FUJITSU SEMICONDUCTOR DATA SHEET DS07-12535-2E 8-bit Proprietary Microcontroller CMOS F2MC-8L MB89850R Series MB89855R/P857/W857 ■ DESCRIPTION The MB89850R series has been developed as a general-purpose version of the F2MC*-8L family consisting of proprietary 8-bit, single-chip microcontrollers. In addition to the F2MC-8L CPU core which can operate at low voltage but at high speed, the microcontrollers contain a variety of peripheral functions such as a timer unit, PWM timers, a UART, a serial interface, a 10-bit A/D converter, and an external interrupt. The MB89850R series is applicable to a wide range of applications from consumer products to industrial equipment, including portable devices. *: F2MC stands for FUJITSU Flexible Microcontroller. ■ FEATURES • Various package options SDIP package (64 pins)/QFP package (64 pins) • High-speed processing at low voltage Minimum execution time: 0.4 µs/3.5 V, 0.8 µs/2.7 V (Continued) ■ PACKAGE 64-pin Plastic SH-DIP 64-pin Plastic QFP 64-pin Ceramic SH-DIP 64-pin Ceramic QFP (DIP-64P-M01) (FPT-64P-M06) (DIP-64C-A06) (FPT-64C-A02) (DIP-64P-M01) (FPT-64P-M06) (DIP-64C-A06) (FPT-64C-A02) MB89850R Series (Continued) • F2MC-8L family CPU core Instruction set optimized for controllers Multiplication and division instructions 16-bit arithmetic operations Test and branch instructions Bit manipulation instructions, etc. • 8-bit PWM timers: 2 channels Also usable as a reload timer • UART Full-duplex double buffer Synchronous and asynchronous data transfer • 8-bit serial I/O Switchable transfer direction allows communication with various equipment. • 10-bit A/D converter Conversion time: 13.2 µs Activation by an external input or a timer unit capable • External interrupt: 4 channels Four channels are independent and capable of wake-up from low-power consumption modes (with an edge detection function). • Low-power consumption modes Stop mode (Oscillation stops to minimize the current consumption.) Sleep mode (The CPU stops to reduce the current consumption to approx. 1/3 of normal.) • Bus interface functions Including hold and ready functions • Timer unit Outputs non-overlap three-phase waveforms to control an AC inverter motor. Also usable as a PWM timer (4 channels) 2 MB89850R Series ■ PRODUCT LINEUP Part number Parameter Classification MB89P857 MB89W857 MB89855R Mass production products (mask ROM products) ROM size 16 K × 8 bits (internal mask ROM) RAM size 512 × 8 bits One-time PROM pruducts/EPROM products, also used for evaluation 32 K × 8 bits (internal PROM, programming with general-purpose EPROM programmer) 1 K × 8 bits CPU functions Number of instructions: Instruction bit length: Instruction length: Data bit length: Minimum execution time: Interrupt processing time: 136 8 bits 1 to 3 bytes 1, 8, 16 bits 0.4 µs/10 MHz 3.6 µs/10 MHz Ports Input ports: Output ports (N-ch open drain): Output ports (CMOS): I/O ports (CMOS): Total: 5 (All also serve as peripherals) 8 (All also serve as peripherals) 8 (All also serve as bus control pins) 32 (All also serve as bus pins or peripherals) 53 Timer unit 8-bit PWM timer 1, 8-bit PWM timer 2 UART 8-bit serial I/O 10-bit up/down count timer × 1 Compare registers with buffer × 4 Compare timer unit clear register with buffer × 1 Zero detection pin control 4 output channels Non-overlap three-phase waveform output Independent three-phase dead-time timer 8-bit reload timer operation (toggled output capable, operating clock cycle: 0.4 µs to 25.6 µs) 8-bit resolution PWM operation (conversion cycle: 102 µs to 6.528 ms) 8 bits Clock synchronous/asynchronous data transfer capable 8 bits LSB first/MSB first selectability One clock selectable from four transfer clocks (one external shift clock, three internal shift clocks: 0.8 µs, 3.2 µs, 12.8 µs) 10-bit resolution × 8 channels A/D conversion time: 13.2 µs 10-bit A/D converter Continous activation by a compare channel 0 in timer unit or an external activation capable External interrupt 4 independent channels (edge selection, interrupt vector, source flag) Rising edge/falling edge selectability. Used also for wake-up from stop/sleep mode. (Edge detection is also permitted in stop mode.) Standby modes Sleep mode, stop mode Process Operating voltage* CMOS 2.7 V to 6.0 V 2.7 V to 5.5 V * : Varies with conditions such as the operating frequency. (See section “■ Electrical Characteristics.”) 3 MB89850R Series ■ PACKAGE AND CORRESPONDING PRODUCTS Package MB89855R MB89P857 MB89W857 × DIP-64P-M01 × DIP-64C-A06 × × FPT-64P-M06 × FPT-64C-A02 : Available × × : Not available Note: For more information about each package, see section “■ Package Dimensions.” ■ DIFFERENCES AMONG PRODUCTS 1. Memory Size Before evaluating using the OTPROM (one-time PROM) products (also used for evaluation), verify its differences from the product that will actually be used. Take particular care on the following point: • The stack area, etc., is set at the upper limit of the RAM. 2. Current Consumption When operated at low speed, the product with an OTPROM or an EPROM will consume more current than the product with a mask ROM. However, the current consumption in sleep/stop modes is the same. 3. Mask Options In the MB89P857/W857, no option can be set. Before using options check section “■ Mask Options.” Take particular care on the following point: • A pull-up resistor can be set for P00 to P07, P10 to P17 and P20 to P27 only at single-chip mode. 4 MB89850R Series ■ PIN ASSIGNMENT (Top view) P31/SO1 P30/SCK1 P47/TRGI P46/Z P45/Y P44/X P43/RTO3/W P42/RTO2/V P41/RTO1/U P40/RTO0 P50/AN0 P51/AN1 P52/AN2 P53/AN3 P54/AN4 P55/AN5 P56/AN6 P57/AN7 AVCC AVR AVSS P64/DTTI P63/INT3/ADST P62/INT2 P61/INT1 P60/INT0 RST MOD0 MOD1 X0 X1 VSS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 VCC P32/SI1 P33/SCK2 P34/SO2 P35/SI2 P36/PTO1 P37/PTO2 VSS P00/AD0 P01/AD1 P02/AD2 P03/AD3 P04/AD4 P05/AD5 P06/AD6 P07/AD7 P10/A08 P11/A09 P12/A10 P13/A11 P14/A12 P15/A13 P16/A14 P17/A15 P20/BUFC P21/HAK P22/HRQ P23/RDY P24/CLK P25/WR P26/RD P27/ALE (DIP-64P-M01) (DIP-64C-A06) 5 MB89850R Series 64 63 62 61 60 59 58 57 56 55 54 53 52 P43/RT03/W P44/X P45/Y P46/Z P47/TRGI P30/SCKI P31/SOI VCC P32/SI1 P33/SCK2 P34/SO2 P35/SI2 P36/PTO1 (Top view) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 RST MOD0 MOD1 X0 X1 VSS P27/ALE P26/RD P25/WR P24/CLK P23/RDY P22/HRQ P21/HAK 20 21 22 23 24 25 26 27 28 29 30 31 32 P42/RTO2/V P41/RTO1/U P40/RTO0 P50/AN0 P51/AN1 P52/AN2 P53/AN3 P54/AN4 P55/AN5 P56/AN6 P57/AN7 AVCC AVR AVSS P64/DTTI P63/INT3/ADST P62/INT2 P61/INT1 P60/INT0 (FPT-64P-M06) (FPT-64C-A02) 6 P37/PTO2 VSS P00/AD0 P01/AD1 P02/AD2 P03/AD3 P04/AD4 P05/AD5 P06/AD6 P07/AD7 P10/A08 P11/A09 P12/A10 P13/A11 P14/A12 P15/A13 P16/A14 P17/A15 P20/BUFC MB89850R Series ■ PIN DESCRIPTION Pin no. SH-DIP *1 *2 QFP Pin name 30 23 X0 31 24 X1 28 21 MOD0 29 22 MOD1 27 20 56 to 49 Circuit type Function A Crystal oscillator pins (10 MHz) B Operating mode selection pins Connect directly to VCC or VSS. RST C Reset I/O pin This pin is an N-ch open-drain output type with a pull-up resistor, and a hysteresis input type. “L” is output from this pin by an internal reset source. The internal circuit is initialized by the input of “L”. 49 to 42 P00/AD0 to P07/AD7 D General-purpose I/O ports When an external bus is used, these ports function as multiplex pins of lower address output and data I/O. 48 to 41 41 to 34 P10/A08 to P17/A15 D General-purpose I/O ports When an external bus is used, these ports function as upper address output. 