VISHAY CH02016

CH
www.vishay.com
Vishay Sfernice
High Frequency 50 GHz Thin Film Chip Resistor
FEATURES
• Operating frequency 50 GHz
• Thin film microwave resistors
• SMD wraparound or flip chip resistor
• Small size, down to 20 mils by 16 mils
• Edged trimmed block resistors
• Pure alumina substrate (99.5 %)
• Ohmic range: 10R to 500R
• Design kits available
• Small internal reactance (LC down to 1 × 10-24)
• Tolerance 1 %, 2 %, 5 %, 10 %
• TCR: 100 ppm/°C in (- 55 °C, + 155 °C) temperature range
• Material categorization: For definitions of compliance
please see www.vishay.com/doc?99912
Those miniaturized components are designed in such a way
that their internal reactance is very small. When correctly
mounted and utilized, they function as almost pure resistors
on a very large range of frequency, up to 50 GHz.
STANDARD ELECTRICAL SPECIFICATIONS
RESISTANCE
RANGE

LIMITING
ELEMENT
VOLTAGE
V
RATED POWER
Pn
W
TOLERANCE
±%
TEMPERATURE
COEFFICIENT
± ppm/°C
MODEL
SIZE
CH02016
02016
10 to 500
0.030
30
1, 2, 5, 10
100
CH0402
0402
10 to 500
0.050
37
1, 2, 5, 10
100
CH0603
0603
10 to 500
0.125
50
1, 2, 5, 10
100
DIMENSIONS in millimeters (inches)
A (1)
A
D
D
D
A
D
C
C
(F)
D
D
E
(P)
B
C
(N) and (G)
E
DIMENSIONS
CASE SIZE
MAX. TOL.
+ 0.1 (+ 0.004)
MIN. TOL.
- 0.1 (- 0.004)
A (1)
B
C
MAX. TOL.
+ 0.1 (+ 0.004)
MIN. TOL.
- 0.1 (- 0.004)
MAX. TOL.
+ 0.1 (+ 0.004)
MIN. TOL.
- 0.1 (- 0.004)
MAX. TOL.
+ 0.127 (+ 0.005)
MIN. TOL.
- 0.127 (- 0.005)
MIN.
MAX.
D/E
02016
0.48 (0.020)
0.39 (0.016)
0.42 (0.02) (2)
0.11 (0.004)
0.15 (0.008)
0402
1.00 (0.040)
0.6 (0.023)
0.5 (0.02)
0.15 (0.006)
0.35 (0.014)
0603
1.52 (0.060)
0.75 (0.030)
0.5 (0.02)
0.25 (0.010)
0.51 (0.020)
Notes
(1) For CH0402 and CH0603 with P termination, A dimension is increased by 0.2 mm
(2) + or - 0.07 mm
Revision: 28-Aug-13
Document Number: 53014
1
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CH
www.vishay.com
Vishay Sfernice
LAND PATTERN FLIP CHIP TERMINATIONS in millimeters
Gmin.
Xmax.
Zmax.
CHIP SIZE
Zmax.
Xmax.
Gmin.
02016
0.53
0.44
0.15
0402
1.4
0.650
0.4
0603
1.71
0.9
0.760
Note
• Suggested land pattern: According to IPC-7351
Dimension and tolerance of land pattern shall be defined by PCB designer; PCB can be designed according to IPC-7351A
“Generic Requirements for Surface Mount Design and Land Pattern Standard”
Example of land pattern: Fabrication allowance, assembly location and min. or max. level density board are not included in the
exemple bellow.
According to IPC-7351A “Generic Requirements for Surface Mount Design and Land Pattern Standard”:
2
2
2
2
2
2
2
2
2
Zmax. = Amin. + 2JT +
 C A + F + P  with C: “Unilateral profile tolerance for the component”;
Gmin. = Fmax. + 2JH -
 C F + F + P  F: ”Unilateral profile tolerance for the board land pattern”;
Xmax. = Bmin. + 2JS +
 C B + F + P  and P: “Diameter of true position placement accuracy to the center of land pattern”.
