MOTOROLA MC68160

Order this document by MC68160/D
The MC68160, B and C Enhanced Ethernet Interface Circuit is a BiCMOS
device which supports both IEEE 802.3* Access Unit Interface (AUI) and
10BASE–T Twisted Pair (TP) Interface media connections through external
isolation transformers. It encodes NRZ data to Manchester data and
supplies the signals which are required for data communication via
10BASE–T or AUI interfaces. The MC68160, B and C gluelessly interface to
the Ethernet controller contained in the MC68360 Quad Integrated
Communications Controller (QUICC) device. The MC68160 also interfaces
easily to most other industry–standard IEEE 802.3 LAN controllers.** Prior to
twisted pair data reception, Smart Squelch circuitry qualifies input signals for
correct amplitude, pulse width, and sequence requirements.
•
ENHANCED ETHERNET
INTERFACE TRANSCEIVER
SEMICONDUCTOR
TECHNICAL DATA
Automatic Twisted Pair Wiring Polarity Fault Detection and Correction
Option
•
Automatic Port Selection Option with Status Output
•
Driver Pre–emphasis for Twisted Pair Output Data
•
Crystal Controlled Clock Oscillator or External Clock Generator Option
•
Digital Phase–Locked–Loop (DPLL) Timing Recovery and Data Decoding
•
Standby Mode with Reduced Power Consumption
•
Twisted Pair Signal Quality Error (Heartbeat) Test Option
•
Diagnostic Local Loop Back Option
•
Transmit, Receive and Collision Detection Status Output
•
Full–Duplex Operation Option on Twisted Pair Port
•
Twisted Pair Jabber Detection and Status Output
•
Link Integrity Testing and Status Output
52
FB SUFFIX
PLASTIC PACKAGE
CASE 848D
(TQFP–52)
ORDERING INFORMATION
Device
Operating
Temperature Range
MC68160FB
MC68160BFB
Package
TQFP–52
TA = 0° to + 70°C
MC68160CFB
** MC68160B does not support all IEEE 802.3 specifications over extended
** temperature range. Exceptions noted in specifications.
1
TA = –40° to + 85°C
TQFP–52
TQFP–52
** MC68160B, C only support Motorola controllers
The sale and use of this product is licensed under technology covered by one
or more Digital Equipment Corporation patents.
 Motorola, Inc. 1997
MOTOROLA ANALOG IC DEVICE DATA
Rev 1
1
MC68160 MC68160B MC68160C
Figure 1. 10Base–T Interface Block Diagram
RX
RCLK
Manchester
Decoder
Data
Receiver
Mux
ARX+
MFILT
CLSN
TXLED
Pulse Conditioner
Noise
Reject
Filter
Mux
ARX–
Pulse Conditioner
Noise
Reject
Filter
Collision
Detect
Mux
Pulse
Conditioner
Manchester
Encoder
X1
X2
ATX+
Mux
20 MHz
Osc
Receiver
Mux
÷2
TCLK
ACX+
ACX–
ATX–
TENA
TX
CS0
CS1
CS2
TPEN
APORT
TPAPCE
TPSQEL
TPFULDL
LOOP
Carrier
Detect
Jabber
Control
Driver
Pre–emphasis
Control
Link
Pulse
Control
Mode
Select
TPJABB
TPTX+ TPTX–
TPLIL
Collision
Detector
Control
AUI INTERFACE
SIA INTERFACE
RXLED
RENA
CLLED
Twisted
Pair
Polarity
Error
Control
Receiver
Squelch
Squelch
Test
Circuit
TPSQEL
TPRX–
TPRX+ TPPLR
This device contains 20,000 active transistors.
2
MOTOROLA ANALOG IC DEVICE DATA
MC68160 MC68160B MC68160C
Enhanced Ethernet Serial Transceiver
Table 1. Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Controller Interface Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AUI Interface Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Twisted Pair Interface Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oscillator and Frequency Multiplier Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mode Select Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Status Indicator Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Supply and Ground Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
4
4
5
5
6
6
Table 2. Controller Interface Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Table 3. Controller Independent Mode Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Recommended Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
ESD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Power Supply DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
TTL/CMOS Input and Output DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Twisted Pair Input and Output DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
AUI Input and Output DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
External Clock Input (X1) Switching Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Receive Phase Locked Loop Switching Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Controller Transmit Switching Characteristics (Motorola Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Controller Receive Switching Characteristics (Motorola Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Controller Transmit Switching Characteristics (Intel Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Controller Receive Switching Characteristics (Intel Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Controller Transmit Switching Characteristics (Fujitsu Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Controller Receive Switching Characteristics (Fujitsu Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Controller Transmit Switching Characteristics (National Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Controller Receive Switching Characteristics (National Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TP Transmit Switching Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TP Transmit Jabber Switching Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TP Transmit Signal Quality Error Test Switching Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TP Receive Switching Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TP Receive Link Integrity Switching Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TP Collision Switching Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TP Full Duplex Switching Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AUI Transmit Switching Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AUI Receive Switching Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12
12
12
12
14
14
15
15
16
16
18
20
20
21
21
23
23
24
24
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Data Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Data Reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Collision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Jabber . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Full Duplex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auto Port Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auto Polarity Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Loop Back Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25
26
26
26
26
26
26
26
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Selection of Crystal and External Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PLL Filter Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10BASE–T Filter and Transformer Choice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AUI Transformer Choice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MOTOROLA ANALOG IC DEVICE DATA
3
27
27
27
27
MC68160 MC68160B MC68160C
Table 1. Pin Function Descriptiont
Pin(s)
Symbol
Type
Name/Function
CONTROLLER INTERFACE
1
RENA
O
TTL/CMO
Receive Enable Output: Indication of the presence of network activity, synchronous to
RCLK. In the standby mode, RENA is driven to the high impedance state.
2
RX
O
TTL/CMOS
Receive Data Output: Recovered data, synchronous to RCLK. Following a reset operation,
100 ms should be allowed before attempting to read data processed by the MC68160, B and
C. This delay is needed to insure that the receive phase locked loop is properly synchronized
with incoming data. In the standby mode, RX is driven to the high impedance state.
48
TCLK
O
TTL/CMOS
Transmit Clock Output CMOS/TTL Output: TCLK provides a symmetrical clock signal at
10 MHz for reference timing of data to be encoded. In the standby mode, TCLK is driven to
the high impedance state.
49
TENA
I
TTL
50
RCLK
O
TTL/CMOS
Receive Clock Output: Recovered clock. In the standby mode, RCLK is driven to the high
impedance state.
51
CLSN
O
TTL/CMOS
Collision Output: In the AUI mode, indicates the presence of signals at the ACX+ and
ACX– terminals which meet threshold and pulse width requirements. In the TP mode,
indicates simultaneous transmit and receive activity, a heartbeat (SQE Test) signal was
generated, or the jabber timer has expired. In the standby mode, CLSN is driven to the high
impedance state.
52
TX
I
TTL
Transmit Data Input: Input signal synchronous to TCLK which provides NRZ serial data to
be Manchester encoded. In the standby mode, TX is driven to the high impedance state.
21
22
ACX–
ACX+
I
AUI Differential Collision Inputs: These inputs are connected to a pair of internally biased
line receivers consisting of a carrier detect receiver with offset threshold and noise filtering to
detect the line activity. Signals at ACX+/– have no effect on data path functions.
23
24
ARX–
ARX+
I
AUI Differential Receiver Inputs: These inputs are connected to a pair of internally biased
line receivers consisting of a carrier detect receiver with offset threshold and noise filtering to
detect the line activity, and a data receiver with no offset for Manchester Data reception.
25
26
ATX–
ATX+
O
AUI Differential Transmit Outputs : This line pair is intended to operate into terminated
transmission lines. For TX signals meeting setup and hold time to TCLK when TENA is
previously asserted, Manchester encoded data is outputted at ATX+/–. When operating into a
78 Ω terminated transmission line, signaling meets the required output levels and skew for
IEEE–802.3 drop cables. When the 10BASE–T port is automatically or manually selected,
the AUI outputs are driven to a low power standby state in which the outputs deliver a
balanced high state voltage.
Transmit Enable Input: Input signal synchronous to TCLK which enables data transmission
on the active port. An internal pull–down resistor is provided so that the input is low under no
connect conditions. (This resistor is removed in the standby mode). If TENA is asserted at
the conclusion of a reset operation, it must first be deasserted and then reasserted before
data transmission can occur. In the standby mode, TENA is driven to the high impedance
state.
AUI INTERFACE
TWISTED PAIR INTERFACE
31
32
TPRX–
TPRX+
I
Twisted Pair Differential Receiver Inputs: These inputs are connected to a receiver with
Smart Squelch capability which only allows differential receive data to pass as long as the
input amplitude is greater than a minimum signal threshold level and a specific pulse
sequence is received. This assures a good signal to noise ratio while the signal pair is active
by preventing crosstalk and impulse noise conditions from activating the receive function.
