ONSEMI MC74LVXT8051M

MC74LVXT8051
Analog Multiplexer /
Demultiplexer
High−Performance Silicon−Gate CMOS
The MC74LVXT8051 utilizes silicon−gate CMOS technology to
achieve fast propagation delays, low ON resistances, and low OFF
leakage currents. This analog multiplexer/demultiplexer controls
analog voltages that may vary across the complete power supply range
(from VCC to GND).
The LVXT8051 is similar in pinout to the high−speed HC4051A
and the metal−gate MC14051B. The Channel−Select inputs determine
which one of the Analog Inputs/Outputs is to be connected by means
of an analog switch to the Common Output/Input. When the Enable
pin is HIGH, all analog switches are turned off.
The Channel−Select and Enable inputs are compatible with
TTL−type input thresholds. The input protection circuitry on this
device allows overvoltage tolerance on the input, allowing the device
to be used as a logic−level translator from 3.0 V CMOS logic to 5.0V
CMOS Logic or from 1.8V CMOS logic to 3.0 V CMOS Logic while
operating at the higher−voltage power supply.
The MC74LVXT8051 input structure provides protection when
voltages up to 7.0 V are applied, regardless of the supply voltage. This
allows the MC74LVXT8051 to be used to interface 5.0 V circuits to
3.0 V circuits.
This device has been designed so that the ON resistance (Ron) is
more linear over input voltage than Ron of metal−gate CMOS analog
switches.
Features
•
•
•
•
•
•
•
•
•
Fast Switching and Propagation Speeds
Low Crosstalk Between Switches
Diode Protection on All Inputs/Outputs
Analog Power Supply Range (VCC − GND) = 2.0 to 6.0 V
Digital (Control) Power Supply Range (VCC − GND) = 2.0 to 6.0 V
Improved Linearity and Lower ON Resistance Than Metal−Gate
Counterparts
Low Noise
In Compliance With the Requirements of JEDEC Standard No. 7A
Pb−Free Packages are Available*
http://onsemi.com
MARKING
DIAGRAMS
16
SOIC−16
D SUFFIX
CASE 751B
LVXT8051
AWLYWW
1
16
LVXT
8051
ALYW
TSSOP−16
DT SUFFIX
CASE 948F
1
16
SOEIAJ−16
M SUFFIX
CASE 966
LVXT8051
ALYW
1
A
WL or L
Y
WW or W
=
=
=
=
Assembly Location
Wafer Lot
Year
Work Week
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 2 of this data sheet.
*For additional information on our Pb−Free strategy and soldering details, please
download the ON Semiconductor Soldering and Mounting Techniques
Reference Manual, SOLDERRM/D.
 Semiconductor Components Industries, LLC, 2005
March, 2005 − Rev. 3
1
Publication Order Number:
MC74LVXT8051/D
MC74LVXT8051
FUNCTION TABLE − MC74LVXT8051
Control Inputs
VCC
X2
X1
X0
X3
A
B
C
16
15
14
13
12
11
10
9
1
2
3
4
5
X4
X6
X
X7
X5
6
7
Enable NC
Enable
C
L
L
L
L
L
L
L
L
H
L
L
L
L
H
H
H
H
X
8
GND
PIN CONNECTION AND
MARKING DIAGRAM (Top View)
Select
B
A
L
L
H
H
L
L
H
H
X
L
H
L
H
L
H
L
H
X
ON Channels
X0
X1
X2
X3
X4
X5
X6
X7
NONE
X = Don’t Care
13
X0
14
X1
15
X2
ANALOG
12
INPUTS/ X3
OUTPUTS X4 1
5
X5
2
X6
4
X7
11
A
CHANNEL
10
B
SELECT
9
INPUTS
C
6
ENABLE
3
MULTIPLEXER/
DEMULTIPLEXER
X
COMMON
OUTPUT/
INPUT
PIN 16 = VCC
PIN 8 = GND
Figure 1. LOGIC DIAGRAM
Single−Pole, 8−Position Plus Common Off
ORDERING INFORMATION
Package
Shipping†
MC74LVXT8051D
SOIC−16
48 Units / Rail
MC74LVXT8051DG
SOIC−16
(Pb−Free)
48 Units / Rail
MC74LVXT8051DR2
SOIC−16
2500 Tape & Reel
MC74LVXT8051DR2G
SOIC−16
(Pb−Free)
2500 Tape & Reel
MC74LVXT8051DTR2
TSSOP−16*
2500 Tape & Reel
MC74LVXT8051M
SOEIAJ−16
50 Units / Rail
MC74LVXT8051MG
SOEIAJ−16
(Pb−Free)
50 Units / Rail
MC74LVXT8051MEL
SOEIAJ−16
2000 Tape & Reel
MC74LVXT8051MELG
SOEIAJ−16
(Pb−Free)
2000 Tape & Reel
Device
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*This package is inherently Pb−Free.
