MICRF104 Micrel MICRF104 1.8V, QwikRadio™ UHF ASK Transmitter Final Information General Description Features The MICRF104 is a low voltage Transmitter IC for remote wireless applications. The device employs Micrel’s latest QwikRadio™ technology. This device is a true “data-in, antenna-out” device. All antenna tuning is accomplished automatically within the IC which eliminates manual tuning, and reduces production costs. The result is a highly reliable yet extremely low cost solution for high volume wireless applications. The MICRF104 incorporates a DC/DC converter to boost the input voltage up to 5V for the RF portion of the IC. This feature enables the MICRF104 to operate off supply voltages as low as 1.8V and transmit at power in excess of –2dBm. The MICRF104 uses a novel architecture where the external loop antenna is tuned to the internal UHF synthesizer. This transmitter is designed to comply worldwide UHF unlicensed band intentional radiator regulations. The IC is compatible with virtually all ASK/OOK (Amplitude Shift Keying/On-Off Keyed) UHF receiver types from wide-band super-regenerative radios to narrow-band, high performance super-heterodyne receivers. The transmitter is designed to work with transmitter data rates from 100 to 20k bits per second. The automatic tuning in conjunction with the external resistor, insures that the transmitter output power stays constant for the life of the battery. When coupled with Micrel’s family of QwikRadio™ receivers, the MICRF104 provides the lowest cost and most reliable remote actuator and RF link system available. • • • • • Complete UHF transmitter on a chip Frequency range 300MHz to 470MHz Data rates to 20kbps Automatic antenna alignment, no manual adjustment Low external part count Applications • • • • Remote Keyless Entry Systems (RKE) Remote Fan/Light Control Garage Door Opener Transmitters Remote Sensor Data Links Ordering Information Part Number Temperature Range Package MICRF104BM 0°C to +85°C 14-Pin SOIC Typical Application L1 22µH MICRF104 1.8V to 4V Supply 1 VDDPWR 2 VSS 10µF 3 EN 14 VSS 13 5V SW 4 VSS PC 5 REFOSC VDDRF RF Standby 12 0.1µF 11 100pF 10µF Power Control 10 9 6 RFSTBY 7 ANTM ASK ANTP DATA IN 8 LOOP ANTENNA (PCB TRACE) Figure 1 QwikRadio is a trademark of Micrel, Inc. The QwikRadio ICs were developed under a partnership agreement with AIT of orlando, Florida Micrel, Inc. • 1849 Fortune Drive • San Jose, CA 95131 • USA • tel + 1 (408) 944-0800 • fax + 1 (408) 944-0970 • http://www.micrel.com November 8, 2001 1 MICRF104 MICRF104 Micrel Pin Configuration VDDPWR 1 14 EN VSS 2 13 VSS 5V 3 12 SW VSS 4 11 PC REFOSC 5 10 VDDRF RFSTBY 6 9 ASK ANTM 7 8 ANTP MICRF104BM Pin Description Pin Number Pin Name Pin Function 1 VDDPWR Positive power supply input for the DC/DC converter. 2, 4, 13 VSS 3 5V 5 REFOSC This is the timing reference frequency which is the transmit frequency divided by 32. Connect a crystal (mode dependent) between this pin and VSS, or drive the input with an AC coupled 0.5Vpp input clock. See Reference Oscillator Section in this data sheet 6 RFSTBY Input for transmitter standby control pin is pulled to VDDRF for transmit operation and VSS for stand-by mode. 7 ANTM Negative RF power output to drive the low side of the transmit loop antenna 8 ANTP Positive RF power output to drive the high side of the transmit loop antenna 9 ASK 10 VDDRF Positive power supply input for the RF circuit. A power supply bypass capacitor connected from VDDRF to VSS should have the shortest possible path. 11 PC Power Control Input. The voltage at this pin should be set between 0.3V to 0.4V for normal operation. 12 SW DC/DC converter Switch. NPN output switch transistor collector. 14 EN Chip Enable input. Active high MICRF104 Ground return 5V Output from the DC / DC converter Amplitude Shift Key modulation data input pin. 2 November 8, 2001 MICRF104 Micrel Absolute Maximum Ratings (Note 1) Operating Ratings (Note 2) Supply Voltage(VDDPWR, VDDRF) .................................. +6V Voltage on I/O Pin EN .................................................. [tbd] Voltage on I/O Pins, RFSTBY, ASK, PC, ANTP, ANTM VSS–0.3 to VDD+0.3 Storage Temperature Range ................... -65°C to + 150°C Lead Temperature (soldering, 10 seconds) ........... + 300°C ESD Rating .............................................................. Note 3 Supply Voltage (VDDPWR) .................................. 