JH
For rectangular component
suggest:
JS
COMPONENT
Land Pattern Footprint
Flip-Chip mounting, we
JT (TOE)
0 mm
JH (HELL)
0 mm
JS (SDE)
0 mm
JT
WRAPAROUND TERMINATIONS in millimeters
X
m
ax
.
Gmin.
Zmax.
CHIP SIZE
Zmax.
Gmin.
Xmax.
0402
1.55
0.15
0.73
0603
2.37
0.35
0.98
10   R < 50 
50  R < 100 
100  R  500  (1)
5 %, 10 %
2 %, 5 %, 10 %
1 %, 2 %, 5 %, 10 %
TOLERANCE VS. OHMIC VALUES
Ohmic range
Tolerance
Note
(1) Best tolerance for 100  to 500  in 02016 is 2 %
Revision: 28-Aug-13
Document Number: 53014
2
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CH
www.vishay.com
Vishay Sfernice
PREFERRED MODELS AND VALUES
Vishay Sfernice highly recommend to use the smallest sizes and flip chip version to get the best performances.
Recommended Values:
10R/18R/25R/50R/75R/100R/150R/180R/200R/250R/330R/500R
Those values are available with a MOQ of 100 pieces.
Other values can be ordered upon request, but higher MOQ will apply: 1000 pieces for CH02016, 500 pieces for CH0402,
50 pieces for CH0603.
Recommended terminations:
F
Recommended tolerance:
2%
Design kits are available Ex Stock in CH02016 and CH0402 sizes. There are 20 pieces per recommended value. F termination.
5 % tolerance.
Those kits are packaged in pieces of tape and delivered in ESD bags.
PACKAGING
Standard packaging is waffle pack for sizes 0402 and 0603 and plastic tape and reel (low conductivity) for size 02016.
Paper tape and reel is available for size 0402 and either paper tape and reel or plastic tape and reel (low conductivity) for size
0603.
Depending on the type of terminations, parts will be packed differently:
One face:
• Gold terminations: Active face up
• Tin/silver termination: Active face down
Note
• Please refer to Vishay Sfernice Application Note “Guidelines for Vishay Sfernice Resistive and Inductive Products” for soldering
recommendation (document number 52029, 3. Guidelines for Surface Mounting Components (SMD), profile number 3 applies
NUMBER OF PIECES PER PACKAGE
SIZE
02016
0402
0603
MOQ
See MOQ mentioned
on preferred models
and values
WAFFLE PACK
2" X 2"
TAPE AND REEL
TAPE WIDTH
Min.
Max.
100
5000
484
100
8 mm
100
PACKAGING RULES
Waffle Pack
Tape and Reel
Can be filled up to maximum quantity indicated in the table
here above, taking into account the minimum order quantity.
When quantity ordered exceeds maximum quantity of a
single waffle pack, the waffle packs are stacked up on the
top of each other and closed by one single cover. To get
“not stacked up” waffle pack in case of ordered quantity
> maximum number of pieces per package: Please consult
Vishay Sfernice for specific ordering code.
See Part Numbering information to get the quantity desired
by tape.
Revision: 28-Aug-13
Document Number: 53014
3
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CH
www.vishay.com
Vishay Sfernice
GLOBAL PART NUMBER INFORMATION
New Global Part Numbering: CH0402-50RJF (preferred part number format)
C
H
0
4
0
2
-
5
0
R
J
F
T
9
9
9
GLOBAL MODEL
SIZE
OHMIC VALUE
TOLERANCE
TERMINATION (1)
PACKAGING
OPTION
CH
02016
0402
0603
10R to 500R
F=1%
G=2%
J=5%
K = 10 %
F (Flip Chip):
SnAg over nickel barrier
N (W/A):
SnAg over nickel barrier
(except 02016)
P (one face): (2)
Gold bonding pads
G (W/A): Gold
(except 02016)
For more
information see
Codification of
Packaging table
From
1 to 3 digits.
Leave blank
if no option.
Historical Part Number example: CH02016-100RGFPT1K (tapes of 1K pieces)
CH0402-50RJF
(waffle pack)
Note
• Historical part numbers are not recommended but can still be used for ordering.