36
37
TPTX–
TPTX+
O
Twisted Pair Differential Transmitter Outputs: These lines have pre–distortion drive
capability and are intended to drive terminated twisted pair transmission lines. When the AUI
port is manually selected, the 10BASE–T outputs are driven to a low power standby state in
which the outputs deliver a balanced high state voltage. However, when the AUI port is
automatically selected, the 10BASE–T outputs remain active.
NOTE:
4
The sense of the controller interface pins will change, depending on the controller selected.
MOTOROLA ANALOG IC DEVICE DATA
MC68160 MC68160B MC68160C
Table 1. Pin Function Description (continued)
Pin(s)
Symbol
Type
Name/Function
OSCILLATOR AND FREQUENCY MULTIPLIER
12
MFILT
C
Frequency Multiplier Filter Connection Point: An external resistor capacitor filter must be
attached to this pin.
16
X1
I/C
CMOS
Oscillator Inverter Input and Crystal Connection Point: When connected for crystal
oscillator operation, the frequency of the clock which appears at TCLK is half that of the
crystal oscillator. As an option, instead of connecting to a crystal, X1 may be driven from an
external 20 MHz CMOS compatible clock generator.
17
X2
O/C
CMOS
Oscillator Inverter Output and Crystal Connection Point: This pin is used only for the
connection of an external crystal and capacitor. It must be left unconnected if X1 is driven by
an external CMOS Clock generator.
3
4
5
CS0
CS1
CS2
I
TTL
Mode Select: The logic states applied to these pins select the appropriate interface for the
desired IEEE–802.3 controller or enable the standby mode. When the standby mode is
selected, the MC68160, B and C power supply current is greatly reduced. Additionally, in the
standby mode, all of the controller inputs and outputs are driven to the high impedance state.
6
LOOP
I
TTL
Diagnostic Loopback: Asserting this function causes serial NRZ data at the TX input to be
Manchester encoded and then looped back through the Manchester decoder, appearing at
the RX output. This diagnostic loopback function operates independent of Twisted Pair (TP)
or Access Unit Interface (AUI) port connectivity or activity. Neither the TP port nor the AUI
port transmits data from the controller while diagnostic loopback is selected. Likewise, the
controller interface receives data neither from the TP nor the AUI receivers while in this
mode. The polarity fault detection and link integrity functions are not inhibited by the
diagnostic loopback mode. If otherwise enabled, they continue to function. If the twisted pair
port is selected, and TPSQEL is driven to the low logic state, a collision detect pulse is
delivered following each transmission to simulate the twisted pair SQE test.
9
APORT
I
TTL
Automatic Port Selection Enable: When high, MC68160, B and C will automatically select
the TP or AUI port based on the presence or absence of valid link beats or frames at the TP
receive input. If the AUI port is automatically selected, the MC68160, B and C will continue to
produce link pulses for the TP port. Changing ports requires approximately 1.0 ms to allow
the circuitry
for the new port to resume normal operation. The power consumption is minimized in the
circuitry associated with the unselected port.
27
TPSQEL
I
TTL
Twisted Pair Signal Quality Error Test Enable: Forcing this pin low enables testing of the
internal TP collision detect circuitry after each transmit operation to the TP media. This
function provides a simulated collision to as much of the MC68160, B and C collision detect
circuitry as possible without affecting the attached twisted pair channel. A normal SQE test
results in a high logic state at the CLSN controller interface pin which begins 6 to 16–bit
times after the last transition of a transmitted signal and continues for 5 to 15–bit times.
(When the AUI port is selected, SQE test signals are generated by the coaxial cable
transceiver and delivered to the controller via the MC68160, B and C ACX+/– receive inputs)
28
TPFULDL
I
TTL
Twisted Pair Full Duplex Mode Select: Forcing this pin low allows simultaneous transmit
and receive operation on the twisted pair port without an indicated collision. This pin is not to
be asserted with LOOP as a test mode is enabled that disrupts normal operation.
29
TPAPCE
I
TTL
Twisted Pair Automatic Polarity Correction Enable: When TPAPCE is high, automatic
polarity correction is enabled, and MC68160, B and C will internally correct for a polarity fault
on the receive circuit. Additionally, when TPAPCE is high, the presence of a polarity fault is
indicated on TPPLR.
46
TPEN
I/O
TTL
(TTL/CMOS)
Twisted Pair Port Enable: If APORT is low, TPEN is an input which determines whether the
AUI port (TPEN low) or TP port (TPEN high) will be manually selected. If the AUI port is
manually selected, the MC68160, B and C will not produce link pulses for the TP port.
MODE SELECT
If APORT is high, TPEN is an output which will indicate which port has been automatically
selected by driving TPEN low (for AUI) or high (for TP). In its output mode TPEN can sink
10 mA in the low output state and source 10 mA in the high output state. (See Pin 9
Description.)
Changing ports requires approximately 1.0 ms to allow the circuitry for the new port to
resume normal operation. The power consumption is minimized in the circuitry associated
with the unselected port. In the standby mode, this pin is driven to the high impedance state.
MOTOROLA ANALOG IC DEVICE DATA
5
MC68160 MC68160B MC68160C
Table 1. Pin Function Description (continued)
Pin(s)
Symbol
Type
Name/Function
STATUS INDICATOR
40
TXLED
O
TTL/CMOS
Transmit Status LED Driver Output: This pin indicates the transmit status of the currently
selected TP or AUI port. When there is no transmit activity detected, an internal pull–up takes
this pin to its normal off (high) state. When transmit activity is detected, the LED driver turns
on. In its on state, TXLED flashes the LED by driving low at approximately 10 Hz at a 50%
duty cycle. In the standby mode, this output is driven to the high impedance state.
41
RXLED
O
TTL/CMOS
Receive Status LED Driver Output: This pin indicates the receive status of the currently
selected TP or AUI port. When there is no receive activity detected, an internal pull–up takes
this pin to its normal off (high) state. When receive activity is detected, the LED driver turns
on. In its on state, RXLED flashes the LED by driving low at approximately 10 Hz at a 50%
duty cycle. In the standby mode, this output is driven to the high impedance state.
42
CLLED
O
TTL/CMOS
Collision Status LED Driver Output: This pin indicates the collision status of the currently
selected TP or AUI port. When there is no collision activity detected, an internal pull–up takes
this pin to its normal off (high) state. When collision activity is detected, the LED driver turns
on. In its on state, CLLED flashes the LED by driving low at approximately 10 Hz at a 50%
duty cycle. In the standby mode, this output is driven to the high impedance state.
43
TPLIL
O
TTL/CMOS
Twisted Pair Link Integrity Output: This output is driven to the low output state to indicate
good link integrity on the TP port during TP mode. It is deasserted (high) when link integrity
fails in TP mode. The TPLIL output is driven to the high impedance state when the AUI port
is selected. In the standby mode, this output is also driven to the high impedance state.
44
TPPLR
O
TTL/CMOS
Twisted Pair Polarity Error Output: If TPAPCE is high and the wires connected to the
Twisted Pair Receiver Inputs (TPRX+, TPRX–) are reversed, TPPLR will be driven to the low
logic state to indicate the fault. TPPLR remains low when the MC68160, B and C has
automatically corrected for the reversed wires. If the twisted pair link integrity tests fail, this
output will be driven to the high logic state. When the AUI mode is selected this output is
driven to the high impedance state. In the standby mode, this output is also driven to the high
impedance state.
45
TPJABB
O
TTL/CMOS
Twisted Pair Jabber Output: This pin is driven high to indicate a jabber condition at the
TPTX+/– outputs. (Jabber condition also causes CLLED to be driven alternately to the high
and low output levels). TPJABB is driven to the low output state when no jabber condition is
present. When the AUI mode is selected this output is driven to the high impedance state. In
the standby mode, this output is also driven to the high impedance state.
POWER SUPPLY AND GROUND
10
VDDDIV
Frequency Divider Supply Pin
11
13
VDDFM
GNDFM
Frequency Multiplier Supply and Ground Pins
14
15
GNDVCO
VDDVCO
Voltage Controlled Oscillator Ground and Supply Pins
20
GNDSUB
Substrate Ground Pin
7
8
18
19
VDDDIG
GNDDIG
VDDDIG
GNDDIG
Digital Supply and Ground Pins
30
33
VDDANA
GNDANA
Analog Supply and Ground Pins
34
35
38
39
GNDPWR
VDDPWR
VDDPWR
GNDPWR
Power Supply and Ground Pins
47
GNDCTL
Controller Interface Ground Pin
NOTE:
6
Power and ground pins are not connected internally. Failure to connect externally may cause malfunction or damage to the IC.