1.8V to 4V PC Input Range .................................. 0.15V < VPC < 0.35V Ambient Operating Temperature (TA) ............ 0°C to +85°C Programmable Transmitter Frequency Range: 300MHz to 470MHz Electrical Characteristics Specifications apply for VDDPWR = 1.8V, VPC = 0.35V, freqREFOSC = 12.1875MHz, RFSTBY = VDDRF, EN = VDDPWR. TA = 25°C, bold values indicate 0°C ≤ TA ≤ 85°C unless otherwise noted. Parameter Condition Min Typ Max Units Power Supply Shutdown current, IVDDPWR EN = RFSTBY = VSS 50 µA RF Standby supply, IVDDPWR RFSTBY = VSS, EN = VDDPWR 1.5 mA RF Standby supply, IVDDPWR RFSTBY = VSS, EN = VDDPWR = 4V 0.6 mA MARK supply current, ION Note 4, 31 41 mA Note 4, VDDPWR = 4V 12 17 mA 22 30 mA VDDPWR = 4V 9 12 mA 33% mark/space ratio, Note 4 25 34 mA 33% mark/space ratio, VDDRWR = 4V, Note 4 10 14 mA SPACE supply current, IOFF Mean operating current 5V Max. output current Note 9, VDDPWR = 4V 5V Output Voltage range Note 9 15 mA 35 mA 4.75 5.25 V RF Output Section and Modulation Limits: Output power level, POUT Transmitted Power Harmonics output @315MHz; Note 4, Note 5 –2 dBm @433MHz; Note 4, Note 5 –2.5 dBm @315MHz tbd µV/m @433MHz tbd µV/m @ 315MHz 2nd harm. 3rd harm. –46 –45 dBc @433 MHz 2nd harm. 3rd harm. –50 –41 dBc 40 52 dBc 5 6.5 Extinction ratio for ASK Varactor tuning range Note 7 8 pF Reference Oscillator Section Reference Oscillator Input Impedance Reference Oscillator Source Current Reference Oscillator Input Voltage (peak to peak) November 8, 2001 0.2 3 300 kΩ 6 µA 0.5 VPP MICRF104 MICRF104 Parameter Micrel Condition Min Typ Max Units Digital / Control Section Calibration time Note 8, ASK=HIGH 25 ms Power amplifier output hold off time from STBY Note 9, STDBY transition from LOW to HIGH Crystal, ESR < 20Ω 6 ms Transmitter Stabilization Time From External Reference (500mVpp) 10 ms From STBY Crystal, ESR < 20Ω 19 ms Maximum Data rate - ASK modulation Duty cycle of the modulating signal = 50% VRFSTBY Enable Voltage kbits/s 0.75VDDRF 0.6VDDRF 5 STBY Sink Current VEN Enable Voltage 20 High EN pin current 0.3 V 10 µA 0.8VDDRF V VIL, input low voltage ASK = 0V, 5.0V input current –10 µA V –10 VIH, input high voltage ASK input current 6.5 0.95VDDPWR Low ASK pin V 0.1 0.2VDDRF V 10 µA Note 1. Exceeding the absolute maximum rating may damage the device. Note 2. The device is not guaranteed to function outside its operating rating. Note 3. Devices are ESD sensitive. Handling precautions recommended. Human body model, 1.5k in series with 100pF. Note 4. Supply current and output power are a function of the voltage input on the PC (power control) pin. All specifications in the Electrical Characteristics table applies for condition VPC = 350mV. Increasing the voltage on the PC pin will increase transmit power and also increase MARK supply current. Refer to the graphs "Output Power Versus PC Pin Voltage" and "Mark Current Versus PC Pin Voltage." Note 5. Output power specified into a 50Ω equivalent load using the test circuit in Figure 5. Note 6. Transmitted power measured 3 meters from the antenna using transmitter board TX102-2A in Figure 6. Note 7. The Varactor capacitance tuning range indicates the allowable external antenna component variation to maintain tune over normal production tolerances of external components. Guaranteed by design not tested in production. Note 8. When the device is first powered up or it loses power momentarily, it goes into the calibration mode to tune up the transmit antenna. Note 9. After the release of the STDBY, the device requires an initialization time to settle the REFOSC and the internal PLL. The first MARK state (ASK HIGH) after exit from STDBY needs to be longer than the initialization time. The subsequent low to high transitions will be treated as data modulation whereby the envelope transition time will apply. Note 10. The MICRF102 was tested to be Compliant to Part 15.231 for maximum allowable TX power, when operated in accordance with a loop antenna described in Figure 6. MICRF104 4 November 8, 2001 MICRF104 Micrel Typical Characteristics Output Power vs PC Pin Voltage Mark Current vs PC Pin Voltage 25 0 -10 -15 -20 -25 15 10 5 -30 -35 0 November 8, 2001 20 -5 CURRENT (mA) OUTPUT POWER (dBm) 5 0 0 100 200 300 400 500 600 VPC (mV) 5 100 200 300 400 500 