40 33 P20/BUFC F General-purpose output port When an external bus is used, this port can also be used as a buffer control output. 39 32 P21/HAK F General-purpose output port When an external bus is used, this port can also be used as a hold acknowledge output. 38 31 P22/HRQ D General-purpose output port When an external bus is used, this port can also be used as a hold request input. 37 30 P23/RDY D General-purpose output port When an external bus is used, this port functions as a ready input. 36 29 P24/CLK F General-purpose output port When an external bus is used, this port functions as a clock output. 35 28 P25/WR F General-purpose output port When an external bus is used, this port functions as a write signal output. 34 27 P26/RD F General-purpose output port When an external bus is used, this port functions as a read signal output. 33 26 P27/ALE F General-purpose output port When an external bus is used, this port functions as an address latch signal output. 2 59 P30/SCK1 E General-purpose I/O port Also serves as the clock I/O for the UART. This port is a hysteresis input type. *1: DIP-64P-M01, DIP-64C-A06 *2: FPT-64P-M06, FPT-64C-A02 (Continued) 7 MB89850R Series (Continued) Pin no. Pin name Function QFP*2 1 58 P31/SO1 E General-purpose I/O port Also serves as the data output for the UART. This port is a hysteresis input type. 63 56 P32/SI1 E General-purpose I/O port Also serves as the data input for the UART. This port is a hysteresis input type. 62 55 P33/SCK2 E General-purpose I/O port Also serves as the clock I/O for the 8-bit serial I/O. This port is a hysteresis input type. 61 54 P34/SO2 E General-purpose I/O port Also serves as the data output for the 8-bit serial I/O. This port is a hysteresis input type. 60 53 P35/SI2 E General-purpose I/O port Also serves as the data input for the 8-bit serial I/O. This port is a hysteresis input type. 59 52 P36/PTO1 E General-purpose I/O port Also serves as the pulse output for the 8-bit PWM timer 1. This port is a hysteresis input type. 58 51 P37/PTO2 E General-purpose I/O port Also serves as the pulse output for the 8-bit PWM timer 2. This port is a hysteresis input type. 10 3 P40/RTO0 E General-purpose I/O port Also serves as the pulse output for the timer unit. This port is a hystereisis input type. 9, 8, 7 2, 1, 64 P41/RTO1/U, P42/RTO2/V, P43/RTO3/W E General-purpose I/O ports Also serve as the pulse output or non-overlap threephase waveform output for the timer unit. These ports are a hysteresis input type. 6, 5, 4 63, 62, 61 P44/X, P45/Y, P46/Z E General-purpose I/O ports Also serve as a non-overlap three-phase waveform output. These ports are a hysteresis input type. 3 60 P47/TRGI E General-purpose I/O port Also serves as the trigger input for the timer unit. This port is a hysteresis input type. 11 to 18 4 to 11 P50/AN0 to P57/AN7 G N-ch open-drain output ports Also serve as the analog input for the A/D converter. 26 to 24 19 to 17 P60/INT0 to P62/INT2 H General-purpose input ports Also serve as an external interrupt input. These ports are a hysteresis input type. 23 16 P63/INT3/ ADST H General-purpose input port Also serves as an external interrupt input and as the activation trigger input for the A/D converter. This port is a hysteresis input type. *1: DIP-64P-M01, DIP-64C-A06 *2: FPT-64P-M06, FPT-64C-A02 8 Circuit type SH-DIP*1 (Continued) MB89850R Series (Continued) Pin no. Pin name Circuit type Function SH-DIP*1 QFP*2 22 15 P64/DTTI H General-purpose input port Also serves as a dead-time timer disable input. This port is a hysteresis input type. DTTI input is with a noise canceller. 64 57 VCC — Power supply pin 32, 57 25, 50 VSS — Power supply (GND) pins 19 12 AVCC — A/D converter power supply pin 20 13 AVR — A/D converter reference voltage input pin 21 14 AVSS — A/D converter power supply (GND) pin Use this pin at the same voltage as VSS. *1: DIP-64P-M01, DIP-64C-A06 *2: FPT-64P-M06, FPT-64C-A02 9 MB89850R Series ■ I/O CIRCUIT TYPE Type Circuit A Remarks • At an oscillation feedback resistor of approximately 1 MΩ/5.0 V X1 X0 Standby control signal B C • At an output pull-up resistor (P-ch) of approximately 50 kΩ/5.0 V • Hysteresis input R P-ch N-ch D R P-ch P-ch • • • • CMOS output CMOS input Pull-up resistor optional (Mask ROM products) At a pull-up resistor of approximately 50 kΩ/5.0 V • • • • CMOS output Hysteresis input Pull-up resistor optional (Mask ROM products) At a pull-up resistor of approximately 50 kΩ/5.0 V N-ch E R P-ch P-ch N-ch (Continued) 10 MB89850R Series (Continued) Type Circuit Remarks F R P-ch P-ch • CMOS output • Pull-up resistor optional (Mask ROM products) • At a pull-up resistor of approximately 50 kΩ/5.0 V N-ch G • N-ch open-drain output • Analog input N-ch Analog input H R • Hysteresis input • Pull-up resistor optional (Mask ROM products) • At a pull-up resistor of approximately 50 kΩ/5.0 V 11 MB89850R Series ■ HANDLING DEVICES 1. Preventing Latchup Latchup may occur on CMOS ICs if voltage higher than VCC or lower than VSS is applied to input and output pins other than medium- and high-voltage pins or if higher than the voltage which shows on “1. Absolute Maximum Ratings” in section “■ Electrical Characteristics” is applied between VCC and VSS. When latchup occurs, power supply current increases rapidly and might thermally damage elements. When using, take great care not to exceed the absolute maximum ratings. Also, take care to prevent the analog power supply (AVCC and AVR) and analog input from exceeding the digital power supply (VCC) when the analog system power supply is turned on and off. 2. Treatment of Unused Input Pins Leaving unused input pins open could cause malfunctions. They should be connected to a pull-up or pull-down resistor. 3. Treatment of Power Supply Pins on Microcontrollers with A/D and D/A Converters Connect to be AVCC = DAVC = VCC and AVSS = AVR = VSS even if the A/D and D/A converters are not in use. 4. Treatment of N.C. Pin Be sure to leave (internally connected) N.C. pin open. 5. Power Supply Voltage Fluctuations Although VCC power supply voltage is assured to operate within the rated range, a rapid fluctuation of the voltage could cause malfunctions, even if it occurs within the rated range. Stabilizing voltage supplied to the IC is therefore important. As stabilization guidelines, it is recommended to control power so that VCC ripple fluctuations (P-P value) will be less than 10% of the standard VCC value at the commercial frequency (50 to 60 Hz) and the transient fluctuation rate will be less than 0.1 V/ms at the time of a momentary fluctuation such as when power is switched. 6. Precautions when Using an External Clock Even when an external clock is used, oscillation stabilization time is required for power-on reset (optional) and wake-up from stop mode. 12 MB89850R Series ■ PROGRAMMING TO THE EPROM ON THE MB89P857/W857 The MB89P857/W857 are an OTPROM version of the MB89850R series. 1. Features • 32-Kbyte PROM on chip • Equivalency to the MBM27C256A in EPROM mode (when programmed with the EPROM programmer) 2. Memory Space Memory space in EPROM mode is diagrammed below. Address Single chip 0000H EPROM mode ( Corresponding addresses on the EPROM programmer) I/O 0080H RAM 0480H Not available 8000H 0000H PROM 32 KB FFFFH EPROM 32 KB 7FFFH 3. Programming to the EPROM In EPROM mode, the MB89P857/W857 functions equivalent to the MBM27C256A. This allows the PROM to be programmed with a general-purpose EPROM programmer (the electronic signature mode cannot be used) by using the dedicated socket adapter. • Programming procedure (1) Set the EPROM programmer to the MBM27C256A. (2) Load program data into the EPROM programmer at 0000H to 7FFFH (note that addresses 8000H to FFFFH while operating as a single chip assign to addresses 0000H to 7FFFH in EPROM mode.) (3) Program to 0000H to 7FFFH with the EPROM programmer. 