ONSEMI LM392DR2G

LM392
Low Power Operational
Amplifier and Comparator
The LM392 contains two functions: an op amp and a comparator.
Both devices can operate on single−supply power and both have a
common−mode range down to ground. Operation from split power
supplies is also possible. Low power−supply current is independent of
the supply voltage level. The output of the comparator interfaces
directly with either TTL or CMOS logic. Low quiescent current makes
the LM392 ideal for portable equipment.
MARKING
DIAGRAM
8
Features
•
•
•
•
•
•
http://onsemi.com
8
1
Wide Power−Supply Range: 3 V to 32 V
Low Input Offset Voltage: 2 mV
Low Quiescent Current: 600 mA
Input CMV Range includes GND
Op Amp is Unity Gain Stable
These Devices are Pb−Free and are RoHS Compliant
SOIC−8 NB
CASE 751
XXXXX
A
L
Y
W
G
Typical Applications
• Level Detectors
• Voltage Controlled Oscillators
• Transducer Amplifiers
1
LM392
ALYWX
G
= Specific Device Code
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
ORDERING INFORMATION
OUTPUT A (Comparator)
INVERTING INPUT A
1
8
2
−
A
+
+
B
V+
7
See detailed ordering and shipping information in the package
dimensions section on page 4 of this data sheet.
OUTPUT B (Operational Amplifier)
−
NONINVERTING INPUT A
3
6
INVERTING INPUT B
GND
4
5
NONINVERTING INPUT B
Figure 1. Logic Diagram and Pinout
© Semiconductor Components Industries, LLC, 2009
September, 2009 − Rev. 4
1
Publication Order Number:
LM392/D
LM392
MAXIMUM RATINGS
Rating
Symbol
Value
Unit
VS
32 or $16
V
VIDR
32
V
Input Voltage
VI
0.3 to 32
V
Output Short − Circuit to Ground
tSO
Continuous
Thermal Impedance
qJA
160
°C/W
Storage Temperature Range
Tstg
−65 to 150
°C
260
°C
Supply Voltage
Differential Input Voltage
Lead Temperature (Soldering, 10 Seconds)
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
http://onsemi.com
2
LM392
ELECTRICAL CHARACTERISTICS (Both Amplifiers) (V+ = 5 V, TA= 25°C unless otherwise stated)
LM392
Conditions
TA
At output switch point, VO = 1.4 V,
Rs = 0 W, V+ = 5 V to 30 V, VCM = 0 to
(V+ − 1.5 V)
25°C
0°C to 70°C
IN(+) or IN(−), VCM = 0 V
25°C
IN(+) or IN(−)
0°C to 70°C
IN(+) or IN(−)
25°C
Parameter
Input Offset Voltage
Input Bias Current
Input Offset Current
Min
Typ
Max
Unit
$2
$5
mV
$7
50
Input Common−Mode Voltage
Range
= 30 V
(Note 1)
Supply Current
25°C
0°C to 70°C
V+ = 30 V
No Load
$5
f = 1 kHz to 20 kHz, Input Referred
Differential Input Voltage
All VIN w V (or
ELECTRICAL CHARACTERISTICS
(V+
V−,
If Used )
$50
nA
$150
0
V+−1.5
0
V+−2
0°C to 70°C
V+ = 5 V
Amplifier−to−Amplifier Coupling
nA
400
0°C to 70°C
V+
205
25°C
1
2
0.5
1
−78
0°C to 70°C
V
mA
dB
32
V
Max
Unit
= 5 V, TA= 25°C unless otherwise stated)
LM392
Conditions
TA
Min
Typ
V+ = 15 V, Vo Swing = 1 V to 11 V,
RL = 2 kW
25°C
25
100
RL = 2 kW
25°C
V+−1.7
Output Voltage Swing, Low (VOL)
RL = 2 kW
25°C
Common−Mode Rejection Ratio
VCM = 0 to V+ − 1.5 V
25°C
65
70
dB
25°C
65
100
dB
Parameter
OP AMP ONLY
Large Signal Voltage Gain
Output Voltage Swing, High (VOH)
Power Supply Rejection Ratio
V/mV
V
20
mV
Output Current Source
VIN(+) = 1 V, VIN(−) = 0 V,
V+ = 15 V, VO = 2 V
25°C
20
40
mA
Output Current Sink
VIN(−) = 1 V, VIN(+) = 0 V,
V+ = 15 V, VO = 2 V
25°C
10
20
mA
VIN(−) = 1 V, VIN(+) = 0 V,
V+ = 15 V, VO = 200 mV
25°C
12
50
mA
Input Offset Voltage Drift
RS = 0 W (0°C to 70°C)
0°C to 70°C
7
mV/°C
Input Offset Current Drift
RS = 0 W (0°C to 70°C)
0°C to 70°C
10
pA/°C
RL w 15 kW, V+ = 15 V
25°C
200
V/mV
VIN = TTL Logic Swing, VREF = 1.4 V,
VRL = 5 V, RL = 5.1 kW
25°C
200
ns
VRL = 5 V, RL = 5.1 kW
25°C
600
ns
Output Sink Current
VIN(−) = 1 V, VIN(+) = 0 V, VO w 1.5 V
25°C
16
mA
Saturation Voltage
VIN(−) w 1 V, VIN(+) = 0, ISINK v 4 mA
25°C
VIN(−) w 1 V, VIN(+) = 0, ISINK v 4 mA
0°C to 70°C
VIN(−) = 0, VIN(+) w 1 V, VO = 5 V
25°C
VIN(−) = 0, VIN(+) w 1 V, VO = 30 V
25°C
COMPARATOR ONLY
Voltage Gain
Large Signal Response Time
Response Time
Output Leakage Current
50
6
250
400
mV
700
mV
0.1
nA
1.0
mA
1. The input common−mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3 V. The upper end of
the common−mode voltage range is V+ − 1.5 V, but either or both inputs can go to 32 V without damage.
http://onsemi.com
3
LM392
ORDERING INFORMATION
Device
LM392DR2G
Operating
Temperature Range
0°C to +70°C
Package
Shipping†
SOIC−8
(Pb−Free)
2500 / Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
4
LM392
PACKAGE DIMENSIONS
SOIC−8 NB
CASE 751−07
ISSUE AJ
−X−
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
6. 751−01 THRU 751−06 ARE OBSOLETE. NEW
STANDARD IS 751−07.
A
8
5
S
B
0.25 (0.010)
M
Y
M
1
4
−Y−
K
G
C
N
DIM
A
B
C
D
G
H
J
K
M
N
S
X 45 _
SEATING
PLANE
−Z−
0.10 (0.004)
H
D
0.25 (0.010)
M
Z Y
S
X
M
J
S
MILLIMETERS
MIN
MAX
4.80
5.00
3.80
4.00
1.35
1.75
0.33
0.51
1.27 BSC
0.10
0.25
0.19
0.25
0.40
1.27
0_
8_
0.25
0.50
5.80
6.20
INCHES
MIN
MAX
0.189
0.197
0.150
0.157
0.053
0.069
0.013
0.020
0.050 BSC
0.004
0.010
0.007
0.010
0.016
0.050
0 _
8 _
0.010
0.020
0.228
0.244
SOLDERING FOOTPRINT*
1.52
0.060
7.0
0.275
4.0
0.155
0.6
0.024
1.270
0.050
SCALE 6:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to
any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer
purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
5
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
LM392/D