CODIFICATION OF PACKAGING
WAFFLE PACK (standard packaging for CH0402 and CH0603)
W
10 min., 1 mult
PLASTIC TAPE (standard packaging for CH02016 and CH0603)
T
100 min., 1 mult
TA
100 min., 100 mult
TB
250 min., 250 mult
TC
500 min., 500 mult
TD
1000 min., 1000 mult
TE
2500 min., 2500 mult
TF
Full tape (qunatity depending on size of chips)
PAPER TAPE (standard packaging for CH0402 - available for CH0603)
PT
100 min., 1 mult
PA
100 min., 100 mult
PB
250 min., 250 mult
PC
500 min., 500 mult
PD
1000 min., 1000 mult
PE
2500 min., 2500 mult
PF
Full tape (qunatity depending on size of chips)
TYPICAL HIGH FREQUENCY PERFORMANCE ELECTRICAL MODEL
Z
C
Z0
Z0
Lc
Lc
L
C
L
R
Z
Lc
Cg
Cg
R
Internal shunt capacitance
Internal inductance
Resistance
Internal impedance (R, L, C)
External connection inductance
External capacitance to ground
Revision: 28-Aug-13
Document Number: 53014
4
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CH
www.vishay.com
Vishay Sfernice
The complex impedance of the chip resistor is given by the following equations:
2
2
2
R + j  L – R C – L C 
Z = ------------------------------------------------------------------------------------2
2
2
4
1 + C   R C – 2L  + L C 
Z
1
-------- = ------------------------------------------------------------------------------------------ x
2
2
2
4
R
1 + C   R C – 2L  + L C 
2
2
2
  L – R C – L C 
1 + -----------------------------------------------------------R
2
2
2
2
– 1   L – R C – L C 
 = tan -----------------------------------------------------------R
Notes
• =2xxf
• f: Frequency
L
The chip resistor itself is purely resistive when R = ---- . The smaller the L x C product the greater the frequency range over
C
which the resistor looks approximately resistive.
Z
This can be seen on the graphs showing the ratio -------- versus frequency.
R
R, L and C are relevant to the chip resistor itself.
Lc and Cg also depends on the way the chip resistor is mounted.
It is important to notice that after assembly the external reactance of Lc and Cg will be combined to internal reactance of L and
C. This combination can upgrade or downgrade the HF behaviour of the component.
This is why we are displaying two sets of data:
Z
• -------- versus frequency curves which aims to show at a glance the intrinsic HF performance of a given chip resistor
R
• S-parameters versus frequency curves relevant to chip resistor when assembled on ideal Z0 impedance transmission line
These lines are terminated with adapted source and load impedance respectively Zs and Zl with Z0 = ZL = Zs (for others
configurations please consult us).
Equivalent circuit for S-parameters:
Z total
C
ZS
G
Z0
Z0
Cg
Lc
Lc
L
Cg
ZL
R
S-parameters are computed taking into account all the resistive, inductive and capacitive elements (Z total) and Z0 = ZL = Zs = R.