13 MB89850R Series 4. Recommended Screening Conditions High-temperature aging is recommended as the pre-assembly screening procedure for a product with a blanked OTPROM microcomputer program. Program, verify Aging +150°C, 48 Hrs. Data verification Assembly 5. Programming Yield All bits cannot be programmed at Fujitsu shipping test to a blanked OTPROM microcomputer, due to its nature. For this reason, a programming yield of 100% cannot be assured at all times. 6. Erasure In order to clear all locations of their programmed contents, it is necessary to expose the internal EPROM to an ultraviolet light source. A dosage of 10 W-seconds/cm2 is required to completely erase an internal EPROM. This dosage can be obtained by exposure to an ultraviolet lamp (wavelength of 2537 Angstroms (Å)) with intensity of 12000 µW/cm2 for 15 to 21 minutes. The internal EPROM should be about one inch from the source and all filters should be removed from the UV light source prior to erasure. It is important to note that the internal EPROM and similar devices, will erase with light sources having wavelengths shorter than 4000 Å. Although erasure time will be much longer than with UV source at 2537 Å, nevertheless the exposure to fluorescent light and sunlight will eventually erase the internal EPROM, and exposure to them should be prevented to realize maximum system reliability. If used in such an environment, the package windows should be covered by an opaque label or substance. 7. EPROM Programmer Socket Adapter Package Compatible socket adapter DIP-64P-M01 ROM-64SD-28DP-8L* FPT-64P-M06 ROM-64QF-28DP-8L FPT-64P-A02 ROM-64QF-28DP-8L5 * : Connect the adapter jumper pin to VSS when using. Inquiry: Sun Hayato Co., Ltd.: Fax 81-3-5396-9106 14 MB89850R Series ■ BLOCK DIAGRAM Timebase timer Oscillator Clock controller Reset circuit (WDT) RST MOD0 MOD1 P36/PTO1 8-bit serial I/O P35/SI2 P34/SO2 P33/SCK2 External bus interface P32/SI1 P31/SO1 P30/SCK1 UART CMOS I/O port CMOS I/O port Port 2 P27/ALE P26/RD P25/WR P24/CLK P23/RDY P22/HRQ P21/HAK P20/BUFC 8-bit PWM timer 1 6 P47/TRGI P46/Z P45/Y P44/X P43/RTO3/W P42/RTO2/V P41/RTO1/U P40/RTO0 Port 4 8 Internal bus P10/A08 to P17/A15 8 P37/PTO2 CMOS I/O port Ports 0 and 1 P00/AD0 to P07/AD7 8-bit PWM timer 2 Port 3 X0 X1 Timer unit CMOS output port (Dead-time timer) 4 RAM External interrupt Port 6 P64/DTTI 3 P60/INT0 to P62/INT2 P63/INT3/ADST F2MC-8L Input port CPU AVR AVCC AVSS 8 Other pins VCC , VSS × 2 Part number MB89855R MB89W857/P857 10-bit A/D converter RAM size ROM size 512 bytes 16 Kbytes 1 Kbyte 32 Kbytes (EPROM) Port 5 ROM 8 P50/AN0 to P57/AN7 N-ch open-drain output port 15 MB89850R Series ■ CPU CORE 1. Memory Space The microcontrollers of the MB89850R series offer a memory space of 64 Kbytes for storing all of I/O, data, and program areas. The I/O area is located at the lowest address. The data area is provided immediately above the I/O area. The data area can be divided into register, stack, and direct areas according to the application. The program area is located at exactly the opposite end, that is, near the highest address. Provide the tables of interrupt reset vectors and vector call instructions toward the highest address within the program area. The memory space of the MB89860/850 series is structured as illustrated below. • Memory Space MB89W857/P857 MB89855R 0000H 0000H I/O 0080H I/O 0080H RAM 512 B RAM 1 KB 0100H 0100H Register Register 0200H 0200H 0280H 0480H External area External area 8000H C000H ROM* 32 KB ROM* 16 KB FFFFH FFFF H *: The ROM area is an external area depending on the mode. 16 MB89850R Series 2. Registers The F2MC-8L family has two types of registers; dedicated registers in the CPU and general-purpose registers in the memory. The following dedicated registers are provided: Program counter (PC): A 16-bit register for indicating instruction storage positions Accumulator (A): A 16-bit temporary register for storing arithmetic operations, etc. When the instruction is an 8-bit data processing instruction, the lower byte is used. Temporary accumulator (T): A 16-bit register which performs arithmetic operations with the accumulator When the instruction is an 8-bit data processing instruction, the lower byte is used. Index register (IX): A 16-bit register for index modification Extra pointer (EP): A 16-bit pointer for indicating a memory address Stack pointer (SP): A 16-bit register for indicating a stack area Program status (PS): A 16-bit register for storing a register pointer, a condition code Initial value 16 bits FFFDH : Program counter PC A : Accumulator T : Temporary accumulator Indeterminate IX : Index register Indeterminate EP : Extra pointer Indeterminate SP : Stack pointer Indeterminate PS : Program status Indeterminate I-flag = 0, IL1, 0 = 11 Other bits are indeterminate. The PS can further be divided into higher 8 bits for use as a register bank pointer (RP) and the lower 8 bits for use as a condition code register (CCR). (See the diagram below.) • Structure of the Program Status Register 15 PS 14 13 12 RP 11 10 9 8 Vacancy Vacancy Vacancy RP 7 6 H I 5 4 IL1, 0 3 2 1 0 N Z V C CCR 17 MB89850R Series The RP indicates the address of the register bank currently in use. The relationship between the pointer contents and the actual address is based on the conversion rule illustrated below. • Rule for Conversion of Actual Addresses of the General-purpose Register Area RP Lower OP codes “0” “0” “0” “0” “0” “0” “0” “1” R4 R3 R2 R1 R0 b2 ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ b1 b0 ↓ ↓ Generated addresses A15 A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 The CCR consists of bits indicating the results of arithmetic operations and the contents of transfer data and bits for control of CPU operations at the time of an interrupt. H-flag: Set when a carry or a borrow from bit 3 to bit 4 occurs as a result of an arithmetic operation. Cleared otherwise. This flag is for decimal adjustment instructions. I-flag: Interrupt is allowed when this flag is set to 1. Interrupt is prohibited when the flag is set to 0. Set to 0 when reset. IL1, 0: Indicates the level of the interrupt currently allowed. Processes an interrupt only if its request level is higher than the value indicated by this bit. IL1 IL0 Interrupt level 0 0 0 1 1 0 2 1 1 3 1 High-low High Low = no interrupt N-flag: Set if the MSB is set to 1 as the result of an arithmetic operation. Cleared when the bit is set to 0. Z-flag: Set when an arithmetic operation results in 0. Cleared otherwise. V-flag: Set if the complement on 2 overflows as a result of an arithmetic operation. Reset if the overflow does not occur. C-flag: Set when a carry or a borrow from bit 7 occurs as a result of an arithmetic operation. Cleared otherwise. Set to the shift-out value in the case of a shift instruction. 