S6E1B8 Series
32-bit ARM® Cortex®-M0+
FM0+ Microcontroller
The S6E1B8 Series is a series of highly integrated 32-bit microcontrollers designed for embedded controllers aiming at low power
consumption and low cost. This series has the ARM Cortex-M0+ Processor with on-chip Flash memory and SRAM, and consists of
peripheral functions such as various timers, LCD controller (LCDC), AES, ADC and communication interfaces (UART, CSIO (SPI),
2
2
I C, I S, Smart Card, and USB). The products which are described in this data sheet are placed into TYPE2-M0+ product categories
in "FM0+ Family Peripheral Manual".
Features
USB host
32-bit ARM Cortex-M0+ Core
USB
2.0 Full/Low-Speed supported
Interrupt-transfer and Isochronous-transfer
support
USB Device connected/disconnected automatically detect
IN/OUT token handshake packet automatically
Max 256-byte packet-length supported
Wake-up function supported
Bulk-transfer,
Processor version: r0p1
Maximum operating frequency: 40.8 MHz
Nested Vectored Interrupt Controller (NVIC): 1 NMI
(non-maskable interrupt) and 24 peripheral interrupt with 4
selectable interrupt priority levels
24-bit System timer (Sys Tick): System timer for OS task
management
LCD Controller (LCDC)
Selectable
from 44 SEG × 4 COM (Max) or 40 SEG × 8
COM (Max)
Internal Charge pump can generate 4.6 V at most
Internal divide resistor is contained (selectable from 10 kΩ
or 100 kΩ for the resistor value)
LCD drive power supply (bias) pin (VV4 to VV0)
Interrupt function synchronized with the LCD module frame
frequency
With blinking function
Inverted display function
Bit Band Operation
Compatible with Cortex-M3 bit band operation.
On-Chip Memory
Flash memory
Up
to 512 K+48 Kbytes
bank:
upper bank : 512 Kbytes(64 Kbytes x 8)
lower bank : 48 Kbytes(8 Kbytes x 6)
Read cycle: 0 wait-cycle
Security function for code protection
Dual
Multi-Function Serial Interface (Max 8channels)
128 bytes with Tx/Rx FIFO in all channels (The number of
FIFO steps varies depending on the settings of the
communication mode or bit length.)
SRAM
The on-chip SRAM of this series has one independent SRAM .
Up to SRAM: 60 K+4 Kbytes
4Kbytes: can retain value in Deep Standby Mode
The operation mode of each channel can be selected from
one of the following.
UART
CSIO (CSIO is known to many customers as SPI)
2
I C
USB Interface
USB interface is composed of Device and Host
PLL for USB is built-in, USB clock can be generated by
multiplication of Main clock.
UART
Full
duplex double buffer
can be enabled or disabled.
Built-in dedicated baud rate generator
External clock available as a serial clock
Various error detection functions (parity errors, framing
errors, and overrun errors)
Parity
USB Device
USB
2.0 Full-Speed supported
6 EndPoint supported
EndPoint 0 is control transfer
EndPoint 1, 2 can be selected Bulk-transfer,
Interrupt-transfer or Isochronous-transfer
EndPoint 3 to 5 can select Bulk-transfer or
Interrupt-transfer
EndPoint 1 to 5 comprise Double Buffer
The size of each EndPoint is according to the follows
EndPoint 0, 2 to 5 : 64 bytes
EndPoint 1 : 256 bytes
Max
•
•
•
•
•
•
•
Cypress Semiconductor Corporation
Document Number: 001-99223 Rev.*A
•
CSIO (also known as SPI)
198 Champion Court
Full
duplex double buffer
dedicated baud rate generator
Overrun error detection function
Serial chip select function (ch6 and ch7 only)
Data length: 5 to 16 bits
Built-in
•
San Jose, CA 95134-1709
•
408-943-2600
Revised April 7, 2016
S6E1B8 Series
I2 C
Standard-mode
(Max: 100 kbps) supported / Fast-mode
(Max 400 kbps) supported.
I2 S
Using
2
CSIO (ch.5, ch.6) and I S clock generator
Supports two transfer protocol
2
• IS
• MSB-justified
Master mode only
Descriptor System Data Transfer Controller (DSTC)
(64 Channels)
Certain ports are 5 V tolerant.
See 4. List of Pin Functions and 5. I/O Circuit Type for the
corresponding pins.
Dual Timer (32-/16-bit Down Counter)
The Dual Timer consists of two programmable 32-/16-bit down
counters. The operation mode of each timer channel can be
selected from one of the following.
Free-running mode
Periodic mode (= Reload mode)
One-shot mode
The DSTC can transfer data at high-speed without going via
Multi-Function Timer
system and, following the specified contents of the
16-bit free-run timer × 3 channels
the CPU. The DSTC adopts the Descriptor
Descriptor that has already been constructed on the
memory, can access directly the memory / peripheral device
and performs the data transfer operation.
It supports the software activation, the hardware activation,
and the chain activation functions
A/D Converter (Max: 24 Channels)
12-bit A/D Converter
Successive
approximation type
time: 1.0 μs @ 2.7 V to 3.6 V
Priority conversion available (2 levels of priority)
Scan conversion mode
Built-in FIFO for conversion data storage (for scan
conversion: 16 steps, for priority conversion: 4 steps)
Conversion
Base Timer (Max: 8 Channels)
The operation mode of each channel can be selected from one
of the following.
16-bit PWM timer
16-bit PPG timer
16/32-bit reload timer
16/32-bit PWC timer
General-Purpose I/O Port
This series can use its pin as a general-purpose I/O port when
it is not used for an external bus or a peripheral function. All
ports can be set to fast general-purpose I/O ports or slow
general-purpose I/O ports. In addition, this series has a port
relocate function that can set to which I/O port a peripheral
function can be allocated.
All ports are Fast GPIO which can be accessed by 1cycle
Capable of controlling the pull-up of each pin
The Multi-function Timer consists of the following blocks.
Input capture × 4 channels
Output compare × 6 channels
ADC start compare × 6 channel
Waveform generator × 3 channels
16-bit PPG timer × 3 channels
IGBT mode is contained.
The following function can be used to achieve the motor
control.
PWM signal output function
DC chopper waveform output function
Dead time function
Input capture function
ADC start function
DTIF (motor emergency stop) interrupt function
Real-Time Clock (RTC with Vbat)
The Real-time Clock counts
year/month/day/hour/minute/second/day of the week from year
01 to year 99.
The RTC can generate an interrupt at a specific time
(year/month/day/hour/minute/second/day of the week) and
can also generate an interrupt in a specific year, in a specific
month, on a specific day, at a specific hour or at a specific
minute.
It has a timer interrupt function generating an interrupt upon
a specific time or at specific intervals.
It can keep counting while rewriting the time.
It can count leap years automatically.
Capable of reading pin level directly
Port relocate function
Up to 102 fast general-purpose I/O ports @120-pin package
Document Number: 001-99223 Rev.*A
Page 2 of 129
S6E1B8 Series
Watch Counter
The Watch Counter wakes up the microcontroller from the low
power consumption mode. The clock source can be selected
from the main clock, the sub clock, the built-in high-speed CR
clock or the built-in low-speed CR clock.
Interval timer: up to 64 s (sub clock: 32.768 kHz)
External Interrupt Controller Unit
AES Calculator
AES (Advanced Encryption Standard) calculator is an AES
common key crypto accelerator that is compliant with FIPS
(Federal Information Processing Standard Publication) 197.
Available key length: 128/192/256-bit
CBC mode and ECB mode support
Up to 24 external interrupt input pins
Clock and Reset
Non-maskable interrupt (NMI) input pin: 1
Clocks
Watchdog Timer (2 Channels)
The watchdog timer generates an interrupt or a reset when the
counter reaches a time-out value.
This series consists of two different watchdogs, hardware
watchdog and software watchdog.
The hardware watchdog timer is clocked by the built-in
low-speed CR oscillator. Therefore, the hardware watchdog is
active in any low-power consumption modes except RTC, Stop,
Deep standby RTC and Deep standby Stop mode.
CRC (Cyclic Redundancy Check) Accelerator
The CRC accelerator calculates the CRC which has a heavy
software processing load, and achieves a reduction of the
integrity check processing load for reception data and storage.
CCITT CRC16 and IEEE-802.3 CRC32 are supported.
CCITT
CRC16 Generator Polynomial: 0x1021
IEEE-802.3 CRC32 Generator Polynomial: 0x04C11DB7
HDMI-CEC/Remote Control Receiver (Up to 2
Channels)
HDMI-CEC transmitter
Header
block automatic transmission by judging Signal
free
Generating status interrupt by detecting Arbitration lost
Generating START, EOM, ACK automatically to output
CEC transmission by setting 1 byte data
Generating transmission status interrupt when transmitting
1 block (1 byte data and EOM/ACK)
HDMI-CEC receiver
Automatic
ACK reply function available
Line error detection function available
Remote control receiver
4
bytes reception buffer
Repeat code detection function available
A clock can be selected from five clock sources (two external
oscillators, two built-in CR oscillator, and main PLL).
Main clock: 4 MHz to 40 MHz
Sub clock: 32.768 kHz
Built-in high-speed CR clock: 4 MHz
Built-in low-speed CR clock : 100 kHz
Main PLL clock
Resets
Reset
request from the INITX pin
on reset
Software reset
Watchdog timer reset
Low-voltage detection reset
Clock supervisor reset
Power
Clock Supervisor (CSV)
The Clock Supervisor monitors the failure of external clocks
with a clock generated by a built-in CR oscillator.
If an external clock failure (clock stop) is detected, a reset is
asserted.
If an external frequency anomaly is detected, an interrupt or
a reset is asserted.
Low-Voltage Detector (LVD)
This series monitors the voltage on the VCC pin with a 2-stage
mechanism. When the voltage falls below a designated voltage,
the Low-voltage Detector generates an interrupt or a reset.
LVDR: monitor Vcc and auto-reset operation
LVD1: monitor Vcc and error reporting via an interrupt
LVD2: selectable to monitor Vcc or LVDI and error reporting
via an interrupt
Low Power Consumption Mode
This series has six low power consumption modes.
Sleep
Smart Card Interface (Max 2 Channels)
Timer
Compliant with ISO7816-3 specification
RTC
Card Reader only/B class card only
Stop
Available protocols
Deep standby RTC (selectable between keeping the value of
Transmitter:
8E2, 8O2, 8N2
Receiver: 8E1, 8O1, 8N2, 8N1, 9N1
Inverse mode
RAM and not)
Deep standby Stop (selectable between keeping the value of
RAM and not)
TX/RX FIFO integrated (RX: 16-bytes, TX:16-bytes)
Document Number: 001-99223 Rev.*A
Page 3 of 129
S6E1B8 Series
Peripheral Clock Gating
The system can reduce the current consumption of the total
system with gating the operation clocks of peripheral functions
not used.
VBAT
The consumption power during the RTC operation can be
reduced by supplying the power supply independent VBAT pin.
RTC (calendar circuit) / 32 kHz oscillation circuit. The following
circuit can also be used.
Power Supply
Wide voltage range:
VCC = 1.65V to 3.6 V
VCC = 3.0V to 3.6V (when USB is used)
VCC = 2.2V to 3.6V (when LCDC is used)
Power supply for VBAT: VBAT = 1.65 V to 3.6 V
RTC
32 kHz oscillation circuit
Power-on circuit
Back up register: 32 bytes
Port circuit
Debug
Serial Wire Debug Port (SW-DP)
Micro Trace Buffer (MTB)
Unique ID
A 41-bit unique value of the device has been set.
Document Number: 001-99223 Rev.*A
Page 4 of 129
S6E1B8 Series
Table of Contents
Features................................................................................................................................................................................... 1
1.
Product Lineup ............................................................................................................................................................... 7
2.
Packages......................................................................................................................................................................... 8
3.
Pin Assignment .............................................................................................................................................................. 9
4.
List of Pin Functions .................................................................................................................................................... 12
5.
I/O Circuit Type ............................................................................................................................................................. 36
6.
Handling Precautions .................................................................................................................................................. 46
6.1
Precautions for Product Design ................................................................................................................................... 46
6.2
Precautions for Package Mounting .............................................................................................................................. 47
6.3
Precautions for Use Environment ................................................................................................................................ 49
7.
Handling Devices ......................................................................................................................................................... 50
8.
Block Diagram .............................................................................................................................................................. 53
9.
Memory Map ................................................................................................................................................................. 54
10. Pin Status in Each CPU State ...................................................................................................................................... 57
11. Electrical Characteristics ............................................................................................................................................ 67
11.1 Absolute Maximum Ratings ......................................................................................................................................... 67
11.2 Recommended Operating Conditions.......................................................................................................................... 68
11.3 DC Characteristics....................................................................................................................................................... 69
11.3.1 Current Rating .............................................................................................................................................................. 69
11.3.2 Pin Characteristics ....................................................................................................................................................... 75
11.3.3 LCD Characteristic ....................................................................................................................................................... 76
11.4 AC Characteristics ....................................................................................................................................................... 80
11.4.1 Main Clock Input Characteristics .................................................................................................................................. 80
11.4.2 Sub Clock Input Characteristics ................................................................................................................................... 81
11.4.3 Built-in CR Oscillation Characteristics .......................................................................................................................... 82
11.4.4 Operating Conditions of Main PLL (In the Case of Using the Main Clock as the Input Clock of the PLL) .................... 83
11.4.5 Operating Conditions of Main PLL (In the Case of Using the Built-in High-Speed CR Clock as the
Input Clock of the Main PLL) ........................................................................................................................................ 83
11.4.6 Reset Input Characteristics .......................................................................................................................................... 84
11.4.7 Power-on Reset Timing................................................................................................................................................ 84
11.4.8 Base Timer Input Timing .............................................................................................................................................. 85
11.4.9 CSIO/SPI/UART Timing ............................................................................................................................................... 86
11.4.10 External Input Timing .............................................................................................................................................. 103
2
11.4.11 I C Timing ............................................................................................................................................................... 104
2
11.4.12 I S Timing ............................................................................................................................................................... 105
11.4.13 Smart Card Interface Characteristics ...................................................................................................................... 106
11.4.14 SW-DP Timing ........................................................................................................................................................ 107
11.5 12-bit A/D Converter .................................................................................................................................................. 108
11.6 USB Characteristics .................................................................................................................................................. 111
11.7 Low-Voltage Detection Characteristics ...................................................................................................................... 116
11.7.1 Low-Voltage Detection Reset ..................................................................................................................................... 116
11.7.2 Low-Voltage Detection Interrupt ................................................................................................................................. 117
11.7.3 Low-Voltage Detection Interrupt 2 .............................................................................................................................. 118
11.8 Flash Memory Write/Erase Characteristics ............................................................................................................... 119
11.9 Return Time from Low-Power Consumption Mode .................................................................................................... 120
11.9.1 Return Factor: Interrupt/WKUP .................................................................................................................................. 120
11.9.2 Return Factor: Reset .................................................................................................................................................. 122
12. Ordering Information ................................................................................................................................................. 124
Document Number: 001-99223 Rev.*A
Page 5 of 129
S6E1B8 Series
13. Package Dimensions ................................................................................................................................................. 125
Document History ............................................................................................................................................................... 128
Sales, Solutions, and Legal Information........................................................................................................................... 129
Document Number: 001-99223 Rev.*A
Page 6 of 129
S6E1B8 Series
1. Product Lineup
Memory Size
Product Name
Upper Bank
On-chip Flash memory
Lower Bank
On-chip SRAM
Function
S6E1B84E/F/G
256 Kbytes
48 Kbytes
32 Kbytes
S6E1B84E0A
S6E1B86E0A
S6E1B84EHA
S6E1B86EHA
80
Product Name
Pin count
S6E1B84F0A
S6E1B86F0A
S6E1B84FHA
S6E1B86FHA
100
Cortex-M0+
40.8 MHz
1.65 V to 3.6 V
1 unit
64ch
8ch (Max) with 128 bytes FIFO
2
I S: ch.5, ch.6
CPU
Frequency
Power supply voltage range
USB 2.0 (Device/Host)
DSTC
Multi-function Serial Interface
2
2
(UART/CSIO (SPI)/I C/I S)
Base Timer
(PWC/Reload timer/PWM/PPG)
20SEG x 8COM(Max) /
24SEG x 4COM(Max)
Multi-function
Timer
32SEG x 8COM(Max) /
36SEG x 4COM(Max)
40SEG x 8COM(Max) /
44SEG x 4COM(Max)
6ch
4ch
3ch
6ch
3ch
3ch
1 unit
Dual Timer
1 unit
HDMI-CEC/ Remote Control Receiver
Smart Card Interface
Real-time Clock
Watch Counter
CRC Accelerator
Watchdog timer
External Interrupt
I/O port
12-bit A/D converter
CSV (Clock Supervisor)
LVD (Low-voltage Detection)
High-speed
Built-in CR
Low-speed
Debug Function
Unique ID
AES Calculator
S6E1B84G0A
S6E1B86G0A
S6E1B84GHA
S6E1B86GHA
120
8ch (Max)
LCD controller
A/D activation
compare
Input capture
Free-run timer
Output compare
Waveform generator
PPG
S6E1B86E/F/G
512 Kbytes
48 Kbytes
64 Kbytes
2ch (max)
65 pins (Max)
16ch (1 unit)
-
Yes
*1
2ch (max)
1 unit (with battery power)
1 unit
Yes
1ch (SW) + 1ch (HW)
24 pins (Max), NMI × 1
82 pins (Max)
23ch (1 unit)
Yes
2ch
4 MHz
100 kHz
SW-DP
Yes
*1
Yes
102 pins (Max)
24ch (1 unit)
-
Yes
*1
*1: AES Calculator is built in following products.
S6E1B86GHA, S6E1B84GHA, S6E1B86FHA, S6E1B84FHA, S6E1B86EHA, S6E1B84EHA
Note:
−
All signals of the peripheral function in each product cannot be allocated by limiting the pins of package. It is necessary to use
the port relocate function of the I/O port according to your function use.
See "11 Electrical Characteristics 11.4 AC Characteristics 11.4.3 Built-in CR Oscillation Characteristics" for accuracy of built-in
CR.
Document Number: 001-99223 Rev.*A
Page 7 of 129
S6E1B8 Series
2. Packages
Product Name
Package
LQFP: LQH080-02
(0.50 mm pitch)
LQFP: LQI100
(0.50 mm pitch)
LQFP: LQM120
(0.50 mm pitch)
: Available
S6E1B84E/S6E1B86E
S6E1B84F/S6E1B86F
S6E1B84G/S6E1B86G
-
-
-
-
-
-
Note:
See "13. Package Dimensions" for detailed information on each package.
−
Document Number: 001-99223 Rev.*A
Page 8 of 129
S6E1B8 Series
3. Pin Assignment
LQH080-02
VSS
P82/SCK7_2
P81/SOT7_2/INT11_0/C1
P80/SIN7_2/INT20_1/C0
P60/SIN5_0/MI2SDI5_0/TIOA2_2/INT15_1/WKUP3/CEC1_0/IGTRG0_1
P61/SOT5_0/MI2SDO5_0/TIOB2_2/DTTI0X_2/SEG00
P62/SCK5_0/MI2SCK5_0/ADTG_3/INT07_1/SEG01/TIOA6_1/IC0_RST_0
P63/MI2SWS5_0/INT03_0/SEG02/TIOB6_1/IC0_DATA_0
P0F/NMIX/CROUT_1/RTCCO_0/SUBOUT_0/MI2SMCK5_0/WKUP0/IC0_CLK_0/SCK4_0
P0E/CTS4_0/TIOB3_2/INT21_0/SEG03/IC0_VCC_0
P0D/RTS4_0/TIOA3_2/INT20_0/SEG04/IC0_VPEN_0
P0C/INT19_0/UDP0
P0B/INT18_0/UDM0
P0A/SIN4_0/INT00_2/WKUP5/IC0_CIN_0/UHCONX0
P07/AN22/ADTG_0/SCK4_2/INT23_1/SEG07/SOT4_0
P04/SCK3_2/INT06_2
P03/SWDIO
P02/SIN3_2/TIOB5_0
P01/SWCLK
P00/SOT3_2/INT14_1
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
(TOP VIEW)
VCC
1
60 P21/AN18/SIN0_0/INT06_1/WKUP2/SEG11
P50/INT00_0/SIN3_1/VV4
2
59 P22/AN17/SOT0_0/TIOB7_1/SEG12
P51/INT01_0/SOT3_1/VV3
3
58 P23/AN16/SCK0_0/TIOA7_1/RTO00_1/SEG13
P52/INT02_0/SCK3_1/VV2
4
57 P1B/AN11/SOT4_1/IC02_1/INT20_2/SEG16
P53/SIN6_0/TIOA1_2/INT07_2/VV1
5
56 P1A/AN10/SIN4_1/IC01_1/INT05_1/SEG17
P54/SOT6_0/TIOB1_2/INT18_1/VV0
6
P55/SCK6_0/ADTG_1/INT19_1/SEG39
7
55 P19/AN09/SCK2_2/IC00_1/SEG18
54 P18/AN08/SOT2_2/SEG19
`
P56/INT08_2/MI2SMCK6_1/SEG38/WKUP9/CEC1_1
8
P30/TIOB0_1/SCS60_1/INT03_2/MI2SWS6_1/COM7/SEG43/WKUP4
9
53 AVRH
52 AVRL
P31/TIOB1_1/SCK6_1/MI2SCK6_1/INT04_2/COM6/SEG42 10
51 AVSS
LQFP - 80
P32/TIOB2_1/SOT6_1/MI2SDO6_1/INT05_2/COM5/SEG41 11
50 AVCC
P33/INT04_0/TIOB3_1/SIN6_1/MI2SDI6_1/ADTG_6/COM4/SEG40 12
49 P17/AN07/SIN2_2/INT04_1/SEG20
P39/DTTI0X_0/ADTG_2/TIOB4_0/INT06_0/COM3 13
48 P16/AN06/SCK0_1/INT15_0/SEG21
P3A/RTO00_0/TIOA0_1/INT07_0/RTCCO_2/SUBOUT_2/IC1_CIN_0/COM2 14
47 P15/AN05/IC1_CIN_1/SOT0_1/IC03_2/INT14_0/SEG22
P3B/RTO01_0/TIOA1_1/IC1_DATA_0/COM1 15
46 P14/AN04/IC1_DATA_1/RTS1_1/SIN0_1/INT03_1/IC02_2/SEG23
P3C/RTO02_0/TIOA2_1/INT18_2/IC1_RST_0/COM0 16
45 P13/AN03/IC1_RST_1/SCK1_1/RTCCO_1/IC01_2/SUBOUT_1/SEG24
P3D/RTO03_0/TIOA3_1/IC1_VPEN_0/SEG36 17
44 P12/AN02/IC1_VPEN_1/SOT1_1/IC00_2/SEG25
P3E/RTO04_0/TIOA4_1/INT19_2/IC1_VCC_0/SEG35/WKUP8 18
43 P11/AN01/IC1_VCC_1/SIN1_1/INT02_1/FRCK0_2/WKUP1/SEG26
P3F/RTO05_0/TIOA5_1/IC1_CLK_0/SEG34 19
42 P10/AN00/IC1_CLK_1/CTS1_1/SEG27
40
VSS
PE3/X1 39
PE2/X0 38
37
MD0
PE0/MD1 36
P4D/TIOB3_0/INT13_0/SCK7_1/WKUP6/SEG28 35
31
VBAT
P4C/TIOB2_0/SOT7_1/INT12_0/SEG29/CEC0_0 34
30
P49/VWAKEUP
P4B/TIOB1_0/SIN7_1/INT22_1/WKUP7/SEG30/IGTRG0_0 33
29
P48/VREGCTL
P4A/TIOB0_0/SCS70_1/INT21_1/SEG31 32
28
P47/X1A
25
VCC
27
24
VSS
P46/X0A
23
C
INITX 26
22
P45/LVDI/TIOA5_0/SEG32/IC0_CIN_1
41 VCC
P44/TIOA4_0/INT10_0/SEG33/RTS1_2/IC0_DATA_1 21
VSS 20
Note:
−
The number after the underscore ("_") in a pin name such as XXX_1 and XXX_2 indicates the relocated port number. The
channel on such pin has multiple functions, each of which has its own pin name. Use the Extended Port Function Register
(EPFR) to select the pin to be used.