http://onsemi.com
2
MC74LVXT8051
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎ
MAXIMUM RATINGS
Symbol
Parameter
Value
Unit
– 0.5 to + 7.0
V
Analog Input Voltage
− 0.5 to VCC + 0.5
V
Digital Input Voltage (Referenced to GND)
– 0.5 to VCC + 0.5
V
DC Current, Into or Out of Any Pin
−20
mA
PD
Power Dissipation in Still Air,
500
450
mW
Tstg
Storage Temperature Range
– 65 to + 150
C
TL
Lead Temperature, 1 mm from Case for 10 Seconds
260
C
VCC
Positive DC Supply Voltage
VIS
Vin
I
(Referenced to GND)
SOIC Package†
TSSOP Package†
Maximum ratings are those values beyond which device damage can occur. Maximum ratings
applied to the device are individual stress limit values (not normal operating conditions) and are
not valid simultaneously. If these limits are exceeded, device functional operation is not implied,
damage may occur and reliability may be affected.
†Derating − SOIC Package: – 7 mW/C from 65 to 125C
TSSOP Package: − 6.1 mW/C from 65 to 125C
This device contains protection
circuitry to guard against damage
due to high static voltages or electric
fields. However, precautions must
be taken to avoid applications of any
voltage higher than maximum rated
voltages to this high−impedance circuit. For proper operation, Vin and
Vout should be constrained to the
range GND (Vin or Vout) VCC.
Unused inputs must always be
tied to an appropriate logic voltage
level (e.g., either GND or V CC ).
Unused outputs must be left open.
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
RECOMMENDED OPERATING CONDITIONS
Symbol
Parameter
VCC
Positive DC Supply Voltage
VIS
Analog Input Voltage
Vin
Digital Input Voltage (Referenced to GND)
VIO*
Static or Dynamic Voltage Across Switch
Min
Max
Unit
2.0
6.0
V
0.0
VCC
V
GND
VCC
V
1.2
V
(Referenced to GND)
TA
Operating Temperature Range, All Package Types
tr, tf
Input Rise/Fall Time
(Channel Select or Enable Inputs)
VCC = 3.3 V ± 0.3 V
VCC = 5.0 V ± 0.5 V
– 55
+ 85
C
ns/V
0
0
100
20
*For voltage drops across switch greater than 1.2 V (switch on), excessive VCC current may be
drawn; i.e., the current out of the switch may contain both VCC and switch input components. The
reliability of the device will be unaffected unless the Maximum Ratings are exceeded.
