MITSUBISHI MITSUBISHI <INTELLIGENT <INTELLIGENT POWER POWER MODULES> MODULES> PM100CSE120 PM100CSE120 FLAT-BASE FLAT-BASE TYPE TYPE INSULATED INSULATED PACKAGE PACKAGE PM100CSE120 FEATURE a) Adopting new 4th generation planar IGBT chip, which performance is improved by 1µm fine rule process. b) Using new Diode which is designed to get soft reverse recovery characteristics. • 3φ 100A, 1200V Current-sense IGBT for 15kHz switching • Monolithic gate drive & protection logic • Detection, protection & status indication circuits for overcurrent, short-circuit, over-temperature & under-voltage • Acoustic noise-less 18.5/22kW class inverter application • UL Recognized Yellow Card No.E80276(N) File No.E80271 APPLICATION General purpose inverter, servo drives and other motor controls PACKAGE OUTLINES Dimensions in mm 135 ±1 120.5 ±0.5 10.16 789 10.16 11 13 15 10 12 14 16 Terminal code B PPS VUPC UP VUP1 VVPC VP VVP1 VWPC WP VWP1 VNC φ2.54 V W 3.22 0.64 Screwing depth Min9.0 2-2.54 0.64 10.6 16- 4-R6 6-M5 NUTS 11.6 2-φ2.54 26 33.7 34.7 A 26 21.3 51.5 +1.0 VN1 NC UN VN WN FO 10.5 U 24.1 –0.5 4 11. 12. 13. 14. 15. 16. 5 N 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 10.16 2-2.54 2-2.54 2-2.54 6-2.54 67.4 74.4 13 20 P 20 3.22 456 24.1 11 16.5 1 23 39.5 4- φ5.5 MOUNTING HOLES LABEL 95.5 ±0.5 110 ±1 39.7 0.5 ±0.3 A : DETAIL Jul. 2005 MITSUBISHI <INTELLIGENT POWER MODULES> PM100CSE120 FLAT-BASE TYPE INSULATED PACKAGE INTERNAL FUNCTIONS BLOCK DIAGRAM Rfo=1.5kΩ WP NC Fo VNC W N VN1 VN UN VWP1 VWPC VP VVP1 VVPC UP VUP1 VUPC Rfo Gnd In Gnd Fo Vcc Gnd In Si Out Gnd Fo Vcc TEMP Si Out Gnd In Gnd Fo Vcc Si Out Gnd In Gnd Vcc Si Out Gnd In Gnd Vcc Gnd In Si Out Gnd Vcc Si Out Th NC N W V U P MAXIMUM RATINGS (Tj = 25°C, unless otherwise noted) INVERTER PART Symbol VCES ±IC ±ICP PC Tj Parameter Collector-Emitter Voltage Collector Current Collector Current (Peak) Collector Dissipation Junction Temperature Condition VD = 15V, VCIN = 15V TC = 25°C TC = 25°C TC = 25°C Ratings 1200 100 200 595 –20 ~ +150 Unit V A A W °C Ratings Unit 20 V 20 V 20 20 V mA CONTROL PART Symbol Parameter VD Supply Voltage VCIN Input Voltage VFO IFO Fault Output Supply Voltage Fault Output Current Condition Applied between : VUP1-VUPC VVP1-VVPC, VWP1-VWPC, VN1-VNC Applied between : UP-VUPC, VP-VVPC WP-VWPC, UN • VN • WN-VNC Applied between : FO-VNC Sink current at FO terminal Jul. 2005 MITSUBISHI <INTELLIGENT POWER MODULES> PM100CSE120 FLAT-BASE TYPE INSULATED PACKAGE TOTAL SYSTEM Parameter Supply Voltage Protected by VCC(PROT) OC & SC VCC(surge) Supply Voltage (Surge) Module Case Operating TC Temperature Storage Temperature Tstg Isolation Voltage Viso Ratings Condition VD = 13.5 ~ 16.5V, Inverter Part, Tj = 125°C Start Symbol Unit 800 V 1000 V (Note-1) –20 ~ +100 °C 60Hz, Sinusoidal, Charged part to Base, AC 1 min. –40 ~ +125 2500 °C Vrms Applied between : P-N, Surge value or without switching (Note-1) TC measurement point is as shown below. (Base plate depth 3mm) P Tc N B 63mm U V W THERMAL RESISTANCES Symbol Rth(j-c)Q Rth(j-c)F Rth(j-c’)Q Rth(j-c’)F Rth(c-f) Parameter