TOSHIBA TMP86CH12MG

8 Bit Microcontroller
TLCS-870/C Series
TMP86CH12MG
TMP86CH12MG
The information contained herein is subject to change without notice. 021023 _ D
TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless,
semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and
vulnerability to physical stress.
It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards
of safety in making a safe design for the entire system, and to avoid situations in which a malfunction
or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to
property.
In developing your designs, please ensure that TOSHIBA products are used within specified operating
ranges as set forth in the most recent TOSHIBA products specifications.
Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for
Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. 021023_A
The Toshiba products listed in this document are intended for usage in general electronics applications
(computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic
appliances, etc.).
These Toshiba products are neither intended nor warranted for usage in equipment that requires
extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of
human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control
instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments,
combustion control instruments, medical instruments, all types of safety devices, etc. Unintended
Usage of Toshiba products listed in this document shall be made at the customer's own risk. 021023_B
The products described in this document shall not be used or embedded to any downstream products
of which manufacture, use and/or sale are prohibited under any applicable laws and regulations.
060106_Q
The information contained herein is presented only as a guide for the applications of our products. No
responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third
parties which may result from its use. No license is granted by implication or otherwise under any
patent or patent rights of TOSHIBA or others. 021023_C
The products described in this document may include products subject to the foreign exchange and
foreign trade laws. 021023_F
For a discussion of how the reliability of microcontrollers can be predicted, please refer to Section 1.3
of the chapter entitled Quality and Reliability Assurance/Handling Precautions. 030619_S
© 2006 TOSHIBA CORPORATION
All Rights Reserved
Page 2
Revision History
Date
Revision
2006/6/7
1
First Release
2006/6/29
2
Periodical updating.No change in contents.
2006/10/19
3
Contents Revised
Table of Contents
TMP86CH12MG
1.1
1.2
1.3
1.4
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pin Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pin Names and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
3
4
5
2. Operational Description
2.1
CPU Core Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1.1
2.1.2
2.1.3
Memory Address Map............................................................................................................................... 7
Program Memory (MaskROM).................................................................................................................. 7
Data Memory (RAM) ................................................................................................................................. 8
2.2.1
2.2.2
Clock Generator........................................................................................................................................ 8
Timing Generator .................................................................................................................................... 10
2.2
System Clock Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.2.2.1
2.2.2.2
Configuration of timing generator
Machine cycle
2.2.3.1
2.2.3.2
2.2.3.3
Single-clock mode
Dual-clock mode
STOP mode
2.2.4.1
2.2.4.2
2.2.4.3
2.2.4.4
STOP mode
IDLE1/2 mode and SLEEP1/2 mode
IDLE0 and SLEEP0 modes (IDLE0, SLEEP0)
SLOW mode
2.2.3
2.2.4
2.3
Operation Mode Control Circuit .............................................................................................................. 11
Operating Mode Control ......................................................................................................................... 16
Reset Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
2.3.1
2.3.2
2.3.3
2.3.4
External Reset Input ...............................................................................................................................
Address trap reset ..................................................................................................................................
Watchdog timer reset..............................................................................................................................
System clock reset..................................................................................................................................
29
30
30
30
3. Interrupt Control Circuit
3.1
3.2
Interrupt latches (IL28 to IL2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Interrupt enable register (EIR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
3.2.1
3.2.2
Interrupt master enable flag (IMF) .......................................................................................................... 34
Individual interrupt enable flags (EF28 to EF4) ...................................................................................... 35
3.3.1
3.3.2
Interrupt acceptance processing is packaged as follows........................................................................ 37
Saving/restoring general-purpose registers ............................................................................................ 38
Note 3: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
3.3 Interrupt Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
3.3.2.1
3.3.2.2
Using PUSH and POP instructions
Using data transfer instructions
3.3.3
Interrupt return ........................................................................................................................................ 39
3.4.1
3.4.2
Address error detection .......................................................................................................................... 40
Debugging .............................................................................................................................................. 40
3.4
Software Interrupt (INTSW) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
i
3.5
3.6
3.7
Undefined Instruction Interrupt (INTUNDEF). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Address Trap Interrupt (INTATRAP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
External Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
4. Special Function Register (SFR)
4.1
4.2
SFR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
DBR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
5. I/O Ports
5.1
5.2
5.3
5.4
Port P0 (P07 to P00) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Port P1 (P17 to P10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Port P2 (P22 to P20) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Port P3 (P37 to 30) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
48
51
53
54
6. Watchdog Timer (WDT)
6.1
6.2
Watchdog Timer Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Watchdog Timer Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
6.2.1
6.2.2
6.2.3
6.2.4
6.2.5
Malfunction Detection Methods Using the Watchdog Timer ...................................................................
Watchdog Timer Enable .........................................................................................................................
Watchdog Timer Disable ........................................................................................................................
Watchdog Timer Interrupt (INTWDT)......................................................................................................
Watchdog Timer Reset ...........................................................................................................................
58
59
60
60
61
6.3.1
6.3.2
6.3.3
6.3.4
Selection of Address Trap in Internal RAM (ATAS) ................................................................................
Selection of Operation at Address Trap (ATOUT) ..................................................................................
Address Trap Interrupt (INTATRAP).......................................................................................................
Address Trap Reset ................................................................................................................................
62
62
62
63
6.3
Address Trap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
7. Time Base Timer (TBT)
7.1
Time Base Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
7.1.1
7.1.2
7.1.3
Configuration .......................................................................................................................................... 65
Control .................................................................................................................................................... 65
Function .................................................................................................................................................. 66
7.2.1
7.2.2
Configuration .......................................................................................................................................... 67
Control .................................................................................................................................................... 67
7.2
Divider Output (DVO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
8. Real-Time Clock
8.1
8.2
8.3
ii
Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Control of the RTC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
9. 10-Bit Timer/Counter (TC7)
9.1
9.2
9.3
9.4
Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuring Control and Data Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.4.1
71
71
75
76
Programmable pulse generator output (PPG output) ............................................................................. 76
9.4.1.1
9.4.1.2
9.4.1.3
50% duty mode
Variable duty mode
PPG1/PPG2 independent mode
9.4.2.1
9.4.2.2
9.4.2.3
9.4.2.4
9.4.2.5
Command start and capture mode
Command start and trigger start mode
Trigger start mode
Trigger capture mode (CSTC = 00)
Trigger start/stop acceptance mode
9.4.3.1
9.4.3.2
9.4.3.3
Counting stopped with the outputs initialized
Counting stopped with the outputs maintained
Counting stopped with the outputs initialized at the end of the period
9.4.4.1
9.4.4.2
One-time output mode
Continuous output mode
9.4.5.1
9.4.5.2
9.4.5.3
Specifying initial values and output logic for PPG outputs
Enabling or disabling PPG outputs
Using the TC7 as a normal timer/counter
9.4.7.1
9.4.7.2
9.4.7.3
INTTC7T (Trigger start interrupt)
INTTC7P (Period interrupt)
INTEMG (Emergency output stop interrupt)
9.4.8.1
9.4.8.2
9.4.8.3
9.4.8.4
9.4.8.5
9.4.8.6
Enabling/disabling input on the EMG pin
Monitoring the emergency PPG output stop state
EMG interrupt
Canceling the emergency PPG output stop state
Restarting the timer after canceling the emergency PPG output stop state
Response time between EMG pin input and PPG outputs being initialized
9.4.2
Starting a count....................................................................................................................................... 80
9.4.3
Configuring how the timer stops ............................................................................................................. 87
9.4.4
One-time/continuous output mode.......................................................................................................... 87
9.4.5
PPG output control (Initial value/output logic, enabling/disabling output) ............................................... 89
9.4.6
9.4.7
Eliminating noise from the TC7 pin input ................................................................................................ 89
Interrupts................................................................................................................................................. 91
9.4.8
Emergency PPG output stop feature ...................................................................................................... 92
9.4.9
TC7 operation and microcontroller operating mode ............................................................................... 94
10. 16-Bit TimerCounter 1 (TC1)
10.1
10.2
10.3
Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
TimerCounter Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
10.3.1
10.3.2
10.3.3
10.3.4
10.3.5
10.3.6
Timer mode........................................................................................................................................... 98
External Trigger Timer Mode .............................................................................................................. 100
Event Counter Mode ........................................................................................................................... 102
Window Mode ..................................................................................................................................... 103
Pulse Width Measurement Mode........................................................................................................ 104
Programmable Pulse Generate (PPG) Output Mode ......................................................................... 107
11. 8-Bit TimerCounter (TC3, TC4)
11.1
11.2
11.3
Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
TimerCounter Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
11.3.1
11.3.2
11.3.3
11.3.4
8-Bit Timer Mode (TC3 and 4) ............................................................................................................
8-Bit Event Counter Mode (TC3, 4) ....................................................................................................
8-Bit Programmable Divider Output (PDO) Mode (TC3, 4).................................................................
8-Bit Pulse Width Modulation (PWM) Output Mode (TC3, 4)..............................................................
117
118
118
121
iii
11.3.5
11.3.6
11.3.7
11.3.8
11.3.9
16-Bit Timer Mode (TC3 and 4) ..........................................................................................................
16-Bit Event Counter Mode (TC3 and 4) ............................................................................................
16-Bit Pulse Width Modulation (PWM) Output Mode (TC3 and 4)......................................................
16-Bit Programmable Pulse Generate (PPG) Output Mode (TC3 and 4) ...........................................
Warm-Up Counter Mode.....................................................................................................................
11.3.9.1
11.3.9.2
123
124
124
127
129
Low-Frequency Warm-up Counter Mode
(NORMAL1 → NORMAL2 → SLOW2 → SLOW1)
High-Frequency Warm-Up Counter Mode
(SLOW1 → SLOW2 → NORMAL2 → NORMAL1)
12. Synchronous Serial Interface (SIO)
12.1
12.2
12.3
Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Serial clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
12.3.1
Internal clock
External clock
12.3.2.1
12.3.2.2
Leading edge
Trailing edge
12.3.2
12.4
12.5
12.6
Clock source ....................................................................................................................................... 133
12.3.1.1
12.3.1.2
Shift edge............................................................................................................................................ 135
Number of bits to transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Number of words to transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Transfer Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
12.6.1
12.6.2
12.6.3
4-bit and 8-bit transfer modes ............................................................................................................. 136
4-bit and 8-bit receive modes ............................................................................................................. 138
8-bit transfer / receive mode ............................................................................................................... 139
13. Asynchronous Serial interface (UART )
13.1
13.2
13.3
13.4
13.5
13.6
13.7
13.8
Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transfer Data Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transfer Rate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Data Sampling Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
STOP Bit Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transmit/Receive Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.8.1
13.8.2
Data Transmit Operation .................................................................................................................... 146
Data Receive Operation ..................................................................................................................... 146
13.9.1
13.9.2
13.9.3
13.9.4
13.9.5
13.9.6
Parity Error..........................................................................................................................................
Framing Error......................................................................................................................................
Overrun Error ......................................................................................................................................
Receive Data Buffer Full.....................................................................................................................
Transmit Data Buffer Empty ...............................................................................................................
Transmit End Flag ..............................................................................................................................
13.9
141
142
144
145
145
146
146
146
Status Flag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
147
147
147
148
148
149
14. 10-bit AD Converter (ADC)
14.1
14.2
14.3
Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
Register configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
14.3.1
14.3.2
iv
Software Start Mode ........................................................................................................................... 155
Repeat Mode ...................................................................................................................................... 155
14.3.3
Register Setting ................................................................................................................................ 156
14.6.1
14.6.2
14.6.3
Analog input pin voltage range ........................................................................................................... 159
Analog input shared pins .................................................................................................................... 159
Noise Countermeasure ....................................................................................................................... 159
14.4
14.5
14.6
STOP/SLOW Modes during AD Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
Analog Input Voltage and AD Conversion Result . . . . . . . . . . . . . . . . . . . . . . . 158
Precautions about AD Converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
15. Key-on Wakeup (KWU)
15.1
15.2
15.3
Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
16. Input/Output Circuit
16.1
16.2
Control pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Input/Output Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
17. Electrical Characteristics
17.1
17.2
17.2
17.2
17.3
17.4
17.5
17.6
17.7
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
Recommended Operating Condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
............................................................................................................................................................... 165
............................................................................................................................................................... 165
DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AD Conversion Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recommended Oscillating Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Handling Precaution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
166
167
167
168
168
18. Package Dimension
This is a technical document that describes the operating functions and electrical
specifications of the 8-bit microcontroller series TLCS-870/C (LSI).
v
vi
TMP86CH12MG
CMOS 8-Bit Microcontroller
TMP86CH12MG
Product No.
ROM
(MaskROM)
RAM
Package
FLASH MCU
Emulation Chip
TMP86CH12MG
16384
bytes
512
bytes
P-SSOP30-56-0.65
TMP86FH12MG
TMP86C912XB
1.1 Features
1. 8-bit single chip microcomputer TLCS-870/C series
- Instruction execution time :
0.25 µs (at 16 MHz)
122 µs (at 32.768 kHz)
- 132 types & 731 basic instructions
2. 22interrupt sources (External : 6 Internal : 16)
3. Input / Output ports (24 pins)
Large current output: 8pins (Typ. 20mA), LED direct drive
4. Watchdog Timer
5. Prescaler
- Time base timer
- Divider output function
6. 10-bit timer counter: 1ch (2 output pins)
2ports output PPG (Programmed Pulse Generator)
50%duty output mode
Variable Duty output mode
External-triggered start and stop
Emargency stop pin
7. 16-bit timer counter: 1 ch
- Timer, External trigger, Window, Pulse width measurement,
060116EBP
• The information contained herein is subject to change without notice. 021023_D
• TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can
malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when
utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations
in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property.
In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most
recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for
Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. 021023_A
• The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are neither
intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunctionor failure of
which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments,
airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc. Unintended Usage of TOSHIBA products listed in this document shall be made at the customer's
own risk. 021023_B
• The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or
sale are prohibited under any applicable laws and regulations. 060106_Q
• The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by
TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of TOSHIBA or others. 021023_C
• The products described in this document are subject to the foreign exchange and foreign trade laws. 021023_E
• For a discussion of how the reliability of microcontrollers can be predicted, please refer to Section 1.3 of the chapter entitled Quality and
Reliability Assurance/Handling Precautions. 030619_S
Page 1
1.1 Features
TMP86CH12MG
Event counter, Programmable pulse generate (PPG) modes
8. 8-bit timer counter : 2 ch
- Timer, Event counter, Programmable divider output (PDO),
Pulse width modulation (PWM) output,
Programmable pulse generation (PPG) modes
9. 8-bit SIO: 1 ch
10. 8-bit UART : 1 ch
11. 10-bit successive approximation type AD converter
- Analog input: 8 ch
12. Key-on wakeup : 4 ch
13. Clock operation
Single clock mode
Dual clock mode
14. Low power consumption operation
STOP mode: Oscillation stops. (Battery/Capacitor back-up.)
SLOW1 mode: Low power consumption operation using low-frequency clock.(High-frequency clock
stop.)
SLOW2 mode: Low power consumption operation using low-frequency clock.(High-frequency clock
oscillate.)
IDLE0 mode: CPU stops, and only the Time-Based-Timer(TBT) on peripherals operate using high frequency clock. Release by falling edge of the source clock which is set by TBTCR<TBTCK>.
IDLE1 mode: CPU stops and peripherals operate using high frequency clock. Release by interruputs(CPU restarts).
IDLE2 mode: CPU stops and peripherals operate using high and low frequency clock. Release by interruputs. (CPU restarts).
SLEEP0 mode: CPU stops, and only the Time-Based-Timer(TBT) on peripherals operate using low frequency clock.Release by falling edge of the source clock which is set by TBTCR<TBTCK>.
SLEEP1 mode: CPU stops, and peripherals operate using low frequency clock. Release by interruput.(CPU restarts).
SLEEP2 mode: CPU stops and peripherals operate using high and low frequency clock.
interruput.
15. Wide operation voltage:
2.7 V to 5.5 V at 8MHz /32.768 kHz
4.5 V to 5.5 V at 16 MHz /32.768 kHz
Page 2
Release by
TMP86CH12MG
1.2 Pin Assignment
VSS
XIN
XOUT
TEST
VDD
(XTIN) P21
(XTOUT) P22
RESET
(INT5/STOP) P20
(TC1/INT4) P14
(TXD) P00
(RXD) P01
(SCK) P02
(SI) P03
(SO) P04
30 P37 (AIN7)
29 P36 (AIN6/STOP3)
28 P35 (AIN5/STOP2)
27 P34 (AIN4/STOP1)
26 P33 (AIN3/STOP0)
25 P32 (AIN2)
24 P31 (AIN1/INT0)
23 P30 (AIN0/EMG)
22 P13 (PPG/INT3)
21 P12 (DVO)
20 P11 (TC4/PDO4/PWM4/PPG4)
19 P10 (TC3/PDO3/PWM3)
18 P07 (PPG2/INT2)
17 P06 (PPG1/INT1)
16 P05 (TC7)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Figure 1-1 Pin Assignment
Page 3
1.3 Block Diagram
TMP86CH12MG
1.3 Block Diagram
Figure 1-2 Block Diagram
Page 4
TMP86CH12MG
1.4 Pin Names and Functions
Table 1-1 Pin Names and Functions(1/2)
Pin Name
Pin Number
Input/Output
Functions
P07
PPG2
INT2
18
IO
O
I
PORT07
Timer counter 7 PPG2 output
External interrupt 2 input
P06
PPG1
INT1
17
IO
O
I
PORT06
Timer counter 7 PPG1 output
External interrupt 1 input
P05
TC7
16
IO
I
PORT05
Timer counter 7 input
P04
SO
15
IO
O
PORT04
Serial Data Output
P03
SI
14
IO
I
PORT03
Serial Data Input
13
IO
IO
PORT02
Serial Clock I/O
P01
RXD
12
IO
I
PORT01
UART data input
P00
TXD
11
IO
O
PORT00
UART data output
P14
INT4
TC1
10
IO
I
I
PORT14
External interrupt 4 input
TC1 input
22
IO
O
I
PORT13
PPG output
External interrupt 3 input
21
IO
O
PORT12
Divider Output
20
IO
I
O
PORT11
TC4 input
PDO4/PWM4/PPG4 output
19
IO
I
O
PORT10
TC3 input
PDO3/PWM3 output
P22
XTOUT
7
IO
O
PORT22
Resonator connecting pins(32.768kHz) for inputting external
clock
P21
XTIN
6
IO
I
PORT21
Resonator connecting pins(32.768kHz) for inputting external
clock
9
IO
I
I
PORT20
STOP mode release signal input
External interrupt 5 input
P37
AIN7
30
IO
I
PORT37
Analog Input7
P36
AIN6
STOP3
29
IO
I
I
PORT36
Analog Input6
STOP3 input
P02
SCK
P13
PPG
INT3
P12
DVO
P11
TC4
PDO4/PWM4/PPG4
P10
TC3
PDO3/PWM3
P20
STOP
INT5
Page 5
1.4 Pin Names and Functions
TMP86CH12MG
Table 1-1 Pin Names and Functions(2/2)
Pin Name
Pin Number
Input/Output
Functions
P35
AIN5
STOP2
28
IO
I
I
PORT35
Analog Input5
STOP2 input
P34
AIN4
STOP1
27
IO
I
I
PORT34
Analog Input4
STOP1 input
P33
AIN3
STOP0
26
IO
I
I
PORT33
Analog Input3
STOP0 input
P32
AIN2
25
IO
I
PORT32
Analog Input2
24
IO
I
I
PORT31
Analog Input1
External interrupt 0 input
23
IO
I
I
PORT30
Analog Input0
Timer counter 7 Emergency stop input
XIN
2
I
Resonator connecting pins for high-frequency clock
XOUT
3
O
Resonator connecting pins for high-frequency clock
RESET
8
I
Reset signal
TEST
4
I
Test pin for out-going test. Normally, be fixed to low.
VDD
5
I
+5V
VSS
1
I
0(GND)
P31
AIN1
INT0
P30
AIN0
EMG
Page 6
TMP86CH12MG
2. Operational Description
2.1 CPU Core Functions
The CPU core consists of a CPU, a system clock controller, and an interrupt controller.
This section provides a description of the CPU core, the program memory, the data memory, and the reset circuit.
2.1.1
Memory Address Map
The TMP86CH12MG memory is composed MaskROM, RAM, DBR(Data buffer register) and SFR(Special
function register). They are all mapped in 64-Kbyte address space. Figure 2-1 shows the
memory address map.
0000H
SFR
SFR:
64 bytes
003FH
0040H
512
bytes
RAM
RAM:
Special function register includes:
I/O ports
Peripheral control registers
Peripheral status registers
System control registers
Program status word
Random access memory includes:
Data memory
Stack
023FH
0F80H
DBR:
128
bytes
DBR
TMP86CH12MG
Data buffer register includes:
Peripheral control registers
Peripheral status registers
0FFFH
C000H
MaskROM:
Program memory
16384
bytes
MaskROM
FFA0H
Vector table for interrupts
(32 bytes)
FFBFH
FFC0H
Vector table for vector call instructions
(32 bytes)
FFDFH
FFE0H
Vector table for interrupts
FFFFH
(32 bytes)
Figure 2-1 Memory Address Map
2.1.2
Program Memory (MaskROM)
The TMP86CH12MG has a 16384 bytes (Address C000H to FFFFH) of program memory (MaskROM ).
Page 7
2. Operational Description
2.2 System Clock Controller
2.1.3
TMP86CH12MG
Data Memory (RAM)
The TMP86CH12MG has 512bytes (Address 0040H to 023FH) of internal RAM. The first 192 bytes
(0040H to 00FFH) of the internal RAM are located in the direct area; instructions with shorten operations are
available against such an area.
The data memory contents become unstable when the power supply is turned on; therefore, the data memory
should be initialized by an initialization routine.
Example :Clears RAM to “00H”. (TMP86CH12MG)
SRAMCLR:
LD
HL, 0040H
; Start address setup
LD
A, H
; Initial value (00H) setup
LD
BC, 01FFH
LD
(HL), A
INC
HL
DEC
BC
JRS
F, SRAMCLR
2.2 System Clock Controller
The system clock controller consists of a clock generator, a timing generator, and a standby controller.
Timing generator control register
TBTCR
0036H
Clock
generator
XIN
fc
High-frequency
clock oscillator
Timing
generator
XOUT
Standby controller
0038H
XTIN
Low-frequency
clock oscillator
SYSCR1
fs
System clocks
0039H
SYSCR2
System control registers
XTOUT
Clock generator control
Figure 2-2 System Colck Control
2.2.1
Clock Generator
The clock generator generates the basic clock which provides the system clocks supplied to the CPU core
and peripheral hardware. It contains two oscillation circuits: One for the high-frequency clock and one for the
low-frequency clock. Power consumption can be reduced by switching of the standby controller to low-power
operation based on the low-frequency clock.
The high-frequency (fc) clock and low-frequency (fs) clock can easily be obtained by connecting a resonator
between the XIN/XOUT and XTIN/XTOUT pins respectively. Clock input from an external oscillator is also
possible. In this case, external clock is applied to XIN/XTIN pin with XOUT/XTOUT pin not connected.
Page 8
TMP86CH12MG
Low-frequency clock
High-frequency clock
XIN
XOUT
XIN
XOUT
XTIN
XTOUT
(Open)
(a) Crystal/Ceramic
resonator
XTIN
XTOUT
(Open)
(c) Crystal
(b) External oscillator
(d) External oscillator
Figure 2-3 Examples of Resonator Connection
Note:The function to monitor the basic clock directly at external is not provided for hardware, however, with disabling all interrupts and watchdog timers, the oscillation frequency can be adjusted by monitoring the pulse
which the fixed frequency is outputted to the port by the program.
The system to require the adjustment of the oscillation frequency should create the program for the adjustment in advance.
Page 9
2. Operational Description
2.2 System Clock Controller
2.2.2
TMP86CH12MG
Timing Generator
The timing generator generates the various system clocks supplied to the CPU core and peripheral hardware
from the basic clock (fc or fs). The timing generator provides the following functions.
1. Generation of main system clock
2. Generation of divider output (DVO) pulses
3. Generation of source clocks for time base timer
4. Generation of source clocks for watchdog timer
5. Generation of internal source clocks for timer/counters
6. Generation of warm-up clocks for releasing STOP mode
2.2.2.1
Configuration of timing generator
The timing generator consists of a 2-stage prescaler, a 21-stage divider, a main system clock generator,
and machine cycle counters.
An input clock to the 7th stage of the divider depends on the operating mode, SYSCR2<SYSCK> and
TBTCR<DV7CK>, that is shown in Figure 2-4. As reset and STOP mode started/canceled, the prescaler
and the divider are cleared to “0”.
fc or fs
Main system clock generator
Machine cycle counters
SYSCK
DV7CK
High-frequency
clock fc
Low-frequency
clock fs
1 2
fc/4
S
A
1 2 3 4 5 6
Divider
Y
B
7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
Multiplexer
S
B0
B1
A0 Y0
A1 Y1
Multiplexer
Warm-up
controller
Watchdog
timer
Timer counter, Serial interface, Time-base-timer, divider output, etc. (Peripheral functions)
Figure 2-4 Configuration of Timing Generator
Page 10
TMP86CH12MG
Timing Generator Control Register
TBTCR
(0036H)
7
6
(DVOEN)
5
(DVOCK)
DV7CK
4
3
DV7CK
(TBTEN)
Selection of input to the 7th stage
of the divider
2
1
0
(TBTCK)
(Initial value: 0000 0000)
0: fc/28 [Hz]
1: fs
R/W
Note 1: In single clock mode, do not set DV7CK to “1”.
Note 2: Do not set “1” on DV7CK while the low-frequency clock is not operated stably.
Note 3: fc: High-frequency clock [Hz], fs: Low-frequency clock [Hz], *: Don’t care
Note 4: In SLOW1/2 and SLEEP1/2 modes, the DV7CK setting is ineffective, and fs is input to the 7th stage of the divider.
Note 5: When STOP mode is entered from NORMAL1/2 mode, the DV7CK setting is ineffective during the warm-up period after
release of STOP mode, and the 6th stage of the divider is input to the 7th stage during this period.
2.2.2.2
Machine cycle
Instruction execution and peripheral hardware operation are synchronized with the main system clock.
The minimum instruction execution unit is called an “machine cycle”. There are a total of 10 different
types of instructions for the TLCS-870/C Series: Ranging from 1-cycle instructions which require one
machine cycle for execution to 10-cycle instructions which require 10 machine cycles for execution. A
machine cycle consists of 4 states (S0 to S3), and each state consists of one main system clock.
1/fc or 1/fs [s]
Main system clock
State
S0
S1
S2
S3
S0
S1
S2
S3
Machine cycle
Figure 2-5 Machine Cycle
2.2.3
Operation Mode Control Circuit
The operation mode control circuit starts and stops the oscillation circuits for the high-frequency and lowfrequency clocks, and switches the main system clock. There are three operating modes: Single clock mode,
dual clock mode and STOP mode. These modes are controlled by the system control registers (SYSCR1 and
SYSCR2). Figure 2-6 shows the operating mode transition diagram.
2.2.3.1
Single-clock mode
Only the oscillation circuit for the high-frequency clock is used, and P21 (XTIN) and P22 (XTOUT)
pins are used as input/output ports. The main-system clock is obtained from the high-frequency clock. In
the single-clock mode, the machine cycle time is 4/fc [s].
(1)
NORMAL1 mode
In this mode, both the CPU core and on-chip peripherals operate using the high-frequency clock.
The TMP86CH12MG is placed in this mode after reset.
Page 11
2. Operational Description
2.2 System Clock Controller
TMP86CH12MG
(2)
IDLE1 mode
In this mode, the internal oscillation circuit remains active. The CPU and the watchdog timer are
halted; however on-chip peripherals remain active (Operate using the high-frequency clock).
IDLE1 mode is started by SYSCR2<IDLE> = "1", and IDLE1 mode is released to NORMAL1
mode by an interrupt request from the on-chip peripherals or external interrupt inputs. When the IMF
(Interrupt master enable flag) is “1” (Interrupt enable), the execution will resume with the acceptance
of the interrupt, and the operation will return to normal after the interrupt service is completed. When
the IMF is “0” (Interrupt disable), the execution will resume with the instruction which follows the
IDLE1 mode start instruction.
(3)
IDLE0 mode
In this mode, all the circuit, except oscillator and the timer-base-timer, stops operation.
This mode is enabled by SYSCR2<TGHALT> = "1".
When IDLE0 mode starts, the CPU stops and the timing generator stops feeding the clock to the
peripheral circuits other than TBT. Then, upon detecting the falling edge of the source clock selected
with TBTCR<TBTCK>, the timing generator starts feeding the clock to all peripheral circuits.
When returned from IDLE0 mode, the CPU restarts operating, entering NORMAL1 mode back
again. IDLE0 mode is entered and returned regardless of how TBTCR<TBTEN> is set. When IMF =
“1”, EF1 (TBT interrupt individual enable flag) = “1”, and TBTCR<TBTEN> = “1”, interrupt processing is performed. When IDLE0 mode is entered while TBTCR<TBTEN> = “1”, the INTTBT
interrupt latch is set after returning to NORMAL1 mode.
2.2.3.2
Dual-clock mode
Both the high-frequency and low-frequency oscillation circuits are used in this mode. P21 (XTIN) and
P22 (XTOUT) pins cannot be used as input/output ports. The main system clock is obtained from the
high-frequency clock in NORMAL2 and IDLE2 modes, and is obtained from the low-frequency clock in
SLOW and SLEEP modes. The machine cycle time is 4/fc [s] in the NORMAL2 and IDLE2 modes, and
4/fs [s] (122 µs at fs = 32.768 kHz) in the SLOW and SLEEP modes.
The TLCS-870/C is placed in the signal-clock mode during reset. To use the dual-clock mode, the lowfrequency oscillator should be turned on at the start of a program.
(1)
NORMAL2 mode
In this mode, the CPU core operates with the high-frequency clock. On-chip peripherals operate
using the high-frequency clock and/or low-frequency clock.
(2)
SLOW2 mode
In this mode, the CPU core operates with the low-frequency clock, while both the high-frequency
clock and the low-frequency clock are operated. As the SYSCR2<SYSCK> becomes "1", the hardware changes into SLOW2 mode. As the SYSCR2<SYSCK> becomes “0”, the hardware changes
into NORMAL2 mode. As the SYSCR2<XEN> becomes “0”, the hardware changes into SLOW1
mode. Do not clear SYSCR2<XTEN> to “0” during SLOW2 mode.
(3)
SLOW1 mode
This mode can be used to reduce power-consumption by turning off oscillation of the high-frequency clock. The CPU core and on-chip peripherals operate using the low-frequency clock.
Page 12
TMP86CH12MG
Switching back and forth between SLOW1 and SLOW2 modes are performed by
SYSCR2<XEN>. In SLOW1 and SLEEP modes, the input clock to the 1st stage of the divider is
stopped; output from the 1st to 6th stages is also stopped.
(4)
IDLE2 mode
In this mode, the internal oscillation circuit remain active. The CPU and the watchdog timer are
halted; however, on-chip peripherals remain active (Operate using the high-frequency clock and/or
the low-frequency clock). Starting and releasing of IDLE2 mode are the same as for IDLE1 mode,
except that operation returns to NORMAL2 mode.
(5)
SLEEP1 mode
In this mode, the internal oscillation circuit of the low-frequency clock remains active. The CPU,
the watchdog timer, and the internal oscillation circuit of the high-frequency clock are halted; however, on-chip peripherals remain active (Operate using the low-frequency clock). Starting and releasing of SLEEP mode are the same as for IDLE1 mode, except that operation returns to SLOW1 mode.
In SLOW1 and SLEEP1 modes, the input clock to the 1st stage of the divider is stopped; output from
the 1st to 6th stages is also stopped.
(6)
SLEEP2 mode
The SLEEP2 mode is the idle mode corresponding to the SLOW2 mode. The status under the
SLEEP2 mode is same as that under the SLEEP1 mode, except for the oscillation circuit of the highfrequency clock.
(7)
SLEEP0 mode
In this mode, all the circuit, except oscillator and the timer-base-timer, stops operation. This mode
is enabled by setting “1” on bit SYSCR2<TGHALT>.
When SLEEP0 mode starts, the CPU stops and the timing generator stops feeding the clock to the
peripheral circuits other than TBT. Then, upon detecting the falling edge of the source clock selected
with TBTCR<TBTCK>, the timing generator starts feeding the clock to all peripheral circuits.
When returned from SLEEP0 mode, the CPU restarts operating, entering SLOW1 mode back
again. SLEEP0 mode is entered and returned regardless of how TBTCR<TBTEN> is set. When IMF
= “1”, EF1 (TBT interrupt individual enable flag) = “1”, and TBTCR<TBTEN> = “1”, interrupt processing is performed. When SLEEP0 mode is entered while TBTCR<TBTEN> = “1”, the INTTBT
interrupt latch is set after returning to SLOW1 mode.
2.2.3.3
STOP mode
In this mode, the internal oscillation circuit is turned off, causing all system operations to be halted. The
internal status immediately prior to the halt is held with a lowest power consumption during STOP mode.
STOP mode is started by the system control register 1 (SYSCR1), and STOP mode is released by a
inputting (Either level-sensitive or edge-sensitive can be programmably selected) to the STOP pin. After
the warm-up period is completed, the execution resumes with the instruction which follows the STOP
mode start instruction.
Page 13
2. Operational Description
2.2 System Clock Controller
TMP86CH12MG
IDLE0
mode
RESET
Reset release
Note 2
SYSCR2<TGHALT> = "1"
SYSCR1<STOP> = "1"
SYSCR2<IDLE> = "1"
NORMAL1
mode
Interrupt
STOP pin input
IDLE1
mode
(a) Single-clock mode
SYSCR2<XTEN> = "0"
SYSCR2<XTEN> = "1"
SYSCR2<IDLE> = "1"
IDLE2
mode
NORMAL2
mode
Interrupt
SYSCR1<STOP> = "1"
STOP pin input
SYSCR2<SYSCK> = "0"
SYSCR2<SYSCK> = "1"
STOP
SYSCR2<IDLE> = "1"
SLEEP2
mode
SLOW2
mode
Interrupt
SYSCR2<XEN> = "0"
SYSCR2<XEN> = "1"
SYSCR2<IDLE> = "1"
SLEEP1
mode
Interrupt
(b) Dual-clock mode
SYSCR1<STOP> = "1"
SLOW1
mode
STOP pin input
SYSCR2<TGHALT> = "1"
Note 2
SLEEP0
mode
Note 1: NORMAL1 and NORMAL2 modes are generically called NORMAL; SLOW1 and SLOW2 are called SLOW; IDLE0, IDLE1
and IDLE2 are called IDLE; SLEEP0, SLEEP1 and SLEEP2 are called SLEEP.
Note 2: The mode is released by falling edge of TBTCR<TBTCK> setting.
Figure 2-6 Operating Mode Transition Diagram
Table 2-1 Operating Mode and Conditions
Oscillator
Operating Mode
High
Frequency
Low
Frequency
RESET
NORMAL1
Single clock
IDLE1
Oscillation
Reset
Operate
Halt
Operate
Halt
Operate with
high frequency
Machine Cycle
Time
4/fc [s]
–
4/fc [s]
Halt
Oscillation
Operate with
low frequency
Oscillation
Halt
Operate
Operate
Operate with
low frequency
SLOW1
4/fs [s]
Stop
SLEEP0
STOP
Reset
Stop
SLEEP2
SLEEP1
Reset
Halt
SLOW2
Dual clock
Other
Peripherals
Stop
NORMAL2
IDLE2
TBT
Operate
IDLE0
STOP
CPU Core
Halt
Stop
Halt
Page 14
Halt
–
TMP86CH12MG
System Control Register 1
SYSCR1
7
6
5
4
(0038H)
STOP
RELM
RETM
OUTEN
3
2
1
0
WUT
(Initial value: 0000 00**)
STOP
STOP mode start
0: CPU core and peripherals remain active
1: CPU core and peripherals are halted (Start STOP mode)
R/W
RELM
Release method for STOP
mode
0: Edge-sensitive release
1: Level-sensitive release
R/W
RETM
Operating mode after STOP
mode
0: Return to NORMAL1/2 mode
1: Return to SLOW1 mode
R/W
Port output during STOP mode
0: High impedance
1: Output kept
R/W
OUTEN
WUT
Warm-up time at releasing
STOP mode
Return to NORMAL mode
Return to SLOW mode
00
3 x 216/fc
3 x 213/fs
01
216/fc
213/fs
10
3 x 214/fc
3 x 26/fs
11
214/fc
26/fs
R/W
Note 1: Always set RETM to “0” when transiting from NORMAL mode to STOP mode. Always set RETM to “1” when transiting
from SLOW mode to STOP mode.
Note 2: When STOP mode is released with RESET pin input, a return is made to NORMAL1 regardless of the RETM contents.
Note 3: fc: High-frequency clock [Hz], fs: Low-frequency clock [Hz], *; Don’t care
Note 4: Bits 1 and 0 in SYSCR1 are read as undefined data when a read instruction is executed.
Note 5: As the hardware becomes STOP mode under OUTEN = “0”, input value is fixed to “0”; therefore it may cause external
interrupt request on account of falling edge.
Note 6: When the key-on wakeup is used, RELM should be set to "1".
Note 7: Port P20 is used as STOP pin. Therefore, when stop mode is started, OUTEN does not affect to P20, and P20 becomes
High-Z mode.
Note 8: The warmig-up time should be set correctly for using oscillator.
