CMF (Military RN and RL) www.vishay.com Vishay Dale Metal Film Resistors, Military, MIL-R-10509 Qualified, Precision, Type RN and MIL-PRF-22684 Qualified, Type RL FEATURES • Very low noise (- 40 dB) • Very low voltage coefficient (5 ppm/V) • Controlled temperature coefficient • Flame retardant epoxy coating • Commercial alternatives to military styles are available with higher power ratings. See CMF Industrial data sheet: (www.vishay.com/doc?31018) STANDARD ELECTRICAL SPECIFICATIONS RESISTANCE RESISTANCE RESISTANCE RANGE RANGE RESISTANCE MAX. RANGE POWER POWER MIL DIELECTRIC RANGE GLOBAL MIL RATING RATING WORKING TOL. (3) SPEC. STRENGTH MODEL STYLE P70 °C P125 °C VOLTAGE (1) MIL-R-10509 MIL-R-10509 MIL-R-10509 ±% SHEET VAC ± 100 ppm/°C ± 50 ppm/°C ± 25 ppm/°C MIL-PRF-22684 W W V (D) (C) (E) CMF50 RN50 08 - 0.05 200 - 10 to 100K 10 to 100K - 0.1, 0.25, 0.5, 1 450 CMF55 RN55 07 0.125 0.10 200 10 to 301K 49.9 to 100K 49.9 to 100K - 0.1, 0.25, 0.5, 1 450 CMF60 RN60 01 0.25 0.125 300 10 to 1M 49.9 to 499K 49.9 to 499K - 0.1, 0.25, 0.5, 1 500 CMF65 RN65 02 0.50 0.25 350 10 to 2M 49.9 to 1M 49.9 to 1M - 0.1, 0.25, 0.5, 1 900 CMF70 RN70 03 0.75 (2) 0.50 500 10 to 2.49M 24.9 to 1M 24.9 to 1M - 0.1, 0.25, 0.5, 1 900 CMF07 RL07 01 0.25 - 250 - - - 51 to 150K 2, 5 450 CMF20 RL20 02 0.50 - 350 - - - 4.3 to 470K 2, 5 700 Notes (1) Continuous working voltage shall be P x R or maximum working voltage, whichever is less. (2) Formerly rated at 1 W and is the direct replacement for RN70 of MIL-R-10509 rev. D. (3) Tolerances of ± 0.1 %, ± 0.25 % and ± 0.5 % are not applicable to characteristic D. TECHNICAL SPECIFICATIONS PARAMETER UNIT CONDITION ppm/V 5 when measured between 10 % and full rated voltage Insulation Resistance 1010 min. dry; 108 min. after moisture test Operating Temperature Range °C - 65/+ 175 (see derating curves for military range) Terminal Strength Ib 5 pound pull test for RL07/RL20; 2 pound pull test for all others Voltage Coefficient Solderability Revision: 02-May-13 Continuous satisfactory coverage when tested in accordance with MIL-R-10509 and MIL-PRF-22684 Document Number: 31027 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 CMF (Military RN and RL) www.vishay.com Vishay Dale GLOBAL PART NUMBER INFORMATION New Global Part Numbering: RN60D3483FR36 (preferred part numbering format) R MIL STYLE N 6 0 3 4 8 RESISTANCE VALUE 3 digit significant figure, followed by a multiplier Use “R” for values < 100 Ω 10R0 = 10 Ω 2152 = 21.5 k Ω 2494 = 2.49 M Ω CHARACTERISTIC RN50 RN55 RN60 RN65 RN70 D E = 25 ppm C = 50 ppm D = 100 ppm 3 F R TOLERANCE CODE B = ± 0.1 % C = ± 0.25 % D = ± 0.5 % F=±1% 3 6 PACKAGING SPECIAL Blank = Standard B14 = Tin/lead, bulk (Dash number) BSL = Tin/lead, bulk, 88 = Hot solder dip single lot date code 143 = Non-magnetic R36 = Tin/lead, T/R (full) RE6 = Tin/lead, T/R (1000 