Junction to case Thermal Resistances Contact Thermal Resistance Test Condition Inverter IGBT part (per 1 element), (Note-1) Inverter FWDi part (per 1 element), (Note-1) Inverter IGBT part (per 1 element), (Note-2) Inverter FWDi part (per 1 element), (Note-2) Case to fin, Thermal grease applied (per 1 module) Min. — — — — — Limits Typ. — — — — — Max. 0.21 0.35 0.13 0.21 0.018 Min. — — — 0.5 — — — — — — Limits Typ. 2.4 2.1 2.5 1.0 0.15 0.4 2.5 0.7 — — Max. 3.2 2.8 3.5 2.5 0.3 1.0 3.5 1.2 1 10 Unit °C/W (Note-2) TC measurement point is just under the chips. If you use this value, Rth(f-a) should be measured just under the chips. ELECTRICAL CHARACTERISTICS (Tj = 25°C, unless otherwise noted) INVERTER PART Symbol VCE(sat) VEC ton trr tc(on) toff tc(off) ICES Parameter Test Condition Collector-Emitter Saturation Voltage FWDi Forward Voltage VD = 15V, IC = 100A VCIN = 0V, Pulsed (Fig. 1) –IC = 100A, VD = 15V, VCIN = 15V Switching Time VD = 15V, VCIN = 15V↔0V VCC = 600V, IC = 100A Tj = 125°C Inductive Load (upper and lower arm) Collector-Emitter Cutoff Current VCE = VCES, VCIN = 15V (Fig. 4) Tj = 25°C Tj = 125°C (Fig. 2) (Fig. 3) Tj = 25°C Tj = 125°C Unit V V µs mA Jul. 2005 MITSUBISHI <INTELLIGENT POWER MODULES> PM100CSE120 FLAT-BASE TYPE INSULATED PACKAGE CONTROL PART Symbol Parameter Test Condition ID Circuit Current Vth(on) Vth(off) Input ON Threshold Voltage Input OFF Threshold Voltage VN1-VNC VXP1-VXPC Applied between : UP-VUPC, VP-VVPC, WP-VWPC UN • VN • WN-VNC OC Over Current Trip Level VD = 15V SC toff(OC) OT OTr UV UVr IFO(H) IFO(L) Short Circuit Trip Level Over Current Delay Time –20≤ Tj ≤ 125°C, VD = 15V VD = 15V Base-plate Temperature detection, VD = 15V tFO Over Temperature Protection VD = 15V, VCIN = 15V (Fig. 5,6) Tj = 25°C Tj = 125°C (Fig. 5,6) (Fig. 5,6) Trip level Reset level Trip level Reset level Supply Circuit Under-Voltage Protection –20 ≤ Tj ≤ 125°C Fault Output Current VD = 15V, VFO = 15V (Note-3) Minimum Fault Output Pulse Width VD = 15V (Note-3) (Note-3) Fault Fault Fault Fault output output output output Min. — — 1.2 1.7 228 145 — — 111 — 11.5 — — — Limits Typ. 45 15 1.5 2.0 345 — 340 10 118 100 12.0 12.5 — Max. 62 20 1.8 2.3 — — — — 125 — 12.5 — Unit mA V A A µs °C V 10 0.01 15 mA 1.0 1.8 — ms Min. 2.5 2.5 — Limits Typ. 3.0 3.0 920 is given only when the internal OC, SC, OT & UV protection. of OT protection operate by lower arm. of OC, SC protection given pulse. of OT, UV protection given pulse while over level. MECHANICAL RATINGS AND CHARACTERISTICS Symbol — — — Test Condition Parameter Mounting torque Mounting torque Weight Main terminal Mounting part screw : M5 screw : M5 — Max. 3.5 3.5 — Unit N•m N•m g RECOMMENDED CONDITIONS FOR USE Symbol VCC Parameter Supply Voltage VD Control Supply Voltage VCIN(on) VCIN(off) Input ON Voltage Input OFF Voltage fPWM PWM Input Frequency tdead Arm Shoot-through Blocking Time Test Condition Applied across P-N terminals Applied between : VUP1-VUPC, VVP1-VVPC VWP1-VWPC, VN1-VNC (Note-4) Applied between : UP-VUPC, VP-VVPC, WP-VWPC UN • VN • WN-VNC Using Application