DC CHARACTERISTICS − Digital Section (Voltages Referenced to GND)
Symbol
Parameter
Condition
Guaranteed Limit
VCC
V
−55 to 25°C
≤85°C
≤125°C
Unit
VIH
Minimum High−Level Input Voltage,
Channel−Select or Enable Inputs
Ron = Per Spec
3.0
4.5
5.5
1.2
2.0
2.0
1.2
2.0
2.0
1.2
2.0
2.0
V
VIL
Maximum Low−Level Input Voltage,
Channel−Select or Enable Inputs
Ron = Per Spec
3.0
4.5
5.5
0.53
0.8
0.8
0.53
0.8
0.8
0.53
0.8
0.8
V
Iin
Maximum Input Leakage Current,
Channel−Select or Enable Inputs
Vin = VCC or GND
5.5
± 0.1
± 1.0
± 1.0
A
ICC
Maximum Quiescent Supply
Current (per Package)
Channel Select, Enable and
VIS = VCC or GND; VIO = 0 V
5.5
4
40
160
A
http://onsemi.com
3
MC74LVXT8051
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
DC ELECTRICAL CHARACTERISTICS Analog Section
Guaranteed Limit
Symbol
Ron
VCC
V
−55 to 25°C
85C
125C
Vin = VIL or VIH
VIS = VCC to GND
|IS| 10.0 mA (Figures 1, 2)
3.0
4.5
5.5
40
30
25
45
32
28
50
37
30
Vin = VIL or VIH
VIS = VCC or GND (Endpoints)
|IS| 10.0 mA (Figures 1, 2)
3.0
4.5
5.5
30
25
20
35
28
25
40
35
30
Parameter
Test Conditions
Maximum “ON” Resistance
Unit
Ron
Maximum Difference in “ON”
Resistance Between Any Two
Channels in the Same Package
Vin = VIL or VIH
VIS = 1/2 (VCC − GND)
|IS| 10.0 mA
3.0
4.5
5.5
15
8.0
8.0
20
12
12
25
15
15
Ioff
Maximum Off−Channel Leakage
Current, Any One Channel
Vin = VIL or VIH;
VIO = VCC or GND;
Switch Off (Figure 3)
5.5
0.1
0.5
1.0
A
Maximum Off−Channel
Leakage Current,
Common Channel
Vin = VIL or VIH;
VIO = VCC or GND;
Switch Off (Figure 4)
5.5
0.2
2.0
4.0
Maximum On−Channel
Leakage Current,
Channel−to−Channel
Vin = VIL or VIH;
Switch−to−Switch =
VCC or GND; (Figure 5)
5.5
0.2
2.0
4.0
A
Ion
AC CHARACTERISTICS (CL = 50 pF, Input tr = tf = 3 ns)
Symbol
Parameter
Guaranteed Limit
VCC
V
−55 to 25°C
≤85°C
≤125°C
Unit
tPLH,
tPHL
Maximum Propagation Delay, Channel−Select to Analog Output
(Figure 9)
2.0
3.0
4.5
5.5
30
20
15
15
35
25
18
18
40
30
22
20
ns
tPLH,
tPHL
Maximum Propagation Delay, Analog Input to Analog Output
(Figure 10)
2.0
3.0
4.5
5.5
4.0
3.0
1.0
1.0
6.0
5.0
2.0
2.0
8.0
6.0
2.0
2.0
ns
tPLZ,
tPHZ
Maximum Propagation Delay, Enable to Analog Output
(Figure 11)
2.0
3.0
4.5
5.5
30
20
15
15
35
25
18
18
40
30
22
20
ns
tPZL,
tPZH
Maximum Propagation Delay, Enable to Analog Output
(Figure 11)
2.0
3.0
4.5
5.5
20
12
8.0
8.0
25
14
10
10
30
15
12
12
ns
Cin
Maximum Input Capacitance, Channel−Select or Enable Inputs
10
10
10
pF
CI/O
Maximum Capacitance
Analog I/O
35
35
35
pF
Common O/I
130
130
130
Feedthrough
1.0
1.0
1.0
(All Switches Off)
Typical @ 25°C, VCC = 5.0 V
CPD
45
Power Dissipation Capacitance (Figure 13)*
* Used to determine the no−load dynamic power consumption: P D = CPD VCC
http://onsemi.com
4
2f
+ ICC VCC .