18 MB89850R Series The following general-purpose registers are provided: General-purpose registers: An 8-bit register for storing data The general-purpose registers are 8 bits and located in the register banks of the memory. One bank contains eight registers and up to a total of 32 banks can be used on the MB89850R series. The bank currently in use is indicated by the register bank pointer (RP). Note: The number of register banks that can be used varies with the RAM size. • Register Bank Configuration This address = 0100H + 8 × (RP) R0 R1 R2 R3 R4 R5 R6 R7 32 banks Memory area 19 MB89850R Series ■ I/O MAP Address Read/write Register name Register description 00H (R/W) PDR0 Port 0 data register 01H (W) DDR0 Port 0 data direction register 02H (R/W) PDR1 Port 1 data register 03H (W) DDR1 Port 1 data direction register 04H (R/W) PDR2 Port 2 data register 05H (W) BCTR External bus pin control register 06H Vacancy 07H Vacancy 08H (R/W) STBC Standby control register 09H (W) WDTC Watchdog timer control register 0AH (R/W) TBTC Timebase timer control register Vacancy 0BH 0CH (R/W) PDR3 Port 3 data register 0DH (W) DDR3 Port 3 data direction register 0EH (R/W) PDR4 Port 4 data register 0FH (W) DDR4 Port 4 data direction register 10H (R/W) PDR5 Port 5 data register 11H 12H Vacancy (R) PDR6 13H 14H Vacancy (R/W) PDR7 Port 7 data register Vacancy 15H 16H Port 6 data register (R/W) PDR8 17H to 1BH Port 8 data register Vacancy 1CH (R/W) CTR1 PWM control register 1 1DH (W) CMR1 PWM compare register 1 1EH (R/W) CTR2 PWM control register 2 1FH (W) CMR2 PWM compare register 2 20H (R/W) SMC UART serial mode control register 21H (R/W) SRC UART serial rate control register 22H (R/W) SSD UART serial status/data register 23H (R/W) SIDR/SODR 24H (R/W) SMR Serial mode register 25H (R/W) SDR Serial data register UART serial data register (Continued) 20 MB89850R Series (Continued) Address Read/write Register name Register description 26H (R/W) EIC1 External interrupt control register 1 27H (R/W) EIC2 External interrupt control register 2 28H (R/W) ADC1 A/D converter control register 1 29H (R/W) ADC2 A/D converter control register 2 2AH (R) ADDH A/D converter data register (H) 2BH (R) ADDL A/D converter data register (L) Vacancy 2CH 2DH (W) ZOCTR 2EH (W) CLRBRH Compare clear buffer register (H) 2FH (W) CLRBRL Compare clear buffer register (L) 30H (R/W) TCSR Timer control status register 31H (R/W) CICR Compare interrupt control register 32H (R/W) TMCR Timer mode control register 33H (R/W) COER Compare/port selection register 34H (R/W) CMCR Compare buffer mode control register 35H (R/W) DTCR Dead-time timer control register 36H (W) DTSR Dead-time setting register 37H (R/W) OCTBR 38H (W) OCPBR0H Output compare buffer register 0 (H) 39H (W) OCPBR0L Output compare buffer register 0 (L) 3AH (W) OCPBR1H Output compare buffer register 1 (H) 3BH (W) OCPBR1L Output compare buffer register 1 (L) 3CH (W) OCPBR2H Output compare buffer register 2 (H) 3DH (W) OCPBR2L Output compare buffer register 2 (L) 3EH (W) OCPBR3H Output compare buffer register 3 (H) 3FH (W) OCPBR3L Output compare buffer register 3 (L) 40H to 7BH Zero detection output control register Output control buffer register Vacancy 7CH (W) ILR1 Interrupt level setting register 1 7DH (W) ILR2 Interrupt level setting register 2 7EH (W) ILR3 Interrupt level setting register 3 7FH Vacancy Notes: • Do not use vacancies. • When a read-modify-write instruction (such as bit set) is used to access a write-only register or a register containing a write-only bit, a bit designated by the instruction will have a predetermined value. However, a write-only bit included, if any, in bits not defined by the instruction will cause a malfunction. So no access to the register should be tried with any read-modefy-write instruction. 21 MB89850R Series ■ ELECTRICAL CHARACTERISTICS 1. Absolute Maximum Ratings (AVSS = VSS = 0.0 V) Parameter Symbol Value Unit Remarks Min. Max. VCC AVCC VSS – 0.3 VSS + 7.0 V * A/D converter reference input voltage AVR VSS – 0.3 VSS + 7.0 V AVR must not exceed AVCC + 0.3 V. Program voltage VPP VSS – 0.3 13.0 V MOD1 pins of MB89P857/ W857 Input voltage VI VSS – 0.3 VCC + 0.3 V Output voltage VO VSS – 0.3 VSS + 0.3 V “L” level maximum output current IOL — 20 mA IOLAV1 — 4 mA P00 to P07, P10 to P17, P20 to P27, P30 to P37, P50 to P57 IOLAV2 — 15 mA P40 to P47 ΣIOLAV1 — 30 mA P00 to P07, P10 to P17, P20 to P27, P30 to P37, P50 to P57 ΣIOLAV2 — 50 mA P40 to P47 “H” level maximum output current IOH — –20 mA “H” level average output current IOHAV — –4 mA “H” level total maximum output current ΣIOH — –20 mA Power consumption PD — 300 mW Operating temperature TA –40 +85 °C Storage temperature Tstg –55 +150 °C Power supply voltage “L” level average output current “L” level total average output current *: Use AVCC and VCC set at the same voltage. Take care so that AVCC does not exceed VCC, such as when power is turned on. WARNING: Permanent device damage may occur if the above “Absolute Maximum Ratings” are exceeded. Functional operation should be restricted to the conditions as detailed in the operational sections of this data sheet. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 22 MB89850R Series 2. Recommended Operating Conditions (AVSS = VSS = 0.0 V) Parameter Value Symbol VCC AVCC Power supply voltage Unit Remarks 6.0* V Normal operation assurance range* MB89855R 2.7* 5.5* V Normal operation assurance range* MB89P857/W855 1.5 6.0 V Retains the RAM state in stop mode Min. Max. 2.7* A/D converter reference input voltage AVR 0.0 AVCC V Operating temperature TA –40 +85 °C *: These values vary with the operating frequency, instruction cycle, and analog assurance range. See Figure 1 and “5. A/D Converter Electrical Characteristics.” Note: Connect the MOD0 and MOD1 pins to VCC or VSS. 6 5.5 Analog accuracy assured in the VCC = AVCC = 3.5 V to 6.0 V range 5 Operating voltage (V) Operation assurance range 4 3 2 1 1 2 3 4 5 6 7 8 9 10 Clock operating frequency (MHz) (µs) 4.0 2.0 0.8 0.4 Minimum execution time (instruction cycle) Note: The shaded area is assured only for the MB89855R. Figure 1 Operating Voltage vs. Clock Operating Frequency 23 MB89850R Series 3. DC Characteristics (AVCC = VCC = +5.0 V, AVSS = VSS = 0.0 V, TA = –40°C to +85°C) Parameter Symbol Pin name Value Min. Typ. Max. Unit VIH P00 to P07, P10 to P17, P22, P23 — 0.7 VCC — VCC + 0.3 V VIHS RST, P30 to P37, P40 to P47, P60 to P64 — 0.8 VCC — VCC + 0.3 V VIL P00 to P07, P10 to P17, P22, P23 — VSS – 0.3 — 0.3 VCC V VILS RST, P30 to P37, P40 to P47, P60 to P64 — VSS – 0.3 — 0.2 VCC V “H” level input voltage “L” level input voltage “H” level output voltage VOH P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P47 IOH = –2.0 mA 2.4 — — V VOL P00 to P07, P10 to P17, P20 to P27, P30 to P37, P50 to P57 IOL = +1.8 mA — — 0.4 V VOL2 P40 to P47 IOL = +1.5 mA — — 1.5 V P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P47, P60 to P64, MOD0, MOD1 0.0 V < VI < VCC — — ±5 µA RST VI = 0.0 V 25 50 100 kΩ FC = 10 MHz Normal operation mode (External clock) — 15 18 mA FC = 10 MHz Sleep mode (External clock) — 6 8 mA Stop mode TA = +25°C — — 10 µA “L” level output voltage Input leackage current ILI1 Pull-up resistance RPULL ICC ICCS VCC Power supply current ICCH Input capacitance 24 Condition IA AVCC FC = 10 MHz, when A/D conversion is activated — 6 — µA CIN Other than AVCC, AVSS, VCC, and VSS f = 1 MHz — 10 — pF Remarks With pull-up resistor MB89850R Series 4. AC Characteristics (1) Reset Timing (VCC = +5.0 V±10%, AVSS = VSS = 0.0 V, TA = –40°C to +85°C) Value Parameter Symbol RST “L” pulse width Condition tZLZH Unit — Min. Max. 16 tXCYL* — Remarks ns * : tXCYL is the oscillation cycle (1/FC) to input to the X0 pin. t ZLZH RST 0.2 VCC 0.2 VCC (2) Power-on Reset (AVSS = VSS = 0.0 V, TA = –40°C to +85°C) Value