Features Regulated Converters ● ● ● ● ● ● ● ● ● ● POWERLINE 2:1 Wide Input Voltage Range 8 Watts Regulated Output Power 1.6kVDC Isolation ULCertified Low Profile, 10.2 mm Height Over Current Protection Five-Sided Shield No Derating to 71°C Standard DIP24 and SMD-Pinning Efficiency to 85% DC/DC-Converter RP08S_DA Series Selection Guide 5V, 12V, 24V and 48V Input Types DIP24 (SMD) Input Range VDC Output Voltage VDC Output Current mA Input (4) Current mA RP08-123.3SA** 9-18 3.3 2000 724 80 3300 RP08-1205SA** 9-18 5 1500 801 82 1600 RP08-1212SA** 9-18 12 666 833 84 350 Part Number Efficiency(5) Capacitive(6) Load max. % µF RP08-1215SA** 9-18 15 533 843 83 240 RP08-243.3SA** 18-36 3.3 2000 362 80 3300 RP08-2405SA** 18-36 5 1500 396 83 1600 RP08-2412SA** 18-36 12 666 416 84 350 RP08-2415SA** 18-36 15 533 416 84 240 RP08-483.3SA** 36-75 3.3 2000 181 80 3300 RP08-4805SA** 36-75 5 1500 198 83 1600 RP08-4812SA** 36-75 12 666 208 84 350 RP08-4815SA** 36-75 15 533 208 84 240 RP08-1205DA** 9-18 ±5 ±800 843 83 ±1000 RP08-1212DA** 9-18 ±12 ±333 833 84 ±160 RP08-1215DA** 9-18 ±15 ±267 834 84 ±100 RP08-2405DA** 18-36 ±5 ±800 427 82 ±1000 RP08-2412DA** 18-36 ±12 ±333 422 83 ±160 RP08-2415DA** 18-36 ±15 ±267 411 85 ±100 RP08-4805DA** 36-75 ±5 ±800 211 83 ±1000 RP08-4812DA** 36-75 ±12 ±333 206 85 ±160 RP08-4815DA** 36-75 ±15 ±267 206 85 ±100 8 Watt DIP24 & SMD, Single & Dual Output UL-60950-1 Certified ** add Suffix SMD for SMD package Description The A-Series of DC/DC Converters are fully certified to EN 60950: 2000. This makes them ideal for all Telecom and safety applications where approved isolation is required. They also meet UL 1950 and CSA 950 standards. 212 14-February-2007 www.recom-international.com POWERLINE RP08-S_DA Series DC/DC-Converter Derating-Graph (Ambient Temperature) RP08-4805SA 125 100 Output Power (%) 75 50 Natural Convection 25 0 -40 -25 -10 0 50 60 70 80 90 100 Ambient Temperature Range (°C) 65 Derating graphs are valid only for the shown part numbers. If you need detailed derating-information about a part-number not shown here please contact our technical customer service at [email protected] Specifications (typical at nominal input and 25°C unless otherwise noted) Input Voltage Range (see Note 3) 12V nominal input 24V nominal input 48V nominal input Input Filter Input Surge Voltage (100 ms max.) Pi Type 12V Input 24V Input 48V Input Input Reflected Ripple (nominal Vin and full load) Remote OFF input current 600ms typ. DC-DC ON DC-DC OFF Nominal input Output Power Open or 3.0V < Vr < 12V Short or 0V < Vr < 1.2V 2.5mA 8W max. Output Voltage Accuracy (full Load and nominal Vin) ±2% Minimum Load (see Note 1) 10% of full load Line Regulation (low line, high line at full load) Load Regulation (25% to 100% full load) 36VDC 50VDC 100VDC 20mAp-p Start Up Time (nominal Vin and constant resistor load) Remote ON/OFF (see Note 7) 9-18VDC 18-36VDC 36-75VDC ±0.2% Single Dual Cross Regulation (asymmetrical load 25%/100% full load) ±0.5% ±1% ±5% Ripple and Noise (20MHz bandwith) 50mVp-p Temperature Coefficient ±0.02%/°C max. Transient Response (25% load step change) 