Document Number: 001-99223 Rev.*A
Page 9 of 129
S6E1B8 Series
LQI100
P82/SCK7_2
P81/SOT7_2/INT11_0/C1
P80/SIN7_2/INT20_1/C0
P60/SIN5_0/MI2SDI5_0/TIOA2_2/INT15_1/WKUP3/CEC1_0/IGTRG0_1
P61/SOT5_0/MI2SDO5_0/TIOB2_2/DTTI0X_2/SEG00
P62/SCK5_0/MI2SCK5_0/ADTG_3/INT07_1/SEG01/TIOA6_1/IC0_RST_0
P63/MI2SWS5_0/INT03_0/SEG02/TIOB6_1/IC0_DATA_0
P0F/NMIX/CROUT_1/RTCCO_0/SUBOUT_0/MI2SMCK5_0/WKUP0/IC0_CLK_0/SCK4_0
P0E/CTS4_0/TIOB3_2/INT21_0/SEG03/IC0_VCC_0
P0D/RTS4_0/TIOA3_2/INT20_0/SEG04/IC0_VPEN_0
P0C/INT19_0/UDP0
P0B/INT18_0/UDM0
P0A/SIN4_0/INT00_2/WKUP5/IC0_CIN_0/UHCONX0
P09/TIOB0_2/RTS4_2/INT17_0/SEG05
P08/AN23/TIOA0_2/CTS4_2/INT16_0/SEG06
P07/AN22/ADTG_0/SCK4_2/INT23_1/SEG07/SOT4_0
P06/AN21/TIOB5_2/SOT4_2/INT01_1/SEG08
P05/AN20/TIOA5_2/SIN4_2/INT00_1/SEG09/WKUP10
P04/SCK3_2/INT06_2
P03/SWDIO
P02/SIN3_2/TIOB5_0
P01/SWCLK
P00/SOT3_2/INT14_1
VCC
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
100 VSS
(TOP VIEW)
VCC
1
75 VSS
P50/INT00_0/SIN3_1/VV4
2
74 P20/AN19/INT05_0/CROUT_0/SEG10
P51/INT01_0/SOT3_1/VV3
3
73 P21/AN18/SIN0_0/INT06_1/WKUP2/SEG11
P52/INT02_0/SCK3_1/VV2
4
72 P22/AN17/SOT0_0/TIOB7_1/SEG12
P53/SIN6_0/TIOA1_2/INT07_2/VV1
5
71 P23/AN16/SCK0_0/TIOA7_1/RTO00_1/SEG13
P54/SOT6_0/TIOB1_2/INT18_1/VV0
6
70 P1E/AN14/RTS4_1/ADTG_5/FRCK0_1/INT23_2
P55/SCK6_0/ADTG_1/INT19_1/SEG39
7
69 P1D/AN13/CTS4_1/DTTI0X_1/INT22_2/SEG14
P56/INT08_2/MI2SMCK6_1/SEG38/WKUP9/CEC1_1
8
68 P1C/AN12/SCK4_1/IC03_1/INT21_2/SEG15
P30/TIOB0_1/SCS60_1/INT03_2/MI2SWS6_1/COM7/SEG43/WKUP4
9
67 P1B/AN11/SOT4_1/IC02_1/INT20_2/SEG16
P31/TIOB1_1/SCK6_1/MI2SCK6_1/INT04_2/COM6/SEG42 10
66 P1A/AN10/SIN4_1/IC01_1/INT05_1/SEG17
P32/TIOB2_1/SOT6_1/MI2SDO6_1/INT05_2/COM5/SEG41 11
65 P19/AN09/SCK2_2/IC00_1/SEG18
64 P18/AN08/SOT2_2/SEG19
P33/INT04_0/TIOB3_1/SIN6_1/MI2SDI6_1/ADTG_6/COM4/SEG40 12
63 AVRH
P34/SCS61_1/FRCK0_0/TIOB4_1 13
LQFP - 100
P35/SCS62_1/IC03_0/TIOB5_1/INT08_1/SEG37 14
62 AVRL
P36/IC02_0/SIN5_2/INT09_1/WKUP11 15
61 AVSS
P37/IC01_0/SOT5_2/INT10_1 16
60 AVCC
P38/IC00_0/SCK5_2/INT11_1 17
59 P17/AN07/SIN2_2/INT04_1/SEG20
58 P16/AN06/SCK0_1/INT15_0/SEG21
P39/DTTI0X_0/ADTG_2/TIOB4_0/INT06_0/COM3 18
57 P15/AN05/IC1_CIN_1/SOT0_1/IC03_2/INT14_0/SEG22
P3A/RTO00_0/TIOA0_1/INT07_0/RTCCO_2/SUBOUT_2/IC1_CIN_0/COM2 19
56 P14/AN04/IC1_DATA_1/RTS1_1/SIN0_1/INT03_1/IC02_2/SEG23
P3B/RTO01_0/TIOA1_1/IC1_DATA_0/COM1 20
55 P13/AN03/IC1_RST_1/SCK1_1/RTCCO_1/IC01_2/SUBOUT_1/SEG24
P3C/RTO02_0/TIOA2_1/INT18_2/IC1_RST_0/COM0 21
P3D/RTO03_0/TIOA3_1/IC1_VPEN_0/SEG36 22
54 P12/AN02/IC1_VPEN_1/SOT1_1/IC00_2/SEG25
53 P11/AN01/IC1_VCC_1/SIN1_1/INT02_1/FRCK0_2/WKUP1/SEG26
P3E/RTO04_0/TIOA4_1/INT19_2/IC1_VCC_0/SEG35/WKUP8 23
52 P10/AN00/IC1_CLK_1/CTS1_1/SEG27
P3F/RTO05_0/TIOA5_1/IC1_CLK_0/SEG34 24
50
VSS
PE3/X1 49
PE2/X0 48
47
MD0
PE0/MD1 46
P4D/TIOB3_0/INT13_0/SCK7_1/WKUP6/SEG28 45
41
VBAT
P4C/TIOB2_0/SOT7_1/INT12_0/SEG29/CEC0_0 44
40
P49/VWAKEUP
P4B/TIOB1_0/SIN7_1/INT22_1/WKUP7/SEG30/IGTRG0_0 43
39
P48/VREGCTL
P4A/TIOB0_0/SCS70_1/INT21_1/SEG31 42
38
P47/X1A
35
VCC
37
34
VSS
P46/X0A
33
C
INITX 36
32
P45/LVDI/TIOA5_0/SEG32/IC0_CIN_1
P44/TIOA4_0/INT10_0/SEG33/RTS1_2/IC0_DATA_1 31
29
P42/TIOA2_0/INT08_0/SCK1_2/IC0_VPEN_1
P43/TIOA3_0/INT09_0/ADTG_7/CTS1_2/IC0_RST_1 30
28
P41/TIOA1_0/INT13_1/SOT1_2/IC0_VCC_1
VCC
26
51 VCC
P40/TIOA0_0/INT12_1/SIN1_2/IC0_CLK_1 27
VSS 25
Note:
−
The number after the underscore ("_") in a pin name such as XXX_1 and XXX_2 indicates the relocated port number. The
channel on such pin has multiple functions, each of which has its own pin name. Use the Extended Port Function Register
(EPFR) to select the pin to be used.
Document Number: 001-99223 Rev.*A
Page 10 of 129
S6E1B8 Series
LQM120
VSS
P82/SCK7_2
P81/SOT7_2/INT11_0/C1
P80/SIN7_2/INT20_1/C0
P60/SIN5_0/MI2SDI5_0/TIOA2_2/INT15_1/WKUP3/CEC1_0/IGTRG0_1
P61/SOT5_0/MI2SDO5_0/TIOB2_2/DTTI0X_2/SEG00
P62/SCK5_0/MI2SCK5_0/ADTG_3/INT07_1/SEG01/TIOA6_1/IC0_RST_0
P63/SIN5_1/MI2SWS5_0/INT03_0/SEG02/TIOB6_1/IC0_DATA_0
P64/SOT5_1/TIOA7_0/INT10_2
P65/SCK5_1/TIOB7_0/INT23_0
P66/SIN3_0/INT11_2
P67/SOT3_0/TIOA7_2/INT22_0
P68/SCK3_0/TIOB7_2/INT12_2
P0F/NMIX/CROUT_1/RTCCO_0/SUBOUT_0/MI2SMCK5_0/WKUP0/IC0_CLK_0/SCK4_0
P0E/CTS4_0/TIOB3_2/INT21_0/SEG03/IC0_VCC_0
P0D/RTS4_0/TIOA3_2/INT20_0/SEG04/IC0_VPEN_0
P0C/INT19_0/UDP0
P0B/INT18_0/UDM0
P0A/SIN4_0/INT00_2/WKUP5/IC0_CIN_0/UHCONX0
P09/TIOB0_2/RTS4_2/INT17_0/SEG05
P08/AN23/TIOA0_2/CTS4_2/INT16_0/SEG06
P07/AN22/ADTG_0/SCK4_2/INT23_1/SEG07/SOT4_0
P06/AN21/TIOB5_2/SOT4_2/INT01_1/SEG08
P05/AN20/TIOA5_2/SIN4_2/INT00_1/SEG09/WKUP10
P04/SCK3_2/INT06_2
P03/SWDIO
P02/SIN3_2/TIOB5_0
P01/SWCLK
P00/SOT3_2/INT14_1
VCC
120
119
118
117
116
115
114
113
112
111
110
109
108
107
106
105
104
103
102
101
100
99
98
97
96
95
94
93
92
91
(TOP VIEW)
VCC
1
90 VSS
P50/INT00_0/SIN3_1/VV4
2
89 P20/AN19/INT05_0/CROUT_0/SEG10
P51/INT01_0/SOT3_1/VV3
3
88 P21/AN18/SIN0_0/INT06_1/WKUP2/SEG11
P52/INT02_0/SCK3_1/VV2
4
87 P22/AN17/SOT0_0/TIOB7_1/SEG12
P53/SIN6_0/TIOA1_2/INT07_2/VV1
5
86 P23/AN16/SCK0_0/TIOA7_1/RTO00_1/SEG13
P54/SOT6_0/TIOB1_2/INT18_1/VV0
6
85 P24/SIN2_1/RTO01_1/INT17_1
P55/SCK6_0/ADTG_1/INT19_1/SEG39
7
84 P25/SOT2_1/RTO02_1
P56/SIN1_0/INT08_2/MI2SMCK6_1/SEG38/WKUP9/CEC1_1
8
83 P26/SCK2_1/RTO03_1
P57/SOT1_0
9
82 P27/AN15/RTO04_1/TIOA6_2/INT02_2
P58/SCK1_0 10
81 P28/ADTG_4/RTO05_1/TIOB6_2
P59/SIN7_0/INT16_1 11
80 P1E/AN14/RTS4_1/ADTG_5/FRCK0_1/INT23_2
P5A/SOT7_0/INT16_2 12
79 P1D/AN13/CTS4_1/DTTI0X_1/INT22_2/SEG14
P5B/SCK7_0/INT17_2 13
78 P1C/AN12/SCK4_1/IC03_1/INT21_2/SEG15
P30/TIOB0_1/SCS60_1/INT03_2/MI2SWS6_1/COM7/SEG43/WKUP4 14
77 P1B/AN11/SOT4_1/IC02_1/INT20_2/SEG16
LQFP - 120
P31/TIOB1_1/SCK6_1/MI2SCK6_1/INT04_2/COM6/SEG42 15
P32/TIOB2_1/SOT6_1/MI2SDO6_1/INT05_2/COM5/SEG41 16
76 P1A/AN10/SIN4_1/IC01_1/INT05_1/SEG17
75 P19/AN09/SCK2_2/IC00_1/SEG18
P33/INT04_0/TIOB3_1/SIN6_1/MI2SDI6_1/ADTG_6/COM4/SEG40 17
74 P18/AN08/SOT2_2/SEG19
P34/SCS61_1/FRCK0_0/TIOB4_1 18
73 AVRH
P35/SCS62_1/IC03_0/TIOB5_1/INT08_1/SEG37 19
72 AVRL
P36/IC02_0/SIN5_2/INT09_1/WKUP11 20
71 AVSS
P37/IC01_0/SOT5_2/INT10_1 21
70 AVCC
P38/IC00_0/SCK5_2/INT11_1 22
69 P17/AN07/SIN2_2/INT04_1/SEG20
P39/DTTI0X_0/ADTG_2/TIOB4_0/INT06_0/COM3 23
68 P16/AN06/SCK0_1/INT15_0/SEG21
P3A/RTO00_0/TIOA0_1/INT07_0/RTCCO_2/SUBOUT_2/IC1_CIN_0/COM2 24
67 P15/AN05/IC1_CIN_1/SOT0_1/IC03_2/INT14_0/SEG22
P3B/RTO01_0/TIOA1_1/IC1_DATA_0/COM1 25
66 P14/AN04/IC1_DATA_1/RTS1_1/SIN0_1/INT03_1/IC02_2/SEG23
P3C/RTO02_0/TIOA2_1/INT18_2/IC1_RST_0/COM0 26
65 P13/AN03/IC1_RST_1/SCK1_1/RTCCO_1/IC01_2/SUBOUT_1/SEG24
P3D/RTO03_0/TIOA3_1/IC1_VPEN_0/SEG36 27
64 P12/AN02/IC1_VPEN_1/SOT1_1/IC00_2/SEG25
P3E/RTO04_0/TIOA4_1/INT19_2/IC1_VCC_0/SEG35/WKUP8 28
63 P11/AN01/IC1_VCC_1/SIN1_1/INT02_1/FRCK0_2/WKUP1/SEG26
P3F/RTO05_0/TIOA5_1/IC1_CLK_0/SEG34 29
62 P10/AN00/IC1_CLK_1/CTS1_1/SEG27
60
VSS
PE3/X1 59
PE2/X0 58
57
MD0
PE0/MD1 56
46
VBAT
P74/SCK2_0 55
45
P49/VWAKEUP
P73/SOT2_0/TIOB6_0/INT15_2 54
44
P48/VREGCTL
P72/SIN2_0/TIOA6_0/INT14_2 53
43
P71/SCS72_1/TIOB4_2/INT13_2 52
42
P47/X1A
P70/SCS71_1/TIOA4_2 51
41
INITX
P46/X0A
P4D/TIOB3_0/INT13_0/SCK7_1/WKUP6/SEG28 50
40
VCC
P4C/TIOB2_0/SOT7_1/INT12_0/SEG29/CEC0_0 49
39
VSS
P4B/TIOB1_0/SIN7_1/INT22_1/WKUP7/SEG30/IGTRG0_0 48
38
C
P4A/TIOB0_0/SCS70_1/INT21_1/SEG31 47
37
P45/LVDI/TIOA5_0/SEG32/IC0_CIN_1
P44/TIOA4_0/INT10_0/SEG33/RTS1_2/IC0_DATA_1 36
34
P43/TIOA3_0/INT09_0/ADTG_7/CTS1_2/IC0_RST_1 35
33
P41/TIOA1_0/INT13_1/SOT1_2/IC0_VCC_1
P42/TIOA2_0/INT08_0/SCK1_2/IC0_VPEN_1
VCC
31
61 VCC
P40/TIOA0_0/INT12_1/SIN1_2/IC0_CLK_1 32
VSS 30
Note:
−
The number after the underscore ("_") in a pin name such as XXX_1 and XXX_2 indicates the relocated port number. The
channel on such pin has multiple functions, each of which has its own pin name. Use the Extended Port Function Register
(EPFR) to select the pin to be used.
Document Number: 001-99223 Rev.*A
Page 11 of 129
S6E1B8 Series
4. List of Pin Functions
List of Pin Numbers
The number after the underscore ("_") in a pin name such as XXX_1 and XXX_2 indicates the relocated port number. The channel
on such pin has multiple functions, each of which has its own pin name. Use the Extended Port Function Register (EPFR) to select
the pin to be used.
Pin No.
LQFP-120
LQFP-100
LQFP-80
1
1
1
Pin Name
I/O Circuit Type
VCC
Pin State Type
-
P50
2
2
2
SIN3_1
INT00_0
Q
X
Q
X
Q
X
Q
X
Q
X
L
S
L
U
F
I
F
I
F
J
VV4
3
3
3
4
4
4
5
5
5
6
6
6
7
7
7
8
8
-
-
9
-
-
10
-
-
11
-
-
8
Document Number: 001-99223 Rev.*A
P51
SOT3_1
INT01_0
VV3
P52
SCK3_1
INT02_0
VV2
P53
SIN6_0
TIOA1_2
INT07_2
VV1
P54
SOT6_0
TIOB1_2
INT18_1
VV0
P55
SCK6_0
ADTG_1
INT19_1
SEG39
P56
MI2SMCK6_1
CEC1_1
INT08_2
WKUP9
SEG38
SIN1_0
P57
SOT1_0
P58
SCK1_0
P59
SIN7_0
INT16_1
Page 12 of 129
S6E1B8 Series
Pin No.
LQFP-120
LQFP-100
LQFP-80
12
-
-
13
-
-
14
9
9
15
10
10
16
11
11
17
12
12
18
13
-
19
14
-
20
15
-
21
16
-
Document Number: 001-99223 Rev.*A
Pin Name
P5A
SOT7_0
INT16_2
P5B
SCK7_0
INT17_2
P30
TIOB0_1
SCS60_1
MI2SWS6_1
INT03_2
WKUP4
COM7
SEG43
P31
TIOB1_1
SCK6_1
MI2SCK6_1
INT04_2
COM6
SEG42
P32
TIOB2_1
SOT6_1
MI2SDO6_1
INT05_2
COM5
SEG41
P33
TIOB3_1
SIN6_1
MI2SDI6_1
INT04_0
ADTG_6
COM4
SEG40
P34
SCS61_1
FRCK0_0
TIOB4_1
P35
SCS62_1
IC03_0
TIOB5_1
INT08_1
SEG37
P36
IC02_0
SIN5_2
INT09_1
WKUP11
P37
IC01_0
SOT5_2
INT10_1
I/O Circuit Type
Pin State Type
F
J
F
J
M
T
M
S
M
S
M
S
I
I
L
S
I
N
I
J
Page 13 of 129
S6E1B8 Series
Pin No.
LQFP-120
LQFP-100
LQFP-80
22
17
-
23
18
13
24
19
14
25
20
15
26
21
16
27
22
17
28
23
18
29
24
19
30
31
25
26
20
-
32
27
-
Document Number: 001-99223 Rev.*A
Pin Name
P38
IC00_0
SCK5_2
INT11_1
P39
DTTI0X_0
TIOB4_0
ADTG_2
INT06_0
COM3
P3A
RTO00_0
TIOA0_1
RTCCO_2
SUBOUT_2
IC1_CIN_0
INT07_0
COM2
P3B
RTO01_0
TIOA1_1
IC1_DATA_0
COM1
P3C
RTO02_0
TIOA2_1
INT18_2
IC1_RST_0
COM0
P3D
RTO03_0
TIOA3_1
IC1_VPEN_0
SEG36
P3E
RTO04_0
TIOA4_1
IC1_VCC_0
INT19_2
WKUP8
SEG35
P3F
RTO05_0
TIOA5_1
IC1_CLK_0
SEG34
VSS
VCC
P40
TIOA0_0
IC0_CLK_1
INT12_1
SIN1_2
I/O Circuit Type
Pin State Type
F
J
N
S
N
S
N
P
N
S
L
P
L
T
L
P
-
-
F
J
Page 14 of 129
S6E1B8 Series
Pin No.
LQFP-120
LQFP-100
LQFP-80
33
28
-
34
29
-
35
30
-
36
31
21
37
32
22
38
39
40
41
33
34
35
36
23
24
25
26
42
37
27
43
38
28
44
39
29
45
40
30
46
41
31
47
42
32
48
43
33
Document Number: 001-99223 Rev.*A
Pin Name
P41
TIOA1_0
SOT1_2
IC0_VCC_1
INT13_1
P42
TIOA2_0
SCK1_2
IC0_VPEN_1
INT08_0
P43
TIOA3_0
CTS1_2
ADTG_7
IC0_RST_1
INT09_0
P44
TIOA4_0
IC0_DATA_1
INT10_0
RTS1_2
SEG33
P45
TIOA5_0
IC0_CIN_1
LVDI
SEG32
C
VSS
VCC
INITX
P46
X0A
P47
X1A
P48
VREGCTL
P49
VWAKEUP
VBAT
P4A
TIOB0_0
SCS70_1
INT21_1
SEG31
P4B
TIOB1_0
SIN7_1
INT22_1
WKUP7
SEG30
IGTRG0_0
I/O Circuit Type
Pin State Type
F
J
F
J
F
J
L
S
L
P
B
C
D
E
E
F
I
I
I
I
-
-
L
S
L
T
Page 15 of 129
S6E1B8 Series
Pin No.
LQFP-120
LQFP-100
LQFP-80
Pin Name
P4C
TIOB2_0
SOT7_1
CEC0_0
INT12_0
SEG29
P4D
TIOB3_0
SCK7_1
INT13_0
WKUP6
SEG28
P70
TIOA4_2
SCS71_1
P71
TIOB4_2
SCS72_1
INT13_2
P72
SIN2_0
TIOA6_0
INT14_2
P73
SOT2_0
TIOB6_0
INT15_2
P74
SCK2_0
PE0
MD1
MD0
PE2
X0
PE3
I/O Circuit Type
Pin State Type
L
R
L
T
F
I
F
J
F
J
F
J
F
I
C
D
J
M
A
A
A
B
49
44
34
50
45
35
51
-
-
52
-
-
53
-
-
54
-
-
55
-
-
56
46
36
57
47
37
58
48
38
59
49
39
60
50
40
VSS
-
-
61
51
41
VCC
-
-
P
K
P
W
62
52
42
63
53
43
Document Number: 001-99223 Rev.*A
X1
P10
IC1_CLK_1
CTS1_1
AN00
SEG27
P11
IC1_VCC_1
SIN1_1
FRCK0_2
INT02_1
WKUP1
AN01
SEG26
Page 16 of 129
S6E1B8 Series
Pin No.
LQFP-120
LQFP-100
LQFP-80
64
54
44
65
55
45
66
56
46
67
57
47
68
58
48
69
59
49
70
71
72
73
60
61
62
63
50
51
52
53
74
64
54
75
65
55
Document Number: 001-99223 Rev.*A
Pin Name
P12
IC1_VPEN_1
SOT1_1
IC00_2
AN02
SEG25
P13
IC1_RST_1
SCK1_1
RTCCO_1
IC01_2
SUBOUT_1
AN03
SEG24
P14
IC1_DATA_1
RTS1_1
SIN0_1
IC02_2
INT03_1
AN04
SEG23
P15
IC1_CIN_1
SOT0_1
IC03_2
INT14_0
AN05
SEG22
P16
SCK0_1
INT15_0
AN06
SEG21
P17
SIN2_2
INT04_1
AN07
SEG20
AVCC
AVSS
AVRL
AVRH
P18
SOT2_2
AN08
SEG19
P19
SCK2_2
IC00_1
AN09
SEG18
I/O Circuit Type
Pin State Type
P
K
P
K
P
V
P
V
P
V
P
V
-
-
P
K
P
K
Page 17 of 129
S6E1B8 Series
Pin No.
LQFP-120
LQFP-100
LQFP-80
76
66
56
77
67
57
78
68
-
79
69
-
80
70
-
81
-
-
82
-
-
83
-
-
84
-
-
85
-
-
86
71
58
Document Number: 001-99223 Rev.*A
Pin Name
P1A
SIN4_1
IC01_1
INT05_1
AN10
SEG17
P1B
SOT4_1
IC02_1
INT20_2
AN11
SEG16
P1C
SCK4_1
IC03_1
INT21_2
AN12
SEG15
P1D
CTS4_1
DTTI0X_1
INT22_2
AN13
SEG14
P1E
RTS4_1
FRCK0_1
ADTG_5
INT23_2
AN14
P28
RTO05_1
TIOB6_2
ADTG_4
P27
RTO04_1
TIOA6_2
INT02_2
AN15
P26
SCK2_1
RTO03_1
P25
SOT2_1
RTO02_1
P24
SIN2_1
RTO01_1
INT17_1
P23
SCK0_0
TIOA7_1
RTO00_1
AN16
SEG13
I/O Circuit Type
Pin State Type
P
V
P
V
P
V
P
V
H
L
F
I
G
L
F
I
F
I
F
J
P
K
Page 18 of 129
S6E1B8 Series
Pin No.
LQFP-120
LQFP-100
LQFP-80
87
72
59
88
73
60
89
74
-
90
91
75
76
-
92
77
61
93
78
62
94
79
63
95
80
64
96
81
65
97
82
-
98
83
-
99
84
66
Document Number: 001-99223 Rev.*A
Pin Name
P22
SOT0_0
TIOB7_1
AN17
SEG12
P21
SIN0_0
INT06_1
WKUP2
AN18
SEG11
P20
INT05_0
CROUT_0
AN19
SEG10
VSS
VCC
P00
SOT3_2
INT14_1
P01
SWCLK
P02
SIN3_2
TIOB5_0
P03
SWDIO
P04
SCK3_2
INT06_2
P05
TIOA5_2
SIN4_2
INT00_1
WKUP10
AN20
SEG09
P06
TIOB5_2
SOT4_2
INT01_1
AN21
SEG08
P07
SCK4_2
ADTG_0
INT23_1
AN22
SEG07
SOT4_0
I/O Circuit Type
Pin State Type
P
K
P
W
P
V
-
-
I
J
I
H
I
I
I
H
I
J
P
W
P
V
P
V
Page 19 of 129
S6E1B8 Series
Pin No.
LQFP-120
LQFP-100
LQFP-80
100
85
-
101
86
-
102
87
67
103
88
68
104
89
69
105
90
70
106
91
71
107
92
72
108
-
-
109
-
-
110
-
-
111
-
-
Document Number: 001-99223 Rev.*A
Pin Name
P08
TIOA0_2
CTS4_2
INT16_0
AN23
SEG06
P09
TIOB0_2
RTS4_2
INT17_0
SEG05
P0A
SIN4_0
INT00_2
WKUP5
IC0_CIN_0
UHCONX0
P0B
INT18_0
UDM0
P0C
INT19_0
UDP0
P0D
RTS4_0
TIOA3_2
INT20_0
SEG04
IC0_VPEN_0
P0E
CTS4_0
TIOB3_2
INT21_0
SEG03
IC0_VCC_0
P0F
CROUT_1
RTCCO_0
SUBOUT_0
MI2SMCK5_0
NMIX
WKUP0
IC0_CLK_0
SCK4_0
P68
SCK3_0
TIOB7_2
INT12_2
P67
SOT3_0
TIOA7_2
INT22_0
P66
SIN3_0
INT11_2
P65
I/O Circuit Type
Pin State Type
P
V
L
S
I
O
K
Q
K
Q
L
S
L
S
I
G
F
J
F
J
F
J
F
J
Page 20 of 129
S6E1B8 Series
Pin No.
LQFP-120
112
LQFP-100
LQFP-80
-
-
93
73
-
-
114
94
74
115
95
75
116
96
76
117
97
77
118
98
78
119
99
79
120
100
80
113
Pin Name
SCK5_1
TIOB7_0
INT23_0
P64
SOT5_1
TIOA7_0
INT10_2
P63
MI2SWS5_0
INT03_0
SEG02
TIOB6_1
IC0_DATA_0
SIN5_1
P62
SCK5_0
MI2SCK5_0
ADTG_3
INT07_1
SEG01
TIOA6_1
IC0_RST_0
P61
SOT5_0
MI2SDO5_0
TIOB2_2
DTTI0X_2
SEG00
P60
SIN5_0
MI2SDI5_0
TIOA2_2
CEC1_0
INT15_1
WKUP3
IGTRG0_1
P80
SIN7_2
INT20_1
C0
P81
SOT7_2
INT11_0
C1
P82
SCK7_2
VSS
I/O Circuit Type
Pin State Type
F
J
L
S
L
S
L
P
I
O
O
J
O
J
I
I
-
-
*: 5 V tolerant I/O
Document Number: 001-99223 Rev.*A
Page 21 of 129
S6E1B8 Series
List of Pin Functions
The number after the underscore ("_") in a pin name such as XXX_1 and XXX_2 indicates the relocated port number. The channel
on such pin has multiple functions, each of which has its own pin name. Use the Extended Port Function Register (EPFR) to select
the pin to be used.
Pin Function
LQFP-120
99
7
23
114
81
80
17
35
62
Pin No.
LQFP-100
84
7
18
94
70
12
30
52
LQFP-80
66
7
13
74
12
42
AN01
63
53
43
AN02
64
54
44
AN03
65
55
45
AN04
66
56
46
AN05
67
57
47
AN06
AN07
AN08
AN09
AN10
AN11
AN12
AN13
AN14
AN15
AN16
AN17
AN18
AN19
AN20
AN21
AN22
AN23
TIOA0_0
TIOA0_1
TIOA0_2
TIOB0_0
TIOB0_1
TIOB0_2
68
69
74
75
76
77
78
79
80
82
86
87
88
89
97
98
99
100
32
24
100
47
14
101
58
59
64
65
66
67
68
69
70
71
72
73
74
82
83
84
85
27
19
85
42
9
86
48
49
54
55
56
57
58
59
60
66
14
32
9
-
Pin Name
ADTG_0
ADTG_1
ADTG_2
ADTG_3
ADTG_4
ADTG_5
ADTG_6
ADTG_7
AN00
ADC
Base Timer 0
Document Number: 001-99223 Rev.*A
Function Description
A/D converter external trigger
input pin
A/D converter analog input pin.
ANxx describes ADC ch.xx.
Base timer ch.0 TIOA pin
Base timer ch.0 TIOB pin
Page 22 of 129
S6E1B8 Series
Pin Function
Base Timer 1
Pin Name
TIOA1_0
TIOA1_1
TIOA1_2
TIOB1_0
TIOB1_1
TIOB1_2
TIOA2_0
TIOA2_1
Base Timer 2
Base Timer 3
Base Timer 4
Base Timer 5
Base Timer 6
Base Timer 7
Debugger
Function Description
Base timer ch.1 TIOA pin
Base timer ch.1 TIOB pin
Base timer ch.2 TIOA pin
TIOA2_2
TIOB2_0
TIOB2_1
TIOB2_2
TIOA3_0
TIOA3_1
TIOA3_2
TIOB3_0
TIOB3_1
TIOB3_2
TIOA4_0
TIOA4_1
TIOA4_2
TIOB4_0
TIOB4_1
TIOB4_2
TIOA5_0
TIOA5_1
TIOA5_2
TIOB5_0
TIOB5_1
TIOB5_2
TIOA6_0
TIOA6_1
TIOA6_2
TIOB6_0
TIOB6_1
TIOB6_2
TIOA7_0
TIOA7_1
TIOA7_2
TIOB7_0
TIOB7_1
TIOB7_2
SWCLK
SWDIO
Document Number: 001-99223 Rev.*A
Base timer ch.2 TIOB pin
Base timer ch.3 TIOA pin
Base timer ch.3 TIOB pin
Base timer ch.4 TIOA pin
Base timer ch.4 TIOB pin
Base timer ch.5 TIOA pin
Base timer ch.5 TIOB pin
Base timer ch.6 TIOA pin
Base timer ch.6 TIOB pin
Base timer ch.7 TIOA pin
Base timer ch.7 TIOB pin
Serial wire debug interface clock input pin
Serial wire debug interface data
input / output pin
LQFP-120
33
25
5
48
15
6
34
Pin No.