Parameter Power supply rising time Symbol Condition tR Unit Remarks 50 ms Power-on reset function only — ms Due to repeated operations Min. Max. — 1 — Power supply cut-off time tOFF Note: Make sure that power supply rises within the selected oscillation stabilization time. If power supply voltage needs to be varied in the course of operation, a smooth voltage rise is recommended. tOFF tR 2.0 V VCC 0.2 V 0.2 V 0.2 V 25 MB89850R Series (3) Clock Timing (AVSS = VSS = 0.0 V, TA = –40°C to +85°C) Parameter Symbol Clock frequency FC Clock cycle time tXCYL Input clock pulse width PWH PWL Input clock rising/falling time tCR tCF Pin name Value Condition X0, X1 — Unit Remarks Min. Max. 1 10 MHz 100 1000 ns 20 — ns External clock — 10 ns External clock X0 • X0 and X1 Timing Conditions tXCYL PWH PWL tCR 0.8 VCC tCF 0.8 VCC X0 0.2 VCC 0.2 VCC 0.2 VCC • Clock Conditions When a crystal or ceramic resonator is used X0 When an external clock is used X1 X0 X1 Open (4) Instruction Cycle Parameter Instruction cycle (minimum execution time) 26 Symbol tinst Value (typical) Unit Remarks 4/FC µs tinst = 0.4 µs when operating at FC = 10 MHz MB89850R Series (5) Clock Output Timing (VCC = +5.0 V±10%, AVSS = VSS = 0.0 V, TA = –40°C to +85°C) Parameter Cycle time Symbol Pin name tCYC Load condition: 50 pF CLK CLK ↑ → CLK ↓ Condition tCHCL Value Unit Remarks — ns tXCYL × 2 at 10 MHz oscillation 100 ns Approx. tCYC/2 at 10 MHz oscillation Min. Max. 200 30 t CYC t CHCL 2.4 V 2.4 V CLK 0.8 V 27 MB89850R Series (6) Bus Read Timing (VCC = +5.0 V±10%, FC = 10 MHz, AVSS = VSS = 0.0 V, TA = –40°C to +85°C) Parameter Symbol Pin name Condition Value (10 MHz) Min. Max. Unit Remarks Valid address → RD ↓ time tAVRL RD, A15 to A08, AD7 to AD0 1/4 tinst * – 64 ns — ns RD pulse width tRLRH RD 1/2 tinst * – 20 ns — ns Valid address → data read time tAVDV AD7 to AD0, A15 to A08 — 1/2 tinst* ns No wait RD ↓ → data read time tRLDV RD, AD7 to AD0 — 1/2 tinst * – 80 ns ns No wait RD ↑ → data hold time tRHDX AD7 to AD0, RD 0 — ns RD ↑ → ALE ↑ time tRHLH RD, ALE 1/4 tinst * – 40 ns — ns RD ↑ → address invalid time tRHAX RD, A15 to A08 1/4 tinst * – 40 ns — ns RD ↓ → CLK ↑ time tRLCH 1/4 tinst * – 60 ns — ns CLK ↓ → RD ↑ time tCLRH 0 — ns RD ↓ → BUFC ↓ time tRLBL RD, BUFC –5 — ns BUFC ↑ → valid address time tBHAV A15 to A08, AD7 to AD0, BUFC 5 — ns Load condition: 50 pF RD, CLK * : For information on tinst, see “(4) Instruction Cycle.” 2.4 V CLK 0.8 V tRHLH ALE 0.8 V AD 2.4 V 0.7 VCC 0.7 VCC 2.4 V 0.8 V 0.3 VCC 0.3 VCC 0.8 V tRHDX tAVDV A 2.4 V 2.4 V tCLRH 0.8 V tRLCH 0.8 V tAVRL tRLDV 2.4 V 0.8 V tRHAX tRLRH RD 2.4 V 0.8 V tRLBL tBHAV 2.4 V BUFC 0.8 V 28 MB89850R Series (7) Bus Write Timing (VCC = +5.0 V±10%, FC = 10 MHz, AVSS = VSS = 0.0 V, TA = –40°C to +85°C) Parameter Symbol Pin name Condition Value (10 MHz) Unit Remarks Min. Max. 1/4 tinst *1 – 64 ns — ns 5 — ns 1/4 tinst *1 – 60 ns — ns 1 Valid address → ALE ↓ time tAVLL ALE ↓ time → address invalid time tLLAX AD7 to AD0, ALE, A15 to A08 Valid address → WR ↓ time tAVWL WR, ALE WR pulse width tWLWH WR 1/2 tinst * – 20 ns — ns Write data → WR ↑ time tDVWH AD7 to AD0, WR 1/2 tinst *1 – 60 ns — ns 1/4 tinst *1 – 40 ns — ns 1 1/4 tinst * – 40 ns — ns 1 1/4 tinst * – 40 ns — ns 1/4 tinst *1 – 60 ns — ns 0 — ns tXCYL – 35 ns — ns tXCYL – 35 ns*2 — ns WR ↑ → data hold time tWHDX Load WR, A15 to A08 condition: AD7 to AD0, WR 50 pF WR ↑ → ALE ↑ time tWHLH WR, ALE WR ↓ → CLK ↑ time tWLCH CLK ↓ → WR ↑ time tCLWH ALE pulse width tLHLL ALE ALE ↓ → CLK ↑ time tLLCH ALE, CLK WR ↑ → address invalid time tWHAX WR, CLK *2 *1: For information on tinst, see “(4) Instruction Cycle.” *2: These characteristics are also applicable to the bus read timing. 2.4 V CLK 0.8 V tLHLL ALE tLLCH t WHLH 2.4 V 0.8 V tAVLL AD 0.8 V tLLAX 2.4 V 2.4 V 2.4 V 2.4 V 0.8 V 0.8 V 0.8 V 0.8 V tDVWH A 2.4 V 0.8 V tWHDX 2.4 V tCLWH 0.8 V tWLCH tAVWL tWHAX tWLWH WR 2.4 V 0.8 V 29 MB89850R Series (8) Ready Input Timing (VCC = +5.0 V±10%, FC = 10 MHz, AVSS = VSS = 0.0 V, TA = –40°C to +85°C) Value Parameter Symbol RDY valid → CLK ↑ time tYVCH CLK ↑ → RDY invalid time tCHYX Pin name Condition RDY, CLK Load condition: 50 pF Unit Remarks — ns * — ns * Min. Max. 60 0 * : These characteristics are also applicable to the read cycle. 2.4 V CLK 2.4 V ALE AD Address Data A WR t YVCH t CHYX 0.7 VCC 0.7 VCC RDY 0.3 VCC 0.3 VCC t YVCH t CHYX Note: The bus cycle is also extended in the read cycle in the same manner. 30 MB89850R Series (9) UART and Serial I/O Timing (VCC = +5.0 V±10%, AVSS = VSS = 0.0 V, TA = –40°C to +85°C) Parameter Symbol Serial clock cycle time tSCYC SCK1 ↓ → SO1 time SCK2 ↓ → SO2 time tSLOV Valid SI1 → SCK1 ↑ Valid SI2 → SCK2 ↑ tIVSH SCK1 ↑ → valid SI1 hold time SCK2 ↑ → valid SI2 hold time tSHIX Serial clock “H” pulse width tSHSL Serial clock “L” pulse width tSLSH SCK1 ↓ → SO1 time SCK2 ↓ → SO2 time tSLOV Valid SI1 → SCK1 ↑ Valid SI2 → SCK2 ↑ tIVSH SCK1 ↑ → valid SI1 hold time SCK2 ↑ → valid SI2 hold time tSHIX Pin name Condition SCK1,SCK2 SCK1, SO1 Internal shift SCK2, SO2 clock mode SI1, SCK1 Load SI2, SCK2 condition: 50 pF SCK1, SI1 SCK2, SI2 SCK1, SCK2 External shift SCK1, SO1 clock mode SCK2, SO2 Load SI1, SCK1 condition: SI2, SCK2 50 pF SCK1, SI1 SCK2, SI2 Value Unit Min. Max. 2 tinst* — µs –200 200 ns 1/2 tinst* — µs 1/2 tinst* — µs 1 tinst* — µs 1 tinst* — µs 0 200 ns 1/2 tinst* — µs 1/2 tinst* — µs Remarks * : For information on tinst, see “(4) Instruction Cycle.” 31 MB89850R Series • Internal Shift Clock Mode tSCYC SCK1 SCK2 2.4 V 0.8 V 0.8 V tSLOV 2.4 V SO1 SO2 0.8 V tIVSH SI1 SI2 tSHIX 0.8 VCC 0.8 VCC 0.2 VCC 0.2 VCC • External Shift Clock Mode t SLSH t SHSL SCK1 SCK2 0.8 VCC 0.2 VCC 0.8 VCC 0.2 VCC t SLOV SO1 SO2 2.4 V 0.8 V tIVSH SI1 SI2 32 tSHIX 0.8 VCC 0.8 VCC 0.2 VCC 0.2 VCC MB89850R Series (10) Peripheral Input Timing (VCC = +5.0 V±10%, AVSS = VSS = 0.0 V, TA = –40°C to +85°C) Value Parameter Symbol Peripheral input “H” pulse width 1 tILIH1 Peripheral input “L” pulse width 1 tIHIL1 Pin name TRGI, DTTI, ADST, INT0 to INT3 Condition Unit Load condition: 50 pF Min. Max. 2 tinst* — µs 2 tinst* — µs Remarks * : For information on tinst, see “(4) Instruction Cycle.” TRGI DTTI ADST INT0 to INT3 tIHIL1 tILIH1 0.8 VCC 0.2 VCC 0.8 VCC 0.2 VCC 5. A/D Converter Electrical Characteristics (AVCC = VCC = +3.5 V to +6.0 V, FC = 10 MHz, AVSS = VSS = 0.0 V, TA = –40°C to +85°C) Parameter Symbol Pin name Condition Resolution Linearity error — Differential linearity error AVCC = VCC Total error Zero transition voltage VOT Full-scale transition voltage VFST Interchannel disparity — A/D mode conversion time Analog port input current IAIN Analog input voltage — Reference voltage Reference voltage supply current AN0 to AN7 IR AVR Unit Remark s Min. Typ. Max. — — 10 bit — — ±2.0 LSB — — ±1.5 LSB — — ±3.0 LSB AVSS – 1.5 AVSS + 0.5 AVSS + 2.5 LSB AN0 to AN7 — Value AVR – 3.5 AVR – 1.5 AVR + 0.5 LSB — — 4 LSB — — 33 tinst* — µs — — — 10 µA — 0 — AVR V — 0 — AVCC V AVR = 5.0 V — 200 — µA * : For information on tinst, see “(4) Instruction Cycle” in “4. AC Characteristics.” 