MITSUBISHI INTELLIGENT POWER MODULES PM75CTK060 FLAT-BASE TYPE INSULATED PACKAGE PM75CTK060 ¡600V, 75A Current-sense 6kHz IGBT type inverter ¡Built in IGBT gate drive circuit ¡Built in Faule OC, SC, OT & UV protection Fault output ¡5.5/7.5kW class inverter application APPLICATION Air conditioner, mortor control OUTLINE DRAWING Dimensions in mm (17.52) 109 ±1 96 ±0.5 60.96 ±0.8 7.62 7.62 7.62 1234 5678 9 11 10 12 15–2.54±0.25 2.54 ±0.25 13 15 17 19 14 16 18 C1 21 22 23 24 25 P B N U V W φ1.65 MOUNTING φ4.5 HOLES B 0.6 (t = 0.4) (t = 0.8) A : DETAIL B : DETAIL 41 33 A 5.4 LABEL 6 19. FO 20. P 21. NC 22. N 23. U 24. V 25. W 10 20 (16.75) 12.5 ±0.25 12.5 ±0.25 12.5 ±0.25 12.5 ±0.25 12.5 ±0.25 62.5 ±0.8 21 ±1 13.5 6.35 10. NC 11. WP 12. VWP1 13. VNC 14. VN1 15. NC 16. UN 17. VN 18. WN 9.95 70 ±1 58.5 ±0.5 56.5 ±0.8 (1) 4– R5 1. VUPC 2. NC 3. UP 4. VUP1 5. VVPC 6. NC 7. VP 8. VVP1 9. VWPC 5.4 0.75 A · B: TERMINAL NAME Aug.1999 MITSUBISHI INTELLIGNET POWER MODULES PM75CTK060 FLAT-BASE TYPE INSULATED PACKAGE EQUIVALENT CIRCUIT DIAGRAM FO NC 19 15 VNC WN 13 18 VN1 14 VN 17 WP VWP1 VP VVP1 UP VUP1 VWPC NC VVPC NC VUPC NC 9 11 10 12 5 7 6 8 1 3 2 4 UN 16 Rfo GND In FO VCC GND In FO VCC GND In FO VCC GND In VCC GND In VCC GND In VCC GND Si GND Si GND Si Out GND Si Out GND Si Out TEMP GND Si Out Out Out Th 21 NC 22 N 25 W 24 V 23 U 20 P MAXIMUM RATINGS (Tj = 25°C, unless otherwise noted) INVERTER PART Symbol VCES ±IC ±ICP PC Tj Parameter Collector-emitter voltage Collector current Collector current (peak) Collector dissipation Junction temperature Conditions VD = 15V, ICIN = 10mA TC = 25°C TC = 25°C TC = 25°C Ratings 600 75 150 134 –20 ~ +150 Unit V A A W °C Ratings Unit 20 V 20 mA 20 20 V mA CONTROL PART Symbol Parameter VD Supply voltage ICIN Input current VFO IFO Fault output supply voltage Fault output current Conditions Applied between : VUP1-VUPC , VVP1-VVPC VWP1-VWPC, VN1-VNC Applied between : UP-VUPC, VP-VVPC, WP-VWPC, UN · VN · WN-VNC Applied between : FO -VNC Sink current of FO terminal Aug.1999 MITSUBISHI INTELLIGNET POWER MODULES PM75CTK060 FLAT-BASE TYPE INSULATED PACKAGE TOTAL SYSTEM Symbol Parameter Supply voltage protected VCC(PROT) by OC & SC VCC Supply voltage VCC(surge) Supply voltage (surge) TC Module case operating temperature T stg Storage temperature Viso Isolation voltage Conditions VD = 13.5 ~ 16.5V, Inverter part, Tj = 125°C start Applied between : P-N, operating time Applied between : P-N, surge and non-operating time (Note 1) 60Hz, sinusoidal, AC · 1 min Ratings Unit 400 V 450 500 –20 ~ +100 –40 ~ +125 2500 V V °C °C Vrms Note 1 : T C measuring point is as shown below. TC ELECTRICAL CHARACTERISTICS INVERTER PART Symbol VCE(sat) VEC ton trr tc(on) toff tc(off) ICES (Tj = 25°C, unless otherwise noted) Parameter Test conditions Collector-emitter saturation voltage FWDi forward voltage I C = 75A, Tj = 25°C I C = 75A, Tj = 125°C –IC = 75A, VD = 15V, I CIN = 0mA VD = 15V, ICIN = 10mA Switching time VD = 15V, ICIN = 0mA↔10mA VCC = 300V, IC = 75A Tj = 125°C (Per 1 arm) Inductive Load Collector-emitter cutoff current VCE = VCES, ICIN = 0mA Tj = 25°C Tj = 125°C Min. — — — 0.6 — — — — — — Limits Typ. 1.8 1.85 2.2 1.2 0.15 0.5 2.8 0.6 — — Max. 2.7 2.78 3.3 2.4 0.3 1.1 3.6 1.2 1 10 Min. — — 1 1 115 — — 100 — 11.5 — — — Limits Typ. 40 13 3 3 161 241 10 110 90 12.0 12.5 — 10 Max. 55 18 5 5 — — — 120 — 12.5 — 0.01 15 1.0 1.8 Unit V V µs µs µs µs µs mA CONTROL PART Symbol Parameter Test conditions Circuit current Ith(ON) Ith(OFF) OC SC toff(OC) OT OTr UV UVr IFO(H) IFO(L) Input on threshold current Input off threshold current Over current trip level Short circuit trip level Over current delay time tFO Note 2 : Fault Fault Fault Fault Over temperature protection Supply circuit under voltage protection Fault output current (Note 2) VD = 15V, VFO = 15V Minimum fault output pulse width (Note 2) output output output output VN1 -VNC VXP1-VXPC Applied between : UP-VUPC, VP -VVPC, WP-VWPC UN · V N · WN -VNC –20°C ≤ T j ≤ 125°C, VD = 15V –20°C ≤ T j ≤ 125°C, VD = 15V VD = 15V Base-plate Trip level Temperature detection, VD = 15V Reset level Trip level –20°C ≤ T j ≤ 125°C Reset level VD = 15V, ICIN = 0mA ID VD = 15V — Unit mA mA mA A A µs °C °C V V mA mA ms is given only when the internal OC, SC, OT & UV protection. of OC, SC protection operate by lower arm. of OC, SC protection given pulse. of OT, UV protection given pulse while over level. (OT is only N side) Aug.1999 MITSUBISHI INTELLIGNET POWER MODULES PM75CTK060 FLAT-BASE TYPE INSULATED PACKAGE THERMAL RESISTANCES Parameter Symbol Rth(j-c)Q Rth(j-c)F Rth(c-f) Junction to case thermal resistances Contact thermal resistance Test conditions Inverter IGBT part, per 1/6 module Inverter FWDi part, per 1/6 module Case to fin, thermal grease applied, per 1 module Min. — — — Limits Tye. — — — Max. 0.93 0.91 0.036 °C / W °C / W °C / W Min. 0.98 10 — Limits Tye. 1.18 12 150 Max. 1.47 15 — N·m kg·cm g Unit MECHANICAL RATINGS AND CHARACTERISTICS Symbol Parameter — Mounting torque — Weight Test conditions Mounting screw : M4 Unit RECOMMENDED CONDITIONS FOR USE Symbol VCC Parameter Supply voltage VD ICIN(ON) ICIN(OFF) fPWM tdead