P600A THRU P600M HIGH CURRENT PLASTIC SILICON RECTIFIER VOLTAGE - 50 to 1000 Volts CURRENT - 6.0 Amperes FEATURES l High surge current capability l Plastic package has Underwriters Laboratory P600 Flammability Classification 94V-O Utilizing Flame Retardant Epoxy Molding Compound l l Void-free plastic in a P600 package High current operation 6.0 Amperes @ TA=55 ¢J l Exceeds environmental standards of MIL-S-19500/228 MECHANICAL DATA Case: Molded plastic, P600 Terminals: axial leads, solderable per MIL-STD-202, Method 208 Polarity: Color band denotes cathode Mounting Position: Any Weight: 0.07 ounce, 2.1 gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS *@ TA=25 ¢J unless otherwise specified. Single phase, half-wave,60 Hz, resistive or inductive load. **All values except Maximum RMS Voltage are registered JEDEC parameters. P600A P600B P600D P600G P600J P600K P600M UNITS Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current TA=55 ¢J Maximum Overload Surge Current at 1 cycle (NOTE 1) Maximum Forward Voltage at 6.0 ADC Maximum DC Reverse Current @TA=25 ¢J Rated DC Blocking Voltage @TA=100 ¢J Typical Junction capacitance (Note 3) CJ Typical Thermal Resistance (Note 2) R £KJA Typical Thermal Resistance (Note 2) R £KJL Operating Temperature Range Storage Temperature Range 50 35 50 100 70 100 200 140 200 400 280 400 600 420 600 6.0 400 1.0 10 1.0 150 20.0 4.0 -55 to +150 -55 to +150 800 560 800 1000 700 1000 V V V ¡C A A A V £g A m ADC PF ¢J /W ¢J /W ¢J ¢J NOTES: 1. Peak forward surge current, per 8.3ms single half-sine-wave superimposed on rated load(JECED method) 2. Thermal resistance from junction to ambient and from junction to lead at 0.375"(9.5mm) lead length P.C.B. mounted with 1.1×1.1”(30×30mm) copper pads 3. Measured at 1 MHZ and applied reverse voltage of 4.0 volts RATING AND CHARACTERISTIC CURVES INSTANTANEOUS REVERSE CURRENT, £g A P600A THRU P600M AVERAGE FORWARD CURRENT (Io)-AMP (Io)-AAV 100 10 25 ¢J 1 8.0 6.0 0.5" LOAD LENGTH 4.0 2.0 0 50 75 100 125 150 175 200 AMBIENT TEMPERATURE (TA) - ¢J 0.1 0 20 40 60 80 100 120 140 Fig. 2-FORWARD DERATING CURVE PERCENT OF RATED PEAK REVERSE VOLTAGE Fig. 1-TYPICAL REVERSE CHARACTERISTICS 100 10 1 0.1 0.01 0.1 1 10 100 INSTANTANEOUS FORWARD CURRENT, MICROAMPERES RANSIENT THERMAL IMPEDANCE, ¢J /W 100 10 1 0.1 TJ = 25 ¢J PULSE WIDTH = 300uS 1% DUTY CYCLE t, PULSE DURATION, sec. 0.01 0.6 0.8 1.0 1.2 1.4 1.6 1.8 Fig. 3-TYPICAL TRANSIENT THERMAL IMPEDANCE FORWARD SURGE CURRENT, Apk (HALF SINE-WAVE) INSTANTANEOUS FORWARD VOLTAGE, VOLTS Fig. 4-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 400 320 240 160 T A = 60 ¢J 80 0 1 2 6 10 20 40 60 100 NO. OF CYCLES AT 60Hz Fig. 5-MAXIMUM OVERLOAD SURGE CURRENT