System Control Register 2
SYSCR2
(0039H)
7
6
5
4
XEN
XTEN
SYSCK
IDLE
3
2
1
TGHALT
0
(Initial value: 1000 *0**)
XEN
High-frequency oscillator control
0: Turn off oscillation
1: Turn on oscillation
XTEN
Low-frequency oscillator control
0: Turn off oscillation
1: Turn on oscillation
SYSCK
Main system clock select
(Write)/main system clock monitor (Read)
0: High-frequency clock (NORMAL1/NORMAL2/IDLE1/IDLE2)
1: Low-frequency clock (SLOW1/SLOW2/SLEEP1/SLEEP2)
IDLE
CPU and watchdog timer control
(IDLE1/2 and SLEEP1/2 modes)
0: CPU and watchdog timer remain active
1: CPU and watchdog timer are stopped (Start IDLE1/2 and SLEEP1/2 modes)
TGHALT
TG control (IDLE0 and SLEEP0
modes)
0: Feeding clock to all peripherals from TG
1: Stop feeding clock to peripherals except TBT from TG.
(Start IDLE0 and SLEEP0 modes)
R/W
R/W
Note 1: A reset is applied if both XEN and XTEN are cleared to “0”, XEN is cleared to “0” when SYSCK = “0”, or XTEN is cleared
to “0” when SYSCK = “1”.
Note 2: *: Don’t care, TG: Timing generator, *; Don’t care
Note 3: Bits 3, 1 and 0 in SYSCR2 are always read as undefined value.
Note 4: Do not set IDLE and TGHALT to “1” simultaneously.
Note 5: Because returning from IDLE0/SLEEP0 to NORMAL1/SLOW1 is executed by the asynchronous internal clock, the period
of IDLE0/SLEEP0 mode might be shorter than the period setting by TBTCR<TBTCK>.
Note 6: When IDLE1/2 or SLEEP1/2 mode is released, IDLE is automatically cleared to “0”.
Note 7: When IDLE0 or SLEEP0 mode is released, TGHALT is automatically cleared to “0”.
Note 8: Before setting TGHALT to “1”, be sure to stop peripherals. If peripherals are not stopped, the interrupt latch of peripherals
may be set after IDLE0 or SLEEP0 mode is released.
Page 15
2. Operational Description
2.2 System Clock Controller
2.2.4
TMP86CH12MG
Operating Mode Control
2.2.4.1
STOP mode
STOP mode is controlled by the system control register 1, the STOP pin input and key-on wakeup input
(STOP3 to STOP0) which is controlled by the STOP mode release control register (STOPCR).
The STOP pin is also used both as a port P20 and an INT5 (external interrupt input 5) pin. STOP mode is
started by setting SYSCR1<STOP> to “1”. During STOP mode, the following status is maintained.
1. Oscillations are turned off, and all internal operations are halted.
2. The data memory, registers, the program status word and port output latches are all held in the
status in effect before STOP mode was entered.
3. The prescaler and the divider of the timing generator are cleared to “0”.
4. The program counter holds the address 2 ahead of the instruction (e.g., [SET (SYSCR1).7])
which started STOP mode.
STOP mode includes a level-sensitive mode and an edge-sensitive mode, either of which can be
selected with the SYSCR1<RELM>. Do not use any key-on wakeup input (STOP3 to STOP0) for releasing STOP mode in edge-sensitive mode.
Note 1: The STOP mode can be released by either the STOP or key-on wakeup pin (STOP3 to STOP0).
However, because the STOP pin is different from the key-on wakeup and can not inhibit the release
input, the STOP pin must be used for releasing STOP mode.
Note 2: During STOP period (from start of STOP mode to end of warm up), due to changes in the external
interrupt pin signal, interrupt latches may be set to “1” and interrupts may be accepted immediately
after STOP mode is released. Before starting STOP mode, therefore, disable interrupts. Also, before
enabling interrupts after STOP mode is released, clear unnecessary interrupt latches.
(1)
Level-sensitive release mode (RELM = “1”)
In this mode, STOP mode is released by setting the STOP pin high or setting the STOP3 to STOP0
pin input which is enabled by STOPCR. This mode is used for capacitor backup when the main
power supply is cut off and long term battery backup.
Even if an instruction for starting STOP mode is executed while STOP pin input is high or STOP3
to STOP0 input is low, STOP mode does not start but instead the warm-up sequence starts immediately. Thus, to start STOP mode in the level-sensitive release mode, it is necessary for the program to
first confirm that the STOP pin input is low or STOP3 to STOP0 input is high. The following two
methods can be used for confirmation.
1. Testing a port.
2. Using an external interrupt input INT5 (INT5 is a falling edge-sensitive input).
Example 1 :Starting STOP mode from NORMAL mode by testing a port P20.
SSTOPH:
LD
(SYSCR1), 01010000B
; Sets up the level-sensitive release mode
TEST
(P2PRD). 0
; Wait until the STOP pin input goes low level
JRS
F, SSTOPH
; IMF ← 0
DI
SET
(SYSCR1). 7
; Starts STOP mode
Page 16
TMP86CH12MG
Example 2 :Starting STOP mode from NORMAL mode with an INT5 interrupt.
PINT5:
TEST
(P2PRD). 0
; To reject noise, STOP mode does not start if
JRS
F, SINT5
LD
(SYSCR1), 01010000B
port P20 is at high
; Sets up the level-sensitive release mode.
; IMF ← 0
DI
SET
SINT5:
(SYSCR1). 7
; Starts STOP mode
RETI
VIH
STOP pin
XOUT pin
NORMAL
operation
STOP
operation
Warm up
Confirm by program that the
STOP pin input is low and start
STOP mode.
NORMAL
operation
STOP mode is released by the hardware.
Always released if the STOP
pin input is high.
Figure 2-7 Level-sensitive Release Mode
Note 1: Even if the STOP pin input is low after warm-up start, the STOP mode is not restarted.
Note 2: In this case of changing to the level-sensitive mode from the edge-sensitive mode, the release
mode is not switched until a rising edge of the STOP pin input is detected.
(2)
Edge-sensitive release mode (RELM = “0”)
In this mode, STOP mode is released by a rising edge of the STOP pin input. This is used in applications where a relatively short program is executed repeatedly at periodic intervals. This periodic
signal (for example, a clock from a low-power consumption oscillator) is input to the STOP pin. In
the edge-sensitive release mode, STOP mode is started even when the STOP pin input is high level.
Do not use any STOP3 to STOP0 pin input for releasing STOP mode in edge-sensitive release mode.
Example :Starting STOP mode from NORMAL mode
; IMF ← 0
DI
LD
(SYSCR1), 10010000B
; Starts after specified to the edge-sensitive release mode
VIH
STOP pin
XOUT pin
NORMAL
operation
STOP
operation
Warm up
NORMAL
operation
STOP mode started
by the program.
STOP
operation
STOP mode is released by the hardware at the rising
edge of STOP pin input.
Figure 2-8 Edge-sensitive Release Mode
Page 17
2. Operational Description
2.2 System Clock Controller
TMP86CH12MG
STOP mode is released by the following sequence.
1. In the dual-clock mode, when returning to NORMAL2, both the high-frequency and lowfrequency clock oscillators are turned on; when returning to SLOW1 mode, only the lowfrequency clock oscillator is turned on. In the single-clock mode, only the high-frequency
clock oscillator is turned on.
2. A warm-up period is inserted to allow oscillation time to stabilize. During warm up, all
internal operations remain halted. Four different warm-up times can be selected with the
SYSCR1<WUT> in accordance with the resonator characteristics.
3. When the warm-up time has elapsed, normal operation resumes with the instruction following the STOP mode start instruction.
Note 1: When the STOP mode is released, the start is made after the prescaler and the divider of the
timing generator are cleared to "0".
Note 2: STOP mode can also be released by inputting low level on the RESET pin, which immediately
performs the normal reset operation.
Note 3: When STOP mode is released with a low hold voltage, the following cautions must be observed.
The power supply voltage must be at the operating voltage level before releasing STOP mode.
The RESET pin input must also be “H” level, rising together with the power supply voltage. In this
case, if an external time constant circuit has been connected, the RESET pin input voltage will
increase at a slower pace than the power supply voltage. At this time, there is a danger that a
reset may occur if input voltage level of the RESET pin drops below the non-inverting high-level
input voltage (Hysteresis input).
Table 2-2 Warm-up Time Example (at fc = 16.0 MHz, fs = 32.768 kHz)
Warm-up Time [ms]
WUT
00
01
10
11
Return to NORMAL Mode
Return to SLOW Mode
12.288
4.096
3.072
1.024
750
250
5.85
1.95
Note 1: The warm-up time is obtained by dividing the basic clock by the divider. Therefore, the warm-up
time may include a certain amount of error if there is any fluctuation of the oscillation frequency
when STOP mode is released. Thus, the warm-up time must be considered as an approximate
value.
Page 18
Page 19
Figure 2-9 STOP Mode Start/Release
Divider
Instruction
execution
Program
counter
Main
system
clock
Oscillator
circuit
STOP pin
input
Divider
Instruction
execution
Program
counter
Main
system
clock
Oscillator
circuit
0
Halt
Turn off
Turn on
Turn on
n
Count up
a+3
Warm up
a+2
n+2
n+3
n+4
0
(b) STOP mode release
1
Instruction address a + 2
a+4
2
Instruction address a + 3
a+5
(a) STOP mode start (Example: Start with SET (SYSCR1). 7 instruction located at address a)
n+1
SET (SYSCR1). 7
a+3
3
Instruction address a + 4
a+6
0
Halt
Turn off
TMP86CH12MG
2. Operational Description
2.2 System Clock Controller
2.2.4.2
TMP86CH12MG
IDLE1/2 mode and SLEEP1/2 mode
IDLE1/2 and SLEEP1/2 modes are controlled by the system control register 2 (SYSCR2) and maskable
interrupts. The following status is maintained during these modes.
1. Operation of the CPU and watchdog timer (WDT) is halted. On-chip peripherals continue to
operate.
2. The data memory, CPU registers, program status word and port output latches are all held in the
status in effect before these modes were entered.
3. The program counter holds the address 2 ahead of the instruction which starts these modes.
Starting IDLE1/2 and
SLEEP1/2 modes by
instruction
CPU and WDT are halted
Yes
Reset input
Reset
No
No
Interrupt request
Yes
“0”
IMF
“1” (Interrupt release mode)
Normal
release mode
Interrupt processing
Execution of the instruction which follows the
IDLE1/2 and SLEEP1/2
modes start instruction
Figure 2-10 IDLE1/2 and SLEEP1/2 Modes
Page 20
TMP86CH12MG
• Start the IDLE1/2 and SLEEP1/2 modes
After IMF is set to "0", set the individual interrupt enable flag (EF) which releases IDLE1/2
and SLEEP1/2 modes. To start IDLE1/2 and SLEEP1/2 modes, set SYSCR2<IDLE> to “1”.
• Release the IDLE1/2 and SLEEP1/2 modes
IDLE1/2 and SLEEP1/2 modes include a normal release mode and an interrupt release mode.
These modes are selected by interrupt master enable flag (IMF). After releasing IDLE1/2 and
SLEEP1/2 modes, the SYSCR2<IDLE> is automatically cleared to “0” and the operation mode
is returned to the mode preceding IDLE1/2 and SLEEP1/2 modes.
IDLE1/2 and SLEEP1/2 modes can also be released by inputting low level on the RESET pin.
After releasing reset, the operation mode is started from NORMAL1 mode.
(1)
Normal release mode (IMF = “0”)
IDLE1/2 and SLEEP1/2 modes are released by any interrupt source enabled by the individual
interrupt enable flag (EF). After the interrupt is generated, the program operation is resumed from the
instruction following the IDLE1/2 and SLEEP1/2 modes start instruction. Normally, the interrupt
latches (IL) of the interrupt source used for releasing must be cleared to “0” by load instructions.
(2)
Interrupt release mode (IMF = “1”)
IDLE1/2 and SLEEP1/2 modes are released by any interrupt source enabled with the individual
interrupt enable flag (EF) and the interrupt processing is started. After the interrupt is processed, the
program operation is resumed from the instruction following the instruction, which starts IDLE1/2
and SLEEP1/2 modes.
Note: When a watchdog timer interrupts is generated immediately before IDLE1/2 and SLEEP1/2
modes are started, the watchdog timer interrupt will be processed but IDLE1/2 and SLEEP1/2
modes will not be started.
Page 21
Page 22
Figure 2-11 IDLE1/2 and SLEEP1/2 Modes Start/Release
Watchdog
timer
Instruction
execution
Program
counter
Interrupt
request
Main
system
clock
Watchdog
timer
Instruction
execution
Program
counter
Interrupt
request
Main
system
clock
Watchdog
timer
Instruction
execution
Program
counter
Interrupt
request
Main
system
clock
Halt
Halt
Halt
Halt
Operate
Operate
Operate
Acceptance of interrupt
Instruction address a + 2
a+4
(b) IDLE1/2 and SLEEP1/2 modes release
㽳㩷Interrupt release mode
a+3
㽲㩷Normal release mode
a+3
(a) IDLE1/2 and SLEEP1/2 modes start (Example: Starting with the SET instruction located at address a)
Operate
SET (SYSCR2). 4
a+2
Halt
a+3
2.2 System Clock Controller
2. Operational Description
TMP86CH12MG
TMP86CH12MG
2.2.4.3
IDLE0 and SLEEP0 modes (IDLE0, SLEEP0)
IDLE0 and SLEEP0 modes are controlled by the system control register 2 (SYSCR2) and the time base
timer control register (TBTCR). The following status is maintained during IDLE0 and SLEEP0 modes.
1. Timing generator stops feeding clock to peripherals except TBT.
2. The data memory, CPU registers, program status word and port output latches are all held in the
status in effect before IDLE0 and SLEEP0 modes were entered.
3. The program counter holds the address 2 ahead of the instruction which starts IDLE0 and
SLEEP0 modes.
Note: Before starting IDLE0 or SLEEP0 mode, be sure to stop (Disable) peripherals.
Stopping peripherals
by instruction
Starting IDLE0, SLEEP0
modes by instruction
CPU and WDT are halted
Reset input
Yes
Reset
No
No
TBT
source clock
falling
edge
Yes
No
TBTCR<TBTEN>
= "1"
Yes
No
TBT interrupt
enable
Yes
(Normal release mode)
No
IMF = "1"
Yes (Interrupt release mode)
Interrupt processing
Execution of the instruction
which follows the IDLE0,
SLEEP0 modes start
instruction
Figure 2-12 IDLE0 and SLEEP0 Modes
Page 23
2. Operational Description
2.2 System Clock Controller
TMP86CH12MG
• Start the IDLE0 and SLEEP0 modes
Stop (Disable) peripherals such as a timer counter.
To start IDLE0 and SLEEP0 modes, set SYSCR2<TGHALT> to “1”.
• Release the IDLE0 and SLEEP0 modes
IDLE0 and SLEEP0 modes include a normal release mode and an interrupt release mode.
These modes are selected by interrupt master flag (IMF), the individual interrupt enable flag
of TBT and TBTCR<TBTEN>.
After releasing IDLE0 and SLEEP0 modes, the SYSCR2<TGHALT> is automatically
cleared to “0” and the operation mode is returned to the mode preceding IDLE0 and SLEEP0
modes. Before starting the IDLE0 or SLEEP0 mode, when the TBTCR<TBTEN> is set to “1”,
INTTBT interrupt latch is set to “1”.
IDLE0 and SLEEP0 modes can also be released by inputting low level on the RESET pin.
After releasing reset, the operation mode is started from NORMAL1 mode.
Note: IDLE0 and SLEEP0 modes start/release without reference to TBTCR<TBTEN> setting.
(1)
Normal release mode (IMF•EF1•TBTCR<TBTEN> = “0”)
IDLE0 and SLEEP0 modes are released by the source clock falling edge, which is setting by the
TBTCR<TBTCK>. After the falling edge is detected, the program operation is resumed from the
instruction following the IDLE0 and SLEEP0 modes start instruction. Before starting the IDLE0 or
SLEEP0 mode, when the TBTCR<TBTEN> is set to “1”, INTTBT interrupt latch is set to “1”.
(2)
Interrupt release mode (IMF•EF1•TBTCR<TBTEN> = “1”)
IDLE0 and SLEEP0 modes are released by the source clock falling edge, which is setting by the
TBTCR<TBTCK> and INTTBT interrupt processing is started.
Note 1: Because returning from IDLE0, SLEEP0 to NORMAL1, SLOW1 is executed by the asynchronous internal clock, the period of IDLE0, SLEEP0 mode might be the shorter than the period setting by TBTCR<TBTCK>.
Note 2: When a watchdog timer interrupt is generated immediately before IDLE0/SLEEP0 mode is
started, the watchdog timer interrupt will be processed but IDLE0/SLEEP0 mode will not be
started.
Page 24
Page 25
Figure 2-13 IDLE0 and SLEEP0 Modes Start/Release
Watchdog
timer
Instruction
execution
Program
counter
TBT clock
Halt
Halt
Halt
Watchdog
timer
Main
system
clock
Halt
Instruction
execution
Program
counter
TBT clock
Main
system
clock
Watchdog
timer
Instruction
execution
Program
counter
Interrupt
request
Main
system
clock
a+3
Halt
Operate
Operate
(b) IDLE and SLEEP0 modes release
㽳㩷Interrupt release mode
a+3
㽲㩷Normal release mode
a+3
Acceptance of interrupt
Instruction address a + 2
a+4
(a) IDLE0 and SLEEP0 modes start (Example: Starting with the SET instruction located at address a
Operate
SET (SYSCR2). 2
a+2
TMP86CH12MG
2. Operational Description
2.2 System Clock Controller
2.2.4.4
TMP86CH12MG
SLOW mode
SLOW mode is controlled by the system control register 2 (SYSCR2).
The following is the methods to switch the mode with the warm-up counter.
(1)
Switching from NORMAL2 mode to SLOW1 mode
First, set SYSCR2<SYSCK> to switch the main system clock to the low-frequency clock for
SLOW2 mode. Next, clear SYSCR2<XEN> to turn off high-frequency oscillation.
Note: The high-frequency clock can be continued oscillation in order to return to NORMAL2 mode from
SLOW mode quickly. Always turn off oscillation of high-frequency clock when switching from
SLOW mode to stop mode.
Example 1 :Switching from NORMAL2 mode to SLOW1 mode.
SET
(SYSCR2). 5
; SYSCR2<SYSCK> ← 1
(Switches the main system clock to the low-frequency
clock for SLOW2)
CLR
(SYSCR2). 7
; SYSCR2<XEN> ← 0
(Turns off high-frequency oscillation)
Example 2 :Switching to the SLOW1 mode after low-frequency clock has stabilized.
SET
(SYSCR2). 6
; SYSCR2<XTEN> ← 1
LD
(TC3CR), 43H
; Sets mode for TC4, 3 (16-bit mode, fs for source)
LD
(TC4CR), 05H
; Sets warming-up counter mode
LDW
(TTREG3), 8000H
; Sets warm-up time (Depend on oscillator accompanied)
; IMF ← 0
DI
SET
(EIRH). 5
; IMF ← 1
EI
SET
; Enables INTTC4
(TC4CR). 3
; Starts TC4, 3
CLR
(TC4CR). 3
; Stops TC4, 3
SET
(SYSCR2). 5
; SYSCR2<SYSCK> ← 1
:
PINTTC4:
(Switches the main system clock to the low-frequency clock)
CLR
(SYSCR2). 7
; SYSCR2<XEN> ← 0
(Turns off high-frequency oscillation)
RETI
:
VINTTC4:
DW
PINTTC4
; INTTC4 vector table
Page 26
TMP86CH12MG
(2)
Switching from SLOW1 mode to NORMAL2 mode
First, set SYSCR2<XEN> to turn on the high-frequency oscillation. When time for stabilization
(Warm up) has been taken by the timer/counter (TC4,TC3), clear SYSCR2<SYSCK> to switch the
main system clock to the high-frequency clock.
SLOW mode can also be released by inputting low level on the RESET pin. After releasing reset, the
operation mode is started from NORMAL1 mode.
Note: After SYSCK is cleared to “0”, executing the instructions is continiued by the low-frequency clock
for the period synchronized with low-frequency and high-frequency clocks.
High-frequency clock
Low-frequency clock
Main system clock
SYSCK
Example :Switching from the SLOW1 mode to the NORMAL2 mode (fc = 16 MHz, warm-up time is 4.0 ms).
SET
(SYSCR2). 7
; SYSCR2<XEN> ← 1 (Starts high-frequency oscillation)
LD
(TC3CR), 63H
; Sets mode for TC4, 3 (16-bit mode, fc for source)
LD
(TC4CR), 05H
; Sets warming-up counter mode
LD
(TTREG4), 0F8H
; Sets warm-up time
; IMF ← 0
DI
SET
(EIRH). 5
; IMF ← 1
EI
SET
; Enables INTTC4
(TC4CR). 3
; Starts TC4, 3
CLR
(TC4CR). 3
; Stops TC4, 3
CLR
(SYSCR2). 5
; SYSCR2<SYSCK> ← 0
:
PINTTC4:
(Switches the main system clock to the high-frequency clock)
RETI
:
VINTTC4:
DW
PINTTC4
; INTTC4 vector table
Page 27
Page 28
Figure 2-14 Switching between the NORMAL2 and SLOW Modes
SET (SYSCR2). 7
SET (SYSCR2). 5
SLOW1 mode
Instruction
execution
XEN
SYSCK
Highfrequency
clock
Lowfrequency
clock
Main
system
clock
NORMAL2
mode
Instruction
execution
XEN
SYSCK
Highfrequency
clock
Lowfrequency
clock
Main
system
clock
(b) Switching to the NORMAL2 mode
Warm up during SLOW2 mode
CLR (SYSCR2). 5
(a) Switching to the SLOW mode
SLOW2 mode
CLR (SYSCR2). 7
NORMAL2
mode
SLOW1 mode
Turn off
2.2 System Clock Controller
2. Operational Description
TMP86CH12MG
TMP86CH12MG
2.3 Reset Circuit
The TMP86CH12MG has four types of reset generation procedures: An external reset input, an address trap reset,
a watchdog timer reset and a system clock reset. Of these reset, the address trap reset, the watchdog timer and the
system clock reset are a malfunction reset. When the malfunction reset request is detected, reset occurs during the
maximum 24/fc[s].
The malfunction reset circuit such as watchdog timer reset, address trap reset and system clock reset is not initialized when power is turned on. Therefore, reset may occur during maximum 24/fc[s] (1.5µs at 16.0 MHz) when
power is turned on.
Table 2-3 shows on-chip hardware initialization by reset action.
Table 2-3 Initializing Internal Status by Reset Action
On-chip Hardware
Initial Value
Program counter
(PC)
(FFFEH)
Stack pointer
(SP)
Not initialized
General-purpose registers
(W, A, B, C, D, E, H, L, IX, IY)
(JF)
Not initialized
Zero flag
(ZF)
Not initialized
Carry flag
(CF)
Not initialized
Half carry flag
(HF)
Not initialized
Sign flag
(SF)
Not initialized
Overflow flag
(VF)
Not initialized
(IMF)
0
(EF)
0
(IL)
0
Interrupt individual enable flags
Interrupt latches
2.3.1
Initial Value
Prescaler and divider of timing generator
0
Not initialized
Jump status flag
Interrupt master enable flag
On-chip Hardware
Watchdog timer
Enable
Output latches of I/O ports
Refer to I/O port circuitry
Control registers
Refer to each of control
register
RAM
Not initialized
External Reset Input
The RESET pin contains a Schmitt trigger (Hysteresis) with an internal pull-up resistor.
When the RESET pin is held at “L” level for at least 3 machine cycles (12/fc [s]) with the power supply voltage within the operating voltage range and oscillation stable, a reset is applied and the internal state is initialized.
When the RESET pin input goes high, the reset operation is released and the program execution starts at the
vector address stored at addresses FFFEH to FFFFH.
VDD
RESET
Internal reset
Watchdog timer reset
Malfunction
reset output
circuit
Address trap reset
System clock reset
Figure 2-15 Reset Circuit
Page 29
2. Operational Description
2.3 Reset Circuit
TMP86CH12MG
2.3.2
Address trap reset
If the CPU should start looping for some cause such as noise and an attempt be made to fetch an instruction
from the on-chip RAM (when WDTCR1<ATAS> is set to “1”), DBR or the SFR area, address trap reset will be
generated. The reset time is maximum 24/fc[s] (1.5µs at 16.0 MHz).
Note:The operating mode under address trapped is alternative of reset or interrupt. The address trap area is alternative.
Instruction
execution
Reset release
JP a
Instruction at address r
Address trap is occurred
Internal reset
4/fc to 12/fc [s]
maximum 24/fc [s]
16/fc [s]
Note 1: Address “a” is in the SFR, DBR or on-chip RAM (WDTCR1<ATAS> = “1”) space.
Note 2: During reset release, reset vector “r” is read out, and an instruction at address “r” is fetched and decoded.
Figure 2-16 Address Trap Reset
2.3.3
Watchdog timer reset
Refer to Section “Watchdog Timer”.
2.3.4
System clock reset
If the condition as follows is detected, the system clock reset occurs automatically to prevent dead lock of the
CPU. (The oscillation is continued without stopping.)
- In case of clearing SYSCR2<XEN> and SYSCR2<XTEN> simultaneously to “0”.
- In case of clearing SYSCR2<XEN> to “0”, when the SYSCR2<SYSCK> is “0”.
- In case of clearing SYSCR2<XTEN> to “0”, when the SYSCR2<SYSCK> is “1”.
The reset time is maximum 24/fc (1.5 µs at 16.0 MHz).
Page 30
TMP86CH12MG
Page 31
2. Operational Description
2.3 Reset Circuit
TMP86CH12MG
Page 32
TMP86CH12MG
3. Interrupt Control Circuit
The TMP86CH12MG has a total of 22 interrupt sources excluding reset. Interrupts can be nested with priorities.
Four of the internal interrupt sources are non-maskable while the rest are maskable.
Interrupt sources are provided with interrupt latches (IL), which hold interrupt requests, and independent vectors.
The interrupt latch is set to “1” by the generation of its interrupt request which requests the CPU to accept its interrupts. Interrupts are enabled or disabled by software using the interrupt master enable flag (IMF) and interrupt enable
flag (EF). If more than one interrupts are generated simultaneously, interrupts are accepted in order which is dominated by hardware. However, there are no prioritized interrupt factors among non-maskable interrupts.
Interrupt Factors
Internal/External
Enable Condition
Interrupt
Latch
Vector
Address
Priority
(Reset)
Non-maskable
–
FFFE
1
Internal
INTSWI (Software interrupt)
Non-maskable
–
FFFC
2
Internal
INTUNDEF (Executed the undefined instruction
interrupt)
Non-maskable
–
FFFC
2
Internal
INTATRAP (Address trap interrupt)
Non-maskable
IL2
FFFA
2
Internal
INTWDT (Watchdog timer interrupt)
Non-maskable
IL3
FFF8
2
Internal
INTEMG
IMF• EF4 = 1
IL4
FFF6
5
-
Reserved
IMF• EF5 = 1
IL5
FFF4
6
External
INT0
IMF• EF6 = 1, INT0EN = 1
IL6
FFF2
7
Internal
INTTC1
IMF• EF7 = 1
IL7
FFF0
8
External
INT1
IMF• EF8 = 1
IL8
FFEE
9
Internal
INTTBT
IMF• EF9 = 1
IL9
FFEC
10
External
INT2
IMF• EF10 = 1
IL10
FFEA
11
Internal
INTTC7T
IMF• EF11 = 1
IL11
FFE8
12
Reserved
IMF• EF12 = 1
IL12
FFE6
13
Internal
-
INTTC4
IMF• EF13 = 1
IL13
FFE4
14
Internal
INTTC3
IMF• EF14 = 1
IL14
FFE2
15
-
Reserved
IMF• EF15 = 1
IL15
FFE0
16
-
Reserved
IMF• EF16 = 1
IL16
FFBE
17
External
INT3
IMF• EF17 = 1
IL17
FFBC
18
Internal
INTSIO
IMF• EF18 = 1
IL18
FFBA
19
Internal
INTADC
IMF• EF19 = 1
IL19
FFB8
20
Internal
INTRXD
IMF• EF20 = 1
IL20
FFB6
21
Internal
INTTXD
IMF• EF21 = 1
IL21
FFB4
22
External
INT4
IMF• EF22 = 1
IL22
FFB2
23
Internal
INTTC7P
IMF• EF23 = 1
IL23
FFB0
24
-
Reserved
IMF• EF24 = 1
IL24
FFAE
25
-
Reserved
IMF• EF25 = 1
IL25
FFAC
26
Reserved
IMF• EF26 = 1
IL26
FFAA
27
Internal
-
INTRTC
IMF• EF27 = 1
IL27
FFA8
28
External
INT5
IMF• EF28 = 1
IL28
FFA6
29
-
Reserved
IMF• EF29 = 1
IL29
FFA4
30
-
Reserved
IMF• EF30 = 1
IL30
FFA2
31
-
Reserved
IMF• EF31 = 1
IL31
FFA0
32
Note 1: To use the address trap interrupt (INTATRAP), clear WDTCR1<ATOUT> to “0” (It is set for the “reset request” after reset is
cancelled). For details, see “Address Trap”.
Note 2: To use the watchdog timer interrupt (INTWDT), clear WDTCR1<WDTOUT> to "0" (It is set for the "Reset request" after
reset is released). For details, see "Watchdog Timer".
Page 33
3. Interrupt Control Circuit
3.1 Interrupt latches (IL28 to IL2)
TMP86CH12MG
3.1 Interrupt latches (IL28 to IL2)
An interrupt latch is provided for each interrupt source, except for a software interrupt and an executed the undefined instruction interrupt. When interrupt request is generated, the latch is set to “1”, and the CPU is requested to
accept the interrupt if its interrupt is enabled. The interrupt latch is cleared to "0" immediately after accepting interrupt. All interrupt latches are initialized to “0” during reset.
The interrupt latches are located on address 002EH, 002FH, 003CH and 003DH in SFR area. Each latch can be
cleared to "0" individually by instruction. However, IL2 and IL3 should not be cleared to "0" by software. For clearing the interrupt latch, load instruction should be used and then IL2 and IL3 should be set to "1". If the read-modifywrite instructions such as bit manipulation or operation instructions are used, interrupt request would be cleared
inadequately if interrupt is requested while such instructions are executed.
Interrupt latches are not set to “1” by an instruction.
Since interrupt latches can be read, the status for interrupt requests can be monitored by software.
Note: In main program, before manipulating the interrupt enable flag (EF) or the interrupt latch (IL), be sure to clear IMF to
"0" (Disable interrupt by DI instruction). Then set IMF newly again as required after operating on the EF or IL
(Enable interrupt by EI instruction)
In interrupt service routine, because the IMF becomes "0" automatically, clearing IMF need not execute normally on
interrupt service routine. However, if using multiple interrupt on interrupt service routine, manipulating EF or IL
should be executed before setting IMF="1".
Example 1 :Clears interrupt latches
; IMF ← 0
DI
LDW
(ILL), 1110100000111111B
; IL12, IL10 to IL6 ← 0
; IMF ← 1
EI
Example 2 :Reads interrupt latchess
WA, (ILL)
; W ← ILH, A ← ILL
TEST
(ILL). 7
; if IL7 = 1 then jump
JR
F, SSET
LD
Example 3 :Tests interrupt latches
3.2 Interrupt enable register (EIR)
The interrupt enable register (EIR) enables and disables the acceptance of interrupts, except for the non-maskable
interrupts (Software interrupt, undefined instruction interrupt, address trap interrupt and watchdog interrupt). Nonmaskable interrupt is accepted regardless of the contents of the EIR.
The EIR consists of an interrupt master enable flag (IMF) and the individual interrupt enable flags (EF). These
registers are located on address 002CH, 002DH, 003AH and 003BH in SFR area, and they can be read and written
by an instructions (Including read-modify-write instructions such as bit manipulation or operation instructions).
3.2.1
Interrupt master enable flag (IMF)
The interrupt enable register (IMF) enables and disables the acceptance of the whole maskable interrupt.
While IMF = “0”, all maskable interrupts are not accepted regardless of the status on each individual interrupt
enable flag (EF). By setting IMF to “1”, the interrupt becomes acceptable if the individuals are enabled. When
an interrupt is accepted, IMF is cleared to “0” after the latest status on IMF is stacked. Thus the maskable interrupts which follow are disabled. By executing return interrupt instruction [RETI/RETN], the stacked data,
which was the status before interrupt acceptance, is loaded on IMF again.
The IMF is located on bit0 in EIRL (Address: 003AH in SFR), and can be read and written by an instruction.
The IMF is normally set and cleared by [EI] and [DI] instruction respectively. During reset, the IMF is initialized to “0”.
Page 34
TMP86CH12MG
3.2.2
Individual interrupt enable flags (EF28 to EF4)
Each of these flags enables and disables the acceptance of its maskable interrupt. Setting the corresponding
bit of an individual interrupt enable flag to “1” enables acceptance of its interrupt, and setting the bit to “0” disables acceptance. During reset, all the individual interrupt enable flags (EF28 to EF4) are initialized to “0” and
all maskable interrupts are not accepted until they are set to “1”.
Note:In main program, before manipulating the interrupt enable flag (EF) or the interrupt latch (IL), be sure to clear
IMF to "0" (Disable interrupt by DI instruction). Then set IMF newly again as required after operating on the EF
or IL (Enable interrupt by EI instruction)
In interrupt service routine, because the IMF becomes "0" automatically, clearing IMF need not execute normally on interrupt service routine. However, if using multiple interrupt on interrupt service routine, manipulating EF or IL should be executed before setting IMF="1".
Example 1 :Enables interrupts individually and sets IMF
; IMF ← 0
DI
LDW
:
(EIRL), 1110100010100000B
; EF15 to EF13, EF11, EF7, EF5 ← 1
Note: IMF should not be set.
:
; IMF ← 1
EI
Example 2 :C compiler description example
unsigned int _io (3AH) EIRL;
/* 3AH shows EIRL address */
_DI();
EIRL = 10100000B;
:
_EI();
Page 35
3. Interrupt Control Circuit
3.2 Interrupt enable register (EIR)
TMP86CH12MG
Interrupt Latches
(Initial value: *00*0000 00*000**)
ILH,ILL
(003DH, 003CH)
15
14
13
12
11
10
9
8
7
6
5
4
3
2
−
IL14
IL13
−
IL11
IL10
IL9
IL8
IL7
IL6
−
IL4
IL3
IL2
ILH (003DH)
1
0
ILL (003CH)
(Initial value: ***00*** 0000000*)
ILD,ILE
(002FH, 002EH)
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
−
−
−
IL28
IL27
−
−
−
IL23
IL22
IL21
IL20
IL19
IL18
IL17
−
ILD (002FH)
IL28 to IL2
ILE (002EH)
at RD
0: No interrupt request
Interrupt latches
at WR
0: Clears the interrupt request
1: (Interrupt latch is not set.)
1: Interrupt request
R/W
Note 1: To clear any one of bits IL7 to IL4, be sure to write "1" into IL2 and IL3.
Note 2: In main program, before manipulating the interrupt enable flag (EF) or the interrupt latch (IL), be sure to clear IMF to "0"
(Disable interrupt by DI instruction). Then set IMF newly again as required after operating on the EF or IL (Enable interrupt
by EI instruction)
In interrupt service routine, because the IMF becomes "0" automatically, clearing IMF need not execute normally on interrupt service routine. However, if using multiple interrupt on interrupt service routine, manipulating EF or IL should be executed before setting IMF="1".
Note 3: Do not clear IL with read-modify-write instructions such as bit operations.
Interrupt Enable Registers
(Initial value: *00*0000 00*0***0)
EIRH,EIRL
(003BH, 003AH)
15
14
13
−
EF14
EF13
12
11
10
9
8
7
6
5
−
EF11
EF10
EF9
EF8
EF7
EF6
−
EIRH (003BH)
4
3
2
1
EF4
0
IMF
EIRL (003AH)
(Initial value: ***00*** 0000000*)
EIRD,EIRE
(002DH, 002CH)
15
14
13
−
−
−
12
11
10
9
8
7
6
5
EF28
EF27
−
−
−
EF23
EF22
EF21
EIRD (002DH)
EF28 to EF4
IMF
4
3
2
1
0
EF20
EF19
EF18
EF17
−
EIRE (002CH)
Individual-interrupt enable flag
(Specified for each bit)
0:
1:
Disables the acceptance of each maskable interrupt.
Enables the acceptance of each maskable interrupt.
Interrupt master enable flag
0:
1:
Disables the acceptance of all maskable interrupts
Enables the acceptance of all maskable interrupts
R/W
Note 1: *: Don’t care
Note 2: Do not set IMF and the interrupt enable flag (EF15 to EF4) to “1” at the same time.
Note 3: In main program, before manipulating the interrupt enable flag (EF) or the interrupt latch (IL), be sure to clear IMF to "0"
(Disable interrupt by DI instruction). Then set IMF newly again as required after operating on the EF or IL (Enable interrupt
by EI instruction)
In interrupt service routine, because the IMF becomes "0" automatically, clearing IMF need not execute normally on interrupt service routine. However, if using multiple interrupt on interrupt service routine, manipulating EF or IL should be executed before setting IMF="1".
Page 36
TMP86CH12MG
3.3 Interrupt Sequence
An interrupt request, which raised interrupt latch, is held, until interrupt is accepted or interrupt latch is cleared to
“0” by resetting or an instruction. Interrupt acceptance sequence requires 8 machine cycles (2 µs @16 MHz) after the
completion of the current instruction. The interrupt service task terminates upon execution of an interrupt return
instruction [RETI] (for maskable interrupts) or [RETN] (for non-maskable interrupts). Figure 3-1 shows the timing
chart of interrupt acceptance processing.
