MITSUMI HBS-Compatible Driver and Receiver with Power Supply MM1034 HBS-Compatible Driver and Receiver with Power Supply Monolithic IC MM1034 Outline This IC conforms to the HBS (Home Bus) specification (Electronic Industries Association of Japan), and has functions for the reception and transmission of data. It incorporates power supply circuitry which employs an efficient switching regulator, and so can draw power directly from the bus line. AMI is adopted for the waveforms of signals handled by the transmission and reception units, designed for connection to twisted-pair lines. Telephone equipment, security devices, audio or video equipment, air-conditioning equipment, and a wide range of other devices can be connected to a bus line to enable mutual communications. Features 1. Compact design 2. High reliability 3. Replaces pulse transformers 4. Low cost 5. Adopts highly efficient switching regulator 6. Easy circuit design 7. Stable internal power supply circuit (Vo1=5 V ±0.25) 8. Few external components Applications 1. Telephony equipment 2. Security equipment 3. Audio and video devices 4. Air-conditioning equipment 5. Wide range of other equipment and devices Package DIP-16A (MM1034XD) SOP-16A (MM1034XF) Block diagram HBS-Compatible Driver and Receiver with Power Supply MM1034 MITSUMI Absolute Maximun Ratings (Ta=25°C) Item Symbol Ratings Units Storage temperature TSTG -40~+125 °C Operating temperature TOPR -20~+75 °C Power supply current VCC max. -0.3~+46 V Operating power supply voltage VCCOP 13~45 V Allowable loss Pd 400 mW Electrical Characteristics (Except where noted therwise, Ta=25°C, VCC=30V, Ftransmit=10kHz (DUTY=50%)) Item Symbol Measurement conditions Min. Typ. Output voltage VO1 VCC1=15~45V, IL=0~250mA 4.75 5.00 Output voltage VO2 VCC1=13~45V, IL=0~250mA 4.70 5.00 Output voltage VO2 VCC1=11~45V, IL=0~100mA 4.75 5.00 Output ripple voltage Vr IL=250mA, no spikes Reactive current ICCO IL=0mA, transmit unit off 4 SWR transmission FOSC SWR 80 frequency Power supply current IIS RS=0.2Ω 7.5 on short-circuit Output current IOS RS=0.2Ω 70 110 on short-circuit Transmission output voltage VTO Both pins 8 and 9 3.8 4.2 Transmission VTR VTO1/VTO2 0.75 1.0 waveform symmetry Reception sensitivity VRS 0.65 0.75 Noise resistance VRN Level at which no errors are output 0.55 Input impedance RIN Both pins 11 and 12 25 36 Transmission delay time 1 Td1 cf. transmit/receive waveform diagrams 0.2 Transmission Transmission delay time 2 Td2 cf. transmit/receive waveform diagrams 0.4 circuit Transmission delay time 3 Td3 cf. transmit/receive waveform diagrams 0.7 Transmission delay time 4 Td4 cf. transmit/receive waveform diagrams 1.0 Reception output H voltage VROH 4.5 Reception output L voltage VROL Transmission waveform LOSS 1 VTLS VT=5V applied, power on 4.5 Transmission waveform LOSS 2 VTLS applied, power off 4.5 H level input voltage VLIH 2.4 L level input voltage VLIL H level input current ILIH VIN=2.4V L level input current ILIL VIN=0.4V Max. Units 5.25 V 5.25 V 5.25 V 50 mV 6 mA kHz 12 mA 150 mA 4.6 VP-P 1.25 0.85 46 0.5 0.8 10 300 VP-P VP-P kΩ µS µS µS µS V V V V V V µA µA When a negative voltage is applied to pins 8 and 9, there should be no abnormal operation of internal circuits between 0 and 6V. However, if a negative voltage exceeding -6V is applied, thyristor operation may result, so it is recommended that an external clamping diode be added. MITSUMI Measuring Circuit Measurement circuit 1 Measurement circuit 2 HBS-Compatible Driver and Receiver with Power Supply MM1034 HBS-Compatible Driver and Receiver with Power Supply MM1034 MITSUMI Application Circuits DATA IN A DATA IN B Transmission DATA OUT A Transmission DATA OUT B Reception DATA OUT Additional Application Circuits (SWR circuit not used) Even when a 5V external voltage can be supplied, an addition voltage of 13 to 45V must be applied to pins 2 and 3 in order to obtain an internal biased power supply of 3.4V. HBS-Compatible Driver and Receiver with Power Supply MM1034 MITSUMI Circuit Diagram Characteristics VOUT vs. VIN VOUT vs. IO 5.10 5.10 When shorted by 0.2Ω (no power supply limiter resistance) IO (mA) 5.00 0 50 100 200 300 30V VCC 20V VOUT (V) VOUT (V) 5.00 4.90 15V 10V 4.90 4.80 4.80 10 20 VIN (V) 30 40 100 200 IO (mA) 300 400 HBS-Compatible Driver and Receiver with Power Supply MM1034 MITSUMI Iccq-Temp. 52 12 51 10 Icco (mA) VOUT (V) VOUT-Temp. 50 49 48 47 8 6 4 2 -20 0 20 40 0 -20 60 0 Ta (°C) Ta 6 120 5 110 4 IIN IOUT 2 1 0 100 200 300 400 500 100 90 80 -20 40 60 Output ripple-Temperature Icc (IL.250mA) -Temp. 60 100 50 80 IL=250mA 60 IL=0 40 30 40 20 20 10 0 20 Ta 40 0 -20 60 0 20 40 60 Ta (°C) (°C) Sens. (Receiver) -Temp. Vo (Transmit) -Temp. 2.0 VRS (Vp-p) 4.8 4.6 4.4 4.2 4.0 1.8 1.6 1.4 1.2 1.0 With 33kΩ 2 inserted 0.8 0.6 3.8 -20 20 Ta (°C) 120 0 -20 0 IIN IOUT (mA) ICC (mA) VOR (mV) 60 0 0 VIO (Vp-p) 40 (°C) OSC Freg.-Temp. FOSC (kHz) VOUT (V) Over Current Protect Charac. Rs-0.2Ω 3 20 0 20 Ta 40 (°C) 60 -20 0 40 20 Ta (°C) 60