LQFP-100
28
20
5
43
10
6
29
LQFP-80
15
5
33
10
6
-
26
21
16
116
96
76
49
16
115
35
27
105
50
17
106
36
28
51
23
18
52
37
29
97
94
19
98
53
114
82
54
113
81
112
86
109
111
87
108
93
44
11
95
30
22
90
45
12
91
31
23
18
13
32
24
82
79
14
83
94
93
71
72
78
34
11
75
17
70
35
12
71
21
18
13
22
19
63
74
73
58
59
62
95
80
64
Page 23 of 129
S6E1B8 Series
Pin Function
Pin Name
INT00_0
INT00_1
INT00_2
INT01_0
INT01_1
Function Description
External interrupt request 00 input pin
External interrupt request 01 input pin
INT02_0
Pin No.
LQFP-100
2
82
87
3
LQFP-80
2
67
3
98
83
-
4
4
4
63
53
43
INT02_2
82
-
-
INT03_0
113
93
73
66
56
46
14
9
9
17
69
15
89
76
16
23
88
96
24
114
5
34
19
8
35
20
36
21
112
118
22
110
49
32
108
50
33
52
67
92
53
12
59
10
74
66
11
18
73
81
19
94
5
29
14
8
30
15
31
16
98
17
44
27
45
28
57
77
-
12
49
10
56
11
13
60
65
14
74
5
8
21
78
34
35
47
61
-
INT02_1
INT03_1
External interrupt request 02 input pin
External interrupt request 03 input pin
INT03_2
External
Interrupt
LQFP-120
2
97
102
3
INT04_0
INT04_1
INT04_2
INT05_0
INT05_1
INT05_2
INT06_0
INT06_1
INT06_2
INT07_0
INT07_1
INT07_2
INT08_0
INT08_1
INT08_2
INT09_0
INT09_1
INT10_0
INT10_1
INT10_2
INT11_0
INT11_1
INT11_2
INT12_0
INT12_1
INT12_2
INT13_0
INT13_1
INT13_2
INT14_0
INT14_1
INT14_2
Document Number: 001-99223 Rev.*A
External interrupt request 04 input pin
External interrupt request 05 input pin
External interrupt request 06 input pin
External interrupt request 07 input pin
External interrupt request 08 input pin
External interrupt request 09 input pin
External interrupt request 10 input pin
External interrupt request 11 input pin
External interrupt request 12 input pin
External interrupt request 13 input pin
External interrupt request 14 input pin
Page 24 of 129
S6E1B8 Series
Pin Function
LQFP-120
68
Pin No.
LQFP-100
58
LQFP-80
48
116
54
100
11
12
101
85
13
103
6
26
104
7
28
105
117
77
106
47
78
109
48
79
111
99
80
107
96
85
86
88
6
21
89
7
23
90
97
67
91
42
68
43
69
84
70
92
76
68
6
16
69
7
18
70
77
57
71
32
33
66
72
P00
92
77
61
P01
93
78
62
P02
94
79
63
P03
P04
P05
P06
P07
P08
P09
P0A
P0B
P0C
P0D
P0E
P0F
95
96
97
98
99
100
101
102
103
104
105
106
107
80
81
82
83
84
85
86
87
88
89
90
91
92
64
65
66
67
68
69
70
71
72
Pin Name
Function Description
INT15_0
External
Interrupt
GPIO
INT15_1
INT15_2
INT16_0
INT16_1
INT16_2
INT17_0
INT17_1
INT17_2
INT18_0
INT18_1
INT18_2
INT19_0
INT19_1
INT19_2
INT20_0
INT20_1
INT20_2
INT21_0
INT21_1
INT21_2
INT22_0
INT22_1
INT22_2
INT23_0
INT23_1
INT23_2
NMIX
Document Number: 001-99223 Rev.*A
External interrupt request 15 input pin
External interrupt request 16 input pin
External interrupt request 17 input pin
External interrupt request 18 input pin
External interrupt request 19 input pin
External interrupt request 20 input pin
External interrupt request 21 input pin
External interrupt request 22 input pin
External interrupt request 23 input pin
Non-Maskable Interrupt input pin
General-purpose I/O port 0
Page 25 of 129
S6E1B8 Series
Pin Function
GPIO
P10
LQFP-120
62
Pin No.
LQFP-100
52
LQFP-80
42
P11
63
53
43
P12
64
54
44
P13
65
55
45
P14
P15
P16
P17
P18
P19
P1A
P1B
P1C
P1D
P1E
P20
P21
P22
P23
P24
P25
P26
P27
P28
P30
P31
P32
P33
P34
P35
P36
P37
P38
P39
P3A
66
67
68
69
74
75
76
77
78
79
80
89
88
87
86
85
84
83
82
81
14
15
16
17
18
19
20
21
22
23
24
56
57
58
59
64
65
66
67
68
69
70
74
73
72
71
9
10
11
12
13
14
15
16
17
18
19
46
47
48
49
54
55
56
57
60
59
58
9
10
11
12
13
14
P3B
25
20
15
P3C
26
21
16
P3D
27
22
17
P3E
P3F
28
29
23
24
18
19
Pin Name
Document Number: 001-99223 Rev.*A
Function Description
General-purpose I/O port 1
General-purpose I/O port 2
General-purpose I/O port 3
Page 26 of 129
S6E1B8 Series
Pin Function
Pin Name
P40
P41
P42
P43
P44
P45
P46
P47
P48
P49
P4A
P4B
P4C
P4D
P50
GPIO
P51
P52
P53
P54
P55
P56
P57
P58
P59
P5A
P5B
P60
P61
P62
P63
P64
P65
P66
P67
P68
P70
P71
P72
P73
P74
P80
P81
Function Description
General-purpose I/O port 4
General-purpose I/O port 5
General-purpose I/O port 6
General-purpose I/O port 7
General-purpose I/O port 8
P82
PE0*
PE2
PE3
Document Number: 001-99223 Rev.*A
General-purpose I/O port E
LQFP-120
32
33
34
35
36
37
42
43
44
45
47
48
49
50
2
Pin No.
LQFP-100
27
28
29
30
31
32
37
38
39
40
42
43
44
45
2
LQFP-80
21
22
27
28
29
30
32
33
34
35
2
3
4
5
6
7
8
9
10
11
12
13
116
115
114
113
112
111
110
109
108
51
52
53
54
55
117
118
3
4
5
6
7
8
96
95
94
93
97
98
3
4
5
6
7
8
76
75
74
73
77
78
119
99
79
56
46
36
58
59
48
49
38
39
Page 27 of 129
S6E1B8 Series
Pin Function
Pin Name
Function Description
SIN0_0
SIN0_1
Multi-function serial interface ch.0 input pin
SOT0_0
(SDA0_0)
Multi-function
Serial 0
SOT0_1
(SDA0_1)
SCK0_0
(SCL0_0)
SCK0_1
(SCL0_1)
Multi-function
Serial 1
Multi-function
Serial 2
SIN1_0
SIN1_1
SIN1_2
SOT1_0
(SDA1_0)
SOT1_1
(SDA1_1)
SOT1_2
(SDA1_2)
SCK1_0
(SCL1_0)
SCK1_1
(SCL1_1)
SCK1_2
(SCL1_2)
SIN2_0
SIN2_1
SIN2_2
SOT2_0
(SDA2_0)
SOT2_1
(SDA2_1)
SOT2_2
(SDA2_2)
SCK2_0
(SCL2_0)
SCK2_1
(SCL2_1)
SCK2_2
(SCL2_2)
Document Number: 001-99223 Rev.*A
Multi-function serial interface ch.0 output
pin.
This pin operates as SOT0 when used as a
UART/CSIO/LIN pin (operation mode 0 to 3)
2
and as SDA0 when used as an I C pin
(operation mode 4).
Multi-function serial interface ch.0 clock I/O
pin.
This pin operates as SCK0 when used as a
CSIO pin (operation mode 2) and as SCL0
2
when used as an I C pin (operation mode
4).
Multi-function serial interface ch.1 input pin
Multi-function serial interface ch.1 output
pin.
This pin operates as SOT1 when used as a
UART/CSIO/LIN pin (operation mode 0 to 3)
2
and as SDA1 when used as an I C pin
(operation mode 4).
LQFP-120
88
66
Pin No.
LQFP-100
73
56
LQFP-80
60
46
87
72
59
67
57
47
86
71
58
68
58
48
8
63
32
53
27
43
-
9
-
-
64
54
44
33
28
-
Multi-function serial interface ch.1 clock I/O
pin.
This pin operates as SCK1 when used as a
CSIO pin (operation mode 2) and as SCL1
2
when used as an I C pin (operation mode
4).
10
-
-
65
55
45
34
29
-
Multi-function serial interface ch.2 input pin
53
85
69
59
49
Multi-function serial interface ch.2 output
pin.
This pin operates as SOT2 when used as a
UART/CSIO/LIN pin (operation mode 0 to 3)
2
and as SDA2 when used as an I C pin
(operation mode 4).
54
-
-
84
-
-
74
64
54
Multi-function serial interface ch.1 clock I/O
pin.
This pin operates as SCK2 when used as a
CSIO pin (operation mode 2) and as SCL2
2
when used as an I C pin (operation mode
4).
55
-
-
83
-
-
75
65
55
Page 28 of 129
S6E1B8 Series
Pin Function
Pin Name
Function Description
SIN3_0
SIN3_1
Multi-function
Serial 3
Multi-function
Serial 4
SIN3_2
SOT3_0
(SDA3_0)
SOT3_1
(SDA3_1)
SOT3_2
(SDA3_2)
SCK3_0
(SCL3_0)
SCK3_1
(SCL3_1)
SCK3_2
(SCL3_2)
SIN4_0
SIN4_1
SIN4_2
SOT4_0
(SDA4_0)
SOT4_1
(SDA4_1)
SOT4_2
(SDA4_2)
SCK4_0
(SCL4_0)
SCK4_1
(SCL4_1)
SCK4_2
(SCL4_2)
CTS4_0
CTS4_1
CTS4_2
RTS4_0
RTS4_1
RTS4_2
Document Number: 001-99223 Rev.*A
Multi-function serial interface ch.3 input pin
LQFP-120
110
Pin No.
LQFP-100
-
LQFP-80
-
2
2
2
94
79
63
Multi-function serial interface ch.3 output
pin.
This pin operates as SOT3 when used as a
UART/CSIO/LIN pin (operation mode 0 to 3)
2
and as SDA3 when used as an I C pin
(operation mode 4).
109
-
-
3
3
3
92
77
61
Multi-function serial interface ch.3 clock I/O
pin.
This pin operates as SCK3 when used as a
CSIO (operation mode 2) and as SCL3
2
when used as an I C pin (operation mode
4).
108
-
-
4
4
4
96
81
65
102
76
97
87
66
82
67
56
-
Multi-function serial interface ch.4 output
pin.
This pin operates as SOT4 when used as a
UART/CSIO/LIN pin (operation mode 0 to 3)
2
and as SDA4 when used as an I C pin
(operation mode 4).
99
84
66
77
67
57
98
83
-
Multi-function serial interface ch.4 clock I/O
pin.
This pin operates as SCK4 when used as a
CSIO (operation mode 2) and as SCL4
2
when used as an I C pin (operation mode
4).
107
92
72
78
68
-
99
84
66
106
79
100
105
80
101
91
69
85
90
70
86
71
70
-
Multi-function serial interface ch.4 input pin
Multi-function serial interface ch4 CTS input
pin
Multi-function serial interface ch4 RTS
output pin
Page 29 of 129
S6E1B8 Series
Pin Function
Pin Name
SIN5_0
(MI2SDI5_0)
SIN5_1
SIN5_2
SOT5_0
(SDA5_0)
(MI2SDO5_0)
SOT5_1
(SDA5_1)
Multi-function
Serial 5
SOT5_2
(SDA5_2)
SCK5_0
(SCL5_0)
(MI2SCK5_0)
SCK5_1
(SCL5_1)
SCK5_2
(SCL5_2)
MI2SWS5_0
SIN6_0
SIN6_1
(MI2SDI6_1)
SOT6_0
(SDA6_0)
SOT6_1
(SDA6_1)
(MI2SDO6_1)
Multi-function
Serial 6
SCK6_0
(SCL6_0)
SCK6_1
(SCL6_1)
(MI2SCK6_1)
SCS60_1
SCS61_1
SCS62_1
MI2SWS6_1
Document Number: 001-99223 Rev.*A
Function Description
Multi-function serial interface ch.5 input pin.
SIN5_0 pin operates as I2SIN5_0 when
2
used as an I S pin (operation mode 2).
Multi-function serial interface ch.5 output
pin.
This pin operates as SOT5 when used as a
UART/CSIO/LIN pin (operation mode 0 to 3)
2
and as SDA5 when used as an I C pin
(operation mode 4).
SOT5_0 pin operates as MI2SDO5_0 when
2
used as an I S pin (operation mode 2).
Multi-function serial interface ch.5 clock I/O
pin.
This pin operates as SCK5 when used as a
CSIO (operation mode 2) and as SCL5
2
when used as an I C pin (operation mode
4).
SCK5_0 pin operates as MI2SCK5_0 when
2
used as an I S pin (operation mode 2).
2
I S word select (WS) output
Multi-function serial interface ch.6 input pin.
SIN6_1 pin operates as I2SIN6_1 when
2
used as an I S pin (operation mode 2).
Multi-function serial interface ch.6 output
pin.
This pin operates as SOT6 when used as a
UART/CSIO/LIN pin (operation mode 0 to 3)
2
and as SDA6 when used as an I C pin
(operation mode 4).
SOT6_1 pin operates as MI2SDO6_1 when
2
used as an I S pin (operation mode 2).
Multi-function serial interface ch.6 clock I/O
pin.
This pin operates as SCK6 when used as a
CSIO (operation mode 2) and as SCL6
2
when used as an I C pin (operation mode
4).
SCK6_6 pin operates as MI2SCK6_1 when
2
used as an I S pin (operation mode 2).
Multi-function serial interface ch.6 serial
chip select 0 output pin.
Multi-function serial interface ch.6 serial
chip select 1 output pin.
Multi-function serial interface ch.6 serial
chip select 2 output pin.
2
I S word select (WS) output
LQFP-120
Pin No.
LQFP-100
LQFP-80
116
96
76
113
20
15
-
115
95
75
112
-
-
21
16
-
114
94
74
111
-
-
22
17
-
113
5
93
5
73
5
17
12
12
6
6
6
16
11
11
7
7
7
15
10
10
14
9
9
18
13
-
19
14
-
14
9
9
Page 30 of 129
S6E1B8 Series
Pin Function
Multi-function
Serial 7
Pin Name
SIN7_0
SIN7_1
SIN7_2
SOT7_0
(SDA7_0)
SOT7_1
(SDA7_1)
SOT7_2
(SDA7_2)
SCK7_0
(SCL7_0)
SCK7_1
(SCL7_1)
SCK7_2
(SCL7_2)
SCS70_1
SCS71_1
SCS72_1
Smart Card
Interface 0
Smart Card
Interface 1
USB
IC0_VCC_0
IC0_VCC_1
IC0_VPEN_0
IC0_VPEN_1
IC0_RST_0
IC0_RST_1
IC0_CIN_0
IC0_CIN_1
IC0_CLK_0
IC0_CLK_1
IC0_DATA_0
IC0_DATA_1
IC1_VCC_0
IC1_VCC_1
IC1_VPEN_0
IC1_VPEN_1
IC1_RST_0
IC1_RST_1
IC1_CIN_0
IC1_CIN_1
IC1_CLK_0
IC1_CLK_1
IC1_DATA_0
IC1_DATA_1
UDM0
UDP0
UHCONX0
Document Number: 001-99223 Rev.*A
Function Description
Multi-function serial interface ch.7 input pin
Multi-function serial interface ch.7 output
pin.
This pin operates as SOT7 when used as a
UART/CSIO/LIN pin (operation mode 0 to 3)
2
and as SDA7 when used as an I C pin
(operation mode 4).
Multi-function serial interface ch.7 clock I/O
pin.
This pin operates as SCK7 when used as a
CSIO (operation mode 2) and as SCL7
2
when used as an I C pin (operation mode
4).
Multi-function serial interface ch.7 serial
chip select 0 output pin.
Multi-function serial interface ch.7 serial
chip select 1 output pin.
Multi-function serial interface ch.7 serial
chip select 2 output pin.
Smart card ch.0 power enable output pin
Smart card ch.0 programming output pin
Smart card ch.0 reset output pin
Smart card ch.0 insert detection input pin
Smart card ch.0 serial interface clock output
pin
Smart card ch.0 serial interface data
input/output pin
Smart card ch.1 power enable output pin
Smart card ch.1 programming output pin
Smart card ch.1 reset output pin
Smart card ch.1 insert detection input pin
Smart card ch.1 serial interface clock output
pin
Smart card ch.1 serial interface data
input/output pin
USB device/host D – pin
USB device/host D + pin
USB external pull-up control pin
LQFP-120
11
48
117
Pin No.
LQFP-100
43
97
LQFP-80
33
77
12
-
-
49
44
34
118
98
78
13
-
-
50
45
35
119
99
79
47
42
32
51
-
-
52
-
-
106
33
105
34
114
35
102
37
107
32
113
36
28
63
27
64
26
65
24
67
29
62
25
66
103
104
102
91
28
90
29
94
30
87
32
92
27
93
31
23
53
22
54
21
55
19
57
24
52
20
56
88
89
87
71
70
74
67
22
72
73
21
18
43
17
44
16
45
14
47
19
42
15
46
68
69
67
Page 31 of 129
S6E1B8 Series
Pin Function
LQFP-120
23
Pin No.
LQFP-100
18
LQFP-80
13
79
69
-
115
95
75
18
13
-
80
70
-
63
22
75
64
53
17
65
54
43
55
44
IC01_0
21
16
-
IC01_1
76
66
56
65
55
45
20
15
-
77
66
19
78
67
56
14
68
57
46
-
67
57
47
24
19
14
86
71
58
25
20
15
85
-
-
26
21
16
84
-
-
27
22
17
83
-
-
28
23
18
82
-
-
29
24
19
81
-
-
48
116
43
96
33
76
Pin Name
DTTI0X_0
DTTI0X_1
DTTI0X_2
FRCK0_0
FRCK0_1
FRCK0_2
IC00_0
IC00_1
IC00_2
IC01_2
IC02_0
IC02_1
IC02_2
IC03_0
IC03_1
Function Description
Input signal of waveform generator
controlling RTO00 to RTO05 outputs of
Multi-function Timer 0.
16-bit free-run timer ch.0 external clock
input pin.
16-bit input capture input pin of
Multi-function
timer 0.
ICxx describes channel number.
IC03_2
Multi-function
Timer 0
RTO00_0
(PPG00_0)
RTO00_1
(PPG00_1)
RTO01_0
(PPG00_0)
RTO01_1
(PPG00_1)
RTO02_0
(PPG02_0)
RTO02_1
(PPG02_1)
RTO03_0
(PPG02_0)
RTO03_1
(PPG02_1)
RTO04_0
(PPG04_0)
RTO04_1
(PPG04_1)
RTO05_0
(PPG04_0)
RTO05_1
(PPG04_1)
IGTRG0_0
IGTRG0_1
Document Number: 001-99223 Rev.*A
Waveform generator output pin of
Multi-function timer 0.
This pin operates as PPG00 when it is used
in PPG0 output mode.
Waveform generator output pin of
Multi-function timer 0.
This pin operates as PPG00 when it is used
in PPG0 output mode.
Waveform generator output pin of
Multi-function timer 0.
This pin operates as PPG02 when it is used
in PPG0 output mode.
Waveform generator output pin of
Multi-function timer 0.
This pin operates as PPG02 when it is used
in PPG0 output mode.
Waveform generator output pin of
Multi-function timer 0.
This pin operates as PPG04 when it is used
in PPG0 output mode.
Waveform generator output pin of
Multi-function timer 0.
This pin operates as PPG04 when it is used
in PPG0 output mode.
PPG IGBT mode external trigger input pin
Page 32 of 129
S6E1B8 Series
Pin Function
LQFP-120
107
Pin No.
LQFP-100
92
LQFP-80
72
65
55
45
24
19
14
107
92
72
65
24
55
19
45
14
49
44
34
116
8
6
96
8
6
76
8
6
5
5
5
4
4
4
VV3
3
3
3
VV4
2
2
2
117
97
77
Pin Name
RTCCO_0
RTCCO_1
Real-time
Clock
RTCCO_2
0.5-seconds pulse output pin of Real-time
clock
SUBOUT_0
SUBOUT_1
SUBOUT_2
HDMI-CEC/
Remote
Control
Reception
Function Description
CEC0_0
CEC1_0
CEC1_1
VV0
Sub clock output pin
HDMI-CEC/Remote Control Reception ch.0
input/output pin
HDMI-CEC/Remote Control Reception ch.1
input/output pin
VV1
VV2
C0
C1
LCD controller power supply I/O pin
LCD controller flying capacitor output pin
118
98
78
COM0
26
21
16
COM1
25
20
15
COM2
24
19
14
23
18
13
COM3
COM4
LCD controller common output pin
17
12
12
COM5
16
11
11
COM6
15
10
10
COM7
14
9
9
LCD
SEG00
115
95
75
Controller
SEG01
114
94
74
SEG02
113
93
73
SEG03
106
91
71
SEG04
105
90
70
SEG05
101
86
-
SEG06
100
85
-
SEG07
99
84
66
98
83
-
SEG09
97
82
-
SEG10
89
74
-
SEG11
88
73
60
SEG12
87
72
59
SEG13
86
71
58
SEG14
79
69
-
SEG15
78
68
-
SEG16
77
67
57
SEG08
Document Number: 001-99223 Rev.*A
LCD controller segment output pin
Page 33 of 129
S6E1B8 Series
Pin Function
LCD
Controller
LowPower
Consumption
Mode
SEG17
LQFP-120
76
Pin No.
LQFP-100
66
LQFP-80
56
SEG18
75
65
55
SEG19
74
64
54
SEG20
69
59
49
SEG21
68
58
48
SEG22
67
57
47
SEG23
66
56
46
SEG24
65
55
45
SEG25
64
54
44
SEG26
63
53
43
SEG27
62
52
42
SEG28
50
45
35
SEG29
49
44
34
48
43
33
47
42
32
SEG32
37
32
22
SEG33
36
31
21
SEG34
29
24
19
SEG35
28
23
18
SEG36
27
22
17
SEG37
19
14
-
SEG38
8
8
8
SEG39
7
7
7
SEG40
17
12
12
SEG41
16
11
11
SEG42
15
10
10
SEG43
14
9
9
WKUP0
107
92
72
WKUP1
63
53
43
WKUP2
88
73
60
WKUP3
116
96
76
WKUP4
14
9
9
102
87
67
50
45
35
WKUP7
48
43
33
WKUP8
28
23
18
WKUP9
8
8
8
WKUP10
WKUP11
97
20
82
15
-
Pin Name
SEG30
SEG31
WKUP5
WKUP6
Document Number: 001-99223 Rev.*A
Function Description
LCD controller segment output pin
Deep standby mode return signal input pin
Page 34 of 129
S6E1B8 Series
Pin Function
VBAT
Pin Name
Function Description
LVDI
Input pin to monitor the external voltage.
The return signal input pin from a
hibernation state
On-board regulator control pin
External Reset Input pin.
A reset is valid when INITX="L".
Mode 0 pin.
During normal operation, input MD0="L".
During serial programming to Flash
memory, input MD0="H".
Mode 1 pin.
During normal operation, input is not
needed.
During serial programming to Flash
memory, MD1 = "L" must be input.
VWAKEUP
REGCTL
Reset
INITX
MD0
Mode
MD1
Power
VBAT power
GND
Clock
VCC
VBAT
VSS
GND pin
LQFP-80
22
45
40
30
44
39
29
41
36
26
57
47
37
56
46
36
1
1
1
31
26
-
40
35
25
61
51
41
91
76
-
46
41
31
30
25
20
39
34
24
60
50
40
90
75
-
120
100
80
Main clock (oscillation) input pin
58
48
38
X0A
Sub clock (oscillation) input pin
42
37
27
X1
Main clock (oscillation) I/O pin
59
49
39
Sub clock (oscillation) I/O pin
Built-in high-speed CR oscillation clock
output port
Built-in high-speed CR oscillation clock
output port
A/D converter analog power supply pin
A/D converter analog reference voltage
input pin
A/D converter analog reference voltage
input pin
Power supply stabilization capacitance pin
43
38
28
89
74
-
107
92
72
70
60
50
73
63
53
71
61
51
38
33
23
X1A
CROUT_1
Analog
GND
C pin
VBAT power supply pin
Backup power supply (battery etc.) and
system power supply
Pin No.
LQFP-100
32
X0
CROUT_0
Analog
Power
Power supply pin
LQFP-120
37
AVCC
AVRH
AVSS
C
*: PE0 is an open drain pin, cannot output high.
Document Number: 001-99223 Rev.*A
Page 35 of 129
S6E1B8 Series
5. I/O Circuit Type
Type
Circuit
Remarks
Pull-up
resistor
P-ch
P-ch
Digital output
X1
N-ch
Digital output
R
It is possible to select the main
oscillation / GPIO function
Pull-up resistor control
Digital input
Standby mode control
Feedback
resistor
A
Clock input
When the main oscillation is selected.
Oscillation feedback resistor
: Approximately 1 MΩ
With standby mode control
When the GPIO is selected.
CMOS level output.
CMOS level hysteresis input
Standby mode control
Digital input
Pull-up
Standby mode control
resistor
R
P-ch
P-ch
X0
N-ch
With pull-up resistor control
With standby mode control
Pull-up resistor
: Approximately 33 kΩ
IOH = -4mA, IOL= 4 mA
Digital output
Digital output
Pull-up resistor control
Document Number: 001-99223 Rev.*A
Page 36 of 129
S6E1B8 Series
Type
Circuit
Remarks
Pull-up resistor
CMOS level hysteresis input
Digital input
B
Pull-up resistor
: Approximately 33 kΩ
Digital input
C
Digital output
N-ch
X0A
R
Digital input
D
Sub OSC/GPIO
select
Open drain output
CMOS level hysteresis input
・CMOS level output
・ Please refer to the "VBAT domain"
setting of IO in of the “Peripheral
Manual main part (MN710-00001)".
OSC
X1A
R
Digital input
Sub OSC/ GPIO
select
OSC
E
RX
It is possible to select the sub
oscillation / GPIO function
When the sub oscillation is selected.
・Oscillation feedback resistor
: Approximately 12 MΩ
When the GPIO is selected.
・CMOS level hysteresis input
Sub OSC enable
・Please refer to the "VBAT domain"
setting of IO in the “Peripheral Manual
Clock input
Document Number: 001-99223 Rev.*A
main part (MN710-00001)" .