3.3.1
Interrupt acceptance processing is packaged as follows.
a. The interrupt master enable flag (IMF) is cleared to “0” in order to disable the acceptance of any following interrupt.
b. The interrupt latch (IL) for the interrupt source accepted is cleared to “0”.
c. The contents of the program counter (PC) and the program status word, including the interrupt master
enable flag (IMF), are saved (Pushed) on the stack in sequence of PSW + IMF, PCH, PCL. Meanwhile, the stack pointer (SP) is decremented by 3.
d. The entry address (Interrupt vector) of the corresponding interrupt service program, loaded on the vector table, is transferred to the program counter.
e. The instruction stored at the entry address of the interrupt service program is executed.
Note:When the contents of PSW are saved on the stack, the contents of IMF are also saved.
Interrupt service task
1-machine cycle
Interrupt
request
Interrupt
latch (IL)
IMF
Execute
instruction
PC
SP
Execute
instruction
a−1
a
Execute
instruction
Interrupt acceptance
a+1
b
a
b+1 b+2 b + 3
n−1 n−2
n
Execute RETI instruction
c+2
c+1
a
n−2 n−1
n-3
a+1 a+2
n
Note 1: a: Return address entry address, b: Entry address, c: Address which RETI instruction is stored
Note 2: On condition that interrupt is enabled, it takes 38/fc [s] or 38/fs [s] at maximum (If the interrupt latch is set at the first
machine cycle on 10 cycle instruction) to start interrupt acceptance processing since its interrupt latch is set.
Figure 3-1 Timing Chart of Interrupt Acceptance/Return Interrupt Instruction
Example: Correspondence between vector table address for INTTBT and the entry address of the interrupt
service program
Vector table address
FFECH
03H
FFEDH
D2H
Entry address
Vector
D203H
0FH
D204H
06H
Figure 3-2 Vector table address,Entry address
Page 37
Interrupt
service
program
3. Interrupt Control Circuit
3.3 Interrupt Sequence
TMP86CH12MG
A maskable interrupt is not accepted until the IMF is set to “1” even if the maskable interrupt higher than the
level of current servicing interrupt is requested.
In order to utilize nested interrupt service, the IMF is set to “1” in the interrupt service program. In this case,
acceptable interrupt sources are selectively enabled by the individual interrupt enable flags.
To avoid overloaded nesting, clear the individual interrupt enable flag whose interrupt is currently serviced,
before setting IMF to “1”. As for non-maskable interrupt, keep interrupt service shorten compared with length
between interrupt requests; otherwise the status cannot be recovered as non-maskable interrupt would simply
nested.
3.3.2
Saving/restoring general-purpose registers
During interrupt acceptance processing, the program counter (PC) and the program status word (PSW,
includes IMF) are automatically saved on the stack, but the accumulator and others are not. These registers are
saved by software if necessary. When multiple interrupt services are nested, it is also necessary to avoid using
the same data memory area for saving registers. The following methods are used to save/restore the generalpurpose registers.
3.3.2.1
Using PUSH and POP instructions
If only a specific register is saved or interrupts of the same source are nested, general-purpose registers
can be saved/restored using the PUSH/POP instructions.
Example :Save/store register using PUSH and POP instructions
PINTxx:
PUSH
WA
; Save WA register
(interrupt processing)
POP
WA
; Restore WA register
RETI
; RETURN
Address
(Example)
SP
b-5
A
SP
b-4
SP
b-3
PCL
W
PCL
PCH
PCH
PCH
PSW
PSW
PSW
At acceptance of
an interrupt
At execution of
PUSH instruction
PCL
At execution of
POP instruction
b-2
b-1
SP
b
At execution of
RETI instruction
Figure 3-3 Save/store register using PUSH and POP instructions
3.3.2.2
Using data transfer instructions
To save only a specific register without nested interrupts, data transfer instructions are available.
Page 38
TMP86CH12MG
Example :Save/store register using data transfer instructions
PINTxx:
LD
(GSAVA), A
; Save A register
(interrupt processing)
LD
A, (GSAVA)
; Restore A register
RETI
; RETURN
Main task
Interrupt
service task
Interrupt
acceptance
Saving
registers
Restoring
registers
Interrupt return
Saving/Restoring general-purpose registers using PUSH/POP data transfer instruction
Figure 3-4 Saving/Restoring General-purpose Registers under Interrupt Processing
3.3.3
Interrupt return
Interrupt return instructions [RETI]/[RETN] perform as follows.
[RETI]/[RETN] Interrupt Return
1. Program counter (PC) and program status word
(PSW, includes IMF) are restored from the stack.
2. Stack pointer (SP) is incremented by 3.
As for address trap interrupt (INTATRAP), it is required to alter stacked data for program counter (PC) to
restarting address, during interrupt service program.
Note:If [RETN] is executed with the above data unaltered, the program returns to the address trap area and
INTATRAP occurs again.When interrupt acceptance processing has completed, stacked data for PCL and
PCH are located on address (SP + 1) and (SP + 2) respectively.
Example 1 :Returning from address trap interrupt (INTATRAP) service program
PINTxx:
POP
WA
; Recover SP by 2
LD
WA, Return Address
;
PUSH
WA
; Alter stacked data
(interrupt processing)
RETN
; RETURN
Page 39
3. Interrupt Control Circuit
3.4 Software Interrupt (INTSW)
TMP86CH12MG
Example 2 :Restarting without returning interrupt
(In this case, PSW (Includes IMF) before interrupt acceptance is discarded.)
PINTxx:
INC
SP
; Recover SP by 3
INC
SP
;
INC
SP
;
(interrupt processing)
LD
EIRL, data
; Set IMF to “1” or clear it to “0”
JP
Restart Address
; Jump into restarting address
Interrupt requests are sampled during the final cycle of the instruction being executed. Thus, the next interrupt can be accepted immediately after the interrupt return instruction is executed.
Note 1: It is recommended that stack pointer be return to rate before INTATRAP (Increment 3 times), if return interrupt instruction [RETN] is not utilized during interrupt service program under INTATRAP (such as Example
2).
Note 2: When the interrupt processing time is longer than the interrupt request generation time, the interrupt service
task is performed but not the main task.
3.4 Software Interrupt (INTSW)
Executing the SWI instruction generates a software interrupt and immediately starts interrupt processing (INTSW
is highest prioritized interrupt).
Use the SWI instruction only for detection of the address error or for debugging.
3.4.1
Address error detection
FFH is read if for some cause such as noise the CPU attempts to fetch an instruction from a non-existent
memory address during single chip mode. Code FFH is the SWI instruction, so a software interrupt is generated and an address error is detected. The address error detection range can be further expanded by writing
FFH to unused areas of the program memory. Address trap reset is generated in case that an instruction is
fetched from RAM, DBR or SFR areas.
3.4.2
Debugging
Debugging efficiency can be increased by placing the SWI instruction at the software break point setting
address.
3.5 Undefined Instruction Interrupt (INTUNDEF)
Taking code which is not defined as authorized instruction for instruction causes INTUNDEF. INTUNDEF is generated when the CPU fetches such a code and tries to execute it. INTUNDEF is accepted even if non-maskable interrupt is in process. Contemporary process is broken and INTUNDEF interrupt process starts, soon after it is
requested.
Note: The undefined instruction interrupt (INTUNDEF) forces CPU to jump into vector address, as software interrupt
(SWI) does.
3.6 Address Trap Interrupt (INTATRAP)
Fetching instruction from unauthorized area for instructions (Address trapped area) causes reset output or address
trap interrupt (INTATRAP). INTATRAP is accepted even if non-maskable interrupt is in process. Contemporary process is broken and INTATRAP interrupt process starts, soon after it is requested.
Note: The operating mode under address trapped, whether to be reset output or interrupt processing, is selected on
watchdog timer control register (WDTCR).
Page 40
TMP86CH12MG
3.7 External Interrupts
The TMP86CH12MG has 6 external interrupt inputs. These inputs are equipped with digital noise reject circuits
(Pulse inputs of less than a certain time are eliminated as noise).
Edge selection is also possible with INT1 to INT4. The INT0/P31 pin can be configured as either an external interrupt input pin or an input/output port, and is configured as an input port during reset.
Edge selection, noise reject control and INT0/P31 pin function selection are performed by the external interrupt
control register (EINTCR).
Source
INT0
INT1
INT2
INT3
INT4
INT5
Pin
INT0
INT1
INT2
INT3
INT4
INT5
Enable Conditions
Release Edge (level)
Digital Noise Reject
IMF ΠEF6 ΠINT0EN=1
Falling edge
Pulses of less than 2/fc [s] are eliminated as
noise. Pulses of 7/fc [s] or more are considered
to be signals. In the SLOW or the SLEEP mode,
pulses of less than 1/fs [s] are eliminated as
noise. Pulses of 3.5/fs [s] or more are considered to be signals.
IMF ΠEF8 = 1
Falling edge
or
Rising edge
Pulses of less than 15/fc or 63/fc [s] are eliminated as noise. Pulses of 49/fc or 193/fc [s] or
more are considered to be signals. In the SLOW
or the SLEEP mode, pulses of less than 1/fs [s]
are eliminated as noise. Pulses of 3.5/fs [s] or
more are considered to be signals.
IMF ΠEF10 = 1
Falling edge
or
Rising edge
Pulses of less than 7/fc [s] are eliminated as
noise. Pulses of 25/fc [s] or more are considered
to be signals. In the SLOW or the SLEEP mode,
pulses of less than 1/fs [s] are eliminated as
noise. Pulses of 3.5/fs [s] or more are considered to be signals.
IMF ΠEF17 = 1
Falling edge
or
Rising edge
Pulses of less than 7/fc [s] are eliminated as
noise. Pulses of 25/fc [s] or more are considered
to be signals. In the SLOW or the SLEEP mode,
pulses of less than 1/fs [s] are eliminated as
noise. Pulses of 3.5/fs [s] or more are considered to be signals.
IMF ΠEF22 = 1
Falling edge,
Rising edge,
Falling and Rising edge
or
H level
Pulses of less than 7/fc [s] are eliminated as
noise. Pulses of 25/fc [s] or more are considered
to be signals. In the SLOW or the SLEEP mode,
pulses of less than 1/fs [s] are eliminated as
noise. Pulses of 3.5/fs [s] or more are considered to be signals.
Falling edge
Pulses of less than 2/fc [s] are eliminated as
noise. Pulses of 7/fc [s] or more are considered
to be signals. In the SLOW or the SLEEP mode,
pulses of less than 1/fs [s] are eliminated as
noise. Pulses of 3.5/fs [s] or more are considered to be signals.
IMF ΠEF28 = 1
Note 1: In NORMAL1/2 or IDLE1/2 mode, if a signal with no noise is input on an external interrupt pin, it takes a maximum of "signal establishment time + 6/fs[s]" from the input signal's edge to set the interrupt latch.
Note 2: When INT0EN = "0", IL6 is not set even if a falling edge is detected on the INT0 pin input.
Note 3: When a pin with more than one function is used as an output and a change occurs in data or input/output status, an interrupt request signal is generated in a pseudo manner. In this case, it is necessary to perform appropriate processing such
as disabling the interrupt enable flag.
Page 41
3. Interrupt Control Circuit
3.7 External Interrupts
TMP86CH12MG
External Interrupt Control Register
EINTCR
7
6
(0037H)
INT1NC
INT0EN
5
4
INT4ES
3
2
1
INT3ES
INT2ES
INT1ES
0
(Initial value: 0000 000*)
INT1NC
Noise reject time select
0: Pulses of less than 63/fc [s] are eliminated as noise
1: Pulses of less than 15/fc [s] are eliminated as noise
R/W
INT0EN
P31/INT0 pin configuration
0: P31 input/output port
1: INT0 pin (Port P31 should be set to an input mode)
R/W
INT4 ES
INT4 edge select
00: Rising edge
01: Falling edge
10: Rising edge and Falling edge
11: H level
R/W
INT3 ES
INT3 edge select
0: Rising edge
1: Falling edge
R/W
INT2 ES
INT2 edge select
0: Rising edge
1: Falling edge
R/W
INT1 ES
INT1 edge select
0: Rising edge
1: Falling edge
R/W
Note 1: fc: High-frequency clock [Hz], *: Don’t care
Note 2: When the system clock frequency is switched between high and low or when the external interrupt control register
(EINTCR) is overwritten, the noise canceller may not operate normally. It is recommended that external interrupts are disabled using the interrupt enable register (EIR).
Note 3: The maximum time from modifying INT1NC until a noise reject time is changed is 26/fc.
Note 4: In case RESET pin is released while the state of INT4 pin keeps "H" level, the external interrupt 4 request is not generated
even if the INT4 edge select is specified as "H" level. The rising edge is needed after RESET pin is released.
Page 42
TMP86CH12MG
4. Special Function Register (SFR)
The TMP86CH12MG adopts the memory mapped I/O system, and all peripheral control and data transfers are performed through the special function register (SFR) or the data buffer register (DBR). The SFR is mapped on address
0000H to 003FH, DBR is mapped on address 0F80H to 0FFFH.
This chapter shows the arrangement of the special function register (SFR) and data buffer register (DBR) for
TMP86CH12MG.
4.1 SFR
Address
Read
Write
0000H
P0DR
0001H
P1DR
0002H
P2DR
0003H
P3DR
0004H
P0OUTCR
0005H
P1CR
0006H
P3CR1
0007H
P3CR2
0008H
TC7DRAL
0009H
TC7DRAH
000AH
TC7DRBL
000BH
TC7DRBH
000CH
TC7DRCL
000DH
TC7DRCH
000EH
P0PRD
000FH
P2PRD
-
0010H
TC1DRAL
0011H
TC1DRAH
0012H
TC1DRBL
0013H
TC1DRBH
0014H
TC1CR
0015H
TC3CR
0016H
TC4CR
0017H
PWREG3
0018H
PWREG4
0019H
TTREG3
001AH
TTREG4
001BH
RTCCR
001CH
Reserved
001DH
Reserved
001EH
Reserved
001FH
ADCDR2
-
0020H
ADCDR1
-
0021H
UARTSR
UARTCR1
0022H
-
UARTCR2
0023H
Reserved
0024H
Reserved
0025H
ADCCR1
Page 43
4. Special Function Register (SFR)
4.1 SFR
TMP86CH12MG
Address
Read
Write
0026H
ADCCR2
0027H
Reserved
0028H
Reserved
0029H
TC7CR1
002AH
TC7CR2
002BH
TC7CR3
002CH
EIRE
002DH
EIRD
002EH
ILE
002FH
ILD
0030H
Reserved
0031H
-
0032H
SIOSR
0033H
SIOCR1
SIOCR2
Reserved
0034H
-
WDTCR1
0035H
-
WDTCR2
0036H
TBTCR
0037H
EINTCR
0038H
SYSCR1
0039H
SYSCR2
003AH
EIRL
003BH
EIRH
003CH
ILL
003DH
ILH
003EH
Reserved
003FH
PSW
Note 1: Do not access reserved areas by the program.
Note 2: − ; Cannot be accessed.
Note 3: Write-only registers and interrupt latches cannot use the read-modify-write instructions (Bit manipulation instructions such
as SET, CLR, etc. and logical operation instructions such as AND, OR, etc.).
Page 44
TMP86CH12MG
4.2 DBR
Address
Read
Write
0F80H
SIOBR0
0F81H
SIOBR1
0F82H
SIOBR2
0F83H
SIOBR3
0F84H
SIOBR4
0F85H
SIOBR5
0F86H
SIOBR6
0F87H
SIOBR7
0F88H
-
STOPCR
0F89H
RDBUF
TDBUF
0F8AH
Reserved
0F8BH
Reserved
0F8CH
Reserved
0F8DH
Reserved
0F8EH
Reserved
0F8FH
Reserved
0F90H
Reserved
0F91H
Reserved
0F92H
Reserved
0F93H
Reserved
0F94H
Reserved
0F95H
Reserved
0F96H
Reserved
0F97H
Reserved
0F98H
Reserved
0F99H
Reserved
0F9AH
Reserved
0F9BH
Reserved
0F9CH
Reserved
0F9DH
Reserved
0F9EH
Reserved
0F9FH
Reserved
Page 45
4. Special Function Register (SFR)
4.2 DBR
TMP86CH12MG
Address
Read
Write
0FA0H
Reserved
0FA1H
Reserved
0FA2H
Reserved
0FA3H
Reserved
0FA4H
Reserved
0FA5H
Reserved
0FA6H
Reserved
0FA7H
Reserved
0FA8H
Reserved
0FA9H
Reserved
0FAAH
Reserved
0FABH
Reserved
0FACH
Reserved
0FADH
Reserved
0FAEH
Reserved
0FAFH
Reserved
0FB0H
TC7DRDL
0FB1H
TC7DRDH
0FB2H
TC7DREL
0FB3H
TC7DREH
0FB4H
TC7CAPAL
-
0FB5H
TC7CAPAH
-
0FB6H
TC7CAPBL
-
0FB7H
TC7CAPBH
-
0FB8H
Reserved
0FB9H
Reserved
0FBAH
Reserved
0FBBH
Reserved
0FBCH
Reserved
0FBDH
Reserved
0FBEH
Reserved
0FBFH
Reserved
Address
Read
0FC0H
Write
Reserved
: :
: :
0FDFH
Reserved
Address
Read
0FE0H
Write
Reserved
: :
: :
0FFFH
Reserved
Note 1: Do not access reserved areas by the program.
Note 2: − ; Cannot be accessed.
Note 3: Write-only registers and interrupt latches cannot use the read-modify-write instructions (Bit manipulation instructions such
as SET, CLR, etc. and logical operation instructions such as AND, OR, etc.).
Page 46
TMP86CH12MG
5. I/O Ports
The TMP86CH12MG has 4 parallel input/output ports (24 pins) as follows.
Primary Function
Secondary Functions
Port P0
8-bit I/O port
External interrupt, serial interface input/output, UART input/output and timer
counter input/output.
Port P1
5-bit I/O port
External interrupt and timer counter input/output.
Port P2
3-bit I/O port
Low-frequency resonator connections, external interrupt input, STOP mode
release signal input.
Port P3
8-bit I/O port
External interrupt, analog input and STOP mode release signal input.
Each output port contains a latch, which holds the output data. All input ports do not have latches, so the external
input data should be externally held until the input data is read from outside or reading should be performed several
timer before processing. Figure 5-1 shows input/output timing examples.
External data is read from an I/O port in the S1 state of the read cycle during execution of the read instruction. This
timing cannot be recognized from outside, so that transient input such as chattering must be processed by the program.
Output data changes in the S2 state of the write cycle during execution of the instruction which writes to an I/O
port.
Fetch cycle
S0
Instruction execution cycle
S1
S2 S3
Example: LD
Fetch cycle
S0
S1 S2
S3
Read cycle
S0 S1
S2
S3
A, (x)
Input strobe
Data input
(a) Input timing
Fetch cycle
S0
Instruction execution cycle
S1
S2 S3
Example: LD
Fetch cycle
S0
S1 S2
S3
Write cycle
S0 S1
S2
S3
(x), A
Output strobe
Old
Data output
(b) Output timing
Note: The positions of the read and write cycles may vary, depending on the instruction.
Figure 5-1 Input/Output Timing (Example)
Page 47
New
5. I/O Ports
5.1 Port P0 (P07 to P00)
TMP86CH12MG
5.1 Port P0 (P07 to P00)
Port P0 is an 8-bit input/output port.
Port P0 is also used as an external interrupt input, a serial interface input/output, an UART input/output and a
timer/counter input/output.
It can be selected whether output circuit of P0 port is a C-MOS output or a sink open drain individually, by setting
P0OUTCR. During reset, the P0DR is initialized to "1", and the P0OUTCR is initialized to "0". When a corresponding bit of P0OUTCR is "0". the output circuit is selected to a sink open drain and when a corresponding bit of
P0OUTCR is "1", the output circuit is selected to a C-MOS output.
When used as an input port, an external interrupt input, a serial interface input ,an UART input and a timer/counter
input , the corresponding output control (P0OUTCR) should be set to "0" after P0DR is set to "1".
When using this port as a PPG1 and/or PPG2 output, set the output latch (P0DR), and then set the P0OUTCR.
Next, set the PPG output initial value in the PPG1INI and/or PPG2INI, and set the PPG1OE and/or PPG2OE to "1"
to enable PPG output. At this time, the output latch (P0DR) should be set to the same value as the PPG output initial
value in the PPG1INI, PPG2INI.
During reset, the P0DR is initialized to "1", and the P0OUTCR is initialized to "0".
P0 port output latch (P0DR) and P0 port terminal input (P0PRD) are located on their respective address.
When read the output latch data, the P0DR should be read. When read the terminal input data, the P0PRD register
should be read.
Table 5-1
Register Programming for Multi-function Ports (P07 to P00)
Programmed Value
Function
P0DR
P0OUTCR
Port input, external interrupt input, serial interface input, timer counter input or UART input
“1”
“0”
Port “0” output
“0”
Port “1” output, serial interface output or UART output
“1”
Set to the same value as
PPG1INI and PPG2INI
Timer counter 7 output
Page 48
Programming for each
applications
TMP86CH12MG
STOP
OUTEN
P0OUTCRi
D
Q
P0OUTCRi KPRWV
&CVCKPRWV (P0PRD)
17VRWVNCVEJTGCF (P0DR)
&CVCQWVRWV (P0DR)
%QPVTQNQWVRWV
D
Q
P0i
1WVRWVNCVEJ
%QPVTQNKPRWV
STOP
OUTEN
P0OUTCRj
D
Q
P0OUTCRj ౉ജ
&CVCKPRWV (P0PRD)
1WVRWVNCVEJTGCF (P0DR)
Data output (P0DR)
22)M
22)M+0+
22)M1'
%QPVTQNKPRWV
D
A
Q
1WVRWVNCVEJ
B
P0j
S
Note: i = 5 to 0, j = 7 and 6, k = 2 and 1
Figure 5-2 Port 0
Page 49
5. I/O Ports
5.1 Port P0 (P07 to P00)
P0DR
(0000H)
R/W
TMP86CH12MG
7
6
P07
PPG2
INT2
P06
PPG1
INT1
5
4
3
2
1
0
P05
TC7
P04
SO
P03
SI
P02
SCK
P01
RXD
P00
TXD
(Initial value: 0000 0000)
P0OUTCR
(0004H)
P0OUTCR
P0PRD
(0008H)
Read only
(Initial value: 1111 1111)
P07
Port P0 output circuit control (Set for each bit individually)
P06
P05
P04
P03
P02
Page 50
P01
0: Sink open-drain output
1: C-MOS output
P00
R/W
TMP86CH12MG
5.2 Port P1 (P17 to P10)
Port P1 is an 5-bit input/output port which can be configured as an input or output in one-bit unit.
Port P1 is also used as a timer/counter input/output, an external interrupt input and a divider output.
Input/output mode is specified by the P1 control register (P1CR).
During reset, the P1CR is initialized to "0" and port P1 becomes an input mode. And the P1DR is initialized to "0".
When used as an input port, a timer/counter input and an external interrupt input, the corresponding bit of P1CR
should be set to "0".
When used as an output port, the corresponding bit of P1CR should be set to "1".
When used as a timer/counter output and a divider output, P1DR is set to "1" beforehand and the corresponding bit
of P1CR should be set to "1".
When P1CR is "1", the content of the corresponding output latch is read by reading P1DR. If a read instruction is
executed for the P1DR and P1CR, read data of bits 7 to 5 are unstable.
Table 5-2 Register Programming for Multi-function Ports
Programmed Value
Function
P1DR
P1CR
*
“0”
Port “0” output
“0”
“1”
Port “1” output, a timer output or a divider output
“1”
“1”
Port input, timer/counter input or external interrupt input
Note: Asterisk (*) indicates “1” or “0” either of which can be selected.
STOP
OUTEN
P1CRi
D
Q
D
Q
P1CRi input
Data input (P1DR)
Data output (P1DR)
P1i
Output latch
Control output
Control input
Note: i = 7 to 0
Figure 5-3 Port 1
Note: The port set to an input mode reads the terminal input data. Therefore, when the input and output modes are used
together, the content of the output latch which is specified as input mode might be changed by executing a bit
Manipulation instruction.
Page 51
5. I/O Ports
5.2 Port P1 (P17 to P10)
TMP86CH12MG
7
6
5
P1DR
(0001H)
R/W
P1CR
(0005H)
7
6
5
4
3
2
1
0
P14
TC1
P13
P12
PPG
DVO
P11
TC4
PWM4
PDO4
PPG4
P10
TC3
PWM3
PDO3
INT4
INT3
4
3
1
0
2
(Initial value: ***0 0000)
(Initial value: ***0 0000)
P1CR
I/O control for port P1 (Specified for each bit)
Page 52
0: Input mode
1: Output mode
R/W
TMP86CH12MG
5.3 Port P2 (P22 to P20)
Port P2 is a 3-bit input/output port.
It is also used as an external interrupt, a STOP mode release signal input, and low-frequency crystal oscillator connection pins. When used as an input port or a secondary function pins, respective output latch (P2DR) should be set
to “1”.
During reset, the P2DR is initialized to “1”.
A low-frequency crystal oscillator (32.768 kHz) is connected to pins P21 (XTIN) and P22 (XTOUT) in the dualclock mode. In the single-clock mode, pins P21 and P22 can be used as normal input/output ports.
It is recommended that pin P20 should be used as an external interrupt input, a STOP mode release signal input, or
an input port. If it is used as an output port, the interrupt latch is set on the falling edge of the output pulse.
P2 port output latch (P2DR) and P2 port terminal input (P2PRD) are located on their respective address.
When read the output latch data, the P2DR should be read and when read the terminal input data, the P2PRD register should be read. If a read instruction is executed for port P2, read data of bits 7 to 3 are unstable.
Data input (P20PRD)
Data input (P20)
Data output (P20)
D
P20 (INT5, STOP)
Q
Output latch
Contorl input
Data input (P21PRD)
Osc. enable
Output latch read (P21)
Data output (P21)
D
P21 (XTIN)
Q
Output latch
Data input (P22PRD)
Output latch read (P22)
Data output (P22)
D
P22 (XTOUT)
Q
Output latch
STOP
OUTEN
XTEN
fs
Figure 5-4 Port 2
P2DR
(0002H)
R/W
7
6
5
4
3
2
1
0
P22
XTOUT
P21
XTIN
INT5
P20
(Initial value: **** *111)
STOP
P2PRD
(0009H)
Read only
P22
P21
P20
Note: Port P20 is used as STOP pin. Therefore, when stop mode is started, OUTEN does not affect to P20, and P20 becomes
high-Z mode.
Page 53
5. I/O Ports
5.4 Port P3 (P37 to 30)
TMP86CH12MG
5.4 Port P3 (P37 to 30)
Port P3 is an 8-bit input/output port which can be configured as an input or output in one-bit unit.
Port P3 is also used as an analog input, key-on wakeup input, an external interrupt and TC7 emergency stop input.
Input/output mode is specified by the P3 control register (P3CR1) and P3 input control register (P3CR2).
During reset, the P3CR1 is initialized to "0" the P3CR2 is initialized to "1" and port P3 becomes an input mode.
And the P3DR is initialized to "0".
When used as an output port, the corresponding bit of P3CR1 should be set to "1".
When used as an input port, key-on wakeup input, an external interrupt input and TC7 emergency stop input, the
corresponding bit of P3CR1 should be set to "0" and then, the corresponding bit of P3CR2 should be set to "1".
When used as an analog input, the corresponding bit of P3CR1 should be set to "0" and then, the corresponding bit
of P6CR2 should be set to "0".
When P3CR1 is "1", the content of the corresponding output latch is read by reading P3DR.
Table 5-3 Register Programming for Multi-function Ports
Programmed Value
Function
P3DR
P3CR1
P3CR2
Port input or key-on wakeup input or external input or
TC7 emergency stop input
*
“0”
“1”
Analog input
*
“0”
“0”
Port “0” output
“0”
“1”
*
Port “1” output
“1”
“1”
*
Note: Asterisk (*) indicates “1” or “0” either of which can be selected.
Table 5-4 Values Read from P3DR and Register Programming
Conditions
Values Read from P3DR
P3CR1
P3CR2
“0”
“0”
“0”
“0”
“1”
Terminal input data
“0”
“1”
Output latch contents
“1”
Page 54
TMP86CH12MG
P3CR2i
D
Q
D
Q
D
Q
P3CR2i KPRWV
P3CR1i
P3CR1i KPRWV
%QPVTQNQWVRWV
&CVCKPRWV (P3DRi)
&CVCQWVRWV (P3DRi)
P3i
STOP
OUTTEN
#PCNQIKPRWV
AINDS
SAIN
a) P37,P32 to P30
-G[QPYCMGWR
STOPkEN
P3CR2j
D
Q
D
Q
D
Q
P3CR2j KPRWV
P3CR1j
P3CR1j KPRWV
&CVCKPRWV (P3DRj)
&CVCQWVRWV (P3DRj)
P3j
STOP
OUTTEN
#PCNQIKPRWV
AINDS
SAIN
b) P36 to P33
Note: i = 7 to 0
Figure 5-5 Port 3
Page 55
5. I/O Ports
5.4 Port P3 (P37 to 30)
P3DR
(0003H)
R/W
P3CR1
(0006H)
TMP86CH12MG
7
6
5
4
3
2
1
0
P37
AIN7
P36
AIN6
STOP3
P35
AIN5
STOP2
P34
AIN4
STOP1
P33
AIN3
STOP0
P32
AIN2
P31
AIN1
INT0
P30
AIN0
EMG
7
6
5
4
3
2
1
0
(Initial value: 0000 0000)
P3CR1
P3CR2
(0007H)
(Initial value: 0000 0000)
7
0: Input mode
1: Output mode
I/O control for port P3 (Specified for each bit)
6
5
4
3
2
1
R/W
0
(Initial value: 1111 1111)
P3CR2
P3 port input control (Specified for each bit)
0: Analog input
1: Port input or key-on wakeup input or external interrupt input or
TC7 emergency stop input
R/W
Note 1: The port placed in input mode reads the pin input state. Therefore, when the input and output modes are used together,
the output latch contents for the port in input mode might be changed by executing a bit manipulation instruction.
Note 2: When used as an analog inport, be sure to clear the corresponding bit of P3CR2 to disable the port input.
Note 3: Do not set the output mode (P3CR1 = “1”) for the pin used as an analog input pin.
Note 4: Pins not used for analog input can be used as I/O ports. During AD conversion, output instructions should not be executed
to keep a precision. In addition, a variable signal should not be input to a port adjacent to the analog input during AD conversion.
Page 56
TMP86CH12MG
6. Watchdog Timer (WDT)
The watchdog timer is a fail-safe system to detect rapidly the CPU malfunctions such as endless loops due to spurious noises or the deadlock conditions, and return the CPU to a system recovery routine.
The watchdog timer signal for detecting malfunctions can be programmed only once as “reset request” or “interrupt request”. Upon the reset release, this signal is initialized to “reset request”.
When the watchdog timer is not used to detect malfunctions, it can be used as the timer to provide a periodic interrupt.
Note: Care must be taken in system design since the watchdog timer functions are not be operated completely due to
effect of disturbing noise.
6.1 Watchdog Timer Configuration
Reset release
23
15
Binary counters
Selector
fc/2 or fs/2
fc/221 or fs/213
fc/219 or fs/211
fc/217 or fs/29
Clock
Clear
R
Overflow
1
WDT output
2
S
2
Q
Interrupt request
Internal reset
Q
S R
WDTEN
WDTT
Writing
disable code
Writing
clear code
WDTOUT
Controller
0034H
WDTCR1
0035H
WDTCR2
Watchdog timer control registers
Figure 6-1 Watchdog Timer Configuration
Page 57
Reset
request
INTWDT
interrupt
request
6. Watchdog Timer (WDT)
6.2 Watchdog Timer Control
TMP86CH12MG
6.2 Watchdog Timer Control
The watchdog timer is controlled by the watchdog timer control registers (WDTCR1 and WDTCR2). The watchdog timer is automatically enabled after the reset release.
6.2.1
Malfunction Detection Methods Using the Watchdog Timer
The CPU malfunction is detected, as shown below.
1. Set the detection time, select the output, and clear the binary counter.
2. Clear the binary counter repeatedly within the specified detection time.
If the CPU malfunctions such as endless loops or the deadlock conditions occur for some reason, the watchdog timer output is activated by the binary-counter overflow unless the binary counters are cleared. When
WDTCR1<WDTOUT> is set to “1” at this time, the reset request is generated and then internal hardware is
initialized. When WDTCR1<WDTOUT> is set to “0”, a watchdog timer interrupt (INTWDT) is generated.
The watchdog timer temporarily stops counting in the STOP mode including the warm-up or IDLE/SLEEP
mode, and automatically restarts (continues counting) when the STOP/IDLE/SLEEP mode is inactivated.
Note:The watchdog timer consists of an internal divider and a two-stage binary counter. When the clear code 4EH
is written, only the binary counter is cleared, but not the internal divider. The minimum binary-counter overflow
time, that depends on the timing at which the clear code (4EH) is written to the WDTCR2 register, may be 3/
4 of the time set in WDTCR1<WDTT>. Therefore, write the clear code using a cycle shorter than 3/4 of the
time set to WDTCR1<WDTT>.
Example :Setting the watchdog timer detection time to 221/fc [s], and resetting the CPU malfunction detection
Within 3/4 of WDT
detection time
LD
(WDTCR2), 4EH
: Clears the binary counters.
LD
(WDTCR1), 00001101B
: WDTT ← 10, WDTOUT ← 1
LD
(WDTCR2), 4EH
: Clears the binary counters (always clears immediately before and
after changing WDTT).
(WDTCR2), 4EH
: Clears the binary counters.
(WDTCR2), 4EH
: Clears the binary counters.
:
:
LD
Within 3/4 of WDT
detection time
:
:
LD
Page 58
TMP86CH12MG
Watchdog Timer Control Register 1
WDTCR1
(0034H)
7
WDTEN
6
5
4
3
(ATAS)
(ATOUT)
WDTEN
Watchdog timer enable/disable
2
1
0
WDTT
WDTOUT
(Initial value: **11 1001)
0: Disable (Writing the disable code to WDTCR2 is required.)
1: Enable
NORMAL1/2 mode
WDTT
WDTOUT
Watchdog timer detection time
[s]
Watchdog timer output select
DV7CK = 0
DV7CK = 1
SLOW1/2
mode
00
225/fc
217/fs
217/fs
01
223/fc
215/fs
215fs
10
221fc
213/fs
213fs
11
219/fc
211/fs
211/fs
0: Interrupt request
1: Reset request
Write
only
Write
only
Write
only
Note 1: After clearing WDTOUT to “0”, the program cannot set it to “1”.
Note 2: fc: High-frequency clock [Hz], fs: Low-frequency clock [Hz], *: Don’t care
Note 3: WDTCR1 is a write-only register and must not be used with any of read-modify-write instructions. If WDTCR1 is read, a
don’t care is read.
Note 4: To activate the STOP mode, disable the watchdog timer or clear the counter immediately before entering the STOP mode.
After clearing the counter, clear the counter again immediately after the STOP mode is inactivated.
Note 5: To clear WDTEN, set the register in accordance with the procedures shown in “1.2.3 Watchdog Timer Disable”.
Watchdog Timer Control Register 2
WDTCR2
(0035H)
7
6
5
4
3
2
1
0
(Initial value: **** ****)
WDTCR2
Write
Watchdog timer control code
4EH: Clear the watchdog timer binary counter (Clear code)
B1H: Disable the watchdog timer (Disable code)
D2H: Enable assigning address trap area
Others: Invalid
Write
only
Note 1: The disable code is valid only when WDTCR1<WDTEN> = 0.
Note 2: *: Don’t care
Note 3: The binary counter of the watchdog timer must not be cleared by the interrupt task.
Note 4: Write the clear code 4EH using a cycle shorter than 3/4 of the time set in WDTCR1<WDTT>.
6.2.2
Watchdog Timer Enable
Setting WDTCR1<WDTEN> to “1” enables the watchdog timer. Since WDTCR1<WDTEN> is initialized
to “1” during reset, the watchdog timer is enabled automatically after the reset release.
Page 59
6. Watchdog Timer (WDT)
6.2 Watchdog Timer Control
6.2.3
TMP86CH12MG
Watchdog Timer Disable
To disable the watchdog timer, set the register in accordance with the following procedures. Setting the register in other procedures causes a malfunction of the microcontroller.
1. Set the interrupt master flag (IMF) to “0”.
2. Set WDTCR2 to the clear code (4EH).
3. Set WDTCR1<WDTEN> to “0”.
4. Set WDTCR2 to the disable code (B1H).
Note:While the watchdog timer is disabled, the binary counters of the watchdog timer are cleared.
Example :Disabling the watchdog timer
: IMF ← 0
DI
LD
(WDTCR2), 04EH
: Clears the binary coutner
LDW
(WDTCR1), 0B101H
: WDTEN ← 0, WDTCR2 ← Disable code
Table 6-1 Watchdog Timer Detection Time (Example: fc = 16.0 MHz, fs = 32.768 kHz)
Watchdog Timer Detection Time[s]
WDTT
6.2.4
NORMAL1/2 mode
DV7CK = 0
DV7CK = 1
SLOW
mode
00
2.097
4
4
01
524.288 m
1
1
10
131.072 m
250 m
250 m
11
32.768 m
62.5 m
62.5 m
Watchdog Timer Interrupt (INTWDT)
When WDTCR1<WDTOUT> is cleared to “0”, a watchdog timer interrupt request (INTWDT) is generated
by the binary-counter overflow.
A watchdog timer interrupt is the non-maskable interrupt which can be accepted regardless of the interrupt
master flag (IMF).
