MOTOROLA MC13145FTA

Order this document by MC13145/D
UHF WIDEBAND
RECEIVER SUBSYSTEM
(LNA, Mixer, VCO, Prescalar,
IF Subsystem,
Coilless Detector)
The MC13145 is a dual conversion integrated RF receiver intended for
ISM band applications. It features a Low Noise Amplifier (LNA), two 50 linear Mixers with linearity control, Voltage Controlled Oscillator (VCO),
second LO amplifier, divide by 64/65 dual modulus Prescalar, split IF
Amplifier and Limiter, RSSI output, Coilless FM/FSK Demodulator and
power down control. Together with the transmit chip (MC13146) and the
baseband chip (MC33410), a complete 900 MHz cordless phone system can
be implemented. This device may be used in applications within 2.0 GHz
since its RF bandwidth is greater than 2.4 GHz.
• Low (<1.8 dB @ 900 MHz) Noise Figure LNA with 14 dB Gain
•
•
•
•
•
•
•
•
Externally Programmable Mixer linearity: IIP3 = 10(nom.) to +20 dBm
(Mixer1); IIP3 = 10 (nom.) to 20 dBm (Mixer2)
50 Mixer Input Impedance and Open Collector Output (Mixer 1 and
Mixer 2); 50 Second LO (LO2) Input Impedance
Low Power 64/65 Dual Modulus Prescalar (MC12053 type)
1
48
FTA SUFFIX
PLASTIC PACKAGE
CASE 932
(LQFP–48)
Split IF for Improved Filtering and Extended RSSI Range
Internal 330 Terminations for 10.7 MHz Filters
ORDERING INFORMATION
Linear Coilless FM/FSK Demodulator with Externally Programmable
Bandwidth, Center Frequency and Audio level
2.7 V to 6.5 V Operation, Low Current Drain (< 30 mA @ 3.0 V) with
Power Down Mode (<1.0 A)
2.4 GHz RF, 1.0 GHz IF1 and 50 MHz IF2 Bandwidth
Device
Temperature Range
Package
XC13145FTA
–40° to +85°C
LQFP– 48
ESD Sensitive — Handle with Care
VCC
VCC
MC
PRSC Out
VEE
RSSI
Det Out
Det Gain
AFT
AFT Buf
Fadj
VEE
PIN CONNECTIONS AND FUNCTIONAL BLOCK DIAGRAM
12
11
10
9
8
7
6
5
4
3
2
1
VEE 13
48 VEE
Demod
47 BWadj
LNA In 14
VEE 15
RF
/64, 65
VEE 16
46 Lim Dec2
LNA
Lim
45 Lim Dec1
44 Lim In
LNA Out 17
43 VCC
Mxr1In 19
42 VCC
Lin Adj1 20
41 IF Out
Control
VEE 18
Enable 21
27
28
29
30
31
32
33
34
V EE
LO2
V EE
35
36
IF2–
26
IF2+
25
VCC
37 VEE
Mxr2 In
oscB 24
LinAdj2
38 IF In
IF1–
oscE 23
IF1+
39 IF Dec1
V EE
oscC 22
VCC
LO
40 IF Dec2
IF
IF2
IF1
This document contains information on a product under development. Motorola
reserves the right to change or discontinue this product without notice.
