SN8000/SN8000UFL Wi-Fi Module Datasheet Version: 1.0 11/25/2013 Note: Murata Electronics N.A, Inc (Murata) reserves the right to make changes in specifications at any time and without notice. The information furnished in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Murata for its use, nor any infringements of patents or other rights of third parties resulting from its use. No license is generated under any rights of Murata or its supporters unless specifically agreed. Murata Electronics N.A, Inc is a wholly owned subsidiary of Murata Manufacturing Compeny, Ltd. of Japan. Revision History Revision 1.0 Date 11/08/13 Author R. Willett 1.1 11/25/13 R Willett www.murata-ws.com Email: [email protected] ©2013 by Murata Change Description Initial version Removed SyChip logo; revised copyright notice; revised tech support information; deleted Chap 12 “Disclaimer;” deleted one referenced document, 1.4 – Reference, page 6; revised Table 14, page 20; Page 2 of 24 SN8000/SN8000UFL Wi-Fi Module Datasheet v1.0 -11/8/2013 Table of Contents 1 SYSTEM DESCRIPTIONS ..................................................................................................................................... 5 1.1 1.2 1.3 1.4 2 MECHANICAL SPECIFICATIONS ..................................................................................................................... 7 2.1 2.2 2.3 2.4 3 APPLICATIONS ........................................................................................................................................................ 5 BLOCK DIAGRAM ................................................................................................................................................... 6 ACRONYMS............................................................................................................................................................. 6 REFERENCE ............................................................................................................................................................ 6 MODULE DIMENSION (SN8000 / SN8000UFL)....................................................................................................... 7 MODULE TOP AND SIDE VIEW ................................................................................................................................. 7 PCB FOOTPRINT (TOP VIEW) ................................................................................................................................... 8 MODULE PIN-OUT................................................................................................................................................... 9 DC ELECTRICAL SPECIFICATIONS .............................................................................................................. 11 3.1 TYPICAL POWER CONSUMPTION........................................................................................................................... 11 3.2 POWER UP/DOWN SEQUENCE ............................................................................................................................... 12 3.3 GPIO INTERFACE ................................................................................................................................................. 12 3.4 SDIO INTERFACE ................................................................................................................................................. 13 3.4.1 SDIO Timing (Default Mode) ..................................................................................................................... 14 3.4.2 SDIO Timing (High Speed Mode) .............................................................................................................. 15 3.5 GSPI INTERFACE................................................................................................................................................... 16 4 RF SPECIFICATIONS .......................................................................................................................................... 