MB9A310K Series
32-bit ARM® Cortex®-M3
FM3 Microcontroller
The MB9A310K Series are a highly integrated 32-bit microcontrollers dedicated for embedded controllers with high-performance
and low cost.
®
®
These series are based on the ARM Cortex -M3 Processor with on-chip Flash memory and SRAM, and has peripheral functions
2
such as Motor Control Timers, ADCs and Communication Interfaces (USB, UART, CSIO, I C, LIN).
The products which are described in this Datasheet are placed into TYPE5 product categories in "FM3 Family Peripheral Manual".
Features
32-bit ARM Cortex-M3 Core
[USB function]
Processor version: r2p1
USB2.0 Full-Speed supported
Up to 40MHz Frequency Operation
Max 6 EndPoint supported
Integrated Nested Vectored Interrupt Controller (NVIC) : 1
NMI (non-maskable interrupt) and 48 peripheral interrupts
and 16 priority levels
24-bit System timer (Sys Tick) : System timer for OS task
management
On-chip Memories
EndPoint
0 is control transfer
1, 2 can be selected Bulk-transfer,
Interrupt-transfer or Isochronous-transfer
EndPoint 3 to 5 can be selected Bulk-transfer or
Interrupt-transfer
EndPoint 1 to 5 is comprised Double Buffer
The size of each EndPoint is as follows.
• EndPoint 0, 2 to 5:64 bytes
• EndPoint 1: 256 bytes
EndPoint
[Flash memory]
This Series are based on two independent on-chip Flash
memories.
MainFlash
[USB host]
USB2.0 Full/Low-speed supported
Bulk-transfer, interrupt-transfer and Isochronous-transfer
Up
to 128Kbyte
Read cycle : 0 wait-cycle
Security function for code protection
support
USB Device connected/dis-connected automatically detect
IN/OUT token handshake packet automatically
WorkFlash
32Kbyte
Read
cycle : 0 wait-cycle
Security function is shared with code protection
Max 256-byte packet-length supported
Wake-up function supported
[SRAM]
Multi-function Serial Interface (Max 4channels)
This Series contain a total of up to 16Kbyte on-chip SRAM.
This is composed of two independent SRAM (SRAM0,
SRAM1) . SRAM0 is connected to I-code bus and D-code bus
of Cortex-M3 core. SRAM1 is connected to System bus.
2 channels with 16-steps × 9-bits FIFO (ch.0, ch.1), 2
SRAM0 : 8 Kbyte
SRAM1 : 8 Kbyte
USB Interface
USB interface is composed of Function and Host.
PLL for USB is built-in, USB clock can be generated by
multiplication of Main clock.
Cypress Semiconductor Corporation
Document Number: 002-05625 Rev.*A
•
channels without FIFO (ch.3, ch.5)
Operation mode is selectable from the followings for each
channel.
(In ch.5, only UART and LIN are available.)
UART
CSIO
LIN
2
I C
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised April 26, 2016
MB9A310K Series
[UART]
Full-duplex double buffer
Selection with or without parity supported
Built-in dedicated baud rate generator
External clock available as a serial clock
Hardware Flow control : Automatically control the
transmission by CTS/RTS (only ch.4)
Various error detect functions available (parity errors, framing
errors, and overrun errors)
[CSIO]
Full-duplex double buffer
Built-in dedicated baud rate generator
Overrun error detect function available
A/D Converter (Max 8channels)
[12-bit A/D Converter]
Successive Approximation Register type
Built-in 2unit
Conversion time: 1.0μs@5V
Priority conversion available (priority at 2levels)
Scanning conversion mode
Built-in FIFO for conversion data storage
(for SCAN conversion: 16steps, for Priority conversion:
4steps)
Base Timer (Max 8channels)
Operation mode is selectable from the followings for each
channel.
16-bit PWM timer
[LIN]
16-bit PPG timer
LIN protocol Rev.2.1 supported
16/32-bit reload timer
Full-duplex double buffer
16/32-bit PWC timer
Master/Slave mode supported
LIN break field generate (can be changed 13 to 16-bit length)
LIN break delimiter generate (can be changed 1 to 4-bit
length)
Various error detect functions available (parity errors, framing
General Purpose I/O Port
This series can use its pins as General Purpose I/O ports when
they are not used for external bus or peripherals. Moreover, the
port relocate function is built in. It can set which I/O port the
peripheral function can be allocated.
errors, and overrun errors)
Capable of pull-up control per pin
2
Capable of reading pin level directly
[I C]
Standard mode (Max 100kbps) / Fast-mode (Max 400kbps)
supported
DMA Controller (4channels)
DMA Controller has an independent bus for CPU, so CPU and
DMA Controller can process simultaneously.
Built-in the port relocate function
Up 36 fast General Purpose I/O Ports
Some pin is 5V tolerant I/O.
See "Pin Description" to confirm the corresponding pins.
Multi-function Timer
8 independently configured and operated channels
The Multi-function timer is composed of the following blocks.
Transfer can be started by software or request from the
16-bit free-run timer × 3ch.
built-in peripherals
Transfer address area: 32-bit (4Gbyte)
Transfer mode: Block transfer/Burst transfer/Demand
transfer
Input capture × 4ch.
Output compare × 6ch.
A/D activating compare × 3ch.
Transfer data type: byte/half-word/word
Waveform generator × 3ch.
Transfer block count: 1 to 16
16-bit PPG timer × 3ch.
Number of transfers: 1 to 65536
The following function can be used to achieve the motor
control.
PWM signal output function
DC chopper waveform output function
Dead time function
Input capture function
Document Number: 002-05625 Rev.*A
Page 2 of 87
MB9A310K Series
A/D convertor activate function
CRC (Cyclic Redundancy Check) Accelerator
DTIF (Motor emergency stop) interrupt function
The CRC accelerator helps a verify data transmission or
storage integrity.
Real-time clock (RTC)
CCITT CRC16 and IEEE-802.3 CRC32 are supported.
The Real-time clock can count
Year/Month/Day/Hour/Minute/Second/A day of the week from
01 to 99.
CCITT CRC16 Generator Polynomial: 0x1021
Interrupt function with specifying date and time
(Year/Month/Day/Hour/Minute/Second/A day of the week.) is
available. This function is also available by specifying only
Year, Month, Day, Hour or Minute.
Timer interrupt function after set time or each set time.
Capable of rewriting the time with continuing the time count.
Leap year automatic count is available.
IEEE-802.3 CRC32 Generator Polynomial: 0x04C11DB7
Clock and Reset
[Clocks]
Five clock sources (2 external oscillators, 2 internal CR
oscillator, and Main PLL) that are dynamically selectable.
Main Clock
: 4MHz to 48MHz
Sub Clock
: 32.768kHz
Quadrature Position/Revolution Counter (QPRC)
High-speed internal CR Clock: 4MHz
The Quadrature Position/Revolution Counter (QPRC) is used
to measure the position of the position encoder. Moreover, it is
possible to use up/down counter.
Low-speed internal CR Clock : 100kHz
The detection edge of the three external event input pins AIN,
BIN and ZIN is configurable.
Main PLL Clock
[Resets]
16-bit position counter
Reset requests from INITX pin
16-bit revolution counter
Power on reset
Two 16-bit compare registers
Software reset
Watchdog timers reset
Dual Timer (32/16-bit Down Counter)
The Dual Timer consists of two programmable 32/16-bit down
counters.
Operation mode is selectable from the followings for each
channel.
Free-running
Periodic ( = Reload)
One-shot
Watch Counter
The Watch counter is used for wake up from Low Power
Consumption mode.
Interval timer: up to 64s (Max) @ Sub Clock : 32.768kHz
Low-voltage detector reset
Clock supervisor reset
Clock Super Visor (CSV)
Clocks generated by internal CR oscillators are used to
supervise abnormality of the external clocks.
External OSC clock failure (clock stop) is detected, reset is
asserted.
External OSC frequency anomaly is detected, interrupt or
reset is asserted.
Low-Voltage Detector (LVD)
External Interrupt Controller Unit
This Series include 2-stage monitoring of voltage on the VCC
pins. When the voltage falls below the voltage has been set,
Low-Voltage Detector generates an interrupt or reset.
Up to 6 external interrupt input pin
LVD1: error reporting via interrupt
Include one non-maskable interrupt (NMI)
LVD2: auto-reset operation
Watchdog Timer (2channels)
A watchdog timer can generate interrupts or a reset when a
time-out value is reached.
This series consists of two different watchdogs, a "Hardware"
watchdog and a "Software" watchdog.
"Hardware" watchdog timer is clocked by low-speed internal
CR oscillator. Therefore, ”Hardware" watchdog is active in any
power saving mode except RTC and STOP and Deep stand-by
RTC and Deep stand-by STOP.
Document Number: 002-05625 Rev.*A
Page 3 of 87
MB9A310K Series
Low Power Consumption Mode
Power Supply
Six Low Power Consumption modes supported.
Wide range voltage: VCC
SLEEP
TIMER
RTC
= 2.7V to 5.5V
Power supply for USB I/O: USBVCC0
= 3.0V to 3.6V (when USB is used)
= 2.7V to 5.5V (when GPIO is used)
STOP
Deep stand-by RTC
Deep stand-by STOP
Debug
Serial Wire JTAG Debug Port (SWJ-DP)
Document Number: 002-05625 Rev.*A
Page 4 of 87
MB9A310K Series
Contents
1.
Product Lineup ........................................................................................................................................................... 7
2.
Packages
............................................................................................................................................................. 8
3.
Pin Assignment .......................................................................................................................................................... 9
4.
List of Pin Functions ................................................................................................................................................ 12
5.
I/O Circuit Type ......................................................................................................................................................... 21
6.
Handling Precautions .............................................................................................................................................. 26
6.1
Precautions for Product Design.................................................................................................................................. 26
6.2
Precautions for Package Mounting ............................................................................................................................ 27
6.3
Precautions for Use Environment ............................................................................................................................... 28
7.
Handling Devices ..................................................................................................................................................... 29
8.
Block Diagram .......................................................................................................................................................... 32
9.
Memory Size ........................................................................................................................................................... 32
10.
Memory Map ........................................................................................................................................................... 33
11.
Pin Status in Each CPU State.................................................................................................................................. 36
12.
Electrical Characteristics ........................................................................................................................................ 42
12.1
Absolute Maximum Ratings........................................................................................................................................ 42
12.2
Recommended Operating Conditions ........................................................................................................................ 44
12.3
DC Characteristics ..................................................................................................................................................... 45
12.3.1 Current Rating ............................................................................................................................................................ 45
12.3.2 Pin Characteristics ..................................................................................................................................................... 48
12.4
AC Characteristics ..................................................................................................................................................... 49
12.4.1 Main Clock Input Characteristics ................................................................................................................................ 49
12.4.2 Sub Clock Input Characteristics ................................................................................................................................. 50
12.4.3 Internal CR Oscillation Characteristics ....................................................................................................................... 50
12.4.4 Operating Conditions of Main and USB PLL (In the case of using main clock for input of PLL .................................. 51
12.4.5 Operating Conditions of Main PLL (In the case of using high-speed internal CR)...................................................... 51
12.4.6 Reset Input Characteristics ........................................................................................................................................ 52
12.4.7 Power-on Reset Timing .............................................................................................................................................. 52
12.4.8 Base Timer Input Timing ............................................................................................................................................ 53
12.4.9 CSIO/UART Timing .................................................................................................................................................... 54
12.4.10 External Input Timing ................................................................................................................................................. 62
12.4.11 Quadrature Position/Revolution Counter timing ......................................................................................................... 63
2
12.4.12 I C Timing .................................................................................................................................................................. 65
12.4.13 JTAG Timing .............................................................................................................................................................. 66
12.5
12-bit A/D Converter .................................................................................................................................................. 67
12.6
USB Characteristics ................................................................................................................................................... 70
12.7
Low-voltage Detection Characteristics ....................................................................................................................... 74
12.7.1 Low-voltage Detection Reset ..................................................................................................................................... 74
12.7.2 Interrupt of Low-voltage Detection ............................................................................................................................. 74
12.8
MainFlash Memory Write/Erase Characteristics ........................................................................................................ 75
12.8.1 Write / Erase time....................................................................................................................................................... 75
12.8.2 Erase/write cycles and data hold time ........................................................................................................................ 75
12.9
WorkFlash Memory Write/Erase Characteristics ........................................................................................................ 75
12.9.1 Write / Erase time....................................................................................................................................................... 75
12.9.2 Erase/write cycles and data hold time ........................................................................................................................ 75
Document Number: 002-05625 Rev.*A
Page 5 of 87
MB9A310K Series
12.10 Return Time from Low-Power Consumption Mode .................................................................................................... 76
12.10.1 Return Factor: Interrupt/WKUP .................................................................................................................................. 76
12.11 Return Factor: Reset .................................................................................................................................................. 78
12.11.1 Return Count Time ..................................................................................................................................................... 78
13.
Ordering Information ............................................................................................................................................... 80
14.
Package Dimensions ............................................................................................................................................... 81
15.
Major Changes ......................................................................................................................................................... 84
16.
Document History .................................................................................................................................................... 86
Document Number: 002-05625 Rev.*A
Page 6 of 87
MB9A310K Series
1. Product Lineup
Memory size
Product name
On-chip
Flash memory
MB9AF311K
MB9AF312K
MainFlash
64 Kbyte
128 Kbyte
WorkFlash
32 Kbyte
32 Kbyte
SRAM0
8 Kbyte
8 Kbyte
On-chip SRAM
SRAM1
8 Kbyte
8 Kbyte
Total
16 Kbyte
16 Kbyte
Function
MB9AF311K
MB9AF312K
Product name
Pin count
CPU
Freq.
Power supply voltage range
USB2.0 (Function/Host)
DMAC
Multi-function Serial Interface
(UART/CSIO/LIN/I2C)
Base Timer
(PWC/ Reload timer/PWM/PPG)
A/D activation
3ch.
compare
Input capture
4ch.
Free-run timer
3ch.
MFOutput
Timer
6ch.
compare
Waveform
3ch.
generator
PPG
3ch.
QPRC
Dual Timer
Real-time clock
Watch Counter
CRC Accelerator
Watchdog timer
External Interrupts
General Purpose I/O ports
12-bit A/D converter
CSV (Clock Super Visor)
LVD (Low-Voltage Detector)
High-speed
Built-in OSC
Low-speed
Debug Function
Note:
48/52
Cortex-M3
40 MHz
2.7V to 5.5V
(USBVCC:3.0V to 3.6V)
1ch. (Max)
4ch. (Max)
4ch. (Max)
with 16-steps × 9-bits FIFO : ch.0, ch.1
without FIFO : ch.3, ch.5 (In ch.5, only UART and LIN are available.)
8ch. (Max)
1 unit (Max)
1ch. (Max)
1 unit
1 unit
1 unit
Yes
1ch. (SW) + 1ch. (HW)
6 pins (Max) + NMI × 1
36 pins (Max)
8ch. (2 units)
Yes
2ch.
4 MHz
100 kHz
SWJ-DP
All signals of the peripheral function in each product cannot be allocated by limiting the pins of package. It is necessary to
use the port relocate function of the General I/O port according to your function use.
See "12. Electrical Characteristics 12.4. AC Characteristics" for accuracy of built-in CR.
Document Number: 002-05625 Rev.*A
Page 7 of 87
MB9A310K Series
2. Packages
Product name
Package
MB9AF311K
MB9AF312K
LQFP:
FPT-48P-M49 (0.5mm pitch)
QFN:
LCC-48P-M73 (0.5mm pitch)
LQFP:
FPT-52P-M02 (0.65mm pitch)
: Supported
Note: See "14.Package Dimensions" for detailed information on each package.
Document Number: 002-05625 Rev.*A
Page 8 of 87
MB9A310K Series
3. Pin Assignment
FPT-48P-M49
VSS
P81/UDP0
P80/UDM0
USBVCC
P60/SIN5_0/TIOA2_2/INT15_1/IC00_0/WKUP3
P61/SOT5_0/TIOB2_2/UHCONX/DTTI0X_2
P0F/NMIX/CROUT_1/RTCCO_0/SUBOUT_0/WKUP0
P04/TDO/SWO
P03/TMS/SWDIO
P02/TDI
P01/TCK/SWCLK
P00/TRSTX
48
47
46
45
44
43
42
41
40
39
38
37
(TOP VIEW)
VCC
1
36
P21/SIN0_0/INT06_1/WKUP2
P50/INT00_0/AIN0_2/SIN3_1
2
35
P22/AN07/SOT0_0/TIOB7_1
P51/INT01_0/BIN0_2/SOT3_1
3
34
P23/AN06/SCK0_0/TIOA7_1
P52/INT02_0/ZIN0_2/SCK3_1
4
33
AVSS
P39/DTTI0X_0/ADTG_2
5
32
AVRH
P3A/RTO00_0/TIOA0_1/RTCCO_2/SUBOUT_2
6
31
AVCC
P3B/RTO01_0/TIOA1_1
7
30
P15/AN05/SOT0_1/IC03_2
P3C/RTO02_0/TIOA2_1
8
29
P14/AN04/SIN0_1/INT03_1/IC02_2
P3D/RTO03_0/TIOA3_1
9
28
P13/AN03/SCK1_1/IC01_2/RTCCO_1/SUBOUT_1
P3E/RTO04_0/TIOA4_1
10
27
P12/AN02/SOT1_1/IC00_2
P3F/RTO05_0/TIOA5_1
11
26
P11/AN01/SIN1_1/INT02_1/FRCK0_2/IC02_0/WKUP1
VSS
12
25
P10/AN00
13
14
15
16
17
18
19
20
21
22
23
24
C
VCC
P46/X0A
P47/X1A
INITX
P49/TIOB0_0
P4A/TIOB1_0
PE0/MD1
MD0
PE2/X0
PE3/X1
VSS
LQFP - 48
Note :
The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these
pins, there are multiple pins that provide the same function for the same channel. Use the extended port function register (EPFR)
to select the pin.