Page 37 of 129
S6E1B8 Series
Type
Circuit
Remarks
・ CMOS level output
P-ch
P-ch
Digital output
・ CMOS level hysteresis input
・ With pull-up resistor control
・ With standby mode control
・ Pull-up resistor
F
: Approximately 33 kΩ
N-ch
Digital output
・ IOH = -4 mA, IOL = 4 mA
・ When this pin is used as an I2C pin, the
R
digital output P-ch transistor is always
off
Pull-up resistor control
Digital input
Standby mode control
P-ch
P-ch
Digital output
・ CMOS level output
・ CMOS level hysteresis input
・ With input control
N-ch
Digital output
・ Analog input
・ With pull-up resistor control
・ With standby mode control
G
・ Pull-up resistor
R
Pull-up resistor control
Digital input
Standby mode control
: Approximately 33 kΩ
・ IOH= -4 mA, IOL= 4 mA
・ When this pin is used as an I2C pin, the
digital output P-ch transistor is always
off
Analog input
Input control
Document Number: 001-99223 Rev.*A
Page 38 of 129
S6E1B8 Series
Type
Circuit
P-ch
P-ch
Remarks
Digital output
・ CMOS level output
・ CMOS level hysteresis input
・ With input control
・ Analog input
N-ch
Digital output
・ 5 V tolerant
・ With pull-up resistor control
・ With standby mode control
H
・ Pull-up resistor
Pull-up resistor control
R
Digital input
Standby mode control
: Approximately 33 kΩ
・ IOH= -4 mA, IOL= 4 mA
・ Available to control of PZR registers.
・ When this pin is used as an I2C pin, the
digital output P-ch transistor is always
off
Analog input
Input control
・ CMOS level output
P-ch
P-ch
Digital output
・ CMOS level hysteresis input
・ 5 V tolerant
・ With pull-up resistor control
・ With standby mode control
I
N-ch
Digital output
・ Pull-up resistor
: Approximately 33 kΩ
・ IOH= -4 mA, IOL= 4 mA
R
・ Available to control PZR registers
Pull-up resistor control
Digital input
・ When this pin is used as an I2C pin, the
digital output P-ch transistor is always
off
Standby mode control
Document Number: 001-99223 Rev.*A
Page 39 of 129
S6E1B8 Series
Type
Circuit
Remarks
Mode input
J
・ CMOS level hysteresis input
GPIO Digital output
GPIO Digital input/output direction
GPIO Digital input
GPIO Digital input circuit control
UDP output
UDP0/P0C
USB Full-speed/Low-speed control
UDP input
K
Di fferential
UDM0/P0B
It is possible to select the USB I/O / GPIO
function.
When the USB I/O is selected.
Full-speed, Low-speed control
Differential input
USB/GPIO select
UDM input
UDM output
USB Digital input/output direction
GPIO Digital output
When the GPIO is selected.
CMOS level output
CMOS level hysteresis input
With standby mode control
IOH= -39 mA, IOL= 39 mA
GPIO Digital input/output direction
GPIO Digital input
GPIO Digital input circuit control
Document Number: 001-99223 Rev.*A
Page 40 of 129
S6E1B8 Series
Type
Circuit
P-ch
P-ch
Remarks
Digital output
・ CMOS level output
・ CMOS level hysteresis input
・ With input control
・ 5 V tolerant
N-ch
Digital output
・ LCD segment output
・ With pull-up resistor control
L
・ With standby mode control
・ Pull-up resistor
R
Pull-up resistor control
Digital input
Standby mode control
: Approximately 33 kΩ
・ IOH= -4 mA, IOL= 4 mA
・ Available to control of PZR registers.
・ When this pin is used as an I2C pin, the
digital output P-ch transistor is always off
LCD output
LCD control
Document Number: 001-99223 Rev.*A
Page 41 of 129
S6E1B8 Series
Type
Circuit
P-ch
P-ch
Remarks
Digital output
・ CMOS level output
・ CMOS level hysteresis input
N-ch
Digital output
・ With input control
・ 5 V tolerant
・ LCD common output
・ LCD segment output
M
R
Pull-up resistor control
Digital input
Standby mode control
・ With pull-up resistor control
・ With standby mode control
・ Pull-up resistor
: Approximately 33 kΩ
・ IOH = -4 mA, IOL = 4 mA
・ Available to control of PZR registers.
LCD output
・ When this pin is used as an I2C pin, the
digital output P-ch transistor is always
off
LCD control
LCD output
LCD control
Document Number: 001-99223 Rev.*A
Page 42 of 129
S6E1B8 Series
Type
Circuit
P-ch
P-ch
Remarks
Digital output
・ CMOS level output
・ CMOS level hysteresis input
・ With input control
N-ch
Digital output
・ 5 V tolerant
・ LCD common output
N
・ With pull-up resistor control
・ With standby mode control
R
Pull-up resistor control
Digital input
Standby mode control
・ Pull-up resistor
: Approximately 33 kΩ
・ IOH=-4 mA, IOL= 4 mA
・ Available to control of PZR registers.
LCD output
LCD control
Digital output
・ CMOS level output
・ CMOS level hysteresis input
・ With input control
・ Analog output
Digital output
・ 5 V tolerant
・ With pull-up resistor control
O
・ With standby mode control
・ Pull-up resistor
Pull-up resistor control
: Approximately 33 kΩ
・ IOH= -4 mA, IOL= 4 mA
Digital input
Standby mode control
・ Available to control of PZR registers.
・ When this pin is used as an I2C pin, the
digital output P-ch transistor is always off
Analog output
Document Number: 001-99223 Rev.*A
Page 43 of 129
S6E1B8 Series
Type
Circuit
P-ch
P-ch
Remarks
Digital output
・ CMOS level output
・ CMOS level hysteresis input
N-ch
Digital output
・ With input control
・ Analog input
・ 5 V tolerant
・ LCD segment output
P
R
Pull-up resistor control
Digital input
Standby mode control
・ With pull-up resistor control
・ With standby mode control
・ Pull-up resistor
: Approximately 33 kΩ
・ IOH = -4 mA, IOL = 4 mA
・ Available to control of PZR registers.
Analog input
・ When this pin is used as an I2C pin, the
digital output P-ch transistor is always off
Input control
LCD output
LCD control
Document Number: 001-99223 Rev.*A
Page 44 of 129
S6E1B8 Series
Type
Circuit
P-ch
P-ch
Remarks
Digital output
・ CMOS level output
・ CMOS level hysteresis input
・ With input control
・ 5 V tolerant
N-ch
Digital output
・ LCD VV input/output
・ With pull-up resistor control
・ With standby mode control
Q
・ Pull-up resistor
: Approximately 33 kΩ
R
Pull-up resistor control
・ IOH = -4 mA, IOL= 4 mA
Digital input
・ Available to control of PZR registers.
Standby mode control
・ When this pin is used as an I2C pin, the
digital output P-ch transistor is always
off
LCD VV
input/output
LCD VV control
Document Number: 001-99223 Rev.*A
Page 45 of 129
S6E1B8 Series
6. Handling Precautions
Any semiconductor devices have inherently a certain rate of failure. The possibility of failure is greatly affected by the conditions in
which they are used (circuit conditions, environmental conditions, etc.). This page describes precautions that must be observed to
minimize the chance of failure and to obtain higher reliability from your Cypress semiconductor devices.
6.1
Precautions for Product Design
This section describes precautions when designing electronic equipment using semiconductor devices.
Absolute Maximum Ratings
Semiconductor devices can be permanently damaged by application of stress (voltage, current, temperature, etc.) in excess of
certain established limits, called absolute maximum ratings. Do not exceed these ratings.
Recommended Operating Conditions
Recommended operating conditions are normal operating ranges for the semiconductor device. All the device's electrical
characteristics are warranted when operated within these ranges.
Always use semiconductor devices within the recommended operating conditions. Operation outside these ranges may adversely
affect reliability and could result in device failure.
No warranty is made with respect to uses, operating conditions, or combinations not represented on the data sheet. Users
considering application outside the listed conditions are advised to contact their sales representative beforehand.
Processing and Protection of Pins
These precautions must be followed when handling the pins which connect semiconductor devices to power supply and input/output
functions.
(1) Preventing Over-Voltage and Over-Current Conditions
Exposure to voltage or current levels in excess of maximum ratings at any pin is likely to cause deterioration within the device,
and in extreme cases leads to permanent damage of the device. Try to prevent such overvoltage or over-current conditions at
the design stage.
(2) Protection of Output Pins
Shorting of output pins to supply pins or other output pins, or connection to large capacitance can cause large current flows.
Such conditions if present for extended periods of time can damage the device.
Therefore, avoid this type of connection.
(3) Handling of Unused Input Pins
Unconnected input pins with very high impedance levels can adversely affect stability of operation. Such pins should be
connected through an appropriate resistance to a power supply pin or ground pin.
Document Number: 001-99223 Rev.*A
Page 46 of 129
S6E1B8 Series
Latch-Up
Semiconductor devices are constructed by the formation of P-type and N-type areas on a substrate. When subjected to abnormally
high voltages, internal parasitic PNPN junctions (called thyristor structures) may be formed, causing large current levels in excess of
several hundred mA to flow continuously at the power supply pin. This condition is called latch-up.
CAUTION: The occurrence of latch-up not only causes loss of reliability in the semiconductor device, but can cause injury or
damage from high heat, smoke or flame. To prevent this from happening, do the following:
(1) Be sure that voltages applied to pins do not exceed the absolute maximum ratings. This should include attention to
abnormal noise, surge levels, etc.
(2) Be sure that abnormal current flows do not occur during the power-on sequence.
Observance of Safety Regulations and Standards
Most countries in the world have established standards and regulations regarding safety, protection from electromagnetic
interference, etc. Customers are requested to observe applicable regulations and standards in the design of products.
Fail-Safe Design
Any semiconductor devices have inherently a certain rate of failure. You must protect against injury, damage or loss from such
failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and
prevention of over-current levels and other abnormal operating conditions.
Precautions Related to Usage of Devices
Cypress semiconductor devices are intended for use in standard applications (computers, office automation and other office
equipment, industrial, communications, and measurement equipment, personal or household devices, etc.).
CAUTION: Customers considering the use of our products in special applications where failure or abnormal operation may directly
affect human lives or cause physical injury or property damage, or where extremely high levels of reliability are demanded (such as
aerospace systems, atomic energy controls, sea floor repeaters, vehicle operating controls, medical devices for life support, etc.)
are requested to consult with sales representatives before such use. The company will not be responsible for damages arising from
such use without prior approval.
6.2
Precautions for Package Mounting
Package mounting may be either lead insertion type or surface mount type. In either case, for heat resistance during soldering, you
should only mount under Cypress's recommended conditions. For detailed information about mount conditions, contact your sales
representative.
Lead Insertion Type
Mounting of lead insertion type packages onto printed circuit boards may be done by two methods: direct soldering on the board, or
mounting by using a socket.
Direct mounting onto boards normally involves processes for inserting leads into through-holes on the board and using the flow
soldering (wave soldering) method of applying liquid solder. In this case, the soldering process usually causes leads to be subjected
to thermal stress in excess of the absolute ratings for storage temperature. Mounting processes should conform to Cypress
recommended mounting conditions.
If socket mounting is used, differences in surface treatment of the socket contacts and IC lead surfaces can lead to contact
deterioration after long periods. For this reason it is recommended that the surface treatment of socket contacts and IC leads be
verified before mounting.
Document Number: 001-99223 Rev.*A
Page 47 of 129
S6E1B8 Series
Surface Mount Type
Surface mount packaging has longer and thinner leads than lead-insertion packaging, and therefore leads are more easily deformed
or bent. The use of packages with higher pin counts and narrower pin pitch results in increased susceptibility to open connections
caused by deformed pins, or shorting due to solder bridges.
You must use appropriate mounting techniques. Cypress recommends the solder reflow method, and has established a ranking of
mounting conditions for each product. Users are advised to mount packages in accordance with Cypress ranking of recommended
conditions.
Lead-Free Packaging
CAUTION: When ball grid array (BGA) packages with Sn-Ag-Cu balls are mounted using Sn-Pb eutectic soldering, junction strength
may be reduced under some conditions of use.
Storage of Semiconductor Devices
Because plastic chip packages are formed from plastic resins, exposure to natural environmental conditions will cause absorption of
moisture. During mounting, the application of heat to a package that has absorbed moisture can cause surfaces to peel, reducing
moisture resistance and causing packages to crack. To prevent, do the following:
(1) Avoid exposure to rapid temperature changes, which cause moisture to condense inside the product.
Store products in locations where temperature changes are slight.
(2) Use dry boxes for product storage. Products should be stored below 70% relative humidity, and at temperatures between 5 ˚C
and 30 ˚C.
When you open Dry Package that recommends humidity 40% to 70% relative humidity.
(3) When necessary, Cypress packages semiconductor devices in highly moisture-resistant aluminum laminate bags, with a silica
gel desiccant. Devices should be sealed in their aluminum laminate bags for storage.
(4) Avoid storing packages where they are exposed to corrosive gases or high levels of dust.
Baking
Packages that have absorbed moisture may be de-moisturized by baking (heat drying). Follow the Cypress recommended
conditions for baking.
Condition: 125°C/24 h
Static Electricity
Because semiconductor devices are particularly susceptible to damage by static electricity, you must take the following precautions:
(1) Maintain relative humidity in the working environment between 40% and 70%.
Use of an apparatus for ion generation may be needed to remove electricity.
(2) Electrically ground all conveyors, solder vessels, soldering irons and peripheral equipment.
(3) Eliminate static body electricity by the use of rings or bracelets connected to ground through high resistance (on the level of 1
MΩ).
Wearing of conductive clothing and shoes, use of conductive floor mats and other measures to minimize shock loads is
recommended.
(4) Ground all fixtures and instruments, or protect with anti-static measures.
(5) Avoid the use of styrofoam or other highly static-prone materials for storage of completed board assemblies.
Document Number: 001-99223 Rev.*A
Page 48 of 129
S6E1B8 Series
6.3
Precautions for Use Environment
Reliability of semiconductor devices depends on ambient temperature and other conditions as described above.
For reliable performance, do the following:
(1) Humidity
Prolonged use in high humidity can lead to leakage in devices as well as printed circuit boards. If high humidity levels are
anticipated, consider anti-humidity processing.
(2) Discharge of Static Electricity
When high-voltage charges exist close to semiconductor devices, discharges can cause abnormal operation. In such cases,
use anti-static measures or processing to prevent discharges.
(3) Corrosive Gases, Dust, or Oil
Exposure to corrosive gases or contact with dust or oil may lead to chemical reactions that will adversely affect the device. If
you use devices in such conditions, consider ways to prevent such exposure or to protect the devices.
(4) Radiation, Including Cosmic Radiation
Most devices are not designed for environments involving exposure to radiation or cosmic radiation. Users should provide
shielding as appropriate.
(5) Smoke, Flame
CAUTION: Plastic molded devices are flammable, and therefore should not be used near combustible substances. If devices
begin to smoke or burn, there is danger of the release of toxic gases.
Customers considering the use of Cypress products in other special environmental conditions should consult with sales
representatives.
Document Number: 001-99223 Rev.*A
Page 49 of 129
S6E1B8 Series
7. Handling Devices
Power Supply Pins
In products with multiple VCC and VSS pins, respective pins at the same potential are interconnected within the device in order to
prevent malfunctions such as latch-up. However, all of these pins should be connected externally to the power supply or ground
lines in order to reduce electromagnetic emission levels, to prevent abnormal operation of strobe signals caused by the rise in the
ground level, and to conform to the total output current rating.
Moreover, connect the current supply source with each Power supply pin and GND pin of this device at low impedance. It is also
advisable that a ceramic capacitor of approximately 0.1 µF be connected as a bypass capacitor between each Power supply pin and
GND pin, between AVCC pin and AVSS pin near this device.
Stabilizing Supply Voltage
A malfunction may occur when the power supply voltage fluctuates rapidly even though the fluctuation is within the recommended
operating conditions of the VCC power supply voltage. As a rule, with voltage stabilization, suppress the voltage fluctuation so that
the fluctuation in VCC ripple (peak-to-peak value) at the commercial frequency (50 Hz/60 Hz) does not exceed 10% of the VCC
value in the recommended operating conditions, and the transient fluctuation rate does not exceed 0.1 V/μs when there is a
momentary fluctuation on switching the power supply.
Crystal Oscillator Circuit
Noise near the X0/X1 and X0A/X1A pins may cause the device to malfunction. Design the printed circuit board so that X0/X1,
X0A/X1A pins, the crystal oscillator, and the bypass capacitor to ground are located as close to the device as possible.
It is strongly recommended that the PC board artwork be designed such that the X0/X1 and X0A/X1A pins are surrounded by
ground plane as this is expected to produce stable operation.
Evaluate oscillation of your using crystal oscillator by your mount board.
Sub Crystal Oscillator
This series sub oscillator circuit is low gain to keep the low current consumption. The crystal oscillator to fill the following conditions
is recommended for sub crystal oscillator to stabilize the oscillation.
Surface mount type
Size: More than 3.2 mm × 1.5 mm
Load capacitance: Approximately 6 pF to 7 pF
Lead type
Load capacitance: Approximately 6 pF to 7 pF
Document Number: 001-99223 Rev.*A
Page 50 of 129
S6E1B8 Series
Using an External Clock
When using an external clock as an input of the main clock, set X0/X1 to the external clock input, and input the clock to X0. X1(PE3)
can be used as a general-purpose I/O port.
Similarly, when using an external clock as an input of the sub clock, set X0A/X1A to the external clock input, and input the clock to
X0A. X1A (P47) can be used as a general-purpose I/O port.
Example of Using an External Clock
Device
X0(X0A)
Can be used as
general-purpose
I/O ports.
Set as
External clock
input
X1(PE3),
X1A (P47)
2
Handling when Using Multi-Function Serial Pin as I C Pin
2
2
If it is using the multi-function serial pin as I C pins, P-ch transistor of digital output is always disabled. However, I C pins need to
2
keep the electrical characteristic like other pins and not to connect to the external I C bus system with power OFF.
C Pin
This series contains the regulator. Be sure to connect a smoothing capacitor (CS) for the regulator between the C pin and the GND
pin. Please use a ceramic capacitor or a capacitor of equivalent frequency characteristics as a smoothing capacitor.
However, some laminated ceramic capacitors have the characteristics of capacitance variation due to thermal fluctuation (F
characteristics and Y5V characteristics). Please select the capacitor that meets the specifications in the operating conditions to use
by evaluating the temperature characteristics of a capacitor.
A smoothing capacitor of about 4.7 μF would be recommended for this series.
C
Device
CS
VSS
GND
Mode Pins (MD0)
Connect the MD pin (MD0) directly to VCC or VSS pins. Design the printed circuit board such that the pull-up/down resistance stays
low, as well as the distance between the mode pins and VCC pins or VSS pins is as short as possible and the connection
impedance is low, when the pins are pulled-up/down such as for switching the pin level and rewriting the Flash memory data. It is
because of preventing the device erroneously switching to test mode due to noise.
Document Number: 001-99223 Rev.*A
Page 51 of 129
S6E1B8 Series
Notes on Power-on
Turn power on/off in the following order or at the same time.
Turning on : VBAT → VCC
VCC → AVCC → AVRH
Turning off : VCC → VBAT
AVRH → AVCC → VCC
Serial Communication
There is a possibility to receive wrong data due to the noise or other causes on the serial communication.
Therefore, design a printed circuit board so as to avoid noise.
Consider the case of receiving wrong data due to noise; perform error detection such as by applying a checksum of data at the end.
If an error is detected, retransmit the data.
Differences in Features Among the Products with Different Memory Sizes and Between Flash Memory
Products and MASK Products
The electric characteristics including power consumption, ESD, latch-up, noise characteristics, and oscillation characteristics among
the products with different memory sizes and between Flash memory products and MASK products are different because chip
layout and memory structures are different.
If you are switching to use a different product of the same series, please make sure to evaluate the electric characteristics.
Pull-Up Function of 5 V Tolerant I/O
Please do not input the signal more than VCC voltage at the time of Pull-Up function use of 5 V tolerant I/O.
Handling when Using Debug Pins
When debug pins (SWDIO/SWCLK) are set to GPIO or other peripheral functions, set them as output only; do not set them as input.
Document Number: 001-99223 Rev.*A
Page 52 of 129
S6E1B8 Series
8. Block Diagram
S6E1B86G
To PIN-Function-Ctrl
SWCLK
SWDIO
SW-DP
Fast
GPIO
Cortex-M0+ Core
@40MHz(Max)
NVIC
Bit Band
Wrapper
WatchDog Timer
(Software)
Clock Reset
Generator
WatchDog Timer
(Hardware)
AHB-APB Bridge
Dual-Timer
Multi-layer AHB (Max 40 MHz)
Flash I/F
System ROM
table
INITX
On-Chip SRAM
64 Kbyte
MTB
Security
DSTC
64ch.
X1
X0A
X1A
AHB-AHB
Bridge
CSV
X0
Source Clock
Main
Osc
PLL
Sub
Osc
CR
4MHz
Vbat domain
CR
100kHz
AVRH
AVRL
ANxx
Hardware Encryption
AES128
USB2.0
(Host/Device)
PHY
LVD Ctrl
12-bit A/D Converter
IRQ-Monitor
Unit 0
LVD
Regulator
VWAKEUP
RTCCO
SUBOUT
Vbat domain
Real-Time Clock
CRC Accelerator
A/D Activation
Compare 3ch.
ICOx
16-bit Input Capture
4ch.
FRCKx
16-bit Free-run Timer
3ch.
16-bit Output
Compare 6ch.
DTTI0x
RTO0x
IGTRGx
PORTCTL
Base Timer
16-bit 16ch.
32-bit 8ch.
AHB-APB Bridge: APB1 (Max 40 MHz)
TIOBx
INTx
NMIX
MD0
MD1
MODE-ctrl
Low-speed CR
Prescaler
Peripheral Clock Gating
GPIO
Waveform Generator
3ch.
Multi-function
Serial I/F
8ch.
(with FIFO)
16-bit PPG
3ch.
I2S Clock Generator
2ch.
Smart Card I/F
2ch.
To Fast GPIO
PIN-Function-Ctrl
P0x
P1x
.
Pxx
SCKx
SINx
SOTx
SCSx
MI2SCKx
MI2SWSx
ICx_CLK
ICx_VCC
ICx_VPEN
ICx_RST
ICx_CIN
ICx_DATA
Deep Standby Ctrl
LCD Ctrl
Voltage booster
Document Number: 001-99223 Rev.*A
VREGCTL
External Interrupt
Controller
24pin + NMI
Multi-function Timer
WKUPx
C
Watch Counter
ADTG
TIOAx
UDP0, UDM0
UHCONX0
Power-On
Reset
CROUT
AVCC
AVSS
On-Chip Flash
560 Kbyte
SEGxx
COMx
VVx
Cx
Page 53 of 129
S6E1B8 Series
9. Memory Map
Memory Map (1)
0x41FF_FFFF
Reserved
0xFFFF_FFFF
Reserved
0xF800_8000
0xF800_0000
IOP(single cycle IO)
Reserved
0xF000_2000
0xF000_1000
MTB_DWT
CM0+-CoresightMTB(SFR)
Cortex-M0 Private
Peripherals
0xF000_0000
0xE000_0000
Reserved
0x4400_0000
0x4200_0000
32Mbytes Bit band alias
Peripherals
0x4000_0000
Reserved
0x2400_0000
0x2200_0000
32Mbytes Bit band alias
Reserved
0x2008_0000
Reserved
CR trimming
Security
0x0008_C000
Reserved
See "Memory map (2)" for
the memory size details.
Document Number: 001-99223 Rev.*A
USB ch.0
Reserved
0x4003_CB00
0x4003_CA00
0x4003_C900
I S Clock Generator
Smart Card I/F
0x4003_C200
0x4003_C100
0x4003_C000
0x4003_B000
0x4003_A000
0x4003_9000
0x4003_8000
0x4003_7000
0x4003_6000
0x4003_5000
0x4003_4000
0x4003_3000
0x4003_2000
0x4003_1000
0x4003_0000
0x4002_F000
0x4002_E000
Peripheral Clock Gating
Low Speed CR Prescaler
RTC
Watch Counter
CRC
MFS
Reserved
USB Clock Generator
LVD / DS mode / Vref Calibration
HDMI-CEC/Remote Control Receiver
GPIO
LCD Controller
Int_Req. Read
EXTI
Reserved
CR Trim
2
Reserved
Reserved
0x4002_8000
0x4002_7000
0x4002_6000
0x4002_5000
0x4002_4000
0x4002_1000
0x4002_0000
Flash
0x0000_0000
DSTC
Reserved
0x4005_0000
0x4004_0000
SRAM
0x2000_0000
0x0010_4000
0x0010_2000
0x0010_0000
0x4006_2000
0x4006_1000
A/DC
Reserved
Base Timer
PPG
Reserved
MFT unit0
Reserved
0x4001_6000
0x4001_5000
Dual Timer
0x4001_3000
0x4001_2000
0x4001_1000
0x4001_0000
SW WDT
HW WDT
Clock/Reset
Reserved
Reserved
0x4000_1000
0x4000_0000
Flash I/F
Page 54 of 129
S6E1B8 Series
Memory Map (2)
S6E1B86G
S6E1B84G
0x2008_0000
0x2008_0000
Reserved
Reserved
0x2001_0000
0x2000_F000
0x2001_0000
SRAM
4 Kbytes
SRAM
60 Kbytes
0x2000_F000
SRAM
4 Kbytes
0x2000_8000
SRAM
28 Kbytes
0x2000_0000
Reserved
Reserved
0x0010_4000
0x0010_2000
CR trimming
0x0010_4000
0x0010_2000
CR trimming
0x0010_0000
Security
0x0010_0000
Security
0x0008_C000
Reserved
Reserved
*:
SA0-5 (8 KBx6)
0x0004_C000
SA6-9 (8 KBx4)
0x0000_0000
SA0-5 (8 KBx6)
Flash
304 Kbytes
0x0000_0000
Flash
560 Kbytes
SA6-13 (8 KBx8)
See "S6E1B8 Series Flash Programming Manual" to check details of the Flash memory.
Document Number: 001-99223 Rev.*A
Page 55 of 129
S6E1B8 Series
Peripheral Address Map
Start Address
End Address
Bus
0x4000_0000
0x4000_0FFF
0x4000_1000
0x4000_FFFF
0x4001_0000
0x4001_0FFF
Clock/Reset Control
0x4001_1000
0x4001_1FFF
Hardware Watchdog Timer
0x4001_2000
0x4001_2FFF
0x4001_3000
0x4001_4FFF
AHB
APB0
Peripheral
Flash memory I/F register
Reserved
Software Watchdog Timer
Reserved
0x4001_5000
0x4001_5FFF
Dual-Timer
0x4001_6000
0x4001_FFFF
Reserved
0x4002_0000
0x4002_0FFF
Multi-function Timer unit0
0x4002_1000
0x4002_3FFF
Reserved
0x4002_4000
0x4002_4FFF
PPG
0x4002_5000
0x4002_5FFF
Base Timer
0x4002_6000
0x4002_6FFF
Reserved
0x4002_7000
0x4002_7FFF
A/D Converter
0x4002_8000
0x4002_DFFF
Reserved
0x4002_E000
0x4002_EFFF
Built-in CR trimming
0x4002_F000
0x4002_FFFF
Reserved
0x4003_0000
0x4003_0FFF
External Interrupt Controller
0x4003_1000
0x4003_1FFF
Interrupt Request Batch-Read Function
0x4003_2000
0x4003_2FFF
LCD Controller
0x4003_3000
0x4003_3FFF
0x4003_4000
0x4003_5000
0x4003_6000
0x4003_7000
0x4003_8000
0x4003_4FFF
0x4003_5FFF
0x4003_6FFF
0x4003_7FFF
0x4003_8FFF
HDMI-CEC/ Remote Control Receiver
Low-Voltage Detection / DS mode / Vref Calibration
USB Clock Generator
Reserved
Multi-function Serial Interface
0x4003_9000
0x4003_9FFF
CRC
0x4003_A000
0x4003_AFFF
Watch Counter
0x4003_B000
0x4003_BFFF
Real-time clock
0x4003_C000
0x4003_C0FF
Low-speed CR Prescaler
0x4003_C100
0x4003_C800
0x4003_C900
0x4003_CA00
0x4003_CB00
0x4004_0000
0x4006_0000
0x4006_1000
0x4006_2000
0x4003_C7FF
0x4003_FFFF
0x4003_C9FF
0x4003_CAFF
0x4003_FFFF
0x4005_FFFF
0x4006_0FFF
0x4006_1FFF
0x41FF_FFFF
Peripheral Clock Gating
Reserved
Smart Card Interface
2
I S Clock Generator
Reserved
USB ch.0
Reserved
DSTC
Reserved
Document Number: 001-99223 Rev.*A
APB1
AHB
GPIO
Page 56 of 129
S6E1B8 Series
10. Pin Status in Each CPU State
The terms used for pin status have the following meanings.
