RESISTORS RESISTOR NETWORK SIL Low-profile Epoxy dipped 5 to 13-pin The Dubilier range of SIL networks features 2% accuracy in a lowcost package. The low-profile epoxy package allows the device to be used in locations where moulded parts do not fit. Isolated and common-terminal designs are available, allowing the simple, reliable insertion of up to 12 resistors at once. OUTLINE DRAWING 2.5 max L max PIN 1 Marking 9E-103G 5.2 max 3.0 ± 0.5 0.5 ± 0.1 3.0 ± 0.1 No of Pins L max SECTION 4 2.54 ± 0.25 5 6 7 8 9 10 11 12 13 12.7 15.3 17.8 20.4 22.9 25.4 28.0 30.5 33.1 RANGE & TOLERANCES Parameter Power Rating per Element Temperature Range Resistance Range Resistance Tolerance Temperature Coefficient Max Working Voltage Max Overload Voltage Performance Limits 0.125W @ 70°C -55˚ to +125°C Derating linearly from 70°C 33Ω to 1MΩ E - 24 series ± 2% (G) ± 100 ppm/°C 50Ω ≥ 2.2MΩ ± 250ppm/˚C <50Ω – 2.2MΩ 100V 200V ORDERING INFORMATION 9 E N° Pins Type 103 Value Tolerance G 5 to 13 M = Isolated E = Common 3 digit code : Last digit is decade multiplier. First two digits are first digits of value. 2% 135 Fax: 01371 875075 www.dubilier.co.uk Tel: 01371 875758 RESISTORS RESISTOR NETWORK SIL SPECIFICATION SECTION 4 Short Term Overload Vibration Dielectric Strength Solderability ∆R/R ± (1% + 0.05Ω) After application of 21/2 x rated voltage, or the maximum overload voltage, whichever smaller, for a period of 5 secs. Resistance change to be within specification, with no evidence of arcing, burning or charring. ∆R/R ± (0.5% + 0.5Ω) Resistors are to be subjected to vibration of amplitude 0.8mm for 2 hours in each of three mutually perpendicular directions. The vibration frequency shall be swept from 10 to 55 to 10Hz in 1 minute. Resistance change to be within specification with no evidence of damage. Components shall withstand twice their rated voltage for 1 minute applied between termination and substrate. No evidence of arcing, burning or charring. ∆R/R ± (1% + 0.05Ω) After dipping at 260°C ± 5°C for 10 seconds, resistance change to be within specification, with no evidence of Load Life Moisture Load Voltage Coefficient Flammability arcing, burning or charring. Terminations shall maintain a minimum of 75% coverage following the procedures of MIL-STD-202E. ∆R/R ± (2% + 0.05Ω) After 1000 hours application of the rated voltage with a duty cycle of 11/2 hours ON and 1/2 hour OFF, at 70°C. Resistance change to be within specification, with no evidence of arcing, burning or charring. ∆R/R ± (2% + 0.05Ω) After 1000 hours application of the rated voltage with a duty cycle of 11/2 hours ON and 1/2 hour OFF, at 40°C and 90-95% RH. Resistance change to be within specification, with no evidence of arcing, burning or charring. ∆R/R < 100ppm/V Product is conformally coated with epoxy resin conforming to UL94V-0. SIL PIN-OUTS Common (E) 1 2 Common parts are characterised by having a number of resistive elements, all of the same nominal value. All elements are connected to pin 1. 3 6 4 5 n = Number of pins 7 8 n-1 Isolated (M) 1 2 Isolated parts are characterised by having a number of resistive elements, all of the same nominal value. All elements are independent. 3 4 6 5 n = Number of pins n-1 n 136 Fax: 01371 875075 www.dubilier.co.uk Tel: 01371 875758