33 MB89850R Series 6. A/D Converter Glossary • Resolution Analog changes that are identifiable with the A/D converter • Linearity error The deviation of the straight line connecting the zero transition point (“00 0000 0000” ↔ “00 0000 0001”) with the full-scale transition point (“11 1111 1111” ↔´“11 1111 1110”) from actual conversion characteristics • Differential linearity error The deviation of input voltage needed to change the output code by 1 LSB from the theoretical value • Total error The total error indicates the difference between the actual value and theoretical value. This error is caused by the zero transition error, full-scale transition error, linearity error, quantization, and noise. Theoretical I/O value Total error VFST 3FF 3FF 3FE 3FE 1.5 LSB 3FD Digital output Digital output 3FD 004 003 Actual conversion value (1 LSB × N + 0.5 LSB) 004 VNT 003 VOT 002 Actual conversion value 002 1 LSB Theoretical value 001 001 0.5 LSB AVSS AVR Analog input 1 LSB = VFST – VOT 1022 AVSS AVR Analog input (V) Total error of digital output “N” = VNT – (1 LSB × N + 0.5 LSB) 1 LSB (Continued) 34 MB89850R Series (Continued) Zero transition error Full-scale transition error 004 Theoretical value Actual conversion value 3FF Actual conversion value Digital output Digital output 003 002 3FE VFST (Measured value) 3FD Actual conversion value Actual conversion value 001 3FC VOT (Measured value) AVSS AVR Analog input Analog input Linearity error Differential linearity error 3FF Theoretical value Actual conversion value 3FE N+1 (1 LSB × N + VOT) Actual conversion value VNT VFST (Measured value) Digital output Digital output 3FD 004 003 V(N + 1)T N N–1 Actual conversion value VNT Actual conversion value 002 Theoretical value N–2 001 VOT (Measured value) AVSS AVR Analog input Linearity error of digital output “N” = Analog input VNT – (1 LSB × N + VOT) 1 LSB Differential linearity error of digital output “N” = V(N + 1)T – VNT 1 LSB –1 35 MB89850R Series 7. Notes on Using A/D Converter • Input impedance of the analog input pins The A/D converter used for the MB89860/850 series contains a sample hold circuit as illustrated below to fetch analog input voltage into the sample hold capacitor for fifteen instruction cycles after activation A/D conversion. For this reason, if the output impedance of the external circuit for the analog input is high, analog input voltage might not stabilize within the analog input sampling period. Therefore, it is recommended to keep the output impedance of the external circuit low (below 10 kΩ). Note that if the impedance connot be kept low, it is recommended to connect an external capacitor of about 0.1 µF for the analog input pin. • Analog Input Equivalent Circuit Sample hold circuit . C =. 64 pF Anlog input pin Comparator If the analog input impedance is higher than 10 kΩ, it is recommended to connect an external capacitor of approx. 0.1 µF. . R =. 3 kΩ Close for 15 instruction cycles after activating A/D conversion. Analog channel selector • Error The smaller the | AVR – AVSS |, the greater the error would become relatively. 36 MB89850R Series ■ EXAMPLE CHARACTERISTICS (1) “L” Level Output Voltage (P00 to P07, P10 to P17, P20 to P27, P30 to P37, and P50 to P57) (2) “L” Level Output Voltage (P40 to P47) VOL vs. IOL VOL (V) VOL vs. IOL VCC = 3.0 V VCC = 4.0 V TA = +25°C VOL (mV) 600 TA = +25°C 0.5 VCC = 5.0 V 0.4 VCC = 6.0 V 500 VCC = 3.0 V 400 VCC = 4.0 V 0.3 300 0.2 200 0.1 100 0 1 2 3 4 5 6 7 8 9 10 IOL (mA) (3) “H” Level Output Voltage (P00 to P07, P10 to P17, P20 to P27, P30 to P37, and P40 to P47) VCC – VOH (V) 1.0 0.9 VCC = 5.0 V VCC = 6.0 V 0 0 1 2 3 4 5 6 7 8 9 1011121314151617181920 IOL (mA) (4) Pull-up Resistance RPULL vs. VCC RPULL (kΩ) 1000 VCC – VOH vs. IOH TA = +25°C TA = +25°C VCC = 2.5 V 0.8 0.7 0.6 VCC = 3.0 V 0.5 VCC = 4.0 V VCC = 5.0 V VCC = 6.0 V 0.4 0.3 100 0.2 0.1 0.0 0.0 –0.5 –1.0 –1.5 –2.0 –2.5 –3.0 IOH (mA) 10 1 2 3 4 5 6 VCC (V) 37 MB89850R Series (5) “H” Level Input Voltage/“L” Level Input Voltage (CMOS Input) (6) “H” Level Input Voltage/“L” level Input Voltage (Hysteresis Input) VIN vs. VCC VIN (V) 5.0 VIN vs. VCC VIN (V) 5.0 TA = +25°C 4.5 TA = +25°C 4.5 4.0 3.5 4.0 VIHS 3.0 3.5 2.5 3.0 VILS 2.0 2.5 1.5 2.0 1.0 1.5 0.5 1.0 0 0.5 1 2 3 4 5 6 0 1 2 3 4 5 6 7 VCC (V) (7) Operating Supply Current vs. Frequency VIHS: Threshold when input voltage in hysteresis characteristics is set to “H” level VILS: Threshold when input voltage in hysteresis characteristics is set to “L” level (8) Operating Supply Current vs. VCC ICC vs. FC ICC vs. VCC ICC (mA) 25 ICC (mA) 10 TA = +25°C 8 TA = +25°C VCC = 5.0 V 6 20 15 VCC = 3.5 V 4 FC = 10 MHz FC = 8 MHz FC = 6 MHz FC = 4 MHz 10 VCC = 3.0 V 2 5 0 0 2 38 7 VCC (V) 4 6 8 10 FC (MHz) 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VCC (V) MB89850R Series (9) Sleep Power Supply Current vs. Frequency (10) Sleep Power Supply Current vs. VCC ICCS vs. FC ICCS vs. VCC ICCS (mA) 10 ICCS (mA) 10 TA = +25°C TA = +25°C 8 8 6 FC = 10 MHz 6 VCC = 5.0 V 4 FC = 8 MHz FC = 6 MHz 4 FC = 4 MHz VCC = 3.5 V 2 VCC = 3.0 V 0 2 0 2 4 6 8 10 FC (MHz) 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VCC (V) 39 MB89850R Series ■ INSTRUCTIONS (136 INSTRUCTIONS) Execution instructions can be divided into the following four groups: • Transfer • Arithmetic operation • Branch • Others Table 1 lists symbols used for notation of instructions. Table 1 Symbol dir off ext #vct #d8 #d16 dir: b rel @ A AH AL T TH TL IX EP PC SP PS dr CCR RP Ri × (×) (( × )) Instruction Symbols Meaning Direct address (8 bits) Offset (8 bits) Extended address (16 bits) Vector table number (3 bits) Immediate data (8 bits) Immediate data (16 bits) Bit direct address (8:3 bits) Branch relative address (8 bits) Register indirect (Example: @A, @IX, @EP) Accumulator A (Whether its length is 8 or 16 bits is determined by the instruction in use.) Upper 8 bits of accumulator A (8 bits) Lower 8 bits of accumulator A (8 bits) Temporary accumulator T (Whether its length is 8 or 16 bits is determined by the instruction in use.) Upper 8 bits of temporary accumulator T (8 bits) Lower 8 bits of temporary accumulator T (8 bits) Index register IX (16 bits) Extra pointer EP (16 bits) Program counter PC (16 bits) Stack pointer SP (16 bits) Program status PS (16 bits) Accumulator A or index register IX (16 bits) Condition code register CCR (8 bits) Register bank pointer RP (5 bits) General-purpose register Ri (8 bits, i = 0 to 7) Indicates that the very × is the immediate data. (Whether its length is 8 or 16 bits is determined by the instruction in use.) Indicates that the contents of × is the target of accessing. (Whether its length is 8 or 16 bits is determined by the instruction in use.) The address indicated by the contents of × is the target of accessing. (Whether its length is 8 or 16 bits is determined by the instruction in use.) Columns indicate the following: Mnemonic: Assembler notation of an instruction ~: The number of instructions #: The number of bytes Operation: Operation of an instruction TL, TH, AH: A content change when each of the TL, TH, and AH instructions is executed. Symbols in the column indicate the following: • “–” indicates no change. • dH is the 8 upper bits of operation description data. • AL and AH must become the contents of AL and AH prior to the instruction executed. • 00 becomes 00. N, Z, V, C: An instruction of which the corresponding flag will change. If + is written in this column, the relevant instruction will change its corresponding flag. OP code: Code of an instruction. If an instruction is more than one code, it is written according to the following rule: Example: 48 to 4F ← This indicates 48, 49, ... 