Revised August 1999 74F563 Octal D-Type Latch with 3-STATE Outputs General Description Features The 74F563 is a high-speed octal latch with buffered common Latch Enable (LE) and buffered common Output Enable (OE) inputs. ■ Inputs and outputs on opposite sides of package allowing easy interface with microprocessors This device is functionally identical to the 74F573, but has inverted outputs. ■ Functionally identical to 74F573 ■ Useful as input or output port for microprocessors Ordering Code: Order Number Package Number Package Description 74F563SC M20B 20-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-013, 0.300 Wide 74F563SJ M20D 20-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide 74F563PC N20A 20-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300 Wide Devices also available in Tape and Reel. Specify by appending the suffix letter “X” to the ordering code. Logic Symbols Connection Diagram IEEE/IEC © 1999 Fairchild Semiconductor Corporation DS009562 www.fairchildsemi.com 74F563 Octal D-Type Latch with 3-STATE Outputs April 1988 74F563 Unit Loading/Fan Out Pin Names Description U.L. Input IIH/IIL HIGH/LOW Output IOH/IOL D0–D7 Data Inputs 1.0/1.0 20 µA/−0.6 mA LE Latch Enable Input (Active HIGH) 1.0/1.0 20 µA/−0.6 mA OE 3-STATE Output Enable Input (Active LOW) O0–O7 3-STATE Latch Outputs 1.0/1.0 20 µA/−0.6 mA 150/40 (33.3) −3 mA/24 mA (20 mA) Function Table Functional Description The 74F563 contains eight D-type latches with 3-STATE output buffers. When the Latch Enable (LE) input is HIGH, data on the Dn inputs enters the latches. In this condition the latches are transparent, i.e., a latch output will change state each time its D input changes. When LE is LOW the latches store the information that was present on the D inputs a setup time preceding the HIGH-to-LOW transition of LE. The 3-STATE buffers are controlled by the Output Enable (OE) input. When OE is LOW, the buffers are in the bi-state mode. When OE is HIGH the buffers are in the high impedance mode but this does not interfere with entering new data into the latches. Inputs Internal Output Q O X X Z L H Z High Z H H L Z High Z H L X NC Z Latched L H L H H Transparent L H H L L Transparent L L X NC NC LE D H X H H H OE Function High Z Latched H = HIGH Voltage Level L = LOW Voltage Level X = Immaterial Z = High Impedance NC = No Change Logic Diagram Please note that this diagram is provided only for the understanding of logic operations and should not be used to estimate propagation delays. www.fairchildsemi.com 2 Recommended Operating Conditions Storage Temperature −65°C to +150°C Ambient Temperature under Bias −55°C to +125°C Free Air Ambient Temperature Junction Temperature under Bias −55°C to +150°C Supply Voltage 0°C to +70°C +4.5V to +5.5V −0.5V to +7.0V VCC Pin Potential to Ground Pin Input Voltage (Note 2) −0.5V to +7.0V Input Current (Note 2) −30 mA to +5.0 mA Voltage Applied to Output in HIGH State (with VCC = 0V) Standard Output −0.5V to VCC 3-STATE Output −0.5V to +5.5V Note 1: Absolute maximum ratings are values beyond which the device may be damaged or have its useful life impaired. Functional operation under these conditions is not implied. Note 2: Either voltage limit or current limit is sufficient to protect inputs. Current Applied to Output twice the rated IOL (mA) in LOW State (Max) DC Electrical Characteristics Symbol Parameter Min Typ Max Input HIGH Voltage VIL Input LOW Voltage 0.8 V VCD Input Clamp Diode Voltage −1.2 V VOH Output HIGH 10% VCC 2.5 Voltage 10% VCC 2.4 5% VCC 2.7 5% VCC 2.7 VOL Output LOW Voltage IIH 2.0 Units VIH V 10% VCC Input HIGH Input HIGH Current Output HIGH Leakage Current VID Input Leakage Test IOD Circuit Current Input LOW Current IOZH Output Leakage Current IOZL Output Leakage Current IOS Output Short-Circuit Current IZZ Bus Drainage Test ICCL Power Supply Current ICCZ Power Supply Current IIN = −18 mA Min IOH = −3 mA IOH = −1 mA 0.5 V Min IOL = 24 mA 5.0 µA Max VIN = 2.7V 7.0 µA Max VIN = 7.0V 50 µA Max VOUT = VCC V 0.0 3.75 µA 0.0 −0.6 mA Max VIN = 0.5V 50 µA Max VOUT = 2.7V 4.75 Output Leakage IIL Recognized as a LOW Signal Min IOH = −3 mA Breakdown Test ICEX Conditions Recognized as a HIGH Signal IOH = −1 mA Current IBVI VCC V IID = 1.9 µA All Other Pins Grounded VIOD = 150 mV All Other Pins Grounded −50 µA Max VOUT = 0.5V −150 mA Max VOUT = 0V 500 µA 0.0V VOUT = 5.25V 40 61 mA Max VO = LOW 40 61 mA Max VO = HIGH Z −60 3 www.fairchildsemi.com 74F563 Absolute Maximum Ratings(Note 1) 74F563 AC Electrical Characteristics Symbol Parameter Min TA = +25°C TA = −55°C to +125°C TA = 0°C to +70°C VCC = +5.0V VCC = +5.0V VCC = +5.0V CL = 50 pF CL = 50 pF CL = 50 pF Max Min Max Min tPLH Propagation Delay 3.5 Typ 8.5 3.0 10.5 3.0 9.5 tPHL Dn to On 2.5 6.5 2.0 7.5 2.0 7.0 Max tPLH Propagation Delay 4.5 9.5 4.0 11.0 4.0 10.5 tPHL LE to On 3.0 7.0 2.5 7.5 2.5 7.0 tPZH Output Enable Time 2.0 7.5 2.0 9.5 2.0 9.0 3.0 8.5 2.5 10.0 1.5 9.5 Output Disable Time 1.5 5.5 1.5 7.0 1.5 6.5 1.5 5.5 1.5 5.5 1.5 5.5 tPZL tPHZ tPLZ Units ns ns ns AC Operating Requirements Symbol Parameter TA = +25°C TA = −55°C to +125°C VCC = +5.0V VCC = +5.0V Min Max Min Max TA = 0°C to +70°C VCC = +5.0V Min tS(H) Setup Time, HIGH or LOW 2.0 2.0 2.0 tS(L) Dn to LE 2.0 2.0 2.0 tH(H) Hold Time, HIGH or LOW 3.0 3.0 3.0 tH(L) Dn to LE 3.0 3.0 3.0 tW(H) LE Pulse Width, HIGH 4.0 4.0 4.0 www.fairchildsemi.com 4 Units Max ns ns ns 74F563 Physical Dimensions inches (millimeters) unless otherwise noted 20-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-013, 0.300 Wide Package Number M20B 20-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide Package Number M20D 5 www.fairchildsemi.com 74F563 Octal D-Type Latch with 3-STATE Outputs Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 20-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300 Wide Package Number N20A Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. www.fairchildsemi.com www.fairchildsemi.com 6