MOTOROLA ANALOG IC DEVICE DATA
MC68160 MC68160B MC68160C
Table 2. Controller Interface Selection
Motorola
Transceiver
MC68160,
B and C
(EEST)
Motorola
Controller2
MC68360
(QUICC)
Intel4
Controllers
82586, 82590,
82593, 82596
Fujitsu4
Controllers
86950 (Etherstar)
86960 (NICE)
National4
Controllers
8390, 83C690,
83932B (SONIC)
CS0
CS1
CS2
1
1
0
0
1
0
1
0
0
0
0
0
Pin
Pin
Sense
Pin
Sense
Pin
Sense
Pin
Sense
TCLK
TCLK
High
TXC
Low
TCKN
Low
TXC
High
TX
TX
High
TXD
High
TXD
High
TXD
High
TENA
TENA
High
RTS
Low
TEN
High
TXE
High
RCLK
RCLK
High
RXC
Low
RCN
Low
RXC
High
RX
RX
High
RXD
High
RXD
High
RXD
High
RENA
RENA
High
CRS
Low
XCD
High
CRS
High
CLSN
CLSN
High
CDT
Low
XCOL
Low
COL
High
LOOP1
N.A.
High
LPBK
Low
LBC
High
LPBK
High
NOTES: 1. Although LOOP input is not ordinarily classifed as a controller pin, it is included in this table because its sense varies according to the controller used.
2. The Motorola controller interface contained in the MC68360 (QUICC) is compatible with the AMD 7990 (LANCE) and 79C900 (ILACC) controllers.
3. The pin sense is shown from the perspective of the identified controller pin.
4. Supported only by MC68160.
Table 3. Controller Independent Mode Selection
Pin
Standby Mode
Reserved
Reserved
Reserved
CS0
CS1
CS2
1
1
1
0
1
1
1
0
1
0
0
1
NOTE: In standby mode, the MC68160, B, C consumes less power supply current than in any
other mode. Additionally, in the standby mode, all of the controller inputs and outputs
are driven to the high impedance state. When the standby mode is deasserted, an
internal reset pulse of approximately 6.0 µs duration is generated.
Following a period of operation in the standby mode, the time required to insure stable
data reception is approximately 100 ms.
Figure 2. Applications Block Diagram
ATX+
ATX+
ATX–
ATX–
ARX+
ARX+
TCLK
ARX–
TX
Pulse
Transformers
ARX–
ACX+
ACX+
ACX–
ACX–
TPTX+
TPTX+
DB–15
Connector
TENA
LAN
Controller
RCLK
MC68160, B, C
RX
RENA
CLSN
TPTX–
TPRX+
TPRX–
MOTOROLA ANALOG IC DEVICE DATA
Filters
and
Pulse
Transformers
TPTX–
TPRX+
RJ–45
Connector
TPRX–
7
MC68160 MC68160B MC68160C
ELECTRICAL CHARACTERISTICS
MAXIMUM RATINGS
Characteristic
Symbol
Min
Max
Unit
Storage Temperature Range
Tstg
– 65
150
°C
Power Supply Voltage Range
Analog
Digital
VDDA
VDDD
–
–
7.0
7.0
V
V
– 0.5
VDD + 0.5
V
– 0.5
6.0
– 6.0
6.0
Voltage on any TTL compatible input pin with
respect to Ground
Voltage on TPRX, ARX, or ACX input pins with
respect to Ground
Differential Voltage on TPRX, ARX, or ACX Input
Pins
NOTE:
VDIFF
V
Stresses in excess of the Absolute Maximum Ratings can cause permanent damage to the
device. Functional operation of the device is not implied at these or any other conditions in
excess of those indicated in the operation sections of this data sheet. Exposure to Absolute
Maximum Ratings conditions for extended periods can adversely affect device reliability.
RECOMMENDED OPERATING CONDITIONS
Characteristic
Symbol
Min
Max
Unit
VDD
4.75
5.25
V
Power Supply Ripple (20 kHz to 100 kHz)
–
–
50
mV
Power Supply Impulse Noise (Either Polarity)
–
–
100
mV
Ambient Operating Temperature Range (MC68160, MC68160C)
TA
0
70
°C
Ambient Operating Temperature Range (MC68160B)
TA
–40
85
°C
ARX/ACX Input Differential Rise and Fall Time (see Figure 39)
t260
2.0
10
ns
ARX Pair Idle Time after Transmission (see Figure 39)
t265
8.0
–
µs
Power Supply Voltage Range
ESD
Although protection circuitry has been designed into this device, proper precautions should be taken to avoid exposure to electrostatic discharge
(ESD) during handling and mounting. Motorola employs a Human Body Model (HBM) and a Charged Device Model (CDM) for ESD–susceptibility
testing and protection design evaluation. ESD has been adopted for the CDM, however, a standard HBM (resistance = 1500 Ω capacitance –
100 pF) is widely used and, therefore, can be used for comparison purposes. The HBM ESD threshold presented here was obtained by using
the circuit parameters contained in this specification. ESD threshold voltage is designed to 700 kV Human Body Model.
DC ELECTRICAL CHARACTERISTICS (Unless otherwise noted, minimum and maximum limits apply over the recommended
ambient operating temperature and power supply voltage ranges.)
Characteristic
Symbol
Test Conditions
Min
Typ
Max
Unit
–
–
–
–
4.4
V
IDD
–
Standby Mode
–
–
145
–
200
5.0
mA
POWER SUPPLY
Undervoltage Shutdown Threshold
Power Supply Current
8
MOTOROLA ANALOG IC DEVICE DATA
MC68160 MC68160B MC68160C
DC ELECTRICAL CHARACTERISTICS (TA = 25°C, VCC = 5.0 V ± 5%. Unless otherwise noted, minimum and maximum
limits apply over the recommended ambient operating temperature and power supply voltage ranges for each MC68160, B, C except where
noted.)
Characteristic
Symbol
Test Conditions
Min
Max
Unit
–
2.0
0.8
–
–
±10
–
–
–
+200
– 20
±10
–
3.0
1.0
–
0 V < VI < VDD
–
±100
IOL = 4.0 mA
IOL = 10 mA
–
–
0.45
0.45
3.9
3.9
2.4
–
–
–
–
±10
µA
Min
Max
Unit
TTL COMPATIBLE INPUTS
TTL Compatible Input Voltage
Low State
High State
Input Current TTL Compatible Input Pins (Note 1)
Input Current TENA TTL Compatible Input Pin:
with Pull–Down Resistor
IIH
IIL
with Pull–Down Resistor removed in Standby Mode
–
VIL(TTL)
VIH(TTL)
0 V < VI < VDD
IIH
IIL
IIH & IIL
V
µA
CMOS COMPATIBLE INPUTS
CMOS Compatible Input Voltage
Low State
High State
Input Current (Pin X1)
–
VIL(CMOS)
VIH(CMOS)
IIH & IIL
V
µA
TTL/CMOS COMPATIBLE OUTPUTS
TTL/CMOS Compatible Output Voltage
Low State (Note 2)
Low State (Note 3)
VOL
TTL/CMOS Compatible Output Voltage
High State (Note 4)
High State (Note 5)
High State (Note 2)
VOH
Three State Output Leakage Current
IOZ
IOH = – 500 µA
IOH = – 10 mA
IOH = – 4.0 mA
0 V ≤ VOZ ≤ VDD
Symbol
Test Conditions
VITP
VITPSQ
–
1.5
4.3
V
Note 10
270
390
mV
Differential Input Squelch Threshold Voltage
(MC68160B)
VITPSQ
Note 10
260
400
mV
Common Mode Bias Generator Voltage
VBCMTP
RCMTP
Note 9
1.8
3.2
V
Common Mode Input Resistance
–
1000
–
Ω
Differential Input Resistance
RDIFFTP
–
2.5
–
kΩ
± 2.2
±1.56
±1.38
±2.8
±1.98
±1.98
Characteristic
V
V
TWISTED PAIR RECEIVER INPUTS
Input Voltage Range (DC + AC)
Differential Input Squelch Threshold Voltage (MC68160,
MC68160C)
TWISTED PAIR TRANSMITTER OUTPUTS
Differential Output Voltage
Pre–Emphasis Level
Signal Level (MC68160, MC68160C)
Signal Level (MC68160B)
Common Mode Output Voltage Range
Common Mode Output Voltage in Standby Mode
Note 7
V
VODFTPP
VODFTPS
VODFTPS
VOCMTP
Note 6
0
4.0
V
VOCMTPSB
IOH = –100 µA
VDD – 1.0
VDD
V
NOTES: 1. APORT, TPAPCE, CS0, CS1, CS2, TX, LOOP, TPFULDL, TPSQEL and TPEN (In Input Mode).