4F. 40 MB89850R Series Table 2 Mnemonic Transfer Instructions (48 instructions) ~ # Operation TL TH AH NZVC OP code MOV dir,A MOV @IX +off,A MOV ext,A MOV @EP,A MOV Ri,A MOV A,#d8 MOV A,dir MOV A,@IX +off MOV A,ext MOV A,@A MOV A,@EP MOV A,Ri MOV dir,#d8 MOV @IX +off,#d8 MOV @EP,#d8 MOV Ri,#d8 MOVW dir,A MOVW @IX +off,A 3 4 4 3 3 2 3 4 4 3 3 3 4 5 4 4 4 5 2 2 3 1 1 2 2 2 3 1 1 1 3 3 2 2 2 2 – – – – – AL AL AL AL AL AL AL – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – –––– –––– –––– –––– –––– ++–– ++–– ++–– ++–– ++–– ++–– ++–– –––– –––– –––– –––– –––– –––– 45 46 61 47 48 to 4F 04 05 06 60 92 07 08 to 0F 85 86 87 88 to 8F D5 D6 MOVW ext,A MOVW @EP,A MOVW EP,A MOVW A,#d16 MOVW A,dir MOVW A,@IX +off 5 4 2 3 4 5 3 1 1 3 2 2 – – – AL AL AL – – – AH AH AH – – – dH dH dH –––– –––– –––– ++–– ++–– ++–– D4 D7 E3 E4 C5 C6 MOVW A,ext MOVW A,@A MOVW A,@EP MOVW A,EP MOVW EP,#d16 MOVW IX,A MOVW A,IX MOVW SP,A MOVW A,SP MOV @A,T MOVW @A,T MOVW IX,#d16 MOVW A,PS MOVW PS,A MOVW SP,#d16 SWAP SETB dir: b CLRB dir: b XCH A,T XCHW A,T XCHW A,EP XCHW A,IX XCHW A,SP MOVW A,PC 5 4 4 2 3 2 2 2 2 3 4 3 2 2 3 2 4 4 2 3 3 3 3 2 3 1 1 1 3 1 1 1 1 1 1 3 1 1 3 1 2 2 1 1 1 1 1 1 (dir) ← (A) ( (IX) +off ) ← (A) (ext) ← (A) ( (EP) ) ← (A) (Ri) ← (A) (A) ← d8 (A) ← (dir) (A) ← ( (IX) +off) (A) ← (ext) (A) ← ( (A) ) (A) ← ( (EP) ) (A) ← (Ri) (dir) ← d8 ( (IX) +off ) ← d8 ( (EP) ) ← d8 (Ri) ← d8 (dir) ← (AH),(dir + 1) ← (AL) ( (IX) +off) ← (AH), ( (IX) +off + 1) ← (AL) (ext) ← (AH), (ext + 1) ← (AL) ( (EP) ) ← (AH),( (EP) + 1) ← (AL) (EP) ← (A) (A) ← d16 (AH) ← (dir), (AL) ← (dir + 1) (AH) ← ( (IX) +off), (AL) ← ( (IX) +off + 1) (AH) ← (ext), (AL) ← (ext + 1) (AH) ← ( (A) ), (AL) ← ( (A) ) + 1) (AH) ← ( (EP) ), (AL) ← ( (EP) + 1) (A) ← (EP) (EP) ← d16 (IX) ← (A) (A) ← (IX) (SP) ← (A) (A) ← (SP) ( (A) ) ← (T) ( (A) ) ← (TH),( (A) + 1) ← (TL) (IX) ← d16 (A) ← (PS) (PS) ← (A) (SP) ← d16 (AH) ↔ (AL) (dir): b ← 1 (dir): b ← 0 (AL) ↔ (TL) (A) ↔ (T) (A) ↔ (EP) (A) ↔ (IX) (A) ↔ (SP) (A) ← (PC) AL AL AL – – – – – – – – – – – – – – – AL AL – – – – AH AH AH – – – – – – – – – – – – – – – – AH – – – – dH dH dH dH – – dH – dH – – – dH – – AL – – – dH dH dH dH dH ++–– ++–– ++–– –––– –––– –––– –––– –––– –––– –––– –––– –––– –––– ++++ –––– –––– –––– –––– –––– –––– –––– –––– –––– –––– C4 93 C7 F3 E7 E2 F2 E1 F1 82 83 E6 70 71 E5 10 A8 to AF A0 to A7 42 43 F7 F6 F5 F0 Note During byte transfer to A, T ← A is restricted to low bytes. Operands in more than one operand instruction must be stored in the order in which their mnemonics are written. (Reverse arrangement of F2MC-8 family) 41 MB89850R Series Table 3 Mnemonic ~ # ADDC A,Ri ADDC A,#d8 ADDC A,dir ADDC A,@IX +off ADDC A,@EP ADDCW A ADDC A SUBC A,Ri SUBC A,#d8 SUBC A,dir SUBC A,@IX +off SUBC A,@EP SUBCW A SUBC A INC Ri INCW EP INCW IX INCW A DEC Ri DECW EP DECW IX DECW A MULU A DIVU A ANDW A ORW A XORW A CMP A CMPW A RORC A 3 2 3 4 3 3 2 3 2 3 4 3 3 2 4 3 3 3 4 3 3 3 19 21 3 3 3 2 3 2 1 2 2 2 1 1 1 1 2 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 ROLC A 2 1 CMP A,#d8 CMP A,dir CMP A,@EP CMP A,@IX +off CMP A,Ri DAA DAS XOR A XOR A,#d8 XOR A,dir XOR A,@EP XOR A,@IX +off XOR A,Ri AND A AND A,#d8 AND A,dir 2 3 3 4 3 2 2 2 2 3 3 4 3 2 2 3 2 2 1 2 1 1 1 1 2 2 1 2 1 1 2 2 Arithmetic Operation Instructions (62 instructions) Operation TL TH AH NZVC OP code – – – – – – – – – – – – – – – – – – – – – – – dL – – – – – – – – – – – – – – – – – – – – – – – – – – – – – 00 – – – – – – – – – – – dH – – – – – – dH – – – – dH – – – dH dH 00 dH dH dH – – – ++++ ++++ ++++ ++++ ++++ ++++ ++++ ++++ ++++ ++++ ++++ ++++ ++++ ++++ +++– –––– –––– ++–– +++– –––– –––– ++–– –––– –––– ++R– ++R– ++R– ++++ ++++ ++–+ 28 to 2F 24 25 26 27 23 22 38 to 3F 34 35 36 37 33 32 C8 to CF C3 C2 C0 D8 to DF D3 D2 D0 01 11 63 73 53 12 13 03 C ← A← – – – ++–+ 02 (A) − d8 (A) − (dir) (A) − ( (EP) ) (A) − ( (IX) +off) (A) − (Ri) Decimal adjust for addition Decimal adjust for subtraction (A) ← (AL) ∀ (TL) (A) ← (AL) ∀ d8 (A) ← (AL) ∀ (dir) (A) ← (AL) ∀ ( (EP) ) (A) ← (AL) ∀ ( (IX) +off) (A) ← (AL) ∀ (Ri) (A) ← (AL) ∧ (TL) (A) ← (AL) ∧ d8 (A) ← (AL) ∧ (dir) – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – ++++ ++++ ++++ ++++ ++++ ++++ ++++ ++R– ++R– ++R– ++R– ++R– ++R– ++R– ++R– ++R– 14 15 17 16 18 to 1F 84 94 52 54 55 57 56 58 to 5F 62 64 65 (A) ← (A) + (Ri) + C (A) ← (A) + d8 + C (A) ← (A) + (dir) + C (A) ← (A) + ( (IX) +off) + C (A) ← (A) + ( (EP) ) + C (A) ← (A) + (T) + C (AL) ← (AL) + (TL) + C (A) ← (A) − (Ri) − C (A) ← (A) − d8 − C (A) ← (A) − (dir) − C (A) ← (A) − ( (IX) +off) − C (A) ← (A) − ( (EP) ) − C (A) ← (T) − (A) − C (AL) ← (TL) − (AL) − C (Ri) ← (Ri) + 1 (EP) ← (EP) + 1 (IX) ← (IX) + 1 (A) ← (A) + 1 (Ri) ← (Ri) − 1 (EP) ← (EP) − 1 (IX) ← (IX) − 1 (A) ← (A) − 1 (A) ← (AL) × (TL) (A) ← (T) / (AL),MOD → (T) (A) ← (A) ∧ (T) (A) ← (A) ∨ (T) (A) ← (A) ∀ (T) (TL) − (AL) (T) − (A) → C→A (Continued) 42 MB89850R Series (Continued) Mnemonic AND A,@EP AND A,@IX +off AND A,Ri OR A OR A,#d8 OR A,dir OR A,@EP OR A,@IX +off OR A,Ri CMP dir,#d8 CMP @EP,#d8 CMP @IX +off,#d8 CMP Ri,#d8 INCW SP DECW SP ~ # Operation 3 4 3 2 2 3 3 4 3 5 4 5 4 3 3 1 2 1 1 2 2 1 2 1 3 2 3 2 1 1 (A) ← (AL) ∧ ( (EP) ) (A) ← (AL) ∧ ( (IX) +off) (A) ← (AL) ∧ (Ri) (A) ← (AL) ∨ (TL) (A) ← (AL) ∨ d8 (A) ← (AL) ∨ (dir) (A) ← (AL) ∨ ( (EP) ) (A) ← (AL) ∨ ( (IX) +off) (A) ← (AL) ∨ (Ri) (dir) – d8 ( (EP) ) – d8 ( (IX) + off) – d8 (Ri) – d8 (SP) ← (SP) + 1 (SP) ← (SP) – 1 Table 4 Mnemonic BZ/BEQ rel BNZ/BNE rel BC/BLO rel BNC/BHS rel BN rel BP rel BLT rel BGE rel BBC dir: b,rel BBS dir: b,rel JMP @A JMP ext CALLV #vct CALL ext XCHW A,PC RET RETI ~ # 3 3 3 3 3 3 3 3 5 5 2 3 6 6 3 4 6 2 2 2 2 2 2 2 2 3 3 1 3 1 3 1 1 1 Mnemonic PUSHW A POPW A PUSHW IX POPW IX NOP CLRC SETC CLRI SETI ~ # 4 4 4 4 1 1 1 1 1 1 1 1 1 1 1 1 1 1 TH AH NZVC OP code – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – ++R– ++R– ++R– ++R– ++R– ++R– ++R– ++R– ++R– ++++ ++++ ++++ ++++ –––– –––– 67 66 68 to 6F 72 74 75 77 76 78 to 7F 95 97 96 98 to 9F C1 D1 Branch Instructions (17 instructions) Operation If Z = 1 then PC ← PC + rel If Z = 0 then PC ← PC + rel If C = 1 then PC ← PC + rel If C = 0 then PC ← PC + rel If N = 1 then PC ← PC + rel If N = 0 then PC ← PC + rel If V ∀ N = 1 then PC ← PC + rel If V ∀ N = 0 then PC ← PC + reI If (dir: b) = 0 then PC ← PC + rel If (dir: b) = 1 then PC ← PC + rel (PC) ← (A) (PC) ← ext Vector call Subroutine call (PC) ← (A),(A) ← (PC) + 1 Return from subrountine Return form interrupt Table 5 TL TL TH AH NZVC OP code – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – dH – – –––– –––– –––– –––– –––– –––– –––– –––– –+–– –+–– –––– –––– –––– –––– –––– –––– Restore FD FC F9 F8 FB FA FF FE B0 to B7 B8 to BF E0 21 E8 to EF 31 F4 20 30 Other Instructions (9 instructions) Operation TL TH AH NZVC OP code – – – – – – – – – – – – – – – – – – – dH – – – – – – – –––– –––– –––– –––– –––– –––R –––S –––– –––– 40 50 41 51 00 81 91 80 90 43 L 44 MOV CMP ADDC SUBC MOV XOR AND OR MOV CMP SETB BBS INC A,R0 A,R0 A,R0 A,R0 R0,A A,R0 A,R0 A,R0 R0,#d8 R0,#d8 dir: 0 dir: 0,rel MOV CMP ADDC SUBC MOV XOR AND OR MOV CMP SETB BBS INC A,R1 A,R1 A,R1 A,R1 R1,A A,R1 A,R1 A,R1 R1,#d8 R1,#d8 dir: 1 dir: 1,rel MOV CMP ADDC SUBC MOV XOR AND OR MOV CMP SETB BBS INC A,R2 A,R2 A,R2 A,R2 R2,A A,R2 A,R2 A,R2 R2,#d8 R2,#d8 dir: 2 dir: 2,rel MOV CMP ADDC SUBC MOV XOR AND OR MOV CMP SETB BBS INC A,R3 A,R3 A,R3 A,R3 R3,A A,R3 A,R3 A,R3 R3,#d8 R3,#d8 dir: 3 dir: 3,rel MOV CMP ADDC SUBC MOV XOR AND OR MOV CMP SETB BBS INC A,R4 A,R4 A,R4 A,R4 R4,A A,R4 A,R4 A,R4 R4,#d8 R4,#d8 dir: 4 dir: 4,rel MOV CMP ADDC SUBC MOV XOR AND OR MOV CMP SETB BBS INC A,R5 A,R5 A,R5 A,R5 R5,A A,R5 A,R5 A,R5 R5,#d8 R5,#d8 dir: 5 dir: 5,rel MOV CMP ADDC SUBC MOV XOR AND OR MOV CMP SETB BBS INC A,R6 A,R6 A,R6 A,R6 R6,A A,R6 A,R6 A,R6 R6,#d8 R6,#d8 dir: 6 dir: 6,rel