadtime delay when the channel (n
+1) output is cleared.
channel (n+1) match
FTM counter
channel (n) match
channel (n) output
(before deadtime
insertion)
channel (n+1) output
(before deadtime
insertion)
channel (n) output
(after deadtime
insertion)
channel (n+1) output
(after deadtime
insertion)
Figure 26-224. Deadtime insertion with ELSnB:ELSnA = 1:0, POL(n) = 0, and POL(n+1) =
0
channel (n+1) match
FTM counter
channel (n) match
channel (n) output
(before deadtime
insertion)
channel (n+1) output
(before deadtime
insertion)
channel (n) output
(after deadtime
insertion)
channel (n+1) output
(after deadtime
insertion)
Figure 26-225. Deadtime insertion with ELSnB:ELSnA = X:1, POL(n) = 0, and POL(n+1) =
0
NOTE
The deadtime feature must be used only in Combine and
Complementary modes.
26.4.14.1 Deadtime insertion corner cases
If (PS[2:0] is cleared), (DTPS[1:0] = 0:0 or DTPS[1:0] = 0:1):
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
466
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
• and the deadtime delay is greater than or equal to the channel (n) duty cycle ((C(n
+1)V – C(n)V) × system clock), then the channel (n) output is always the inactive
value (POL(n) bit value).
• and the deadtime delay is greater than or equal to the channel (n+1) duty cycle
((MOD – CNTIN + 1 – (C(n+1)V – C(n)V) ) × system clock), then the channel (n+1)
output is always the inactive value (POL(n+1) bit value).
Although, in most cases the deadtime delay is not comparable to channels (n) and (n+1)
duty cycle, the following figures show examples where the deadtime delay is comparable
to the duty cycle.
channel (n+1) match
FTM counter
channel (n) match
channel (n) output
(before deadtime
insertion)
channel (n+1) output
(before deadtime
insertion)
channel (n) output
(after deadtime
insertion)
channel (n+1) output
(after deadtime
insertion)
Figure 26-226. Example of the deadtime insertion (ELSnB:ELSnA = 1:0, POL(n) = 0, and
POL(n+1) = 0) when the deadtime delay is comparable to channel (n+1) duty cycle
channel (n+1) match
FTM counter
channel (n) match
channel (n) output
(before deadtime
insertion)
channel (n+1) output
(before deadtime
insertion)
channel (n) output
(after deadtime
insertion)
channel (n+1) output
(after deadtime
insertion)
Figure 26-227. Example of the deadtime insertion (ELSnB:ELSnA = 1:0, POL(n) = 0, and
POL(n+1) = 0) when the deadtime delay is comparable to channels (n) and (n+1) duty
cycle
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
467
Functional description
26.4.15 Output mask
The output mask can be used to force channels output to their inactive state through
software. For example: to control a BLDC motor.
Any write to the OUTMASK register updates its write buffer. The OUTMASK register is
updated with its buffer value by PWM synchronization; see OUTMASK register
synchronization.
If CHnOM = 1, then the channel (n) output is forced to its inactive state (POLn bit value).
If CHnOM = 0, then the channel (n) output is unaffected by the output mask. See the
following figure.
the beginning of new PWM cycles
FTM counter
channel (n) output
(before output mask)
CHnOM bit
channel (n) output
(after output mask)
configured PWM signal starts
to be available in the channel (n) output
channel (n) output is disabled
Figure 26-228. Output mask with POLn = 0
The following table shows the output mask result before the polarity control.
Table 26-244. Output mask result for channel (n) before the polarity
control
CHnOM
Output Mask Input
Output Mask Result
0
inactive state
inactive state
active state
active state
inactive state
inactive state
1
active state
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
468
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
Note
The output mask feature must be used only in Combine mode.
26.4.16 Fault control
The fault control is enabled if (FTMEN = 1) and (FAULTM[1:0] ≠ 0:0).
FTM can have up to four fault inputs. FAULTnEN bit (where n = 0, 1, 2, 3) enables the
fault input n and FFLTRnEN bit enables the fault input n filter. FFVAL[3:0] bits select
the value of the enabled filter in each enabled fault input.
First, each fault input signal is synchronized by the system clock; see the synchronizer
block in the following figure. Following synchronization, the fault input n signal enters
the filter block. When there is a state change in the fault input n signal, the 5-bit counter
is reset and starts counting up. As long as the new state is stable on the fault input n, the
counter continues to increment. If the 5-bit counter overflows, that is, the counter exceeds
the value of the FFVAL[3:0] bits, the new fault input n value is validated. It is then
transmitted as a pulse edge to the edge detector.
If the opposite edge appears on the fault input n signal before validation (counter
overflow), the counter is reset. At the next input transition, the counter starts counting
again. Any pulse that is shorter than the minimum value selected by FFVAL[3:0] bits (×
system clock) is regarded as a glitch and is not passed on to the edge detector.
The fault input n filter is disabled when the FFVAL[3:0] bits are zero or when
FAULTnEN = 0. In this case, the fault input n signal is delayed 2 rising edges of the
system clock and the FAULTFn bit is set on 3th rising edge of the system clock after a
rising edge occurs on the fault input n.
If FFVAL[3:0] ≠ 0000 and FAULTnEN = 1, then the fault input n signal is delayed (3 +
FFVAL[3:0]) rising edges of the system clock, that is, the FAULTFn bit is set (4 +
FFVAL[3:0]) rising edges of the system clock after a rising edge occurs on the fault input
n.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
469
Functional description
(FFVAL[3:0] 0000)
and (FFLTRnEN*)
FLTnPOL
synchronizer
fault input n* value
0
fault input n*
system clock
D
CLK
Q
D
Q
CLK
Fault filter
(5-bit counter)
1
fault input
polarity
control
rising edge
detector
FAULTFn*
* where n = 3, 2, 1, 0
Figure 26-229. Fault input n control block diagram
If the fault control and fault input n are enabled and a rising edge at the fault input n
signal is detected, a fault condition has occurred and the FAULTFn bit is set. The
FAULTF bit is the logic OR of FAULTFn[3:0] bits. See the following figure.
fault input 0 value
fault input 1 value
fault input 2 value
fault input 3 value
FAULTIN
FAULTIE
FAULTF0
FAULTF1
fault interrupt
FAULTF
FAULTF2
FAULTF3
Figure 26-230. FAULTF and FAULTIN bits and fault interrupt
If the fault control is enabled (FAULTM[1:0] ≠ 0:0), a fault condition has occurred and
(FAULTEN = 1), then outputs are forced to their safe values:
• Channel (n) output takes the value of POL(n)
• Channel (n+1) takes the value of POL(n+1)
The fault interrupt is generated when (FAULTF = 1) and (FAULTIE = 1). This interrupt
request remains set until:
• Software clears the FAULTF bit by reading FAULTF bit as 1 and writing 0 to it
• Software clears the FAULTIE bit
• A reset occurs
Note
The fault control must be used only in Combine mode.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
470
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
26.4.16.1 Automatic fault clearing
If the automatic fault clearing is selected (FAULTM[1:0] = 1:1), then the channels output
disabled by fault control is again enabled when the fault input signal (FAULTIN) returns
to zero and a new PWM cycle begins. See the following figure.
the beginning of new PWM cycles
FTM counter
channel (n) output
(before fault control)
FAULTIN bit
channel (n) output
FAULTF bit
FAULTF bit is cleared
NOTE
The channel (n) output is after the fault control with automatic fault clearing and POLn = 0.
Figure 26-231. Fault control with automatic fault clearing
26.4.16.2 Manual fault clearing
If the manual fault clearing is selected (FAULTM[1:0] = 0:1 or 1:0), then the channels
output disabled by fault control is again enabled when the FAULTF bit is cleared and a
new PWM cycle begins. See the following figure.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
471
Functional description
the beginning of new PWM cycles
FTM counter
channel (n) output
(before fault control)
FAULTIN bit
channel (n) output
FAULTF bit
FAULTF bit is cleared
NOTE
The channel (n) output is after the fault control with manual fault clearing and POLn = 0.
Figure 26-232. Fault control with manual fault clearing
26.4.16.3 Fault inputs polarity control
The FLTjPOL bit selects the fault input j polarity, where j = 0, 1, 2, 3:
• If FLTjPOL = 0, the fault j input polarity is high, so the logical one at the fault input j
indicates a fault.
• If FLTjPOL = 1, the fault j input polarity is low, so the logical zero at the fault input j
indicates a fault.
26.4.17 Polarity control
The POLn bit selects the channel (n) output polarity:
• If POLn = 0, the channel (n) output polarity is high, so the logical one is the active
state and the logical zero is the inactive state.
• If POLn = 1, the channel (n) output polarity is low, so the logical zero is the active
state and the logical one is the inactive state.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
472
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
Note
The polarity control must be used only in Combine mode.
26.4.18 Initialization
The initialization forces the CHnOI bit value to the channel (n) output when a one is
written to the INIT bit.
The initialization depends on COMP and DTEN bits. The following table shows the
values that channels (n) and (n+1) are forced by initialization when the COMP and
DTEN bits are zero.
Table 26-245. Initialization behavior when (COMP = 0 and DTEN = 0)
CH(n)OI
CH(n+1)OI
Channel (n) Output
Channel (n+1) Output
0
0
is forced to zero
is forced to zero
0
1
is forced to zero
is forced to one
1
0
is forced to one
is forced to zero
1
1
is forced to one
is forced to one
The following table shows the values that channels (n) and (n+1) are forced by
initialization when (COMP = 1) or (DTEN = 1).
Table 26-246. Initialization behavior when (COMP = 1 or DTEN = 1)
CH(n)OI
CH(n+1)OI
Channel (n) Output
Channel (n+1) Output
0
X
is forced to zero
is forced to one
1
X
is forced to one
is forced to zero
Note
The initialization feature must be used only in Combine mode
and with disabled FTM counter. See the description of the
CLKS field in the Status and Control register.
26.4.19 Features priority
The following figure shows the priority of the features used at the generation of channels
(n) and (n+1) outputs signals.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
473
Functional description
pair channels (m) - channels (n) and (n+1)
FTM counter
DECAPEN
COMBINE(m)
CPWMS
C(n)V
MS(n)B
CH(n)OC
MS(n)A
CH(n)OCV
POL(n)
ELS(n)B
CH(n+1)OC
POL(n+1)
ELS(n)A
CH(n)OI
CH(n+1)OI
COMP(m)
INV(m)EN
CH(n+1)OCV
CH(n)OM
DTEN(m) CH(n+1)OM FAULTEN(m)
channel
(n)
output
signal
generation of
channel (n)
output signal
initialization
complementary
mode
inverting
software
output
control
deadtime
insertion
output
mask
fault
control
polarity
control
channel
(n+1)
output
signal
generation of
channel (n+1)
output signal
C(n+1)V
MS(n+1)B
MS(n+1)A
ELS(n+1)B
ELS(n+1)A
NOTE
The channels (n) and (n+1) are in output compare, EPWM, CPWM or combine modes.
Figure 26-233. Priority of the features used at the generation of channels (n) and (n+1)
outputs signals
Note
The Initialization feature must not be used with Inverting and
Software output control features.
26.4.20 Channel trigger output
If CHjTRIG = 1, where j = 0, 1, 2, 3, 4, or 5, then the FTM generates a trigger when the
channel (j) match occurs (FTM counter = C(j)V).
The channel trigger output provides a trigger signal that is used for on-chip modules.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
474
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
The FTM is able to generate multiple triggers in one PWM period. Because each trigger
is generated for a specific channel, several channels are required to implement this
functionality. This behavior is described in the following figure.
the beginning of new PWM cycles
MOD
FTM counter = C5V
FTM counter = C4V
FTM counter = C3V
FTM counter = C2V
FTM counter = C1V
FTM counter = C0V
CNTIN
(a)
(b)
(c)
(d)
NOTE
(a) CH0TRIG = 0, CH1TRIG = 0, CH2TRIG = 0, CH3TRIG = 0, CH4TRIG = 0, CH5TRIG = 0
(b) CH0TRIG = 1, CH1TRIG = 0, CH2TRIG = 0, CH3TRIG = 0, CH4TRIG = 0, CH5TRIG = 0
(c) CH0TRIG = 0, CH1TRIG = 0, CH2TRIG = 0, CH3TRIG = 1, CH4TRIG = 1, CH5TRIG = 1
(d) CH0TRIG = 1, CH1TRIG = 1, CH2TRIG = 1, CH3TRIG = 1, CH4TRIG = 1, CH5TRIG = 1
Figure 26-234. Channel match trigger
Note
The channel match trigger must be used only in Combine mode.
26.4.21 Initialization trigger
If INITTRIGEN = 1, then the FTM generates a trigger when the FTM counter is updated
with the CNTIN register value in the following cases.
• The FTM counter is automatically updated with the CNTIN register value by the
selected counting mode.
• When there is a write to CNT register.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
475
Functional description
• When there is the FTM counter synchronization.
• If (CNT = CNTIN), (CLKS[1:0] = 0:0), and a value different from zero is written to
CLKS[1:0] bits.
The following figures show these cases.
CNTIN = 0x0000
MOD = 0x000F
CPWMS = 0
system clock
FTM counter 0x0C 0x0D 0x0E 0x0F 0x00 0x01 0x02 0x03 0x04 0x05
initialization trigger
Figure 26-235. Initialization trigger is generated when the FTM counting achieves the
CNTIN register value
CNTIN = 0x0000
MOD = 0x000F
CPWMS = 0
system clock
FTM counter 0x04 0x05 0x06 0x00 0x01 0x02 0x03 0x04 0x05 0x06
write to CNT
initialization trigger
Figure 26-236. Initialization trigger is generated when there is a write to CNT register
CNTIN = 0x0000
MOD = 0x000F
CPWMS = 0
system clock
FTM counter 0x04 0x05 0x06 0x07 0x00 0x01 0x02 0x03 0x04 0x05
FTM counter
synchronization
initialization trigger
Figure 26-237. Initialization trigger is generated when there is the FTM counter
synchronization
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
476
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
CNTIN = 0x0000
MOD = 0x000F
CPWMS = 0
system clock
0x00
FTM counter
CLKS[1:0] bits
00
0x01 0x02 0x03 0x04 0x05
01
initialization trigger
Figure 26-238. Initialization trigger is generated if (CNT = CNTIN), (CLKS[1:0] = 0:0), and
a value different from zero is written to CLKS[1:0] bits
The initialization trigger output provides a trigger signal that is used for on-chip modules.
Note
The initialization trigger must be used only in Combine mode.
26.4.22 Capture Test mode
The Capture Test mode allows to test the CnV registers, the FTM counter and the
interconnection logic between the FTM counter and CnV registers.
In this test mode, all channels must be configured for Input Capture mode and FTM
counter must be configured to the Up counting.
When the Capture Test mode is enabled (CAPTEST = 1), the FTM counter is frozen and
any write to CNT register updates directly the FTM counter; see the following figure.
After it was written, all CnV registers are updated with the written value to CNT register
and CHnF bits are set. Therefore, the FTM counter is updated with its next value
according to its configuration. Its next value depends on CNTIN, MOD, and the written
value to FTM counter.
The next reads of CnV registers return the written value to the FTM counter and the next
reads of CNT register return FTM counter next value.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
477
Functional description
FTM counter clock
set CAPTEST
clear CAPTEST
write to MODE
CAPTEST bit
FTM counter
0x1053 0x1054 0x1055
0x1056
0x78AE 0x78AF 0x78B0
0x78AD
0x78AC
write 0x78AC
write to CNT
CHnF bit
0x78AC
0x0300
CnV
NOTE
- FTM counter configuration: (FTMEN = 1), (CAPTEST = 1), (CPWMS = 0), (CNTIN = 0x0000), and (MOD = 0xFFFF)
- FTM channel n configuration: input capture mode - (DECAPEN = 0), (COMBINE = 0), and (MSnB:MSnA = 0:0)
Figure 26-239. Capture Test mode
26.4.23 Dual Edge Capture mode
The Dual Edge Capture mode is selected if FTMEN = 1 and DECAPEN = 1. This mode
allows to measure a pulse width or period of the signal on the input of channel (n) of a
channel pair. The channel (n) filter can be active in this mode when n is 0 or 2.
FTMEN
DECAPEN
is filter
DECAP
enabled?
MS(n)A
ELS(n)B:ELS(n)A
ELS(n+1)B:ELS(n+1)A
0
synchronizer
channel (n) input
system clock
Q
D
CLK
D
CLK
Q
CH(n)IE
CH(n)F
C(n)V[15:0]
Dual edge capture
mode logic
Filter*
1
channel (n)
interrupt
CH(n+1)IE
CH(n+1)F
channel (n+1)
interrupt
C(n+1)V[15:0]
* Filtering function for dual edge capture mode is only available in the channels 0 and 2
FTM counter
Figure 26-240. Dual Edge Capture mode block diagram
The MS(n)A bit defines if the Dual Edge Capture mode is one-shot or continuous.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
478
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
The ELS(n)B:ELS(n)A bits select the edge that is captured by channel (n), and ELS(n
+1)B:ELS(n+1)A bits select the edge that is captured by channel (n+1). If both
ELS(n)B:ELS(n)A and ELS(n+1)B:ELS(n+1)A bits select the same edge, then it is the
period measurement. If these bits select different edges, then it is a pulse width
measurement.
In the Dual Edge Capture mode, only channel (n) input is used and channel (n+1) input is
ignored.
If the selected edge by channel (n) bits is detected at channel (n) input, then CH(n)F bit is
set and the channel (n) interrupt is generated (if CH(n)IE = 1). If the selected edge by
channel (n+1) bits is detected at channel (n) input and (CH(n)F = 1), then CH(n+1)F bit is
set and the channel (n+1) interrupt is generated (if CH(n+1)IE = 1).
The C(n)V register stores the value of FTM counter when the selected edge by channel
(n) is detected at channel (n) input. The C(n+1)V register stores the value of FTM
counter when the selected edge by channel (n+1) is detected at channel (n) input.
In this mode, a coherency mechanism ensures coherent data when the C(n)V and C(n
+1)V registers are read. The only requirement is that C(n)V must be read before C(n
+1)V.
Note
• The CH(n)F, CH(n)IE, MS(n)A, ELS(n)B, and ELS(n)A
bits are channel (n) bits.
• The CH(n+1)F, CH(n+1)IE, MS(n+1)A, ELS(n+1)B, and
ELS(n+1)A bits are channel (n+1) bits.
• The Dual Edge Capture mode must be used with
ELS(n)B:ELS(n)A = 0:1 or 1:0, ELS(n+1)B:ELS(n+1)A =
0:1 or 1:0 and the FTM counter in Free running counter.
26.4.23.1 One-Shot Capture mode
The One-Shot Capture mode is selected when (FTMEN = 1), (DECAPEN = 1), and
(MS(n)A = 0). In this capture mode, only one pair of edges at the channel (n) input is
captured. The ELS(n)B:ELS(n)A bits select the first edge to be captured, and ELS(n
+1)B:ELS(n+1)A bits select the second edge to be captured.
The edge captures are enabled while DECAP bit is set. For each new measurement in
One-Shot Capture mode, first the CH(n)F and CH(n+1) bits must be cleared, and then the
DECAP bit must be set.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
479
Functional description
In this mode, the DECAP bit is automatically cleared by FTM when the edge selected by
channel (n+1) is captured. Therefore, while DECAP bit is set, the one-shot capture is in
process. When this bit is cleared, both edges were captured and the captured values are
ready for reading in the C(n)V and C(n+1)V registers.
Similarly, when the CH(n+1)F bit is set, both edges were captured and the captured
values are ready for reading in the C(n)V and C(n+1)V registers.
26.4.23.2 Continuous Capture mode
The Continuous Capture mode is selected when (FTMEN = 1), (DECAPEN = 1), and
(MS(n)A = 1). In this capture mode, the edges at the channel (n) input are captured
continuously. The ELS(n)B:ELS(n)A bits select the initial edge to be captured, and
ELS(n+1)B:ELS(n+1)A bits select the final edge to be captured.
The edge captures are enabled while DECAP bit is set. For the initial use, first the
CH(n)F and CH(n+1)F bits must be cleared, and then DECAP bit must be set to start the
continuous measurements.
When the CH(n+1)F bit is set, both edges were captured and the captured values are
ready for reading in the C(n)V and C(n+1)V registers. The latest captured values are
always available in these registers even after the DECAP bit is cleared.
In this mode, it is possible to clear only the CH(n+1)F bit. Therefore, when the CH(n+1)F
bit is set again, the latest captured values are available in C(n)V and C(n+1)V registers.
For a new sequence of the measurements in the Dual Edge Capture – Continuous mode,
clear the CH(n)F and CH(n+1)F bits to start new measurements.
26.4.23.3 Pulse width measurement
If the channel (n) is configured to capture rising edges (ELS(n)B:ELS(n)A = 0:1) and the
channel (n+1) to capture falling edges (ELS(n+1)B:ELS(n+1)A = 1:0), then the positive
polarity pulse width is measured. If the channel (n) is configured to capture falling edges
(ELS(n)B:ELS(n)A = 1:0) and the channel (n+1) to capture rising edges (ELS(n
+1)B:ELS(n+1)A = 0:1), then the negative polarity pulse width is measured.
The pulse width measurement can be made in One-Shot Capture mode or Continuous
Capture mode.
The following figure shows an example of the Dual Edge Capture – One-Shot mode used
to measure the positive polarity pulse width. The DECAPEN bit selects the Dual Edge
Capture mode, so it remains set. The DECAP bit is set to enable the measurement of next
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
480
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
positive polarity pulse width. The CH(n)F bit is set when the first edge of this pulse is
detected, that is, the edge selected by ELS(n)B:ELS(n)A bits. The CH(n+1)F bit is set
and DECAP bit is cleared when the second edge of this pulse is detected, that is, the edge
selected by ELS(n+1)B:ELS(n+1)A bits. Both DECAP and CH(n+1)F bits indicate when
two edges of the pulse were captured and the C(n)V and C(n+1)V registers are ready for
reading.
4
FTM counter
12
8
3
7
2
6
1
16
11
10
5
20
15
14
9
13
24
19
28
23
18
27
22
17
26
21
25
channel (n) input
(after the filter
channel input)
DECAPEN bit
set DECAPEN
DECAP bit
set DECAP
C(n)V
1
3
5
7
9
15
2
4
6
8
10
16
19
CH(n)F bit
clear CH(n)F
C(n+1)V
20
22
24
CH(n+1)F bit
clear CH(n+1)F
problem 1 problem 2
Note
- The commands set DECAPEN, set DECAP, clear CH(n)F, and clear CH(n+1)F are made by the user.
- Problem 1: channel (n) input = 1, set DECAP, not clear CH(n)F, and clear CH(n+1)F.
- Problem 2: channel (n) input = 1, set DECAP, not clear CH(n)F, and not clear CH(n+1)F.
Figure 26-241. Dual Edge Capture – One-Shot mode for positive polarity pulse width
measurement
The following figure shows an example of the Dual Edge Capture – Continuous mode
used to measure the positive polarity pulse width. The DECAPEN bit selects the Dual
Edge Capture mode, so it remains set. While the DECAP bit is set the configured
measurements are made. The CH(n)F bit is set when the first edge of the positive polarity
pulse is detected, that is, the edge selected by ELS(n)B:ELS(n)A bits. The CH(n+1)F bit
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
481
Functional description
is set when the second edge of this pulse is detected, that is, the edge selected by ELS(n
+1)B:ELS(n+1)A bits. The CH(n+1)F bit indicates when two edges of the pulse were
captured and the C(n)V and C(n+1)V registers are ready for reading.
4
FTM counter
12
8
3
7
2
6
1
16
11
10
5
20
15
14
9
13
24
19
28
23
18
27
22
17
26
21
25
channel (n) input
(after the filter
channel input)
DECAPEN bit
set DECAPEN
DECAP bit
set DECAP
C(n)V
1
3
5
7
9
11
15
19
21
23
2
4
6
8
10
12
16
20
22
24
CH(n)F bit
clear CH(n)F
C(n+1)V
CH(n+1)F bit
clear CH(n+1)F
Note
- The commands set DECAPEN, set DECAP, clear CH(n)F, and clear CH(n+1)F are made by the user.
Figure 26-242. Dual Edge Capture – Continuous mode for positive polarity pulse width
measurement
26.4.23.4 Period measurement
If the channels (n) and (n+1) are configured to capture consecutive edges of the same
polarity, then the period of the channel (n) input signal is measured. If both channels (n)
and (n+1) are configured to capture rising edges (ELS(n)B:ELS(n)A = 0:1 and ELS(n
+1)B:ELS(n+1)A = 0:1), then the period between two consecutive rising edges is
measured. If both channels (n) and (n+1) are configured to capture falling edges
(ELS(n)B:ELS(n)A = 1:0 and ELS(n+1)B:ELS(n+1)A = 1:0), then the period between
two consecutive falling edges is measured.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
482
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
The period measurement can be made in One-Shot Capture mode or Continuous Capture
mode.
The following figure shows an example of the Dual Edge Capture – One-Shot mode used
to measure the period between two consecutive rising edges. The DECAPEN bit selects
the Dual Edge Capture mode, so it remains set. The DECAP bit is set to enable the
measurement of next period. The CH(n)F bit is set when the first rising edge is detected,
that is, the edge selected by ELS(n)B:ELS(n)A bits. The CH(n+1)F bit is set and DECAP
bit is cleared when the second rising edge is detected, that is, the edge selected by ELS(n
+1)B:ELS(n+1)A bits. Both DECAP and CH(n+1)F bits indicate when two selected
edges were captured and the C(n)V and C(n+1)V registers are ready for reading.
4
8
3
FTM counter
2
11
6
1
16
12
7
10
5
20
15
27
22
17
13
28
23
18
14
9
24
19
21
26
25
channel (n) input
(after the filter
channel input)
DECAPEN bit
set DECAPEN
DECAP bit
set DECAP
C(n)V
1
3
5
6
7
14
17
2
4
6
7
9
15
18
18
20
27
23
26
CH(n)F bit
clear CH(n)F
C(n+1)V
20
CH(n+1)F bit
clear CH(n+1)F
problem 1
problem 2
problem 3
Note
- The commands set DECAPEN, set DECAP, clear CH(n)F, and clear CH(n+1)F are made by the user.
- Problem 1: channel (n) input = 0, set DECAP, not clear CH(n)F, and not clear CH(n+1)F.
- Problem 2: channel (n) input = 1, set DECAP, not clear CH(n)F, and clear CH(n+1)F.
- Problem 3: channel (n) input = 1, set DECAP, not clear CH(n)F, and not clear CH(n+1)F.
Figure 26-243. Dual Edge Capture – One-Shot mode to measure of the period between
two consecutive rising edges
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
483
Functional description
The following figure shows an example of the Dual Edge Capture – Continuous mode
used to measure the period between two consecutive rising edges. The DECAPEN bit
selects the Dual Edge Capture mode, so it remains set. While the DECAP bit is set the
configured measurements are made. The CH(n)F bit is set when the first rising edge is
detected, that is, the edge selected by ELS(n)B:ELS(n)A bits. The CH(n+1)F bit is set
when the second rising edge is detected, that is, the edge selected by ELS(n+1)B:ELS(n
+1)A bits. The CH(n+1)F bit indicates when two edges of the period were captured and
the C(n)V and C(n+1)V registers are ready for reading.
4
FTM counter
12
8
3
2
6
1
16
11
7
9
24
19
14
10
5
20
15
18
13
28
23
27
22
17
21
26
25
channel (n) input
(after the filter
channel input)
DECAPEN bit
set DECAPEN
DECAP bit
set DECAP
C(n)V
1
3
5
6
7
8
9
10 11
12
14 15
16
18 19 20 21 22 23
24
26
2
4
6
7
8
9
10 11 12
13
15 16
17
19 20 21 22 23 24
25
27
CH(n)F bit
clear CH(n)F
C(n+1)V
CH(n+1)F bit
clear CH(n+1)F
Note
- The commands set DECAPEN, set DECAP, clear CH(n)F, and clear CH(n+1)F are made by the user.
Figure 26-244. Dual Edge Capture – Continuous mode to measure of the period between
two consecutive rising edges
26.4.23.5 Read coherency mechanism
The Dual Edge Capture mode implements a read coherency mechanism between the
FTM counter value captured in C(n)V and C(n+1)V registers. The read coherency
mechanism is illustrated in the following figure. In this example, the channels (n) and (n
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
484
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
+1) are in Dual Edge Capture – Continuous mode for positive polarity pulse width
measurement. Thus, the channel (n) is configured to capture the FTM counter value when
there is a rising edge at channel (n) input signal, and channel (n+1) to capture the FTM
counter value when there is a falling edge at channel (n) input signal.
When a rising edge occurs in the channel (n) input signal, the FTM counter value is
captured into channel (n) capture buffer. The channel (n) capture buffer value is
transferred to C(n)V register when a falling edge occurs in the channel (n) input signal.
C(n)V register has the FTM counter value when the previous rising edge occurred, and
the channel (n) capture buffer has the FTM counter value when the last rising edge
occurred.