2. TCLK, RX, RCLK, RENA and CLSN.
3. TPPLR, TPLIL, TPJABB, TXLED, RXLED, CLLED and TPEN (In Output Mode).
4. TPPLR, TPLIL, CLLED, TXLED and RXLED.
5. TPJABB and TPEN (In Output Mode).
6. Measured with Test Load B1 (shown in Figure 3), applied directly to the TPTX+/– pins of the device.
7. Measured differentially with Test Load B2 (shown in Figure 4), applied directly to the TPTX+/– pins of the device.
8. Measured directly on the TPTX+/– pins of the device.
9. Measured with Test Load B3 (shown in Figure 5), applied directly to the TPRX+/– pins of the device.
10. The Common Mode Input Voltage is between 1.8 V and 3.2 V.
MOTOROLA ANALOG IC DEVICE DATA
9
MC68160 MC68160B MC68160C
DC ELECTRICAL CHARACTERISTICS (continued) (TA = 25°C, VCC = 5.0 V ± 5%. Unless otherwise noted, minimum and maximum
limits apply over the recommended ambient operating temperature and power supply voltage ranges for each MC68160, B, C except where
noted.)
Symbol
Test Conditions
Min
Max
Unit
Differential Output Voltage
IDLE Mode
Open Circuit
VODFTPI
VODFTPO
Note 6
Note 8
–
–
±50
5.25
mV
V
Differential Output Impedance
TRANSMISSION Mode
IDLE Mode
RODFTPT
RODFTPI
12
8.0
28
29
Common Mode Output Impedance
TRANSMISSION Mode (MC68160, MC68160C)
TRANSMISSION Mode (MC68160B)
IDLE Mode
ROCMTPT
ROCMTPT
ROCMTPI
3.0
2.5
1.0
7.0
7.0
10
Characteristic
TWISTED PAIR TRANSMITTER OUTPUTS
Ω
Note 8
Note 8
Ω
kΩ
NOTES: 1. APORT, TPAPCE, CS0, CS1, CS2, TX, LOOP, TPFULDL, TPSQEL and TPEN (In Input Mode).
2. TCLK, RX, RCLK, RENA and CLSN.
3. TPPLR, TPLIL, TPJABB, TXLED, RXLED, CLLED and TPEN (In Output Mode).
4. TPPLR, TPLIL, CLLED, TXLED and RXLED.
5. TPJABB and TPEN (In Output Mode).
6. Measured with Test Load B1 (shown in Figure 3), applied directly to the TPTX+/– pins of the device.
7. Measured differentially with Test Load B2 (shown in Figure 4), applied directly to the TPTX+/– pins of the device.
8. Measured directly on the TPTX+/– pins of the device.
9. Measured with Test Load B3 (shown in Figure 5), applied directly to the TPRX+/– pins of the device.
10. The Common Mode Input Voltage is between 1.8 V and 3.2 V.
DC ELECTRICAL CHARACTERISTICS (Unless otherwise noted, minimum and maximum limits apply over the recommended
ambient operating temperature and power supply voltage ranges for each MC68160, B, C except where noted.)
Characteristic
Symbol
Test Conditions
Min
Max
Unit
VIA
–
1.0
4.2
V
Differential Mode Input Voltage Range
VIDFA
–
±318
±1315
mV
Differential Input Squelch Threshold Voltage
(MC68160, MC68160C)
VIASQ
–
– 275
–175
mV
Differential Mode Input Voltage Range (MC68160B)
VIASQ
–
– 300
–175
mV
Common Mode Input Resistance
RICMA
1.0 V < VICMA < 4.2 V
1.5
–
kΩ
Differential Input Resistance (ARX, ACX Inputs)
RIDFA
1.0 V < VICMA < 4.2 V
318 mV < VIDMA < 1315 mV
5.0
–
kΩ
1.0
1.0
VDD – 2.0
4.2
4.2
VDD – 1.2
–
±600
±40
±1315
–
±4.0
–
±150
AUI RECEIVER INPUTS
Input Voltage Range (DC + AC)
AUI TRANSMITTER OUTPUTS
Common Mode Output Voltage
IDLE Mode
ACTIVE Mode
STANDBY Mode
VOCMIA
VOCMAA
VOCMSA
Figure 6
Differential Output Voltage
IDLE Mode
ACTIVE Mode
VODFIA
VODFAA
IO = –100 µA
Figure 6
Differential Output Load Current
IDLE Mode
IODFIA
Output Short Circuit Current
IODSA
10
V
mV
Figure 7
mA
Output Short Circuited to
VDD or GND
mA
MOTOROLA ANALOG IC DEVICE DATA
MC68160 MC68160B MC68160C
Figure 3. Test Load B1
Device
V1
39 Ω
RCM
1.0 k Ω
39 Ω
Figure 4. Test Load B2
+
VCMD
–
Device
39 Ω
100 Ω
39 Ω
Figure 5. Test Load B3
39 Ω
Device
39 Ω
NOTE:
RCM
10 kΩ
+
VCMD
–
A total of 50 Ω per driver output is required for proper series line termination. This is realized with the
39 Ω external resistors shown in Figures 3, 4 and 5, together with the internal driver output resistance.
Figure 6. AUI Common Mode Termination
Figure 7. AUI Differential Output
Short Circuit Current
–
39 Ω
IO
VCM
VDIFF
IOD
39 Ω
+
MOTOROLA ANALOG IC DEVICE DATA
11
MC68160 MC68160B MC68160C
AC ELECTRICAL CHARACTERISTICS (Unless otherwise noted, minimum and maximum limits apply over the recommended
temperature and power supply voltage ranges for each MC68160, B, C except where noted.)
Characteristic
Symbol
Min
Max
Unit
t1
t2
t3
t4
t5
49.995
–
–
20
20
50.005
5.0
5.0
30
30
ns
t7
–
100
ms
TCLK Cycle Time
TCLK High Time
TCLK Low Time
TCLK Rise and Fall Time
t10
t11
t12
t13
99
45
45
–
101
55
55
8.0
ns
TX Setup Time to TCLK ↑
TX Hold Time to TCLK ↑
t14
t15
20
0
–
–
ns
TENA Setup Time to TCLK ↑
TENA Hold Time to TCLK ↑
t16
t17
20
0
–
–
ns
t20
t21
t22
t22
t23
90
42
47
44
–
–
–
55
58
8.0
ns
t24
t24.1
10
70
–
–
ns
RCLK Delay from RENA ↑
RX Delay from RENA ↑
t25
t26
–
–
650
600
ns
RENA Deassertion Delay from RCLK ↑ (See Figure 12)
t27
10
30
ns
EXTERNAL CLOCK INPUT (X1)
Cycle Time (Note 1) (See Figure 8)
Fall Time
Rise Time
Low Time
High Time
RECEIVE PHASE–LOCKED–LOOP SWITCHING
Stabilization Time
CONTROLLER TRANSMIT SWITCHING (MOTOROLA MODE)
CONTROLLER RECEIVE SWITCHING
RCLK Cycle Time
RCLK High Time
RCLK Low Time (MC68160, MC68160C)
RCLK Low Time (MC68160B)
RCLK Rise and Fall Time
RX Hold Time from RCLK ↑
RX Set–Up Time to RCLK ↑
NOTES: 1. To meet IEEE–802.3 specifications.
2. Load on specified output is 20 pF to ground, unless otherwise noted.
3. ↑ = Rising Edge
Figure 8. X1 Input Voltage Levels for Timing Measurements
t1
t2
4.0V
1.5V
0V
3.6V
1.5V
t5
3.6V
1.5V
0.4V
0.4V
t4
t3
12
MOTOROLA ANALOG IC DEVICE DATA
MC68160 MC68160B MC68160C
Figure 9. Receive Phase–Locked–Loop Switching
CS0 D CS1 D CS2
1.5V
TPRX
t7
1.5V
RENA
NOTE:
CS0 • CS1 • CS2 is the logical AND operation and refers to the pins not at Logic 1.
Figure 10. Transmit Timing (Motorola Mode)
t13
t11
1.5V
1.5V
3V
t13
0.8V
3V
1.5V
1.5V
1.5V
1.5V
TCLK
t10
t16
t17
t12
1.5V
1.5V
TENA
t14
t15
TX
1.5V 1.5V
Figure 11. Receive Timing (Motorola Start of Frame)
1.5V
t23
RENA
t23
t22
t21
t25
1.5V
3V
0.8V
RCLK
t26
RX
MOTOROLA ANALOG IC DEVICE DATA
3V 1.5V
0.8V
t24.1
1.5V
t24
1.5V
1.5V
1.5V
t20
1.5V
13
MC68160 MC68160B MC68160C
Figure 12. Receive Timing (Motorola End of Frame)
RENA
1.5V
t27
1.5V
RCLK
RX
Last Bit
CONTROLLER TRANSMIT SWITCHING (Intel Mode – Support by MC68160 Only)
Symbol
Min
Max
Unit
TXC Cycle Time
TXC High and Low Time
TXC Rise and Fall Time
t40
t41
t42
99
40
–
101
–
5.0
ns
TXD Setup Time to TXC ↓
TXD Hold Time to TXC ↓
t43
t44
20
0
–
–
ns
RTS Setup Time to TXC ↓
RTS Hold Time to TXC ↓
t45
t46
20
0
–
–
ns
t80
t81
t82
t83
90
45
40
–
–
55
–
5.0
ns
t85
t85.1
t86
50
35
12
–
–
30
ns
Characteristic
CONTROLLER RECEIVE SWITCHING
RXC Cycle Time
RXC High Time
RXC Low Time
RXC Rise and Fall Time
RXD Hold Time from RXC ↓
RXD Set–Up Time to RXC ↓
CRS Delay from RXC ↑
NOTE:
Load on specified output is 20 pF to ground, unless otherwise noted.