Revision: 28-Aug-13
Document Number: 53014
5
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CH
www.vishay.com
Vishay Sfernice
INTERNAL IMPEDANCE CURVES
1.1
10 Ω
25 Ω
50 Ω
75 Ω
1.0
0.9
100 Ω
0.8
150 Ω
IZI/R
0.7
200 Ω
0.6
250 Ω
0.5
0.4
500 Ω
0.3
0.2
0.1
0.1
1
10
100
f (GHz)
Internal impedance curve for 02016 size (F and P terminations)
1.1
10 Ω
25 Ω
1.0
50 Ω
0.9
75 Ω
0.8
100 Ω
IZI/R
0.7
150 Ω
0.6
200 Ω
0.5
250 Ω
0.4
0.3
500 Ω
0.2
0.1
0.1
1
10
100
f (GHz)
Internal impedance curve for 0402 size (F and P terminations)
Revision: 28-Aug-13
Document Number: 53014
6
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CH
www.vishay.com
Vishay Sfernice
INTERNAL IMPEDANCE CURVES
1.1
10 Ω
25 Ω
50 Ω
75 Ω
1.0
0.9
0.8
100 Ω
IZI/R
0.7
0.6
0.5
150 Ω
0.4
200 Ω
0.3
250 Ω
0.2
500 Ω
0.1
0.1
1
10
100
f (GHz)
Internal impedance curve for 0402 size (N and G terminations)
1.1
10 Ω
25 Ω
1.0
50 Ω
0.9
0.8
75 Ω
IZI/R
0.7
100 Ω
0.6
0.5
150 Ω
0.4
200 Ω
250 Ω
0.3
0.2
500 Ω
0.1
0.1
1
10
100
f (GHz)
Internal impedance curve for 0603 size (F and P terminations)
Revision: 28-Aug-13
Document Number: 53014
7
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CH
www.vishay.com
Vishay Sfernice
INTERNAL IMPEDANCE CURVES
1.1
10 Ω
25 Ω
50 Ω
1.0
75 Ω
0.9
0.8
IZI/R
0.7
100 Ω
0.6
0.5
150 Ω
0.4
200 Ω
0.3
250 Ω
0.2
500 Ω
0.1
0.1
1
10
100
f (GHz)
Internal impedance curve for 0603 size (N and G terminations)
S-PARAMETER
CH02016 (F and P Terminations)
-2
-2
-3
-3
S21
S21
-4
Magnitude (dB)
Magnitude (dB)
-4
-5
-6
-7
-8
-5
-6
-7
S11
-8
-9
-9
S11
- 10
0.1
1
10
100
- 10
0.1
1
10
f (GHz)
f (GHz)
CH02016 flip chip (Z0 = ZI = Zs = R = 50 Ω)
CH02016 flip chip (Z0 = ZI = Zs = R = 100 Ω)
Revision: 28-Aug-13
100
Document Number: 53014
8
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CH
www.vishay.com
Vishay Sfernice
S-PARAMETER
CH0402 (F and P Terminations)
-2
-2
-3
-3
S21
-4
S21
-5
-6
-7
S11
Magnitude (dB)
Magnitude (dB)
-4
-5
-6
-7
-8
-8
-9
-9
- 10
0.1
1
10
100
- 10
0.1
S11
1
10
f (GHz)
f (GHz)
CH0402 flip chip (Z0 = ZI = Zs = R = 50 Ω)
CH0402 flip chip (Z0 = ZI = Zs = R = 100 Ω)
100
CH0402 (N and G Terminations)
-2
-2
-3
-3
-4
-4
S21
Magnitude (dB)
Magnitude (dB)
S21
-5
-6
S11
-7
-5
-6
-7
S11
-8
-8
-9
-9
- 10
0.1
1
10
100
- 10
0.1
1
10
f (GHz)
f (GHz)
CH0402 wraparound (Z0 = ZI = Zs = R = 50 Ω)
CH0402 wraparound (Z0 = ZI = Zs = R = 100 Ω)
100
CH0603 (F and P Terminations)
-2
-2
-3
-3
-4
-4
-5
S21
-6
-7
Magnitude (dB)
Magnitude (dB)
S11
S21
-5
-6
-7
-8
-8
-9
-9
- 10
0.1
1
10
100
- 10
0.1
S11
1
10
f (GHz)
f (GHz)
CH0603 flip chip (Z0 = ZI = Zs = R = 50 Ω)
CH0603 flip chip (Z0 = ZI = Zs = R = 100 Ω)
Revision: 28-Aug-13
100
Document Number: 53014
9
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CH
www.vishay.com
Vishay Sfernice
S-PARAMETER
CH0603 (N and G Terminations)
-2
-2
-3
-3
-4
-4
Magnitude (dB)
Magnitude (dB)
S11
-5
-6
-7
-8
-5
S21
-6
S11
-7
-8
S21
-9
- 10
0.1
1
10
100
-9
- 10
0.1
1
10
f (GHz)
f (GHz)
CH0603 wraparound (Z0 = ZI = Zs = R = 50 Ω)
CH0603 wraparound (Z0 = ZI = Zs = R = 100 Ω)
Revision: 28-Aug-13
100
Document Number: 53014
10
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000