Order this document by MJH11017/D SEMICONDUCTOR TECHNICAL DATA !$"& "$ %" "##$ "# . . . designed for use as general purpose amplifiers, low frequency switching and motor control applications. • High DC Current Gain @ 10 Adc — hFE = 400 Min (All Types) • Collector–Emitter Sustaining Voltage VCEO(sus) = 150 Vdc (Min) — MJH11018, 17 VCEO(sus) = 200 Vdc (Min) — MJH11020, 19 VCEO(sus) = 250 Vdc (Min) — MJH11022, 21 • Low Collector–Emitter Saturation Voltage VCE(sat) = 1.2 V (Typ) @ IC = 5.0 A VCE(sat) = 1.8 V (Typ) @ IC = 10 A • Monolithic Construction ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎ v MAXIMUM RATINGS *Motorola Preferred Device MJH Rating Symbol Collector–Emitter Voltage VCEO VCB Collector–Base Voltage Emitter–Base Voltage 11018 11017 11020 11019 11022 11021 Unit 150 200 250 Vdc 150 200 250 Vdc VEB IC Collector Current — Continuous — Peak (1) Base Current Total Device Dissipation @ TC = 25_C Derate Above 25_C Operating and Storage Junction Temperature Range IB PD TJ, Tstg 5.0 Vdc 15 30 Adc 0.5 Adc 150 1.2 Watts W/_C – 65 to + 150 _C 15 AMPERE DARLINGTON COMPLEMENTARY SILICON POWER TRANSISTORS 150, 200, 250 VOLTS 150 WATTS THERMAL CHARACTERISTICS Characteristic Thermal Resistance. Junction to Case (1) Pulse Test: Pulse Width = 5.0 ms, Duty Cycle Symbol Max Unit RθJC 0.83 _C/W 10%. CASE 340D–01 PD, POWER DISSIPATION (WATTS) 160 140 120 100 80 60 40 20 0 0 20 40 60 80 100 120 TC, CASE TEMPERATURE (°C) 140 160 Figure 1. Power Derating Preferred devices are Motorola recommended choices for future use and best overall value. Motorola, Inc. 1995 Motorola Bipolar Power Transistor Device Data 1 ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎÎ v ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ELECTRICAL CHARACTERISTICS (TC = 25_C unless otherwise noted) Characteristic Symbol Min Max 150 200 250 — — — — — — 1.0 1.0 1.0 — — 0.5 5.0 Unit OFF CHARACTERISTICS Collector–Emitter Sustaining Voltage (1) (IC = 0.1 Adc, IB = 0) VCEO(sus) MJH11017, MJH11018 MJH11019, MJH11020 MJH11021, MJH11022 Collector Cutoff Current (VCE = 75 Vdc, IB = 0) (VCE = 100 Vdc, IB = 0) (VCE = 125 Vdc, IB = 0) Vdc ICEO MJH11017, MJH11018 MJH11019, MJH11020 MJH11021, MJH11022 mAdc Collector Cutoff Current (VCE = Rated VCB, VBE(off) = 1.5 Vdc) (VCE = Rated VCB, VBE(off) = 1.5 Vdc, TJ = 150_C) ICEV mAdc Emitter Cutoff Current (VBE = 5.0 Vdc IC = 0) IEBO — 2.0 mAdc hFE 400 100 15,000 — — VCE(sat) — — 2.5 4.0 Vdc Base–Emitter On Voltage (IC = 10 A, VCE = 5.0 Vdc) VBE(on) — 2.8 Vdc Base–Emitter Saturation Voltage (IC = 15 Adc, IB = 150 mA) VBE(sat) — 3.8 Vdc fT 3.0 — — Cob — — 400 600 pF hfe 75 — — Symbol NPN PNP Unit Delay Time td 150 75 ns Rise Time tr 1.2 0.5 µs ts 4.4 2.7 µs tf 2.5 2.5 µs ON CHARACTERISTICS (1) DC Current Gain (IC = 10 Adc, VCE = 5.0 Vdc) DC Current Gain (IC = 15 Adc, VCE = 5.0 Vdc) Collector–Emitter Saturation Voltage (IC = 10 Adc, IB = 100 mA) Collector–Emitter Saturation Voltage (IC = 15 Adc, IB = 150 mA) DYNAMIC CHARACTERISTICS Current–Gain Bandwidth