SANYO 20SVP68M

OS-CON DATA SHEET
No.OS02N-DFSVP036
OS-CON 20SVP68M
Frequency (kHz)
Impedance (ohm)
ESR (ohm)
0.12
17.943
0.910
0.5
4.539
0.362
1
2.345
0.238
10
0.285
0.078
100
0.052
0.036
500
0.026
0.026
1000
0.037
0.024
5000
0.155
0.029
10000
0.304
0.027
Frequency characteristics
1000
Impedance (ohm)
ESR (ohm)
ESR, Impedance (ohm)
100
10
1
0.1
0.01
0.001
0.1
1
10
100
1000
10000
Frequency (kHz)
Measureing equipment: HP4194A
Test fixture: HP16047C
Measuring position: root of leads
OS Engineering Department, OS-CON Control Department
Saga SANYO Industries Co., Ltd.
n = 3p.(Ave.)
Room temperature
OS-CON DATA SHEET
SVP series
Test item
Endurance
(After V.P.S test)
Test temperature
105 deg.C
Model
Applied voltage
20 V
Lot No.
20SVP68M
142003241
Tangent of loss angle (120Hz)
Change in capacitance (120Hz)
Tangent of loss angle
20
Percent delta (%)
10
0
-10
-20
-30
-40
2000
0
Time[h]
ESR (100kHz)
Leakage current (20V 60s)
10000
100
90
80
70
60
50
40
30
20
10
0
1000
100
10
1
0.1
0.01
0
2000
Time[h]
Note:
2000
Time[h]
Leakage current(µA)
ESR(mohm)
0
0.15
0.14
0.13
0.12
0.11
0.1
0.09
0.08
0.07
0.06
0.05
0.04
0.03
0.02
0.01
0
0
2000
Time[h]
n =30p.
Note: V.P.S test conditions : 230deg.C×75s×2times
(V.P.S = Vapor Phase Soldering method)
Start on August 23, 2001
Executed by M. Koyama
End on November 14, 2001
Drawn by M. Kimura
No.OS02D-DESVP036
OS Engineering Department, OS-CON Control Department, Saga SANYO Industries Co., Ltd.
OS-CON DATA SHEET
SVP series
Test item
Damp heat (Steady state)
(After V.P.S test)
Test temperature
60 deg.C
Model
Test humidity
90 % RH
Lot No.
20SVP68M
220903261
Change in capacitance (120Hz)
Tangent of loss angle (120Hz)
Tangent of loss angle
20
Percent delta (%)
10
0
-10
-20
-30
-40
1000
0
Time[h]
ESR (100kHz)
Leakage current (20V 60s)
100
90
80
70
60
50
40
30
20
10
0
10000
1000
100
10
1
0.1
0.01
0
1000
Time[h]
Note:
1000
Time[h]
Leakage current(µA)
ESR(mohm)
0
0.15
0.14
0.13
0.12
0.11
0.1
0.09
0.08
0.07
0.06
0.05
0.04
0.03
0.02
0.01
0
0
1000
Time[h]
n =20p.
Note: V.P.S test conditions : 230deg.C×75s×2times
(V.P.S = Vapor Phase Soldering method)
Start on April 1, 2002
Executed by M. Koyama
End on May 14, 2002
Drawn by M. Kimura
No.OS02D-DHSVP036
OS Engineering Department, OS-CON Control Department, Saga SANYO Industries Co., Ltd.