SANYO OS-CON20SVP22M

OS-CON DATA SHEET
No.OS02N-DFSVP016
OS-CON 20SVP22M
Frequency (kHz)
Impedance (ohm)
ESR (ohm)
0.12
68.10
0.60
0.5
16.40
0.21
1
8.24
0.14
10
0.843
0.064
100
0.103
0.047
500
0.041
0.036
1000
0.033
0.033
5000
0.060
0.032
10000
0.113
0.039
Frequency characteristics
1000
Impedance (ohm)
ESR (ohm)
ESR, Impedance (ohm)
100
10
1
0.1
0.01
0.001
0.1
1
10
100
1000
10000
Frequency (kHz)
Measureing equipment: HP4194A
Test fixture: HP16047C
Measuring position: root of leads
OS Engineering Department, OS-CON Control Department
Saga SANYO Industries Co., Ltd.
n = 3p.(Ave.)
Room temperature
OS-CON DATA SHEET
SVP series
Test item
Endurance
(After V.P.S test)
Test temperature
105 deg.C
Model
Applied voltage
20 V
Lot No.
20SVP22M
152022411
Tangent of loss angle (120Hz)
Change in capacitance (120Hz)
Tangent of loss angle
20
Percent delta [%]
10
0
-10
-20
-30
-40
2000
0
Time[h]
ESR (100kHz)
Leakage current (20V 60s)
10000
200
180
160
140
120
100
80
60
40
20
0
1000
100
10
1
0.1
0.01
0
2000
Time[h]
Note:
2000
Time[h]
Leakage current(µA)
ESR(mohm)
0
0.15
0.14
0.13
0.12
0.11
0.1
0.09
0.08
0.07
0.06
0.05
0.04
0.03
0.02
0.01
0
0
2000
Time[h]
n =30p.
Note: V.P.S test conditions : 230deg.C×75s×2times
(V.P.S = Vapor Phase Soldering method)
Start on June 13, 2001
Executed by M. Koyama
End on September 4, 2001
Drawn by M. Kimura
No.OS02D-DESVP016
OS Engineering Department, OS-CON Control Department, Saga SANYO Industries Co., Ltd.
OS-CON DATA SHEET
SVP series
Test item
Damp heat (Steady state)
(After V.P.S test)
Test temperature
60 deg.C
Model
Test humidity
90 % RH
Lot No.
20SVP22M
152022411
Change in capacitance (120Hz)
Tangent of loss angle (120Hz)
Tangent of loss angle
20
Percent delta [%]
10
0
-10
-20
-30
-40
1000
0
Time[h]
ESR (100kHz)
Leakage current (20V 60s)
200
180
160
140
120
100
80
60
40
20
0
10000
1000
100
10
1
0.1
0.01
0
1000
Time[h]
Note:
1000
Time[h]
Leakage current(µA)
ESR(mohm)
0
0.15
0.14
0.13
0.12
0.11
0.1
0.09
0.08
0.07
0.06
0.05
0.04
0.03
0.02
0.01
0
0
1000
Time[h]
n =20p.
Note: V.P.S test conditions : 230deg.C×75s×2times
(V.P.S = Vapor Phase Soldering method)
Start on June 13, 2001
Executed by M. Koyama
End on July 24, 2001
Drawn by M. Kimura
No.OS02D-DHSVP016
OS Engineering Department, OS-CON Control Department, Saga SANYO Industries Co., Ltd.