www.fairchildsemi.com ML4865 High Voltage High Current Boost Regulator Features General Description • • • • The ML4865 is a high voltage, continuous conduction boost regulator designed for DC to DC conversion in multiple cell battery powered systems. Continuous conduction allows the regulator to maximize output current for a given inductor. The maximum switching frequency can exceed 200kHz, allowing the use of small, low cost inductors. The ML4865 is capable of start-up with input voltages as low as 1.8V and generates a 12V output with output voltage accuracy of ±4%. • • • • Guaranteed full load start-up and operation at 1.8V input Continuous conduction mode for high output current Very low quiescent current Pulse frequency modulation and internal synchronous rectification for high efficiency Maximum switching frequency > 200kHz Minimum external components Low ON resistance internal switching FETs Fixed 12V output can be adjusted to lower output voltages Unlike most boost regulators, the ML4865 isolates the load from the battery when the SHDN pin is high. An integrated synchronous rectifier eliminates the need for an external Schottky diode and provides a lower forward voltage drop, resulting in higher conversion efficiency. In addition, low quiescent battery current and variable frequency operation result in high efficiency even at light loads. The ML4865 requires only one inductor and two capacitors to build a very small regulator circuit capable of achieving conversion efficiencies approaching 90%. Block Diagram 4 6 VL1 VL2 SHUTDOWN CONTROL SHDN 7 VIN 3 SYNCHRONOUS RECTIFIER CONTROL START-UP VOUT + 8 – + – SHDN FEEDBACK CONTROL + BOOST CONTROL – PWR GND SENSE 1 2.42V GND 5 2 REV. 1.0.2 8/10/01 ML4865 PRODUCT SPECIFICATION Pin Configuration ML4865 8-Pin SOIC (S08) SENSE 1 8 VOUT GND 2 7 SHDN VIN 3 6 VL2 VL1 4 5 PWR GND TOP VIEW Pin Description PIN NAME FUNCTION 1 SENSE Programming pin for setting the output to any value lower than the normal fixed voltage. 2 GND 3 VIN Battery input voltage. 4 VL1 Boost inductor connection. 5 PWR GND 6 VL2 7 SHDN Pulling this pin to VIN through an external resistor shuts down the regulator, isolating the load from the input. 8 VOUT Boost regulator output. Ground. Return for the internal power transistors. Boost inductor connection. Absolute Maximum Ratings Absolute Maximum Ratings are those values, beyond which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied. Parameter Voltage on any other Pin Min. Max. Units GND – 0.3 16.5 V 2 A Peak Switch Current (IPEAK) Average Switch Current (IAVG) 1 A 150 °C 150 °C Lead Temperature (soldering, 10s) 150 °C Thermal Resistance (θJA) 160 °C/W Junction Temperature Storage Temperature Range -65 Operating Conditions Parameter Temperature Range ML4865CS-2 VIN Voltage Range Without external rectifier With external rectifier 2 Min. Max. Units 0 70 °C 1.8 1.8 6 10 V V REV. 1.0.2 8/10/01 PRODUCT SPECIFICATION ML4865 Electrical Characteristics Unless otherwise specified, VIN = Operating Voltage Range, TA = Operating Temperature Range (Note 1) Symbol Parameter Conditions Min. Typ. Max. Units Supply IIN VIN Current SHDN = 0 or VIN 10 25 µA VOUT Quiescent Current VOUT = VOUT(MAX) + 5% 20 30 µA VL Quiescent Current 0V < VL2 < VOUT -1 1 µA PFM Regulator IL(PEAK) IL Peak Current VIN = 5V 0.8 1.2 1.6 A VOUT Output Voltage See Figure 1 VIN = 5V, SENSE = Open, IOUT = 0 11.72 12.1 12.48 V See Figure 1 VIN = 2.4V, IOUT = 40mA VIN = 5V, IOUT = 160mA 11.52 11.52 12.0 12.0 Threshold Voltage 2.38 2.42 Input Bias Current -150 Load Regulation V V Feedback 2.48 V 150 nA 1.6 V 150 nA Shutdown Threshold Voltage Input Bias Current VSHDN = HIGH to LOW 0.4 -150 0.8 Note: 1. Limits are guaranteed by 100% testing, sampling, or correlation with worst-case test conditions. REV. 1.0.2 8/10/01 3 ML4865 PRODUCT SPECIFICATION ML4865 VIN 100µF IOUT SENSE VOUT GND SHDN VIN VL2 VL1 PWR GND 100µF 27µH (Sumida CD75) Figure 1. Application Test Circuit L1 VIN 3 4 VIN 6 VL1 VL2 SHDN SHUTDOWN CONTROL Q3 7 150mΩ A1 + Q2 – A2 VOUT + 8 + – C1 R1 BOOST CONTROL VOUT – Q1 SENSE 1 FEEDBACK CONTROL + – ISET A3 R2 2.42V Figure 2. PFM Regulator Detailed Block Diagram IL(MAX) ISET IL 0 VOUT VL 0 Q1 ON Q2 OFF Q1 OFF Q2 ON Figure 