When a falling edge occurs in the channel (n) input signal, the FTM counter value is
captured into channel (n+1) capture buffer. The channel (n+1) capture buffer value is
transferred to C(n+1)V register when the C(n)V register is read.
In the following figure, the read of C(n)V returns the FTM counter value when the event
1 occurred and the read of C(n+1)V returns the FTM counter value when the event 2
occurred.
event 1
FTM counter
1
event 2
2
event 3
event 4
event 5
4
5
3
event 6
6
event 7
7
event 8
8
event 9
9
channel (n) input
(after the filter
channel input)
channel (n)
capture buffer
1
C(n)V
3
1
channel (n+1)
capture buffer
2
C(n+1)V
5
7
9
3
5
7
4
6
8
2
read C(n)V
read C(n+1)V
Figure 26-245. Dual Edge Capture mode read coherency mechanism
C(n)V register must be read prior to C(n+1)V register in dual edge capture one-shot and
continuous modes for the read coherency mechanism works properly.
26.4.24 Debug mode
When the chip is in Debug mode, the BDMMODE[1:0] bits select the behavior of the
FTM counter, the CH(n)F bit, the channels output, and the writes to the MOD, CNTIN,
and C(n)V registers according to the following table.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
485
Functional description
Table 26-247. FTM behavior when the chip Is in Debug mode
BDMMODE
FTM
Counter
CH(n)F Bit FTM Channels Output
Writes to MOD, CNTIN, and C(n)V Registers
00
Stopped
can be set
Functional mode
Writes to these registers bypass the registers
buffers
01
Stopped
is not set
The channels outputs are forced
to their safe value according to
POLn bit
Writes to these registers bypass the registers
buffers
10
Stopped
is not set
The channels outputs are frozen
when the chip enters in Debug
mode
Writes to these registers bypass the registers
buffers
11
Functional
mode
can be set
Functional mode
Functional mode
Note that if BDMMODE[1:0] = 2’b00 then the channels outputs remain at the value
when the chip enters in Debug mode, because the FTM counter is stopped. However, the
following situations modify the channels outputs in this Debug mode.
• Write any value to CNT register; see Counter reset. In this case, the FTM counter is
updated with the CNTIN register value and the channels outputs are updated to the
initial value – except for those channels set to Output Compare mode.
• FTM counter is reset by PWM Synchronization mode; see FTM counter
synchronization. In this case, the FTM counter is updated with the CNTIN register
value and the channels outputs are updated to the initial value – except for channels
in Output Compare mode.
• In the channels outputs initialization, the channel (n) output is forced to the CH(n)OI
bit value when the value 1 is written to INIT bit. See Initialization.
Note
The BDMMODE[1:0] = 2’b00 must not be used with the Fault
control. Even if the fault control is enabled and a fault condition
exists, the channels outputs values are updated as above.
26.4.25 Intermediate load
The PWMLOAD register allows to update the MOD, CNTIN, and C(n)V registers with
the content of the register buffer at a defined load point. In this case, it is not required to
use the PWM synchronization.
There are multiple possible loading points for intermediate load:
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
486
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
Table 26-248. When possible loading points are enabled
Loading point
Enabled
When the FTM counter wraps from MOD value to CNTIN
value
Always
At the channel (j) match (FTM counter = C(j)V)
When CHjSEL = 1
The following figure shows some examples of enabled loading points.
FTM counter = MOD
FTM counter = C7V
FTM counter = C6V
FTM counter = C5V
FTM counter = C4V
FTM counter = C3V
FTM counter = C2V
FTM counter = C1V
FTM counter = C0V
(a)
(b)
(c)
(d)
(e)
(f)
NOTE
(a) LDOK = 0, CH0SEL = 0, CH1SEL = 0, CH2SEL = 0, CH3SEL = 0, CH4SEL = 0, CH5SEL = 0, CH6SEL = 0, CH7SEL = 0
(b) LDOK = 1, CH0SEL = 0, CH1SEL = 0, CH2SEL = 0, CH3SEL = 0, CH4SEL = 0, CH5SEL = 0, CH6SEL = 0, CH7SEL = 0
(c) LDOK = 0, CH0SEL = 0, CH1SEL = 0, CH2SEL = 0, CH3SEL = 1, CH4SEL = 0, CH5SEL = 0, CH6SEL = 0, CH7SEL = 0
(d) LDOK = 1, CH0SEL = 0, CH1SEL = 0, CH2SEL = 0, CH3SEL = 0, CH4SEL = 0, CH5SEL = 0, CH6SEL = 1, CH7SEL = 0
(e) LDOK = 1, CH0SEL = 1, CH1SEL = 0, CH2SEL = 1, CH3SEL = 0, CH4SEL = 1, CH5SEL = 0, CH6SEL = 1, CH7SEL = 0
(f) LDOK = 1, CH0SEL = 1, CH1SEL = 1, CH2SEL = 1, CH3SEL = 1, CH4SEL = 1, CH5SEL = 1, CH6SEL = 1, CH7SEL = 1
Figure 26-246. Loading points for intermediate load
After enabling the loading points, the LDOK bit must be set for the load to occur. In this
case, the load occurs at the next enabled loading point according to the following
conditions:
Table 26-249. Conditions for loads occurring at the next enabled loading point
When a new value was written
To the MOD register
Then
The MOD register is updated with its write buffer value.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
487
Functional description
Table 26-249. Conditions for loads occurring at the next enabled loading point (continued)
When a new value was written
To the CNTIN register and CNTINC = 1
Then
The CNTIN register is updated with its write buffer value.
To the C(n)V register and SYNCENm = 1 – where m indicates The C(n)V register is updated with its write buffer value.
the pair channels (n) and (n+1)
To the C(n+1)V register and SYNCENm = 1 – where m
indicates the pair channels (n) and (n+1)
•
•
•
•
The C(n+1)V register is updated with its write buffer value.
NOTE
If ELSjB and ELSjA bits are different from zero, then the
channel (j) output signal is generated according to the
configured output mode. If ELSjB and ELSjA bits are zero,
then the generated signal is not available on channel (j)
output.
If CHjIE = 1, then the channel (j) interrupt is generated
when the channel (j) match occurs.
At the intermediate load neither the channels outputs nor
the FTM counter are changed. Software must set the
intermediate load at a safe point in time.
The intermediate load feature must be used only in
Combine mode.
26.4.26 Global time base (GTB)
The global time base (GTB) is a FTM function that allows the synchronization of
multiple FTM modules on a chip. The following figure shows an example of the GTB
feature used to synchronize two FTM modules. In this case, the FTM A and B channels
can behave as if just one FTM module was used, that is, a global time base.
FTM module A
FTM module B
FTM counter
GTBEEN bit
FTM counter
enable logic
enable
gtb_in
gtb_in
example glue logic
gtb_out
GTBEOUT bit
gtb_out
Figure 26-247. Global time base (GTB) block diagram
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
488
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
The GTB functionality is implemented by the GTBEEN and GTBEOUT bits in the
CONF register, the input signal gtb_in, and the output signal gtb_out. The GTBEEN bit
enables gtb_in to control the FTM counter enable signal:
• If GTBEEN = 0, each one of FTM modules works independently according to their
configured mode.
• If GTBEEN = 1, the FTM counter update is enabled only when gtb_in is 1.
In the configuration described in the preceding figure, FTM modules A and B have their
FTM counters enabled if at least one of the gtb_out signals from one of the FTM modules
is 1. There are several possible configurations for the interconnection of the gtb_in and
gtb_out signals, represented by the example glue logic shown in the figure. Note that
these configurations are chip-dependent and implemented outside of the FTM modules.
See the chip configuration details for the chip's specific implementation.
NOTE
• In order to use the GTB signals to synchronize the FTM
counter of different FTM modules, the configuration of
each FTM module should guarantee that its FTM counter
starts counting as soon as the gtb_in signal is 1.
• The GTB feature does not provide continuous
synchronization of FTM counters, meaning that the FTM
counters may lose synchronization during FTM operation.
The GTB feature only allows the FTM counters to start
their operation synchronously.
26.4.26.1 Enabling the global time base (GTB)
To enable the GTB feature, follow these steps for each participating FTM module:
1. Stop the FTM counter: Write 00b to SC[CLKS].
2. Program the FTM to the intended configuration. The FTM counter mode needs to be
consistent across all participating modules.
3. Write 1 to CONF[GTBEEN] and write 0 to CONF[GTBEOUT] at the same time.
4. Select the intended FTM counter clock source in SC[CLKS]. The clock source needs
to be consistent across all participating modules.
5. Reset the FTM counter: Write any value to the CNT register.
To initiate the GTB feature in the configuration described in the preceding figure, write 1
to CONF[GTBEOUT] in the FTM module used as the time base.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
489
Reset overview
26.5 Reset overview
The FTM is reset whenever any chip reset occurs.
When the FTM exits from reset:
• the FTM counter and the prescaler counter are zero and are stopped (CLKS[1:0] =
00b);
• the timer overflow interrupt is zero, see Timer Overflow Interrupt;
• the channels interrupts are zero, see Channel (n) Interrupt;
• the fault interrupt is zero, see Fault Interrupt;
• the channels are in input capture mode, see Input Capture mode;
• the channels outputs are zero;
• the channels pins are not controlled by FTM (ELS(n)B:ELS(n)A = 0:0) (See the table
in the description of CnSC register).
The following figure shows the FTM behavior after the reset. At the reset (item 1), the
FTM counter is disabled (see the description of the CLKS field in the Status and Control
register), its value is updated to zero and the pins are not controlled by FTM (See the
table in the description of CnSC register).
After the reset, the FTM should be configurated (item 2). It is necessary to define the
FTM counter mode, the FTM counting limits (MOD and CNTIN registers value), the
channels mode and CnV registers value according to the channels mode.
Thus, it is recommended to write any value to CNT register (item 3). This write updates
the FTM counter with the CNTIN register value and the channels output with its initial
value (except for channels in output compare mode) (Counter reset).
The next step is to select the FTM counter clock by the CLKS[1:0] bits (item 4). It is
important to highlight that the pins are only controlled by FTM when CLKS[1:0] bits are
different from zero (See the table in the description of CnSC register).
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
490
Freescale Semiconductor, Inc.
Chapter 26 FlexTimer Module (FTM)
(1) FTM reset
FTM counter
CLKS[1:0]
(3) write any value
to CNT register
XXXX
0x0000
XX
00
(4) write 1 to SC[CLKS]
0x0010
0x0011 0x0012 0x0013 0x0014 0x0015 0x0016 0x0017 0x0018 . . .
01
channel (n) output
(2) FTM configuration
channel (n) pin is controlled by FTM
NOTES:
– CNTIN = 0x0010
– Channel (n) is in low-true combine mode with CNTIN < C(n)V < C(n+1)V < MOD
– C(n)V = 0x0015
Figure 26-248. FTM behavior after reset when the channel (n) is in Combine mode
The following figure shows an example when the channel (n) is in Output Compare mode
and the channel (n) output is toggled when there is a match. In the Output Compare
mode, the channel output is not updated to its initial value when there is a write to CNT
register (item 3). In this case, use the software output control (Software output control) or
the initialization (Initialization) to update the channel output to the selected value (item
4).
(4) use of software output control or initialization
to update the channel output to the zero
(1) FTM reset
FTM counter
CLKS[1:0]
(3) write any value
to CNT register
XXXX
0x0000
XX
00
(5) write 1 to SC[CLKS]
0x0010
0x0011 0x0012 0x0013 0x0014 0x0015 0x0016 0x0017 . . .
01
channel (n) output
(2) FTM configuration
channel (n) pin is controlled by FTM
NOTES:
– CNTIN = 0x0010
– Channel (n) is in output compare and the channel (n) output is toggled when there is a match
– C(n)V = 0x0014
Figure 26-249. FTM behavior after reset when the channel (n) is in Output Compare
mode
26.6 FTM Interrupts
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
491
FTM Interrupts
26.6.1 Timer Overflow Interrupt
The timer overflow interrupt is generated when (TOIE = 1) and (TOF = 1).
26.6.2 Channel (n) Interrupt
The channel (n) interrupt is generated when (CHnIE = 1) and (CHnF = 1).
26.6.3 Fault Interrupt
The fault interrupt is generated when (FAULTIE = 1) and (FAULTF = 1).
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
492
Freescale Semiconductor, Inc.
Chapter 27
Pulse Width Timer (PWT)
27.1 Introduction
27.1.1 Features
The pulse width timer (PWT) includes the following features:
• Automatic measurement of pulse width with 16-bit resolution
• Separate positive and negative pulse width measurements
• Programmable triggering edge for starting measurement
• Programmable measuring time between successive alternating edges, rising edges or
falling edges
• Programmable prescaler from clock input as 16-bit counter time base
• Two selectable clock sources—bus clock and alternative clock
• Four selectable pulse inputs
• Programmable interrupt generation upon pulse width value updated and counter
overflow
27.1.2 Modes of operation
The following table describes the operation of the PWT module in various modes.
Modes
Description
Run
When enabled, the pulse width timer module is active.
Wait
When enabled, the pulse width timer module is active and can perform the waking up function if the
corresponding interrupt is enabled.
Stop
The pulse width timer module is halted when entering stop and the register contents and operating
status is preserved. If stop exits with reset then the module resets. If stop exits with another source,
the module resumes operation based on module status upon exit.
Active background
Upon entering Debug mode, the PWT suspends all counting and pulse edge detection until the
microcontroller returns to normal user operating mode. Counting and edge detection resume from
the suspended value when normal user operating mode returns as long as the PWTSR bit (PWT
software reset) is not written to 1 and the PWT module is still enabled.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
493
Introduction
27.1.3 Block diagram
The following is the block diagram of the pulse width timer module (PWT).
PWT_CLK
Clock Pre-scaler(CLKPRE)
/2
/2
/2
/2
/2
/2
/2
SYNC
ALT_CLK
PRE[2:0]
PCLKS
PWTCLK
PWTEN
PWTSR
16 bit free running counter
PWTOV
16
PWT_R1[PPW]
PWT_R2[NPW]
PWTIN0
PWTIN1
PWTIN2
PWTIN3
Overflow
Interrupt
Edge Detect and Capture Control Logic
PWTIN
PWTRDY
PINSEL[1:0]
POVIE
EDGE[1:0]
PWTIE
PINEN0
Data
Interrupt
PINEN2
PINEN3
Decode
PINEN1
PRDYIE
Figure 27-1. Pulse width timer (PWT) block diagram
NOTE
The PWT_CLK depends on the Chip input clock. For this chip
it is TIMER_CLK.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
494
Freescale Semiconductor, Inc.
Chapter 27 Pulse Width Timer (PWT)
27.2 PWT signal description
Table 27-2. PWT signal description
Signal
I/O
Pullup
Description
PWTIN[3:0]
I
No
Pulse Inputs
ALTCLK
I
No
Alternative clock source for the counter
27.2.1 PWTIN[3:0] - Pulse Width Timer Capture Inputs
The input signals are pulse capture inputs which can come from internal or external
sources. The PWT input is selected by PINSEL[1:0] to be routed to the pulse width timer.
If the input comes from external source and is selected as the PWT input, the input port is
enabled for PWT function by PINSEL[1:0] automatically. The minimum pulse width to
be measured is 1 PWTCLK cycle, any pulse narrower than this value is ignored by PWT
module. The PWTCLK cycle time depends on the PWT clock source selection and
prescaler rate setting.
27.2.2 ALTCLK- Alternative Clock Source for Counter
The PWT has an alternative clock input ALTCLK which can be selected as the clock
source of the counter when R1[PCLKS] is set. The ALTCLK input must be synchronized
by the bus clock. Variations in duty cycle and clock jitter must also be accommodated so
that the ALTCLK signal must not exceed one-fourth of the bus frequency. The ALTCLK
pin can be shared with a general-purpose port pin. See the Pins and Connections chapter
for the pin location and priority of this function.
27.3 Memory Map and Register Descriptions
PWT memory map
Absolute
address
(hex)
Register name
Width
Access
(in bits)
Reset value
Section/
page
4003_3000
Pulse Width Timer Register 1 (PWT_R1)
32
R/W
0000_0000h
27.3.1/496
4003_3004
Pulse Width Timer Register 2 (PWT_R2)
32
R
0000_0000h
27.3.2/498
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
495
Memory Map and Register Descriptions
27.3.1 Pulse Width Timer Register 1 (PWT_R1)
This register defines the general control and status bits for the PWT. It also contains the
Positive Pulse Width contents.
Address: 4003_3000h base + 0h offset = 4003_3000h
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
PPW
R
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
0
0
PWTRDY
PWTOV
W
0
0
0
0
0
0
PWTSR
POVIE
PRE
PRDYIE
EDGE
PWTIE
PINSEL
PWTEN
PCLKS
R
W
Reset
0
0
0
0
0
0
0
0
0
0
PWT_R1 field descriptions
Field
Description
31–16
PPW
Positive Pulse Width
15
PCLKS
PWT Clock Source Selection
Captured positive pulse width value. It is suggested to use half-word (16-bit) or word (32-bit) to read out
this value.
Controls the selection of clock source for the PWT counter.
0
1
14–13
PINSEL
TIMER_CLK is selected as the clock source of PWT counter.
Alternative clock is selected as the clock source of PWT counter.
PWT Pulse Inputs Selection
Enables the corresponding PWT input port, if this PWT input comes from an external source.
00
01
PWTIN[0] is enabled.
PWTIN[1] is enabled.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
496
Freescale Semiconductor, Inc.
Chapter 27 Pulse Width Timer (PWT)
PWT_R1 field descriptions (continued)
Field
Description
10
11
12–11
EDGE
PWT Input Edge Sensitivity
Selects which edge triggers the pulse width measurement and which edges trigger the capture. If user
needs to change the trigger and capture mode by changing the value of EDGE[1:0], a PWT software reset
is required after changing the EDGE[1:0] value. Clearing PWTEN and then setting it has the same effect.
00
01
10
11
10–8
PRE
Selects the value by which the clock is divided to clock the PWT counter.
Enables/disables the PWT module. To avoid unexpected behavior, do not change any PWT configurations
as long as PWTEN is set.
Enables the PWT module to generate an interrupt.
Disables the PWT to generate interrupt.
Enables the PWT to generate interrupt.
PWT Pulse Width Data Ready Interrupt Enable
Enables/disables the PWT to generate an interrupt when PWTRDY is set as long as PWTIE is set.
0
1
4
POVIE
The PWT is disabled.
The PWT is enabled.
PWT Module Interrupt Enable
0
1
5
PRDYIE
Clock divided by 1.
Clock divided by 2.
Clock divided by 4.
Clock divided by 8.
Clock divided by 16.
Clock divided by 32.
Clock divided by 64.
Clock divided by 128.
PWT Module Enable
0
1
6
PWTIE
The first falling-edge starts the pulse width measurement, and on all the subsequent falling edges,
the pulse width is captured.
The first rising edge starts the pulse width measurement, and on all the subsequent rising and falling
edges, the pulse width is captured.
The first falling edge starts the pulse width measurement, and on all the subsequent rising and falling
edges, the pulse width is captured.
The first-rising edge starts the pulse width measurement, and on all the subsequent rising edges, the
pulse width is captured.
PWT Clock Prescaler (CLKPRE) Setting
000
001
010
011
100
101
110
111
7
PWTEN
PWTIN[2] enabled.
PWTIN[3] enabled.
Disable PWT to generate interrupt when PWTRDY is set.
Enable PWT to generate interrupt when PWTRDY is set.
PWT Counter Overflow Interrupt Enable
Enables/disables the PWT to generate an interrupt when PWTOV is set due to PWT counter overflow.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
497
Memory Map and Register Descriptions
PWT_R1 field descriptions (continued)
Field
Description
0
1
3
PWTSR
Disable PWT to generate interrupt when PWTOV is set.
Enable PWT to generate interrupt when PWTOV is set.
PWT Soft Reset
Performs a soft reset to the PWT. This field always reads as 0.
0
1
No action taken.
Writing 1 to this field will perform soft reset to PWT.
2
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
1
PWTRDY
PWT Pulse Width Valid
Indicates that the PWT Pulse Width register(s) has been updated and is ready to be read. This field is
cleared by reading PWTRDY and then writing 0 to PWTRDY bit when PWTRDY is set. Writing 1 to this
field has no effect. PWTRDY setting is associated with the EDGE[1:0] bits.
0
1
0
PWTOV
PWT pulse width register(s) is not up-to-date.
PWT pulse width register(s) has been updated.
PWT Counter Overflow
Indicates that the PWT counter has run from 0x0000_0xFFFF to 0x0000_0x0000. This field is cleared by
writing 0 to PWTOV when PWTOV is set. Writing 1 to this field has no effect. If another overflow occurs
when this field is being cleared, the clearing fails.
0
1
PWT counter no overflow.
PWT counter runs from 0xFFFF to 0x0000.
27.3.2 Pulse Width Timer Register 2 (PWT_R2)
This register contains the Negative Pulse Width contents and the 16-bit free running
counter contents.
Address: 4003_3000h base + 4h offset = 4003_3004h
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
PWTC
R
8
7
6
5
4
3
2
1
0
0
0
0
0
0
0
0
NPW
W
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
PWT_R2 field descriptions
Field
31–16
PWTC
NPW
Description
PWT Counter. It is suggested to use half-word (16-bit) or word (32-bit) to read out this value.
Negative Pulse Width. It is suggested to use half-word (16-bit) or word (32-bit) to read out this value.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
498
Freescale Semiconductor, Inc.
Chapter 27 Pulse Width Timer (PWT)
27.4 Functional Description
27.4.1 PWT Counter and PWT Clock Prescaler
The pulse width timer (PWT) measures duration of a pulse or the period of a signal input
to the PWTIN by a 16-bit free running counter (PWT_R2[PWTC]). There is a clock
prescaler (CLKPRE) in PWT module that provides the frequency divided clock to
PWT_R2[PWTC]. The clock prescaler can select clock input from bus clock and
alternative clock by PWT_R1[PCKLS].
The PWT counter uses the frequency divided clock from CLKPRE for counter
advancing. The frequency of prescaler is programmable as the clock frequency divided
by 1, 2, 4, 8, 16, 32, 64, 128 (depending on the setting of PRE[2:0]).
As soon as the PWT counter is enabled, it starts counting using the selected and divided
clock source; the counter is cleared without loading to the registers when the first valid
edge (trigger edge) is detected. If no valid trigger edge is detected for a long time, it is
possible for the counter to overflow. When 16-bit free running counter is running, any
edge to be measured after the trigger edge causes the value of PWT_R2[PWTC] to be
uploaded to the appropriate pulse width registers. At the same time, PWT_R2[PWTC]
will be reset to 0x0000 and the clock prescaler output will also be reset together.
PWT_R2[PWTC] will then start advancing again with the input clock. If the
PWT_R2[PWTC] runs from 0xFFFF to 0x0000, the PWTOV bit is set.
27.4.2 Edge detection and capture control
The edge detection and capture control part detects measurement trigger edges and
controls when and which pulse width register(s) will be updated.
Based on the setting of EDGE[1:0], the edge detection logic determines the starting and
ending edge of the pulse width to be measured on PWTIN, and the registers fields to be
updated. See Edge detection and capture control for details.
The PWTIN can be selected from one of four sources by configuring PINSEL[1:0].
It must be noted that inside the edge detection and capture logic, the system slave clock is
used for PWT to sample and synchronize the PWTIN pulse, therefore the minimal
PWTIN pulse width is determined by this slave clock frequency. For example, if this
clock frequency is 50 MHz, the minimal PWTIN pulse width must be longer than 20
ns(the period of 50 MHz), otherwise, PWT won't be able to capture this pulse and the
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
499
Functional Description
counter would overflow. See the chip configuration chapters to check the slave clock
frequency to PWT. Also, if there isn't any valid edge of the PWTIN width for a long
time, the PWT counter would overflow as well.
When EDGE[1:0] is 00, the first falling edge is the trigger edge from which the pulse
width begins to be measured. The counter value is uploaded to PWT_R1[PPW] upon
each of the subsequent falling edges. When EDGE[1:0] is 11, the first rising edge is the
trigger edge from which the pulse width begins to be measured. The counter value is
uploaded to PWT_R2[NPW] upon each successive rising-edge. In these two cases, the
period of PWTIN is measured.
When EDGE[1:0] is 01, the first rising edge is the trigger edge. The pulse width begins to
be measured from this edge. PWT_R1[PPW] is uploaded upon each of the subsequent
falling edges. PWT_R2[NPW] is uploaded upon each successive rising edge. When
EDGE[1:0] is 10, the first falling edge is the trigger edge from which the pulse width is
measured. PWT_R2[NPW] is uploaded on each successive rising edge and
PWT_R1[PPW] is uploaded on each successive falling edge. In these two cases, the
positive pulse and negative pulse are measured separately and the positive pulse width is
uploaded into PWT_R1[PPW]. The negative pulse width is uploaded into
PWT_R2[NPW].
The following figure illustrates the trigger edge detection and pulse width registers
update of PWT.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
500
Freescale Semiconductor, Inc.
Chapter 27 Pulse Width Timer (PWT)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Reset
PWTEN
Counter starts to count up
as soon as PWTR1[PWTEN] is set
PWTIN
Clear the pre-counter.
Trigger to measure and start counting up from 0.
Upload counter to PWTR1[PPW]
EDGE=00
Clear the pre-counter.
Trigger to measure and start counting up from 0.
Upload counter
to PWTR1[PPW]
EDGE=01
Clear the pre-counter.
Trigger to measure and start counting up from 0.
Upload counter
to PWTR1[PPW]
Upload counter
to PWTR2[NPW]
EDGE=10
Upload counter
to PWTR2[NPW]
EDGE=11
Clear the pre-counter.
Trigger to measure and start counting up from 0.
Upload counter
to PWTR2[NPW]
Figure 27-4. Trigger edge detection and pulse width registers update
PWT_R1[PWTRDY] indicates that the data can be read in PWT_R1[PPW] and/or
PWT_R2[NPW], based on the setting of EDGE[1:0].
• When EDGE[1:0] is 00, PWT_R1[PWTRDY] is set whenever PWT_R1[PPW] is
updated.
• When EDGE[1:0] is 11, PWT_R1[PWTRDY] is set whenever PWT_R2[NPW] is
updated.
• When EDGE[1:0] is 01, PWT_R1[PWTRDY] is set whenever PWTxPPH:L is
updated, followed by PWT_R2[NPW]'s update.
• When EDGE[1:0] is 10, PWT_R1[PWTRDY] is set whenever PWT_R2[NPW] is
updated, followed by PWT_R1[PPW]'s update.
When PWT_R1[PWTRDY] is set, the updated pulse width register(s) transfers the data
to corresponding 16-bit read buffer(s). The read value of pulse width registers actually
comes from the corresponding read buffers, whenever the chip is in normal run mode or
Debug mode. Reading followed by writing 0 to PWT_R1[PWTRDY] flag clears this
field. Until PWT_R1[PWTRDY] is cleared, the 16-bit read buffer(s) cannot be updated.
But this does not affect the upload of pulse width registers from the PWT counter.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
501
Functional Description
If another pulse measurement is completed and the pulse width registers are updated, the
clearing of the PWT_R1[PWTRDY] flag fails, that is, PWT_R1[PWTRDY] will still be
set, but the 16-bit read buffer(s) will be updated again as long as the action is cleared..
The user should complete the pulse width data reading before clearing
PWT_R1[PWTRDY] to avoid missing data. This mechanism assures that the second
pulse measurement will not be lost in case the MCU does not have enough time to read
the first one ready for read. The mechanism is automatically restarted by an MCU reset ,
writing 1 to PWT_R1[PWTSR] or writing a 0 to PWT_R1[PWTEN] followed by writing
a 1 to it.
The following figure illustrates the buffering mechanism of pulse width register:
PWTIN
CPU BUS
PWTRDY
Clear PWTRDY
Read/write
Logic
PPW
edge detect and capture logic
Read buffer upload control
Buffer of PPW
Read Data
16-bit Counter
NPW
Buffer of NPW
EDGE[1:0]
Figure 27-5. Buffering mechanism of Pulse Width register
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
502
Freescale Semiconductor, Inc.
Chapter 27 Pulse Width Timer (PWT)
When PWT completes any pulse width measurement, a signal is generated to reset
PWT_R2[CNTC] and the clock prescaler output after the data has been uploaded to the
pulse width registers. To assure that there is no missing count, PWT_R2[CNTC] and the
clock prescaler output are reset in a bus clock cycle after the completion of a pulse width
measurement.
27.5 Reset
27.5.1 General
27.5.2 Description of reset operation
PWT soft reset is built into PWT as a mechanism used to reset/restart the pulse width
timer. The PWT soft reset is triggered by writing 1 to PWT_R1[PWTSR]. (This field
always reads 0). Unlike reset by the CPU, the PWT reset does not restore everything in
the PWT to its reset state. The following steps can be used to describe the reset operation.
1. The PWT counter is set to 0x0000.
2. The 16-bit buffer of PWT counter is reset.
3. The PWT clock prescaler output is reset.
4. The edge detection logic is reset.
5. The capture logic is reset and the latching mechanism of pulse width registers is also
restarted.