17 4.1 4.2 4.3 DC/RF CHARACTERISTICS FOR IEEE 802.11B ..................................................................................................... 17 DC/RF CHARACTERISTICS FOR IEEE 802.11G ..................................................................................................... 18 DC/RF CHARACTERISTICS FOR IEEE 802.11N ..................................................................................................... 19 5 ANTENNA INFORMATION ................................................................................................................................ 20 6 ENVIRONMENTAL SPECIFICATIONS ........................................................................................................... 20 6.1 6.2 7 ABSOLUTE MAXIMUM RATINGS ............................................................................................................................ 20 RECOMMENDED OPERATING CONDITIONS ............................................................................................................ 20 PACKAGING AND MARKING INFORMATION ............................................................................................ 21 7.1 7.2 CARRIER TAPE DIMENSIONS ................................................................................................................................. 21 MODULE MARKING INFORMATION ....................................................................................................................... 22 8 ORDERING INFORMATION ............................................................................................................................. 22 9 ROHS DECLARATION ........................................................................................................................................ 22 10 REGULATORY INFORMATION ....................................................................................................................... 23 11 TECHNICAL SUPPORT CONTACT ................................................................................................................. 24 www.murata-ws.com Email: [email protected] ©2013 by Murata Page 3 of 24 SN8000/SN8000UFL Wi-Fi Module Datasheet v1.0 -11/8/2013 LIST OF FIGURES FIGURE 1 SN8000/8000UFL MODULE BLOCK DIAGRAM ..................................................................................................... 6 FIGURE 2 SN8000 TOP AND SIDE VIEW ............................................................................................................................... 7 FIGURE 3 SN8000UFL TOP AND SIDE VIEW ........................................................................................................................ 8 FIGURE 4 DETAILED PAD DIMENSIONS (FOR BOTH SN8000 AND SN8000UFL) (TOP VIEW) ................................................ 8 FIGURE 5 BOOT-UP SEQUENCE ........................................................................................................................................... 12 FIGURE 6 SDIO CONNECTION ............................................................................................................................................. 13 FIGURE 7 SDIO TIMING (DEFUALT MODE)......................................................................................................................... 14 FIGURE 8 SDIO TIMING (HIGH SPEED MODE) .................................................................................................................... 15 FIGURE 9 GSPI SIGNAL TIMING .......................................................................................................................................... 16 FIGURE 10 GSPI INTERFACE ............................................................................................................................................... 16 FIGURE 11 CARRIER TAPE DIMENSIONS ............................................................................................................................. 