Document Number: 002-05625 Rev.*A
Page 9 of 87
MB9A310K Series
LCC-48P-M73
VSS
P81/UDP0
P80/UDM0
USBVCC
P60/SIN5_0/TIOA2_2/INT15_1/IC00_0/WKUP3
P61/SOT5_0/TIOB2_2/UHCONX/DTTI0X_2
P0F/NMIX/CROUT_1/RTCCO_0/SUBOUT_0/WKUP0
P04/TDO/SWO
P03/TMS/SWDIO
P02/TDI
P01/TCK/SWCLK
P00/TRSTX
48
47
46
45
44
43
42
41
40
39
38
37
(TOP VIEW)
VCC
1
36
P21/SIN0_0/INT06_1/WKUP2
P50/INT00_0/AIN0_2/SIN3_1
2
35
P22/AN07/SOT0_0/TIOB7_1
P51/INT01_0/BIN0_2/SOT3_1
3
34
P23/AN06/SCK0_0/TIOA7_1
P52/INT02_0/ZIN0_2/SCK3_1
4
33
AVSS
P39/DTTI0X_0/ADTG_2
5
32
AVRH
P3A/RTO00_0/TIOA0_1/RTCCO_2/SUBOUT_2
6
31
AVCC
P3B/RTO01_0/TIOA1_1
7
30
P15/AN05/SOT0_1/IC03_2
P3C/RTO02_0/TIOA2_1
8
29
P14/AN04/SIN0_1/INT03_1/IC02_2
P3D/RTO03_0/TIOA3_1
9
28
P13/AN03/SCK1_1/IC01_2/RTCCO_1/SUBOUT_1
P3E/RTO04_0/TIOA4_1
10
27
P12/AN02/SOT1_1/IC00_2
P3F/RTO05_0/TIOA5_1
11
26
P11/AN01/SIN1_1/INT02_1/FRCK0_2/IC02_0/WKUP1
VSS
12
25
P10/AN00
13
14
15
16
17
18
19
20
21
22
23
24
C
VCC
P46/X0A
P47/X1A
INITX
P49/TIOB0_0
P4A/TIOB1_0
PE0/MD1
MD0
PE2/X0
PE3/X1
VSS
QFN - 48
Note
The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these
pins, there are multiple pins that provide the same function for the same channel. Use the extended port function register (EPFR)
to select the pin.
Document Number: 002-05625 Rev.*A
Page 10 of 87
MB9A310K Series
FPT-52P-M02
VSS
P81/UDP0
P80/UDM0
USBVCC
P60/SIN5_0/TIOA2_2/INT15_1/IC00_0/WKUP3
P61/SOT5_0/TIOB2_2/UHCONX/DTTI0X_2
P0F/NMIX/CROUT_1/RTCCO_0/SUBOUT_0/WKUP0
P04/TDO/SWO
P03/TMS/SWDIO
P02/TDI
P01/TCK/SWCLK
P00/TRSTX
NC
52
51
50
49
48
47
46
45
44
43
42
41
40
(TOP VIEW)
VCC
1
39
P21/SIN0_0/INT06_1/WKUP2
P50/INT00_0/AIN0_2/SIN3_1
2
38
P22/AN07/SOT0_0/TIOB7_1
P51/INT01_0/BIN0_2/SOT3_1
3
37
P23/AN06/SCK0_0/TIOA7_1
P52/INT02_0/ZIN0_2/SCK3_1
4
36
NC
NC
5
35
AVSS
P39/DTTI0X_0/ADTG_2
6
34
AVRH
P3A/RTO00_0/TIOA0_1/RTCCO_2/SUBOUT_2
7
33
AVCC
P3B/RTO01_0/TIOA1_1
8
32
P15/AN05/SOT0_1/IC03_2
P3C/RTO02_0/TIOA2_1
9
31
P14/AN04/SIN0_1/INT03_1/IC02_2
P3D/RTO03_0/TIOA3_1
10
30
P13/AN03/SCK1_1/IC01_2/RTCCO_1/SUBOUT_1
P3E/RTO04_0/TIOA4_1
11
29
P12/AN02/SOT1_1/IC00_2
P3F/RTO05_0/TIOA5_1
12
28
P11/AN01/SIN1_1/INT02_1/FRCK0_2/IC02_0/WKUP1
VSS
13
27
P10/AN00
14
15
16
17
18
19
20
21
22
23
24
25
26
C
VCC
P46/X0A
P47/X1A
INITX
P49/TIOB0_0
P4A/TIOB1_0
NC
PE0/MD1
MD0
PE2/X0
PE3/X1
VSS
LQFP - 52
Note
The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these pins,
there are multiple pins that provide the same function for the same channel. Use the extended port function register (EPFR) to
select the pin.
Document Number: 002-05625 Rev.*A
Page 11 of 87
MB9A310K Series
4. List of Pin Functions
List of pin numbers
The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these pins,
there are multiple pins that provide the same function for the same channel. Use the extended port function register (EPFR) to
select the pin.
Pin No
LQFP-48
QFN-48
LQFP-52
1
1
Pin Name
I/O circuit
type
VCC
Pin state
type
-
P50
2
2
INT00_0
AIN0_2
I[1]
H
I[1]
H
I[1]
H
SIN3_1
P51
3
3
INT01_0
BIN0_2
SOT3_1
P52
INT02_0
4
4
-
5
NC
5
6
DTTI0X_0
ZIN0_2
SCK3_1
-
P39
E
I
G
I
G
I
G
I
G
I
G
I
G
I
ADTG_2
P3A
RTO00_0
6
7
TIOA0_1
RTCCO_2
SUBOUT_2
P3B
7
8
RTO01_0
TIOA1_1
P3C
8
9
RTO02_0
TIOA2_1
P3D
9
10
RTO03_0
TIOA3_1
P3E
10
11
RTO04_0
TIOA4_1
P3F
11
12
RTO05_0
TIOA5_1
Document Number: 002-05625 Rev.*A
Page 12 of 87
MB9A310K Series
Pin No
LQFP-48
QFN-48
LQFP-52
12
13
13
14
15
16
16
17
17
18
18
19
19
20
-
21
20
22
21
23
22
24
23
25
24
26
25
27
Pin Name
I/O circuit
type
Pin state
type
VSS
-
14
C
-
15
VCC
-
P46
X0A
P47
X1A
INITX
P49
TIOB0_0
P4A
TIOB1_0
D
M
D
N
B
C
E
I
E
I
NC
PE0
MD1
MD0
PE2
X0
PE3
X1
C
P
J
D
A
A
A
B
VSS
P10
AN00
F
K
F
F
F
K
F
K
P11
AN01
SIN1_1
26
28
INT02_1
FRCK0_2
IC02_0
WKUP1
P12
27
29
AN02
SOT1_1
IC00_2
P13
AN03
28
30
SCK1_1
IC01_2
RTCCO_1
SUBOUT_1
Document Number: 002-05625 Rev.*A
Page 13 of 87
MB9A310K Series
Pin No
LQFP-48
QFN-48
LQFP-52
Pin Name
I/O circuit
type
Pin state
type
F
L
F
K
P14
AN04
29
31
SIN0_1
INT03_1
IC02_2
30
32
31
32
33
-
33
34
35
36
34
37
35
38
36
39
-
40
37
41
38
42
39
43
40
44
41
45
42
46
Document Number: 002-05625 Rev.*A
P15
AN05
SOT0_1
IC03_2
AVCC
AVRH
AVSS
NC
P23
AN06
SCK0_0
TIOA7_1
P22
AN07
SOT0_0
TIOB7_1
P21
SIN0_0
INT06_1
WKUP2
NC
P00
TRSTX
P01
TCK
SWCLK
P02
TDI
P03
TMS
SWDIO
P04
TDO
SWO
P0F
NMIX
CROUT_1
RTCCO_0
SUBOUT_0
WKUP0
-
F
K
F
K
E
G
E
E
E
E
E
E
E
E
E
E
E
J
Page 14 of 87
MB9A310K Series
Pin No
LQFP-48
QFN-48
LQFP-52
43
47
44
48
45
49
46
50
47
51
48
52
Pin Name
P61
SOT5_0
TIOB2_2
UHCONX
DTTI0X_2
P60
SIN5_0
TIOA2_2
INT15_1
IC00_0
WKUP3
USBVCC
P80
UDM0
P81
UDP0
VSS
I/O circuit
type
Pin state
Type
E
I
I[1]
G
H
O
H
O
-
[1]: 5V tolerant I/O
Document Number: 002-05625 Rev.*A
Page 15 of 87
MB9A310K Series
List of pin functions
The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these pins,
there are multiple pins that provide the same function for the same channel. Use the extended port function register (EPFR) to
select the pin.
Module
Pin name
ADC
ADTG_2
AN00
AN01
AN02
AN03
AN04
AN05
AN06
AN07
TIOA0_1
TIOB0_0
TIOA1_1
TIOB1_0
TIOA2_1
TIOA2_2
TIOB2_2
A/D converter external trigger input pin
Base Timer
0
Base Timer
1
Base Timer
2
Base Timer
3
Base Timer
4
Base Timer
5
Base Timer
7
Debugger
External
Interrupt
Function
Pin No
LQFP-48
LQFP-52
QFN-48
Base timer ch.2 TIOB pin
5
25
26
27
28
29
30
34
35
6
18
7
19
8
44
43
6
27
28
29
30
31
32
37
38
7
19
8
20
9
48
47
TIOA3_1
Base timer ch.3 TIOA pin
9
10
TIOA4_1
Base timer ch.4 TIOA pin
10
11
TIOA5_1
Base timer ch.5 TIOA pin
11
12
TIOA7_1
TIOB7_1
SWCLK
SWDIO
SWO
TCK
TDI
TDO
TMS
TRSTX
INT00_0
INT01_0
INT02_0
INT02_1
INT03_1
INT06_1
INT15_1
NMIX
Base timer ch.7 TIOA pin
Base timer ch.7 TIOB pin
Serial wire debug interface clock input pin
Serial wire debug interface data input/output pin
Serial wire viewer output pin
J-TAG test clock input pin
J-TAG test data input pin
J-TAG debug data output pin
J-TAG test mode state input/output pin
J-TAG test reset Input pin
External interrupt request 00 input pin
External interrupt request 01 input pin
34
35
38
40
41
38
39
41
40
37
2
3
4
26
29
36
44
42
37
38
42
44
45
42
43
45
44
41
2
3
4
28
31
39
48
46
Document Number: 002-05625 Rev.*A
A/D converter analog input pin.
ANxx describes ADC ch.xx.
Base timer ch.0 TIOA pin
Base timer ch.0 TIOB pin
Base timer ch.1 TIOA pin
Base timer ch.1 TIOB pin
Base timer ch.2 TIOA pin
External interrupt request 02 input pin
External interrupt request 03 input pin
External interrupt request 06 input pin
External interrupt request 15 input pin
Non-Maskable Interrupt input pin
Page 16 of 87
MB9A310K Series
Module
Pin name
GPIO
P00
P01
P02
P03
P04
P0F
P10
P11
P12
P13
P14
P15
P21
P22
P23
P39
P3A
P3B
P3C
P3D
P3E
P3F
P46
P47
P49
P4A
P50
P51
P52
P60
P61
P80
P81
PE0
PE2
PE3
Document Number: 002-05625 Rev.*A
Function
General-purpose I/O port 0
General-purpose I/O port 1
General-purpose I/O port 2
General-purpose I/O port 3
General-purpose I/O port 4
General-purpose I/O port 5
General-purpose I/O port 6
General-purpose I/O port 8
General-purpose I/O port E
Pin No
LQFP-48
LQFP-52
QFN-48
37
38
39
40
41
42
25
26
27
28
29
30
36
35
34
5
6
7
8
9
10
11
15
16
18
19
2
3
4
44
43
46
47
20
22
23
41
42
43
44
45
46
27
28
29
30
31
32
39
38
37
6
7
8
9
10
11
12
16
17
19
20
2
3
4
48
47
50
51
22
24
25
Page 17 of 87
MB9A310K Series
Module
Pin name
Multi- function
Serial
0
SIN0_0
SIN0_1
SOT0_0
(SDA0_0)
SOT0_1
(SDA0_1)
SCK0_0
(SCL0_0)
Multi- function
Serial
1
SIN1_1
SOT1_1
(SDA1_1)
SCK1_1
(SCL1_1)
Multi- function
Serial
3
SIN3_1
SOT3_1
(SDA3_1)
SCK3_1
(SCL3_1)
Multi- function
Serial
5
SIN5_0
SOT5_0
Document Number: 002-05625 Rev.*A
Function
Multi-function serial interface ch.0 input pin
Multi-function serial interface ch.0 output pin.
This pin operates as SOT0 when it is used in a
UART/CSIO/LIN (operation modes
0 to 3) and as SDA0 when it is used in an I2C (operation
mode 4).
Multi-function serial interface ch.0 clock I/O pin.
This pin operates as SCK0 when it is used in a CSIO
(operation modes 2) and as SCL0 when it is used in an
I2C (operation mode 4).
Multi-function serial interface ch.1 input pin
Multi-function serial interface ch.1 output pin.
This pin operates as SOT1 when it is used in a
UART/CSIO/LIN (operation modes
0 to 3) and as SDA1 when it is used in an I2C (operation
mode 4).
Multi-function serial interface ch.1 clock I/O pin.
This pin operates as SCK1 when it is used in a CSIO
(operation modes 2) and as SCL1 when it is used in an
I2C (operation mode 4).
Multi-function serial interface ch.3 input pin
Multi-function serial interface ch.3 output pin.
This pin operates as SOT3 when it is used in a
UART/CSIO/LIN (operation modes
0 to 3) and as SDA3 when it is used in an I2C (operation
mode 4).
Multi-function serial interface ch.3 clock I/O pin.
This pin operates as SCK3 when it is used in a CSIO
(operation modes 2) and as SCL3 when it is used in an
I2C (operation mode 4).
Multi-function serial interface ch.5 input pin
Multi-function serial interface ch.5 output pin.
This pin operates as SOT5 when it is used in a
UART/LIN (operation modes 0, 1, 3).
Pin No.
LQFP-48
LQFP-52
QFN-48
36
29
39
31
35
38
30
32
34
37
26
28
27
29
28
30
2
2
3
3
4
4
44
48
43
47
Page 18 of 87
MB9A310K Series
Module
Pin name
Multi- function
Timer
0
DTTI0X_0
DTTI0X_2
FRCK0_2
IC00_0
IC00_2
IC01_2
IC02_0
IC02_2
IC03_2
RTO00_0
(PPG00_0)
RTO01_0
(PPG00_0)
RTO02_0
(PPG02_0)
RTO03_0
(PPG02_0)
RTO04_0
(PPG04_0)
RTO05_0
(PPG04_0)
Quadrature
Position/
Revolution
Counter
0
Real-time clock
Function
Input signal controlling wave form generator outputs
RTO00 to RTO05 of multi-function timer 0.
16-bit free-run timer ch.0 external clock input pin
16-bit input capture ch.0 input pin of multi-function timer
0.
ICxx describes channel number.
Wave form generator output pin of multi-function timer 0.
This pin operates as PPG00 when it is used in PPG0
output modes.
Wave form generator output pin of multi-function timer 0.
This pin operates as PPG00 when it is used in PPG0
output modes.
Wave form generator output pin of multi-function timer 0.
This pin operates as PPG02 when it is used in PPG0
output modes.
Wave form generator output pin of multi-function timer 0.
This pin operates as PPG02 when it is used in PPG0
output modes.
Wave form generator output pin of multi-function timer 0.
This pin operates as PPG04 when it is used in PPG0
output modes.
Wave form generator output pin of multi-function timer 0.
This pin operates as PPG04 when it is used in PPG0
output modes.
6
43
26
44
27
28
26
29
30
47
28
48
29
30
28
31
32
6
7
7
8
8
9
9
10
10
11
11
12
QPRC ch.0 AIN input pin
2
2
BIN0_2
QPRC ch.0 BIN input pin
3
3
ZIN0_2
QPRC ch.0 ZIN input pin
4
4
42
46
28
30
RTCCO_0
0.5 seconds pulse output pin of Real-time clock
RTCCO_2
6
7
SUBOUT_0
42
46
28
30
6
7
SUBOUT_1
Sub clock output pin
SUBOUT_2
USB
5
AIN0_2
RTCCO_1
Low Power
Consumption
Mode
Pin No
LQFP-48
LQFP-52
QFN-48
WKUP0
Deep stand-by mode return signal input pin 0
42
46
WKUP1
Deep stand-by mode return signal input pin 1
26
28
WKUP2
Deep stand-by mode return signal input pin 2
36
39
WKUP3
Deep stand-by mode return signal input pin 3
44
48
UDM0
USB ch.0 function/host D – pin
46
50
UDP0
USB ch.0 function/host D + pin
47
51
UHCONX
USB external pull-up control pin
43
47
Document Number: 002-05625 Rev.*A
Page 19 of 87
MB9A310K Series
Module
RESET
Pin name
VCC
VCC
USBVCC
VSS
VSS
VSS
X0
X0A
X1
X1A
CROUT_1
Built-in high-speed CR-osc clock output port
42
46
AVCC
A/D converter analog power pin
31
33
AVRH
A/D converter analog reference voltage input pin
32
34
AVSS
A/D converter GND pin
33
35
Power stabilization capacity pin
13
14
MD0
MD1
GND
CLOCK
Analog
POWER
Analog
GND
C pin
NC pin
Pin No
LQFP-48
LQFP-52
QFN-48
External Reset Input pin.
A reset is valid when INITX = "L".
Mode 0 pin.
During normal operation, MD0 = "L" must be input.
During serial programming to Flash memory, MD0 = "H"
must be input.
Mode 1 pin.
During serial programming to Flash memory, MD1 = "L"
must be input.
