THE CONNOR-WINFIELD CORP. 2111 COMPREHENSIVE DRIVE. AURORA, IL 60505. FAX (630) 851-5040. PHONE (630) 851-4722. WWW.CONWIN.COM PRODUCT D ATA SHEET CRYSTAL CONTROLLED OSCILLATORS 14 PIN DIP 5.0V SINEWAVE OCVCXO ABSOLUTE M AXIMUM RATING S PARAMETER UNITS MINIMUM NOMINAL MAXIMUM UNITS -55 - 125 °C Storage Temperature NOTE Supply Voltage (Vcc) -0.5 - 7.0 Vdc Control Voltage (Vc) -0.5 - 7.0 Vdc MINIMUM NOMINAL MAXIMUM UNITS 6.4 - 25 1.5 MHz ppm 1, 4 OPERATING SPECIFIC ATIONS OVA5AB1BA TABLE 2.0 PARAMETER Center Frequency (Fo) Frequency Calibration -1.5 Frequency Stability NOTE DESCRIPTION - - 0.25 ppm 2 -0.05 - 0.05 ppm 3 Aging (Daily -30 - 30 ppb 4 Aging (20 years) Total Frequency Tolerance Operating Temperature Range -2.5 -4.6 0 - 2.5 4.6 70 ppm ppm °C 5 Frequency vs. Change in Supply Voltage Supply Voltage (Vcc) 4.75 5.00 5.25 Vdc Supply Current Steady State Supply Current @ 25°C Phase Jitter (BW =10KHz to Fo/2) Phase Jitter (BW =10Hz to Fo/2) Period Jitter Start-Up Time: Oscillator Warm Up Time TDEV at 1.0 seconds TDEV at 4.0 seconds (Icc) - 150 - 300 1 3 3 35 5 1 2 mA mA ps RMS ps RMS ps RMS ms Minutes ns ns INPUT CHARACTERISTICS The Connor-Winfield OVA5AB1BA is a hermetically sealed 14 Pin DIP, 5.0V Voltage Controlled Oven Stabilized Crystal Oscillator (OCVCXO) with a Sinewave output. The OVA5AB1BA is designed for applications requiring low jitter and tight frequency stability. 6 FEATURES TABLE 3.0 PARAMETER Control Voltage Range Frequency at Vc=0.5 Vdc Frequency at Vc=4.1 Vdc Slope of Frequency Adjust Input Impedance CW 0650 OVA5AB1BA 10MHz TABLE 1.0 MINIMUM 0.5 5 2.8 100k NOMINAL 2.0 PARAMETER LOAD Output Power Spurious Output SSB Phase Noise at 1Hz offset SSB Phase Noise at 10Hz offset SSB Phase Noise at 100Hz offset MINIMUM 45 0 NOMINAL 50 3 - SSB Phase Noise at 1KHz offset SSB Phase Noise at 10KHz offset (Vc) MAXIMUM 4.1 -5 - UNITS Vdc ppm ppm ppm/V Ohm -60 -90 -120 MAXIMUM 55 -80 - UNITS Ohms dBm dBc dBc/Hz dBc/Hz dBc/Hz - -140 - dBc/Hz - -150 - dBc/Hz - SINEWAVE OUTPUT CHARACTERISTICS 7 7 TABLE 4.0 PACKAGE CHARACTERISTICS Package NOTE NOTE 5.0V OPERATION OCVCXO SINEWAVE OUTPUT LOW JITTER <1pS RMS FREQUENCY STABILITY: 0.25ppm ABSOLUTE TOTAL FREQUENCY TOLERANCE: ±4.6ppm OVER TWENTY YEARS TEMPERATURE RANGE: 0 to 70°C HERMETICALLY SEALED 14 PIN DIP PACKAGE RoHS COMPLIANT / LEAD FREE ORDERING INFORMATION OVA5AB1BA OCXO SERIES - 10MHz CENTER FREQUENCY TABLE 5.0 14 pin DIP, hermetically sealed, welded package. Specifications subject to change without notice. DATA SHEET #: Cx116 PAGE 1 OF 2 REV: 00 DATE: 12/29/06 aCopyright 2001 Connor-Winfield all rights reserved. THE CONNOR-WINFIELD CORP. 2111 COMPREHENSIVE DRIVE. AURORA, IL 60505. FAX (630) 851-5040. PHONE (630) 851-4722. WWW.CONWIN.COM PRODUCT D ATA SHEET CRYSTAL CONTROLLED OSCILLATORS Notes: 1) 2) 3) 4) 5) Initial calibration @ 25°C, Vc = 2.0 Vdc. Frequency stability, absolute over the temperature range of 0 to 70°C. Frequency stability per 5% change in supply voltage. At the time of shipment after 48 hours of operation. Inclusive of calibration, operating tem perature range, supply voltage change, s hock and vibration and aging (20 years). 6) Measured @ 25°C, within 5 minutes, the unit will be within +/-0.1ppm of its reference frequency, measured after 30 minutes of c ontinuous operation at a stable 25 °C. 7) Referenced to Fo @ 25°C, Positive Transfer Characteristic. Package Layout Pin Connections TABLE 6.0 Pin 1 7 8 14 Function Voltage Control Ground (Case) Output Vcc Dimensional Tolerance: ±.005 (.127mm) Solder Profile Test Circuit Temperature 260°C 260°C 220°C 180°C 150°C 120°C 0 CONTROL VOLTAGE DATA SHEET #: 50 Ohm Oscilloscope Termination 120 S Max. Time 10 S 60 S Max. 360 Sec. Max. ENVIRONMENTAL CHARACTERISTICS Temperature Cycle: Per MIL-STD-883, Method 1010, Condition B. -55°C to 125°C, 300 cycles, 10 minute dwell, 1minute transition. Gross Leak Test: Per MIL-STD-202, Method 112, Condition D. No Bubbles i n flourinert (FC-43) at 125°C ±5°C for 20 seconds. SOLDERING Pin Solderability: Per MIL-STD-883, Method 2003. 8 hour steam age prior to 2 54°C ±5°C Solder pot dip, 95% Coverage. Resistance to Solder Heat: Per MIL-STD-202, Method 210, Condition C. Wave: Topside boardmount product, 260°C ±5°C for 20 seconds. MECHANICAL CHARACTERISTICS Vibration: Per MIL-STD-202, Method 204, Condition A. 10G’s peak , 10Hz to 500Hz, 15 minute cycles 12 times each perpendicular ax is. Shock: Per MIL-STD-202, Method 213, Condition F. 1500G’s, 0.5m s, half sine, 3 shocks per direction. Moisture Resistance: Per MIL-STD-202, Method 106. 95% RH @ 65°C, 10 c ycles 10°C to 65°C. Specifications subject to change without notice. Cx116 PAGE 2 OF 2 REV: 00 aCopyright 2001 Connor-Winfield all rights reserved. DATE: 12/29/06