pF
MC74LVXT8051
ADDITIONAL APPLICATION CHARACTERISTICS (GND = 0 V)
Symbol
Parameter
BW
Maximum On−Channel Bandwidth or
Mi i
Minimum
F
Frequency R
Response
(Figure 6)
fin = 1MHz Sine Wave; Adjust fin Voltage to Obtain
0dB att VOS; IIncrease fin Frequency
0dBm
F
Until
U til dB Meter
M t
Reads −3dB;
RL = 50, CL = 10pF
Off−Channel Feedthrough Isolation
(Figure 7)
fin = Sine Wave; Adjust fin Voltage to Obtain 0dBm at
VIS
fin = 10kHz, RL = 600, CL = 50pF
−
Condition
fin = 1.0MHz, RL = 50, CL = 10pF
−
Feedthrough Noise. Channel−Select
Input to Common I/O (Figure 8)
Vin ≤ 1MHz Square Wave (tr = tf = 3ns); Adjust RL at
Setup so that IS = 0A;
Enable = GND
RL = 600, CL = 50pF
RL = 10k, CL = 10pF
−
Crosstalk Between Any Two
Switches (Figure 12)
fin = Sine Wave; Adjust fin Voltage to Obtain 0dBm at
VIS
fin = 10kHz, RL = 600, CL = 50pF
fin = 1.0MHz, RL = 50, CL = 10pF
THD
Total Harmonic Distortion
(Figure 14)
fin = 1kHz, RL = 10k, CL = 50pF
THD = THDmeasured − THDsource
VIS = 2.0VPP sine wave
VIS = 4.0VPP sine wave
VIS = 5.0VPP sine wave
*Limits not tested. Determined by design and verified by qualification.
http://onsemi.com
5
VCC
V
Limit*
25°C
Unit
MHz
3.0
4.5
5.5
80
80
80
3.0
4.5
5.5
−50
−50
−50
3.0
4.5
5.5
−37
−37
−37
3.0
4.5
5.5
25
105
135
3.0
4.5
5.5
35
145
190
3.0
4.5
5.5
−50
−50
−50
3.0
4.5
5.5
−60
−60
−60
dB
mVPP
dB
%
3.0
4.5
5.5
0.10
0.08
0.05
MC74LVXT8051
Ron , ON RESISTANCE (OHMS)
40
35
30
25
125°C
85°C
25°C
−55 °C
20
15
10
5
00
1.0
2.0
3.0
4.0
VIN, INPUT VOLTAGE (VOLTS)
Figure 1a. Typical On Resistance, VCC = 3.0 V
25
25
Ron , ON RESISTANCE (OHMS)
Ron , ON RESISTANCE (OHMS)
30
125°C
85°C
25°C
−55 °C
20
15
10
5
0
0
1.0
2.0
3.0
4.0
20
125°C
85°C
15
25°C
−55 °C
10
5
0
5.0
0
1.0
2.0
VIN, INPUT VOLTAGE (VOLTS)
Figure 1b. Typical On Resistance, VCC = 4.5 V
4.0
5.0
Figure 1c. Typical On Resistance, VCC = 5.5 V
PLOTTER
PROGRAMMABLE
POWER
SUPPLY
−
3.0
VIN, INPUT VOLTAGE (VOLTS)
MINI COMPUTER
DC ANALYZER
+
VCC
DEVICE
UNDER TEST
ANALOG IN
COMMON OUT
GND
GND
Figure 2. On Resistance Test Set−Up
http://onsemi.com
6
6.0
MC74LVXT8051
VCC
VCC
VCC
16
GND
GND
ANALOG I/O
OFF
A
VCC
VIH
OFF
VIH
6
8
Figure 3. Maximum Off Channel Leakage Current,
Any One Channel, Test Set−Up
VCC
Figure 4. Maximum Off Channel Leakage Current,
Common Channel, Test Set−Up
VCC
VCC
16
A
fin
dB
METER
ON
N/C
COMMON O/I
OFF
VOS
16
0.1F
ON
VCC
COMMON O/I
6
8
GND
OFF
VCC
COMMON O/I
OFF
NC
VCC
16
RL
CL*
ANALOG I/O
VIL
6
6
8
8
*Includes all probe and jig capacitance
Figure 5. Maximum On Channel Leakage Current,
Channel to Channel, Test Set−Up
VCC
VIS
VCC
VOS
16
0.1F
fin
dB
METER
OFF
RL
Figure 6. Maximum On Channel Bandwidth,
Test Set−Up
CL*
16
RL
COMMON O/I
ON/OFF
ANALOG I/O
RL
OFF/ON
RL
RL
6
6
8
VIL or VIH
VIH
VIL
CHANNEL SELECT
Vin ≤ 1 MHz
tr = tf = 3 ns