When a watchdog timer interrupt is generated while the other interrupt including a watchdog timer interrupt
is already accepted, the new watchdog timer interrupt is processed immediately and the previous interrupt is
held pending. Therefore, if watchdog timer interrupts are generated continuously without execution of the
RETN instruction, too many levels of nesting may cause a malfunction of the microcontroller.
To generate a watchdog timer interrupt, set the stack pointer before setting WDTCR1<WDTOUT>.
Example :Setting watchdog timer interrupt
LD
SP, 023FH
: Sets the stack pointer
LD
(WDTCR1), 00001000B
: WDTOUT ← 0
Page 60
TMP86CH12MG
6.2.5
Watchdog Timer Reset
When a binary-counter overflow occurs while WDTCR1<WDTOUT> is set to “1”, a watchdog timer reset
request is generated. When a watchdog timer reset request is generated, the internal hardware is reset. The reset
time is maximum 24/fc [s] (1.5 µs @ fc = 16.0 MHz).
Note:When a watchdog timer reset is generated in the SLOW1 mode, the reset time is maximum 24/fc (high-frequency clock) since the high-frequency clock oscillator is restarted. However, when crystals have inaccuracies upon start of the high-frequency clock oscillator, the reset time should be considered as an approximate
value because it has slight errors.
219/fc [s]
217/fc
Clock
Binary counter
(WDTT=11)
1
2
3
0
1
2
3
0
Overflow
INTWDT interrupt request
(WDTCR1<WDTOUT>= "0")
Internal reset
A reset occurs
(WDTCR1<WDTOUT>= "1")
Write 4EH to WDTCR2
Figure 6-2 Watchdog Timer Interrupt
Page 61
6. Watchdog Timer (WDT)
6.3 Address Trap
TMP86CH12MG
6.3 Address Trap
The Watchdog Timer Control Register 1 and 2 share the addresses with the control registers to generate address
traps.
Watchdog Timer Control Register 1
7
WDTCR1
(0034H)
6
ATAS
ATOUT
5
4
3
ATAS
ATOUT
(WDTEN)
2
1
(WDTT)
0
(WDTOUT)
(Initial value: **11 1001)
Select address trap generation in
the internal RAM area
0: Generate no address trap
1: Generate address traps (After setting ATAS to “1”, writing the control code
D2H to WDTCR2 is reguired)
Select opertion at address trap
0: Interrupt request
1: Reset request
Write
only
Watchdog Timer Control Register 2
WDTCR2
(0035H)
7
5
4
3
2
1
0
(Initial value: **** ****)
WDTCR2
6.3.1
6
Write
Watchdog timer control code
and address trap area control
code
D2H: Enable address trap area selection (ATRAP control code)
4EH: Clear the watchdog timer binary counter (WDT clear code)
B1H: Disable the watchdog timer (WDT disable code)
Others: Invalid
Write
only
Selection of Address Trap in Internal RAM (ATAS)
WDTCR1<ATAS> specifies whether or not to generate address traps in the internal RAM area. To execute
an instruction in the internal RAM area, clear WDTCR1<ATAS> to “0”. To enable the WDTCR1<ATAS> setting, set WDTCR1<ATAS> and then write D2H to WDTCR2.
Executing an instruction in the SFR or DBR area generates an address trap unconditionally regardless of the
setting in WDTCR1<ATAS>.
6.3.2
Selection of Operation at Address Trap (ATOUT)
When an address trap is generated, either the interrupt request or the reset request can be selected by
WDTCR1<ATOUT>.
6.3.3
Address Trap Interrupt (INTATRAP)
While WDTCR1<ATOUT> is “0”, if the CPU should start looping for some cause such as noise and an
attempt be made to fetch an instruction from the on-chip RAM (while WDTCR1<ATAS> is “1”), DBR or the
SFR area, address trap interrupt (INTATRAP) will be generated.
An address trap interrupt is a non-maskable interrupt which can be accepted regardless of the interrupt master flag (IMF).
When an address trap interrupt is generated while the other interrupt including a watchdog timer interrupt is
already accepted, the new address trap is processed immediately and the previous interrupt is held pending.
Therefore, if address trap interrupts are generated continuously without execution of the RETN instruction, too
many levels of nesting may cause a malfunction of the microcontroller.
To generate address trap interrupts, set the stack pointer beforehand.
Page 62
TMP86CH12MG
6.3.4
Address Trap Reset
While WDTCR1<ATOUT> is “1”, if the CPU should start looping for some cause such as noise and an
attempt be made to fetch an instruction from the on-chip RAM (while WDTCR1<ATAS> is “1”), DBR or the
SFR area, address trap reset will be generated.
When an address trap reset request is generated, the internal hardware is reset. The reset time is maximum
24/fc [s] (1.5 µs @ fc = 16.0 MHz).
Note:When an address trap reset is generated in the SLOW1 mode, the reset time is maximum 24/fc (high-frequency clock) since the high-frequency clock oscillator is restarted. However, when crystals have inaccuracies upon start of the high-frequency clock oscillator, the reset time should be considered as an approximate
value because it has slight errors.
Page 63
6. Watchdog Timer (WDT)
6.3 Address Trap
TMP86CH12MG
Page 64
TMP86CH12MG
7. Time Base Timer (TBT)
The time base timer generates time base for key scanning, dynamic displaying, etc. It also provides a time base
timer interrupt (INTTBT).
7.1 Time Base Timer
7.1.1
Configuration
MPX
fc/223 or fs/215
fc/221 or fs/213
fc/216 or fs/28
fc/214 or fs/26
fc/213 or fs/25
fc/212 or fs/24
fc/211 or fs/23
fc/29 or fs/2
Source clock
IDLE0, SLEEP0
release request
Falling edge
detector
INTTBT
interrupt request
3
TBTCK
TBTEN
TBTCR
Time base timer control register
Figure 7-1 Time Base Timer configuration
7.1.2
Control
Time Base Timer is controled by Time Base Timer control register (TBTCR).
Time Base Timer Control Register
7
TBTCR
(0036H)
6
(DVOEN)
TBTEN
5
(DVOCK)
Time Base Timer
enable / disable
4
3
(DV7CK)
TBTEN
2
1
0
TBTCK
(Initial Value: 0000 0000)
0: Disable
1: Enable
NORMAL1/2, IDLE1/2 Mode
TBTCK
Time Base Timer interrupt
Frequency select : [Hz]
DV7CK = 0
DV7CK = 1
SLOW1/2
SLEEP1/2
Mode
000
fc/223
fs/215
fs/215
001
fc/221
fs/213
fs/213
010
fc/216
fs/28
–
011
fc/2
14
6
–
100
fc/213
fs/25
–
101
fc/2
12
4
–
110
fc/211
fs/23
–
111
9
fs/2
–
fc/2
Note 1: fc; High-frequency clock [Hz], fs; Low-frequency clock [Hz], *; Don't care
Page 65
fs/2
fs/2
R/W
7. Time Base Timer (TBT)
7.1 Time Base Timer
TMP86CH12MG
Note 2: The interrupt frequency (TBTCK) must be selected with the time base timer disabled (TBTEN="0"). (The interrupt frequency must not be changed with the disable from the enable state.) Both frequency selection and enabling can be performed simultaneously.
Example :Set the time base timer frequency to fc/216 [Hz] and enable an INTTBT interrupt.
LD
(TBTCR) , 00000010B
; TBTCK ← 010
LD
(TBTCR) , 00001010B
; TBTEN ← 1
; IMF ← 0
DI
SET
(EIRH) . 1
Table 7-1 Time Base Timer Interrupt Frequency ( Example : fc = 16.0 MHz, fs = 32.768 kHz )
Time Base Timer Interrupt Frequency [Hz]
TBTCK
7.1.3
NORMAL1/2, IDLE1/2 Mode
NORMAL1/2, IDLE1/2 Mode
SLOW1/2, SLEEP1/2 Mode
DV7CK = 0
DV7CK = 1
000
1.91
1
1
001
7.63
4
4
010
244.14
128
–
011
976.56
512
–
100
1953.13
1024
–
101
3906.25
2048
–
110
7812.5
4096
–
111
31250
16384
–
Function
An INTTBT ( Time Base Timer Interrupt ) is generated on the first falling edge of source clock ( The divider
output of the timing generato which is selected by TBTCK. ) after time base timer has been enabled.
The divider is not cleared by the program; therefore, only the first interrupt may be generated ahead of the set
interrupt period ( Figure 7-2 ).
Source clock
TBTCR<TBTEN>
INTTBT
Interrupt period
Enable TBT
Figure 7-2 Time Base Timer Interrupt
Page 66
TMP86CH12MG
7.2 Divider Output (DVO)
Approximately 50% duty pulse can be output using the divider output circuit, which is useful for piezoelectric
buzzer drive. Divider output is from DVO pin.
7.2.1
Configuration
Output latch
D
Data output
Q
DVO pin
MPX
A
B
C Y
D
S
2
fc/213 or fs/25
fc/212 or fs/24
fc/211 or fs/23
fc/210 or fs/22
Port output latch
TBTCR<DVOEN>
DVOCK
DVOEN
TBTCR
DVO pin output
Divider output control register
(a) configuration
(b) Timing chart
Figure 7-3 Divider Output
7.2.2
Control
The Divider Output is controlled by the Time Base Timer Control Register.
Time Base Timer Control Register
7
TBTCR
(0036H)
DVOEN
DVOEN
6
5
DVOCK
4
3
(DV7CK)
(TBTEN)
Divider output
enable / disable
2
1
0
(TBTCK)
(Initial value: 0000 0000)
0: Disable
1: Enable
R/W
DV7CK = 0
DV7CK = 1
SLOW1/2
SLEEP1/2
Mode
00
fc/213
fs/25
fs/25
01
fc/212
fs/24
fs/24
10
fc/211
fs/23
fs/23
11
fc/210
fs/22
fs/22
NORMAL1/2, IDLE1/2 Mode
DVOCK
Divider Output (DVO)
frequency selection: [Hz]
R/W
Note: Selection of divider output frequency (DVOCK) must be made while divider output is disabled (DVOEN="0"). Also, in other
words, when changing the state of the divider output frequency from enabled (DVOEN="1") to disable(DVOEN="0"), do not
change the setting of the divider output frequency.
Page 67
7. Time Base Timer (TBT)
7.2 Divider Output (DVO)
TMP86CH12MG
Example :1.95 kHz pulse output (fc = 16.0 MHz)
LD
(TBTCR) , 00000000B
; DVOCK ← "00"
LD
(TBTCR) , 10000000B
; DVOEN ← "1"
Table 7-2 Divider Output Frequency ( Example : fc = 16.0 MHz, fs = 32.768 kHz )
Divider Output Frequency [Hz]
DVOCK
NORMAL1/2, IDLE1/2 Mode
DV7CK = 0
DV7CK = 1
SLOW1/2, SLEEP1/2
Mode
00
1.953 k
1.024 k
1.024 k
01
3.906 k
2.048 k
2.048 k
10
7.813 k
4.096 k
4.096 k
11
15.625 k
8.192 k
8.192 k
Page 68
TMP86CH12MG
8. Real-Time Clock
The TMP86CH12MG include a real time counter (RTC). A low-frequency clock can be used to provide a periodic
interrupt (0.0625[s],0.125[s],0.25[s],0.50[s]) at a programmed interval, implement the clock function. The RTC can
be used in the mode in which the low-frequency oscillator is active (except for the SLEEP0 mode).
8.1 Configuration
RTCCR
Interrupt request
INTRTC
Selector
RTCSEL
RTCRUN
211/fs 212/fs 213/fs 214/fs
fs
(32.768 kHz)
Binary counter
Figure 8-1 Configuration of the RTC
8.2 Control of the RTC
The RTC is controlled by the RTC control register (RTCCR).
RTC Control Register
RTCCR
(001BH)
7
6
5
4
3
2
1
RTCSEL
RTCSEL
RTCRUN
0
RTCRUN
Interrupt generation period
(fs = 32.768 kHz)
00: 0.50 [s]
01: 0.25 [s]
10: 0.125 [s]
11: 0.0625 [s]
RTC control
0: Stops and clears the binary counter.
1: Starts counting
(Initial value: **** *000)
R/W
Note 1: Program the RTCCR during low-frequency oscillation (when SYSCR2<XTEN> = “1”). For selecting an interrupt generation period, program the RTCSEL when the timer is inactive (RTCRUN = “0”). During the timer operation, do not change
the RTCSEL programming at the same moment the timer stops.
Note 2: The timer automatically stops, and this register is initialized (the timer's binary counter is also initialized) if one of the following operations is performed while the timer is active:
1. Stopping the low-frequency oscillation (with SYSCR2<XTEN> = “0”)
2. When the TMP86CH12MG are put in STOP or SLEEP0 mode
Therefore, before activating the timer after releasing from STOP or SLEEP0 mode, reprogram the registers again.
Note 3: If a read instruction for RTCCR is executed, undefined value is set to bits 7 to 3.
Note 4: If break processing is performed on the debugger for the development tool during the timer operation, the timer stops
counting (contents of the RTCCR isn't altered). When the break is cancelled, processing is restarted from the point at
which it was suspended.
Page 69
8. Real-Time Clock
8.3 Function
TMP86CH12MG
8.3 Function
The RTC counts up on the internal low-frequency clock. When RTCCR<RTCRUN> is set to “1”, the binary
counter starts counting up. Each time the end of the period specified with RTCCR<RTCSEL> is detected, an
INTRTC interrupt is generated, and the binary counter is cleared. The timer continues counting up even after the
binary counter is cleared.
Page 70
TMP86CH12MG
9. 10-Bit Timer/Counter (TC7)
9.1 Configuration
CSIDIS
TC7CR3
TC7ST
EMGF
CSTC
A
B
C
D
fc
fc/2
fc/22
fc/23
STM
Y
INTTC7T interrupt request
10-bit up counter
Start/
clear
S
TC7CK
PPG2INI
PPG1INI
CNTBF
TGRAM
TC7CR1
Noise
canceller
TC7 pin
TC7CAPA
TRGSEL
NCRSEL
TC7CAPB
Capture
control
Edge
detection
INTTC7P interrupt request
CSIDIS
PPG1
Comparator
Compare
register A
Compare
register B
Compare
register C
PPG output control
Compare
register D
PPG2
TC7OUT PPG1OE/ PPG1INI/
PPG2OE PPG2INI
Compare
register E
Transfer control
TC7DRA
TC7DRB
TC7DRC
TC7DRD
TC7DRE
Emergency stop
EMGF
Emergency output
EMG pin
INTEMG interrupt request
stop control
EMGIE
EMGR
CSTC
PPG2OE
PPG1OE
TC7CR2
TC7OUT
Figure 9-1 10-Bit Timer/Counter 7
9.2 Control
Timer/counter 7 is controlled by timer/counter control register 1 (TC7CR1), timer/counter control register 2
(TC7CR2), timer/counter control register 3 (TC7CR3), 10-bit dead time 1 setup register (TC7DRA), pulse width 1
setup register (TC7DRB), period setup register (TC7DRC), dead time 2 setup register (TC7DRD), pulse width 2
setup register (TC7DRE), and two capture value registers (TC7CAPA and TC7CAPB).
Timer/Counter 7 Control Register 1
TC7CR1
(0029H)
7
6
5
4
TRGAM
TRGSEL
PPG2INI
PPG1INI
3
2
NCRSEL
Page 71
1
0
TC7CK
(Initial value: 0000 0000)
9. 10-Bit Timer/Counter (TC7)
9.2 Control
TMP86CH12MG
TC7CK
Select a source clock
(Supplied to the up counter).
00: fc
01: fc/2
[Hz]
[Hz]
10 fc/22
[Hz]
11: fc/23 [Hz]
NCRSEL
Select the duration of noise elimination for
TC7 input
(after passing through the flip-flop).
00: Eliminate pulses shorter than 16/fc [s] as noise.
01: Eliminate pulses shorter than 8/fc [s] as noise.
10: Eliminate pulses shorter than 4/fc [s] as noise.
11: Do not eliminate noise. (Note)
PPG1INI
Specify the initial
value of PPG1 output.
0: Low (Positive logic)
1: High (Negative logic)
Select positive or
negative logic.
PPG2INI
Specify the initial
value of PPG2 output.
TRGSEL
Select a trigger start edge.
R/W
0: Low (Positive logic)
1: High (Negative logic)
0: Start on trigger falling edge.
1: Start on trigger rising edge.
TRGAM
0: Always accept trigger edges.
1: Do not accept trigger edges during active output.
Trigger edge acceptance mode
Note: Due to the circuit configuration, a pulse shorter than 1/fc may be eliminated as noise or accepted as a trigger.
Timer/Counter 7 Control Register 2
TC7CR2
(002AH)
7
6
5
4
EMGR
EMGIE
PPG2OE
PPG1OE
3
2
1
CSTC
0
TC7OUT
Select an output waveform mode.
00: PPG1/PPG2 independent output
01: –
10: Output with variable duty ratio
11: Output with 50% duty ratio
CSTC
Select a count start mode.
00: Command start and capture mode
01: Command start and trigger start mode.
10: Trigger start mode
11: -
PPG1OE
Enable/disable PPG1 output.
0: Disable
1: Enable
PPG2OE
Enable/disable PPG2 output.
0: Disable
1: Enable
EMGIE
Enable/disable input on the EMG pin.
0: Disable input.
1: Enable input.
Cancel the emergency output stop state.
0: 1: Cancel the emergency output stop state.
(Upon canceling the state,
this bit is automatically cleared to 0.)
TC7OUT
EMGR
(Initial value: 0000 0000)
R/W
Timer/Counter 7 Control Register 3
TC7CR3
(002BH)
7
6
5
4
3
EMGF
CNTBF
CSIDIS
Page 72
2
1
STM
0
TC7ST
(Initial value: **00 0000)
TMP86CH12MG
TC7ST
0: Stop
1: Start
Start/stop the timer.
TC7ST = 0
STM
Select the state when stopped.
Select continuous or one-time output.
TC7ST = 1
00: Immediately stop and clear the counter with the
output initialized.
Continuous output
01: Immediately stop and clear the counter with the
output maintained.
Continuous output
10: Stop the counter after completing output in the
current period.
One-time output
11: -
–
CSIDIS
Disable the first interrupt at upon a command start.
0: Allow a periodic interrupt (INTTC7P) to occur in the first period upon a
command start.
1: Do not allow a periodic interrupt (INTTC7P) to occur in the first period
upon a command start.
CNTBF
Counting status flag
0: Counting stopped
1: Counting in progress
Emergency output stop flag
0: Operating normally
1: Output stopped in emergency
EMGF
R/W
Read
only
Note 1: The TC7CR1 and TC7CR2 registers should not be rewritten after a timer start (when TC7ST, bit0 of the TC7CR3, is set to
1).
Note 2: Before attempting to modify the TC7CR1 or TC7CR2, clear TC7ST and then check that CNTBF = 0 to determine that the
timer is stopped.
Note 3: The TC7ST bit only causes the timer to start or stop; it does not indicate the current operating state of the counter. Its
value does not change automatically when counting starts or stops
Note 4: In command start and capture mode or command start and trigger start mode, writing 1 to TC7ST causes the timer to
restart immediately. It means that rewriting any bit other than TC7ST in the TC7CR3 after a command start causes the
rewriting of TC7ST, resulting in the timer being restarted (PPG output is started from the initial state). When TC7ST is set
to 1, rewriting the TC7CR3 (Using a bit manipulation or LD instruction) clears the counter and restarts the timer.
Note 5: TC7CR2<EMGR> is always read as 0 even after 1 is written.
Note 6: Data registers are not updated by merely modifying the output mode with TC7CR2<TC7OUT>. After modifying the output
mode, reconfigure data registers TC7DRA to TC7DRE. Ensure that the data registers are written in an appropriate order
because they are not enabled until the upper byte of the TC7DRC is written.
Dead Time 1 Setup Register
15
14
13
12
11
10
9
8
7
6
5
TC7DRAH
(0009H)
TC7DRA
4
3
2
1
0
2
1
0
2
1
0
TC7DRAL
(0008H)
(0009H, 0008H) Read/Write (Initial value: **** **00 0000 0000)
Pulse Width 1 Setup Register
15
14
13
12
11
10
9
8
7
6
5
TC7DRBH
(000BH)
TC7DRB
4
3
TC7DRBL
(000AH)
(000BH, 000AH) Read/Write (Initial value: **** **00 0000 0000)
Period Setup Register
15
14
13
12
11
10
9
8
TC7DRCH
(000DH)
TC7DRC
(000DH, 000CH) Read/Write (Initial value: **** **00 0000 0000)
Page 73
7
6
5
4
3
TC7DRCL
(000CH)
9. 10-Bit Timer/Counter (TC7)
9.2 Control
TMP86CH12MG
Dead Time 2 Setup Register
15
14
13
12
11
10
9
8
7
6
5
TC7DRDH
(0FB1H)
TC7DRD
4
3
2
1
0
2
1
0
TC7DRDL
(0FB0H)
(0FB1H, 0FB0H) Read/Write (Initial value: **** **00 0000 0000)
Pulse Width 2 Setup Register
15
14
13
12
11
10
9
8
7
6
5
TC7DREH
(0FB3H)
TC7DRE
4
3
TC7DREL
(0FB2H)
(0FB3H, 0FB2H) Read/Write (Initial value: **** **00 0000 0000)
Note 1: Data registers TC7DRA to TC7DRE have double-stage configuration, consisting of a data register that stores data written
by an instruction and a compare register to be compared with the counter.
Note 2: When writing data to data registers TC7DRA to TC7DRE, first write the lower byte and then the upper byte.
Note 3: Unused bits (Bits 10 to 15) in the upper bytes of data registers TC7DRA to TC7DRE are not assigned specific register
functions. These bits are always read as 0 even when a 1 is written.
Note 4: Values read from data registers TC7DRA to TC7DRE may differ from the actual PPG output waveforms due to their double-stage configuration.
Note 5: Data registers are not updated by merely modifying the output mode with TC7CR2<TC7OUT>. After modifying the output
mode, reconfigure data registers TC7DRA to TC7DRE. Ensure that the data registers are written in an appropriate order
because they are not enabled until the upper byte of the TC7DRC is written.
Rising-edge Capture Value Register
15
14
13
12
11
10
9
8
7
6
5
TC7CAPAH
(0FB5H)
TC7CAPA
4
3
2
1
0
2
1
0
TC7CAPAL
(0FB4H)
(0FB5H, 0FB4H) Read only (Initial value: 0000 00** **** ****)
Falling-edge Capture Value Register
15
14
13
12
11
10
TC7CAPB
9
8
7
TC7CAPBH
(0FB7H)
6
5
4
3
TC7CAPBL
(0FB6H)
(0FB7H, 0FB6H) Read only (Initial value: 0000 00** **** ****)
Note 1: Capture registers (TC7CAPA and TC7CAPB) must be read in the following order: Lower byte of the TC7CAPA, upper byte
of the TC7CAPA, lower byte of the TC7CAPB, upper byte of the TC7CAPB.
Note 2: The next captured data is not updated by reading the TC7CAPA only. The TC7CAPB must also be read.
Note 3: It is possible to read the TC7CAPB only. Read the lower byte first.
Note 4: If a capture edge is not detected within a period, the previous capture value is maintained in the next period.
Note 5: If more than one capture edge is detected within a period, the capture value for the edge detected last is valid in the next
period.
Note 6: Bits 10 to 15 of the TC7CAPA and TC7CAPB are always read as 0.
Page 74
TMP86CH12MG
9.3 Configuring Control and Data Registers
Configure control and data registers in the following order:
1. Configure mode settings: TC7CR1, TC7CR2
2. Configure data registers (Dead time, pulse width):
TC7DRA, TC7DRB, TC7DRD, TC7DRE (only those required for selected mode)
3. Configure data registers (Period): TC7DRC
4. Configure timer start/stop:TC7CR3
• Data registers have double-stage configuration, consisting of a data register that stores data written by
an instruction and a compare register to be compared with the counter.
• Data stored in a data register is processed according to the output mode specified in the TC7OUT,
transferred to the compare register, and then used for comparison with the up counter.
• Data registers required for the specified output mode are used for data register processing and transfer
to the compare register. Ensure that the output mode is specified in the TC7OUT (Bits 0 and 1 of the
TC7CR2) before configuring data registers.
• Writing data to the upper byte of the TC7DRC causes a data transfer request to be issued for data in
data registers TC7DRA to TC7DRE. If a counter match or clear occurs while that request is valid, the
data is transferred to the compare register and becomes valid for comparison.
• If a data register is written more than once within a period, the data in the data register that was set
when the upper byte of the TC7DRC was written is valid as data for the next period. The data in the
data register written last in the first period will be valid for the period that follows the next period.
Execute write
instruction.
Execute write
instruction.
A1
B1
C1
TC7DRA
TC7DRB
TC7DRC
A2
B2
C2
Period (2)
Period (3)
Period (4)
Previous data is
maintained if data is not
rewritten within the period.
Execute more than one
data write instruction.
A1
B1
C1
A2
Data valid
in each
period
A1
B1
C1
TC7DRA
TC7DRB
TC7DRC
A3
B3
C3
Period (1)
Valid in next
period
Execute write
instruction.
Execute write
instruction.
C2
C3
B2
C4
Execute write instruction.
A3
A4
A5
C5
C6
C7
A2
B1
C2
Period (1)
If data is rewritten more
than once within a
period, the data written
first is valid in the next
period.
No data write
Execute write instruction.
A6
B3
C8
A3
B2
C5
Period (2)
A7
B4
C9
A5
B2
C7
Period (3)
Period (4)
If data is rewritten more than
once within a period, the data
written last is valid in the
period following the next
period.
Figure 9-2 Example Configuration of Control/data Registers (1)
Page 75
A6
B3
C8
Period (5)
9. 10-Bit Timer/Counter (TC7)
9.4 Features
TMP86CH12MG
More than one data write
TC7DRA
TC7DRB
TC7DRC
A1
B1
C1
Data valid
in each
period
a1
b1
c1
A2
B2
C2
No data write
More than one data write
C3
A1
B1
C1
A1
B1
C1
A3
B3
C3
A3
B3
Period (1)
Period (2)
A2
B2
C2
A3
B3
C3
A4
B4
C3
A1
B1
C1
Period (3)
Period (4)
A3
B3
C3
Period (5)
A4
B4
C3
Period (6)
If TC7DRC is written in
the next period
Figure 9-3 Example Configuration of Control/data Registers (2)
9.4 Features
9.4.1
Programmable pulse generator output (PPG output)
The PPG1 and PPG2 pins provide PPG outputs. The output waveform mode for PPG outputs is specified
with TC7CR2<TC7OUT> and their waveforms are controlled by comparing the contents of the 10-bit up
counter with the data set in data registers (TC7DRA to TC7DRE). Three output waveform modes are available:
50% duty mode, variable duty mode, and PPG1/PPG2 independent mode.
9.4.1.1
50% duty mode
(1)
Description
With a period specified in the TC7DRC, the PPG1 and PPG2 pins provide waveforms having a
pulse width (Active duration) that equals a half the period.
The PPG1 output is active at the beginning of a period and becomes inactive at half the period. The
PPG2 output is inactive at the beginning of a period, becomes active at half the period, and remains
active until the end of the period.
If a dead time is specified in the TC7DRA, the pulse width (Active duration) is shortened by the
dead time.
(2)
Register settings
TC7OUT = “11”, TC7DRA = “dead time”, TC7DRC = “period”
(3)
Valid range for data register values
(a) Period:
002H ≤ TC7DRC ≤ 400H (Writing 400H to TC7DRC results in 000H being read from it.)
Page 76
TMP86CH12MG
When the value set in the TC7DRC is an odd number, the PPG2 pulse width is one count
longer than the PPG1 pulse width.
(b) Dead time TC7DRA:
000H ≤ TC7DRA < TC7DRC/2
To specify no dead time, set the TC7DRA to 000H.
Source clock
S, 0
Counter
1
M
S/2
S/2+1
S, 0
S/2+M
1
2
Dead time
M
M'
Period
S
S
PPG1 output
M: Dead time
3
Active duration
M: Dead time
PPG2 output
Active duration
S: Period
INTTC7T
INTTC7P
Dead time
(TC7DRA)
Dead time
(TC7DRA)
Pulse width (TC7DRC/2)
Pulse width (TC7DRC/2)
Period (TC7DRC)
Figure 9-4 Example operation in 50% duty mode:
Command and capture start, positive logic, continuous output
9.4.1.2
Variable duty mode
(1)
Description
With a period specified in the TC7DRC and a pulse width in the TC7DRB, the PPG1 pin provides
a waveform having the specified pulse width while the PPG2 pin provides a waveform having a
pulse width that equals (TC7DRC – TC7DRB).
The PPG1 output is active at the beginning of a period, remains active during the pulse width specified in the TC7DRB, after which it is inactive until the end of the period. The PPG2 output is inactive at the beginning of a period, remains inactive during the pulse width specified in the TC7DRB,
after which it is active until the end of the period, that is, during the pulse width of (TC7DRC –
TC7DRB).
If a dead time is specified in the TC7DRA, the pulse width (Active duration) is shortened by the
dead time.
(2)
Register settings
TC7OUT = “10”, TC7DRA = “dead time”, TC7DRB = “pulse width”, TC7DRC = “period”
Page 77
9. 10-Bit Timer/Counter (TC7)
9.4 Features
TMP86CH12MG
(3)
Valid range for data register values
(a) Period:
002H ≤ TC7DRB + TC7DRA < TC7DRC ≤ 400H
(Writing 400H to TC7DRC results in 000H being read from it.)
(b) Pulse width:
001H ≤ TC7DRB < TC7DRC
(c) Dead time:
000H ≤ TC7DRA < TC7DRB, 000H ≤ TC7DRA < (TC7DRC – TC7DRB)
(To specify no dead time, set the TC7DRA to 000H.)
Source clock
S, 0
Counter
1
M
N N+1
S, 0
N+M
1
2
Dead time
M
M'
Pulse width
N
N'
Period
S
S
PPG1 output
3
M: Dead time
Active duration
N: Pulse width
PPG2 output
M: Dead time
Active duration
S: Period
INTTC7T
INTTC7P
Dead time
(TC7DRA)
Dead time
(TC7DRA)
Pulse width (TC7DRC − TC7DRB)
Pulse width (TC7DRB)
Period (TC7DRC)
Figure 9-5 Example Operation in Variable Duty Mode:
Command and Capture Start, Positive Logic, Continuous Output
9.4.1.3
PPG1/PPG2 independent mode
(1)
Description
For the PPG1 output, specify the dead time in the TC7DRA and pulse width in the TC7DRB. For
the PPG2 output, specify the dead time in the TC7DRD and pulse width in the TC7DRE. With a
common period specified in the TC7DRC, the PPG1 and PPG2 pins provide waveforms having the
specified pulse widths.
Page 78
TMP86CH12MG
The PPG1 output is active at the beginning of a period, remains active during the pulse width specified in the TC7DRB, after which it is inactive until the end of the period.
The PPG2 output is active at the beginning of a period, remains active during the pulse width specified in the TC7DRE, after which it is inactive until the end of the period.
If a dead time is specified in the TC7DRA for the PPG1 output or in the TC7DRD for the PPG2
output, the pulse width (Active duration) is shortened by the dead time.
(2)
Register settings
TC7OUT = “00”, TC7DRC = “period”
TC7DRA = “PPG1 dead time”, TC7DRB = “PPG1 pulse width”
TC7DRD = “PPG2 dead time”, TC7DRE = “PPG2 pulse width”
(3)
Valid range for data register values
(a) Period:
002H ≤ TC7DRC ≤ 400H
(Writing 400H to TC7DRC results in 000H being read from it.)
(b) Pulse width:
001H ≤ TC7DRB ≤ 400H
(Writing 400H to TC7DRB results in 000H being read from it.)
001H ≤ TC7DRE ≤ 400H
(Writing 400H to TC7DRE results in 000H being read from it.)
(c) Dead time:
000H ≤ TC7DRA ≤ 3FFH, where TC7DRA < TC7DRB ≤ TC7DRC
000H ≤ TC7DRD ≤ 3FFH, where TC7DRD < TC7DRE ≤ TC7DRC
(To specify no dead time, write 000H.)
• Settings for a duty ratio of 0%
002H ≤ TC7DRC ≤ TC7DRA ≤ 3FFH (PPG1 output)
002H ≤ TC7DRC ≤ TC7DRD ≤ 3FFH (PPG2 output)
• Settings for a duty ratio greater than 0%, up to 100%
000H ≤ TC7DRA < TC7DRB ≤ TC7DRC ≤ 400H (PPG1 output)
000H ≤ TC7DRD < TC7DRE ≤ TC7DRC ≤ 400H (PPG2 output)
Period
Period
0% duty
100% duty
Page 79
9. 10-Bit Timer/Counter (TC7)
9.4 Features
TMP86CH12MG
Source clock
0
Counter
1
M
N
T
U
S, 0
1
2
Dead time
M
M'
Pulse width
N
N'
Period
S
S
Dead time
T
T'
Pulse width
U
U'
PPG1 output
M: Dead time
3
Active duration
N: Pulse width
PPG2 output
T: Dead time
Active duration
U: Pulse width
INTTC7T
S: Period
INTTC7P
PPG1 dead time
(TC7DRA)
PPG1 pulse width (TC7DRB)
PPG2 dead time (TC7DRD)
PPG2 pulse width (TC7DRE)
Period (TC7DRC)
Figure 9-6 Example Operation in PPG1/PPG2 Independent Mode:
Command and Capture Start, Positive Logic, Continuous Output
9.4.2
Starting a count
A count can be started by using a command or TC7 pin input.
9.4.2.1
Command start and capture mode
(1)
Description
Writing a 1 to TC7ST causes the current count to be cleared and the counter to start counting. Once
the count has reached a specified period, the counter is cleared. The counter subsequently restarts
counting if STM specifies continuous mode; it stops counting if STM specifies one-time mode.
Writing a 1 to TC7ST before the count reaches a period causes the counter to be cleared, after
which it operates as specified with STM.
The count values at the rising and falling edges on the TC7 pin can be stored in capture registers
(Details for the capture are given in a separate section).
Page 80
TMP86CH12MG
(2)
Register settings
CSTC = “00”: Command start and capture mode
STM: Continuous/one-time output
TC7ST = “1”: Starts counting
PPG1
Count start
(Command)
Count cleared
Start
Count cleared
Start
Count cleared
Restart
TC7ST = 1
PPG output with a
period specified
with TC7DRC
PPG output with a
period specified
with TC7DRC
PPG output with a
period specified
with TC7DRC
Figure 9-7 Example Operation in Command Start and Capture Mode
9.4.2.2
Command start and trigger start mode
(1)
Description
Writing a 1 to TC7ST causes the current count to be cleared and the counter to start counting. The
operation is the same as that in command start and capture mode if there is no trigger input on the
TC7 pin. If an edge specified with the start edge selection field (TRGSEL) appears on the TC7 pin,
however, the timer starts counting. The counter is cleared and stopped while the TC7 pin is driven to
the specified clear/stop level. If the TC7 pin is at the clear/stop level when a count start command is
issued (1 is written to TC7ST), counting does not start (INTTC7P does not occur) until a trigger start
edge appears, causing INTTC7T to occur (A trigger input takes precedence over a command start).
Note: For more information on the acceptance of a trigger, see 9.4.2.5 “Trigger start/stop acceptance
mode”.
(2)
Register settings
CSTC = “01”: Command start and trigger start mode
STM: Continuous/one-time output
TC7ST = “1”: Starts counting
TRGSEL: Trigger selection
Count stopped
Period (TC7DRC)
TC7 input
(Signal after
noise elimination)
PPG1
Count start
(Command)
PPG output with a period
When TRGSEL = 0
(Start on falling edge) specified with TC7DRC if
there is no trigger
Count cleared
Start
Count
cleared
Count stops with a
trigger (High level).
Count
start
Count starts with a
trigger (Falling edge).
Figure 9-8 Example Operation in Command Start and Trigger Start Mode
Page 81
9. 10-Bit Timer/Counter (TC7)
9.4 Features
TMP86CH12MG
9.4.2.3
Trigger start mode
(1)
Description
If an edge specified with the start edge selection field (TRGSEL) appears on the TC7 pin, the timer
starts counting. The counter is cleared and stopped while the TC7 pin is driven to the specified clear/
stop level.
In trigger start mode, writing a 1 to TC7ST is ignored and does not initialize the PPG output.
Note: For more information on the acceptance of a trigger, see 9.4.2.5 “Trigger start/stop acceptance
mode”.
(2)
Register settings
CSTC = “10”: Trigger start mode
STM: Continuous/one-time output
TC7ST = “1”: Starts waiting for a trigger on the TC7 pin
TRGSEL: Trigger selection
TC7 input
(Signal after
noise elimination)
Count
stopped
Count
stopped
PPG1 output
(Example)
Command set
Count
start
Count
cleared
Count
start
Count
cleared
After a command is
set, counting does not
start until a specified
trigger appears.
TC7 input
(Signal after
noise elimination)
Count
stopped
PPG1 output
(Example)
Command set
Count
start
Count
cleared
Count
start
After a command is
set, counting does not
start until a specified
trigger appears.
Figure 9-9 Example Operation in Trigger Start Mode
9.4.2.4
Trigger capture mode (CSTC = 00)
(1)
Description
When counting starts in command start and capture mode, the count values at the rising and falling
edges of the TC7 pin input are captured and stored in capture registers TC7CAPA and TC7CAPB,
respectively.
Page 82
TMP86CH12MG
The captured data is first stored in the capture buffer. At the end of the period, the data is transferred from the capture buffer to the capture register. If a trigger input does not appear within a
period, the data captured in the previous period remains in the capture buffer and is transferred to the
capture register at the end of the period. If more than one trigger edge is detected within a period, the
data captured last is written to the capture register.
