3. FINISH SPECIFICATIONS: STAINLESS STEEL PARTS: PASSIVATE CONTACTS: .000100 MIN GOLD PER ASTM B488 OVER .000080 MIN NICKEL PER AMS-QQN-290 (RoHS) CRIMP SLEEVE: .000100 MIN NICKEL PER AMS-QQ-N-290 OVER COPPER FLASH PER ASTM B734 (RoHS) 4. ELECTRICAL SPECIFICATIONS: LOW VOLTAGE CONTACTS: 42 - 60 VAC, 1 AMP AUX ELECTRICAL CONTACTS: 600 VAC, 10 AMP 6. OPTICAL: WAVELENGTH: 1100nm - 1350nm INSERTION LOSS: 0.3dB TYPICAL, 0.5dB MAX RETURN LOSS: > -45dB, -50dB TYPICAL DESCRIPTION BY APPD DATE D REVISED PER ER30231 xxx 2. MATERIAL SPECIFICATIONS: CONTACTS: COPPER ALLOY ALIGNMENT PINS: BRASS PER ASTM B16 CRIMP SLEEVE: PHOS. BRONZE O-RINGS AND STRAIN RELIEF: SILICONE RUBBER ALL PLASTIC PARTS: 20% GLASS FILLED POLYPROPYLENE ALL OTHER METAL PARTS: 303 STAINLESS STEEL PER ASTM A582 REV KFC 01/06/10 NOTES: UNLESS OTHERWISE SPECIFIED 1. INTERFACE COMPLIANT TO SMPTE 304 SPECIFICATION. 7. REPLACEMENT KITS: CONTACT KIT: 7760-000-00702Z 8. CABLE PREPARATION AND STRIPPING PROCEDURE: CAP-E05. 9. OPTIONAL ENVIRONMENTAL BOOT 7760-000-00705Z SOLD SEPARATELY. 10. RED LDPE DUST CAP INCLUDED (NOT SHOWN) 11. CRIMP TOOLING: FOR FACTORY APPLICATION USE HAND TOOL KTH-1000 AND DIE KTH-2035 FOR FIELD APPLICATION USE HAND TOOL KTH-5000 AND DIE KTH-5018 5. ENVIRONMENTAL: OPERATING TEMPERATURE RATING: -40°C TO 75°C NON-OPERATING/STORAGE TEMPERTURE RATING: -40°C TO 85°C HUMIDITY: <95 RH (AT 40°C) 5.254 133.45 .804 20.42 .905 22.99 3/4" WRENCH FLATS (180° APART) 9/16" WRENCH FLATS (180° APART) MARK PER ES-781: 7763-3-3 (DATE CODE) CATALOG P/N: 7763-3-3 PER ASME Y14.5M-1994 UNLESS OTHERWISE SPECIFIED: DIMENSIONS ARE IN INCHES [MM] TOLERANCES: DECIMAL: .XX [X.X] ± .01 [0.3] .XXX [X.XX] ± .005 [0.13] .XXXX [X.XXX] ± .XXXX ANGLES: ± 2° SCALE: 1:1 THIRD ANGLE CUSTOMER SALES DRAWING DRAWN PSM APPROVED WPM DMF026 B DATE APPROVED 03/25/09 RL DATE APPROVED 08/03/09 JCF Winchester Electronics Corporation 62 Barnes Industrial Road North Wallingford, Connecticut 06492 TRI-LOC, SMPTE 304, RECEPTACLE DATE 08/03/09 DATE 01/19/10 A SD7763-3-3 SHT OF 1 2 REV D DESCRIPTION BY APPD DATE D REVISED PER ER30231 KFC 01/06/11 XXX REV REPLACEMENT COMPONENT ORDERING NUMBERS 11 8 4 3 2 1 5 10 9 6 7 12 12 VNSC-748U RED LDPE PROTECTIVE CAP, .906" ID 25 11 78-0102U #4-40 HEX SET SCREW 10 10 9 8 7 6 5 4 3 2 1 78-1012U 78-3011U 78-3010U 78-7016U 78-4204U 78-4203U 78-0705U 78-0701U 78-0301U 1-8156U STRENGTH MEMBER SUPPORT CLAMP JACK INSULATOR HALF SIDE "A" JACK INSULATOR HALF SIDE "B" TERMINI FOR MANUAL POLISH W/PROT. CAP JACK MALE CRIMP CONTACT JACK FEMALE CRIMP CONTACT REAR O-RING REAR CABLE SEAL WASHER FOR REAR CABLE SEAL CRIMP SLEEVE (CABLE SHIELD FERRULE) 10 25 25 10 50 50 25 25 25 25 ITEM NO. DMF026 B PART NO. Description QTY. CATALOG P/N: 7763-3-3 PER ASME Y14.5M-1994 UNLESS OTHERWISE SPECIFIED: DIMENSIONS ARE IN INCHES [MM] TOLERANCES: DECIMAL: .XX [X.X] ± .01 [0.3] .XXX [X.XX] ± .005 [0.13] .XXXX [X.XXX] ± .XXXX ANGLES: ± 2° SCALE: 1:1 THIRD ANGLE CUSTOMER SALES DRAWING DRAWN PSM APPROVED WPM DATE APPROVED 03/25/09 RL DATE APPROVED 08/03/09 JCF Winchester Electronics Corporation 62 Barnes Industrial Road North Wallingford, Connecticut 06492 TRI-LOC, SMPTE 304, RECEPTACLE DATE 08/03/09 DATE 01/19/10 A SD7763-3-3 SHT OF 2 2 REV D