Circuit input signal of IPM, 3φ sinusoidal PWM VVVF inverter (Fig. 8) For IPM’s each input signals (Fig. 7) Recommended value ≤ 800 Unit V 15 ± 1.5 V ≤ 0.8 ≥ 4.0 V ≤ 20 kHz ≥ 3.0 µs (Note-4) Allowable Ripple rating of Control Voltage : dv/dt ≤ ±5V/µs, 2Vp-p Jul. 2005 MITSUBISHI <INTELLIGENT POWER MODULES> PM100CSE120 FLAT-BASE TYPE INSULATED PACKAGE PRECAUTIONS FOR TESTING 1. Before appling any control supply voltage (VD), the input terminals should be pulled up by resistores, etc. to their corresponding supply voltage and each input signal should be kept off state. After this, the specified ON and OFF level setting for each input signal should be done. 2. When performing “OC” and “SC” tests, the turn-off surge voltage spike at the corresponding protection operation should not be allowed to rise above VCES rating of the device. (These test should not be done by using a curve tracer or its equivalent.) P, (U,V,W) IN (Fo) VCIN P, (U,V,W) Ic V IN (Fo) VCIN –Ic V (15V) (0V) VD (all) U,V,W, (N) VD (all) Fig. 1 VCE(sat) Test U,V,W, (N) Fig. 2 VEC Test a) Lower Arm Switching P VCIN (15V) trr Signal input (Upper Arm) CS VCIN Signal input (Lower Arm) VCE Irr U,V,W Ic Vcc Fo 90% 90% N b) Upper Arm Switching VD (all) Ic 10% 10% 10% 10% P VCIN U,V,W CS VCIN (15V) Signal input (Lower Arm) tc (on) VCIN Signal input (Upper Arm) Vcc td (on) tr tc (off) td (off) tf Fo (ton= td (on) + tr) (toff= td (off) + tf) N Ic VD (all) Fig. 3 Switching time Test circuit and waveform P, (U,V,W) A VCIN (15V) VCIN IN (Fo) Pulse VCE VD (all) Over Current U,V,W, (N) OC IC toff (OC) Fig. 4 ICES Test P, (U,V,W) Constant Current Short Circuit Current IN (Fo) VCC Constant Current VCIN SC IC VD (all) U,V,W, (N) IC Fig. 5 OC and SC Test Fig. 6 OC and SC Test waveform P VD VCINP U,V,W Vcc VD VCINN N Ic VCINP 0V t VCINN 0V t tdead tdead tdead Fig. 7 Dead time measurement point example Jul. 2005 MITSUBISHI <INTELLIGENT POWER MODULES> PM100CSE120 FLAT-BASE TYPE INSULATED PACKAGE P ≥10µ 20k VUP1 Vcc → VD IF OUT + – Si UP In VUPC U GND GND ≥0.1µ VVP1 VD Vcc Si VP In VVPC V GND GND VWP1 VD OUT Vcc M OUT Si WP In VWPC W GND GND 20k → Vcc ≥10µ IF Fo UN OUT Si In GND GND ≥0.1µ N TEMP 20k → Vcc ≥10µ IF Fo VN Th OUT Si In GND GND ≥0.1µ 20k → VD VN1 Vcc ≥10µ IF Fo WN ≥0.1µ In OUT Si GND GND VNC NC NC 5V 1k Fo Rfo : Interface which is the same as the U-phase Fig. 8 Application Example Circuit NOTES FOR STABLE AND SAFE OPERATION ; Design the PCB pattern to minimize wiring length between opto-coupler and IPM’s input terminal, and also to minimize the stray capacity between the input and output wirings of opto-coupler. Quick opto-couplers : TPLH, TPLH ≤ 0.8µs. Use High CMR type. The line between opto-coupler and intelligent module should be shortened as much as possible to minimize the floating capacitance. Slow switching opto-coupler : recommend to use at CTR = 100 ~ 200%, Input current = 8 ~ 10mA, to work in active. Use 4 isolated control power supplies (VD). Also, care should be taken to minimize the instantaneous voltage charge of the power supply. Make inductance of DC bus line