600 VPC (mV) MICRF104 MICRF104 Micrel Functional Diagram VDDPWR Oscillator SW Thermal Shutdown EN Enable Logic Driver 5V Error Amplifier 1.2V Bandgap Reference VSS DC/DC Converter Reference Bias STBY VDD ASK (10) TX Bias Control VDDRF ANTP Power Amp ANTM (8) (9) Prescaler Divide by 32 PC Buffer (6a) (5) Phase Detector Buffer VCO (4) (2) (6b) Antenna Tuning Control (3) (7) Varactor Device REF.OSC Reference Oscillator (1) (11) VSS RF Transmitter Figure 2. MICRF104 Block Diagram (RF Circuit) The Antenna tuner block senses the phase of the transmit signal at the antenna port and controls the varactor capacitor to tune the antenna. The Power control unit senses the antenna signal and controls the PA bias current to regulate the antenna signal to the transmit power. The Process tune circuit generates process independent bias currents for different blocks. A PCB antenna loop coupled with a resonator and a resistor divider network are all the components required to construct Functional Description The block diagram illustrates the basic structure of the RF portion of the MICRF104. Identified in the figure are the principal functional blocks of the IC, namely the (1, 2, 3, 4, 5) UHF Synthesizer, (6a/b) Buffer, (7) Antenna tuner, (8) Power amplifier, (9) TX bias control, (10) Reference bias and (11) Process tuner. The UHF synthesizer generates the carrier frequency with quadrature outputs. The in-phase signal (I) is used to drive the PA and the quadrature signal (Q) is used to compare the antenna signal phase for antenna tuning purpose. MICRF104 6 November 8, 2001 MICRF104 Micrel a complete UHF transmitter for remote actuation applications such as automotive keyless entry. Included within the IC is a differential varactor that serves as the tuning element to insure that the transmit frequency and antenna are aligned with the receiver over all supply and temperature variations. November 8, 2001 7 MICRF104 MICRF104 Micrel The tolerance in the antenna inductance combined with the tolerance of the capacitor in parallel with it will result in significant differences in resonant frequency from one transmitter to another. Many conventional loop antenna transmitters use a variable capacitor for manual tuning of the resonant circuit in production. Manual tuning increases cost and reduces reliability. A capacitor correctly tuned during manufacture may drift over time and temperature. A change in capacitance will alter the resonant frequency and reduce radiated power. In addition, a hand close to the antenna will alter the resonant properties of the antenna and de-tune it. The MICRF104 features automatic tuning. The MICRF104 automatically tunes itself to the antenna, eradicating the need for manual tuning in production. It also dynamically adapts to changes in impedance in operation and compensates for the hand-effect. Automatic Antenna Tuning The output stage of the MICRF104 consists of a variable capacitor (varactor) with a nominal value of 6.5pF tunable over a range from 5pF to 8pF. The MICRF104 monitors the phase of the signal on the output of the power amplifier and automatically tunes the resonant circuit by setting the varactor value at the correct capacitance to achieve resonance. In the simplest implementation, the inductance of the loop antenna should be chosen such that the nominal value is resonant at 6.5pF, the nominal mid-range value of the MICRF104 output stage varactor. Using the equation: Applications Information Design Process The MICRF104 transmitter design process is as follows: 1). Set the transmit frequency by providing the correct reference oscillator frequency 2). Ensure antenna resonance at the transmit frequency by: a. Either, matching antenna inductance to the center of the tuning range of the internal varactor. b. Or, matching capacitance with the antenna inductance by adding an external capacitor (in series with, or in parallel with, the internal varactor) 3). Set PC pin for desired transmit power. Reference Oscillator Selection An external reference oscillator is required to set the transmit frequency. The transmit frequency will be 32 times the reference oscillator frequency. fTX = 32 × fREFOSC Crystals or a signal generator can be used. Correct reference oscillator selection is critical to ensure operation. Crystals must be selected with an ESR of 20 Ohms or