6. PWT_R1[PPW] and PWT_R2[NPW] are set to 0x0000.
7. PWT_R1[PWTOV] and PWT_R1[PWTRDY] are set to 0.
8. All other PWT register settings are not changed.
Writing a 0 to PWT_R1[PWTEN] also has the above effects except that the reset state
will be held until PWT_R1[PWTEN] is set to 1.
27.6 Interrupts
27.6.1 Description of interrupt operation
The other major component of the PWT is the interrupts control logic. When
PWT_R1[PWTOV] and PWT_R1[POVIE] are set, a PWT overflow interrupt can be
generated. When PWT_R1[PWTRDY] bit and PWT_R1[PRDYIE] are set, a pulse width
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
503
Interrupts
data ready interrupt can be generated. PWT_R1[PWTIE] controls the interrupt generation
of the PWT module. The functionality of the PWT is not affected while the interrupt is
being generated.
27.6.2 Application examples
BUSCLK
PWTCLK
PWTCNT
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 0
counter read result: 23 pwtclk
actual pulse width: 23 pwtclk + err
PWTIN
counter read result: 22 pwtclk
actual pulse width: 22 pwtclk + err
(err < 1 pwtclk + 1 bus clock)
Figure 27-6. Example at PWTCLK is Bus Clock divided by 1
BUSCLK
PWTCLK
PWTCNT
PWTIN
0
1 2 3
4 5
6
7
8 9 10 11 0
counter read result: 11 pwtclk
actual pulse width: 11 pwtclk + err
1 2 3
4 5
6
8 9 1011 0
7
counter read result: 11 pwtclk
actual pulse width: 11 pwtclk + err
(err < 1 pwtclk + 1 bus clock)
Figure 27-7. Example at PWTCLK is Bus Clock divided by 2
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
504
Freescale Semiconductor, Inc.
Chapter 27 Pulse Width Timer (PWT)
BUSCLK
PWTCLK
PWTCNT
0
1
PWTIN
3
2
5
4
counter read result: 5 pwtclk
actual pulse width: 5 pwtclk + err
0
1
3
2
5
4
0
counter read result: 5 pwtclk
actual pulse width: 5 pwtclk + err
(err < 1 pwtclk + 1 bus clock)
Figure 27-8. Example at PWTCLK is Bus Clock divided by 4
BUSCLK
PWTCLK
0
PWTCNT
PWTIN
1
counter read result: 2 pwtclk
actual pulse width: 2 pwtclk + err
2
0
1
2
counter read result: 2 pwtclk
actual pulse width: 2 pwtclk + err
(err < 1 pwtclk + 1 bus clock)
Figure 27-9. Example at PWTCLK is Bus Clock divided by 8
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
505
Interrupts
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
506
Freescale Semiconductor, Inc.
Chapter 28
Periodic Interrupt Timer (PIT)
28.1 Introduction
NOTE
For the chip-specific implementation details of this module's
instances, see the chip configuration information.
The PIT module is an array of timers that can be used to raise interrupts and triggers.
28.1.1 Block diagram
The following figure shows the block diagram of the PIT module.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
507
Signal description
PIT
Peripheral bus
PIT
registers
load_value
Timer 1
Interrupts
Triggers
Timer n
Peripheral
bus clock
Figure 28-1. Block diagram of the PIT
NOTE
See the chip configuration details for the number of PIT
channels used in this MCU.
28.1.2 Features
The main features of this block are:
• Ability of timers to generate trigger pulses
• Ability of timers to generate interrupts
• Maskable interrupts
• Independent timeout periods for each timer
28.2 Signal description
The PIT module has no external pins.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
508
Freescale Semiconductor, Inc.
Chapter 28 Periodic Interrupt Timer (PIT)
28.3 Memory map/register description
This section provides a detailed description of all registers accessible in the PIT module.
• Reserved registers will read as 0, writes will have no effect.
• See the chip configuration details for the number of PIT channels used in this MCU.
PIT memory map
Absolute
address
(hex)
Width
Access
(in bits)
Register name
Reset value
Section/
page
4003_7000
PIT Module Control Register (PIT_MCR)
32
R/W
0000_0006h
28.3.1/509
4003_7100
Timer Load Value Register (PIT_LDVAL0)
32
R/W
0000_0000h
28.3.2/510
4003_7104
Current Timer Value Register (PIT_CVAL0)
32
R
0000_0000h
28.3.3/511
4003_7108
Timer Control Register (PIT_TCTRL0)
32
R/W
0000_0000h
28.3.4/511
4003_710C
Timer Flag Register (PIT_TFLG0)
32
R/W
0000_0000h
28.3.5/512
4003_7110
Timer Load Value Register (PIT_LDVAL1)
32
R/W
0000_0000h
28.3.2/510
4003_7114
Current Timer Value Register (PIT_CVAL1)
32
R
0000_0000h
28.3.3/511
4003_7118
Timer Control Register (PIT_TCTRL1)
32
R/W
0000_0000h
28.3.4/511
4003_711C
Timer Flag Register (PIT_TFLG1)
32
R/W
0000_0000h
28.3.5/512
28.3.1 PIT Module Control Register (PIT_MCR)
This register enables or disables the PIT timer clocks and controls the timers when the
PIT enters the Debug mode.
Address: 4003_7000h base + 0h offset = 4003_7000h
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
0
0
0
0
0
0
0
0
0
R
W
Reset
0
0
0
0
0
0
0
0
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
509
Memory map/register description
14
13
12
11
10
9
8
7
6
5
4
3
2
0
R
1
0
MDIS
FRZ
1
0
Reserved
15
Bit
W
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
1
PIT_MCR field descriptions
Field
Description
31–3
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
2
Reserved
This field is reserved.
1
MDIS
Module Disable - (PIT section)
Disables the standard timers. This field must be enabled before any other setup is done.
0
1
0
FRZ
Clock for standard PIT timers is enabled.
Clock for standard PIT timers is disabled.
Freeze
Allows the timers to be stopped when the device enters the Debug mode.
0
1
Timers continue to run in Debug mode.
Timers are stopped in Debug mode.
28.3.2 Timer Load Value Register (PIT_LDVALn)
These registers select the timeout period for the timer interrupts.
Address: 4003_7000h base + 100h offset + (16d × i), where i=0d to 1d
Bit
R
W
31
Reset
0
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
TSV
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
PIT_LDVALn field descriptions
Field
TSV
Description
Timer Start Value
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
510
Freescale Semiconductor, Inc.
Chapter 28 Periodic Interrupt Timer (PIT)
PIT_LDVALn field descriptions (continued)
Field
Description
Sets the timer start value. The timer will count down until it reaches 0, then it will generate an interrupt and
load this register value again. Writing a new value to this register will not restart the timer; instead the
value will be loaded after the timer expires. To abort the current cycle and start a timer period with the new
value, the timer must be disabled and enabled again.
28.3.3 Current Timer Value Register (PIT_CVALn)
These registers indicate the current timer position.
Address: 4003_7000h base + 104h offset + (16d × i), where i=0d to 1d
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
TVL
R
W
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
PIT_CVALn field descriptions
Field
Description
TVL
Current Timer Value
Represents the current timer value, if the timer is enabled.
NOTE:
• If the timer is disabled, do not use this field as its value is unreliable.
• The timer uses a downcounter. The timer values are frozen in Debug mode if MCR[FRZ] is
set.
28.3.4 Timer Control Register (PIT_TCTRLn)
These registers contain the control bits for each timer.
Address: 4003_7000h base + 108h offset + (16d × i), where i=0d to 1d
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
0
R
W
Reset
0
0
0
0
0
0
Bit
15
14
13
12
11
10
0
0
0
0
0
0
0
0
0
0
9
8
7
6
5
4
3
2
1
0
CHN
TIE
TEN
0
0
0
0
R
W
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
511
Memory map/register description
PIT_TCTRLn field descriptions
Field
Description
31–3
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
2
CHN
Chain Mode
When activated, Timer n-1 needs to expire before timer n can decrement by 1.
Timer 0 cannot be chained.
0
1
1
TIE
Timer is not chained.
Timer is chained to previous timer. For example, for Channel 2, if this field is set, Timer 2 is chained to
Timer 1.
Timer Interrupt Enable
When an interrupt is pending, or, TFLGn[TIF] is set, enabling the interrupt will immediately cause an
interrupt event. To avoid this, the associated TFLGn[TIF] must be cleared first.
0
1
0
TEN
Interrupt requests from Timer n are disabled.
Interrupt will be requested whenever TIF is set.
Timer Enable
Enables or disables the timer.
0
1
Timer n is disabled.
Timer n is enabled.
28.3.5 Timer Flag Register (PIT_TFLGn)
These registers hold the PIT interrupt flags.
Address: 4003_7000h base + 10Ch offset + (16d × i), where i=0d to 1d
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
0
R
W
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
0
R
TIF
w1c
W
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
PIT_TFLGn field descriptions
Field
31–1
Reserved
Description
This field is reserved.
This read-only field is reserved and always has the value 0.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
512
Freescale Semiconductor, Inc.
Chapter 28 Periodic Interrupt Timer (PIT)
PIT_TFLGn field descriptions (continued)
Field
0
TIF
Description
Timer Interrupt Flag
Sets to 1 at the end of the timer period. Writing 1 to this flag clears it. Writing 0 has no effect. If enabled,
or, when TCTRLn[TIE] = 1, TIF causes an interrupt request.
0
1
Timeout has not yet occurred.
Timeout has occurred.
28.4 Functional description
This section provides the functional description of the module.
28.4.1 General operation
This section gives detailed information on the internal operation of the module. Each
timer can be used to generate trigger pulses and interrupts. Each interrupt is available on
a separate interrupt line.
28.4.1.1 Timers
The timers generate triggers at periodic intervals, when enabled. The timers load the start
values as specified in their LDVAL registers, count down to 0 and then load the
respective start value again. Each time a timer reaches 0, it will generate a trigger pulse
and set the interrupt flag.
All interrupts can be enabled or masked by setting TCTRLn[TIE]. A new interrupt can be
generated only after the previous one is cleared.
If desired, the current counter value of the timer can be read via the CVAL registers.
The counter period can be restarted, by first disabling, and then enabling the timer with
TCTRLn[TEN]. See the following figure.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
513
Functional description
Re-enable
timer
Disable
timer
Timer enabled
Start value = p1
Trigger
event
p1
p1
p1
p1
Figure 28-15. Stopping and starting a timer
The counter period of a running timer can be modified, by first disabling the timer,
setting a new load value, and then enabling the timer again. See the following figure.
Timer enabled
Start value = p1
Disable timer,
Set new load value
Trigger
event
Re-enable
timer
p2
p1
p2
p2
p1
Figure 28-16. Modifying running timer period
It is also possible to change the counter period without restarting the timer by writing
LDVAL with the new load value. This value will then be loaded after the next trigger
event. See the following figure.
Timer enabled
Start value = p1
New start
Value p2 set
Trigger
event
p1
p1
p1
p2
p2
Figure 28-17. Dynamically setting a new load value
28.4.1.2 Debug mode
In Debug mode, the timers will be frozen based on MCR[FRZ]. This is intended to aid
software development, allowing the developer to halt the processor, investigate the
current state of the system, for example, the timer values, and then continue the
operation.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
514
Freescale Semiconductor, Inc.
Chapter 28 Periodic Interrupt Timer (PIT)
28.4.2 Interrupts
All the timers support interrupt generation. See the MCU specification for related vector
addresses and priorities.
Timer interrupts can be enabled by setting TCTRLn[TIE]. TFLGn[TIF] are set to 1 when
a timeout occurs on the associated timer, and are cleared to 0 by writing a 1 to the
corresponding TFLGn[TIF].
28.4.3 Chained timers
When a timer has chain mode enabled, it will only count after the previous timer has
expired. So if timer n-1 has counted down to 0, counter n will decrement the value by
one. This allows to chain some of the timers together to form a longer timer. The first
timer (timer 0) cannot be chained to any other timer.
28.5 Initialization and application information
In the example configuration:
• The PIT clock has a frequency of 50 MHz.
• Timer 1 creates an interrupt every 5.12 ms.
• Timer 3 creates a trigger event every 30 ms.
The PIT module must be activated by writing a 0 to MCR[MDIS].
The 50 MHz clock frequency equates to a clock period of 20 ns. Timer 1 needs to trigger
every 5.12 ms/20 ns = 256,000 cycles and Timer 3 every 30 ms/20 ns = 1,500,000 cycles.
The value for the LDVAL register trigger is calculated as:
LDVAL trigger = (period / clock period) -1
This means LDVAL1 and LDVAL3 must be written with 0x0003E7FF and 0x0016E35F
respectively.
The interrupt for Timer 1 is enabled by setting TCTRL1[TIE]. The timer is started by
writing 1 to TCTRL1[TEN].
Timer 3 shall be used only for triggering. Therefore, Timer 3 is started by writing a 1 to
TCTRL3[TEN]. TCTRL3[TIE] stays at 0.
The following example code matches the described setup:
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
515
Example configuration for chained timers
// turn on PIT
PIT_MCR = 0x00;
// Timer 1
PIT_LDVAL1 = 0x0003E7FF; // setup timer 1 for 256000 cycles
PIT_TCTRL1 = TIE; // enable Timer 1 interrupts
PIT_TCTRL1 |= TEN; // start Timer 1
// Timer 3
PIT_LDVAL3 = 0x0016E35F; // setup timer 3 for 1500000 cycles
PIT_TCTRL3 |= TEN; // start Timer 3
28.6 Example configuration for chained timers
In the example configuration:
• The PIT clock has a frequency of 100 MHz.
• Timers 1 and 2 are available.
• An interrupt shall be raised every 1 hour.
The PIT module needs to be activated by writing a 0 to MCR[MDIS].
The 100 MHz clock frequency equates to a clock period of 10 ns, so the PIT needs to
count for 6000 million cycles, which is more than a single timer can do. So, Timer 1 is
set up to trigger every 6 s (600 million cycles). Timer 2 is chained to Timer 1 and
programmed to trigger 10 times.
The value for the LDVAL register trigger is calculated as number of cycles-1, so
LDVAL1 receives the value 0x23C345FF and LDVAL2 receives the value 0x00000009.
The interrupt for Timer 2 is enabled by setting TCTRL2[TIE], the Chain mode is
activated by setting TCTRL2[CHN], and the timer is started by writing a 1 to
TCTRL2[TEN]. TCTRL1[TEN] needs to be set, and TCTRL1[CHN] and TCTRL1[TIE]
are cleared.
The following example code matches the described setup:
// turn on PIT
PIT_MCR = 0x00;
// Timer 2
PIT_LDVAL2
PIT_TCTRL2
PIT_TCTRL2
PIT_TCTRL2
= 0x00000009; //
= TIE; // enable
|= CHN; // chain
|= TEN; // start
setup
Timer
Timer
Timer
Timer 2 for 10 counts
2 interrupt
2 to Timer 1
2
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
516
Freescale Semiconductor, Inc.
Chapter 28 Periodic Interrupt Timer (PIT)
// Timer 1
PIT_LDVAL1 = 0x23C345FF; // setup Timer 1 for 600 000 000 cycles
PIT_TCTRL1 = TEN; // start Timer 1
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
517
Example configuration for chained timers
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
518
Freescale Semiconductor, Inc.
Chapter 29
Real-Time Counter (RTC)
29.1 Introduction
The real-time counter (RTC) consists of one 16-bit counter, one 16-bit comparator,
several binary-based and decimal-based prescaler dividers, three clock sources, one
programmable periodic interrupt, and one programmable external toggle pulse output.
This module can be used for time-of-day, calendar or any task scheduling functions. It
can also serve as a cyclic wake-up from low-power modes, Stop and Wait without the
need of external components.
29.2 Features
Features of the RTC module include:
• 16-bit up-counter
• 16-bit modulo match limit
• Software controllable periodic interrupt on match
• Software selectable clock sources for input to prescaler with programmable 16 bit
prescaler
• OSC 32.768KHz nominal.
• LPO (~1 kHz)
• Bus clock
• Internal reference clock (32 kHz)
29.2.1 Modes of operation
This section defines the RTC operation in Stop, Wait, and Background Debug modes.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
519
External signal description
29.2.1.1 Wait mode
The RTC continues to run in Wait mode if enabled before executing the WAIT
instruction. Therefore, the RTC can be used to bring the MCU out of Wait mode if the
real-time interrupt is enabled. For lowest possible current consumption, the RTC must be
stopped by software if not needed as an interrupt source during Wait mode.
29.2.1.2 Stop modes
The RTC continues to run in Stop mode if the RTC is enabled before executing the STOP
instruction. Therefore, the RTC can be used to bring the MCU out of stop modes with no
external components, if the real-time interrupt is enabled.
29.2.2 Block diagram
The block diagram for the RTC module is shown in the following figure.
RTCMOD
16-bit modulo
16-bit latch
16-bit modulo
1
16-bit comparator
EXT CLK
LPO CLK
BUS CLK
IRC CLK
CLOCK
DIVIDER
RTIF
D Q
RTC
INTERRUPT
REQUEST
R
16-bit counter
RTIE
D Q
Q
RTCLKS
RTCPS
RTCCNT
Write 1 to RTIF
OUTPUT
TOGLE
RTCO
Figure 29-1. Real-time counter (RTC) block diagram
29.3 External signal description
RTCO is the output of RTC. After MCU reset, the RTC_SC[RTCO] is set to high. When
the counter overflows, the output is toggled.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
520
Freescale Semiconductor, Inc.
Chapter 29 Real-Time Counter (RTC)
29.4 Register definition
The RTC includes a status and control register, a 16-bit counter register, and a 16-bit
modulo register.
RTC memory map
Absolute
address
(hex)
Width
Access
(in bits)
Register name
Reset value
Section/
page
4003_D000
RTC Status and Control Register (RTC_SC)
32
R/W
0000_0000h
29.4.1/521
4003_D004
RTC Modulo Register (RTC_MOD)
32
R/W
0000_0000h
29.4.2/523
4003_D008
RTC Counter Register (RTC_CNT)
32
R
0000_0000h
29.4.3/523
29.4.1 RTC Status and Control Register (RTC_SC)
RTC_SC contains the real-time interrupt status flag (RTIF), and the toggle output enable
bit (RTCO).
Address: 4003_D000h base + 0h offset = 4003_D000h
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
0
R
W
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
0
0
0
RTCLKS
RTCPS
RTIF
RTIE
0
0
W
Reset
0
0
0
0
0
0
0
0
0
0
RTCO
0
R
0
0
0
RTC_SC field descriptions
Field
Description
31–16
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
15–14
RTCLKS
Real-Time Clock Source Select
This read/write field selects the clock source input to the RTC prescaler. Changing the clock source clears
the prescaler and RTCCNT counters. Reset clears RTCLKS to 00.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
521
Register definition
RTC_SC field descriptions (continued)
Field
Description
00
01
10
11
13–11
Reserved
10–8
RTCPS
This field is reserved.
This read-only field is reserved and always has the value 0.
Real-Time Clock Prescaler Select
This read/write field selects binary-based or decimal-based divide-by values for the clock source.
Changing the prescaler value clears the prescaler and RTCCNT counters. Reset clears RTCPS to 000.
000
001
010
011
100
101
110
111
7
RTIF
This status bit indicates the RTC counter register reached the value in the RTC modulo register. Writing a
logic 0 has no effect. Writing a logic 1 clears the bit and the real-time interrupt request. Reset clears RTIF
to 0.
4
RTCO
This read/write bit enables real-time interrupts. If RTIE is set, then an interrupt is generated when RTIF is
set. Reset clears RTIE to 0.
Real-time interrupt requests are disabled. Use software polling.
Real-time interrupt requests are enabled.
This field is reserved.
This read-only field is reserved and always has the value 0.
Real-Time Counter Output
The read/write bit enables real-time to toggle output on pinout. If this bit is set, the RTCO pinout will be
toggled when RTC counter overflows.
0
1
Reserved
RTC counter has not reached the value in the RTC modulo register.
RTC counter has reached the value in the RTC modulo register.
Real-Time Interrupt Enable
0
1
5
Reserved
Off
If RTCLKS = x0, it is 1; if RTCLKS = x1, it is 128.
If RTCLKS = x0, it is 2; if RTCLKS = x1, it is 256.
If RTCLKS = x0, it is 4; if RTCLKS = x1, it is 512.
If RTCLKS = x0, it is 8; if RTCLKS = x1, it is 1024.
If RTCLKS = x0, it is 16; if RTCLKS = x1, it is 2048.
If RTCLKS = x0, it is 32; if RTCLKS = x1, it is 100.
If RTCLKS = x0, it is 64; if RTCLKS = x1, it is 1000.
Real-Time Interrupt Flag
0
1
6
RTIE
External clock source.
Real-time clock source is 1 kHz (LPOCLK).
Internal reference clock (ICSIRCLK).
Bus clock.
Real-time counter output disabled.
Real-time counter output enabled.
This field is reserved.
This read-only field is reserved and always has the value 0.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
522
Freescale Semiconductor, Inc.
Chapter 29 Real-Time Counter (RTC)
29.4.2 RTC Modulo Register (RTC_MOD)
RTC_MOD indicates the value of the 16-bit modulo value.
Address: 4003_D000h base + 4h offset = 4003_D004h
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
0
R
0
0
0
0
0
0
0
0
7
6
5
4
3
2
1
0
0
0
0
0
0
0
0
MOD
W
Reset
8
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
RTC_MOD field descriptions
Field
Description
31–16
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
MOD
RTC Modulo
This read/write field contains the modulo value used to reset the count to 0x0000 upon a compare match
and set SC[RTIF] status field. A value of 0x0000 sets SC[RTIF] on each rising-edge of the prescaler
output. Reset sets the modulo to 0x0000.
29.4.3 RTC Counter Register (RTC_CNT)
RTC_CNT indicates the read-only value of the current RTC count of the 16-bit counter.
Address: 4003_D000h base + 8h offset = 4003_D008h
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
0
R
8
7
6
5
4
3
2
1
0
0
0
0
0
0
0
0
CNT
W
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
RTC_CNT field descriptions
Field
31–16
Reserved
CNT
Description
This field is reserved.
This read-only field is reserved and always has the value 0.
RTC Count
This read-only field contains the current value of the 16-bit counter, read CNT[7:0] first and, then
CNT[15:8]. Writes have no effect to this register. Reset or writing different values to SC[RTCLKS] and
SC[RTCPS] clear the count to 0x0000.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
523
Functional description
29.5 Functional description
The RTC is composed of a main 16-bit up-counter with a 16-bit modulo register, a clock
source selector, and a prescaler block with binary-based and decimal-based selectable
values. The module also contains software selectable interrupt logic and toggle logic for
pinout.
After any MCU reset, the counter is stopped and reset to 0x0000, the modulus register is
set to 0x0000, and the prescaler is off. The external oscillator clock is selected as the
default clock source. To start the prescaler, write any value other than 0 to the Prescaler
Select field (RTC_SC[RTCPS]).
The clock sources are software selectable: the external oscillator (OSC), on-chip low
power oscillator (LPO), 32-kHz internal reference clock, and bus clock. The RTC Clock
Select field (RTC_SC[RTCLKS]) is used to select the desired clock source to the
prescaler dividers. If a different value is written to RTC_SC[RTCLKS], the prescaler and
CNT counters are reset to 0x00.
RTC_SC[RTCPS] and RTC_SC[RTCLKS] select the desired divide-by value. If a
different value is written to RTC_SC[RTCPS], the prescaler and RTCCNT counters are
reset to 0x00. The following table shows different prescaler period values.
Table 29-5. Prescaler period
RTCPS
32768Hz OSC clock
LPO clock (1 kHz)
source prescaler
source prescaler
period (RTCLKS = 00) period (RTCLKS = 01)
Internal reference
Bus clock (8 MHz)
clock (32.768 kHz)
source prescaler
source prescaler
period (RTCLKS = 11)
period (RTCLKS = 10)
000
Off
Off
Off
Off
001
30.5176 µs
128 ms
30.5176 µs
16 µs
010
61.0351 µs
256 ms
61.0351 µs
32 µs
011
122.0703 µs
512 ms
122.0703 µs
64 µs
100
244.1406 µs
1024 ms
244.1406 µs
128 µs
101
488.28125 µs
2048 ms
488.28125 µs
256 µs
110
976.5625 µs
100 ms
976.5625 µs
12.5 µs
111
1.9531 ms
1s
1.9531 ms
125 µs
The RTC Modulo register (RTC_MOD) allows the compare value to be set to any value
from 0x0000 to 0xFFFF. When the counter is active, the counter increments at the
selected rate until the count matches the modulo value. When these values match, the
counter resets to 0x0000 and continues counting. The Real-Time Interrupt Flag
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
524
Freescale Semiconductor, Inc.
Chapter 29 Real-Time Counter (RTC)
(RTC_SC[RTIF]) is set whenever a match occurs. The flag sets on the transition from the
modulo value to 0x0000. The modulo value written to RTC_MOD is latched until the
RTC counter overflows or RTC_SC[RTCPS] is selected nonzero.
The RTC allows for an interrupt to be generated whenever RTC_SC[RTIF] is set. To
enable the real-time interrupt, set the Real-Time Interrupt Enable field (RTC_SC[RTIE]).
RTC_SC[RTIF] is cleared by writing a 1 to RTC_SC[RTIF].
The RTC also allows an output to external pinout by toggling the level. RTC_SC[RTCO]
must be set to enable toggling external pinout. The level depends on the previous state of
the pinout when the counter overflows if this function is active.
29.5.1 RTC operation example
This section shows an example of the RTC operation as the counter reaches a matching
value from the modulo register.
OSC (32768Hz)
RTCLKS = 00b
RTC Clock
RTCPS = 001b
RTCCNT
RTCPS = 001b
32765
32766
32767
0
1
2
3
4
16-bit modulo
32767
32767
32767
32766
32766
32766
32766
32766
RTCMOD
32766
32766
32766
RTIF
RTCO
Figure 29-5. RTC counter overflow example
In the above example, the external clock source is selected. The prescaler is set to
RTC_SC[RTCPS] = 001b or passthrough. The actual modulo value used by 16-bit
comparator is 32767, when the modulo value in the RTC_MOD register is set to 32766.
When the counter, RTC_CNT, reaches the modulo value of 32767, the counter overflows
to 0x00 and continues counting. The modulo value is updated by fetching from
RTC_MOD register. The real-time interrupt flag, RTC_SC[RTIF], sets when the counter
value changes from 0x7FFF to 0x0000. The RTC_SC[RTCO] toggles as well when the
RTC_SC[RTIF] is set.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
525
Initialization/application information
29.6 Initialization/application information
This section provides example code to give some basic direction to a user on how to
initialize and configure the RTC module. The example software is implemented in C
language.
The example below shows how to implement time of day with the RTC using the OSC
clock source to achieve the lowest possible power consumption.
Example: 29.6.1 Software calendar implementation in RTC ISR
/* Initialize the elapsed time counters */
Seconds = 0;
Minutes = 0;
Hours = 0;
Days=0;
/* Configure RTC to interrupt every 1 second from OSC (32.768KHz) clock source */
RTC_MOD = 511; // overflow every 32 times
RTC_SC = RTC_SC_RTCPS_MASK; // external 32768 clock selected with 1/64 predivider.
RTC_SC = RTC_SC_RTIF_MASK | RTC_SC_RTIE_MASK; // interrupt cleared and enabled
/**********************************************************************
Function Name : RTC_ISR
Notes : Interrupt service routine for RTC module.
**********************************************************************/
void RTC_ISR(void)
{
/* Clears the interrupt flag, RTIF, and interrupt request */
RTC_SC |= RTC_SC_RTIF_MASK;
/* RTC interrupts every 1 Second */
Seconds++;
/* 60 seconds in a minute */
if (Seconds > 59)
{
Minutes++;
Seconds = 0;
}
/* 60 minutes in an hour */
if (Minutes > 59)
{
Hours++;
Minutes = 0;
}
/* 24 hours in a day */
if (Hours > 23)
{
Days ++;
Hours = 0;
}
}
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
526
Freescale Semiconductor, Inc.
Chapter 30
Serial Peripheral Interface (SPI)
30.1 Introduction
NOTE
For the chip-specific implementation details of this module's
instances, see the chip configuration information.
The serial peripheral interface (SPI) module provides for full-duplex, synchronous, serial
communication between the MCU and peripheral devices. These peripheral devices can
include other microcontrollers, analog-to-digital converters, shift registers, sensors, and
memories, among others.
The SPI runs at a baud rate up to the bus clock divided by two in master mode and up to
the bus clock divided by four in slave mode. Software can poll the status flags, or SPI
operation can be interrupt driven.
NOTE
For the actual maximum SPI baud rate, refer to the Chip
Configuration details and to the device’s Data Sheet.
The SPI also includes a hardware match feature for the receive data buffer.
30.1.1 Features
The SPI includes these distinctive features:
• Master mode or slave mode operation
• Full-duplex or single-wire bidirectional mode
• Programmable transmit bit rate
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
527
Introduction
• Double-buffered transmit and receive data register
• Serial clock phase and polarity options
• Slave select output
• Mode fault error flag with CPU interrupt capability
• Control of SPI operation during wait mode
• Selectable MSB-first or LSB-first shifting
• Receive data buffer hardware match feature
30.1.2 Modes of operation
The SPI functions in the following three modes.