Power supply Pin
Power supply Pin
3.3V Power supply port for USB I/O
GND Pin
GND Pin
GND Pin
Main clock (oscillation) input pin
Sub clock (oscillation) input pin
Main clock (oscillation) I/O pin
Sub clock (oscillation) I/O pin
INITX
Mode
POWER
Function
C
17
18
21
23
20
22
1
14
45
12
24
48
22
15
23
16
1
15
49
13
26
52
24
16
25
17
NC
NC pin.
NC pin should be kept open.
-
5
NC
NC pin.
NC pin should be kept open.
-
21
NC
NC pin.
NC pin should be kept open.
-
36
NC
NC pin.
NC pin should be kept open.
-
40
Document Number: 002-05625 Rev.*A
Page 20 of 87
MB9A310K Series
5. I/O Circuit Type
Type
Circuit
Remarks
A
It is possible to select the main
oscillation / GPIO function
When the main oscillation is selected.
Pull-up
resistor
P-ch
• Oscillation feedback resistor
: Approximately 1MΩ
• With Standby mode control
P-ch
X1
Digital output
N-ch
R
Digital output
When the GPIO is selected.
•
•
•
•
•
CMOS level output.
CMOS level hysteresis input
With pull-up resistor control
With standby mode control
Pull-up resistor:
Approximately 50kΩ
• IOH = -4mA, IOL = 4mA
Pull-up resistor control
Digital input
Standby mode Control
Feedback
Clock input
resistor
Standby mode Control
Digital input
Pull-up
resistor
Standby mode Control
R
P-ch
P-ch
X0
Digital output
N-ch
Digital output
Pull-up resistor control
• CMOS level hysteresis input
• Pull-up resistor
: Approximately 50kΩ
B
Pull-up resistor
Digital input
Document Number: 002-05625 Rev.*A
Page 21 of 87
MB9A310K Series
Type
Circuit
Remarks
C
Digital input
• Open drain output
• CMOS level hysteresis input
Digital output
N-ch
D
It is possible to select the sub oscillation
/ GPIO function
When the sub oscillation is selected.
Pull-up
resistor
P-ch
P-ch
Digital output
X1A
• Oscillation feedback resistor
: Approximately 5MΩ
• With Standby mode control
When the GPIO is selected.
N-ch
Digital output
R
•
•
•
•
•
CMOS level output.
CMOS level hysteresis input
With pull-up resistor control
With standby mode control
Pull-up resistor
: Approximately 50kΩ
• IOH = -4mA, IOL = 4mA
Pull-up resistor control
Digital input
Standby mode Control
Clock input
Feedback
resistor
Standby mode Control
Digital input
Standby mode Control
Pull-up
resistor
R
P-ch
P-ch
Digital output
N-ch
Digital output
X0A
Pull-up resistor control
Document Number: 002-05625 Rev.*A
Page 22 of 87
MB9A310K Series
Type
Circuit
Remarks
•
•
•
•
•
E
P-ch
P-ch
N-ch
Digital output
Digital output
CMOS level output
CMOS level hysteresis input
With pull-up resistor control
With standby mode control
Pull-up resistor
: Approximately 50kΩ
• IOH = -4mA, IOL = 4mA
• When this pin is used as an
I2C pin, the digital output
P-ch transistor is always off
• +B input is available
R
Pull-up resistor control
Digital input
Standby mode Control
F
P-ch
P-ch
N-ch
R
Digital output
Digital output
•
•
•
•
•
•
•
CMOS level output
CMOS level hysteresis input
With input control
Analog input
With pull-up resistor control
With standby mode control
Pull-up resistor
: Approximately 50kΩ
• IOH = -4mA, IOL = 4mA
• When this pin is used as an
I2C pin, the digital output
P-ch transistor is always off
• +B input is available
Pull-up resistor control
Digital input
Standby mode Control
Analog input
Input control
Document Number: 002-05625 Rev.*A
Page 23 of 87
MB9A310K Series
Type
Circuit
Remarks
•
•
•
•
•
G
P-ch
P-ch
Digital output
N-ch
CMOS level output
CMOS level hysteresis input
With pull-up resistor control
With standby mode control
Pull-up resistor
: Approximately 50kΩ
• IOH = -12mA, IOL = 12mA
• +B input is available
Digital output
R
Pull-up resistor control
Digital input
Standby mode Control
H
GPIO Digital output
GPIO Digital input/output direction
GPIO Digital input
GPIO Digital input circuit control
UDP output
UDP/P81
USB Full-speed/Low-speed control
UDP input
Differential
UDM/P80
It is possible to select the
USB I/O / GPIO function.
When the USB I/O is selected.
• Full-speed, Low-speed control
When the GPIO is selected.
• CMOS level output
• CMOS level hysteresis input
• With standby mode control
IOH = -20.5mA,
IOL = 18.5mA
Differential input
USB/GPIO select
UDM input
UDM output
USB Digital input/output direction
GPIO Digital input
GPIO Digital input/output direction
GPIO Digital input
GPIO Digital input circuit control
Document Number: 002-05625 Rev.*A
Page 24 of 87
MB9A310K Series
Type
Circuit
Remarks
I
P-ch
P-ch
N-ch
Digital output
•
•
•
•
•
•
CMOS level output
CMOS level hysteresis input
5V tolerant
With pull-up resistor control
With standby mode control
Pull-up resistor
: Approximately 50kΩ
• IOH = -4mA, IOL = 4mA
• Available to control of PZR
registers.
Digital output
R
Pull-up resistor control
Digital input
Standby mode Control
• CMOS level hysteresis input
J
Mode input
Document Number: 002-05625 Rev.*A
Page 25 of 87
MB9A310K Series
6. Handling Precautions
Any semiconductor devices have inherently a certain rate of failure. The possibility of failure is greatly affected by the conditions in
which they are used (circuit conditions, environmental conditions, etc.). This page describes precautions that must be observed to
minimize the chance of failure and to obtain higher reliability from your Cypress semiconductor devices.
6.1
Precautions for Product Design
This section describes precautions when designing electronic equipment using semiconductor devices.
Absolute Maximum Ratings
Semiconductor devices can be permanently damaged by application of stress (voltage, current, temperature, etc.) in excess of
certain established limits, called absolute maximum ratings. Do not exceed these ratings.
Recommended Operating Conditions
Recommended operating conditions are normal operating ranges for the semiconductor device. All the device's electrical
characteristics are warranted when operated within these ranges.
Always use semiconductor devices within the recommended operating conditions. Operation outside these ranges may adversely
affect reliability and could result in device failure.
No warranty is made with respect to uses, operating conditions, or combinations not represented on the Datasheet. Users
considering application outside the listed conditions are advised to contact their sales representative beforehand.
Processing and Protection of Pins
These precautions must be followed when handling the pins which connect semiconductor devices to power supply and input/output
functions.
1. Preventing Over-Voltage and Over-Current Conditions
Exposure to voltage or current levels in excess of maximum ratings at any pin is likely to cause deterioration within the device,
and in extreme cases leads to permanent damage of the device. Try to prevent such overvoltage or over-current conditions at
the design stage.
2. Protection of Output Pins
Shorting of output pins to supply pins or other output pins, or connection to large capacitance can cause large current flows.
Such conditions if present for extended periods of time can damage the device.
Therefore, avoid this type of connection.
3. Handling of Unused Input Pins
Unconnected input pins with very high impedance levels can adversely affect stability of operation. Such pins should be
connected through an appropriate resistance to a power supply pin or ground pin.
Latch-up
Semiconductor devices are constructed by the formation of P-type and N-type areas on a substrate. When subjected to abnormally
high voltages, internal parasitic PNPN junctions (called thyristor structures) may be formed, causing large current levels in excess of
several hundred mA to flow continuously at the power supply pin. This condition is called latch-up.
CAUTION: The occurrence of latch-up not only causes loss of reliability in the semiconductor device, but can cause injury or
damage from high heat, smoke or flame. To prevent this from happening, do the following:
1. Be sure that voltages applied to pins do not exceed the absolute maximum ratings. This should include attention to abnormal
noise, surge levels, etc.
2. Be sure that abnormal current flows do not occur during the power-on sequence.
Observance of Safety Regulations and Standards
Most countries in the world have established standards and regulations regarding safety, protection from electromagnetic
interference, etc. Customers are requested to observe applicable regulations and standards in the design of products.
Fail-Safe Design
Any semiconductor devices have inherently a certain rate of failure. You must protect against injury, damage or loss from such
failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and
prevention of over-current levels and other abnormal operating conditions.
Document Number: 002-05625 Rev.*A
Page 26 of 87
MB9A310K Series
Precautions Related to Usage of Devices
Cypress semiconductor devices are intended for use in standard applications (computers, office automation and other office
equipment, industrial, communications, and measurement equipment, personal or household devices, etc.).
CAUTION: Customers considering the use of our products in special applications where failure or abnormal operation may directly
affect human lives or cause physical injury or property damage, or where extremely high levels of reliability are demanded (such
as aerospace systems, atomic energy controls, sea floor repeaters, vehicle operating controls, medical devices for life support,
etc.) are requested to consult with sales representatives before such use. The company will not be responsible for damages
arising from such use without prior approval.
6.2
Precautions for Package Mounting
Package mounting may be either lead insertion type or surface mount type. In either case, for heat resistance during soldering,
you should only mount under Cypress recommended conditions. For detailed information about mount conditions, contact your
sales representative.
Lead Insertion Type
Mounting of lead insertion type packages onto printed circuit boards may be done by two methods: direct soldering on the board,
or mounting by using a socket.
Direct mounting onto boards normally involves processes for inserting leads into through-holes on the board and using the flow
soldering (wave soldering) method of applying liquid solder. In this case, the soldering process usually causes leads to be
subjected to thermal stress in excess of the absolute ratings for storage temperature. Mounting processes should conform to
Cypress recommended mounting conditions.
If socket mounting is used, differences in surface treatment of the socket contacts and IC lead surfaces can lead to contact
deterioration after long periods. For this reason it is recommended that the surface treatment of socket contacts and IC leads be
verified before mounting.
Surface Mount Type
Surface mount packaging has longer and thinner leads than lead-insertion packaging, and therefore leads are more easily
deformed or bent. The use of packages with higher pin counts and narrower pin pitch results in increased susceptibility to open
connections caused by deformed pins, or shorting due to solder bridges.
You must use appropriate mounting techniques. Cypress recommends the solder reflow method, and has established a ranking of
mounting conditions for each product. Users are advised to mount packages in accordance with Cypress ranking of
recommended conditions.
Lead-Free Packaging
CAUTION: When ball grid array (BGA) packages with Sn-Ag-Cu balls are mounted using Sn-Pb eutectic soldering, junction
strength may be reduced under some conditions of use.
Storage of Semiconductor Devices
Because plastic chip packages are formed from plastic resins, exposure to natural environmental conditions will cause absorption
of moisture. During mounting, the application of heat to a package that has absorbed moisture can cause surfaces to peel,
reducing moisture resistance and causing packages to crack. To prevent, do the following:
1. Avoid exposure to rapid temperature changes, which cause moisture to condense inside the product. Store products in
locations where temperature changes are slight.
2. Use dry boxes for product storage. Products should be stored below 70% relative humidity, and at temperatures between 5°C
and 30°C.
When you open Dry Package that recommends humidity 40% to 70% relative humidity.
3. When necessary, Cypress packages semiconductor devices in highly moisture-resistant aluminum laminate bags, with a silica
gel desiccant. Devices should be sealed in their aluminum laminate bags for storage.
4. Avoid storing packages where they are exposed to corrosive gases or high levels of dust.
Document Number: 002-05625 Rev.*A
Page 27 of 87
MB9A310K Series
Baking
Packages that have absorbed moisture may be de-moisturized by baking (heat drying). Follow the Cypress recommended
conditions for baking.
Condition: 125°C/24 h
Static Electricity
Because semiconductor devices are particularly susceptible to damage by static electricity, you must take the following
precautions:
1. Maintain relative humidity in the working environment between 40% and 70%. Use of an apparatus for ion generation may be
needed to remove electricity.
2. Electrically ground all conveyors, solder vessels, soldering irons and peripheral equipment.
3. Eliminate static body electricity by the use of rings or bracelets connected to ground through high resistance (on the level of
1 MΩ).
Wearing of conductive clothing and shoes, use of conductive floor mats and other measures to minimize shock loads is
recommended.
4. Ground all fixtures and instruments, or protect with anti-static measures.
5. Avoid the use of styrofoam or other highly static-prone materials for storage of completed board assemblies.
6.3
Precautions for Use Environment
Reliability of semiconductor devices depends on ambient temperature and other conditions as described above.
For reliable performance, do the following:
1. Humidity
Prolonged use in high humidity can lead to leakage in devices as well as printed circuit boards. If high humidity levels are
anticipated, consider anti-humidity processing.
2. Discharge of Static Electricity
When high-voltage charges exist close to semiconductor devices, discharges can cause abnormal operation. In such cases,
use anti-static measures or processing to prevent discharges.
3. Corrosive Gases, Dust, or Oil
Exposure to corrosive gases or contact with dust or oil may lead to chemical reactions that will adversely affect the device. If
you use devices in such conditions, consider ways to prevent such exposure or to protect the devices.
4. Radiation, Including Cosmic Radiation
Most devices are not designed for environments involving exposure to radiation or cosmic radiation. Users should provide
shielding as appropriate.
5. Smoke, Flame
CAUTION: Plastic molded devices are flammable, and therefore should not be used near combustible substances. If devices
begin to smoke or burn, there is danger of the release of toxic gases.
Customers considering the use of Cypress products in other special environmental conditions should consult with sales
representatives.
Document Number: 002-05625 Rev.*A
Page 28 of 87
MB9A310K Series
7. Handling Devices
Power supply pins
In products with multiple VCC and VSS pins, respective pins at the same potential are interconnected within the device in order to
prevent malfunctions such as latch-up. However, all of these pins should be connected externally to the power supply or ground
lines in order to reduce electromagnetic emission levels, to prevent abnormal operation of strobe signals caused by the rise in the
ground level, and to conform to the total output current rating.
Moreover, connect the current supply source with each Power supply pins and GND pins of this device at low impedance. It is also
advisable that a ceramic capacitor of approximately 0.1 µF be connected as a bypass capacitor between each Power supply pins
and GND pins, between AVCC pin and AVSS pin near this device.
Stabilizing power supply voltage
A malfunction may occur when the power supply voltage fluctuates rapidly even though the fluctuation is within the recommended
operating conditions of the VCC power supply voltage. As a rule, with voltage stabilization, suppress the voltage fluctuation so that
the fluctuation in VCC ripple (peak-to-peak value) at the commercial frequency (50 Hz/60 Hz) does not exceed 10% of the VCC
value in the recommended operating conditions, and the transient fluctuation rate does not exceed 0.1 V/μs when there is a
momentary fluctuation on switching the power supply.
Crystal oscillator circuit
Noise near the X0/X1 and X0A/X1A pins may cause the device to malfunction. Design the printed circuit board so that X0/X1,
X0A/X1A pins, the crystal oscillator (or ceramic oscillator), and the bypass capacitor to ground are located as close to the device
as possible.
It is strongly recommended that the PC board artwork be designed such that the X0/X1 and X0A/X1A pins are surrounded by
ground plane as this is expected to produce stable operation.
Evaluate oscillation of your using crystal oscillator by your mount board.
Using an external clock
When using an external clock, the clock signal should be input to the X0, X0A pin only and the X1, X1A pin should be kept open.
Example of Using an External Clock
Device
X0(X0A)
Open
X1(X1A)
2
Handling when using Multi-function serial pin as I C pin
2
2
If it is using Multi-function serial pin as I C pins, P-ch transistor of digital output is always disable. However, I C pins need to keep
2
the electrical characteristic like other pins and not to connect to external I C bus system with power OFF.
Document Number: 002-05625 Rev.*A
Page 29 of 87
MB9A310K Series
C pin
This series contains the regulator. Be sure to connect a smoothing capacitor (C S) for the regulator between the C pin and the GND
pin. Please use a ceramic capacitor or a capacitor of equivalent frequency characteristics as a smoothing capacitor.
However, some laminated ceramic capacitors have the characteristics of capacitance variation due to thermal fluctuation (F
characteristics and Y5V characteristics). Please select the capacitor that meets the specifications in the operating conditions to
use by evaluating the temperature characteristics of a capacitor.
A smoothing capacitor of about 4.7μF would be recommended for this series.
C
Device
CS
VSS
GND
Mode pins (MD0)
Connect the MD pin (MD0) directly to VCC or VSS pins. Design the printed circuit board such that the pull-up/down resistance
stays low, as well as the distance between the mode pins and VCC pins or VSS pins is as short as possible and the connection
impedance is low, when the pins are pulled-up/down such as for switching the pin level and rewriting the Flash memory data. It is
because of preventing the device erroneously switching to test mode due to noise.
NC pins
NC pin should be kept open.
Notes on power-on
Turn power on/off in the following order or at the same time.
If not using the A/D converter, connect AVCC = VCC and AVSS = VSS.
Turning on :VCC → USBVCC
VCC → AVCC → AVRH
Turning off : USBVCC → VCC
AVRH → AVCC → VCC
Serial Communication
There is a possibility to receive wrong data due to the noise or other causes on the serial communication.
Therefore, design a printed circuit board so as to avoid noise.
Consider the case of receiving wrong data due to noise, perform error detection such as by applying a checksum of data at the
end. If an error is detected, retransmit the data.
Document Number: 002-05625 Rev.*A
Page 30 of 87
MB9A310K Series
Differences in features among the products with different memory sizes and between Flash products and
MASK products
The electric characteristics including power consumption, ESD, latch-up, noise characteristics, and oscillation characteristics
among the products with different memory sizes and between Flash products and MASK products are different because chip
layout and memory structures are different.
If you are switching to use a different product of the same series, please make sure to evaluate the electric characteristics.
Pull-Up function of 5V tolerant I/O
Please do not input the signal more than VCC voltage at the time of Pull-Up function use of 5V tolerant I/O.