8
CL*
TEST
POINT
VCC
11
CHANNEL SELECT
*Includes all probe and jig capacitance
*Includes all probe and jig capacitance
Figure 7. Off Channel Feedthrough Isolation,
Test Set−Up
Figure 8. Feedthrough Noise, Channel Select to
Common Out, Test Set−Up
http://onsemi.com
7
MC74LVXT8051
VCC
VCC
16
VCC
CHANNEL
SELECT
COMMON O/I
ON/OFF
50%
ANALOG I/O
OFF/ON
GND
tPLH
CL*
TEST
POINT
tPHL
6
ANALOG
OUT
50%
8
CHANNEL SELECT
*Includes all probe and jig capacitance
Figure 9a. Propagation Delays, Channel Select
to Analog Out
Figure 9b. Propagation Delay, Test Set−Up Channel
Select to Analog Out
VCC
16
VCC
ANALOG
IN
COMMON O/I
ANALOG I/O
ON
50%
CL*
TEST
POINT
GND
tPLH
tPHL
ANALOG
OUT
6
8
50%
*Includes all probe and jig capacitance
Figure 10a. Propagation Delays, Analog In
to Analog Out
tf
tr
90%
50%
10%
ENABLE
tPZL
ANALOG
OUT
tPLZ
1
VCC
GND
16
1
1k
ANALOG I/O
ON/OFF
2
CL*
VOL
tPHZ
90%
VCC
VCC
HIGH
IMPEDANCE
10%
POSITION 1 WHEN TESTING tPHZ AND tPZH
POSITION 2 WHEN TESTING tPLZ AND tPZL
2
50%
tPZH
ANALOG
OUT
Figure 10b. Propagation Delay, Test Set−Up
Analog In to Analog Out
VIH
VIL
VOH
ENABLE
50%
8
HIGH
IMPEDANCE
Figure 11a. Propagation Delays, Enable to
Analog Out
6
Figure 11b. Propagation Delay, Test Set−Up
Enable to Analog Out
http://onsemi.com
8
TEST
POINT
MC74LVXT8051
VCC
VIS
A
VCC
16
RL
fin
16
VOS
ON
COMMON O/I
ON/OFF
NC
ANALOG I/O
0.1F
OFF/ON
OFF
RL
RL
CL*
RL
CL*
VCC
6
6
8
8
CHANNEL SELECT
11
*Includes all probe and jig capacitance
Figure 12. Crosstalk Between Any Two
Switches, Test Set−Up
Figure 13. Power Dissipation Capacitance,
Test Set−Up
0
VIS
VCC
−10
VOS
16
0.1F
fin
ON
CL*
TO
DISTORTION
METER
−30
−40
dB
RL
FUNDAMENTAL FREQUENCY
−20
−50
DEVICE
−60
6
SOURCE
−70
8
−80
−90
*Includes all probe and jig capacitance
− 100
1.0
2.0
3.125
FREQUENCY (kHz)
Figure 14a. Total Harmonic Distortion, Test Set−Up
Figure 14b. Plot, Harmonic Distortion
APPLICATIONS INFORMATION
The Channel Select and Enable control pins should be at
VCC or GND logic levels. VCC being recognized as a logic
high and GND being recognized as a logic low. In this
example:
VCC = +5V = logic high
GND = 0V = logic low
The maximum analog voltage swing is determined by the
supply voltage VCC. The positive peak analog voltage
should not exceed VCC. Similarly, the negative peak analog
voltage should not go below GND. In this example, the
difference between VCC and GND is five volts. Therefore,
using the configuration of Figure 15, a maximum analog
signal of five volts peak−to−peak can be controlled. Unused
analog inputs/outputs may be left floating (i.e., not
connected). However, tying unused analog inputs and
outputs to VCC or GND through a low value resistor helps
minimize crosstalk and feedthrough noise that may be
picked up by an unused switch.