pieces) RSL = Tin/lead, T/R, single lot date code Historical Part Number example: RN60D3483F (will continue to be accepted) RN60 MIL STYLE D 3483 F CHARACTERISTIC RESISTANCE VALUE TOLERANCE CODE R36 PACKAGING New Global Part Numbering: RL07S471JR36 (preferred part numbering format) R L 0 MIL STYLE LEAD MATERIAL RL07 RL20 S = Solderable 7 S 4 7 1 J R 3 6 RESISTANCE TOLERANCE PACKAGING SPECIAL VALUE CODE 2 digit significant G=±2% B14 = Tin/lead, bulk Blank = Standard figure, followed by BSL = Tin/lead, bulk, single lot date code (Dash number) J=±5% a multiplier R36 = Tin/lead, T/R (full) 88 = Hot solder dip Use “R” for RE6 = Tin/lead, T/R (1000 pieces) 143 = Non-magnetic values < 10 Ω RSL = Tin/lead, T/R, single lot date code 4R3 = 4.3 Ω 202 = 2.0 k Ω 474 = 470 k Ω Historical Part Number example: RL07S471J (will continue to be accepted) RL07 S 471 J MIL STYLE LEAD MATERIAL RESISTANCE VALUE TOLERANCE CODE R36 PACKAGING Note • For additional information on packaging, refer to the Through Hole Resistor Packaging document (www.vishay.com/doc?31544). MATERIAL SPECIFICATIONS Element Nickel-chrome alloy Coating Flame retardant epoxy, formulated for superior moisture protection Core Termination CAGE CODE: 91637 Fire-cleaned high purity ceramic Standard lead material is solder-coated copper. Solderable and weldable. ENVIRONMENTAL SPECIFICATIONS General APPLICABLE MIL-SPECS MIL-R-10509 and MIL-PRF-22684: The CMF models meet or exceed the electrical, environmental and dimensional requirements of MIL-R-10509 and MIL-PRF-22684. Shelf Life Environmental performance is shown in the Environmental Performance table. Test methods are those specified in MIL-R-10509 and MIL-PRF-22684. Resistance shifts due to storage at room temperature are negligible. Noise: Vishay Dale metal film resistors have exceptionally low noise level. Average for standard resistance range is 0.10 μV per V over a decade of frequency, with low and intermediate resistance values typically below 0.05 μV per V. Revision: 02-May-13 Document Number: 31027 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 CMF (Military RN and RL) www.vishay.com Vishay Dale % OF RATED POWER Vishay Dale CMF resistors have an operating temperature range of - 65 °C to + 175 °C. They must be derated according to the following curves: 120 100 MIL-R-10509 Char. C and E Rating MIL-R-10509 Char. D Rating 80 60 40 20 MIL-PRF-22684 0 50 70 90 110 130 150 170 AMBIENT TEMPERATURE °C DERATING DIMENSIONS in inches (millimeters) 1.50 ± 0.125 (1) (38.10 ± 3.18) A D C (Max.) VISHAY DALE MODEL B A B C (MAX.) D CMF50 0.150 ± 0.020 (3.81 ± 0.51) 0.065 ± 0.015 (1.65 ± 0.38) 0.244 (6.20) 0.016 ± 0.002 (0.41 ± 0.05) CMF55 0.240 ± 0.020 (6.10 ± 0.51) 0.090 ± 0.008 (2.29 ± 0.20) 0.290 (7.37) 0.025 ± 0.002 (0.64 ± 0.05) CMF60 0.344 ± 0.031 (8.74 ± 0.79) 0.145 ± 0.015 (3.68 ± 0.38) 0.425 (10.80) 