3. Inductor Current and Voltage Waveforms 4 REV. 1.0.2 8/10/01 PRODUCT SPECIFICATION ML4865 Functional Description Feedback The ML4865 combines a unique form of current mode control with a synchronous rectifier to create a boost converter that can deliver high currents while maintaining high efficiency. Current mode control allows the use of a very small, high frequency inductor and output capacitor. Synchronous rectification replaces the conventional external Schottky diode with an on-chip PMOS FET to reduce losses, eliminate an external component, and allows for load disconnect. Also included on-chip are an NMOS switch and current sense resistor, further reducing the number of external components, which makes the ML4865 very easy to use. The SENSE pin should be left open or bypassed to ground for normal operation. The addition of the resistor divider R1 and R2 causes the input of error amplifier A3 to reach the threshold voltage before the internal resistors do. This allows the ML4865 to provide output voltages lower than the preset 12V if desired. Regulator Operation The ML4865 is a variable frequency, current mode switching regulator. Its unique control scheme converts efficiently over more than three decades of load current. A detailed block diagram of the boost converter is shown in Figure 2. Error amplifier A3 converts deviations in the desired output voltage to a small current, ISET. The inductor current is measured through a 150mΩ resistor which is amplified by A1. The boost control block matches the average inductor current to a multiple of the ISET current by switching Q1 on and off. The peak inductor current is limited by the controller to about 1.2A. At light loads, ISET will momentarily reach zero after an inductor discharge cycle causing Q1 to stop switching. Depending on the load, this idle time can extend to tenths of seconds. While the circuit is not switching, only 25µA of supply current is drawn from the output. This allows the part to remain efficient even when the load current drops below 250µA. Amplifier A2 and the PMOS transistor Q2 work together to form a low drop diode. When transistor Q1 turns off, the current flowing in the inductor causes pin 6 to go high. As the voltage on VL2 rises above VOUT, amplifier A2 allows the PMOS transistor Q2 to turn on. In discontinuous operation, (where IL always returns to zero), A2 uses the resistive drop across the PMOS switch Q2 to sense zero inductor current and turns the PMOS switch off. In continuous operation, the PMOS turn off is independent of A2 and is determined by the boost control circuitry. Typical inductor current and voltage waveforms are shown in Figure 3. Shutdown The SHDN pin should be held low for normal operation. Raising the shutdown voltage above the threshold level will disable the synchronous rectifier, Q2 and Q3, and force ISET to zero. This prevents switching from occurring and disconnects the body diode of Q2 from the output. As a result, the output voltage is allowed to drop below the input voltage and current is prevented from flowing from the input to the output. REV. 1.0.2 8/10/01 Design Considerations Input Voltage Range The input voltage range determines whether an external Schottky diode is necessary or optional. If the input voltage is 6V or lower, the ML4865 can be operated as a stand alone boost regulator with a shutdown that fully isolates the input from the output. Adding an optional Schottky diode extends the input voltage range up to 10V, and improves the efficiency and the output current capability. However, the external diode now provides a leakage path from the input to the output during shutdown. Output Current Capability The maximum current available at the output of the regulator is related to the maximum inductor current by the ratio of the input to output voltage and the full load efficiency. The maximum inductor current is dependent on the input voltage. The full load efficiency may be as low as 65% when the ML4865 is used without a Schottky diode and can exhibit an input voltage dependence when an external diode is used. The maximum output current can be determined by using the typical performance curves shown in Figures 4 and 5, or by calculation using the following empirical equation: IOUT (MAX) ≅ VIN × IIN × η (A) VOUT (1) Where, for applications using the internal synchronous rectifier: IOUT (MAX) ≅ VIN × ((0.05 × VIN ( + 0.4( × 0.65 VOUT IIN = (0.05 × VIN ( + 0.4 η = 0.65 And for applications using an external Schottky: IOUT (MAX) ≅ VIN × ((0.07 × VIN ( + 0.4( × ((0.025 × VIN ( + 0.65 ( VOUT IIN = ( 0.07 × VIN ( + 0.4 η = ( 0.025 × VIN ( + 0.65 5 ML4865 PRODUCT SPECIFICATION The curves and the equations are based on the operating circuit shown in Figure 7. It is recommended to verify the current capability and efficiency for the components selected. 