↑ = Rising Edge
↓ = Falling Edge
Figure 13. Transmit Timing (Intel)
t42
TXC
3V
t42
0.8V
t41
3V
1.5V
1.5V
1.5V
1.5V
t41
t45
RTS
1.5V
1.5V
t40
t46
1.5V
1.5V
t43
t43
t44
TXD
1.5V
1.5V
1
14
0
0
0
1.5V
1
Last Bit
1/0
MOTOROLA ANALOG IC DEVICE DATA
MC68160 MC68160B MC68160C
Figure 14. Receive Timing (Intel)
CRS
1.5V
t81
t82
1.5V
1.5V
t85.1
t85
t86
t80
1.5V
1.5V
.8V
3V
RXC
t83
3V
t83
RXD
1.5V
1.5V
CONTROLLER TRANSMIT SWITCHING (Fujitsu Mode – Supported by MC68160 Only)
Symbol
Min
Max
Unit
TCKN Cycle Time
TCKN High and Low Time
TCKN Rise and Fall Time
t90
t91
t92
99
45
–
101
55
8.0
ns
TXD Setup Time to TCKN ↓
TXD Hold Time to TCKN ↓
t93
t94
20
0
–
–
ns
TEN Setup Time to TCKN ↓
TEN Hold Time to TCKN ↓
t95
t96
20
0
–
–
ns
t100
t101
t102
t103
90
40
45
–
–
–
55
8.0
ns
t104
t104.1
t105
50
35
–
–
–
600
ns
t106
0
–
ns
Characteristic
CONTROLLER RECEIVE SWITCHING
RCKN Cycle Time
RCKN High Time
RCKN Low Time
RCKN Rise and Fall Time
RXD Hold Time from RCKN ↓
RXD Set–Up Time RCLK ↓
RCKN Delay from XCD ↑
XCD Deassertion Delay from RCKN ↑ (See Figure 17)
NOTE:
Load on specified output is 20 pF to ground, unless otherwise noted.
↑ = Rising Edge
↓ = Falling Edge
Figure 15. Transmit Timing (Fujitsu)
t91
t90
TCKN
1.5V
1.5V
1.5V
1.5V
t95
t91
1.5V
3V
0.8V
t92
0.8V
t92
1.5V
t96
1.5V
TEN
t93
1.5V
t94
1.5V
TXD
MOTOROLA ANALOG IC DEVICE DATA
15
MC68160 MC68160B MC68160C
Figure 16. Receive Timing (Fujitsu Start of Frame)
1.5V
XCD
t105
t101
1.5V
1.5V
1.5V
t104.1
t102
RXD
1.5V
t100
3V
0.8V
RCKN
t104
t103
1.5V
1.5V
t103
1.5V
Figure 17. Receive Timing (Fujitsu End of Frame)
XCD
1.5V
t106
1.5V
RCKN
RXD
CONTROLLER TRANSMIT SWITCHING (National Mode – Supported by MC68160 Only)
Symbol
Min
Max
Unit
TXC Cycle Time
TXC High and Low Time
TXC Rise and Fall Time
t110
t111
t112
99
45
–
101
55
8.0
ns
TXD Setup Time to TXC ↑
TXD Hold Time to TXC ↑
t113
t114
20
0
–
–
ns
TXE Setup Time to TXC ↑
TXE Hold Time to TXC ↑
t115
t116
20
0
–
–
ns
t120
t121
t122
t123
90
40
40
–
–
–
60
8.0
ns
t124
t124.1
t125
50
35
–
–
–
600
ns
CRS Deassertion Delay from RXC ↓
t126
0
15
ns
RXC continuing beyond CRS ↓
t127
5.0
–
cycles
Characteristic
CONTROLLER RECEIVE SWITCHING
RXC Cycle Time
RXC Low Time
RXC High Time
RXC Rise and Fall Time
RXD Hold Time from RXC ↑
RXD Set–Up Time from RXC ↑
RXC Delay from CRS ↑
NOTE:
16
Load on specified output is 20 pF to ground, unless otherwise noted.
↑ = Rising Edge
↓ = Falling Edge
MOTOROLA ANALOG IC DEVICE DATA
MC68160 MC68160B MC68160C
Figure 18. Transmit Timing (National)
t111
1.5V
t110
1.5V
1.5V
3V
0.8V
0.8V
1.5V
TXC
t116
t111
t112
t115
t112
1.5V
1.5V
TXE
t113
1.5V
t114
1.5V
TXD
Figure 19. Receive Timing (National)
1.5V
1.5V
CRS
t125
t126
t122
t127
t120
RXC
1.5V
1.5V
t121
3V
0.8V
t123
t123
1.5V
1.5V
1.5V
t124.1 t124
1.5V
RXD
MOTOROLA ANALOG IC DEVICE DATA
17
MC68160 MC68160B MC68160C
TP TRANSMIT SWITCHING
Symbol
Min
Typ
Max
Unit
VOCMTP
–
–
50
mVrms
TX to TPTX Steady State Propagation Delay (Note 2) (See Figure 24)
Bit Duration Center–to–Center
Half–Bit Cell Duration Center–to–Boundary
t130
t131
t132
–
98
48
–
–
–
200
102
52
ns
TENA Assert to RENA Assert Delay (Note 7) (See Figure 24)
t133
–
–
400
ns
Internal Loopback Delay from TX to RX (Note 7) (See Figure 24)
(MC68160, MC68160C)
(MC68160B)
t134
t134
–
–
–
–
450
650
t135
250
–
400
TPTX Precompensation Pulse Width (Notes 2 and 6) (See Figure 25)
(MC68160, MC68160C)
(MC68160B)
t136
t136
–
–
45–58
38–58
–
–
RENA Deassert Delay from TENA Deassert when Receiver is inactive
Motorola Mode (MC68160, MC68160C)
Motorola Mode (MC68160B)
Fujitsu Mode (MC68160 Only)
National Mode (MC68160 Only)
Intel Mode (Note 4) (See Figure 26) (MC68160 Only)
t137
t137
t137
t137
t138
250
250
250
250
250
–
–
–
–
–
450
500
450
450
450
TPTX Data–to–Link Test Pulse (Note 2) (See Figure 27)
TPTX Link Test Pulse Width (Note 2)
TPTX Link Test Pulse Decay–to–Idle Condition (Note 1)
TPTX Link Test Pulse to next Link Test Pulse (Note 2)
t139
t140
t141
t142
8.0
80
80
8.0
–
–
–
–
24
240
240
24
Characteristic
TPTX Common Mode AC Output Voltage (Note 3)
TPTX End of Packet Hold Time from last positive TPTX Signal Edge to
+585 mV Differential Output Level (Note 5) (See Figure 25)
NOTES: 1.
2.
3.
4.
5.
6.
7.
ns
ns
ns
ns
ms
ns
ns
ms
Measured differentially across the output of Test Load A which is connected directly to the TPTX+/– pins of the device.
Measured differentially across the output of Test Load D shown in Figure 23 which is connected directly to the TPTX+/– pins of the device.
Measured across the output of Test Load C which is connected directly to the TPTX+/– pins of the device.
Same as t137 except the logic states for TENA and RENA are inverted.
Measured across the output of Test Load B shown in Figure 21.
Measured at the +/–90% points of the precompensation voltage feature of the waveform. (The 0% reference is 0 V differential.)
Load on specified output is 20 pF to ground.
Figure 20. Test Load A
Figure 21. Test Load B
100µH
1.0µH
39Ω
39Ω
100pF
39Ω
100pF
1.0µH
100Ω
VOUT
Figure 22. Test Load C
Device
Figure 23. Test Load D
200µH
200µH
39Ω
Vout
39Ω
47.5Ω
39Ω
47.5Ω
39Ω
100Ω
49.9Ω
NOTE:
18
100Ω
39Ω
VOUT
VCM
A total of 50 Ω per driver output is required for proper series line termination.
This is realized with the 39 Ω external resistors shown in Figures 20 to 23,
together with the internal driver output resistance.