INITX=0
This is the period when the INITX pin is the "L" level.
INITX=1
This is the period when the INITX pin is the "H" level.
SPL=0
This is the status that the standby pin level setting bit (SPL) in the Standby Mode Control
Register (STB_CTL) is set to "0".
SPL=1
This is the status that the standby pin level setting bit (SPL) in the Standby Mode Control
Register (STB_CTL) is set to "1".
Input enabled
Indicates that the input function can be used.
Internal input fixed at "0"
This is the status that the input function cannot be used. Internal input is fixed at "L".
Hi-Z
Indicates that the pin drive transistor is disabled and the pin is put in the Hi-Z state.
Setting disabled
Indicates that the setting is disabled.
Maintain previous state
Maintains the state in which a pin was immediately prior to entering the current mode.
If a built-in peripheral function is operating, the output follows the peripheral function.
If the pin is being used as a port, that output is maintained.
Analog input is enabled
Indicates that the analog input is enabled.
Trace output
Indicates that the trace function can be used.
GPIO selected
In Deep standby mode, pins switch to the general-purpose I/O port.
Document Number: 001-99223 Rev.*A
Page 57 of 129
S6E1B8 Series
Pin Status Type
List of Pin Status
A
B
State
when
State in Deep Standby
Return
RTC Mode or Deep
Standby Stop Mode from Deep
Standby
State
Mode
State
State Upon
Power-on State at
Reset or
INITX
Low-Voltag
Input
Function e Detection
Group
State
Upon
Device
Internal
Reset
State in
Run Mode
or Sleep
Mode
Power
Supply
Unstable
-
Power
Supply
Stable
INITX=0
-
Power
Supply
Stable
INITX=1
-
Power
Supply
Stable
INITX=1
-
GPIO
selected
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
Main
crystal
oscillator
input pin/
External
main
clock
input
selected
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
GPIO
selected /
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
Maintain
previous
state
Maintain
previous
state /
When
oscillation
stops*1,
Hi-Z /
Internal
input fixed
at 0
Pull-up /
Input
enabled
Input
enabled
Maintain
previous
state /
When
oscillation
stops*1,
Hi-Z /
Internal
input fixed
at 0
Pull-up /
Input
enabled
Input
enabled
GPIO
selected
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
External
main
clock
input
selected
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
Main
crystal
oscillator
output
pin
C
INITX
input pin
D
Mode
input pin
State in Timer Mode,
RTC Mode, or
Stop Mode
Power Supply Stable
Power Supply Stable
INITX=1
SPL=0
SPL=1
INITX=1
SPL=0
SPL=1
GPIO
Hi-Z /
selected /
Internal
Internal
input fixed
input fixed
at 0
at 0
Maintain
Maintain
Maintain
Maintain
previous
previous
previous
previous
state /
Hi-Z /
state/When state/When state/When
Hi-Z /
Hi-Z /
When
Internal
oscillation oscillation oscillation
input fixed at Internal
Internal
oscillation
1
1
1
stops* ,
stops* ,
stops* ,
0/
input fixed input fixed
stops*1,
Hi-Z /
Hi-Z /
Hi-Z /
at 0
at 0
Input
Hi-Z /
Internal
Internal
Internal
enabled
Internal
input fixed input fixed input fixed
input fixed
at 0
at 0
at 0
at 0
Pull-up /
Pull-up / Pull-up /
Pull-up /
Pull-up /
Pull-up /
Pull-up /
Input
Input
Input
Input
Input
Input
Input
enabled
enabled enabled
enabled
enabled
enabled
enabled
Input
Input
Input
Input
Input
Input
Input
enabled
enabled enabled
enabled
enabled
enabled
enabled
Document Number: 001-99223 Rev.*A
Power
Supply
Stable
INITX=1
GPIO
selected
Page 58 of 129
S6E1B8 Series
State
Upon
Device
Internal
Reset
State in
Run Mode
or Sleep
Mode
Power
Supply
Unstable
-
Power
Supply
Stable
INITX=0
-
Power
Supply
Stable
INITX=1
-
Power
Supply
Stable
INITX=1
-
GPIO
selected
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
Sub
crystal
E oscillator
input
pin /
External
sub clock
input
selected
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
GPIO
selected
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
External
sub clock
input
selected
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
Pin Status Type
State Upon
Power-on State at
Reset or
INITX
Low-Voltag
Input
Function e Detection
Group
F
Hi-Z /
Sub
Hi-Z /
Hi-Z /
Internal
crystal
Internal
input fixed at Internal
oscillator
0/
input fixed input fixed
output
at 0
at 0
Input
pin
enabled
NMIX
selected
Resourc
e other
G than the
above
selected
GPIO
selected
Setting
disabled
Hi-Z
Setting
disabled
Hi-Z /
Input
enabled
Document Number: 001-99223 Rev.*A
Maintain
previous
state
Setting
disabled
Hi-Z /
Input
enabled
Maintain
previous
state
State in Timer Mode,
RTC Mode, or
Stop Mode
State
when
State in Deep Standby
Return
RTC Mode or Deep
Standby Stop Mode from Deep
Standby
State
Mode
State
Power Supply Stable
Power Supply Stable
INITX=1
SPL=0
SPL=1
Hi-Z /
Maintain
Internal
previous
input fixed
state
at 0
INITX=1
SPL=0
SPL=1
Power
Supply
Stable
INITX=1
-
Input
enabled
Input
enabled
Input
enabled
Input
enabled
GPIO
selected
Hi-Z / Input
enabled
GPIO
selected
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
GPIO
selected /
Internal
input fixed
at 0
Maintain
previous
state
Maintain
Maintain
Maintain
previous
previous
previous
state /
state/When state/When
When
oscillation oscillation
oscillation
2
2
stops* ,
stops* ,
stops*2,
Hi-Z /
Hi-Z /
Hi-Z/
Internal
Internal
Internal
input fixed input fixed
input fixed
at 0
at 0
at 0
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
WKUP
input
enabled
Hi-Z /
Internal
input fixed
at 0
Maintain
previous
state /
When
oscillation
stops*2,
Hi-Z/
Internal
input fixed
at 0
Hi-Z /
WKUP
input
enabled
Maintain
previous
state
Maintain
previous
state /
When
oscillation
stops*2,
Hi-Z/
Internal
input fixed
at 0
GPIO
selected
Page 59 of 129
Pin Status Type
S6E1B8 Series
H
State Upon
Power-on State at
Reset or
INITX
Low-Voltag
Input
Function e Detection
Group
State
Upon
Device
Internal
Reset
State in
Run Mode
or Sleep
Mode
Power
Supply
Unstable
-
Power
Supply
Stable
INITX=0
-
Power
Supply
Stable
INITX=1
-
Power
Supply
Stable
INITX=1
-
Hi-Z
Pull-up /
Input
enabled
Pull-up /
Input
enabled
Serial
wire
debug
selected
GPIO
selected
Resourc
e
I selected
GPIO
selected
External
interrupt
enabled
selected
Resourc
J e other
than the
above
selected
GPIO
selected
Analog
input
selected
K
Resourc
e other
than the
above
selected
GPIO
selected
Setting
disabled
Setting
disabled
Setting
disabled
Hi-Z
Hi-Z /
Input
enabled
Hi-Z /
Input
enabled
Setting
disabled
Setting
disabled
Setting
disabled
Hi-Z
Hi-Z
Setting
disabled
Hi-Z /
Input
enabled
Hi-Z /
Input
enabled
State in Timer Mode,
RTC Mode, or
Stop Mode
Power Supply Stable
Power Supply Stable
INITX=1
SPL=0
SPL=1
INITX=1
SPL=0
SPL=1
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Hi-Z /
Hi-Z /
Hi-Z /
Internal
Internal
Internal
Internal
input fixed input fixed input fixed input fixed
at 0 /
at 0 /
at 0 /
at 0 /
Analog
Analog
Analog
Analog
input
input
input
input
enabled enabled
enabled
enabled
Setting
disabled
Document Number: 001-99223 Rev.*A
Setting
disabled
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Power
Supply
Stable
INITX=1
-
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
GPIO
selected /
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0
GPIO
selected /
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
Maintain
previous
state
Maintain
previous
state
State
when
State in Deep Standby
Return
RTC Mode or Deep
Standby Stop Mode from Deep
Standby
State
Mode
State
Hi-Z /
Internal
input fixed
at 0
GPIO
selected /
Internal
input fixed
at 0
GPIO
selected /
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Output
Maintain
previous
state /
Internal
input fixed
at 0
Page 60 of 129
Pin Status Type
S6E1B8 Series
State Upon
Power-on State at
Reset or
INITX
Low-Voltag
Input
Function e Detection
Group
Power
Supply
Unstable
Analog
input
selected
External
interrupt
L enabled
selected
Resourc
e other
than the
above
selected
Hi-Z
State
Upon
Device
Internal
Reset
State in
Run Mode
or Sleep
Mode
State in Timer Mode,
RTC Mode, or
Stop Mode
Power
Power
Power
Supply
Supply
Supply
Power Supply Stable
Stable
Stable
Stable
INITX=0 INITX=1
INITX=1
INITX=1
SPL=0
SPL=1
Hi-Z /
Hi-Z /
Hi-Z /
Hi-Z /
Hi-Z /
Internal
Internal
Internal
Internal
Internal
input fixed input fixed input fixed input fixed input fixed
at 0 /
at 0 /
at 0 /
at 0 /
at 0 /
Analog
Analog
Analog
Analog
Analog
input
input
input
input
input
enabled enabled
enabled
enabled
enabled
Maintain
previous
state
State
when
State in Deep Standby
Return
RTC Mode or Deep
Standby Stop Mode from Deep
Standby
State
Mode
State
INITX=1
SPL=0
SPL=1
Hi-Z /
Hi-Z /
Internal
Internal
input fixed input fixed
at 0 /
at 0 /
Analog
Analog
input
input
enabled
enabled
Power
Supply
Stable
INITX=1
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
GPIO
selected /
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
GPIO
selected /
Internal
input fixed
at 0
Power Supply Stable
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
Maintain
previous
state
Mode
input pin
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
GPIO
selected
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
Maintain
previous
state
Hi-Z / Input
enabled
GPIO
selected
Hi-Z / Input
enabled
GPIO
selected
WKUP
input
enabled
Hi-Z /
WKUP
input
enabled
GPIO
selected
M
WKUP
enabled
External
interrupt
enabled
N selected
Resourc
e other
than
above
selected
GPIO
selected
Setting
disabled
Setting
disabled
Maintain
previous
state
Setting
disabled
Maintain
previous
state
Hi-Z
Hi-Z /
Input
enabled
Document Number: 001-99223 Rev.*A
Hi-Z /
Input
enabled
Hi-Z /
Internal
input fixed
at 0
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
GPIO
selected /
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
GPIO
selected /
Internal
input fixed
at 0
Page 61 of 129
Pin Status Type
S6E1B8 Series
State Upon
Power-on State at
Reset or
INITX
Low-Voltag
Input
Function e Detection
Group
State
Upon
Device
Internal
Reset
State in
Run Mode
or Sleep
Mode
Power
Supply
Unstable
-
Power
Supply
Stable
INITX=0
-
Power
Supply
Stable
INITX=1
-
Setting
disabled
Setting
disabled
Setting
disabled
Power
Supply
Stable
INITX=1
Maintain
previous
state
Setting
disabled
Setting
disabled
Setting
disabled
CEC
enabled
WKUP
enabled
O
P
External
interrupt
enabled
selected
Resourc
e other
than
above
selected
GPIO
selected
Resourc
e
selected
Hi-Z
Hi-Z /
Input
enabled
Hi-Z
Hi-Z /
Input
enabled
Hi-Z /
Input
enabled
GPIO
selected
External
interrupt
enabled
selected
Setting
disabled
Setting
disabled
Setting
disabled
Q USB IO
GPIO
selected
Hi-Z
Hi-Z/Input Hi-Z/Input
enabled enabled
Document Number: 001-99223 Rev.*A
Power Supply Stable
Power Supply Stable
INITX=1
SPL=0
SPL=1
Maintain
Maintain
previous
previous
state
state
INITX=1
SPL=0
SPL=1
Maintain
Maintain
previous
previous
state
state
Hi-Z /
WKUP
WKUP
input
input
enabled
enabled
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Input
enabled
State in Timer Mode,
RTC Mode, or
Stop Mode
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
Maintain
previous
State
Maintain
previous
state
State
when
State in Deep Standby
Return
RTC Mode or Deep
Standby Stop Mode from Deep
Standby
State
Mode
State
GPIO
selected /
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
Power
Supply
Stable
INITX=1
Maintain
previous
state
GPIO
selected /
Internal
input fixed
at 0
Maintain
previous
State
Hi-Z /
Internal
input fixed
at 0
GPIO
selected /
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Maintain
previous
state
Maintain
previous
state
GPIO
selected /
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Hi-Z/Input
enabled
Hi-Z/Input
enabled
Hi-Z/Input
enabled
GPIO
Hi-Z
GPIO
Hi/-Z/Input Hi/-Z/Input
enabled
enabled
Maintain
previous
state
Hi-Z
Page 62 of 129
Pin Status Type
S6E1B8 Series
State Upon
Power-on State at
Reset or
INITX
Low-Voltag
Input
Function e Detection
Group
State
Upon
Device
Internal
Reset
State in
Run Mode
or Sleep
Mode
Power
Supply
Unstable
-
Power
Supply
Stable
INITX=1
-
Power
Supply
Stable
INITX=1
-
WKUP
enabled
R
External
interrupt
enabled
selected
Resourc
e other
than
above
selected
INITX=1
SPL=0
SPL=1
INITX=1
SPL=0
SPL=1
Power
Supply
Stable
INITX=1
-
WKUP input Hi-Z / WKUP
enabled
input enabled
Setting
Setting
Setting
fixed at 0
disabled
disabled
disabled
Maintain
GPIO
previous
selected /
state
Setting
disabled
Resourc
e other
than
above
selected
Hi-Z
GPIO
selected
Power Supply Stable
Hi-Z /
GPIO
selected
S
Power Supply Stable
Internal input
Hi-Z
External
interrupt
enabled
selected
Power
Supply
Stable
INITX=0
-
State in Timer Mode,
RTC Mode, or
Stop Mode
State
when
State in Deep Standby
Return
RTC Mode or Deep
Standby Stop Mode from Deep
Standby
State
Mode
State
Hi-Z /
Hi-Z /
Internal
Internal
input fixed
input fixed
at 0
at 0
Setting
disabled
Document Number: 001-99223 Rev.*A
Maintain
Maintain
Internal input
previous
previous
fixed at 0
state
state
Hi-Z /
Internal input
fixed at 0
Maintain
previous
state
Setting
disabled
Hi-Z /
Hi-Z /
Internal
Internal
input fixed input fixed
at 0
at 0
GPIO
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
Internal input
selected /
fixed at 0
Hi-Z /
Internal input
Output
fixed at 0
Output
maintains
maintains
previous
previous
state /
state /
Internal input
Internal input
fixed at 0
fixed at 0
GPIO
selected /
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
Output
Maintain
previous
state /
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
Output
Maintain
previous
state /
Internal
input fixed
at 0
Page 63 of 129
Pin Status Type
S6E1B8 Series
State Upon
Power-on State at
Reset or
INITX
Low-Voltag
Input
Function e Detection
Group
State
Upon
Device
Internal
Reset
State in
Run Mode
or Sleep
Mode
Power
Supply
Unstable
-
Power
Supply
Stable
INITX=1
-
Power
Supply
Stable
INITX=1
-
Power
Supply
Stable
INITX=0
-
State in Timer Mode,
RTC Mode, or
Stop Mode
Power Supply Stable
Power Supply Stable
INITX=1
SPL=0
SPL=1
INITX=1
SPL=0
SPL=1
Hi-Z /
Internal
input fixed
at 0
WKUP
enabled
External
interrupt
enabled
selected
T
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
Maintain
previous
state
Resourc
e other
than
above
selected
Hi-Z
GPIO
selected
Hi-Z /
Hi-Z /
Internal
Internal
input fixed input fixed
at 0
at 0
Document Number: 001-99223 Rev.*A
State
when
State in Deep Standby
Return
RTC Mode or Deep
Standby Stop Mode from Deep
Standby
State
Mode
State
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
WKUP
input
enabled
GPIO
selected /
Internal
input fixed
at 0
Output
maintains
previous
state /
Internal
input fixed
at 0
Power
Supply
Stable
INITX=1
-
Hi-Z /
WKUP
input
enabled
GPIO
selected /
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
Output
maintains
previous
state /
Internal
input fixed
at 0
Page 64 of 129
Pin Status Type
S6E1B8 Series
State Upon
Power-on State at
Reset or
INITX
Low-Voltag
Input
Function e Detection
Group
State
Upon
Device
Internal
Reset
State in
Run Mode
or Sleep
Mode
Power
Supply
Unstable
-
Power
Supply
Stable
INITX=0
-
Power
Supply
Stable
INITX=1
-
Power
Supply
Stable
INITX=1
-
Setting
disabled
Setting
disabled
Setting
disabled
CEC
enabled
WKUP
enabled
U
External
interrupt
enabled
selected
Resourc
e other
than
above
selected
V
External
interrupt
enabled
selected
Resourc
e other
than
above
selected
GPIO
selected
Power Supply Stable
Power Supply Stable
INITX=1
SPL=0
SPL=1
Maintain
previous
state
INITX=1
SPL=0
SPL=1
Maintain
Maintain
previous
previous
state
state
Hi-Z /
Internal
input fixed
at 0
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Hi-Z
Hi-Z /
Hi-Z /
Internal
Internal
input fixed input fixed
at 0
at 0
Hi-Z /
Internal
input fixed
at 0
Hi-Z
Hi-Z /
Hi-Z /
Hi-Z /
Hi-Z /
Internal
Internal
Internal
Internal
input fixed input fixed input fixed input fixed
at 0 /
at 0 /
at 0 /
at 0 /
Analog
Analog
Analog
Analog
input
input
input
input
enabled enabled
enabled
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
GPIO
selected
Analog
input
selected
State in Timer Mode,
RTC Mode, or
Stop Mode
Setting
disabled
Setting
disabled
Document Number: 001-99223 Rev.*A
Setting
disabled
Maintain
previous
state
State
when
State in Deep Standby
Return
RTC Mode or Deep
Standby Stop Mode from Deep
Standby
State
Mode
State
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
WKUP
input
enabled
GPIO
selected /
Internal
input fixed
at 0
Output
maintains
previous
state /
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
GPIO
selected /
Internal
input fixed
at 0
Hi-Z /
WKUP
input
enabled
Hi-Z /
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0
Power
Supply
Stable
INITX=1
Maintain
previous
state
GPIO
selected /
Internal
input fixed
at 0
Output
maintains
previous
state /
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
GPIO
selected /
Internal
input fixed
at 0
Page 65 of 129
Pin Status Type
S6E1B8 Series
State Upon
Power-on State at
Reset or
INITX
Low-Voltag
Input
Function e Detection
Group
Power
Supply
Unstable
-
Analog
input
selected
W
State in
Run Mode
or Sleep
Mode
State in Timer Mode,
RTC Mode, or
Stop Mode
Power
Power
Power
Supply
Supply
Supply
Power Supply Stable
Stable
Stable
Stable
INITX=0 INITX=1
INITX=1
INITX=1
SPL=0
SPL=1
Hi-Z /
Hi-Z /
Hi-Z /
Hi-Z /
Hi-Z /
Internal
Internal
Internal
Internal
Internal
input fixed input fixed input fixed input fixed input fixed
at 0 /
at 0 /
at 0 /
at 0 /
at 0 /
Analog
Analog
Analog
Analog
Analog
input
input
input
input
input
enabled enabled
enabled
enabled
enabled
Hi-Z /
Internal
input fixed
at 0
WKUP
enabled
External
interrupt
enabled
selected
Resourc
e other
than
above
selected
GPIO
selected
External
interrupt
enabled
selected
X
Hi-Z
State
Upon
Device
Internal
Reset
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
Setting
disabled
Resourc
e other
than
above
selected
Setting
disabled
Maintain
previous
state
Setting
disabled
Hi-Z /
Hi-Z /
Internal
Internal
input fixed input fixed
at 0
at 0
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
State
when
State in Deep Standby
Return
RTC Mode or Deep
Standby Stop Mode from Deep
Standby
State
Mode
State
Power Supply Stable
INITX=1
SPL=0
SPL=1
Hi-Z /
Hi-Z /
Internal
Internal
input fixed input fixed
at 0 /
at 0 /
Analog
Analog
input
input
enabled
enabled
WKUP
input
enabled
GPIO
selected /
Internal
input fixed
at 0
GPIO
selected /
Internal
input fixed
at 0
Output
Maintain
previous
GPIO
state /
selected
Internal
input fixed
at 0
*1: Oscillation stops in Sub timer mode, Low-speed CR timer mode, Stop mode, RTC mode.
Hi-Z
Power
Supply
Stable
INITX=1
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
WKUP
input
enabled
Hi-Z /
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
GPIO
selected /
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
*2: Oscillation stops in Stop mode.
Document Number: 001-99223 Rev.*A
Page 66 of 129
S6E1B8 Series
11. Electrical Characteristics
11.1 Absolute Maximum Ratings
Parameter
Symbol
1, 2
Power supply voltage* *
1, 3
Analog power supply voltage* *
1, 3
Analog reference voltage* *
1
Input voltage*
VCC
AVCC
AVRH
VI
1
Analog pin input voltage*
1
Output voltage*
4
L level maximum output current*
5
L level average output current*
L level total maximum output current
6
L level total average output current*
4
H level maximum output current*
Min
VSS - 0.5
VSS - 0.5
VSS - 0.5
VSS - 0.5
VSS - 0.5
VIA
VSS - 0.5
VO
VSS - 0.5
IOL
-
IOLAV
∑IOL
∑IOLAV
-
IOH
-
5
Rating
H level average output current*
IOHAV
H level total maximum output current
∑IOH
6
H level total average output current*
∑IOHAV
Power consumption
PD
Storage temperature
TSTG
*1: These parameters are based on the condition that VSS=AVSS=0 V.
- 55
Max
VSS + 4.6
VSS + 4.6
VSS + 4.6
VCC + 0.5
(≤ 4.6 V)
VSS + 6.5
VCC + 0.5
(≤ 4.6 V)
VCC + 0.5
(≤ 4.6 V)
10
39
4
100
50
- 10
- 39
-4
- 100
- 50
250
+ 150
Unit
Remarks
V
V
V
V
V
5 V tolerant
V
V
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mW
°C
P0B / P0C
P0B / P0C
*2: VCC must not drop below VSS - 0.5 V.
*3: Ensure that the voltage does not to exceed VCC + 0.5 V at power-on.
*4: The maximum output current is the peak value for a single pin.
*5: The average output is the average current for a single pin over a period of 100 ms.
*6: The total average output current is the average current for all pins over a period of 100 ms.
*7: When P0C/UDP0 and P0B/UDM0 pins are used as GPIO (P0C, P0B).
*8: When P0C/UDP0 and P0B/UDM0 pins are used as USB (UDP0, UDM0).
<WARNING>
Semiconductor devices can be permanently damaged by application of stress (voltage, current, temperature, etc.) in excess of
absolute maximum ratings. Do not exceed these ratings.
−
Document Number: 001-99223 Rev.*A
Page 67 of 129
S6E1B8 Series
11.2 Recommended Operating Conditions
(VSS=AVSS=0.0 V)
Parameter
Symbol
Conditions
Power supply voltage
VCC
-
LCD input voltage
VVV4
-
Min
5
1.65 *
2.2
3.0
2.2
2.2
-
0.5
Fin
-
-
AVCC
-
Cf,CVV1,
CVV2,CVV3,
CVV4
LCD External Capacitor *6
Sub Oscillation frequency
*7
Analog power supply voltage
Analog reference voltage
Smoothing capacitor
Operating temperature
*1: When LCD Controller is not used.
AVRH
-
AVRL
CS
TA
-
Value
Max
3.6
3.6
3.6
VCC
4.7
Unit
Remarks
V
V
V
V
V
*1
*2
*3
No booster used
Booster is used
1.3
μF
Booster is used
-
kHz
1.65
3.6
V
Typical is
32.768 kHz
AVCC=VCC
2.7
AVCC
V
AVCC ≥ 2.7 V
AVCC
AVSS
1
- 40
AVCC
AVSS
10
+ 105
V
V
μF
°C
AVCC < 2.7 V
4
For regulator*
*2: When LCD Controller is used.
*3: When P0C/UDP0 and P0B/UDM0 pins are used as USB (UDP0, UDM0).
*4: See "C Pin" in "7. Handling Devices" for the connection of the smoothing capacitor.
*5: In between less than the minimum power supply voltage reset / interrupt detection voltage or more, instruction execution and low
voltage detection function by built-in High-speed CR (including Main PLL is used) or built-in Low-speed CR is possible to operate
only.
*6: LCD external capacitor between VVx to VSS, and between C0 and C1.
*7: If a Booster is used, Sub OSC should provide operation clock at typically 32.768 kHz.
<WARNING>
1. The recommended operating conditions are required in order to ensure the normal operation of the semiconductor device. All of
the device's electrical characteristics are warranted when the device is operated within these ranges.
2.
Always use semiconductor devices within their recommended operating condition ranges. Operation outside these ranges may
adversely affect reliability and could result in device failure.
3.
No warranty is made with respect to uses, operating conditions, or combinations not represented on the data sheet.
4.
Users considering application outside the listed conditions are advised to contact their representatives beforehand.