Although used here, balanced supplies are not a
requirement. The only constraints on the power supplies are
that:
VCC − GND = 2 to 6 volts
When voltage transients above VCC and/or below GND
are anticipated on the analog channels, external Germanium
or Schottky diodes (Dx) are recommended as shown in
Figure 16. These diodes should be able to absorb the
maximum anticipated current surges during clipping.
http://onsemi.com
9
MC74LVXT8051
VCC
+5V
+5V
16
ANALOG
SIGNAL
0V
ON
6
8
Dx
+5V
ANALOG
SIGNAL
VCC
16
Dx
Dx
GND
GND
8
Figure 15. Application Example
Figure 16. External Germanium or
Schottky Clipping Diodes
+3V
+3V
16
ANALOG
SIGNAL
GND
ON/OFF
ANALOG
SIGNAL
Dx
ON/OFF
0V
TO EXTERNAL LSTTL COMPATIBLE
CIRCUITRY 0 to VIH
DIGITAL SIGNALS
11
10
9
VCC
+5V
+3V
+5V
GND
GND
16
ANALOG
SIGNAL
ON/OFF
+5V
ANALOG
SIGNAL
GND
+5V
6
8
11
10
9
6
1.8V − 2.5V
CIRCUITRY
8
11
10
9
1.8V − 2.5V
CIRCUITRY
MC74VHCT1GT50 BUFFERS
VCC = 3.0V
a. Low Voltage Logic Level Shifting Control
b. 2−Stage Logic Level Shifting Control
Figure 17. Interfacing to Low Voltage CMOS Outputs
A
11
13
LEVEL
SHIFTER
14
B
10
15
LEVEL
SHIFTER
12
C
9
1
LEVEL
SHIFTER
5
ENABLE
6
2
LEVEL
SHIFTER
4
Figure 18. Function Diagram, LVXT8051
http://onsemi.com
10
3
X0
X1
X2
X3
X4
X5
X6
X7
X
MC74LVXT8051
PACKAGE DIMENSIONS
SOIC−16
D SUFFIX
CASE 751B−05
ISSUE J
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
−A−
16
9
−B−
1
P
8 PL
0.25 (0.010)
8
B
M
S
G
R
K
DIM
A
B
C
D
F
G
J
K
M
P
R
F
X 45 C
−T−
SEATING
PLANE
J
M
D
16 PL
0.25 (0.010)
M
T B
S
A
MILLIMETERS
MIN
MAX
9.80
10.00
3.80
4.00
1.35
1.75
0.35
0.49
0.40
1.25
1.27 BSC
0.19
0.25
0.10
0.25
0
7
5.80
6.20
0.25
0.50
INCHES
MIN
MAX
0.386
0.393
0.150
0.157
0.054
0.068
0.014
0.019
0.016
0.049
0.050 BSC
0.008
0.009
0.004
0.009
0
7
0.229
0.244
0.010
0.019
S
TSSOP−16
DT SUFFIX
CASE 948F−01
ISSUE A
16X K REF
0.10 (0.004)
0.15 (0.006) T U
M
T U
V
S
S
S
K
ÉÉÉ
ÇÇÇ
ÇÇÇ
ÉÉÉ
K1
2X
L/2
16
9
J1
B
−U−
L
SECTION N−N
J
PIN 1
IDENT.