• Run mode
This is the basic mode of operation.
• Wait mode
SPI operation in Wait mode is a configurable low power mode, controlled by the
SPISWAI bit located in the SPIx_C2 register. In Wait mode, if C2[SPISWAI] is
clear, the SPI operates like in Run mode. If C2[SPISWAI] is set, the SPI goes into a
power conservative state, with the SPI clock generation turned off. If the SPI is
configured as a master, any transmission in progress stops, but is resumed after CPU
enters Run mode. If the SPI is configured as a slave, reception and transmission of a
byte continues, so that the slave stays synchronized to the master.
• Stop mode
To reduce power consumption, the SPI is inactive in stop modes where the peripheral
bus clock is stopped but internal logic states are retained. If the SPI is configured as a
master, any transmission in progress stops, but is resumed after the CPU enters run
mode. If the SPI is configured as a slave, reception and transmission of a data
continues, so that the slave stays synchronized to the master.
The SPI is completely disabled in Stop modes where the peripheral bus clock is
stopped and internal logic states are not retained. When the CPU wakes from these
Stop modes, all SPI register content is reset.
Detailed descriptions of operating modes appear in Low-power mode options.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
528
Freescale Semiconductor, Inc.
Chapter 30 Serial Peripheral Interface (SPI)
30.1.3 Block diagrams
This section includes block diagrams showing SPI system connections, the internal
organization of the SPI module, and the SPI clock dividers that control the master mode
bit rate.
30.1.3.1 SPI system block diagram
The following figure shows the SPI modules of two MCUs connected in a master-slave
arrangement. The master device initiates all SPI data transfers. During a transfer, the
master shifts data out (on the MOSI pin) to the slave while simultaneously shifting data
in (on the MISO pin) from the slave. The transfer effectively exchanges the data that was
in the SPI shift registers of the two SPI systems. The SPSCK signal is a clock output
from the master and an input to the slave. The slave device must be selected by a low
level on the slave select input (SS pin). In this system, the master device has configured
its SS pin as an optional slave select output.
SLAVE
MASTER
MOSI
MOSI
SPI SHIFTER
8 BITS
SPI SHIFTER
MISO
SPSCK
CLOCK
GENERATOR
SS
MISO
8 BITS
SPSCK
SS
Figure 30-1. SPI system connections
30.1.3.2 SPI module block diagram
The following is a block diagram of the SPI module. The central element of the SPI is the
SPI shift register. Data is written to the double-buffered transmitter (write to SPIx_D) and
gets transferred to the SPI Shift Register at the start of a data transfer. After shifting in 8
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
529
Introduction
bits of data, the data is transferred into the double-buffered receiver where it can be read
from SPIx_D. Pin multiplexing logic controls connections between MCU pins and the
SPI module.
When the SPI is configured as a master, the clock output is routed to the SPSCK pin, the
shifter output is routed to MOSI, and the shifter input is routed from the MISO pin.
When the SPI is configured as a slave, the SPSCK pin is routed to the clock input of the
SPI, the shifter output is routed to MISO, and the shifter input is routed from the MOSI
pin.
In the external SPI system, simply connect all SPSCK pins to each other, all MISO pins
together, and all MOSI pins together. Peripheral devices often use slightly different
names for these pins.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
530
Freescale Semiconductor, Inc.
Chapter 30 Serial Peripheral Interface (SPI)
PIN CONTROL
M
SPE
MOSI
(MOMI)
S
Tx BUFFER (WRITE SPIxD)
ENABLE
SPI SYSTEM
M
SPI SHIFT REGISTER
SHIFT
OUT
SHIFT
IN
Rx BUFFER (READ SPIxD)
MISO
(SISO)
S
SPC0
BIDIROE
LSBFE
SHIFT
DIRECTION
Rx BUFFER Tx BUFFER
SHIFT
FULL
CLOCK
EMPTY
MASTER CLOCK
BUS RATE
CLOCK
MSTR
CLOCK
LOGIC
SPIBR
CLOCK GENERATOR
SLAVE CLOCK
MASTER/SLAVE
M
SPSCK
S
MASTER/
SLAVE
MODE SELECT
MODSSOE
MODE FAULT
DETECTION
SPRF
8-BIT COMPARATOR
SPIxM
SS
SPMF
SPMIE
SPTEF
SPTIE
MODF
SPIE
INTERRUPT
REQUEST
Figure 30-2. SPI module block diagram without FIFO
30.2 External signal description
The SPI optionally shares four port pins. The function of these pins depends on the
settings of SPI control bits. When the SPI is disabled (SPE = 0), these four pins revert to
other functions that are not controlled by the SPI (based on chip configuration).
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
531
External signal description
30.2.1 SPSCK — SPI Serial Clock
When the SPI is enabled as a slave, this pin is the serial clock input. When the SPI is
enabled as a master, this pin is the serial clock output.
30.2.2 MOSI — Master Data Out, Slave Data In
When the SPI is enabled as a master and SPI pin control zero (SPC0) is 0 (not
bidirectional mode), this pin is the serial data output. When the SPI is enabled as a slave
and SPC0 is 0, this pin is the serial data input. If SPC0 is 1 to select single-wire
bidirectional mode, and master mode is selected, this pin becomes the bidirectional data
I/O pin (MOMI). Also, the bidirectional mode output enable bit determines whether the
pin acts as an input (BIDIROE is 0) or an output (BIDIROE is 1). If SPC0 is 1 and slave
mode is selected, this pin is not used by the SPI and reverts to other functions (based on
chip configuration).
30.2.3 MISO — Master Data In, Slave Data Out
When the SPI is enabled as a master and SPI pin control zero (SPC0) is 0 (not
bidirectional mode), this pin is the serial data input. When the SPI is enabled as a slave
and SPC0 is 0, this pin is the serial data output. If SPC0 is 1 to select single-wire
bidirectional mode, and slave mode is selected, this pin becomes the bidirectional data I/
O pin (SISO), and the bidirectional mode output enable bit determines whether the pin
acts as an input (BIDIROE is 0) or an output (BIDIROE is 1). If SPC0 is 1 and master
mode is selected, this pin is not used by the SPI and reverts to other functions (based on
chip configuration).
30.2.4 SS — Slave Select
When the SPI is enabled as a slave, this pin is the low-true slave select input. When the
SPI is enabled as a master and mode fault enable is off (MODFEN is 0), this pin is not
used by the SPI and reverts to other functions (based on chip configuration). When the
SPI is enabled as a master and MODFEN is 1, the slave select output enable bit
determines whether this pin acts as the mode fault input (SSOE is 0) or as the slave select
output (SSOE is 1).
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
532
Freescale Semiconductor, Inc.
Chapter 30 Serial Peripheral Interface (SPI)
30.3 Memory map/register definition
The SPI has 8-bit registers to select SPI options, to control baud rate, to report SPI status,
to hold an SPI data match value, and for transmit/receive data.
SPI memory map
Address
offset (hex)
Absolute
address
(hex)
Width
Access
(in bits)
Register name
Reset value
Section/
page
0
4007_6000 SPI Control Register 1 (SPI0_C1)
8
R/W
04h
30.3.1/533
1
4007_6001 SPI Control Register 2 (SPI0_C2)
8
R/W
00h
30.3.2/535
2
4007_6002 SPI Baud Rate Register (SPI0_BR)
8
R/W
00h
30.3.3/536
3
4007_6003 SPI Status Register (SPI0_S)
8
R
20h
30.3.4/537
5
4007_6005 SPI Data Register (SPI0_D)
8
R/W
00h
30.3.5/538
7
4007_6007 SPI Match Register (SPI0_M)
8
R/W
00h
30.3.6/539
0
4007_7000 SPI Control Register 1 (SPI1_C1)
8
R/W
04h
30.3.1/533
1
4007_7001 SPI Control Register 2 (SPI1_C2)
8
R/W
00h
30.3.2/535
2
4007_7002 SPI Baud Rate Register (SPI1_BR)
8
R/W
00h
30.3.3/536
3
4007_7003 SPI Status Register (SPI1_S)
8
R
20h
30.3.4/537
5
4007_7005 SPI Data Register (SPI1_D)
8
R/W
00h
30.3.5/538
7
4007_7007 SPI Match Register (SPI1_M)
8
R/W
00h
30.3.6/539
30.3.1 SPI Control Register 1 (SPIx_C1)
This read/write register includes the SPI enable control, interrupt enables, and
configuration options.
Address: 4007_6000h base + 0h offset = 4007_6000h
Bit
Read
Write
Reset
7
6
5
4
3
2
1
0
SPIE
SPE
SPTIE
MSTR
CPOL
CPHA
SSOE
LSBFE
0
0
0
0
0
1
0
0
SPI0_C1 field descriptions
Field
7
SPIE
Description
SPI Interrupt Enable: for SPRF and MODF
Enables the interrupt for SPI receive buffer full (SPRF) and mode fault (MODF) events.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
533
Memory map/register definition
SPI0_C1 field descriptions (continued)
Field
Description
0
1
6
SPE
Enables the SPI system and dedicates the SPI port pins to SPI system functions. If SPE is cleared, the
SPI is disabled and forced into an idle state, and all status bits in the S register are reset.
This is the interrupt enable bit for SPI transmit buffer empty (SPTEF). An interrupt occurs when the SPI
transmit buffer is empty (SPTEF is set).
Interrupts from SPTEF inhibited (use polling)
When SPTEF is 1, hardware interrupt requested
Master/Slave Mode Select
Selects master or slave mode operation.
0
1
3
CPOL
SPI system inactive
SPI system enabled
SPI Transmit Interrupt Enable
0
1
4
MSTR
Request a hardware interrupt when SPRF or MODF is 1
SPI System Enable
0
1
5
SPTIE
Interrupts from SPRF and MODF are inhibited—use polling
SPI module configured as a slave SPI device
SPI module configured as a master SPI device
Clock Polarity
Selects an inverted or non-inverted SPI clock. To transmit data between SPI modules, the SPI modules
must have identical CPOL values.
This bit effectively places an inverter in series with the clock signal either from a master SPI device or to a
slave SPI device. Refer to the description of “SPI Clock Formats” for details.
0
1
2
CPHA
Clock Phase
Selects one of two clock formats for different kinds of synchronous serial peripheral devices. Refer to the
description of “SPI Clock Formats” for details.
0
1
1
SSOE
Active-high SPI clock (idles low)
Active-low SPI clock (idles high)
First edge on SPSCK occurs at the middle of the first cycle of a data transfer.
First edge on SPSCK occurs at the start of the first cycle of a data transfer.
Slave Select Output Enable
This bit is used in combination with the Mode Fault Enable (MODFEN) field in the C2 register and the
Master/Slave (MSTR) control bit to determine the function of the SS pin.
0
1
When C2[MODFEN] is 0: In master mode, SS pin function is general-purpose I/O (not SPI). In slave
mode, SS pin function is slave select input.
When C2[MODFEN] is 1: In master mode, SS pin function is SS input for mode fault. In slave mode,
SS pin function is slave select input.
When C2[MODFEN] is 0: In master mode, SS pin function is general-purpose I/O (not SPI). In slave
mode, SS pin function is slave select input.
When C2[MODFEN] is 1: In master mode, SS pin function is automatic SS output. In slave mode: SS
pin function is slave select input.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
534
Freescale Semiconductor, Inc.
Chapter 30 Serial Peripheral Interface (SPI)
SPI0_C1 field descriptions (continued)
Field
0
LSBFE
Description
LSB First (shifter direction)
This bit does not affect the position of the MSB and LSB in the data register. Reads and writes of the data
register always have the MSB in bit 7.
0
1
SPI serial data transfers start with the most significant bit.
SPI serial data transfers start with the least significant bit.
30.3.2 SPI Control Register 2 (SPIx_C2)
This read/write register is used to control optional features of the SPI system. Bit 6 is not
implemented and always reads 0.
Address: 4007_6000h base + 1h offset = 4007_6001h
Bit
Read
Write
Reset
7
6
5
4
3
2
1
0
SPMIE
Reserved
Reserved
MODFEN
BIDIROE
Reserved
SPISWAI
SPC0
0
0
0
0
0
0
0
0
SPI0_C2 field descriptions
Field
7
SPMIE
Description
SPI Match Interrupt Enable
This is the interrupt enable bit for the SPI receive data buffer hardware match (SPMF) function.
0
1
Interrupts from SPMF inhibited (use polling)
When SPMF is 1, requests a hardware interrupt
6
Reserved
This field is reserved.
Do not write to this reserved bit.
5
Reserved
This field is reserved.
Do not write to this reserved bit.
4
MODFEN
Master Mode-Fault Function Enable
When the SPI is configured for slave mode, this bit has no meaning or effect. (The SS pin is the slave
select input.) In master mode, this bit determines how the SS pin is used. For details, refer to the
description of the SSOE bit in the C1 register.
0
1
3
BIDIROE
Mode fault function disabled, master SS pin reverts to general-purpose I/O not controlled by SPI
Mode fault function enabled, master SS pin acts as the mode fault input or the slave select output
Bidirectional Mode Output Enable
When bidirectional mode is enabled because SPI pin control 0 (SPC0) is set to 1, BIDIROE determines
whether the SPI data output driver is enabled to the single bidirectional SPI I/O pin. Depending on whether
the SPI is configured as a master or a slave, it uses the MOSI (MOMI) or MISO (SISO) pin, respectively,
as the single SPI data I/O pin. When SPC0 is 0, BIDIROE has no meaning or effect.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
535
Memory map/register definition
SPI0_C2 field descriptions (continued)
Field
Description
0
1
Output driver disabled so SPI data I/O pin acts as an input
SPI I/O pin enabled as an output
2
Reserved
This field is reserved.
Do not write to this reserved bit.
1
SPISWAI
SPI Stop in Wait Mode
This bit is used for power conservation while the device is in Wait mode.
0
1
0
SPC0
SPI clocks continue to operate in Wait mode.
SPI clocks stop when the MCU enters Wait mode.
SPI Pin Control 0
Enables bidirectional pin configurations.
0
SPI uses separate pins for data input and data output (pin mode is normal).
In master mode of operation: MISO is master in and MOSI is master out.
1
In slave mode of operation: MISO is slave out and MOSI is slave in.
SPI configured for single-wire bidirectional operation (pin mode is bidirectional).
In master mode of operation: MISO is not used by SPI; MOSI is master in when BIDIROE is 0 or
master I/O when BIDIROE is 1.
In slave mode of operation: MISO is slave in when BIDIROE is 0 or slave I/O when BIDIROE is 1;
MOSI is not used by SPI.
30.3.3 SPI Baud Rate Register (SPIx_BR)
Use this register to set the prescaler and bit rate divisor for an SPI master. This register
may be read or written at any time.
Address: 4007_6000h base + 2h offset = 4007_6002h
Bit
7
Read
Write
Reset
0
0
6
5
4
3
2
SPPR[2:0]
0
0
1
0
0
0
SPR[3:0]
0
0
0
SPI0_BR field descriptions
Field
Description
7
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
6–4
SPPR[2:0]
SPI Baud Rate Prescale Divisor
This 3-bit field selects one of eight divisors for the SPI baud rate prescaler. The input to this prescaler is
the bus rate clock (BUSCLK). The output of this prescaler drives the input of the SPI baud rate divider.
Refer to the description of “SPI Baud Rate Generation” for details.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
536
Freescale Semiconductor, Inc.
Chapter 30 Serial Peripheral Interface (SPI)
SPI0_BR field descriptions (continued)
Field
Description
000
001
010
011
100
101
110
111
SPR[3:0]
Baud rate prescaler divisor is 1.
Baud rate prescaler divisor is 2.
Baud rate prescaler divisor is 3.
Baud rate prescaler divisor is 4.
Baud rate prescaler divisor is 5.
Baud rate prescaler divisor is 6.
Baud rate prescaler divisor is 7.
Baud rate prescaler divisor is 8.
SPI Baud Rate Divisor
This 4-bit field selects one of nine divisors for the SPI baud rate divider. The input to this divider comes
from the SPI baud rate prescaler. Refer to the description of “SPI Baud Rate Generation” for details.
0000
0001
0010
0011
0100
0101
0110
0111
1000
All others
Baud rate divisor is 2.
Baud rate divisor is 4.
Baud rate divisor is 8.
Baud rate divisor is 16.
Baud rate divisor is 32.
Baud rate divisor is 64.
Baud rate divisor is 128.
Baud rate divisor is 256.
Baud rate divisor is 512.
Reserved
30.3.4 SPI Status Register (SPIx_S)
This register contains read-only status bits. Writes have no meaning or effect.
NOTE
Bits 3 through 0 are not implemented and always read 0.
Address: 4007_6000h base + 3h offset = 4007_6003h
Bit
Read
7
6
5
4
SPRF
SPMF
SPTEF
MODF
0
0
1
0
3
2
1
0
0
0
0
Write
Reset
0
0
SPI0_S field descriptions
Field
7
SPRF
Description
SPI Read Buffer Full Flag
SPRF is set at the completion of an SPI transfer to indicate that received data may be read from the SPI
data (D) register. SPRF is cleared by reading SPRF while it is set and then reading the SPI data register.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
537
Memory map/register definition
SPI0_S field descriptions (continued)
Field
Description
0
1
6
SPMF
Data available in the receive data buffer
SPI Match Flag
SPMF is set after SPRF is 1 when the value in the receive data buffer matches the value in the M register.
To clear the flag, read SPMF when it is set and then write a 1 to it.
0
1
5
SPTEF
No data available in the receive data buffer
Value in the receive data buffer does not match the value in the M register
Value in the receive data buffer matches the value in the M register
SPI Transmit Buffer Empty Flag
This bit is set when the transmit data buffer is empty. SPTEF is cleared by reading the S register with
SPTEF set and then writing a data value to the transmit buffer at D. The S register must be read with
SPTEF set to 1 before writing data to the D register; otherwise, the D write is ignored. SPTEF is
automatically set when all data from the transmit buffer transfers into the transmit shift register. For an idle
SPI, data written to D is transferred to the shifter almost immediately so that SPTEF is set within two bus
cycles, allowing a second set of data to be queued into the transmit buffer. After completion of the transfer
of the data in the shift register, the queued data from the transmit buffer automatically moves to the shifter,
and SPTEF is set to indicate that room exists for new data in the transmit buffer. If no new data is waiting
in the transmit buffer, SPTEF simply remains set and no data moves from the buffer to the shifter.
If a transfer does not stop, the last data that was transmitted is sent out again.
0
1
4
MODF
SPI transmit buffer empty
Master Mode Fault Flag
MODF is set if the SPI is configured as a master and the slave select input goes low, indicating some
other SPI device is also configured as a master. The SS pin acts as a mode fault error input only when
C1[MSTR] is 1, C2[MODFEN] is 1, and C1[SSOE] is 0; otherwise, MODF will never be set. MODF is
cleared by reading MODF while it is 1 and then writing to the SPI Control Register 1 (C1).
0
1
Reserved
SPI transmit buffer not empty
No mode fault error
Mode fault error detected
This field is reserved.
This read-only field is reserved and always has the value 0.
30.3.5 SPI Data Register (SPIx_D)
This register is both the input and output register for SPI data. A write to the register
writes to the transmit data buffer, allowing data to be queued and transmitted.
When the SPI is configured as a master, data queued in the transmit data buffer is
transmitted immediately after the previous transmission has completed.
The SPTEF bit in the S register indicates when the transmit data buffer is ready to accept
new data. The S register must be read when S[SPTEF] is set before writing to the SPI
data register; otherwise, the write is ignored.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
538
Freescale Semiconductor, Inc.
Chapter 30 Serial Peripheral Interface (SPI)
Data may be read from the SPI data register any time after S[SPRF] is set and before
another transfer is finished. Failure to read the data out of the receive data buffer before a
new transfer ends causes a receive overrun condition, and the data from the new transfer
is lost. The new data is lost because the receive buffer still held the previous character
and was not ready to accept the new data. There is no indication for a receive overrun
condition, so the application system designer must ensure that previous data has been
read from the receive buffer before a new transfer is initiated.
Address: 4007_6000h base + 5h offset = 4007_6005h
Bit
Read
Write
Reset
7
6
5
4
3
2
1
0
0
0
0
0
Bits[7:0]
0
0
0
0
SPI0_D field descriptions
Field
Bits[7:0]
Description
Data (low byte)
30.3.6 SPI Match Register (SPIx_M)
This register contains the hardware compare value. When the value received in the SPI
receive data buffer equals this hardware compare value, the SPI Match Flag in the S
register (S[SPMF]) sets.
Address: 4007_6000h base + 7h offset = 4007_6007h
Bit
Read
Write
Reset
7
6
5
4
3
2
1
0
0
0
0
0
Bits[7:0]
0
0
0
0
SPI0_M field descriptions
Field
Bits[7:0]
Description
Hardware compare value (low byte)
30.4 Functional description
This section provides the functional description of the module.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
539
Functional description
30.4.1 General
The SPI system is enabled by setting the SPI enable (SPE) bit in SPI Control Register 1.
While C1[SPE] is set, the four associated SPI port pins are dedicated to the SPI function
as:
• Slave select (SS)
• Serial clock (SPSCK)
• Master out/slave in (MOSI)
• Master in/slave out (MISO)
An SPI transfer is initiated in the master SPI device by reading the SPI status register
(SPIx_S) when S[SPTEF] = 1 and then writing data to the transmit data buffer (write to
SPIxD ). When a transfer is complete, received data is moved into the receive data buffer.
The SPIxD register acts as the SPI receive data buffer for reads and as the SPI transmit
data buffer for writes.
The Clock Phase Control (CPHA) and Clock Polarity Control (CPOL) bits in the SPI
Control Register 1 (SPIx_C1) select one of four possible clock formats to be used by the
SPI system. The CPOL bit simply selects a non-inverted or inverted clock. C1[CPHA] is
used to accommodate two fundamentally different protocols by sampling data on odd
numbered SPSCK edges or on even numbered SPSCK edges.
The SPI can be configured to operate as a master or as a slave. When the MSTR bit in
SPI Control Register 1 is set, master mode is selected; when C1[MSTR] is clear, slave
mode is selected.
30.4.2 Master mode
The SPI operates in master mode when C1[MSTR] is set. Only a master SPI module can
initiate transmissions. A transmission begins by reading the SPIx_S register while
S[SPTEF] = 1 and writing to the master SPI data registers. If the shift register is empty,
the byte immediately transfers to the shift register. The data begins shifting out on the
MOSI pin under the control of the serial clock.
• SPSCK
• The SPR3, SPR2, SPR1, and SPR0 baud rate selection bits in conjunction with
the SPPR2, SPPR1, and SPPR0 baud rate preselection bits in the SPI Baud Rate
register control the baud rate generator and determine the speed of the
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
540
Freescale Semiconductor, Inc.
Chapter 30 Serial Peripheral Interface (SPI)
transmission. The SPSCK pin is the SPI clock output. Through the SPSCK pin,
the baud rate generator of the master controls the shift register of the slave
peripheral.
• MOSI, MISO pin
• In master mode, the function of the serial data output pin (MOSI) and the serial
data input pin (MISO) is determined by the SPC0 and BIDIROE control bits.
• SS pin
• If C2[MODFEN] and C1[SSOE] are set, the SS pin is configured as slave select
output. The SS output becomes low during each transmission and is high when
the SPI is in idle state. If C2[MODFEN] is set and C1[SSOE] is cleared, the SS
pin is configured as input for detecting mode fault error. If the SS input becomes
low this indicates a mode fault error where another master tries to drive the
MOSI and SPSCK lines. In this case, the SPI immediately switches to slave
mode by clearing C1[MSTR] and also disables the slave output buffer MISO (or
SISO in bidirectional mode). As a result, all outputs are disabled, and SPSCK,
MOSI and MISO are inputs. If a transmission is in progress when the mode fault
occurs, the transmission is aborted and the SPI is forced into idle state. This
mode fault error also sets the Mode Fault (MODF) flag in the SPI Status Register
(SPIx_S). If the SPI Interrupt Enable bit (SPIE) is set when S[ MODF] gets set,
then an SPI interrupt sequence is also requested. When a write to the SPI Data
Register in the master occurs, there is a half SPSCK-cycle delay. After the delay,
SPSCK is started within the master. The rest of the transfer operation differs
slightly, depending on the clock format specified by the SPI clock phase bit,
CPHA, in SPI Control Register 1 (see SPI clock formats).
Note
A change of C1[CPOL], C1[CPHA], C1[SSOE], C1[LSBFE],
C2[MODFEN], C2[SPC0], C2[BIDIROE] with C2[SPC0] set,
SPPR2-SPPR0 and SPR3-SPR0 in master mode abort a
transmission in progress and force the SPI into idle state. The
remote slave cannot detect this, therefore the master has to
ensure that the remote slave is set back to idle state.
30.4.3 Slave mode
The SPI operates in slave mode when the MSTR bit in SPI Control Register 1 is clear.
• SPSCK
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
541
Functional description
In slave mode, SPSCK is the SPI clock input from the master.
• MISO, MOSI pin
In slave mode, the function of the serial data output pin (MISO) and serial data input
pin (MOSI) is determined by the SPC0 bit and BIDIROE bit in SPI Control Register
2.
• SS pin
The SS pin is the slave select input. Before a data transmission occurs, the SS pin of
the slave SPI must be low. SS must remain low until the transmission is complete. If
SS goes high, the SPI is forced into an idle state.
The SS input also controls the serial data output pin. If SS is high (not selected), the
serial data output pin is high impedance. If SS is low, the first bit in the SPI Data
Register is driven out of the serial data output pin. Also, if the slave is not selected
(SS is high), then the SPSCK input is ignored and no internal shifting of the SPI shift
register occurs.
Although the SPI is capable of duplex operation, some SPI peripherals are capable of
only receiving SPI data in a slave mode. For these simpler devices, there is no serial
data out pin.
Note
When peripherals with duplex capability are used, take care not
to simultaneously enable two receivers whose serial outputs
drive the same system slave's serial data output line.
As long as no more than one slave device drives the system slave's serial data output line,
it is possible for several slaves to receive the same transmission from a master, although
the master would not receive return information from all of the receiving slaves.
If the CPHA bit in SPI Control Register 1 is clear, odd numbered edges on the SPSCK
input cause the data at the serial data input pin to be latched. Even numbered edges cause
the value previously latched from the serial data input pin to shift into the LSB or MSB
of the SPI shift register, depending on the LSBFE bit.
If C1[CPHA] is set, even numbered edges on the SPSCK input cause the data at the serial
data input pin to be latched. Odd numbered edges cause the value previously latched
from the serial data input pin to shift into the LSB or MSB of the SPI shift register,
depending on C1[LSBFE].
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
542
Freescale Semiconductor, Inc.
Chapter 30 Serial Peripheral Interface (SPI)
When C1[CPHA] is set, the first edge is used to get the first data bit onto the serial data
output pin. When C1[CPHA] is clear and the SS input is low (slave selected), the first bit
of the SPI data is driven out of the serial data output pin. After the eighth shift, the
transfer is considered complete and the received data is transferred into the SPI Data
register. To indicate transfer is complete, the SPRF flag in the SPI Status Register is set.
Note
A change of the bits C2[BIDIROE] with C2[SPC0] set,
C1[CPOL], C1[CPHA], C1[SSOE], C1[LSBFE],
C2[MODFEN], and C2[SPC0] in slave mode will corrupt a
transmission in progress and must be avoided.
30.4.4 SPI clock formats
To accommodate a wide variety of synchronous serial peripherals from different
manufacturers, the SPI system has a Clock Polarity (CPOL) bit and a Clock Phase
(CPHA) control bit in the Control Register 1 to select one of four clock formats for data
transfers. C1[CPOL] selectively inserts an inverter in series with the clock. C1[CPHA]
chooses between two different clock phase relationships between the clock and data.
The following figure shows the clock formats when CPHA = 1. At the top of the figure,
the eight bit times are shown for reference with bit 1 starting at the first SPSCK edge and
bit 8 ending one-half SPSCK cycle after the eighth SPSCK edge. The MSB first and LSB
first lines show the order of SPI data bits depending on the setting in LSBFE. Both
variations of SPSCK polarity are shown, but only one of these waveforms applies for a
specific transfer, depending on the value in C1[CPOL]. The SAMPLE IN waveform
applies to the MOSI input of a slave or the MISO input of a master. The MOSI waveform
applies to the MOSI output pin from a master and the MISO waveform applies to the
MISO output from a slave. The SS OUT waveform applies to the slave select output from
a master (provided C2[MODFEN] and C1[SSOE] = 1). The master SS output goes to
active low one-half SPSCK cycle before the start of the transfer and goes back high at the
end of the eighth bit time of the transfer. The SS IN waveform applies to the slave select
input of a slave.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
543
Functional description
BIT TIME #
(REFERENCE)
1
2
...