Input on current Input off current PWM input frequency Arm shoot-through blocking time Test conditions Applied between : P-N Applied between : VUP1-VUPC, VVP1-VVPC VWP1-VWPC, VN1-V NC Ratings (Note 3) Applied between : UP, VP, WP, UN, VN, WN Using application circuit Opto-coupler’s input signal Using application circuit Opto-coupler’s input signal ≤ 400 Unit V 15 ± 1.5 V ≥5 ≤1 ≤8 ≥3 mA mA kHz µs Note 3 : Permissible ripple value : dv/dt ≤ ±5V/µs, Vripple ≤ 2V P-P Aug.1999 MITSUBISHI INTELLIGNET POWER MODULES PM75CTK060 FLAT-BASE TYPE INSULATED PACKAGE PERFORMANCE CURVES COLLECTOR-EMITTER SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) VD = 17V IC (A) 13V 60 40 20 0 1 2 3 3 2 1 0 5 4 VD = 15V VCIN = 0V Tj = 25°C 4 Tj = 125°C 0 20 40 60 80 100 120 140 160 COLLECTOR-EMITTER VOLTAGE VCE (V) COLLECTOR CURRENT IC (A) COLLECTOR-EMITTER SATURATION VOLTAGE VS. SUPPLY VOLTAGE (TYPICAL) SWITCHING TIME VS. COLLECTOR CURRENT (TYPICAL) 101 5 SWITCHING TIMES (µs) IC = 75A VCIN = 0V Tj = 25°C 4 Tj = 125°C 3 2 1 7 5 4 3 Tj = 125°C VCC = 300V VD = 15V INDUCTIVE LOAD 2 toff 100 ton 7 5 4 3 tc(off) tc(on) 2 0 COLLECTOR REVERSE CURRENT 15V 5 12 102 16 14 18 10–1 20 3 4 5 7 102 2 3 4 5 7 COLLECTOR CURRENT IC (A) FREE-WHEEL DIODE FORWARD CHARACTERISTICS (TYPICAL) REVERSE RECOVERY CHARACTERISTICS OF FREE-WHEEL DIODE (TYPICAL) 100 102 VD = 15V 2 101 7 5 4 3 2 0 2 SUPPLY VOLTAGE VD (V) 7 VCIN = 15V 5 Tj = 25°C 4 Tj = 125°C 3 100 7 101 0.5 1 1.5 2 2.5 EMITTER-COLLECTOR VOLTAGE VEC (V) 7 5 4 3 7 5 4 3 lrr 2 2 trr 10–1 101 7 5 4 3 7 5 4 3 Tj = 125°C VCC = 300V 2 VD = 15V INDUCTIVE LOAD 10–2 7 101 2 3 4 5 7 102 2 100 2 3 4 5 7 COLLECTOR REVERSE CURRENT REVERSE RECOVERY CURRENT Irr (A) 80 0 COLLECTOR-EMITTER SATURATION VOLTAGE VCE (sat) (V) Tj = 25°C VCIN = 0V REVERSE RECOVERY TIME trr (µs) COLLECTOR CURRENT IC (A) 100 COLLECTOR-EMITTER SATURATION VOLTAGE VCE (sat) (V) OUTPUT CHARACTERISTICS (TYPICAL) IC (A) Aug.1999 MITSUBISHI INTELLIGNET POWER MODULES PM75CTK060 FLAT-BASE TYPE INSULATED PACKAGE TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (IGBT per 1 element) TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (FWDi per 1 element) 7 Single Pulse 5 3 Rth(j – c)Q = 0.93°C/ W 2 100 7 5 3 2 10–1 7 5 3 2 10–2 7 5 3 2 10–3 10–3 2 3 5 710–2 2 3 5 710–1 2 3 5 7100 2 3 5 7101 TIME (s) 101 NORMALIZED TRANSIENT THERMAL IMPEDANCE Zth (j – c) NORMALIZED TRANSIENT THERMAL IMPEDANCE Zth (j – c) 101 7 Single Pulse 5 3 Rth(j – c)F = 0.91°C/ W 2 100 7 5 3 2 10–1 7 5 3 2 10–2 7 5 3 2 10–3 10–3 2 3 5 710–2 2 3 5 710–1 2 3 5 7100 2 3 5 7101 TIME (s) Aug.1999