Document Number: 001-99223 Rev.*A
Page 68 of 129
S6E1B8 Series
11.3 DC Characteristics
11.3.1 Current Rating
Symbol
4 MHz external clock input, PLL ON*8
NOP code executed
Built-in high speed CR stopped
All peripheral clock stopped by CKENx
Run mode,
code executed
from Flash
*8
4 MHz external clock input, PLL ON
Benchmark code executed
Built-in high speed CR stopped
PCLK1 stopped
*8
4 MHz crystal oscillation, PLL ON
NOP code executed
Built-in high speed CR stopped
All peripheral clock stopped by CKENx
ICC
(VCC)
Run mode,
code executed
from RAM
Run mode,
code executed
from Flash
Run mode,
code executed
from Flash
ICCS
(VCC)
Sleep
operation
Value
HCLK
Conditions
(Pin Name)
4 MHz external clock input, PLL ON*8
NOP code executed
Built-in high speed CR stopped
All peripheral clock stopped by CKENx
4 MHz external clock input, PLL ON
NOP code executed
Built-in high speed CR stopped
PCLK1 stopped
Built-in high speed CR*5
NOP code executed
All peripheral clock stopped by CKENx
32 kHz crystal oscillation
NOP code executed
All peripheral clock stopped by CKENx
Built-in low speed CR
NOP code executed
All peripheral clock stopped by CKENx
Frequency*4
4 MHz
Typ*1
Max*2
0.7
1.9
8 MHz
1.5
2.7
20 MHz
3.1
4.4
40 MHz
5.5
7.2
4 MHz
0.65
1.8
8 MHz
1.4
2.6
20 MHz
2.9
4.2
40 MHz
5.2
6.8
4 MHz
0.9
2.1
8 MHz
1.6
2.9
20 MHz
3.2
4.7
40 MHz
5.7
7.4
Unit
Remarks
mA
*3
mA
*3
mA
*3
mA
*3
4 MHz
0.5
1.3
8 MHz
1.1
2.0
20 MHz
2.2
3.1
40 MHz
4.2
5.1
40 MHz
2.6
3.8
mA
*3,*6,*7
4 MHz
0.9
2.2
mA
*3
32 kHz
96
1250
μA
*3
100 kHz
120
1260
μA
*3
mA
*3
4 MHz
0.5
1.3
4 MHz external clock input, PLL ON*8
8 MHz
0.9
1.8
All peripheral clock stopped by CKENx
20 MHz
1.7
2.8
40 MHz
3
4.3
4 MHz
0.6
1.7
mA
*3
32 kHz
94
960
μA
*3
100 kHz
105
980
μA
*3
*5
Built-in high speed CR
All peripheral clock stopped by CKENx
32 kHz crystal oscillation
All peripheral clock stopped by CKENx
Built-in low speed CR
All peripheral clock stopped by CKENx
*1 : TA=+25°C,VCC=3.3 V
*2 : TA=+105°C,VCC=3.6 V
*3 : All ports are fixed
*4 : PCLK0 is set to divided rate 8
*5 : The frequency is set to 4 MHz by trimming
*6 : Flash sync down is set to FRWTR.RWT=11 and FSYNDN.SD=1111
*7 : VCC=1.65 V
*8 : When HCLK=4 MHz, PLL OFF
Document Number: 001-99223 Rev.*A
Page 69 of 129
S6E1B8 Series
Parameter
Symbol
(Pin Name)
ICCH
(VCC)
Power
supply
current
ICCT
(VCC)
ICCR
(VCC)
Conditions
Stop mode
Sub timer mode
RTC mode
*1: All ports are fixed. LVD off. Flash off.
Document Number: 001-99223 Rev.*A
Typ
Value
Max
Unit
Remarks
TA=25°C
VCC=3.3 V
8.5
35
μA
*1
TA=25°C
VCC=1.65 V
8
34
μA
*1
TA=105°C
VCC=3.6 V
-
722
μA
*1
13
40
μA
*1
12.5
39
μA
*1
-
729
μA
*1
10
37
μA
*1
9.5
36
μA
*1
-
723
μA
*1
TA=25°C
VCC=3.3 V
32 kHz Crystal
oscillation
TA=25°C
VCC=1.65 V
32 kHz Crystal
oscillation
TA=105°C
VCC=3.6 V
32 kHz Crystal
oscillation
TA=25°C
VCC=3.3 V
32 kHz Crystal
oscillation
TA=25°C
VCC=1.65 V
32 kHz Crystal
oscillation
TA=105°C
VCC=3.6 V
32 kHz Crystal
oscillation
Page 70 of 129
S6E1B8 Series
Parameter
Symbol
(Pin
Name)
RAM off
ICCHD
(VCC)
Deep standby
Stop mode
RAM on
Power
supply
current
RAM off
ICCRD
(VCC)
Value
Conditions
Deep standby
RTC mode
RAM on
*1: All ports are fixed. LVD off.
Document Number: 001-99223 Rev.*A
TA=25°C
VCC=3.3 V
TA=25°C
VCC=1.65 V
TA=105°C
VCC=3.6 V
TA=25°C
VCC=3.3 V
TA=25°C
VCC=1.65 V
TA=105°C
VCC=3.6 V
TA=25°C
VCC=3.3 V
TA=25°C
VCC=1.65 V
TA=105°C
VCC=3.6 V
TA=25°C
VCC=3.3 V
TA=25°C
VCC=1.65 V
TA=105°C
VCC=3.6 V
Unit
Remarks
Typ
Max
0.95
2.8
μA
*1
0.94
2.7
μA
*1
-
232
μA
*1
1.15
11.5
μA
*1
1.1
11.4
μA
*1
-
247
μA
*1
1.85
3.41
μA
*1
1.8
3.4
μA
*1
-
233
μA
*1
2.05
12.1
μA
*1
2
12.1
μA
*1
-
248
μA
*1
Page 71 of 129
S6E1B8 Series
Parameter
Symbol
(Pin Name)
RTC
operation
Power
supply
current
Typ
Value
Max
0.9
1.55
μA
*1
0.8
1.55
μA
*1
-
3.73
μA
*1
TA=25°C
VCC=3.0V
0.05
0.64
μA
*1
TA=25°C
VCC=1.65 V
0.02
0.28
μA
*1
-
1.24
μA
*1
Conditions
ICCVBAT
(VBAT)
RTC stop
TA=25°C
VCC=3.0V
32 kHz Crystal
oscillation
TA=25°C
VCC=1.65 V
32 kHz Crystal
oscillation
TA=105°C
VCC=3.6V
32 kHz Crystal
oscillation
TA=105°C
VCC=3.6V
Unit
Remarks
*1: All ports are fixed.
Document Number: 001-99223 Rev.*A
Page 72 of 129
S6E1B8 Series
LVD Current
Parameter
Low-Voltage
detection circuit
(LVD) power
supply current
(VCC=1.65 V to 3.6 V, VSS=AVSS=0 V, TA=- 40°C to +105°C)
Symbol
ICCLVD
Pin Name
VCC
Conditions
Flash
memory
write/erase
current
Power supply
current
Reference power
supply current
(AVRH)
Symbol
Pin Name
Conditions
ICCFLASH
VCC
At Write/Erase
Unit
Remarks
0.13
0.3
μA
For occurrence of reset
0.13
0.3
μA
For occurrence of interrupt
Typ
Value
9.5
Max
11.2
Unit
Remarks
mA
(VCC=1.65 V to 3.6 V, VSS=AVSS=0 V, TA=- 40°C to +105°C)
Symbol
Pin Name
ICCAD
AVCC
ICCAVRH
AVRH
Document Number: 001-99223 Rev.*A
Max
(VCC=1.65 V to 3.6 V, VSS=AVSS=0 V, TA=- 40°C to +105°C)
A/D converter Current
Parameter
Value
At operation
Flash Memory Current
Parameter
Typ
Conditions
Value
Max
0.6
Unit
At operation
Typ
0.33
At stop
0.1
10
μA
At operation
0.72
1.29
mA
At stop
0.1
1.7
μA
Remarks
mA
AVRH=3.6 V
Page 73 of 129
S6E1B8 Series
Peripheral Current Dissipation
Clock
System
Peripheral
Conditions
GPIO
At all ports
operation
0.02
0.04
0.11
0.22
DSTC
At 2ch
operation
0.07
0.15
0.37
0.74
Base timer
At 4ch
operation
0.02
0.04
0.08
0.16
Multi-functional
timer/PPG
At 1 unit/4ch
operation
0.06
0.11
0.28
0.55
ADC
At 1 unit
operation
0.02
0.04
010
0.20
Multi-function serial
At 1ch
operation
0.03
0.06
0.16
0.31
HCLK
PCLK1
(VCC= 3.3 V, TA=25°C)
Frequency (MHz)
8
20
Document Number: 001-99223 Rev.*A
4
40
Unit
Remarks
mA
mA
Page 74 of 129
S6E1B8 Series
11.3.2 Pin Characteristics
Parameter
H level input
voltage
(hysteresis
input)
L level input
voltage
(hysteresis
input)
H level
output voltage
L level
output voltage
(VCC =AVCC=1.65 V to 3.6 V, VSS=AVSS=0 V, TA=- 40°C to +105°C)
Symbol
VIHS
VILS
Value
Typ
Max
-
VCC +0.3
V
VCC × 0.8
VCC × 0.7
-
VSS +5.5
V
VSS - 0.3
-
Pin Name
Conditions
CMOS
hysteresis
input pin, MD0,
MD1
5 V tolerant
input pin
CMOS
hysteresis
input pin, MD0,
MD1
5 V tolerant
input pin
VCC ≥ 2.7 V
Min
VCC × 0.8
VCC < 2.7 V
VCC × 0.7
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
4 mA type
VOH
The pin
doubled as
USB I/O
4 mA type
VOL
The pin
doubled as
USB I/O
-
Input leak current
IIL
CEC0_0,
CEC1_0,
CEC1_1
Pull-up resistance
value
RPU
Pull-up pin
Input capacitance
CIN
Other than
VCC, VSS,
AVCC, AVSS,
AVRH
Document Number: 001-99223 Rev.*A
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V,
IOH = - 4 mA
VCC < 2.7 V,
IOH = - 2 mA
VSS - 0.3
VCC - 0.5
VCC - 0.45
Unit
Remarks
VCC × 0.2
VCC × 0.3
V
-
VCC × 0.2
VCC × 0.3
V
-
VCC
V
-
VCC - 0.4
-
VCC
V
VCC ≥ 2.7 V,
IOL 4 mA
VCC < 2.7 V,
IOL=2 mA
VSS
-
0.4
V
-
VSS
-
0.4
V
VCC = AVCC =
AVRH = VSS =
AVSS = AVRL =
0.0V
VCC ≥ 2.7 V
VCC < 2.7 V
-5
-
+5
μA
-
-
+1.8
μA
21
-
33
-
66
134
kΩ
-
-
5
15
pF
Page 75 of 129
S6E1B8 Series
11.3.3 LCD Characteristic
11.3.3.1 LCD Characteristic Without Booster
(VCC =AVCC=1.65 V to 3.6 V, VSS=AVSS=0 V, TA=- 40°C to +105°C)
Parameter
VV0 to VV3
output voltage
(1/4 bias)
VV0 to VV3
output voltage
(1/3 bias)
VV0 to VV3
output voltage
(1/2 bias)
VV4 Active
current (1/4 bias)
VV4 Active
current (1/3 bias)
VV4 Active
current (1/2 bias)
VV4 static
current
VV0 output
voltage in using
external resistor
Symb
ol
Pin
Name
VVV0
VV0
VVV1
VV1
VVV2
VV2
VVV3
VV3
VVV0
VV0
VVV1
VV1
VVV2
VV2
VVV3
VV3
VVV0
VV0
VVV1
VV1
VVV2
VV2
VVV3
VV3
IR100K
VV4
IR10K
VV4
IR100K
VV4
IR10K
VV4
IR100K
VV4
IR10K
VV4
IOFF_VV4
VV4
VVV0E
VV0
Document Number: 001-99223 Rev.*A
Conditions
Min
0
When using internal
dividing register
When using internal
dividing register
When using internal
dividing register
When using 100 kΩ
internal dividing
resistor
When using 10 kΩ
internal dividing
resistor
When using 100 kΩ
internal dividing
resistor
When using 10 kΩ
internal dividing
resistor
When using 100 kΩ
internal dividing
resistor
When using 10 kΩ
internal dividing
resistor
VVV4 x 1/4
-10%
VVV4 x 1/2
-10%
VVV4 x 3/4
-10%
0
VVV4 x 1/3
-10%
VVV4 x 2/3
-10%
VVV4 x 2/3
-10%
0
VVV4 x 1/2
-10%
VVV4 x 1/2
-10%
VVV4 x 1/2
-10%
Value
Typ
-
Max
Unit
Remarks
VVV4 x 5%
VVV4 x 1/4
+10%
VVV4 x 1/2
+ 10%
VVV4 x 3/4
+ 10%
VVV4 x 5%
VVV4 x 1/3
+ 10%
VVV4 x 2/3
+ 10%
VVV4 x 2/3
+ 10%
VVV4 x 5%
VVV4 x 1/2
+ 10%
VVV4 x 1/2
+ 10%
VVV4 x 1/2
+ 10%
V
V
V
-
10
16
µA
-
80
100
µA
-
12
20
µA
-
105
125
µA
-
18
30
µA
-
160
180
µA
When LCD stops
-
0.5
1
µA
IOL=1 mA
-
-
0.66
V
Page 76 of 129
S6E1B8 Series
11.3.3.2
LCD Characteristic With Booster
Recommended LCD Operation Conditions With Booster
(VCC =AVCC=1.65 V to 3.6 V, VSS=AVSS=0 V, TA=- 40°C to +105°C)
Parameter
Symbol
Pin
Name
Value
Typ
Max
Voltage correlation
VCC-VV
1
Min
VCC,VV1
0.35
-
Vtole
VV1,VV2
,VV3,VV
4,C0,C1
0
fIN
-
External Capacitor
Cf,CVV1,
CVV2,CVV3
,
CVV4
LCD capacitor
Frame period
Unit
Remarks
-
V
VCC-VV1 must be larger than
0.35 V
-
5.5
V
-
32.76
8
-
kHz
VV1,VV2
,VV3,VV
4,C0,C1
0.5
1
1.3
µF
CLCD/1COM
-
-
1.25
8
µF
tFRAME
-
1/150
-
1/30
s
External input tolerant
voltage
Operating frequency
Crystal oscillator
CHIP
VV4
C1
Cf
VV3
1uF
C0
X0A
32.768kHz
VV2
VV1
VV0
X1A
CVV1
CVV2
CVV3
CVV4
1uF
1uF
1uF
1uF
LCD Booster 1/4 mode （BIAS[1:0]=2'b10)
Document Number: 001-99223 Rev.*A
Page 77 of 129
S6E1B8 Series
CHIP
CHIP
VV4
VV4
C1
Cf
C1
Cf
VV3
1uF
VV3
1uF
C0
VV2
C0
VV2
VV1
X0A
VV1
CVV1
32.768kHz
VV0
X1A
1uF
CVV2
1uF
X0A
CVV4
1uF
VV0
X1A
LCD Booster 1/3 mode （BIAS[1:0]=2'b01)
CVV4
CVV1
32.768kHz
1uF
1uF
LCD Booster 1/2 mode （BIAS[1:0]=2'b00)
DC Electrical Specifications of Internal reference output voltage setting
(VCC =AVCC=1.65 V to 3.6 V, VSS=AVSS=0 V, TA=- 40°C to +105°C)
Parameter
Internal reference
output voltage
setting
Symbol
VV1A
Conditions
Pin
Name TRC[1:0] *1 TRF[3:0] *1
00
1010
00
1011
00
1100
00
1101
00
1110
01
0111
01
1000
01
1001
01
1010
01
1011
VV1
01
1100
01
1101
01
1110
10
0101
10
1100
10
1101
10
1110
11
0010
11
0011
Document Number: 001-99223 Rev.*A
Min
0.89
0.94
0.99
1.03
1.07
1.11
1.16
1.20
1.25
1.30
1.34
1.39
1.44
1.46
1.79
1.84
1.89
1.85
1.90
Value
Typ
1.00
1.05
1.10
1.15
1.20
1.25
1.30
1.35
1.40
1.45
1.50
1.55
1.60
1.65
2.00
2.05
2.10
2.15
2.20
Max
1.11
1.16
1.21
1.27
1.38
1.38
1.44
1.49
1.55
1.60
1.65
1.71
1.76
1.83
2.21
2.26
2.32
2.39
2.44
Unit
Remarks
V
BIAS[1:0]=10
Other BIAS[1:0]setting is
inhibited
V
BIAS[1:0]=01
Other BIAS[1:0]setting is
inhibited
V
BIAS[1:0]=00
Other BIAS[1:0]setting is
inhibited
*4
*3
*2
Page 78 of 129
S6E1B8 Series
Parameter
Internal reference
output voltage
setting
Charge Pump
output voltage
Symbol
Pin
Name
VV1A
VV1
V2
VV2
V3
VV3
V4
VV4
V2
VV2
V3
VV3
V4
VV4
V2
VV2
V3
VV3
V4
VV4
Conditions
TRC[1:0] TRF[3:0]
11
0100
Value
Typ Max
Min
1.96
2.25
2.49
Unit
Remarks
V
BIAS[1:0]=00
Other BIAS[1:0]setting is inhibited
11
0101
2.01
2.30
2.55
11
0110
2.06
2.35
2.60
11
0111
2.11
2.40
2.65
11
1000
2.17
2.45
2.75
2.2
2.3
2.4
V
3.3
3.45
3.6
V
VV1=1.15 V
BIAS1=1
*4
BIAS0=0
VV1=1.5 V
BIAS1=0
*3
BIAS0=1
4.4
4.6
4.8
V
2.9
3.0
3.1
V
=VV2
4.3
VV1=2.25 V
BIAS1=0
*2
BIAS0=0
4.3
4.5
V
4.7
V
=VV1
V
4.7
VV1=1.15[v]
VV1<(VCC-0.35)[V]
V
=VV1
4.5
*1
VV1<(VCC-0.35)[V]
V
*1: Other setting combinations are inhibited
*2: Charge pump 1/2 mode
*3: Charge pump 1/3 mode
*4: Charge pump 1/4 mode
Transient Electrical Specifications
Parameter
Startup time
(VCC =AVCC=1.65 V to 3.6 V, VSS=AVSS=0 V, TA=- 40°C to +105°C)
Symbol
Pin
Name
Min
Value
Typ
Max
tST
VV4
-
-
500
Document Number: 001-99223 Rev.*A
Unit
Remarks
mS
When BSTPD change from 1 to 0
Page 79 of 129
S6E1B8 Series
11.4 AC Characteristics
11.4.1 Main Clock Input Characteristics
Parameter
Symbol
Input frequency
Pin Name
fCH
X0,
X1
(VCC=AVCC=1.65 V to 3.6 V, VSS=AVSS=0 V, TA=- 40°C to +105°C)
Conditions
Value
Unit
Remarks
Min
Max
VCC ≥ 2.7 V
VCC < 2.7 V
4
4
48
20
MHz
When the crystal oscillator
is connected
-
4
48
MHz
When the external
clock is used
-
20.83
250
ns
PWH/tCYLH,
PWL/tCYLH
45
55
%
-
-
5
ns
Input clock pulse width
-
Input clock rising time
and falling time
tCF,
tCR
fCM
-
-
-
40.8
MHz
When the external
clock is used
When the external
clock is used
When the external
clock is used
Master clock
fCC
fCP0
fCP1
-
-
-
40.8
40.8
40.8
MHz
MHz
MHz
Base clock (HCLK/FCLK)
2
APB0 bus clock*
2
APB1 bus clock*
Input clock cycle
tCYLH
Internal operating
*1
clock frequency
Base clock (HCLK/FCLK)
tCYCC
24.5
ns
2
APB0 bus clock*
tCYCP0
24.5
ns
2
APB1 bus clock*
tCYCP1
24.5
ns
*1: For details of each internal operating clock, refer to "Chapter: Clock" in "FM0+ Family Peripheral Manual".
Internal operating
*1
clock cycle time
*2: For details of the APB bus to which a peripheral is connected, see "8. Block Diagram".
tCYLH
X0
0.8 × Vcc
0.8 × Vcc
0.2 × Vcc
PWH
PWL
tCF
Document Number: 001-99223 Rev.*A
0.8 × Vcc
0.2 × Vcc
tCR
Page 80 of 129
S6E1B8 Series
11.4.2 Sub Clock Input Characteristics
Parameter
Input frequency
Input clock cycle
Symbol
(VCC=AVCC=1.65 V to 3.6 V, VSS=AVSS=0 V, TA=- 40°C to +105°C)
Pin Name
fCL
tCYLL
X0A,
X1A
Conditions
Value
Unit
Min
Typ
Max
-
-
32.768
-
kHz
-
32
-
100
kHz
-
10
-
31.25
μs
55
%
Input clock pulse
PWH/tCYLL,
45
width
PWL/tCYLL
*: See "Sub crystal oscillator" in "7. Handling Devices" for the crystal oscillator used.
Remarks
When the crystal
oscillator is
connected*
When the external
clock is used
When the external
clock is used
When the external
clock is used
tCYLL
0.8 × Vcc
0.8 × Vcc
0.2 × Vcc
X0A
PWH
Document Number: 001-99223 Rev.*A
0.8 × Vcc
0.2 × Vcc
PWL
Page 81 of 129
S6E1B8 Series
11.4.3 Built-in CR Oscillation Characteristics
Built-in High-Speed CR
Parameter
(VCC=AVCC=1.65 V to 3.6 V, VSS =AVSS=0 V, TA=- 40°C to +105°C)
Symbol
Value
Conditions
TA = -20°C to +85°C
Min
Typ
Max
3.96
4
4.04
Unit
Remarks
During trimming
Clock frequency
Frequency
stabilization time
fCRH
tCRWT
TA = -40°C to +105°C
3.92
4
4.08
TA = - 40°C to +105°C
2.6
4
5.2
-
-
-
*1
MHz
Not during trimming
30
μs
300
μs
*1: In the case of using the values in CR trimming area of Flash memory at shipment for frequency
trimming/temperature trimming.
*2
If TRT is changed.
*2
*2: This is time from the trim value setting to stable of the frequency of the High-speed CR clock.
After setting the trim value, the period when the frequency stability time passes can use the High-speed CR clock as a source
clock.
Built-in Low-Speed CR
Parameter
Clock frequency
(VCC=AVCC=1.65 V to 3.6 V, VSS=AVSS=0 V, TA=- 40°C to +105°C)
Symbol
Conditions
fCRL
-
Document Number: 001-99223 Rev.*A
Value
Min
Typ
Max
50
100
150
Unit
Remarks
kHz
Page 82 of 129
S6E1B8 Series
11.4.4 Operating Conditions of Main PLL
(In the Case of Using the Main Clock as the Input Clock of the PLL)
(VCC=AVCC=1.65 V to 3.6 V, VSS=AVSS=0 V, TA=- 40°C to +105°C)
Parameter
Symbol
Value
Unit
Min
Typ
Max
100
-
-
μs
PLL input clock frequency
fPLLI
4
PLL multiple rate
5
PLL macro oscillation clock frequency
fPLLO
75
2
Main PLL clock frequency*
fCLKPLL
3
USB clock frequency*
fCLKSPLL
*1: The wait time is the time it takes for PLL oscillation to stabilize.
-
16
37
150
40.8
48
MHz
multiple
MHz
MHz
MHz
1
PLL oscillation stabilization wait time* (LOCK
UP time)
tLOCK
Remarks
*2: For details of the main PLL clock (CLKPLL), refer to "Chapter: Clock" in "FM0+ Family Peripheral Manual".
*3: For more information about USB clock, see "Chapter: USB Clock Generation" in "FM0+ Family Peripheral Manual
Communication Macro Part”.
11.4.5 Operating Conditions of Main PLL
(In the Case of Using the Built-in High-Speed CR Clock as the Input Clock of the Main PLL)
(VCC=AVCC=1.65 V to 3.6 V, VSS=AVSS=0 V, TA=- 40°C to +105°C)
Parameter
Symbol
Value
Unit
Min
Typ
Max
100
-
-
μs
PLL input clock frequency
fPLLI
3.8
PLL multiple rate
19
PLL macro oscillation clock frequency
fPLLO
72
2
Main PLL clock frequency*
fCLKPLL
*1: The wait time is the time it takes for PLL oscillation to stabilize.
4
-
4.2
35
150
40.8
MHz
multiple
MHz
MHz
1
PLL oscillation stabilization wait time* (LOCK
UP time)
tLOCK
Remarks
*2: For details of the main PLL clock (CLKPLL), refer to "Chapter: Clock" in "FM0+ Family Peripheral Manual".
Note:
For the main PLL source clock, input the high-speed CR clock (CLKHC) whose frequency has been trimmed.
When setting PLL multiple rate, please take the accuracy of the built-in High-speed CR clock into account and prevent the
master clock from exceeding the maximum frequency.
−
Main PLL connection
Main clock (CLKMO)
High-speed CR clock (CLKHC)
PLL input
clock
K
divider
Main
PLL
PLL macro
oscillation clock
M
divider
Main PLL
clock
(CLKPLL)
N
divider
Document Number: 001-99223 Rev.*A
Page 83 of 129
S6E1B8 Series
USB PLL connection
PLL input
clock
K
divider
Main clock (CLKMO)
PLL macro
oscillation clock
M
divider
USB PLL
USB
clock
N
divider
11.4.6 Reset Input Characteristics
Parameter
(VCC =AVCC=1.65 V to 3.6 V, VSS=AVSS=0 V, TA=- 40°C to +105°C)
Symbol
Pin Name
Conditions
tINITX
INITX
-
Reset input time
11.4.7 Power-on Reset Timing
Parameter
Value
Min
Max
500
-
Unit
Remarks
ns
(VCC=AVCC=1.65 V to 3.6 V, VSS=AVSS=0 V, TA=- 40°C to +105°C)
Symbol
Power supply rising time
tVCCR
Power supply shut down time
Time until releasing
Power-on reset
tOFF
Pin Name
Value
Max
0
-
ms
1
-
ms
0.43
3.4
ms
VCC
tPRT
Unit
Min
Remarks
VCC < 0.2V
VCC_minimum
VDH_minimum
VCC
0.2V
0.2V
tVCCR
tOFF
tPRT
Internal reset
Reset active
CPU Operation
0.2V
Release
start
Glossary
VCC_minimum : Minimum VCC of recommended operating conditions.
VDH_minimum : Minimum detection voltage of Low-Voltage detection reset.
See "11.7 Low-Voltage Detection Characteristics".
Document Number: 001-99223 Rev.*A
Page 84 of 129
S6E1B8 Series
11.4.8 Base Timer Input Timing
Timer Input Timing
Parameter
Input pulse width
(VCC=AVCC=1.65 V to 3.6 V, VSS=AVSS=0 V, TA=- 40°C to +105°C)
Symbol
Pin Name
Conditions
tTIWH, tTIWL
TIOAn/TIOBn
(when using as
ECK, TIN)
-
Min
Value
2 tCYCP
Max
-
Unit
Remarks
ns
tTIWL
tTIWH
ECK
VIHS
VIHS
TIN
Trigger Input Timing
Parameter
Input pulse width
VILS
VILS
(VCC=AVCC=1.65 V to 3.6 V, VSS=AVSS=0 V, TA=- 40°C to +105°C)
Symbol
Pin Name
Conditions
tTRGH, tTRGL
TIOAn/TIOBn
(when using as
TGIN)
-
VIHS
Value
2 tCYCP
Max
-
Unit
Remarks
ns
tTRGL
tTRGH
TGIN
Min
VIHS
VILS
VILS
Note:
−
tCYCP indicates the APB bus clock cycle time.
For the number of the APB bus to which the Base Timer has been connected, see "8. Block Diagram".
