Series 74 Convoluted Tubing 712-178 - Type A Straight, 45° & 90° Non-Environmental User-Installable Fitting for Series 74 Helical Convoluted Tubing 712 F S 178 M 16 20 - 6 1 TYPE A Do not use with PEEK convoluted tubing. See page D-16, part number 712-360. Style 1 or 2 Product Series Length in 1/2 inch (12.7) increments (Example: 6 = 3.0 inches (76.2)) Conn. Designator A, F, H, L, or S (Pages F-3 to F-5) Dash No. (Table III) Angular Function: K = 45° L = 90° S = Straight Shell Size (Table I) Finish (Table II) Basic No. LENGTH ± .060 (1.52) LENGTH ± .060 (1.52) A THREAD (Page F-17) TUBING C DIA (Page F-17) TUBING I.D. STRAIGHT STYLE 2 STRAIGHT .880 (22.4) MAX J DIA E G 45° F 45° 90° H STYLE 2 45° & 90° © 2003 Glenair, Inc. CAGE Codes 06324 Printed in U.S.A. GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912 www.glenair.com E-Mail: [email protected] D-14 Series 74 Convoluted Tubing 712-178 - Type A Straight, 45° & 90° Non-Environmental User-Installable Fitting for Series 74 Helical Convoluted Tubing SHELL SIZE A,F,L,S H 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 28 -32 -36 -- E MAX .639 (16.2) .664 (16.9) .688 (17.5) .705 (17.9) .732 (18.6) .748 (19.0) .773 (19.6) .800 (20.3) .823 (20.9) 1.041 (26.4) 1.092 (27.7) 1.138 (28.9) TABLE I F MAX .950 (24.1) .980 (24.9) 1.000 (25.4) 1.030 (26.2) 1.050 (26.7) 1.060 (26.9) 1.080 (27.4) 1.120 (28.4) 1.150 (29.2) 1.320 (33.5) 1.360 (34.5) 1.410 (35.8) TABLE II SYMBOL FINISH B Olive Drab over Cadmium Plate J Gold Iridite over Cadmium Plate over Nickel M Electroless Nickel N Olive Drab over Cadmium Plate over Nickel NC Zinc-Cobalt, Olive Drab NF Olive Drab over Cadmium Plate over Electroless Nickel (500 Hour Salt Spray) T Bright Dip Cadmium Plate over Nickel DASH NO. 06 09 10 12 14 16 20 24 28 32 40 48 56 64 G MAX .750 (19.1) .810 (20.6) .870 (22.1) .920 (23.4) .980 (24.9) 1.020 (25.9) 1.080 (27.4) 1.140 (29.0) 1.200 (30.5) 1.480 (37.6) 1.610 (40.9) 1.720 (43.7) H MAX 1.060 (26.9) 1.120 (28.4) 1.180 (30.0) 1.250 (31.8) 1.310 (33.3) 1.330 (33.8) 1.390 (35.3) 1.470 (37.3) 1.540 (39.1) 1.780 (45.2) 1.870 (47.5) 1.980 (50.3) TABLE III TUBING I.D. MIN MAX .181 (4.6) .188 (4.8) .273 (6.9) .281 (7.1) .306 (7.8) .312 (7.9) .364 (9.2) .375 (9.5) .427 (10.8) .437 (11.1) .485 (12.3) .500 (12.7) .608 (15.4) .625 (15.9) .730 (18.5) .750 (19.1) .860 (21.8) .875 (22.2) .975 (24.8) 1.000 (25.4) 1.210 (30.7) 1.250 (31.8) 1.437 (36.5) 1.500 (38.1) 1.688 (42.9) 1.750 (44.5) 1.937 (49.2) 2.000 (50.8) J MAX .720 (18.3) .821 (20.9) .852 (21.6) .915 (23.2) .977 (24.8) 1.040 (26.4) 1.165 (29.6) 1.290 (32.8) 1.415 (35.9) 1.540 (39.1) 1.790 (45.5) 2.040 (51.8) 2.290 (58.2) 2.540 (64.5) NOTES: 1. When tubing I.D. max exceeds inside diameter of connector shell, style 2 may be supplied. Refer to pages F-15 and F-16. 2. Metric dimensions (mm) are in parentheses. 3. Tubing shown for reference only. © 2003 Glenair, Inc. CAGE Codes 06324 Printed in U.S.A. GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912 www.glenair.com E-Mail: [email protected] D-15