Product (IC = 10 Adc, VCE = 3.0 Vdc, f = 1.0 MHz) Output Capacitance (VCB = 10 Vdc, IE = 0, f = 0.1 MHz) MJH11018, MJH11020, MJH11022 MJH11017, MJH11019, MJH11021 Small–Signal Current Gain (IC = 10 Adc, VCE = 3.0 Vdc, f = 1.0 kHz) SWITCHING CHARACTERISTICS Typical Characteristic Storage Time (VCC = 100 V, IC = 10 A, IB = 100 mA VBE(off) = 5.0 V) (See Figure 2) Fall Time (1) Pulse Test: Pulse Width = 300 µs, Duty Cycle 2.0%. VCC 100 V RC SCOPE TUT RB & RC varied to obtain desired current levels D1, must be fast recovery types, e.g.: 1N5825 used above IB ≈ 100 mA MSD6100 used below IB ≈ 100 mA tr, tf ≤ 10 ns Duty Cycle = 1.0% V2 APPROX +12 V 0 V1 APPROX – 8.0 V RB 51 25 µs D1 + 4.0 V For td and tr, D1 is disconnected and V2 = 0 For NPN test circuit, reverse diode and voltage polarities. Figure 2. Switching Times Test Circuit 2 Motorola Bipolar Power Transistor Device Data r(t), EFFECTIVE TRANSIENT THERMAL RESISTANCE (NORMALIZED) 1.0 0.7 0.5 D = 0.5 0.3 0.2 0.2 0.1 0.1 0.07 0.05 0.02 0.03 0.01 SINGLE PULSE 0.02 0.01 0.01 0.02 0.03 0.05 P(pk) RθJC(t) = r(t) RθJC RθJC = 0.83°C/W MAX D CURVES APPLY FOR POWER PULSE TRAIN SHOWN READ TIME AT t1 TJ(pk) – TC = P(pk) RθJC(t) 0.05 0.1 0.2 0.3 0.5 1.0 2.0 3.0 5.0 t, TIME (ms) 10 20 30 t1 t2 DUTY CYCLE, D = t1/t2 50 100 200 300 500 1000 IC, COLLECTOR CURRENT (AMPS) Figure 3. Thermal Response FORWARD BIAS TC = 25°C SINGLE PULSE 30 20 0.1 ms 10 0.5 ms 1.0 ms 5.0 5.0 ms dc WIRE BOND LIMIT THERMAL LIMIT SECOND BREAKDOWN LIMIT MJH11017, MJH11018 MJH11019, MJH11020 MJH11021, MJH11022 2.0 1.0 0.5 0.2 0 2.0 3.0 5.0 10 20 30 50 100 150 250 VCE, COLLECTOR–EMITTER VOLTAGE (VOLTS) There are two limitations on the power handling ability of a transistor: average junction temperature and second breakdown. Safe operating area curves indicate IC – VCE limits of the transistor that must be observed for reliable operation; i.e., the transistor must not be subjected to greater dissipation than the curves indicate. The data of Figure 4 is based on T J(pk) = 150_C; TC is variable depending on conditions. Second breakdown pulse limits are valid for duty cycles to 10% provided T J(pk) 150 _ C. T J(pk) may be calculated from the data in Figure 3. At high case temperatures, thermal limitations will reduce the power that can be handled to values less than the limitations imposed by second breakdown. v Figure 4. Maximum Rated Forward Bias Safe Operating Area (FBSOA) REVERSE BIAS IC, COLLECTOR CURRENT (AMPS) 30 20 L = 200 µH IC/IB1 ≥ 50 TC = 100°C VBE(off) = 0 – 5.0 V RBE = 47 Ω DUTY CYCLE = 10% 10 MJH11017, MJH11018 MJH11019, MJH11020 MJH11021, MJH11022 0 0 20 For inductive loads, high voltage and high current must be sustained simultaneously during turn–off, in most cases, with the base to emitter junction reverse biased. Under these conditions the collector voltage must be held to a safe level at or below a specific value of collector current. This can be accomplished by several means such as active clamping, RC snubbing, load line shaping, etc. The safe level for these devices is specified as Reverse Bias Safe Operating Area and represents the voltage–current conditions during reverse biased turn–off. This rating is verified under clamped conditions so that the device is never subjected to an avalanche mode. Figure 5 gives RBSOA characteristics. 