Document Number: 001-99223 Rev.*A
Page 85 of 129
S6E1B8 Series
11.4.9 CSIO/SPI/UART Timing
CSIO (SPI=0, SCINV=0)
Parameter
(VCC=AVCC=1.65 V to 3.6 V, VSS=AVSS=0 V, TA=- 40°C to +105°C)
Symbol
Serial clock cycle time
tSCYC
SCK ↓ → SOT delay time
tSLOVI
SIN → SCK ↑ setup time
tIVSHI
SCK ↑ → SIN hold time
tSHIXI
Serial clock L pulse width
Serial clock H pulse width
tSLSH
tSHSL
SCK ↓ → SOT delay time
tSLOVE
SIN → SCK ↑ setup time
tIVSHE
SCK ↑ → SIN hold time
tSHIXE
SCK falling time
SCK rising time
tF
tR
Pin
Name
SCKx
SCKx,
SOTx
SCKx,
SINx
SCKx,
SINx
SCKx
SCKx
SCKx,
SOTx
SCKx,
SINx
SCKx,
SINx
SCKx
SCKx
Conditions
Master mode
Slave mode
VCC < 2.7 V
Min
Max
4 tCYCP
-
VCC ≥ 2.7 V
Min
Max
4 tCYCP
-
Unit
ns
- 30
+ 30
- 20
+ 20
ns
60
-
50
-
ns
0
-
0
-
ns
2 tCYCP - 10
tCYCP +10
-
2 tCYCP - 10
tCYCP +10
-
ns
ns
-
65
-
52
ns
10
-
10
-
ns
20
-
20
-
ns
-
5
5
-
5
5
ns
ns
Notes:
−
The above AC characteristics are for clock synchronous mode.
−
tCYCP represents the APB bus clock cycle time.
For the number of the APB bus to which Multi-function Serial has been connected, see "8. Block Diagram ".
−
The characteristics are only applicable when the relocate port numbers are the same.
For instance, they are not applicable for the combination of SCKx_0 and SOTx_1.
−
External load capacitance CL=30 pF
Document Number: 001-99223 Rev.*A
Page 86 of 129
S6E1B8 Series
tSCYC
VOH
SCK
VOL
VOL
tSLOVI
VOH
SOT
VOL
tIVSHI
SIN
tSHIXI
VIH
VIH
VIL
VIL
Master mode
tSLSH
SCK
VIH
tF
tSHSL
VIL
VIL
tSLOVE
SOT
VIH
tR
VOH
VOL
tIVSHE
SIN
VIH
VIH
VIL
tSHIXE
VIH
VIL
Slave mode
Document Number: 001-99223 Rev.*A
Page 87 of 129
S6E1B8 Series
CSIO (SPI=0, SCINV=1)
Parameter
(VCC=AVCC=1.65 V to 3.6 V, VSS=AVSS=0 V, TA=- 40°C to +105°C)
Symbol
Serial clock cycle time
tSCYC
SCK ↑ → SOT delay time
tSHOVI
SIN → SCK ↓ setup time
tIVSLI
SCK ↓ → SIN hold time
tSLIXI
Serial clock L pulse width
Serial clock H pulse width
tSLSH
tSHSL
SCK ↑ → SOT delay time
tSHOVE
SIN → SCK ↓ setup time
tIVSLE
SCK ↓ → SIN hold time
tSLIXE
SCK falling time
SCK rising time
tF
tR
Pin
Name
SCKx
SCKx,
SOTx
SCKx,
SINx
SCKx,
SINx
SCKx
SCKx
SCKx,
SOTx
SCKx,
SINx
SCKx,
SINx
SCKx
SCKx
Conditions
Master mode
Slave mode
VCC < 2.7 V
Min
Max
4 tCYCP
-
VCC ≥ 2.7 V
Min
Max
4 tCYCP
-
Unit
ns
- 30
+ 30
- 20
+ 20
ns
60
-
50
-
ns
0
-
0
-
ns
2 tCYCP - 10
tCYCP +10
-
2 tCYCP - 10
tCYCP +10
-
ns
ns
-
65
-
52
ns
10
-
10
-
ns
20
-
20
-
ns
-
5
5
-
5
5
ns
ns
Notes:
−
The above AC characteristics are for clock synchronous mode.
−
tCYCP represents the APB bus clock cycle time.
For the number of the APB bus to which Multi-function Serial has been connected, see "8. Block Diagram ".
−
The characteristics are only applicable when the relocate port numbers are the same.
For instance, they are not applicable for the combination of SCKx_0 and SOTx_1.
−
External load capacitance CL=30 pF
Document Number: 001-99223 Rev.*A
Page 88 of 129
S6E1B8 Series
tSCYC
SCK
VOH
VOH
VOL
tSHOVI
VOH
SOT
VOL
tIVSLI
VIH
SIN
tSLIXI
VIH
VIL
VIL
Master mode
tSHSL
SCK
tSLSH
VIH
VIH
VIL
tR
tF
tSHOVE
SOT
VOH
VOL
tIVSLE
SIN
VIL
VIL
VIH
VIL
tSLIXE
VIH
VIL
Slave mode
Document Number: 001-99223 Rev.*A
Page 89 of 129
S6E1B8 Series
SPI (SPI=1, SCINV=0)
Parameter
(VCC=AVCC=1.65 V to 3.6 V, VSS=AVSS=0 V, TA=- 40°C to +105°C)
Symbol
Serial clock cycle time
tSCYC
SCK ↑ → SOT delay time
tSHOVI
SIN → SCK ↓ setup time
tIVSLI
SCK ↓→ SIN hold time
tSLIXI
SOT → SCK ↓ delay time
tSOVLI
Serial clock L pulse width
Serial clock H pulse width
tSLSH
tSHSL
SCK ↑ → SOT delay time
tSHOVE
SIN → SCK ↓ setup time
tIVSLE
SCK ↓→ SIN hold time
tSLIXE
SCK falling time
SCK rising time
tF
tR
Pin
Name
SCKx
SCKx,
SOTx
SCKx,
SINx
SCKx,
SINx
SCKx,
SOTx
SCKx
SCKx
SCKx,
SOTx
SCKx,
SINx
SCKx,
SINx
SCKx
SCKx
Conditions
Master mode
Slave mode
VCC < 2.7 V
Min
Max
4 tCYCP
-
VCC ≥ 2.7 V
Min
Max
4 tCYCP
-
Unit
ns
- 30
+ 30
- 20
+ 20
ns
60
-
50
-
ns
0
-
0
-
ns
2 tCYCP - 30
-
2 tCYCP - 30
-
ns
2 tCYCP - 10
tCYCP +10
-
2 tCYCP - 10
tCYCP +10
-
ns
ns
-
65
-
52
ns
10
-
10
-
ns
20
-
20
-
ns
-
5
5
-
5
5
ns
ns
Notes:
−
The above AC characteristics are for clock synchronous mode.
−
tCYCP represents the APB bus clock cycle time.
For the number of the APB bus to which Multi-function Serial has been connected, see "8. Block Diagram ".
−
The characteristics are only applicable when the relocate port numbers are the same.
For instance, they are not applicable for the combination of SCKx_0 and SOTx_1.
−
External load capacitance CL=30 pF
Document Number: 001-99223 Rev.*A
Page 90 of 129
S6E1B8 Series
tSCYC
SCK
tSOVLI
SOT
VOH
VOL
VOH
VOL
VOH
VOL
VIH
VIL
SIN
VOL
tSHOVI
tIVSLI
tSLIXI
VIH
VIL
Master mode
tSLSH
VIH
SCK
*
SOT
VIL
tSHSL
VIL
tF
tR
VOH
VOL
SIN
VIH
VIL
tIVSLE
*: Changes when writing to TDR register
Document Number: 001-99223 Rev.*A
tSLIXE
VIH
VIH
tSHOVE
VOH
VOL
VIH
VIL
Slave mode
Page 91 of 129
S6E1B8 Series
SPI (SPI=1, SCINV=1)
Parameter
(VCC=AVCC=1.65 V to 3.6 V, VSS=AVSS=0 V, TA=- 40°C to +105°C)
Symbol
Serial clock cycle time
tSCYC
SCK ↓ → SOT delay time
tSLOVI
SIN → SCK ↑ setup time
tIVSHI
SCK ↑ → SIN hold time
tSHIXI
SOT → SCK ↑ delay time
tSOVHI
Serial clock L pulse width
Serial clock H pulse width
tSLSH
tSHSL
SCK ↓ → SOT delay time
tSLOVE
SIN → SCK ↑ setup time
tIVSHE
SCK ↑ → SIN hold time
tSHIXE
SCK falling time
SCK rising time
tF
tR
Pin
Name
SCKx
Conditions
SCKx,
SOTx
SCKx,
SINx
SCKx,
SINx
SCKx,
SOTx
SCKx
SCKx
SCKx,
SOTx
SCKx,
SINx
SCKx,
SINx
SCKx
SCKx
Master mode
Slave mode
VCC < 2.7 V
Min
Max
4 tCYCP
-
VCC ≥ 2.7 V
Min
Max
4 tCYCP
-
Unit
ns
-30
+30
-20
+20
ns
60
-
50
-
ns
0
-
0
-
ns
2 tCYCP - 30
-
2 tCYCP - 30
-
ns
2 tCYCP - 10
tCYCP +10
-
2 tCYCP - 10
tCYCP +10
-
ns
ns
-
65
-
52
ns
10
-
10
-
ns
20
-
20
-
ns
-
5
5
-
5
5
ns
ns
Notes:
−
The above AC characteristics are for clock synchronous mode.
−
tCYCP represents the APB bus clock cycle time.
For the number of the APB bus to which Multi-function Serial has been connected, see "8. Block Diagram ".
−
The characteristics are only applicable when the relocate port numbers are the same.
For instance, they are not applicable for the combination of SCKx_0 and SOTx_1.
−
External load capacitance CL=30 pF
Document Number: 001-99223 Rev.*A
Page 92 of 129
S6E1B8 Series
tSCYC
VOH
SCK
tSOVHI
SOT
tSLOVI
VOH
VOL
VOH
VOL
tSHIXI
tIVSHI
VIH
VIL
SIN
VOH
VOL
VIH
VIL
Master mode
tR
SCK
SOT
VIL
VIH
VIH
tSLSH
VIL
tSLOVE
VOH
VOL
tIVSHE
SIN
tF
tSHSL
VIL
VOH
VOL
tSHIXE
VIH
VIL
VIH
VIL
Slave mode
Document Number: 001-99223 Rev.*A
Page 93 of 129
S6E1B8 Series
When Using CSIO/SPI Chip Select (SCINV=0, CSLVL=1)
(VCC=AVCC=1.65 V to 3.6 V, VSS=AVSS=0 V, TA=- 40°C to +105°C)
Parameter
Symbol
Conditions
VCC < 2.7 V
Min
VCC ≥ 2.7 V
Max
Unit
Max
Min
(*1)-50
(*1)+0
(*1)-50
(*1)+0
ns
(*2)+0
(*2)+50
(*2)+0
(*2)+50
ns
SCS↓→SCK↓ setup time
tCSSI
SCK↑→SCS↑ hold time
tCSHI
SCS deselect time
tCSDI
(*3)-50
(*3)+50
(*3)-50
(*3)+50
ns
SCS↓→SCK↓ setup time
tCSSE
3tCYCP+30
-
3tCYCP+30
-
ns
SCK↑→SCS↑ hold time
tCSHE
0
-
0
-
ns
SCS deselect time
tCSDE
3tCYCP+30
-
3tCYCP+30
-
ns
SCS↓→SOT delay time
tDSE
-
55
-
43
ns
SCS↑→SOT delay time
tDEE
0
-
0
-
ns
Master mode
Slave mode
*1: CSSU bit value × serial chip select timing operating clock cycle.
*2: CSHD bit value × serial chip select timing operating clock cycle.
*3: CSDS bit value × serial chip select timing operating clock cycle.
Irrespective of CSDS bit setting, 5tCYCP or more are required for the period the time when the serial chip select pin becomes
inactive to the time when the serial chip select pin becomes active again.
Notes:
−
tCYCP indicates the APB bus clock cycle time.
For information about the APB bus number which Multi-function Serial is connected to, see "8. Block Diagram ".
−
−
For information about CSSU, CSHD, CSDS, serial chip select timing operating clock, see "FM0+ Family Peripheral Manual".
−
When the external load capacitance CL=30 pF.
These characteristics only guarantee the same relocate port number.
For example, the combination of SCKx_0 and SCSIx_1 is not guaranteed.
Document Number: 001-99223 Rev.*A
Page 94 of 129
S6E1B8 Series
SCSO
tCSSI
tCSHI
tCSDI
tCSHE
tCSDE
SCK
SOT
(SPI=0)
SOT
(SPI=1)
Master mode
SCSI
tCSSE
SCK
tDEE
SOT
(SPI=0)
tDSE
SOT
(SPI=1)
Slave mode
Document Number: 001-99223 Rev.*A
Page 95 of 129
S6E1B8 Series
When Using CSIO/SPI Chip Select (SCINV=1, CSLVL=1)
(VCC=AVCC=1.65 V to 3.6 V, VSS=AVSS=0 V, TA=- 40°C to +105°C)
Parameter
Symbol
SCS↓→SCK↑ setup time
tCSSI
SCK↓→SCS↑ hold time
tCSHI
Conditions
Master mode
VCC < 2.7 V
VCC ≥ 2.7 V
Unit
Min
Max
Min
Max
(*1)-50
(*1)+0
(*1)-50
(*1)+0
ns
(*2)+0
(*2)+50
(*2)+0
(*2)+50
ns
SCS deselect time
tCSDI
(*3)-50
(*3)+50
(*3)-50
(*3)+50
ns
SCS↓→SCK↑ setup time
tCSSE
3tCYCP+30
-
3tCYCP+30
-
ns
SCK↓→SCS↑ hold time
tCSHE
0
-
0
-
ns
SCS deselect time
tCSDE
3tCYCP+30
-
3tCYCP+30
-
ns
SCS↓→SOT delay time
tDSE
-
55
-
43
ns
SCS↑→SOT delay time
tDEE
0
-
0
-
ns
Slave mode
*1: CSSU bit value × serial chip select timing operating clock cycle.
*2: CSHD bit value × serial chip select timing operating clock cycle.
*3: CSDS bit value × serial chip select timing operating clock cycle.
Irrespective of CSDS bit setting, 5tCYCP or more are required for the period the time when the serial chip select pin becomes
inactive to the time when the serial chip select pin becomes active again.
Notes:
−
tCYCP indicates the APB bus clock cycle time.
For information about the APB bus number which Multi-function Serial is connected to, see "8. Block Diagram ".
−
−
For information about CSSU, CSHD, CSDS, serial chip select timing operating clock, see "FM0+ Family Peripheral Manual".
−
When the external load capacitance CL=30 pF.
These characteristics only guarantee the same relocate port number.
For example, the combination of SCKx_0 and SCSIx_1 is not guaranteed.
Document Number: 001-99223 Rev.*A
Page 96 of 129
S6E1B8 Series
SCSO
tCSSI
tCSHI
tCSDI
tCSHE
tCSDE
SCK
SOT
(SPI=0)
SOT
(SPI=1)
Master mode
SCSI
tCSSE
SCK
tDEE
SOT
(SPI=0)
tDSE
SOT
(SPI=1)
Slave mode
Document Number: 001-99223 Rev.*A
Page 97 of 129
S6E1B8 Series
When Using CSIO/SPI Chip Select (SCINV=0, CSLVL=0)
(VCC=AVCC=1.65 V to 3.6 V, VSS=AVSS=0 V, TA=- 40°C to +105°C)
Parameter
SCS↑→SCK↓ setup time
Symbol
Conditions
tCSSI
VCC < 2.7 V
VCC ≥ 2.7 V
Min
Max
Min
Max
(*1)-50
(*1)+0
(*1)-50
(*1)+0
Unit
ns
SCK↑→SCS↓ hold time
tCSHI
(*2)+0
(*2)+50
(*2)+0
(*2)+50
ns
SCS deselect time
tCSDI
(*3)-50
(*3)+50
(*3)-50
(*3)+50
ns
SCS↑→SCK↓ setup time
tCSSE
3tCYCP+30
-
3tCYCP+30
-
ns
SCK↑→SCS↓ hold time
tCSHE
SCS deselect time
tCSDE
SCS↑→SOT delay time
SCS↓→SOT delay time
Master mode
0
-
0
-
ns
3tCYCP+30
-
3tCYCP+30
-
ns
tDSE
-
55
-
43
ns
tDEE
0
-
0
-
ns
Slave mode
*1: CSSU bit value × serial chip select timing operating clock cycle.
*2: CSHD bit value × serial chip select timing operating clock cycle.
*3: CSDS bit value × serial chip select timing operating clock cycle.
Irrespective of CSDS bit setting, 5tCYCP or more are required for the period the time when the serial chip select pin becomes
inactive to the time when the serial chip select pin becomes active again.
Notes:
−
tCYCP indicates the APB bus clock cycle time.
For information about the APB bus number which Multi-function Serial is connected to, see "8. Block Diagram ".
−
For information About CSSU, CSHD, CSDS, serial chip select timing operating clock, see "FM0+ Family Peripheral Manual".
−
These characteristics only guarantee the same relocate port number.
For example, the combination of SCKx_0 and SCSIx_1 is not guaranteed.
−
When the external load capacitance CL=30 pF.
Document Number: 001-99223 Rev.*A
Page 98 of 129
S6E1B8 Series
tCSDI
SCSO
tCSSI
tCSHI
SCK
SOT
(SPI=0)
SOT
(SPI=1)
Master mode
tCSDE
SCSI
tCSSE
tCSHE
SCK
tDEE
SOT
(SPI=0)
SOT
tDSE
(SPI=1)
Slave mode
Document Number: 001-99223 Rev.*A
Page 99 of 129
S6E1B8 Series
When Using CSIO/SPI Chip Select (SCINV=1, CSLVL=0)
(VCC=AVCC=1.65 V to 3.6 V, VSS=AVSS=0 V, TA=- 40°C to +105°C)
Parameter
SCS↑→SCK↑ setup time
Symbol
Conditions
tCSSI
VCC < 2.7 V
VCC ≥ 2.7 V
Min
Max
Min
Max
(*1)-50
(*1)+0
(*1)-50
(*1)+0
Unit
ns
SCK↓→SCS↓ hold time
tCSHI
(*2)+0
(*2)+50
(*2)+0
(*2)+50
ns
SCS deselect time
tCSDI
(*3)-50
(*3)+50
(*3)-50
(*3)+50
ns
SCS↑→SCK↑ setup time
tCSSE
3tCYCP+30
-
3tCYCP+30
-
ns
SCK↓→SCS↓ hold time
tCSHE
SCS deselect time
tCSDE
SCS↑→SOT delay time
SCS↓→SOT delay time
Master mode
0
-
0
-
ns
3tCYCP+30
-
3tCYCP+30
-
ns
tDSE
-
55
-
43
ns
tDEE
0
-
0
-
ns
Slave mode
*1: CSSU bit value × serial chip select timing operating clock cycle.
*2: CSHD bit value × serial chip select timing operating clock cycle.
*3: CSDS bit value × serial chip select timing operating clock cycle.
Irrespective of CSDS bit setting, 5tCYCP or more are required for the period the time when the serial chip select pin becomes
inactive to the time when the serial chip select pin becomes active again.
Notes:
−
tCYCP indicates the APB bus clock cycle time.
For information about the APB bus number which Multi-function Serial is connected to, see "8. Block Diagram ".
−
For information about CSSU, CSHD, CSDS, serial chip select timing operating clock, see "FM0+ Family Peripheral Manual".
−
These characteristics only guarantee the same relocate port number.
For example, the combination of SCKx_0 and SCSIx_1 is not guaranteed.
−
When the external load capacitance CL=30 pF.
Document Number: 001-99223 Rev.*A
Page 100 of 129
S6E1B8 Series
tCSDI
SCSO
tCSSI
tCSHI
SCK
SOT
(SPI=0)
SOT
(SPI=1)
Master mode
tCSDE
SCSI
tCSSE
tCSHE
SCK
tDEE
SOT
(SPI=0)
tDSE
SOT
(SPI=1)
Slave mode
Document Number: 001-99223 Rev.*A
Page 101 of 129
S6E1B8 Series
UART external clock input (EXT=1)
Parameter
Serial clock L pulse width
Serial clock H pulse width
SCK falling time
SCK rising time
(VCC=AVCC=1.65 V to 3.6 V, VSS=AVSS=0 V, TA=- 40°C to +105°C)
Symbol
tSLSH
tSHSL
tF
tR
Document Number: 001-99223 Rev.*A
VIL
Min
tCYCP +10
tCYCP +10
-
CL=30 pF
tR
SCK
Value
Conditions
tF
tSHSL
VIH
VIH
VIL
Max
5
5
Unit
Remarks
ns
ns
ns
ns
tSLSH
VIL
Page 102 of 129
S6E1B8 Series
11.4.10 External Input Timing
Parameter
(VCC=AVCC=1.65 V to 3.6 V, VSS=AVSS=0 V, TA=- 40°C to +105°C)
Symbol
Pin Name
Value
Min
Conditions
Max
Unit
ADTGx
Input pulse width
1
-
FRCKx
2 tCYCP*
-
ns
ICxx
tINH, tINL
DTTIxX
1
-
2 tCYCP*
1
Remarks
A/D converter
trigger input
-
ns
INTxx, NMIX
*2
*3
2 tCYCP +100*
500
-
ns
ns
WKUPx
*4
500
-
ns
Free-run timer
input clock
Input capture
Wave form
generator
External interrupt,
NMI
Deep standby
wake up
*1: tCYCP represents the APB bus clock cycle time.
For the number of the APB bus to which the Multi-function Timer is connected and that of the APB bus to which the External
Interrupt Controller is connected, see "8. Block Diagram".
*2: In Run mode and Sleep mode
*3: In Timer mode and RTC mode and Stop mode
*4: In Deep Standby RTC mode and Deep Standby Stop mode
tINH
VILS
Document Number: 001-99223 Rev.*A
tINL
VILS
VIHS
VIHS
Page 103 of 129
S6E1B8 Series
2
11.4.11 I C Timing
(VCC=AVCC=1.65 V to 3.6 V, VSS=AVSS=0 V, TA=- 40°C to +105°C)
Parameter
Symbol
Conditions
Standard-Mode
Min
Max
0
100
Fast-Mode
Min
Max
0
400
Unit
Remarks
SCL clock frequency
fSCL
kHz
(Repeated) Start condition hold
time
tHDSTA
4.0
0.6
μs
SDA ↓ → SCL ↓
SCL clock L width
tLOW
4.7
1.3
μs
SCL clock H width
tHIGH
4.0
0.6
μs
(Repeated) Start setup time
tSUSTA
4.7
0.6
μs
SCL ↑ → SDA ↓
CL=30 pF,
1
Data hold time
2
3
R=(VP/IOL)*
tHDDAT
0
3.45*
0
0.9*
μs
SCL ↓ → SDA ↓ ↑
Data setup time
tSUDAT
250
100
ns
SDA ↓ ↑ → SCL ↑
Stop condition setup time
tSUSTO
4.0
0.6
μs
SCL ↑ → SDA ↑
Bus free time between
Stop condition and
tBUF
4.7
1.3
μs
Start condition
4
4
Noise filter
tSP
2 tCYCP*
2 tCYCP*
ns
*1: R represents the pull-up resistance of the SCL and SDA lines, and CL the load capacitance of the SCL and SDA lines. VP
represents the power supply voltage of the pull-up resistance, and IOL the VOL guaranteed current.
*2: The maximum tHDDAT must satisfy at least the condition that the period during which the device is holding the SCL signal at L
(tLOW) does not extend.
2
2
*3: A Fast-mode I C bus device can be used in a Standard-mode I C bus system, provided that the condition of tSUDAT ≥ 250 ns is
fulfilled.
*4: tCYCP represents the APB bus clock cycle time.
2
For the number of the APB bus to which the I C is connected, see "8. Block Diagram".
To use Standard-mode, set the APB bus clock at 2 MHz or more.
To use Fast-mode, set the APB bus clock at 8 MHz or more.
SDA
tSUDAT
tLOW
tSUSTA
tBUF
SCL
tHDSTA
Document Number: 001-99223 Rev.*A
tHDDAT
tHIGH
tHDSTA
tSP
tSUSTO
Page 104 of 129
S6E1B8 Series
2
11.4.12 I S Timing
(VCC=AVCC=1.65 V to 3.6 V, VSS=AVSS=0 V, TA=- 40°C to +105°C)
Parameter
Symbol
Pin Name
MI2SCK max frequency*
2
1
I S clock cycle time*
2
I S clock Duty cycle
fMI2SCK
tICYC
∆
MI2SCK↓ → MI2SWS delay time
tSWDT
MI2SCK↓ → MI2SDO delay time
tSDDT
MI2SDI → MI2SCK ↑ setup
time
tDSST
MI2SCK ↑ → MI2SDI hold time
tSDHT
MI2SCKx
MI2SCKx
MI2SCKx
MI2SCKx,
MI2SWSx
MI2SCKx,
MI2SDOx
MI2SCKx,
MI2SDIx
MI2SCKx,
MI2SDIx
MI2SCKx
MI2SCKx
1
MI2SCK falling time
MI2SCK rising time
tF
tR
Conditions
CL=30 pF
VCC < 2.7 V
Min
Max
6.144
4 tCYCP
45%
55%
VCC ≥ 2.7 V
Min
Max
6.144
4 tCYCP
45%
55%
Unit
MHz
ns
-30
+30
-20
+20
ns
-30
+30
-20
+20
ns
50
-
36
-
ns
0
-
0
-
ns
-
5
5
-
5
5
ns
ns
*1: I2S clock should meet the multiple of PCLK (tICYC) and the frequency less than fMI2SCK meantime. The detail information please
refer to Chapter I2S of Communication Macro Part of Peripheral Manual.
VIH
MI2SCK
tF
MI2SWS
and
MI2SDO
VIH
VIL
VIL
tR
tSWDT,
tSDDT
VOH
VOL
tDSST
MI2SDI
Document Number: 001-99223 Rev.*A
tSDHT
VIH
VIH
VIL
VIL
Page 105 of 129
S6E1B8 Series
11.4.13 Smart Card Interface Characteristics
(VCC=1.65 V to 3.3 V, VSS=0 V, TA=- 40°C to +105°C)
Parameter
Symbol
Output rising time
tR
Output falling time
tF
Output clock frequency
Duty cycle
fCLK
∆
Pin Name
Conditions
ICx_VCC,
ICx_RST,
ICx_CLK,
ICx_DATA
ICx_CLK
CL=30 pF
Value
Unit
Min
Max
4
20
ns
4
20
ns
-
20
MHz
45%
55%
Remarks
External pull-up resistor (20 kΩ to 50 kΩ) must be applied to ICx_CIN pin when it’s used as smart card reader function.