MOTOROLA ANALOG IC DEVICE DATA
MC68160 MC68160B MC68160C
Figure 24. TPTX Transmit Timing (Start of Frame) Switching
X1
1.5V
TCLK
TENA
1.5V
1
TX
1.5V
0
1
0
0
1
1
t133
1.5V
RENA
t134
1.5V
RX
TPTX +/– Differential
(Logic Levels)
1
1
0
1
0
1
0
0
0
0
t130
TPTX +/– Differential
(Pre–Emphasis)
1
0
1
t131
0V
1
0
1
0
1
1
t132
1
1
Figure 25. TPTX Transmit Timing (End of Frame) Switching
t136
90%
t135
90%
+585mV
+585mV
TPTX +/–
Differential
Figure 26. RENA Deassert Delay from TENA
t137
TENA
1.5V
RENA
1.5V
MOTOROLA ANALOG IC DEVICE DATA
19
MC68160 MC68160B MC68160C
Figure 27. TPTX+/– Link Pulse Timing
t142
t141
t140
t139
585mV
585mV
585mV
±50mV
TP TRANSMIT JABBER SWITCHING
Symbol
Min
Max
Max Length of Transmission before Assertion
of TPJABB to indicate Jabber Condition
CLSN to indicate Jabber Condition
t160
t161
20
20
60
60
Time from End of Jabber Condition to Deassertion:
of TPJABB
of CLSN
t162
t163
500
500
750
750
CLSN (Signal Quality Error Test) (See Figure 29)
Assertion from last positive
positi e TPTX edge
Deassertion from last positive TPTX edge
Pulse Width
t170
t171
t172
0.6
0
6
–
0.5
1.6
1
6
3.1
1.5
TPSQEL Disable Delay Time (See Figure 29)
t173
–
40
Characteristic
Unit
ms
ms
TP TRANSMIT SIGNAL QUALITY ERROR TEST SWITCHING
NOTE:
µs
ns
The load attached to the specified output is a 20 pF capacitor connected to ground, unless otherwise noted.
Figure 28. TPJABB Switching
TPTX
(Differential)
585mV
–585mV
t160
t162
1.5V
1.5V
TPJABB
t161
t163
1.5V
1.5V
CLSN
20
MOTOROLA ANALOG IC DEVICE DATA
MC68160 MC68160B MC68160C
Figure 29. TPTX SQE (CLSN) Timing (End of Frame)
TPTX+/–
2V
1.5V
TPSQEL
t173
t171
t170
t172
1.5V
1.5V
CLSN
TP RECEIVE SWITCHING
Symbol
Min
Max
Unit
VIDFSTP
0
|264|
mV
Positive or Negative Differential Input Pulse Width for Conditional Receive Unsquelch
(See Figure 31)
t180
20
30
ns
TPRX to RCLK Bit Loss at start of packet (See Figure 32)
t181
–
10
Bits
TPRX to RCLK Steady State Propagation Delay (See Figure 32)
t182
–
400
ns
TPRX to RX Start Up Delay (See Figure 32)
t183
–
1.5
µs
TPRX held high from last valid positive transition (See Figure 33)
t186
230
–
ns
RENA Deassertion Delay from last valid positive transition of TPRX Pair
(MC68160, MC68160C) (See Figure 33)
t187
–
350
ns
RENA Deassertion Delay from last valid positive transition of TPRX Pair (MC68160B)
t187
–
400
ns
Required Pulse Width Range to be recognized as a Link Pulse (Note 2)
t200
50
200
ns
Last TPRX activity to high state TPLIL Output
(Receive Link Loss Timeout Interval)
t201
100
150
ms
t202
t203
3.0
100
7.0
150
Characteristic
Differential Input Voltage Range Unconditional Squelch (Note 1)
(1.8 V < Input Common Mode Voltage < 3.2 V)
TP RECEIVE LINK INTEGRITY SWITCHING
Receive Link Beat Separation
Minimum Range (Note 3)
Maximum Range (Note 4)
NOTES: 1.
2.
3.
4.
ms
Measured with Test Load H attached to the receive pins.
Measured at the receive pins.
Link beats closer in time to this range of values are considered noise, and are rejected.
Link beats further apart in time than this range of values are not considered consecutive, and are rejected.
Figure 30. Test Load H
1.0µH
Figure 31. TPRX Input Switching
200µH
+330mV
t180
100Ω
100pF
100pF
Line
0mV
TPRX
1.0µH
MOTOROLA ANALOG IC DEVICE DATA
–330mV
t180
21
MC68160 MC68160B MC68160C
Figure 32. TPRX Receive Timing (Start of Frame)
Bit n
0
1
TPRX+/–
0V
–300mV
Bit n+1
1
Bit n+2
0
Bit n+3
1
Bit n+4
1
0V
t182
RENA
t183
t181
1.5V
1.5V
RCLK
RX
Bit n
Bit n+1
Bit n+2
Figure 33. RENA Deassertion Delay from Last Valid Positive Transition of TPRX Pair
t186
+300mV
+300mV
0V
TPRX+/–
t187
RENA
1.5V
Figure 34. TP Receive Link Integrity Switching
t202/t203
t200
300mV
TPRX
300mV
t201
50%
TPLIL
22
MOTOROLA ANALOG IC DEVICE DATA
MC68160 MC68160B MC68160C
TP COLLISION SWITCHING
Characteristic
Symbol
Min
Max
Unit
Time from collision (TPRX activity caused assertion of RENA followed by assertion of
TENA) to assertion of CLSN
Time from end of collision (Deassertion of TENA with uninterrupted TPRX pair
activity) to deassertion of CLSN
t210
–
300
ns
t211
350
900
TPFULDL assert to collision detect disable (See Figure 36)
TPFULDL deassert to collision detect enable
t220
t221
–
–
50
50
ns
TPFULDL assert to data loop back disable (See Figure 37)
TPFULDL deassert to data loop back enable
t222
t223
–
–
350
150
ns
TP FULL DUPLEX SWITCHING
NOTE:
Load on specified output is 20 pF to ground, unless otherwise noted.
Figure 35. TPTX Collision Timing
RENA
1.5V
1.5V
TENA
t211
t210
1.5V
1.5V
CLSN
Figure 36. TPTX Full Duplex Timing
TPFULDL
1.5V
1.5V
t220
t221
CLSN
1.5V
1.5V
Figure 37. TPTX Full Duplex Timing
TPFULDL
1.5V
RENA
1.5V
t223
t222
1.5V
MOTOROLA ANALOG IC DEVICE DATA
1.5V
23
MC68160 MC68160B MC68160C
AUI TRANSMIT SWITCHING
Symbol
Min
Typ
Max
Unit
TCLK to ATX Pair Steady State Propagation Delay
t240
–
–
100
ns
Output Differential Rise and Fall Times (Measured directly at device pins)
t241
1.0
–
5.0
ns
ATX Bit Cell Duration center–to–center (Measured directly at device pins)
t242
–
99.5–100.5
–
ns
ATX Half–Bit Cell Duration center–to–boundary (Measured directly at device pins)
t243
–
49.5–50.5
–
ns
ATX Pair Held at Positive Differential at start of Idle (Measured through
transformer)
t244
200
–
–
ns
Characteristic
NOTE:
Load on specified output is a shunt 27 µH inductor and 83 Ω resistor.
Figure 38. ATX Transmit Timings
TCLK
1.5V
TENA
TX
1
0
1
0
0
1
1
t241
t240
t241
90%
ATX+/–
Differential
(Logic Levels)
1
0V
0
1
0
0
10%
t242
t244
90%
1
10%
0V
1
70%
t243
AUI RECEIVE SWITCHING
Symbol
Min
Max
Unit
ARX/ACX Differential Input Voltage Range
–
±318
±1315
mV
ARX/ACX Differential Input Pulse Width to:
Initiate Data Reception
Inhibit Data Reception
t261
t262
30
–
–
18
RENA Assertion Delay
RENA Deassertion Delay
t266
t267
–
–
100
450
Characteristic
ns
ns
Squelching Characteristics
The receive data pairs and the collision pairs should have the following squelch characteristics:
1. The squelch circuits are on at idle (with input voltage at approximately 0 V differential).
2. If an input is in squelch, pulse is rejected if the peak differential voltage is more positive than –175 mV, regardless of pulse width.
3. A pulse is considered valid if its peak differential voltage is more negative than –300 mV and its width, measured at –285 mV, is > 25 ns.
4. The squelch circuits are disabled by the first valid negative differential pulse on either the AUI receive data or collision pair.
5. If a positive differential pulse occurs on either the AUI receive data or collision pair > 175 ns, end of frame is assumed and squelch circuitry is turned on.
Figure 39. ARX/ACX Timing
+175mV
ARX+/–
ACX+/–
Differential
Input Voltage
24
–175mV
t261/ t262
MOTOROLA ANALOG IC DEVICE DATA
MC68160 MC68160B MC68160C
Figure 40. ARX/ACX Timing
Bit Q
ARX+/–/
ACX+/–
Differential
Input Voltage
Bit U
Bit V
Bit W
Bit X
Bit Y
t260
t261
Bit Z
t260
+300mV
–40mV
90%
1
–275mV
–300mV
0
1
0
0
10%
90%
1
10%
0V
1
t266
t267
1.5V
1.5V
RENA/CLSN
RCLK
RX
Bit Q
Bit U
Bit V
Bit U
Bit X
Bit Y
Bit Z
FUNCTIONAL DESCRIPTION
Introduction
The MC68160, B, C (EEST) was designed to perform the
physical connection to the Ethernet media. This is done
through two separate media dependent interfaces and a SIA
interface. The media dependent interfaces are the
Attachment Unit Interface(AUI) and the 10BASE–T Twisted
Pair(TP) port. The MC68160’s SIA interface is compatible
with most industry controllers and selected by three mode
control pins. The MC68160B’s and MC68160C’s SIA
interface supports the Motorola MC68360 only. Chip status is
supported on all versions indicated by the condition of 6
status indicator pins. All but one are open collector outputs.