220 260 140 60 100 180 VCE, COLLECTOR–EMITTER VOLTAGE (VOLTS) Figure 5. Maximum Rated Reverse Bias Safe Operating Area (RBSOA) Motorola Bipolar Power Transistor Device Data 3 PNP 10,000 10,000 7000 5000 VCE = 5.0 V 3000 2000 TC = 150°C 1000 25°C 500 – 55°C 200 100 VCE = 5.0 V 5000 hFE, DC CURRENT GAIN hFE, DC CURRENT GAIN NPN TC = 150°C 2000 25°C 1000 500 – 55°C 200 100 0.2 0.5 0.7 0.3 1.0 3.0 5.0 10 0.2 15 0.3 0.5 0.7 1.0 3.0 5.0 7.0 10 15 IC, COLLECTOR CURRENT (AMPS) IC, COLLECTOR CURRENT (AMPS) Figure 6. DC Current Gain NPN 4.5 4.0 VCE , COLLECTOR–EMITTER VOLTAGE (VOLTS) VCE , COLLECTOR–EMITTER VOLTAGE (VOLTS) PNP TJ = 25°C 3.5 3.0 2.5 IC = 15 A 2.0 IC = 10 A 1.5 1.0 1.0 IC = 5.0 A 2.0 3.0 5.0 10 20 30 50 100 200 300 500 1000 4.5 4.0 TJ = 25°C 3.5 3.0 IC = 15 A 2.5 2.0 IC = 10 A 1.5 1.0 1.0 IC = 5.0 A 2.0 3.0 5.0 IB, BASE CURRENT (mA) 10 20 30 50 100 200 300 500 1000 IB, BASE CURRENT (mA) Figure 7. Collector Saturation Region PNP NPN 4.0 4.0 3.5 3.5 TJ = 25°C VOLTAGE (VOLTS) VOLTAGE (VOLTS) 3.0 2.5 VBE(sat) @ IC/IB = 100 2.0 1.5 TJ = 25°C 3.0 2.5 VBE(sat) @ IC/IB = 100 2.0 1.5 VBE @ VCE = 5.0 V VBE @ VCE = 5.0 V 1.0 1.0 VCE(sat) @ IC/IB = 100 0.5 0.2 0.3 0.5 0.7 1.0 2.0 3.0 5.0 7.0 10 20 VCE(sat) @ IC/IB = 100 0.5 0.2 0.5 0.7 1.0 2.0 5.0 10 IC, COLLECTOR CURRENT (AMPS) IC, COLLECTOR CURRENT (AMPS) Figure 8. “On” Voltages 4 Motorola Bipolar Power Transistor Device Data 20 PNP MJH11017 MJH11019 MJH11021 NPN MJH11018 MJH11020 MJH11022 COLLECTOR BASE COLLECTOR BASE EMITTER EMITTER Figure 9. Darlington Schematic Motorola Bipolar Power Transistor Device Data 5 PACKAGE DIMENSIONS C Q B U S NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. E DIM A B C D E G H J K L Q S U V 4 A L 1 2 3 K D J STYLE 1: PIN 1. 2. 3. 4. H V MILLIMETERS MIN MAX 19.00 19.60 14.00 14.50 4.20 4.70 1.00 1.30 1.45 1.65 5.21 5.72 2.60 3.00 0.40 0.60 28.50 32.00 14.70 15.30 4.00 4.25 17.50 18.10 3.40 3.80 1.50 2.00 G INCHES MIN MAX 0.749 0.771 0.551 0.570 0.165 0.185 0.040 0.051 0.058 0.064 0.206 0.225 0.103 0.118 0.016 0.023 1.123 1.259 0.579 0.602 0.158 0.167 0.689 0.712 0.134 0.149 0.060 0.078 BASE COLLECTOR EMITTER COLLECTOR CASE 340D–01 SOT 93, TO–218 TYPE ISSUE A Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters can and do vary in different applications. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA / EUROPE: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, Toshikatsu Otsuki, 6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–3521–8315 MFAX: [email protected] – TOUCHTONE (602) 244–6609 INTERNET: http://Design–NET.com HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298 6 ◊ Motorola Bipolar Power Transistor Device Data *MJH11017/D* MJH11017/D