Captured data must be read in the following order: Lower byte of capture register A (TC7CAPAL),
upper byte of capture register A (TC7CAPAH), lower byte of capture register B (TC7CAPBL), and
upper byte of capture register B (TC7CAPBH). Note that reading only the rising-edge captured data
(TC7CAPA) does not update the next captured data. The falling-edge captured data (TC7CAPB)
must also be read.
An attempt to read a captured value from a register other than the upper byte of the TC7CAPB
causes the capture registers to enter protected state, in which captured data cannot be updated. Reading a value from the upper byte of the TC7CAPB cancels that state, re-enabling the updating of captured data (The TC7CAPA and TC7CAPB are read as a single set of operation).
Note that the protected state may be still effective immediately after the counter starts. Ensure that
a dummy read of capture registers is performed in the first period to cancel the protected state.
The capture feature of the TC7 assumes that a capture trigger (Rising or falling edge) appears
within a period. Captured data is updated (An edge is detected) only when the timer is operating
(TC7ST = 1). If a timer stop command (TC7ST = 0) is written within a period, captured data will be
undefined. Captured data is not updated after a one-time stop command is written. In one-time stop
mode, no trigger is accepted after a STOP command is given.
(2)
Register settings
CSTC = “00”: Command start and capture mode
STM: Continuous/one-time output
TC7ST = “1”: Starts counting
Page 83
9. 10-Bit Timer/Counter (TC7)
9.4 Features
TMP86CH12MG
1 period
1 period
Rising edge
Falling edge
Rising edge
Falling edge
TC7 input
(Signal after
noise elimination)
a
b
c
a
d
c
Capture
buffers
b
d
x
a
c
y
b
d
Capture
registers
Captured values read
(Data read skipped)
Captured values read
(a and b read)
1 period
Captured values read
(c and d read)
1 period
1 period
1 period
a1
b1
a2
TC7 input
(Signal after
noise elimination)
a
b
c
a
d
c
c1
a1
c2
c1
c2
Capture
buffers
b
d
b1
a2
x
c
a1
c1
c2
y
d
d
b1
a2
Capture
registers
Captured values read
(Data read skipped)
Captured values read
(c and d read)
Started reading
other than upper
CAPB in this
period
Captured values read
(a1 and d read)
Figure 9-10 Example Operation in Trigger Capture Mode
9.4.2.5
Trigger start/stop acceptance mode
(1)
Selecting an input signal logic for the TC7 pin (Trigger input)
The logic for an input trigger signal on the TC7 pin can be specified using TC7CR1<TRGSEL> .
• TRGSEL = 0:
Counting starts on the falling edge. The counter is cleared and stopped while the TC7 pin is
high.
• TRGSEL = 1:
Counting starts on the rising edge. The counter is cleared and stopped while the TC7 pin is
low.
Page 84
TMP86CH12MG
TRGSEL = 0
TRGSEL = 1
Counter
operating
Counter
operating
Counter
operating
Counter
stopped
TC7 pin input
Counter
operating
Counter
stopped
TC7 pin input
Count
started
Count
cleared
Count
started
Count
started
Count
cleared
Count
started
Figure 9-11 Trigger Input Signal
When TRGSEL is set to 0 to select a falling-edge trigger, a falling edge detected on the TC7 pin
causes the counter to start counting and a high level on the TC7 pin causes the counter to be cleared
and the PPG output to be initialized. The counter is stopped while the TC7 pin input is high.
When TRGSEL is set to 1 to select a rising-edge trigger, a rising edge detected on the TC7 pin
causes the counter to start counting and a low level on the TC7 pin causes the counter to be cleared
and the PPG output to be initialized. The counter is stopped while the TC7 pin input is low.
In one-time stop mode, the counter accepts a stop trigger but does not accept a start trigger (when a
stop trigger is accepted within a period, the output is immediately initialized and the counter is
stopped).
Counter stopped
TC7 pin input
PPG output
Counting stop mode
with the outputs at
the end of the period
Initial value
One-time
mode
Count
cleared
All triggers (Start and stop) are ignored when the timer is stopped (TC7ST = 0).
(2)
Specifying whether triggers are always accepted or ignored when PPG outputs are
active
The TC7CR1<TRGAM> specifies whether triggers from the TC7 pin are always accepted or
ignored when the PPG output is active.
• TRGAM = 0:
Triggers from the TC7 pin are always accepted regardless of whether PPG1 and PPG2 outputs are active or inactive. A trigger starts or clears/stops the timer and deactivates PPG1 and
PPG2 outputs.
• TRGAM = 1:
Triggers from the TC7 pin are accepted only when PPG1 and PPG2 outputs are inactive. A
trigger starts or clears/stops the timer. Triggers are ignored when PPG1 and PPG2 outputs are
active.
The active/inactive state of the PPG1 or PPG2 pin has meaning only when output on the pin is
enabled with PPG1OE or PPG2OE.
Page 85
9. 10-Bit Timer/Counter (TC7)
9.4 Features
TMP86CH12MG
TC7 pin input
PPG1 output
(Positive logic)
PPG2 output
(Positive logic)
INTTC7T
INTTC7P
Counter
stopped
Counter
operating
Count
started
Count
cleared
Counter
operating
Count
started
Counter
stopped
Count
cleared
Counter Counter
operating stopped
Count
started
Count
cleared
Count
started
Counter
operating
End of
a period
Figure 9-12 Start and Clear/stop Triggers on the TC7 Pin:
Falling-edge Trigger (Counting stopped at high level), Triggers Always Accepted
(3)
Ignoring triggers when PPG outputs are active
Setting TRGAM to 1 specifies that triggers are ignored when PPG outputs are active; trigger edges
detected when PPG1 and PPG2 outputs are inactive are accepted and cause the counter to be cleared
and stopped. If a trigger is detected when PPG1 and PPG2 outputs are active, the counter does not
stop immediately but continues counting until the outputs become inactive. If the trigger signal level
is a stop level when the outputs become inactive, the counter is cleared/stopped and waits for a next
start trigger. If output is enabled for both PPG1 and PPG2, triggers are accepted only when both
PPG1 and PPG2 outputs are inactive.
Triggers not accepted
TC7 pin input
(Signal after
noise elimination)
IGBT1
(Positive logic)
IGBT2
(Positive logic)
INTTC7
INTTCR
Counter
operating
A trigger detected when
PPG1 and PPG2 are
inactive causes the
counter to stop or start.
Counter
stopped
Counter
operating
A trigger detected when
PPG1 or PPG2 is active
does not cause the
counter to stop.
Counter
stopped
Counter
operating
A high level of the trigger
input causes the counter
to stop when PPG1 and
PPG2 become inactive.
A trigger detected when
PPG1 or PPG2 is active
does not cause the
counter to stop or restart.
Figure 9-13 Start Triggers on the TC7 Pin:
Falling-edge Trigger (Counting stopped at high level), Triggers Ignored when PPG Outputs
are Active
Page 86
TMP86CH12MG
9.4.3
Configuring how the timer stops
Setting TC7ST to 0 causes the timer to stop with the specified output state according to the setting of STM.
9.4.3.1
Counting stopped with the outputs initialized
When STM is set to 00, the counter stops immediately with the PPG1 and PPG2 outputs initialized to
the values specified with PPG1INI and PPG2INI.
9.4.3.2
Counting stopped with the outputs maintained
When STM is set to 01, the counter stops immediately with the current PPG1 and PPG2 output states
maintained.
To restart the counter from the maintained state (STM = 01), set TC7ST to 1. The counter is restarted with
the initial output values, specified with PPG1INI and PPG2INI.
9.4.3.3
Counting stopped with the outputs initialized at the end of the period
When STM is set to 10, the counter continues counting until the end of the current period and then
stops. If a stop trigger is detected before the end of the period, however, the counter stops immediately.
TC7CR1 and TC7CR2 must not be rewritten before the counter stops completely.
The CNTBF flag (TC7CR3<CNTBF>) can be read to determine whether the counter has stopped.
9.4.4
One-time/continuous output mode
9.4.4.1
One-time output mode
Starting the timer (TC7ST = 1) with STM set to 10 specifies one-time output mode. In this mode, the
timer stops counting at the end of a period.
For a trigger start, the counter is stopped until a trigger is detected. A specified trigger restarts counting
and the counter stops at the end of the period or when a stop trigger is detected, after which it waits for a
trigger again.
For a command start, the counter is stopped until TC7ST is reset to 1.
TC7CR1 and TC7CR2 must not be rewritten before the counter stops completely.
The CNTBF flag (TC7CR3<CNTBF>) can be read to determine whether the counter has stopped.
TC7ST remains set to 1 after the counter is stopped.
When TC7ST is set to 1, setting STM to 10 clears the counter, which then restarts counting from the
beginning in one-time output mode.
9.4.4.2
Continuous output mode
Starting the timer (TC7ST = 1) with STM set to 00 or 01 specifies continuous output mode. In this
mode, the timer outputs specified waveforms continuously.
Page 87
9. 10-Bit Timer/Counter (TC7)
9.4 Features
TMP86CH12MG
PPG1
(Positive logic)
PPG1INI = 0
PPG2
(Negative logic)
PPG1INI = 1
The counter is forcibly
stopped and cleared,
with the outputs initialized.
Output enabled
Count started
PPG1E/PPG2E = 1 TC7ST = 1
STM = 00
STOP command
TC7ST = 0
Figure 9-14 Immediately Stopping and Clearing the Counter with the Outputs Initialized
(STM = 00)
PPG1
(Positive logic)
PPG1INI = 0
PPG2
(Negative logic)
PPG1INI = 1
Output enabled
Count started
PPG1E/PPG2E = 1 TC7ST = 1
STM = 01
STOP command
TC7ST = 0
The counter is forcibly
stopped and cleared,
with the outputs maintained.
Figure 9-15 Immediately Stopping and Clearing the Counter with the Outputs Maintained
(STM = 01)
1 period
1 period
PPG1
(Positive logic)
PPG1INI = 0
PPG2
(Negative logic)
PPG1INI = 1
After a stop command is executed,
the counter continues counting until
the end of the period.
It stops at the end of the period.
Output enabled
Count started
PPG1E/PPG2E = 1 TC7ST = 1
STM = 00 or 01
STOP command Count
TC7ST = 0
stopped
STM = 10
Figure 9-16 Stopping the Counter at the End of the Period (STM = 10)
1 period
PPG1
(Positive logic)
PPG1INI = 0
PPG2
(Negative logic)
PPG1INI = 1
The counter stops at the end of the period
and then waits for a command start or a start trigger.
Output enabled
PPG1E/PPG2E = 1
Count started
TC7ST = 1
STM = 10
Count stopped
at the end of the period
Figure 9-17 Stopping the Counter at the End of the Period (STM = 10): TC7ST = 1, One-time
Output Mode
Page 88
TMP86CH12MG
9.4.5
PPG output control (Initial value/output logic, enabling/disabling output)
9.4.5.1
Specifying initial values and output logic for PPG outputs
The PPG1INI and PPG2INI bits (TC7CR1<PPG1INI> and TC7CR1<PPG2INI>) specify the initial values of PPG1 and PPG2 outputs as well as their output logic.
(1)
Positive logic output
Setting the bit to 0 specifies that the output is initially low and driven high upon a match between
the counter value and specified dead time.
(2)
Negative logic output
Setting the bit to 1 specifies that the output is initially high and driven low upon a match between
the counter value and specified dead time.
9.4.5.2
Enabling or disabling PPG outputs
The PPG1OE and PPG2OE bits (TC7CR2<PPG1OE> and TC7CR2<PPG2OE>) specify whether PPG
outputs are enabled or disabled. When outputs are disabled, no PPG waveforms appear while the counter
is operating, allowing the PPG1 and PPG2 pins to be used as normal input/output pins.
The states of the pins when outputs are disabled depend on the settings in port registers.
9.4.5.3
Using the TC7 as a normal timer/counter
The TC7 can be used as a normal timer/counter when PPG outputs are disabled using PPG1E and
PPG2E. In that case, use an INTTC7P interrupt, which occurs upon a match with the value specified in the
data register (TC7DRC). To start the counter, use start control (TC7S) in command start and capture
mode.
Start
Source clock
0
Counter
TC7DRC
INTTC7P
1
2
3
4
N/0
1
2
3
4
5
6
7
n
Match detected
Figure 9-18 Using the TC7 as a Normal Timer/Counter
9.4.6
Eliminating noise from the TC7 pin input
A digital noise canceller eliminates noise from the input signal on the TC7 pin.
The digital noise canceller uses a sampling clock of fc/4, fc/2 or fc, as specified with NCRSEL, and samples
the signal five times. It accepts a level input which is continuous at least over the period of time required for
five samplings. Any level input which does not continue over the period of time required for five samplings is
canceled as noise.
Page 89
9. 10-Bit Timer/Counter (TC7)
9.4 Features
TMP86CH12MG
Table 9-1 Noise Canceller Settings
NCRSEL
Sampling Frequency
(Number of Samplings)
00
fc/4 (5)
01
Pulse Width Always Assumed as Noise
Pulse Width Always Assumed as Signal
At 8 MHz
At 16 MHz
16/fc [s]
2 [ms]
1 [ms]
20/fc [s]
2.5 [ms]
1.25 [ms]
fc/2 (5)
8/fc [s]
1 [ms]
500 [ns]
10/fc [s]
1.25 [ms]
0.625 [ms]
10
fc (5)
4/fc [s]
0.5 [ms]
250 [ns]
5/fc [s]
0.625 [ms]
0.3125 [ms]
11
(None)
None
–
–
(1/fc)
TC7 input
B
A
Noise canceller
F/F
Z
At 8 MHz
At 16 MHz
PPG output control
circuit
Edge detection
PPG output
S
fc
fc/4
fc/2
Sampling
clock
A
B
C
fc
Z
NCRSEL = 11
NCRSEL
1 2 3 4 5
1 2 3 4 5
fc
1
2
3
4
5
1
2
3
4
5
fc/2
1
2
3
4
1
2
3
4
5
fc/4
TC7 pin input
(after passing
through F/F)
After
noise
elimination
When NCRSEL = 00
Pulses of 16/fc or shorter are canceled.
When NCRSEL = 01
Pulses of 8/fc or shorter are canceled.
Pulses of 20/fc
or longer are assumed
as a signal.
Pulses of 10/fc or longer are assumed as a signal.
Pulses of 5/fc or longer are assumed as a signal.
When NCRSEL = 10
Pulses of 4/fc or shorter are canceled.
Figure 9-19 Noise Canceller Operation
• When NCRSEL = 00, a TC7 input level after passing through the F/F is always canceled if its duration
is 16/fc [s] or less and always assumed as a signal if its duration is 20/fc [s] or greater. After the input
signal supplied on the TC7 pin passes through the F/F, there is a delay between 21/fc [s] and 24/fc [s]
before the PPG outputs vary.
• When NCRSEL = 01, a TC7 input level after passing through the F/F is always canceled if its duration
is 8/fc [s] or less and always assumed as a signal if its duration is 10/fc [s] or greater. After the input
signal supplied on the TC7 pin passes through the F/F, there is a delay between 13/fc [s] and 14/fc [s]
before the PPG outputs vary.
• When NCRSEL = 10, a TC7 input level after passing through the F/F is always canceled if its duration
is 4/fc [s] or less and always assumed as a signal if its duration is 5/fc [s] or greater. After the input signal supplied on the TC7 pin passes through the F/F, there is a delay of 5/fc [s] before the PPG outputs
vary.
• When NCRSEL = 11, a pulse shorter than 1/fc may be assumed as a signal or canceled as noise in the
first-stage F/F. Ensure that input signal pulses are longer than 1/fc. After the input signal supplied on
the TC7 pin passes through the F/F, there is a delay of 4/fc [s] before the PPG outputs vary.
Page 90
TMP86CH12MG
Note 1: If the pin input level changes while the specified noise elimination threshold is being modified, the noise
canceller may assume noise as a pulse or cancel a pulse as noise.
Note 2: If noise occurs in synchronization with the internal sampling timing consecutively, it may be assumed as a
signal.
Note 3: The signal supplied on the TC7 pin requires 1/fc [s] or less to pass through the F/F.
9.4.7
Interrupts
The TC7 supports three interrupt sources.
9.4.7.1
INTTC7T (Trigger start interrupt)
A trigger interrupt (INTTC7T) occurs when the counter starts upon the detection of a trigger edge specified with TC7CR1<TRGST>. This interrupt does not occur with a trigger edge for clearing the count. A
trigger edge detected in trigger capture mode does not cause an interrupt. A start trigger causes an interrupt even when the counter is stopped in emergency.
1 period
Cleared
TC7 trigger
x
Counter
Count started
0
1
Cleared
2
M-2
M-1
0
1
2
0
1
2
Cleared upon match
TC7DRC
INTTC7T
INTTC7P
PPG output
Figure 9-20 Trigger Start Interrupt
9.4.7.2
INTTC7P (Period interrupt)
A period interrupt (INTTC7P) occurs when the counter starts with a command and when the counter is
cleared with the specified counter period (TC7DRC) reached, that is, at the end of a period. A match with
the set period causes an interrupt even when the counter is stopped in emergency.
Command stop
Stop at the end of period
Command start
Timer stopped
Counter
x
1
2
M-2
M-1
M, 0
1
2
M-2
Clear upon match
TC7DRC
INTTC7T
INTTC7P
PPG output
CSIDIS specifies
whether the first
INTTC7P occurs.
1 period
1 period
Figure 9-21 Period Interrupt
Page 91
M-1
M, 0
9. 10-Bit Timer/Counter (TC7)
9.4 Features
TMP86CH12MG
If a command start is specified (1 is written in TC7ST) when the TC7 pin is at a stop level, the counter
does not start (INTTC7P does not occur); a subsequent trigger start edge causes the counter to start and
INTTC7T to occur.
9.4.7.3
INTEMG (Emergency output stop interrupt)
An emergency output stop interrupt (INTEMG) occurs when the emergency output stop circuit operates
to stop PPG outputs in emergency.
9.4.8
Emergency PPG output stop feature
Setting TC7CR2<EMGIE> to 1 enables the emergency PPG output stop feature (Enables the EMG pin
input).
A low level input detected on the EMG pin causes an EMG interrupt (INTEMG) to occur with the PPG waveforms initialized (as specified with PPG1INI and PPG2INI). (Emergency PPG output stop)
This feature only disables PPG outputs without stopping the counter. Use the EMG interrupt handler routine
to stop the timer.
Note:Ensure that a low level on the EMG pin continues for at least 4/fc [s]. The emergency PPG output stop feature
may not operate normally with a low level shorter than 4/fc [s].
EMG interrupt (INTEMG)
Sampling
circuit
EMG
pin
S
Q
F/F
EMGF (Status flag)
R
Port output latch
F/F
PPG1OE
PPG2OE
EMGIE
EMGR
TC7 control register 2
F/F
PPG circuit output
TC7ST
STM
TC7 control register 3
A
B
Z
S
PPG1
PPG2
PPG1INI
PPG1OE
PPG2INI
PPG2OE
TC7 control register 1
Figure 9-22 EMG Pin
9.4.8.1
Enabling/disabling input on the EMG pin
Setting TC7CR2<EMGIE> to 1 enables input on the EMG pin and setting the bit to 0 disables input on
the pin. (Initially, EMGIE is set to 0, disabling an emergency output stop (EMG pin) input.)
The input signal on the EMG pin is valid only when its shared port pin is placed in input mode. Ensure
that the shared port pin is placed in input mode before attempting to enable the EMG pin input.
The EMG pin input is sampled using a high-frequency clock. The emergency PPG output stop feature
does not operate normally if the high-frequency clock is stopped.
9.4.8.2
Monitoring the emergency PPG output stop state
When the emergency PPG output stop feature activates, the TC7CR3<EMGF> is set to 1. 1 read from
EMGF indicates that PPG outputs are disabled by the emergency PPG output stop feature. To restart the
timer in that state, first make necessary settings for stopping the timer before canceling the emergency
PPG output stop state (by writing 1 to EMGR, bit7 of the TC7CR2) and then reconfiguring the control and
data registers to restart the timer.
Page 92
TMP86CH12MG
9.4.8.3
EMG interrupt
An EMG interrupt (INTEMG) occurs when an emergency PPG output stop input is accepted. To use an
INTEMG interrupt for some processing, ensure that the interrupt is enabled beforehand.
When the EMG pin is low with EMGIE set to 1 (EMG pin input enabled), an attempt to cancel the emergency PPG output stop state results in an interrupt being generated again, with the emergency PPG output
stop state reestablished.
An INTEMG interrupt occurs whenever a stop input is accepted when EMGIE = 1, regardless of
whether the timer is operating.
9.4.8.4
Canceling the emergency PPG output stop state
To cancel the emergency PPG output stop state, ensure that the input on the EMG pin is high, set
TC7CR3<TC7ST> to 0 and TC7CR3<STM> to 00 to stop the timer, and then set TC7CR2<EMGR> to 1.
Setting EMGR to 1 cancels the stop state only when TC7ST = 0 and STM = 00; ensure that TC7ST = 0
and STM = 00 before setting EMGR to 1.
If the input on the EMG pin is low and EMGIE = 1 when the emergency PPG output stop state is canceled, the timer re-enters the emergency PPG output stop state and an INTEMG interrupt occurs.
9.4.8.5
Restarting the timer after canceling the emergency PPG output stop state
To restart the timer after canceling the emergency PPG output stop state, reconfigure the control registers (TC7CR1, TC7CR2, TC7CR3) before restarting the timer.
The timer cannot restart in the emergency PPG output stop state. Monitor the emergency PPG output
stop state and cancel the state before reconfiguring the control registers to restart the timer. Ensure that the
control registers are reconfigured according to the appropriate procedure for configuring timer operation
control.
9.4.8.6
Response time between EMG pin input and PPG outputs being initialized
The time between a low level input being detected on the EMG pin and the PPG outputs being initialized
is up to 10/fc [s].
Page 93
9. 10-Bit Timer/Counter (TC7)
9.4 Features
TMP86CH12MG
Emergency stop
input
PPG pin output
EMG pin input
EMGIE
10/fc [s]
1.25 µs (at 8 MHz)
Output initialized
forcibly
Initial output state
Share port
in input mode
Emergency stop input
EMGR = 1,
protection feature
enabled
EMGF
(State monitor)
EMGR = 1,
cancel emergency output stop state
EMGF = 1,
emergency output
stop state
INTEMG
(EMG interrupt)
EMG interrupt
TC7ST
TC7ST = 1,
timer operating
STM
STM = 01,
timer operating
(Continuous mode)
TG7ST = 0
Specified with
an instruction
STM = 00
Emergency output
stop state
Figure 9-23 Timing between EMG Pin Input being Detected and PPG Outputs being Disabled
9.4.9
TC7 operation and microcontroller operating mode
The TC7 operates when the microcontroller is placed in NORMAL1, NORMAL2, IDLE1, or IDLE2 mode.
If the mode changes from NORMAL or IDLE to STOP, SLOW, or SLEEP while the TC7 is operating, the TC7
is initialized and stops operating.
To change the microcontroller operating mode from NORMAL or IDLE to STOP, SLOW, or SLEEP, ensure
that the TC7 timer is stopped before attempting to execute a mode change instruction.
To change the mode from STOP, SLOW, or SLEEP to NORMAL to restart the TC7, reconfigure all registers
according to the appropriate TC7 operation procedure.
Page 94
B
A
TC1㩷㫇㫀㫅
Falling
Decoder
Page 95
B
C
fc/27
fc/23
Figure 10-1 TimerCounter 1 (TC1)
S
ACAP1
TC1CR
Y
Y
S
A
B
Source
clock
Start
Clear
Selector
TC1DRA
CMP
PPG output
mode
16-bit timer register A, B
TC1DRB
16-bit up-counter
MPPG1
INTTC1 interript
S
Match
Q
Enable
Toggle
Set
Clear
Pulse width
measurement
mode
TC1S clear
TFF1
PPG output
mode
Internal
reset
Write to TC1CR
Note: Function I/O may not operate depending on I/O port setting. For more details, see the chapter "I/O Port".
Capture
Window mode
TC1 control register
TC1CK
2
A
fc/211, fs/23
Clear
Set Q
Command start
METT1
External
trigger start
D
Edge detector
Rising
External
trigger
TC1S
2
Port
(Note)
Pulse width
measurement
mode
Y
S
MCAP1
Clear
Set
Toggle
Q
Port
(Note)
㪧㪧㪞
pin
TMP86CH12MG
10. 16-Bit TimerCounter 1 (TC1)
10.1 Configuration
10. 16-Bit TimerCounter 1 (TC1)
10.2 TimerCounter Control
TMP86CH12MG
10.2 TimerCounter Control
The TimerCounter 1 is controlled by the TimerCounter 1 control register (TC1CR) and two 16-bit timer registers
(TC1DRA and TC1DRB).
Timer Register
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
TC1DRA
(0011H, 0010H)
TC1DRAH (0011H)
TC1DRAL (0010H)
(Initial value: 1111 1111 1111 1111)
Read/Write
TC1DRB
(0013H, 0012H)
TC1DRBH (0013H)
TC1DRBL (0012H)
(Initial value: 1111 1111 1111 1111)
Read/Write (Write enabled only in the PPG output mode)
TimerCounter 1 Control Register
TC1CR
(0014H)
TFF1
7
6
TFF1
ACAP1
MCAP1
METT1
MPPG1
5
4
3
TC1S
2
1
TC1CK
0
Read/Write
(Initial value: 0000 0000)
TC1M
Timer F/F1 control
0: Clear
1: Set
ACAP1
Auto capture control
0:Auto-capture disable
1:Auto-capture enable
MCAP1
Pulse width measurement mode control
0:Double edge capture
1:Single edge capture
METT1
External trigger timer
mode control
0:Trigger start
1:Trigger start and stop
MPPG1
PPG output control
0:Continuous pulse generation
1:One-shot
TC1S
TC1 start control
R/W
R/W
Timer
Extrigger
Event
Window
Pulse
00: Stop and counter clear
O
O
O
O
O
O
01: Command start
O
–
–
–
–
O
10: Rising edge start
(Ex-trigger/Pulse/PPG)
Rising edge count (Event)
Positive logic count (Window)
–
O
O
O
O
O
11: Falling edge start
(Ex-trigger/Pulse/PPG)
Falling edge count (Event)
Negative logic count (Window)
–
O
O
O
O
O
Divider
SLOW,
SLEEP
mode
NORMAL1/2, IDLE1/2 mode
TC1CK
TC1 source clock select
[Hz]
DV7CK = 0
DV7CK = 1
00
fc/211
fs/23
DV9
fs/23
01
fc/27
fc/27
DV5
–
10
fc/23
fc/23
DV1
–
11
TC1M
TC1 operating mode
select
PPG
R/W
R/W
External clock (TC1 pin input)
00: Timer/external trigger timer/event counter mode
01: Window mode
10: Pulse width measurement mode
11: PPG (Programmable pulse generate) output mode
R/W
Note 1: fc: High-frequency clock [Hz], fs: Low-frequency clock [Hz]
Note 2: The timer register consists of two shift registers. A value set in the timer register becomes valid at the rising edge of the
first source clock pulse that occurs after the upper byte (TC1DRAH and TC1DRBH) is written. Therefore, write the lower
byte and the upper byte in this order (it is recommended to write the register with a 16-bit access instruction). Writing only
the lower byte (TC1DRAL and TC1DRBL) does not enable the setting of the timer register.
Note 3: To set the mode, source clock, PPG output control and timer F/F control, write to TC1CR1 during TC1S=00. Set the timer
F/F1 control until the first timer start after setting the PPG mode.
Page 96
TMP86CH12MG
Note 4: Auto-capture can be used only in the timer, event counter, and window modes.
Note 5: To set the timer registers, the following relationship must be satisfied.
TC1DRA > TC1DRB > 1 (PPG output mode), TC1DRA > 1 (other modes)
Note 6: Set TFF1 to “0” in the mode except PPG output mode.
Note 7: Set TC1DRB after setting TC1M to the PPG output mode.
Note 8: When the STOP mode is entered, the start control (TC1S) is cleared to “00” automatically, and the timer stops. After the
STOP mode is exited, set the TC1S to use the timer counter again.
Note 9: Use the auto-capture function in the operative condition of TC1. A captured value may not be fixed if it's read after the
execution of the timer stop or auto-capture disable. Read the capture value in a capture enabled condition.
Note 10:Since the up-counter value is captured into TC1DRB by the source clock of up-counter after setting TC1CR<ACAP1> to
"1". Therefore, to read the captured value, wait at least one cycle of the internal source clock before reading TC1DRB for
the first time.
Page 97
10. 16-Bit TimerCounter 1 (TC1)
10.3 Function
TMP86CH12MG
10.3 Function
TimerCounter 1 has six types of operating modes: timer, external trigger timer, event counter, window, pulse width
measurement, programmable pulse generator output modes.
10.3.1 Timer mode
In the timer mode, the up-counter counts up using the internal clock. When a match between the up-counter and the timer
register 1A (TC1DRA) value is detected, an INTTC1 interrupt is generated and the up-counter is cleared. After being
cleared, the up-counter restarts counting. Setting TC1CR<ACAP1> to “1” captures the up-counter value into the timer register 1B (TC1DRB) with the auto-capture function. Use the auto-capture function in the operative condition of TC1. A captured value may not be fixed if it's read after the execution of the timer stop or auto-capture disable. Read the capture value
in a capture enabled condition. Since the up-counter value is captured into TC1DRB by the source clock of up-counter after
setting TC1CR<ACAP1> to "1". Therefore, to read the captured value, wait at least one cycle of the internal source clock
before reading TC1DRB for the first time.
Table 10-1 Internal Source Clock for TimerCounter 1 (Example: fc = 16 MHz, fs = 32.768 kHz)
NORMAL1/2, IDLE1/2 mode
TC1CK
SLOW, SLEEP mode
DV7CK = 0
DV7CK = 1
Resolution
[µs]
Maximum Time Setting
[s]
Resolution
[µs]
Maximum Time Setting
[s]
Resolution
[µs]
Maximum
Time Setting [s]
00
128
8.39
244.14
16.0
244.14
16.0
01
8.0
0.524
8.0
0.524
–
–
10
0.5
32.77 m
0.5
32.77 m
–
–
Example 1 :Setting the timer mode with source clock fc/211 [Hz] and generating an interrupt 1 second later
(fc = 16 MHz, TBTCR<DV7CK> = “0”)
LDW
; Sets the timer register (1 s ÷ 211/fc = 1E84H)
(TC1DRA), 1E84H
DI
SET
; IMF= “0”
(EIRL). 7
; Enables INTTC1
EI
; IMF= “1”
LD
(TC1CR), 00000000B
; Selects the source clock and mode
LD
(TC1CR), 00010000B
; Starts TC1
LD
(TC1CR), 01010000B
; ACAP1 ← 1
:
:
LD
WA, (TC1DRB)
Example 2 :Auto-capture
; Reads the capture value
Note: Since the up-counter value is captured into TC1DRB by the source clock of up-counter after setting TC1CR<ACAP1> to "1".
Therefore, to read the captured value, wait at least one cycle of the internal source clock before reading TC1DRB for the first
time.
Page 98
TMP86CH12MG
Timer start
Source clock
Counter
0
TC1DRA
?
1
2
3
n−1
4
n
0
1
2
3
4
5
6
n
Match detect
INTTC1 interruput request
Counter clear
(a) Timer mode
Source clock
m−2
Counter
m−1
m
m+1
m+2
n−1
Capture
TC1DRB
?
m−1
m
n
n+1
Capture
m+1
m+2
ACAP1
(b) Auto-capture
Figure 10-2 Timer Mode Timing Chart
Page 99
n−1
n
n+1
7
10. 16-Bit TimerCounter 1 (TC1)
10.3 Function
TMP86CH12MG
10.3.2 External Trigger Timer Mode
In the external trigger timer mode, the up-counter starts counting by the input pulse triggering of the TC1
pin, and counts up at the edge of the internal clock. For the trigger edge used to start counting, either the rising
or falling edge is defined in TC1CR<TC1S>.
• When TC1CR<METT1> is set to “1” (trigger start and stop)
When a match between the up-counter and the TC1DRA value is detected after the timer starts, the
up-counter is cleared and halted and an INTTC1 interrupt request is generated.
If the edge opposite to trigger edge is detected before detecting a match between the up-counter
and the TC1DRA, the up-counter is cleared and halted without generating an interrupt request.
Therefore, this mode can be used to detect exceeding the specified pulse by interrupt.
After being halted, the up-counter restarts counting when the trigger edge is detected.
• When TC1CR<METT1> is set to “0” (trigger start)
When a match between the up-counter and the TC1DRA value is detected after the timer starts, the
up-counter is cleared and halted and an INTTC1 interrupt request is generated.
The edge opposite to the trigger edge has no effect in count up. The trigger edge for the next counting is ignored if detecting it before detecting a match between the up-counter and the TC1DRA.
Since the TC1 pin input has the noise rejection, pulses of 4/fc [s] or less are rejected as noise. A pulse width
of 12/fc [s] or more is required to ensure edge detection. The rejection circuit is turned off in the SLOW1/2 or
SLEEP1/2 mode, but a pulse width of one machine cycle or more is required.
Example 1 :Generating an interrupt 1 ms after the rising edge of the input pulse to the TC1 pin
(fc =16 MHz)
LDW
; 1ms ÷ 27/fc = 7DH
(TC1DRA), 007DH
DI
SET
; IMF= “0”
(EIRL). 7
; Enables INTTC1 interrupt
EI
; IMF= “1”
LD
(TC1CR), 00000100B
; Selects the source clock and mode
LD
(TC1CR), 00100100B
; Starts TC1 external trigger, METT1 = 0
Example 2 :Generating an interrupt when the low-level pulse with 4 ms or more width is input to the TC1 pin
(fc =16 MHz)
LDW
; 4 ms ÷ 27/fc = 1F4H
(TC1DRA), 01F4H
DI
SET
; IMF= “0”
(EIRL). 7
; Enables INTTC1 interrupt
EI
; IMF= “1”
LD
(TC1CR), 00000100B
; Selects the source clock and mode
LD
(TC1CR), 01110100B
; Starts TC1 external trigger, METT1 = 0
Page 100
TMP86CH12MG
At the rising
edge (TC1S = 10)
Count start
Count start
TC1 pin input
Source clock
Up-counter
0
1
2
TC1DRA
3
n−1 n
4
n
Match detect
0
1
2
3
Count clear
INTTC1
interrupt request
(a) Trigger start (METT1 = 0)
Count clear
Count start
At the rising
edge (TC1S = 10)
Count start
TC1 pin input
Source clock
Up-counter
TC1DRA
0
1
2
m−1 m
3
0
1
2
n
n
3
Match detect
0
Count clear
INTTC1
interrupt request
Note: m < n
(b) Trigger start and stop (METT1 = 1)
Figure 10-3 External Trigger Timer Mode Timing Chart
Page 101
10. 16-Bit TimerCounter 1 (TC1)
10.3 Function
TMP86CH12MG
10.3.3 Event Counter Mode
In the event counter mode, the up-counter counts up at the edge of the input pulse to the TC1 pin. Either the
rising or falling edge of the input pulse is selected as the count up edge in TC1CR<TC1S>.
When a match between the up-counter and the TC1DRA value is detected, an INTTC1 interrupt is generated
and the up-counter is cleared. After being cleared, the up-counter restarts counting at each edge of the input
pulse to the TC1 pin. Since a match between the up-counter and the value set to TC1DRA is detected at the
edge opposite to the selected edge, an INTTC1 interrupt request is generated after a match of the value at the
edge opposite to the selected edge.
Two or more machine cycles are required for the low-or high-level pulse input to the TC1 pin.
Setting TC1CR<ACAP1> to “1” captures the up-counter value into TC1DRB with the auto capture function.
Use the auto-capture function in the operative condition of TC1. A captured value may not be fixed if it's read
after the execution of the timer stop or auto-capture disable. Read the capture value in a capture enabled condition. Since the up-counter value is captured into TC1DRB by the source clock of up-counter after setting
TC1CR<ACAP1> to "1". Therefore, to read the captured value, wait at least one cycle of the internal source
clock before reading TC1DRB for the first time.
Timer start
TC1 pin Input
Up-counter
TC1DRA
0
?
1
n−1
2
n
0
1
n
Match detect
INTTC1
interrput request
Counter clear
Figure 10-4 Event Counter Mode Timing Chart
Table 10-2 Input Pulse Width to TC1 Pin
Minimum Pulse Width [s]
NORMAL1/2, IDLE1/2 Mode
SLOW1/2, SLEEP1/2 Mode
High-going
23/fc
23/fs
Low-going
23/fc
23/fs
Page 102
2
At the
rising edge
(TC1S = 10)
TMP86CH12MG
10.3.4 Window Mode
In the window mode, the up-counter counts up at the rising edge of the pulse that is logical ANDed product
of the input pulse to the TC1 pin (window pulse) and the internal source clock. Either the positive logic (count
up during high-going pulse) or negative logic (count up during low-going pulse) can be selected.
When a match between the up-counter and the TC1DRA value is detected, an INTTC1 interrupt is generated
and the up-counter is cleared.
Define the window pulse to the frequency which is sufficiently lower than the internal source clock programmed with TC1CR<TC1CK>.
Count start
Count stop
Count start
Timer start
TC1 pin input
Internal clock
Counter
TC1DRA
0
?
1
2
3
4
5
6
7
0
1
2
3
7
Match detect
INTTC1
interrput request
Counter clear
(a) Positive logic (TC1S = 10)
Timer start
Count start
Count stop
Count start
TC1 pin input
Internal clock
0
Counter
TC1DRA
?