21 FIGURE 12 SN8000 PIN1 ORIENTATION .............................................................................................................................. 21 FIGURE 13 MODULE MARKING DETAIL .............................................................................................................................. 22 LIST OF TABLES TABLE 1 MODULE CONNECTOR SIGNAL DESCRIPTION ........................................................................................................ 9 TABLE 2 TYPICAL POWER CONSUMPTION FOR SN8000 ..................................................................................................... 11 TABLE 3 TYPICAL POWER CONSUMPTION FOR SN8000UFL.............................................................................................. 11 TABLE 4 DIGITAL I/O REQUIREMENTS ................................................................................................................................ 12 TABLE 5 SDIO PIN DESCRIPTION ....................................................................................................................................... 13 TABLE 6 SDIO INTERFACE TIMING DEFAULT ..................................................................................................................... 14 TABLE 7 SDIO TIMING - HIGH SPEED ................................................................................................................................. 15 TABLE 8 SDIO PIN DESCRIPTION – GSPI MODE ................................................................................................................. 16 TABLE 9 RF CHARACTERISTICS FOR IEEE 802.11B ............................................................................................................ 17 TABLE 10 RF CHARACTERISTICS FOR IEEE 802.11G.......................................................................................................... 18 TABLE 11 RF CHARACTERISTICS FOR IEEE 802.11N.......................................................................................................... 19 TABLE 12 EXTERNAL ANTENNA TO COMPLY WITH REGULATION (ONLY SN8000UFL) ...................................................... 20 TABLE 13 ABSOLUTE MAXIMUM RATING .......................................................................................................................... 20 TABLE 14 RECOMMENDED OPERATING CONDITIONS ......................................................................................................... 20 TABLE 15 ORDERING INFORMATION ................................................................................................................................... 22 www.murata-ws.com Email: [email protected] ©2013 by Murata Page 4 of 24 SN8000/SN8000UFL Wi-Fi Module Datasheet v1.0 -11/8/2013 1 System Descriptions SN8000/SN8000UFL 1.1 Applications The SN8000 is a certified 2.4 GHz IEEE 802.11b/g/n Wi-Fi module based on the Broadcom BCM43362 chipset. It is designed to fit indoor and outdoor sensor and control applications. The SN8000 integrates a Wi-Fi IC, RF front end, temperature compensated crystal (TCXO) and an on-board antenna. Wi-Fi Module The SN8000 is compatible with Broadcom WICED™ SDK software to support low power, low cost microcontroller platforms from STM32 ARM Cortex M3 and M4 families. The SN8000 module is an ideal solution for home automation, industrial control, Smart Energy, medical, and healthcare applications with or without cloud services. A footprint compatible version with U.FL connector, SN8000UFL, is also available for use with an external antenna. Module Summary 2.4GHz IEEE 802.11b/g/n radio technology Dimension: 24.0 mm × 11.4 mm × 2.0mm Antenna Configuration: On-board chip antenna or U.FL connector Transmit power: +18.5 dBm @ 802.11b Receive sensitivity: -96dBm Host interface: SDIO, SPI Operating temperature range: -40ºC to 85ºC RoHS2 compliant MSL Level 3 FCC/IC certified; ETSI compliant Compatible with Broadcom WICED™ SDK www.murata-ws.com Email: [email protected] ©2013 