Document Number: 001-99223 Rev.*A
Page 106 of 129
S6E1B8 Series
11.4.14 SW-DP Timing
Parameter
(VCC=AVCC=1.65 V to 3.6 V, VSS=AVSS=0 V, TA=- 40°C to +105°C)
Value
Unit
Symbol
Pin Name
Conditions
SWDIO setup time
tSWS
SWCLK,
SWDIO
-
15
-
ns
SWDIO hold time
tSWH
SWCLK,
SWDIO
-
15
-
ns
SWDIO delay time
tSWD
SWCLK,
SWDIO
-
-
45
ns
Min
Max
Remarks
Note:
−
External load capacitance CL=30 pF
SWCLK
VOH
VOL
tJTAGS
VOH
VOL
SWDIO
(When input)
tJTAGH
VOH
VOL
tSWD
JTAGD
SWDIO
(When output)
Document Number: 001-99223 Rev.*A
VOH
VOL
Page 107 of 129
S6E1B8 Series
11.5 12-bit A/D Converter
Electrical Characteristics of A/D Converter (Preliminary Values)
(VCC=AVCC=1.65 V to 3.6 V, VSS=AVSS=0 V, TA=- 40°C to +105°C)
Parameter
Resolution
Integral Nonlinearity
Differential Nonlinearity
Zero transition voltage
Full-scale transition voltage
1
Conversion time *
2
Sampling time *
3
Compare clock cycle *
Symbol
Pin Name
VZT
VFST
ANxx
ANxx
-
-
tS
-
tCCK
-
Min
- 4.5
- 2.5
- 15
AVRH - 15
1.0
4.0
10
0.3
1.2
3.0
50
200
500
Value
Typ
-
Max
12
4.5
+ 2.5
+ 15
AVRH + 15
-
Unit
bit
LSB
LSB
mV
mV
μs
10
μs
1000
ns
State transition time to
operation permission
Analog input capacity
tSTT
-
-
-
1.0
μs
CAIN
-
-
-
pF
Analog input resistance
RAIN
-
-
-
-
ANxx
ANxx
9.7
2.2
5.5
10.5
4
5
AVRH
Interchannel disparity
Analog port input leak current
Analog input voltage
kΩ
Remarks
AVCC ≥ 2.7 V
1.8 ≤ AVCC < 2.7 V
1.65 ≤ AVCC < 1.8 V
AVCC ≥ 2.7 V
1.8 ≤ AVCC < 2.7 V
1.65 ≤ AVCC < 1.8 V
AVCC ≥ 2.7 V
1.8 ≤ AVCC < 2.7 V
1.65 ≤ AVCC < 1.8 V
AVCC ≥ 2.7 V
1.8 ≤ AVCC < 2.7 V
1.65 ≤ AVCC < 1.8 V
LSB
μA
AVSS
V
AVCC ≥ 2.7V
2.7
Reference voltage
AVCC
V
AVRH
AVCC < 2.7V
AVCC
*1: The conversion time is the value of sampling time (tS) + compare time (tC).
The minimum conversion time is computed according to the following conditions:
sampling time=0.3 μs, compare time=0.7 μs
AVCC ≥ 2.7 V
sampling time=1.2 μs, compare time=2.8 μs
1.8 ≤ AVCC < 2.7 V
1.65 ≤ AVCC < 1.8 V sampling time=3.0 μs, compare time=7.0 μs
Ensure that the conversion time satisfies the specifications of the sampling time (tS) and compare clock cycle (tCCK).
For details of the settings of the sampling time and compare clock cycle, refer to "Chapter: A/D Converter" in "FM0+ Family
Peripheral Manual Analog Macro Part".
The register settings of the A/D Converter are reflected in the operation according to the APB bus clock timing.
For the number of the APB bus to which the A/D Converter is connected, see "8. Block Diagram".
The base clock (HCLK) is used to generate the sampling time and the compare clock cycle.
*2: The required sampling time varies according to the external impedance.
Set a sampling time that satisfies (Equation 1).
*3: The compare time (tC) is the result of (Equation 2).
Document Number: 001-99223 Rev.*A
Page 108 of 129
S6E1B8 Series
ANxx
Analog input pins
Analog signal
source
REXT
Comparator
RAIN
CAIN
(Equation 1) tS ≥ (RAIN + REXT ) × CAIN × 9
tS:
Sampling time
RAIN:
Input resistance of A/D Converter = 2.2 kΩ with 2.7 < AVCC < 3.6 ch.1 to ch.14, ch.16 to ch.19
Input resistance of A/D Converter = 1.9 kΩ with 2.7 < AVCC < 3.6 ch.15
Input resistance of A/D Converter = 2.3 kΩ with 2.7 < AVCC < 3.6 ch.20 to ch.23
Input resistance of A/D Converter = 5.7 kΩ with 1.8 < AVCC < 2.7 ch.1 to ch.14, ch.16 to ch.19
Input resistance of A/D Converter = 5.6 kΩ with 1.8 < AVCC < 2.7 ch.15
Input resistance of A/D Converter = 5.8 kΩ with 1.8 < AVCC < 2.7 ch.20 to ch.23
Input resistance of A/D Converter = 12.6 kΩ with 1.65 < AVCC < 1.8 ch.1 to ch.19
Input resistance of A/D Converter = 12.7 kΩ with 1.65 < AVCC < 1.8 ch.20 to ch.23
CAIN:
Input capacitance of A/D Converter = 9.7 pF with 2.7 < AVCC < 3.6
REXT:
Output impedance of external circuit
(Equation 2) tC=tCCK × 14
tC:
Compare time
tCCK :
Compare clock cycle
Document Number: 001-99223 Rev.*A
Page 109 of 129
S6E1B8 Series
Definitions of 12-bit A/D Converter Terms
Resolution:
Analog variation that is recognized by an A/D converter.
Integral Nonlinearity:
Deviation of the line between the zero-transition point (0b000000000000 ←→ 0b000000000001) and the
full-scale transition point (0b111111111110 ←→ 0b111111111111) from the actual conversion characteristics.
Differential Nonlinearity: Deviation from the ideal value of the input voltage that is required to change the output code by 1 LSB.
Integral Nonlinearity
0xFFF
Actual conversion
characteristics
0xFFE
0x(N+1)
{1 LSB(N-1) + VZT}
VFST
VNT
0x004
(Actuallymeasured
value)
(Actually-measured
value)
0x003
Digital output
Digital output
0xFFD
Differential Nonlinearity
0x001
Analog input
:
:
:
:
(Actually-measured
value)
0x(N-2)
AVRH
Differential Nonlinearity of digital output N =
N
VZT
VFST
VNT
(Actually-measured
value)
Actual conversion characteristics
Integral Nonlinearity of digital output N =
1LSB =
V(N+1)T
VNT
VZT (Actually-measured value)
AVSS
Ideal characteristics
0x(N-1)
Actual conversion
characteristics
Ideal characteristics
0x002
0xN
Actual conversion
characteristics
AVSS
Analog input
VNT - {1LSB × (N - 1) + VZT}
1LSB
V(N + 1) T - VNT
1LSB
AVRH
[LSB]
- 1 [LSB]
VFST – VZT
4094
A/D converter digital output value.
Voltage at which the digital output changes from 0x000 to 0x001.
Voltage at which the digital output changes from 0xFFE to 0xFFF.
Voltage at which the digital output changes from 0x(N − 1) to 0xN.
Document Number: 001-99223 Rev.*A
Page 110 of 129
S6E1B8 Series
11.6 USB Characteristics
(VCC=3.0 V to 3.6 V, VSS=0 V, TA=- 40°C to +105°C)
Parameter
Input
characteristics
Symbol
Pin
Name
Conditions
Input H level voltage
VIH
-
Input L level voltage
VIL
-
Differential input sensitivity
VDI
-
Differential common mode range
VCM
-
Value
Min
2.0
VSS –
VCC +
0.3
Unit
V
Remarks
*1
*1
0.8
V
0.2
-
V
*2
0.8
2.5
V
*2
2.8
3.6
V
0.0
0.3
V
0.3
External pull-down
Max
*3
Output H level voltage
VOH
Output L level voltage
VOL
Crossover voltage
VCRS
-
1.3
2.0
V
*4
resistance = 15 kΩ
UDP0,
External pull-up
UDM0
resistance = 1.5 kΩ
*3
Output
Rising time
tFR
Full-speed
4
20
ns
*5
characteristic
Falling time
tFF
Full-speed
4
20
ns
*5
Rising/Falling time matching
tFRFM
Full-speed
90
111.11
%
*5
Output impedance
ZDRV
Full-speed
28
44
Ω
*6
tLR
Low-speed
75
300
ns
*7
tLF
Low-speed
75
300
ns
*7
tLRFM
Low-speed
80
125
%
*7
Rising time
Falling time
Rising/Falling time matching
*1 :
Minimum differential input sensitivity [V]
*2 :
The switching threshold voltage of single-end-receiver of USB I/O buffer is set as within VIL(Max)=0.8 V, VIH(Min)=2.0 V
(TTL input standard).
There are some hysteresis to lower noise sensitivity.
Use differential-receiver to receive USB differential data signal.
Differential-receiver has 200 mV of differential input sensitivity when the differential data input is within 0.8 V to 2.5 V to the
local ground reference level.
Above voltage range is the common mode input voltage range.
1.0
0.2
Document Number: 001-99223 Rev.*A
0.8
2.5
Common mode input voltage [V]
Page 111 of 129
S6E1B8 Series
*3 :
*4 :
The output drive capability of the driver is below 0.3 V at Low-state (VOL) (to 3.6 V and 1.5 kΩ load), and 2.8 V or above (to
the VSS and 1.5 kΩ load) at high-state (VOH)
The cross voltage of the external differential output signal (D+ / D-) of USB I/O buffer is within 1.3 V to 2.0 V.
D+
Max 2.0V
VCRS specified range
Min 1.3V
D-
*5 :
The indicate rising time (Trise) and falling time (Tfall) of the full-speed differential data signal.
They are defined by the time between 10% and 90% of the output signal voltage.
For full-speed buffer, Tr/Tf ratio is regulated as within ±10% to minimize RFI emission.
D+
90%
90%
10%
10%
DTrise
Rising time
Tfall
Falling time
Full-speed buffer
Rs=27 Ω
TxD+
CL=50 pF
Rs=27 Ω
TxDCL=50 pF
3-state enable
*6 :
USB Full-speed connection is performed via twist pair cable shield with 90 Ω ± 15% characteristic impedance (Differential
Mode).
USB standard defines that output impedance of USB driver must be in range from 28Ω to 44Ω. So, discrete series resistor
(Rs) addition is defined in order to satisfy the above definition and keep balance.
When using this USB I/O, use it with 25 Ω to 33 Ω (recommendation value : 27 Ω) series resistor Rs.
Document Number: 001-99223 Rev.*A
Page 112 of 129
S6E1B8 Series
Full-speed buffer
Rs
TxD+
28 Ω to 44 Ω equivalent impedance
Rs
TxD-
28 Ω to 44 Ω equivalent impedance
Mount it as external resistance.
3-state enable
Rs series resistor 25 Ω to 30 Ω
Series resistor of 27 Ω (recommendation value) must be added.
And, use “resistance with an uncertainty of 5% by E24 sequence”.
*7 :
They indicate rising time (Trise) and falling time (Tfall) of the low-speed differential data signal.
They are defined by the time between 10% and 90% of the output signal voltage.
D+
90%
90%
10%
10%
DTrise
Rising time
Tfall
Falling time
See “Low-speed load (Compliance Load)” for condition of external load.
Document Number: 001-99223 Rev.*A
Page 113 of 129
S6E1B8 Series
・ Low-Speed Load (Upstream Port Load) – Reference 1
Low-speed buffer
Rs=27 Ω
TxD+
Rpd
CL=50 pF to 150 pF
Rs=27 Ω
TxDRpd
3-state enable
CL=50 pF to 150 pF
Rpd=15 kΩ
・ Low-Speed Load (Downstream Port Load) – Reference 2
Low-speed buffer
Rs=27 Ω
VTERM
TxD+
CL=200 pF to
600 pF
Rs=27 Ω
TxD-
CL=50 pF to 150 pF
3-state enable
Document Number: 001-99223 Rev.*A
Rpu=1.5 kΩ
VTERM=3.6 V
Page 114 of 129
S6E1B8 Series
・ Low-Speed Load (Compliance Load)
Low-speed buffer
Rs=27 Ω
TxD+
CL=200 pF to 450 pF
Rs=27 Ω
TxDCL=200 pF to 450 pF
3-state enable
Document Number: 001-99223 Rev.*A
Page 115 of 129
S6E1B8 Series
11.7 Low-Voltage Detection Characteristics
11.7.1 Low-Voltage Detection Reset
Parameter
Symbol
(TA=-40°C to +105°C)
Conditions
Min
1.38
1.43
Value
Typ
1.50
1.55
Max
1.60
1.65
Unit
Detected voltage
Released voltage
VDL
VDH
LVD stabilization wait
time
tLVDW
-
-
-
8160×
*2
tCYCP
μs
LVD detection delay time
tLVDDL
-
-
-
200
μs
Fixed
*1
V
V
Remarks
When voltage drops
When voltage rises
*1: The value of low voltage detection reset is always fixed.
*2: tCYCP indicates the APB1 bus clock cycle time.
Document Number: 001-99223 Rev.*A
Page 116 of 129
S6E1B8 Series
11.7.2 Low-Voltage Detection Interrupt
Parameter
(TA=-40°C to +105°C)
SVHI=00100
SVHRLI=00100
SVHI=00101
SVHRLI=00101
SVHI=00110
SVHRLI=00110
SVHI=00111
SVHRLI=00111
SVHI=01000
SVHRLI=01000
SVHI=01001
SVHRLI=01001
SVHI=01010
SVHRLI=01010
SVHI=01011
SVHRLI=01011
SVHI=01100
SVHRLI=01100
SVHI=01101
SVHRLI=01101
SVHI=01110
SVHRLI=01110
SVHI=01111
SVHRLI=01111
SVHI=10000
SVHRLI=10000
SVHI=10001
SVHRLI=10001
SVHI=10010
SVHRLI=10010
SVHI=10011
SVHRLI=10011
Min
1.56
1.61
1.61
1.66
1.66
1.70
1.70
1.75
1.75
1.79
1.79
1.84
1.84
1.89
1.89
1.93
2.30
2.39
2.39
2.48
2.48
2.58
2.58
2.67
2.67
2.76
2.76
2.85
2.85
2.94
2.94
3.04
Value
Typ
1.70
1.75
1.75
1.80
1.80
1.85
1.85
1.90
1.90
1.95
1.95
2.00
2.00
2.05
2.05
2.10
2.50
2.60
2.60
2.70
2.70
2.80
2.80
2.90
2.90
3.00
3.00
3.10
3.10
3.20
3.20
3.30
tLVDW
-
-
-
tLVDDL
-
-
-
Symbol
Conditions
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
LVD stabilization wait time
LVD detection delay time
*:
Max
1.84
1.89
1.89
1.94
1.94
2.00
2.00
2.05
2.05
2.11
2.11
2.16
2.16
2.21
2.21
2.27
2.70
2.81
2.81
2.92
2.92
3.02
3.02
3.13
3.13
3.24
3.24
3.35
3.35
3.46
3.46
3.56
8160 ×
tCYCP*
200
Unit
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
Remarks
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
μs
μs
tCYCP represents the APB1 bus clock cycle time.
Document Number: 001-99223 Rev.*A
Page 117 of 129
S6E1B8 Series
11.7.3 Low-Voltage Detection Interrupt 2
Parameter
(TA=- 40°C to +105°C)
SVH2I=00100
SVH2RLI=00100
SVH2I=00101
SVH2RLI=00101
SVH2I=00110
SVH2RLI=00110
SVH2I=00111
SVH2RLI=00111
SVH2I=01000
SVH2RLI=01000
SVH2I=01001
SVH2RLI=01001
SVH2I=01010
SVH2RLI=01010
SVH2I=01011
SVH2RLI=01011
SVH2I=01100
SVH2RLI=01100
SVH2I=01101
SVH2RLI=01101
SVH2I=01110
SVH2RLI=01110
SVH2I=01111
SVH2RLI=01111
SVH2I=10000
SVH2RLI=10000
SVH2I=10001
SVH2RLI=10001
SVH2I=10010
SVH2RLI=10010
SVH2I=10011
SVH2RLI=10011
Min
1.56
1.61
1.61
1.66
1.66
1.70
1.70
1.75
1.75
1.79
1.79
1.84
1.84
1.89
1.89
1.93
2.30
2.39
2.39
2.48
2.48
2.58
2.58
2.67
2.67
2.76
2.76
2.85
2.85
2.94
2.94
3.04
Value
Typ
1.70
1.75
1.75
1.80
1.80
1.85
1.85
1.90
1.90
1.95
1.95
2.00
2.00
2.05
2.05
2.10
2.50
2.60
2.60
2.70
2.70
2.80
2.80
2.90
2.90
3.00
3.00
3.10
3.10
3.20
3.20
3.30
tLVDW
-
-
-
tLVDDL
-
-
-
Symbol
Conditions
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
LVD stabilization wait time
LVD detection delay time
Max
1.84
1.89
1.89
1.94
1.94
2.00
2.00
2.05
2.05
2.11
2.11
2.16
2.16
2.21
2.21
2.27
2.70
2.81
2.81
2.92
2.92
3.02
3.02
3.13
3.13
3.24
3.24
3.35
3.35
3.46
3.46
3.56
8160 ×
tCYCP*
200
Unit
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
Remarks
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
μs
μs
*: tCYCP represents the APB1 bus clock cycle time.
Document Number: 001-99223 Rev.*A
Page 118 of 129
S6E1B8 Series
11.8 Flash Memory Write/Erase Characteristics
Parameter
Sector erase time
Large sector
Small
sector
(VCC=1.65 V to 3.6 V, TA=- 40°C to +105°C)
Min
-
Value
Typ*
1.1
Max*
2.7
-
0.3
0.9
Unit
s
Remarks
The sector erase time includes the time of
writing prior to internal erase.
The halfword (16-bit) write time excludes the
system-level overhead.
The chip erase time includes the time of writing
Chip erase time
11.2
28.8
s
prior to internal erase.
*: The typical value is immediately after shipment, the maximum value is guarantee value under 10,000 cycle of erase/write.
Halfword (16-bit) write time
-
30
528
μs
Write/Erase Cycle and Data Hold Time (Target Value)
Write/Erase Cycle
Data Hold Time (Year)
1,000
20*
10,000
10*
Remarks
*: At average + 85°C
Document Number: 001-99223 Rev.*A
Page 119 of 129
S6E1B8 Series
11.9 Return Time from Low-Power Consumption Mode
11.9.1 Return Factor: Interrupt/WKUP
The return time from Low-Power consumption mode is indicated as follows. It is from receiving the return factor to starting the
program operation.
Return Count Time
Parameter
(VCC=1.65 V to 3.6 V, TA=-40°C to +105°C)
Symbol
Sleep mode
High-speed CR Timer mode,
Main Timer mode,
PLL Timer mode
Low-speed CR Timer mode
Sub Timer mode
tICNT
Typ
6*HCLK
Value
*1
Max
7*HCLK
Unit
μs
12*HCLK
13*HCLK
μs
20+12*HCLK
42+13*HCLK
μs
20+12*HCLK
42+13*HCLK
μs
71
(*2*4)
71+tOSCWT
μs
80
μs
(*3)
RTC mode,
38
(*2*4)
Stop mode
38+tOSCWT
Deep RTC mode,
45
Deep Stop mode
*1: The maximum value depends on the condition of environment.
Remarks
The count time is different in
different clock mode
*2: tOSCWT : Oscillator stabilization time.
*3: It is for HCR mode.
*4: For clock mode except HCR mode.
Operation Example of Return from Low-Power Consumption Mode (by External Interrupt*)
External
interrupt
Interrupt factor
accept
Active
tICNT
CPU
Operation
Interrupt factor
clear by CPU
Start
*: External interrupt is set to detecting fall edge.
Document Number: 001-99223 Rev.*A
Page 120 of 129
S6E1B8 Series
Operation Example of Return from Low-Power Consumption Mode (by Internal Resource Interrupt*)
Internal
resource
interrupt
Interrupt factor
accept
Active
tICNT
CPU
Operation
Interrupt factor
clear by CPU
Start
*: Internal resource interrupt is not included in return factor by the kind of Low-Power consumption mode.
Notes:
−
The return factor is different in each Low-Power consumption modes.
See "Chapter: Low Power Consumption Mode" and "Operations of Standby Modes" in FM0+ Family Peripheral Manual.
−
When interrupt recoveries, the operation mode that CPU recoveries depends on the state before the Low-Power consumption
mode transition. See "Chapter: Low Power Consumption Mode" in "FM0+ Family Peripheral Manual".
Document Number: 001-99223 Rev.*A
Page 121 of 129
S6E1B8 Series
11.9.2 Return Factor: Reset
The return time from Low-Power consumption mode is indicated as follows. It is from releasing reset to starting the program
operation.
Return Count Time
Parameter
(VCC=1.65 V to 3.6 V, TA=-40°C to +105°C)
Symbol
Typ
Value
*1
Max*
Unit
10
*2
40
70
μs
20
30
μs
61
114
μs
Sub Timer mode
61
114
μs
RTC/Stop mode
38
85
μs
95
μs
Sleep mode
High-speed CR Timer mode,
Main Timer mode,
PLL Timer mode
Low-speed CR Timer mode
tRCNT
Deep RTC mode,
46
Deep Stop mode
*: The maximum value depends on the accuracy of built-in CR.
Remarks
*1 : HCR ON.(HCR/MOSC/PLL
mode)
*2 : HCR OFF.(LCR/SOS mode)
Operation Example of Return from Low-Power Consumption Mode (by INITX)
INITX
Internal reset
Reset active
Release
tRCNT
CPU
Operation
Document Number: 001-99223 Rev.*A
Start
Page 122 of 129
S6E1B8 Series
Operation Example of Return from Low Power Consumption Mode (by Internal Resource Reset*)
Internal
resource
reset
Internal reset
Reset active
Release
tRCNT
CPU
Operation
Start
*: Internal resource reset is not included in return factor by the kind of Low-Power consumption mode.
Notes:
−
The return factor is different in each Low-Power consumption modes.
See "Chapter: Low Power Consumption Mode" and "Operations of Standby Modes" in FM0+ Family Peripheral Manual.
−
When interrupt recoveries, the operation mode that CPU recoveries depends on the state before the Low-Power consumption
mode transition. See "Chapter: Low Power Consumption Mode" in "FM0+ Family Peripheral Manual".
−
The time during the power-on reset/low-voltage detection reset is excluded. See "11.4.7 Power-on Reset Timing in 11.4 AC
Characteristics in 11. Electrical Characteristics" for the detail on the time during the power-on reset/low -voltage detection
reset.
−
When in recovery from reset, CPU changes to the high-speed CR run mode. When using the main clock or the PLL clock, it is
necessary to add the main clock oscillation stabilization wait time or the main PLL clock stabilization wait time.
−
The internal resource reset means the watchdog reset and the CSV reset.
Document Number: 001-99223 Rev.*A
Page 123 of 129
S6E1B8 Series
12. Ordering Information
Part Number
S6E1B84E0AGV2000A
S6E1B86E0AGV2000A
S6E1B84EHAGV2000A
S6E1B86EHAGV2000A
S6E1B84F0AGV20000
S6E1B86F0AGV20000
S6E1B84FHAGV20000
S6E1B86FHAGV20000
S6E1B84G0AGV20000
S6E1B86G0AGV20000
S6E1B84GHAGV20000
S6E1B86GHAGV20000
On-Chip
Flash
Memory
304
560
304
560
304
560
304
560
304
560
304
560
Document Number: 001-99223 Rev.*A
On-Chip
SRAM
32
64
32
64
32
64
32
64
32
64
32
64
AES
Calculator
Package
Packing
N/A
Plastic LQFP (0.50 mm pitch), 80
pins
(LQH080-02)
Tray
Plastic LQFP (0.50 mm pitch), 100
pins
(LQI100)
Tray
Plastic LQFP (0.50 mm pitch), 120
pins
(LQM120)
Tray
Yes
N/A
Yes
N/A
Yes
Page 124 of 129
S6E1B8 Series
13. Package Dimensions
Document Number: 001-99223 Rev.*A
Page 125 of 129
S6E1B8 Series
Document Number: 001-99223 Rev.*A
Page 126 of 129
S6E1B8 Series
Document Number: 001-99223 Rev.*A
Page 127 of 129
S6E1B8 Series
Document History
Document Title: S6E1B8 Series 32-bit ARM® Cortex®-M0+ FM0+ Microcontroller
Document Number: 001-99223
Revision
**
ECN
4889752
Orig. of
Change
TEKA
Submission Date
08/31/2015
Description of Change
New Spec.
Corrected Channel of Serial chip select function on CSIO in “Features”
Changed Conversion time of A/D Converter in “Features” and “11.5 12-bit A/D
Converter”
Changed the package code on “2. Packages”
Deleted pin function of “CEC0_1”.
*A
5208992
SHNA
04/07/2016
Corrected Current Rating.
Added the condition for CEC0_0, CEC1_0 and CEC1_1 to “Input Leak Current” on
“11.3.2 Pin Characteristics”.
Corrected the condition of Power supply shut down time on “11.4.7 Power-on
Reset Timing”.
Corrected the Part Number on “12. Ordering Information”.
Changed the package dimensions on “13.Package Dimensions”.
Document Number: 001-99223 Rev.*A
Page 128 of 129
S6E1B8 Series
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the
office closest to you, visit us at Cypress Locations.
Products
®
PSoC® Solutions
®
ARM Cortex Microcontrollers
Automotive
Clocks & Buffers
Interface
Lighting & Power Control
Memory
PSoC
Touch Sensing
USB Controllers
Wireless/RF
cypress.com/arm
cypress.com/automotive
cypress.com/clocks
cypress.com/interface
cypress.com/powerpsoc
cypress.com/memory
cypress.com/psoc
PSoC 1 | PSoC 3 | PSoC 4 | PSoC 5LP
Cypress Developer Community
Community | Forums | Blogs | Video | Training
Technical Support
cypress.com/support
cypress.com/psoc
cypress.com/touch
cypress.com/usb
cypress.com/wireless
ARM and Cortex are the registered trademarks of ARM Limited in the EU and other countries.
© Cypress Semiconductor Corporation, 2015-2016. This document is the property of Cypress Semiconductor Corporation and its subsidiaries, including Spansion LLC (“Cypress”). This document,
including any software or firmware included or referenced in this document (“Software”), is owned by Cypress under the intellectual property laws and treaties of the United States and other countries
worldwide. Cypress reserves all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or
other intellectual property rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of the Software,
then Cypress hereby grants you a personal, non-exclusive, nontransferable license (without the right to sublicense) (1) under its copyright rights in the Software (a) for Software provided in source
code form, to modify and reproduce the Software solely for use with Cypress hardware products, only internally within your organization, and (b) to distribute the Software in binary code form
externally to end users (either directly or indirectly through resellers and distributors), solely for use on Cypress hardware product units, and (2) under those claims of Cypress’s patents that are
infringed by the Software (as provided by Cypress, unmodified) to make, use, distribute, and import the Software solely for use with Cypress hardware products. Any other use, reproduction,
modification, translation, or compilation of the Software is prohibited.
TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE
OR ACCOMPANYING HARDWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. To the extent
permitted by applicable law, Cypress reserves the right to make changes to this document without further notice. Cypress does not assume any liability arising out of the application or use of any
product or circuit described in this document. Any information provided in this document, including any sample design information or programming code, is provided only for reference purposes. It
is the responsibility of the user of this document to properly design, program, and test the functionality and safety of any application made of this information and any resulting product. Cypress
products are not designed, intended, or authorized for use as critical components in systems designed or intended for the operation of weapons, weapons systems, nuclear installations, life-support
devices or systems, other medical devices or systems (including resuscitation equipment and surgical implants), pollution control or hazardous substances management, or other uses where the
failure of the device or system could cause personal injury, death, or property damage (“Unintended Uses”). A critical component is any component of a device or system whose failure to perform
can be reasonably expected to cause the failure of the device or system, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and you shall and hereby do release Cypress
from any claim, damage, or other liability arising from or related to all Unintended Uses of Cypress products. You shall indemnify and hold Cypress harmless from and against all claims, costs,
damages, and other liabilities, including claims for personal injury or death, arising from or related to any Unintended Uses of Cypress products.
Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, PSoC, CapSense, EZ-USB, F-RAM, and Traveo are trademarks or registered trademarks of Cypress in the
United States and other countries. For a more complete list of Cypress trademarks, visit cypress.com. Other names and brands may be claimed as property of their respective owners.
Document Number: 001-99223 Rev.*A
April 7, 2016
Page 129 of 129