1
2
3
4
5
6
7
8
9 0
1
9
Match detect
INTTC1
interrput request
(b) Negative logic (TC1S = 11)
Figure 10-5 Window Mode Timing Chart
Page 103
Counter
clear
10. 16-Bit TimerCounter 1 (TC1)
10.3 Function
TMP86CH12MG
10.3.5 Pulse Width Measurement Mode
In the pulse width measurement mode, the up-counter starts counting by the input pulse triggering of the
TC1 pin, and counts up at the edge of the internal clock. Either the rising or falling edge of the internal clock is
selected as the trigger edge in TC1CR<TC1S>. Either the single- or double-edge capture is selected as the trigger edge in TC1CR<MCAP1>.
• When TC1CR<MCAP1> is set to “1” (single-edge capture)
Either high- or low-level input pulse width can be measured. To measure the high-level input pulse
width, set the rising edge to TC1CR<TC1S>. To measure the low-level input pulse width, set the
falling edge to TC1CR<TC1S>.
When detecting the edge opposite to the trigger edge used to start counting after the timer starts,
the up-counter captures the up-counter value into TC1DRB and generates an INTTC1 interrupt
request. The up-counter is cleared at this time, and then restarts counting when detecting the trigger
edge used to start counting.
• When TC1CR<MCAP1> is set to “0” (double-edge capture)
The cycle starting with either the high- or low-going input pulse can be measured. To measure the
cycle starting with the high-going pulse, set the rising edge to TC1CR<TC1S>. To measure the cycle
starting with the low-going pulse, set the falling edge to TC1CR<TC1S>.
When detecting the edge opposite to the trigger edge used to start counting after the timer starts,
the up-counter captures the up-counter value into TC1DRB and generates an INTTC1 interrupt
request. The up-counter continues counting up, and captures the up-counter value into TC1DRB and
generates an INTTC1 interrupt request when detecting the trigger edge used to start counting. The
up-counter is cleared at this time, and then continues counting.
Note 1: The captured value must be read from TC1DRB until the next trigger edge is detected. If not read, the captured value becomes a don’t care. It is recommended to use a 16-bit access instruction to read the captured
value from TC1DRB.
Note 2: For the single-edge capture, the counter after capturing the value stops at “1” until detecting the next edge.
Therefore, the second captured value is “1” larger than the captured value immediately after counting
starts.
Note 3: The first captured value after the timer starts may be read incorrectively, therefore, ignore the first captured
value.
Page 104
TMP86CH12MG
Example :Duty measurement (resolution fc/27 [Hz])
CLR
(INTTC1SW). 0
; INTTC1 service switch initial setting
Address set to convert INTTC1SW at each INTTC1
LD
(TC1CR), 00000110B
; Sets the TC1 mode and source clock
DI
SET
; IMF= “0”
(EIRL). 7
; Enables INTTC1
EI
LD
; IMF= “1”
(TC1CR), 00100110B
; Starts TC1 with an external trigger at MCAP1 = 0
CPL
(INTTC1SW). 0
; INTTC1 interrupt, inverts and tests INTTC1 service switch
JRS
F, SINTTC1
LD
A, (TC1DRBL)
LD
W,(TC1DRBH)
LD
(HPULSE), WA
; Stores high-level pulse width in RAM
A, (TC1DRBL)
; Reads TC1DRB (Cycle)
:
PINTTC1:
; Reads TC1DRB (High-level pulse width)
RETI
SINTTC1:
LD
LD
W,(TC1DRBH)
LD
(WIDTH), WA
; Stores cycle in RAM
:
RETI
; Duty calculation
:
VINTTC1:
DW
PINTTC1
; INTTC1 Interrupt vector
WIDTH
HPULSE
TC1 pin
INTTC1 interrupt request
INTTC1SW
Page 105
10. 16-Bit TimerCounter 1 (TC1)
10.3 Function
TMP86CH12MG
Count start
TC1 pin input
Count start
Trigger
(TC1S = "10")
Internal clock
Counter
0
1
2
3
4
1
Capture
n
n-1 n 0
TC1DRB
INTTC1
interrupt request
2
3
[Application] High-or low-level pulse width measurement
(a) Single-edge capture (MCAP1 = "1")
Count start
Count start
TC1 pin input
(TC1S = "10")
Internal clock
Counter
0
1
2
3
4
n+1
TC1DRB
n
n+1 n+2 n+3
Capture
n
m-2 m-1 m 0 1
Capture
m
INTTC1
interrupt request
[Application] (1) Cycle/frequency measurement
(2) Duty measurement
(b) Double-edge capture (MCAP1 = "0")
Figure 10-6 Pulse Width Measurement Mode
Page 106
2
TMP86CH12MG
10.3.6 Programmable Pulse Generate (PPG) Output Mode
In the programmable pulse generation (PPG) mode, an arbitrary duty pulse is generated by counting performed in the internal clock. To start the timer, TC1CR<TC1S> specifies either the edge of the input pulse to
the TC1 pin or the command start. TC1CR<MPPG1> specifies whether a duty pulse is produced continuously
or not (one-shot pulse).
• When TC1CR<MPPG1> is set to “0” (Continuous pulse generation)
When a match between the up-counter and the TC1DRB value is detected after the timer starts, the
level of the PPG pin is inverted and an INTTC1 interrupt request is generated. The up-counter continues counting. When a match between the up-counter and the TC1DRA value is detected, the level of
the PPG pin is inverted and an INTTC1 interrupt request is generated. The up-counter is cleared at
this time, and then continues counting and pulse generation.
When TC1S is cleared to “00” during PPG output, the PPG pin retains the level immediately before
the counter stops.
• When TC1CR<MPPG1> is set to “1” (One-shot pulse generation)
When a match between the up-counter and the TC1DRB value is detected after the timer starts, the
level of the PPG pin is inverted and an INTTC1 interrupt request is generated. The up-counter continues counting. When a match between the up-counter and the TC1DRA value is detected, the level of
the PPG pin is inverted and an INTTC1 interrupt request is generated. TC1CR<TC1S> is cleared to
“00” automatically at this time, and the timer stops. The pulse generated by PPG retains the same
level as that when the timer stops.
Since the output level of the PPG pin can be set with TC1CR<TFF1> when the timer starts, a positive or negative pulse can be generated. Since the inverted level of the timer F/F1 output level is output to the PPG pin,
specify TC1CR<TFF1> to “0” to set the high level to the PPG pin, and “1” to set the low level to the PPG pin.
Upon reset, the timer F/F1 is initialized to “0”.
Note 1: To change TC1DRA or TC1DRB during a run of the timer, set a value sufficiently larger than the count value
of the counter. Setting a value smaller than the count value of the counter during a run of the timer may
generate a pulse different from that specified.
Note 2: Do not change TC1CR<TFF1> during a run of the timer. TC1CR<TFF1> can be set correctly only at initialization (after reset). When the timer stops during PPG, TC1CR<TFF1> can not be set correctly from this
point onward if the PPG output has the level which is inverted of the level when the timer starts. (Setting
TC1CR<TFF1> specifies the timer F/F1 to the level inverted of the programmed value.) Therefore, the
timer F/F1 needs to be initialized to ensure an arbitrary level of the PPG output. To initialize the timer F/F1,
change TC1CR<TC1M> to the timer mode (it is not required to start the timer mode), and then set the PPG
mode. Set TC1CR<TFF1> at this time.
Note 3: In the PPG mode, the following relationship must be satisfied.
TC1DRA > TC1DRB
Note 4: Set TC1DRB after changing the mode of TC1M to the PPG mode.
Page 107
10. 16-Bit TimerCounter 1 (TC1)
10.3 Function
TMP86CH12MG
Example :Generating a pulse which is high-going for 800 µs and low-going for 200 µs
(fc = 16 MHz)
Setting port
LD
(TC1CR), 10000111B
; Sets the PPG mode, selects the source clock
LDW
(TC1DRA), 007DH
; Sets the cycle (1 ms ÷ 27/fc ms = 007DH)
LDW
(TC1DRB), 0019H
; Sets the low-level pulse width (200 µs ÷ 27/fc = 0019H)
LD
(TC1CR), 10010111B
; Starts the timer
Example :After stopping PPG, setting the PPG pin to a high-level to restart PPG
(fc = 16 MHz)
Setting port
LD
(TC1CR), 10000111B
; Sets the PPG mode, selects the source clock
LDW
(TC1DRA), 007DH
; Sets the cycle (1 ms ÷ 27/fc µs = 007DH)
LDW
(TC1DRB), 0019H
; Sets the low-level pulse width (200 µs ÷ 27/fc = 0019H)
LD
(TC1CR), 10010111B
; Starts the timer
:
:
LD
(TC1CR), 10000111B
; Stops the timer
LD
(TC1CR), 10000100B
; Sets the timer mode
LD
(TC1CR), 00000111B
; Sets the PPG mode, TFF1 = 0
LD
(TC1CR), 00010111B
; Starts the timer
I/O port output latch
shared with PPG output
Data output
Port output
enable
Q
D
PPG pin
R
Function output
TC1CR<TFF1>
Set
Write to TC1CR
Internal reset
Clear
Match to TC1DRB
Match to TC1DRA
Q
Toggle
Timer F/F1
INTTC1 interrupt request
TC1CR<TC1S> clear
Figure 10-7 PPG Output
Page 108
TMP86CH12MG
Timer start
Internal clock
Counter
0
1
TC1DRB
n
TC1DRA
m
2
n
n+1
m 0
1
2
n
n+1
m 0
1
2
Match detect
PPG pin output
INTTC1
interrupt request
Note: m > n
(a) Continuous pulse generation (TC1S = 01)
Count start
TC1 pin input
Trigger
Internal clock
Counter
0
TC1DRB
n
TC1DRA
m
1
n
n+1
m
0
PPG pin output
INTTC1
interrupt request
[Application] One-shot pulse output
(b) One-shot pulse generation (TC1S = 10)
Figure 10-8 PPG Mode Timing Chart
Page 109
Note: m > n
10. 16-Bit TimerCounter 1 (TC1)
10.3 Function
TMP86CH12MG
Page 110
TMP86CH12MG
11. 8-Bit TimerCounter (TC3, TC4)
11.1 Configuration
PWM mode
Overflow
fc/211 or fs/23
fc/27
5
fc/2
fc/23
fs
fc/2
fc
TC4 pin
A
B
C
D
E
F
G
H
Y
A
B
INTTC4
interrupt request
Clear
Y
8-bit up-counter
TC4S
S
PDO, PPG mode
A
B
S
16-bit
mode
S
TC4M
TC4S
TFF4
Toggle
Q
Set
Clear
Y
16-bit mode
Timer, Event
Counter mode
S
TC4CK
PDO4/PWM4/
PPG4 pin
Timer F/F4
A
Y
TC4CR
B
TTREG4
PWM, PPG mode
PWREG4
DecodeEN
PDO, PWM,
PPG mode
TFF4
16-bit
mode
TC3S
PWM mode
fc/211 or fs/23
fc/27
5
fc/2
3
fc/2
fs
fc/2
fc
TC3 pin
Y
8-bit up-counter
Overflow
16-bit mode
PDO mode
16-bit mode
Timer,
Event Couter mode
S
TC3M
TC3S
TFF3
INTTC3
interrupt request
Clear
A
B
C
D
E
F
G
H
Toggle
Q
Set
Clear
PDO3/PWM3/
pin
Timer F/F3
TC3CK
TC3CR
PWM mode
TTREG3
PWREG3
DecodeEN
TFF3
Figure 11-1 8-Bit TimerCouter 3, 4
Page 111
PDO, PWM mode
16-bit mode
11. 8-Bit TimerCounter (TC3, TC4)
11.1 Configuration
TMP86CH12MG
11.2 TimerCounter Control
The TimerCounter 3 is controlled by the TimerCounter 3 control register (TC3CR) and two 8-bit timer registers
(TTREG3, PWREG3).
TimerCounter 3 Timer Register
TTREG3
(0019H)
R/W
7
PWREG3
(0017H)
R/W
7
6
5
4
3
2
1
0
(Initial value: 1111 1111)
6
5
4
3
2
1
0
(Initial value: 1111 1111)
Note 1: Do not change the timer register (TTREG3) setting while the timer is running.
Note 2: Do not change the timer register (PWREG3) setting in the operating mode except the 8-bit and 16-bit PWM modes while
the timer is running.
TimerCounter 3 Control Register
TC3CR
(0015H)
TFF3
7
TFF3
6
5
4
TC3CK
Time F/F3 control
3
2
TC3S
0:
1:
1
0
TC3M
(Initial value: 0000 0000)
Clear
Set
R/W
NORMAL1/2, IDLE1/2 mode
TC3CK
Operating clock selection [Hz]
DV7CK = 0
DV7CK = 1
SLOW1/2
SLEEP1/2
mode
000
fc/211
fs/23
fs/23
001
fc/27
fc/27
–
010
fc/25
fc/25
–
011
fc/23
fc/23
–
100
fs
fs
fs
101
fc/2
fc/2
–
110
fc
fc
fc (Note 8)
111
TC3S
TC3 start control
0:
1:
000:
001:
TC3M
TC3M operating mode select
010:
011:
1**:
R/W
TC3 pin input
Operation stop and counter clear
Operation start
R/W
8-bit timer/event counter mode
8-bit programmable divider output (PDO) mode
8-bit pulse width modulation (PWM) output mode
16-bit mode
(Each mode is selectable with TC4M.)
Reserved
R/W
Note 1: fc: High-frequency clock [Hz] fs: Low-frequency clock[Hz]
Note 2: Do not change the TC3M, TC3CK and TFF3 settings while the timer is running.
Note 3: To stop the timer operation (TC3S= 1 → 0), do not change the TC3M, TC3CK and TFF3 settings. To start the timer operation (TC3S= 0 → 1), TC3M, TC3CK and TFF3 can be programmed.
Note 4: To use the TimerCounter in the 16-bit mode, set the operating mode by programming TC4CR<TC4M>, where TC3M must
be fixed to 011.
Note 5: To use the TimerCounter in the 16-bit mode, select the source clock by programming TC3CK. Set the timer start control
and timer F/F control by programming TC4CR<TC4S> and TC4CR<TFF4>, respectively.
Note 6: The operating clock settings are limited depending on the timer operating mode. For the detailed descriptions, see Table
11-1 and Table 11-2.
Page 112
TMP86CH12MG
Note 7: The timer register settings are limited depending on the timer operating mode. For the detailed descriptions, see Table 113.
Note 8: The operating clock fc in the SLOW or SLEEP mode can be used only as the high-frequency warm-up mode.
Page 113
11. 8-Bit TimerCounter (TC3, TC4)
11.1 Configuration
TMP86CH12MG
The TimerCounter 4 is controlled by the TimerCounter 4 control register (TC4CR) and two 8-bit timer registers
(TTREG4 and PWREG4).
TimerCounter 4 Timer Register
TTREG4
(001AH)
R/W
7
PWREG4
(0018H) R/
W
7
6
5
4
3
2
1
0
(Initial value: 1111 1111)
6
5
4
3
2
1
0
(Initial value: 1111 1111)
Note 1: Do not change the timer register (TTREG4) setting while the timer is running.
Note 2: Do not change the timer register (PWREG4) setting in the operating mode except the 8-bit and 16-bit PWM modes while
the timer is running.
TimerCounter 4 Control Register
TC4CR
(0016H)
TFF4
7
TFF4
6
5
4
TC4CK
Timer F/F4 control
3
2
TC4S
0:
1:
1
0
TC4M
(Initial value: 0000 0000)
Clear
Set
R/W
NORMAL1/2, IDLE1/2 mode
TC4CK
Operating clock selection [Hz]
DV7CK = 0
DV7CK = 1
SLOW1/2
SLEEP1/2
mode
000
fc/211
fs/23
fs/23
001
fc/27
fc/27
–
010
fc/25
fc/25
–
011
fc/2
3
3
–
100
fs
fs
fs
101
fc/2
fc/2
–
110
fc
fc
–
111
TC4S
TC4 start control
0:
1:
000:
001:
010:
TC4M
TC4M operating mode select
011:
100:
101:
110:
111:
fc/2
R/W
TC4 pin input
Operation stop and counter clear
Operation start
R/W
8-bit timer/event counter mode
8-bit programmable divider output (PDO) mode
8-bit pulse width modulation (PWM) output mode
Reserved
16-bit timer/event counter mode
Warm-up counter mode
16-bit pulse width modulation (PWM) output mode
16-bit PPG mode
R/W
Note 1: fc: High-frequency clock [Hz] fs: Low-frequency clock [Hz]
Note 2: Do not change the TC4M, TC4CK and TFF4 settings while the timer is running.
Note 3: To stop the timer operation (TC4S= 1 → 0), do not change the TC4M, TC4CK and TFF4 settings.
To start the timer operation (TC4S= 0 → 1), TC4M, TC4CK and TFF4 can be programmed.
Note 4: When TC4M= 1** (upper byte in the 16-bit mode), the source clock becomes the TC4 overflow signal regardless of the
TC3CK setting.
Note 5: To use the TimerCounter in the 16-bit mode, select the operating mode by programming TC4M, where TC3CR<TC3 M>
must be set to 011.
Page 114
TMP86CH12MG
Note 6: To the TimerCounter in the 16-bit mode, select the source clock by programming TC3CR<TC3CK>. Set the timer start
control and timer F/F control by programming TC4S and TFF4, respectively.
Note 7: The operating clock settings are limited depending on the timer operating mode. For the detailed descriptions, see Table
11-1 and Table 11-2.
Note 8: The timer register settings are limited depending on the timer operating mode. For the detailed descriptions, see Table 113.
Table 11-1 Operating Mode and Selectable Source Clock (NORMAL1/2 and IDLE1/2 Modes)
Operating mode
fc/211
or
fc/27
fc/25
fc/23
fs
fc/2
fc
TC3
pin input
TC4
pin input
fs/23
8-bit timer
Ο
Ο
Ο
Ο
–
–
–
–
–
8-bit event counter
–
–
–
–
–
–
–
Ο
Ο
8-bit PDO
Ο
Ο
Ο
Ο
–
–
–
–
–
8-bit PWM
Ο
Ο
Ο
Ο
Ο
Ο
Ο
–
–
16-bit timer
Ο
Ο
Ο
Ο
–
–
–
–
–
16-bit event counter
–
–
–
–
–
–
–
Ο
–
Warm-up counter
–
–
–
–
Ο
–
–
–
–
16-bit PWM
Ο
Ο
Ο
Ο
Ο
Ο
Ο
Ο
–
16-bit PPG
Ο
Ο
Ο
Ο
–
–
–
Ο
–
Note 1: For 16-bit operations (16-bit timer/event counter, warm-up counter, 16-bit PWM and 16-bit PPG), set its source clock on
lower bit (TC3CK).
Note 2: Ο : Available source clock
Table 11-2 Operating Mode and Selectable Source Clock (SLOW1/2 and SLEEP1/2 Modes)
Operating mode
fc/211
or
fc/27
fc/25
fc/23
fs
fc/2
fc
TC3
pin input
TC4
pin input
fs/23
8-bit timer
Ο
–
–
–
–
–
–
–
–
8-bit event counter
–
–
–
–
–
–
–
Ο
Ο
8-bit PDO
Ο
–
–
–
–
–
–
–
–
8-bit PWM
Ο
–
–
–
Ο
–
–
–
–
16-bit timer
Ο
–
–
–
–
–
–
–
–
16-bit event counter
–
–
–
–
–
–
–
Ο
–
Warm-up counter
–
–
–
–
–
–
Ο
–
–
16-bit PWM
Ο
–
–
–
Ο
–
–
Ο
–
16-bit PPG
Ο
–
–
–
–
–
–
Ο
–
Note1: For 16-bit operations (16-bit timer/event counter, warm-up counter, 16-bit PWM and 16-bit PPG), set its source clock on
lower bit (TC3CK).
Note2: Ο : Available source clock
Page 115
11. 8-Bit TimerCounter (TC3, TC4)
11.1 Configuration
TMP86CH12MG
Table 11-3 Constraints on Register Values Being Compared
Operating mode
Register Value
8-bit timer/event counter
1≤ (TTREGn) ≤255
8-bit PDO
1≤ (TTREGn) ≤255
8-bit PWM
2≤ (PWREGn) ≤254
16-bit timer/event counter
1≤ (TTREG4, 3) ≤65535
Warm-up counter
256≤ (TTREG4, 3) ≤65535
16-bit PWM
2≤ (PWREG4, 3) ≤65534
1≤ (PWREG4, 3) < (TTREG4, 3) ≤65535
16-bit PPG
and
(PWREG4, 3) + 1 < (TTREG4, 3)
Note: n = 3 to 4
Page 116
TMP86CH12MG
11.3 Function
The TimerCounter 3 and 4 have the 8-bit timer, 8-bit event counter, 8-bit programmable divider output (PDO), 8bit pulse width modulation (PWM) output modes. The TimerCounter 3 and 4 (TC3, 4) are cascadable to form a 16bit timer. The 16-bit timer has the operating modes such as the 16-bit timer, 16-bit event counter, warm-up counter,
16-bit pulse width modulation (PWM) output and 16-bit programmable pulse generation (PPG) modes.
11.3.1 8-Bit Timer Mode (TC3 and 4)
In the timer mode, the up-counter counts up using the internal clock. When a match between the up-counter
and the timer register j (TTREGj) value is detected, an INTTCj interrupt is generated and the up-counter is
cleared. After being cleared, the up-counter restarts counting.
Note 1: In the timer mode, fix TCjCR<TFFj> to 0. If not fixed, the PDOj, PWMj and PPGj pins may output pulses.
Note 2: In the timer mode, do not change the TTREGj setting while the timer is running. Since TTREGj is not in the
shift register configuration in the timer mode, the new value programmed in TTREGj is in effect immediately
after the programming. Therefore, if TTREGi is changed while the timer is running, an expected operation
may not be obtained.
Note 3: j = 3, 4
Table 11-4 Source Clock for TimerCounter 3, 4 (Internal Clock)
Source Clock
NORMAL1/2, IDLE1/2 mode
Resolution
Repeated Cycle
DV7CK = 0
DV7CK = 1
SLOW1/2,
SLEEP1/2
mode
fc/211 [Hz]
fs/23 [Hz]
fs/23 [Hz]
128 µs
244.14 µs
32.6 ms
62.3 ms
fc/27
fc/27
–
8 µs
–
2.0 ms
–
fc/25
fc/25
–
2 µs
–
510 µs
–
fc/23
fc/23
–
500 ns
–
127.5 µs
–
fc = 16 MHz
fs = 32.768 kHz
fc = 16 MHz
fs = 32.768 kHz
Example :Setting the timer mode with source clock fc/27 Hz and generating an interrupt 80 µs later
(TimerCounter4, fc = 16.0 MHz)
(TTREG4), 0AH
: Sets the timer register (80 µs÷27/fc = 0AH).
(EIRH). 5
: Enables INTTC4 interrupt.
LD
(TC4CR), 00010000B
: Sets the operating cock to fc/27, and 8-bit timer mode.
LD
(TC4CR), 00011000B
: Starts TC4.
LD
DI
SET
EI
Page 117
11. 8-Bit TimerCounter (TC3, TC4)
11.1 Configuration
TMP86CH12MG
TC4CR<TC4S>
Internal
Source Clock
1
Counter
TTREG4
?
2
3
n-1
n 0
1
2
n-1
n 0
1
2
0
n
Match detect
Counter clear
INTTC4 interrupt request
Counter clear
Match detect
Figure 11-2 8-Bit Timer Mode Timing Chart (TC4)
11.3.2 8-Bit Event Counter Mode (TC3, 4)
In the 8-bit event counter mode, the up-counter counts up at the falling edge of the input pulse to the TCj pin.
When a match between the up-counter and the TTREGj value is detected, an INTTCj interrupt is generated and
the up-counter is cleared. After being cleared, the up-counter restarts counting at the falling edge of the input
pulse to the TCj pin. Two machine cycles are required for the low- or high-level pulse input to the TCj pin.
Therefore, a maximum frequency to be supplied is fc/24 Hz in the NORMAL1/2 or IDLE1/2 mode, and fs/24
Hz in the SLOW1/2 or SLEEP1/2 mode.
Note 1: In the event counter mode, fix TCjCR<TFFj> to 0. If not fixed, the PDOj, PWMj and PPGj pins may output
pulses.
Note 2: In the event counter mode, do not change the TTREGj setting while the timer is running. Since TTREGj is
not in the shift register configuration in the event counter mode, the new value programmed in TTREGj is in
effect immediately after the programming. Therefore, if TTREGi is changed while the timer is running, an
expected operation may not be obtained.
Note 3: j = 3, 4
TC4CR<TC4S>
TC4 pin input
0
Counter
TTREG4
?
1
2
n-1
n 0
1
2
n-1
n 0
1
2
0
n
Match detect
INTTC4 interrupt request
Counter
clear
Match detect
Counter
clear
Figure 11-3 8-Bit Event Counter Mode Timing Chart (TC4)
11.3.3 8-Bit Programmable Divider Output (PDO) Mode (TC3, 4)
This mode is used to generate a pulse with a 50% duty cycle from the PDOj pin.
In the PDO mode, the up-counter counts up using the internal clock. When a match between the up-counter
and the TTREGj value is detected, the logic level output from the PDOj pin is switched to the opposite state and
the up-counter is cleared. The INTTCj interrupt request is generated at the time. The logic state opposite to the
timer F/Fj logic level is output from the PDOj pin. An arbitrary value can be set to the timer F/Fj by
TCjCR<TFFj>. Upon reset, the timer F/Fj value is initialized to 0.
To use the programmable divider output, set the output latch of the I/O port to 1.
Page 118
TMP86CH12MG
Example :Generating 1024 Hz pulse using TC4 (fc = 16.0 MHz)
Setting port
LD
(TTREG4), 3DH
: 1/1024÷27/fc÷2 = 3DH
LD
(TC4CR), 00010001B
: Sets the operating clock to fc/27, and 8-bit PDO mode.
LD
(TC4CR), 00011001B
: Starts TC4.
Note 1: In the programmable divider output mode, do not change the TTREGj setting while the timer is running.
Since TTREGj is not in the shift register configuration in the programmable divider output mode, the new
value programmed in TTREGj is in effect immediately after programming. Therefore, if TTREGi is changed
while the timer is running, an expected operation may not be obtained.
Note 2: When the timer is stopped during PDO output, the PDOj pin holds the output status when the timer is
stopped. To change the output status, program TCjCR<TFFj> after the timer is stopped. Do not change the
TCjCR<TFFj> setting upon stopping of the timer.
Example: Fixing the PDOj pin to the high level when the TimerCounter is stopped
CLR (TCjCR).3: Stops the timer.
CLR (TCjCR).7: Sets the PDOj pin to the high level.
Note 3: j = 3, 4
Page 119
Page 120
?
INTTC4 interrupt request
PDO4 pin
Timer F/F4
TTREG4
Counter
Internal
source clock
TC4CR<TFF4>
TC4CR<TC4S>
0
n
1
Match detect
2
n 0
1
Match detect
2
n 0
1
Match detect
2
n 0
1
Match detect
2
n 0
1
2
3
Set F/F
Held at the level when the timer
is stopped
0
Write of "1"
11.1 Configuration
11. 8-Bit TimerCounter (TC3, TC4)
TMP86CH12MG
Figure 11-4 8-Bit PDO Mode Timing Chart (TC4)
TMP86CH12MG
11.3.4 8-Bit Pulse Width Modulation (PWM) Output Mode (TC3, 4)
This mode is used to generate a pulse-width modulated (PWM) signals with up to 8 bits of resolution. The
up-counter counts up using the internal clock.
When a match between the up-counter and the PWREGj value is detected, the logic level output from the
timer F/Fj is switched to the opposite state. The counter continues counting. The logic level output from the
timer F/Fj is switched to the opposite state again by the up-counter overflow, and the counter is cleared. The
INTTCj interrupt request is generated at this time.
Since the initial value can be set to the timer F/Fj by TCjCR<TFFj>, positive and negative pulses can be generated. Upon reset, the timer F/Fj is cleared to 0.
(The logic level output from the PWMj pin is the opposite to the timer F/Fj logic level.)
Since PWREGj in the PWM mode is serially connected to the shift register, the value set to PWREGj can be
changed while the timer is running. The value set to PWREGj during a run of the timer is shifted by the
INTTCj interrupt request and loaded into PWREGj. While the timer is stopped, the value is shifted immediately after the programming of PWREGj. If executing the read instruction to PWREGj during PWM output,
the value in the shift register is read, but not the value set in PWREGj. Therefore, after writing to PWREGj, the
reading data of PWREGj is previous value until INTTCj is generated.
For the pin used for PWM output, the output latch of the I/O port must be set to 1.
Note 1: In the PWM mode, program the timer register PWREGj immediately after the INTTCj interrupt request is
generated (normally in the INTTCj interrupt service routine.) If the programming of PWREGj and the interrupt request occur at the same time, an unstable value is shifted, that may result in generation of the pulse
different from the programmed value until the next INTTCj interrupt request is generated.
Note 2: When the timer is stopped during PWM output, the PWMj pin holds the output status when the timer is
stopped. To change the output status, program TCjCR<TFFj> after the timer is stopped. Do not change the
TCjCR<TFFj> upon stopping of the timer.
Example: Fixing the PWMj pin to the high level when the TimerCounter is stopped
CLR (TCjCR).3: Stops the timer.
CLR (TCjCR).7: Sets the PWMj pin to the high level.
Note 3: To enter the STOP mode during PWM output, stop the timer and then enter the STOP mode. If the STOP
mode is entered without stopping the timer when fc, fc/2 or fs is selected as the source clock, a pulse is output from the PWMj pin during the warm-up period time after exiting the STOP mode.
Note 4: j = 3, 4
Table 11-5 PWM Output Mode
Source Clock
NORMAL1/2, IDLE1/2 mode
Resolution
Repeated Cycle
DV7CK = 0
DV7CK = 1
SLOW1/2,
SLEEP1/2
mode
fc/211 [Hz]
fs/23 [Hz]
fs/23 [Hz]
128 µs
244.14 µs
32.8 ms
62.5 ms
fc/2
7
–
8 µs
–
2.05 ms
–
fc/2
5
–
2 µs
–
512 µs
–
fc/2
7
fc/2
5
fc = 16 MHz
fs = 32.768 kHz
fc = 16 MHz
fs = 32.768 kHz
fc/23
fc/23
–
500 ns
–
128 µs
–
fs
fs
fs
30.5 µs
30.5 µs
7.81 ms
7.81 ms
fc/2
fc/2
–
125 ns
–
32 µs
–
fc
fc
–
62.5 ns
–
16 µs
–
Page 121
Page 122
?
Shift registar
0
Shift
INTTC4 interrupt request
PWM4 pin
Timer F/F4
?
PWREG4
Counter
Internal
source clock
TC4CR<TFF4>
TC4CR<TC4S>
n
n
n
Match detect
1
n
n+1
Shift
FF
0
n
n
n+1
m
One cycle period
Write to PWREG4
Match detect
1
Shift
FF
0
m
m
m+1
p
Write to PWREG4
Match detect
m
1
Shift
FF
0
p
p
Match detect
1
p
11.1 Configuration
11. 8-Bit TimerCounter (TC3, TC4)
TMP86CH12MG
Figure 11-5 8-Bit PWM Mode Timing Chart (TC4)
TMP86CH12MG
11.3.5 16-Bit Timer Mode (TC3 and 4)
In the timer mode, the up-counter counts up using the internal clock. The TimerCounter 3 and 4 are cascadable to form a 16-bit timer.
When a match between the up-counter and the timer register (TTREG3, TTREG4) value is detected after the
timer is started by setting TC4CR<TC4S> to 1, an INTTC4 interrupt is generated and the up-counter is cleared.
After being cleared, the up-counter continues counting. Program the upper byte and lower byte in this order in
the timer register. (Programming only the upper or lower byte should not be attempted.)
Note 1: In the timer mode, fix TCjCR<TFFj> to 0. If not fixed, the PDOj, PWMj, and PPGj pins may output a pulse.
Note 2: In the timer mode, do not change the TTREGj setting while the timer is running. Since TTREGj is not in the
shift register configuration in the timer mode, the new value programmed in TTREGj is in effect immediately
after programming of TTREGj. Therefore, if TTREGj is changed while the timer is running, an expected
operation may not be obtained.
Note 3: j = 3, 4
Table 11-6 Source Clock for 16-Bit Timer Mode
Source Clock
Resolution
NORMAL1/2, IDLE1/2 mode
Repeated Cycle
DV7CK = 0
DV7CK = 1
SLOW1/2,
SLEEP1/2
mode
fc/211
fs/23
fs/23
128 µs
244.14 µs
8.39 s
16 s
fc/27
fc/27
–
8 µs
–
524.3 ms
–
fc/25
fc/25
–
2 µs
–
131.1 ms
–
fc/23
fc/23
–
500 ns
–
32.8 ms
–
fc = 16 MHz
fs = 32.768 kHz
fc = 16 MHz
fs = 32.768 kHz
Example :Setting the timer mode with source clock fc/27 Hz, and generating an interrupt 300 ms later
(fc = 16.0 MHz)
(TTREG3), 927CH
: Sets the timer register (300 ms÷27/fc = 927CH).
(EIRH). 5
: Enables INTTC4 interrupt.
LD
(TC3CR), 13H
:Sets the operating cock to fc/27, and 16-bit timer mode
(lower byte).
LD
(TC4CR), 04H
: Sets the 16-bit timer mode (upper byte).
LD
(TC4CR), 0CH
: Starts the timer.
LDW
DI
SET
EI
TC4CR<TC4S>
Internal
source clock
0
Counter
TTREG3
(Lower byte)
TTREG4
(Upper byte)
?
?
INTTC4 interrupt request
1
2
3
mn-1 mn 0
1
2
mn-1 mn 0
1
n
m
Match
detect
Counter
clear
Match
detect
Counter
clear
Figure 11-6 16-Bit Timer Mode Timing Chart (TC3 and TC4)
Page 123
2
0
11. 8-Bit TimerCounter (TC3, TC4)
11.1 Configuration
TMP86CH12MG
11.3.6 16-Bit Event Counter Mode (TC3 and 4)
In the event counter mode, the up-counter counts up at the falling edge to the TC3 pin. The TimerCounter 3
and 4 are cascadable to form a 16-bit event counter.
When a match between the up-counter and the timer register (TTREG3, TTREG4) value is detected after
the timer is started by setting TC4CR<TC4S> to 1, an INTTC4 interrupt is generated and the up-counter is
cleared.
After being cleared, the up-counter restarts counting at the falling edge of the input pulse to the TC3 pin.
Two machine cycles are required for the low- or high-level pulse input to the TC3 pin.
Therefore, a maximum frequency to be supplied is fc/24 Hz in the NORMAL1 or IDLE1 mode, and fs/24 in
the SLOW1/2 or SLEEP1/2 mode. Program the lower byte (TTREG3), and upper byte (TTREG4) in this
order in the timer register. (Programming only the upper or lower byte should not be attempted.)
Note 1: In the event counter mode, fix TCjCR<TFFj> to 0. If not fixed, the PDOj, PWMj and PPGj pins may output pulses.
Note 2: In the event counter mode, do not change the TTREGj setting while the timer is running. Since TTREGj is not in
the shift register configuration in the event counter mode, the new value programmed in TTREGj is in effect immediately after the programming. Therefore, if TTREGj is changed while the timer is running, an expected operation
may not be obtained.
Note 3: j = 3, 4
11.3.7 16-Bit Pulse Width Modulation (PWM) Output Mode (TC3 and 4)
This mode is used to generate a pulse-width modulated (PWM) signals with up to 16 bits of resolution. The
TimerCounter 3 and 4 are cascadable to form the 16-bit PWM signal generator.
The counter counts up using the internal clock or external clock.
When a match between the up-counter and the timer register (PWREG3, PWREG4) value is detected, the
logic level output from the timer F/F4 is switched to the opposite state. The counter continues counting. The
logic level output from the timer F/F4 is switched to the opposite state again by the counter overflow, and the
counter is cleared. The INTTC4 interrupt is generated at this time.
Two machine cycles are required for the high- or low-level pulse input to the TC3 pin. Therefore, a maximum frequency to be supplied is fc/24 Hz in the NORMAL1 or IDLE1 mode, and fs/24 to in the SLOW1/2 or
SLEEP1/2 mode.
Since the initial value can be set to the timer F/F4 by TC4CR<TFF4>, positive and negative pulses can be
generated. Upon reset, the timer F/F4 is cleared to 0.
(The logic level output from the PWM4 pin is the opposite to the timer F/F4 logic level.)
Since PWREG4 and 3 in the PWM mode are serially connected to the shift register, the values set to
PWREG4 and 3 can be changed while the timer is running. The values set to PWREG4 and 3 during a run of
the timer are shifted by the INTTCj interrupt request and loaded into PWREG4 and 3. While the timer is
stopped, the values are shifted immediately after the programming of PWREG4 and 3. Set the lower byte
(PWREG3) and upper byte (PWREG3) in this order to program PWREG4 and 3. (Programming only the lower
or upper byte of the register should not be attempted.)
If executing the read instruction to PWREG4 and 3 during PWM output, the values set in the shift register is
read, but not the values set in PWREG4 and 3. Therefore, after writing to the PWREG4 and 3, reading data of
PWREG4 and 3 is previous value until INTTC4 is generated.
For the pin used for PWM output, the output latch of the I/O port must be set to 1.
Note 1: In the PWM mode, program the timer register PWREG4 and 3 immediately after the INTTC4 interrupt
request is generated (normally in the INTTC4 interrupt service routine.) If the programming of PWREGj and
the interrupt request occur at the same time, an unstable value is shifted, that may result in generation of
pulse different from the programmed value until the next INTTC4 interrupt request is generated.