Document Number: 002-05625 Rev.*A
Page 31 of 87
MB9A310K Series
8. Block Diagram
MB9AF311K, F312K
TRSTX,TCK,
TDI,TMS
TDO
SRAM0
8 Kbyte
SWJ-DP
ROM
Table
SRAM1
8 Kbyte
Multi-layer AHB (Max 42 MHz)
Cortex-M3 Core I
@40 MHz(Max)
D
NVIC
Sys
AHB-APB Bridge:
APB0(Max 42 MHz)
Dual-Timer
Watchdog Timer
(Software)
Clock Reset
Generator
INITX
Watchdog Timer
(Hardware)
MainFlash I/F
Security
MainFlash
64 Kbyte/
128 Kbyte
WorkFlash I/F
WorkFlash
32 Kbyte
USB2.0 PHY
(Host/
Func)
USBVCC
UDP0,UDM0
UHCONX
DMAC
4ch.
CSV
X0
X1
X0A
Main
Osc
Sub
Osc
PLL
AHB-AHB
Bridge
CLK
Source Clock
CR
4MHz
CR
100kHz
CROUT
AVCC,
AVSS,
AVRH
12-bit A/D Converter
USB Clock Ctrl
Unit 0
Power-On
Reset
AN[07:00]
Unit 1
LVD Ctrl
ADTG_2
AIN0
BIN0
ZIN0
QPRC
1ch.
A/D Activation Compare
3ch.
IC0x
FRCKx
16-bit Input Capture
4ch.
16-bit Free-Run Timer
3ch.
16-bit Output Compare
6ch.
DTTI0X
RTOx
Deep Standby Ctrl
AHB-APB Bridge : APB2 (Max 42 MHz)
TIOBx
LVD
Regulator
Base Timer
16-bit 8ch./
32-bit 4ch.
AHB-APB Bridge : APB1 (Max 42 MHz)
TIOAx
PLL
Waveform Generator
3ch.
16-bit PPG
3ch.
Multi-Function Timer
C
WKUP[3:0]
RTCCO,
SUBOUT
Real-Time Clock
IRQ-Monitor
CRC
Accelerator
Watch Counter
External Interrupt
Controller
6-pin + NMI
INTx
NMIX
MODE-Ctrl
GPIO
Multi-Function Serial I/F
4ch.
(with FIFO ch.0 - ch.1)
MD[1:0]
PIN-Function-Ctrl
P0x,
P1x,
.
.
.
PFx
SCKx
SINx
SOTx
9. Memory Size
See "Memory size" in "1. Product Lineup" to confirm the memory size.
Document Number: 002-05625 Rev.*A
Page 32 of 87
MB9A310K Series
10. Memory Map
Memory Map (1)
Peripherals Area
0x41FF_FFFF
Reserved
0x4006_1000
0xFFFF_FFFF
Reserved
0xE010_0000
0xE000_0000
Cortex-M3 Private
Peripherals
0x4006_0000
DMAC
0x4005_0000
Reserved
0x4004_0000
USB ch.0
Reserved
0x4003_C000
Reserved
0x7000_0000
0x6000_0000
External Device
Area
Reserved
0x4400_0000
0x4200_0000
0x4000_0000
32Mbyte
Bit band alias
Peripherals
Reserved
0x4003_B000
RTC
0x4003_A000
Watch Counter
0x4003_9000
CRC
0x4003_8000
MFS
0x4003_7000
0x4003_6000
Reserved
USB Clock Ctrl
0x4003_5000
LVD/DS mode
0x4003_4000
Reserved
0x4003_3000
GPIO
0x4003_2000
Reserved
0x4003_1000
Int-Req. Read
0x4003_0000
EXTI
0x4002_F000
Reserved
CR Trim
0x4002_E000
0x4002_8000
0x2400_0000
Reserved
A/DC
32Mbyte
Bit band alias
0x4002_7000
0x2200_0000
0x4002_6000
QPRC
0x200E_1000
Reserved
0x4002_5000
0x4002_4000
Base Timer
PPG
0x200E_0000
WorkFlash I/F
0x200C_0000
WorkFlash
0x2008_0000
Reserved
0x2000_0000
SRAM1
0x4002_1000
See the next page
"Memory Map (2)" for
0x1FFF_0000
SRAM0
0x4002_0000
MFT unit0
0x4001_6000
the memory size
details.
0x0010_2000
0x4001_5000
Reserved
Dual Timer
0x4001_3000
Reserved
0x4001_2000
SW WDT
0x0010_0000
Reserved
Security/CR Trim
MainFlash
0x0000_0000
Document Number: 002-05625 Rev.*A
Reserved
0x4001_1000
HW WDT
0x4001_0000
Clock/Reset
0x4000_1000
Reserved
0x4000_0000
MainFlash I/F
Page 33 of 87
MB9A310K Series
Memory Map (2)
MB9AF311K
MB9AF312K
0x200E_0000
0x200E_0000
Reserved
Reserved
0x200C_0000
0x200C_8000
SA0-3 (8KBx4)
0x200C_0000
Reserved
Reserved
0x2000_2000
0x2000_2000
SRAM1
8Kbyte
0x2000_0000
0x2000_0000
SRAM0
8Kbyte
0x1FFF_E000
0x1FFF_E000
SRAM1
8Kbyte
SRAM0
8Kbyte
Reserved
Reserved
0x0010_2000
0x0010_2000
0x0010_1000
WorkFlash
32Kbyte
SA0-3 (8KBx4)
WorkFlash
32Kbyte
0x200C_8000
CR trimming
0x0010_1000
CR trimming
Security
0x0010_0000
Security
0x0010_0000
Reserved
Reserved
0x0002_0000
SA4-7 (8KBx4)
0x0001_0000
SA8-9 (16KBx2)
0x0000_0000
MainFlash
64Kbyte
0x0000_0000
MainFlash
128Kbyte
SA8-9 (48KBx2)
SA4-7 (8KBx4)
See "MB9A310K/110K Series Flash programming Manual" for sector structure of Flash.
Document Number: 002-05625 Rev.*A
Page 34 of 87
MB9A310K Series
Peripheral Address Map
Start address
End address
Bus
Peripherals
0x4000_0000
0x4000_0FFF
0x4000_1000
0x4000_FFFF
0x4001_0000
0x4001_0FFF
Clock/Reset Control
0x4001_1000
0x4001_1FFF
Hardware Watchdog timer
0x4001_2000
0x4001_2FFF
0x4001_3000
0x4001_4FFF
0x4001_5000
0x4001_5FFF
0x4001_6000
0x4001_FFFF
Reserved
0x4002_0000
0x4002_0FFF
Multi-function timer unit0
0x4002_1000
0x4002_3FFF
Reserved
0x4002_4000
0x4002_4FFF
PPG
0x4002_5000
0x4002_5FFF
Base Timer
0x4002_6000
0x4002_6FFF
AHB
APB0
MainFlash I/F register
Reserved
Software Watchdog timer
Reserved
Dual-Timer
APB1
Quadrature Position/Revolution Counter
0x4002_7000
0x4002_7FFF
0x4002_8000
0x4002_DFFF
A/D Converter
Reserved
0x4002_E000
0x4002_EFFF
Internal CR trimming
0x4002_F000
0x4002_FFFF
Reserved
0x4003_0000
0x4003_0FFF
External Interrupt Controller
0x4003_1000
0x4003_1FFF
Interrupt Request Batch-Read Function
0x4003_2000
0x4003_2FFF
Reserved
0x4003_3000
0x4003_3FFF
GPIO
0x4003_4000
0x4003_4FFF
Reserved
0x4003_5000
0x4003_57FF
Low-Voltage Detector
0x4003_5800
0x4003_5FFF
Deep stand-by mode Controller
0x4003_6000
0x4003_6FFF
0x4003_7000
0x4003_7FFF
Reserved
0x4003_8000
0x4003_8FFF
Multi-function serial Interface
0x4003_9000
0x4003_9FFF
CRC
0x4003_A000
0x4003_AFFF
Watch Counter
0x4003_B000
0x4003_BFFF
Real-time clock
0x4003_C000
0x4003_FFFF
Reserved
0x4004_0000
0x4004_FFFF
USB ch.0
0x4005_0000
0x4005_FFFF
Reserved
0x4006_0000
0x4006_0FFF
0x4006_1000
0x41FF_FFFF
Reserved
0x200E_0000
0x200E_FFFF
WorkFlash I/F register
Document Number: 002-05625 Rev.*A
APB2
AHB
USB clock generator
DMAC register
Page 35 of 87
MB9A310K Series
11. Pin Status in Each CPU State
The terms used for pin status have the following meanings.
INITX = 0
This is the period when the INITX pin is the "L" level.
INITX = 1
This is the period when the INITX pin is the "H" level.
SPL = 0
This is the status that standby pin level setting bit (SPL) in standby mode control register (STB_CTL) is set to "0".
SPL = 1
This is the status that standby pin level setting bit (SPL) in standby mode control register (STB_CTL) is set to "1".
Input enabled
Indicates that the input function can be used.
Internal input fixed at "0"
This is the status that the input function cannot be used. Internal input is fixed at "L".
Hi-Z
Indicates that the output drive transistor is disabled and the pin is put in the Hi-Z state.
Setting disabled
Indicates that the setting is disabled.
Maintain previous state
Maintains the state that was immediately prior to entering the current mode.
If a built-in peripheral function is operating, the output follows the peripheral function.
If the pin is being used as a port, that output is maintained.
Analog input is enabled
Indicates that the analog input is enabled.
GPIO selected
In Deep stand-by mode, pins switch to the general-purpose I/O port.
Document Number: 002-05625 Rev.*A
Page 36 of 87
MB9A310K Series
Pin status type
List of Pin Status
Function
group
Power-on
reset or
low-voltage
detection
state
Power
supply
unstable
-
INITX
input
state
Device
internal
reset
state
Power supply stable
INITX = 0
-
INITX = 1
-
Run
mode or
sleep
mode
state
Power
supply
stable
INITX = 1
-
Timer mode,
RTC mode, or
sleep mode state
Deep stand-by RTC
mode or Deep stand-by
STOP mode state
Power supply stable
Power supply stable
INITX = 1
SPL = 0
SPL = 1
Hi-Z /
Maintain
Internal
previous
input fixed
state
at "0"
INITX = 1
SPL = 0
SPL = 1
Hi-Z /
Maintain
Internal
previous
input fixed
state
at "0"
Return
from Deep
stand-by
mode
state
Power
supply
stable
INITX = 1
-
GPIO
selected
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
Maintain
previous
state
Main crystal
oscillator
input pin
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
GPIO
selected
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Internal
input fixed
at "0"
Maintain
previous
state
Hi-Z /
Internal
input fixed
at "0"
Maintain
previous
state
Maintain
previous
state
/When
oscillation
stop[1],
Hi-Z/
Internal
input fixed
at "0"
Maintain
previous
state
/When
oscillation
stop[1],
Hi-Z/
Internal
input fixed
at "0"
Maintain
previous
state
/When
oscillation
stop[1],
Hi-Z/
Internal
input fixed
at "0"
Maintain
previous
state /When
oscillation
stop[1],
Hi-Z/
Internal
input fixed
at "0"
A
Main crystal
oscillator
output pin
Hi-Z/
Internal
input fixed at
"0"/
or Input
enable
Hi-Z /
Internal
input
fixed at
"0"
Hi-Z /
Internal
input
fixed at
"0"
Maintain
previous
state
Maintain
previous
state
/When
oscillation
stop[1],
Hi-Z/
Internal
input fixed
at "0"
C
INITX
input pin
Pull-up /
Input
enabled
Pull-up /
Input
enabled
Pull-up /
Input
enabled
Pull-up /
Input
enabled
Pull-up /
Input
enabled
Pull-up /
Input
enabled
Pull-up /
Input
enabled
Pull-up /
Input
enabled
Pull-up /
Input
enabled
D
Mode
input pin
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
B
Document Number: 002-05625 Rev.*A
Page 37 of 87
Pin status type
MB9A310K Series
Function
group
Power-on
reset or
low-voltage
detection
state
Power
supply
unstable
-
JTAG
selected
Hi-Z
INITX
input
state
Device
internal
reset
state
Power supply stable
INITX = 0
-
INITX = 1
-
Pull-up /
Input
enabled
Pull-up /
Input
enabled
Run
mode or
sleep
mode
state
Power
supply
stable
INITX = 1
-
Maintain
previous
state
E
Timer mode,
RTC mode, or
sleep mode state
Deep stand-by RTC
mode or Deep stand-by
STOP mode state
Power supply stable
Power supply stable
INITX = 1
SPL = 0
SPL = 1
INITX = 1
SPL = 0
SPL = 1
Maintain
previous
state
Power
supply
stable
INITX = 1
-
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Internal
input fixed
at "0"
Maintain
previous
state
Hi-Z /
Internal
input fixed
at "0"
Maintain
previous
state
GPIO
selected
Setting
disabled
Setting
disabled
Setting
disabled
WKUP
enabled
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
WKUP
input
enabled
Hi-Z /
WKUP
input
enabled
GPIO
selected
Hi-Z
Hi-Z /
Internal
input
fixed at
"0" /
Analog
input
enabled
Hi-Z /
Internal
input
fixed at
"0" /
Analog
input
enabled
Hi-Z /
Internal
input
fixed at
"0" /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at "0" /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at "0" /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at "0" /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at "0" /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at "0" /
Analog
input
enabled
Analog
input
selected
F
External
interrupt
enabled
selected
Resource
other than
above
selected
Maintain
previous
state
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
Maintain
previous
state
GPIO
selected
WKUP
enabled
G
Return
from Deep
stand-by
mode
state
External
interrupt
enabled
selected
Resource
other than
above
selected
GPIO
selected
Setting
disabled
Setting
disabled
Setting
disabled
Setting
disabled
Setting
disabled
Setting
disabled
Hi-Z
Hi-Z /
Input
enabled
Document Number: 002-05625 Rev.*A
Hi-Z /
Input
enabled
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Internal
input fixed
at "0"
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Internal
input fixed
at "0"
GPIO
selected
Hi-Z /
Internal
input fixed
at "0"
Maintain
previous
state
WKUP
input
enabled
GPIO
selected
Maintain
previous
state
GPIO
selected
Maintain
previous
state
Hi-Z /
WKUP
input
enabled
GPIO
selected
Hi-Z /
Internal
input fixed
at "0"
GPIO
selected
Maintain
previous
state
Page 38 of 87
Pin status type
MB9A310K Series
H
Function
group
Power-on
reset or
low-voltage
detection
state
Power
supply
unstable
-
External
interrupt
enabled
selected
Resource
other than
above
selected
Setting
disabled
NMIX
selected
J
Resource
other than
above
selected
INITX = 1
-
Setting
disabled
Setting
disabled
Hi-Z
Hi-Z /
Input
enabled
Setting
disabled
Setting
disabled
Setting
disabled
Run
mode or
sleep
mode
state
Power
supply
stable
INITX = 1
-
Timer mode,
RTC mode, or
sleep mode state
Deep stand-by RTC
mode or Deep stand-by
STOP mode state
Power supply stable
Power supply stable
INITX = 1
SPL = 0
SPL = 1
INITX = 1
SPL = 0
SPL = 1
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Internal
input fixed
at "0"
Hi-Z /
Internal
input fixed
at "0"
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Internal
input fixed
at "0"
Hi-Z /
Input
enabled
Hi-Z
Hi-Z /
Internal
input
fixed at
"0" /
Analog
input
enabled
Hi-Z /
Internal
input
fixed at
"0" /
Analog
input
enabled
Hi-Z /
Internal
input
fixed at
"0" /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at "0" /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at "0" /
Analog
input
enabled
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Internal
input fixed
at "0"
Hi-Z
GPIO
selected
Document Number: 002-05625 Rev.*A
GPIO
selected
Maintain
previous
state
GPIO
selected
Maintain
previous
state
Hi-Z /
Internal
input fixed
at "0"
Hi-Z /
Internal
input fixed
at "0"
Maintain
previous
state
Hi-Z /
Input
enabled
K
Resource
other than
above
selected
INITX = 0
-
Hi-Z /
Input
enabled
Hi-Z
GPIO
selected
Analog
input
selected
Power supply stable
Hi-Z /
Input
enabled
resource
selected
GPIO
selected
Device
internal
reset
state
Hi-Z /
Input
enabled
GPIO
selected
I
INITX
input
state
WKUP
input
enabled
Return
from Deep
stand-by
mode
state
Power
supply
stable
INITX = 1
-
GPIO
selected
Maintain
previous
state
GPIO
selected
Maintain
previous
state
GPIO
selected
Hi-Z /
WKUP
input
enabled
Maintain
previous
state
Hi-Z /
Internal
input fixed
at "0" /
Analog
input
enabled
GPIO
selected
Maintain
previous
state
Hi-Z /
Internal
input fixed
at "0" /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at "0"
Hi-Z /
Internal
input fixed
at "0" /
Analog
input
enabled
GPIO
selected
Maintain
previous
state
Page 39 of 87
Pin status type
MB9A310K Series
Function
group
Power
supply
unstable
-
Analog
input
selected
L
Power-on
reset or
low-voltage
detection
state
External
interrupt
enabled
selected
Resource
other than
above
selected
Hi-Z
INITX
input
state
Device
internal
reset
state
Power supply stable
INITX = 0
Hi-Z /
Internal
input
fixed at
"0" /
Analog
input
enabled
INITX = 1
Hi-Z /
Internal
input
fixed at
"0" /
Analog
input
enabled
Run
mode or
sleep
mode
state
Power
supply
stable
INITX = 1
Hi-Z /
Internal
input
fixed at
"0" /
Analog
input
enabled
Timer mode,
RTC mode, or
sleep mode state
Deep stand-by RTC
mode or Deep stand-by
STOP mode state
Power supply stable
Power supply stable
INITX = 1
SPL = 0
SPL = 1
INITX = 1
SPL = 0
SPL = 1
Hi-Z /
Internal
input fixed
at "0" /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at "0" /
Analog
input
enabled
Maintain
previous
state
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
Maintain
previous
state
GPIO
selected
Hi-Z /
Internal
input fixed
at "0"
Hi-Z /
Internal
input fixed
at "0" /
Analog
input
enabled
GPIO
selected
Hi-Z /
Internal
input fixed
at "0" /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at "0"
Maintain
previous
state
Return
from Deep
stand-by
mode
state
Power
supply
stable
INITX = 1
Hi-Z /
Internal
input fixed
at "0" /
Analog
input
enabled
GPIO
selected
Maintain
previous
state
GPIO
selected
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Internal
input fixed
at "0"
Maintain
previous
state
Hi-Z /
Internal
input fixed
at "0"
Maintain
previous
state
Sub crystal
oscillator
input pin
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
GPIO
selected
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
Maintain
previous
state
Sub crystal
oscillator
output pin
Hi-Z/
Internal
input fixed at
"0"/
or Input
enable
Maintain
previous
state
Maintain
previous
state
/When
oscillation
stop[2],Hi-Z
/ Internal
input fixed
at "0"
M
N
Hi-Z /
Internal
input
fixed at
"0"
Document Number: 002-05625 Rev.*A
Hi-Z /
Internal
input
fixed at
"0"
Hi-Z /
Internal
input fixed
at "0"
Maintain
previous
state
/When
oscillation
stop[2],Hi-Z
/ Internal
input fixed
at "0"
Maintain
previous
state
Maintain
previous
state
/When
oscillation
stop[2],Hi-Z
/ Internal
input fixed
at "0"
Hi-Z /
Internal
input fixed
at "0"
Maintain
previous
state
/When
oscillation
stop[2],Hi-Z
/ Internal
input fixed
at "0"
Maintain
previous
state
Maintain
previous
state /When
oscillation
stop[2],Hi-Z/
Internal
input fixed
at "0"
Page 40 of 87
Pin status type
MB9A310K Series
Function
group
Power-on
reset or
low-voltage
detection
state
Power
supply
unstable
-
INITX
input
state
Device
internal
reset
state
Run
mode or
sleep
mode
state
INITX = 0
-
INITX = 1
-
Power
supply
stable
INITX = 1
-
Power supply stable
GPIO
selected
Hi-Z
Hi-Z /
Input
enabled
Hi-Z /
Input
enabled
Maintain
previous
state
USB I/O pin
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
Mode
input pin
Input
enabled
Input
enabled
Input
enabled
GPIO
selected
Setting
disabled
Setting
disabled
Setting
disabled
O
P
Input
enabled
Maintain
previous
state
Timer mode,
RTC mode, or
sleep mode state
Deep stand-by RTC
mode or Deep stand-by
STOP mode state
Power supply stable
Power supply stable
INITX = 1
SPL = 0
SPL = 1
Hi-Z /
Maintain
Internal
previous
input fixed
state
at "0"
Hi-Z at
Hi-Z at
transmistransmission / Input sion/ Input
enabled/
enabled/
Internal
Internal
input fixed
input fixed
at "0" at
at "0" at
reception
reception
Input
Input
enabled
enabled
Maintain
Hi-Z /
previous
Input
state
enabled
INITX = 1
SPL = 0
SPL = 1
Hi-Z /
Maintain
Internal
previous
input fixed
state
at "0"
Return
from Deep
stand-by
mode
state
Power
supply
stable
INITX = 1
Maintain
previous
state
Hi-Z /
Input
enabled
Hi-Z /
Input
enabled
Hi-Z /
Input
enabled
Input
enabled
Maintain
previous
state
Input
enabled
Hi-Z /
Input
enabled
Input
enabled
Maintain
previous
state
[1]: Oscillation is stopped at Sub timer mode, Low-speed CR timer mode, RTC mode, STOP mode, Deep stand-by RTC mode,
and Deep stand-by STOP mode.