6
8
7
SPSCK
(CPOL = 0)
SPSCK
(CPOL = 1)
SAMPLE IN
(MISO OR MOSI)
MOSI
(MASTER OUT)
MSB FIRST
LSB FIRST
BIT 7
BIT 0
BIT 6
BIT 1
...
...
BIT 2
BIT 5
BIT 1
BIT 6
BIT 0
BIT 7
MISO
(SLAVE OUT)
SS OUT
(MASTER)
SS IN
(SLAVE)
Figure 30-21. SPI clock formats (CPHA = 1)
When C1[CPHA] = 1, the slave begins to drive its MISO output when SS goes to active
low, but the data is not defined until the first SPSCK edge. The first SPSCK edge shifts
the first bit of data from the shifter onto the MOSI output of the master and the MISO
output of the slave. The next SPSCK edge causes both the master and the slave to sample
the data bit values on their MISO and MOSI inputs, respectively. At the third SPSCK
edge, the SPI shifter shifts one bit position which shifts in the bit value that was just
sampled, and shifts the second data bit value out the other end of the shifter to the MOSI
and MISO outputs of the master and slave, respectively.
When C1[CPHA] = 1, the slave's SS input is not required to go to its inactive high level
between transfers. In this clock format, a back-to-back transmission can occur, as
follows:
1. A transmission is in progress.
2. A new data byte is written to the transmit buffer before the in-progress transmission
is complete.
3. When the in-progress transmission is complete, the new, ready data byte is
transmitted immediately.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
544
Freescale Semiconductor, Inc.
Chapter 30 Serial Peripheral Interface (SPI)
Between these two successive transmissions, no pause is inserted; the SS pin remains
low.
The following figure shows the clock formats when C1[CPHA] = 0. At the top of the
figure, the eight bit times are shown for reference with bit 1 starting as the slave is
selected (SS IN goes low), and bit 8 ends at the last SPSCK edge. The MSB first and
LSB first lines show the order of SPI data bits depending on the setting in LSBFE. Both
variations of SPSCK polarity are shown, but only one of these waveforms applies for a
specific transfer, depending on the value in CPOL. The SAMPLE IN waveform applies
to the MOSI input of a slave or the MISO input of a master. The MOSI waveform applies
to the MOSI output pin from a master and the MISO waveform applies to the MISO
output from a slave. The SS OUT waveform applies to the slave select output from a
master (provided C2[MODFEN] and C1[SSOE] = 1). The master SS output goes to
active low at the start of the first bit time of the transfer and goes back high one-half
SPSCK cycle after the end of the eighth bit time of the transfer. The SS IN waveform
applies to the slave select input of a slave.
BIT TIME #
(REFERENCE)
1
2
...
6
7
8
SPSCK
(CPOL = 0)
SPSCK
(CPOL = 1)
SAMPLE IN
(MISO OR MOSI)
MOSI
(MASTER OUT)
BIT 7
BIT 0
MSB FIRST
LSB FIRST
BIT 6
BIT 1
...
...
BIT 2
BIT 5
BIT 1
BIT 6
BIT 0
BIT 7
MISO
(SLAVE OUT)
SS OUT
(MASTER)
SS IN
(SLAVE)
Figure 30-22. SPI clock formats (CPHA = 0)
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
545
Functional description
When C1[CPHA] = 0, the slave begins to drive its MISO output with the first data bit
value (MSB or LSB depending on LSBFE) when SS goes to active low. The first SPSCK
edge causes both the master and the slave to sample the data bit values on their MISO
and MOSI inputs, respectively. At the second SPSCK edge, the SPI shifter shifts one bit
position which shifts in the bit value that was just sampled and shifts the second data bit
value out the other end of the shifter to the MOSI and MISO outputs of the master and
slave, respectively. When C1[CPHA] = 0, the slave's SS input must go to its inactive high
level between transfers.
30.4.5 SPI baud rate generation
As shown in the following figure, the clock source for the SPI baud rate generator is the
bus clock. The three prescale bits (SPPR2:SPPR1:SPPR0) choose a prescale divisor of 1,
2, 3, 4, 5, 6, 7, or 8. The three rate select bits (SPR3:SPR2:SPR1:SPR0) divide the output
of the prescaler stage by 2, 4, 8, 16, 32, 64, 128, 256, or 512 to get the internal SPI master
mode bit-rate clock.
The baud rate generator is activated only when the SPI is in the master mode and a serial
transfer is taking place. In the other cases, the divider is disabled to decrease IDD current.
The baud rate divisor equation is as follows (except those reserved combinations in the
SPI Baud Rate Divisor table).
BaudRateDivisor = (SPPR + 1) × 2(SPR
+ 1)
The baud rate can be calculated with the following equation:
BaudRate = BusClock / BaudRateDivisor
BUS
CLOCK
PRESCALER
BAUD RATE DIVIDER
DIVIDE BY
1, 2, 3, 4, 5, 6, 7, or 8
DIVIDE BY
2, 4, 8, 16, 32, 64, 128,
256, or 512
SPPR2:SPPR1:SPPR0
SPR3:SPR2:SPR1:SPR0
MASTER
SPI
BIT RATE
Figure 30-23. SPI baud rate generation
30.4.6 Special features
The following section describes the special features of SPI module.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
546
Freescale Semiconductor, Inc.
Chapter 30 Serial Peripheral Interface (SPI)
30.4.6.1 SS Output
The SS output feature automatically drives the SS pin low during transmission to select
external devices and drives the SS pin high during idle to deselect external devices. When
the SS output is selected, the SS output pin is connected to the SS input pin of the
external device.
The SS output is available only in master mode during normal SPI operation by asserting
C1[SSOE] and C2[MODFEN] as shown in the description of C1[SSOE].
The mode fault feature is disabled while SS output is enabled.
Note
Be careful when using the SS output feature in a multimaster
system because the mode fault feature is not available for
detecting system errors between masters.
30.4.6.2 Bidirectional mode (MOMI or SISO)
The bidirectional mode is selected when the SPC0 bit is set in SPI Control Register 2 (see
the following table). In this mode, the SPI uses only one serial data pin for the interface
with one or more external devices. C1[MSTR] decides which pin to use. The MOSI pin
becomes the serial data I/O (MOMI) pin for the master mode, and the MISO pin becomes
serial data I/O (SISO) pin for the slave mode. The MISO pin in master mode and MOSI
pin in slave mode are not used by the SPI.
Table 30-22. Normal Mode and Bidirectional Mode
When SPE = 1
Master Mode MSTR = 1
Serial Out
Normal Mode
Slave Mode MSTR = 0
MOSI
SPI
SPC0 = 0
Bidirectional Mode
SPC0 = 1
SPI
Serial In
MISO
Serial Out
Serial Out
MOMI
Serial In
SPI
Serial In
MOSI
Serial In
BIDIROE
SPI
MISO
BIDIROE
Serial Out
SISO
The direction of each serial I/O pin depends on C2[BIDIROE]. If the pin is configured as
an output, serial data from the shift register is driven out on the pin. The same pin is also
the serial input to the shift register.
The SPSCK is an output for the master mode and an input for the slave mode.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
547
Functional description
SS is the input or output for the master mode, and it is always the input for the slave
mode.
The bidirectional mode does not affect SPSCK and SS functions.
Note
In bidirectional master mode, with the mode fault feature
enabled, both data pins MISO and MOSI can be occupied by
the SPI, though MOSI is normally used for transmissions in
bidirectional mode and MISO is not used by the SPI. If a mode
fault occurs, the SPI is automatically switched to slave mode. In
this case, MISO becomes occupied by the SPI and MOSI is not
used. Consider this scenario if the MISO pin is used for another
purpose.
30.4.7 Error conditions
The SPI module has one error condition: the mode fault error.
30.4.7.1 Mode fault error
If the SS input becomes low while the SPI is configured as a master, it indicates a system
error where more than one master may be trying to drive the MOSI and SPSCK lines
simultaneously. This condition is not permitted in normal operation, and it sets the
MODF bit in the SPI status register automatically provided that C2[MODFEN] is set.
In the special case where the SPI is in master mode and C2[MODFEN] is cleared, the SS
pin is not used by the SPI. In this special case, the mode fault error function is inhibited
and MODF remains cleared. If the SPI system is configured as a slave, the SS pin is a
dedicated input pin. A mode fault error does not occur in slave mode.
If a mode fault error occurs, the SPI is switched to slave mode, with the exception that
the slave output buffer is disabled. So the SPSCK, MISO and MOSI pins are forced to be
high impedance inputs to avoid any possibility of conflict with another output driver. A
transmission in progress is aborted and the SPI is forced into idle state.
If the mode fault error occurs in the bidirectional mode for an SPI system configured in
master mode, the output enable of MOMI (MOSI in bidirectional mode) is cleared if it
was set. No mode fault error occurs in the bidirectional mode for the SPI system
configured in slave mode.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
548
Freescale Semiconductor, Inc.
Chapter 30 Serial Peripheral Interface (SPI)
The mode fault flag is cleared automatically by a read of the SPI Status Register (with
MODF set) followed by a write to SPI Control Register 1. If the mode fault flag is
cleared, the SPI becomes a normal master or slave again.
30.4.8 Low-power mode options
This section describes the low-power mode options.
30.4.8.1 SPI in Run mode
In Run mode, with the SPI system enable (SPE) bit in the SPI Control Register 1 clear,
the SPI system is in a low-power, disabled state. SPI registers can still be accessed, but
clocks to the core of this module are disabled.
30.4.8.2 SPI in Wait mode
SPI operation in Wait mode depends upon the state of the SPISWAI bit in SPI Control
Register 2.
• If C2[SPISWAI] is clear, the SPI operates normally when the CPU is in Wait mode.
• If C2[SPISWAI] is set, SPI clock generation ceases and the SPI module enters a
power conservation state when the CPU is in wait mode.
• If C2[SPISWAI] is set and the SPI is configured for master, any transmission
and reception in progress stops at Wait mode entry. The transmission and
reception resumes when the SPI exits Wait mode.
• If C2[SPISWAI] is set and the SPI is configured as a slave, any transmission and
reception in progress continues if the SPSCK continues to be driven from the
master. This keeps the slave synchronized to the master and the SPSCK.
If the master transmits data while the slave is in wait mode, the slave continues
to send data consistent with the operation mode at the start of wait mode (that is,
if the slave is currently sending its SPIx_D to the master, it continues to send the
same byte. Otherwise, if the slave is currently sending the last data received byte
from the master, it continues to send each previously received data from the
master byte).
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
549
Functional description
Note
Care must be taken when expecting data from a master while
the slave is in a Wait mode or a Stop mode where the peripheral
bus clock is stopped but internal logic states are retained. Even
though the shift register continues to operate, the rest of the SPI
is shut down (that is, an SPRF interrupt is not generated until an
exit from Stop or Wait mode). Also, the data from the shift
register is not copied into the SPIx_D registers until after the
slave SPI has exited Wait or Stop mode. An SPRF flag and
SPIx_D copy is only generated if Wait mode is entered or
exited during a transmission. If the slave enters Wait mode in
idle mode and exits Wait mode in idle mode, neither an SPRF
nor a SPIx_D copy occurs.
30.4.8.3 SPI in Stop mode
Operation in a Stop mode where the peripheral bus clock is stopped but internal logic
states are retained depends on the SPI system. The Stop mode does not depend on
C2[SPISWAI]. Upon entry to this type of stop mode, the SPI module clock is disabled
(held high or low).
• If the SPI is in master mode and exchanging data when the CPU enters the Stop
mode, the transmission is frozen until the CPU exits stop mode. After the exit from
stop mode, data to and from the external SPI is exchanged correctly.
• In slave mode, the SPI remains synchronized with the master.
The SPI is completely disabled in a stop mode where the peripheral bus clock is stopped
and internal logic states are not retained. After an exit from this type of stop mode, all
registers are reset to their default values, and the SPI module must be reinitialized.
30.4.9 Reset
The reset values of registers and signals are described in the Memory Map and Register
Descriptions content, which details the registers and their bitfields.
• If a data transmission occurs in slave mode after a reset without a write to SPIx_D,
the transmission consists of "garbage" or the data last received from the master
before the reset.
• Reading from SPIx_D after reset always returns zeros.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
550
Freescale Semiconductor, Inc.
Chapter 30 Serial Peripheral Interface (SPI)
30.4.10 Interrupts
The SPI originates interrupt requests only when the SPI is enabled (the SPE bit in the
SPIx_C1 register is set). The following is a description of how the SPI makes a request
and how the MCU should acknowledge that request. The interrupt vector offset and
interrupt priority are chip dependent.
Four flag bits, three interrupt mask bits, and one interrupt vector are associated with the
SPI system. The SPI interrupt enable mask (SPIE) enables interrupts from the SPI
receiver full flag (SPRF) and mode fault flag (MODF). The SPI transmit interrupt enable
mask (SPTIE) enables interrupts from the SPI transmit buffer empty flag (SPTEF). The
SPI match interrupt enable mask bit (SPIMIE) enables interrupts from the SPI match flag
(SPMF). When one of the flag bits is set, and the associated interrupt mask bit is set, a
hardware interrupt request is sent to the CPU. If the interrupt mask bits are cleared,
software can poll the associated flag bits instead of using interrupts. The SPI interrupt
service routine (ISR) should check the flag bits to determine which event caused the
interrupt. The service routine should also clear the flag bit(s) before returning from the
ISR (usually near the beginning of the ISR).
30.4.10.1 MODF
MODF occurs when the master detects an error on the SS pin. The master SPI must be
configured for the MODF feature (see the description of the C1[SSOE] bit). Once MODF
is set, the current transfer is aborted and the master (MSTR) bit in the SPIx_C1 register
resets to 0.
The MODF interrupt is reflected in the status register's MODF flag. Clearing the flag also
clears the interrupt. This interrupt stays active while the MODF flag is set. MODF has an
automatic clearing process that is described in the SPI Status Register.
30.4.10.2 SPRF
SPRF occurs when new data has been received and copied to the SPI receive data buffer.
After SPRF is set, it does not clear until it is serviced. SPRF has an automatic clearing
process that is described in the SPI Status Register details. If the SPRF is not serviced
before the end of the next transfer (that is, SPRF remains active throughout another
transfer), the subsequent transfers are ignored and no new data is copied into the Data
register.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
551
Initialization/application information
30.4.10.3 SPTEF
SPTEF occurs when the SPI transmit buffer is ready to accept new data.
After SPTEF is set, it does not clear until it is serviced. SPTEF has an automatic clearing
process that is described in the SPI Status Register details.
30.4.10.4 SPMF
SPMF occurs when the data in the receive data buffer is equal to the data in the SPI
Match Register.
30.4.10.5 Asynchronous interrupt in low-power modes
When the CPU is in Wait mode or Stop mode and the SPI module receives a
transmission, the SPI module can generate an asynchronous interrupt to wake the CPU
from the low power mode. The module generates the asynchronous interrupt only when
all of the following conditions apply:
1. C1[SPIE] is set to 1.
2. The CPU is in Wait mode—in which case C2[SPISWAI] must be 1—or in Stop
mode where the peripheral bus clock is stopped but internal logic states are retained.
3. The SPI module is in slave mode.
4. The received transmission ends.
After the interrupt wakes the CPU and the peripheral bus clock is active again, the SPI
module copies the received data from the shifter into the Data register and generates flags
signals. During the wakeup phase, a continuous transmission from a master would
destroy the first received data.
30.5 Initialization/application information
This section discusses an example of how to initialize and use the SPI.
30.5.1 Initialization sequence
Before the SPI module can be used for communication, an initialization procedure must
be carried out, as follows:
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
552
Freescale Semiconductor, Inc.
Chapter 30 Serial Peripheral Interface (SPI)
1. Update the Control Register 1 (SPIx_C1) to enable the SPI and to control interrupt
enables. This register also sets the SPI as master or slave, determines clock phase and
polarity, and configures the main SPI options.
2. Update the Control Register 2 (SPIx_C2) to enable additional SPI functions such as
the SPI match interrupt feature, the master mode-fault function, and bidirectional
mode output as well as to control and other optional features.
3. Update the Baud Rate Register (SPIx_BR) to set the prescaler and bit rate divisor for
an SPI master.
4. Update the Hardware Match Register (SPIx_M) with the value to be compared to the
receive data register for triggering an interrupt if hardware match interrupts are
enabled.
5. In the master, read SPIx_S while S[SPTEF] = 1, and then write to the transmit data
register (SPIx_D) to begin transfer.
30.5.2 Pseudo-Code Example
In this example, the SPI module is set up for master mode with only hardware match
interrupts enabled. The SPI runs at a maximum baud rate of bus clock divided by 2.
Clock phase and polarity are set for an active-high SPI clock where the first edge on
SPSCK occurs at the start of the first cycle of a data transfer.
SPIx_C1=0x54(%01010100)
Bit 7
SPIE
=
0
Disables receive and mode fault interrupts
Bit 6
SPE
=
1
Enables the SPI system
Bit 5
SPTIE
=
0
Disables SPI transmit interrupts
Bit 4
MSTR
=
1
Sets the SPI module as a master SPI device
Bit 3
CPOL
=
0
Configures SPI clock as active-high
Bit 2
CPHA
=
1
First edge on SPSCK at start of first data transfer cycle
Bit 1
SSOE
=
0
Determines SS pin function when mode fault enabled
Bit 0
LSBFE
=
0
SPI serial data transfers start with most significant bit
SPMIE
SPIx_C2 = 0x80(%10000000)
Bit 7
=
1
SPI hardware match interrupt enabled
Bit 6
=
0
Unimplemented
Bit 5
=
0
Reserved
Bit 4
MODFEN
=
0
Disables mode fault function
Bit 3
BIDIROE
=
0
SPI data I/O pin acts as input
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
553
Initialization/application information
SPIx_C2 = 0x80(%10000000)
Bit 2
=
0
Reserved
Bit 1
SPISWAI
=
0
SPI clocks operate in wait mode
Bit 0
SPC0
=
0
uses separate pins for data input and output
Bit 7
=
0
Reserved
Bit 6:4
=
000
Sets prescale divisor to 1
Bit 3:0
=
0000 Sets baud rate divisor to 2
SPIx_BR = 0x00(%00000000)
SPIx_S = 0x00(%00000000)
Bit 7
SPRF
=
0
Flag is set when receive data buffer is full
Bit 6
SPMF
=
0
Flag is set when SPIx_M = receive data buffer
Bit 5
SPTEF
=
0
Flag is set when transmit data buffer is empty
Bit 4
MODF
=
0
Mode fault flag for master mode
=
0
Reserved
Bit 3:0
SPIx_M = 0xXX
Holds bits 0–7 of the hardware match buffer.
SPIx_D = 0xxx
Holds bits 0–7 of the data to be transmitted by the transmit buffer and received by the receive buffer.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
554
Freescale Semiconductor, Inc.
Chapter 30 Serial Peripheral Interface (SPI)
RESET
INITIALIZE SPI
SPIxC1 = 0x54
SPIxC2 = 0x80
SPIxBR = 0x00
YES
SPTEF = 1
?
NO
YES
WRITE TO
SPIxD
SPRF = 1
?
NO
YES
READ
SPIxD
SPMF = 1
?
NO
YES
READ SPMF WHILE SET
TO CLEAR FLAG,
THEN WRITE A 1 TO IT
CONTINUE
Figure 30-24. Initialization Flowchart Example for SPI Master Device
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
555
Initialization/application information
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
556
Freescale Semiconductor, Inc.
Chapter 31
Inter-Integrated Circuit (I2C)
31.1 Introduction
NOTE
For the chip-specific implementation details of this module's
instances, see the chip configuration information.
The inter-integrated circuit (I2C, I2C, or IIC) module provides a method of
communication between a number of devices.
The interface is designed to operate up to 100 kbit/s with maximum bus loading and
timing. The I2C device is capable of operating at higher baud rates, up to a maximum of
clock/20, with reduced bus loading. The maximum communication length and the
number of devices that can be connected are limited by a maximum bus capacitance of
400 pF. The I2C module also complies with the System Management Bus (SMBus)
Specification, version 2.
31.1.1 Features
The I2C module has the following features:
•
•
•
•
•
•
•
•
•
•
Compatible with The I2C-Bus Specification
Multimaster operation
Software programmable for one of 64 different serial clock frequencies
Software-selectable acknowledge bit
Interrupt-driven byte-by-byte data transfer
Arbitration-lost interrupt with automatic mode switching from master to slave
Calling address identification interrupt
START and STOP signal generation and detection
Repeated START signal generation and detection
Acknowledge bit generation and detection
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
557
Introduction
•
•
•
•
•
•
•
Bus busy detection
General call recognition
10-bit address extension
Support for System Management Bus (SMBus) Specification, version 2
Programmable glitch input filter
Low power mode wakeup on slave address match
Range slave address support
31.1.2 Modes of operation
The I2C module's operation in various low power modes is as follows:
• Run mode: This is the basic mode of operation. To conserve power in this mode,
disable the module.
• Wait mode: The module continues to operate when the core is in Wait mode and can
provide a wakeup interrupt.
• Stop mode: The module is inactive in Stop mode for reduced power consumption,
except that address matching is enabled in Stop mode. The STOP instruction does
not affect the I2C module's register states.
31.1.3 Block diagram
The following figure is a functional block diagram of the I2C module.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
558
Freescale Semiconductor, Inc.
Chapter 31 Inter-Integrated Circuit (I2C)
Module Enable
Address
Write/Read
Interrupt
ADDR_DECODE
DATA_MUX
CTRL_REG
DATA_REG
FREQ_REG ADDR_REG STATUS_REG
Input
Sync
START
STOP
Arbitration
Control
Clock
Control
In/Out
Data
Shift
Register
Address
Compare
SCL
SDA
Figure 31-1. I2C Functional block diagram
31.2 I2C signal descriptions
The signal properties of I2C are shown in the table found here.
Table 31-1. I2C signal descriptions
Signal
Description
I/O
SCL
Bidirectional serial clock line of the I2C system.
I/O
SDA
Bidirectional serial data line of the I2C system.
I/O
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
559
Memory map/register definition
31.3 Memory map/register definition
This section describes in detail all I2C registers accessible to the end user.
I2C memory map
Absolute
address
(hex)
Register name
Width
Access
(in bits)
Reset value
Section/
page
4006_6000
I2C Address Register 1 (I2C0_A1)
8
R/W
00h
31.3.1/561
4006_6001
I2C Frequency Divider register (I2C0_F)
8
R/W
00h
31.3.2/561
4006_6002
I2C Control Register 1 (I2C0_C1)
8
R/W
00h
31.3.3/562
4006_6003
I2C Status register (I2C0_S)
8
R/W
80h
31.3.4/564
4006_6004
I2C Data I/O register (I2C0_D)
8
R/W
00h
31.3.5/565
4006_6005
I2C Control Register 2 (I2C0_C2)
8
R/W
00h
31.3.6/566
4006_6006
I2C Programmable Input Glitch Filter register (I2C0_FLT)
8
R/W
00h
31.3.7/567
4006_6007
I2C Range Address register (I2C0_RA)
8
R/W
00h
31.3.8/568
4006_6008
I2C SMBus Control and Status register (I2C0_SMB)
8
R/W
00h
31.3.9/569
4006_6009
I2C Address Register 2 (I2C0_A2)
8
R/W
C2h
31.3.10/
571
4006_600A
I2C SCL Low Timeout Register High (I2C0_SLTH)
8
R/W
00h
31.3.11/
571
4006_600B
I2C SCL Low Timeout Register Low (I2C0_SLTL)
8
R/W
00h
31.3.12/
571
4006_7000
I2C Address Register 1 (I2C1_A1)
8
R/W
00h
31.3.1/561
4006_7001
I2C Frequency Divider register (I2C1_F)
8
R/W
00h
31.3.2/561
4006_7002
I2C Control Register 1 (I2C1_C1)
8
R/W
00h
31.3.3/562
4006_7003
I2C Status register (I2C1_S)
8
R/W
80h
31.3.4/564
4006_7004
I2C Data I/O register (I2C1_D)
8
R/W
00h
31.3.5/565
4006_7005
I2C Control Register 2 (I2C1_C2)
8
R/W
00h
31.3.6/566
4006_7006
I2C Programmable Input Glitch Filter register (I2C1_FLT)
8
R/W
00h
31.3.7/567
4006_7007
I2C Range Address register (I2C1_RA)
8
R/W
00h
31.3.8/568
4006_7008
I2C SMBus Control and Status register (I2C1_SMB)
8
R/W
00h
31.3.9/569
4006_7009
I2C Address Register 2 (I2C1_A2)
8
R/W
C2h
31.3.10/
571
4006_700A
I2C SCL Low Timeout Register High (I2C1_SLTH)
8
R/W
00h
31.3.11/
571
4006_700B
I2C SCL Low Timeout Register Low (I2C1_SLTL)
8
R/W
00h
31.3.12/
571
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
560
Freescale Semiconductor, Inc.
Chapter 31 Inter-Integrated Circuit (I2C)
31.3.1 I2C Address Register 1 (I2Cx_A1)
This register contains the slave address to be used by the I2C module.
Address: Base address + 0h offset
Bit
Read
Write
Reset
7
6
5
4
3
2
1
AD[7:1]
0
0
0
0
0
0
0
0
0
0
I2Cx_A1 field descriptions
Field
7–1
AD[7:1]
0
Reserved
Description
Address
Contains the primary slave address used by the I2C module when it is addressed as a slave. This field is
used in the 7-bit address scheme and the lower seven bits in the 10-bit address scheme.
This field is reserved.
This read-only field is reserved and always has the value 0.
31.3.2 I2C Frequency Divider register (I2Cx_F)
Address: Base address + 1h offset
Bit
Read
Write
Reset
7
6
5
4
3
MULT
0
2
1
0
0
0
0
ICR
0
0
0
0
I2Cx_F field descriptions
Field
7–6
MULT
Description
Multiplier Factor
Defines the multiplier factor (mul). This factor is used along with the SCL divider to generate the I2C baud
rate.
00
01
10
11
ICR
mul = 1
mul = 2
mul = 4
Reserved
ClockRate
Prescales the I2C module clock for bit rate selection. This field and the MULT field determine the I2C baud
rate, the SDA hold time, the SCL start hold time, and the SCL stop hold time. For a list of values
corresponding to each ICR setting, see I2C divider and hold values.
The SCL divider multiplied by multiplier factor (mul) determines the I2C baud rate.
I2C baud rate = I2C module clock speed (Hz)/(mul × SCL divider)
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
561
Memory map/register definition
I2Cx_F field descriptions (continued)
Field
Description
The SDA hold time is the delay from the falling edge of SCL (I2C clock) to the changing of SDA (I2C data).
SDA hold time = I2C module clock period (s) × mul × SDA hold value
The SCL start hold time is the delay from the falling edge of SDA (I2C data) while SCL is high (start
condition) to the falling edge of SCL (I2C clock).
SCL start hold time = I2C module clock period (s) × mul × SCL start hold value
The SCL stop hold time is the delay from the rising edge of SCL (I2C clock) to the rising edge of SDA (I2C
data) while SCL is high (stop condition).
SCL stop hold time = I2C module clock period (s) × mul × SCL stop hold value
For example, if the I2C module clock speed is 8 MHz, the following table shows the possible hold time
values with different ICR and MULT selections to achieve an I2C baud rate of 100 kbit/s.
MULT
Hold times (μs)
ICR
SDA
SCL Start
SCL Stop
2h
00h
3.500
3.000
5.500
1h
07h
2.500
4.000
5.250
1h
0Bh
2.250
4.000
5.250
0h
14h
2.125
4.250
5.125
0h
18h
1.125
4.750
5.125
31.3.3 I2C Control Register 1 (I2Cx_C1)
Address: Base address + 2h offset
Bit
Read
Write
Reset
7
6
5
4
3
IICEN
IICIE
MST
TX
TXAK
0
0
0
0
0
2
1
0
WUEN
RSTA
0
0
0
0
0
I2Cx_C1 field descriptions
Field
7
IICEN
Description
I2C Enable
Enables I2C module operation.
0
1
6
IICIE
Disabled
Enabled
I2C Interrupt Enable
Enables I2C interrupt requests.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
562
Freescale Semiconductor, Inc.
Chapter 31 Inter-Integrated Circuit (I2C)
I2Cx_C1 field descriptions (continued)
Field
Description
0
1
5
MST
Master Mode Select
When MST is changed from 0 to 1, a START signal is generated on the bus and master mode is selected.
When this bit changes from 1 to 0, a STOP signal is generated and the mode of operation changes from
master to slave.
0
1
4
TX
Slave mode
Master mode
Transmit Mode Select
Selects the direction of master and slave transfers. In master mode this bit must be set according to the
type of transfer required. Therefore, for address cycles, this bit is always set. When addressed as a slave
this bit must be set by software according to the SRW bit in the status register.
0
1
3
TXAK
Disabled
Enabled
Receive
Transmit
Transmit Acknowledge Enable
Specifies the value driven onto the SDA during data acknowledge cycles for both master and slave
receivers. The value of SMB[FACK] affects NACK/ACK generation.
NOTE: SCL is held low until TXAK is written.
0
1
An acknowledge signal is sent to the bus on the following receiving byte (if FACK is cleared) or the
current receiving byte (if FACK is set).