Note 2: When the timer is stopped during PWM output, the PWM4 pin holds the output status when the timer is
stopped. To change the output status, program TC4CR<TFF4> after the timer is stopped. Do not program
TC4CR<TFF4> upon stopping of the timer.
Example: Fixing thePWM4 pin to the high level when the TimerCounter is stopped
Page 124
TMP86CH12MG
CLR (TC4CR).3: Stops the timer.
CLR (TC4CR).7 : Sets the PWM4 pin to the high level.
Note 3: To enter the STOP mode, stop the timer and then enter the STOP mode. If the STOP mode is entered without stopping of the timer when fc, fc/2 or fs is selected as the source clock, a pulse is output from the PWM4
pin during the warm-up period time after exiting the STOP mode.
Table 11-7 16-Bit PWM Output Mode
Source Clock
NORMAL1/2, IDLE1/2 mode
Resolution
Repeated Cycle
DV7CK = 0
DV7CK = 1
SLOW1/2,
SLEEP1/2
mode
fc/211
fs/23 [Hz]
fs/23 [Hz]
128 µs
244.14 µs
8.39 s
16 s
fc/27
fc/27
–
8 µs
–
524.3 ms
–
fc/25
fc/25
–
2 µs
–
131.1 ms
–
fc/23
fc/23
–
500ns
–
32.8 ms
–
fc = 16 MHz
fs = 32.768 kHz
fc = 16 MHz
fs = 32.768 kHz
fs
fs
fs
30.5 µs
30.5 µs
fc/2
fc/2
–
125 ns
–
8.2 ms
–
fc
fc
–
62.5 ns
–
4.1 ms
–
2
s
Example :Generating a pulse with 1-ms high-level width and a period of 32.768 ms (fc = 16.0 MHz)
Setting ports
LDW
(PWREG3), 07D0H
: Sets the pulse width.
LD
(TC3CR), 33H
: Sets the operating clock to fc/23, and 16-bit PWM output
mode (lower byte).
LD
(TC4CR), 056H
: Sets TFF4 to the initial value 0, and 16-bit PWM signal
generation mode (upper byte).
LD
(TC4CR), 05EH
: Starts the timer.
Page 125
2s
Page 126
?
?
PWREG4
(Upper byte)
16-bit
shift register
0
a
Shift
INTTC4 interrupt request
PWM4 pin
Timer F/F4
?
PWREG3
(Lower byte)
Counter
Internal
source clock
TC4CR<TFF4>
TC4CR<TC4S>
an
n
an
Match detect
1
an
an+1
Shift
FFFF
0
an
an
an+1
m
b
One cycle period
Write to PWREG4
Write to PWREG3
Match detect
1
Shift
FFFF
0
bm
bm bm+1
p
c
Write to PWREG4
Write to PWREG3
Match detect
bm
1
Shift
FFFF
0
cp
Match detect
cp
1
cp
11.1 Configuration
11. 8-Bit TimerCounter (TC3, TC4)
TMP86CH12MG
Figure 11-7 16-Bit PWM Mode Timing Chart (TC3 and TC4)
TMP86CH12MG
11.3.8 16-Bit Programmable Pulse Generate (PPG) Output Mode (TC3 and 4)
This mode is used to generate pulses with up to 16-bits of resolution. The timer counter 3 and 4 are cascadable to enter the 16-bit PPG mode.
The counter counts up using the internal clock or external clock. When a match between the up-counter and
the timer register (PWREG3, PWREG4) value is detected, the logic level output from the timer F/F4 is
switched to the opposite state. The counter continues counting. The logic level output from the timer F/F4 is
switched to the opposite state again when a match between the up-counter and the timer register (TTREG3,
TTREG4) value is detected, and the counter is cleared. The INTTC4 interrupt is generated at this time.
Two machine cycles are required for the high- or low-level pulse input to the TC3 pin. Therefore, a maximum frequency to be supplied is fc/24 Hz in the NORMAL1 or IDLE1 mode, and fc/24 to in the SLOW1/2 or
SLEEP1/2 mode.
Since the initial value can be set to the timer F/F4 by TC4CR<TFF4>, positive and negative pulses can be
generated. Upon reset, the timer F/F4 is cleared to 0.
(The logic level output from the PPG4 pin is the opposite to the timer F/F4.)
Set the lower byte and upper byte in this order to program the timer register. (TTREG3 → TTREG4,
PWREG3 → PWREG4) (Programming only the upper or lower byte should not be attempted.)
For PPG output, set the output latch of the I/O port to 1.
Example :Generating a pulse with 1-ms high-level width and a period of 16.385 ms (fc = 16.0 MHz)
Setting ports
LDW
(PWREG3), 07D0H
: Sets the pulse width.
LDW
(TTREG3), 8002H
: Sets the cycle period.
LD
(TC3CR), 33H
: Sets the operating clock to fc/23, and16-bit PPG mode
(lower byte).
LD
(TC4CR), 057H
: Sets TFF4 to the initial value 0, and 16-bit
PPG mode (upper byte).
LD
(TC4CR), 05FH
: Starts the timer.
Note 1: In the PPG mode, do not change the PWREGi and TTREGi settings while the timer is running. Since
PWREGi and TTREGi are not in the shift register configuration in the PPG mode, the new values programmed in PWREGi and TTREGi are in effect immediately after programming PWREGi and TTREGi.
Therefore, if PWREGi and TTREGi are changed while the timer is running, an expected operation may not
be obtained.
Note 2: When the timer is stopped during PPG output, the PPG4 pin holds the output status when the timer is
stopped. To change the output status, program TC4CR<TFF4> after the timer is stopped. Do not change
TC4CR<TFF4> upon stopping of the timer.
Example: Fixing the PPG4 pin to the high level when the TimerCounter is stopped
CLR (TC4CR).3: Stops the timer
CLR (TC4CR).7: Sets the PPG4 pin to the high level
Note 3: i = 3, 4
Page 127
Page 128
?
TTREG4
(Upper byte)
INTTC4 interrupt request
PPG4 pin
Timer F/F4
?
?
TTREG3
(Lower byte)
PWREG4
(Upper byte)
n
PWREG3
(Lower byte)
?
0
Counter
Internal
source clock
TC4CR<TFF4>
TC4CR<TC4S>
m
r
q
mn
Match detect
1
mn mn+1
Match detect
qr-1 qr 0
mn
Match detect
1
mn mn+1
Match detect
qr-1 qr 0
mn
Match detect
1
F/F clear
0
Held at the level when the timer
stops
mn mn+1
Write of "0"
11.1 Configuration
11. 8-Bit TimerCounter (TC3, TC4)
TMP86CH12MG
Figure 11-8 16-Bit PPG Mode Timing Chart (TC3 and TC40)
TMP86CH12MG
11.3.9 Warm-Up Counter Mode
In this mode, the warm-up period time is obtained to assure oscillation stability when the system clocking is
switched between the high-frequency and low-frequency. The timer counter 3 and 4 are cascadable to form a
16-bit TimerCouter. The warm-up counter mode has two types of mode; switching from the high-frequency to
low-frequency, and vice-versa.
Note 1: In the warm-up counter mode, fix TCiCR<TFFi> to 0. If not fixed, the PDOi, PWMi and PPGi pins may output
pulses.
Note 2: In the warm-up counter mode, only upper 8 bits of the timer register TTREG4 and 3 are used for match
detection and lower 8 bits are not used.
Note 3: i = 3, 4
11.3.9.1 Low-Frequency Warm-up Counter Mode
(NORMAL1 → NORMAL2 → SLOW2 → SLOW1)
In this mode, the warm-up period time from a stop of the low-frequency clock fs to oscillation stability
is obtained. Before starting the timer, set SYSCR2<XTEN> to 1 to oscillate the low-frequency clock.
When a match between the up-counter and the timer register (TTREG4, 3) value is detected after the timer
is started by setting TC4CR<TC4S> to 1, the counter is cleared by generating the INTTC4 interrupt
request. After stopping the timer in the INTTC4 interrupt service routine, set SYSCR2<SYSCK> to 1 to
switch the system clock from the high-frequency to low-frequency, and then clear of SYSCR2<XTEN> to
0 to stop the high-frequency clock.
Table 11-8 Setting Time of Low-Frequency Warm-Up Counter Mode (fs = 32.768 kHz)
Maximum Time Setting
(TTREG4, 3 = 0100H)
Maximum Time Setting
(TTREG4, 3 = FF00H)
7.81 ms
1.99 s
Example :After checking low-frequency clock oscillation stability with TC4 and 3, switching to the SLOW1 mode
(SYSCR2).6
: SYSCR2<XTEN> ← 1
LD
(TC3CR), 43H
: Sets TFF3=0, source clock fs, and 16-bit mode.
LD
(TC4CR), 05H
: Sets TFF4=0, and warm-up counter mode.
LD
(TTREG3), 8000H
: Sets the warm-up time.
(The warm-up time depends on the oscillator characteristic.)
SET
: IMF ← 0
DI
SET
(EIRH). 5
: IMF ← 1
EI
SET
:
PINTTC4:
: Enables the INTTC4.
(TC4CR).3
: Starts TC4 and 3.
:
CLR
(TC4CR).3
: Stops TC4 and 3.
SET
(SYSCR2).5
: SYSCR2<SYSCK> ← 1
(Switches the system clock to the low-frequency clock.)
CLR
(SYSCR2).7
: SYSCR2<XEN> ← 0 (Stops the high-frequency clock.)
RETI
:
VINTTC4:
DW
:
PINTTC4
: INTTC4 vector table
Page 129
11. 8-Bit TimerCounter (TC3, TC4)
11.1 Configuration
TMP86CH12MG
11.3.9.2 High-Frequency Warm-Up Counter Mode
(SLOW1 → SLOW2 → NORMAL2 → NORMAL1)
In this mode, the warm-up period time from a stop of the high-frequency clock fc to the oscillation stability is obtained. Before starting the timer, set SYSCR2<XEN> to 1 to oscillate the high-frequency clock.
When a match between the up-counter and the timer register (TTREG4, 3) value is detected after the timer
is started by setting TC4CR<TC4S> to 1, the counter is cleared by generating the INTTC4 interrupt
request. After stopping the timer in the INTTC4 interrupt service routine, clear SYSCR2<SYSCK> to 0 to
switch the system clock from the low-frequency to high-frequency, and then SYSCR2<XTEN> to 0 to
stop the low-frequency clock.
Table 11-9 Setting Time in High-Frequency Warm-Up Counter Mode
Minimum time (TTREG4, 3 = 0100H)
Maximum time (TTREG4, 3 = FF00H)
16 µs
4.08 ms
Example :After checking high-frequency clock oscillation stability with TC4 and 3, switching to the NORMAL1 mode
SET
(SYSCR2).7
: SYSCR2<XEN> ← 1
LD
(TC3CR), 63H
: Sets TFF3=0, source clock fs, and 16-bit mode.
LD
(TC4CR), 05H
: Sets TFF4=0, and warm-up counter mode.
LD
(TTREG3), 0F800H
: Sets the warm-up time.
(The warm-up time depends on the oscillator characteristic.)
: IMF ← 0
DI
SET
(EIRH). 5
: Enables the INTTC4.
(TC4CR).3
: Starts the TC4 and 3.
: IMF ← 1
EI
SET
:
PINTTC4:
:
CLR
(TC4CR).3
: Stops the TC4 and 3.
CLR
(SYSCR2).5
: SYSCR2<SYSCK> ← 0
(Switches the system clock to the high-frequency clock.)
CLR
(SYSCR2).6
: SYSCR2<XTEN> ← 0
(Stops the low-frequency clock.)
RETI
VINTTC4:
:
:
DW
PINTTC4
: INTTC4 vector table
Page 130
TMP86CH12MG
12. Synchronous Serial Interface (SIO)
The TMP86CH12MG has a clocked-synchronous 8-bit serial interface. Serial interface has an 8-byte transmit and
receive data buffer that can automatically and continuously transfer up to 64 bits of data.
Serial interface is connected to outside peripherl devices via SO, SI, SCK port.
12.1 Configuration
SIO control / status register
SIOSR
SIOCR1
SIOCR2
CPU
Transmit and
receive data buffer
(8 bytes in DBR)
Buffer control
circuit
Control circuit
Shift register
Shift
clock
7
6
5
4
3
2
1
0
SO
Serial data output
8-bit transfer
4-bit transfer
SI
Serial data input
INTSIO interrupt request
Serial clock
SCK
Serial clock I/O
Figure 12-1 Serial Interface
Page 131
12. Synchronous Serial Interface (SIO)
12.2 Control
TMP86CH12MG
12.2 Control
The serial interface is controlled by SIO control registers (SIOCR1/SIOCR2). The serial interface status can be
determined by reading SIO status register (SIOSR).
The transmit and receive data buffer is controlled by the SIOCR2<BUF>. The data buffer is assigned to address
0F80H to 0F87H for SIO in the DBR area, and can continuously transfer up to 8 words (bytes or nibbles) at one time.
When the specified number of words has been transferred, a buffer empty (in the transmit mode) or a buffer full (in
the receive mode or transmit/receive mode) interrupt (INTSIO) is generated.
When the internal clock is used as the serial clock in the 8-bit receive mode and the 8-bit transmit/receive mode, a
fixed interval wait can be applied to the serial clock for each word transferred. Four different wait times can be
selected with SIOCR2<WAIT>.
SIO Control Register 1
SIOCR1
7
6
(0031H)
SIOS
SIOINH
SIOS
5
4
Continue / abort transfer
SIOM
2
1
SIOM
Indicate transfer start / stop
SIOINH
3
Transfer mode select
0
SCK
0:
Stop
1:
Start
(Initial value: 0000 0000)
0:
Continuously transfer
1:
Abort transfer (Automatically cleared after abort)
000:
8-bit transmit mode
010:
4-bit transmit mode
100:
8-bit transmit / receive mode
101:
8-bit receive mode
110:
4-bit receive mode
Write
only
Except the above: Reserved
NORMAL1/2, IDLE1/2 mode
SCK
Serial clock select
DV7CK = 0
DV7CK = 1
SLOW1/2
SLEEP1/2
mode
000
fc/213
fs/25
fs/25
001
fc/28
fc/28
-
010
fc/27
fc/27
-
011
fc/26
fc/26
-
100
fc/25
fc/25
-
101
fc/24
fc/24
-
110
Reserved
111
External clock ( Input from SCK pin )
Note 1: fc; High-frequency clock [Hz], fs; Low-frequency clock [Hz]
Note 2: Set SIOS to "0" and SIOINH to "1" when setting the transfer mode or serial clock.
Note 3: SIOCR1 is write-only register, which cannot access any of in read-modify-write instruction such as bit operate, etc.
SIO Control Register 2
SIOCR2
(0032H)
7
6
5
4
3
WAIT
Page 132
2
1
BUF
0
(Initial value: ***0 0000)
Write
only
TMP86CH12MG
Always sets "00" except 8-bit transmit / receive mode.
WAIT
Wait control
Number of transfer words
(Buffer address in use)
BUF
00:
Tf = TD(Non wait)
01:
Tf = 2TD(Wait)
10:
Tf = 4TD(Wait)
11:
Tf = 8TD (Wait)
000:
1 word transfer
0F80H
001:
2 words transfer
0F80H ~ 0F81H
010:
3 words transfer
0F80H ~ 0F82H
011:
4 words transfer
0F80H ~ 0F83H
100:
5 words transfer
0F80H ~ 0F84H
101:
6 words transfer
0F80H ~ 0F85H
110:
7 words transfer
0F80H ~ 0F86H
111:
8 words transfer
0F80H ~ 0F87H
Write
only
Note 1: The lower 4 bits of each buffer are used during 4-bit transfers. Zeros (0) are stored to the upper 4bits when receiving.
Note 2: Transmitting starts at the lowest address. Received data are also stored starting from the lowest address to the highest
address. ( The first buffer address transmitted is 0F80H ).
Note 3: The value to be loaded to BUF is held after transfer is completed.
Note 4: SIOCR2 must be set when the serial interface is stopped (SIOF = 0).
Note 5: *: Don't care
Note 6: SIOCR2 is write-only register, which cannot access any of in read-modify-write instruction such as bit operate, etc.
SIO Status Register
SIOSR
7
6
(0032H)
SIOF
SEF
SIOF
SEF
5
4
3
2
1
Serial transfer operating status monitor
0:
1:
Transfer terminated
Transfer in process
Shift operating status monitor
0:
1:
Shift operation terminated
Shift operation in process
0
Note 1: Tf; Frame time, TD; Data transfer time
Note 2: After SIOS is cleared to "0", SIOF is cleared to "0" at the termination of transfer or the setting of SIOINH to "1".
(output)
SCK output
TD
Tf
Figure 12-2 Frame time (Tf) and Data transfer time (TD)
12.3 Serial clock
12.3.1 Clock source
Internal clock or external clock for the source clock is selected by SIOCR1<SCK>.
Page 133
Read
only
12. Synchronous Serial Interface (SIO)
12.3 Serial clock
TMP86CH12MG
12.3.1.1 Internal clock
Any of six frequencies can be selected. The serial clock is output to the outside on the SCK pin. The
SCK pin goes high when transfer starts.
When data writing (in the transmit mode) or reading (in the receive mode or the transmit/receive mode)
cannot keep up with the serial clock rate, there is a wait function that automatically stops the serial clock
and holds the next shift operation until the read/write processing is completed.
Table 12-1 Serial Clock Rate
NORMAL1/2, IDLE1/2 mode
DV7CK = 0
SLOW1/2,
SLEEP1/2 mode
DV7CK = 1
SCK
Clock
Baud Rate
Clock
Baud Rate
Clock
Baud Rate
000
fc/213
1.91 Kbps
fs/25
1024 bps
fs/25
1024 bps
001
fc/28
61.04 Kbps
fc/28
61.04 Kbps
-
-
010
fc/27
122.07 Kbps
fc/27
122.07 Kbps
-
-
011
fc/26
244.14 Kbps
fc/26
244.14 Kbps
-
-
100
fc/25
488.28 Kbps
fc/25
488.28 Kbps
-
-
101
fc/24
976.56 Kbps
fc/24
976.56 Kbps
-
-
110
-
-
-
-
-
-
111
External
External
External
External
External
External
Note: 1 Kbit = 1024 bit (fc = 16 MHz, fs = 32.768 kHz)
Automatically
wait function
SCK
pin (output)
SO
a0
pin (output)
Written transmit
data
a1
a2
a3
a
b0
b
b1
b2
b3
c0
c1
c
Figure 12-3 Automatic Wait Function (at 4-bit transmit mode)
12.3.1.2 External clock
An external clock connected to the SCK pin is used as the serial clock. In this case, output latch of this
port should be set to "1". To ensure shifting, a pulse width of at least 4 machine cycles is required. This
pulse is needed for the shift operation to execute certainly. Actually, there is necessary processing time for
interrupting, writing, and reading. The minimum pulse is determined by setting the mode and the program. Therfore, maximum transfer frequency will be 488.3K bit/sec (at fc=16MHz).
SCK
pin (Output)
tcyc = 4/fc (In the NORMAL1/2, IDLE1/2 modes)
4/fs (In the SLOW1/2, SLEEP1/2 modes)
tSCKL, tSCKH > 4tcyc
tSCKL tSCKH
Figure 12-4 External clock pulse width
Page 134
TMP86CH12MG
12.3.2 Shift edge
The leading edge is used to transmit, and the trailing edge is used to receive.
12.3.2.1 Leading edge
Transmitted data are shifted on the leading edge of the serial clock (falling edge of the SCK pin input/
output).
12.3.2.2 Trailing edge
Received data are shifted on the trailing edge of the serial clock (rising edge of the SCK pin input/output).
SCK pin
SO pin
Bit 0
Bit 1
Bit 2
Bit 3
Shift register
3210
*321
**32
***3
Bit 2
Bit 3
(a) Leading edge
SCK pin
SI pin
Shift register
Bit 0
Bit 1
0***
****
10**
210*
3210
*; Don’t care
(b) Trailing edge
Figure 12-5 Shift edge
12.4 Number of bits to transfer
Either 4-bit or 8-bit serial transfer can be selected. When 4-bit serial transfer is selected, only the lower 4 bits of
the transmit/receive data buffer register are used. The upper 4 bits are cleared to “0” when receiving.
The data is transferred in sequence starting at the least significant bit (LSB).
12.5 Number of words to transfer
Up to 8 words consisting of 4 bits of data (4-bit serial transfer) or 8 bits (8-bit serial transfer) of data can be transferred continuously. The number of words to be transferred can be selected by SIOCR2<BUF>.
An INTSIO interrupt is generated when the specified number of words has been transferred. If the number of
words is to be changed during transfer, the serial interface must be stopped before making the change. The number of
words can be changed during automatic-wait operation of an internal clock. In this case, the serial interface is not
required to be stopped.
Page 135
12. Synchronous Serial Interface (SIO)
12.6 Transfer Mode
TMP86CH12MG
SCK pin
SO pin
a0
a1
a2
a3
INTSIO interrupt
(a) 1 word transmit
SCK pin
SO pin
a0
a1
a2
a3
b0
b1
b2
b3
c0
c1
c2
c3
b3
c0
c1
c2
c3
INTSIO interrupt
(b) 3 words transmit
SCK pin
SI pin
a0
a1
a2
a3
b0
b1
b2
INTSIO interrupt
(c) 3 words receive
Figure 12-6 Number of words to transfer (Example: 1word = 4bit)
12.6 Transfer Mode
SIOCR1<SIOM> is used to select the transmit, receive, or transmit/receive mode.
12.6.1 4-bit and 8-bit transfer modes
In these modes, firstly set the SIO control register to the transmit mode, and then write first transmit data
(number of transfer words to be transferred) to the data buffer registers (DBR).
After the data are written, the transmission is started by setting SIOCR1<SIOS> to “1”. The data are then
output sequentially to the SO pin in synchronous with the serial clock, starting with the least significant bit
(LSB). As soon as the LSB has been output, the data are transferred from the data buffer register to the shift
register. When the final data bit has been transferred and the data buffer register is empty, an INTSIO (Buffer
empty) interrupt is generated to request the next transmitted data.
When the internal clock is used, the serial clock will stop and an automatic-wait will be initiated if the next
transmitted data are not loaded to the data buffer register by the time the number of data words specified with
the SIOCR2<BUF> has been transmitted. Writing even one word of data cancels the automatic-wait; therefore,
when transmitting two or more words, always write the next word before transmission of the previous word is
completed.
Note:Automatic waits are also canceled by writing to a DBR not being used as a transmit data buffer register; therefore, during SIO do not use such DBR for other applications. For example, when 3 words are transmitted, do
not use the DBR of the remained 5 words.
When an external clock is used, the data must be written to the data buffer register before shifting next data.
Thus, the transfer speed is determined by the maximum delay time from the generation of the interrupt request
to writing of the data to the data buffer register by the interrupt service program.
The transmission is ended by clearing SIOCR1<SIOS> to “0” or setting SIOCR1<SIOINH> to “1” in buffer
empty interrupt service program.
Page 136
TMP86CH12MG
SIOCR1<SIOS> is cleared, the operation will end after all bits of words are transmitted.
That the transmission has ended can be determined from the status of SIOSR<SIOF> because SIOSR<SIOF>
is cleared to “0” when a transfer is completed.
When SIOCR1<SIOINH> is set, the transmission is immediately ended and SIOSR<SIOF> is cleared to
“0”.
When an external clock is used, it is also necessary to clear SIOCR1<SIOS> to “0” before shifting the next
data; If SIOCR1<SIOS> is not cleared before shift out, dummy data will be transmitted and the operation will
end.
If it is necessary to change the number of words, SIOCR1<SIOS> should be cleared to “0”, then
SIOCR2<BUF> must be rewritten after confirming that SIOSR<SIOF> has been cleared to “0”.
Clear SIOS
SIOCR1<SIOS>
SIOSR<SIOF>
SIOSR<SEF>
SCK pin
(Output)
SO pin
a0
a1
a2
a3
a4
a5
a6
a7
b0
b1
b2
b3
b4
b5
b6
b7
INTSIO interrupt
a
DBR
b
Write Write
(a)
(b)
Figure 12-7 Transfer Mode (Example: 8bit, 1word transfer, Internal clock)
Clear SIOS
SIOCR1<SIOS>
SIOSR<SIOF>
SIOSR<SEF>
SCK pin
(Input)
SO pin
a0
a1
a2
a3
a4
a5
a6
a7
b0
b1
b2
b3
b4
b5
b6
b7
INTSIO interrupt
DBR
a
b
Write Write
(a)
(b)
Figure 12-8 Transfer Mode (Example: 8bit, 1word transfer, External clock)
Page 137
12. Synchronous Serial Interface (SIO)
12.6 Transfer Mode
TMP86CH12MG
SCK pin
SIOSR<SIOF>
SO pin
MSB of last word
tSODH = min 3.5/fc [s] ( In the NORMAL1/2, IDLE1/2 modes)
tSODH = min 3.5/fs [s] (In the SLOW1/2, SLEEP1/2 modes)
Figure 12-9 Transmiiied Data Hold Time at End of Transfer
12.6.2 4-bit and 8-bit receive modes
After setting the control registers to the receive mode, set SIOCR1<SIOS> to “1” to enable receiving. The
data are then transferred to the shift register via the SI pin in synchronous with the serial clock. When one word
of data has been received, it is transferred from the shift register to the data buffer register (DBR). When the
number of words specified with the SIOCR2<BUF> has been received, an INTSIO (Buffer full) interrupt is
generated to request that these data be read out. The data are then read from the data buffer registers by the
interrupt service program.
When the internal clock is used, and the previous data are not read from the data buffer register before the
next data are received, the serial clock will stop and an automatic-wait will be initiated until the data are read.
A wait will not be initiated if even one data word has been read.
Note:Waits are also canceled by reading a DBR not being used as a received data buffer register is read; therefore,
during SIO do not use such DBR for other applications.
When an external clock is used, the shift operation is synchronized with the external clock; therefore, the
previous data are read before the next data are transferred to the data buffer register. If the previous data have
not been read, the next data will not be transferred to the data buffer register and the receiving of any more data
will be canceled. When an external clock is used, the maximum transfer speed is determined by the delay
between the time when the interrupt request is generated and when the data received have been read.
The receiving is ended by clearing SIOCR1<SIOS> to “0” or setting SIOCR1<SIOINH> to “1” in buffer full
interrupt service program.
When SIOCR1<SIOS> is cleared, the current data are transferred to the buffer. After SIOCR1<SIOS>
cleared, the receiving is ended at the time that the final bit of the data has been received. That the receiving has
ended can be determined from the status of SIOSR<SIOF>. SIOSR<SIOF> is cleared to “0” when the receiving is ended. After confirmed the receiving termination, the final receiving data is read. When SIOCR1<SIOINH> is set, the receiving is immediately ended and SIOSR<SIOF> is cleared to “0”. (The received data is
ignored, and it is not required to be read out.)
If it is necessary to change the number of words in external clock operation, SIOCR1<SIOS> should be
cleared to “0” then SIOCR2<BUF> must be rewritten after confirming that SIOSR<SIOF> has been cleared to
“0”. If it is necessary to change the number of words in internal clock, during automatic-wait operation which
occurs after completion of data receiving, SIOCR2<BUF> must be rewritten before the received data is read
out.
Note:The buffer contents are lost when the transfer mode is switched. If it should become necessary to switch the
transfer mode, end receiving by clearing SIOCR1<SIOS> to “0”, read the last data and then switch the transfer mode.
Page 138
TMP86CH12MG
Clear SIOS
SIOCR1<SIOS>
SIOSR<SIOF>
SIOSR<SEF>
SCK pin
(Output)
SI pin
a0
a1
a2
a3
a4
a5
a6
a7
b0
b1
b2
b3
b4
b5
b6
b7
INTSIO Interrupt
DBR
a
b
Read out
Read out
Figure 12-10 Receive Mode (Example: 8bit, 1word transfer, Internal clock)
12.6.3 8-bit transfer / receive mode
After setting the SIO control register to the 8-bit transmit/receive mode, write the data to be transmitted first
to the data buffer registers (DBR). After that, enable the transmit/receive by setting SIOCR1<SIOS> to “1”.
When transmitting, the data are output from the SO pin at leading edges of the serial clock. When receiving,
the data are input to the SI pin at the trailing edges of the serial clock. When the all receive is enabled, 8-bit
data are transferred from the shift register to the data buffer register. An INTSIO interrupt is generated when
the number of data words specified with the SIOCR2<BUF> has been transferred. Usually, read the receive
data from the buffer register in the interrupt service. The data buffer register is used for both transmitting and
receiving; therefore, always write the data to be transmitted after reading the all received data.
When the internal clock is used, a wait is initiated until the received data are read and the next transfer data
are written. A wait will not be initiated if even one transfer data word has been written.
When an external clock is used, the shift operation is synchronized with the external clock; therefore, it is
necessary to read the received data and write the data to be transmitted next before starting the next shift operation. When an external clock is used, the transfer speed is determined by the maximum delay between generation of an interrupt request and the received data are read and the data to be transmitted next are written.
The transmit/receive operation is ended by clearing SIOCR1<SIOS> to “0” or setting SIOCR1<SIOINH> to
“1” in INTSIO interrupt service program.
When SIOCR1<SIOS> is cleared, the current data are transferred to the buffer. After SIOCR1<SIOS>
cleared, the transmitting/receiving is ended at the time that the final bit of the data has been transmitted.
That the transmitting/receiving has ended can be determined from the status of SIOSR<SIOF>.
SIOSR<SIOF> is cleared to “0” when the transmitting/receiving is ended.
When SIOCR1<SIOINH> is set, the transmit/receive operation is immediately ended and SIOSR<SIOF> is
cleared to “0”.
If it is necessary to change the number of words in external clock operation, SIOCR1<SIOS> should be
cleared to “0”, then SIOCR2<BUF> must be rewritten after confirming that SIOSR<SIOF> has been cleared to
“0”.
If it is necessary to change the number of words in internal clock, during automatic-wait operation which
occurs after completion of transmit/receive operation, SIOCR2<BUF> must be rewritten before reading and
writing of the receive/transmit data.
Page 139
12. Synchronous Serial Interface (SIO)
12.6 Transfer Mode
TMP86CH12MG
Note:The buffer contents are lost when the transfer mode is switched. If it should become necessary to switch the
transfer mode, end receiving by clearing SIOCR1<SIOS> to “0”, read the last data and then switch the transfer mode.
Clear SIOS
SIOCR1<SIOS>
SIOSR<SIOF>
SIOSR<SEF>
SCK pin
(output)
SO pin
a0
a1
a2
a3
a4
a5
a6
a7
b0
b1
b2
b3
b4
b5
b6
b7
SI pin
c0
c1
c2
c3
c4
c5
c6
c7
d0
d1
d2
d3
d4
d5
d6
d7
INTSIO interrupt
c
a
DBR
Write (a)
Read out (c)
b
Write (b)
d
Read out (d)
Figure 12-11 Transfer / Receive Mode (Example: 8bit, 1word transfer, Internal clock)
SCK pin
SIOSR<SIOF>
SO pin
Bit 6
Bit 7 of last word
tSODH = min 4/fc [s] ( In the NORMAL1/2, IDLE1/2 modes)
tSODH = min 4/fs [s] (In the SLOW1/2, SLEEP1/2 modes)
Figure 12-12 Transmitted Data Hold Time at End of Transfer / Receive
Page 140
TMP86CH12MG
13. Asynchronous Serial interface (UART )
13.1 Configuration
UART control register 1
Transmit data buffer
UARTCR1
TDBUF
3
Receive data buffer
RDBUF
2
INTTXD
Receive control circuit
Transmit control circuit
2
Shift register
Shift register
Parity bit
Stop bit
Noise rejection
circuit
RXD
TXD
INTRXD
Transmit/receive clock
Y
M
P
X
S
fc/13
fc/26
fc/52
fc/104
fc/208
fc/416
INTTC3
fc/96
A
B
C
D
E
F
G
H
A
B
C
fc/26
fc/27
8
fc/2
S
2
Y
4
2
Counter
UARTSR
UARTCR2
UART status register
UART control register 2
MPX: Multiplexer
Baud rate generator
Figure 13-1 UART (Asynchronous Serial Interface)
Page 141
13. Asynchronous Serial interface (UART )
13.2 Control
TMP86CH12MG
13.2 Control
UART is controlled by the UART Control Registers (UARTCR1, UARTCR2). The operating status can be monitored using the UART status register (UARTSR).
UART Control Register1
UARTCR1
(0021H)
7
6
5
4
3
TXE
RXE
STBT
EVEN
PE
2
1
0
BRG
(Initial value: 0000 0000)
TXE
Transfer operation
0:
1:
Disable
Enable
RXE
Receive operation
0:
1:
Disable
Enable
STBT
Transmit stop bit length
0:
1:
1 bit
2 bits
EVEN
Even-numbered parity
0:
1:
Odd-numbered parity
Even-numbered parity
Parity addition
0:
1:
No parity
Parity
PE
BRG
000:
001:
010:
011:
100:
101:
110:
111:
Transmit clock select
Write
only
fc/13 [Hz]
fc/26
fc/52
fc/104
fc/208
fc/416
TC3 ( Input INTTC3)
fc/96
Note 1: When operations are disabled by setting TXE and RXE bit to “0”, the setting becomes valid when data transmit or receive
complete. When the transmit data is stored in the transmit data buffer, the data are not transmitted. Even if data transmit is
enabled, until new data are written to the transmit data buffer, the current data are not transmitted.
Note 2: The transmit clock and the parity are common to transmit and receive.
Note 3: UARTCR1<RXE> and UARTCR1<TXE> should be set to “0” before UARTCR1<BRG> is changed.
UART Control Register2
UARTCR2
(0022H)
7
6
5
4
3
2
1
0
RXDNC
RXDNC
Selection of RXD input noise
rejectio time
STOPBR
Receive stop bit length
00:
01:
10:
11:
0:
1:
STOPBR
(Initial value: **** *000)
No noise rejection (Hysteresis input)
Rejects pulses shorter than 31/fc [s] as noise
Rejects pulses shorter than 63/fc [s] as noise
Rejects pulses shorter than 127/fc [s] as noise
Write
only
1 bit
2 bits
Note: When UARTCR2<RXDNC> = “01”, pulses longer than 96/fc [s] are always regarded as signals; when UARTCR2<RXDNC>
= “10”, longer than 192/fc [s]; and when UARTCR2<RXDNC> = “11”, longer than 384/fc [s].
Page 142
TMP86CH12MG
UART Status Register
UARTSR
(0021H)
7
6
5
4
3
2
1
PERR
FERR
OERR
RBFL
TEND
TBEP
0
(Initial value: 0000 11**)
PERR
Parity error flag
0:
1:
No parity error
Parity error
FERR
Framing error flag
0:
1:
No framing error
Framing error
OERR
Overrun error flag
0:
1:
No overrun error
Overrun error
RBFL
Receive data buffer full flag
0:
1:
Receive data buffer empty
Receive data buffer full
TEND
Transmit end flag
0:
1:
On transmitting
Transmit end
TBEP
Transmit data buffer empty flag
0:
1:
Transmit data buffer full (Transmit data writing is finished)
Transmit data buffer empty
Note: When an INTTXD is generated, TBEP flag is set to "1" automatically.
UART Receive Data Buffer
RDBUF
(0F89H)
7
6
5
4
3
2
1
0
Read only
(Initial value: 0000 0000)
UART Transmit Data Buffer
TDBUF
(0F89H)
7
6
5
4
3
2
1
0
Write only
(Initial value: 0000 0000)
Page 143
Read
only
13. Asynchronous Serial interface (UART )
13.3 Transfer Data Format
TMP86CH12MG
13.3 Transfer Data Format
In UART, an one-bit start bit (Low level), stop bit (Bit length selectable at high level, by UARTCR1<STBT>), and
parity (Select parity in UARTCR1<PE>; even- or odd-numbered parity by UARTCR1<EVEN>) are added to the
transfer data. The transfer data formats are shown as follows.
PE
STBT
0
Frame Length
8
1
2
3
9
10
0
Start
Bit 0
Bit 1
0
1
Start
Bit 0
1
0
Start
1
1
Start
11
Bit 6
Bit 7
Stop 1
Bit 1
Bit 6
Bit 7
Stop 1
Stop 2
Bit 0
Bit 1
Bit 6
Bit 7
Parity
Stop 1
Bit 0
Bit 1
Bit 6
Bit 7
Parity
Stop 1
12
Stop 2
Figure 13-2 Transfer Data Format
Without parity / 1 STOP bit
With parity / 1 STOP bit
Without parity / 2 STOP bit
With parity / 2 STOP bit
Figure 13-3 Caution on Changing Transfer Data Format
Note: In order to switch the transfer data format, perform transmit operations in the above Figure 13-3 sequence except
for the initial setting.
Page 144
TMP86CH12MG
13.4 Transfer Rate
The baud rate of UART is set of UARTCR1<BRG>. The example of the baud rate are shown as follows.
Table 13-1 Transfer Rate (Example)
Source Clock
BRG
16 MHz
8 MHz
4 MHz
000
76800 [baud]
38400 [baud]
19200 [baud]
001
38400
19200
9600
010
19200
9600
4800
011
9600
4800
2400
100
4800
2400
1200
101
2400
1200
600
When TC3 is used as the UART transfer rate (when UARTCR1<BRG> = “110”), the transfer clock and transfer
rate are determined as follows:
Transfer clock [Hz] = TC3 source clock [Hz] / TTREG3 setting value
Transfer Rate [baud] = Transfer clock [Hz] / 16
13.5 Data Sampling Method
The UART receiver keeps sampling input using the clock selected by UARTCR1<BRG> until a start bit is
detected in RXD pin input. RT clock starts detecting “L” level of the RXD pin. Once a start bit is detected, the start
bit, data bits, stop bit(s), and parity bit are sampled at three times of RT7, RT8, and RT9 during one receiver clock
interval (RT clock). (RT0 is the position where the bit supposedly starts.) Bit is determined according to majority
rule (The data are the same twice or more out of three samplings).