[2]: Oscillation is stopped at STOP mode and Deep stand-by STOP mode.
Document Number: 002-05625 Rev.*A
Page 41 of 87
MB9A310K Series
12. Electrical Characteristics
12.1 Absolute Maximum Ratings
Parameter
Power supply voltage
[1], [2]
Power supply voltage (for USB)
[1], [3]
[1], [4]
Analog power supply voltage
Analog reference voltage [1], [2]
Symbol
Rating
Max
Vcc
Vss - 0.5
Vss + 6.5
V
USBVcc
Vss - 0.5
Vss + 6.5
V
AVcc
AVRH
Vss - 0.5
Vss - 0.5
Vss + 6.5
Vss + 6.5
Vcc + 0.5
(≤6.5V)
USBVcc0 + 0.5
(≤6.5V)
V
V
Vss + 6.5
Vss - 0.5
Input voltage
VI
Vss - 0.5
Vss - 0.5
Analog pin input voltage
VIA
Vss - 0.5
Output voltage
VO
Vss - 0.5
ICLAMP
Σ[ICLAMP]
-2
IOL
-
IOLAV
-
∑IOL
∑IOLAV
-
IOH
-
IOHAV
-
∑IOH
∑IOHAV
PD
TSTG
- 55
Clamp maximum current
Clamp total maximum current
"L" level maximum output current[5]
"L" level average output current[6]
"L" level total maximum output current
"L" level total average output current[7]
"H" level maximum output current[5]
"H" level average output current[6]
"H" level total maximum output current
"H" level total average output current[7]
Power consumption
Storage temperature
Unit
Min
Remarks
V
Except for USB pin
V
USB pin
V
5V tolerant
AVcc + 0.5
(≤6.5V)
Vcc + 0.5
(≤6.5V)
+2
+20
10
20
39
4
12
18.5
100
50
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
- 10
mA
4mA type
- 20
- 39
-4
- 12
- 20.5
- 100
- 50
300
+ 150
mA
mA
mA
mA
mA
mA
mA
mW
°C
12mA type
P80, P81
4mA type
12mA type
P80, P81
V
V
[8]
[8]
4mA type
12mA type
P80, P81
4mA type
12mA type
P80, P81
[1]: These parameters are based on the condition that VSS = AVSS = 0.0V.
[2]: Vcc must not drop below VSS - 0.5V.
[3]: USBVcc must not drop below VSS - 0.5V.
[4]: Ensure that the voltage does not to exceed Vcc + 0.5 V, for example, when the power is turned on.
[5]: The maximum output current is the peak value for a single pin.
[6]: The average output is the average current for a single pin over a period of 100 ms.
[7]: The total average output current is the average current for all pins over a period of 100 ms.
Document Number: 002-05625 Rev.*A
Page 42 of 87
MB9A310K Series
[8]
•
•
•
•
•
See "List of Pin Functions" and "I/O Circuit Type" about +B input available pin.
Use within recommended operating conditions.
Use at DC voltage (current) the +B input.
The +B signal should always be applied a limiting resistance placed between the +B signal and the device.
The value of the limiting resistance should be set so that when the +B signal is applied the input current to the device pin does
not exceed rated values, either instantaneously or for prolonged periods.
• Note that when the device drive current is low, such as in the low-power consumpsion modes, the +B input potential may pass
through the protective diode and increase the potential at the VCC and AVCC pin, and this may affect other devices.
• Note that if a +B signal is input when the device power supply is off (not fixed at 0V), the power supply is provided from the
pins, so that incomplete operation may result.
• The following is a recommended circuit example (I/O equivalent circuit).
Protection Diode
VCC
VCC
Limiting
resistor
P-ch
+B input (0V to 16V)
Digital output
N-ch
R
Digital input
AVCC
Analog input
WARNING:
Semiconductor devices can be permanently damaged by application of stress (voltage, current, temperature, etc.) in excess of
absolute maximum ratings. Do not exceed these ratings.
Document Number: 002-05625 Rev.*A
Page 43 of 87
MB9A310K Series
12.2 Recommended Operating Conditions
(Vss = AVss = 0.0V)
Parameter
Power supply voltage
Symbol
Vcc
Conditions
-
Value
Min
[4]
2.7
3.0
Power supply voltage for USB
USBVcc
-
Max
5.5
3.6
(≤Vcc)
Unit
V
[1]
V
AVcc
AVRH
-
2.7
2.7
5.5
(≤Vcc)
5.5
AVcc
Smoothing capacitor
CS
-
1
10
μF
Operating temperature
Ta
-
- 40
+ 105
°C
2.7
Analog power supply voltage
Analog reference voltage
Remarks
[2]
V
V
AVcc = Vcc
For built-in
regulator[3]
[1]: When P81/UDP0 and P80/UDM0 pin are used as USB (UDP0, UDM0).
[2]: When P81/UDP0 and P80/UDM0 pin are used as GPIO (P81, P80).
[3]: See "C Pin" in "Handling Devices" for the connection of the smoothing capacitor.
[4]: In between less than the minimum power supply voltage and low voltage reset/interrupt detection voltage
or more, instruction execution and low voltage detection function by built-in High-speed CR (including Main PLL is used)
or built-in Low-speed CR is possible to operate only.
WARNING:
The recommended operating conditions are required in order to ensure the normal operation of the semiconductor device. All of the
device's electrical characteristics are warranted when the device is operated within these ranges.
Always use semiconductor devices within their recommended operating condition ranges. Operation outside these ranges may
adversely affect reliability and could result in device failure. No warranty is made with respect to uses, operating conditions, or
combinations not represented on the Datasheet. Users considering application outside the listed conditions are advised to contact
their representatives beforehand.
Document Number: 002-05625 Rev.*A
Page 44 of 87
MB9A310K Series
12.3 DC Characteristics
12.3.1 Current Rating
(Vcc = AVcc = 2.7V to 5.5V, USBVcc = 3.0V to 3.6V, Vss = AVss = 0V, Ta = - 40°C to + 105°C)
Parameter
Symbol
Pin
Name
Conditions
PLL
RUN mode
RUN
mode
current
Icc
High-speed
CR
RUN mode
VCC
Sub
RUN mode
Low-speed
CR
RUN mode
SLEEP
mode
current
Iccs
PLL
SLEEP mode
High-speed
CR
SLEEP mode
Sub
SLEEP mode
Low-speed
CR
SLEEP mode
CPU : 40 MHz,
Peripheral : 40 MHz,
MainFlash 0 Wait
FRWTR.RWT = 00
FSYNDN.SD = 000
CPU : 40 MHz,
Peripheral : 40 MHz,
MainFlash 3 Wait
FRWTR.RWT = 00
FSYNDN.SD = 011
Typ
Value
[4]
Max
[3]
Unit
Remarks
32
41
mA
[1], [5]
21
28
mA
[1], [5]
3.9
7.7
mA
[1]
0.15
3.2
mA
[1], [6]
0.2
3.3
mA
[1]
Peripheral : 40 MHz
10
15
mA
[1], [5]
Peripheral : 4 MHz[2]
1.2
4.4
mA
[1]
Peripheral : 32 kHz
0.1
3.1
mA
[1], [6]
Peripheral : 100 kHz
0.1
3.1
mA
[1]
CPU/ Peripheral : 4 MHz*2
MainFlash 0 Wait
FRWTR.RWT = 00
FSYNDN.SD = 000
CPU/ Peripheral : 32 kHz
MainFlash 0 Wait
FRWTR.RWT = 00
FSYNDN.SD = 000
CPU/ Peripheral : 100 kHz
MainFlash 0 Wait
FRWTR.RWT = 00
FSYNDN.SD = 000
[1]: When all ports are fixed.
[2]: When setting it to 4 MHz by trimming.
[3]: Ta = +25°C, VCC = 5.5V
[4]:Ta = +105°C, VCC = 5.5V
[5]: When using the crystal oscillator of 4 MHz (Including the current consumption of the oscillation circuit)
[6]: When using the crystal oscillator of 32 kHz (Including the current consumption of the oscillation circuit)
Document Number: 002-05625 Rev.*A
Page 45 of 87
MB9A310K Series
(Vcc = AVcc = 2.7V to 5.5V, USBVcc = 3.0V to 3.6V, Vss = AVss = 0V, Ta = - 40°C to + 105°C)
Parameter
Symbol
Pin
Name
Conditions
Main
TIMER
mode
TIMER
mode
current
ICCT
Sub
TIMER
mode
RTC
mode
current
ICCR
STOP
mode
current
ICCH
RTC mode
STOP mode
VCC
ICCRD
Deep
stand-by
RTC mode
Deep
stand-by
mode
current
ICCHD
Deep
stand-by
STOP mode
Ta = + 25°C,
When LVD is off
Ta = + 105°C,
When LVD is off
[3]
Ta = + 25°C,
When LVD is off
[4]
Ta = + 105°C,
When LVD is off
[4]
Ta = + 25°C,
When LVD is off
Ta = + 105°C,
When LVD is off
Ta = + 25°C,
When LVD is off
Ta = + 105°C,
When LVD is off
Ta = + 25°C,
When LVD is off
RAM hold off
Ta = + 25°C,
When LVD is off
RAM hold on
Ta = + 105°C,
When LVD is off
RAM hold off
Ta = + 105°C,
When LVD is off
RAM hold on
Ta = + 25°C,
When LVD is off
RAM hold off
Ta = + 25°C,
When LVD is off
RAM hold on
Ta = + 105°C,
When LVD is off
RAM hold off
Ta = + 105°C,
When LVD is off
RAM hold on
Typ*
Value
2
Max*
2
Unit
Remarks
5.2
6
mA
[1], [3]
-
9
mA
[1], [3]
60
230
μA
[1], [4]
-
3.1
mA
[1], [4]
50
210
μA
[1], [4]
-
3.1
mA
[1], [4]
35
200
μA
[1]
-
3
mA
[1]
30
160
μA
[1], [4]
33
160
mA
[1], [4]
-
600
μA
[1]
-
610
mA
[1]
20
150
μA
[1], [4]
23
150
mA
[1], [4]
-
600
μA
[1]
-
610
mA
[1]
[1]: When all ports are fixed.
[2]: VCC = 5.5V
[3]: When using the crystal oscillator of 4 MHz (Including the current consumption of the oscillation circuit)
[4]: When using the crystal oscillator of 32 kHz (Including the current consumption of the oscillation circuit)
Document Number: 002-05625 Rev.*A
Page 46 of 87
MB9A310K Series
Low-Voltage Detection Current
(VCC = 2.7V to 5.5V, VSS = 0V, Ta = - 40°C to + 105°C)
Parameter
Low-voltage detection
circuit (LVD) power
supply current
Symbol
ICCLVD
Pin
name
VCC
Value
Conditions
At operation
for interrupt
Vcc = 5.5V
Typ
4
Max
Unit
μA
7
Remarks
At not detect
Flash Memory Current
(VCC = 2.7V to 5.5V, VSS = 0V, Ta = - 40°C to + 105°C)
Parameter
Flash memory
write/erase
current
Symbol
ICCFLASH
Pin
name
VCC
Value
Conditions
MainFlash
At Write/Erase
WorkFlash
At Write/Erase
Typ
Max
Unit
11.4
13.1
mA
11.4
13.1
mA
Remarks
A/D Converter Current
(VCC = AVCC = 2.7V to 5.5V, VSS = AVSS = AVRL = 0V, Ta = - 40°C to + 105°C)
Parameter
Power supply current
Reference power
supply current
Symbol
ICCAD
ICCAVRH
Document Number: 002-05625 Rev.*A
Pin
name
Value
Conditions
Typ
Max
Unit
At 1unit operation
0.57
0.72
mA
At stop
0.06
20
μA
At 1unit operation
AVRH = 5.5V
1.1
1.96
mA
At stop
0.06
4
μA
Remarks
AVCC
AVRH
Page 47 of 87
MB9A310K Series
12.3.2 Pin Characteristics
(Vcc = AVcc = 2.7V to 5.5V, Vss = AVss = 0V, Ta = - 40°C to + 105°C)
Parameter
Symbol
"H" level input
voltage
(hysteresis
input)
VIHS
"L" level
input
voltage
(hysteresis
input)
VILS
Pin name
CMOS
hysteresis
input pin, MD0,
MD1
5V tolerant
input pin
CMOS
hysteresis
input pin, MD0,
MD1
5V tolerant
input pin
4mA
type
"H" level
output voltage
VOH
12mA
type
P80/P81
4mA type
"L" level
output voltage
VOL
12mA type
P80/P81
Input leak current
IIL
-
Pull-up resistance
Value
RPU
Pull-up pin
Input capacitance
CIN
Other than
VCC,
USBVCC,
VSS,
AVCC,
AVSS, AVRH
Document Number: 002-05625 Rev.*A
Conditions
Min
Value
Typ
Max
Unit
-
Vcc × 0.8
-
Vcc + 0.3
V
-
Vcc × 0.8
-
Vss + 5.5
V
-
Vss - 0.3
-
Vcc × 0.2
V
-
Vss - 0.3
-
Vcc × 0.2
V
Vcc - 0.5
-
Vcc
V
Vcc - 0.5
-
Vcc
V
USBVcc - 0.4
-
USBVcc
V
Vss
-
0.4
V
Vss
-
0.4
V
Vss
-
0.4
V
-5
-
+5
μA
Vcc ≥ 4.5 V
25
50
100
Vcc < 4.5 V
30
80
200
-
-
5
15
Vcc ≥ 4.5 V
IOH = - 4mA
Remarks
Vcc < 4.5 V
IOH = - 2mA
Vcc ≥ 4.5 V
IOH = - 12mA
Vcc < 4.5 V
IOH = - 8mA
USBVcc ≥ 4.5 V
IOH = - 20.5 mA
USBVcc < 4.5 V
IOH = - 13.0 mA
Vcc ≥ 4.5 V
IOL = 4mA
Vcc < 4.5 V
IOL = 2mA
Vcc ≥ 4.5 V
IOL = 12mA
Vcc < 4.5 V
IOL = 8mA
USBVcc ≥ 4.5 V
IOL = 18.5mA
USBVcc< 4.5 V
IOL = 10.5mA
-
kΩ
Pf
Page 48 of 87
MB9A310K Series
12.4 AC Characteristics
12.4.1 Main Clock Input Characteristics
(Vcc = 2.7V to 5.5V, Vss = 0V, Ta = - 40°C to + 105°C)
Parameter
Input frequency
Pin
name
Symbol
FCH
Input clock cycle
tCYLH
Input clock pulse width
-
Input clock rise time and
fall time
tCF,
tCR
Internal operating
clock frequency[1]
Internal operating
clock cycle time[1]
X0
X1
Value
Conditions
Min
Max
Unit
Vcc ≥ 4.5V
Vcc < 4.5V
Vcc ≥ 4.5V
Vcc < 4.5V
Vcc ≥ 4.5V
Vcc < 4.5V
PWH/tCYLH
PWL/tCYLH
4
4
4
4
20.83
50
48
20
48
20
250
250
45
55
%
-
-
5
ns
Remarks
MHz
When crystal oscillator is
connected
MHz
When using external
Clock
ns
When using external
Clock
When using external
Clock
When using external
Clock
FCM
-
-
-
42
MHz
Master clock
FCC
-
-
-
42
MHz
Base clock (HCLK/FCLK)
FCP0
FCP1
-
-
-
42
42
MHz
MHz
APB0 bus clock[2]
APB1 bus clock[2]
FCP2
-
-
-
42
MHz
APB2 bus clock[2]
tCYCC
-
-
23.8
-
ns
Base clock (HCLK/FCLK)
tCYCP0
tCYCP1
-
-
23.8
23.8
-
ns
ns
APB0 bus clock[2]
APB1 bus clock[2]
tCYCP2
-
-
23.8
-
ns
APB2 bus clock[2]
[1]: For more information about each internal operating clock, see "Chapter 2-1: Clock" in "FM3 Family Peripheral Manual".