No acknowledge signal is sent to the bus on the following receiving data byte (if FACK is cleared) or
the current receiving data byte (if FACK is set).
2
RSTA
Repeat START
1
WUEN
Wakeup Enable
Writing 1 to this bit generates a repeated START condition provided it is the current master. This bit will
always be read as 0. Attempting a repeat at the wrong time results in loss of arbitration.
The I2C module can wake the MCU from low power mode with no peripheral bus running when slave
address matching occurs.
0
1
0
Reserved
Normal operation. No interrupt generated when address matching in low power mode.
Enables the wakeup function in low power mode.
This field is reserved.
This read-only field is reserved and always has the value 0.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
563
Memory map/register definition
31.3.4 I2C Status register (I2Cx_S)
Address: Base address + 3h offset
Bit
Read
7
6
TCF
IAAS
Write
Reset
1
5
4
BUSY
ARBL
w1c
0
0
0
3
RAM
0
2
1
0
SRW
IICIF
RXAK
w1c
0
0
0
I2Cx_S field descriptions
Field
7
TCF
Description
Transfer Complete Flag
Acknowledges a byte transfer; TCF sets on the completion of a byte transfer. This bit is valid only during
or immediately following a transfer to or from the I2C module. TCF is cleared by reading the I2C data
register in receive mode or by writing to the I2C data register in transmit mode.
0
1
6
IAAS
Transfer in progress
Transfer complete
Addressed As A Slave
This bit is set by one of the following conditions:
• The calling address matches the programmed primary slave address in the A1 register, or matches
the range address in the RA register (which must be set to a nonzero value and under the condition
I2C_C2[RMEN] = 1).
• C2[GCAEN] is set and a general call is received.
• SMB[SIICAEN] is set and the calling address matches the second programmed slave address.
• ALERTEN is set and an SMBus alert response address is received
• RMEN is set and an address is received that is within the range between the values of the A1 and
RA registers.
IAAS sets before the ACK bit. The CPU must check the SRW bit and set TX/RX accordingly. Writing the
C1 register with any value clears this bit.
0
1
5
BUSY
Bus Busy
Indicates the status of the bus regardless of slave or master mode. This bit is set when a START signal is
detected and cleared when a STOP signal is detected.
0
1
4
ARBL
Bus is idle
Bus is busy
Arbitration Lost
This bit is set by hardware when the arbitration procedure is lost. The ARBL bit must be cleared by
software, by writing 1 to it.
0
1
3
RAM
Not addressed
Addressed as a slave
Standard bus operation.
Loss of arbitration.
Range Address Match
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
564
Freescale Semiconductor, Inc.
Chapter 31 Inter-Integrated Circuit (I2C)
I2Cx_S field descriptions (continued)
Field
Description
This bit is set to 1 by any of the following conditions, if I2C_C2[RMEN] = 1:
• Any nonzero calling address is received that matches the address in the RA register.
• The calling address is within the range of values of the A1 and RA registers.
Writing the C1 register with any value clears this bit to 0.
0
1
2
SRW
Slave Read/Write
When addressed as a slave, SRW indicates the value of the R/W command bit of the calling address sent
to the master.
0
1
1
IICIF
Not addressed
Addressed as a slave
Slave receive, master writing to slave
Slave transmit, master reading from slave
Interrupt Flag
This bit sets when an interrupt is pending. This bit must be cleared by software by writing 1 to it, such as in
the interrupt routine. One of the following events can set this bit:
• One byte transfer, including ACK/NACK bit, completes if FACK is 0. An ACK or NACK is sent on the
bus by writing 0 or 1 to TXAK after this bit is set in receive mode.
• One byte transfer, excluding ACK/NACK bit, completes if FACK is 1.
• Match of slave address to calling address including primary slave address, range slave address,
alert response address, second slave address, or general call address.
• Arbitration lost
• In SMBus mode, any timeouts except SCL and SDA high timeouts
• I2C bus stop or start detection if the SSIE bit in the Input Glitch Filter register is 1
NOTE:
0
1
0
RXAK
To clear the I2C bus stop or start detection interrupt: In the interrupt service
routine, first clear the STOPF or STARTF bit in the Input Glitch Filter register by
writing 1 to it, and then clear the IICIF bit. If this sequence is reversed, the IICIF
bit is asserted again.
No interrupt pending
Interrupt pending
Receive Acknowledge
0
1
Acknowledge signal was received after the completion of one byte of data transmission on the bus
No acknowledge signal detected
31.3.5 I2C Data I/O register (I2Cx_D)
Address: Base address + 4h offset
Bit
Read
Write
Reset
7
6
5
4
3
2
1
0
0
0
0
0
DATA
0
0
0
0
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
565
Memory map/register definition
I2Cx_D field descriptions
Field
DATA
Description
Data
In master transmit mode, when data is written to this register, a data transfer is initiated. The most
significant bit is sent first. In master receive mode, reading this register initiates receiving of the next byte
of data.
NOTE: When making the transition out of master receive mode, switch the I2C mode before reading the
Data register to prevent an inadvertent initiation of a master receive data transfer.
In slave mode, the same functions are available after an address match occurs.
The C1[TX] bit must correctly reflect the desired direction of transfer in master and slave modes for the
transmission to begin. For example, if the I2C module is configured for master transmit but a master
receive is desired, reading the Data register does not initiate the receive.
Reading the Data register returns the last byte received while the I2C module is configured in master
receive or slave receive mode. The Data register does not reflect every byte that is transmitted on the I2C
bus, and neither can software verify that a byte has been written to the Data register correctly by reading it
back.
In master transmit mode, the first byte of data written to the Data register following assertion of MST (start
bit) or assertion of RSTA (repeated start bit) is used for the address transfer and must consist of the
calling address (in bits 7-1) concatenated with the required R/W bit (in position bit 0).
31.3.6 I2C Control Register 2 (I2Cx_C2)
Address: Base address + 5h offset
Bit
Read
Write
Reset
7
6
GCAEN
ADEXT
0
0
5
4
3
0
SBRC
RMEN
0
0
0
2
1
0
AD[10:8]
0
0
0
I2Cx_C2 field descriptions
Field
7
GCAEN
Description
General Call Address Enable
Enables general call address.
0
1
6
ADEXT
Address Extension
Controls the number of bits used for the slave address.
0
1
5
Reserved
4
SBRC
Disabled
Enabled
7-bit address scheme
10-bit address scheme
This field is reserved.
This read-only field is reserved and always has the value 0.
Slave Baud Rate Control
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
566
Freescale Semiconductor, Inc.
Chapter 31 Inter-Integrated Circuit (I2C)
I2Cx_C2 field descriptions (continued)
Field
Description
Enables independent slave mode baud rate at maximum frequency, which forces clock stretching on SCL
in very fast I2C modes. To a slave, an example of a "very fast" mode is when the master transfers at 40
kbit/s but the slave can capture the master's data at only 10 kbit/s.
0
1
3
RMEN
Range Address Matching Enable
This bit controls the slave address matching for addresses between the values of the A1 and RA registers.
When this bit is set, a slave address matching occurs for any address greater than the value of the A1
register and less than or equal to the value of the RA register.
0
1
AD[10:8]
The slave baud rate follows the master baud rate and clock stretching may occur
Slave baud rate is independent of the master baud rate
Range mode disabled. No address matching occurs for an address within the range of values of the
A1 and RA registers.
Range mode enabled. Address matching occurs when a slave receives an address within the range of
values of the A1 and RA registers.
Slave Address
Contains the upper three bits of the slave address in the 10-bit address scheme. This field is valid only
while the ADEXT bit is set.
31.3.7 I2C Programmable Input Glitch Filter register (I2Cx_FLT)
Address: Base address + 6h offset
Bit
Read
Write
Reset
7
6
STOPF
SHEN
w1c
0
0
5
SSIE
0
4
3
2
STARTF
0
0
0
FLT
w1c
0
1
0
0
I2Cx_FLT field descriptions
Field
7
SHEN
Description
Stop Hold Enable
Set this bit to hold off entry to stop mode when any data transmission or reception is occurring.
The following scenario explains the holdoff functionality:
1. The I2C module is configured for a basic transfer, and the SHEN bit is set to 1.
2. A transfer begins.
3. The MCU signals the I2C module to enter stop mode.
4. The byte currently being transferred, including both address and data, completes its transfer.
5. The I2C slave or master acknowledges that the in-transfer byte completed its transfer and
acknowledges the request to enter stop mode.
6. After receiving the I2C module's acknowledgment of the request to enter stop mode, the MCU
determines whether to shut off the I2C module's clock.
If the SHEN bit is set to 1 and the I2C module is in an idle or disabled state when the MCU signals to enter
stop mode, the module immediately acknowledges the request to enter stop mode.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
567
Memory map/register definition
I2Cx_FLT field descriptions (continued)
Field
Description
If SHEN is cleared to 0 and the overall data transmission or reception that was suspended by stop mode
entry was incomplete: To resume the overall transmission or reception after the MCU exits stop mode,
software must reinitialize the transfer by resending the address of the slave.
If the I2C Control Register 1's IICIE bit was set to 1 before the MCU entered stop mode, system software
will receive the interrupt triggered by the I2C Status Register's TCF bit after the MCU wakes from the stop
mode.
0
1
6
STOPF
I2C Bus Stop Detect Flag
Hardware sets this bit when the I2C bus's stop status is detected. The STOPF bit must be cleared by
writing 1 to it.
0
1
5
SSIE
Stop holdoff is disabled. The MCU's entry to stop mode is not gated.
Stop holdoff is enabled.
No stop happens on I2C bus
Stop detected on I2C bus
I2C Bus Stop or Start Interrupt Enable
This bit enables the interrupt for I2C bus stop or start detection.
NOTE: To clear the I2C bus stop or start detection interrupt: In the interrupt service routine, first clear the
STOPF or STARTF bit by writing 1 to it, and then clear the IICIF bit in the status register. If this
sequence is reversed, the IICIF bit is asserted again.
0
1
4
STARTF
I2C Bus Start Detect Flag
Hardware sets this bit when the I2C bus's start status is detected. The STARTF bit must be cleared by
writing 1 to it.
0
1
FLT
Stop or start detection interrupt is disabled
Stop or start detection interrupt is enabled
No start happens on I2C bus
Start detected on I2C bus
I2C Programmable Filter Factor
Controls the width of the glitch, in terms of I2C module clock cycles, that the filter must absorb. For any
glitch whose size is less than or equal to this width setting, the filter does not allow the glitch to pass.
0h
1-Fh
No filter/bypass
Filter glitches up to width of n I2C module clock cycles, where n=1-15d
31.3.8 I2C Range Address register (I2Cx_RA)
Address: Base address + 7h offset
Bit
Read
Write
Reset
7
6
5
4
3
2
1
0
RAD
0
0
0
0
0
0
0
0
0
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
568
Freescale Semiconductor, Inc.
Chapter 31 Inter-Integrated Circuit (I2C)
I2Cx_RA field descriptions
Field
7–1
RAD
0
Reserved
Description
Range Slave Address
This field contains the slave address to be used by the I2C module. The field is used in the 7-bit address
scheme. If I2C_C2[RMEN] is set to 1, any nonzero value write enables this register. This register value
can be considered as a maximum boundary in the range matching mode.
This field is reserved.
This read-only field is reserved and always has the value 0.
31.3.9 I2C SMBus Control and Status register (I2Cx_SMB)
NOTE
When the SCL and SDA signals are held high for a length of
time greater than the high timeout period, the SHTF1 flag sets.
Before reaching this threshold, while the system is detecting
how long these signals are being held high, a master assumes
that the bus is free. However, the SHTF1 bit is set to 1 in the
bus transmission process with the idle bus state.
NOTE
When the TCKSEL bit is set, there is no need to monitor the
SHTF1 bit because the bus speed is too high to match the
protocol of SMBus.
Address: Base address + 8h offset
Bit
Read
Write
Reset
7
6
5
4
FACK
ALERTEN
SIICAEN
TCKSEL
0
0
0
0
3
2
1
SLTF
SHTF1
SHTF2
w1c
0
w1c
0
0
0
SHTF2IE
0
I2Cx_SMB field descriptions
Field
7
FACK
Description
Fast NACK/ACK Enable
For SMBus packet error checking, the CPU must be able to issue an ACK or NACK according to the result
of receiving data byte.
0
1
6
ALERTEN
An ACK or NACK is sent on the following receiving data byte
Writing 0 to TXAK after receiving a data byte generates an ACK. Writing 1 to TXAK after receiving a
data byte generates a NACK.
SMBus Alert Response Address Enable
Enables or disables SMBus alert response address matching.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
569
Memory map/register definition
I2Cx_SMB field descriptions (continued)
Field
Description
NOTE: After the host responds to a device that used the alert response address, you must use software
to put the device's address on the bus. The alert protocol is described in the SMBus specification.
0
1
5
SIICAEN
Second I2C Address Enable
Enables or disables SMBus device default address.
0
1
4
TCKSEL
I2C address register 2 matching is disabled
I2C address register 2 matching is enabled
Timeout Counter Clock Select
Selects the clock source of the timeout counter.
0
1
3
SLTF
SMBus alert response address matching is disabled
SMBus alert response address matching is enabled
Timeout counter counts at the frequency of the I2C module clock / 64
Timeout counter counts at the frequency of the I2C module clock
SCL Low Timeout Flag
This bit is set when the SLT register (consisting of the SLTH and SLTL registers) is loaded with a non-zero
value (LoValue) and an SCL low timeout occurs. Software clears this bit by writing a logic 1 to it.
NOTE: The low timeout function is disabled when the SLT register's value is 0.
0
1
2
SHTF1
SCL High Timeout Flag 1
This read-only bit sets when SCL and SDA are held high more than clock × LoValue / 512, which indicates
the bus is free. This bit is cleared automatically.
0
1
1
SHTF2
No SCL high and SDA high timeout occurs
SCL high and SDA high timeout occurs
SCL High Timeout Flag 2
This bit sets when SCL is held high and SDA is held low more than clock × LoValue / 512. Software clears
this bit by writing 1 to it.
0
1
0
SHTF2IE
No low timeout occurs
Low timeout occurs
No SCL high and SDA low timeout occurs
SCL high and SDA low timeout occurs
SHTF2 Interrupt Enable
Enables SCL high and SDA low timeout interrupt.
0
1
SHTF2 interrupt is disabled
SHTF2 interrupt is enabled
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
570
Freescale Semiconductor, Inc.
Chapter 31 Inter-Integrated Circuit (I2C)
31.3.10 I2C Address Register 2 (I2Cx_A2)
Address: Base address + 9h offset
Bit
Read
Write
Reset
7
6
5
4
3
2
1
SAD
1
1
0
0
0
0
0
0
1
0
I2Cx_A2 field descriptions
Field
7–1
SAD
0
Reserved
Description
SMBus Address
Contains the slave address used by the SMBus. This field is used on the device default address or other
related addresses.
This field is reserved.
This read-only field is reserved and always has the value 0.
31.3.11 I2C SCL Low Timeout Register High (I2Cx_SLTH)
Address: Base address + Ah offset
Bit
Read
Write
Reset
7
6
5
4
3
2
1
0
0
0
0
0
SSLT[15:8]
0
0
0
0
I2Cx_SLTH field descriptions
Field
SSLT[15:8]
Description
Most significant byte of SCL low timeout value that determines the timeout period of SCL low.
31.3.12 I2C SCL Low Timeout Register Low (I2Cx_SLTL)
Address: Base address + Bh offset
Bit
Read
Write
Reset
7
6
5
4
3
2
1
0
0
0
0
0
SSLT[7:0]
0
0
0
0
I2Cx_SLTL field descriptions
Field
SSLT[7:0]
Description
Least significant byte of SCL low timeout value that determines the timeout period of SCL low.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
571
Functional description
31.4 Functional description
This section provides a comprehensive functional description of the I2C module.
31.4.1 I2C protocol
The I2C bus system uses a serial data line (SDA) and a serial clock line (SCL) for data
transfers.
All devices connected to it must have open drain or open collector outputs. A logic AND
function is exercised on both lines with external pull-up resistors. The value of these
resistors depends on the system.
Normally, a standard instance of communication is composed of four parts:
1.
2.
3.
4.
START signal
Slave address transmission
Data transfer
STOP signal
The STOP signal should not be confused with the CPU STOP instruction. The following
figure illustrates I2C bus system communication.
LSB
MSB
SCL
SDA
1
2
3
4
AD7 AD6 AD5 AD4
5
6
AD3 AD2
7
Read/
Write
MSB
SCL
1
SDA
AD7
Start
Signal
XXX
3
4
5
6
7
8
Read/
Write
2
3
4
5
6
7
8
D7
D6
D5
D4
D3
D2
D1
D0
Data Byte
1
9
XX
Ack
Bit
AD7
Repeated
Start
Signal
9
No Stop
Ack Signal
Bit
MSB
AD6 AD5 AD4 AD3 AD2 AD1 R/W
Calling Address
1
Ack
Bit
LSB
2
LSB
MSB
9
AD1 R/W
Calling Address
Start
Signal
8
LSB
2
3
AD6 AD5
4
5
6
AD4 AD3
AD2
7
8
9
AD1 R/W
New Calling Address
Read/
Write
No Stop
Ack Signal
Bit
Figure 31-38. I2C bus transmission signals
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
572
Freescale Semiconductor, Inc.
Chapter 31 Inter-Integrated Circuit (I2C)
31.4.1.1 START signal
The bus is free when no master device is engaging the bus (both SCL and SDA are high).
When the bus is free, a master may initiate communication by sending a START signal.
A START signal is defined as a high-to-low transition of SDA while SCL is high. This
signal denotes the beginning of a new data transfer—each data transfer might contain
several bytes of data—and brings all slaves out of their idle states.
31.4.1.2 Slave address transmission
Immediately after the START signal, the first byte of a data transfer is the slave address
transmitted by the master. This address is a 7-bit calling address followed by an R/W bit.
The R/W bit tells the slave the desired direction of data transfer.
• 1 = Read transfer: The slave transmits data to the master
• 0 = Write transfer: The master transmits data to the slave
Only the slave with a calling address that matches the one transmitted by the master
responds by sending an acknowledge bit. The slave sends the acknowledge bit by pulling
SDA low at the ninth clock.
No two slaves in the system can have the same address. If the I2C module is the master, it
must not transmit an address that is equal to its own slave address. The I2C module
cannot be master and slave at the same time. However, if arbitration is lost during an
address cycle, the I2C module reverts to slave mode and operates correctly even if it is
being addressed by another master.
31.4.1.3 Data transfers
When successful slave addressing is achieved, data transfer can proceed on a byte-bybyte basis in the direction specified by the R/W bit sent by the calling master.
All transfers that follow an address cycle are referred to as data transfers, even if they
carry subaddress information for the slave device.
Each data byte is 8 bits long. Data may be changed only while SCL is low. Data must be
held stable while SCL is high. There is one clock pulse on SCL for each data bit, and the
MSB is transferred first. Each data byte is followed by a ninth (acknowledge) bit, which
is signaled from the receiving device by pulling SDA low at the ninth clock. In summary,
one complete data transfer needs nine clock pulses.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
573
Functional description
If the slave receiver does not acknowledge the master in the ninth bit, the slave must
leave SDA high. The master interprets the failed acknowledgement as an unsuccessful
data transfer.
If the master receiver does not acknowledge the slave transmitter after a data byte
transmission, the slave interprets it as an end to data transfer and releases the SDA line.
In the case of a failed acknowledgement by either the slave or master, the data transfer is
aborted and the master does one of two things:
• Relinquishes the bus by generating a STOP signal.
• Commences a new call by generating a repeated START signal.
31.4.1.4 STOP signal
The master can terminate the communication by generating a STOP signal to free the
bus. A STOP signal is defined as a low-to-high transition of SDA while SCL is asserted.
The master can generate a STOP signal even if the slave has generated an
acknowledgement, at which point the slave must release the bus.
31.4.1.5 Repeated START signal
The master may generate a START signal followed by a calling command without
generating a STOP signal first. This action is called a repeated START. The master uses
a repeated START to communicate with another slave or with the same slave in a
different mode (transmit/receive mode) without releasing the bus.
31.4.1.6 Arbitration procedure
The I2C bus is a true multimaster bus that allows more than one master to be connected
on it.
If two or more masters try to control the bus at the same time, a clock synchronization
procedure determines the bus clock. The bus clock's low period is equal to the longest
clock low period, and the high period is equal to the shortest one among the masters.
The relative priority of the contending masters is determined by a data arbitration
procedure. A bus master loses arbitration if it transmits logic level 1 while another master
transmits logic level 0. The losing masters immediately switch to slave receive mode and
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
574
Freescale Semiconductor, Inc.
Chapter 31 Inter-Integrated Circuit (I2C)
stop driving SDA output. In this case, the transition from master to slave mode does not
generate a STOP condition. Meanwhile, hardware sets a status bit to indicate the loss of
arbitration.
31.4.1.7 Clock synchronization
Because wire AND logic is performed on SCL, a high-to-low transition on SCL affects
all devices connected on the bus. The devices start counting their low period and, after a
device's clock has gone low, that device holds SCL low until the clock reaches its high
state. However, the change of low to high in this device clock might not change the state
of SCL if another device clock is still within its low period. Therefore, the synchronized
clock SCL is held low by the device with the longest low period. Devices with shorter
low periods enter a high wait state during this time; see the following diagram. When all
applicable devices have counted off their low period, the synchronized clock SCL is
released and pulled high. Afterward there is no difference between the device clocks and
the state of SCL, and all devices start counting their high periods. The first device to
complete its high period pulls SCL low again.
Delay
Start Counting High Period
SCL2
SCL1
SCL
Internal Counter Reset
Figure 31-39. I2C clock synchronization
31.4.1.8 Handshaking
The clock synchronization mechanism can be used as a handshake in data transfers. A
slave device may hold SCL low after completing a single byte transfer (9 bits). In this
case, it halts the bus clock and forces the master clock into wait states until the slave
releases SCL.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
575
Functional description
31.4.1.9 Clock stretching
The clock synchronization mechanism can be used by slaves to slow down the bit rate of
a transfer. After the master drives SCL low, a slave can drive SCL low for the required
period and then release it. If the slave's SCL low period is greater than the master's SCL
low period, the resulting SCL bus signal's low period is stretched. In other words, the
SCL bus signal's low period is increased to be the same length as the slave's SCL low
period.
31.4.1.10 I2C divider and hold values
NOTE
For some cases on some devices, the SCL divider value may
vary by ±2 or ±4 when ICR's value ranges from 00h to 0Fh.
These potentially varying SCL divider values are highlighted in
the following table. For the actual SCL divider values for your
device, see the chip-specific details about the I2C module.
Table 31-41. I2C divider and hold values
ICR
SCL
divider
SDA hold
value
SCL hold
(start)
value
SCL hold
(stop)
value
SCL
divider
(clocks)
SDA hold
(clocks)
SCL hold
(start)
value
SCL hold
(stop)
value
00
20
7
6
11
20
160
17
78
81
01
22
7
7
12
21
192
17
94
97
02
24
8
8
13
22
224
33
110
113
03
26
8
9
14
23
256
33
126
129
04
28
9
10
15
24
288
49
142
145
05
06
30
9
11
16
25
320
49
158
161
34
10
13
18
26
384
65
190
193
07
40
10
16
21
27
480
65
238
241
08
28
7
10
15
28
320
33
158
161
09
32
7
12
17
29
384
33
190
193
0A
36
9
14
19
2A
448
65
222
225
0B
40
9
16
21
2B
512
65
254
257
0C
44
11
18
23
2C
576
97
286
289
0D
48
11
20
25
2D
640
97
318
321
0E
56
13
24
29
2E
768
129
382
385
0F
68
13
30
35
2F
960
129
478
481
10
48
9
18
25
30
640
65
318
321
11
56
9
22
29
31
768
65
382
385
12
64
13
26
33
32
896
129
446
449
13
72
13
30
37
33
1024
129
510
513
(hex)
ICR
(hex)
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
576
Freescale Semiconductor, Inc.
Chapter 31 Inter-Integrated Circuit (I2C)
Table 31-41. I2C divider and hold values (continued)
ICR
SCL
divider
SDA hold
value
SCL hold
(start)
value
SCL hold
(stop)
value
SCL
divider
(clocks)
SDA hold
(clocks)
SCL hold
(start)
value
SCL hold
(stop)
value
14
80
17
34
41
34
1152
193
574
577
15
88
17
38
45
35
1280
193
638
641
16
104
21
46
53
36
1536
257
766
769
17
128
18
80
21
58
65
37
1920
257
958
961
9
38
41
38
1280
129
638
641
19
96
9
46
49
39
1536
129
766
769
1A
112
17
54
57
3A
1792
257
894
897
1B
128
17
62
65
3B
2048
257
1022
1025
1C
144
25
70
73
3C
2304
385
1150
1153
1D
160
25
78
81
3D
2560
385
1278
1281
1E
192
33
94
97
3E
3072
513
1534
1537
1F
240
33
118
121
3F
3840
513
1918
1921
(hex)
ICR
(hex)
31.4.2 10-bit address
For 10-bit addressing, 0x11110 is used for the first 5 bits of the first address byte.
Various combinations of read/write formats are possible within a transfer that includes
10-bit addressing.
31.4.2.1 Master-transmitter addresses a slave-receiver
The transfer direction is not changed. When a 10-bit address follows a START condition,
each slave compares the first 7 bits of the first byte of the slave address (11110XX) with
its own address and tests whether the eighth bit (R/W direction bit) is 0. It is possible that
more than one device finds a match and generates an acknowledge (A1). Each slave that
finds a match compares the 8 bits of the second byte of the slave address with its own
address, but only one slave finds a match and generates an acknowledge (A2). The
matching slave remains addressed by the master until it receives a STOP condition (P) or
a repeated START condition (Sr) followed by a different slave address.
Table 31-42. Master-transmitter addresses slave-receiver with a 10-bit
address
S
Slave
address
first 7 bits
11110 +
R/W
0
A1
Slave
address
second
byte
AD[8:1]
A2
Data
A
...
Data
A/A
P
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
577
Functional description
Table 31-42. Master-transmitter addresses slave-receiver with a 10-bit
address
AD10 +
AD9
After the master-transmitter has sent the first byte of the 10-bit address, the slave-receiver
sees an I2C interrupt. User software must ensure that for this interrupt, the contents of the
Data register are ignored and not treated as valid data.
31.4.2.2 Master-receiver addresses a slave-transmitter
The transfer direction is changed after the second R/W bit. Up to and including
acknowledge bit A2, the procedure is the same as that described for a master-transmitter
addressing a slave-receiver. After the repeated START condition (Sr), a matching slave
remembers that it was addressed before. This slave then checks whether the first seven
bits of the first byte of the slave address following Sr are the same as they were after the
START condition (S), and it tests whether the eighth (R/W) bit is 1. If there is a match,
the slave considers that it has been addressed as a transmitter and generates acknowledge
A3. The slave-transmitter remains addressed until it receives a STOP condition (P) or a
repeated START condition (Sr) followed by a different slave address.
After a repeated START condition (Sr), all other slave devices also compare the first
seven bits of the first byte of the slave address with their own addresses and test the
eighth (R/W) bit. However, none of them are addressed because R/W = 1 (for 10-bit
devices), or the 11110XX slave address (for 7-bit devices) does not match.
Table 31-43. Master-receiver addresses a slave-transmitter with a 10-bit
address
S
Slave
address
first 7
bits
11110 +
AD10 +
AD9
R/W
0
A1
Slave
address
second
byte
AD[8:1]
A2
Sr
Slave
address
first 7
bits
11110 +
AD10 +
AD9
R/W
1
A3
Data
A
...
Data
A
P
After the master-receiver has sent the first byte of the 10-bit address, the slave-transmitter
sees an I2C interrupt. User software must ensure that for this interrupt, the contents of the
Data register are ignored and not treated as valid data.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
578
Freescale Semiconductor, Inc.
Chapter 31 Inter-Integrated Circuit (I2C)
31.4.3 Address matching
All received addresses can be requested in 7-bit or 10-bit address format.
• AD[7:1] in Address Register 1, which contains the I2C primary slave address, always
participates in the address matching process. It provides a 7-bit address.
• If the ADEXT bit is set, AD[10:8] in Control Register 2 participates in the address
matching process. It extends the I2C primary slave address to a 10-bit address.
Additional conditions that affect address matching include:
• If the GCAEN bit is set, general call participates the address matching process.
• If the ALERTEN bit is set, alert response participates the address matching process.
• If the SIICAEN bit is set, Address Register 2 participates in the address matching
process.
• If the RMEN bit is set, when the Range Address register is programmed to a nonzero
value, any address within the range of values of Address Register 1 (excluded) and
the Range Address register (included) participates in the address matching process.
The Range Address register must be programmed to a value greater than the value of
Address Register 1.
When the I2C module responds to one of these addresses, it acts as a slave-receiver and
the IAAS bit is set after the address cycle. Software must read the Data register after the
first byte transfer to determine that the address is matched.