by Murata Page 5 of 24 SN8000/SN8000UFL Wi-Fi Module Datasheet v1.0 -11/8/2013 1.2 Block Diagram (for onboard antenna version) SN8000UFL VDD_BAT ANT LDO SDIO BCM43362 LPF SPI (802.11b/g/n) VDD_IO Sleep_CLK (Optional) SPDT (for UFL connector version) TCXO Figure 1 SN8000/8000UFL Module Block Diagram 1.3 Acronyms ISM Industrial, Scientific and Medical MAC Medium Access Control MSL Moisture Sensitivity Level PER Packet Error Rate ROHS Restriction of Hazardous Substances 1.4 SPI Serial Peripheral Interface SDIO Secure Digital Input Output Reference [1] SN8000/SN8000UFL Wi-Fi Module User Manual, Murata www.murata-ws.com Email: [email protected] ©2013 by Murata Page 6 of 24 SN8000/SN8000UFL Wi-Fi Module Datasheet v1.0 -11/8/2013 2 Mechanical Specifications 2.1 2.2 Module dimension (SN8000 / SN8000UFL) Parameter Typical Units Dimension (LxWxH) Dimension tolerances (LxWxH) 24.0 x 11.4 x 2.0 ±0.2/±0.2/±0.15 mm mm Module top and side view Figure 2 SN8000 Top and Side View www.murata-ws.com Email: [email protected] ©2013 by Murata Page 7 of 24 SN8000/SN8000UFL Wi-Fi Module Datasheet v1.0 -11/8/2013 Figure 3 SN8000UFL Top and Side View 2.3 PCB footprint (top view) Figure 4 Detailed Pad Dimensions (For both SN8000 and SN8000UFL) (top view) www.murata-ws.com Email: [email protected] ©2013 by Murata Page 8 of 24 SN8000/SN8000UFL Wi-Fi Module Datasheet v1.0 -11/8/2013 2.4 Module Pin-out Table 1 Module Connector Signal Description Pin # Pin name I/O - Description 1 GND 2 SDIO_D2 I/O 3 JTAG_TDI - JTAG_TDI, N/C otherwise. 4 JTAG_TDO - JTAG_TDO, N/C otherwise. 5 BTCX_FREQ/GPIO1 I/O GPIO/Coexistence output signal indicating Bluetooth transmission in restricted channel. Hi-Z at power-up and reset. 6 GPIO0 I/O GPIO/Strapping option for SDIO (pull low) or SPI mode (pull high). Has weak internal pull down. 7 ANT_SEL2 O Auxiliary antenna selection (RFSW_CONTROL3). Default low. 8 ANT_SEL1 O Main antenna selection (RFSW_CONTROL0). Default high. 9 GND - Ground 10 RST_N I Active low WLAN reset signal with internal 200K pull-down. 11 VDD_3V3_EN I Enables 3.3V LDO 12 VDD_BAT I Module power supply 13 GND - Ground 14 GND - Ground 15 GND - Ground 16 GND - Ground 17 GND - Ground 18 GND - Ground 19 GND - Ground 20 GND - Ground 21 GND - Ground 22 GND - Ground 23 GND - Ground 24 GND - Ground 25 GND - Ground 26 GND - Ground www.murata-ws.com Email: [email protected] ©2013 by Murata Ground SDIO data line 2 with internal weak pull-up that can be disabled. Page 9 of 24 SN8000/SN8000UFL Wi-Fi Module Datasheet v1.0 -11/8/2013 Pin # Pin name I/O 27 GND 28 BTCX_STATUS/GPIO4 I/O GPIO/Coexistence signal indicating Bluetooth priority status and TX/RX direction. Hi-Z at power-up and reset. 29 BTCX_TXCONF/GPIO3 I/O GPIO/Coexistence output giving Bluetooth permission to transmit. Hi-Z at power-up and reset. 30 BTCX_RF_ACTIVE/GPIO5 I/O GPIO/Coexistence signal indicating Bluetooth is active. Hi-Z at power-up and reset. 31 - Description SLEEP_CLK Ground I Optional external 32KHz sleep clock. Tie to GND if not used. 32 GND - Ground 33 VDD_IO I Power for IO and SDIO pads 34 SDIO_D1/SPI_IRQ I/O SDIO data line 1 with internal weak pull-up that can be disabled. 35 SDIO_D0/SPI_MISO I/O SDIO data line 0 with internal weak pull-up that can be disabled. 36 SDIO_CLK/ SPI_CLK I 37 SDIO_CMD/ SPI_MOSI SDIO/SPI clock. I/O SDIO command line with internal weak pull-up that can be disabled. I/O SDIO data line 3 with internal weak pull-up that can be disabled. 38 SDIO_D3/ SPI_CSX 39 GND - Ground 40 GND - Ground 41 GND - Ground 42 GND - Ground 43 GND - Ground 44 GND - Ground 45 JTAG_TCK - JTAG_TCK, N/C otherwise. 46 JTAG_TRSTN - JTAG_TRSTN, N/C otherwise. 47 JTAG_TMS - JTAG_TMS, N/C otherwise. 