900 WITH EXTERNAL SCHOTTKY IOUT (mA) 700 ML4865 500 VIN C1 47µF 300 VOUT GND SHDN VIN VL2 VL1 PWR GND VOUT C2 47µF R1 1MΩ WITHOUT EXTERNAL SCHOTTKY 100 D1 MBR0520L SENSE 22µH (Sumida CD75) 0 2 0 6 4 8 10 Figure 7. Typical Application Circuit VIN (V) Figure 4. Output Current vs. Input Voltage 100 The ML4865 is able to operate over a wide range of inductor values. A value of 22µH or 33µH is a good choice, but any value between 15µH and 50µH is acceptable. As the inductor value is changed the control circuitry will automatically adjust to keep the inductor current under control. Choosing an inductance value of less than 15µH will reduce the component’s footprint, but the efficiency and maximum output current may drop. VOUT = 12V VIN = 10V EFFICIENCY (%) 90 80 VIN = 5V 70 It is important to use an inductor that is rated to handle 1.5A peak currents without saturating. Also look for an inductor with low winding resistance. A good rule of thumb is to allow 5 to 10mΩ of resistance for each µH of inductance. VIN = 2V 60 with Schottky without Schottky 50 1 Inductor Selection 10 100 1000 IOUT (mA) The final selection of the inductor will be based on trade-offs between size, cost and efficiency. Inductor tolerance, core and copper loss will vary with the type of inductor selected and should be evaluated with a ML4865 under worst case conditions to determine its suitability. Several manufacturers supply standard inductance values in surface mount packages: Figure 5. Efficiency vs. Output Current 300 250 Coilcraft (847) 639-6400 Coiltronics (561) 241-7876 Dale (605) 665-9301 Sumida (847) 956-0666 IIN (mA) 200 Output Capacitor WITH EXTERNAL SCHOTTKY 150 The output capacitor filters the pulses of current from the switching regulator. Since the switching frequency will vary with inductance, the minimum output capacitance required to reduce the output ripple to an acceptable level will be a function of the inductor used. Therefore, to maintain an output voltage with less than 100mV of ripple (due to capacitance) at full load current, use the following equation: 100 50 WITHOUT EXTERNAL SCHOTTKY 0 0 2 4 6 8 VIN (V) Figure 6. No Load Input Current vs. Input Voltage for the Circuit of Figure 7 6 10 COUT = 10 × L (F) VOUT (2) REV. 1.0.2 8/10/01 PRODUCT SPECIFICATION ML4865 The output capacitor’s Equivalent Series Resistance (ESR) and Equivalent Series Inductance (ESL), also contribute to the ripple. Just after the NMOS transistor, Q1, turns off, the current in the output capacitor ramps quickly to between 0.5A and 1.5A. This fast change in current through the capacitor’s ESL causes a high frequency (5ns) spike to appear on the output. After the ESL spike settles, the output still has a ripple component equal to the inductor discharge current times the ESR. To minimize these effects, choose an output capacitor with less than 10nH of ESL and 200mΩ of ESR. Suitable tantalum capacitors can be obtained from the following vendors: AVX TPS Series (207) 282-5111 Sprague 593D Series (207) 324-4140 Kemet T495 Series (864) 963-6300 Sense The SENSE pin should be left open or bypassed to ground for normal operation. The output can be set to voltages lower than the preset value by adding a resistor divider. The output voltage can be determined from the following equation: VOUT = 2.42 × R1 + R2 (V) R2 (3) where R1 and R2 are connected as shown in Figure 2. The value of R2 should be 1MΩ or less to minimize bias current errors. Choose an appropriate value of R2 and calculate the value of R1. R1 = R2 × VOUT − 1 (Ω) 2.42 (4) External Schottky Rectifier Input Capacitor Due to the