MKP3V120, MKP3V240 Preferred Device Sidac High Voltage Bidirectional Triggers Bidirectional devices designed for direct interface with the AC power line. Upon reaching the breakover voltage in each direction, the device switches from a blocking state to a low voltage on−state. Conduction will continue like a Triac until the main terminal current drops below the holding current. The plastic axial lead package provides high pulse current capability at low cost. Glass passivation insures reliable operation. Features • • • • • • • • High Pressure Sodium Vapor Lighting Strobes and Flashers Ignitors High Voltage Regulators Pulse Generators Used to Trigger Gates of SCR’s and Triacs Indicates UL Registered − File #E116110 These are Pb−Free Devices* http://onsemi.com SIDACS ( ) 1 AMPERE RMS 120 and 240 VOLTS MT1 MT2 MARKING DIAGRAM AXIAL LEAD (No Polarity) CASE 267 STYLE 2 MAXIMUM RATINGS (TJ = 25°C unless otherwise noted) Rating Symbol Peak Repetitive Off−State Voltage VDRM, (Sine Wave, 50 to 60 Hz, TJ = − 40 to 125°C) VRRM MKP3V120 MKP3V240 Value V "90 "180 IT(RMS) "1.0 A ITSM "20 A Operating Junction Temperature Range TJ −40 to +125 °C Storage Temperature Range Tstg −40 to +150 °C On-State RMS Current (TL = 80°C, Lead Length = 3/8″, All Conduction Angles) Peak Non−Repetitive Surge Current (60 Hz One Cycle Sine Wave, Peak Value, TJ = 125°C) THERMAL CHARACTERISTICS Characteristic Thermal Resistance, Junction−to−Lead (Lead Length = 3/8″) Lead Solder Temperature (Lead Length w 1/16″ from Case, 10 s Max) ORDERING INFORMATION Package Shipping † MKP3V120 Axial Lead* 500 Units/Box Device Max Unit MKP3V120G Axial Lead* 500 Units/Box RqJL 15 °C/W MKP3V120RL Axial Lead* 1500/Tape & Reel TL 260 °C MKP3V120RLG Axial Lead* 1500/Tape & Reel MKP3V240 Axial Lead* 500 Units/Box MKP3V240G Axial Lead* 500 Units/Box MKP3V240RL Axial Lead* 1500/Tape & Reel MKP3V240RLG Axial Lead* 1500/Tape & Reel *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. February, 2006− Rev. 4 A = Assembly Location YY, Y = Year WW = Work Week G = Pb−Free Package (Note: Microdot may be in either location) Symbol Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected. © Semiconductor Components Industries, LLC, 2006 A MKP 3V120 YYWW G G Unit 1 †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. Preferred devices are recommended choices for future use and best overall value. Publication Order Number: MKP3V120/D MKP3V120, MKP3V240 ELECTRICAL CHARACTERISTICS (TC = 25°C unless otherwise noted; Electricals apply in both directions) Characteristic Symbol Min Typ Max Unit IDRM − − 10 mA 110 220 − − 130 250 OFF CHARACTERISTICS Repetitive Peak Off−State Current (50 to 60 Hz Sine Wave) VDRM = 90 V VDRM = 180 V MKP3V120 MKP3V240 ON CHARACTERISTICS Breakover Voltage, IBO = 200 mA VBO V MKP3V120 MKP3V240 Breakover Current IBO − − 200 mA Peak On−State Voltage (ITM = 1 A Peak, Pulse Width ≤ 300 ms, Duty Cycle ≤ 2%) VTM − 1.1 1.5 V Dynamic Holding Current (Sine Wave, 60 Hz, RL = 100 W) IH − − 100 mA Switching Resistance (Sine Wave, 50 to 60 Hz) RS 0.1 − − kW di/dt − 120 − A/ms DYNAMIC CHARACTERISTICS Critical Rate−of−Rise of On−State Current, Critical Damped Waveform Circuit (IPK = 130 W, Pulse Width = 10 msec) Voltage Current Characteristic of SIDAC (Bidirectional Device) + Current Symbol Parameter IDRM Off State Leakage Current VDRM Off State Repetitive Blocking Voltage VBO Breakover Voltage IBO Breakover Current IH Holding Current VTM On State