48 NC4 - No connect 49 GND - Ground www.murata-ws.com Email: [email protected] ©2013 by Murata Page 10 of 24 SN8000/SN8000UFL Wi-Fi Module Datasheet v1.0 -11/8/2013 3 DC Electrical Specifications 3.1 Typical Power Consumption Condition: 25°C, VDD_BAT=3.6V, VDD_IO= 3.6V Table 2 Typical Power Consumption for SN8000 Values Item Min Receive mode 11b 11n Typ Max 70 mA 315 mA 70 mA Transmit mode (14.5dBm/100 % Duty Cycle) 235 mA Receive mode 70 mA 225 mA Transmit mode (18.5dBm/100% Duty Cycle) 11Mbps Receive mode 11g Units Condition 54Mbps MCS7 Transmit mode (13.5dBm/100% Duty Cycle) Table 3 Typical Power Consumption for SN8000UFL Values Item Min Receive mode 11b 11n Max mA 285 mA 70 mA Transmit mode (14.5dBm/ 100 % Duty Cycle) 235 mA Receive mode 70 mA 225 mA Transmit mode (16.5dBm/100% Duty Cycle) 11Mbps 54Mbps MCS7 Transmit mode (13.5dBm/100% Duty Cycle) www.murata-ws.com Email: [email protected] ©2013 by Murata Typ 70 Receive mode 11g Units Condition Page 11 of 24 SN8000/SN8000UFL Wi-Fi Module Datasheet v1.0 -11/8/2013 3.2 Power Up/Down Sequence Figure 5 Boot-Up Sequence 3.3 GPIO Interface Five general purpose I/O (GPIO) pins are available on the SN8000 that can be used to connect to various external devices. GPIOs are tristated by default. Subsequently, they can be programmed to be either input or output pins via the GPIO control register. They can also be programmed to have internal pull-up or pulldown resistors. GPIO_0 is initially used as a strapping option to select between SDIO and SPI modes GPIOs 3, 4, and 5 are multiplexed with the Bluetooth Coexistence Interface. By default, these pins are BT_COEX pins. Software can reprogram these pins to behave as GPIOs. GPIO_1 is a GPIO by default, but can be programmed to become the BCTX_FREQ signal. Table 4 Digital I/O Requirements SYM Input low voltage (VDD_IO = 3.3V) Input high voltage (VDD_IO = 3.3V) ) Input low voltage (VDD_IO = 1.8V) Input high voltage (VDD_IO = 1.8V) VI VLIH VI VLIH Input low voltage (RESET pin) VIL Input high voltage (RESET pin) Output low voltage min. typ. max. unit - - 0.8 V 2.0 - VDD_IO V - - 0.7 V 1.1 - VDD_IO V - - 0.4 V VIH 1.08 - 3.6 V VOL VOH - - 0.4 V VDD_IO-0.4 - - V Input low current IIL - 0.3 - uA Input high current IIH - 0.3 - uA Output high voltage www.murata-ws.com Email: [email protected] ©2013 by Murata Page 12 of 24 SN8000/SN8000UFL Wi-Fi Module Datasheet v1.0 -11/8/2013 3.4 SDIO Interface Table 5 SDIO Pin Description No. Pin Name (i) SD 4-bit Mode (ii) SD 1-bit Mode 2 SDIO_D2 DATA2 Data line 2 NC Not used 34 SDIO_D1 DATA1 Data line 1 /Interrupt IRQ Interrupt 35 SDIO_D0 DATA0 Data line 0 DATA Data line 36 SDIO_CLK CLK Clock CLK Clock 37 SDIO_CMD CMD Command line CMD Command line 38 SDIO_D3 DATA3 Data line 3 NC Not used Figure 6 SDIO Connection www.murata-ws.com Email: [email protected] ©2013 by Murata Page 13 of 24 SN8000/SN8000UFL Wi-Fi Module Datasheet v1.0 -11/8/2013 3.4.1 SDIO Timing (Default Mode) Figure 7 SDIO Timing (Defualt Mode) Table 6 SDIO Interface Timing Default Parameter Clock CLK (All values are referred to min. VIH and max. VIL ©2013 by Murata Typ(1) Max(1) Unit (2) Frequency-Data Transfer Mode fPP Frequency-Identification Mode fOD Clock Low Time tWL Clock High Time tWH Clock Rise Time tTLH Clock Falling Time tTHL Inputs: CMD, DAT (referenced to CLK) Input Setup Time tISU Input Hold Time tIH Outputs: CMD, DAT (referenced to CLK) Output Delay time-Data Transfer Mode tODLY Output Delay time-Identification Mode tODLY (1). Timing is based on CL < 40pF load on CMD and Data. (2). Min (Vih) = 0.7*VDDIO and max (Vil) = 0.2*VDDIO. www.murata-ws.com Email: [email protected] Min(1) Symbol 0 0 10 10 - - 25 400 10 10 MHz kHz ns ns ns ns 5 5 - - ns ns 0 0 - 14 50 ns ns Page 14 of 24 SN8000/SN8000UFL Wi-Fi Module Datasheet v1.0 -11/8/2013 3.4.2 SDIO Timing (High Speed Mode) Figure 8 SDIO Timing (High Speed Mode) Table 7 SDIO Timing - High Speed Parameter Symbol Clock CLK (All values are referred to min. VIH and max. VIL(2) Frequency-Data Transfer Mode fPP Frequency-Identification Mode fOD Clock Low Time tWL Clock High Time tWH Clock Rise Time tTLH Clock Falling Time tTHL Inputs: CMD, DAT (referenced to CLK) Input Setup Time tISU Input Hold Time tIH Outputs: CMD, DAT (referenced to CLK) Output Delay time-Data Transfer Mode tODLY Output Hold time tOH Total System Capacitance (each line) CL (1). Timing is based on CL < 40pF load