high input current drawn at startup and possibly during operation, it is recommended to decouple the input with a capacitor with a value of 22µF to 68µF. This filtering prevents the input ripple from affecting the ML4865 control circuitry, and also improves the efficiency by reducing the I squared R losses during the charge cycle of the inductor. Again, a low ESR capacitor (such as tantalum) is recommended. It is also recommended that low source impedance batteries be used. Otherwise, the voltage drop across the source impedance during high input current situations will cause the ML4865 to fail to start-up or to operate unreliably. In general, for two cell applications the source impedance should be less than 200mΩ, which means that small alkaline cells should be avoided. Due to excessive power dissipation, an external Schottky rectifier is required when operating at input voltages above 6V. Even for applications where the input voltage is below 6V, the use of an external rectifier may be necessary to achive efficiency or output current requirements. If an external Schottky is required, look for a device with a voltage rating of 20V or greater. The average forward current rating should be at least 500mA, and the forward voltage should be 600mV or less. Suitable Schottky rectifiers can be obtained from Fairchild Semiconductor. Layout Good layout practices will ensure the proper operation of the ML4865. Some layout guidelines follow: • Use adequate ground and power traces or planes Shutdown • Keep components as close as possible to the ML4865 The SHDN pin is a high impedance input and is noise sensitive. Either drive the SHDN input from a low impedance source or bypass the pin to GND with a 10nF ceramic capacitor. • Use short trace lengths from the inductor to the VL1 and VL2 pins and from the output capacitor to the VOUT pin • Use a single point ground for the ML4865 ground pin, and the input and output capacitors • Separate the ground for the converter circuitry from the ground of the load circuitry and connect at a single point A sample layout is shown in Figure 8. Figure 8. Sample ML4865 Layout REV. 1.0.2 8/10/01 7 ML4865 PRODUCT SPECIFICATION Design Example In order to design a boost converter using the ML4865, it is necessary to define the values of a few parameters. For this example, assume the following design parameters: VIN = 4.75 to 5.25V Next, select an inductor. As previously mentioned, the recommended inductance is 22µH. Make sure that the peak current rating of the inductor is at least 1.5A, and that the DC resistance of the inductor is in the range of 110 to 220mΩ. A Sumida CD75-220 meets these requirements. Finally, the value of the output capacitor is determined using Equation 2: VOUT = 12V I OUT(MAX) = 150mA COUT = 10 × L 10 × 22µH = = 18.3µF VOUT 12V Shutdown required First, it must be determined whether the ML4865 is capable of delivering the output current without an external Schottky rectifier. This is done using Equation 1: IOUT (MAX) V ≅ IN × (( 0.05 × VIN ( + 0.4 ( × 0.65 VOUT IOUT (MAX) ≅ 8 The closest standard value would be a 22µF capacitor with an ESR rating of 200mΩ. An AVX TPSD226M025R0200 would be a good choice. As mentioned previously, the use of an input supply bypass capacitor is highly recommended. Since the output capacitance meets the minimum input capacitance recommended it can also be used for the input. 5.25 × ((0.05 × 5.25( + 0.4( × 0.65 = 188 mA 12 REV. 1.0.2 8/10/01 PRODUCT SPECIFICATION ML4865 Mechanical Dimensions inches (millimeters) Package: S08 8-Pin SOIC 0.189 - 0.199 (4.80 - 5.06) 8 0.148 - 0.158 0.228 - 0.244 (3.76 - 4.01) (5.79 - 6.20) PIN 1 ID 1 0.017 - 0.027 (0.43 - 0.69) (4 PLACES) 0.050 BSC (1.27 BSC) 0.059 - 0.069 (1.49 - 1.75) 0º - 8º 0.055 - 0.061 (1.40 - 1.55) 0.012 - 0.020 (0.30 - 0.51) 0.004 - 0.010 (0.10 - 0.26) 0.015 - 0.035 (0.38 - 0.89) 0.006 - 0.010 (0.15 - 0.26) SEATING PLANE REV. 1.0.2 8/10/01 9 ML4865 PRODUCT SPECIFICATION Ordering Information Part Number Output Voltage Temperature Range Package ML4865CS-2 12V 0°C to 70°C 8 Pin SOIC (S08) DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.fairchildsemi.com 8/10/01 0.0m 001 Stock#DS30004865 © 2001 Fairchild Semiconductor Corporation