Order this document by MRFIC0931/D SEMICONDUCTOR TECHNICAL DATA The MRFIC Line The MRFIC0931 is a balanced Gilbert cell mixer with LO buffer amplifier intended for transmit upmixer application. The device is usable for Industrial, Scientific and Medical (ISM), Cellular and PCS applications and is packaged in a low–cost surface mount package. • Usable 500–2000 MHz • High Output Power @ 1 dB Gain Compression, 3.6 Volts 0.9 dBm (Typ) @ 900 MHz –2 dBm (Typ) @ 1800 MHz • 2.7–4.8 Volts Operation • Balanced Design for Good LO Rejection • 47 mA (Max) Current @ 4.5 Volts 45 mA (Max) Current @ 3.6 Volts • Low Cost Surface Mount Package • Order MRFIC0931R2 for Tape and Reel. R2 suffix = 2,500 Units per 12 mm, 13 inch Reel. • Device Marking = M0931 BALANCED TRANSMIT MIXER SILICON MONOLITHIC INTEGRATED CIRCUIT CASE 751-05 (SO-8) ABSOLUTE MAXIMUM RATINGS Ratings Supply Voltage Input Power, IF and LO Operating Ambient Temperature Storage Temperature Symbol Value Unit VCC 5 Vdc PIF, PLO +10 dBm TA – 35 to + 85 °C Tstg – 65 to +150 °C RF OUT 1 8 RF OUT GND 2 7 VCC GND 3 6 IF IN IF IN 4 5 LO IN Pin Connections and Functional Block Diagram REV 1 RF DEVICE DATA MOTOROLA Motorola, Inc. 1997 MRFIC0931 1 RECOMMENDED OPERATING CONDITIONS Parameter Symbol Value Unit Supply Voltages VCC 2.7 to 4.5 Vdc RF Frequency Range fRF 500 to 2000 MHz IF Frequency Range fIF 0 to 250 MHz ELECTRICAL CHARACTERISTICS (TA = 25°C, measured in circuit shown in Figure 1 or 2 as frequency indicates) Parameter Min Typ Max Unit RF Output Power (fIF = 88 MHz, fLO = 815 MHz, PLO = –10 dBm, PIF = –20 dBm, VCC = 4.5 V) 2 4 8 dBm LO Feed Through (fIF = 88 MHz, fLO = 815 MHz, PLO = –10 dBm, PIF = –20 dBm, VCC = 4.5 V) — — –16 dBc Undesired Sideband Output (fIF = 88 MHz, fLO = 815 MHz, PLO = –10 dBm, PIF = –20 dBm, VCC = 4.5 V) — — – 25 dBc Small Sigal Conversion Gain (fIF = 100 MHz, PIF = –25 dBm, VCC = 3.6 V) 900 MHz (PLO = –10 dBm) 1800 MHz (PLO = –5 dBm) — — 25 20 — — dB dB Power Output at 1 dB Gain Compression (fIF = 100 MHz, PIF = –25 dBm, VCC = 3.6 V) 900 MHz (PLO = –10 dBm) 1800 MHz (PLO = –5 dBm) — — 0.9 –2 — — dBm dBm Supply Current VCC = 4.5 V VCC = 3.6 V — — 38 30 47 45 mA mA C10 RF OUTPUT L4 T1 C8 T2 C9 1 8 2 7 C7 C5 VCC C6 L3 3 6 C4 L2 4 IF IN LO IN 5 C3 C1 C2 L1 C1, C4, C6, C10 C2 C3, C9 C5 C7 C8 1000 pF 13 pF 10 pF 100 pF 2.4 pF 2 pF L1, L3 L2 L4 T1, T2 Board Material 220 nH 3.3 nH 12 nH 1/8 λ 50 Ω Microstrip Epoxy/Glass εr = 4.45 Figure 1. 903 MHz Configuration Test Circuit MRFIC0931 2 MOTOROLA RF DEVICE DATA C10 RF OUTPUT L3 T1 C8 T2 C9 1 8 2 7 C7 C5 3 6 C4 L2 4 IF IN C3 LO IN 5 C11 C1 C2 VCC C6 L1 C1, C6, C10 C2 C3, C4, C5, C8 C7 C9 C11 L1, L2 L3 T1, T2 Board Material 1000 pF 10 pF 100 pF 1.2 pF 2.7 pF 1 pF 180 nH 3.3 nH 2.7 nH 1/8 λ 50 Ω Microstrip Epoxy/Glass εr = 4.45 Figure 2. 1800 MHz Applications Circuit MOTOROLA RF DEVICE DATA MRFIC0931 3 PACKAGE DIMENSIONS D A NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. DIMENSIONS ARE IN MILLIMETERS. 3. DIMENSION D AND E DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE. 5. DIMENSION B DOES NOT INCLUDE MOLD PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 TOTAL IN EXCESS OF THE B DIMENSION AT MAXIMUM MATERIAL CONDITION. C 8 5 0.25 H E M B M 1 4 h B X 45 _ e q A C SEATING PLANE L 0.10 A1 B 0.25 M C B S A S DIM A A1 B C D E e H h L q MILLIMETERS MIN MAX 1.35 1.75 0.10 0.25 0.35 0.49 0.18 0.25 4.80 5.00 3.80 4.00 1.27 BSC 5.80 6.20 0.25 0.50 0.40 1.25 0_ 7_ CASE 751–05 ISSUE S Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. Mfax is a trademark of Motorola, Inc. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 5405, Denver, Colorado 80217. 303–675–2140 or 1–800–441–2447 JAPAN: Nippon Motorola Ltd.: SPD, Strategic Planning Office, 4–32–1, Nishi–Gotanda, Shinagawa–ku, Tokyo 141, Japan. 81–3–5487–8488 Mfax: [email protected] – TOUCHTONE 602–244–6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, – US & Canada ONLY 1–800–774–1848 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298 INTERNET: http://motorola.com/sps MRFIC0931 4 ◊ MRFIC0931/D MOTOROLA RF DEVICE DATA