MOTOROLA RF/IF DEVICE DATA
 Motorola, Inc. 1998
Rev 0
1
MC13145
OVERALL RECEIVER SPECIFICATIONS
MAXIMUM RATINGS
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
m
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
Rating
Symbol
Value
Unit
Power Supply Voltage
VCC(max)
7.0
Vdc
Junction Temperature
TJ(max)
150
°C
Tstg
– 65 to +150
°C
Symbol
Value
Unit
VCC
VEE
2.7 to 6.5
Vdc
Input Frequency
fin
100 to 2000
MHz
Ambient Temperature Range
TA
– 40 to +85
°C
Maximum Input Signal Level:
Pin
Storage Temperature Range
RECOMMENDED OPERATING CONDITIONS
Rating
Power Supply Voltage (TA = 25°C)
0
– with no damage
– with minor performance degradation
dBm
5.0
–10
RECEIVER DC ELECTRICAL CHARACTERISTICS (TA = 25°C; VCC = 3.0 Vdc; No Input Signal,
unless otherwise noted)
Characteristics
Symbol
Typical
Unit
Total Supply Current (Enable = VCC)
Itotal
30
mA
Power Down Current (Enable = VEE)
Itotal
<1.0
A
RECEIVER AC ELECTRICAL CHARACTERISTICS (TA = 25°C; VCC = 3.0 Vdc; Fmod = 1.0 kHz; Fdev = ± 25 kHz;
IF filter bandwidth = 150 kHz, unless otherwise noted)
Typical
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
W
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
900
1900
Unit
MHz
12 dB SINAD Sensitivity (with C–message filter at DetOut)
–115
TBD
dBm
30 dB SINAD Sensitivity (No IF filter distortion within ±40 kHz)
–100
TBD
dBm
SINAD Variation with IF Offset of ±40 kHz (No IF filter distortion within ±40 kHz)
5.0
TBD
dB
RSSI Dynamic Range
80
TBD
dB
Characteristics
Symbol
Input 1.0 dB Compression Point(Measured at IF output)
Pin–1dB
–18
TBD
dBm
Input 3rd Order Intercept Point (Measured at IF output)
IIP3
–8.0
TBD
dBm
Demodulator Output Swing (5.0 k Load)
0.5
0.5
Vpp
Demodulator Bandwidth (±1.0 dB bandwidth)
100
100
kHz
Prescalar Output Level (10 k //8.0 pF load)
0.5
0.5
Vpp
Modulus Control Input Level
0.5
0.5
Vpp
SNR @ –30 dBm Signal Input (<25 kHz deviation;with C–Message Filter)
50
TBD
dB
Total Harmonic Distortion (<25 kHz deviation;with C–Message Filter)
1.0
TBD
%
Spurious Response SINAD (RF In: –50 dBm)
12
TBD
dB
2
MOTOROLA RF/IF DEVICE DATA
MC13145
INDIVIDUAL BLOCK SPECIFICATIONS
LOW NOISE AMPLIFIER ELECTRICAL CHARACTERISTICS (TA = 25°C; VCC = 3.0 Vdc, unless otherwise noted)
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
W
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
W
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
Typical
Symbol
900
1900
Unit
MHz
Amplifier Gain
S21
14
TBD
dB
Noise Figure
NF
1.8
TBD
dB
Pin–1dB
–8.0
TBD
dBm
3rd Order Intercept Point
IIP3
–5.0
TBD
dBm
Reverse Isolation
S12
–35
TBD
dB
Input Impedance (with externals)
50
50
Output Impedance (with externals)
50
50
Characteristics
1.0 dB Gain Compression Point
Input Match (with externals)
S11
15
TBD
dB
Output Match (with externals)
S22
15
TBD
dB
–45
TBD
dBm
LO1 to LNA Input Leakage
FIRST MIXER ELECTRICAL CHARACTERISTICS (TA = 25°C; VCC = 3.0 Vdc, unless otherwise noted)
Typical
900
1900
Unit
MHz
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
W
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
W
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
W
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
W
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
Characteristics
Symbol
Power Conversion Gain (Pin = –30 dBm)
Pgc
0
TBD
dB
Noise Figure
NF
13
TBD
dB
Pin–1dB
–1.0
TBD
dBm
IIP3
9.0
TBD
dBm
Input Impedance (single–ended)
50
50
Output Impedance (differential with externals)
50
50
Input Match
20
TBD
dB
Output Match (with externals)
20
TBD
dB
RF to IF1 Leakage
–38
TBD
dB
LO to IF1 Leakage
–33
TBD
dBm
LO to RF Leakage
–33
TBD
dBm
Mixer Out to IF in Leakage
–80
TBD
dB
1.0 dB Gain Compression Point
3rd Order Intercept Point