[2]: For about each APB bus which each peripheral is connected to, see "Block Diagram" in this datasheet.
X0
Document Number: 002-05625 Rev.*A
Page 49 of 87
MB9A310K Series
12.4.2 Sub Clock Input Characteristics
Parameter
Symbol
Input frequency
1/ tCYLL
Input clock cycle
tCYLL
Input clock pulse width
Pin
name
X0A
X1A
-
Conditions
(Vcc = 2.7V to 5.5V, Vss = 0V, Ta = - 40°C to + 105°C)
Value
Unit
Remarks
Typ
Max
Min
-
-
32.768
-
kHz
-
32
-
100
kHz
When crystal oscillator is
connected
When using external clock
-
10
-
31.25
μs
When using external clock
PWH/tCYLL
PWL/tCYLL
45
-
55
%
When using external clock
X0A
12.4.3 Internal CR Oscillation Characteristics
High-speed Internal CR
(Vcc = 2.7V to 5.5V, Vss = 0V, Ta = - 40°C to + 105°C)
Parameter
Symbol
Ta = + 25°C
Clock frequency
Frequency stability time
FCRH
tCRWT
Value
Conditions
Ta =
0°C to + 70°C
Ta =
- 40°C to + 85°C
Ta =
- 40°C to + 85°C
-
Min
Typ
Max
3.96
4
4.04
3.84
4
4.16
3.8
4
4.2
3
4
5
-
-
90
Unit
Remarks
When trimming[1]
MHz
When not trimming
μs
[2]
[1]: In the case of using the values in CR trimming area of Flash memory at shipment for frequency trimming.
[2]: Frequency stable time is time to stable of the frequency of the High-speed CR.
clock after the trim value is set. After setting the trim value, the period when the frequency stability
time passes can use the High-speed CR clock as a source clock.
Low-speed Internal CR
Parameter
Clock frequency
Symbol
FCRL
Document Number: 002-05625 Rev.*A
Conditions
-
Min
50
(Vcc = 2.7V to 5.5V, Vss = 0V, Ta = - 40°C to + 105°C)
Value
Unit
Remarks
Typ
Max
100
150
kHz
Page 50 of 87
MB9A310K Series
12.4.4 Operating Conditions of Main and USB PLL (In the case of using main clock for input of PLL
(Vcc = 2.7V to 5.5V, Vss = 0V, Ta = - 40°C to + 105°C)
Value
Parameter
Symbol
Unit
Remarks
Min Typ Max
PLL oscillation stabilization wait time[1]
(LOCK UP time)
tLOCK
100
-
-
μs
PLL input clock frequency
PLL multiple rate
PLL macro oscillation clock frequency
Main PLL clock frequency[2]
USB clock frequency[3]
FPLLI
FPLLO
FCLKPLL
FCLKSPLL
4
13
200
-
-
16
75
300
40
48
MHz
multiple
MHz
MHz
MHz
After the M frequency division
[1]: Time from when the PLL starts operating until the oscillation stabilizes.
[2]: For more information about Main PLL clock (CLKPLL), see "Chapter 2-1: Clock" in "FM3 Family Peripheral Manual".
[3]: For more information about USB clock, see "Chapter 2-2: USB Clock Generation" in "FM3 Family Peripheral Manual
Communication Macro Part".
12.4.5 Operating Conditions of Main PLL (In the case of using high-speed internal CR)
(Vcc = 2.7V to 5.5V, Vss = 0V, Ta = - 40°C to + 105°C)
Value
Parameter
Symbol
Unit
Remarks
Min Typ Max
PLL oscillation stabilization wait time[1]
(LOCK UP time)
tLOCK
100
-
-
μs
PLL input clock frequency
PLL multiple rate
PLL macro oscillation clock frequency
Main PLL clock frequency[2]
FPLLI
FPLLO
FCLKPLL
3.8
50
190
-
4
-
4.2
71
300
42
MHz
multiple
MHz
MHz
[1]: Time from when the PLL starts operating until the oscillation stabilizes.
[2]: For more information about Main PLL clock (CLKPLL), see "Chapter 2-1: Clock" in "FM3 Family Peripheral Manual".
When setting PLL multiple rate, please take the accuracy of the built-in high-speed CR clock into account and prevent the
master clock from exceeding the maximum frequency.
Document Number: 002-05625 Rev.*A
Page 51 of 87
MB9A310K Series
12.4.6 Reset Input Characteristics
(Vcc = 2.7V to 5.5V, Vss = 0V, Ta = - 40°C to + 105°C)
Value
Parameter
Symbol
Pin name
Conditions
Unit
Min
Reset input time
tINITX
INITX
-
Remarks
Max
500
-
ns
12.4.7 Power-on Reset Timing
Parameter
Pin
name
Symbol
Power supply rising time
Tr
Power supply shut down time
Toff
Time until releasing
Power-on reset
Tprt
(Vcc = 2.7V to 5.5V, Vss = 0V, Ta = - 40°C to + 105°C)
Value
Unit
Remarks
Min
Max
VCC
0
-
ms
1
-
ms
0.66
0.89
ms
VCC_minimum
VCC
VDH_minimum
0.2V
0.2V
0.2V
Tr
Tprt
Internal RST
RST Active
CPU Operation
Toff
Release
start
Glossary
VCC_minimum
: Minimum VCC of recommended operating conditions
VDH_minimum
: Minimum release voltage of Low-Voltage detection reset.
See "12.10. Low-Voltage Detection Characteristics"
Document Number: 002-05625 Rev.*A
Page 52 of 87
MB9A310K Series
12.4.8 Base Timer Input Timing
Timer input timing
Parameter
Input pulse width
Symbol
(Vcc = 2.7V to 5.5V, Vss = 0V, Ta = - 40°C to + 105°C)
Value
Unit
Remarks
Min
Max
Pin name
Conditions
TIOAn/TIOBn
(when using as ECK,
TIN)
tTIWH
tTIWL
-
tTIWH
2tCYCP
-
ns
tTIWL
ECK
VIHS
TIN
VIHS
VILS
VILS
Trigger input timing
Parameter
Input pulse width
Symbol
tTRGH
tTRGL
(Vcc = 2.7V to 5.5V, Vss = 0V, Ta = - 40°C to + 105°C)
Value
Conditions
Unit
Remarks
Min
Max
Pin name
TIOAn/TIOBn
(when using as
TGIN)
-
tTRGH
TGIN
VIHS
2tCYCP
-
ns
tTRGL
VIHS
VILS
VILS
Note: tCYCP indicates the APB bus clock cycle time.
About the APB bus number which UART is connected to, see "Block Diagram" in this datasheet.
Document Number: 002-05625 Rev.*A
Page 53 of 87
MB9A310K Series
12.4.9 CSIO/UART Timing
CSIO (SPI = 0, SCINV = 0)
Parameter
Symbol
Serial clock cycle time
tSCYC
SCK ↓ → SOT delay time
tSLOVI
SIN → SCK ↑ setup time
tIVSHI
SCK ↑ → SIN hold time
tSHIXI
Serial clock "L" pulse width
Serial clock "H" pulse width
tSLSH
tSHSL
SCK ↓ → SOT delay time
tSLOVE
SIN → SCK ↑ setup time
tIVSHE
SCK ↑ → SIN hold time
tSHIXE
SCK fall time
SCK rise time
tF
tR
Pin
name
SCKx
SCKx
SOTx
SCKx
SINx
SCKx
SINx
SCKx
SCKx
SCKx
SOTx
SCKx
SINx
SCKx
SINx
SCKx
SCKx
Conditions
Master mode
Slave mode
(Vcc = 2.7V to 5.5V, Vss = 0V, Ta = - 40°C to + 105°C)
Vcc < 4.5V
Vcc ≥ 4.5V
Unit
Min
Max
Min
Max
4tcycp
-
4tcycp
-
ns
-30
+30
- 20
+ 20
ns
50
-
30
-
ns
0
-
0
-
ns
2tcycp - 10
tcycp + 10
-
2tcycp - 10
tcycp + 10
-
ns
ns
-
50
-
30
ns
10
-
10
-
ns
20
-
20
-
ns
-
5
5
-
5
5
ns
ns
Notes:
• The above characteristics apply to CLK synchronous mode.
• tCYCP indicates the APB bus clock cycle time.
About the APB bus number which Multi-function Serial is connected to, see "Block Diagram" in this Datasheet.
• These characteristics only guarantee the same relocate port number.
For example, the combination of SCKx_0 and SOTx_1 is not guaranteed.
• When the external load capacitance = 30 pF.
Document Number: 002-05625 Rev.*A
Page 54 of 87
MB9A310K Series
tSCYC
VOH
SCK
VOL
VOL
tSLOVI
VOH
VOL
SOT
tIVSHI
SIN
VIH
VIL
tSHIXI
VIH
VIL
Master mode
tSLSH
SCK
VIH
tF
SOT
VIL
tSHSL
VIH
VIL
VIH
tR
tSLOVE
VOH
VOL
SIN
tIVSHE
VIH
VIL
tSHIXE
VIH
VIL
Slave mode
Document Number: 002-05625 Rev.*A
Page 55 of 87
MB9A310K Series
CSIO (SPI = 0, SCINV = 1)
Parameter
Serial clock cycle time
Symbol
Pin
name
(Vcc = 2.7V to 5.5V, Vss = 0V, Ta = - 40°C to + 105°C)
Vcc < 4.5V
Vcc ≥ 4.5V
Conditions
Unit
Min
Max
Min
Max
tSCYC
SCKx
4tcycp
-
4tcycp
-
Ns
SCK ↑ → SOT delay time
tSHOVI
SCKx
SOTx
-30
+30
- 20
+ 20
Ns
SIN → SCK ↓ setup time
tIVSLI
50
-
30
-
Ns
SCK ↓ → SIN hold time
tSLIXI
0
-
0
-
Ns
Serial clock "L" pulse width
Serial clock "H" pulse width
tSLSH
tSHSL
2tcycp - 10
tcycp + 10
-
2tcycp - 10
tcycp + 10
-
Ns
Ns
SCK ↑ → SOT delay time
tSHOVE
-
50
-
30
ns
SIN → SCK ↓ setup time
tIVSLE
10
-
10
-
ns
SCK ↓ → SIN hold time
tSLIXE
20
-
20
-
ns
SCK fall time
SCK rise time
tF
tR
-
5
5
-
5
5
ns
ns
SCKx
SINx
SCKx
SINx
SCKx
SCKx
SCKx
SOTx
SCKx
SINx
SCKx
SINx
SCKx
SCKx
Master mode
Slave mode
Notes:
• The above characteristics apply to CLK synchronous mode.
• tCYCP indicates the APB bus clock cycle time.
About the APB bus number which Multi-function Serial is connected to, see "Block Diagram" in this Datasheet.
• These characteristics only guarantee the same relocate port number.
For example, the combination of SCKx_0 and SOTx_1 is not guaranteed.
• When the external load capacitance = 30 pF.
Document Number: 002-05625 Rev.*A
Page 56 of 87
MB9A310K Series
tSCYC
VOH
SCK
VOH
VOL
tSHOVI
VOH
VOL
SOT
tIVSLI
SIN
VIH
VIL
tSLIXI
VIH
VIL
Master mode
tSHSL
SCK
tSLSH
VIH
VIH
VIL
tR
VIL
tF
tSHOVE
SOT
SIN
VIL
VOH
VOL
tIVSLE
VIH
VIL
tSLIXE
VIH
VIL
Slave mode
Document Number: 002-05625 Rev.*A
Page 57 of 87
MB9A310K Series
CSIO (SPI = 1, SCINV = 0)
(Vcc = 2.7V to 5.5V, Vss = 0V, Ta = - 40°C to + 105°C)
Parameter
Serial clock cycle time
Symbol
Pin
name
Vcc ≥ 4.5V
Min
Max
Vcc < 4.5V
Min
Max
Conditions
Unit
tSCYC
SCKx
4tcycp
-
4tcycp
-
ns
SCK ↑ → SOT delay time
tSHOVI
SCKx
SOTx
-30
+30
- 20
+ 20
ns
SIN → SCK ↓ setup time
tIVSLI
50
-
30
-
ns
SCK ↓ → SIN hold time
tSLIXI
0
-
0
-
ns
SOT → SCK ↓ delay time
tSOVLI
2tcycp - 30
-
2tcycp - 30
-
ns
Serial clock "L" pulse width
Serial clock "H" pulse width
tSLSH
tSHSL
2tcycp - 10
tcycp + 10
-
2tcycp - 10
tcycp + 10
-
ns
ns
SCK ↑ → SOT delay time
tSHOVE
-
50
-
30
ns
SIN → SCK ↓ setup time
tIVSLE
10
-
10
-
ns
SCK ↓ → SIN hold time
tSLIXE
20
-
20
-
ns
SCK fall time
SCK rise time
tF
tR
-
5
5
-
5
5
ns
ns
SCKx
SINx
SCKx
SINx
SCKx
SOTx
SCKx
SCKx
SCKx
SOTx
SCKx
SINx
SCKx
SINx
SCKx
SCKx
Master mode
Slave mode
Notes:
• The above characteristics apply to CLK synchronous mode.
• tCYCP indicates the APB bus clock cycle time.
About the APB bus number which Multi-function Serial is connected to, see "Block Diagram" in this Datasheet.
• These characteristics only guarantee the same relocate port number.
For example, the combination of SCKx_0 and SOTx_1 is not guaranteed.
• When the external load capacitance = 30 pF.
Document Number: 002-05625 Rev.*A
Page 58 of 87
MB9A310K Series
tSCYC
VOH
VOL
SCK
VOH
VOL
SOT
VOH
VOL
tIVSLI
tSLIXI
VIH
VIL
SIN
VOL
tSHOVI
tSOVLI
VIH
VIL
Master mode
tSLSH
SCK
VIH
VIH
VIL
tF
*
SOT
VIL
tSHSL
tR
VIH
tSHOVE
VOH
VOL
VOH
VOL
tIVSLE
SIN
tSLIXE
VIH
VIL
VIH
VIL
Slave mode
Changes when writing to TDR register
Document Number: 002-05625 Rev.*A
Page 59 of 87
MB9A310K Series
CSIO (SPI = 1, SCINV = 1)
Parameter
Symbol
Pin
name
(Vcc = 2.7V to 5.5V, Vss = 0V, Ta = - 40°C to + 105°C)
Vcc < 4.5V
Vcc ≥ 4.5V
Conditions
Unit
Min
Max
Min
Max
Serial clock cycle time
tSCYC
SCKx
4tcycp
-
4tcycp
-
ns
SCK ↓ → SOT delay time
tSLOVI
SCKx
SOTx
-30
+30
- 20
+ 20
ns
SIN → SCK ↑ setup time
tIVSHI
50
-
30
-
ns
SCK ↑ → SIN hold time
tSHIXI
0
-
0
-
ns
SOT → SCK ↑ delay time
tSOVHI
2tcycp - 30
-
2tcycp - 30
-
ns
Serial clock "L" pulse width
Serial clock "H" pulse width
tSLSH
tSHSL
2tcycp - 10
tcycp + 10
-
2tcycp - 10
tcycp + 10
-
ns
ns
SCK ↓→ SOT delay time
tSLOVE
-
50
-
30
ns
SIN → SCK ↑ setup time
tIVSHE
10
-
10
-
ns
SCK ↑ → SIN hold time
tSHIXE
20
-
20
-
ns
SCK fall time
SCK rise time
tF
tR
-
5
5
-
5
5
ns
ns
SCKx
SINx
SCKx
SINx
SCKx
SOTx
SCKx
SCKx
SCKx
SOTx
SCKx
SINx
SCKx
SINx
SCKx
SCKx
Master mode
Slave mode
Notes:
• The above characteristics apply to CLK synchronous mode.
• tCYCP indicates the APB bus clock cycle time.
About the APB bus number which Multi-function Serial is connected to, see "Block Diagram" in this datasheet.
• These characteristics only guarantee the same relocate port number.
For example, the combination of SCKx_0 and SOTx_1 is not guaranteed.
• When the external load capacitance = 30 pF.