on CMD and Data. (2). Min (Vih) = 0.7*VDD_IO and max (Vil) = 0.2*VDD_IO. www.murata-ws.com Email: [email protected] ©2013 by Murata Min (1) Typ (1) Max(1) Unit 0 0 7 7 - - 50 400 3 3 MHz kHz ns ns ns ns 6 2 - - ns ns 2.5 - - 14 40 ns ns pF Page 15 of 24 SN8000/SN8000UFL Wi-Fi Module Datasheet v1.0 -11/8/2013 3.5 gSPI Interface The gSPI device always samples data on the rising edge of the clock. Figure 9 gSPI Signal Timing Table 8 SDIO Pin Description – gSPI Mode Pin gSPI Mode 2 NC Not used 34 IRQ Interrupt 35 DO Data output 36 SCLK Clock 37 DI Data Input 38 CS Card select gSPI Host SN8000 Figure 10 gSPI Interface www.murata-ws.com Email: [email protected] ©2013 by Murata Page 16 of 24 SN8000/SN8000UFL Wi-Fi Module Datasheet v1.0 -11/8/2013 4 RF Specifications 4.1 DC/RF Characteristics for IEEE 802.11b Conditions: 25deg.C, VDD_BAT=3.6V, VDD_IO= 3.3V (11Mbps mode unless otherwise specified.) Parameters measured at RF connector except EIRP Table 9 RF Characteristics for IEEE 802.11b Parameters Specification Modulation DSSS/CCK Physical layer data rate 1,2,5.5,11Mbps RF Characteristics Min Typ. Max. Unit Frequency range 2400 -- 2483.5 MHz -20 -- +20 ppm Carrier frequency error Transmit output power 1 Transmit power, EIRP SN8000UFL 15.0 17.0 SN8000 19.0 18.5 dBm dBm Spectrum mask 1st side lobes -- -- -30 dBr -- -- -50 dBr Power-on and Power-down ramp -- -- 2 usec RF Carrier Suppression 15 -- -- dBc Modulation accuracy (EVM) -- -- 35 % 30MHz to 1GHz (BW=100KHz) -96 dBm 1GHz to 12.75GHz (BW=1MHz) -41 dBm 1.8GHz to 1.9GHz (BW=1MHz) -65 dBm 5.15GHz to5.3GHz (BW=1MHz) -85 dBm nd 2 side lobes Outband spurious emissions 1 Receive Sensitivity 1Mbps (FER≤ 8%) -94 -96 -- dBm 11Mbps (FER≤ 8%) -86 -88 -- dBm Maximum input level (FER≤ 8%) -9.5 -- -- dBm Adjacent channel rejection (FER≤ 8%) 35 dB [Note] 1. Derate by 1.5 dB for temperatures less than -10 ºC or more than +55 ºC in both transmit and receive modes. www.murata-ws.com Email: [email protected] ©2013 by Murata Page 17 of 24 SN8000/SN8000UFL Wi-Fi Module Datasheet v1.0 -11/8/2013 4.2 DC/RF Characteristics for IEEE 802.11g Condition: 25deg.C, VDD_BAT=3.6V, VDD_IO= 3.3V (54Mbps mode unless otherwise specified.) Parameters measured at RF connector except EIRP Table 10 RF Characteristics for IEEE 802.11g Parameters Specification Standard conformance IEEE 802.11 g Modulation OFDM Data rate 6, 9, 12, 18, 24, 36, 48, 54Mbps RF Characteristics Min Typ. Max. Unit Frequency range 2400 -- 2483.5 MHz -20 -- +20 ppm 12.5 14.5 16.5 dBm Carrier frequency error Transmit output power 1 Transmit power, EIRP SN8000UFL SN8000 14.5 dBm Spectrum mask 9MHz to 11MHz (0dB ~ -20dB) 0 - dB 11MHz to 20MHz (-20dB ~ -28dB) 0 - dB 20MHz to 30MHz (-28dB ~ -40dB) 0 - dB 30MHz to 33MHz (-40dB) 0 - dB -25 dB 30MHz to 1GHz (BW=100KHz) -96 dBm 1GHz to 12.75GHz (BW=1MHz) -41 dBm 1.8GHz to 1.9GHz (BW=1MHz) -65 dBm 5.15GHz to5.3GHz (BW=1MHz) -85 dBm Constellation Error (EVM) -- -- Outband spurious emissions 1 Receive Sensitivity 6Mbps (PER≤ 10%) -87 -89 -- dBm 54Mbps (PER ≤ 10%) -72 -74 -- dBm Maximum input level (PER ≤ 10%) -13 -- -- dBm Adjacent channel rejection (PER ≤ 10%) -1 dB [Note] 1. Derate by 1.5 dB for temperatures less than -10 ºC or more than +55 ºC in both transmit and receive modes. www.murata-ws.com Email: [email protected] ©2013 by Murata Page 18 of 24 SN8000/SN8000UFL Wi-Fi Module Datasheet v1.0 -11/8/2013 4.3 DC/RF Characteristics for IEEE 802.11n Condition: 25deg.C, VDD_BAT=3.6V, VDD_IO= 3.3V (65Mbps mode unless otherwise specified.) Parameters measured at RF connector except EIRP Table 11 RF Characteristics for IEEE 802.11n Parameters Specification Standard conformance IEEE 802.11 n Modulation OFDM Data rate 6.5, 13, 19.5, 26, 39, 52, 58.5, 65Mbps RF Characteristics Min Typ. Max. Unit Frequency range 2400 -- 2483.5 MHz Carrier frequency error -20 -- +20 ppm 15.5 dBm Transmit output power 1 SN8000UFL Transmit power, EIRP SN8000 11.5 13.5 13.5 dBm Spectrum mask 9MHz to 11MHz (0dB ~ -20dB) 0 - dB 11MHz to 20MHz (-20dB ~ -28dB) 0 - dB 20MHz to 30MHz (-28dB ~ -45dB) 0 - dB 30MHz to 33MHz (-45dB) 0 - dB -28 dB 30MHz to 1GHz (BW=100KHz) -96 dBm 1GHz to 12.75GHz (BW=1MHz) -41 dBm 1.8GHz to 1.9GHz (BW=1MHz) -65 dBm 5.15GHz to5.3GHz (BW=1MHz) -85 dBm -- dBm Constellation Error (EVM) -- -- Outband spurious emissions 1 Receive Sensitivity 65Mbps (PER ≤ 10%) -69 -71 Maximum input level (PER ≤ 10%) -13 dBm Adjacent channel rejection (PER ≤ 10%) -2 dB [Note] 1. Derate by 1.5 dB for temperatures less than -10 ºC or more than +55 ºC in both transmit and receive modes. www.murata-ws.com Email: [email protected] ©2013 by Murata Page 19 of 24 SN8000/SN8000UFL Wi-Fi Module Datasheet v1.0 -11/8/2013 5 Antenna Information The table below shows the information of the reference antennae that are used in FCC, IC and ETSI testing for SN8000UFL. Table 12 External Antenna to comply with regulation (Only SN8000UFL) Part Number Vendor Gain (dBi) Antenna Type Connector TRF-1002 Microchip 5.0 Omnidirectional U.FL W1049B050 Pulse 2.0 Omnidirectional U.FL W3525B100 Pulse 2.0 Omnidirectional U.FL Remarks For FCC/IC compliance For FCC/IC and ETSI compliance For FCC/IC and ETSI compliance 6 Environmental Specifications 6.1 Absolute maximum ratings Table 13 Absolute Maximum Rating Symbol Description Min Max Unit Tsop Specification temperature -30 85 C Top* Operating temperature -40 85 C Tst Storage temperature -40 85 C VDD_IO IO Power supply 0 3.6 V VDD_BAT Power supply 0 5.0 V RFin RF input power 0 dBm MSL Moisture Sensitivity Level RoHS2 Restriction of Hazardous Substances 3 Compliant *Note: RF performance may be degraded at extreme temperatures. 6.2 Recommended Operating Conditions Table 14 Recommended Operating Conditions VDD_IO VDD_BAT Min (V) 1.75 Typ (V) 3.3 Max (V) 3.6 3.0 3.6 5.0 www.murata-ws.com Email: [email protected] ©2013 by Murata Description Supply to the IO pads Supply to BCM43362 BB/MAC/RF Page 20 of 24 SN8000/SN8000UFL Wi-Fi Module Datasheet v1.0 -11/8/2013 7 Packaging and Marking Information 7.1 Carrier Tape Dimensions Figure 11 Carrier Tape Dimensions Figure 12 SN8000 Pin1 Orientation www.murata-ws.com Email: [email protected] ©2013 by Murata Page 21 of 24 SN8000/SN8000UFL Wi-Fi Module Datasheet v1.0 -11/8/2013 7.2 Module Marking Information Module Marking for SN8000 Module Marking for SN8000UFL Figure 13 Module Marking Detail 8 Ordering Information Table 15 Ordering Information Product SN8000 Evaluation Development Kit SN8000 Module in Tape & Reel SN8000UFL Evaluation Development Kit SN8000UFL Module in Tape & Reel RFM Model Number RFM Part Number Standard Order Increment SN8000EVK 88-00153-85 1 pc SN8000 88-00153-00 400 pcs/reel SN8000UFL EVK 88-00153-87 1 pc SN8000UFL 88-00153-02 400 pcs/reel 9 RoHS Declaration To the best of our present knowledge, given our supplier declarations, this product does not contain substances that are banned by Directive 2011/65/EU or contain a maximum concentration of 0.1% by weight in homogeneous materials for Lead and lead compounds Mercury and mercury compounds Chromium (VI) PBB (polybrominated biphenyl) PBDE (polybrominated biphenyl ether) And a maximum concentration of 0.01% by weight in homogeneous materials for Cadmium and cadmium compounds www.murata-ws.com Email: [email protected] ©2013 by Murata Page 22 of 24 SN8000/SN8000UFL Wi-Fi Module Datasheet v1.0 -11/8/2013 10 Regulatory Information The table below shows the regulatory compliance status of the SN8000/8000UFL module. Regulatory Body Standard FCC Part 15 IC RSS-210 ETSI EN300 328, Ver. 1.8.1 ETSI EN301.489 - 17 Certificate ID QPU8000 4523A-SN8000 Compliant For more information, see SN8000/SN8000UFL Wi-Fi Module User Manual [2]. www.murata-ws.com Email: [email protected] ©2013 by Murata Page 23 of 24 SN8000/SN8000UFL Wi-Fi Module Datasheet v1.0 -11/8/2013 11 Technical Support Contact For technical support, please contact us at [email protected]. Murata Electronics N.A., Inc. 4441 Sigma Road Dallas, TX 75244 USA www.murata-ws.com Email: [email protected] ©2013 by Murata Page 24 of 24 SN8000/SN8000UFL Wi-Fi Module Datasheet v1.0 -11/8/2013