RXD pin
Start bit
RT0
1
2
3
Bit 0
4
5
6
7
8
9 10 11 12 13 14 15 0
1
2
3
4
5
6
7
8
9 10 11
2
3
4
5
6
7
8
9 10 11
RT clock
Start bit
Internal receive data
Bit 0
(a) Without noise rejection circuit
RXD pin
Start bit
RT0
1
2
3
Bit 0
4
5
6
7
8
9 10 11 12 13 14 15 0
1
RT clock
Internal receive data
Start bit
Bit 0
(b) With noise rejection circuit
Figure 13-4 Data Sampling Method
Page 145
13. Asynchronous Serial interface (UART )
13.6 STOP Bit Length
TMP86CH12MG
13.6 STOP Bit Length
Select a transmit stop bit length (1 bit or 2 bits) by UARTCR1<STBT>.
13.7 Parity
Set parity / no parity by UARTCR1<PE> and set parity type (Odd- or Even-numbered) by UARTCR1<EVEN>.
13.8 Transmit/Receive Operation
13.8.1 Data Transmit Operation
Set UARTCR1<TXE> to “1”. Read UARTSR to check UARTSR<TBEP> = “1”, then write data in TDBUF
(Transmit data buffer). Writing data in TDBUF zero-clears UARTSR<TBEP>, transfers the data to the transmit
shift register and the data are sequentially output from the TXD pin. The data output include a one-bit start bit,
stop bits whose number is specified in UARTCR1<STBT> and a parity bit if parity addition is specified.
Select the data transfer baud rate using UARTCR1<BRG>. When data transmit starts, transmit buffer empty
flag UARTSR<TBEP> is set to “1” and an INTTXD interrupt is generated.
While UARTCR1<TXE> = “0” and from when “1” is written to UARTCR1<TXE> to when send data are
written to TDBUF, the TXD pin is fixed at high level.
When transmitting data, first read UARTSR, then write data in TDBUF. Otherwise, UARTSR<TBEP> is not
zero-cleared and transmit does not start.
13.8.2 Data Receive Operation
Set UARTCR1<RXE> to “1”. When data are received via the RXD pin, the receive data are transferred to
RDBUF (Receive data buffer). At this time, the data transmitted includes a start bit and stop bit(s) and a parity
bit if parity addition is specified. When stop bit(s) are received, data only are extracted and transferred to
RDBUF (Receive data buffer). Then the receive buffer full flag UARTSR<RBFL> is set and an INTRXD
interrupt is generated. Select the data transfer baud rate using UARTCR1<BRG>.
If an overrun error (OERR) occurs when data are received, the data are not transferred to RDBUF (Receive
data buffer) but discarded; data in the RDBUF are not affected.
Note:When a receive operation is disabled by setting UARTCR1<RXE> bit to “0”, the setting becomes valid when
data receive is completed. However, if a framing error occurs in data receive, the receive-disabling setting
may not become valid. If a framing error occurs, be sure to perform a re-receive operation.
Page 146
TMP86CH12MG
13.9 Status Flag
13.9.1 Parity Error
When parity determined using the receive data bits differs from the received parity bit, the parity error flag
UARTSR<PERR> is set to “1”. The UARTSR<PERR> is cleared to “0” when the RDBUF is read after reading the UARTSR.
RXD pin
Shift register
Parity
Stop
pxxxx0*
xxxx0**
1pxxxx0
UARTSR<PERR>
After reading UARTSR then
RDBUF clears PERR.
INTRXD interrupt
Figure 13-5 Generation of Parity Error
13.9.2 Framing Error
When “0” is sampled as the stop bit in the receive data, framing error flag UARTSR<FERR> is set to “1”.
The UARTSR<FERR> is cleared to “0” when the RDBUF is read after reading the UARTSR.
RXD pin
Shift register
Stop
Final bit
xxxx0*
xxx0**
0xxxx0
After reading UARTSR then
RDBUF clears FERR.
UARTSR<FERR>
INTRXD interrupt
Figure 13-6 Generation of Framing Error
13.9.3 Overrun Error
When all bits in the next data are received while unread data are still in RDBUF, overrun error flag
UARTSR<OERR> is set to “1”. In this case, the receive data is discarded; data in RDBUF are not affected.
The UARTSR<OERR> is cleared to “0” when the RDBUF is read after reading the UARTSR.
Page 147
13. Asynchronous Serial interface (UART )
13.9 Status Flag
TMP86CH12MG
UARTSR<RBFL>
RXD pin
Stop
Final bit
Shift register
xxx0**
RDBUF
yyyy
xxxx0*
1xxxx0
UARTSR<OERR>
After reading UARTSR then
RDBUF clears OERR.
INTRXD interrupt
Figure 13-7 Generation of Overrun Error
Note:Receive operations are disabled until the overrun error flag UARTSR<OERR> is cleared.
13.9.4 Receive Data Buffer Full
Loading the received data in RDBUF sets receive data buffer full flag UARTSR<RBFL> to "1". The
UARTSR<RBFL> is cleared to “0” when the RDBUF is read after reading the UARTSR.
RXD pin
Stop
Final bit
Shift register
xxx0**
RDBUF
yyyy
xxxx0*
1xxxx0
xxxx
After reading UARTSR then
RDBUF clears RBFL.
UARTSR<RBFL>
INTRXD interrupt
Figure 13-8 Generation of Receive Data Buffer Full
Note:If the overrun error flag UARTSR<OERR> is set during the period between reading the UARTSR and reading
the RDBUF, it cannot be cleared by only reading the RDBUF. Therefore, after reading the RDBUF, read the
UARTSR again to check whether or not the overrun error flag which should have been cleared still remains
set.
13.9.5 Transmit Data Buffer Empty
When no data is in the transmit buffer TDBUF, UARTSR<TBEP> is set to “1”, that is, when data in TDBUF
are transferred to the transmit shift register and data transmit starts, transmit data buffer empty flag
UARTSR<TBEP> is set to “1”. The UARTSR<TBEP> is cleared to “0” when the TDBUF is written after
reading the UARTSR.
Page 148
TMP86CH12MG
Data write
TDBUF
xxxx
*****1
Shift register
TXD pin
Data write
zzzz
yyyy
1xxxx0
*1xxxx
****1x
*****1
Start
Bit 0
Final bit
Stop
1yyyy0
UARTSR<TBEP>
After reading UARTSR writing TDBUF
clears TBEP.
INTTXD interrupt
Figure 13-9 Generation of Transmit Data Buffer Empty
13.9.6 Transmit End Flag
When data are transmitted and no data is in TDBUF (UARTSR<TBEP> = “1”), transmit end flag
UARTSR<TEND> is set to “1”. The UARTSR<TEND> is cleared to “0” when the data transmit is stated after
writing the TDBUF.
Shift register
TXD pin
***1xx
****1x
*****1
1yyyy0
Stop
Start
*1yyyy
Bit 0
Data write for TDBUF
UARTSR<TBEP>
UARTSR<TEND>
INTTXD interrupt
Figure 13-10 Generation of Transmit End Flag and Transmit Data Buffer Empty
Page 149
13. Asynchronous Serial interface (UART )
13.9 Status Flag
TMP86CH12MG
Page 150
TMP86CH12MG
14. 10-bit AD Converter (ADC)
The TMP86CH12MG have a 10-bit successive approximation type AD converter.
14.1 Configuration
The circuit configuration of the 10-bit AD converter is shown in Figure 14-1.
It consists of control register ADCCR1 and ADCCR2, converted value register ADCDR1 and ADCDR2, a DA
converter, a sample-hold circuit, a comparator, and a successive comparison circuit.
DA converter
VDD
VSS
R/2
Analog input
multiplexer
AIN0
A
R
R/2
Sample hold
circuit
Reference
voltage
Y
10
Analog
comparator
n
S EN
Successive approximate circuit
Shift clock
AINDS
ADRS
SAIN
INTADC
Control circuit
4
ADCCR1
2
AMD
IREFON
AIN7
3
ACK
ADCCR2
AD converter control register 1, 2
8
ADCDR1
2
EOCF ADBF
ADCDR2
AD conversion result register 1, 2
Note: Before using AD converter, set appropriate value to I/O port register conbining a analog input port. For details, see the section on "I/O ports".
Figure 14-1 10-bit AD Converter
Page 151
14. 10-bit AD Converter (ADC)
14.2 Register configuration
TMP86CH12MG
14.2 Register configuration
The AD converter consists of the following four registers:
1. AD converter control register 1 (ADCCR1)
This register selects the analog channels and operation mode (Software start or repeat) in which to perform AD conversion and controls the AD converter as it starts operating.
2. AD converter control register 2 (ADCCR2)
This register selects the AD conversion time and controls the connection of the DA converter (Ladder
resistor network).
3. AD converted value register 1 (ADCDR1)
This register used to store the digital value fter being converted by the AD converter.
4. AD converted value register 2 (ADCDR2)
This register monitors the operating status of the AD converter.
AD Converter Control Register 1
ADCCR1
(0025H)
7
ADRS
6
5
AMD
4
3
2
AINDS
1
SAIN
AD conversion start
0:
1:
AD conversion start
AMD
AD operating mode
00:
01:
10:
11:
AD operation disable
Software start mode
Reserved
Repeat mode
AINDS
Analog input control
0:
1:
Analog input enable
Analog input disable
Analog input channel select
0000:
0001:
0010:
0011:
0100:
0101:
0110:
0111:
1000:
1001:
1010:
1011:
1100:
1101:
1110:
1111:
AIN0
AIN1
AIN2
AIN3
AIN4
AIN5
AIN6
AIN7
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
ADRS
SAIN
0
(Initial value: 0001 0000)
R/W
Note 1: Select analog input channel during AD converter stops (ADCDR2<ADBF> = "0").
Note 2: When the analog input channel is all use disabling, the ADCCR1<AINDS> should be set to "1".
Note 3: During conversion, Do not perform port output instruction to maintain a precision for all of the pins because analog input
port use as general input port. And for port near to analog input, Do not input intense signaling of change.
Note 4: The ADCCR1<ADRS> is automatically cleared to "0" after starting conversion.
Note 5: Do not set ADCCR1<ADRS> newly again during AD conversion. Before setting ADCCR1<ADRS> newly again, check
ADCDR2<EOCF> to see that the conversion is completed or wait until the interrupt signal (INTADC) is generated (e.g.,
interrupt handling routine).
Note 6: After STOP or SLOW/SLEEP mode are started, AD converter control register1 (ADCCR1) is all initialized and no data can
be written in this register. Therfore, to use AD converter again, set the ADCCR1 newly after returning to NORMAL1 or
NORMAL2 mode.
Page 152
TMP86CH12MG
AD Converter Control Register 2
7
ADCCR2
(0026H)
6
IREFON
ACK
5
4
3
IREFON
"1"
2
1
ACK
0
"0"
(Initial value: **0* 000*)
DA converter (Ladder resistor) connection
control
0:
1:
Connected only during AD conversion
Always connected
AD conversion time select
(Refer to the following table about the conversion time)
000:
001:
010:
011:
100:
101:
110:
111:
39/fc
Reserved
78/fc
156/fc
312/fc
624/fc
1248/fc
Reserved
R/W
Note 1: Always set bit0 in ADCCR2 to "0" and set bit4 in ADCCR2 to "1".
Note 2: When a read instruction for ADCCR2, bit6 to 7 in ADCCR2 read in as undefined data.
Note 3: After STOP or SLOW/SLEEP mode are started, AD converter control register2 (ADCCR2) is all initialized and no data can
be written in this register. Therfore, to use AD converter again, set the ADCCR2 newly after returning to NORMAL1 or
NORMAL2 mode.
Table 14-1 ACK setting and Conversion time
Condition
ACK
000
Conversion
time
16 MHz
8 MHz
4 MHz
2 MHz
10 MHz
5 MHz
2.5 MHz
39/fc
-
-
-
19.5 µs
-
-
15.6 µs
001
Reserved
010
78/fc
-
-
19.5 µs
39.0 µs
-
15.6 µs
31.2 µs
011
156/fc
-
19.5 µs
39.0 µs
78.0 µs
15.6 µs
31.2 µs
62.4 µs
100
312/fc
19.5 µs
39.0 µs
78.0 µs
156.0 µs
31.2 µs
62.4 µs
124.8 µs
101
624/fc
39.0 µs
78.0 µs
156.0 µs
-
62.4 µs
124.8 µs
-
110
1248/fc
78.0 µs
156.0 µs
-
-
124.8 µs
-
-
111
Reserved
Note 1: Setting for "−" in the above table are inhibited.
fc: High Frequency oscillation clock [Hz]
Note 2: Set conversion time setting should be kept more than the following time by Power supply voltage(VDD) .
-
VDD = 4.5 to 5.5 V
15.6 µs and more
-
VDD = 2.7 to 5.5 V
31.2 µs and more
AD Converted value Register 1
ADCDR1
(0020H)
7
6
5
4
3
2
1
0
AD09
AD08
AD07
AD06
AD05
AD04
AD03
AD02
3
2
1
0
(Initial value: 0000 0000)
AD Converted value Register 2
ADCDR2
(001FH)
7
6
5
4
AD01
AD00
EOCF
ADBF
(Initial value: 0000 ****)
Page 153
14. 10-bit AD Converter (ADC)
14.2 Register configuration
TMP86CH12MG
EOCF
ADBF
AD conversion end flag
0:
1:
Before or during conversion
Conversion completed
AD conversion BUSY flag
0:
1:
During stop of AD conversion
During AD conversion
Read
only
Note 1: The ADCDR2<EOCF> is cleared to "0" when reading the ADCDR1. Therfore, the AD conversion result should be read to
ADCDR2 more first than ADCDR1.
Note 2: The ADCDR2<ADBF> is set to "1" when AD conversion starts, and cleared to "0" when AD conversion finished. It also is
cleared upon entering STOP mode or SLOW mode .
Note 3: If a read instruction is executed for ADCDR2, read data of bit3 to bit0 are unstable.
Page 154
TMP86CH12MG
14.3 Function
14.3.1 Software Start Mode
After setting ADCCR1<AMD> to “01” (software start mode), set ADCCR1<ADRS> to “1”. AD conversion of the voltage at the analog input pin specified by ADCCR1<SAIN> is thereby started.
After completion of the AD conversion, the conversion result is stored in AD converted value registers
(ADCDR1, ADCDR2) and at the same time ADCDR2<EOCF> is set to 1, the AD conversion finished interrupt (INTADC) is generated.
ADRS is automatically cleared after AD conversion has started. Do not set ADCCR1<ADRS> newly again
(Restart) during AD conversion. Before setting ADRS newly again, check ADCDR2<EOCF> to see that the
conversion is completed or wait until the interrupt signal (INTADC) is generated (e.g., interrupt handling routine).
AD conversion start
AD conversion start
ADCCR1<ADRS>
ADCDR2<ADBF>
ADCDR1 status
Indeterminate
1st conversion result
2nd conversion result
EOCF cleared by reading
conversion result
ADCDR2<EOCF>
INTADC interrupt request
ADCDR1
ADCDR2
Conversion result
read
Conversion result
read
Conversion result
read
Conversion result
read
Figure 14-2 Software Start Mode
14.3.2 Repeat Mode
AD conversion of the voltage at the analog input pin specified by ADCCR1<SAIN> is performed repeatedly.
In this mode, AD conversion is started by setting ADCCR1<ADRS> to “1” after setting ADCCR1<AMD> to
“11” (Repeat mode).
After completion of the AD conversion, the conversion result is stored in AD converted value registers
(ADCDR1, ADCDR2) and at the same time ADCDR2<EOCF> is set to 1, the AD conversion finished interrupt (INTADC) is generated.
In repeat mode, each time one AD conversion is completed, the next AD conversion is started. To stop AD
conversion, set ADCCR1<AMD> to “00” (Disable mode) by writing 0s. The AD convert operation is stopped
immediately. The converted value at this time is not stored in the AD converted value register.
Page 155
14. 10-bit AD Converter (ADC)
14.3 Function
TMP86CH12MG
ADCCR1<AMD>
“11”
“00”
AD conversion start
ADCCR1<ADRS>
1st conversion
result
Conversion operation
Indeterminate
ADCDR1,ADCDR2
2nd conversion result
3rd conversion result
1st conversion result
2nd conversion result
AD convert operation suspended.
Conversion result is not stored.
3rd conversion result
ADCDR2<EOCF>
EOCF cleared by reading
conversion result
INTADC interrupt request
ADCDR1
Conversion
result read
ADCDR2
Conversion
result read
Conversion
result read
Conversion
result read
Conversion
result read
Conversion
result read
Figure 14-3 Repeat Mode
14.3.3
Register Setting
1. Set up the AD converter control register 1 (ADCCR1) as follows:
• Choose the channel to AD convert using AD input channel select (SAIN).
• Specify analog input enable for analog input control (AINDS).
• Specify AMD for the AD converter control operation mode (software or repeat mode).
2. Set up the AD converter control register 2 (ADCCR2) as follows:
• Set the AD conversion time using AD conversion time (ACK). For details on how to set the conversion time, refer to Figure 14-1 and AD converter control register 2.
• Choose IREFON for DA converter control.
3. After setting up (1) and (2) above, set AD conversion start (ADRS) of AD converter control register 1
(ADCCR1) to “1”. If software start mode has been selected, AD conversion starts immediately.
4. After an elapse of the specified AD conversion time, the AD converted value is stored in AD converted value register 1 (ADCDR1) and the AD conversion finished flag (EOCF) of AD converted
value register 2 (ADCDR2) is set to “1”, upon which time AD conversion interrupt INTADC is generated.
5. EOCF is cleared to “0” by a read of the conversion result. However, if reconverted before a register
read, although EOCF is cleared the previous conversion result is retained until the next conversion is
completed.
Page 156
TMP86CH12MG
Example :After selecting the conversion time 19.5 µs at 16 MHz and the analog input channel AIN3 pin, perform AD conversion once. After checking EOCF, read the converted value, store the lower 2 bits in address 0009EH nd store
the upper 8 bits in address 0009FH in RAM. The operation mode is software start mode.
SLOOP :
: (port setting)
:
;Set port register approrriately before setting AD
converter registers.
:
:
(Refer to section I/O port in details)
LD
(ADCCR1) , 00100011B
; Select AIN3
LD
(ADCCR2) , 11011000B
;Select conversion time(312/fc) and operation
mode
SET
(ADCCR1) . 7
; ADRS = 1(AD conversion start)
TEST
(ADCDR2) . 5
; EOCF= 1 ?
JRS
T, SLOOP
LD
A , (ADCDR2)
LD
(9EH) , A
LD
A , (ADCDR1)
LD
(9FH), A
; Read result data
; Read result data
14.4 STOP/SLOW Modes during AD Conversion
When standby mode (STOP or SLOW mode) is entered forcibly during AD conversion, the AD convert operation
is suspended and the AD converter is initialized (ADCCR1 and ADCCR2 are initialized to initial value). Also, the
conversion result is indeterminate. (Conversion results up to the previous operation are cleared, so be sure to read
the conversion results before entering standby mode (STOP or SLOW mode).) When restored from standby mode
(STOP or SLOW mode), AD conversion is not automatically restarted, so it is necessary to restart AD conversion.
Note that since the analog reference voltage is automatically disconnected, there is no possibility of current flowing
into the analog reference voltage.
Page 157
14. 10-bit AD Converter (ADC)
14.5 Analog Input Voltage and AD Conversion Result
TMP86CH12MG
14.5 Analog Input Voltage and AD Conversion Result
The analog input voltage is corresponded to the 10-bit digital value converted by the AD as shown in Figure 14-4.
3FFH
3FEH
3FDH
AD
conversion
result
03H
02H
01H
VDD
0
1
2
3
1021 1022 1023 1024
Analog input voltage
VSS
1024
Figure 14-4 Analog Input Voltage and AD Conversion Result (Typ.)
Page 158
TMP86CH12MG
14.6 Precautions about AD Converter
14.6.1 Analog input pin voltage range
Make sure the analog input pins (AIN0 to AIN7) are used at voltages within VDD to VSS. If any voltage
outside this range is applied to one of the analog input pins, the converted value on that pin becomes uncertain.
The other analog input pins also are affected by that.
14.6.2 Analog input shared pins
The analog input pins (AIN0 to AIN7) are shared with input/output ports. When using any of the analog
inputs to execute AD conversion, do not execute input/output instructions for all other ports. This is necessary
to prevent the accuracy of AD conversion from degrading. Not only these analog input shared pins, some other
pins may also be affected by noise arising from input/output to and from adjacent pins.
14.6.3 Noise Countermeasure
The internal equivalent circuit of the analog input pins is shown in Figure 14-5. The higher the output
impedance of the analog input source, more easily they are susceptible to noise. Therefore, make sure the output impedance of the signal source in your design is 5 kΩ or less. Toshiba also recommends attaching a capacitor external to the chip.
Internal resistance
AINi
Permissible signal
source impedance
5 kΩ (typ)
Analog comparator
Internal capacitance
C = 15 pF (typ.)
5 kΩ (max)
DA converter
Note) i = 7 to 0
Figure 14-5
Analog Input Equivalent Circuit and Example of Input Pin Processing
Page 159
14. 10-bit AD Converter (ADC)
14.6 Precautions about AD Converter
TMP86CH12MG
Page 160
TMP86CH12MG
15. Key-on Wakeup (KWU)
In the TMP86CH12MG, the STOP mode is released by not only P20(INT5/STOP) pin but also four (STOP0 to
STOP3) pins.
When the STOP mode is released by STOP0 to STOP3 pins, the STOP pin needs to be used.
In details, refer to the following section " 15.2 Control ".
15.1 Configuration
INT5
STOP
STOP mode
release signal
(1: Release)
STOP0
STOP1
STOP2
STOPCR
(0F88H)
STOP3
STOP2
STOP1
STOP0
STOP3
Figure 15-1 Key-on Wakeup Circuit
15.2 Control
STOP0 to STOP3 pins can controlled by Key-on Wakeup Control Register (STOPCR). It can be configured as
enable/disable in 1-bit unit. When those pins are used for STOP mode release, configure corresponding I/O pins to
input mode by I/O port register beforehand.
Key-on Wakeup Control Register
STOPCR
7
6
5
4
(0F88H)
STOP3
STOP2
STOP1
STOP0
3
2
1
0
(Initial value: 0000 ****)
STOP3
STOP mode released by STOP3
0:Disable
1:Enable
Write
only
STOP2
STOP mode released by STOP2
0:Disable
1:Enable
Write
only
STOP1
STOP mode released by STOP1
0:Disable
1:Enable
Write
only
STOP0
STOP mode released by STOP0
0:Disable
1:Enable
Write
only
15.3 Function
Stop mode can be entered by setting up the System Control Register (SYSCR1), and can be exited by detecting the
"L" level on STOP0 to STOP3 pins, which are enabled by STOPCR, for releasing STOP mode (Note1).
Page 161
15. Key-on Wakeup (KWU)
15.3 Function
TMP86CH12MG
Also, each level of the STOP0 to STOP3 pins can be confirmed by reading corresponding I/O port data register,
check all STOP0 to STOP3 pins "H" that is enabled by STOPCR before the STOP mode is startd (Note2).
Note 1: When the STOP mode released by the edge release mode (SYSCR1<RELM> = “0”), inhibit input from STOP0 to
STOP3 pins by Key-on Wakeup Control Register (STOPCR) or must be set "H" level into STOP0 to STOP3 pins
that are available input during STOP mode.
Note 2: When the STOP pin input is high or STOP0 to STOP3 pins inputwhich is enabled by STOPCR is low, executing an
instruction which starts STOP mode will not place in STOP mode but instead will immediately start the release
sequence (Warm up).
Note 3: STOP pin doesn’t have the control register such as STOPCR, so when STOP mode is released by STOP0 to
STOP3 pins, STOP pin also should be used as STOP mode release function.
Note 4: In STOP mode, Key-on Wakeup pin which is enabled as input mode (for releasing STOP mode) by Key-on
Wakeup Control Register (STOPCR) may genarate the penetration current, so the said pin must be disabled AD
conversion input (analog voltage input).
Note 5: When the STOP mode is released by STOP0 to STOP3 pins, the level of STOP pin should hold "L" level (Figure
15-2).
b) In case of STOP0 to STOP3
a) STOP
STOP pin
STOP pin "L"
STOP mode
Release
STOP mode
STOP0 pin
STOP mode
Release
STOP mode
Figure 15-2 Priority of STOP pin and STOP0 to STOP3 pins
Table 15-1 Release level (edge) of STOP mode
Release level (edge)
Pin name
SYSCR1<RELM>="1"
(Note2)
SYSCR1<RELM>="0"
STOP
"H" level
Rising edge
STOP0
"L" level
Don’t use (Note1)
STOP1
"L" level
Don’t use (Note1)
STOP2
"L" level
Don’t use (Note1)
STOP3
"L" level
Don’t use (Note1)
Page 162
TMP86CH12MG
16. Input/Output Circuit
16.1 Control pins
The input/output circuitries of the TMP86CH12MG control pins are shown below.
Control Pin
I/O
Input/Output Circuitry
Remarks
Osc.enable
fc
VDD
XIN
XOUT
Resonator connecting pins
(high frequency)
VDD
Rf
Input
Output
RO
Rf = 1.2 MΩ (typ.)
RO =0.5 kΩ (typ.)
XIN
XOUT
XTEN
Osc.enable
XTIN
XTOUT
Input
Output
fs
VDD
VDD
Rf
RO
Resonator connecting pins
(Low frequency)
Rf = 6 MΩ (typ.)
RO = 220 kΩ (typ.)
XTIN
XTOUT
VDD
R RIN
RESET
Input
Address-trap-reset
Hysteresis input
Pull-up resistor
RIN = 220 kΩ (typ.)
R = 100 Ω (typ.)
Watchdog-timer-reset
System-clock-reset
VDD
TEST
Input
Pull-down resistor
RIN = 70 kΩ (typ.)
R
RIN
Page 163
R = 100 Ω (typ.)
16. Input/Output Circuit
16.2 Input/Output Ports
TMP86CH12MG
16.2 Input/Output Ports
Port
I/O
Input/Output Circuitry
Remarks
Initial "High-Z"
Pch control
Data output
P0
I/O
VDD
Sink open drain output or
Tri-state output
Hysteresis input
High current output
R = 100 Ω (typ.)
Input from
output latch
R
Disable
Pin input
+PKVKCN"*KIJ<"
VDD
&CVCQWVRWV
P1
Tri-state I/O
R = 100 Ω (typ.)
I/O
&KUCDNG
R
2KPKPRWV
Initial "High-Z"
P2
I/O
VDD
Data output
Input from
output latch
R
Sink open drain output
Hysteresis input
R = 100 Ω (typ.)
Pin input
Initial "High-Z"
Analog input
VDD
Data output
P3
I/O
Tri-state I/O
Hysteresis input
Input from
output latch
R = 100 Ω (typ.)
R
Disable
Pin input
Page 164
TMP86CH12MG
17. Electrical Characteristics
17.1 Absolute Maximum Ratings
The absolute maximum ratings are rated values, which must not be exceeded during operation, even for an instant.
Any one of the ratings must not be exceeded. If any absolute maximum rating is exceeded, a device may break down
or its performance may be degraded, causing it to catch fire or explode resulting in injury to the user. Thus, when
designing products which include this device, ensure that no absolute maximum rating value will ever be exceeded.
(VSS = 0 V)
Parameter
Symbol
Output Current (Per 1 pin)
Output Current (Total)
Rating
-0.3 to 6.5
VIN
-0.3 to VDD +0.3
VOUT
-0.3 to VDD +0.3
Input Voltage
Output Voltage
Pins
VDD
Supply Voltage
IOUT1
P0, P1, P3 ports
−1.8
IOUT2
P1, P2, P3 ports
3.2
IOUT3
P0 ports
30
Σ IOUT1
P0, P1, P3 ports
−30
Σ IOUT2
P1, P2, P3 ports
60
Σ IOUT3
P0 ports
80
Power Dissipation [Topr = 85°C]
PD
145
Soldering Temperature (Time)
Tsld
260 (10 s)
Storage Temperature
Tstg
−55 to 125
Operating Temperature
Topr
−40 to 85
Unit
V
mA
mW
°C
17.2 Recommended Operating Condition
The recommended operating conditions for a device are operating conditions under which it can be guaranteed that
the device will operate as specified. If the device is used under operating conditions other than the recommended
operating conditions (supply voltage, operating temperature range, specified AC/DC values etc.), malfunction may
occur. Thus, when designing products which include this device, ensure that the recommended operating conditions
for the device are always adhered to.
(VSS = 0 V, Topr = −40 to 85°C)
Parameter
Supply Voltage
Symbol
Pins
VDD
Condition
fc = 16 MHz
NORMAL1, 2 mode
IDLE0, 1, 2 mode
fc = 8 MHz
NORMAL1, 2 mode
IDLE0, 1, 2 mode
fs = 32.768 kHz
SLOW1, 2 mode
SLEEP0, 1, 2 mode
Min
Max
Unit
4.5
5.5
2.7
STOP mode
Input high Level
VIH1
Except Hysteresis input
VIH2
Hysteresis input
VDD < 4.5 V
VIH3
Input low Level
VIL1
Except Hysteresis input
VIL2
Hysteresis input
VDD ≥ 4.5 V
fc
XIN, XOUT
fs
XTIN, XTOUT
VDD = 2.7 to 5.5 V
VDD = 4.5 to 5.5 V
VDD = 2.7 to 5.5 V
Page 165
V
VDD ×0.70
VDD ×0.75
VDD
VDD ×0.90
VDD ×0.30
0
VDD ×0.25
VDD ×0.10
VDD < 4.5 V
VIL3
Clock Frequency
VDD ≥ 4.5 V
1.0
30.0
8.0
16.0
34.0
MHz
kHz
17. Electrical Characteristics
17.3 DC Characteristics
TMP86CH12MG
17.3 DC Characteristics
(VSS = 0.0 V, Topr = −40 to 85°C)
Parameter
Hysteresis Voltage
Input Current
Input Resistance
Symbol
Pins
VHS
Hysteresis input
IIN1
TEST
IIN2
Sink Open-drain, Tristate
IIN3
RESET
RIN1
TEST Pull-Down
Condition
Min
Typ.
Max
Unit
–
0.9
–
V
VDD = 5.5 V, VIN = 5.5 V/0 V
–
–
± 2
µA
VDD = 5.5 V, VIN = 5.5 V
–
70
–
100
220
450
RIN2
RESET Pull-Up
VDD = 5.5 V, VIN = 0 V
ILO1
Sink open drain port
VDD = 5.5 V, VOUT = 5.5 V
–
–
2
ILO2
Tri–state port
VDD = 5.5 V, VOUT = 5.5 V/0 V
–
–
±2
Output High Voltage
VOH
Tri-state Port
VDD = 4.5 V, IOH = -0.7 mA
4.1
–
–
Output Low Voltage
VOL
Except XOUT, P0 Port
VDD = 4.5 V, IOL = 1.6 mA
–
–
0.4
Output Low Current
IOL
High Current Port
(P0 Port)
VDD = 4.5 V, VOL = 1.0 V
–
20
–
VDD = 5.5 V
–
10
13
–
6.5
10
–
8
18
–
5
15
–
4
12
–
0.5
10
Output leakage current
Supply Current in
NORMAL1, 2 mode
VIN = 5.3/0.2 V
fc = 16 MHz
fs = 32.768 kHz
Supply Current in IDLE0,
1, 2 mode
Supply Current in
SLOW1 mode
Supply Current in
SLEEP1 mode
IDD
VDD = 3.0 V
VIN = 2.8 V/0.2 V
fs = 32.768 kHz
Supply Current in
SLEEP0 mode
Supply Current in STOP
mode
VDD = 5.5 V
VIN = 5.3 V/0.2 V
µA
V
mA
µA
Note 1: Typical values show those at Topr = 25°C, VDD = 5 V
Note 2: Input current (IIN1,IIN3); The current through pull-up or pull-down resistor is not included.
Note 3: The supply current in SLOW 2 and SLEEP 2 mode are similar with the supply current in IDLE0, 1, 2 mode.
Page 166
kΩ
TMP86CH12MG
17.4 AD Conversion Characteristics
(VSS = 0.0 V, 4.5 V ≤ VDD ≤ 5.5 V, Topr = −40 to 85°C)
Parameter
Analog Input Voltage
Symbol
Condition
VAIN
Min
Typ.
Max
Unit
VSS
–
VDD
V
–
–
±4
Non linearity Error
Zero Point Error
VDD = 5.0 V
–
–
±4
Full Scale Error
VSS = 0.0 V
–
–
±4
–
–
±4
Min
Typ.
Max
Unit
VSS
–
VDD
V
Total Error
LSB
(VSS = 0.0 V, 2.7 V ≤ VDD< 4.5 V, Topr = −40 to 85°C)
Parameter
Analog Input Voltage
Symbol
Condition
VAIN
–
–
±4
Zero Point Error
VDD = 3.0 V
–
–
±4
Full Scale Error
VSS = 0.0 V
–
–
±4
–
–
±4
Non linearity Error
Total Error
LSB
Note 1: The total error includes all errors except a quantization error, and is defined as a maximum deviation from the ideal conversion line.
Note 2: Conversion time is different in recommended value by power supply voltage.
About conversion time, please refer to “10-bit AD converter (ADC)”.
Note 3: Please use input voltage to AIN input Pin in limit of VDD − VSS.
When voltage of range outside is input, conversion value becomes unsettled and gives affect to other channel conversion
value.
17.5 AC Characteristics
(VSS = 0 V,4.5 V ≤ VDD ≤ 5.5 V, Topr = −40 to 85°C)
Parameter
Symbol
Condition
Min
Typ.
Max
0.25
–
4
117.6
–
133.3
For external clock operation (XIN
input) fc = 16 MHz
–
31.25
–
ns
For external clock operation
(XTIN input) fs = 32.768 kHz
–
15.26
–
µs
Min
Typ.
Max
Unit
0.5
–
4
NORMAL1, 2 mode
Machine Cycle Time
tcy
IDLE0, 1, 2 mode
SLOW1, 2 mode
SLEEP0, 1, 2 mode
High Level Clock Pulse Width
tWCH
Low Level Clock Pulse Width
tWCL
High Level Clock Pulse Width
tWSH
Low Level Clock Pulse Width
tWSL
Unit
µs
(VSS = 0 V, 2.7 V ≤ VDD< 4.5 V, Topr = −40 to 85°C)
Parameter
Symbol
Condition
NORMAL1, 2 mode
Machine Cycle Time
tcy
IDLE0, 1, 2 mode
SLOW1, 2 mode
117.6
–
133.3
For external clock operation (XIN
input) fc = 4.2 MHz
–
62.5
–
ns
For external clock operation
(XTIN input) fs = 32.768 kHz
–
15.26
–
µs
SLEEP0, 1, 2 mode
High Level Clock Pulse Width
tWCH
Low Level Clock Pulse Width
tWCL
High Level Clock Pulse Width
tWSH
Low Level Clock Pulse Width
tWSL
µs
Page 167
17. Electrical Characteristics
17.6 Recommended Oscillating Conditions
TMP86CH12MG
17.6 Recommended Oscillating Conditions
XIN
C1
XOUT
XTIN
C2
(1) High-frequency Oscillation
XTOUT
C1
C2
(2) Low-frequency Oscillation
Note 1: To ensure stable oscillation, the resonator position, load capacitance, etc. must be appropriate. Because these factors are
greatly affected by board patterns, please be sure to evaluate operation on the board on which the device will actually be
mounted.
Note 2: For the resonators to be used with Toshiba microcontrollers, we recommend ceramic resonators manufactured by Murata
Manufacturing Co., Ltd.
For details, please visit the website of Murata at the following URL:
http://www.murata.com
17.7 Handling Precaution
- The solderability test conditions for lead-free products (indicated by the suffix G in product name) are shown
below.
1. When using the Sn-37Pb solder bath
Solder bath temperature = 230 °C
Dipping time = 5 seconds
Number of times = once
R-type flux used
2. When using the Sn-3.0Ag-0.5Cu solder bath
Solder bath temperature = 245 °C
Dipping time = 5 seconds
Number of times = once
R-type flux used
Note: The pass criteron of the above test is as follows:
Solderability rate until forming ≥ 95 %
- When using the device (oscillator) in places exposed to high electric fields such as cathode-ray tubes, we
recommend electrically shielding the package in order to maintain normal operating condition.
Page 168
TMP86CH12MG
18. Package Dimension
P-SSOP30-56-0.65
Unit: mm
Page 169
18. Package Dimension
TMP86CH12MG
Page 170
This is a technical document that describes the operating functions and electrical specifications of the 8-bit
microcontroller series TLCS-870/C (LSI).
Toshiba provides a variety of development tools and basic software to enable efficient software
development.
These development tools have specifications that support advances in microcomputer hardware (LSI) and
can be used extensively. Both the hardware and software are supported continuously with version updates.
The recent advances in CMOS LSI production technology have been phenomenal and microcomputer
systems for LSI design are constantly being improved. The products described in this document may also
be revised in the future. Be sure to check the latest specifications before using.
Toshiba is developing highly integrated, high-performance microcomputers using advanced MOS
production technology and especially well proven CMOS technology.
We are prepared to meet the requests for custom packaging for a variety of application areas.
We are confident that our products can satisfy your application needs now and in the future.