Features Regulated Converters ● ● ● ● ● ● ● ● ● ● ● ● POWERLINE 2:1 Wide Input Voltage Range 5 Watts Regulated Output Power 1.6kVDC Isolation Suffix “H “3kVDC Isolation Low Profile, 10.2 mm Height Over Current Protection Five-Sided Shield No Derating to 71°C Non-Conductive Black Plastic Ideal for Telecom/Networking Standard DIP24 and SMD-Pinning Efficiency to 81% DC/DC-Converter RP05S_DF Series Selection Guide 5V, 12V, 24V and 48V Input Types Output Voltage VDC Output Current mA Input (4) Current mA Efficiency(5) DIP24 (SMD) Input Range VDC % Capacitive(6) Load max. µF RP05-123.3SF** 9-18 3.3 1000 404 72 2200 RP05-1205SF** 9-18 5 1000 579 76 1000 RP05-1212SF** 9-18 12 470 618 80 220 RP05-1215SF** 9-18 15 400 658 80 150 RP05-243.3SF** 18-36 3.3 1000 202 72 2200 RP05-2405SF** 18-36 5 1000 278 79 1000 RP05-2412SF** 18-36 12 470 306 81 220 RP05-2415SF** 18-36 15 400 325 81 150 RP05-483.3SF** 36-75 3.3 1000 100 73 2200 RP05-4805SF** 36-75 5 1000 141 78 1000 RP05-4812SF** 36-75 12 470 153 81 220 RP05-4815SF** 36-75 15 400 162 81 150 RP05-1205DF** 9-18 ±5 ±500 571 77 ±680 RP05-1212DF** 9-18 ±12 ±230 605 80 ±100 RP05-1215DF** 9-18 ±15 ±190 625 80 ±68 RP05-2405DF** 18-36 ±5 ±500 282 78 ±680 RP05-2412DF** 18-36 ±12 ±230 299 81 ±100 RP05-2415DF** 18-36 ±15 ±190 309 81 ±68 RP05-4805DF** 36-75 ±5 ±500 143 77 ±680 RP05-4812DF** 36-75 ±12 ±230 149 81 ±100 RP05-4815DF** 36-75 ±15 ±190 154 81 ±68 Part Number 5 Watt DIP24 & SMD, Single & Dual Output ** add Suffix SMD for SMD package Description The F-Series of DC/DC Converters are fully certified to EN 60950: 2000. This makes them ideal for all Telecom and safety applications where approved isolation is required. 198 April-2005 www.recom-international.com RP05-S_DF Series POWERLINE DC/DC-Converter Derating-Graph (Ambient Temperature) RP05-4805SF 125 100 Output Power (%) 75 50 Natural Convection 25 0 -25 -10 0 50 60 70 Ambient Temperature Range (°C) 71 80 90 100 Derating graphes are valid only for the shown part numbers. If you need detailed derating-information about a part-number not shown here please contact our technical customer service at [email protected] Specifications (typical at nominal input and 25°C unless otherwise noted) Input Voltage Range 12V nominal input 24V nominal input 48V nominal input Input Filter Input Surge Voltage (100 ms max.) 9-18VDC 18-36VDC 36-75VDC Pi Type 12V Input 24V Input 48V Input 36VDC 50VDC 100VDC Input Reflected Ripple (nominal Vin and full load) 150mAp-p Start Up Time (nominal Vin and constant resistor load) 30ms typ. Output Power 5W max. Output Voltage Accuracy (full Load and nominal Vin) ±2% Minimum Load (see Note 1) 10% of FL Line Regulation (LL-HL at full load) Load Regulation (25% to 100% FL) ±0.2% Single Dual Cross Regulation (asymmetrical load 25%/100% FL) Ripple and Noise (20MHz bandwith) ±0.5% ±2% ±5% 3.3V, 5V others Temperature Coefficient 75mVp-p 1%/p-p of Vout max. ±0.02%/°C, max. Transient Response (25% load step change) 500µS Over Load Protection (% of full load at nominal Vin) 180% typ Short Circuit Protection Continuous, automatic recovery continued on next page www.recom-international.com April-2005 199 RP05-S_DF Series POWERLINE DC/DC-Converter Specifications (typical at nominal input and 25°C unless otherwise noted) Efficiency Isolation Voltage see „Selection Guide“ table In to out Standard Suffix /H 1.600VDC min. 3.000VDC min. Isolation Resistance 109 Ω min. Isolation Capacitance 300pF max. Operating Frequency 100kHz min. Approved to Safety Standards EN60950 Operating Temperature Range -25°C to +71°C Storage Temperature Range -55°C to +105°C Thermal Shock MIL-STD-810D Vibration 10-55Hz, 2G, 30 Min. along X, Y and Z Relative Humidity 5% to 95% RH Case Material Non-conductive black plastic Base Material Non-conductive black plastic Potting Material Epoxy (UL94-V0) Conducted Emissions Radiated Emissions ESD Radiated Immunity Fast Transient Surge Conducted Immunity EN55022 EN55022 EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 Level A Level A Perf. Criteria 2 Perf. Criteria 2 Perf. Criteria 2 Perf. Criteria 2 Perf. Criteria 2 Weight DIP SMD 14g 15g Dimensions DIP SMD 31.8 x 20.3 x 10.2mm 32.0 x 20.3 x 10.9mm 3.731 x 106 Hours MTBF (see note 2) Notes : 1. The RP05 series requires a minimum of 10% loading on the output to maintain specified regulation. Operation under no-load condition will not damage these devices, however they may not meet all listed specification. 2. BELLCORE TR-NWT-000332. Case l: 50% Stress, Temperature at 40°C (Ground fixed and controlled environment). H” for 3.000VDC Isolation 3. Suffix “H 4. Maximum value at nominal input voltage and full load of standard type. 5. Typical value at nominal input voltage and full load. 6. Test by minimum Vin and constant resistor load. 7. See application notes for EMI-filtering. 200 April-2005 www.recom-international.com RP05-S_DF Series POWERLINE DC/DC-Converter Package Style and Pinning (mm) DIP24 Package Style 3rd angle projection 31.80 20.30 10.20 3.8 4.60 5.10 17.80 15.20 Pin Connections Pin # 2 3 9 10 11 14 15 16 22 23 NC = No Connection 0.25 x 0.50 Rectangular Pin 9 10 11 2 3 Bottom View 16 15 14 23 22 Single –Vin –Vin NC NC NC +Vout NC –Vout +Vin +Vin Dual –Vin –Vin Com NC –Vout +Vout NC Com +Vin +Vin Pin Pitch Tolerance ±0.35 mm SMD Package Style 32.00 20.30 31.40 SMD Package Style 11.20 2.54 Same spec. as the original DIP spec. and pin definition, excl. of the SMD type pin. 10.90 3.81 21.30 6.35 25.40 Pin Connections Pin # Pin area 0.1 x 0.50 2.54 0.50 1.60 2.40 9 10 11 12 1 2 3 4 5 23.40 Bottom View 26.54 24.14 24 23 22 21 20 16 15 14 13 11 x 2.54 www.recom-international.com Top View 1 27.94 April-2005 2 3 9 10 11 14 15 16 22 23 Others NC = No Connection Single –Vin –Vin NC NC NC +Vout NC –Vout +Vin +Vin NC Dual –Vin –Vin Com NC –Vout +Vout NC Com +Vin +Vin NC Pin Pitch Tolerance ±0.35 mm 201