SANYO 6SVP220MX

OS-CON DATA SHEET
No.OS02N-DFSVP031
OS-CON 6SVP220MX
Frequency (kHz)
Impedance (ohm)
ESR (ohm)
0.12
5.914
0.155
0.5
1.444
0.086
1
0.733
0.071
10
0.095
0.046
100
0.032
0.030
500
0.030
0.028
1000
0.040
0.028
5000
0.099
0.032
10000
0.145
0.035
Frequency characteristics
1000
Impedance (ohm)
ESR (ohm)
ESR, Impedance (ohm)
100
10
1
0.1
0.01
0.001
0.1
1
10
100
1000
10000
Frequency (kHz)
Measureing equipment: HP4194A
Test fixture: HP16047C
Measuring position: root of leads
OS Engineering Department, OS-CON Control Department
Saga SANYO Industries Co., Ltd.
n = 3p.(Ave.)
Room temperature
OS-CON DATA SHEET
SVP series
Test item
Endurance
(After V.P.S test)
Test temperature
105 deg.C
Model
Applied voltage
6.3V
Lot No.
6SVP220MX
1N1702221
Tangent of loss angle (120Hz)
Change in capacitance (120Hz)
Tangent of loss angle
20
Percent delta (%)
10
0
-10
-20
-30
-40
2000
0
Time[h]
ESR (100kHz)
Leakage current (6.3V 60s)
10000
100
90
80
70
60
50
40
30
20
10
0
1000
100
10
1
0.1
0.01
0
2000
Time[h]
Note:
2000
Time[h]
Leakage current(µA)
ESR(mohm)
0
0.15
0.14
0.13
0.12
0.11
0.1
0.09
0.08
0.07
0.06
0.05
0.04
0.03
0.02
0.01
0
0
2000
Time[h]
n =30p.
V.P.S test conditions : 230deg.C×75s×2times
(V.P.S = Vapor Phase Soldering method)
Start on December 13, 2001
Executed by M. Koyama
End on March 6, 2002
Drawn by M. Kimura
No.OS02D-DESVP031
OS Engineering Department, OS-CON Control Department, Saga SANYO Industries Co., Ltd.
OS-CON DATA SHEET
SVP series
Test item
Damp heat (Steady state)
(After V.P.S test)
Test temperature
60 deg.C
Model
Test humidity
90 % RH
Lot No.
6SVP220MX
1N1702221
Change in capacitance (120Hz)
Tangent of loss angle (120Hz)
Tangent of loss angle
20
Percent delta (%)
10
0
-10
-20
-30
-40
1000
0
Time[h]
ESR (100kHz)
Leakage current (6.3V 60s)
100
90
80
70
60
50
40
30
20
10
0
10000
1000
100
10
1
0.1
0.01
0
1000
Time[h]
Note:
1000
Time[h]
Leakage current(µA)
ESR(mohm)
0
0.15
0.14
0.13
0.12
0.11
0.1
0.09
0.08
0.07
0.06
0.05
0.04
0.03
0.02
0.01
0
0
1000
Time[h]
n =20p.
V.P.S test conditions : 230deg.C×75s×2times
(V.P.S = Vapor Phase Soldering method)
Start on December 13, 2001
Executed by M. Koyama
End on January 24, 2002
Drawn by M. Kimura
No.OS02D-DHSVP031
OS Engineering Department, OS-CON Control Department, Saga SANYO Industries Co., Ltd.