0.025 ± 0.002 (0.64 ± 0.05) CMF65 0.562 ± 0.031 (14.27 ± 0.79) 0.180 ± 0.015 (4.57 ± 0.38) 0.687 (17.45) 0.025 ± 0.002 (0.64 ± 0.05) CMF70 0.562 ± 0.031 (14.27 ± 0.79) 0.180 ± 0.015 (4.57 ± 0.38) 0.687 (17.45) 0.032 ± 0.002 (0.81 ± 0.05) CMF07 0.240 ± 0.020 (6.10 ± 0.51) 0.090 ± 0.008 (2.29 ± 0.20) 0.290 (7.37) 0.025 ± 0.002 (0.64 ± 0.05) CMF20 0.375± 0.040 (9.53 ± 1.02) 0.145 ± 0.015 (3.68 ± 0.38) 0.425 (10.80) 0.032 ± 0.002 (0.81 ± 0.05) Notes (1) Lead length for product in bulk pack. For product supplied in Tape and Reel, the actual lead length would be based on the body size, tape spacing and lead trim. MILITARY POWER RATING MILITARY QUALIFIED MIL-R-10509 WATTAGE MIL-PRF-22684 AT + 70 °C (D) AT + 125 °C (C and E) AT + 70 °C 0.05 - RN50 - 0.10 - RN55 - 0.125 RN55 RN60 - 0.25 RN60 RN65 RL07 0.50 RN65 RN70 RL20 0.75 (2) RN70 - - Notes • Commercial equivalents of military styles are available with higher power ratings. Consult factory. (2) Formerly rated at 1 W and is the direct replacement for RN70 of MIL-R-10509 rev. D. Revision: 02-May-13 Document Number: 31027 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 CMF (Military RN and RL) HEAT RISE (°C ABOVE AMBIENT) www.vishay.com Vishay Dale 120 CMF50 100 CMF55 CMF07 CMF60 CMF20 80 CMF65, CMF70 60 40 20 0 0 0.125 0.25 0.375 0.5 0.625 THERMAL RESISTANCE 0.75 0.875 1 1.125 APPLIED POWER IN W MARKING (per MIL-PRF-10509) Characteristics: D = 100 ppm, C = 50 ppm, E = 25 ppm Tolerance: F = 1 %, D = 0.5 %, C = 0.25 %, B = 0.1 % Value = Three significant figures and multiplier J = JAN (Joint Army - Navy) brand RN50: (3 lines) J50D 1211 F137 RN55, RN60, RN65, RN70 (4 lines) DALE 0137J RN55D 1211F JAN, type, characteristic Value Tolerance and 3 digit date code Company logo 4 digit date code and JAN brand Type and characteristic Value and Tolerance Note • RL series are color banded per MIL-PRF-22684. PERFROMANCE REQUIREMENT MIL-R-10509 MIL-PRF-22684 CHARACTERISTIC D CHARACTERISTIC C CHARACTERISTIC E + 200 ppm/°C - 500 ppm/°C ± 50 ppm/°C ± 25 ppm/°C ± 200 ppm/°C ± 100 ppm/°C ± 50 ppm/°C ± 25 ppm/°C ± 200 ppm/°C MILmax. MILmax. MILmax. MILmax. Thermal Shock ± 0.50 % R ± 0.25 % R ± 0.25 % R ± 1.00 % R Short Time Overload ± 0.50 % R ± 0.25 % R ± 0.25 % R ± 0.50 % R Low Temperature Operation ± 0.50 % R ± 0.25 % R ± 0.25 % R ± 0.50 % R Moisture Resistance ± 1.50 % R ± 0.50 % R ± 0.50 % R ± 1.50 % R Shock ± 0.50 % R ± 0.25 % R ± 0.25 % R ± 0.50 % R Vibration ± 0.50 % R ± 0.25 % R ± 0.25 % R ± 0.50 % R Load Life ± 1.00 % R ± 0.50 % R ± 0.50 % R ± 2.00 % R Dielectric Withstanding Voltage ± 0.50 % R ± 0.25 % R ± 0.25 % R ± 0.50 % R Effect of Solder ± 0.50 % R ± 0.10 % R ± 0.10 % R ± 0.50 % R MIL Temperature Coefficient Applicable Vishay Dale Temperature Coefficient TEST Revision: 02-May-13 Document Number: 31027 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000