less. If a signal generator is used, the input amplitude must be greater than 200 mVP-P and less than 500 mVP-P. Antenna Considerations The MICRF104 is designed specifically to drive a loop antenna. It has a differential output designed to drive an inductive load. The output stage of the MICRF104 includes a varactor that is automatically tuned to the inductance of the antenna to ensure resonance at the transmit frequency. A high-Q loop antenna should be accurately designed to set the center frequency of the resonant circuit at the desired transmit frequency. Any deviation from the desired frequency will reduce the transmitted power. The loop itself is an inductive element. The inductance of a typical PCB-trace antenna is determined by the size of the loop, the width of the antenna traces, PCB thickness and location of the ground plane. The tolerance of the inductance is set by the manufacturing tolerances and will vary depending how the PCB is manufactured. In the simplest implementation a single capacitor in parallel with the antenna will provide the desired resonant circuit. C L= If the inductance of the antenna cannot be set at the nominal value determined by the above equation, a capacitor can be added in parallel or series with the antenna. In this case, the varactor internal to the MICRF104 acts to trim the total capacitance value. CVARACTOR LANTENNA Starting with the inductance of the antenna the capacitance value required to achieve resonance can be calculated. For example a 315MHz transmitter with a 45.1nH inductance antenna will require no capacitor in parallel with the antenna, only the internal varactor that will be tuned to 5.66pF, which is very close to mid range and can be determined using the equation: LANTENNA C= The resonant frequency is determined by the equation: 1 4 π 2 f 2L Where: f = 315Mhz 1 4 CL MICRF104 CEXTERNAL Figure 4. Figure 3. f= 1 4 π 2 f 2C π2 8 November 8, 2001 MICRF104 Micrel L = 45.1nH The value of the capacitor is calculated as 5.66pF. Supply Bypassing Correct supply bypassing is essential. A 4.7uF capacitor in parallel with a 100pF capacitor is required and an additional 0.1µF capacitor in parallel is recommended. The MICRF104 is susceptible to supply-line ripple, if supply regulation is poor or bypassing is inadequate, spurs will be evident in the transmit spectrum. Transmit Power The transmit power specified in this datasheet is normalized to a 50Ohm load. The antenna efficiency will determine the actual radiated power. Good antenna design will yield transmit power in the range of 67dBµV/m to 80dBµV/m at 3 meters. The PC pin on the MICRF104 is used to set the transmit power. The differential voltage on the output of the PA (power amplifier) is proportional to the voltage at the PC pin. November 8, 2001 If the PC pin voltage rises above 0.4 V the output power becomes current limited. At this point, further increase in the PC pin voltage will not increase the RF output power in the antenna pins. Low power consumption is achieved by decreasing the voltage in the PC pin, also reducing the RF output power and maximum range. Output Blanking When the device is first powered up or after a momentary loss of power the output is automatically blanked (disabled). This feature ensures RF transmission only occurs under controlled conditions when the synthesizer is fully operational, preventing unintentional transmission at an undesired frequency. Output blanking is key to guaranteeing compliance with UHF regulations by ensuring transmission only occurs in the intended frequency band. 9 MICRF104 MICRF104 Micrel Package Information PIN 1 DIMENSIONS: INCHES (MM) 0.154 (3.90) 0.026 (0.65) MAX) 0.193 (4.90) 0.050 (1.27) 0.016 (0.40) TYP TYP 45° 0.006 (0.15) 0.057 (1.45) 0.049 (1.25) 0.344 (8.75) 0.337 (8.55) 3°–6° 0.244 (6.20) 0.228 (5.80) SEATING PLANE 14-Pin SOIC (M) MICREL INC. 1849 FORTUNE DRIVE SAN JOSE, CA 95131 TEL + 1 (408) 944-0800 FAX + 1 (408) 944-0970 WEB USA http://www.micrel.com This information is believed to be accurate and reliable, however no responsibility is assumed by Micrel for its use nor for any infringement of patents or other rights of third parties resulting from its use. No license is granted by implication or otherwise under any patent or patent right of Micrel Inc. © 2001 Micrel Incorporated MICRF104 10 November 8, 2001