Voltage ITM Peak on State Current ITM VTM Slope = RS IH IS IDRM VDRM RS + http://onsemi.com 2 VS I(BO) + Voltage V(BO) (V (BO) – V S) (I S – I (BO)) MKP3V120, MKP3V240 TC , MAXIMUM ALLOWABLE CASE TEMPERATURE (° C) CURRENT DERATING TA , MAXIMUM ALLOWABLE AMBIENT TEMPERATURE (° C) 130 120 α α = Conduction Angle TJ Rated = 125°C 110 90 a = 180° 80 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 α = Conduction Angle TJ Rated = 125°C 120 100 80 a = 180° 60 40 20 0 2.0 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 IT(AV), AVERAGE ON−STATE CURRENT (AMPS) IT(AV), AVERAGE ON−STATE CURRENT (AMPS) Figure 1. Maximum Case Temperature Figure 2. Maximum Ambient Temperature PAV , MAXIMUM AVERAGE POWER DISSIPATION (WATTS) I T , INSTANTANEOUS ON−STATE CURRENT (AMPS) 100 α 140 1.0 1.25 25°C 0.8 125°C a = 180° 1.00 0.6 0.4 α α = Conduction Angle TJ Rated = 125°C 0.75 0.3 2.0 0.50 0.2 0.25 0.1 0.8 0.9 1.0 1.1 1.2 1.3 VT, INSTANTANEOUS ON−STATE VOLTAGE (VOLTS) 0 Figure 3. Typical Forward Voltage 0.2 0.4 0.6 0.8 IT(AV), AVERAGE ON−STATE CURRENT (AMPS) Figure 4. Typical Power Dissipation http://onsemi.com 3 1.0 MKP3V120, MKP3V240 r(t), TRANSIENT THERMAL RESISTANCE (NORMALIZED) THERMAL CHARACTERISTICS 1.0 ZqJL(t) = RqJL • r(t) DTJL = Ppk RqJL[r(t)] tp TIME where: DTJL = the increase in junction temperature above the lead temperature r(t) = normalized value of transient thermal resistance at time, t from this figure. For example, r(tp) = normalized value of transient resistance at time tp. 0.5 0.3 0.2 0.1 0.05 LEAD LENGTH = 1/4″ The temperature of the lead should be measured using a thermocouple placed on the lead as close as possible to the tie point. The thermal mass connected to the tie point is normally large enough so that it will not significantly respond to heat surges generated in the diode as a result of pulsed operation once steady−state conditions are achieved. Using the measured value of TL, the junction temperature may be determined by: 0.03 0.02 TJ = TL + DTJL 0.01 0.2 0.5 1.0 2.0 5.0 20 10 50 100 200 500 1.0 k 2.0 k 5.0 k 10 k 20 k t, TIME (ms) Figure 5. Thermal Response TYPICAL CHARACTERISTICS 225 80 200 IH , HOLDING CURRENT (mA) 250 90 I(BO) , BREAKOVER CURRENT (m A) 100 70 60 50 40 30 20 10 0 −60 175 150 125 100 75 50 25 −40 −20 0 20 40 60 80 120 100 0 −60 140 −40 −20 0 20 40 60 80 100 TJ, JUNCTION TEMPERATURE (°C) TJ, JUNCTION TEMPERATURE (°C) Figure 6. Typical Breakover Current Figure 7. Typical Holding Current http://onsemi.com 4 120 140 MKP3V120, MKP3V240 PACKAGE DIMENSIONS AXIAL LEAD CASE 267−05 ISSUE G K D A 1 B 2 K NOTES: 1. DIMENSIONS AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. 267−04 OBSOLETE, NEW STANDARD 267−05. DIM A B D K INCHES MIN MAX 0.287 0.374 0.189 0.209 0.047 0.051 1.000 −−− MILLIMETERS MIN MAX 7.30 9.50 4.80 5.30 1.20 1.30 25.40 −−− STYLE 2: NO POLARITY ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: N. American Technical Support: 800−282−9855 Toll Free Literature Distribution Center for ON Semiconductor USA/Canada P.O. Box 61312, Phoenix, Arizona 85082−1312 USA Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center 2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051 Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada Phone: 81−3−5773−3850 Email: [email protected] http://onsemi.com 5 ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder For additional information, please contact your local Sales Representative. MKP3V120/D