If the EEST isn’t receiving data, the controller may initiate
transmission. NRZ data from the communications controller
SIA interface is encoded by the MC68160, B, or C into
Manchester Code in preparation for transmission on the
media. The data is then applied to either the AUI or TP port.
If the data was transmitted using the 10BASE–T port, this
data is also looped back to the receive data interface SIA
pins connected to the controller. This allows detection of a
collision condition in the event that another station on the
media attempted transmission at the same time. After the
entire data frame has been transmitted, the EEST must
force the media idle signal. The idle signal frees the media
for other stations that have deferred transmission. If no
other transmissions are required the link enters an idle
state. During this idle state the 10BASE–T transmitter
issues idle pulses which communicates to the receiver
MOTOROLA ANALOG IC DEVICE DATA
connected to the other side that the link is valid. If the
transmitter connected at the other end begins transmission,
the EEST will assert a receive enable signal, and forward
the received data to the controller.
Upon reception of data at the 10BASE–T port, the data is
screened for proper sequence and pulse width requirements.
If the preamble of the received frame meets the
requirements, the PLL locks onto the 64–bit preamble and
begins to decode the Manchester Code to NRZ code. This
code is then presented to the communications controller at
the receive data pins at the SIA interface. If data is received
at the AUI port, it is sent directly to the communications
controller via the SIA interface.
Data Transmission
To have properly encoded transmit data, the com–
munications controller must be synchronized to TCLK.
Transmission to the 10BASE–T or AUI media occurs when
TENA is asserted and data is applied to the TX pin. Finally, to
signify transmission, the TXLED in will cycle on and off at a
100 ms period. Data transmission for EEST is accomplished
either over the 10BASE–T port or the AUI port. Both
connections to the media are made with industry standard
media interface components. The 10BASE–T interface
requires a filter and transformer, the AUI interface requires
only a transformer. The filter for the 10BASE–T transmit
circuit will have to be chosen for each application.
25
MC68160 MC68160B MC68160C
If after approximately 40 ms after a TP or AUI transmission
has begun, the EEST is still transmitting, the TPJABB pin will
assert to signify a jabber condition. Also, the CLLED pin will
transition high and low alternately with a 100 ms period. The
transmit circuitry is, however, unaffected by the jabber
condition, so the communications controller has the
responsibility of monitoring and stopping transmission.
When transmission is complete, the transmit circuitry will
begin the end of transmit and decay to idle responses
necessary to meet requirements of the 802.3 standard for the
TP and AUI port.
Data Reception
Other than the case of being in Loop Back mode, data
reception to the RX pin of the EEST is initiated by signaling at
the RX+/– or AUI ARX+/– pins. If at the TP port, the data is
screened for validity by checking for sequence and pulse
width requirements, then passed to the decode and receive
circuitry. The RENA pin asserts and the data and
corresponding clock is passed to the communications
controller. After the frame has been transmitted, the
MC68160, B and C detects the ending transmission and
negates RENA. If at the AUI port, the data is checked for
proper pulse width requirements before being passed to the
decode circuitry. If the data pulses are longer than at least 20
ns, RENA gets asserted and the frame is decoded to RX with
and accompanying RCLK output.
Collision
Collision is the occurrence of simultaneous transmit
activity by two or more stations on the network. In the event of
collision, the data transfer paths are unaffected. If the
MC68160, B and C is in the twisted pair mode, collision is
detect by simultaneous receive and transmit activity. If in the
AUI mode, collision is detected by activity on the ACX+/–
pins. In either case, if collision is detected, the CLSN pin will
assert to notify the communications controller.
Jabber
The EEST has a jabber timer to detect the jabber condition.
In the event that the transmitting station continues to transmit
beyond the allowable transmit time, a jabber timer (40 ms) will
expire and assert the TPJABB pin to alert the communications
26
controller of the situation. The TPJABB pin can source or sink
up to 10 mA, and so, is capable of driving a status LED. In the
AUI mode, the pin is driven to high impedance since the
transceiver connected to the AUI port must alert the
communications controller of the jabber condition.
Full Duplex
A feature unique to the MC68160, B and C is the Full
Duplex mode. In this mode the EEST is capable of
transmitting and receiving simultaneously. Collision
conditions are not announced and internal loop back is
disabled. The remainder of the EEST functionality remains
unchanged from the non–Full Duplex mode. Full Duplex
mode is enabled by asserting the TPFULDL pin.
Auto Port Selection
If the APORT pin is asserted, the MC68160, B and C will
automatically select the TP or AUI port depending on the
presence of valid link beats or frames at the TP RX+/– pins. If
the AUI port is automatically selected by another transmitting
station or by setting TPEN low, the TP transmit port of the
EEST continues to transmit link beats to keep the link active.
Auto Polarity Selection
If the RX+ and the RX– wires happen to get reversed, the
MC68160, B and C has the ability to automatically reverse the
pins internally so that the received data is valid. In addition, an
open collector status pin (TPPLR) is driven low to indicate the
fault. In the AUI or reset mode this pin presents a high
impedance.
Loop Back Mode
To test the transmit and receive circuitry without disturbing
the connected network, the EEST has a Loop Back mode.
Loop Back mode routes transmit data and clock to the
receive data and clock pins using as much of the transmit and
receive circuitry as possible. This gives a test of the
MC68160, B and C Manchester encode and decode function.
LOOP must not be asserted when TPFULDL pin is asserted.
This causes the MC68160, B and C to enter a test mode. This
test mode is used during final test and is not intended to be
entered under normal operation (see Application Notes
section).
MOTOROLA ANALOG IC DEVICE DATA
MC68160 MC68160B MC68160C
APPLICATIONS INFORMATION
Selection of Crystal and External Components
Accuracy of frequency and stability over temperature are
the main determinants of crystal choice. Specifications for a
suitable crystal are tabulated below.
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
Vendor
Part #
FEE Fil–Mag
78Z1120B–01, 78Z1122B/D–01,
78Z1122 F–01
Valor Electronics
PT3877, FL1012, FL1066
Frequency
20.000 MHz
Pulse Engineering
PE–65434, PE65424, PE65433
Mode
Fundamental
TOKO
PM01–00, PM02–00, PM05–00
Tolerance
± 100 ppm
Stability
± 100 ppm
Aging
± 5 ppm/yr
Shunt Capacitance
7.0 pF
Load Capacitance
18–20 pF
25 Ω
Series Fundamental Resistance (ESR)
500 µW
Drive Level
X1
A suitable crystal is the MTRON
HC49 MP–1, 20.000 MHz crystal.
20 pF for C4 and C5 have been
shown to work reliably.
X2
1
2
C5
C4
PLL Filter Components
The filter components at Pin 12 were chosen to assure
adequate pull–range but with a emphasis on stability. It is not
foreseeable that a design would need to change the
components, but for the sake of completeness, relevant
values are provided here.
+ 24
ǒ
Ǔ
ǒǓ
MHz
and,
Volt • sec
100 mA and the
Phase Detector Gain
p 2 rad
VCO Gain
+ ń
filter impedance function is;
(jw ) 1ńC6)
Z(jw) [
jw • C5 • (jw ) 1ńC5)
(for C6
uu C5)
10BASE–T Filter and Transformer Choice
The MC68160, B and C differential outputs are low
impedance voltage sources. Therefore, external series
resistors must be used in order to match the characteristic
impedance of twisted pair. Since the output resistance of
each leg of the transmitter is about 10 Ω, a 39 Ω resistor is
used in series as shown in the applications schematic. So the
impedance presented from the source to the isolation
transformer is then very nearly 100 Ω. The following is a list of
some 10BASE–T filter module vendors and their products.
MOTOROLA ANALOG IC DEVICE DATA
AUI Transformer Choice
Like the 10BASE–T outputs, the AUI differential outputs
are low impedance sources and capable of meeting the IEEE
802.3 waveform requirements when a coupling transformer
is used. Some AUI transformer vendors and their products
are provided below.
Vendor
Part #
Coilcraft
LAX–ET304
FEE Fil–Mag
23Z90, 23Z91/ 23Z92
Valor Electronics
LT6032, LT6033
Pulse Engineering
PE64502, PE6103
TOKO
Q30ALQ8 1AA3 Q30ALQ9–1AA3
Q30ALQ8–1AA3,
Q30ALQ9 1AA3
Application Notes:
The following procedure is applicable to all three versions
MC68160, MC68160B and MC68160C. References to the
MC68160 includes all the versions.