8
1
N
0.25 (0.010)
0.15 (0.006) T U
S
A
−V−
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD
FLASH. PROTRUSIONS OR GATE BURRS.
MOLD FLASH OR GATE BURRS SHALL NOT
EXCEED 0.15 (0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE
INTERLEAD FLASH OR PROTRUSION.
INTERLEAD FLASH OR PROTRUSION SHALL
NOT EXCEED 0.25 (0.010) PER SIDE.
5. DIMENSION K DOES NOT INCLUDE
DAMBAR PROTRUSION. ALLOWABLE
DAMBAR PROTRUSION SHALL BE 0.08
(0.003) TOTAL IN EXCESS OF THE K
DIMENSION AT MAXIMUM MATERIAL
CONDITION.
6. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
7. DIMENSION A AND B ARE TO BE
DETERMINED AT DATUM PLANE −W−.
M
N
F
DETAIL E
−W−
C
0.10 (0.004)
−T− SEATING
PLANE
H
D
DETAIL E
G
http://onsemi.com
11
DIM
A
B
C
D
F
G
H
J
J1
K
K1
L
M
MILLIMETERS
MIN
MAX
4.90
5.10
4.30
4.50
−−−
1.20
0.05
0.15
0.50
0.75
0.65 BSC
0.18
0.28
0.09
0.20
0.09
0.16
0.19
0.30
0.19
0.25
6.40 BSC
0
8
INCHES
MIN
MAX
0.193 0.200
0.169 0.177
−−− 0.047
0.002 0.006
0.020 0.030
0.026 BSC
0.007
0.011
0.004 0.008
0.004 0.006
0.007 0.012
0.007 0.010
0.252 BSC
0
8
MC74LVXT8051
SOEIAJ−16
M SUFFIX
CASE 966−01
ISSUE O
16
LE
9
Q1
M
E HE
1
8
L
DETAIL P
Z
D
e
VIEW P
A
DIM
A
A1
b
c
D
E
e
HE
L
LE
M
Q1
Z
A1
b
0.13 (0.005)
c
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS D AND E DO NOT INCLUDE MOLD
FLASH OR PROTRUSIONS AND ARE MEASURED
AT THE PARTING LINE. MOLD FLASH OR
PROTRUSIONS SHALL NOT EXCEED 0.15 (0.006)
PER SIDE.
4. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
5. THE LEAD WIDTH DIMENSION (b) DOES NOT
INCLUDE DAMBAR PROTRUSION. ALLOWABLE
DAMBAR PROTRUSION SHALL BE 0.08 (0.003)
TOTAL IN EXCESS OF THE LEAD WIDTH
DIMENSION AT MAXIMUM MATERIAL CONDITION.
DAMBAR CANNOT BE LOCATED ON THE LOWER
RADIUS OR THE FOOT. MINIMUM SPACE
BETWEEN PROTRUSIONS AND ADJACENT LEAD
TO BE 0.46 ( 0.018).
M
0.10 (0.004)
MILLIMETERS
MIN
MAX
−−−
2.05
0.05
0.20
0.35
0.50
0.18
0.27
9.90
10.50
5.10
5.45
1.27 BSC
7.40
8.20
0.50
0.85
1.10
1.50
10 0
0.70
0.90
−−−
0.78
INCHES
MIN
MAX
−−−
0.081
0.002
0.008
0.014
0.020
0.007
0.011
0.390
0.413
0.201
0.215
0.050 BSC
0.291
0.323
0.020
0.033
0.043
0.059
10 0
0.028
0.035
−−−
0.031
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 61312, Phoenix, Arizona 85082−1312 USA
Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada
Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
ON Semiconductor Website: http://onsemi.com
Order Literature: http://www.onsemi.com/litorder
Japan: ON Semiconductor, Japan Customer Focus Center
2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051
Phone: 81−3−5773−3850
http://onsemi.com
12
For additional information, please contact your
local Sales Representative.
MC74LVXT8051/D