MOV CMP ADDC SUBC MOV XOR AND OR MOV CMP SETB BBS INC A,R7 A,R7 A,R7 A,R7 R7,A A,R7 A,R7 A,R7 R7,#d8 R7,#d8 dir: 7 dir: 7,rel 9 A B C D E F A SUBC A XCH A, T XOR A AND A OR A MOV MOV CLRB BBC INCW DECW MOVW MOVW @A,T A,@A dir: 2 dir: 2,rel IX IX IX,A A,IX XOR AND OR DAA A,#d8 A,#d8 A,#d8 DAS R7 R6 R5 R4 R3 R2 R1 R0 DEC DEC DEC DEC DEC DEC DEC DEC R7 R6 R5 R4 R3 R2 R1 R0 rel rel rel rel CALLV BLT #7 rel CALLV BGE #6 rel CALLV BZ #5 CALLV BNZ #4 rel CALLV BN #3 CALLV BP #2 CALLV BC #1 CALLV BNC #0 rel CLRB BBC MOVW MOVW MOVW XCHW dir: 4 dir: 4,rel A,ext ext,A A,#d16 A,PC ADDCW SUBCW XCHW XORW ANDW ORW MOVW MOVW CLRB BBC INCW DECW MOVW MOVW A A A, T A A A @A,T A,@A dir: 3 dir: 3,rel EP EP EP,A A,EP ADDC CLRB BBC INCW DECW MOVW MOVW dir: 1 dir: 1,rel SP SP SP,A A,SP 8 A A SETC MOV CMP ADDC SUBC MOV XOR AND OR MOV CMP CLRB BBC MOVW MOVW MOVW XCHW A,@EP A,@EP A,@EP A,@EP @EP,A A,@EP A,@EP A,@EP @EP,#d8 @EP,#d8 dir: 7 dir: 7,rel A,@EP @EP,A EP,#d16 A,EP CMPW CMP JMP CALL PUSHW POPW MOV MOVW CLRC addr16 addr16 IX IX ext,A PS,A 7 F MOV CMP ADDC SUBC MOV XOR AND OR MOV CMP CLRB BBC MOVW MOVW MOVW XCHW A,@IX +d A,@IX +d A,@IX +d A,@IX +d @IX +d,A A,@IX +d A,@IX +d A,@IX +d @IX +d,#d8 @IX +d,#d8 dir: 6 dir: 6,rel A,@IX +d @IX +d,A IX,#d16 A,IX E 6 D MOV CMP ADDC SUBC MOV XOR AND OR MOV CMP CLRB BBC MOVW MOVW MOVW XCHW A,dir A,dir A,dir A,dir dir,A A,dir A,dir A,dir dir,#d8 dir,#d8 dir: 5 dir: 5,rel A,dir dir,A SP,#d16 A,SP C 5 B CLRB BBC INCW DECW JMP MOVW dir: 0 dir: 0,rel A A @A A,PC A MOV CMP ADDC SUBC A,#d8 A,#d8 A,#d8 A,#d8 A A DIVU SETI 9 4 8 RORC 7 3 6 ROLC A 5 PUSHW POPW MOV MOVW CLRI A A A,ext A,PS 4 2 A RETI 3 MULU RET 2 1 SWAP 1 NOP 0 0 H MB89850R Series ■ INSTRUCTION MAP MB89850R Series ■ MASK OPTIONS (MB89855R) Option type Option selection Power-on reset 0: Without power-on reset 1: With power-on reset Initial value of oscillation stabilization delay time 0: 218/FC (s) (Crystal oscillator) 1: 214/FC (s) (Ceramic oscillator) Reset pin output 0: Without reset output 1: With reset output Pull-up resistor at port pin P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P47, P60 to P64 1: Without pull-up resistor 0: With pull-up resistor Remarks — Selects the initial value of the OSCS bit in the STBC register during power-on reset. — • Can be set per pin. • P00 to P07, P10 to P17, and P20 to P27 with a pull-up resistor can be set only for single-chip mode. ■ STANDARD OPTION LIST Part number Parameter MB89P857/W857 Power-on reset Available Initial value of oscillation stabilization delay time 218/FC (s) Output at reset pin Available Pull-up resistor at port pin Not available ■ ORDERING INFORMATION Part number Package Remarks MB89855RP-SH MB89P857P-SH 64-pin Plastic SH-DIP (DIP-64P-M01) MB89W857C-SH 64-pin Ceramic SH-DIP (DIP-64C-A06) ES level only 64-pin Ceramic QFP (FPT-64C-A02) ES level only MB89W857CF-ES-BND 45 MB89850R Series ■ PACKAGE DIMENSIONS 64-pin Plastic SH-DIP (DIP-64P-M01) +0.22 58.00 –0.55 +.008 2.283 –.022 INDEX-1 17.00±0.25 (.669±.010) INDEX-2 5.65(.222)MAX 0.25±0.05 (.010±.002) 3.00(.118)MIN +0.50 1.00 –0 +.020 .039 –0 0.45±0.10 (.018±.004) 0.51(.020)MIN 15°MAX 19.05(.750) TYP 1.778±0.18 (.070±.007) 55.118(2.170)REF 1.778(.070) MAX C Dimensions in mm (inches) 1994 FUJITSU LIMITED D64001S-3C-4 64-pin Ceramic SH-DIP (DIP-64C-A06) 56.90±0.56 (2.240±.022) 8.89(.350) DIA TYP R1.27(.050) REF 18.75±0.25 (.738±.010) INDEX AREA 1.27±0.25 (.050±.010) 5.84(.230)MAX 0.25±0.05 (.010±.004) 3.40±0.36 (.134±.014) 1.45(.057) MAX C 46 1994 FUJITSU LIMITED D64006SC-1-2 1.778±0.180 (.070±.007) 0.90±0.10 (.0355±.0040) +0.13 0.46 –0.08 +.005 .018 –.003 19.05±0.25 (.750±.010) 0°~9° 55.118(2.170)REF Dimensions in mm (inches) MB89850R Series 64-pin Plastic QFP (FPT-64P-M06) 24.70±0.40(.972±.016) 3.35(.132)MAX 20.00±0.20(.787±.008) 51 0.05(.002)MIN (STAND OFF) 33 52 32 14.00±0.20 (.551±.008) 18.70±0.40 (.736±.016) 12.00(.472) REF 16.30±0.40 (.642±.016) INDEX 20 64 "A" LEAD No. 19 1 1.00(.0394) TYP 0.40±0.10 (.016±.004) 0.15±0.05(.006±.002) 0.20(.008) M Details of "A" part 0.25(.010) Details of "B" part "B" 0.30(.012) 0.10(.004) 0.63(.025)MAX 22.30±0.40(.878±.016) C 0 10° 1.20±0.20 (.047±.008) 0.18(.007)MAX 18.00(.709)REF Dimensions in mm (inches) 1994 FUJITSU LIMITED F64013S-3C-2 64-pin Ceramic QFP (FPT-64C-A02) 0.51(.020) TYP 9.40(.370)TYP 17.91(.705) TYP 16.00(.630) 14.00±0.25 TYP (.551±.010) 12.01(.473) REF 16.31(.642) TYP INDEX AREA 1.00±0.10 0.40±0.08 (.0394±.0040) (.016±.003) 18.00(.709) REF 0.15±0.05 (.006±.002) 1.60(.063) TYP 1.00±0.10 (.0394±.0040) 4.70(.185)MAX 20.00±0.25 (.787±.010) 23.90(.941) TYP 22.00(.866) TYP 22.30(.878) TYP C 1994 FUJITSU LIMITED F64012SC-2-2 0.80(.0315) TYP Dimensions in mm (inches) 47 MB89850R Series FUJITSU LIMITED For further information please contact: Japan FUJITSU LIMITED Corporate Global Business Support Division Electronic Devices KAWASAKI PLANT, 4-1-1, Kamikodanaka, Nakahara-ku, Kawasaki-shi, Kanagawa 211-8588, Japan Tel: +81-44-754-3763 Fax: +81-44-754-3329 http://www.fujitsu.co.jp/ North and South America FUJITSU MICROELECTRONICS, INC. 3545 North First Street, San Jose, CA 95134-1804, USA Tel: +1-408-922-9000 Fax: +1-408-922-9179 Customer Response Center Mon. - Fri.: 7 am - 5 pm (PST) Tel: +1-800-866-8608 Fax: +1-408-922-9179 http://www.fujitsumicro.com/ Europe FUJITSU MICROELECTRONICS EUROPE GmbH Am Siebenstein 6-10, D-63303 Dreieich-Buchschlag, Germany Tel: +49-6103-690-0 Fax: +49-6103-690-122 http://www.fujitsu-fme.com/ Asia Pacific FUJITSU MICROELECTRONICS ASIA PTE LTD #05-08, 151 Lorong Chuan, New Tech Park, Singapore 556741 Tel: +65-281-0770 Fax: +65-281-0220 http://www.fmap.com.sg/ F9609 FUJITSU LIMITED Printed in Japan All Rights Reserved. The contents of this document are subject to change without notice. Customers are advised to consult with FUJITSU sales representatives before ordering. The information and circuit diagrams in this document are presented as examples of semiconductor device applications, and are not intended to be incorporated in devices for actual use. Also, FUJITSU is unable to assume responsibility for infringement of any patent rights or other rights of third parties arising from the use of this information or circuit diagrams. The contents of this document may not be reproduced or copied without the permission of FUJITSU LIMITED. FUJITSU semiconductor devices are intended for use in standard applications (computers, office automation and other office equipments, industrial, communications, and measurement equipments, personal or household devices, etc.). CAUTION: Customers considering the use of our products in special applications where failure or abnormal operation may directly affect human lives or cause physical injury or property damage, or where extremely high levels of reliability are demanded (such as aerospace systems, atomic energy controls, sea floor repeaters, vehicle operating controls, medical devices for life support, etc.) are requested to consult with FUJITSU sales representatives before such use. The company will not be responsible for damages arising from such use without prior approval. Any semiconductor devices have inherently a certain rate of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. If any products described in this document represent goods or technologies subject to certain restrictions on export under the Foreign Exchange and Foreign Trade Control Law of Japan, the prior authorization by Japanese government should be required for export of those products from Japan.