SANYO OS-CON20SVP150M

OS-CON DATA SHEET
No.OS02N-DFSVP055
OS-CON 20SVP150M
Frequency (kHz)
Impedance (ohm)
ESR (ohm)
0.12
8.650
0.089
0.5
2.159
0.040
1
1.050
0.030
10
0.110
0.019
100
0.016
0.012
500
0.018
0.010
1000
0.036
0.010
5000
0.167
0.011
10000
0.305
0.011
Frequency characteristics
1000
Impedance (ohm)
ESR (ohm)
ESR, Impedance (ohm)
100
10
1
0.1
0.01
0.001
0.1
1
10
100
1000
10000
Frequency (kHz)
Measureing equipment: HP4194A
Test fixture: HP16047C
Measuring position: root of leads
OS Engineering Department, OS-CON Control Department
Saga SANYO Industries Co., Ltd.
n = 3p.(Ave.)
Room temperature
OS-CON DATA SHEET
SVP series
Test item
Endurance
(After V.P.S test)
Test temperature
105 deg.C
Model
Applied voltage
20 V
Lot No.
20SVP150M
041205221
Tangent of loss angle (120Hz)
Change in capacitance (120Hz)
Tangent of loss angle
20
Percent delta [%]
10
0
-10
-20
-30
-40
2000
0
Time[h]
ESR (100kHz)
Leakage current (20V 60s)
10000
100
90
80
70
60
50
40
30
20
10
0
1000
100
10
1
0.1
0.01
0
2000
Time[h]
Note:
2000
Time[h]
Leakage current(µA)
ESR(mohm)
0
0.15
0.14
0.13
0.12
0.11
0.1
0.09
0.08
0.07
0.06
0.05
0.04
0.03
0.02
0.01
0
0
2000
Time[h]
n =30p.
Note: V.P.S test conditions : 230deg.C×75s×2times
(V.P.S = Vapor Phase Soldering method)
Start on April 20, 2000
Executed by M. Koyama
End on July 13, 2000
Drawn by M. Kimura
No.OS02D-DESVP055
OS Engineering Department, OS-CON Control Department, Saga SANYO Industries Co., Ltd.
OS-CON DATA SHEET
SVP series
Test item
Damp heat (Steady state)
(After V.P.S test)
Test temperature
60 deg.C
Model
Test humidity
90 % RH
Lot No.
20SVP150M
080102311
Change in capacitance (120Hz)
Tangent of loss angle (120Hz)
Tangent of loss angle
20
Percent delta [%]
10
0
-10
-20
-30
-40
1000
0
Time[h]
ESR (100kHz)
Leakage current (20V 60s)
200
180
160
140
120
100
80
60
40
20
0
10000
1000
100
10
1
0.1
0.01
0
1000
Time[h]
Note:
1000
Time[h]
Leakage current(µA)
ESR(mohm)
0
0.15
0.14
0.13
0.12
0.11
0.1
0.09
0.08
0.07
0.06
0.05
0.04
0.03
0.02
0.01
0
0
1000
Time[h]
n =20p.
Note: V.P.S test conditions : 230deg.C×75s×2times
(V.P.S = Vapor Phase Soldering method)
Start on October 22, 2000
Executed by M. Koyama
End on December 3, 2000
Drawn by M. Kimura
No.OS02D-DHSVP055
OS Engineering Department, OS-CON Control Department, Saga SANYO Industries Co., Ltd.