Resetting the MC68160 after power up.
In some applications, after initial power up, the MC68160
may not be able to transmit or receive data. This is usually
caused by the LOOP and TPFULDL control lines being active
at the same time. This is an illegal condition during normal
operation, it places the MC68160 into the production test
mode.
To exit the test mode and return to normal: Set LOOP low,
TPFULDL high and TPSQEL low. Then, while keeping
TPSQEL low, raise LOOP after 300 ms lower TPFULDL. This
will put the MC68160 into test mode but also resets the
MC68160. After 500 ms lower LOOP to get out of the test
mode. TPFULDL may then be de–asserted if desired.
The MC68160 is now ready for operation.
A hardware implementation of this fix would be to place a
pull down resistor on the TPSQEL pin. Even if test mode is
entered by accident, this ensures that zero’s will be written to
the test register. The hardware implementation will solve the
problem if the test mode is entered because of noise on the
TPSQEL pin. If the controller is toggling the MC68160 lines
while it is booting up, the reset procedure must be followed.
27
0.1 µ F
0.1 µ F
GNDDIG
VDDDIG
LOOP
CS2
CS1
CS0
RX
RENA
3900pF
43
44
45
46
47
48
51 50 49
15
14
C3
20pF
VCC
16 17
X1
20MHz
Motorola MC68360, AMD 7990 & 79C900
Intel 82586, 82590, 82593, 82596
Fujitsu MB86950, MB86960
National 8390, 83C690, 83932B
Standby Low Current Mode
1
1
1
802.3 Communication Controller
0
0
0
0
CS2
C4
20pF
2. Decoupling capacitors should be placed as close to supply pins as possible.
VDD
18 19
1
1
0
0
CS1
41 40
42
R8
330Ω
LED5
MC68160FB, BFB, CFB
Communications Controller Selection
C6
C5
R 12
52
TX
1
0
1
0
CS0
TPAPCE
TPSQEL
TPFULDL
0.039 µ F
300Ω
8
7
6
5
4
3
2
1
9
APORT
VCC
10
VDDDIV
11
VDDFM
12
MFILT
13
GNDFM
VDD
1. For Suitable Crystal (X1) see applications text on previous page.
10 µF
VDD
10 µF
VCC
Power Supply
Bypassing
+5.0V
AMD (7990/79C900)
Intel (825** –86/90/93/96)
Fujitsu (869** –50/60)
National (8390/83C90/83932B)
AutoPort En
CLSN
VDDVCO
GNDVCO
APOR
RCLK
X1
Receive Enable
Receive Data
LoopBack
X2
RENA
RX
LOOP
VDDDIG
MC68360
GNDDIG
Collision Int
Receive Clock
TENA
20
GNDSUB
CLSN
RCLK
TCLK
LED6
R 33
330Ω
TPEN
GNDCTL
21
ACX–
COMMUNICATIONS
CONTROLLER
TPJABB
22
ACX+
TP Enable
Transmit Clock
Transmit Enable
Transmit Data
TPLIL
TPPLR
23
ARX–
24
C2
0.1 µ F
C1
27
28
29
30
31
32
33
34
35
36
37
38
39
R 11
330Ω
LED3
R7
39Ω
R6
39Ω
R5
39Ω
R4
39Ω
R 15
10 KΩ
TPSQEL
TPFULDL
TPAPCE
VDDANA
TPRX–
TPRX+
GNDANA
GNDPWR
VDDPWR
TPTX–
TPTX+
VDDPWR
0.1 µ F
25 26
R9
330Ω
LED4
GNDPWR
TXLED
ATX+
TPEN
TCLK
TENA
TX
CLLED
ATX–
RXLED
ARX+
VDD
VDD
VCC
R 13
330Ω
LED2
R3
100Ω
R2
39Ω
39Ω
R1
R 14
330Ω
LED1
1
7
8
6
4
5
3
2
1
8
7
5
4
3
6
11 14
9
10
12
13
15
16
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
2
Coilcraft (LAX–ET30*)
Pulse Engineering (PE–64***)
Valor (LT600*/LT603*)
TOKO (Q30ALQ*–1AA3)
CTP3
0.01µF
CTP2
0.01µF
11
10
9
13
12
14
16
15
AUI
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
+12V
RJ45
3 RD +
6 RD –
1 TD +
2 TD –
Valor (PT3877, PT3882, FL1012, FL1066)
TOKO (PM01, PM02, PM05)
Pulse Engineering (PE–65433, PE–65434, PE–65424)
Figure 41.
AUI XFMR
28
VDD
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
(Example of PE-65424)
Figure 41. Typical Application Diagram
MC68160 MC68160B MC68160C
MOTOROLA ANALOG IC DEVICE DATA
MC68160 MC68160B MC68160C
OUTLINE DIMENSIONS
FB SUFFIX
PLASTIC PACKAGE
CASE 848D-03
(TQFP–52)
ISSUE C
4X
4X TIPS
0.20 (0.008) H L–M N
–X–
X=L, M, N
0.20 (0.008) T L–M N
52
CL
40
1
AB
39
3X VIEW
AB
Y
–L–
–M–
VIEW Y
B
V
B1
V1
J
13
27
26
ÇÇÇ
ÉÉÉÉ
ÉÉÉÉ
ÇÇÇ
U
0.13 (0.005)
–N–
A1
BASE METAL
F
PLATING
14
G
M
D
T L–M
S
N
S
SECTION AB–AB
S1
ROTATED 90_ CLOCKWISE
A
S
4X
C
θ2
0.10 (0.004) T
–H–
–T–
SEATING
PLANE
4X
θ3
VIEW AA
0.05 (0.002)
S
W
θ1
2XR
R1
0.25 (0.010)
C2
θ
GAGE PLANE
K
C1
E
Z
VIEW AA
MOTOROLA ANALOG IC DEVICE DATA
NOTES:
1 DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982.
2 CONTROLLING DIMENSION: MILLIMETER.
3 DATUM PLANE –H– IS LOCATED AT BOTTOM OF LEAD AND
IS COINCIDENT WITH THE LEAD WHERE THE LEAD EXITS
THE PLASTIC BODY AT THE BOTTOM OF THE PARTING
LINE.
4 DATUMS –L–, –M– AND –N– TO BE DETERMINED AT DATUM
PLANE –H–.
5 DIMENSIONS S AND V TO BE DETERMINED AT SEATING
PLANE –T–.
6 DIMENSIONS A AND B DO NOT INCLUDE MOLD
PROTRUSION. ALLOWABLE PROTRUSION IS 0.25 (0.010)
PER SIDE. DIMENSIONS A AND B DO INCLUDE MOLD
MISMATCH AND ARE DETERMINED AT DATUM PLANE -H-.
7 DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION.
DAMBAR PROTRUSION SHALL NOT CAUSE THE LEAD
WIDTH TO EXCEED 0.46 (0.018). MINIMUM SPACE BETWEEN
PROTRUSION AND ADJACENT LEAD OR PROTRUSION 0.07
(0.003).
DIM
A
A1
B
B1
C
C1
C2
D
E
F
G
J
K
R1
S
S1
U
V
V1
W
Z
θ
θ1
θ2
θ3
MILLIMETERS
MIN
MAX
10.00 BSC
5.00 BSC
10.00 BSC
5.00 BSC
–––
1.70
0.05
0.20
1.30
1.50
0.20
0.40
0.45
0.75
0.22
0.35
0.65 BSC
0.07
0.20
0.50 REF
0.08
0.20
12.00 BSC
6.00 BSC
0.09
0.16
12.00 BSC
6.00 BSC
0.20 REF
1.00 REF
0_
7_
–––
0_
12 _ REF
5_
13 _
INCHES
MIN
MAX
0.394 BSC
0.197 BSC
0.394 BSC
0.197 BSC
–––
0.067
0.002
0.008
0.051
0.059
0.008
0.016
0.018
0.030
0.009
0.014
0.026 BSC
0.003
0.008
0.020 REF
0.003
0.008
0.472 BSC
0.236 BSC
0.004
0.006
0.472 BSC
0.236 BSC
0.008 REF
0.039 REF
0_
7_
–––
0_
12 _ REF
5_
13 _
29
MC68160 MC68160B MC68160C
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola
data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.
Mfax is a trademark of Motorola, Inc.
How to reach us:
USA / EUROPE / Locations Not Listed: Motorola Literature Distribution;
P.O. Box 5405, Denver, Colorado 80217. 303–675–2140 or 1–800–441–2447
JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,
3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 81–3–3521–8315
Mfax: [email protected] – TOUCHTONE 602–244–6609
ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
– US & Canada ONLY 1–800–774–1848 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
INTERNET: http://www.mot.com/SPS/
30
◊
MC68160/D
MOTOROLA ANALOG IC DEVICE DATA