31.4.4 System management bus specification
SMBus provides a control bus for system and power management related tasks. A system
can use SMBus to pass messages to and from devices instead of tripping individual
control lines.
Removing the individual control lines reduces pin count. Accepting messages ensures
future expandability. With the system management bus, a device can provide
manufacturer information, tell the system what its model/part number is, save its state for
a suspend event, report different types of errors, accept control parameters, and return its
status.
31.4.4.1 Timeouts
The TTIMEOUT,MIN parameter allows a master or slave to conclude that a defective device
is holding the clock low indefinitely or a master is intentionally trying to drive devices
off the bus. The slave device must release the bus (stop driving the bus and let SCL and
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
579
Functional description
SDA float high) when it detects any single clock held low longer than TTIMEOUT,MIN.
Devices that have detected this condition must reset their communication and be able to
receive a new START condition within the timeframe of TTIMEOUT,MAX.
SMBus defines a clock low timeout, TTIMEOUT, of 35 ms, specifies TLOW:SEXT as the
cumulative clock low extend time for a slave device, and specifies TLOW:MEXT as the
cumulative clock low extend time for a master device.
31.4.4.1.1
SCL low timeout
If the SCL line is held low by a slave device on the bus, no further communication is
possible. Furthermore, the master cannot force the SCL line high to correct the error
condition. To solve this problem, the SMBus protocol specifies that devices participating
in a transfer must detect any clock cycle held low longer than a timeout value condition.
Devices that have detected the timeout condition must reset the communication. When
the I2C module is an active master, if it detects that SMBCLK low has exceeded the
value of TTIMEOUT,MIN, it must generate a stop condition within or after the current data
byte in the transfer process. When the I2C module is a slave, if it detects the
TTIMEOUT,MIN condition, it resets its communication and is then able to receive a new
START condition.
31.4.4.1.2
SCL high timeout
When the I2C module has determined that the SMBCLK and SMBDAT signals have
been high for at least THIGH:MAX, it assumes that the bus is idle.
A HIGH timeout occurs after a START condition appears on the bus but before a STOP
condition appears on the bus. Any master detecting this scenario can assume the bus is
free when either of the following occurs:
• SHTF1 rises.
• The BUSY bit is high and SHTF1 is high.
When the SMBDAT signal is low and the SMBCLK signal is high for a period of time,
another kind of timeout occurs. The time period must be defined in software. SHTF2 is
used as the flag when the time limit is reached. This flag is also an interrupt resource, so
it triggers IICIF.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
580
Freescale Semiconductor, Inc.
Chapter 31 Inter-Integrated Circuit (I2C)
31.4.4.1.3
CSMBCLK TIMEOUT MEXT and CSMBCLK TIMEOUT SEXT
The following figure illustrates the definition of the timeout intervals TLOW:SEXT and
TLOW:MEXT. When in master mode, the I2C module must not cumulatively extend its
clock cycles for a period greater than TLOW:MEXT within a byte, where each byte is
defined as START-to-ACK, ACK-to-ACK, or ACK-to-STOP. When CSMBCLK
TIMEOUT MEXT occurs, SMBus MEXT rises and also triggers the SLTF.
Stop
T LOW:SEXT
Start
T LOW:MEXT
ClkAck
T LOW:MEXT
ClkAck
T LOW:MEXT
SCL
SDA
Figure 31-40. Timeout measurement intervals
A master is allowed to abort the transaction in progress to any slave that violates the
TLOW:SEXT or TTIMEOUT,MIN specifications. To abort the transaction, the master issues a
STOP condition at the conclusion of the byte transfer in progress. When a slave, the I2C
module must not cumulatively extend its clock cycles for a period greater than
TLOW:SEXT during any message from the initial START to the STOP. When CSMBCLK
TIMEOUT SEXT occurs, SEXT rises and also triggers SLTF.
NOTE
CSMBCLK TIMEOUT SEXT and CSMBCLK TIMEOUT
MEXT are optional functions that are implemented in the
second step.
31.4.4.2 FAST ACK and NACK
To improve reliability and communication robustness, implementation of packet error
checking (PEC) by SMBus devices is optional for SMBus devices but required for
devices participating in and only during the address resolution protocol (ARP) process.
The PEC is a CRC-8 error checking byte, calculated on all the message bytes. The PEC is
appended to the message by the device that supplied the last data byte. If the PEC is
present but not correct, a NACK is issued by the receiver. Otherwise an ACK is issued.
To calculate the CRC-8 by software, this module can hold the SCL line low after
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
581
Functional description
receiving the eighth SCL (8th bit) if this byte is a data byte. So software can determine
whether an ACK or NACK should be sent to the bus by setting or clearing the TXAK bit
if the FACK (fast ACK/NACK enable) bit is enabled.
SMBus requires a device always to acknowledge its own address, as a mechanism to
detect the presence of a removable device (such as a battery or docking station) on the
bus. In addition to indicating a slave device busy condition, SMBus uses the NACK
mechanism to indicate the reception of an invalid command or invalid data. Because such
a condition may occur on the last byte of the transfer, SMBus devices are required to
have the ability to generate the not acknowledge after the transfer of each byte and before
the completion of the transaction. This requirement is important because SMBus does not
provide any other resend signaling. This difference in the use of the NACK signaling has
implications on the specific implementation of the SMBus port, especially in devices that
handle critical system data such as the SMBus host and the SBS components.
NOTE
In the last byte of master receive slave transmit mode, the
master must send a NACK to the bus, so FACK must be
switched off before the last byte transmits.
31.4.5 Resets
The I2C module is disabled after a reset. The I2C module cannot cause a core reset.
31.4.6 Interrupts
The I2C module generates an interrupt when any of the events in the table found here
occur, provided that the IICIE bit is set.
The interrupt is driven by the IICIF bit (of the I2C Status Register) and masked with the
IICIE bit (of the I2C Control Register 1). The IICIF bit must be cleared (by software) by
writing 1 to it in the interrupt routine. The SMBus timeouts interrupt is driven by SLTF
and masked with the IICIE bit. The SLTF bit must be cleared by software by writing 1 to
it in the interrupt routine. You can determine the interrupt type by reading the Status
Register.
NOTE
In master receive mode, the FACK bit must be set to zero
before the last byte transfer.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
582
Freescale Semiconductor, Inc.
Chapter 31 Inter-Integrated Circuit (I2C)
Table 31-44. Interrupt summary
Interrupt source
Status
Flag
Local enable
Complete 1-byte transfer
TCF
IICIF
IICIE
Match of received calling address
IAAS
IICIF
IICIE
Arbitration lost
ARBL
IICIF
IICIE
I2C
bus stop detection
STOPF
IICIF
IICIE & SSIE
I2C
bus start detection
STARTF
IICIF
IICIE & SSIE
SMBus SCL low timeout
SLTF
IICIF
IICIE
SMBus SCL high SDA low timeout
SHTF2
IICIF
IICIE & SHTF2IE
Wakeup from stop or wait mode
IAAS
IICIF
IICIE & WUEN
31.4.6.1 Byte transfer interrupt
The Transfer Complete Flag (TCF) bit is set at the falling edge of the ninth clock to
indicate the completion of a byte and acknowledgement transfer. When FACK is enabled,
TCF is then set at the falling edge of eighth clock to indicate the completion of byte.
31.4.6.2 Address detect interrupt
When the calling address matches the programmed slave address (I2C Address Register)
or when the GCAEN bit is set and a general call is received, the IAAS bit in the Status
Register is set. The CPU is interrupted, provided the IICIE bit is set. The CPU must
check the SRW bit and set its Tx mode accordingly.
31.4.6.3 Stop Detect Interrupt
When the stop status is detected on the I2C bus, the STOPF bit is set to 1. The CPU is
interrupted, provided the IICIE and STOPIE bits are both set to 1.
31.4.6.4 Exit from low-power/stop modes
The slave receive input detect circuit and address matching feature are still active on low
power modes (wait and stop). An asynchronous input matching slave address or general
call address brings the CPU out of low power/stop mode if the interrupt is not masked.
Therefore, TCF and IAAS both can trigger this interrupt.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
583
Functional description
31.4.6.5 Arbitration lost interrupt
The I2C is a true multimaster bus that allows more than one master to be connected on it.
If two or more masters try to control the bus at the same time, the relative priority of the
contending masters is determined by a data arbitration procedure. The I2C module asserts
the arbitration-lost interrupt when it loses the data arbitration process and the ARBL bit
in the Status Register is set.
Arbitration is lost in the following circumstances:
1. SDA is sampled as low when the master drives high during an address or data
transmit cycle.
2. SDA is sampled as low when the master drives high during the acknowledge bit of a
data receive cycle.
3. A START cycle is attempted when the bus is busy.
4. A repeated START cycle is requested in slave mode.
5. A STOP condition is detected when the master did not request it.
The ARBL bit must be cleared (by software) by writing 1 to it.
31.4.6.6 Timeout interrupt in SMBus
When the IICIE bit is set, the I2C module asserts a timeout interrupt (outputs SLTF and
SHTF2) upon detection of any of the mentioned timeout conditions, with one exception.
The SCL high and SDA high TIMEOUT mechanism must not be used to influence the
timeout interrupt output, because this timeout indicates an idle condition on the bus.
SHTF1 rises when it matches the SCL high and SDA high TIMEOUT and falls
automatically just to indicate the bus status. The SHTF2's timeout period is the same as
that of SHTF1, which is short compared to that of SLTF, so another control bit,
SHTF2IE, is added to enable or disable it.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
584
Freescale Semiconductor, Inc.
Chapter 31 Inter-Integrated Circuit (I2C)
31.4.7 Programmable input glitch filter
An I2C glitch filter has been added outside legacy I2C modules but within the I2C
package. This filter can absorb glitches on the I2C clock and data lines for the I2C
module.
The width of the glitch to absorb can be specified in terms of the number of (half) I2C
module clock cycles. A single Programmable Input Glitch Filter control register is
provided. Effectively, any down-up-down or up-down-up transition on the data line that
occurs within the number of clock cycles programmed in this register is ignored by the
I2C module. The programmer must specify the size of the glitch (in terms of I2C module
clock cycles) for the filter to absorb and not pass.
Noise
suppress
circuits
SCL, SDA
internal signals
SCL, SDA
external signals
DFF
DFF
DFF
DFF
Figure 31-41. Programmable input glitch filter diagram
31.4.8 Address matching wake-up
When a primary, range, or general call address match occurs when the I2C module is in
slave receive mode, the MCU wakes from a low power mode where no peripheral bus is
running.
After the address matching IAAS bit is set, an interrupt is sent at the end of address
matching to wake the core.
NOTE
During the wake-up process, if an external master continues to
send data to the slave, the baud rate under Stop mode must be
less than 50 kbit/s. To avoid the slower baud rate under Stop
mode, the master can add a short delay in firmware to wait until
the wake-up process is complete and then send data.
NOTE
Wake-up caused by an address match is not supported for
SMBus mode.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
585
Initialization/application information
31.5 Initialization/application information
Module Initialization (Slave)
1. Write: Control Register 2
• to enable or disable general call
• to select 10-bit or 7-bit addressing mode
2. Write: Address Register 1 to set the slave address
3. Write: Control Register 1 to enable the I2C module and interrupts
4. Initialize RAM variables (IICEN = 1 and IICIE = 1) for transmit data
5. Initialize RAM variables used to achieve the routine shown in the following figure
Module Initialization (Master)
1. Write: Frequency Divider register to set the I2C baud rate (see example in
description of ICR)
2. Write: Control Register 1 to enable the I2C module and interrupts
3. Initialize RAM variables (IICEN = 1 and IICIE = 1) for transmit data
4. Initialize RAM variables used to achieve the routine shown in the following figure
5. Write: Control Register 1 to enable TX
6. Write: Control Register 1 to enable MST (master mode)
7. Write: Data register with the address of the target slave (the LSB of this byte
determines whether the communication is master receive or transmit)
The routine shown in the following figure encompasses both master and slave I2C
operations. For slave operation, an incoming I2C message that contains the proper
address begins I2C communication. For master operation, communication must be
initiated by writing the Data register. An example of an I2C driver which implements
many of the steps described here is available in AN4342: Using the Inter-Integrated
Circuit on ColdFire+ and Kinetis .
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
586
Freescale Semiconductor, Inc.
Chapter 31 Inter-Integrated Circuit (I2C)
Clear IICIF
Y
Tx
Master
mode?
N
Rx
Y
Tx/Rx?
Last byte
transmitted?
Y
Arbitration
lost?
N
Clear ARBL
N
N
Last byte
to be read?
RXAK=0?
N
End of
address cycle
(master Rx)?
Y
Y
(read)
2nd to
last byte to be
read?
Write next
byte to Data reg
Set TXACK
Address transfer
see note 1
N Data transfer
see note 2
Tx/Rx?
Tx
Y
Generate stop
signal (MST=0)
IIAAS=1?
Rx
SRW=1?
N (write)
N
N
Y
IIAAS=1?
Y
N
Y
Y
Y
Set TX mode
ACK from
receiver?
N
Write data
to Data reg
Switch to
Rx mode
Dummy read
from Data reg
Generate stop
signal (MST=0)
Read data from
Data reg
and store
Read data from
Data reg
and store
Transmit
next byte
Set Rx mode
Switch to
Rx mode
Dummy read
from Data reg
Dummy read
from Data reg
RTI
Notes:
1. If general call is enabled, check to determine if the received address is a general call address (0x00).
If the received address is a general call address, the general call must be handled by user software.
2. When 10-bit addressing addresses a slave, the slave sees an interrupt following the first byte of the extended address.
Ensure that for this interrupt, the contents of the Data register are ignored and not treated as a valid data transfer.
Figure 31-42. Typical I2C interrupt routine
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
587
Initialization/application information
Entry of ISR
Y
SLTF=1 or
SHTF2=1?
N
N
FACK=1?
See typical I2C
interrupt routine
flow chart
Y
Clear IICIF
Y
Tx
Master
mode?
N
Rx
Y
Tx/Rx?
Y
Last byte
transmitted?
Last byte
to be read?
Y
N
Clear ARBL
N
N
Y
N
RXAK=0?
2nd to
last byte to be
read?
N
N
Y
Y
Arbitration
lost?
Y
Read data from
Data reg
and soft CRC
End of
address cycle
(master Rx)?
Y
(read)
Read data and
Soft CRC
N
Address transfer
(see note 1)
SRW=1?
Rx
N (write)
Set TXAK to
proper value
Delay (note 2)
Clear IICIF
Y
IAAS=1?
N
Set TXAK to
proper value,
Clear IICIF
Set TXAK to
proper value
Delay (note 2)
Clear IICIF
Switch to
Rx mode
Tx/Rx?
ACK from
receiver?
Set TXACK=1,
Clear FACK=0
Write next
byte to Data reg
N
Tx
Read data from
Data reg
and soft CRC
Generate stop
signal (MST=0)
IAAS=1?
Set Tx mode
Read data from
Data reg
and soft CRC
Set TXAK to
proper value,
Clear IICIF
Y
Clear IICIF
Transmit
next byte
Switch to
Rx mode
Delay (note 2)
Delay (note 2)
Dummy read
from Data reg
Generate stop
signal (MST=0)
Read data from
Data reg
and store
Write data
to Data reg
Read data from
Data reg
and store (note 3)
Dummy read
from Data reg
RTI
Notes:
1. If general call or SIICAEN is enabled, check to determine if the received address is a general call address (0x00) or an SMBus
device default address. In either case, they must be handled by user software.
2. In receive mode, one bit time delay may be needed before the first and second data reading, to wait for the possible longest time
period (in worst case) of the 9th SCL cycle.
3. This read is a dummy read in order to reset the SMBus receiver state machine.
Figure 31-43. Typical I2C SMBus interrupt routine
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
588
Freescale Semiconductor, Inc.
Chapter 32
Freescale's Scalable Controller Area Network
(MSCAN)
32.1 Introduction
Freescale's scalable controller area network (MSCAN) is a communication controller
implementing the CAN 2.0A/B protocol as defined in the Bosch specification dated
September 1991. For users to fully understand the MSCAN specification, it is
recommended that the Bosch specification be read first to familiarize the reader with the
terms and concepts contained within this document.
Though not exclusively intended for automotive applications, CAN protocol is designed
to meet the specific requirements of a vehicle serial data bus: real-time processing,
reliable operation in the EMI environment of a vehicle, cost-effectiveness, and required
bandwidth.
MSCAN uses an advanced buffer arrangement resulting in predictable real-time behavior
and simplified application software.
32.1.1 Glossary
Table 32-1. Terminology
Term
Description
ACK
Acknowledge of CAN message
CAN
Controller area network
CRC
Cyclic redundancy code
EOF
End of frame
FIFO
First-In-First-Out memory
IFS
Inter-Frame sequence
SOF
Start of Frame
CPU bus
CPU related read/write data bus
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
589
Introduction
Table 32-1. Terminology (continued)
Term
Description
CAN bus
CAN protocol related serial bus
oscillator clock
Direct clock from external oscillator
bus clock
CPU bus related clock
CAN clock
CAN protocol related clock
32.1.2 Block diagram
The following figure is the block diagram of the MSCAN
MSCAN
CANCLK
Oscillator Clock
Presc.
MUX
Bus Clock
Tq Clk
RXCAN
Receive/
Transmit
Engine
Transmit Interrupt Req.
Control
and
Status
Receive Interrupt Req.
Errors Interrupt Req.
Message
Filtering
and
Buffering
Wake-Up Interrupt Req.
Configuration
Registers
TXCAN
Wake-Up
Low Pass Filter
Figure 32-1. MSCAN Block Diagram
32.1.3 Features
The basic features of the MSCAN are as follows:
• Implementation of the CAN protocol - Version 2.0A/B
• Standard and extended data frames
• Zero to eight bytes data length
• Programmable bit rate up to 1 Mbps1
• Support for remote frames
• Five receive buffers with FIFO storage scheme
1.
Depending on the actual bit timing and the clock jitter of the PLL.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
590
Freescale Semiconductor, Inc.
Chapter 32 Freescale's Scalable Controller Area Network (MSCAN)
• Three transmit buffers with internal prioritization using a "local priority" concept
• Flexible maskable identifier filter supports two full-size (32-bit) extended identifier
filters, or four 16-bit filters, or eight 8-bit filters
• Programmable wake-up functionality with integrated low-pass filter
• Programmable loopback mode supports self-test operation
• Programmable listen-only mode for monitoring of CAN bus
• Programmable bus-off recovery functionality
• Separate signalling and interrupt capabilities for all CAN receiver and transmitter
error states (warning, error passive, bus-off)
• Programmable MSCAN clock source either bus clock or oscillator clock
• Internal timer for time-stamping of received and transmitted messages
• Three low-power modes: sleep, power down, and MSCAN enable
• Global initialization of configuration registers
32.1.4 Modes of operation
32.1.4.1 Normal system operating modes
The MSCAN module behaves as described within this specification in all normal system
operating modes. Write restrictions exist for some registers.
32.1.4.2 Special system operating modes
The MSCAN module behaves as described within this specification in all special system
operating modes. Write restrictions which exist on specific registers in normal modes are
lifted for test purposes in special modes.
32.1.4.3 Emulation modes
In all emulation modes, the MSCAN module behaves just like in normal system
operating modes as described within this specification.
32.1.4.4 Listen-only mode
In an optional CAN bus monitoring mode (listen-only), the CAN node is able to receive
valid data frames and valid remote frames, but it sends only "recessive" bits on the CAN
bus. In addition, it cannot start a transmission.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
591
Introduction
If the MAC sub-layer is required to send a "dominant" bit (ACK bit, overload flag, or
active error flag), the bit is rerouted internally so that the MAC sub-layer monitors this
"dominant" bit, although the CAN bus may remain in recessive state externally.
32.1.4.5 MSCAN initialization mode
MSCAN Initialization Mode The MSCAN enters initialization mode when it is enabled
(CANE=1).
When entering initialization mode during operation, any on-going transmission or
reception is immediately aborted and synchronization to the CAN bus is lost, potentially
causing CAN protocol violations. To protect the CAN bus system from fatal
consequences of violations, the MSCAN immediately drives TXCAN into a recessive
state.
NOTE
The user is responsible for ensuring that the MSCAN is not
active when initialization mode is entered. The recommended
procedure is to bring the MSCAN into sleep mode (SLPRQ = 1
and SLPAK = 1) before setting the INITRQ bit in the
CANCTL0 register. Otherwise, the abort of an on-going
message can cause an error condition and can impact other
CAN bus devices.
In initialization mode, the MSCAN is stopped. However, interface registers remain
accessible. This mode is used to reset the CANCTL0, CANRFLG, CANRIER,
CANTFLG, CANTIER, CANTARQ, CANTAAK, and CANTBSEL registers to their
default values. In addition, the MSCAN enables the configuration of the CANBTR0,
CANBTR1 bit timing registers; CANIDAC; and the CANIDAR, CANIDMR message
filters.
Bus Clock Domain
CAN Clock Domain
INITRQ
SYNC
sync.
INITAK
SYNC
CPU
Init Request
INITAK
Flag
INIT
Flag
sync.
INITRQ
INITAK
Figure 32-2. Initialization request/acknowledge cycle
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
592
Freescale Semiconductor, Inc.
Chapter 32 Freescale's Scalable Controller Area Network (MSCAN)
Due to independent clock domains within the MSCAN, INITRQ must be synchronized to
all domains by using a special handshake mechanism. This handshake causes additional
synchronization delay (see Figure 32-2).
If there is no message transfer ongoing on the CAN bus, the minimum delay will be two
additional bus clocks and three additional CAN clocks. When all parts of the MSCAN are
in initialization mode, the INITAK flag is set. The application software must use INITAK
as a handshake indication for the request (INITRQ) to go into initialization mode.
NOTE
The CPU cannot clear INITRQ before initialization mode
(INITRQ = 1 and INITAK = 1) is active.
32.2 External signal description
The MSCAN uses two external pins.
NOTE
On MCUs with an integrated CAN physical interface
(transceiver) the MSCAN interface is connected internally to
the transceiver interface. In these cases the external availability
of signals TXCAN and RXCAN is optional.
Table 32-2. MSCAN signal descriptions
Signal
Description
I/O
Function
RXCAN
CAN receiver input pin
I
-
TXCAN
CAN transmitter output pin
O
The TXCAN output pin represents the logic level on the CAN
bus:
• 0 = Dominant state
• 1 = Recessive state
32.2.1 CAN system
A typical CAN system with MSCAN is shown in the following figure. Each CAN station
is connected physically to the CAN bus lines through a transceiver device. The
transceiver is capable of driving the large current needed for the CAN bus and has current
protection against defective CAN or defective stations.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
593
Memory map and register definition
CAN node 2
CAN node 1
CAN node n
MCU
CAN Controller
(MSCAN)
RXCAN
TXCAN
Transceiver
CANH
CANL
CAN Bus
Figure 32-3. CAN system
32.3 Memory map and register definition
32.3.1 Programmer's model of message storage
Each of the receive and transmit message buffers allocates 16 bytes in the memory map
containing a 13 byte data structure.
An additional transmit buffer priority register (TBPR) is defined for the transmit buffers.
Within the last two bytes of this memory map, the MSCAN stores a special 16-bit time
stamp, which is sampled from an internal timer after successful transmission or reception
of a message. This feature is only available for transmit and receiver buffers, if the
CANCTL0[TIME] is set.
The time stamp register is written by the MSCAN. The CPU can only read these
registers.
The following table shows the registers that the data structure of receive and transmit
buffers for extended identifiers and standard identifiers mapping to.
Table 32-3. Message buffer organization
Offset address
Extended identifiers
Standard identifiers
0x0020
REIDR0
RSIDR0
0x0021
REIDR1
RSIDR1
0x0022
REIDR2
0x0023
REIDR3
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
594
Freescale Semiconductor, Inc.
Chapter 32 Freescale's Scalable Controller Area Network (MSCAN)
Table 32-3. Message buffer organization (continued)
Offset address
Extended identifiers
0x0024
REDSR0
0x0025
REDSR1
0x0026
REDSR2
0x0027
REDSR3
0x0028
REDSR4
0x0029
REDSR5
0x002A
REDSR6
Standard identifiers
0x002B
REDSR7
0x002C
RDLR
0x0030
TEIDR0
TSIDR0
0x0031
TEIDR1
TSIDR1
0x0032
TEIDR2
0x0033
TEIDR3
0x0034
TEDSR0
0x0035
TEDSR1
0x0036
TEDSR2
0x0037
TEDSR3
0x0038
TEDSR4
0x0039
TEDSR5
0x003A
TEDSR6
0x003B
TEDSR7
0x003C
TDLR
NOTE
Read:
• For transmit buffers, anytime when CANTFLG[TXE] flag
is set and the corresponding transmit buffer is selected in
CANTBSEL
• For receive buffers, only when CANRFLG[RXF] flag is set
Write:
• For transmit buffers, anytime when CANTFLG[TXE] flag
is set and the corresponding transmit buffer is selected in
CANTBSEL.
• Unimplemented for receive buffers.
Reset: Undefined because of RAM-based implementation
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
595
Memory map and register definition
MSCAN memory map
Absolute
address
(hex)
Register name
Width
Access
(in bits)
Reset value
Section/
page
4002_4000
MSCAN Control Register 0 (MSCAN_CANCTL0)
8
R/W
01h
32.3.2/598
4002_4001
MSCAN Control Register 1 (MSCAN_CANCTL1)
8
R/W
11h
32.3.3/601
4002_4002
MSCAN Bus Timing Register 0 (MSCAN_CANBTR0)
8
R/W
00h
32.3.4/603
4002_4003
MSCAN Bus Timing Register 1 (MSCAN_CANBTR1)
8
R/W
00h
32.3.5/603
4002_4004
MSCAN Receiver Flag Register (MSCAN_CANRFLG)
8
R/W
00h
32.3.6/605
4002_4005
MSCAN Receiver Interrupt Enable Register
(MSCAN_CANRIER)
8
R/W
00h
32.3.7/607
4002_4006
MSCAN Transmitter Flag Register (MSCAN_CANTFLG)
8
R/W
07h
32.3.8/608
4002_4007
MSCAN Transmitter Interrupt Enable Register
(MSCAN_CANTIER)
8
R/W
00h
32.3.9/609
4002_4008
MSCAN Transmitter Message Abort Request Register
(MSCAN_CANTARQ)
8
R/W
00h
32.3.10/
610
4002_4009
MSCAN Transmitter Message Abort Acknowledge Register
(MSCAN_CANTAAK)
8
R
00h
32.3.11/
611
4002_400A
MSCAN Transmit Buffer Selection Register
(MSCAN_CANTBSEL)
8
R/W
00h
32.3.12/
611
4002_400B
MSCAN Identifier Acceptance Control Register
(MSCAN_CANIDAC)
8
R/W
00h
32.3.13/
613
4002_400D
MSCAN Miscellaneous Register (MSCAN_CANMISC)
8
R/W
00h
32.3.14/
614
4002_400E
MSCAN Receive Error Counter (MSCAN_CANRXERR)
8
R
00h
32.3.15/
614
4002_400F
MSCAN Transmit Error Counter (MSCAN_CANTXERR)
8
R
00h
32.3.16/
615
4002_4010
MSCAN Identifier Acceptance Register n of First Bank
(MSCAN_CANIDAR0)
8
R/W
00h
32.3.17/
615
4002_4011
MSCAN Identifier Acceptance Register n of First Bank
(MSCAN_CANIDAR1)
8
R/W
00h
32.3.17/
615
4002_4012
MSCAN Identifier Acceptance Register n of First Bank
(MSCAN_CANIDAR2)
8
R/W
00h
32.3.17/
615
4002_4013
MSCAN Identifier Acceptance Register n of First Bank
(MSCAN_CANIDAR3)
8
R/W
00h
32.3.17/
615
4002_4014
MSCAN Identifier Mask Register n of First Bank
(MSCAN_CANIDMR0)
8
R/W
00h
32.3.18/
616
4002_4015
MSCAN Identifier Mask Register n of First Bank
(MSCAN_CANIDMR1)
8
R/W
00h
32.3.18/
616
4002_4016
MSCAN Identifier Mask Register n of First Bank
(MSCAN_CANIDMR2)
8
R/W
00h
32.3.18/
616
4002_4017
MSCAN Identifier Mask Register n of First Bank
(MSCAN_CANIDMR3)
8
R/W
00h
32.3.18/
616
4002_4018
MSCAN Identifier Acceptance Register n of Second Bank
(MSCAN_CANIDAR4)
8
R/W
00h
32.3.19/
617
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
596
Freescale Semiconductor, Inc.