Document Number: 002-05625 Rev.*A
Page 60 of 87
MB9A310K Series
tSCYC
VOH
SCK
tSOVHI
tSLOVI
VOH
VOL
SOT
VOH
VOL
tSHIXI
tIVSHI
VIH
VIL
SIN
VOH
VOL
VIH
VIL
Master mode
tSHSL
tR
SCK
VIL
tSLSH
VIH
VIH
tF
VIL
VIH
VIL
tSLOVE
VOH
VOL
SOT
VOH
VOL
tIVSHE
tSHIXE
VIH
VIL
SIN
VIH
VIL
Slave mode
UART external clock (EXT = 1)
(Vcc = 2.7V to 5.5V, Vss = 0V, Ta = - 40°C to + 105°C)
Parameter
Serial clock "L" pulse width
Serial clock "H" pulse width
SCK fall time
SCK rise time
Symbol
tSLSH
tSHSL
tF
tR
Conditions
VIL
Document Number: 002-05625 Rev.*A
tSHSL
VIH
Max
tcycp + 10
tcycp + 10
-
CL = 30 pF
tR
SCK
Min
5
5
VIL
Remarks
ns
ns
ns
ns
tF
tSLSH
VIH
Unit
VIL
VIH
Page 61 of 87
MB9A310K Series
12.4.10 External Input Timing
Parameter
Symbol
Pin name
Conditions
(Vcc = 2.7V to 5.5V, Vss = 0V, Ta = - 40°C to + 105°C)
Value
Unit
Remarks
Min
Max
ADTG
Input pulse width
tINH,
tINL
FRCKx
ICxx
DTTIxX
INTxx
NMIX
WKUPx
A/D converter trigger input
-
2tCYCP[1]
-
ns
[2]
[3]
-[4]
2tCYCP[1]
2tCYCP + 100[1]
500
820
-
ns
ns
ns
ns
Free-run timer input clock
Input capture
Wave form generator
External interrupt
NMI
Deep stand-by wake up
[1]: tCYCP indicates the APB bus clock cycle time.
About the APB bus number which A/D converter, Multi-function Timer, External interrupt are connected to, see "Block Diagram"
in this Datasheet.
[2]: When in run mode, in sleep mode.
[3]: When in stop mode, in rtc mode, in timer mode.
[4]: When in deep stand-by stop mode, in deep stand-by rtc mode.
Document Number: 002-05625 Rev.*A
Page 62 of 87
MB9A310K Series
12.4.11 Quadrature Position/Revolution Counter timing
(Vcc = 2.7V to 5.5V, Vss = 0V, Ta = - 40°C to + 105°C)
Parameter
AIN pin "H" width
AIN pin "L" width
BIN pin "H" width
BIN pin "L" width
BIN rise time from
AIN pin "H" level
AIN fall time from
BIN pin "H" level
BIN fall time from
AIN pin "L" level
AIN rise time from
BIN pin "L" level
AIN rise time from
BIN pin "H" level
BIN fall time from
AIN pin "H" level
AIN fall time from
BIN pin "L" level
BIN rise time from
AIN pin "L" level
ZIN pin "H" width
ZIN pin "L" width
AIN/BIN rise and fall time from
determined ZIN level
Determined ZIN level from AIN/BIN
rise and fall time
Symbol
Conditions
tAHL
tALL
tBHL
tBLL
-
tAUBU
PC_Mode2 or PC_Mode3
tBUAD
PC_Mode2 or PC_Mode3
tADBD
PC_Mode2 or PC_Mode3
tBDAU
PC_Mode2 or PC_Mode3
tBUAU
PC_Mode2 or PC_Mode3
tAUBD
PC_Mode2 or PC_Mode3
tBDAD
PC_Mode2 or PC_Mode3
tADBU
PC_Mode2 or PC_Mode3
tZHL
tZLL
QCR:CGSC = "0"
QCR:CGSC = "0"
tZABE
QCR:CGSC = "1"
tABEZ
QCR:CGSC = "1"
Value
Min
Max
2tCYCP[1]
-
Unit
ns
[1]: tCYCP indicates the APB bus clock cycle time.
About the APB bus number which Quadrature Position/Revolution Counter is connected to, see "Block Diagram" in this
Datasheet.
tALL
tAHL
AIN
tAUBU
tADBD
tBUAD
tBDAU
BIN
tBHL
Document Number: 002-05625 Rev.*A
tBLL
Page 63 of 87
MB9A310K Series
tBLL
tBHL
BIN
tBUAU
tBDAD
tAUBD
tADBU
AIN
tAHL
tALL
ZIN
ZIN
AIN/BIN
Document Number: 002-05625 Rev.*A
Page 64 of 87
MB9A310K Series
2
12.4.12 I C Timing
(Vcc = 2.7V to 5.5V, Vss = 0V, Ta = - 40°C to + 105°C)
Parameter
SCL clock frequency
(Repeated) START condition hold time
SDA ↓→ SCL ↓
SCLclock "L" width
SCLclock "H" width
(Repeated) START setup time
SCL ↑→ SDA ↓
Data hold time
SCL ↓→ SDA ↓ ↑
Data setup time
SDA ↓ ↑ → SCL ↑
STOP condition setup time
SCL ↑→ SDA ↑
Bus free time between
"STOP condition" and
"START condition"
Noise filter
Symbol
Conditions
Standard-mode
Min
Max
Fast-mode
Min
Max
Un
it
FSCL
0
100
0
400
kH
z
tHDSTA
4.0
-
0.6
-
μs
tLOW
tHIGH
4.7
4.0
-
1.3
0.6
-
μs
μs
4.7
-
0.6
-
μs
0
3.45[2]
0
0.9[3]
μs
tSUDAT
250
-
100
-
ns
tSUSTO
4.0
-
0.6
-
μs
tBUF
4.7
-
1.3
-
μs
2 tCYCP[4]
-
2 tCYCP[4]
-
ns
tSUSTA
tHDDAT
tSP
CL = 30pF,
R = (Vp/IOL) [1]
-
Remarks
1. R and C represent the pull-up resistance and load capacitance of the SCL and SDA lines, respectively.
Vp indicates the power supply voltage of the pull-up resistance and IOL indicates VOL guaranteed current.
2. The maximum tHDDAT must satisfy that it doesn't extend at least "L" period (t LOW) of device's SCL signal.
2
2
3. Fast-mode I C bus device can be used on Standard-mode I C bus system as long as the device satisfies the requirement of
"tSUDAT ≥ 250 ns".
4. tCYCP is the APB bus clock cycle time.
About the APB bus number that I2C is connected to, see "Block Diagram" in this Datasheet.
To use Standard-mode, set the APB bus clock at 2 MHz or more.
To use Fast-mode, set the APB bus clock at 8 MHz or more.
SDA
SCL
Document Number: 002-05625 Rev.*A
Page 65 of 87
MB9A310K Series
12.4.13 JTAG Timing
(Vcc = 2.7V to 5.5V, Vss = 0V, Ta = - 40°C to + 105°C)
Parameter
Symbol
Pin name
Conditions
TMS, TDI setup time
tJTAGS
TCK,
TMS, TDI
Vcc ≥ 4.5V
TMS, TDI hold time
tJTAGH
TCK,
TMS, TDI
Vcc ≥ 4.5V
TDO delay time
tJTAGD
TCK,
TDO
Min
Value
Max
Unit
15
-
ns
15
-
ns
Vcc ≥ 4.5V
-
25
Vcc < 4.5V
-
45
Vcc < 4.5V
Vcc < 4.5V
Remarks
ns
Note: When the external load capacitance = 30 pF.
TCK
TMS/TDI
TDO
Document Number: 002-05625 Rev.*A
Page 66 of 87
MB9A310K Series
12.5 12-bit A/D Converter
Electrical characteristics for the A/D converter
(Vcc = AVcc = 2.7V to 5.5V, Vss = AVss = 0V, Ta = - 40°C to + 105°C)
Symbol
Pin
name
Resolution
Integral nonlinearity
Differential nonlinearity
Zero transition voltage
VZT
ANxx
Full-scale transition voltage
VFST
ANxx
-
-
Ts
-
Compare clock cycle[3]
Tcck
State transition time to
operation permission
Parameter
Min
Value
Typ
Max
Unit
Remarks
AVRH = 2.7V to 5.5V
- 4.5
-2.5
- 20
AVRH 20
1.0[1]
1.2[1]
-
12
+ 4.5
+ 2.5
+ 20
bit
LSB
LSB
mV
-
AVRH + 20
mV
-
-
μs
[2]
-
-
[2]
-
-
-
50
-
2000
ns
Tstt
-
-
-
1.0
μs
Analog input capacity
CAIN
-
-
-
12.9
pF
Analog input resistance
RAIN
-
-
-
Interchannel disparity
Analog port input current
-
ANxx
-
Analog input voltage
-
ANxx
Reference voltage
-
AVRH
Conversion time
Sampling time
2
ns
kΩ
-
3.8
4
5
LSB
μA
AVSS
-
AVRH
V
2.7
-
AVCC
V
AVcc ≥ 4.5V
AVcc < 4.5V
AVcc ≥ 4.5V
AVcc < 4.5V
AVcc ≥ 4.5V
AVcc < 4.5V
[1]: Conversion time is the value of sampling time (Ts) + compare time (Tc).
The condition of the minimum conversion time is the following.
AVcc ≥ 4.5V, HCLK = 40 MHz
sampling time: 300 ns, compare time: 700 ns
AVcc < 4.5V, HCLK = 40 MHz
sampling time: 500 ns, compare time: 700 ns
Ensure that it satisfies the value of sampling time (Ts) and compare clock cycle (Tcck).
4
For setting* of sampling time and compare clock cycle, see "Chapter 1-1:A/D Converter" in "FM3 Famliy Peripheral Manual
Analog Macro Part".
The A/D Converter register is set at APB bus clock timing. The sampling clock and compare clock are set at Base clock (HCLK).
About the APB bus number which the A/D Converter is connected to, see "Block Diagram" in this Datasheet.
[2]: A necessary sampling time changes by external impedance.
Ensure that it set the sampling time to satisfy (Equation 1).
[3]: Compare time (Tc) is the value of (Equation 2).
Document Number: 002-05625 Rev.*A
Page 67 of 87
MB9A310K Series
Rext
ANxx
Analog input pin
Comparator
RAIN
Analog signal
source
CAIN
(Equation 1) Ts ≥ ( RAIN + Rext ) × CAIN × 9
Ts
: Sampling time
RAIN
: input resistance of A/D = 2kΩ at 4.5 < AVCC < 5.5
input resistance of A/D = 3.8kΩ at 2.7 < AVCC < 4.5
CAIN
: input capacity of A/D = 12.9pF at 2.7 < AVCC < 5.5
Rext
: Output impedance of external circuit
(Equation 2) Tc = Tcck × 14
Tc
: Compare time
Tcck
: Compare clock cycle
Document Number: 002-05625 Rev.*A
Page 68 of 87
MB9A310K Series
Definition of 12-bit A/D Converter Terms
Resolution
: Analog variation that is recognized by an A/D converter.
Integral nonlinearity
: Deviation of the line between the zero-transition point
(0b000000000000←→0b000000000001) and the full-scale transition point
(0b111111111110←→0b111111111111) from the actual conversion characteristics.
Differential nonlinearity : Deviation from the ideal value of the input voltage that is required to change the
output code by 1 LSB.
Integral nonlinearity
Differential nonlinearity
0xFFF
Actual conversion
characteristics
0xFFE
Actual conversion
characteristics
0x(N+1)
{1 LSB(N-1) + VZT}
VFST
VNT
0x004
(Actuallymeasured
value)
(Actually-measured
value)
0x003
Digital output
Digital output
0xFFD
0xN
Ideal characteristics
V(N+1)T
0x(N-1)
(Actually-measured
value)
Actual conversion
characteristics
Ideal characteristics
0x002
VNT
(Actually-measured
value)
0x(N-2)
0x001
VZT (Actually-measured value)
AVss
Actual conversion characteristics
AVRH
AVss
Analog input
Integral nonlinearity of digital output N =
Differential nonlinearity of digital output N =
1LSB =
N
VZT
VFST
VNT
:
:
:
:
AVRH
Analog input
VNT - {1LSB × (N - 1) + VZT}
1LSB
V(N + 1) T - VNT
1LSB
[LSB]
- 1 [LSB]
VFST - VZT
4094
A/D converter digital output value.
Voltage at which the digital output changes from 0x000 to 0x001.
Voltage at which the digital output changes from 0xFFE to 0xFFF.
Voltage at which the digital output changes from 0x(N − 1) to 0xN.
Document Number: 002-05625 Rev.*A
Page 69 of 87
MB9A310K Series
12.6 USB Characteristics
(Vcc = 2.7V to 5.5V, USBVcc = 3.0V to 3.6V, Vss = 0V, Ta = - 40°C to + 105°C)
Parameter
Input "H" level voltage
Input "L" level voltage
Input
charact-eris
Differential input sensitivity
tics
Different common mode input
voltage
Output "H" level voltage
Output "L" level voltage
Output
charact-erst Crossover voltage
Rise time
ics
Fall time
Rise/ fall time matching
Output impedance
Rise time
Fall time
Rise/ fall time matching
Symbol
Pin
name
Value
Conditions
Min
Max
Unit
Remarks
VIH
-
2.0
USBVcc + 0.3
V
[1]
VIL
-
Vss - 0.3
0.8
V
[1]
VDI
-
0.2
-
V
[2]
VCM
-
0.8
2.5
V
[2]
2.8
3.6
V
[3]
0.0
0.3
V
[3]
1.3
4
4
90
28
75
75
80
2.0
20
20
111.11
44
300
300
125
V
ns
ns
%
Ω
ns
ns
%
[4]
[5]
[5]
[5]
[6]
[7]
[7]
[7]
VOH
VOL
VCRS
tFR
tFF
tFRFM
ZDRV
tLR
tLF
tLRFM
UDP0,
UDM0
External
pull-down
resistance
= 15kΩ
External pull-up
resistance
= 1.5kΩ
Full-Speed
Full-Speed
Full-Speed
Full-Speed
Low-Speed
Low-Speed
Low-Speed
[1]: The switching threshold voltage of Single-End-Receiver of USB I/O buffer is set as within VIL (Max) = 0.8V,
VIH (Min) = 2.0 V (TTL input standard).
There are some hysteresis to lower noise sensitivity.
Minimum differential input
sensitivity [V]
[2]: Use differential-Receiver to receive USB differential data signal.
Differential-Receiver has 200 mV of differential input sensitivity when the differential data input is within 0.8 V to 2.5 V to the local
ground reference level.
Above voltage range is the common mode input voltage range.
Common mode input voltage [V]
Document Number: 002-05625 Rev.*A
Page 70 of 87
MB9A310K Series
[3]: The output drive capability of the driver is below 0.3 V at Low-State (VOL) (to 3.6 V and 1.5 kΩ load), and 2.8 V or above (to the
VSS and 1.5 kΩ load) at High-State (VOH).
[4]: The cross voltage of the external differential output signal (D + /D − ) of USB I/O buffer is within 1.3 V to 2.0 V.
VCRS specified range
[5]: They indicate rise time (Trise) and fall time (Tfall) of the full-speed differential data signal.
They are defined by the time between 10% and 90% of the output signal voltage.
For full-speed buffer, Tr/Tf ratio is regulated as within ± 10% to minimize RFI emission.
Rising time
Document Number: 002-05625 Rev.*A
Falling time
Page 71 of 87
MB9A310K Series
[6]: USB Full-speed connection is performed via twist pair cable shield with 90Ω ± 15% characteristic impedance (Differential Mode).
USB standard defines that output impedance of USB driver must be in range from 28Ω to 44Ω. So, discrete series resistor (Rs)
addition is defined in order to satisfy the above definition and keep balance.
When using this USB I/O, use it with 25Ω to 30Ω (recommendation value 27Ω) Series resistor Rs.
28Ω to 44Ω Equiv. Imped.
28Ω to 44Ω Equiv. Imped.
Mount it as external resistance.
Rs series resistor 25Ω to 30Ω
Series resistor of 27Ω (recommendation value) must be added.
And, use "resistance with an uncertainty of 5% by E24 sequence".
[7]: They indicate rise time (Trise) and fall time (Tfall) of the low-speed differential data signal.
They are defined by the time between 10% and 90% of the output signal voltage.
Rising time
Falling time
See Figure "Low-Speed Load (Compliance Load)" for conditions of external load.
Document Number: 002-05625 Rev.*A
Page 72 of 87
MB9A310K Series
Low-Speed Load (Upstream Port Load) - Reference 1
CL = 50pF to 150pF
CL = 50pF to 150pF
Low-Speed Load (Downstream Port Load) - Reference 2
CL = 200pF to
600pF
CL = 200pF to
600pF
Low-Speed Load (Compliance Load)
CL
=
200pF to 450pF
CL = 200pF to 450pF
Document Number: 002-05625 Rev.*A
Page 73 of 87
MB9A310K Series
12.7 Low-voltage Detection Characteristics
12.7.1 Low-voltage Detection Reset
(Ta = - 40°C to + 105°C)
Parameter
Detected voltage
Released voltage
Symbol
Conditions
VDL
VDH
-
Min
Value
Typ
Max
2.25
2.30
2.45
2.50
2.65
2.70
Unit
Remarks
V
V
When voltage drops
When voltage rises
12.7.2 Interrupt of Low-voltage Detection
(Ta = - 40°C to + 105°C)
Parameter
Symbol
Detected voltage
Released voltage
Detected voltage
VDL
VDH
VDL
Released voltage
VDH
Detected voltage
VDL
Released voltage
VDH
Detected voltage
VDL
Released voltage
VDH
Detected voltage
VDL
Released voltage
VDH
Detected voltage
VDL
Released voltage
VDH
Detected voltage
VDL
Released voltage
VDH
Detected voltage
VDL
Released voltage
VDH
LVD stabilization wait time
TLVDW
Conditions
SVHI = 0000
SVHI = 0001
SVHI = 0010
SVHI = 0011
SVHI = 0100
SVHI = 0111
SVHI = 1000
SVHI = 1001
-
Min
Value
Typ
Max
Unit
Remarks
When voltage drops
When voltage rises
When voltage drops
2.58
2.67
2.76
2.8
2.9
3.0
3.02
3.13
3.24
V
V
V
2.85
3.1
3.34
V
When voltage rises
2.94
3.2
3.45
V
When voltage drops
3.04
3.3
3.56
V
When voltage rises
3.31
3.6
3.88
V
When voltage drops
3.40
3.7
3.99
V
When voltage rises
3.40
3.7
3.99
V
When voltage drops
3.50
3.8
4.10
V
When voltage rises
3.68
4.0
4.32
V
When voltage drops
3.77
4.1
4.42
V
When voltage rises
3.77
4.1
4.42
V
When voltage drops
3.86
4.2
4.53
V
When voltage rises
3.86
4.2
4.53
V
When voltage drops
3.96
4.3
4.64
V
When voltage rises
-
-
2240 ×
tcycp[1]
μs
[1]: tCYCP indicates the APB2 bus clock cycle time.