as small as possible, and minimize surge voltage using snubber capacitor between P and N terminal. Use line noise filter capacitor (ex. 4.7nF) between each input AC line and ground to reject common-mode noise from AC line and improve noise immunity of the system. • • • • • • Jul. 2005 MITSUBISHI <INTELLIGENT POWER MODULES> PM100CSE120 FLAT-BASE TYPE INSULATED PACKAGE PERFORMANCE CURVES COLLECTOR-EMITTER SATURATION VOLTAGE (VS. Ic) CHARACTERISTICS (TYPICAL) OUTPUT CHARACTERISTICS (TYPICAL) COLLECTOR-EMITTER SATURATION VOLTAGE VCE (sat) (V) 120 100 15V 80 13V 60 40 20 0 0 0.5 1 1.5 2 2.5 3 VD = 15V 2 1.5 1 0.5 Tj = 25°C Tj = 125°C 0 0 20 40 60 80 100 120 COLLECTOR CURRENT IC (A) COLLECTOR-EMITTER SATURATION VOLTAGE (VS. VD) CHARACTERISTICS (TYPICAL) 3 SWITCHING TIME CHARACTERISTICS (TYPICAL) 2.5 2 1.5 1 IC = 100A Tj = 25°C Tj = 125°C 0.5 0 12 13 14 15 16 17 101 VCC = 600V VD = 15V Tj = 25°C Tj = 125°C 2 Inductive load 7 5 4 3 100 tc(off) tc(on) tc(on) tc(off) 7 5 4 3 2 10–1 1 10 18 2 3 4 5 7 102 2 3 4 5 7 103 CONTROL SUPPLY VOLTAGE VD (V) COLLECTOR CURRENT IC (A) SWITCHING TIME CHARACTERISTICS (TYPICAL) SWITCHING LOSS CHARACTERISTICS (TYPICAL) 101 SWITCHING TIME ton, toff (µs) 2.5 COLLECTOR-EMITTER VOLTAGE VCE (V) SWITCHING TIME tc(on), tc(off) (µs) COLLECTOR-EMITTER SATURATION VOLTAGE VCE (sat) (V) VD = 17V 7 5 4 3 2 toff ton 100 7 5 4 3 VCC = 600V VD = 15V Tj = 25°C Tj = 125°C Inductive load 2 10–1 1 10 2 3 4 5 7 102 2 3 4 5 7 103 COLLECTOR CURRENT IC (A) SWITCHING LOSS ESW(on), ESW(off) (mJ/pulse) COLLECTOR CURRENT IC (A) Tj = 25°C 102 7 5 4 3 2 ESW(on) 101 ESW(off) ESW(off) 7 5 4 3 2 ESW(on) 100 VCC = 600V VD = 15V Tj = 25°C Tj = 125°C Inductive load 7 5 4 3 2 10–1 1 10 2 3 4 5 7 102 2 3 4 5 7 103 COLLECTOR CURRENT IC (A) Jul. 2005 MITSUBISHI <INTELLIGENT POWER MODULES> PM100CSE120 102 VD = 15V 7 5 4 3 2 101 7 5 4 3 2 100 Tj = 25°C Tj = 125°C 0 0.5 1 1.5 2 2.5 5 4 3 5 4 3 2 2 trr 10–1 7 5 4 3 101 VCC = 600V VD = 15V Tj = 25°C Tj = 125°C Inductive load 2 10–2 1 10 3 2 3 4 5 7 102 2 7 5 4 3 2 100 3 4 5 7 103 EMITTER-COLLECTOR VOLTAGE VEC (V) COLLECTOR RECOVERY CURRENT –IC (A) ID VS. fc CHARACTERISTICS (TYPICAL) TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (IGBT PART) 101 VD = 15V Tj = 25°C N-side 80 60 40 P-side 20 0 0 5 10 15 20 25 CARRIER FREQUENCY fc (kHz) NORMALIZED TRANSIENT THERMAL IMPEDANCE Zth (j – c) 100 CIRCUIT CURRENT ID (mA) DIODE REVERSE RECOVERY CHARACTERISTICS (TYPICAL) 100 102 7 7 Irr REVERSE RECOVERY CURRENT lrr (A) DIODE FORWARD CHARACTERISTICS (TYPICAL) REVERSE RECOVERY TIME trr (µs) COLLECTOR RECOVERY CURRENT –IC (A) FLAT-BASE TYPE INSULATED PACKAGE 7 5 3 2 100 7 5 3 2 10–1 7 5 3 2 10–2 7 5 3 Single Pulse 2 Per unit base = Rth(j – c)Q = 0.21°C/W 10–3 10–3 2 3 5 710–2 2 3 5 710–1 2 3 5 7100 2 3 5 7101 TIME (s) TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (FWDi PART) NORMALIZED TRANSIENT THERMAL IMPEDANCE Zth (j – c) 101 7 5 3 2 100 7 5 3 2 10–1 7 5 3 2 10–2 7 5 3 Single Pulse 2 Per unit base = Rth(j – c)F = 0.35°C/W 10–3 10–3 2 3 5 710–2 2 3 5 710–1 2 3 5 7100 2 3 5 7101 TIME (s) Jul. 2005