Chapter 32 Freescale's Scalable Controller Area Network (MSCAN)
MSCAN memory map (continued)
Absolute
address
(hex)
Register name
Width
Access
(in bits)
Reset value
Section/
page
4002_4019
MSCAN Identifier Acceptance Register n of Second Bank
(MSCAN_CANIDAR5)
8
R/W
00h
32.3.19/
617
4002_401A
MSCAN Identifier Acceptance Register n of Second Bank
(MSCAN_CANIDAR6)
8
R/W
00h
32.3.19/
617
4002_401B
MSCAN Identifier Acceptance Register n of Second Bank
(MSCAN_CANIDAR7)
8
R/W
00h
32.3.19/
617
4002_401C
MSCAN Identifier Mask Register n of Second Bank
(MSCAN_CANIDMR4)
8
R/W
00h
32.3.20/
618
4002_401D
MSCAN Identifier Mask Register n of Second Bank
(MSCAN_CANIDMR5)
8
R/W
00h
32.3.20/
618
4002_401E
MSCAN Identifier Mask Register n of Second Bank
(MSCAN_CANIDMR6)
8
R/W
00h
32.3.20/
618
4002_401F
MSCAN Identifier Mask Register n of Second Bank
(MSCAN_CANIDMR7)
8
R/W
00h
32.3.20/
618
4002_4020
Receive Extended Identifier Register 0 (MSCAN_REIDR0)
8
R/W
Undefined
32.3.21/
618
4002_4020
Receive Standard Identifier Register 0 (MSCAN_RSIDR0)
8
R/W
Undefined
32.3.22/
619
4002_4021
Receive Extended Identifier Register 1 (MSCAN_REIDR1)
8
R/W
Undefined
32.3.23/
619
4002_4021
Receive Standard Identifier Register 1 (MSCAN_RSIDR1)
8
R/W
Undefined
32.3.24/
620
4002_4022
Receive Extended Identifier Register 2 (MSCAN_REIDR2)
8
R/W
Undefined
32.3.25/
621
4002_4023
Receive Extended Identifier Register 3 (MSCAN_REIDR3)
8
R/W
Undefined
32.3.26/
622
4002_4024
Receive Extended Data Segment Register N
(MSCAN_REDSR0)
8
R/W
Undefined
32.3.27/
622
4002_4025
Receive Extended Data Segment Register N
(MSCAN_REDSR1)
8
R/W
Undefined
32.3.27/
622
4002_4026
Receive Extended Data Segment Register N
(MSCAN_REDSR2)
8
R/W
Undefined
32.3.27/
622
4002_4027
Receive Extended Data Segment Register N
(MSCAN_REDSR3)
8
R/W
Undefined
32.3.27/
622
4002_4028
Receive Extended Data Segment Register N
(MSCAN_REDSR4)
8
R/W
Undefined
32.3.27/
622
4002_4029
Receive Extended Data Segment Register N
(MSCAN_REDSR5)
8
R/W
Undefined
32.3.27/
622
4002_402A
Receive Extended Data Segment Register N
(MSCAN_REDSR6)
8
R/W
Undefined
32.3.27/
622
4002_402B
Receive Extended Data Segment Register N
(MSCAN_REDSR7)
8
R/W
Undefined
32.3.27/
622
4002_402C
Receive Data Length Register (MSCAN_RDLR)
8
R/W
Undefined
32.3.28/
623
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
597
Memory map and register definition
MSCAN memory map (continued)
Absolute
address
(hex)
Register name
Width
Access
(in bits)
Reset value
Section/
page
4002_402E
Receive Time Stamp Register High (MSCAN_RTSRH)
8
R
Undefined
32.3.29/
623
4002_402F
Receive Time Stamp Register Low (MSCAN_RTSRL)
8
R
Undefined
32.3.30/
624
4002_4030
Transmit Extended Identifier Register 0 (MSCAN_TEIDR0)
8
R/W
Undefined
32.3.31/
625
4002_4030
Transmit Standard Identifier Register 0 (MSCAN_TSIDR0)
8
R/W
Undefined
32.3.32/
625
4002_4031
Transmit Extended Identifier Register 1 (MSCAN_TEIDR1)
8
R/W
Undefined
32.3.33/
626
4002_4031
Transmit Standard Identifier Register 1 (MSCAN_TSIDR1)
8
R/W
Undefined
32.3.34/
627
4002_4032
Transmit Extended Identifier Register 2 (MSCAN_TEIDR2)
8
R/W
Undefined
32.3.35/
628
4002_4033
Transmit Extended Identifier Register 3 (MSCAN_TEIDR3)
8
R/W
Undefined
32.3.36/
628
4002_4034
Transmit Extended Data Segment Register N
(MSCAN_TEDSR0)
8
R/W
Undefined
32.3.37/
629
4002_4035
Transmit Extended Data Segment Register N
(MSCAN_TEDSR1)
8
R/W
Undefined
32.3.37/
629
4002_4036
Transmit Extended Data Segment Register N
(MSCAN_TEDSR2)
8
R/W
Undefined
32.3.37/
629
4002_4037
Transmit Extended Data Segment Register N
(MSCAN_TEDSR3)
8
R/W
Undefined
32.3.37/
629
4002_4038
Transmit Extended Data Segment Register N
(MSCAN_TEDSR4)
8
R/W
Undefined
32.3.37/
629
4002_4039
Transmit Extended Data Segment Register N
(MSCAN_TEDSR5)
8
R/W
Undefined
32.3.37/
629
4002_403A
Transmit Extended Data Segment Register N
(MSCAN_TEDSR6)
8
R/W
Undefined
32.3.37/
629
4002_403B
Transmit Extended Data Segment Register N
(MSCAN_TEDSR7)
8
R/W
Undefined
32.3.37/
629
4002_403C
Transmit Data Length Register (MSCAN_TDLR)
8
R/W
Undefined
32.3.38/
629
4002_403D
Transmit Buffer Priority Register (MSCAN_TBPR)
8
R/W
Undefined
32.3.39/
630
4002_403E
Transmit Time Stamp Register High (MSCAN_TTSRH)
8
R
Undefined
32.3.40/
631
4002_403F
Transmit Time Stamp Register Low (MSCAN_TTSRL)
8
R
Undefined
32.3.41/
632
32.3.2 MSCAN Control Register 0 (MSCAN_CANCTL0)
The CANCTL0 register provides various control bits of the MSCAN module.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
598
Freescale Semiconductor, Inc.
Chapter 32 Freescale's Scalable Controller Area Network (MSCAN)
NOTE
Write: Anytime when out of initialization mode; exceptions are
read-only RXACT and SYNCH, RXFRM (which is set by the
module only), and INITRQ (which is also writable in
initialization mode)
The CANCTL0 register, except WUPE, INITRQ, and SLPRQ,
is held in the reset state when the initialization mode is active
(INITRQ = 1 and INITAK = 1). This register is writable again
as soon as the initialization mode is exited (INITRQ = 0 and
INITAK = 0).
Address: 4002_4000h base + 0h offset = 4002_4000h
Bit
Read
Write
Reset
7
6
5
RXACT
RXFRM
0
0
CSWAI
0
4
SYNCH
3
2
1
0
TIME
WUPE
SLPRQ
INITRQ
0
0
0
1
0
MSCAN_CANCTL0 field descriptions
Field
7
RXFRM
Description
Received Frame Flag
This bit is read and clear only. It is set when a receiver has received a valid message correctly,
independently of the filter configuration. After it is set, it remains set until cleared by software or reset.
Clearing is done by writing a 1. Writing a 0 is ignored. This bit is not valid in loopback mode.
0
1
6
RXACT
No valid message was received since last clearing this flag.
A valid message was received since last clearing of this flag.
Receiver Active Status
This read-only flag indicates the MSCAN is receiving a message. The flag is controlled by the receiver
front end. This bit is not valid in loopback mode.
NOTE: See the Bosch CAN 2.0A/B specification for a detailed definition of transmitter and receiver
states.
0
1
5
CSWAI
MSCAN is transmitting or idle.
MSCAN is receiving a message, including when arbitration is lost.
CAN Stops in Wait Mode
Enabling this bit allows for lower power consumption in wait mode by disabling all the clocks at the CPU
bus interface to the MSCAN module.
NOTE: In order to protect from accidentally violating the CAN protocol, TXCAN is immediately forced to a
recessive state when the CPU enters wait (CSWAI = 1) or stop mode
0
1
The module is not affected during wait mode.
The module ceases to be clocked during wait mode.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
599
Memory map and register definition
MSCAN_CANCTL0 field descriptions (continued)
Field
4
SYNCH
Description
Synchronized Status
This read-only flag indicates whether the MSCAN is synchronized to the CAN bus and able to participate
in the communication process. It is set and cleared by the MSCAN.
0
1
3
TIME
Timer Enable
This bit activates an internal 16-bit wide free running timer which is clocked by the bit clock rate. If the
timer is enabled, a 16-bit time stamp will be assigned to each transmitted/received message within the
active TX/RX buffer. Right after the EOF of a valid message on the CAN bus, the time stamp is written to
the highest bytes (0x000E, 0x000F) in the appropriate buffer. In loopback mode no receive timestamp is
generated. The internal timer is reset (all bits set to 0) when disabled. This bit is held low in initialization
mode.
0
1
2
WUPE
MSCAN is not synchronized to the CAN bus.
MSCAN is synchronized to the CAN bus.
Disable internal MSCAN timer.
Enable internal MSCAN timer.
WakeUp Enable
This configuration bit allows the MSCAN to restart from sleep mode or from power down mode (entered
from sleep) when traffic on CAN is detected. This bit must be configured before sleep mode entry for the
selected function to take effect.
NOTE: The CPU has to make sure that the WUPE register and the WUPIE wakeup interrupt enable
register is enabled, if the recovery mechanism from stop or wait is required.
0
1
1
SLPRQ
Wakeup disabled - The MSCAN ignores traffic on CAN.
Wakeup enabled - The MSCAN is able to restart.
Sleep Mode Request
This bit requests the MSCAN to enter sleep mode, which is an internal power saving mode. The sleep
mode request is serviced when the CAN bus is idle, i.e., the module is not receiving a message and all
transmit buffers are empty. The module indicates entry to sleep mode by setting SLPAK = 1. SLPRQ
cannot be set while the WUPIF flag is set. Sleep mode will be active until SLPRQ is cleared by the CPU
or, depending on the setting of WUPE, the MSCAN detects activity on the CAN bus and clears SLPRQ
itself.
NOTE: The CPU cannot clear SLPRQ before the MSCAN has entered sleep mode (SLPRQ = 1 and
SLPAK = 1).
0
1
0
INITRQ
Running - The MSCAN functions normally.
Sleep mode request - The MSCAN enters sleep mode when CAN bus idle.
Initialization Mode Request
When this bit is set by the CPU, the MSCAN skips to initialization mode. Any ongoing transmission or
reception is aborted and synchronization to the CAN bus is lost. The module indicates entry to initialization
mode by setting INITAK = 1.
The following registers enter their hard reset state and restore their default values: CANCTL0 (Not
including WUPE, INITRQ, and SLPRQ), CANRFLG (TSTAT1 and TSTAT0 are not affected by initialization
mode), CANRIER (RSTAT1 and RSTAT0 are not affected by initialization mode), CANTFLG, CANTIER,
CANTARQ, CANTAAK, and CANTBSEL. The registers CANCTL1, CANBTR0, CANBTR1, CANIDAC,
CANIDAR0-7, and CANIDMR0-7 can only be written by the CPU when the MSCAN is in initialization mode
(INITRQ = 1 and INITAK = 1). The values of the error counters are not affected by initialization mode.
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
600
Freescale Semiconductor, Inc.
Chapter 32 Freescale's Scalable Controller Area Network (MSCAN)
MSCAN_CANCTL0 field descriptions (continued)
Field
Description
When this bit is cleared by the CPU, the MSCAN restarts and then tries to synchronize to the CAN bus. If
the MSCAN is not in bus-off state, it synchronizes after 11 consecutive recessive bits on the CAN bus; if
the MSCAN is in bus-off state, it continues to wait for 128 occurrences of 11 consecutive recessive bits.
Writing to other bits in CANCTL0, CANRFLG, CANRIER, CANTFLG, or CANTIER must be done only after
initialization mode is exited, which is INITRQ = 0 and INITAK = 0.
NOTE: The CPU cannot clear INITRQ before the MSCAN has entered initialization mode (INITRQ = 1
and INITAK = 1).
In order to protect from accidentally violating the CAN protocol, TXCAN is immediately forced to a
recessive state when the initialization mode is requested by the CPU. Thus, the recommended
procedure is to bring the MSCAN into sleep mode (SLPRQ = 1 and SLPAK = 1) before
requesting initialization mode.
0
1
Normal operation.
MSCAN in initialization mode.
32.3.3 MSCAN Control Register 1 (MSCAN_CANCTL1)
The CANCTL1 register provides various control bits and handshake status information of
the MSCAN module.
NOTE
Write: Anytime in initialization mode (INITRQ = 1 and
INITAK = 1), except CANE which is write once in normal and
anytime in special system operation modes when the MSCAN
is in initialization mode (INITRQ = 1 and INITAK = 1)
Address: 4002_4000h base + 1h offset = 4002_4001h
Bit
Read
Write
Reset
7
6
5
4
3
2
CANE
CLKSRC
LOOPB
LISTEN
BORM
WUPM
0
0
0
1
0
0
1
0
SLPAK
INITAK
0
1
MSCAN_CANCTL1 field descriptions
Field
7
CANE
6
CLKSRC
Description
MSCAN Enable
0
1
MSCAN module is disabled.
MSCAN module is enabled.
MSCAN Clock Source
This bit defines the clock source for the MSCAN module (only for systems with a clock generation
module).
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
601
Memory map and register definition
MSCAN_CANCTL1 field descriptions (continued)
Field
Description
0
1
5
LOOPB
Loopback Self Test Mode
When this bit is set, the MSCAN performs an internal loopback which can be used for self test operation.
The bit stream output of the transmitter is fed back to the receiver internally. The RXCAN input is ignored
and the TXCAN output goes to the recessive state (logic 1). The MSCAN behaves as it does normally
when transmitting and treats its own transmitted message as a message received from a remote node. In
this state, the MSCAN ignores the bit sent during the ACK slot in the CAN frame acknowledge field to
ensure proper reception of its own message. Both transmit and receive interrupts are generated.
0
1
4
LISTEN
This bit configures the MSCAN as a CAN bus monitor. When LISTEN is set, all valid CAN messages with
matching ID are received, but no acknowledgement or error frames are sent out. In addition, the error
counters are frozen. Listen only mode supports applications which require "hot plugging" or throughput
analysis. The MSCAN is unable to transmit any messages when listen only mode is active.
This bit configures the bus-off state recovery mode of the MSCAN.
If WUPE in CANCTL0 is enabled, this bit defines whether the integrated low-pass filter is applied to protect
the MSCAN from spurious wakeup.
MSCAN wakes on any dominant level on the CAN bus.
MSCAN wakes only in case of a dominant pulse on the CAN bus that has a length of Twup.
Sleep Mode Acknowledge
This flag indicates whether the MSCAN module has entered sleep mode. It is used as a handshake flag
for the SLPRQ sleep mode request. Sleep mode is active when SLPRQ = 1 and SLPAK = 1. Depending
on the setting of WUPE, the MSCAN will clear the flag if it detects activity on the CAN bus while in sleep
mode.
0
1
0
INITAK
Automatic bus-off recovery (see Bosch CAN 2.0A/B protocol specification).
Bus-off recovery upon user request.
WakeUp Mode
0
1
1
SLPAK
Normal operation.
Listen only mode activated.
Bus-Off Recovery Mode
0
1
2
WUPM
Loopback self test disabled.
Loopback self test enabled.
Listen Only Mode
0
1
3
BORM
MSCAN clock source is the oscillator clock.
MSCAN clock source is the bus clock.
Running - The MSCAN operates normally.
Sleep mode active - The MSCAN has entered sleep mode.
Initialization Mode Acknowledge
This flag indicates whether the MSCAN module is in initialization mode. It is used as a handshake flag for
the INITRQ initialization mode request. Initialization mode is active when INITRQ = 1 and INITAK = 1. The
registers CANCTL1, CANBTR0, CANBTR1, CANIDAC, CANIDAR0-CANIDAR7, and CANIDMR0CANIDMR7 can be written only by the CPU when the MSCAN is in initialization mode.
0
1
Running - The MSCAN operates normally.
Initialization mode active - The MSCAN has entered initialization mode.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
602
Freescale Semiconductor, Inc.
Chapter 32 Freescale's Scalable Controller Area Network (MSCAN)
32.3.4 MSCAN Bus Timing Register 0 (MSCAN_CANBTR0)
The CANBTR0 register configures various CAN bus timing parameters of the MSCAN
module.
NOTE
Write: Anytime in initialization mode (INITRQ = 1 and
INITAK = 1)
Address: 4002_4000h base + 2h offset = 4002_4002h
Bit
Read
Write
Reset
7
6
5
4
3
SJW
0
2
1
0
0
0
0
BRP
0
0
0
0
MSCAN_CANBTR0 field descriptions
Field
7–6
SJW
Description
Synchronization Jump Width
The synchronization jump width defines the maximum number of time quanta (Tq) clock cycles a bit can
be shortened or lengthened to achieve resynchronization to data transitions on the CAN bus.
00
01
10
11
BRP
1 Tq clock cycle.
2 Tq clock cycles.
3 Tq clock cycle.
4 Tq clock cycles.
Baud Rate Prescaler
These bits determine the time quanta (Tq) clock which is used to build up the bit timing.
000000
000001
000010
000011
111110
111111
1
2
......
......
63
64
32.3.5 MSCAN Bus Timing Register 1 (MSCAN_CANBTR1)
The CANBTR1 register configures various CAN bus timing parameters of the MSCAN
module.
NOTE
Write: Anytime in initialization mode (INITRQ = 1 and
INITAK = 1)
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
603
Memory map and register definition
Address: 4002_4000h base + 3h offset = 4002_4003h
Bit
Read
Write
Reset
7
6
SAMP
5
4
3
2
TSEG2
0
0
0
1
0
0
0
TSEG1
0
0
0
MSCAN_CANBTR1 field descriptions
Field
7
SAMP
Description
Sampling
This bit determines the number of CAN bus samples taken per bit time.
If SAMP = 0, the resulting bit value is equal to the value of the single bit positioned at the sample point. If
SAMP = 1, the resulting bit value is determined by using majority rule on the three total samples. For
higher bit rates, it is recommended that only one sample is taken per bit time (SAMP = 0).
0
1
6–4
TSEG2
One sample per bit.
Three samples per bit. In this case, PHASE_SEG1 must be at least 2 time quanta (Tq).
Time Segment 2
Time segments within the bit time fix the number of clock cycles per bit time and the location of the sample
point.
000
001
010
011
100
101
110
111
TSEG1
1 Tq clock cycle (not valid)
2 Tq clock cycles
3 Tq clock cycles
4 Tq clock cycles
5 Tq clock cycles
6 Tq clock cycles
7 Tq clock cycles
8 Tq clock cycles
Time Segment 1
Time segments within the bit time fix the number of clock cycles per bit time and the location of the sample
point.
The bit time is determined by the oscillator frequency, the baud rate prescaler, and the number of time
quanta (Tq) clock cycles per bit.
Bit time = (1 + timesegment1 + timesegment2) * (Prescaler value)/ fCANCLK
0000
0001
0010
0011
......
1110
1111
1 Tq clock cycle (not valid)
2 Tq clock cycles (not valid)
3 Tq clock cycles (not valid)
4 Tq clock cycles
......
15 Tq clock cycles
16 Tq clock cycles
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
604
Freescale Semiconductor, Inc.
Chapter 32 Freescale's Scalable Controller Area Network (MSCAN)
32.3.6 MSCAN Receiver Flag Register (MSCAN_CANRFLG)
A flag can be cleared only by software (writing a 1 to the corresponding bit position)
when the condition which caused the setting is no longer valid. Every flag has an
associated interrupt enable bit in the CANRIER register.
NOTE
Write: Anytime when not in initialization mode, except
RSTAT[1:0] and TSTAT[1:0] flags which are read-only; write
of 1 clears flag; write of 0 is ignored.
The CANRFLG register is held in the reset state when the
initialization mode is active (INITRQ = 1 and INITAK = 1).
This register is writable again as soon as the initialization mode
is exited (INITRQ = 0 and INITAK = 0).
Address: 4002_4000h base + 4h offset = 4002_4004h
Bit
Read
Write
Reset
7
6
5
WUPIF
CSCIF
0
0
4
3
RSTAT
0
2
TSTAT
0
0
0
1
0
OVRIF
RXF
0
0
MSCAN_CANRFLG field descriptions
Field
7
WUPIF
Description
Wake-Up Interrupt Flag
If the MSCAN detects CAN bus activity while in sleep mode and CANTCTL0[WUPE] = 1, the module will
set WUPIF. If not masked, a wake-up interrupt is pending while this flag is set.
0
1
6
CSCIF
CAN Status Change Interrupt Flag
This flag is set when the MSCAN changes its current CAN bus status due to the actual value of the
transmit error counter (TEC) and the receive error counter (REC). An additional 4-bit (RSTAT[1:0],
TSTAT[1:0]) status register, which is split into separate sections for TEC/REC, informs the system on the
actual CAN bus status. If not masked, an error interrupt is pending while this flag is set. CSCIF provides a
blocking interrupt. That guarantees that the receiver/transmitter status bits (RSTAT/TSTAT) are only
updated when no CAN status change interrupt is pending. If the TECs/RECs change their current value
after the CSCIF is asserted, which would cause an additional state change in the RSTAT/TSTAT bits,
these bits keep their status until the current CSCIF interrupt is cleared again.
0
1
5–4
RSTAT
No wakeup activity observed while in sleep mode.
MSCAN detected activity on the CAN bus and requested wakeup.
No change in CAN bus status occurred since last interrupt.
MSCAN changed current CAN bus status.
Receiver Status
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
605
Memory map and register definition
MSCAN_CANRFLG field descriptions (continued)
Field
Description
The values of the error counters control the actual CAN bus status of the MSCAN. As soon as the status
change interrupt flag (CSCIF) is set, these bits indicate the appropriate receiver related CAN bus status of
the MSCAN.
NOTE: This field is not affected by initialization mode.
00
01
10
11
3–2
TSTAT
RxOK: 0≤receive error counter<96
RxWRN: 96≤receive error counter<128
RxERR: 128≤receive error counter
Bus-off: 256≤transmit error counter (Redundant Information for the most critical CAN bus status
which is "bus-off". This only occurs if the Tx error counter exceeds a number of 255 errors. Bus-off
affects the receiver state. As soon as the transmitter leaves its bus-off state the receiver state skips
to RxOK too. Refer also to TSTAT[1:0] coding in this register. )
Transmitter Status
The values of the error counters control the actual CAN bus status of the MSCAN. As soon as the status
change interrupt flag (CSCIF) is set, these bits indicate the appropriate transmitter related CAN bus status
of the MSCAN.
NOTE: This field is not affected by initialization mode.
00
01
10
11
1
OVRIF
Overrun Interrupt Flag
This flag is set when a data overrun condition occurs. If not masked, an error interrupt is pending while this
flag is set.
0
1
0
RXF
TxOK: 0≤transmit error counter<96
TxWRN: 96≤transmit error counter<128
TxERR: 128≤transmit error counter<256
Bus-off: 256≤transmit error counter
No data overrun condition.
A data overrun detected.
Receive Buffer Full Flag
RXF is set by the MSCAN when a new message is shifted in the receiver FIFO. This flag indicates
whether the shifted buffer is loaded with a correctly received message (matching identifier, matching cyclic
redundancy code (CRC) and no other errors detected). After the CPU has read that message from the
RxFG buffer in the receiver FIFO, the RXF flag must be cleared to release the buffer. A set RXF flag
prohibits the shifting of the next FIFO entry into the foreground buffer (RxFG). If not masked, a receive
interrupt is pending while this flag is set.
NOTE: To ensure data integrity, do not read the receive buffer registers while the RXF flag is cleared.
For MCUs with dual CPUs, reading the receive buffer registers while the RXF flag is cleared may
result in a CPU fault condition.
0
1
No new message available within the RxFG.
The receiver FIFO is not empty. A new message is available in the RxFG.
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
606
Freescale Semiconductor, Inc.
Chapter 32 Freescale's Scalable Controller Area Network (MSCAN)
32.3.7 MSCAN Receiver Interrupt Enable Register
(MSCAN_CANRIER)
This register contains the interrupt enable bits for the interrupt flags described in the
CANRFLG register.
NOTE
The CANRIER register is held in the reset state when the
initialization mode is active (INITRQ=1 and INITAK=1). This
register is writable when not in initialization mode (INITRQ=0
and INITAK=0).
The RSTATE[1:0], TSTATE[1:0] bits are not affected by
initialization mode.
Address: 4002_4000h base + 5h offset = 4002_4005h
Bit
Read
Write
Reset
7
6
5
WUPIE
CSCIE
0
0
4
3
RSTATE
0
2
TSTATE
0
0
0
1
0
OVRIE
RXFIE
0
0
MSCAN_CANRIER field descriptions
Field
7
WUPIE
Description
WakeUp Interrupt Enable
WUPIE and WUPE must both be enabled if the recovery mechanism from stop or wait is required.
0
1
6
CSCIE
5–4
RSTATE
CAN Status Change Interrupt Enable
0
1
No interrupt request is generated from this event.
A CAN Status Change event causes an error interrupt request.
Receiver Status Change Enable
These RSTAT enable bits control the sensitivity level in which receiver state changes are causing CSCIF
interrupts. Independent of the chosen sensitivity level the RSTAT flags continue to indicate the actual
receiver state and are only updated if no CSCIF interrupt is pending.
00
01
10
11
3–2
TSTATE
No interrupt request is generated from this event.
A wake-up event causes a Wake-Up interrupt request.
Do not generate any CSCIF interrupt caused by receiver state changes.
Generate CSCIF interrupt only if the receiver enters or leaves "bus-off" state. Discard other receiver
state changes for generating CSCIF interrupt.
Generate CSCIF interrupt only if the receiver enters or leaves "RxErr" or "bus-off"1 state. Discard
other receiver state changes for generating CSCIF interrupt.
Generate CSCIF interrupt on all state changes.
Transmitter Status Change Enable
Table continues on the next page...
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
Freescale Semiconductor, Inc.
607
Memory map and register definition
MSCAN_CANRIER field descriptions (continued)
Field
Description
These TSTAT enable bits control the sensitivity level in which transmitter state changes are causing
CSCIF interrupts. Independent of the chosen sensitivity level, the TSTAT flags continue to indicate the
actual transmitter state and are only updated if no CSCIF interrupt is pending.
00
01
10
11
Do not generate any CSCIF interrupt caused by transmitter state changes.
Generate CSCIF interrupt only if the transmitter enters or leaves "bus-off" state. Discard other
transmitter state changes for generating CSCIF interrupt.
Generate CSCIF interrupt only if the transmitter enters or leaves "TxErr" or "bus-off" state. Discard
other transmitter state changes for generating CSCIF interrupt.
Generate CSCIF interrupt on all state changes.
1
OVRIE
Overrun Interrupt Enable
0
RXFIE
Receiver Full Interrupt Enable
0
1
0
1
No interrupt request is generated from this event.
An overrun event causes an error interrupt request.
No interrupt request is generated from this event.
A receive buffer full (successful message reception) event causes a receiver interrupt request.
1. Bus-off state is only defined for transmitters by the CAN standard (see Bosch CAN 2.0A/B protocol specification). Because
the only possible state change for the transmitter from bus-off to TxOK also forces the receiver to skip its current state to
RxOK, the coding of the RXSTAT[1:0] flags define an additional bus-off state for the receiver
32.3.8 MSCAN Transmitter Flag Register (MSCAN_CANTFLG)
The transmit buffer empty flags each have an associated interrupt enable bit in the
CANTIER register.
NOTE
Write: Anytime when not in initialization mode; write of 1
clears flag, write of 0 is ignored.
The CANTFLG register is held in the reset state when the
initialization mode is active (INITRQ = 1 and INITAK = 1).
This register is writable when not in initialization mode
(INITRQ = 0 and INITAK = 0).
Address: 4002_4000h base + 6h offset = 4002_4006h
Bit
Read
Write
Reset
7
6
5
4
3
2
1
0
0
0
0
0
TXE
0
0
1
1
1
KE06 Sub-Family Reference Manual, Rev. 2, Feburary 2014
608
Freescale Semiconductor, Inc.
Chapter 32 Freescale's Scalable Controller Area Network (MSCAN)
MSCAN_CANTFLG field descriptions
Field
7–3
Reserved
TXE
Description
This field is reserved.
This read-only field is reserved and always has the value 0.
Transmitter Buffer Empty
This flag indicates that the associated transmit message buffer is empty, and thus not scheduled for
transmission. The CPU must clear the flag after a message is set up in the transmit buffer and is due for
transmission. The MSCAN sets the flag after the message is sent successfully. The flag is also set by the
MSCAN when the transmission request is successfully aborted due to a pending abort request. If not
masked, a transmit interrupt is pending while this flag is set.
Clearing a TXEx flag also clears the corresponding ABTAKx. When a TXEx flag is set, the corresponding
ABTRQx bit is cleared.
When listen-mode is active, the TXEx flags cannot be cleared and no transmission is started.
Read and write accesses to the transmit buffer will be blocked, if the corresponding TXEx bit is cleared
(TXEx = 0) and the buffer is scheduled for transmission.
0
1
The associated message buffer is full (loaded with a me