Document Number: 002-05625 Rev.*A
Page 74 of 87
MB9A310K Series
12.8 MainFlash Memory Write/Erase Characteristics
12.8.1 Write / Erase time
(Vcc = 2.7V to 5.5V, Ta = - 40°C to + 105°C)
Value
Parameter
Unit
Remarks
s
Includes write time prior to internal erase
384
μs
Not including system-level overhead time
16.2
s
Includes write time prior to internal erase
Typ*
Max[1]
Large Sector
0.7
3.7
Small Sector
0.3
1.1
Half word (16-bit)
write time
12
Chip erase time
3.8
Sector erase time
[1]: The typical value is immediately after shipment, the maximam value is guarantee value under 100,000 cycle of erase/write.
12.8.2 Erase/write cycles and data hold time
Erase/write cycles (cycle)
Data hold time (year)
1,000
20[1]
10,000
10[1]
100,000
5[1]
[1]: At average + 85°C
12.9 WorkFlash Memory Write/Erase Characteristics
12.9.1 Write / Erase time
(Vcc = 2.7V to 5.5V, Ta = - 40°C to + 105°C)
Value
Parameter
Unit
Remarks
1.5
s
Includes write time prior to internal erase
20
384
μs
Not including system-level overhead time
1.2
6
s
Includes write time prior to internal erase
Typ*
Max[1]
Sector erase time
0.3
Half word (16-bit)
write time
Chip erase time
[1]: The typical value is immediately after shipment, the maximam value is guarantee value under 10,000 cycle of erase/write.
12.9.2 Erase/write cycles and data hold time
Erase/write cycles (cycle)
Data hold time (year)
1,000
20[1]
10,000
10[1]
[1]: At average + 85°C
Document Number: 002-05625 Rev.*A
Page 75 of 87
MB9A310K Series
12.10 Return Time from Low-Power Consumption Mode
12.10.1 Return Factor: Interrupt/WKUP
The return time from Low-Power consumption mode is indicated as follows. It is from receiving the return factor to starting the
program operation.
Return Count Time
(VCC = 2.7V to 5.5V, Ta = - 40°C to + 105°C)
Value
Parameter
Symbol
Max[1]
Typ
SLEEP mode
tCYCC
High-speed CR TIMER mode,
Main TIMER mode,
PLL TIMER mode
Unit
ns
40
80
μs
370
740
μs
Sub TIMER mode
699
929
μs
STOP mode
505
834
μs
Low-speed CR TIMER mode
Ticnt
Remarks
[1]: The maximum value depends on the accuracy of built-in CR.
Operation example of return from Low-Power consumption mode (by external interrupt[1])
Ext.INT
Interrupt factor
accept
Active
Ticnt
CPU
Operation
Interrupt factor
clear by CPU
Start
[1]: External interrupt is set to detecting fall edge.
Document Number: 002-05625 Rev.*A
Page 76 of 87
MB9A310K Series
Operation example of return from Low-Power consumption mode (by internal resource interrupt[1])
Internal
Resource INT
Interrupt factor
accept
Active
Ticnt
CPU
Operation
Interrupt factor
clear by CPU
Start
[1]: Internal resource interrupt is not included in return factor by the kind of Low-Power consumption mode.
Notes:
• The return factor is different in each Low-Power consumption modes.
• See "Chapter 6: Low Power Consumption Mode" and "Operations of Standby Modes" in FM3 Family Peripheral Manual
about the return factor from Low-Power consumption mode.
• When interrupt recoveries, the operation mode that CPU recoveries depends on the state before the Low-Power
consumption mode transition. See "Chapter 6: Low Power Consumption Mode" in "FM3 Family Peripheral Manual".
Document Number: 002-05625 Rev.*A
Page 77 of 87
MB9A310K Series
12.11 Return Factor: Reset
The return time from Low-Power consumption mode is indicated as follows. It is from releasing reset to starting the program
operation.
12.11.1 Return Count Time
(VCC = 2.7V to 5.5V, Ta = - 40°C to + 105°C)
Parameter
Value
Symbol
Typ
Max[1]
Unit
365
554
μs
365
554
μs
555
934
μs
Sub TIMER mode
608
976
μs
STOP mode
475
774
μs
SLEEP mode
High-speed CR TIMER mode,
Main TIMER mode,
PLL TIMER mode
Low-speed CR TIMER mode
Trcnt
Remarks
[1]: The maximum value depends on the accuracy of built-in CR.
Operation example of return from Low-Power consumption mode (by INITX)
INITX
Internal RST
RST Active
Release
Trcnt
CPU
Operation
Document Number: 002-05625 Rev.*A
Start
Page 78 of 87
MB9A310K Series
Operation example of return from low power consumption mode (by internal resource reset[1])
Internal
Resource RST
Internal RST
RST Active
Release
Trcnt
CPU
Operation
[1]: Internal resource reset
Start
is not included in return factor by the kind of Low-Power consumption mode.
Notes:
• The return factor is different in each Low-Power consumption modes.
See "Chapter 6: Low Power Consumption Mode" and "Operations of Standby Modes" in FM3 Family Peripheral Manual.
• When interrupt recoveries, the operation mode that CPU recoveries depends on the state before the Low-Power
consumption mode transition. See "Chapter 6: Low Power Consumption Mode" in "FM3 Family Peripheral Manual".
• The time during the power-on reset/low-voltage detection reset is excluded. See "(6) Power-on Reset Timing in 4. AC
Characteristics in Electrical Characteristics" for the detailon the time during the power-on reset/low -voltage detection reset.
• When in recovery from reset, CPU changes to the high-speed CR run mode. When using the main clock or the PLL clock, it
is necessary to add the main clock oscillation stabilization wait time or the main PLL clock stabilization wait time.
• The internal resource reset means the watchdog reset and the CSV reset.
Document Number: 002-05625 Rev.*A
Page 79 of 87
MB9A310K Series
13. Ordering Information
Part number
MB9AF311KPMC-G-JNE2
MB9AF312KPMC-G-JNE2
MB9AF311KPMC1-G-JNE2
MB9AF312KPMC1-G-JNE2
MB9AF311KQN-G-AVE2
MB9AF312KQN-G-AVE2
Document Number: 002-05625 Rev.*A
On-chip
Flash
memory
Main: 64 Kbyte
Work: 32 Kbyte
Main: 128 Kbyte
Work: 32 Kbyte
Main: 64 Kbyte
Work: 32 Kbyte
Main: 128 Kbyte
Work: 32 Kbyte
Main: 64 Kbyte
Work: 32 Kbyte
Main: 128 Kbyte
Work: 32 Kbyte
On-chip
SRAM
16 Kbyte
16 Kbyte
16 Kbyte
16 Kbyte
16 Kbyte
16 Kbyte
Package
Packing
Plastic LQFP
48-pin (0.5mm pitch),
(FPT-48P-M49)
Plastic LQFP
52-pin (0.65mm pitch),
(FPT-52P-M02)
Tray
Plastic QFN
48-pin (0.5mm pitch),
(LCC-48P-M73)
Page 80 of 87
MB9A310K Series
14. Package Dimensions
48-pin plastic LQFP
Lead pitch
0.50 mm
Package width ×
package length
7.00 mm × 7.00 mm
Lead shape
Gullwing
Lead bend
direction
Normal bend
Sealing method
Plastic mold
Mounting height
1.70 mm MAX
Weight
0.17 g
(FPT-48P-M49)
48-pin plastic LQFP
(FPT-48P-M49)
Note 1) * : These dimensions do not include resin protrusion.
Note 2) Pins width and pins thickness include plating thickness.
Note 3) Pins width do not include tie bar cutting remainder.
9.00 ± 0.20(.354 ± .008)SQ
*7.00± 0.10(.276 ± .004)SQ
36
0.145± 0.055
(.006 ± .002)
25
37
24
0.08(.003)
Details of "A" part
+0.20
1.50 –0.10 (Mounting height)
+.008
.059 –.004
INDEX
48
13
"A"
0°~8°
1
0.50(.020)
C
12
0.22 ± 0.05
(.008 ± .002)
0.08(.003)
2010 FUJITSU SEMICONDUCTOR LIMITED HMbF48-49Sc-1-2
Document Number: 002-05625 Rev.*A
0.10 ± 0.10
(.004 ± .004)
(Stand off)
0.25(.010)
M
0.60 ± 0.15
(.024 ± .006)
Dimensions in mm (inches).
Note: The values in parentheses are reference values.
Page 81 of 87
MB9A310K Series
Document Number: 002-05625 Rev.*A
Page 82 of 87
MB9A310K Series
Document Number: 002-05625 Rev.*A
Page 83 of 87
MB9A310K Series
15. Major Changes
Spansion Publication Number: MB9A310K_DS706-00029
Page
Section
Revision 1.0
Product lineup
7
function
Packages
8
I/O Circuit Type
23
Change Results
PRELIMINARY → Datasheet
Added the pin count.
Revised from "Planning".
Corrected the following description to "TypeB".
Digital output → Digital input
Block Diagram
Corrected the following description.
AHB (Max 40MHz) → AHB (Max 42MHz)
34
APB0 (Max 40MHz) → APB0 (Max 42MHz)
APB1 (Max 40MHz) → APB1 (Max 42MHz)
APB2 (Max 40MHz) → APB2 (Max 42MHz)
Electrical Characteristics
Revised the value of "TBD".
3. DC Characteristics
Corrected the value.
(1) Current Rating
- "Power supply current (ICCR)"
Typ: 60 → 50
45, 46
- "Power supply current (ICCRD)" (RAM hold off)
Typ: 45 → 30
- "Power supply current (ICCRD)" (RAM hold on)
Typ: 48 → 33
(9) External Input Timing
Revised the value of "TBD".
61
5. 12-bit A/D Converter
Deleted"(Preliminary value)".
66
Electrical characteristics for the A/D converter Corrected the value of "Compare clock cycle".
Max: 10000 → 2000
8. MainFlash Memory Write/Erase
Deleted"(targeted value)".
Characteristics
Erase/write cycles and data hold time
74
9. WorkFlash Memory Write/Erase
Characteristics
Erase/write cycles and data hold time
Revision 1.1
Company name and layout design change
Revision 2.0
Features
2
Added the description of PLL for USB
USB Interface
25
I/O Circuit Type
Added the description of I2C to the type of E and F
25, 26
I/O Circuit Type
Added about +B input
32
Handling Devices
Added "Stabilizing power supply voltage"
Handling Devices
Added the following description
32
Crystal oscillator circuit
"Evaluate oscillation of your using crystal oscillator by your mount board."
Handling Devices
33
Changed the description
C Pin
35
Block Diagram
Modified the block diagram
Memory Map
36
Modified the area of "Extarnal Device Area"
· Memory map(1)
Memory Map
37
Added the summary of Flash memory sector and the note
· Memory map(2)
· Added the Clamp maximum current
Electrical Characteristics
44, 45
· Added the output current of P80 and P81
1. Absolute Maximum Ratings
· Added about +B input
· Modified the minimum value of Analog reference voltage
Electrical Characteristics
46
· Added Smoothing capacitor
2. Recommended Operation Conditions
· Added the note about less than the minimum power supply voltage
Document Number: 002-05625 Rev.*A
Page 84 of 87
MB9A310K Series
Page
47-49
52
53
54
55
57-64
70
79-82
83
Section
Electrical Characteristics
3. DC Characteristics
(1) Current rating
Electrical Characteristics
4. AC Characteristics
(1) Main Clock Input Characteristics
Electrical Characteristics
4. AC Characteristics
(3) Built-in CR Oscillation Characteristics
Electrical Characteristics
4. AC Characteristics
(4-1) Operating Conditions of Main and USB
PLL
(4-2) Operating Conditions of Main PLL
Electrical Characteristics
4. AC Characteristics
(6) Power-on Reset Timing
Electrical Characteristics
4. AC Characteristics
(7) CSIO/UART Timing
Electrical Characteristics
5. 12bit A/D Converter
Electrical Characteristics
9. Return Time from Low-Power Consumption
Mode
Ordering Information
Change Results
· Changed the table format
· Added Main TIMER mode current
· Added Flash Memory Current
· Moved A/D Converter Current
Added Master clock at Ingernal operating clock frequency
Added Frequency stability time at Built-in high-speed CR
· Added Main PLL clock frequency
· Added USB clock frequency
· Added the figure of Main PLL connection and USB PLL connection
· Added Time until releasing Power-on reset
· Changed the figure of timing
· Modified from UART Timing to CSIO/UART Timing
· Changed from Internal shift clock operation to Master mode
· Changed from External shift clock operation to Slave mode
· Added the typical value of Integral Nonlinearity, Differential Nonlinearity, Zero
transition voltage and Full-scale transition voltage
· Added Conversion time at AVcc < 4.5V
· Modified Stage transition time to operation permission
· Modified the minimum value of Reference voltage
Added Return Time from Low-Power Consumption Mode
Changed the description of part number
NOTE: Please see “Document History” about later revised information.
Document Number: 002-05625 Rev.*A
Page 85 of 87
MB9A310K Series
16. Document History
®
®
Document Title: MB9A310K Series 32-bit ARM Cortex -M3, FM3 Microcontroller
Document Number: 002-05625
Revision
ECN
**
−
Orig. of
Submission
Change
Date
TOYO
02/20/2015
Description of Change
Migrated to Cypress and assigned document number 002-05625.
No change to document contents or format.
*A
5232740
TOYO
Document Number: 002-05625 Rev.*A
04/21/2016
Updated to Cypress format.
Page 86 of 87
MB9A310K Series
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the
office closest to you, visit us at Cypress Locations.
®
PSoC Solutions
Products
®
®
ARM Cortex Microcontrollers
Automotive
Clocks & Buffers
Interface
Lighting & Power Control
Memory
PSoC
Touch Sensing
USB Controllers
Wireless/RF
cypress.com/arm
cypress.com/automotive
cypress.com/clocks
PSoC 1 | PSoC 3 | PSoC 4 | PSoC 5LP
Cypress Developer Community
Forums | Projects | Videos | Blogs | Training | Components
cypress.com/interface
cypress.com/powerpsoc
cypress.com/memory
Technical Support
cypress.com/support
cypress.com/psoc
cypress.com/touch
cypress.com/usb
cypress.com/wireless
ARM and Cortex are the registered trademarks of ARM Limited in the EU and other countries.
© Cypress Semiconductor Corporation,2012-2016. This document is the property of Cypress Semiconductor Corporation and its subsidiaries, including Spansion LLC (“Cypress”). This document,
including any software or firmware included or referenced in this document (“Software”), is owned by Cypress under the intellectual property laws and treaties of the United States and other countries
worldwide. Cypress reserves all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or
other intellectual property rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of the Software,
then Cypress hereby grants you a personal, non-exclusive, nontransferable license (without the right to sublicense) (1) under its copyright rights in the Software (a) for Software provided in source
code form, to modify and reproduce the Software solely for use with Cypress hardware products, only internally within your organization, and (b) to distribute the Software in binary code form
externally to end users (either directly or indirectly through resellers and distributors), solely for use on Cypress hardware product units, and (2) under those claims of Cypress’s patents that are
infringed by the Software (as provided by Cypress, unmodified) to make, use, distribute, and import the Software solely for use with Cypress hardware products. Any other use, reproduction,
modification, translation, or compilation of the Software is prohibited.
TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE
OR ACCOMPANYING HARDWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. To the extent
permitted by applicable law, Cypress reserves the right to make changes to this document without further notice. Cypress does not assume any liability arising out of the application or use of any
product or circuit described in this document. Any information provided in this document, including any sample design information or programming code, is provided only for reference purposes. It
is the responsibility of the user of this document to properly design, program, and test the functionality and safety of any application made of this information and any resulting product. Cypress
products are not designed, intended, or authorized for use as critical components in systems designed or intended for the operation of weapons, weapons systems, nuclear installations, life-support
devices or systems, other medical devices or systems (including resuscitation equipment and surgical implants), pollution control or hazardous substances management, or other uses where the
failure of the device or system could cause personal injury, death, or property damage (“Unintended Uses”). A critical component is any component of a device or system whose failure to perform
can be reasonably expected to cause the failure of the device or system, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and you shall and hereby do release Cypress
from any claim, damage, or other liability arising from or related to all Unintended Uses of Cypress products. You shall indemnify and hold Cypress harmless from and against all claims, costs,
damages, and other liabilities, including claims for personal injury or death, arising from or related to any Unintended Uses of Cypress products.
Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, PSoC, CapSense, EZ-USB, F-RAM, and Traveo are trademarks or registered trademarks of Cypress in the
United States and other countries. For a more complete list of Cypress trademarks, visit cypress.com. Other names and brands may be claimed as property of their respective owners.
Document Number: 002-05625 Rev.*A
April 26, 2016
Page 87 of 87