SECOND MIXER ELECTRICAL CHARACTERISTICS (TA = 25°C; VCC = 3.0 Vdc, unless otherwise noted)
Characteristics
Noise Figure
1.0 dB Gain Compression Point
3rd Order Intercept Point
Symbol
Typical
Unit
NF
13
dB
Pin–1dB
–1.0
dBm
IIP3
9.0
dBm
Input Impedance (single–ended)
50
Output Impedance (differential with externals)
330
Input Match
20
dB
Output Match (with externals)
20
dB
MOTOROLA RF/IF DEVICE DATA
3
MC13145
INDIVIDUAL BLOCK SPECIFICATIONS (continued)
LOCAL OSCILLATOR ELECTRICAL CHARACTERISTICS (TA = 25°C; VCC = 3.0 Vdc, unless otherwise noted)
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
Typical
900
1900
Unit
MHz
LO Emitter Current (Enable = high)
2.0
TBD
mA
Phase Noise @ 10 kHz Offset
–80
–75
dBc/Hz
Modulation Sideband
–40
TBD
dBc
Characteristics
Symbol
PRESCALAR ELECTRICAL CHARACTERISTICS (TA = 25°C; VCC = 3.0 Vdc, unless otherwise noted)
Typical
Unit
MHz
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
Á
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
W
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
W
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
m
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
900
1900
65
64
65
64
Output Impedance
50
50
Prescalar Output Level (10 k //8pF load)
0.5
0.5
Vpp
Characteristics
Symbol
Divide Ratio
– MC = low
– MC = high
MC Input Level
0.5
0.5
Vpp
MC Current Input (optional)
200
200
App
Prescalar Out to IF Amp and Lim Amp Input Leakage
–85
TBD
dBm
IF AND LIMITING AMPLIFIERS ELECTRICAL CHARACTERISTICS (TA = 25°C; VCC = 3.0 Vdc,
unless otherwise noted)
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
W
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
W
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
m
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
m
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
m
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
Characteristics
Symbol
Typical
Unit
IF and Lim Amplifier Bandwidth
40
MHz
IF Amplifier Gain
40
dB
IF Amplifier Noise Figure
7.0
dB
IF Input & Output Impedance
330
IF Amp Input & Output Match
20
dB
Limiting Amplifier Gain
85
dB
Lim Amp Input Impedance
330
Lim Amp Input Match
15
dB
IF Amp Output to Lim Amp Input Leakage (at 10.7 MHz)
80
dB
RSSI Dynamic Range
80
dB
RSSI Slope
0.5
A/dB
RSSI Current Range
0 to 40
A
RSSI Response Time
1.0
s
COILLESS DEMODULATOR ELECTRICAL CHARACTERISTICS (TA = 25°C; VCC = 3.0 Vdc,
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
W
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁ
unless otherwise noted)
Characteristics
Symbol
Typical
Unit
DetOut
0.5
Vpp
Center Frequency
10.7
MHz
Frequency Adjust
< 20
MHz
Bandwidth Adjust
100 to 600
kHz
Output Impedance
2000
Settling Time (assert Enable pin)
TBD
Demodulator Output (at 25 kHz deviation)
4
ms
MOTOROLA RF/IF DEVICE DATA
MC13145
Figure 1. Application Diagram
MC
PRSC Out
10 n
1.0 n
RSSI
50 k
220 n
56 p
24 k
Det Out
330 n 68 k
5
4
3
14
6.8 n
15
64/65
LNA
1
48
BWadj
50 k
47
1.0 n
46
S
16
1.0 n
Det Out
13
2
Fadj
6
AFT Out
7
AFT
8
Det Gain
9
VCC VCC
6.8 n
47 p
10
RSSI
LNAin
11
PRSC Out
12
1.0 n
MC
2.7 k
100 n
Lim
45
1.0 n
390
44
17
18
18
19
20
10 k
21
47 p
MC13145
43
VCC
42
1.0 n
100 n
IF
39
3.0 p
1.0 n
38
3.0 p
47 p
24
D1*
VCC
25
9.1 p
37
VCC
26
27
28
29 30
10 n
1.0 µ
31
32
33
34
35
10 n
10M7
23
2.55 n
10 n
40
22
100 nH
1.0 µ
41
Control
47 p
VCC
10M7
100 p
36
1.0 µ
9.0 p
150 p
33 k
16 p
39 p
12 n
VCont
2.7 µH
10 n
VCC
2.7 µH
T1**
18
510
1.0 µ
100 n
1.0 n
10 n
1.0 µ
10 n
LD2 In
* D1 = MMBV809L
**T1 = Toko Part # 600ENAS–A998EK
MOTOROLA RF/IF DEVICE DATA
5
MC13145
OUTLINE DIMENSIONS
FTA SUFFIX
PLASTIC PACKAGE
CASE 932–02
(LQFP)
ISSUE D
4X
0.200 (0.008) AB T–U Z
9
DETAIL Y
A
A1
48
NOTES:
1 DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2 CONTROLLING DIMENSION: MILLIMETER.
3 DATUM PLANE –AB– IS LOCATED AT BOTTOM OF
LEAD AND IS COINCIDENT WITH THE LEAD
WHERE THE LEAD EXITS THE PLASTIC BODY AT
THE BOTTOM OF THE PARTING LINE.
4 DATUMS –T–, –U–, AND –Z– TO BE DETERMINED
AT DATUM PLANE –AB–.
5 DIMENSIONS S AND V TO BE DETERMINED AT
SEATING PLANE –AC–.
6 DIMENSIONS A AND B DO NOT INCLUDE MOLD
PROTRUSION. ALLOWABLE PROTRUSION IS
0.250 (0.010) PER SIDE. DIMENSIONS A AND B DO
INCLUDE MOLD MISMATCH AND ARE
DETERMINED AT DATUM PLANE –AB–.
7 DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. DAMBAR PROTRUSION SHALL
NOT CAUSE THE D DIMENSION TO EXCEED
0.350 (0.014).
8 MINIMUM SOLDER PLATE THICKNESS SHALL BE
0.0076 (0.0003).
9 EXACT SHAPE OF EACH CORNER IS OPTIONAL.
P
37
1
36
–T–
–U–
B
V
B1
12
25
13
V1
AE
AE
24
DIM
A
A1
B
B1
C
D
E
F
G
H
J
K
M
N
P
Q
R
S
S1
V
V1
W
X
–Z–
S1
S
–T–, –U–, –Z–
4X
DETAIL Y
0.200 (0.008) AC T–U Z
0.080 (0.003) AC
G
M_
–AB–
TOP & BOTTOM
–AC–
ÇÇÇ
ÉÉÉ
ÇÇÇ
ÉÉÉ
ÇÇÇ
AD
BASE METAL
N
C
J
F
D
0.080 (0.003)
M
R
E
MILLIMETERS
MIN
MAX
7.000 BSC
3.500 BSC
7.000 BSC
3.500 BSC
1.400
1.600
0.170
0.270
1.350
1.450
0.170
0.230
0.500 BASIC
0.050
0.150
0.090
0.200
0.500
0.700
12 _REF
0.090
0.160
0.250 BASIC
1_
5_
0.150
0.250
9.000 BSC
4.500 BSC
9.000 BSC
4.500 BSC
0.200 REF
1.000 REF
INCHES
MIN
MAX
0.276 BSC
0.138 BSC
0.276 BSC
0.138 BSC
0.055
0.063
0.007
0.011
0.053
0.057
0.007
0.009
0.020 BASIC
0.002
0.006
0.004
0.008
0.020
0.028
12 _REF
0.004
0.006
0.010 BASIC
1_
5_
0.006
0.010
0.354 BSC
0.177 BSC
0.354 BSC
0.177 BSC
0.008 REF
0.039 REF
GAUGE PLANE
W
H
AC T–U
S
Z
Q_
S
K
DETAIL AD
SECTION AE–AE
0.250 (0.010)
X
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola
data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.
Mfax is a trademark of Motorola, Inc.
How to reach us:
USA / EUROPE / Locations Not Listed: Motorola Literature Distribution;
P.O. Box 5405, Denver, Colorado 80217. 1–303–675–2140 or 1–800–441–2447
JAPAN: Nippon Motorola Ltd.: SPD, Strategic Planning Office, 141,
4–32–1 Nishi–Gotanda, Shagawa–ku, Tokyo, Japan. 03–5487–8488
Customer Focus Center: 1–800–521–6274
Mfax: [email protected] – TOUCHTONE 1–602–244–6609
ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
Motorola Fax Back System
– US & Canada ONLY 1–800–774–1848 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
– http://sps.motorola.com/mfax/
HOME PAGE: http://motorola.com/sps/
6
◊
MC13145/D
MOTOROLA RF/IF DEVICE
DATA