200µs continued on next page www.recom-international.com 14-February-2007 213 RP08-S_DA Series POWERLINE DC/DC-Converter Specifications (typical at nominal input and 25°C unless otherwise noted) Over Load Protection (% of full load at nominal Vin) 150% typ Short Circuit Protection Continuous, automatic recovery Efficiency Isolation Voltage see „Selection Guide“ table In to out I/O to case I/O to case 1600VDC min. DIP type 1600VDC min. SMD type 1000VDC min. Isolation Resistance 1 GΩ min. Isolation Capacitance 300pF max. Operating Frequency 100kHz min. Approved to Safety Standards UL 1950, EN60950 Operating Temperature Range -40°C to +85°C(with derating) Maximum Case Temperature +100°C Storage Temperature Range -55°C to +105°C Thermal Impedance Natural convection 20°C/Watt Thermal Shock MIL-STD-810D Vibration 10-55Hz, 2G, 30 Min. along X, Y and Z Relative Humidity 5% to 95% RH Case Material Nickel plated copper Base Material Non-conductive black plastic Potting Material Epoxy (UL94-V0) Conducted Emissions (see Note 8) Radiated Emissions ESD Radiated Immunity Fast Transient Surge Conducted Immunity EN55022 EN55022 EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 Level A Level A Perf. Criteria 2 Perf. Criteria 2 Perf. Criteria 2 Perf. Criteria 2 Perf. Criteria 2 Weight DIP SMD 16g 18g Dimensions DIP SMD 31.8 x 20.3 x 10.2mm 32.0 x 20.3 x 10.9mm 3165 x 103 hours MTBF (see Note 2) Notes : 1. The RP08 series requires a minimum of 10% loading on the output to maintain specified regulation. Operation under no-load condition will not damage these devices, however they may not meet all listed specification. 2. BELLCORE TR-NWT-000332. Case l: 50% Stress, Temperature at 40°C (Ground fixed and controlled environment). 3. Start up voltage : 10VDC 4. Maximum value at nominal input voltage and full load of standard type. 5. Typical value at nominal input voltage and full load. 6. Test by minimum Vin and constant resistor load. 7. The ON/OFF control pin voltage is referenced to negative input. 8. See application notes for EMI-filtering. 214 14-February-2007 www.recom-international.com RP08-S_DA Series POWERLINE DC/DC-Converter Package Style and Pinning (mm) DIP24 Package Style 3rd angle projection 31.80 20.30 10.20 3.8 2 5.10 20.30 2.54 15.20 Pin Connections Pin # Single 1 ON/OFF 2 -Vin 3 -Vin 9 NC 11 NC 14 +Vout 16 -Vout 22 +Vin 23 +Vin NC = No Connection 0.25 x 0.50 Rectangular Pin 9 11 16 14 1 2 3 Bottom View 23 22 Dual ON/OFF -Vin -Vin Com -Vout +Vout Com +Vin +Vin Pin Pitch Tolerance ±0.35 mm SMD Package Style 32.00 20.30 31.40 SMD Package Style 11.20 2.54 Same spec. as the original DIP spec. and pin definition, excl. of the SMD type pin. 10.90 3.81 21.30 6.35 25.40 Pin area 0.1 x 0.50 2.54 0.50 Pin Connections 1.60 2.40 9 10 11 12 1 2 3 4 5 23.40 Bottom View 26.54 Top View 24.14 24 23 22 21 20 16 15 14 13 11 x 2.54 www.recom-international.com 1 Pin # Single 1 ON/OFF 2 -Vin 3 -Vin 9 NC 11 NC 14 +Vout 16 -Vout 22 +Vin 23 +Vin Others NC NC = No Connection Dual ON/OFF -Vin -Vin Com -Vout +Vout Com +Vin +Vin NC Pin Pitch Tolerance ±0.35 mm 27.94 14-February-2007 215